Robust HSS twist drill for daily workshop use
HSS twist drill DIN 338 type N short roll-forged black 118° is designed for reliable, high-performance drilling in components up to about 900 N/mm², delivering clean holes in alloyed and unalloyed steels, castings, sintered metals, non-ferrous metals and plastics; its high-speed steel construction and short roll-forged design increase fracture resistance and stability while the black surface reduces friction and wear. The tool is ideal for hand and pillar drills and for small series production where precise, repeatable results are required, combining good chip evacuation with consistent cutting geometry. Key benefits include enhanced tool life, improved hole quality and greater operational stability thanks to the combination of HSS material, 118° conical point, and short roll-forged shank.
4.7mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS Twist Drill, 4.7 mm, 118° point angle, Black, DIN 338 The Twist Drill Type N short HSS is a precision metalworking tool designed for stable, accurate drilling in alloyed and unalloyed metals with hand and drilling machines. Short design for improved stability HSS material for durable metal machining 118° point for fast penetration in softer metals DIN 338 compliant for standardised quality Suitable for Hand and Drilling Machines Precise metal drilling with measurable benefits Designed for demanding metalworking tasks, the short Type N Twist Drill offers a clear advantage in stability and accuracy. Because the short flute length reduces overhang, the tool shows less deflection during operation, which results in more concentric holes and less rework. The HSS material (High Speed Steel) ensures toughness and wear resistance when drilling alloyed and unalloyed steels, cast iron, non‑ferrous metals and plastics. One direct benefit is fewer rejects and predictable results on production runs where repeatability matters. Built for stability and easy handling The compact geometry and DIN 338 conformity make this short twist drill especially suitable where rigidity is essential. A shortened overall length minimises bending moments, so the bit remains stable even under higher cutting forces. Use in a properly secured chuck on a Hand or Drilling Machine yields cleaner hole edges and reduces chatter, which helps to achieve better surface finish and longer tool life. For workshop environments prioritising precision, the compact design is a practical improvement over longer alternatives. Simple explanation of key technical features The 118° point angle balances centring ability and cutting efficiency: a slightly sharper tip eases entry into softer metals and Aluminium, while still performing well in general steel applications. The designation Type N denotes the normal spiral geometry suited to general metal drilling — not optimised for extremely soft timber or specialised masonry. This short HSS variant can be roll‑rolled or ground according to DIN specifications; roll‑rolled versions often show improved ductility and reduced breaking risk for small diameters under 6 mm. Who benefits and how to apply this tool Professional tradespeople and precision workshops that require repeatable, reliable holes in metal benefit most from this short HSS Twist Drill. When accurate hole position and reduced runout are priorities, the shorter length gives tangible process advantages. Start drilling at moderate speed with appropriate cutting fluid for steel work to extend tool life; reduce feed if you experience excessive vibration. For applications demanding higher wear resistance or use on very hard stainless steels, consider alternative geometries or coatings. Trusted recommendation: Opt for the MetavCUT Twist Drill Type N short HSS for robust, precise metal drilling — for expert advice and application support contact METAV Werkzeuge via info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40047-FDA Diameter: 4.7 mm Spiral Length: 47 mm Overall Length: 80 mm Point Angle: 118° Type: Type N Execution: short Material: HSS (High Speed Steel) Standard: DIN 338 Colour: Black Application: Drills for Metal For: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Twist Drill Type N be used on stainless steel? The MetavCUT Twist Drill Type N is suitable for many steels, including alloyed and unalloyed varieties, but for very hard stainless steels performance may be limited; in such cases a drill with a larger point angle, special coating or different grade is recommended to avoid premature wear and to maintain hole quality. For what are Twist Drills used? A Twist Drill by MetavCUT Type N is mainly applied to the machining of high‑strength materials and larger hole diameters; this form is easy to regrind and withstands higher loads, making it well suited for demanding metal drilling operations. Which 3 drill types exist? Commonly distinguished drill types are Metal Drill, Wood Drill and Stone/Concrete Drill; the MetavCUT Twist Drill falls into the Metal Drill category and is optimised for metalworking tasks.
4.8mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Der kurze HSS-Bohrer vereint Stabilität durch reduzierte Auskraglänge und hohe Bruchsicherheit bei kleinen Durchmessern; dadurch entfällt bei vielen Metallarbeiten unnötiges Nacharbeiten. Nutzen Sie die Kombination aus HSS-Material und normgerechter Bauart (DIN 338) für präzise Ergebnisse in Werkstatt und Produktion. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer von MetavCUT — kurzer HSS-Bohrer (Typ N, 4,8 mm) Der Spiralbohrer ist ein kurzer HSS-Bohrer für präzises Bohren in Metall an Handbohrmaschinen und stationären Bohrmaschinen. Kurz: hohe Stabilität durch geringe Auskraglänge HSS: elastisch und bruchärmer bei kleinen Durchmessern Gemäß DIN 338: kurze Spiralbohrer Spitzenwinkel 118° für einfache Anbohrung Ideal für Handbohrmaschine und Metallarbeiten HSS-Konstruktion für weniger Bruch und längere Standzeit Aus HSS gefertigt, bietet der Bohrer eine höhere Elastizität und reduziert dadurch das Bruchrisiko bei Durchmessern unter 6 mm. Die kurze Ausführung nach DIN 338 sorgt für eine verminderte Auskraglänge, was die Stabilität erhöht und Vibrationen beim Bohren in Stahl und Gusseisen reduziert. Für Anwender bedeutet das weniger Nacharbeit und längere Einsatzintervalle, ohne dass die Handhabung schwieriger wird. Die schwarze Oberfläche schützt zusätzlich vor Korrosion und erleichtert die Identifikation in der Werkstatt. Präzise Anwendung bei Metall: Vorteile und Tipps Die Typ N-Spiralform ist auf Metallbearbeitung ausgelegt und eignet sich für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle sowie Kunststoffe. Der Spitzenwinkel von 118° ermöglicht ein einfaches Anbohren und gute Zentrierung auf flachen Oberflächen; bei besonders harten Werkstoffen empfiehlt sich ein größerer Winkel. Um die Lebensdauer zu maximieren, sollten Schnittgeschwindigkeit und Kühlschmierstoff an Material und Durchmesser angepasst werden. Durch die kurze Bauform reduziert sich die Gefahr des Verkippens bei Handbetrieb. Einsatzempfehlung für Werkstatt und Montage Mit einem Durchmesser von 4,8 mm fällt der Bohrer in den Standard-Bereich für universelle Werkstatteinsätze. Er ist ideal für Reparaturarbeiten, Maschinenmontage und DIY-Projekte, bei denen Handbohrmaschinen zum Einsatz kommen. Für präzise Bohrbilder empfiehlt sich vorheriges Anpunkten mit einem Zentrierbohrer, um Wandern auf der Oberfläche zu vermeiden. Die Spirallänge von 47 mm und die Gesamtlänge von 86 mm bieten eine ausgewogene Balance zwischen Reichweite und Steifigkeit. Verpackung, Zielgruppe und Qualitätsversprechen Der Spiralbohrer kommt gebündelt in einer Verpackungseinheit zu 10 Stück und richtet sich an Profiwerkstätten sowie anspruchsvolle Heimwerker, die Wert auf zuverlässige Standardwerkzeuge legen. Hersteller MetavCUT steht für eine technikorientierte Fertigung und gleichbleibende Qualität, passend zur Philosophie von Metav Werkzeuge als Lieferant für präzise Werkstattausstattung. Die kompakte Bauform und die Normkonformität machen den Bohrer zur wirtschaftlichen Wahl für Serien- wie Einzelaufgaben. Für präzises Metallbohren die MetavCUT HSS-Ausführung wählen und direkt bei Metav Werkzeuge anfragen: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Technische Daten Artikelnummer: 40048-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Typ: Typ N Fakten Durchmesser: 4,8 mm Gesamtlänge: 86 mm Spirallänge: 47 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS (Schnellarbeitsstahl) Norm: DIN 338 (kurze Spiralbohrer) Ausführung: kurz Farbe: schwarz Für Bohrmaschine: Handbohrmaschine FAQ Wie eignet sich der Bohrer für Stahlbleche? Der MetavCUT Spiralbohrer (Typ N, SKU 40048-FDA) ist für dünne bis mittlere Stahlbleche geeignet; durch das HSS-Material reduziert sich das Bruchrisiko und das kurze Design erhöht die Stabilität beim Bohren. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, die Ausführung wurde ausdrücklich für den Einsatz an Handbohrmaschinen und stationären Maschinen konzipiert und liefert bei korrekter Anwendung zuverlässige Ergebnisse. Welche Materialien lassen sich mit diesem Bohrer bearbeiten? Der Bohrer von MetavCUT bearbeitet legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle sowie Kunststoff; für sehr harte Werkstoffe ist ein speziellerer Bohrer empfehlenswert. Warum ist die kurze Ausführung nach DIN 338 vorteilhaft? Die kurze Bauform verringert die Auskraglänge, was die Stabilität erhöht und das Risiko von Verbiegen oder Vibrationen beim Bohren reduziert. Wie viele Bohrer sind in der Verpackungseinheit enthalten? Geliefert wird eine Verpackungseinheit mit 10 Spiralbohrern, ideal für Werkstattbedarf und Reparatursets.
4.9mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill Type N (HSS, 4.9 mm, 118° tip, short, black, DIN 338) by MetavCUT The Twist Drill is a short Type N metal drill designed for precise holemaking in steel and other metals when used with a hand drill or drilling machine. Short HSS design for high stability DIN 338 compliant for consistent quality 118° tip angle for reliable centring Type N spiral optimised for Metal drilling Suitable for Hand Drills and Drilling Machines Greater Precision and Less Deflection for Metalworking Short, roll-formed HSS construction and the compact geometry deliver improved stiffness compared with longer bits, so holes stay true even under side loads. Users benefit from reduced runout and better positional accuracy when working on steel, cast iron or non-ferrous Metal, because the shorter overhang minimises vibration and bending. This makes the bit particularly suitable for demanding workshop tasks where consistent hole diameter and alignment matter. Tip Geometry That Eases Start and Keeps Centre A 118° tip angle provides a balanced compromise between fast penetration and secure centring on curved or mildly uneven surfaces. The reduced querschneide resulting from careful pointing lowers friction during entry, so less feed force is required and the bit centres more reliably. For operators with limited setup aids, this tip geometry simplifies starting the hole and reduces the chance of walking on sheet or slightly convex workpieces. Robust Material and Easy Reconditioning Manufactured from High Speed Steel (HSS), the bit combines toughness with the possibility of economical resharpening. HSS offers elasticity that reduces fracture risk in diameters below typical thresholds and is appropriate for alloyed and unalloyed steel as well as many non-ferrous materials and plastics. Regular sharpening restores cutting edges efficiently, extending service life while keeping performance consistent for repetitive tasks. Tailored for Workshop and Maintenance Use This short Type N spiral is specified under DIN 338, which defines short twist drills with cylindrical shank for metalworking. The configuration is aimed at professionals and skilled hobbyists who need a reliable everyday metal drill for general maintenance, fitting or fabrication work. Because of its sturdy design, the bit is well suited to both stationary and portable drilling where stability and repeatable results are priorities. Strong recommendation: choose the MetavCUT Twist Drill Type N for precise metal drilling — for application advice or additional technical data please contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40049-FDA Durchmesser: 4.9 mm Spirallänge: 52 mm Gesamtlänge: 86 mm Material: HSS (High Speed Steel) Spitzenwinkel: 118° Norm: DIN 338 Typ: Type N Ausführung: short Für Bohrmaschine: Drilling Machine / Hand Drill Farbe: black Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and where does the MetavCUT Twist Drill Type N excel? The MetavCUT Twist Drill Type N is primarily used for drilling in high-strength materials and larger diameters; it excels at penetrating steel, cast iron and non-ferrous metals. Its short design gives greater stability and precision, and the HSS material allows economical resharpening while maintaining toughness under standard workshop conditions. Which three drill types exist? The main drill categories are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill falls into the metal drill category and is optimised for reliable performance in metalworking applications.
4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 4 mm, 118°, black, DIN 338, HSS (MetavCUT) The Twist Drill is a short HSS Type N metal drill designed for precise drilling with hand drills and drilling machines in metalworking applications. Short design for enhanced stability and precision HSS material for elasticity and reduced breakage risk Conforms to DIN 338 for short twist drills 118° tip angle for reliable centring in softer metals Suitable for hand drill and drilling machine use Efficient performance through material and geometry This short HSS bit combines material properties and geometry to deliver reliable results when drilling metal. High Speed Steel provides elasticity that reduces the risk of breakage, particularly in small diameters below 6 mm, while the short overall length minimises deflection and vibration. One clear benefit is improved tool life during repetitive production tasks thanks to the balanced combination of material toughness and stable design. Stability and precision for demanding metalwork Conforming to DIN 338, the bit’s reduced overhang increases rigidity and enables more precise hole placement in demanding operations. The Type N normal spiral flute is optimised for machining steel, cast iron and non-ferrous metals, giving consistent chip evacuation and rounder holes. Users who require repeatable accuracy in component manufacture will notice less wobble and fewer rejects when using a short configuration. Practical suitability for common drills and applications Designed for use with a hand drill or drilling machine, the 4 mm diameter and 118° tip angle make this bit versatile for general metalworking and softer materials where reliable centring is beneficial. The short flute length improves control when working on thin sheets or small fixtures. This configuration supports technicians who need a dependable tool for maintenance, prototyping and workshop tasks without sacrificing handling comfort. Clear explanation of technical terms and user guidance The designation Type N refers to the standard spiral geometry for metal drills, offering a compromise between cutting action and chip removal; HSS stands for High Speed Steel, a material suited to many common machining tasks. The 118° tip angle means the point is sharper than a 135° variant, which helps with initial bite and centring on curved or coated surfaces. For users unfamiliar with DIN 338, it simply specifies dimensions and tolerances for short straight-shank twist drills so compatibility and performance are predictable. Strong recommendation: For dependable metal drilling, choose the MetavCUT short HSS Twist Drill for its stability and material properties — METAV Werkzeuge offers expert advice to ensure the right tool choice for each application; contact them by email at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp at +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 40040-FDA Diameter: 4 mm Tip angle: 118° Spiral length: 43 mm Overall length: 75 mm Execution: short Type: Type N For drill: Hand drill / Drilling Machine Colour: black Material: HSS (High Speed Steel) Standard: DIN 338 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT used for? The MetavCUT Twist Drill is primarily used for machining high-strength materials and larger drill diameters in metalworking; its form allows straightforward resharpening and it withstands greater loads, making it suitable for workshop and industrial drilling tasks. Which three drill types are there? The main categories are metal drills, wood drills and stone/concrete drills, and the MetavCUT Twist Drill belongs to the metal drill group designed for machining metals with appropriate cutting geometries.
5.1mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Als Kombination aus Stabilität und Präzision überzeugt dieser Kurzbohrer durch Haltbarkeit und sichere Handhabung bei Metallbohrungen; nutzen Sie die HSS-Legierung und die DIN-338-Norm für verlässliche Ergebnisse, und wenden Sie sich bei Fragen an Metav als kompetenten Anbieter aus Emmerich. Spiralbohrer von MetavCUT, HSS kurz Der Spiralbohrer von MetavCUT für präzise Metallbohrungen in Handbohrmaschine und stationären Maschinen HSS-Ausführung für legierten und unlegierten Stahl Kurzbauform nach DIN 338 für erhöhte Stabilität 5,1 mm Durchmesser für Standard-Anwendungen Spitzenwinkel 118° für sauberes Anbohren Zylinderschaft für Handbohrmaschine und Spannfutter Haltbarkeit und Werkstoffvorteile für langlebige Ergebnisse Haltbarkeit ist bei Bohrern ein entscheidendes Merkmal. HSS (Schnellarbeitsstahl) sorgt für gute Elastizität und reduziert das Bruchrisiko insbesondere bei kleinen Durchmessern. Die Fertigungsweise als rollgewalzter Kurzspiralbohrer führt zu einer homogenen Werkstoffstruktur und damit zu höherer Zähigkeit. Anwendungen an legiertem und unlegiertem Stahl, Gusseisen sowie Nichteisenmetallen werden dadurch zuverlässig abgedeckt. Die Einhaltung der DIN 338 gewährleistet, dass Länge, Geometrie und Abmessungen normgerecht sind und die Kompatibilität mit Standardspannfuttern sichergestellt bleibt. Präzision und empfohlene Einsatzweise für saubere Bohrbilder Präzision entsteht durch Stabilität und korrekte Anwendung. Typ N mit Normalspirale eignet sich besonders für Metallbohrungen und liefert saubere Spanabfuhr. Bei einem Durchmesser von 5,1 mm empfiehlt sich Voranbohren oder Anpunktieren für höchste Passgenauigkeit bei dünnen Blechen und Profilen. Für die Standzeit ist eine kühle Schneide wichtig; daher Kühlmittel oder geringe Schnittkräfte nutzen, um Überhitzung zu vermeiden. Die Kurz-Ausführung minimiert Auslenkung, wodurch exaktere Bohrbilder und engerer Rundlauf erreicht werden. Handhabung, Sicherheit und Hinweise zur Maschinenwahl Handhabung ist einfach und sicher, wenn die richtige Maschine gewählt wird. Zylinderschaft und Gesamtlänge von 86 mm bei einer Spirallänge von 52 mm ermöglichen festen Sitz im Spannfutter und geringe Durchbiegung. Bei Einsatz in Handbohrmaschine auf gleichmäßige Führung achten und Drehzahl sowie Vorschub an Material anpassen; für Stahl höhere Drehzahlen und moderater Vorschub empfehlen. Tiefe Bohrungen über das Fünffache des Durchmessers vermeiden, da die Spanabfuhr und Kühlung sonst eingeschränkt sind. Die Kurz-Version reduziert Bruchrisiko und ist daher besonders für Werkstatt- und Montagearbeiten geeignet. Zielgruppe und typische Einsatzbereiche mit klarem Nutzen Zielgruppe sind Werkstätten, Montagebetriebe und anspruchsvolle Heimwerker, die robuste und normgerechte Werkzeuge benötigen. Einsatzbereiche reichen von allgemeinen Metallbauarbeiten über Maschineninstandsetzung bis zu präzisen Montagearbeiten an Blechen und Profilen. Die kompakte Ausführung bietet einen praktischen Vorteil: geringere Werkzeugschwingung führt zu saubereren Bohrungen und weniger Nacharbeit. MetavCUT stellt dabei die Verbindung aus technischer Verlässlichkeit und logistischer Sicherheit her, damit die Werkbank jederzeit einsatzbereit bleibt. Empfehlung: Setzen Sie auf den Kurz-Spiralbohrer von MetavCUT in HSS für präzise Metallbohrungen und kontaktieren Sie Metav bei Fragen per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 40051-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Zahlen Durchmesser: 5,1 mm Gesamtlänge: 86 mm Spirallänge: 52 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS (Schnellarbeitsstahl) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Typ: Typ N (Normalspirale) Ausführung: kurz Farbe: schwarz Für Bohrmaschine: Handbohrmaschine SKU: 40051-FDA FAQ Für welche Materialien eignet sich dieser Spiralbohrer am besten? Der Spiralbohrer von MetavCUT in HSS eignet sich besonders für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; bei harten Werkstoffen auf angepasste Schnittwerte achten. Ist die Kurz-Ausführung nach DIN 338 kompatibel mit üblichen Spannfuttern? Ja, die Kurz-Ausführung entspricht der DIN 338 und ist für gängige Spannfutter von Handbohrmaschinen und stationären Bohrmaschinen ausgelegt. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das für die Anwendung? Der Bohrer hat einen Spitzenwinkel von 118°, was das Anbohren erleichtert und saubere Einläufe in weichere bis mittlere Metalle ermöglicht; für sehr harte Werkstoffe kann ein größerer Winkel sinnvoll sein. Wie tief darf mit dem 5,1 mm Bohrer sicher gebohrt werden? Bei einem Durchmesser von 5,1 mm gilt als Praxisregel, tiefe Löcher über das fünffache des Durchmessers zu vermeiden; für tiefere Bohrungen schrittweise aufbohren oder längere Spiralbohrer verwenden. Welche Pflege verlängert die Standzeit des HSS-Spiralbohrers? Regelmäßige Kühlung bei Metallbearbeitung, saubere Spanabfuhr und sachgemäße Lagerung sind wirksame Maßnahmen zur Verlängerung der Standzeit des HSS-Bohrers von MetavCUT.
5.2mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill Type N — 5.2 mm, 118° tip, short HSS, DIN 338, black (MetavCUT) The Twist Drill Type N (short) is a compact HSS drill designed for precise metal drilling in Drilling Machines and Hand Drills. Short HSS design for high stability Conforms to DIN 338 for short twist drills 118° tip for reliable centring on metals 5.2 mm diameter for standard metalwork Black finish for clear visual contrast in use Durable HSS Construction for Reliable Metalworking The short HSS construction delivers a balance of elasticity and wear resistance ideal for routine metal drilling. Manufactured in accordance with DIN 338, this short twist drill offers a reduced overhang that increases rigidity and minimises bending under load. The result is consistent hole quality and longer tool life when drilling alloyed and unalloyed steels, cast iron, non-ferrous metals and plastics. Users benefit from fewer rejects and less tool breakage during standard operations. Precision Tip Geometry That Improves Start and Centring A 118° tip angle provides better initial penetration and easier centring on slightly curved or uneven surfaces, which is especially useful for softer metals and general workshop tasks. The Type N “normal spiral” geometry is the classical choice for metal drilling, offering predictable chip removal and straightforward resharpening. This tip geometry reduces walking at the drill entry and supports cleaner, more accurate holes with minimal rework required. Compact Short Design for Stability and Accuracy With a reduced overall length and a spiral length optimised for stability, this short Twist Drill minimises deflection during use and is therefore suited to jobs requiring precision. The shorter configuration makes it particularly appropriate for bench work and applications where the drill protrudes only slightly from the chuck, improving concentricity and surface finish. Operators will notice steadier feeds and a lower risk of drill bending when working with diameters in the mid range. Practical Usage and Target Applications Designed primarily as a Drill for Metal, the Twist Drill Type N from MetavCUT is aimed at tradespeople, machinists and workshops that perform general metal fabrication and repair. Its roll-formed HSS manufacturing makes it especially suitable for drilling holes under 6 mm in a variety of metallic materials, while still being serviceable on non-ferrous materials and plastics. The black finish provides a clear visual contrast for alignment and handling during repetitive tasks. Care, Sharpening and Compatibility Notes This short HSS Twist Drill is straightforward to resharpen and maintain; its geometry allows conventional grinding without complex special tooling. For optimal results, use appropriate cutting lubrication and moderate feed rates to reduce heat build-up. When precision is critical, a rigid chuck and minimal overhang are recommended to preserve concentricity and hole quality. For larger diameters or deeper holes, consider drills specifically sized for those tasks to avoid undue stress on the tool. Strongly recommended: Choose the MetavCUT short HSS Twist Drill Type N for dependable, precise metal drilling — METAV Werkzeuge offers expert technical advice and support via eMail info@metav-werkzeuge.com, Phone +49 2822 7131930 and WhatsApp +49 170 2837271 Technical Information Designation: Twist Drill Marke: MetavCUT SKU: 40052-FDA Diameter: 5.2 mm Tip Angle: 118° Type: Type N Execution: short Material: HSS Colour: black Spiral Length: 52 mm Overall Length: 86 mm Application: Drills for metal Standard: DIN 338 Suitable For: Drilling Machine / Hand Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N best used for? The MetavCUT Twist Drill Type N is primarily intended for metalworking applications; it is used for drilling alloyed and unalloyed steels, cast iron, non-ferrous metals and plastics, providing reliable performance in routine workshop tasks. Can the MetavCUT Twist Drill Type N be used in a hand drill? Yes, the MetavCUT Twist Drill Type N in its short execution is suitable for use in both Drilling Machines and Hand Drills, offering increased stability due to its reduced overhang. What are Twist Drills used for? Twist Drills are mainly applied when machining high-strength materials and for larger hole diameters; their form is easily ground and they withstand higher loads. Which three drill types exist? There are Metal Drills, Wood Drills and Stone/Concrete Drills. Why are Twist Drills sharpened at the tip? The tip sharpening reduces the cross cutting edge at the point of the twist drill, which significantly lowers friction forces and therefore reduces feed forces while improving centring in the workpiece. Can a Twist Drill be used to drill wood? A Metal Drill such as the MetavCUT Twist Drill can also be used in wood, but it offers less precise guidance and a less clean finish; it is easier to resharpen and shows less self-feeding action. For which drilling depths is the Twist Drill most commonly used? A through-hole is often executed with a Twist Drill; for diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The general assumption that HSSE steels are always superior to standard HSS steels is incorrect; evaluate whether the specific working conditions justify the higher initial cost of HSSE before deciding.
5.3mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Kompakte Kurz-Ausführung mit hoher Stabilität und elastischem HSS-Werkstoff sowie genormter DIN 338-Qualität für präzise Metallbohrungen; ideal für handgeführte und stationäre Anwendungen. Bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere technische Beratung bei Bedarf an. Spiralbohrer von MetavCUT, kurz, HSS, Typ N Der Spiralbohrer in Kurz-Ausführung eignet sich für präzise Metallbohrungen an Handbohrmaschine und stationären Maschinen und kombiniert Stabilität mit geringer Bruchneigung. HSS-Schnellarbeitsstahl für elastische Belastung DIN 338 konforme kurze Spiralbohrer-Ausführung Kurz-Ausführung für erhöhte Stabilität beim Bohren Typ N Normalspirale, ideal für Metall und Stahl Geeignet für Handbohrmaschine und stationäre Maschinen Höhere Stabilität durch kurze Ausführung Die Kurz-Ausführung reduziert die Auskraglänge und minimiert dadurch das Verbiegen beim Bohren, was zu gleichmäßigen Bohrbildern und längerer Standzeit führt. Für Anwendungen in Stahl, Gusseisen und Nichteisenmetallen sorgt die geringere Hebelwirkung für sichere Bohrvorgänge. Diese Bauform ermöglicht besonders in beengten Arbeitsbereichen präzise Ergebnisse ohne übermäßige Schwingungen. Elastischer HSS-Materialvorteil für geringes Bruchrisiko Der aus HSS gefertigte Bohrer bietet aufgrund der rollgewalzten Herstellung eine erhöhte Elastizität, die das Bruchrisiko insbesondere bei Durchmessern unter 6 mm vermindert. Dies ist bei Serienreparaturen und Einzelanwendungen vorteilhaft, weil weniger Ausschuss entsteht und Nacharbeit reduziert wird. HSS steht für Schnellarbeitsstahl und erlaubt hohe Schnittgeschwindigkeiten bei Metallbearbeitung. Normierte Ausführung für verlässliche Einsetzbarkeit Die Einhaltung der DIN 338 garantiert, dass Abmessungen, Schaftform und Toleranzen reproduzierbar sind und sich der Bohrer problemlos in gängigen Spannfuttern und Maschinen einsetzen lässt. Anwender profitieren von Austauschbarkeit, planbarer Werkzeugauslegung und kompatiblen Ersatzteilen. Die Norm sorgt zudem für klare Vorgaben bei Auswahl und Lagerhaltung in Werkstätten. Spitze und Geometrie für sauberes Anbohren Der 118° Spitzenwinkel unterstützt das Zentrieren auf unterschiedlichen Metalloberflächen und beschleunigt den Antritt in weicheren Materialien, ohne die Eignung für härtere Werkstoffe einzuschränken. In Kombination mit der Normalspirale Typ N entsteht eine ausgewogene Spanabfuhr, die bei mittleren Bohrtiefen zuverlässig arbeitet und die Oberfläche der Bohrung schützt. Zielgruppe und typische Anwendungsszenarien Dieser Kurz-Spiralbohrer ist konzipiert für Werkstätten, Monteure und ambitionierte Heimwerker, die präzise Metallbohrungen mit Handbohrmaschine oder stationärer Maschine durchführen. Einsatzgebiete sind Montagearbeiten, Instandhaltung und allgemeiner Maschinenbau, bei denen Stabilität und Normkonformität im Vordergrund stehen. Kaufen Sie den MetavCUT Spiralbohrer in Kurz-Ausführung mit HSS für zuverlässige Metallbohrungen und kontaktieren Sie unsere technische Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 für Bestell- und Anwendungsfragen Produktmerkmale Artikelnummer: 40053-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Typ: Typ N Norm: DIN 338 Ausführung: kurz Daten Durchmesser: 5,3 mm Gesamtlänge: 86 mm Spirallänge: 52 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS (Schnellarbeitsstahl, elastisch) Farbe: schwarz Für Bohrmaschine: Handbohrmaschine DIN 338: Norm für kurze Spiralbohrer FAQ Ist der MetavCUT Spiralbohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer in HSS-Ausführung und Typ N eignet sich für viele Edelstähle, bei härteren Legierungen sind angepasste Schnittdaten und Kühlung empfehlenswert, um Standzeit und Qualität der Bohrung zu erhalten. Welche Spannfuttergröße passt für den 5,3 mm Bohrer? Für den 5,3 mm MetavCUT Spiralbohrer wird ein Standardspannfutter im entsprechenden Bereich verwendet; die zylindrische Schaftform nach DIN 338 ermöglicht einfache Aufnahme in handelsüblichen Bohrfuttern. Warum ist die Kurz-Ausführung vorteilhaft für Montagearbeiten? Die Kurz-Ausführung des MetavCUT Spiralbohrers reduziert Schwingungen und erhöht die Stabilität beim Bohren, was besonders in beengten Montageumgebungen zu saubereren Bohrbildern und weniger Werkzeugbruch führt. Wie viele Bohrer sind in einer Verpackungseinheit? Die Verpackungseinheit enthält 10 Stück des MetavCUT Spiralbohrers, Artikelnummer 40053-FDA, ideal für Werkstattbedarf und Vorratshaltung. Welchen Spitzenwinkel sollte ich bei härterem Material wählen? Der gelieferten MetavCUT Spiralbohrer hat einen Spitzenwinkel von 118°; für sehr harte Materialien kann ein 135° Spitzenwinkel sinnvoll sein, bei Standardarbeiten liefert 118° jedoch gutes Antrittsverhalten und Zentrierung.
5.4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS Ø 5.4 mm, 118° tip, Black (DIN 338) by MetavCUT A short Twist Drill Type N for precise metal drilling in a Drilling Machine, designed for stable performance and clean holemaking. Short HSS design for improved stability Conforms to DIN 338 for short twist drills 5.4 mm Diameter for accurate hole tolerances 118° Tip angle for reliable centring Optimised for Drilling Machine operation High precision and efficient metal cutting for workshop use The Twist Drill in HSS construction delivers consistent cutting performance when working with alloyed and unalloyed steels, cast iron and non-ferrous metals. Its Type N normal spiral and short configuration reduce overhang and vibration, which increases rigidity and improves hole accuracy. The 118° tip angle facilitates easier entry and dependable centring on flat and slightly curved surfaces, so drilling cycles become more predictable and tool life is extended. This combination of geometry and material yields reliable results on demanding metal tasks. Stable handling and suitability for machine or hand operation Designed for use in a Drilling Machine or comparable hand-operated equipment, this short Twist Drill offers improved stability during feed and reaming operations. The reduced overall length lowers the tendency to deflect, allowing operators to maintain tighter tolerances with less scrap. Its black finish aids in visual inspection of wear, while the compact form factor supports confined working conditions. If guidance is needed for selecting the right twist drill for a specific application, METAV Werkzeuge provides expert consultation to match tool choice and machining parameters to the task. Standards, material properties and application recommendations Manufactured in accordance with DIN 338, this short HSS tool follows established tolerances and dimensional classes for cylinder-shank short twist drills. HSS (High Speed Steel) offers an elastic microstructure that reduces breakage risk when drilling holes below 6 mm diameter and performs well across a range of common workshop materials. The Type N spiral is a classic metal-drilling geometry; when combined with the short design it is particularly suited to precision holes in steel and similar alloys. For deeper or larger-diameter drilling tasks, consider using specialised long or coated variants tailored to the material and depth requirements. METAVCUT’s Twist Drill is recommended for demanding metalworking tasks — for tailored advice or further technical data contact METAV Werkzeuge at info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill (Type N), short, Ø 5.4 mm, overall length 93 mm, spiral length 52 mm, 118° tip angle, HSS, black, for Drilling Machine, DIN 338 Brand: MetavCUT SKU: 40054-FDA Diameter: 5.4 mm Spiral length: 52 mm Overall length: 93 mm Tip angle: 118° Material: HSS (High Speed Steel) Type: Type N (normal spiral) Execution: short Standard: DIN 338 Colour: black Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is the Twist Drill used? The MetavCUT Twist Drill Type N is primarily applied to the machining of high-strength materials and larger drill diameters; its form is easy to regrind and withstands higher stresses, making it suitable for robust metalworking tasks. Which three drill types exist? Three common categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the Metal drill group and is optimised for those applications. Why are Twist Drills pointed? The tip is honed to reduce the cross-cut at the point of the Twist Drill, which lowers friction and therefore reduces required feed forces while improving centring accuracy in the workpiece. Can you drill wood with a metal Twist Drill? A metal Twist Drill such as the MetavCUT Type N can be used in wood, but guidance and finish are inferior compared with dedicated wood drills; however, they are easier to regrind and exhibit lower self-feed tendencies. At what drilling depths is the Twist Drill most used? For through-hole drilling up to about 20 mm diameter and depths up to 100 mm, the Twist Drill is the most commonly used tool for producing cylindrical holes by material removal. What is better, HSS or HSSE? The general belief that HSSE steels are always superior to HSS is not correct; when choosing between HSS and HSSE for a MetavCUT Twist Drill, assess whether the specific working conditions justify the higher cost of HSSE.
5.5mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill (Type N) — HSS Short Twist Drill, 5.5 mm, 118°, DIN 338, Black, for Drilling Machine, MetavCUT The Twist Drill (Type N) is a short HSS metal drill engineered for stable, precise holemaking in metal on handheld and benchtop drilling machines. Short HSS design for increased stability 5.5 mm diameter for precise holemaking 118° tip for reliable centring Conforms to DIN 338 for consistent quality Optimised for use with Drilling Machine High-performance HSS body for reliable metalworking The HSS composition of this Twist Drill provides a balanced combination of elasticity and wear resistance suitable for standard metalworking tasks. Manufactured to deliver predictable cutting behaviour, the HSS material reduces the risk of brittle fracture when drilling holes below 6 mm diameter and supports clean machining in both alloyed and unalloyed steels. This material choice results in a tool that is easier to resharpen and that maintains edge integrity during routine workshop use Precise centring and efficient cut formation with 118° tip A 118° tip angle promotes good initial centring and controlled chip formation when working with softer metals and common engineering steels. The Type N normal spiral geometry ensures consistent chip evacuation and reduced tendency to wander on curved or slightly uneven surfaces. For applications that demand accurate positioning, this tip geometry lowers the required feed force and supports more repeatable hole locations on finished parts Short execution for greater stability and accuracy The short overall design reduces overhang and increases rigidity, which directly improves hole quality on both portable and stationary drilling equipment. Conforming to DIN 338, the short configuration minimises deflection and vibration, making the tool particularly suitable for precision operations and for use in fixtures or jigs. This stabilising effect is a key benefit when working with small diameters where accuracy and roundness matter most Designed for metalworkers and general workshop use Intended primarily as a Drill for Metal, this short HSS twist drill is aimed at technicians, maintenance staff and machinists seeking a dependable everyday tool. The Type N spiral is the classic choice for general metal drilling and fits well into common work routines, from prototype fabrication to repair tasks. When application-specific guidance is needed, METAV Werkzeuge offers competent technical consultation to ensure the right tool choice for the job For reliable metal drilling with a focus on stability and repeatable results, choose the MetavCUT Twist Drill Type N and contact METAV Werkzeuge for personalised technical advice — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40055-FDA Diameter: 5.5 mm Tip angle: 118° Spiral length: 52 mm Overall length: 93 mm Material: HSS Type: Type N Execution: short Colour: black Application: Drills for metal For drilling machine: Drilling Machine Norm: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill primarily used for? The MetavCUT Twist Drill (Type N) is primarily used for the machining of high-strength materials and for larger drill diameters in metalworking. This design is easy to resharpen and remains stable under higher loads, which makes it suitable for demanding metal-drilling tasks. Which three drill types are commonly distinguished? When selecting tools, the common classification comprises Metal Drills, Wood Drills and Stone/Concrete Drills. The MetavCUT Twist Drill (Type N) belongs to the Metal Drills group and is optimised for drilling in metals. Why are Twist Drills pointed? The point sharpening reduces the cross-cut at the tip of the Twist Drill, which markedly lowers friction and therefore reduces the required feed forces. In addition, the sharpened tip improves centring of the tool in the workpiece, helping to achieve cleaner and more accurate holes when using the MetavCUT Twist Drill (Type N). Can a Twist Drill be used in wood? A Metal Drill such as the MetavCUT Twist Drill (Type N) can be used in wood, but guidance and finish quality are inferior compared with dedicated wood drills. Metal drills have less guidance and produce a less clean hole, though they are easier to resharpen and exhibit lower self-feed tendencies.
5.6mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill Type N — HSS short, Ø 5.6 mm, 118° tip, black, DIN 338, short execution The Twist Drill Type N is a short HSS metal drill engineered for precision drilling in metal with a 5.6 mm diameter and a 118° tip suitable for drilling machines and hand drills. Short HSS design for increased stability Conforms to DIN 338 for short twist drills 118° tip for improved centring in metal 5.6 mm diameter for standard hole sizes Precision and stable performance for metalworking The Twist Drill from MetavCUT delivers reproducible results when working with metal thanks to its HSS composition and short geometry. The reduced overhang improves Stability and reduces vibration during cutting, which leads to cleaner Holes and less tool deflection. For metalworking applications where accuracy matters, the short design offers higher rigidity than longer drills and helps maintain concentricity even under varying feed conditions. Material and norm advantages for reliable use Manufactured in HSS, this short Type N drill is aligned with DIN 338, which defines short twist drills with cylindrical shank for metalworking. The 118° Tip provides a balance between fast penetration and good centring on slightly softer Metals and general Steel grades. The roll-formed or ground production options described by the norm ensure consistent geometry and simplify resharpening when required, supporting long-term usability and predictable drilling behaviour. Intended applications and who benefits most Designed primarily as a metalworking tool, the Type N geometry suits workshops, maintenance teams and professionals who use drilling machines or hand drills for steel, cast Iron and non-ferrous Metals. Its 5.6 mm diameter makes it appropriate for typical assembly and fabrication tasks where precision holes are required. Users seeking a robust, easy-to-handle drill for repetitive metal drilling will value the combination of short length and HSS material for a lower risk of breakage on small-diameter holes. Handling, sharpening and practical notes The shorter overall length reduces chatter and supports accurate axial guidance; this makes the drill easier to control in portable and stationary machines. When sharpening the point, preserving the 118° geometry maintains the intended cutting behaviour: reduced thrust and improved centring. For the best results, apply suitable cutting fluid and moderate feeds when drilling harder alloys to extend tool life. Regular inspection of the cutting lips will indicate when resharpening is needed to restore performance. We strongly recommend the MetavCUT Twist Drill Type N for precision metalworking — for personalised technical advice or to confirm suitability contact METAV Werkzeuge by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Twist Drill Marke: MetavCUT SKU: 40056-FDA Durchmesser: 5,6 mm Spitzenwinkel: 118° Spirallänge: 57 mm Gesamtlänge: 93 mm Typ: Type N Ausführung: short Farbe: black Material: HSS Norm: DIN 338 Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N used for? The MetavCUT Twist Drill Type N is primarily used for metalworking tasks; as a short HSS drill it is suitable for drilling in alloyed and unalloyed Steel, Cast Iron and various Non-Ferrous Metals where stability and precision are required. Can the MetavCUT Twist Drill Type N be used in a hand drill? Yes, the MetavCUT Twist Drill Type N is compatible with drilling machines and can be used in many Hand Drill applications, though the short design is particularly advantageous in stationary setups or where minimal overhang is needed. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high-strength materials and larger drill diameters; this shape is relatively easy to resharpen and withstands higher loads during drilling. Which three drill types exist? There are three common drill categories: Metal drill, Wood drill, and Stone/Concrete drill. Why are Twist Drills sharpened? Sharpening reduces the cross-cutting edge at the Tip of the Twist Drill, which lowers friction forces and therefore reduces the required feed force while improving centring in the Workpiece. Can you drill wood with a Twist Drill? A Metal Twist Drill can be used in Wood, but it offers poorer guidance and a less clean finish compared with dedicated Wood drills; however, such drills are simpler to resharpen and exhibit lower self-feeding tendencies. At which drilling depths is the Twist Drill most used? A full through-hole is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The common belief that HSSE steels are categorically superior to standard HSS is not universally true; evaluate whether the specific working conditions justify the higher purchase cost of HSSE before choosing.
5.75mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill (Type N) – HSS short, 5.75 mm, 118° tip, black, DIN 338 The Twist Drill Type N is a short HSS drill bit designed for metalworking, offering precise 5.75 mm holes with a 118° tip for reliable centring in handheld and machine drilling applications. Short HSS design for increased stability 5.75 mm diameter for precise metal holes 118° tip for reliable centring on curved surfaces Conforms to DIN 338 for short twist drills Type N spiral optimized for metal drilling Precision and durability for metalworking tasks This Twist Drill is manufactured from HSS (High Speed Steel) to deliver consistent cutting performance in metalworking. The short execution and firm geometry reduce deflection and vibration, which improves hole accuracy and prolongs tool life compared with longer variants. The 5.75 mm nominal diameter and classic Type N spiral make this bit particularly suitable for drilling unalloyed and alloyed steels, cast iron and various non-ferrous metals. The DIN 338 designation confirms the design as a short spiral drill with a cylindrical shank, intended for use in both stationary machines and portable drilling machines. Stability and handling advantages of the short design A reduced overhang from the chuck yields measurable benefits in everyday workshop use: the shorter flute length (57 mm) and overall length (93 mm) improve centring and reduce walking at the start of the hole, while increasing rigidity during plunge. For operations where precision is critical, such as aligning multiple holes or working on small assemblies, the compact geometry of this Type N bit helps achieve repeatable results. The black finish provides visual contrast for quick size identification and handling in busy toolboxes. Suitable applications and target users MetavCUT’s Twist Drill is aimed at professional machinists, maintenance technicians and skilled hobbyists who require dependable performance on metal. It is intended for through-holes and general drilling tasks in metal components, and is suitable for use with handheld drilling machines as well as bench and column drills. Because the bit follows the DIN 338 standard for short drills, it is a practical choice when higher stability and positional accuracy are priorities over deep drilling. How the geometry and point angle affect performance The 118° tip angle is a versatile compromise that eases initial centring and reduces walking on slightly curved or soft surfaces, while maintaining effective cutting for many metal types. Point geometry determines how the bit enters the material: by shaping the tip to the appropriate angle and relief, cutting forces and friction are reduced, which lowers feed requirements and improves centring. Short HSS bits of the Type N family can be resharpened with conventional tools and are robust under standard workshop conditions. Choose MetavCUT’s Twist Drill for precise, stable metal drilling and contact METAV Werkzeuge for tailored technical advice — Email: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Brand / Manufacturer: MetavCUT SKU: 400575-FDA Diameter: 5.75 mm Tip Angle: 118° Type: Type N Material: HSS (High Speed Steel) Execution: Short Colour: black Spiral Length: 57 mm Overall Length: 93 mm Application: Drills for Metal Standard: DIN 338 Suitable For: Drilling Machine / Hand Drill Packaging Unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily employed for machining high-strength materials and larger drill diameters; its design is easy to regrind and withstands greater loads, making it suitable for through-holes and demanding metal-drilling tasks. Which three drill types are there? The three main drill types are metal drill bits, wood drill bits and stone/concrete drill bits; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for cutting steel and similar materials.
5.7mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Hohen Stabilität und präzise Ergebnisführung bietet diese kurze Ausführung dank HSS-Werkstoff, DIN 338-Norm und dem 5,7 mm Durchmesser; ideal für Metallbohrungen mit Handbohrmaschine. Bestellen Sie den Bohrer direkt über Metav oder lassen Sie sich von unserer technischen Beratung unterstützen. Spiralbohrer 40057-FDA von MetavCUT — kurzer HSS-Bohrer für Metall Der Spiralbohrer 40057-FDA ist ein kurzer HSS-Bohrer (Typ N) mit 5,7 mm Durchmesser, konzipiert für präzise Metallbohrungen an Handbohrmaschinen. Kurze Ausführung nach DIN 338 HSS-Material reduziert Bruchrisiko bei <6 mm Geeignet für Handbohrmaschine Spitzenwinkel 118° für sauberen Anbohrvorgang Verpackungseinheit: 10 Stück Stabilität und Präzision für anspruchsvolle Metallbohrungen Die kurze Ausführung dieses Bohrers reduziert die Auskraglänge und erhöht damit die Stabilität beim Bohren in Metall. Durch den Einsatz von HSS (Schnellarbeitsstahl) bleiben die Schneiden elastisch, was besonders bei Durchmessern unter 6 mm das Bruchrisiko mindert. In Kombination mit der Norm DIN 338 steht die Bauart für konsistente Abmessungen und zuverlässige Einsetzbarkeit an stationären und handgeführten Maschinen. Materialtechnik und Spitzengeometrie sorgen für saubere Löcher Der Bohrer nutzt die typische Geometrie der Typ N Normalspirale, die speziell für Metall ausgelegt ist. Der Spitzenwinkel 118° ermöglicht ein leichtes Anbohren und saubere Spanbildung in Baustahl, Gusseisen, Nichteisenmetallen und Kunststoffen. Für Anwender mit geringer Maschinenpräzision empfiehlt sich ein Anpunkten oder Zentrieren vor dem Bohren, um ein „Wandern“ des Bohrers zu vermeiden und die Bohrbildqualität zu sichern. Praxisnahe Anwendungsempfehlungen für die Werkstatt Für den Einsatz mit Handbohrmaschine ist der Spiralbohrer 40057-FDA optimal abgestimmt: der Durchmesser von 5,7 mm fällt in den Standard-Bereich und erlaubt direktes Bohren bei mittleren Werkstoffen. Kühlung oder Schmierstoff kann bei zähen Legierungen die Standzeit erhöhen und die Spanabfuhr verbessern. Bei anspruchsvollen Werkstücken empfiehlt sich Leichtdruck und hohe Drehzahl, um thermische Überlastung zu vermeiden. Zielgruppe und Einsatzszenarien Dieser Bohrer richtet sich an Werkstattbetreiber, Monteure und ambitionierte Heimwerker, die häufig Metall bearbeiten. Die kurze Bauform unterstützt präzises Arbeiten an Flachmaterial und Profilen, die Verpackungseinheit von 10 Stück macht die Beladung von Vorratsschränken wirtschaftlich attraktiv. MetavCUT positioniert das Werkzeug als robuste, zuverlässige Lösung für den Alltag in Industrie und Handwerk. Empfehlung: Für dauerhaft präzise Metallbohrungen die Wahl des HSS-kurzbohrers von MetavCUT treffen und bei technischen Fragen unsere Beratung kontaktieren: info@metav-werkzeuge.com • Tel. +49 2822 7131930 • WhatsApp +49 170 2837271 Produktmerkmale Artikelnummer: 40057-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Material: HSS Norm: DIN 338 Typ: Typ N Ausführung: kurz Farbe: schwarz Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Fakten Durchmesser: 5,7 mm Gesamtlänge: 93 mm Spirallänge: 57 mm Spitzenwinkel: 118° Besonderheiten HSS: Schnellarbeitsstahl, elastisch, bruchreduziert DIN 338: kurze Spiralbohrer mit Zylinderschaft (Norm) Typ N: Normalspirale, ausgelegt für Metallbearbeitung FAQ Ist der Bohrer für Edelstahl geeignet? Der Spiralbohrer 40057-FDA von MetavCUT (HSS, Typ N) eignet sich für viele Stahlarten; bei rostfreien, harten Werkstoffen empfiehlt sich langsame Schnittgeschwindigkeit und geeignete Kühlung. Kann ich den Bohrer in einer Handbohrmaschine verwenden? Ja, der kurze HSS-Bohrer wurde für die Nutzung an Handbohrmaschinen ausgelegt und bietet durch die reduzierte Auskraglänge erhöhte Stabilität beim Bohren. Welche Vorteile bietet die DIN 338-Ausführung? Die DIN 338-Ausführung garantiert normierte Längen und Schaftmaße, was die Austauschbarkeit und Einsatzsicherheit in Bohrfuttern erleichtert. Wie viele Bohrungen sind pro Bohrer zu erwarten? Die Standzeit hängt vom Werkstoff und der Kühlung ab; der HSS-Werkstoff des Spiralbohrers 40057-FDA bietet gegenüber geschwächten Varianten bessere Bruchfestigkeit bei kleinen Durchmessern. Wird der Bohrer als Einzelstück oder im Set geliefert? Der Spiralbohrer 40057-FDA wird in einer Verpackungseinheit von 10 Stück ausgeliefert, ideal für den Werkstattbedarf oder die Serienarbeit.
5.8mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
MetavCUT Twist Drill — Type N, short HSS, 5.8 mm, 118°, black, DIN 338 A MetavCUT Twist Drill Type N for precise metalworking with hand and drilling machines. Short design for enhanced stability HSS material for reliable metal drilling DIN 338 standard for short twist drills 118° point angle for easier centring Precision 5.8 mm diameter for accurate holes Stable, precise metal drilling for demanding tasks The HSS construction of this short Twist Drill ensures high hardness and good toughness for machining a wide range of metals. Thanks to the reduced free length, the short design minimises runout and bending, which improves stability during drilling and reduces the risk of breakage on small diameters. This makes the tool particularly suited to workshop use where repeatable, accurate holes are required. Engineered geometry for faster centring and cleaner holes A 118° point angle provides easier centring and controlled cutting when working on softer and medium-hard materials; the geometry reduces wandering on curved surfaces and speeds initial penetration. The 5.8 mm diameter combined with a spiral length of 57 mm and overall length 93 mm delivers a compact tool that is easy to position in a chuck or hand drill. The Type N normal spiral is optimised for metal, offering good chip evacuation and long tool life in standard drilling applications. Designed for professionals and hobbyists, with expert support This Twist Drill is aimed at machinists, maintenance technicians and hobbyists who need a robust metal-drilling solution in portable or bench drilling machines. Manufactured by MetavCUT, it follows DIN 338 for short twist drills and is ideal when rigidity and precision are priorities. If uncertain whether this drill matches a specific application, METAV Werkzeuge provides comprehensive, competent advice to help select the right tool and parameters. Strong recommendation: Choose the MetavCUT Twist Drill Type N for reliable, precise metal drilling and contact METAV Werkzeuge for personalised technical support — Email: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 40058-FDA Type: Type N Diameter: 5.8 mm Point angle: 118° Material: HSS Execution: short Colour: black Spiral length: 57 mm Overall length: 93 mm For: Drilling Machine / Hand Drills Application: Drills for metal Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is designed for machining high-strength and common engineering steels as well as non-ferrous metals. Its short HSS design offers increased stability and makes it suitable for demanding drilling tasks and larger diameters, while remaining easy to regrind when needed. Which three drill types exist? The main drill types are Metal drills, Wood drills, and Stone/Concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for those materials, offering geometry and material choices suited to metalworking.
5.9mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 5.9 mm, HSS, Short, Black, 118° (DIN 338) by MetavCUT The Twist Drill is a short HSS Type N metalworking drill designed for precise drilling in Drilling Machines and Hand Drills across workshop and maintenance applications. Short HSS design for increased stability DIN 338 compliant for consistent quality 118° Tip for reliable centring Suited for Drilling Machine and Hand Drill Black finish for improved corrosion resistance Precision and Stability for Metalworking Manufactured as a short variant according to DIN 338, this Twist Drill offers enhanced stability and minimal deflection during machining. Because the protruding length is reduced, the tool runs truer in the chuck and transfers cutting forces more directly, resulting in straighter holes and longer tool life. This design is particularly beneficial when working with tougher materials where chatter and bending would normally compromise accuracy. Tip Geometry Optimised for Reliable Centring The 118° Tip provides a balanced compromise between fast penetration and good centring, making it well suited for softer steels, non-ferrous metals and general metalworking tasks. A narrower tip angle reduces the tendency to wander on curved or uneven surfaces, while the point geometry also lowers the initial radial forces so that drilling starts cleanly and precisely. This results in more accurate hole positioning and less rework. High Speed Steel Construction for Durable Performance Made from HSS (High Speed Steel), the drill combines toughness with wear resistance for typical metal drilling tasks. The roll-formed production method increases elasticity and reduces breakage risk in smaller diameters, while still allowing reliable performance in alloyed and unalloyed steels, cast iron, non-ferrous metals and selected plastics. Users benefit from a tool that tolerates machining stresses and can be resharpened when necessary, prolonging service life. Designed for Professional and Workshop Use This Twist Drill supports both stationary Drilling Machines and portable Hand Drills, providing versatility for tradespeople and maintenance technicians. The black surface finish helps to delay corrosion and eases chip evacuation, while the Type N normal spiral geometry focuses on efficient metal cutting. For demanding tasks where stability and repeatable results matter, this tool delivers consistent performance. Choose MetavCUT quality for confident metalworking — for personalised technical advice contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or reach out via WhatsApp +49 170 2837271 Technical Details Bezeichnung: Twist Drill (Spiralbohrer) Marke: MetavCUT SKU: 40059-FDA Typ: Type N Durchmesser: 5.9 mm Spitzenwinkel: 118° Material: HSS Norm: DIN 338 Ausführung: Short Spiral Length: 57 mm Overall Length: 93 mm Colour: Black Application: Drills for metal Recommended For: Drilling Machine / Hand Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials is it suited to? The MetavCUT Twist Drill (Type N) is primarily applied to metalworking; it is used especially for machining tougher materials and larger drill diameters where tool stability is essential. Its HSS construction allows effective drilling in alloyed and unalloyed steel, cast iron, non-ferrous metals and some plastics. Which three drill types are commonly available? The three main drill categories are Metal Drill, Wood Drill and Stone/Concrete Drill; the MetavCUT Twist Drill is classified as a Metal Drill suited to machining metals. Why are Twist Drills pointed? The point reduces the size of the cross-cutting edge at the tip. Pointing the Twist Drill significantly lowers friction and therefore the required feed force, while improving the drill tip’s ability to self-centre in the workpiece for cleaner starts. Can the Twist Drill be used to drill wood? A Metal Drill such as the MetavCUT Twist Drill can be used in wood, but it will typically have less guidance and produce a rougher finish than a dedicated Wood Drill. Metal drills are easier to resharpen and show less self-feeding, which can be an advantage or disadvantage depending on the task. At which drilling depths is the Twist Drill most commonly used? A through-hole in solid material is often executed with a Twist Drill. For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool.
5mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, Diameter 5 mm, 118° Point Angle, HSS, Short, Black, DIN 338, MetavCUT The Twist Drill Type N is a short HSS metal drill designed for precise drilling in metal using hand or drilling machines. Short Design for high stability Conforms to DIN 338 for consistent dimensions HSS material for elastic toughness on small diameters 118° Point Angle for reliable centring in softer metals Suitable for hand and drilling machines Greater accuracy through a short, stable design A short HSS construction reduces overhang and significantly improves stability during drilling, which means fewer deflections and cleaner holes in steel and non‑ferrous metals. The reduced free length of the shank makes the bit better suited to tasks that demand precision rather than reach, especially when used with portable or benchtop drilling equipment. For operators seeking dependable repeatability, this geometry minimises chatter and supports tighter hole tolerances. Easier centring and lower drilling forces with a 118° tip The 118° point angle is tuned for efficient entry into softer metallic materials and for quick centring on curved or uneven surfaces. A sharpened tip reduces the cross‑cut width at the very tip, lowering friction and thus the required feed force; this improves guidance during start‑up and reduces the risk of walking. For users, that means smoother starts, less effort and a neater finish on workpieces such as Aluminium, mild Steel and various non‑ferrous metals. Application range and user benefits for metalworking This Type N Twist Drill is primarily intended for drilling in metal and performs well on alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and Plastics. The roll‑formed HSS manufacturing process imparts elastic toughness that helps to prevent breakage when drilling holes below about 6 mm diameter, making it a sound choice for workshops, maintenance teams and production environments where small‑diameter metal holes are common. Regrinding is straightforward, extending the service life for skilled users. DIN 338 conformity ensures compatibility and quality Manufactured to the DIN 338 specification for short cylindrical‑shank twist drills, this product adheres to established dimensional and execution standards. That guarantees interchangeability with fixtures and chucks and gives assurance about tolerances and shaft form. For buyers, that means predictable fitment in standard drill chucks and consistent performance across batches, supporting quality assurance in professional settings. For precision metalworking choose the MetavCUT Twist Drill Type N with Short HSS design — METAV Werkzeuge offers expert technical advice and personal support: info@metav-werkzeuge.com • +49 2822 7131930 • WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40050-FDA Diameter: 5 mm Point Angle: 118° Spiral Length: 52 mm Overall Length: 86 mm Execution: Short Type: Type N Material: HSS Colour: Black For Drilling Machine: Drilling Machine (Hand drill suitable) Application: Drills for metal Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill Type N is used chiefly for drilling in metal; it is suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and Plastics and is particularly effective for tasks requiring stable, precise holes in smaller diameters. Which three drill types exist? Commonly distinguished drill types are Metal drill bits, Wood drill bits and Masonry/Concrete drill bits; the MetavCUT Twist Drill Type N belongs to the Metal drill category and is optimised for those applications.
6.1mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 6.1 mm, HSS, Short, 118° Tip, Black, DIN 338 by MetavCUT The Twist Drill is a short HSS metal drill designed for precision drilling in steel and non-ferrous metals, suitable for Hand Drills and Drilling Machines. Short HSS design for high stability Conforms to DIN 338 for short cylinder shank drills 118° tip for reliable centring and entry Suitable for alloyed and unalloyed steel and non-ferrous metals Robust black finish for workshop durability Precision and Stability for Metalworking The Twist Drill (MetavCUT, Type N) with a 6.1 mm diameter and 118° tip offers increased rigidity thanks to its Short overall length. This reduced overhang minimises bending and runout, which improves hole accuracy when used in Hand Drills or stationary Drilling Machines. For tasks that demand repeatable, concentric holes in metal, the short geometry delivers better guidance and less vibration than longer bits, resulting in cleaner results and longer tool life. Standardised Short Design for Consistent Results Manufactured to DIN 338, the Twist Drill (MetavCUT, Type N) follows the classification for short spiral drills with cylinder shank. The standard ensures defined dimensions, tolerances and compatibility with common chucks, making tool changeover straightforward. Because the geometry and length are standardised, repeat production and jig-based operations benefit from predictable performance and easier quality control. HSS Material and Application Recommendations Made from HSS (High Speed Steel), this Twist Drill is optimised for standard metalworking tasks. The roll-walzed production process yields a tougher, more elastic flute body that reduces fracture risk, especially for diameters below 6 mm. Recommended materials include alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. When used in harder materials, adapted speeds and cutting fluids extend life; for softer materials the 118° tip aids initial centring and reduces walking. Target Users and Practical Advantages Designed for workshops, maintenance technicians and hobbyists who require robust, repeatable drilling in metal, the Twist Drill (MetavCUT, Type N) shines in setups where stability and precision matter. The short execution supports precise manual drilling and machine operations alike. For users unsure about drill selection or compatible machine settings, METAV Werkzeuge offers competent advice to match the drill to the workpiece and machining conditions. Strong recommendation: For reliable metal drilling choose the MetavCUT Twist Drill Type N with 6.1 mm diameter and 118° tip — for personalised technical advice contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill / Spiralbohrer Brand: MetavCUT SKU: 40061-FDA Diameter: 6.1 mm Tip angle: 118° Type: Type N Material: HSS (High Speed Steel) Execution: Short Colour: Black Spiral length: 57 mm Total length: 101 mm For use in: Hand Drill / Drilling Machine Standard: DIN 338 Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N best used for? The Twist Drill from MetavCUT (Type N) is primarily designed for drilling metal; it is well suited to alloyed and unalloyed steels, cast iron and non‑ferrous metals where a robust, standard short HSS geometry is required. Can the MetavCUT Twist Drill Type N be used in a hand drill? Yes, the Twist Drill (MetavCUT, Type N) is suitable for Hand Drills as well as Drilling Machines; its short overall length increases stability and reduces the risk of breakage during manual operation. For what is a Twist Drill used? A Twist Drill (MetavCUT, Type N) is mainly applied to the machining of high‑strength workpieces and larger hole diameters; its form is easy to resharpen and it withstands higher loads, which makes it the tool of choice for many metalworking tasks. Which three drill types are common? Common drill types include Metal Drill, Wood Drill and Stone/Concrete Drill, and the MetavCUT Twist Drill corresponds to the Metal Drill category. Why are Twist Drills sharpened at the tip? Sharpening reduces the cross‑cut at the tip of the Twist Drill (MetavCUT, Type N), lowering friction forces and thus reducing required feed forces while improving centring in the workpiece. Can a metal Twist Drill be used in wood? A Metal Drill such as the MetavCUT Twist Drill can be used in wood, but it typically provides poorer guidance and a less clean finish than dedicated Wood Drills; however it is easier to resharpen and has lower self‑feeding tendency. For which drilling depths is the Twist Drill most used? A solid hole is commonly executed with a Twist Drill (MetavCUT, Type N). For diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most frequently used tool. Is HSS or HSSE better? The general assumption that HSSE is always superior to HSS is incorrect; choosing between HSS and HSSE for a MetavCUT Twist Drill (Type N) depends on working conditions and whether the higher acquisition cost of HSSE is justified by the specific application.
6.25mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 6.25 mm, HSS, short, black, DIN 338 The Twist Drill Type N is a short HSS metal drill designed for stable, precise drilling in steel and other metals using handheld drills or drilling machines. Twist Drill Type N for metal drilling Short HSS design for enhanced stability DIN 338 compliant for short cylindrical drills 118° tip angle for reliable centering Suitable for drilling machines and hand drills Stable performance for demanding metalwork The Twist Drill from MetavCUT combines a short fluted design with HSS material to deliver high rigidity and reduced deflection when drilling into metal. Because the cutter length is reduced relative to standard drills, vibration and runout are minimised, which directly improves hole accuracy and extends tool life. This stability benefits maintenance technicians and workshop professionals who require repeatable centre-to-centre accuracy on metal fabrications. Precise centring and cleaner hole starts A 118° tip angle provides a balanced compromise between initial penetration and centring behaviour, making the drill well suited to typical steels and general metalwork. The geometry lowers the tendency to “walk” on curved or painted surfaces, so fewer pilot holes are needed and setup time is reduced. Users achieve cleaner hole edges and consistent drilling results even when working without elaborate jigs. Standardised dimensions for dependable tooling choices Compliance with DIN 338 ensures the short cylindrical shank and overall geometry match common toolholder and chuck standards, simplifying tool selection and replacement. The HSS designation (High Speed Steel) indicates good toughness and edge retention for standard metal drilling tasks. This combination enables workshops to maintain inventory consistency while choosing a tool that balances cost and performance. Application range and user guidance Engineers, metal fabricators and service technicians will find this Type N drill particularly useful for general-purpose drilling in alloyed and unalloyed steels, cast iron and non-ferrous metals. For best results, select proper cutting speeds and use cutting fluid when drilling steels above moderate hardness; this reduces heat, preserves the cutting edge and improves cycle time. Note that for very soft materials or abrasive masonry, material-specific drills are preferable. Strong recommendation: For precision metal drilling choose the MetavCUT Twist Drill Type N with short HSS design — METAV Werkzeuge offers expert advice and technical support via info@metav-werkzeuge.com, phone +49 2822 7131930 and WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 400625-FDA Diameter: 6.25 mm Material: HSS (High Speed Steel) Type: Type N Execution: short Colour: black Tip angle: 118° Spiral length: 57 mm Overall length: 101 mm Standard: DIN 338 Application: Drills for metal For drill machine: Drilling Machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT used for? The MetavCUT Twist Drill Type N is primarily applied to metalworking tasks; it is intended for drilling into high-strength materials and larger diameters where robust performance is required. Its form allows relatively easy resharpening and it tolerates higher loads during cutting. Which three drill types exist? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials. Why are twist drills pointed? Pointing the tip of a twist drill reduces the cross-cutting edge at the tip, which significantly lowers friction and required feed forces; this sharpening also improves centre holding so the drill seats more accurately in the workpiece. Can a Twist Drill be used to drill wood? A metal-oriented Twist Drill such as the MetavCUT Type N can be used in wood, but guidance is reduced and the finish is typically less clean than with a dedicated wood bit; advantages include easier resharpening and less aggressive self-feeding. At what drilling depths are twist drills most commonly used? Twist drills are the standard choice for through-hole drilling; they are most frequently used for diameters up to 20 mm and drilling depths up to about 100 mm, making them suitable for typical workshop operations. What is better, HSS or HSSE? The assumption that HSSE is always superior to HSS is not universally correct; decision-making should consider working conditions and whether the slightly higher investment in HSSE is justified by the specific application.
6.2mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS, Ø 6.2 mm, 118°, black, DIN 338, MetavCUT The Twist Drill Type N short HSS is a precision metalworking drill with a 6.2 mm diameter, a 118° tip angle and a compact design for stable, accurate holes in metal. Short HSS design for improved stability DIN 338 compliant short twist drill 6.2 mm diameter for precise metal holes 118° tip for controlled entry Suitable for drilling machines and hand drills Stable drilling for accurate metal holes The short HSS construction reduces overhang and vibration, delivering higher stability and more precise results when machining metal. Because the flute length is reduced, the tool resists bending and provides consistent concentricity in through-holes. This results in cleaner bores and less rework when working on components that demand tight tolerances. Material and geometry explained for reliable results Made from High Speed Steel (HSS), the drill combines toughness with wear resistance ideal for common metalworking tasks. The 118° tip angle eases centring on curved or softer surfaces and lowers the initial cutting forces; this geometry is particularly effective for general metal grades and reduces the chance of walking at the start of the hole. Short drills per DIN 338 are optimised for rigid setups and stationary or portable drilling machines. Where this drill excels and who benefits Designed primarily as a Drills for Metal tool, the Type N short configuration suits workshops, toolrooms and maintenance pros seeking repeatable performance in steel, cast iron, non-ferrous metals and plastics. The compact format is beneficial for confined setups or when using hand-held drilling devices, delivering greater control and faster, more reliable hole-making for production and repair tasks. Choose the MetavCUT Twist Drill Type N short HSS for dependable metal drilling — for personalised technical advice and application support contact METAV Werkzeuge: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40062-FDA Diameter: 6.2 mm Spiral length: 57 mm Overall length: 101 mm Tip angle: 118° Type: Type N Execution: short Material: HSS Colour: black Suitable for: Drilling Machine (Hand Drill) Application: Drills for Metal Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N by MetavCUT used for? The MetavCUT Twist Drill Type N is primarily used for machining metal; it is particularly suitable for drilling in alloyed and unalloyed steel, cast iron, non-ferrous metals and certain plastics. Its short HSS design makes it robust for demanding tasks and larger drill diameters where stability and precision are required. Which three drill types are commonly available? Common drill categories are metal drills, wood drills and stone/masonry drills. The MetavCUT Twist Drill Type N falls into the metal drills group and is tailored to metalworking applications.
6.3mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, Ø 6.3 mm, 118° point angle, short HSS, black, DIN 338 — MetavCUT The Twist Drill Type N is a short HSS metal-drilling bit designed for use in hand and drilling machines, offering precise, stable performance for metalworking tasks. Short HSS design for increased stability Conforms to DIN 338 for short twist drills 118° point angle for reliable centring on common metals Suitable for alloyed and unalloyed steel and non-ferrous metals Black finish reduces glare and aids chip evacuation Precision and durability for metalworking professionals The short HSS construction of this Twist Drill provides enhanced stability and reduced deflection during machining, making it ideal for accurate holemaking. Manufactured to DIN 338 specifications, the reduced projection length minimises chatter and improves concentricity when drilling in steel and cast iron. This results in consistently round holes and longer tool life compared with longer, more flexible bits. Versatile tip geometry that aids centring and feed Equipped with a 118° point angle, this Type N bit balances entry behaviour and cutting forces for general-purpose metal drilling. The geometry supports easier centring on slightly curved or irregular surfaces and is effective across a range of common metals. For users seeking a classic “Normal Spiral” performance, this bit provides a dependable compromise between fast penetration and controlled cutting action. Practical advantages for workshop and maintenance tasks This short Twist Drill excels in workshop and maintenance environments where accessibility and rigidity matter. The compact overall length reduces the exposed shank, lowering the risk of bend or breakage under side loads. For repetitive repair or assembly work on machinery and metal components, the improved stiffness translates into fewer broken bits and a more predictable drilling process. Material suitability and manufacturing benefits explained Made from High Speed Steel (HSS), the bit is suitable for alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. HSS offers a favourable combination of hardness and toughness; roll-formed HSS variants reduce the risk of breakage for small-diameter drills and maintain edge integrity during standard metalworking operations. The Type N normal spiral is the classic choice for metal drilling and can be resharpened when necessary to extend service life. Strong recommendation: Choose the MetavCUT Twist Drill Type N for reliable, precise metal drilling; for personalised advice or technical data METAV Werkzeuge provides expert support — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 40063-FDA Diameter: 6.3 mm Spiral Length: 63 mm Overall Length: 101 mm Point Angle: 118° For Drill: Drilling Machine / Hand Drill Type: Type N Material: HSS (High Speed Steel) Execution: short Colour: black Application: Drills for metal Standard: DIN 338 Manufacturer: MetavCUT Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill Type N be used on? The MetavCUT Twist Drill Type N, made of HSS, is intended primarily for metalworking and is suitable for alloyed and unalloyed Steel, Cast Iron, Non‑Ferrous Metals and various Plastics; this composition provides a balance between hardness and toughness for common workshop tasks. What is a Twist Drill used for? A Twist Drill, such as the MetavCUT Twist Drill Type N, is mainly applied to the machining of high‑strength materials and larger drill diameters; its form allows straightforward resharpening and it withstands higher loads during drilling. Which 3 drill types are there? The three main drill categories are Metal Drills, Wood Drills and Masonry/Concrete Drills.
6.4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 6.4 mm, 118°, black, DIN 338, MetavCUT The Twist Drill Type N short by MetavCUT is a compact metalworking drill for precise holes in steel and non-ferrous materials, designed for use with a hand drill and compliant with DIN 338. 6.4 mm diameter for accurate metal holes Short design per DIN 338 for high stability HSS material for elasticity and wear resistance 118° point angle for reliable centering Stability and precision for demanding metalworking A short spiral drill made to DIN 338 reduces overhang and vibration, so even thin-walled components can be drilled with greater dimensional accuracy. The reduced exposed length improves rigidity and lowers the risk of deflection, which means cleaner holes and less rework for metalworking professionals. This compact design is particularly advantageous when working from fixed jigs or on small workpieces where stability is essential. High-Speed Steel construction for standard machining tasks Manufactured from HSS (High Speed Steel), this Type N short drill combines toughness with a degree of flexibility that reduces fracture risk during common metal drilling jobs. For standard operations in alloyed and unalloyed steel, cast iron, non-ferrous metals and plastics, the material choice supports longer tool life under frequent use. The construction method improves resistance to chipping when drilling diameters under 6 mm and contributes to consistent drilling performance. Tip geometry and application suitability explained The 118° point angle favours reliable centering and controlled penetration in softer to medium-hard metals, making it well suited for general workshop use. As a Type N twist drill, it is optimised for metalworking rather than soft timber; the point geometry and flute design balance chip evacuation with cutting stability. Correct feed and moderate speeds prolong service life and yield round, burr-minimised holes for subsequent finishing operations. Who benefits from this short Type N twist drill Workshops, maintenance technicians and precision hobbyists seeking a robust everyday metal drill will appreciate the combination of 6.4 mm diameter, short overall length and HSS material. The tool is intended for use in hand-held drilling machines and small bench machines where operator control and low runout are priorities. Its design supports repeatable results for production runs of small to medium series or for single, critical repair tasks. Choose the MetavCUT Twist Drill Type N short for dependable metal drilling performance — for technical advice or to confirm suitability for your application contact METAV Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 | WhatsApp +49 170 2837271 Technical Data Designation: Twist Drill Brand: MetavCUT SKU: 40064-FDA Diameter: 6.4 mm Spiral length: 63 mm Overall length: 101 mm Point angle: 118° Type: Type N Execution: short For use with: Hand Drill Colour: black Material: HSS Application: Drills for metal Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill Type N short best used for? The MetavCUT Twist Drill Type N short is primarily used for drilling metal; it excels in producing precise holes in alloyed and unalloyed steels, cast iron and non-ferrous metals when used in hand-held or small stationary drilling machines. Can the Twist Drill Type N short be used in wood? The MetavCUT Twist Drill Type N short can be used in wood, but as a metal-optimised drill it provides less guidance and a rougher finish than dedicated wood drills; it is easier to resharpen yet offers reduced self-feeding compared with timber-specific bits. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high-strength materials and larger drill diameters; their form makes them straightforward to resharpen and able to withstand higher loads. Which three drill types exist? The principal categories are Metal drill, Wood drill, and Stone/Concrete drill. Why are twist drills sharpened (pointed)? Pointing reduces the cross edge at the tip of the Twist Drill, lowering friction and required feed forces while improving the drill's centring in the workpiece. At what drilling depths are twist drills most commonly used? A solid through-hole is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most common tool. Is HSS or HSSE better? The general assumption that HSSE steels are always superior to HSS is not universally correct; selection should consider actual working conditions and whether the higher cost of HSSE is justified.
6.5mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT überzeugt durch seine Kombination aus HSS-Material, kurzer Ausführung und der Einhaltung der DIN 338, was hohe Stabilität und zuverlässige Ergebnisse beim Metallbohren gewährleistet. Bestellen Sie den Bohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung an, falls Sie spezielle Einsatzfälle besprechen möchten. Spiralbohrer 6,5 mm von MetavCUT (HSS, Typ N, kurz) Der Spiralbohrer von MetavCUT eignet sich für präzise Metallbohrungen auf Handbohrmaschinen und stationären Geräten und bietet Stabilität durch kurze Bauart. Kurze Ausführung für hohe Stabilität HSS-Material für Stahl und Gusseisen DIN 338 konform für kurze Spiralbohrer Spitzenwinkel 118° für einfache Anbohrung Zylinderschaft geeignet für Handbohrmaschine Stabilität und Präzision für alltägliche Metallarbeiten Die kurze Ausführung des Spiralbohrers reduziert die Auskraglänge und erhöht dadurch die Stabilität beim Bohren. Gerade bei einem Durchmesser von 6,5 mm sorgt die reduzierte Hebelwirkung für saubere, maßhaltige Bohrungen und weniger Vibrationen. Werkstätten und Montagebetriebe profitieren von der höheren Standzeit und der geringeren Bruchgefahr gegenüber längeren Ausführungen, insbesondere bei gängigen Bohranwendungen in Stahl, Aluminium und Guss. HSS und Normen geben Planungssicherheit Der Bohrer besteht aus HSS (High Speed Steel), was eine gute Elastizität und Verschleißfestigkeit kombiniert. Die Fertigung nach DIN 338 klassifiziert ihn als kurzen Spiralbohrer mit Zylinderschaft und garantiert eine standardisierte Abmessung und Handhabung. Der Spitzenwinkel von 118° erleichtert das Anbohren auf leicht gewölbten Flächen und ist eine bewährte Wahl für allgemeine Metallbearbeitung. Passende Einsatzbereiche und Maschinenkompatibilität Dieser Spiralbohrer ist ausgelegt für den Einsatz im Standard-Bereich (2,0 mm bis 13,0 mm) und eignet sich für Handbohrmaschinen sowie stationäre Bohrmaschinen. Typische Anwendungen sind das Bohren in Baustahl, Aluminium, Nichteisenmetallen und Kunststoffen. Die Zielgruppe umfasst Handwerk, industrielle Werkstätten und ambitionierte Heimwerker, die eine robuste Lösung für Routinebohrungen suchen. Anwendungstipps für lange Lebensdauer Für optimale Ergebnisse empfiehlt sich das Anpunkten mit einem Zentrierbohrer bei hoher Präzision und der Einsatz von Kühlmittel oder Schneidöl bei Stahl, um Wärmeentwicklung und Werkzeugverschleiß zu reduzieren. Moderate Drehzahlen und gleichmäßiger Vorschub verlängern die Lebensdauer. Vermeiden Sie sehr tiefe Bohrungen ohne Zwischenspülung, da die Späne zuverlässig abgeführt werden müssen. Für präzise Metallbearbeitung empfiehlt MetavCUT diesen HSS-Spiralbohrer als zuverlässige Alltagslösung — Für Bestellungen oder technische Fragen kontaktieren Sie Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 40065-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Ausführung: kurz Norm: DIN 338 Daten Durchmesser: 6,5 mm Gesamtlänge: 101 mm Spirallänge: 63 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS (High Speed Steel, Schnellarbeitsstahl) Typ: Typ N (Normalspirale) Farbe: schwarz Für: Handbohrmaschine Eignung: Bohrer für Metall FAQ Für welche Materialien ist der Spiralbohrer geeignet? Der Spiralbohrer von MetavCUT ist geeignet für legierten und unlegierten Stahl, Gusseisen, Nichteisenmetalle und Kunststoffe; bei harten Werkstoffen sind passende Schnittparameter und Kühlung zu beachten. Ist der Bohrer für Handbohrmaschinen geeignet? Ja, der Spiralbohrer mit Zylinderschaft ist kompatibel mit Handbohrmaschinen und eignet sich besonders für den Standard-Bereich von 2 mm bis 13 mm. Welchen Spitzenwinkel hat der Bohrer und was bedeutet das praktisch? Der Spiralbohrer hat einen Spitzenwinkel von 118°, was das Anbohren erleichtert und gutes Zentrierverhalten auf glatten oder leicht gewölbten Oberflächen ermöglicht. Nach welcher Norm ist der Bohrer gefertigt? Der Bohrer entspricht der Norm DIN 338, die kurze Spiralbohrer mit Zylinderschaft definiert und damit einheitliche Abmessungen sowie Einsatzbereiche sicherstellt. Welche Artikelnummer hat dieses Produkt für die Bestellung? Die Artikelnummer lautet 40065-FDA; bei Rückfragen zur Eignung oder Lieferumfang hilft MetavCUT beziehungsweise Metav Werkzeuge gern weiter.
6.6mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, Ø 6.6 mm, 118°, black, DIN 338 The Twist Drill Type N is a short High Speed Steel drill designed for precision metal drilling on Drilling Machines and handheld drills. Short design for higher stability HSS material for reliable metal drilling DIN 338 conformity for consistent quality 118° point angle for improved centring Black colour for easy identification High-performance metal drilling with consistent results The Twist Drill from MetavCUT is engineered for demanding metalworking tasks where precision and stability matter. With a diameter of 6.6 mm and a 118° point angle, this short-version Type N drill enters the material cleanly and reduces wandering on curved or slightly uneven surfaces. The roll-welded HSS construction provides elasticity and durability during standard operations, making it suitable for both unalloyed and alloyed steels as well as non-ferrous metals and selected plastics. The short length reduces deflection and supports repeatable, accurate holes in machining and maintenance work. Robust design and clear standards for safe use Built to the DIN 338 specification for short Twist Drills with cylindrical shank, this tool emphasises repeatability and tool life. The reduced overall length increases rigidity and lowers the risk of bending under load, so feeds and speeds can be applied more aggressively while maintaining hole quality. The short execution also simplifies clamping in conventional chucks and minimises runout. For operators unfamiliar with terms: HSS stands for High Speed Steel, a material balanced for hardness and toughness under typical drilling temperatures. Who benefits and where to use it This Type N short Twist Drill is intended primarily for metalworkers, maintenance technicians and workshop users who require a compact, reliable drill for everyday drilling in metal. It is particularly effective in situations where free-standing reach is limited or where high stiffness prevents chatter. Even small-scale fabrication and repair shops will appreciate the easier handling and better centring behaviour on thin or curved components. If uncertainty remains about suitability for a specific job, MetavCUT and the retailer provide expert guidance to match tooling to the application. Handling tips and safety recommendations To achieve the best results with this short Twist Drill, use appropriate cutting speeds, steady feed and suitable lubricants for the target material. Short drills are less prone to breakage, but correct clamping and alignment remain essential for hole quality. The Type N spiral geometry is optimized for metal; when drilling different materials, adjust speed and lubrication accordingly. If post-processing or reworking is required, the HSS material allows straightforward resharpening to restore tip geometry and extend service life. MetavCUT recommends this Twist Drill for precision metalworking and short-reach drilling; for further technical advice or application-specific recommendations contact METAV Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930, WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT Diameter: 6.6 mm Point angle: 118° Total length: 101 mm Spiral length: 63 mm Material: HSS (High Speed Steel) Type: Type N Execution: short Suitable for: Drilling Machine Application: Drills for metal Standard: DIN 338 Colour: black Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for and where is the MetavCUT Type N Twist Drill suitable? The MetavCUT Twist Drill Type N is mainly used for machining higher-strength materials and for larger drilling diameters in metalworking. Its short HSS design offers good elasticity and reduced breakage risk for holes under typical workshop conditions. This form is relatively easy to resharpen and withstands higher loads, making it a dependable choice for metal fabrication and repair. Which three drill types exist and how does this Twist Drill compare? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill category and is optimized for steel and non-ferrous metals; it differs from wood or masonry drills in point geometry and flute design, which are tailored to the specific material properties.
6.7mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 6.7 mm, HSS, 118° Tip, Short, Black, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS metalworking drill designed for Drilling Machines, delivering precise, stable holes in steel and other metals. Type N Twist Drill for metalworking HSS Material for high wear resistance 6.7 mm Diameter for precise holes 118° Tip for reliable centring Short design per DIN 338 for maximum stability Durable High-Speed Steel for demanding metalwork HSS (High Speed Steel) gives this Twist Drill excellent elasticity and wear resistance under demanding conditions. Because HSS is manufactured to withstand high cutting temperatures, the drill maintains edge hardness during continuous use, which reduces the risk of breakage when drilling holes below 6 mm diameter and improves service life on larger diameters. This material choice supports consistent performance when working with alloyed and unalloyed steel, cast iron, non-ferrous metals and many Plastics. Precise centring and consistent hole quality The 118° tip angle is optimised for softer to medium-hard materials and helps the drill to centre reliably on slightly curved or uneven surfaces. A smaller tip angle reduces the initial bite and lowers the required feed force, which improves control during start-up and produces cleaner holes with reduced burr formation. For applications demanding tight tolerances, the short flute length and robust geometry contribute directly to repeatable, accurate results. Designed for professional metalworkers and workshops Engineered for workshop environments and machine use, this short Twist Drill offers increased rigidity and less deflection during operation. The compact configuration makes it suitable for precision jobs on lathes, pillar drills and other Drilling Machines where stability is essential. Professionals who prioritise accuracy and tool durability benefit from the combination of short design and HSS construction. Standards, type and practical advantages explained Compliant with DIN 338, this short Twist Drill follows the standard for short cylindrical-shank HSS drills and therefore matches common expectations for fit and performance. The designation Type N indicates the Normal spiral profile, a classic geometry optimised for metal drilling. Shorter overall length reduces chatter and improves concentricity; this makes the tool especially practical for applications where bending of the drill must be avoided and precise alignment is required. Strong recommendation: For reliable, accurate metal drilling choose the MetavCUT Twist Drill Type N with HSS construction and DIN 338 short design — for technical questions or personalised advice contact METAV Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271) Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40067-FDA Typ: Typ N Durchmesser: 6.7 mm Spitzenwinkel: 118° Spirallänge: 63 mm Gesamtlänge: 101 mm Material: HSS Norm: DIN 338 Ausführung: short Farbe: black Anwendung: Drills for metal Suitable for: Drilling Machine Verpackungseinheit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for and which materials suit it best? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is especially suited to high-strength materials and larger diameters because its form is simple to regrind and withstands higher loads, making it a reliable choice for demanding metalworking tasks. Which three drill types exist? The three common drill categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the metal-drill category and is optimised for metalworking applications. Why are Twist Drills pointed? The point grind reduces the cross-cutting edge at the tip of the Twist Drill, which lowers friction and therefore decreases required feed forces; at the same time a pointed tip improves centring in the workpiece for more accurate drilling. Can a Twist Drill be used to drill wood? A metal Twist Drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are typically worse than with a dedicated wood drill; however, metal drills are easier to regrind and exhibit lower self-feed, which can be an advantage in some situations.
6.8mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS, 6.8 mm, 118° tip, black, DIN 338, MetavCUT The Twist Drill is a short Type N HSS drill designed for precise metal drilling, suitable for use in Hand Drills and Drilling Machines for demanding, stable holemaking. Short HSS Twist Drill for high stability 6.8 mm Diameter for Precise Metal Holes 118° Tip Angle for reliable centring DIN 338 compliant, Type N metal drill Black finish, 109 mm Overall Length Greater Precision and Less Wander for Metalworking A shorter cutting length gives this bit superior stability and reduced deflection when compared with longer counterparts. The compact geometry of the Twist Drill minimises vibration and provides a steadier bore in steel and other metals, which results in cleaner holes and less rework. For operators who value repeatable accuracy, the short design translates directly into faster setup and higher first-pass yield. High-Speed Steel Explained — Durability for Standard Tasks Made from HSS (High Speed Steel), the drill offers good edge retention and resilience under typical metalworking loads. HSS is produced to withstand elevated temperatures during cutting, and because this bit is roll-walden in manufacturing, it combines elasticity with lower fracture risk on holes below 6 mm; at 6.8 mm the material still benefits from HSS properties for alloyed and unalloyed steels, cast iron, non-ferrous metals and many plastics. The 118° tip angle supports easier penetration in softer metals and improves the initial centring action. Practical Use: Who Benefits from This Bit This Type N Twist Drill is aimed at professional workshops and skilled hobbyists who perform precision drilling in metal components. Its properties make it suitable for maintenance tasks, component fabrication and retrofit work where a robust short bit reduces chatter and slotting. Because the bit follows DIN 338 specifications, users who demand standardised geometry and interchangeability will find it simple to integrate into existing toolsets and workflows. Standard Compliance and Design Advantages Conforming to DIN 338, the short configuration and cylindrical shank enable easy clamping and consistent concentricity in chucks of Hand Drills and Drilling Machines. The 63 mm spiral length and 109 mm overall length balance chip evacuation with rigidity, while the 118° Tip Angle helps with centring on slightly rounded surfaces and reduces the risk of walking. The black surface finish aids in visibility and handling without affecting cutting performance. We recommend MetavCUT’s Twist Drill Type N as the dependable choice for precise metal drilling — for expert advice or to ensure the tool matches your specific application, contact METAV Werkzeuge: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 40068-FDA Diameter: 6.8 mm Tip Angle: 118° Spiral Length: 63 mm Overall Length: 109 mm Execution: Short Type: Type N Material: HSS Standard: DIN 338 Colour: Black Application: Drills for Metal For: Hand Drill / Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill by MetavCUT used for? The MetavCUT Twist Drill Type N is primarily used for drilling in high-strength materials and larger diameters; it is well suited to metalworking tasks. Its shape is easy to regrind and withstands heavy loads, which makes it a reliable choice for workshop and industrial applications. Which three drill types exist? Common drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for steel and similar materials. Why are Twist Drills re-pointed? Re-pointing reduces the chisel edge at the tip of the Twist Drill, significantly lowering friction and thus the required feed forces. At the same time the re-pointed tip improves centring in the workpiece. Can a metal Twist Drill be used in wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and have less self-feeding action. For which drilling depths is the Twist Drill most used? A through-hole in solid material is typically executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm the Twist Drill is the most commonly used tool. What is better, HSS or HSSE? The general belief that HSSE is always superior to HSS is incorrect. When choosing between HSS and HSSE for a MetavCUT Twist Drill, evaluate the working conditions carefully to decide whether the higher cost of HSSE is justified.
Built for reliable workshop performance and clean holes
The hss twist drill, din 338, type n in short, roll-formed design delivers robust, repeatable drilling for daily workshop use. Designed from high-speed steel with a 118° conical point and a black surface finish, this short twist drill combines stability and wear resistance for precise work on a wide range of materials.
How this drill improves machining efficiency
The short, roll-formed geometry increases fracture resistance and stiffness, reducing chatter and breakages in hand and pillar drills as well as in light series production. The 118° point angle and ground mantle profile produce neat hole entry and reliable centring in materials up to ≈900 N/mm². Synonyms used for clarity: hss drill, short roll-formed twist drill.
Practical benefits for production and maintenance
- Enhanced tool life through roll-formed geometry and black surface reducing friction and wear
- Versatile material capability for alloyed and unalloyed steels, cast parts, sintered metals, non-ferrous metals and plastics
- Stable drilling for hand and pillar machines and short-series production
- Consistent hole quality courtesy of the 118° point and din 338 type n specification
Key technical data at a glance
- hss (high-speed steel)
- din 338, type n
- short, roll-formed design
- point angle: 118°
- black surface finish (reduced friction/wear)
- suitable for materials up to ≈900 N/mm²
- recommended use: hand drills, pillar drills, series work
Why Metav is the sensible supplier choice
Metav stands for democratisation of precision: decades of expertise, a quality filter in Emmerich and a range that covers from precision measuring tools to full workshop equipment. With more than 48,000 customers and over 250,000 products, Metav offers dependable availability and a centralised supply for industrial buyers who prioritise consistent quality.
FAQ
Which materials can the hss twist drill machine reliably?
The hss twist drill is suitable for alloyed and unalloyed steels, cast components, sintered metals, non-ferrous metals and plastics up to approximately 900 N/mm².
What advantage does the short, roll-formed design provide?
The short roll-formed twist drill increases fracture resistance and rigidity, improving stability and reducing the risk of breakage during hand and pillar drilling or short-series production.
What does the black surface finish achieve?
The black finish reduces friction and wear, contributing to longer tool life and more consistent cutting behaviour for the hss drill.
How does the 118° point angle affect hole quality?
A 118° conical point gives cleaner hole entries and better centring on steels and similar materials, resulting in improved hole geometry and reduced walking.
In short: the hss twist drill, din 338, type n offers workshop-grade robustness and consistent hole quality, combined with the supply reliability and industry expertise Metav provides.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com