Precision cut-off tools for accurate grooving and part-off operations
Cut-off tools are narrow holder systems for lathes designed to produce precise grooves and part-offs, offering reliable control when machining steels and other workpiece materials where clean separation is essential. They serve as either solid clamp-style holders or flat tool blades fitted with indexable carbide inserts, and when equipped with internal coolant channels they deliver high-pressure coolant directly to the insert to control heat and evacuate chips efficiently. Using these tools reduces the risk of chip jamming, surface damage and sudden tool failure while improving repeatability, particularly in deep grooving and tough materials where external coolant is insufficient. Key advantages include enhanced cutting stability, extended insert life and consistent part quality through optimised chip evacuation and thermal management.
12mm Grooving Toolholder 2mm Cutting Width, 16mm Max Depth, ISO 1212, For 2C MGM Inserts, Right-Hand Cutting - Teknik Makina
Take advantage of precise right‑hand parting with a 2 mm cutting width and 16 mm maximum cutting depth for controlled chip evacuation and reliable cycle times; combine compact dimensions and robust clamping for consistent production. Order the holder via Metav Werkzeuge or consult our technical advisors for application matching. Teknik Makina Parting clamp holder D658TM — right‑hand, 2 mm cutting width The parting clamp holder is designed for controlled right‑hand grooving and parting operations with indexable inserts, delivering compact stability for workshop and light‑industrial turning applications. Right‑hand cutting for conventional setups 2 mm cutting width for narrow grooves Max parting depth 16 mm Compatible with Korloy 2C MGM inserts Precision where narrow grooves matter The holder provides a focused solution when space on the turned workpiece is limited: the 2 mm cutting width makes fine parting and narrow‑groove operations repeatable while the right‑hand cutting geometry ensures predictable chip flow. By concentrating cutting forces in a small contact zone, the tool reduces vibration and permits consistent surface finish in serial turning and finishing operations. This benefit is particularly relevant for workshops machining small components where dimensional control and minimal material loss are required. Stable construction for reliable cycles With a 12 mm clamping head and a compact 125 mm overall length, the design promotes rigidity without adding unnecessary overhang. The reduced mass (0.162 kg) lowers centrifugal load at higher spindle speeds and helps maintain concentricity during short, repetitive cuts. The clamping concept secures the insert firmly, translating into stable cuts and extended insert life. These mechanical advantages support improved uptime and predictable tool replacement intervals, which in turn aid process planning and cost control. Fast integration and proven compatibility Compatibility with Korloy 2C MGM indexable inserts and the ISO 1212 holder designation simplifies procurement and tool‑life management across mixed fleets. The mount accepts the 2C‑R MGM bar format, allowing straightforward retrofitting into existing tool posts and reducing setup time at the turret. For production planners this means fewer special holders to stock and faster changeovers between parting operations, yielding a measurable improvement in shopfloor throughput without compromising precision. For application advice or to confirm suitability of the Teknik Makina parting clamp holder D658TM with existing Korloy inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D658TM Manufacturer: Teknik Makina Core data Cutting head width: 12 mm Cutting width: 2 mm Maximum parting depth: 16 mm Overall length: 125 mm Weight: 0.162 kg Cutting direction: right Special features Compatible with Korloy 2C MGM inserts ISO designation: 1212 Mounting bar designation: 2C‑R MGM Suitable for indexable insert parting operations FAQ Which insert types fit this holder? The holder is compatible with Korloy 2C MGM indexable inserts and accepts the 2C‑R MGM mounting bar format; using the specified insert type ensures correct clamping and cutting performance. What is the maximum cutting depth for the holder? Maximum parting depth is 16 mm, which balances effective material removal with rigidity for controlled groove profiles. Is the tool suitable for left‑hand cutting? No, the design is for right‑hand cutting only; left‑hand operations require a dedicated left‑hand holder. What does the ISO 1212 designation indicate? The ISO 1212 designation describes the holder form and interface for indexable insert parting tools, simplifying selection and compatibility checks across tool systems. How compact is the holder for turret mounting? With an overall length of 125 mm and a 12 mm clamping head, the holder is compact and well suited to minimising overhang on standard turrets for short to medium parting cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Mini Clamping Holder 88mm, M6 Thread - Teknik Makina
Take advantage of a compact, stiff clamp design with a 5 mm shank and secure M6 thread for reliable toolholding in confined setups; order directly via Metav Werkzeuge or consult the Metav team for technical advice and availability. Mini clamp holder DC320TM – compact clamp holder with 5 mm shank and M6 thread (Teknik Makina) The Mini clamp holder DC320TM is a compact clamp holder engineered for precise, secure clamping in small machining and tooling arrangements. Compact design for tight toolposts 5 mm shank for small tool holders M6 fixing thread for secure attachment 88 mm overall length, 12 mm body diameter Space-saving stiffness for more consistent machining The compact construction delivers a high stiffness-to-size ratio, allowing stable clamping where space is limited. Reduced tool movement leads to fewer vibrations and a more consistent surface finish, which in turn supports shorter cycle times and less rework. The compact format is particularly beneficial in small-batch production or when multiple tools must be mounted close together, offering a reliable way to keep setups compact without sacrificing performance. Clear dimensions and simple integration into existing systems Key dimensions are provided for straightforward integration: a 5 mm shank, a 12 mm body diameter, an M6 thread and an 88 mm overall length, with a net weight of 0.067 kg. The slim shank suits small toolholders and accessory adaptors, while the thread specification ensures compatibility with common clamping screws. These concrete values enable planners and buyers to verify fitment quickly and reduce trial-and-error at the machine. Fast assembly and stable clamping reduce downtime The straightforward attachment concept and standard thread size deliver a short setup time and predictable clamping behaviour. Fewer adjustments at the machine mean less downtime between operations; the result is a small but practical improvement in production flow. For workshops consolidating tooling stock, the holder’s compact profile supports denser tool layouts and quicker changeovers, benefitting operational efficiency. Trusted supply chain and practical procurement Sourcing the holder from a reliable distributor ensures consistent availability and traceable quality. Metav combines a broad industrial range with local warehouse supply from Emmerich, backed by a history of satisfied customers. With a reputation built on accessibility and dependable logistics, Metav supports single-source procurement strategies that reduce administrative overhead and maintain steady workshop supply. Contact Metav Werkzeuge to confirm suitability for specific toolposts and to check stock status at the Emmerich warehouse Technical Data Article number: DC320TM Manufacturer: Teknik Makina Weight: 0.067 kg Key dimensions Shank diameter: 5 mm Body diameter: 12 mm Overall length: 88 mm Thread: M6 Features Mini clamp holder Story trigger: klemmhalter SKU: DC320TM FAQ What materials and operations is this clamp holder designed for? The Mini clamp holder DC320TM is a general-purpose clamping component suitable for small tooling assemblies; material-specific suitability depends on the tool and machine configuration. How is the holder secured to the toolpost? Fixing is via the M6 thread, which provides a standard interface for clamping screws and secure attachment in compact setups. Which shank size must the toolholder accept? The holder uses a 5 mm shank, so a compatible receiver or adaptor with a 5 mm acceptance bore is required for proper installation. Is this item lightweight enough for quick tool changes? At 0.067 kg, the DC320TM is lightweight and supports rapid handling during tool changes while maintaining sufficient stiffness for many small-scale machining tasks. Can the DC320TM be used on CNC lathes or manual lathes? The component is suitable for both CNC and manual lathe setups provided the toolpost or adapter accepts the specified shank and thread dimensions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Mini Stech Clamping Holder D12 d03 L88, Precision Miniature Tool Holder - Teknik Makina
Take advantage of the compact 12 mm shank and 88 mm overall length for precise small-diameter operations; the balance of reach and rigidity supports stable machining. Order the product directly via Metav Werkzeuge or consult our technical advisors for suitability. Mini clamp holder D12 d03 L88 – 12 mm compact clamp holder by Teknik Makina A Mini clamp holder for compact turning and small‑diameter machining that combines a 12 mm shank with an 88 mm overall length for space‑limited setups and reliable clamping. 12 mm shank for tight toolholders 88 mm overall length for balanced reach Space-saving compact design Precision clamping interface Optimised rigidity and reach for tight setups The compact design delivers a balance between rigidity and reach: the short 88 mm overall length reduces cantilevering while the 12 mm shank keeps the holder suitable for dense toolpost arrangements. For small‑diameter applications this means fewer vibrations and improved surface finish. The construction supports repeatable position and alignment, helping to keep cycle times consistent while maintaining accuracy in close‑quarter machining environments. Precision clamping that simplifies setup and repeatability A clear advantage of this clamping solution is the precision clamping interface, which allows quick, stable fixation of the cutting element. The clamping mechanism is designed to ensure consistent seat contact and minimal play, improving repeatability across batches. For workshops that value predictable results, the compact holder reduces the need for frequent re‑adjustment and streamlines setup procedures in serial production or prototyping. Versatile use in small‑diameter turning and finishing tasks Designed for compact turning operations, the holder is particularly suitable where space constraints demand a slim toolholder without sacrificing control. The compact form factor supports finishing passes and light roughing on small shafts and components. Explained simply: a shorter, accurately machined holder keeps the tool closer to the spindle, which reduces deflection and helps achieve tighter tolerances on critical features. Practical information for integration and selection The product is supplied with a clear designation and SKU for easy procurement and inventory control. The compact format makes integration into existing toolposts straightforward when the machine accepts a 12 mm‑diameter shank. When selecting tooling, consider the balance between reach and stiffness required by the component geometry; the reduced projection of this holder generally favours improved surface quality and tool life in constrained setups. Choose the Teknik Makina mini clamp holder DC300TM for compact precision — contact Metav Werkzeuge for application advice and reliable supply from Emmerich. Technical data Article number: DC300TM Name: Mini clamp holder D12 d03 L88 Product type: Mini clamp holder Label: 12mm Mini-Stechklemmhalter L88mm eClass: 21181005 Brand: Teknik Makina Facts Diameter: 12 mm Overall length: 88 mm UID/SKU: DC300TM Special features Compact design Precision clamping interface Suitable for small‑diameter turning Category: Machining / Cutting FAQ What is the shank diameter of the holder? The shank diameter is 12 mm for the Teknik Makina mini clamp holder DC300TM, enabling use in compact toolpost arrangements. How long is the toolholder overall? The overall length is 88 mm, which provides a balance of reach and stiffness for small‑diameter operations with the DC300TM. Is the holder suitable for finishing small shafts? Yes, the compact format and stable clamping interface make this holder appropriate for finishing and light roughing on small shafts. How is repeatability ensured with this holder? Repeatability is achieved through the precision clamping interface and short projection, both features of the Teknik Makina DC300TM mini clamp holder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Mini Steck Clamping Holder D12 D06 L88, Precision Miniature Clamping - Teknik Makina
Compact 12 mm form factor combined with an 88 mm overall length delivers space-efficient, repeatable performance for parting and grooving operations. Benefit from precise clamping and reduced vibration for improved surface finish; order the Mini-Stechklemmhalter DC321TM directly via Metav Werkzeuge or ask our consultants if needed. Mini-Stechklemmhalter D12 d06 L88 – 12 mm mini clamp holder by Teknik Cutting Tools A compact clamp holder designed for parting and grooving in confined toolposts, featuring a 12 mm shank and an 88 mm overall length for space-critical machining. Slim 12 mm shank for tight toolposts 88 mm overall length for compact setups Stable clamping for consistent surface finish Space-saving precision for confined toolposts The 12 mm shank and 88 mm overall length make this mini clamp holder ideal where clearance is limited. Its reduced envelope enables closer tool placement and denser toolpost setups, which supports shorter tool overhangs and thereby lowers bending moments. The result is improved repeatability and a measurable reduction in workpiece deviation during parting or grooving tasks — a practical advantage in small-batch production and prototype machining where fixture space is at a premium. Stable clamping that improves finish and cycle reliability A well-engineered clamping geometry provides stability under cutting loads, helping to suppress chatter and minimise tool deflection. By securing the cutting edge more rigidly, the holder contributes directly to a consistent surface finish and longer effective insert life. For operations where every micrometre counts, this holder translates mechanical restraint into fewer reworks and a steadier machining cycle time, supporting predictable throughput in mixed-production environments. Straightforward integration into existing lathe toolposts Designed as a compact component for standard toolposts, the mini clamp holder is simple to fit and align. The compact design reduces changeover effort between setups and lowers the need for customised fixtures. Identified as DC321TM, the holder can be catalogued and referenced easily for maintenance planning and inventory control, facilitating faster procurement and fewer tooling interruptions on the shop floor. Practical benefits for workshops and small-scale manufacturers Choosing a compact holder like this one supports leaner tooling strategies: less interference, faster clamping, and better use of limited turret positions. The technical simplicity of the design translates into operational confidence — machines stay productive and set-up times shrink. Paired with Metav’s commitment to reliable supply from Emmerich, buyers gain both a functional component and the assurance of consistent availability for repeat orders. Choose the Teknik Cutting Tools mini clamp holder DC321TM for compact precision and contact Metav Werkzeuge in Emmerich for ordering and tailored technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: DC321TM Product type: Mini clamp holder Label: 12mm Mini-Stechklemmhalter L88mm Core data Diameter: 12 mm Overall length: 88 mm ECLASS: 21181005 Special features Manufacturer: Teknik Makina UID: DC321TM Product designation: Mini-Stechklemmhalter FAQ What shank diameter does the holder support? The holder is specified with a 12 mm shank diameter and is intended for compact toolholder arrangements. What is the overall length and why does it matter? The overall length is 88 mm; a shorter profile helps reduce overhang, lowering deflection and improving machining stability. Is this holder suitable for standard lathe toolposts? Yes, the design of the Mini-Stechklemmhalter DC321TM allows straightforward fitting to common compact toolpost systems used in parting and grooving. How is the product identified for ordering and stock control? The item is listed under SKU/Article number DC321TM, which simplifies reordering and inventory tracking. Which manufacturer produces this mini clamp holder? The component is made by Teknik Makina and supplied under the designation Mini-Stechklemmhalter, DC321TM, for compact parting applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Mini Tool Holder 88mm Overall Length M6 Thread - Teknik Makina
Benefit from a compact, low-mass design combined with a secure M6 mounting for reliable parting and grooving cycles; order or request availability through Metav Werkzeuge for straightforward integration into small turning centres. Mini-Stechklemmhalter – Mini parting clamp holder, 12 mm diameter, M6 thread (Teknik Makina) A Mini-Stechklemmhalter crafted for secure parting and grooving in compact turning setups, ideal where space is limited and repeatable clamping is required. Compact 88 mm overall length 12 mm cutting diameter compatibility M6 thread for secure mounting Only 0.075 kg for low inertia Increased process reliability through compact clamping The compact construction delivers a stable clamping interface in confined setups. With an overall length of 88 mm and a small form factor, the holder reduces overhang and helps maintain concentricity during cut-off operations. The lightweight nature contributes to reduced dynamic forces, which supports repeatable results when machining short-facing and parting tasks. This benefits workshops that prioritise consistent component tolerances and short setup times. Secure mounting and mechanical simplicity Featuring an M6 thread and a standard 4 mm shank reception, the component secures quickly and precisely into compatible toolposts or adapters. The straightforward mechanical design minimises adjustment effort while ensuring a tight hold for parting blades with up to 12 mm effective diameter. Such a simple interface shortens fixture time and lowers the risk of misalignment, so cycle reliability is improved without complex fixturing. Space-saving design for small lathes and finishing stations Designed for compact turning centres, the low profile and minimal mass of the clamp holder reduce the occupied envelope at the turret or toolpost. This makes it suitable for dense tool arrays and multi-station setups where conserving radial and axial space is essential. The reduced inertia of the assembly enhances responsiveness during feed changes, contributing to smoother cut-off transitions and less vibration during interrupted cuts. Practical integration and workshop advantages Supplied as a precise mechanical clamp, the holder supports fast changeovers and straightforward tool positioning. The balance between a small diameter interface and secure thread mounting supports efficient workflow in small-batch production and maintenance tasks. Available under the SKU DC310TM, the item is intended as a pragmatic solution for shops seeking compact, reliable parting performance without extensive retooling. Discuss compatibility and availability with Metav Werkzeuge: info@metav-werkzeuge.com or +49 2822 7131930 — specialists can advise on the Teknik Makina DC310TM mini parting clamp holder Technical data Article number: DC310TM Designation: Mini parting clamp holder Brand: Teknik Makina Facts Diameter: 12 mm Shank reception diameter: 4 mm Thread: M6 Overall length: 88 mm Weight: 0.075 kg Special features Compact design for limited spaces Mechanical clamping for parting and grooving Low mass to reduce toolholder inertia FAQ What tool diameter is supported by the holder? The holder accommodates a 12 mm cutting diameter, providing a compact interface for small parting blades and narrow grooving tools. How is the clamp holder secured to the toolpost? Mounting is achieved via an M6 thread together with the 4 mm shank reception; the DC310TM uses this mechanical interface for a secure fit. Is the holder suitable for heavy-duty cut-off operations? The DC310TM is optimised for compact setups and low-inertia applications; suitability for heavy-duty tasks depends on machine capacity and tool selection. Can the component be used in multi-station turrets? Yes, the compact length and low weight make it suitable for dense tool arrangements and finishing stations where space is limited. Which SKU should be referenced when ordering or enquiring? Please refer to SKU DC310TM when requesting stock or technical details for the Technik Makina mini parting clamp holder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm SEL 1212 J16- IR16 For 16 IR Indexable Inserts Left-Hand Cutting Interior Cooling - Teknik Makina
Benefit from precise clamping, compatibility with 16 IR indexable inserts and a compact 110 mm form for reliable left-hand turning operations; order the clamping holder directly via Metav Werkzeuge or consult our technical advisors for application support. SEL 1212 Clamping Holder D508TM — left-hand turning holder for 16 IR inserts (Teknik Makina) SEL 1212 Clamping Holder D508TM is a left-hand turning toolholder designed for secure clamping of 16 IR indexable inserts in compact machining setups. SEL 1212 ISO turning toolholder For 16 IR indexable inserts Left-hand cutting orientation Compact 110 mm overall length Stable clamping for precise turning results The SEL 1212 design focuses on secure clamping to reduce vibration and maintain repeatable cutting geometry. With a compact clamping head and a robust fixing method, the holder gives consistent tool position, which translates into improved surface finish and longer insert life. The holder’s left-hand configuration suits turning operations that require negative lead or specific approach angles, and its secure clamping prevents micro-movements that can compromise dimensional accuracy during medium-duty turning. Faster set-up through standardised insert compatibility Compatibility with 16 IR indexable inserts and the specified shank designation simplifies tooling logistics and changeovers. The adapter fits common insert geometries, so tool changes and insert indexing take less time, reducing machine downtime. For workshops seeking a predictable production flow, the standard ISO-style sizing and the clear designation (SEL 1212) make integration with existing toolholders straightforward, supporting efficient process planning and lower overall tooling costs. Compact dimensions for accessibility and rigidity A reduced overall length and modest mass deliver both accessibility in tight setups and a favourable stiffness-to-reach ratio. The holder’s overall length of 110 mm, cutting head width of 16 mm and a cutting height of 22 mm are balanced to keep the tool close to the workpiece while maintaining rigidity. The low weight of 0.119 kg helps reduce centrifugal forces on rotating assemblies and improves dynamic stability during higher spindle speeds, supporting smoother cuts and reduced chatter on small to medium components. Practical partner for everyday workshop use Supplied in a standard ISO SEL 1212 form, this clamping holder is intended for straightforward integration into production or jobbing environments. The clear mechanical specifications make planning tooling inventories easier and help maintain process consistency across batches. As part of a trusted supply chain, Metav Werkzeuge supports dependable delivery and product selection, backed by decades of experience in precision tooling and an extensive product range to reduce procurement complexity. For tailored advice on applying the SEL 1212 clamping holder (D508TM) in specific turning tasks, contact Metav Werkzeuge for expert guidance and reliable supply from Emmerich at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: D508TM Brand: Teknik Makina ISO designation: SEL 1212 Compatible inserts: 16 IR Shank/bar designation: J16- IR16 Dimensions & weight Overall length: 110 mm Weight: 0.119 kg Cutting head width: 16 mm Holder height: 12 mm Holder width: 12 mm Cutting height: 22 mm Features Left-hand cutting orientation For indexable inserts 16 IR SEL 1212 clamping system Suitable for standard turning operations FAQ Which insert size fits this holder best? The SEL 1212 clamping holder (D508TM) is designed for 16 IR indexable inserts, ensuring standardised fit and simple insert replacement. Is the holder suitable for right-hand turning? This variant is configured for left-hand cutting direction; for right-hand operations, a corresponding right-hand holder should be chosen. What are the key dimensions to check for fixture clearance? Check the overall length of 110 mm, cutting head width 16 mm and cutting height 22 mm to confirm access and clearance in the intended set-up. Can the D508TM be used in short-reach, high-rigidity applications? Yes, the compact form and modest mass (0.119 kg) make the D508TM suitable where tool accessibility and stiffness are both needed. What shank or bar designation is compatible with this holder? The holder references the designation J16- IR16, which aligns with standard shank formats for this insert size. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 1212 2C DGN For DGN 2C Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, precise holder that combines a 12 mm clamping section and a 125 mm overall length to support efficient grooving and parting operations; order the parting tool holder directly via Metav Werkzeuge or consult our specialists for application advice. Parting tool holder DGN — grooving and parting holder with 12 mm clamp, Teknik Makina Parting tool holder DGN is a compact grooving and parting holder designed for industrial turning applications, optimised for ISCAR DGN 2C inserts and short-reach operations Compact 12 mm clamp width for tight grooves Compatible with ISCAR DGN 2C inserts M4x10 hex screw with T15 key for secure clamping 125 mm overall length for stable tool mounting Precision performance in tight spaces The DGN parting holder delivers precise positioning thanks to its standardised 12 mm clamp and ISO 1212 reference, which together reduce play and ensure repeatable cuts. Designed for short overhangs, the holder’s 125 mm overall length minimises deflection during cut-off and grooving tasks, improving dimensional accuracy and surface finish. This compact geometry is particularly useful where machine-tool clearance is limited and consistent cutting performance is required. Secure clamping and straightforward maintenance Clamping is effected with an M4x10 hex screw tightened using a T15 hex key, providing a reliable connection between holder and insert without complex adjustments. The simple clamping mechanism speeds up insert changes and routine checks, reducing downtime. At a mere 0.14 kg, the holder is light enough for quick handling while remaining rigid during operation, making maintenance procedures faster and less physically demanding. Compatibility that simplifies tooling logistics Specified for DGN 2C inserts and tested for use with ISCAR cutting grades, the holder integrates seamlessly into existing tooling setups that already use DGN-format inserts. The standardised interface permits straightforward interchangeability of inserts and supports common workpiece materials encountered in high-quality steel machining. This compatibility eases inventory management and lowers the barrier to adopting specialised grooving operations on the shop floor. Practical limits and application focus The holder supports a maximum plunge depth of 12 mm and a cutting width of 2 mm, parameters that define its suitability for narrow-slot and parting operations. These limits make the tool ideal for finishing narrow grooves, parting small-diameter workpieces and operations that prioritise surface integrity over bulk material removal. For heavy interrupted cuts or deep shoulder grooving, select tooling with larger cross-sections or greater overhang capacity. For reliable grooving and precise parting operations, select the Teknik Makina DGN parting tool holder via Metav Werkzeuge — contact our consultants for tailored recommendations and to confirm fitment in specific turning applications Technical data Article number: D019TM Manufacturer: Teknik Makina Numbers / Core technical data Clamp width: 12 mm Clamp height: 12 mm Cutting head width: 12.2 mm Overall length: 125 mm Overall height: 12 mm Max plunge depth: 12 mm Cutting width: 2 mm Weight: 0.14 kg Special features Compatible inserts: DGN 2C Suitable for insert brand: ISCAR Hex screw: M4x10 Hex key: T15 ISO designation: 1212 Holder bore designation: 2C DGN FAQ What insert types are compatible with this holder? The parting tool holder DGN accepts DGN 2C inserts and is specified for use with ISCAR DGN grades, ensuring plug‑and‑play compatibility for common grooving inserts. What is the maximum cutting depth for this holder? The holder supports a maximum plunge depth of 12 mm, which defines its effective range for grooving and cut‑off tasks. Which screw and key are required for clamping the insert? Clamping is secured with an M4x10 hex screw and requires a T15 hex key for correct torque and repeatable fixation. Is this holder suitable for steel machining? Yes; the holder is designed for high-quality steel machining, matching the demands of accurate grooving and parting in industrial lathe work. How does the holder affect tool rigidity and accuracy? With a compact 125 mm overall length and a 12 mm clamp, the design minimises overhang and reduces deflection, which improves cutting accuracy and surface finish during parting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 1212 2C KGMN 200 For KGMN 200 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of precise, repeatable parting operations thanks to secure clamping and a narrow 2 mm cutting width, combined with quick insert compatibility for efficient changeovers; order directly from Metav Werkzeuge or contact our consultants for compatibility advice. Parting tool holder KGMN — 12 mm height, 2 mm cut width, Teknik Makina A compact Parting tool holder KGMN engineered for controlled parting and grooving on lathes and turning centres, designed around Korloy KGMN 200 inserts for reliable metal‑cutting applications. Parting tool holder for KGMN 200 inserts 2 mm cutting width for narrow grooves Secure clamp with M4x10 fastening 125 mm overall length, 12 mm height Consistent clamping for precision parting A sturdily machined clamp body provides reliable fixation of the insert, reducing movement under load and helping to sustain repeatable tolerances. The holder’s M4x10 fastening and supplied hex key size T15 ensure a firm, serviceable connection between insert and bar; this straightforward mechanical design keeps set‑up times short and maintenance predictable. For shops seeking process stability, the compact geometry contributes to reduced vibration and steadier finish quality on workpieces. Narrow‑groove performance that improves surface quality With a 2 mm cutting width and a cutting‑head envelope of 12.2 mm, the holder is optimised for tight parting and grooving operations where clearance is limited. The maximum plunge depth of 12 mm gives sufficient engagement for many through‑parting and grooving jobs while the slim cut width minimises material removal and cutting forces. In practice this translates to less heat buildup, a cleaner chip flow and better surface integrity on the finished component. Built for efficient workshop handling Weighing just 0.13 kg and finished to standardised ISO dimensions (ISO 1212), the holder is easy to handle during tool changes and aligns with common bar systems. The overall length of 125 mm and a total height of 12 mm fit compact tool posts and allow rapid indexing in many turning centres. The low mass reduces inertial forces during acceleration, helping to preserve insert life and enabling confident, repeatable setups in production or jobbing environments. Compatibility and quick changeover with Korloy inserts Designed specifically for Korloy KGMN 200 inserts and documented as compatible with bar designation 2C KGMN 200, the holder supports fast replacement of cutting edges and straightforward tool management. The adherence to recognised insert geometry and the presence of a standard clamping screw mean swaps are predictable and can be integrated into existing tool‑holding inventories. Where machining flexibility matters, this holder provides a compact, industry‑aligned option for parting and grooving tasks. Contact Metav Werkzeuge for technical advice and to arrange supply of this Teknik Cutting Tools parting tool holder from our Emmerich warehouse. Technical data Article number: D016TM Manufacturer: Teknik Makina eClass: 21181005 Dimensions & weight Holder width: 12 mm Holder height: 12 mm Cutting head width: 12.2 mm Cutting width: 2 mm Max plunge depth: 12 mm Overall length: 125 mm Overall height: 12 mm Weight: 0.13 kg Compatibility & fastenings Compatible with Korloy KGMN 200 inserts Bar designation: 2C KGMN 200 Clamping screw: M4x10 Hex key size: T15 ISO designation: 1212 FAQ What insert type fits this holder? The holder is compatible with Korloy KGMN 200 inserts and accepts the standard geometry used for that series. What is the cutting width and how does that affect use? The 2 mm cutting width allows narrow parting and grooving where minimal material removal and low cutting forces are required. Which fastening components are included or required? Fastening is by an M4x10 screw; torque should be applied with a T15 hex key to secure the insert correctly. Is the holder suitable for production turning centres? Yes — the compact parting tool holder KGMN with 125 mm overall length and ISO‑aligned dimensions is designed for reliable use in production and jobbing environments. How deep can the holder cut in a single plunge? The maximum plunge depth is 12 mm, suitable for many through‑parting and groove‑cutting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 1212 2C-DGM 2 For 2C DGM 2 Wendeplatten Innenkühlung - Rechtsschneidend - Teknik Makina
Take advantage of the compact 12 × 12 mm clamping cross-section together with a 2 mm cutting width and up to 16 mm plunge depth for precise, repeatable grooving and parting operations; order the holder directly via Metav Werkzeuge or consult the team for application advice. Parting and Grooving Clamping Holder – 2 mm cutting width, 16 mm max plunge (Teknik Makina) A sturdy Parting and Grooving Clamping Holder for use with indexable inserts, engineered for precise 2 mm grooving and controlled parting in standard turning set-ups *Compatible with TNGLY-OKE 2C DGM 2 inserts *2 mm cutting width for fine grooving *Max plunge depth 16 mm for deep cuts *Compact 12 x 12 mm clamping cross-section Stable clamping for repeatable groove geometry The holder delivers consistent clamping thanks to its compact 12 × 12 mm cross-section and low overall mass (0.166 kg), which together reduce tool overhang and vibration during parting operations. With a 2 mm cutting width and 16 mm maximum plunge depth, the design supports accurate groove profiles and repeatable parting without undue deflection. For workshops that prioritise dimensional control, the combination of a short, rigid shank and a secure clamp ensures improved surface finish and fewer reworks. The use of indexable inserts means straightforward insert replacement and predictable cutting behaviour. Rapid integration into lathe toolposts and clear interface data Integration into existing tooling is simplified by the standardised shank and designation data: ISO designation 1212 and shank type 2C‑DGM 2 are specified for straightforward referencing in tool lists and holders. The overall length of 125 mm keeps the centre of gravity close to the machine, while the clearly defined head and shank dimensions (12 mm height and 12 mm head width) make it easy to set up in toolposts or quick-change systems. These measurable values support planning in production: matching the holder to the lathe’s toolpost geometry avoids unnecessary adapters and preserves rigidity at the cutting point. Practical reliability for everyday turning tasks and workshop efficiency Built for routine use with TNGLY‑OKE indexable inserts, this clamping holder balances simplicity with robust function. The compact format and defined mechanical interfaces reduce set-up variability and support a steady production rhythm. Metav’s emphasis on accessible precision means this product is supported from stock in Emmerich, backed by decades of distribution experience and a broad portfolio that helps reduce supplier complexity. The result is a dependable solution that fits into established workflows and helps maintain consistent throughput. Contact Metav Werkzeuge for tailored advice on integrating this Teknik Makina parting and grooving holder into production; Metav Werkzeuge in Emmerich provides fast supply and application consultation – eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: D842TM Manufacturer: Teknik Makina Type designation (ISO): 1212 Shank designation: 2C-DGM 2 Compatible insert manufacturer: TNGLY-OKE Numbers / Core technical data Cutting width: 2 mm Max plunge depth: 16 mm Clamping height: 12 mm Head width: 12 mm Clamping width: 12 mm Overall length: 125 mm Weight: 0.166 kg Special features / Design For indexable inserts: 2C DGM 2 Clamping style: parting/grooving holder ISO reference available: 1212 Short, rigid form factor for reduced vibration FAQ Which insert type fits this holder? This parting and grooving clamping holder accepts 2C DGM 2 indexable inserts and is specified for TNGLY‑OKE inserts in the product data. What is the maximum cutting width and plunge capability? The holder supports a 2 mm cutting width and a maximum plunge depth of 16 mm, suitable for fine grooving and controlled parting operations. How is the holder designated for tool lists and ordering? Refer to SKU D842TM and ISO designation 1212 for ordering and tool list entries; the shank designation 2C‑DGM 2 clarifies mounting requirements. Will this holder fit standard quick-change toolposts? The compact 12 × 12 mm clamping cross-section and the 125 mm overall length make the holder compatible with common lathe toolposts and quick-change solutions where the shank form matches. What benefits does the compact form deliver on the lathe? A shorter, rigid shank reduces overhang and vibration, improving surface finish and dimensional consistency during parting and grooving. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 1212 2C-L MGM For 2C MGM Wendeplatten Innenkühlung Linksschneidend - Teknik Makina
Taking advantage of a compact 12 x 12 mm shank combined with a 2 mm cutting width ensures precise, repeatable grooving operations and reduced setup times; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Grooving clamp holder (Stechklemmhalter) by Teknik Makina — 12 x 12 mm, 2 mm cutting width The Grooving clamp holder (Stechklemmhalter) is a left-hand grooving tool holder designed for a 12 x 12 mm shank and 2 mm cutting width, compatible with Korloy 2C MGM indexable inserts for medium-depth parting and grooving tasks. Compact 12 x 12 mm shank 2 mm cutting width for narrow grooves Left-hand cutting direction Compatible with Korloy 2C MGM inserts Accuracy and control for tight groove tolerances The compact 12 x 12 mm shank delivers a stable interface between holder and lathe toolpost, improving precision when producing narrow grooves. The slender 2 mm cutting width is suited to operations where minimal material removal is required while maintaining dimensional control. Thanks to the low mass (0.161 kg) and rigid geometry, vibration is reduced and repeatability is improved; this supports consistent part quality across batch runs and shortens rework cycles. The design is optimised for controlled chip flow and reliable clamping, which contributes to longer effective tool life and fewer interruptions. Robust clamping and clear compatibility for quick tool setup Built around an ISO-style designation and a dedicated bar configuration, the holder accepts Korloy 2C MGM plates and matches the ISO 1212 format and 2C-L MGM bar designation. The clamping concept secures indexable inserts reliably for turning and grooving tasks: indexable inserts permit fast replacement without regrinding, reducing downtime. The left-hand orientation is specified for tools that machine in the leftward cutting direction; this should be matched to the lathe’s setup. The clear nominal dimensions make tool selection straightforward for workshop engineers and purchasing teams. Productivity gains through predictable cutting limits A maximum plunge capability of 16 mm provides defined limits for deeper grooving operations within the holder’s intended range. Predictable cutting parameters and the holder’s compact footprint help to maintain cycle-time targets by enabling consistent feed rates and stable cutting conditions. The combination of small cutting width and secure clamping assists in achieving fine surface finishes with less secondary processing. Where part tolerances are critical, this holder supports efficient production by aligning mechanical stability with practical cutting depths. Application fit and handling considerations The holder’s modest overall length (125 mm) and clear 12 x 12 mm shank dimensions make it suitable for confined toolpost arrangements and multi-tool turrets where space is limited. Installation follows standard mounting practices for clamping holders of this class, and the left-hand cutting direction must be taken into account during tool promenade planning. Spare insert compatibility with Korloy’s 2C MGM family simplifies stocking and logistics. For users requiring further specification data or adaptation to bespoke machine interfaces, supplementary technical guidance is available to ensure the holder integrates correctly into existing tooling systems. Contact Metav Werkzeuge for tailored advice on Teknik Makina grooving clamp holders and to confirm availability from the Emmerich warehouse Technical data SKU: D607TM Manufacturer: Teknik Makina Article name: Grooving clamp holder (Stechklemmhalter) ECLASS: 21181005 Core technical data Shank height: 12 mm Shank width: 12 mm Cutting width: 2 mm Max plunge depth: 16 mm Overall length: 125 mm Weight: 0.161 kg Special features Left-hand cutting direction Compatible with Korloy 2C MGM inserts ISO designation: 1212 Bar designation: 2C-L MGM FAQ Which inserts fit this grooving holder? The grooving clamp holder (Stechklemmhalter) is compatible with Korloy 2C MGM indexable inserts as indicated in the product data. Is the cutting direction left-hand or right-hand? The holder is specified for left-hand cutting direction and should be used accordingly in lathe setups. What are the main dimensions to check for toolpost mounting? Key dimensions include the 12 x 12 mm shank height and width and an overall length of 125 mm, which determine compatibility with the toolpost or turret. What is the maximum plunge depth for grooving operations? The maximum plunge depth specified for this holder is 16 mm, defining the practical limit for parting-in operations. Is the ISO designation provided for reference? Yes — the holder’s ISO designation is listed as 1212, which aids selection and matching with corresponding insert geometries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 1212 3C DGN For DGN 3C Inserts Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, ISO‑matched holder that combines slim 12 x 12 mm shank geometry and a 125 mm overall length for straightforward integration into existing turning fixtures; its compatibility with DGN 3C inserts from ISCAR ensures quick tool changes and consistent groove width control. Order via Metav Werkzeuge or consult our specialists for application advice. DGN parting and grooving tool holder – Teknik Makina (D021TM) with 12 x 12 mm shank, 3 mm cutting width A DGN parting and grooving tool holder engineered for precise parting and grooving in lathe operations, designed to accept DGN 3C inserts and to fit ISO‑1212 shank interfaces 12 x 12 mm ISO shank profile Compatible with DGN 3C inserts from ISCAR 3 mm cutting width for narrow grooves M4x10 clamping screw with T15 key Precision and repeatability for turning processes The holder delivers a defined shank geometry with an ISO 1212 (12 x 12 mm) profile, providing stable seating in standard toolposts and ensuring repeatable positioning. This stability reduces vibration during parting operations, which in turn lowers the risk of chip entanglement and tool breakage. The slim 12 mm body and a 12.3 mm cutting‑head width allow close approach to the workpiece while the 3 mm cutting width gives consistent groove dimensions; these characteristics make the component suitable for series production where dimensional repeatability is required. Fast insert changes and secure clamping Clamping is accomplished via an M4x10 hex screw, driven with a T15 key, enabling rapid insert replacement and secure fixation of the indexable plate. The holder is intended for DGN 3C indexable inserts (manufacturer: ISCAR), so inventory management benefits from standardised insert formats. The low mass (0.13 kg) and a 125 mm overall length permit agile handling and straightforward mounting, supporting short setup times and efficient tool changes on the shop floor. Integration, versatility and application guidance With a maximum parting depth of 12 mm the tool is suited to typical grooving and parting operations on turned parts. The product has been designed for compatibility with common lathe tool posts and clamping systems that accept the 1212 designation, simplifying retrofitting into existing workflows. For complex geometries or unusual materials, technical guidance is available to determine the optimal cutting parameters and insert grades; this supports reliable results across small‑batch or high‑volume production runs. Discuss application details with Metav Werkzeuge to confirm fitment and optimise cutting parameters for specific materials and cycle times Technical Data Article number: D021TM Manufacturer: Teknik Makina Designation: Stechklemmhalter / DGN SKU: D021TM Compatible inserts: DGN 3C (ISCAR) Facts Shank width: 12 mm Shank height: 12 mm Cutting‑head width: 12.3 mm Cutting width: 3 mm Maximum parting depth: 12 mm Overall height: 12 mm Overall length: 125 mm Weight: 0.13 kg Clamping screw: M4x10 Hex key size: T15 ISO designation: 1212 Special features Designed for DGN 3C indexable inserts Compatible with ISCAR insert geometries Low mass for reduced toolpost load Standardised ISO shank for easy retrofit FAQ What inserts fit this tool holder? The holder accepts DGN 3C indexable inserts; it is specified for inserts from ISCAR and compatible geometries. What are the shank dimensions and ISO code? The shank is 12 x 12 mm, corresponding to the ISO 1212 designation for standard toolpost fitting. How deep can the holder cut or part? The maximum parting depth is 12 mm, suitable for standard grooving and parting tasks. Which screw and key are required for clamping? Clamping is with an M4x10 hex screw and requires a T15 key for secure fixation of the insert. Is the tool suitable for quick production changeovers? Yes; the low weight and standardised insert compatibility support rapid insert changes and short setup times. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 2mm Cutting Width, 16mm Max Plunge Depth, 1212, 2C-L DGN, For 2C DGN Inserts, Internally Cooled, Left-Hand Cutting - Teknik Makina
Take advantage of a compact, precision-focused design combined with reliable insert compatibility for efficient parting operations — order the tool directly via Metav Werkzeuge or consult our specialists for application guidance. Parting Tool Holder — left-hand orientation, 2 mm cutting width (Teknik Makina) A Parting Tool Holder from Teknik Makina engineered for fine left-hand grooving and parting with 2C DGN inserts for turning and CNC lathes. Compact 125 mm overall length 2 mm cutting width suited for narrow grooves Compatible with 2C DGN ISCAR inserts Left-hand cutting direction High-precision parting for narrow components The holder delivers consistently precise results when executing tight parting or grooving tasks. With a 2 mm nominal cutting width, the design minimises material removal while maintaining a stable cut profile; this is particularly valuable where component tolerances are tight or scrap must be reduced. The geometry supports predictable chip flow and repeatable engagement, making the holder suitable for series production and short-run work alike. Stable clamping with a compact footprint Engineered for compact toolpost arrangements, the holder's 125 mm overall length and square clamping dimensions (12 mm × 12 mm) provide secure fixation without imposing a large overhang. The low mass (0.158 kg) reduces vibration at the cutting zone and helps maintain surface finish and dimensional accuracy. This combination of a small footprint and robust clamping makes the tool compatible with benchtop lathes and CNC turning centres where space and rigidity are critical. Interchangeable inserts and machining parameters explained Built to accept 2C DGN inserts (compatible with ISCAR standards) and identified by ISO 1212 shank designation, the holder is straightforward to integrate into existing tooling systems. The left-hand orientation must be observed when programming or setting up operations. Maximum plunge depth is 16 mm, which is the limiting engagement for safe full-depth cuts; selecting the correct insert and feed rates ensures efficient chip control and longer insert life. The holder’s 2C-L DGN shank designation indicates intended usage with standard parting inserts and allows quick replacement when tooling wear occurs. Contact Metav Werkzeuge for tailored advice on Teknik Makina parting tool holders and secure reliable supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: D726TM Manufacturer: Teknik Makina Core specifications Overall length: 125 mm Cutting width: 2 mm Maximum plunge depth: 16 mm Clamp head width: 12 mm Clamp width: 12 mm Clamp height: 12 mm Weight: 0.158 kg Design / special features Compatible with ISCAR 2C DGN inserts ISO designation: 1212 Shank designation: 2C-L DGN Cutting direction: left FAQ What types of inserts fit this holder? The holder accepts 2C DGN style inserts; it is compatible with ISCAR 2C DGN insert types and the shank designation 2C-L DGN confirms mechanical fit. What is the maximum plunge depth for safe operation? Maximum plunge depth is 16 mm; this figure should be observed to avoid over-engagement and to maintain insert life. Is this holder suitable for right-hand turning? This particular model is manufactured for left-hand cutting direction and is intended for left-hand parting and grooving applications. Can the holder be used on compact benchtop lathes? Yes — the compact 125 mm overall length and 12 mm clamping section provide a small footprint and secure fixation suited to compact lathes and constrained toolposts. How does the holder help with surface finish and vibration? The low weight (0.158 kg) combined with the short overhang reduces chatter and supports improved surface finish during narrow parting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter 2° Cut Width 16mm Max Depth 1212 2C TD For Taegutec Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina
Take advantage of a compact, rigid toolholder that combines precise clamping and narrow cutting capability for reliable parting operations; order directly via Metav Werkzeuge or request advice from our consultants for application support. Parting clamp holder — right‑hand, 12 x 12 mm shank, for 2C TD inserts (Teknik Makina) the parting clamp holder offers a compact solution for controlled parting and grooving tasks in turning operations, designed for compatibility with indexable 2C TD inserts and short overhang applications Compatible with Taegutec 2C TD inserts Right-hand cutting direction Cutting width 2 mm for narrow grooves 125 mm overall length, compact design Consistent clamping for repeatable grooves A compact holder with a 12 x 12 mm shank and a secure clamping interface is intended to reduce vibration and promote repeatable results on serial turning tasks. The relatively low mass (0.166 kg) contributes to lower inertial forces, which can be advantageous when quick accelerations or small lathe spindles are used. Where precise groove geometry matters, a firm tool seat minimises insert movement; this is particularly relevant when working to tight dimensional tolerances. The construction supports stable cutting behaviour and helps to maintain surface quality even in confined setups. Controlled, narrow cutting for fine parting work Engineered for parting and grooving with a narrow kerf, the holder accepts inserts with a 2 mm cutting width and supports a maximum parting depth of 16 mm, enabling controlled material removal in finishing and medium-depth operations. The right-hand cutting orientation is suited to standard turning setups where the tool is mounted on the right side of the workpiece. Compatibility with the 2C TD insert geometry ensures predictable chip formation and edge contact when paired with matching Taegutec grades, allowing process planners to choose the insert grade appropriate to the work material without compromising holder fit. Compact length and practical workshop adaptability With an overall length of 125 mm, the holder is designed for reduced overhang and improved rigidity in close‑quarters machining. The holder designation 2C-R TD and ISO identifier 1212 reflect its intended shank and head dimensions, making it straightforward to specify for toolroom lists and set‑ups. The compact footprint supports use on smaller turning centres and turret stations where space and access are limited, while the compatibility with established Taegutec indexable inserts helps integrate the holder into existing tooling families without extensive changeovers. For precise parting operations with Taegutec 2C TD inserts, contact Metav Werkzeuge for purchase support and application advice — Metav Werkzeuge is available from Emmerich to assist with selection and technical queries via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data SKU: D714TM Product name: Parting clamp holder Compatible inserts: Taegutec 2C TD Facts Overall length: 125 mm Shank dimensions: 12 x 12 mm Head width: 12 mm Cutting width: 2 mm Max parting depth: 16 mm Weight: 0.166 kg Cutting direction: right-hand Special features Holder designation ISO: 1212 Toolholder designation: 2C-R TD Suitable for indexable inserts: 2C TD Taegutec-compatible FAQ What inserts fit this parting clamp holder? The parting clamp holder is compatible with 2C TD indexable inserts and is specified for use with Taegutec 2C TD grades; the fit corresponds to the holder designation 2C-R TD (SKU D714TM). Is the cutting direction fixed or reversible? This holder is manufactured for a right-hand cutting direction and must be selected accordingly for the intended turning setup. What are the key dimensions for mounting and setup? Key dimensions are a 12 x 12 mm shank and an overall length of 125 mm, with a head width of 12 mm; these values are relevant for turret stations and toolpost clearances. What maximum parting depth can be achieved? The holder supports a maximum parting depth of 16 mm with a cutting width of 2 mm, suitable for narrow-groove and light to medium-depth parting applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Stechklemmhalter MGMN 200, 2mm Cutting Width, M4x10 Screw, T15 Hex Key, 1212, 2C MGMN 200, For MGMN 200 Inserts, Innenkühlung, Rechtsschneidend - Teknik Makina
Benefit from secure 12 x 12 mm clamping, compatibility with Korloy MGMN 200 inserts and a compact 125 mm length for space-saving setups; order via Metav Werkzeuge or contact our consultants for specification checks. Parting tool holder D010TM (MGMN 200) by Teknik Makina — 12 x 12 mm, 125 mm length A parting tool holder (MGMN 200) engineered for reliable clamping of Korloy inserts in precise parting and grooving applications across workshop turning operations. Compatible with Korloy MGMN 200 inserts 12 x 12 mm robust clamping profile Max parting depth 12 mm Includes M4x10 clamping screw, T15 key Consistent clamping for repeatable parting quality The parting tool holder D010TM delivers a stable clamping platform through its 12 x 12 mm profile, ensuring repeatable results on short-run and series production. The 12.2 mm cutting-head width and the narrow 2 mm cutting edge support fine parting operations with minimal deflection. Where process stability is essential, the combination of compact geometry and low mass (0.13 kg) reduces vibration and helps maintain surface finish quality and dimensional control. Easy integration and fast setup in the machine tool With a total length of 125 mm and an overall height of 12 mm, the holder fits compact tool posts and is suited to tight turret positions. The clamping is secured with an M4x10 hex screw driven by a T15 key, providing a straightforward and fast insert change routine that supports uptime. Compatibility with the 2C MGMN 200 configuration and Korloy MGMN inserts simplifies inventory management and reduces set-up complexity for workshops standardised on this insert family. Robust design backed by dependable supply Designed for reliable everyday use, the holder’s dimensions follow the ISO-style 1212 designation to assist in selecting matching toolholders and inserts. The lightweight construction permits rapid handling without compromising clamping stability. Sourcing through a proven distributor ensures traceable supply: Metav provides consolidated stock and a quality filter for European workshops, supporting secure delivery and consistent availability for maintenance and production replacement needs. Contact Metav Werkzeuge for tailored technical advice and reliable supply of the Teknik Makina parting tool holder D010TM; enquiries: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: D010TM Manufacturer: Teknik Makina ISO designation: 1212 Compatible inserts: Korloy MGMN 200 Bohrstangen designation: 2C MGMN 200 Dimensions & Weights Width: 12 mm Height: 12 mm Cutting head width: 12.2 mm Overall length: 125 mm Overall height: 12 mm Weight: 0.13 kg Max parting depth: 12 mm Cutting width: 2 mm Clamping screw size: M4x10 Hex key size: T15 Features & Compatibility Fits MGMN 200 insert format Compact geometry for tight turrets Low-mass design to reduce vibration Correlates with ISO 1212 tooling conventions FAQ Which insert type fits this holder? The holder accepts Korloy MGMN 200 inserts; the item is specified for the MGMN 200 insert format. What is the maximum parting depth? Maximum parting depth is 12 mm, as indicated by the holder’s stechschwert specification. What fastening hardware is supplied or required? Clamping is executed with an M4x10 screw; a T15 hex key is used to secure the insert. What are the main dimensions to check for machine compatibility? Key dimensions: 12 x 12 mm clamping profile, 125 mm overall length and 12.2 mm cutting-head width. Is the holder suitable for compact tool posts? Yes — the compact length and low overall height make it appropriate for tight turret positions and compact tool posts. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
13.5mm Boring Clamp Holder L125mm, 10mm Shank, 7.6mm Cutting Head Width - Teknik Makina
Take advantage of a compact, rigid clamping solution that combines precise dimensions and secure fastening for reliable parting and grooving operations; order the parting clamp holder directly via Metav Werkzeuge or consult our specialists for integration advice. Parting clamp holder K834TM — 13.5 mm diameter, 125 mm overall length (Teknik Makina) Parting clamp holder K834TM for fine parting and grooving tasks on turning centres and manual lathes, engineered for repeatable clamping and stable chip evacuation 13.5 mm cutting diameter 10 mm shank diameter 125 mm overall length Torx T7 screw M2.2x6 Consistent rigidity for precise parting The K834TM offers a compact form that prioritises rigidity and repeatability in short overhang set-ups. With a 10 mm shank and 125 mm overall length, the design reduces deflection during cut-off operations, improving dimensional accuracy on small parts. The relatively light weight (0.77 kg) supports quicker tool changes and lower spindle load while maintaining stability. For shops running short-cycle production, this translates into fewer reworks and a higher first-pass yield thanks to the deliberate balance between size and mass. Secure clamping and easy maintenance A focused clamping interface and the supplied fasteners ensure secure seating of the parting insert or blade. The Torx T7 drive and M2.2x6 screw specification standardise the assembly process and simplify maintenance routines, reducing set-up time per tool change. The cutting head width of 7.6 mm and a cutting height of 15 mm permit straightforward alignment in most standard toolposts, and the compact fastener arrangement keeps contamination risk low during routine cleaning. Clear torque practice and the common Torx interface support consistent clamp preload across shifts. Designed for predictable small-part production The holder’s geometry, including the 13.5 mm effective cutting diameter and a maximum parting depth of 2 mm, is tailored to short, precise cuts typical in component finishing and sample turning. The modest section width aids chip control in applications where space is limited, and the controlled parting depth provides predictable tool life when machining ductile alloys or finishing operations. Where process reliability is paramount, the compact clamp reduces the variables affecting tool engagement and repeatability. Compatibility and workshop integration Marked with the ISO shank designation S10K, the holder integrates with a wide range of toolposts and clamping systems that accept 10 mm shanks. The designation and dimensional clarity simplify toolroom planning and spare-parts management. The combination of 125 mm length and compact head dimensions makes the holder suitable for both CNC turning centres and manual lathes used in prototyping, small-batch production or repair work, enabling straightforward inventory standardisation across different machines. Contact Metav Werkzeuge today to secure Teknik Makina’s K834TM parting clamp holder for streamlined small-part parting—our specialists in Emmerich can advise on fitment and supply; eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 Technical data SKU: K834TM Product type: Parting clamp holder Label: 13.5 mm parting clamp holder L125 mm Manufacturer: Teknik Cutting Tools Dimensions & weight Diameter: 13.5 mm Shank diameter: 10 mm Overall length: 125 mm Cutting head width: 7.6 mm Cutting height: 15 mm Max parting depth: 2 mm Weight: 0.77 kg Materials & features ISO shank designation: S10K Torx key: T7 Torx screw: M2.2x6 ECLASS: 21181005 Category: Machining / Clamping holders FAQ What materials is this holder suited for? The parting clamp holder is designed for standard turning materials where a compact clamp and limited parting depth are appropriate; material-specific tool selection should match insert geometry rather than the holder itself. How is the clamp fastened and adjusted? Assembly uses a Torx T7 drive with an M2.2x6 screw; this provides repeatable clamp preload and simplifies routine maintenance. Which machines is the holder compatible with? The K834TM fits toolposts and clamping systems that accept a 10 mm shank and is suitable for both CNC turning centres and manual lathes used in small-part production. Can the holder be used for deep grooving? This holder is optimised for short parting and grooving cuts; the specified maximum parting depth of 2 mm indicates it is best for precise, shallow operations rather than deep grooving. Is the shank standardised for easy replacement? Yes—the ISO designation S10K and the 10 mm shank allow straightforward replacement and inventory alignment across compatible toolholders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
13.5mm Grooving Clamp Holder L125mm 10mm Shank 7.6mm Cutting Head Width, T7 Torx - Teknik Makina
Benefit from a compact holder that combines a 13.5 mm cutting diameter with a robust shank Ø10 mm and a 125 mm overall length for steady parting and grooving performance; order the parting toolholder directly via Metav Werkzeuge or consult our specialists for application advice. 13.5 mm parting toolholder — 125 mm overall length, Teknik Makina 13.5 mm parting toolholder designed for precise grooving and parting operations on small to medium turning centres 13.5 mm cutting diameter 125 mm overall length Shank Ø10 mm Max cutting depth 2 mm Accurate geometry for repeatable parting results The holder is engineered with a 13.5 mm nominal cutting diameter and a shank Ø10 mm, delivering a compact footprint without compromising rigidity. The design reduces radial run-out and vibration during engagement, which translates into improved dimensional repeatability and longer insert life. The shank designation S10K ensures compatibility with standard small-shank toolposts and quick, reliable clamping. Consistent cutting performance and controlled chip formation With a cutting head width of 7.6 mm and a cutting height of 15 mm, the holder provides a stable platform for narrow-parting and grooving tasks. The max cutting depth 2 mm is optimised for routine parting operations where controlled material removal is required; this depth limit helps avoid excessive tool overhang and potential chatter. The secure clamping system, fastened with the supplied M2.2x6 Torx screw (Torx key T7), maintains stable insert positioning even under intermittent loads. Compact handling for efficient setup and tooling changes At 125 mm overall length and a mass of 0.76 kg, the holder is easy to mount, balance and manoeuvre during tool setup. The compact form factor shortens set-up times on busy shopfloors and simplifies tool-store logistics. The Torx fastening system offers consistent tightening without specialised tooling; maintenance is straightforward and limited to routine inspection of the clamping screw and insert seating. Practical benefits for workshop production This parting holder is a practical choice for workshops and production lines that require a reliable, space-saving solution for grooving and light parting tasks. The compact holder minimizes tool interference in multi-tool turrets and is suitable where small-shank configurations are specified. The combination of rigid clamping, defined cutting geometry and standardised shank designation supports predictable machining cycles and lowers the frequency of unscheduled interventions. Contact Metav Werkzeuge for supply and specification matching of the Teknik Cutting Tools 13.5 mm parting toolholder (SKU K833TM) and arrange tailored advice from our consultants Technical data SKU: K833TM Label: 13.5 mm parting toolholder L125 mm Product type: Parting toolholder Manufacturer: Teknik Makina ECLASS: 21181005 Core technical data Diameter: 13.5 mm Overall length: 125 mm Weight: 0.76 kg Cutting head width: 7.6 mm Shank diameter: 10 mm Cutting height: 15 mm Max cutting depth: 2 mm Shank designation: S10K Special features Torx key required: T7 Torx screw: M2.2x6 Compact design for small-shank toolposts FAQ What is the maximum cutting depth with this holder? The maximum cutting depth is 2 mm for the parting toolholder (SKU K833TM), which is intended for controlled, narrow parting operations. Which shank diameter does the holder use? The holder is supplied with a shank Ø10 mm (S10K designation) suitable for small-shank toolposts and compact turret stations. What fastening hardware is required for insert clamping? Insert clamping uses a Torx screw M2.2x6 secured with a Torx T7 key to ensure consistent tightening and stable insert seating. Is the holder suitable for multi-tool turrets and small lathes? Yes, the compact 125 mm overall length and the small shank diameter make the holder suitable for multi-tool turrets and small to medium lathes where space is limited. Who manufactures this parting toolholder? The parting toolholder is produced by Teknik Cutting Tools and marketed under Teknik Makina specifications (SKU K833TM). Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
135mm Grooving Clamp Holder For MGM 300 Indexable Inserts 3mm Cut Width, 28mm Groove Depth - Teknik Makina
Benefit from precise compatibility with MGM 300 indexable inserts and a robust 20 mm clamping width for stable, repeatable grooving. Order the parting clamp holder directly via Metav Werkzeuge or consult their specialists for tailored technical guidance. Parting clamp holder MGM 300 L135mm — right-hand, 20 mm clamp width (Teknik Makina) The parting clamp holder is a right-hand grooving clamping solution for MGM 300 indexable inserts, designed to deliver secure parting and precision grooving on lathes and turning centres. Compatible with MGM 300 indexable inserts 135 mm overall length for deep grooving Clamp width 20 mm with robust clamping geometry Right-hand tool with max cutting depth 28 mm Maximise throughput with precise insert compatibility Designed for industrial turning applications, this holder accepts MGM 300 indexable inserts and is specified to match Korloy geometries, which means straightforward insert interchangeability and predictable cutting behaviour. The 135 mm overall length provides additional reach for deeper grooves or extended setups while maintaining rigidity. This combination reduces cycle variability and supports consistent machining results, helping production lines maintain output rates without compromising dimensional accuracy. Stable clamping for reduced vibration and longer tool life A firm clamping interface is essential for repeatability; the holder’s 20 mm clamp width and matching head dimensions create a low-deflection connection between tool and insert. The ISO 2020 clamp designation indicates standardised sizing for swift alignment, and the component’s mass (approx. 0.424 kg) contributes to damping unwanted chatter. Together, these factors result in improved surface finish and extended insert life, translating technical stability into tangible cost-efficiency for machining operations. Designed cutting geometry for controlled groove profiles The toolhead supports a maximum grooving depth of 28 mm and a cutting width of 3 mm, values that define the scope of parting and grooving tasks that can be performed in a single pass. The right-hand orientation is suited to standard lathe setups and enables predictable chip flow and tool engagement. By specifying these parameters, planners can match feeds and speeds to the holder’s capabilities, achieving reliable cuts while avoiding overloading and premature wear. Quick assembly and maintenance to keep machines running Installation is simplified with an M5x20 fastening screw and the supplied need for a 4 mm Allen key, enabling fast tool changes and secure fixation. The holder’s concise dimensions and standard fixing hardware mean minimal setup time when replacing inserts or performing routine checks. Supplied as SKU D671TM from Teknik Makina, the unit is engineered for straightforward integration into existing tool stacks, reducing downtime and supporting uninterrupted production schedules. Contact Metav Werkzeuge for expert advice and fast supply of Teknik Makina parting clamp holders compatible with MGM 300 inserts. Technical data Article number: D671TM Label: Stechklemmhalter MGM 300 L135mm Manufacturer: Teknik Makina eClass: 21181005 Dimensions & weight Overall length: 135 mm Clamp width: 20 mm Clamp height: 20 mm Cutting head width: 20 mm Max grooving depth: 28 mm Cutting width: 3 mm Weight: 0.424 kg Clamp designation ISO: 2020 Features & fittings Right-hand cutting direction Compatible insert manufacturer: Korloy Suitable for MGM 300 indexable inserts Fastening screw: M5x20 Allen key: 4 mm FAQ Which inserts are compatible with this holder? The parting clamp holder accepts MGM 300 indexable inserts and is specified to be compatible with Korloy inserts, ensuring correct seating and predictable cutting geometry. What is the maximum grooving depth for this tool? The holder supports a maximum grooving depth of 28 mm, enabling substantial single-pass cuts for many parting and grooving applications. What are the key dimensions that affect rigidity? Important dimensions are the 135 mm overall length and 20 mm clamp width; these together influence tool stiffness and vibration damping during cutting. How is the holder fastened and serviced? The holder uses an M5x20 fastening screw and requires a 4 mm Allen key for assembly and insert changes, facilitating quick maintenance and low downtime. Is this product ready for immediate integration into existing toolpost setups? Yes; delivered as SKU D671TM by Teknik Makina, the holder is designed for direct integration with standard lathe toolposts when used with MGM 300 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
140mm Stechklemmhalter 25mm Cutting Width, 4mm Blade Width, 25mm Shank Length, For MGM 4 Inserts, 4C (140-600) Bar, 2525 Clamp - Teknik Makina
Take advantage of precise, secure clamping and a compact form factor for dependable parting and grooving operations; the combination of a 4 mm cutting width and compatibility with Korloy MGM 4 inserts ensures efficient chip control and predictable tool life. Order directly via Metav Werkzeuge or consult the Metav team for integration advice. Parting tool holder D791-1TM — Right‑hand parting tool holder by Teknik Makina, 4 mm cutting width A Parting tool holder D791-1TM engineered for right‑hand parting and grooving on CNC lathes, suitable for standard insert geometries and workshop integration Right-hand parting for precision operations 4 mm cutting width for narrow grooves Compatible with Korloy MGM 4 inserts 150 mm overall length, 0.667 kg weight Faster cycle times through narrow, stable cutting The compact design with a 4 mm cutting width supports reliable chip control and reduced material waste in narrow groove and parting tasks, translating into measurable time savings on repetitive production runs. With a maximum effective cutting diameter of 600 mm, the holder addresses a wide range of turning applications while the right‑hand cutting orientation aligns with common lathe configurations. The result is an efficient, predictable process that reduces unexpected downtime and supports consistent throughput. Secure clamping for longer insert life A 25 mm cutting‑head width and a cutting height of 49 mm deliver robust seating for indexable inserts, improving clamping accuracy and vibration damping. The ISO designation 2525 and the boreshaft reference 4C (140–600) permit straightforward mounting into compatible tool posts, while the solid construction and a mass of 0.667 kg contribute to stable cutting forces. This combination lowers insert wear and reduces frequency of tool changes, contributing to lower operating costs and higher first‑pass yield. Workshop fit and practical integration An overall length of 150 mm and a shank/edge length of 25 mm make the holder simple to position in tight setups and multi‑station turrets. The unit is expressly matched to Korloy MGM 4 insert formats and offers a maximum parting blade penetration of 25 mm, enabling controlled interruption cuts and clean separation. Specifications favour quick retrofitting into existing production cells and support consistent results across serial production. For specialised setups, the clear numeric data assists in planning tool life and spindle load calculations. Contact Metav Werkzeuge for a compatibility check or assistance integrating the D791-1TM parting tool holder into the production line — Metav Werkzeuge GmbH, Emmerich; info@metav-werkzeuge.com; +49 2822 7131930 Technical data SKU: D791-1TM Manufacturer: Teknik Makina ECLASS: 21181005 Designation: Parting tool holder (translated from source) Facts Overall length: 150 mm Cutting width: 4 mm Cutting head width: 25 mm Cutting height: 49 mm Shank/edge length: 25 mm Maximum cutting diameter: 600 mm Weight: 0.667 kg Mounting bore designation: 4C (140–600) Special features ISO designation: 2525 Compatible with Korloy inserts Insert size: MGM 4 Right‑hand cutting direction Maximum parting blade penetration: 25 mm FAQ What insert type fits this holder? The holder is designed for Korloy MGM 4 style indexable inserts; the clamping geometry and seat dimensions match that insert family to ensure correct fit and repeatability. Is the cutting direction fixed? Yes, the unit is configured for right‑hand cutting operations, suitable for conventional lathe parting and grooving setups. Which shank or mounting sizes are supported? Mounting is compatible with the boreshaft designation 4C (140–600) and the ISO 2525 form factor; verify turret or toolpost bore dimensions before installation. What is the maximum effective cutting diameter? The holder supports operations up to an effective cutting diameter of 600 mm, as provided in the technical specifications. How deep can the parting blade penetrate? The maximum parting/blade penetration is 25 mm, allowing controlled separation depths for most standard turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
140mm Stechklemmhalter 4° Width, 25mm Shank Length, MGM 4 For Indexable Inserts, Left-Hand Cutting, 2525, 4C-L (140-600), Internal Cooling - Teknik Makina
Take advantage of a robust clamping system with precise 25 mm cutting-head control and compatibility with MGM 4 inserts to keep turning and grooving cycles consistent and efficient; order via Metav Werkzeuge or consult their specialists for integration advice. Stechklemmhalter D811-1TM – Parting and grooving clamping holder, left-hand, ISO 2525 by Teknik Makina A reliable Stechklemmhalter designed for left-hand parting and grooving operations on lathes, compatible with standard MGM 4-style inserts and shank designation 2525 for straightforward toolholder integration Left-hand cutting direction Compatible with Korloy MGM 4 inserts 25 mm cutting head width ISO 2525 shank designation Consistent clamping for accurate parting and grooving A secure clamp is essential when performing grooving or parting operations; the D811-1TM provides stable tool retention that reduces chatter and improves surface finish. The holder’s robust clamping mechanism keeps the insert seat rigid under cutting forces, which translates into repeatable part quality and longer insert life. For operations where consistent groove widths or clean part-offs are required, predictable tool behaviour cuts rework and increases throughput. Broad compatibility reduces tooling complexity The design accepts MGM 4 format inserts and is specified as compatible with Korloy cutting inserts, enabling simple replacement with widely available grades. Using a common insert family makes it easier to switch grades for different materials without changing the holder, lowering inventory complexity. This interchangeability supports efficient workshop logistics and faster set-ups, especially beneficial in mixed-production environments where quick tool changeovers matter. Optimised for left-hand cutting and safe machining Specified for left-hand cutting, the holder is tailored to applications that require operations from the opposite direction of standard right-hand tooling. That specification helps clarify mounting and prevents misapplication. The holder’s designation 4C-L (140-600) indicates the shank range and intended diameter adaptability, and the stated max cutting diameter 600 mm provides guidance for appropriate lathe usage. Clear directionality and defined limits reduce the risk of incorrect installation and improve operator safety. Compact dimensions that lower vibration and improve accessibility With an overall length of 150 mm, a cutting-head width of 25 mm and a narrow insert width of 4 mm, the holder keeps overhang to a minimum and helps maintain rigidity in confined setups. The modest mass (0.667 kg) further helps in dynamic balance and makes handling during tool changes straightforward. These dimensions support closer clearance to workpiece features, simplify access in tight toolposts and assist in achieving stable cutting conditions for fine grooving tasks. For tailored integration of the Teknik Makina D811-1TM into production setups and assured supply from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss suitability and order details. Technical data Article number: D811-1TM Product name: Stechklemmhalter Manufacturer: Teknik Makina Weight: 0.667 kg Core dimensions Overall length: 150 mm Shank/diameter: 140 mm Max cutting diameter: 600 mm Cutting-head width: 25 mm Insert width: 4 mm Cutting height: 49 mm Maximum parting depth: 25 mm Compatibility & features Compatible inserts: MGM 4 Suitable insert manufacturer: Korloy Shank designation: 2525 (ISO) Shank series: 4C-L (140-600) Cutting direction: left FAQ Which inserts fit this holder best? The Stechklemmhalter D811-1TM accepts MGM 4 inserts; Korloy MGM 4 grades are listed as compatible with this holder for standard grooving and parting tasks. Is the holder suitable for heavy-duty parting at large diameters? The D811-1TM is rated for a maximum cutting diameter of 600 mm; application at larger diameters should consider machine rigidity and clamping conditions. How does left-hand cutting affect mounting? Left-hand specification means the tool cuts when mounted for opposite rotational direction compared with right-hand tools; correct mounting of the D811-1TM prevents improper cutting forces and ensures safe operation. What are the key dimensions to check before ordering? Important measurements include overall length 150 mm, shank/diameter 140 mm, cutting-head width 25 mm and insert width 4 mm; these determine fit in the toolpost and compatibility with insert sizes. Which shank series is this holder compatible with? The holder uses the 4C-L (140-600) shank designation and corresponds to ISO 2525 sizing for integration into appropriate tool blocks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Boring Clamp Holder 15.5mm Cutting Width, 12mm Shank - Teknik Makina
Benefit from robust clamping and precision-guided parting thanks to the combination of a 15.5 mm nominal diameter and a 150 mm overall length, delivering stable cuts and reliable repeatability; order the tool through Metav Werkzeuge or consult our specialists for application advice. 15.5 mm parting tool holder (L150 mm) — Teknik Makina A 15.5 mm parting tool holder (L150 mm) engineered for precise parting and grooving in lathe turning setups, offering compact dimensions and secure clamping for repeatable results 15.5 mm nominal diameter 150 mm overall length 12 mm shank diameter 8.6 mm cutting head width Stable clamping to reduce vibration and improve finish A compact toolholder with a 15.5 mm nominal diameter and 12 mm shank provides the stiffness required for controlled parting operations. Increased rigidity reduces chatter, which in turn improves surface finish and extends insert life; this is particularly relevant when performing narrow cut-offs or fine grooving where vibration can spoil the component or the blade. The holder’s geometry focuses on secure blade retention and consistent alignment, so cycle-to-cycle variance is minimised and set-up time is reduced. Space-saving dimensions for tight toolpost arrangements With an overall length of 150 mm and a cutting head width of 8.6 mm, this holder is designed to fit compact toolposts and multi-tool turrets while maintaining effective chip evacuation. The 20 mm cutting height supports accurate blade positioning above the workpiece centre, reducing the need for repeated adjustments. Fast assembly is enabled by the supplied fastening hardware specification, ensuring the holder integrates smoothly into existing turning routines and workholding layouts. Practical fastenings and serviceability for the workshop The holder uses a Torx T7 drive and an M2.2x6 Torx screw for blade clamping, enabling repeatable torque application and straightforward maintenance with common workshop tools. Compatibility notes such as the S12M bar designation assist in selecting the correct complementary tooling. At only 0.13 kg, the component keeps carriage load low while still providing dependable clamp force; this balance supports productivity without compromising safety or precision. Contact Metav Werkzeuge today to request technical guidance on the Teknik Makina 15.5 mm parting tool holder (SKU K835TM) or to arrange a tailored supply and delivery via info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: K835TM Brand: Teknik Makina Product type: Parting tool holder Label: 15.5 mm Stechklemmhalter L150mm eClass: 21181005 Specifications Nominal diameter: 15.5 mm Overall length: 150 mm Shank diameter: 12 mm Cutting head width: 8.6 mm Cutting height: 20 mm Max parting depth: 2 mm Weight: 0.13 kg Features Torx key: T7 Torx screw: M2.2x6 Boring bar designation: S12M SKU: K835TM Category: Clamping holder FAQ What shank size does the holder require? The holder uses a 12 mm shank diameter, making it suitable for toolposts and adaptors that accept a 12 mm mount; the 12 mm shank contributes to the rigidity of the 15.5 mm parting tool holder (SKU K835TM). Which fastener is used to clamp the blade? Blade clamping is secured with an M2.2x6 Torx screw driven by a T7 Torx key, offering consistent clamp force and easy servicing. What is the maximum parting depth achievable? The maximum parting depth specified for this holder is 2 mm, which supports precise, shallow cut-off operations and fine grooving tasks. Is the toolholder compatible with S12M bars? Yes, the designation S12M is referenced for the boring bar compatibility and helps when matching the holder to existing bar systems and toolposts. How does the holder affect vibration and finish? The combination of a 15.5 mm nominal diameter and a 12 mm shank increases stiffness, reducing vibration and typically improving surface finish compared with less rigid setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Boring Clamp Holder for MGM 300 Indexable Inserts 3mm Cutting Width, Right-Hand - Teknik Makina
Take advantage of the rigid 25 mm clamp design and 150 mm overall length to secure consistent grooving and parting results; compatibility with MGM 300 indexable inserts from Korloy means fewer adapter changes and faster set-up. Order the holder directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Stechklemmhalter MGM 300 L150mm — Grooving clamp holder, 25 mm width (Teknik Makina) The Stechklemmhalter MGM 300 L150mm is a right-hand grooving clamp holder designed for precision parting and grooving operations using MGM 300 indexable inserts Compatible with MGM 300 inserts (Korloy) Robust 25 mm clamp width for stable cutting 150 mm overall length for deep grooves Right-hand orientation, 26 mm max cutting depth Consistent parting through a rigid, compact design The holder's 25 mm clamp width and solid construction deliver repeatable clamping force, reducing vibration and improving surface finish during parting operations. By maintaining a firm engagement with the insert, the toolholder supports predictable tool life and lowers scrap rates. The 0.735 kg mass and compact footprint help to keep tool overhang manageable, contributing to better runout control and more reliable cycle times on lathes and turn-mill centres. Fast integration with established insert systems Built for MGM 300 indexable inserts, the toolholder accepts Korloy inserts without further adaptation, cutting setup complexity and inventory variety. The standard M6x20 clamping screw and supplied 5 mm Allen key enable quick insert changes and straightforward torque application. This direct compatibility minimises downtime between jobs and simplifies logistics for workshops that already stock MGM 300 tooling. Designed for productive, industrial use With an overall length of 150 mm and a maximum cutting diameter capability up to 600 mm, the holder suits both bench-level repairs and full-scale production turning. The 26 mm maximum cutting depth permits efficient grooving in deeper sections while the 3 mm cutting width specification supports fine, precise parting tasks. Materials commonly machined with this type of holder include steels and alloyed materials where controlled chip evacuation and stable clamping are required. Practical handling and setup benefits The right-hand orientation and clearly defined cutting head dimensions — 25 mm head width and 40 mm cutting height — simplify tool selection and mounting. The compact design reduces the need for extensive countermeasures against chatter, while the standardised screw and key sizes ensure maintenance and exchange procedures remain consistent across the workshop. These practical advantages translate into lower set-up times and improved throughput for repeating operations. Contact Metav Werkzeuge for tailored advice on application suitability, or request assistance in selecting compatible inserts and accessories — Metav Werkzeuge delivers from Emmerich with reliable stock and fast processing. Technical Data Article number: D785-1TM SKU: D785-1TM Product type: Stechklemmhalter Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.735 kg Clamp width: 25 mm Head width: 25 mm Cutting height: 40 mm Max cutting diameter: 600 mm Max cutting depth: 26 mm Cutting width: 3 mm Orientation: right Special features Suitable for: MGM 300 indexable inserts Compatible insert manufacturer: Korloy Clamping screw: M6x20 Allen key: 5 mm FAQ What inserts fit this holder? The holder accepts MGM 300 indexable inserts, and it is routinely used with Korloy inserts for immediate fitment and optimal performance. Is the holder suitable for deep grooving operations? Yes. With a 150 mm overall length and 26 mm maximum cutting depth, the clamp is designed for deeper grooving and parting tasks in standard turning operations. Which screw and tool are needed for insert clamping? Insert clamping is achieved with an M6x20 clamping screw and a 5 mm Allen key, which are the standard fixing sizes for secure, repeatable set-up. Can the holder be used on large-diameter workpieces? The holder is specified for cutting diameters up to 600 mm, making it suitable for medium to large workpieces within that range. What is the SKU and who manufactures the product? The SKU is D785-1TM; the manufacturer is Teknik Makina, and the item is supplied through Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Boring Clamp Holder Left 3mm Cutting Width 18mm Max Depth, ISO 2525 - Teknik Makina
Benefit from a secure left-hand orientation, a compact 150 mm overall length and a 25 x 25 mm clamping cross-section for repeatable parting and grooving operations — order the parting tool holder directly via Metav Werkzeuge or consult our specialists for an application check. Parting tool holder D887TM — left-hand, 150 mm overall length by Teknik Makina A Parting tool holder D887TM engineered for reliable left-hand parting and grooving, featuring a 25 x 25 mm shank and ISO clamping for straightforward machine mounting. Robust 25 x 25 mm cross-section Left-hand orientation for parting cuts 3 mm cutting width for narrow grooves ISO 2525 clamping interface Secure clamping for consistent parting results The holder is built around a 25 x 25 mm cross-section and the ISO 2525 clamping interface, giving a stable connection to the tool post or turret. This stability reduces vibration and improves insert life, which in turn lowers cycle-to-cycle variation. Tightening uses an M6x20 clamping screw with a 5 mm Allen key requirement, ensuring a compact but firm fastening that supports predictable groove geometry during production. Compact geometry that improves access and rigidity With an overall length of 150 mm and a mass of 0.735 kg, the design balances reach and stiffness for close-in parting operations. The relatively short span minimises overhang and helps maintain cutting line accuracy, making it suitable where rigidity is essential. The 3 mm nominal cutting width supports narrow-separation tasks while the tool’s geometry keeps deflection to a minimum, improving repeatability and reducing scrap rates. Fast setup and predictable orientation on the lathe The left-hand orientation is ideal for applications that require cuts entering from the workpiece centre towards the chuck. The holder’s interface and fastening arrangement simplify seating of the tool and changeover of inserts, shortening setup time. Because the design follows established mounting standards, the holder integrates with common toolposts and turrets, aiding quick alignment and reducing machine downtime during tool changes. Designed for workshop durability and dependable delivery Manufactured by Teknik Makina, the component is intended for routine shop-floor use where robust clamping and concise parting depth are required. The specified maximum plunge depth of 18 mm supports many standard grooving tasks without compromising rigidity. Backed by Metav’s European distribution and quality-filtering in Emmerich, the solution pairs manufacturing-grade hardware with dependable logistics for continuous production. For Teknik Makina quality and dependable delivery from Metav Werkzeuge, request a personalised application recommendation or product supply — Metav Werkzeuge supplies directly from Emmerich and can advise on integration into existing turning setups Technical data Article number: D887TM Manufacturer: Teknik Makina Label: Stechklemmhalter L150mm Product type: Parting tool holder eClass: 21181005 Core technical data Overall length: 150 mm Weight: 0.735 kg Clamping width: 25 mm Clamping height: 25 mm Cutting head width: 25 mm Cutting width: 3 mm Maximum plunging depth: 18 mm Clamping screw: M6x20 Allen key size: 5 mm Cutting direction: left Special features ISO 2525 clamping interface Left-hand cutting orientation M6x20 clamping screw Allen key size specification: 5 mm FAQ Which cutting direction does the holder support? The parting tool holder D887TM is configured for a left-hand cutting direction and is intended for parting cuts from the workpiece centre towards the chuck. What is the maximum parting depth? The D887TM offers a maximum plunging depth of 18 mm for parting and grooving tasks. Which clamping interface is used for mounting? Mounting follows the ISO 2525 clamping specification, ensuring compatibility with standard toolposts and turrets that accept this interface. What are the key dimensions to check for machine compatibility? Relevant dimensions are a 150 mm overall length and a 25 x 25 mm shank cross-section; these determine reach and the required tool-holder pocket. Which fastening hardware does the tool use? Fastening is secured with an M6x20 clamping screw and requires a 5 mm Allen key for tightening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Boring Insert Holder 3mm Cutting Width, 22mm Max Depth, Left-Handed, 2525 3C-L DGN For 3C DGN Inserts, Internal Coolant - Teknik Makina
Take advantage of the combination of precise left-hand grooving, a narrow 3 mm cutting width and secure ISO compatibility for consistent parting and reduced setup time; order the D733TM directly via Metav Werkzeuge or ask the consultants if needed. Teknik Makina Stechklemmhalter D733TM — Left-hand grooving holder, 3 mm cut width The D733TM grooving holder for turning bars, designed for left-hand parting and compatible with 3C DGN inserts Left-hand grooving holder, narrow 3 mm cutting width ISO 2525 clamping designation Compatible with 3C DGN inserts (ISCAR) 25 mm height, 150 mm overall length Consistent left-hand grooving for repeatable parting The left-hand design delivers controlled cutting forces when parting or grooving from the left side, reducing tool chatter and improving surface finish on turned components. With a defined 3 mm cutting width and a maximum plunge depth of 22 mm, the holder is suited to narrow slotting and parting operations where dimensional accuracy is required. The geometry of a purpose-made grooving holder concentrates cutting loads near the insert, which supports repeatable results and longer cycle reliability in batch production. Stable clamping and compact dimensions for rigid setups A compact cross-section—25 mm height, 25 mm width and a 25 mm cutting-head width—combined with a 150 mm overall length provides a balance between reach and rigidity. The holder’s mass (approx. 0.711 kg) and ISO designation 2525 indicate a standardised mounting interface that promotes secure installation and reduced runout. Standardised shank and clamping interfaces help maintain concentricity when fitted to compatible bars, translating into fewer rejects and less rework during high-volume turning tasks. Insert compatibility and workflow advantages Designed for use with 3C DGN inserts from ISCAR, the holder accepts proven insert grades and geometries, enabling quick index changes and reduced downtime. Using replaceable indexable inserts keeps tool inventory flexible: one holder can service multiple cutting tasks by swapping inserts rather than replacing the whole tool. The bar reference 3C-L DGN denotes the mating shank type, simplifying procurement and ensuring a proper mechanical fit on established tool posts. Practical benefits for workshop efficiency The D733TM’s focused functionality reduces the need for trial-and-error setups. The combination of a narrow cut width and standardised clamping means fewer tool variations are necessary across similar jobs, lowering storage complexity and speeding changeovers. For operations that run left-hand parting regularly, the investment in a dedicated holder yields measurable improvements in cycle stability and process repeatability, especially in series production. For process-reliable left-hand grooving choose Teknik Makina’s D733TM — contact Metav Werkzeuge for tailored advice and prompt supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D733TM Manufacturer: Teknik Makina Product name: Stechklemmhalter D733TM Direction of cut: left Facts Holder height: 25 mm Holder width: 25 mm Cutting-head width: 25 mm Cutting width: 3 mm Max plunge depth: 22 mm Overall length: 150 mm Weight: 0.711 kg ISO designation: 2525 Bar designation: 3C-L DGN Special features Compatible inserts: 3C DGN Suitable insert manufacturer: ISCAR Left-hand grooving holder Designed for narrow-slot and parting operations FAQ Which inserts fit this grooving holder? The D733TM is specified for 3C DGN inserts and is commonly used with grades supplied by ISCAR for grooving and parting tasks. Is the holder suitable for deep plunging operations? With a maximum plunge depth of 22 mm, the holder is intended for standard grooving and parting depths rather than heavy deep-cut plunge applications. What does the ISO 2525 designation mean for mounting? ISO 2525 indicates a standard clamping and interface form; this helps ensure the holder mounts securely and is interchangeable with tool bars that conform to the same standard. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Clamping Holder 11 ER For Indexable Inserts, Right-Hand Cutting, Innenkühlung SER 1212 M11-ER11 - Teknik Makina
Take advantage of the combination of precise clamping, compact dimensions and quick assembly for consistent external-threading results in batch and single-part production. Order the component directly via Metav Werkzeuge or contact our consultants for specification checks. SER 1212 clamping holder (D498TM) – right-hand external threading, compact 12 × 12 mm cross-section The SER 1212 clamping holder is a right-hand tool holder designed for external threading on lathes and turning centres, providing a compact, rigid solution for short overhang and repeatable thread profiles. SER 1212 clamping holder for external threads Right-hand cutting direction Compatible with ER11 inserts and M11-ER11 shank Compact 12 × 12 mm cross-section Precision and stability for repeatable thread quality The compact 12 × 12 mm cross-section and a cutting height of 20 mm deliver a rigid seating that minimises vibration during turning, which improves surface finish and thread accuracy. The tool body design keeps the insert firmly clamped, translating into consistent thread form across production runs. This rigidity is especially relevant where repeatability matters, such as batch threading of shafts or pins, because reduced chatter leads to fewer rejects and less rework. Fast setup and secure clamping reduce downtime Compatibility with standard ER11 turning inserts and the M11-ER11 shank designation means the holder integrates cleanly with common boring-bar systems. Assembly relies on a Torx fixing (key T8) and a securing screw (M2.5×5.5), allowing fast, repeatable changeovers with minimal adjustment. The ISO designation SER 1212 signals an established form factor that fits industry workflows, so tool change procedures remain lean and reliable in a production environment. Compact overall length and light handling for flexible use With an overall length of 150 mm and a net weight of 0.193 kg, the holder balances accessibility and control: long enough for typical setups but short enough to keep overhang low for improved rigidity. The right-hand cutting direction supports conventional thread turning operations without altering feed strategy. Designed by Teknik Makina, this tool holder suits both demanding shop-floor use and smaller workshops seeking industrial‑grade clamping performance with compact dimensions. Contact Metav Werkzeuge today to discuss the Teknik Makina SER 1212 clamping holder and confirm suitability for specific threading tasks or to arrange prompt delivery from our Emmerich hub. Technical data Article number: D498TM Manufacturer: Teknik Makina ISO designation: SER 1212 Description: clamping holder for outside thread, right-hand Facts Cross-section width: 12 mm Cross-section height: 12 mm Cutting height: 20 mm Overall length: 150 mm Weight: 0.193 kg Special features Right-hand cutting direction For turning inserts: 11 ER Boring bar / shank designation: M11-ER11 Torx screw: M2.5×5.5 Torx key size: T8 SKU: D498TM FAQ What cutting direction is this holder designed for? The SER 1212 clamping holder is configured for a right-hand cutting direction suitable for standard external-thread turning operations. Which inserts and shank standards are supported? This tool supports 11 ER turning inserts and corresponds to a M11-ER11 shank/boring-bar designation for straightforward integration. What are the key dimensions and weight of the holder? The holder has a 12 × 12 mm cross-section, 20 mm cutting height, overall length 150 mm and weighs 0.193 kg. Which fastening hardware is used for the clamping screw? The clamping screw is M2.5×5.5, tightened with a T8 Torx key for quick, repeatable assembly. Is this holder suitable for production environments? Yes; the SER 1212 clamping holder (Teknik Makina, SKU D498TM) offers compact rigidity and standard interface compatibility, making it suitable for consistent threading across production batches. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fast, reliable parting and grooving for precision turning
Parting and grooving tools, also referred to as parting blades, grooving tools or cut-off tools, are narrow carrier tools for lathes fitted with replaceable carbide inserts. Supplied as solid holders or flat blades, they are designed to cut precise grooves and to part finished components cleanly from the material bar.
Why internal coolant matters for deep cuts and tough materials
When used in simple form without internal coolant, the cutting fluid is applied via external machine nozzles; this is often sufficient for very shallow grooves and easily machinable materials. For deeper grooving and parting operations, however, the tool nearly encloses the slot so that external coolant cannot reach the cutting edge. Tools with internal coolant incorporate fine, integrated channels that deliver coolant under high pressure directly to the insert and beneath the chip. This targeted supply controls the intense heat in the confined cutting zone and uses flushing pressure to eject chips reliably, preventing chip jamming, surface damage and sudden tool breakage.
Clear operational benefits you can measure
- faster cycle times through reliable chip evacuation and uninterrupted cutting
- extended tool life thanks to effective heat control at the cutting edge
- consistent surface finish by avoiding chip re-cutting and scarring
- safer machining of hard or ductile materials due to reduced risk of tool fracture
- simplified setup when holders with integrated channels replace complex external coolant rigs
Metav as a practical partner for your workshop
Metav stands for democratisation of precision: decades of expertise, a quality filter in Emmerich and an assortment that supports industry and trade. With more than 48,000 customers and a catalogue of over 250,000 products, Metav provides a focused selection of parting and grooving tools, accessories and matched holders so that procurement and technical choice remain straightforward and dependable.
Parting and grooving tools bring reliable groove geometry and safe parting to turning operations; choosing holders with integrated coolant channels is essential for deep cuts and demanding materials. If technical advice is needed, Metav’s product specialists can help select the appropriate tool geometry and coolant configuration for the application.
FAQ
When is internal coolant necessary for parting tools?
Internal coolant becomes necessary for deep grooving and parting or when machining hard or ductile materials; it delivers coolant directly to the insert and beneath the chip, which is critical when external nozzles can no longer reach the cutting edge.
Can parting tools be used without internal coolant?
Yes — for very shallow cuts and easily machinable materials, parting tools can be used with external machine coolant nozzles, but performance and tool life will drop markedly for deeper cuts.
How do parting tools prevent dangerous chip jamming?
Parting tools with integrated channels use high-pressure coolant to flush chips out of the narrow slot, preventing chips from becoming trapped and minimising the risk of surface damage and abrupt tool failure.
What should be considered when choosing a grooving insert and holder?
Select a combination that matches the required groove depth and material grade; holders offering integrated high-pressure channels are preferred for deep cuts or poor-chip-breaking materials to ensure heat control and reliable chip evacuation.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com