Reliable drilling performance with Standard Line twist drill
Standard Line twist drill and standard drills deliver consistent, precision holemaking for daily industrial and workshop use, combining durable high-speed steel construction with precision-ground flutes to ensure excellent runout and chip evacuation. Designed for machining unalloyed and low-alloy steel, cast iron, sintered metal, plastics and non-ferrous metals, these drills provide a balanced mix of wear resistance and hole quality for routine production and maintenance tasks. Ideal for workshops, maintenance departments and assembly plants, the system offers a dependable, cost-effective solution between entry-level and heavy-duty ranges, featuring an optimised 118° point for good penetration and centring. Key advantages include precision-ground construction, excellent chip evacuation and consistent hole quality.
4.2mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill (Spiralbohrer) — HSS-G long, 4.2 mm, 135° The Twist Drill (Spiralbohrer) is a long HSS-G drill bit designed for deep metal drilling with DIN 340 specification, ideal for use with a Drilling Machine. Long HSS-G design for deep holes Precise 4.2 mm diameter for accurate results 135° tip angle for harder materials Fully ground shank for high runout accuracy Bright finished surface for reduced adhesion High performance through HSS-G construction Designed as a long execution according to DIN 340, this HSS-G tool combines endurance and cutting efficiency. The fully ground geometry ensures sharp cutting edges and a high degree of roundness, which supports up to 40% faster drilling and requires 50% less feed force compared with conventional rolled HSS bits. This results in cleaner holes and less operator fatigue when working with legated and unlegated steels, cast materials and hard plastics. Deeper holes made accessible and precise With an overall length of 119 mm and a spiral length of 78 mm, the bit enables drilling in recessed or hard-to-access positions where standard lengths fall short. The 135° point angle improves performance on tougher materials by reducing initial chipping and improving centering, so fewer pilot operations are needed. This geometry is particularly suited to stainless and tempered steels where a flatter point reduces wander. Accurate handling and machine compatibility The ground shank and bright finish give excellent seating and reduced friction when clamped in chucks of a Drilling Machine. Because the bit is ground (HSS-G), it provides superior concentricity and hole quality; however, it is comparatively more brittle than rolled types and benefits from steady feed, proper cooling and preferably stationary machine use for maximum service life. The bit is engineered for routine workshop use and professional metalworking environments. Who benefits most from this design Production shops, maintenance teams and precision metalworkers will appreciate the combination of long reach and HSS-G performance for demanding tasks such as bushings, deep through-holes and repair work in cast and sintered parts. The tool is a reliable choice when deep, accurate holes in steels and non-ferrous metals are required and when regrinding capability is desirable for tool life extension. Strong recommendation: Choose the MetavCUT long HSS‑G Twist Drill for demanding metal drilling tasks and contact METAV Werkzeuge for expert, personalised advice and technical support — Email: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill (Spiralbohrer) Marke: MetavCUT SKU: 53042-FDA Durchmesser: 4.2 mm Spitzenwinkel: 135° Material: HSS-G Norm: DIN 340 Ausführung: long Gesamtlänge: 119 mm Spirallänge: 78 mm Schaft Ausführung: fully ground Farbe / Finish: bright finished Für Bohrmaschine: Drilling Machine Modellserie: Standard Line Anwendungen: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is a Twist Drill (Spiralbohrer) used? The Twist Drill from MetavCUT is primarily applied to machining high-strength materials and large drill diameters; its long design supports deeper holes and working in hard-to-reach positions. The ground form is easy to re-sharpen and withstands considerable loads, making it suitable for tougher metalworking tasks. Which three drill types exist? Commonly distinguished drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steels and similar materials. Why are Twist Drills re-sharpened (ausgespitzt)? Re-sharpening reduces the cross-edge at the tip, which lowers friction and thus requires less feed force; for the MetavCUT Twist Drill this improves centring and reduces cutting forces during the initial penetration into the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill such as the MetavCUT HSS-G Twist Drill can be used in wood, but guidance is poorer and the hole finish is not as clean as with a dedicated wood bit; metal drills are easier to re-sharpen and tend to have less self-feeding action in timber. For which drilling depths is the Twist Drill most used? A solid through hole is typically executed with a Twist Drill; for diameters up to about 20 mm and depths up to 100 mm the Twist Drill is the most frequently used tool, and the MetavCUT long execution is well suited for deeper bores. Is HSS or HSSE better? The common assumption that HSSE steels are always superior to HSS is not universally true. When choosing, evaluate whether the working conditions justify the higher cost of HSSE; the MetavCUT HSS-G long drill offers excellent performance for many standard applications. Are you unsure whether this tool meets your requirements or need additional technical data? METAV Werkzeuge provides comprehensive, expert consultation — Email: info@metav-werkzeuge.com | Phone: +49 2822 7131930 | WhatsApp: +49 170 2837271
4.3mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 4.3 mm, 118° | Short HSS, Black, DIN 338 The Twist Drill is a short Type N drill designed for metalworking, offering precise 4.3 mm holes with a 118° point angle for use in Drilling Machines and hand drills. Short HSS construction for stable drilling Conforms to DIN 338 for short twist drills 118° point angle for reliable centring Type N normal spiral optimised for metal Suitable for Drilling Machines and hand-held use High precision and efficiency for metalworking tasks The short HSS design delivers increased stability and reduced runout when working with metal. With a diameter of 4.3 mm and a 118° point angle, this short twist drill requires lower feed forces and centres reliably on typical metal surfaces. Its Type N normal spiral geometry is expressly intended for drilling steel, cast iron and other metallic materials, ensuring a clean hole with minimal burr formation. This combination of short length and hardened construction reduces the tendency to bend, which increases repeatable accuracy in series work. Robust performance where tool life matters Manufactured to the DIN 338 specification for short twist drills with cylindrical shank, this drill is suitable for conventional machining tasks on rotating tool-holders. The roll-formed HSS option offers improved elasticity and a lower risk of breakage for smaller diameters, making the tool resilient under normal workshop loads. For everyday metal-drilling operations, the material choice HSS (High Speed Steel) means reliable wear behaviour and straightforward resharpening when required, so the tool remains serviceable for longer. Easy handling and clear application guidance Because the drill is a short execution, it provides high rigidity and easier handling for both stationary Drilling Machines and portable hand machines. The Type N geometry is not optimised for very soft materials, but it performs consistently when used for its intended purpose: Drills for Metal. Users benefit from simpler set-up, stable cutting performance and predictable chip evacuation in typical workshop environments. For operators less familiar with drill geometries: a 118° point angle is generally preferable for softer metals and improves centring on curved or uneven surfaces. Practical maintenance and recommended use The roll-formed HSS variant reduces the chance of catastrophic breakage when drilling holes under 6 mm diameter; this makes upkeep and resharpening less critical for routine use. Resharpening a short twist drill restores the cutting lips while preserving the correct point angle, keeping the tool precise. When selecting drilling parameters, match speed and feed to the workpiece material and ensure secure clamping to exploit the drill’s stiffness and to prevent chatter or premature wear. Strong recommendation: For precision metal drilling choose the MetavCUT Twist Drill Type N with HSS short execution — METAV Werkzeuge offers expert advice and technical support by eMail at info@metav-werkzeuge.com, by phone at +49 2822 7131930 or via WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40043-FDA Diameter: 4.3 mm Spiral length: 43 mm Overall length: 80 mm Point angle: 118° Type: Type N Execution: short Material: HSS Colour: black Standard: DIN 338 Application: Drills for Metal For machine: Drilling Machine / Hand Drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best use for the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is intended primarily for metalworking; it is best used for drilling alloyed and unalloyed steel, cast iron and other metallic materials where a normal spiral geometry provides reliable cutting and chip removal. Can the MetavCUT Twist Drill be used in a hand-held drill? Yes, the MetavCUT Twist Drill with short execution and HSS material is suitable for both Drilling Machines and quality hand-held drills, offering improved rigidity and easier handling compared with longer designs. For what is a Twist Drill used? Twist Drills are mainly applied to the machining of high-strength materials and larger drill diameters; their form is easy to resharpen and they withstand higher loads. Which three drill types exist? The three main drill types are metal drills, wood drills and stone/concrete drills. Why are twist drills pointed? Pointing reduces the cross-cut at the tip of the twist drill. By pointing, friction forces are significantly lowered so that less feed force is necessary and the drill tip centres better in the workpiece. Can a twist drill be used to drill wood? A metal drill can also be used in wood; however, guidance is poorer and the result is not as clean. Metal drills are easier to resharpen and have a lower tendency to self-feed. For which drilling depths is the twist drill mostly used? A through-hole in solid material is performed with a twist drill. For diameters up to 20 mm and drilling depths up to 100 mm, the twist drill is the most commonly used tool. What is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to standard HSS steels is incorrect. When choosing, consider whether the working conditions justify the higher initial cost of HSSE.
4.3mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — MetavCUT; 4.3 mm; Short; HSS‑E; 135° point angle; 5% cobalt‑alloyed; Fully Ground; DIN 338 The Twist Drill (Type N) from MetavCUT is a short HSS‑E metal drill designed for precise, stable drilling in harder materials on drilling machines. Short design for higher rigidity and precision 4.3 mm diameter for precise metal holes 135° point angle for harder materials HSS‑E with 5% cobalt for enhanced durability Fully ground shank and DIN 338 conformity Precise holes through higher rigidity and stability The Twist Drill with a short design reduces the out‑of‑chuck overhang, resulting in noticeably less vibration and improved concentricity when machining metal. With a nominal 4.3 mm diameter and compact 47 mm spiral length, this drill delivers higher stability compared with longer variants, which directly benefits hole quality and repeatability. For workshop environments where accuracy matters, the reduced tendency to bend means fewer rejects and a steadier process, especially when using a dedicated Drilling Machine. Material choice and tip geometry tailored for hard materials Constructed from HSS‑E with 5% cobalt, the tool offers improved red hardness and wear resistance for demanding cuts. The 135° point angle is specifically chosen to ease entry and reduce chipping when working with harder steels and alloyed materials, while the Type N normal spiral remains the proven choice for general metalworking. Conformity to DIN 338 signals compatibility with industry expectations for short, cylindrical shank drills, and helps you match the right tool to the machining task. Fully ground geometry for accurate, clean drilling A fully ground flute and point geometry produce sharp cutting edges and excellent runout behaviour, resulting in clean bores and precise diameters. Grinding (CNC‑grind) creates the typical HSS‑G characteristics: high edge sharpness and excellent concentricity. Note that ground drills can be more brittle than rolled alternatives and benefit from correct clamping, moderate cutting parameters and adequate cooling to avoid premature fracture. The short variant reduces these risks further by minimising leverage on the cutting edge. Application focus, user guidance and workshop compatibility Designed primarily as a Drill for Metal, this short HSS‑E twist drill is ideal for workshop machinists, toolrooms and maintenance departments that require repeatable, accurate holes in alloyed and unalloyed steels, cast iron, non‑ferrous metals and plastics. The tool is best used in stationary or portable drilling machines with secure chucking and appropriate coolant. For customers unsure about cutting speeds, feeds or suitability for a specific material, METAV Werkzeuge offers competent support and technical advice to match the tool to the job. Strongly recommend MetavCUT Twist Drill Type N for precision metalworking — for expert guidance and ordering assistance contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47043-FDA Diameter: 4.3 mm Spiral length: 47 mm Overall length: 80 mm Point angle: 135° Type: Type N Version: short Shaft execution: fully ground Material: HSS‑E Colour: 5% cobalt-alloyed For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Norm: DIN 338 Execution: kurz Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill Type N is mainly applied when machining high‑strength materials and larger drilling diameters; its shape allows relatively easy re‑sharpening and it withstands higher loads, making it suitable for robust metalworking tasks. Which three drill types are there? Typical categories are metal drills, wood drills and stone/concrete drills, and the MetavCUT Twist Drill is positioned within the metal drill group for machining metals. Why are Twist Drills point‑sharpened? The point sharpening reduces the cross‑cut at the tip, which lowers friction and therefore requires less feed force; with the MetavCUT Twist Drill this also improves centring of the tip in the workpiece. Can you use a metal drill for wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance is poorer and hole quality is usually inferior; the advantage is easier re‑grinding and less tendency for self‑feeding, but expect a rougher finish. At what drilling depths is the Twist Drill most commonly used? A through‑hole is typically made with a Twist Drill; for diameters up to about 20 mm and depths up to approximately 100 mm the Twist Drill is the most frequently used tool, and the MetavCUT short variant is optimised for stability at such depths. What is better, HSS or HSSE? The common belief that HSSE steels are always superior to HSS is not universally correct; when choosing a MetavCUT Twist Drill, evaluate whether the specific working conditions justify a higher‑cost HSSE tool, since HSS‑E may already provide the required performance.
4.3mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
Body Drill (Twist Drill) — Double‑Ended HSS‑G, Ø 4.3 mm, 135° The Body Drill is a double‑ended Twist Drill from MetavCUT designed for precise metalworking and drilling machines, ideal for short, stable holes in sheet metal and chassis applications. Double‑ended design for two usable tips HSS‑G material for sharp, precise holes 135° tip angle for harder materials Fully ground shank for high concentricity Bright finished surface for easy chip evacuation Faster, more accurate metal drilling with a ground HSS design The Body Drill delivers a measurable productivity advantage: its HSS‑G construction and fully ground Flute Geometry enable up to 40% faster drilling with significantly lower axial force compared to conventional HSS bits. This makes shorter cycle times and reduced operator fatigue achievable, particularly when processing Alloyed and Unalloyed Steel. The 135° Tip Angle reduces chatter when penetrating harder materials, improving Hole Quality and prolonging tool life. Stable double‑ended format for workshop efficiency A Double‑Ended or double‑sided configuration means the tool functions like two drills in one: when one tip is worn, simply reverse the bit to use the other end. This design is especially valuable in high‑throughput sheet‑metal and chassis work where quick tip changes reduce downtime. The bright finished surface aids Chip Evacuation while the short overall length contributes to rigidity and better axial control during drilling. Clear suitability and handling recommendations for users This Twist Drill is specified for metalworking tasks and suits both stationary Drilling Machines and robust hand drills when used with proper clamping and coolant. For best results in Stainless Steel and other hard alloys, maintain steady spindle speed, use cutting fluid, and avoid excessive pecking; these measures preserve the HSS‑G cutting edges and help achieve round, burr‑reduced holes. Operators seeking repeatable precision will appreciate the high Round‑Run Accuracy of the fully ground Shank. Sustainable use, lifecycle and support from METAV Werkzeuge Choosing a durable ground HSS tool reduces consumable turnover and scrap from poor holes, supporting more efficient manufacturing practices. For technical questions about feed rates, speeds or suitable coolant for specific alloys, METAV Werkzeuge offers comprehensive advice and support tailored to your application. Their guidance helps ensure safe, optimal use of the Body Drill and maximises service life. Strong recommendation: For precise chassis and sheet‑metal work, choose MetavCUT’s Body Drill and contact METAV Werkzeuge for expert application support at info@metav-werkzeuge.com or +49 2822 7131930; WhatsApp +49 170 2837271 Designation: Body Drill / Karosseriebohrer Brand: MetavCUT SKU: 58043-FDA Material: HSS‑G (ground high‑speed steel) Diameter: 4.3 mm Spiral (Flute) Length: 13 mm Overall Length: 55 mm Tip Angle: 135° Execution: Double‑ended (double‑sided) Shank Finish: Fully ground Colour / Surface: Bright finished For Use With: Drilling Machine Model Series: Standard Line Application: Drills for Metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Body Drill by MetavCUT best used for? The Body Drill (Twist Drill) from MetavCUT is primarily used for cutting holes in metal, especially in chassis and sheet‑metal applications; its double‑ended design and HSS‑G material make it suitable for alloyed and unalloyed steels, cast irons and hard plastics where short, precise holes are required. Which three drill types exist? Commonly distinguished drill types are Metal Drills (often HSS or HSS‑G), Wood Drills, and Masonry/Concrete Drills; the Body Drill from MetavCUT belongs to the Metal Drill category and is optimised for metalworking tasks. What is a Twist Drill used for? A Twist Drill is mainly applied when machining high‑strength materials and larger hole diameters; its geometry allows straightforward re‑grinding and it withstands considerable loads, making the MetavCUT Body Drill suitable for demanding metal drilling operations. Why are Twist Drills pointed (sharpened)? The point sharpening reduces the cross‑edge at the tip of the Twist Drill, lowering friction and thus reducing required feed forces; this sharpening also improves centring in the workpiece and results in cleaner, more accurate holes when using tools such as the MetavCUT Body Drill.
4.3mm HSS-G Twist Drill DIN 1897 ,extra short, bright finished, Type N - MetavCUT
Die Kombination aus Extra kurzer Bauform und HSS-G-Schliff sorgt für bis zu 40 % schnellere Bohrungen bei deutlich geringerem Anpressdruck und reduziert so Bruchrisiko und Nacharbeit. Nutzen Sie die erhöhte Stabilität und die universelle Zylinderschaft-Aufnahme für präzise Bohrungen in dünnen Blechen und Profilen; Bestellungen und technische Beratung über Metav erfolgen direkt aus Emmerich. Spiralbohrer 4,3 mm (Typ N) – extra kurz von MetavCUT Der Spiralbohrer 4,3 mm von MetavCUT ist ein extra kurzer HSS-G Metallbohrer für Handbohrmaschinen, der besonders bei engen Platzverhältnissen und dünnwandigen Werkstücken Stabilität und schnelle Bohrfortschritte bietet. Extra kurz für mehr Stabilität beim Bohren HSS-G geschliffen für schnelleres Eindringen 135° Spitze reduziert Anbohrwiderstand Zylinderschaft für universelles Spannfutter Geeignet für legierte und unlegierte Stähle Mehr Leistung bei beengten Platzverhältnissen Die Extra kurze Ausführung reduziert die Hebelwirkung und verringert die Bruchneigung bei Handgeführten Bohrmaschinen. Durch den geschliffenen HSS-G-Werkstoff werden Bohrzeiten spürbar verkürzt, während der Kraftaufwand sinkt. Die 135° Spitze erleichtert das Anbohren in härteren Werkstoffen und minimiert das Wandern des Bohrers. Dieser Vorteil macht sich insbesondere bei dünnen Blechen und Profilen bemerkbar, wo Präzision und geringe Verformung zählen. Robuste Konstruktion und universelle Aufnahme Die Kombination aus gehärtetem HSS-G, genormter DIN 1897-Ausführung und Zylinderschaft gewährleistet eine einfache Handhabung in Standard-Dreibackenfuttern. Die kurze Spirallänge erhöht die Verdrehungsfestigkeit und eignet sich daher für Arbeiten mit begrenztem Platzangebot. Anwender profitieren von einer langlebigen Schneidegeometrie, die für Legierungsstähle, Gusseisen und Nichteisenmetalle ausgelegt ist, ohne dass bei normaler Werkstattanwendung sofort Verschleißprobleme auftreten. Praxistauglichkeit, Einsatzbereiche und Hinweise Mit einem Durchmesser von 4,3 mm fällt dieser Bohrer in den Standard-Bereich für Alltags- und Werkstattarbeiten und ist für dünne bis mittlere Bleche, Profile und Flachstahl empfohlen. Bei hohem Präzisionsanspruch empfiehlt sich vorheriges Zentrieren, da Bohrer in diesem Bereich zum Wandern neigen können. Tiefe Sacklochbohrungen über das Fünffache des Durchmessers sollten vermieden werden, da die Spanabfuhr kritisch wird. Für stärkere Drehmomente ist auf sichere Spannfutterspannung zu achten, weil der Zylinderschaft bei sehr hoher Last durchrutschen kann. Greifen Sie zur MetavCUT HSS-G Lösung für präzise Metallbohrungen und fordern Sie bei Bedarf technische Beratung per E‑Mail an info@metav-werkzeuge.com oder telefonisch unter +49 2822 7131930 Produkteigenschaften Bezeichnung: Spiralbohrer Marke: MetavCUT Serie: Standard Line Norm: DIN 1897 Artikelnummer: 56043-FDA Daten Durchmesser: 4,3 mm Gesamtlänge: 55 mm Spirallänge: 22 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (Schnellarbeitsstahl, gehärtet) Schaftausführung: Zylinder (Rundschaft, universell spannbar) Ausführung: extra kurz (mehr Stabilität, weniger Bruchneigung) Typ: Typ N (Normalspirale für Metall) Farbe: blank (hell fertigungsglanz) Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall FAQ Welche Werkstoffe lassen sich mit dem Spiralbohrer 4,3 mm von MetavCUT bearbeiten? Der Spiralbohrer 4,3 mm von MetavCUT (Standard Line, SKU 56043-FDA) eignet sich für legierte und unlegierte Stähle, Gussstahl, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe; bei sehr zähen Materialien auf geeignete Kühlung achten. Ist der Zylinderschaft des Spiralbohrers 4,3 mm für Akkubohrschrauber geeignet? Ja, der Zylinderschaft passt in gängige Dreibackenfutter von Akkubohrschraubern, jedoch ist bei hohen Drehmomenten auf feste Spannfutterspannung zu achten, da Rundschäfte bei extremer Belastung eher durchrutschen können. Warum ist die Ausführung extra kurz vorteilhaft? Die extra kurze Bauform erhöht die Verdrehungsfestigkeit und reduziert die Bruchneigung, was besonders beim Bohren in dünnwandigen Werkstücken und bei beengten Platzverhältnissen vorteilhaft ist. Welcher Spitzenwinkel ist sinnvoll für harte Werkstoffe? Der Spiralbohrer 4,3 mm verfügt über einen 135° Spitzenwinkel, der das Anbohren in härteren Werkstoffen erleichtert und das Wandern auf der Oberfläche reduziert. Gibt es spezielle Einsatzgrenzen für tiefe Bohrungen? Für den Durchmesser 4,3 mm gelten die üblichen Grenzen des Standard-Bereichs; Bohrtiefe über das Fünffache des Durchmessers wird nicht empfohlen, da die Spanabfuhr und Kühlung kritisch werden und die Bohrqualität leidet.
4.3mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Der kurze Spiralbohrer von MetavCUT kombiniert hohe Präzision, verbesserte Stabilität durch die verkürzte Auskraglänge und die scharfe HSS‑G Schneidgeometrie für bis zu 40 % schnellere Bohrvorgänge bei reduziertem Anpressdruck. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 4,3 mm – MetavCUT Standard Line Der Spiralbohrer von MetavCUT in kurzer Ausführung für präzise Metallbohrungen an stationären und handgeführten Maschinen. Spiralbohrer von MetavCUT, HSS-G geschliffen Kürzere Ausführung für erhöhte Stabilität Spitzenwinkel 135° für harte Werkstoffe DIN 338 konform für kurze Spiralbohrer Zylinderschaft, geeignet für Handbohrmaschine Kompakte Bauweise sorgt für höhere Präzision und Stabilität Die kurze Ausführung reduziert die Auskraglänge und minimiert damit Vibrationen sowie das Verbiegen beim Bohren. Daraus resultiert eine deutlich bessere Rundlaufgenauigkeit und sauberere Bohrlöcher, insbesondere in hartem Material wie legiertem Stahl. Durch die geschliffene HSS‑Geometrie lässt sich die Schnittgeschwindigkeit erhöhen und die benötigte Anpresskraft um rund 50 % reduzieren, was das Arbeiten ergonomischer und effizienter macht. Geschliffenes HSS und Geometrie: Vorteile und Hinweise Geschliffene HSS‑Bohrer (HSS‑G) bieten sehr scharfe Schneiden und hohe Maßtreue; dies führt zu saubereren Bohrbildern und präziseren Ergebnissen. Die Ausführung als geschliffener Zylinderschaft sorgt für exakten Halt im Spannfutter. Der Spitzenwinkel 135° unterstützt das Anbohren harter Werkstoffe und reduziert das Wandern des Bohrers beim Ansetzen. Beachten Sie, dass geschliffene Bohrer empfindlicher gegen Schlagbelastung sind und bei Bedarf mit Kühlung eingesetzt werden sollten. Norm, Typ und empfohlene Einsatzbereiche Die Ausführung entspricht DIN 338 für kurze Spiralbohrer und wird als Typ N (Normalspirale) klassifiziert, ideal für Metallbearbeitung in Werkstatt und Produktion. Durchmesser 4,3 mm fällt in den Standard‑Bereich, wodurch der Bohrer sowohl für stationäre Säulenbohrmaschinen als auch für handgeführte Akkubohrmaschinen geeignet ist. Typische Materialien sind legierte und unlegierte Stähle, Gusswerkstoffe, Sintereisen, Nichteisenmetalle und harte Kunststoffe. Zielgruppe und Anwendungsempfehlung Professionelle Metallverarbeiter, Instandhalter und engagierte Heimwerker profitieren von der Kombination aus Stabilität und schneller Schnittleistung. Für höchste Passungsgenauigkeit empfiehlt sich vorheriges Zentrieren mit einem Zentrierbohrer; bei allgemeinen Anwendungen kann direkt gebohrt werden. Der Bohrer eignet sich besonders, wenn präzise, wiederholbare Bohrungen in mittleren Serien oder Einzelteilen gefragt sind. Empfehlung: Für präzise Metallbohrungen empfehlen wir den MetavCUT Spiralbohrer; bei Detailfragen erreichen Sie unsere Beratung per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 45043-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Norm: DIN 338 Fakten Durchmesser: 4,3 mm Gesamtlänge: 75 mm Spirallänge: 43 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G (geschliffen) Schaftausführung: geschliffen Ausführung: kurz Typ: Typ N (Normalspirale) Farbe: blank (bright finished) Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 FAQ Für welche Materialien eignet sich der Spiralbohrer am besten? Der MetavCUT Spiralbohrer (HSS‑G) SKU 45043-FDA ist ausgelegt für legierte und unlegierte Stähle, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle sowie harte Kunststoffe und liefert in diesen Werkstoffen saubere Bohrbilder. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der kurze Spiralbohrer eignet sich für Handbohrmaschine und stationäre Maschinen; bei handgeführten Anwendungen sorgt die reduzierte Auskraglänge für bessere Stabilität und weniger Vibration. Was bedeutet HSS‑G und welche Konsequenzen hat das für die Anwendung? HSS‑G steht für geschliffen; dadurch entstehen sehr scharfe Kanten und hohe Rundlaufgenauigkeit, was besonders bei Metall vorteilhaft ist. Im Gegenzug ist der Bohrer etwas empfindlicher gegen seitliche Schläge und sollte bei Bedarf mit Kühlung betrieben werden. Warum ist ein Spitzenwinkel von 135° vorteilhaft? Ein Spitzenwinkel von 135° reduziert das Wandern beim Anbohren und verteilt die Spänedynamik günstiger bei harten Werkstoffen, wodurch das Einstechen kontrollierter und die Standzeit oft länger wird. Brauche ich einen Vorbohrer für Durchmesser 4,3 mm? Im Standard‑Bereich (2,0–13,0 mm) kann oft direkt gebohrt werden; für hochpräzise Passungen empfiehlt sich jedoch ein Zentrierbohrer, um die Querschneide zu entlasten und maximale Maßhaltigkeit zu erreichen.
4.4mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 4.4 mm, 118°, black, DIN 338, MetavCUT The Twist Drill by MetavCUT is a short HSS Type N drill for metalworking, designed for use with a Drilling Machine and Hand Drill to deliver precise, stable holes in demanding workshop applications. MetavCUT Twist Drill Type N, HSS short design 4.4 mm diameter for precise holes 118° point angle for easy centring Conforms to DIN 338 for short HSS drills Designed for drilling machine use in metal Precision and Stability for demanding metalwork Short design combined with HSS construction provides increased Stability and reduced run-out compared with longer drills. The reduced overhang inherent to the short execution minimises bending and vibration, so holes remain true in steel and non-ferrous metals. Conformity with DIN 338 guarantees standardised lengths and shank geometry, which improves compatibility with chucks and reduces setup time in professional environments. Easier centring and lower feed forces A 118° point angle reduces the size of the chisel edge and lowers friction during entry, which helps to centre the bit and requires less push force from the operator. For workshop users this means cleaner starts, fewer burrs and less chance of walk‑off on curved or coated surfaces. When working with common metal grades, the combination of the point geometry and HSS material delivers predictable cutting behaviour and longer usable life before regrinding is needed. Optimised for Type N metal drilling and machine use The Type N normal spiral geometry is the classic choice for metal drilling and was selected here to balance chip evacuation and cutting efficiency. This Twist Drill is specified for Drilling Machine operation and is equally suited for handheld machines where a short shank improves control. HSS manufacturing assures elasticity that reduces the risk of breakage on diameters below 6 mm while maintaining cutting performance in alloyed and unalloyed steels, cast iron and many non‑ferrous materials. Who benefits and typical applications Maintenance technicians, toolroom operatives and metal fabricators benefit from the combination of Precision and durability offered by this short HSS Type N drill. Typical applications include through and blind holes in sheet metal, plate and machined components where stability and repeatable hole quality are essential. The black surface finish assists visual inspection and handling in busy workshop conditions. MetavCUT recommends this Twist Drill Type N for precise metal drilling — for personalised technical advice METAV Werkzeuge provides expert support: info@metav-werkzeuge.com | Tel +49 2822 7131930 | WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand: MetavCUT SKU: 40044-FDA Diameter: 4.4 mm Point angle: 118° Type: Type N Material: HSS Execution: short Spiral length: 47 mm Overall length: 80 mm Colour: black Application: Drills for metal For drilling machine: Drilling Machine Standard: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill from MetavCUT Type N best used for? The MetavCUT Twist Drill Type N is primarily used for metalworking tasks; it is ideal for drilling alloyed and unalloyed steel, cast iron and many non‑ferrous metals when operated on a drilling machine or by skilled handheld use. Its short HSS design improves stability and accuracy in workshop operations. Which three drill types exist? Three common drill types are Metal drills, Wood drills and Stone/Concrete drills. The MetavCUT Twist Drill Type N belongs to the metal drill category and is optimised for those materials. For what is a Twist Drill generally used? A Twist Drill is mainly applied when machining high‑strength materials and for larger hole diameters; its shape makes it straightforward to resharpen and it withstands significant loads during cutting. It is often chosen where durability and regrindability are required.
4.4mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Typ N) — short HSS‑E Metal Drill, 4.4 mm, 135° tip, 5% cobalt‑alloyed The Twist Drill (Typ N) is a short HSS‑E metal drill designed for precise machining with a 135° point angle and a fully ground shank for secure chucking. Short design for higher stability 135° tip for hard and alloyed steels 5% cobalt‑alloyed HSS‑E for increased red‑hardness Fully ground flutes for accurate, clean holes Conforms to DIN 338 for short twist drills Precision and Stability for Demanding Metalwork A short HSS‑E drill of this design delivers notably greater stability during drilling because the reduced overhang minimises bending and vibration. The combination of a 4.4 mm diameter with a 47 mm flute length and overall length of 80 mm results in a compact tool that keeps the cutting geometry close to the chuck, improving concentricity and repeatable hole quality when used in a compatible Drilling Machine or stationary set‑up. This construction is ideal for work that requires tight tolerances and reliable hole positioning. Optimised for Hard Materials and Clean Holes Thanks to the 135° point angle and the 5% cobalt‑alloyed HSS‑E substrate, the drill penetrates harder and alloyed steels more effectively than standard HSS tools. The fully ground flute geometry produces very sharp cutting edges and high roundness, which leads to cleaner holes with less burring. Users should note that the grinded version offers excellent precision but can be more brittle than roll‑formed variants; appropriate coolant and stable clamping are recommended to extend tool life during high‑performance drilling. Designed to Meet DIN 338 Requirements and Workshop Needs Manufactured to the DIN 338 standard for short twist drills with a cylindrical shank, this tool follows established size and tolerance criteria that support interchangeability and predictable performance. The Type N spiral geometry represents the classic metal‑drill profile, suitable for materials such as alloyed and unalloyed steel, cast iron, non‑ferrous metals and certain plastics. The short format is particularly suited to precision workshop tasks where reduced run‑out and minimal deflection are priorities. Who benefits from this short HSS‑E drill? Engineers, toolroom technicians and metalworkers who require accurate, repeatable holes in tougher materials will find this drill especially useful. Its compact design and fully ground shank make it a strong choice for setups where rigidity matters—such as jig bores, component finishing and jobs on vertical or radial drilling machines. For less rigid hand‑held applications, ensure a secure chuck grip and moderate feeds to avoid undue stress on the cutting edge. Empfehlung von MetavCUT: For precise metal drilling tasks choose the MetavCUT short Twist Drill in HSS‑E; for further advice on suitability or complementary tooling contact METAV Werkzeuge — we provide expert consultation and technical support via eMail, phone and WhatsApp Email: info@metav-werkzeuge.com • Tel: +49 2822 7131930 • WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill (Spiralbohrer), short, Type N, 4.4 mm, 135° Marke/Hersteller: MetavCUT SKU: 47044-FDA Material: HSS-E (5% cobalt-alloyed) Durchmesser: 4.4 mm Spiralänge (Flute Length): 47 mm Gesamtlänge (Overall Length): 80 mm Spitzenwinkel (Point Angle): 135° Schaft-Ausführung: fully ground (geschliffen) Ausführung: short (kurz) Anwendung: Drills for metal / Bohrer für Metall Norm: DIN 338 Für Bohrmaschine: Drilling Machine (Handbohrmaschine) Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) mainly used for? The MetavCUT Twist Drill (Type N) is primarily applied to the machining of high‑strength materials and larger drill diameters; its form allows straightforward re‑grinding and it endures higher mechanical loads, making it suitable for demanding metalworking tasks. Which three drill types are there? There are three common drill categories: metal drills, wood drills and stone/concrete drills. Why is a twist drill pointed (ausgespitzt)? The pointing reduces the cross‑cut at the drill tip, which significantly lowers friction and thus the required feed forces; at the same time the sharper point improves centring of the drill in the workpiece.
4.4mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
Body Drill Twist Drill — 4.4 mm, 135°, Double-Sided, Bright Finished, HSS-G by MetavCUT A Body Drill twist drill designed for precision metalworking, ideal for drilling in automotive panels and thin sheet applications. Double-ended reversible design for extended use HSS-G material for precise, clean metal holes 135° tip optimized for harder materials Fully ground shank for excellent concentricity Short, robust profile for sheet-metal and bodywork Durable HSS-G construction for precise metalwork The Body Drill from MetavCUT is manufactured in HSS-G, a ground high-speed steel grade that delivers high precision and sharp cutting edges. Ground flute geometry provides superior hole quality and repeatable performance when machining alloys and steels. Because the flutes are ground rather than rolled, the result is a cleaner cutting geometry and improved concentricity, which reduces vibration and leads to consistently accurate holes. Double-sided design that extends tool life Engineered as a double-sided (double-ended) twist drill, this bit offers practical redundancy: when one tip becomes dull, the tool can be reversed and the second cutting end used, effectively doubling usable life for many workshop scenarios. The compact, short profile makes it particularly suited to tight spaces in automotive bodywork and thin-sheet operations, where a stable, robust tool is required for repeatable drilling. 135° tip and application guidance for harder materials The 135° tip angle reduces initial cutting forces and improves centring when working with harder materials such as stainless steel or tempered alloys. For users less familiar with drill geometry: a larger tip angle flattens the cutting edge, slowing initial penetration but improving stability and reducing burr formation. This makes the bit well suited for drilling in both alloyed and unalloyed steels, cast irons, and some hard plastics when used with appropriate cutting fluid and moderate speeds. Compatibility, handling and recommended use The bit features a fully ground shank designed for secure chucking in standard Drilling Machines and Hand Drills. Its short overall length and ground shank minimise runout, improving precision in repetitive tasks. For best results, use cooling lubricant when drilling tough steels and avoid excessive pecking on very hard materials to reduce the risk of breakage. This tool is aimed at bodywork professionals, metal fabricators, and maintenance technicians who require reliable performance in demanding conditions. MetavCUT’s HSS-G double-sided Body Drill is recommended for demanding metalworking tasks — for personalised technical advice or to confirm suitability for specific applications, contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com | ☎️ +49 2822 7131930 | ✔️ WhatsApp +49 170 2837271 Designation: Body Drill Brand: MetavCUT SKU: 58044-FDA Diameter: 4.4 mm Point angle: 135° Version / Execution: Double-sided Colour / Finish: Bright finished Material: HSS-G Shank execution: Fully ground Spiral length (flute length): 13 mm Overall length: 55 mm For Drilling Machine: Drilling Machine Application: Drills for metal Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Body Drill twist drill is primarily used for machining high-strength materials and larger hole diameters in metalworking. Twist drills of this type are often applied to alloyed and unalloyed steels, cast steel, cast iron, sintered iron, non-ferrous metals and hard plastics. Their geometry makes them relatively easy to grind and able to withstand significant loads. Which three drill types exist? Three common categories are metal drills, wood drills, and stone/concrete drills. The MetavCUT Body Drill belongs to the metal-drill category, designed specifically for metalworking tasks and differing in geometry and material from wood or masonry bits.
4.4mm HSS-G Twist Drill DIN 1897 ,extra short, bright finished, Type N - MetavCUT
Twist Drill — 4.4 mm, 135°, Type N, extra short, Bright finished, HSS‑G, DIN 1897 The Twist Drill Type N is an extra‑short, high‑performance HSS‑G drill bit designed for precise metal drilling with hand Drilling Machines and in confined working spaces. Extra-short design for enhanced stability 4.4 mm diameter for precise holemaking 135° point for hard materials like stainless steel Cylindrical shank fits standard three-jaw chucks HSS-G material for increased wear resistance Greater control where space is limited The extra‑short construction reduces overhang and gives noticeably more stability during manual drilling, which lowers the risk of walking or breakage when working in narrow or thin components. This shortened geometry is especially advantageous when drilling into sheet metal, profiles or thin‑walled parts, since the reduced overall length makes the bit easier to guide and prevents unwanted bending under load. Faster drilling with less force A ground HSS‑G cutting geometry enables significantly improved cutting performance: users can expect up to 40% faster drilling while requiring roughly 50% less feed force compared with conventional HSS bits. This means reduced operator fatigue and more efficient machining cycles when producing holes in alloyed and unalloyed steel, cast materials, sintered iron and hard plastics. Engineered for demanding metalwork The 135° point angle is optimised for harder materials and short‑run accuracy: it reduces initial axial deflection and shortens the time to penetrate hard surfaces such as stainless steel. As a Type N normal‑spiral twist drill, the bit is primarily intended for metalworking applications and offers a well‑balanced flute geometry for reliable chip evacuation under typical workshop conditions. Practical fit and recommended use With a cylindrical shank, the bit fits universally in standard three‑jaw chucks, making it suitable for hand and angle Drilling Machines where convenience and universality matter. Professionals and advanced DIY users who require robust, short‑length drilling tools for maintenance, assembly or fabrication will find the bit particularly useful. If uncertain whether this tool meets specific requirements, METAV Werkzeuge offers competent technical advice and support via email, phone or WhatsApp. We recommend the MetavCUT Twist Drill for precision metalworking tasks — for tailored guidance or further technical details contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 (WhatsApp +49 170 2837271) Designation: Twist Drill Brand: MetavCUT SKU: 56044-FDA Diameter: 4.4 mm Point angle: 135° Type: Type N Execution: extra short Finish: bright finished Shank: cylindrical Material: HSS-G Standard: DIN 1897 Spiral length: 22 mm Total length: 55 mm For Drilling Machine: Drilling Machine Application: Drills for metal Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and which workplaces suit the MetavCUT Twist Drill Type N? The MetavCUT Twist Drill Type N is primarily used for drilling metal; it is best applied in workshops and on assembly tasks where precise, stable holes are required. The extra‑short design makes this Twist Drill well suited to thin materials and confined spaces while the HSS‑G grade supports drilling in alloyed and unalloyed steels as well as cast materials. Which three drill types are common and how does the Twist Drill compare? Common drill types are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill (a metal drill) is optimised for metal applications and differs from wood or masonry drills in flute geometry, point angle and material, which together ensure cleaner holes and better durability when working with metals.
4.4mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill – Short HSS‑G, 4.4 mm, 135° (Typ N), Bright Finished, DIN 338, Fully Ground Shank — MetavCUT The Twist Drill is a short precision drill for metalworking, designed for use with drilling machines and hand drills to deliver stable, accurate holes in hard materials. Short design for increased stability and precision HSS‑G material with CNC ground flute geometry 135° tip for improved entry in hard steels Fully ground shank for high concentricity Conforms to DIN 338 for short cylindrical twist drills Precision and reduced deflection for demanding metalwork The short construction of this Twist Drill delivers higher stability and significantly reduced deflection compared with longer geometries. That shorter overhang improves hole accuracy under load and lowers the risk of breakage during tough cuts, making it particularly suitable for precise operations in workshops and industrial environments. The combination of reduced vibration and a compact length supports consistent hole quality on difficult materials. Faster cutting and easier feed thanks to ground HSS geometry Equipped with HSS‑G material and ground flute geometry, this tool offers cleaner cutting edges and excellent chip evacuation. Ground drills (HSS‑G) typically produce sharper cutting lips and better runout, which translates to faster penetration and reduced feed forces compared with rolled variants. For users unfamiliar with the term: ground means the flutes and cutting geometry are machined by grinding, resulting in very sharp, precise edges ideal for metal. Targeted application: engineered for metals and workshop use Designed as a Type N normal spiral, the Twist Drill is aimed at operations in alloyed and unalloyed steels, cast iron, sintered materials, non‑ferrous metals and hard plastics. Use with stationary drilling machines or robust hand drills is recommended; the short length suits jigs, fixtures and confined setups. Professionals and serious hobbyists who require repeatable, high‑quality holes in demanding substrates will benefit most from this tool. DIN 338 conformity and dimensional data for reliable integration Manufactured to DIN 338 standards for short cylindrical twist drills, the tool ensures compatibility with industry expectations for dimensions and performance. Key dimensions: Diameter 4.4 mm, Spiral Length 43 mm, Overall Length 75 mm and Tip Angle 135°. The fully ground shank promotes excellent concentricity in chucks, helping to maintain accuracy across repeated operations and simplifying tool changes on CNC or conventional machines. We strongly recommend the MetavCUT short HSS‑G Twist Drill (Type N) for precision metalworking — for individual technical advice or to check suitability for specific applications contact METAV Werkzeuge at info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 45044-FDA Diameter: 4.4 mm Spiral length: 43 mm Overall length: 75 mm Tip angle: 135° Type: Typ N Execution: short Material: HSS‑G Shank: fully ground Surface/Finish: bright finished Application: Drills for metal Standard: DIN 338 For drilling machine: Drilling Machine / Hand Drill Packaging unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the recommended use for the MetavCUT Twist Drill (Type N)? The MetavCUT Twist Drill (Type N) is primarily intended for metalworking applications; it excels when drilling alloyed and unalloyed steels, cast and sintered irons, non‑ferrous metals and hard plastics in both workshop and industrial settings. Can the MetavCUT Twist Drill be used in hand drills and drilling machines? Yes, the MetavCUT Twist Drill (Type N) is suitable for use in sturdy hand drills as well as stationary drilling machines; its short design and fully ground shank ensure good stability and concentricity in common chucks. For what is a Twist Drill used? A Twist Drill is mainly used for machining high‑strength materials and larger hole diameters; its ground geometry makes it easy to sharpen and capable of withstanding higher loads. Which three drill types exist? The three main drill types are metal drills, wood drills and stone/concrete drills. Why are Twist Drills pointed? The pointing reduces the cross‑cut at the tip, which lowers friction and decreases the required feed force while improving centring of the tip in the Workpiece. Can you drill wood with a Twist Drill? A metal Twist Drill can be used in wood, but guidance and finish are inferior compared to dedicated wood drills; however, metal drills are easier to resharpen and exhibit less self‑feed. At what drilling depths is the Twist Drill most used? For through‑hole drilling in solid material, Twist Drills are the standard choice; they are most commonly used up to diameters around 20 mm and drill depths up to approximately 100 mm. Is HSS or HSSE better? The general belief that HSSE steels are always superior to HSS is not universally correct; decisions should be based on specific working conditions to determine whether the higher cost of HSSE is justified.
4.5mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill Type N — 4.5 mm, 118° Tip Angle, Short, Black, HSS, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS metal drilling tool designed for precise, stable holes in metal components using standard Drilling Machines. MetavCUT Twist Drill Type N short for metal drilling Diameter 4.5 mm for accurate hole guidance 118° Tip Angle for reliable centring on soft metals HSS construction for toughness and wear resistance Complies with DIN 338 short-length specification Consistent Precision and Reduced Vibration for Metalworking The short design of this Twist Drill provides improved stability and reduced deflection compared with longer drills, so holes remain true to size and position. Because the exposed length beyond the Chuck is reduced, bending moments decrease and the tool transfers cutting forces more effectively to the machine. This results in fewer rework cycles and a steady hole finish when machining components from alloyed or unalloyed steel. For workshop applications where repeatable accuracy matters, the short execution is a practical advantage. Robust Material Choice for Long Tool Life Manufactured from HSS (High Speed Steel), this Type N Twist Drill balances hardness and toughness for sustained use in metal. HSS resists softening at elevated temperatures, which helps maintain cutting geometry during continuous operation. For users less familiar with the term: HSS stands for High Speed Steel, a standard tool material that performs well on steel, cast iron, non-ferrous metals and many plastics. The result is longer service life and fewer tool changes on production or maintenance tasks. Designed for Metal Drilling, Suited to Hand and Machine Work As a Type N normal-spiral geometry, the drill is optimised for metalworking tasks on Drilling Machines and compatible hand-operated equipment where controlled feed is applied. The 4.5 mm Diameter and 118° Tip Angle are chosen to give reliable centring and chip formation in a broad range of metals; the geometry supports common workshop procedures such as pilot hole drilling and sequential operation with larger diameters. This tool is particularly effective when stability and precision are required rather than deep-reach drilling. Practical Handling, Sharpening and Application Notes Short Twist Drills are easier to keep concentric in the Chuck and are less prone to chatter; this makes them well suited for repeatable workshop tasks and for operators seeking consistent results. If reconditioning is needed, the normal spiral and HSS material allow straightforward resharpening on conventional tool grinders, prolonging service life. For safe, efficient use, maintain steady feed, adequate cutting speed and appropriate lubrication when machining steel to reduce heat and extend tool life. METAV Werkzeuge offers expert advice if application specifics require tailored recommendations. We recommend MetavCUT's short Type N Twist Drill for demanding metal applications — for competent, personalised support contact METAV Werkzeuge via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 or WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40045-FDA Type: Type N Diameter: 4.5 mm Tip Angle: 118° Material: HSS Execution: short Spiral Length: 47 mm Overall Length: 80 mm Colour: black Application: Drills for metal Standard: DIN 338 Suitable For: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? A MetavCUT Twist Drill (Type N) is principally applied to the machining of high-strength materials and larger hole diameters; its form allows economical sharpening and it endures higher loads, making it suitable for demanding metalwork. Which three drill types exist? Common categories are Metal Drill (like this MetavCUT Twist Drill), Wood Drill, and Stone/Concrete Drill, each designed with geometry and materials suited to their target substrates. Why are Twist Drills pointed? Pointing reduces the cross-cut at the tip of the Twist Drill which lowers friction and thereby reduces required feed forces; in addition the sharpened tip improves centring in the workpiece. Can you drill wood with a Twist Drill? A Metal Drill such as the MetavCUT Type N can be used in wood, but guidance and finish are inferior to purpose-designed wood bits; however, metal drills are easier to resharpen and show less self-feeding. For which drilling depths is the Twist Drill most used? A through-hole in solid stock is typically produced with a Twist Drill; for diameters up to around 20 mm and depths up to about 100 mm, the Twist Drill is the most commonly applied tool. What is better, HSS or HSSE? The general assumption that HSSE is always superior to HSS is incorrect; assess working conditions and whether the higher cost of HSSE is justified for your specific MetavCUT drilling tasks before choosing.
4.5mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill Type N — 4.5 mm, 135° point angle, short execution, 5% cobalt-alloyed, HSS‑E, DIN 338 The Twist Drill Type N is a short HSS‑E metalworking bit designed for stable, precise drilling in hard materials with a 135° Point Angle and a fully ground shank for high concentricity. Short Twist Drill 4.5 mm for precise metalwork 135° Point Angle for hard materials like stainless steel 5% cobalt-alloyed HSS‑E for higher heat resistance Fully ground shank for excellent concentricity and finish Conforms to DIN 338 for short Twist Drills Designed for precision in metalworking and stable drilling Short design delivers a tangible benefit: reduced overhang means less deflection and improved accuracy when working with tough materials. The compact geometry of this short Twist Drill supports higher rigidity, so holes remain rounder and positional tolerances are easier to achieve. This is particularly relevant when machining alloyed or unalloyed Steel, Cast Iron and other Metals where tool chatter or bending would otherwise impair results. The result is a reliable Tool that helps maintain Process stability in both bench and machine applications. Robust Material and geometry for demanding applications Manufactured from HSS‑E with 5% cobalt-alloyed composition, the bit resists softening under elevated temperatures and keeps cutting edges sharper for longer life. The 135° Point Angle reduces entry forces on hard materials and improves centring on tougher Surfaces such as Stainless Steel. Being a Type N normal spiral, the geometry balances chip evacuation and edge strength—explainable: HSS‑E adds hot hardness, cobalt increases wear resistance; together they extend tool life under intermittent or high-load drilling. Machine compatibility and standards for reproducible results Designed according to DIN 338 for short Twist Drills, this Tool fits standard chuck systems and is intended for use in a drilling machine or hand drilling Machine where increased stiffness is required. The fully ground Shank ensures superior concentricity and runout characteristics, which supports precision fixtures and measured machining. For operators, this means fewer rejections and easier post-process handling when producing repeatable holes in metal components. Practical guidance, target users and safe operation Workshop professionals, maintenance technicians and toolroom users benefit most from this short Twist Drill due to its stability and suitability for harder metals. Use moderate cutting speeds, appropriate coolant for metalworking, and firm clamping to exploit the Drill’s advantages; avoid excessive overhang despite the short form. The fully ground flute geometry is explained by its manufacturing: grinding produces very sharp cutting edges and high Roundness, but requires careful handling to avoid brittle fractures—especially at very small diameters or under unsupported conditions. Strong recommendation: choose the MetavCUT Twist Drill Type N for precise metal drilling — for personalised technical advice contact METAV Werkzeuge; Email: info@metav-werkzeuge.com; Phone: +49 2822 7131930; WhatsApp: +49 170 2837271 Technical Data Designation: Twist Drill Marke: MetavCUT SKU: 47045-FDA Diameter: 4.5 mm Total Length: 80 mm Spiral Length: 47 mm Point Angle: 135° Typ: Type N Execution: short Material: HSS‑E Colour / Alloy: 5% cobalt-alloyed Shaft Finish: fully ground For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Standard Line Norm: DIN 338 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the best use for the Twist Drill Type N from MetavCUT? The MetavCUT Twist Drill Type N is primarily intended for drilling Metal; it excels in machining high-strength and alloyed steels thanks to its short design, which increases stability and reduces bending during operation. Can the MetavCUT Twist Drill Type N be used with a hand drilling machine? Yes, the MetavCUT Twist Drill Type N can be used in a hand drilling Machine, but optimal results are achieved with a well-secured workpiece and steady feed to minimise stress on the short, fully ground flute geometry. For what is a Twist Drill used? A Twist Drill is mainly applied when working on high‑strength materials and large diameters; its form is easy to regrind and withstands higher loads while remaining suitable for precision metal drilling. Which three drill types exist? The three main drill types are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the Metal drill category. Why are Twist Drills pointed? Pointing the Twist Drill reduces the secondary cutting edge at the tip, which lowers friction and the required feed forces while improving centring of the Drill in the Workpiece. Can a Twist Drill be used to drill wood? A Metal drill such as the MetavCUT Twist Drill Type N can be used in Wood, but guidance and hole finish are inferior compared with dedicated Wood drills; however, Metal drills are easier to regrind and have less self‑feeding tendency. At which drilling depths is the Twist Drill most used? A drilling operation into solid material is typically performed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm, the Twist Drill is the most commonly used tool.
4.5mm HSS-G Body Drill ,double sided, bright finished - MetavCUT
MetavCUT Body Drill (Karosseriebohrer) — Twist Drill for Drilling Machine, 4.5 mm Ø, 135° tip, HSS‑G, double‑sided, bright finished, fully ground shaft The MetavCUT Body Drill is a double‑sided Twist Drill engineered for precise metalworking on drilling machines, combining HSS‑G cutting performance with a 135° tip for hard materials. Double‑ended design for two usable tips High‑speed HSS‑G for precise metal drilling 135° tip for harder materials like stainless steel Fully ground shank for high roundness accuracy Bright finished surface for improved corrosion resistance Engineered for hard metals with lower feed force and fast cutting The MetavCUT Body Drill uses HSS‑G material to achieve high cutting performance in demanding conditions. The ground geometry results in very sharp cutting edges and improved roundness, which can lead to up to 40% faster drilling and approximately 50% less required feed force compared with conventional HSS drills. This makes the tool particularly efficient when working with alloyed and unalloyed steels, cast steels and other hard metals, delivering clean holes with minimal burr formation. Practical double‑ended design and robust shaft for workshop use A double‑sided or double‑ended Twist Drill offers clear workshop advantages: two usable tips in one short, stable body. If one tip becomes blunt, the drill can be reversed and the opposite tip used, effectively providing two tools in a single bit. The fully ground shaft and bright finished surface contribute to high concentricity and easier handling in chucks, while the compact overall length increases stability when drilling thin sheets or rivet holes. Best applications and dimensional clarity for correct tool selection Designed for metalworking, this Body Drill is suitable for Drilling Machines and hand drills where precision is required. Key dimensions are a diameter of 4.5 mm, a spiral/ flute length of 13 mm and an overall length of 58 mm. Typical materials include cast iron, sintered iron, tempered cast, non‑ferrous metals and hard plastics; the 135° tip reduces thrust and improves centring in tougher substrates. Choose appropriate speeds and coolant when machining harder alloys. Simple recommendations to prolong life and improve hole quality To avoid chipping or breakage, use moderate speeds and adequate cooling when working with hard materials, and secure the workpiece to eliminate runout. The ground flute geometry improves chip evacuation, but the short spiral length is optimised for through‑holes and thin‑section drilling rather than deep boring. For repeatable, high‑quality results, prefer stationary setups with coolant and verify feed rates to match the stated benefits of reduced feed force. Strong recommendation: the MetavCUT Body Drill is ideal for professionals seeking durable, precise metal drilling — for further technical advice or assistance contact METAV Werkzeuge for expert consultation via email info@metav-werkzeuge.com, phone +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Body Drill (Karosseriebohrer) Brand: MetavCUT SKU: 58045‑FDA Diameter: 4.5 mm Tip angle: 135° Material: HSS‑G Execution: double‑sided Colour / Finish: bright finished Intended for: Drilling Machine / Hand Drill Spiral length: 13 mm Overall length: 58 mm Shaft execution: fully ground Model series: Standard Line Application: Drills for metal Packaging unit: 10 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can the MetavCUT Body Drill be used in a handheld drill or is a drilling machine required? The MetavCUT Body Drill is suitable for use in both a drilling machine and a robust hand drill, but best results—especially in hard or alloyed metals—are achieved with a stable drilling machine and appropriate coolant to reduce heat and prevent breakage. Why choose a double‑sided Twist Drill like the MetavCUT Body Drill? A double‑sided Twist Drill provides two usable tips in one tool; when one end becomes blunt it can simply be reversed, offering greater cost efficiency and reduced downtime in workshops handling thin sheets or riveted assemblies. For what is a Twist Drill used? A Twist Drill is mainly applied to machining high‑strength materials and larger drill diameters; its design allows relatively easy re‑grinding and it withstands higher loads, making it especially common for metalworking tasks and holes in sheet or structural components. Which three drill types exist? There are three common drill families: metal drills, wood drills and masonry/concrete drills. Each type is optimised for material‑specific geometry and cutting behaviour.
4.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Der geschliffene HSS‑G Spiralbohrer verbindet hohe Schnittgeschwindigkeit mit extra langer Bauart: Bis zu 40 % schnelleres Bohren und 50 % geringerer Anpressdruck reduzieren Arbeitszeit und Ermüdung. Die 125 mm Spirallänge ermöglicht tiefe, saubere Bohrungen in Metall. Bestellen Sie den Spiralbohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer HSS‑G extra lang von MetavCUT Der Spiralbohrer HSS‑G extra lang für tiefe Metallbohrungen in legierten und unlegierten Stählen sowie Gusswerkstoffen. Extra lange Bauart für tiefe Bohrungen Geschliffen HSS‑G für scharfe Kanten und Präzision 125 mm Spirallänge, verbessert Spänetransport Spitzenwinkel 135° für harte Werkstoffe DIN 1869 konform, geeignet für Stahl und Guss Schnelleres Bohren, weniger Kraftaufwand Der geschliffene HSS‑G Werkstoff reduziert Reibung und ermöglicht ein bis zu 40 % schnelleres Arbeitsfortschreiten bei gleichzeitig 50 % geringerem Anpressdruck im Vergleich zu konventionellen HSS‑Bohrern. Das Resultat ist weniger Werkzeugverschleiß und eine höhere Produktivität in Serien‑ und Einzelarbeiten. Für Anwender bedeutet das konkret kürzere Bearbeitungszeiten und geringere körperliche Belastung bei wiederholten Bohrungen. Extra Länge sorgt für Zugänglichkeit bei tiefen Bohrungen Mit einer Gesamtlänge von 185 mm und einer aktiven Spirallänge von 125 mm eignet sich dieses Extra‑Lang‑Design speziell für tiefe Sackloch‑ und Durchgangsbohrungen, bei denen Standardlängen nicht ausreichen. Die verlängerte Arbeitslänge verbessert den Späneaustrag in tiefen Bohrungen und reduziert das Nachschneiden. Dennoch empfiehlt sich bei sehr langen Auskragungen eine ruhige Führung oder der stationäre Einsatz zur Vermeidung von Abweichung. Geometrie und Material für harte Werkstoffe Die 135° Spitzengeometrie ist optimal abgestimmt auf härtere Werkstoffe wie legierten Stahl und Edelstahl, während die Norm DIN 1869 die Eignung für anspruchsvolle Metallbearbeitung bestätigt. Der geschliffene Schaft liefert hohe Rundlaufgenauigkeit und saubere Bohrbilder, verlangt jedoch vorsichtigen Umgang: Bei tiefen oder sehr harten Materialien ist Kühlung und langsamer Vorschub empfehlenswert, um thermische Überlastung und Bruchrisiken zu minimieren. Einsatzempfehlung für Werkstatt und Montage Mit einem Durchmesser von 4,5 mm bewegt sich der Bohrer im Standard‑Bereich und ist für den Einsatz in Werkstatt, Montage und mit Handbohrmaschinen geeignet. Für hochpräzise Passungen empfiehlt sich Voranpunkten mit einem Zentrierbohrer, um Abwandern zu vermeiden. Bei tiefen Bohrungen oder häufiger Nutzung erhöht eine stationäre Aufnahme mit laufender Kühlung die Standzeit erheblich und sorgt für konstante Bohrqualität. Wählen Sie den MetavCUT HSS‑G Spiralbohrer in Extra‑Länge für anspruchsvolle Metallbohrungen und sichern Sie sich präzise Ergebnisse — bei Fragen kontaktieren Sie uns per E‑Mail info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 oder via WhatsApp +49 170 2837271. Technische Daten Artikelnummer: 32045-FDA Marke: MetavCUT Serie: Standard Line Fakten Durchmesser: 4,5 mm Gesamtlänge: 185 mm Spirallänge: 125 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G Norm: DIN 1869 Ausführung: extra lang Schaftausführung: geschliffen Verpackungseinheit: 10 Farbe: Blank Anwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine SKU: 32045-FDA FAQ Für welche Materialien eignet sich dieser Spiralbohrer am besten? Der MetavCUT Spiralbohrer HSS‑G (SKU 32045-FDA) ist ausgelegt für legierte und unlegierte Stähle, Grauguss, Gusseisen, Temperguss, Nichteisenmetalle sowie Hartkunststoff und erreicht sichere Ergebnisse bis circa 1000 N/mm². Ist der Bohrer für Handbohrmaschinen geeignet? Ja, der 4,5 mm Bohrer fällt in den Standard‑Bereich und kann mit Handbohrmaschinen eingesetzt werden; bei tiefen Löchern oder erhöhter Präzision empfiehlt sich jedoch eine ruhige Führung oder stationäre Aufnahme. Welche Vorteile bietet die geschliffene Schaftausführung? Die geschliffene Schaftausführung sorgt beim MetavCUT Spiralbohrer für hohe Rundlaufgenauigkeit und sehr scharfe Schneiden, was zu sauberen, präzisen Bohrbildern führt; dafür ist vorsichtiger Umgang und Kühlung wichtig, um Bruchrisiken zu minimieren. Brauche ich Vorbohren für 4,5 mm Durchmesser? Für allgemeine Anwendungen kann direkt gebohrt werden; bei besonders präzisen Passungen empfiehlt sich Voranpunkten mit einem Zentrierbohrer, um ein Wandern der Bohrung zu verhindern. Wie beeinflusst die Spitzengeometrie die Anwendung? Der 135° Spitzenwinkel des MetavCUT Spiralbohrers verkürzt die Anbohrzeit in härteren Werkstoffen und reduziert den Schneidendruck, wodurch sich saubere Einstiche und weniger Ausriss ergeben.
4.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra Long HSS‑G Twist Drill, 4.5 mm, 135°, Bright Finished, Fully Ground, DIN 1869 (MetavCUT) The Twist Drill is an extra long HSS‑G drill designed for deep metal drilling with a 135° point angle for reliable centring and efficient penetration. Extra long design for deep hole access HSS‑G fully ground for precise bore quality 135° point angle for harder materials Bright finished surface for corrosion protection Compatible with Handheld Drilling Machines Faster, cleaner metal drilling for demanding tasks The HSS‑G composition of this Twist Drill delivers a combination of hardness and toughness optimised for metalworking. Because the flutes are CNC ground rather than rolled, the tool achieves high roundness accuracy and razor‑sharp cutting edges, which produce cleaner Holes and extend tool life under appropriate cooling. One major benefit is the documented performance gain: the ground HSS design can drill up to 40% faster and requires up to 50% less feed force compared with conventional HSS variants, making it particularly efficient for alloys and unalloyed steels. Designed for deep-hole applications and accessibility With a Spiral Length of 160 mm and an Overall Length of 235 mm, this extra long Twist Drill reaches depths that standard lengths cannot. The extended geometry is ideal when drilling in confined or hard‑to‑reach positions, or when a longer reach is needed from a Drilling Machine or handheld device. The tool’s bright finished surface eases chip evacuation and reduces surface friction during long penetration depths, supporting stable, repeatable results. Optimised geometry for hard materials and precision The 135° Point Angle of this Twist Drill reduces walking and improves centring when working with harder Metals such as stainless steel or cast materials. The fully ground shank ensures superior concentricity in chucks, translating into better hole tolerances and lower run‑out. For users needing precision bores in components, this geometry offers a clear advantage: faster initial engagement and a reduced tendency for the tool to skid during the start of the cut. Practical guidance: use, cooling and sharpening Although the ground HSS design gives excellent cutting performance, users should note the material can be more brittle than rolled types and benefits from correct application. Apply steady cutting speeds, adequate coolant and moderate feed to avoid chipping. The Twist Drill is easier to regrind when required, and the sharpened geometry reduces radial forces, meaning less effort during re‑sharpening. For stationary machine work and workshop conditions, cooling and secure clamping are recommended to maximise service life. For demanding deep‑hole metalwork choose the MetavCUT Twist Drill with its extra long HSS‑G design — METAV Werkzeuge provides expert advice and support: eMail info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 33045-FDA Durchmesser: 4.5 mm Spitzenwinkel: 135° Ausführung: Extra long Farbe: Bright finished Material: HSS‑G Schaft Ausführung: Fully ground Gesamtlänge: 235 mm Spirallänge: 160 mm Norm: DIN 1869 Anwendung: Drills for metal / For Drilling Machine Modellserie: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the Twist Drill (MetavCUT Twist Drill) be used on? The MetavCUT Twist Drill is intended primarily for metalwork; its HSS‑G composition and 135° point angle make it suitable for legierte und unlegierte Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle and hard plastics where precision and durability are required. Is the MetavCUT Twist Drill suitable for handheld drilling machines? Yes, the MetavCUT Twist Drill can be used with a Handheld Drilling Machine, but due to its extra long geometry and the ground HSS design, stable clamping, reduced feed forces and adequate cooling are advised to prevent chipping and ensure safe operation. For what is a Twist Drill used? A Twist Drill is mainly applied when machining high‑strength materials and larger bore diameters; the form is easy to regrind and endures higher loads, which is why the MetavCUT Twist Drill is chosen for demanding metalworking tasks. Which three drill types exist? The three main drill types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for such applications. Why are Twist Drills sharpened? Sharpening reduces the cross‑edge at the tip of the Twist Drill, which lowers friction and therefore decreases required feed forces, while improving centring and initial penetration of the MetavCUT Twist Drill. Can the MetavCUT Twist Drill be used to drill wood? A metal drill can be used in wood, but guidance and finish are inferior compared with dedicated wood bits; the MetavCUT Twist Drill can cut wood but may show poorer tracking and a less clean hole while being easier to regrind and exhibiting lower self‑feed characteristics. At which drilling depths is the Twist Drill most commonly used? A through‑hole in solid material is commonly executed with a Twist Drill. For diameters up to 20 mm and depths up to 100 mm, the Twist Drill is the most frequently used tool, and the extra long MetavCUT variant is especially useful for deeper requirements. What is better, HSS or HSSE? The general belief that HSSE is always superior to HSS is not universally true. Consider whether your working conditions actually justify the higher purchase cost of HSSE before deciding; the MetavCUT HSS‑G grade may already meet many demanding applications.
4.5mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Drill for Metal (Ø 4.5 mm, 135° Point, Extra Long, Bright Finished, HSS-G, DIN 1869) The Twist Drill is an Extra Long Drill for Metal designed for deep drilling in Drilling Machines and workshop applications. Extra Long design for deep drilling Fully Ground shank for high runout accuracy HSS-G Material for hard metal performance 135° Point Angle optimized for tough alloys Bright Finished surface for consistent chip evacuation Deep reach and faster metal removal for demanding tasks Engineered as an Extra-Long solution, this Twist Drill delivers extended reach with a Gesamtlänge of 295 mm and a Spiral Length of 200 mm, making it ideal for deep-hole tasks. The HSS-G construction and the special flute geometry enable up to 40 % faster drilling and require 50 % less Anpresskraft compared with conventional HSS tools, which translates to higher productivity on long runs and reduced operator fatigue. Precision geometry that creates clean, accurate holes Thanks to the Fully Ground flute geometry and precise Points, the drill achieves very sharp cutting edges and excellent Rundlaufgenauigkeit. The 135° Point Angle is tailored for harder Werkstoffe and shortens Anbohrzeit, while the DIN 1869 specification ensures consistent quality. Because ground tools can be more brittle, stationary operation with coolant is recommended to preserve tool life and hole quality. Suited materials and professional workshop applications This Twist Drill is intended for a wide range of Metall applications, including legierten and unlegierten Stahl, Gussstahl, Gusseisen, Sintereisen, Temperguss, Nichteisenmetalle and Hartkunststoff, and is rated for materials up to 1000 N/mm². Workshops, toolrooms and industrial users benefit from the combination of depth capability and cutting performance when working on components that require deep, precise bores. Handling, sharpening and practical tips for longer service life For best results mount the drill concentrically in a suitable Chuck of a Drilling Machine and use sufficient coolant during operation. The Ausspitzung (point preparation) reduces Querschneide and lowers Reibkräfte, so lower Vorschubkräfte are sufficient and centering improves. If regrinding is necessary, maintain the 135° geometry to preserve performance; note that ground HSS-G drills are easier to resharpen yet require careful handling to avoid breakage. If unsure whether this tool fits specific requirements, METAV Werkzeuge offers comprehensive technical advice to help select the right solution. Strong recommendation: Choose the MetavCUT Twist Drill for deep, demanding metal drilling and consult METAV Werkzeuge for expert support — Email: info@metav-werkzeuge.com · Phone: +49 2822 7131930 · WhatsApp: +49 170 2837271 Technical Information Designation: Twist Drill Brand: MetavCUT SKU: 34045-FDA Diameter: 4.5 mm Overall Length: 295 mm Spiral Length: 200 mm Point Angle: 135° Execution: extra long Colour: bright finished Shank Execution: fully ground Material: HSS-G Norm: DIN 1869 For: Drilling Machine Model Series: Standard Line Application: Drills for metal Packaging Unit: 10 Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily applied to the machining of high-strength Werkstoffe and large bore diameters; its form allows relatively easy resharpening and it withstands considerable Belastungen, making it suitable for demanding metalworking tasks. Which three drill types exist? There are three common drill categories: Metal Drills, Wood Drills and Stone/Concrete Drills; the MetavCUT Twist Drill belongs to the Metal Drills group and is optimized for metalwork. Why are Twist Drills pointed? The point geometry reduces the Querschneide at the Tip of the Twist Drill; by pointing, frictional forces are significantly lowered and smaller Vorschubkräfte are needed while the Tip centers better in the Workpiece. Can you use metal drills in wood? A Metal Drill such as the MetavCUT Twist Drill can be used in Wood, but guidance is poorer and the bore finish may be less clean; however, Metal Drills are easier to resharpen and show less self-feed tendency. For which bore depths is the Twist Drill most commonly used? A through-hole is commonly executed with a Twist Drill; for diameters up to 20 mm and drill depths up to 100 mm, the Twist Drill is the most frequently used tool, while the extra-long MetavCUT version extends that capability for deeper bores. Is HSS or HSSE better? The general belief that HSSE steels are inherently superior to HSS is not universally correct; evaluate working conditions carefully to decide whether the higher investment in HSSE is justified for your specific MetavCUT application.
4.5mm HSS-G Twist Drill DIN 1897 ,extra short, bright finished, Type N - MetavCUT
Twist Drill — Type N, 4.5 mm, 135°, Extra Short, Bright Finished, HSS‑G, DIN 1897 (Cylindrical Shank) by MetavCUT The Twist Drill Type N is an extra short HSS‑G drill designed for Drilling Machines and Hand Drills, offering high stability and efficient metalworking in tight or thin‑walled components. Extra‑short design for improved stability Optimised 135° tip for harder materials HSS‑G construction for long tool life Cylindrical shank fits standard chucks Standard Line quality for professional use Compact design increases stability and reduces breakage The Twist Drill in an extra short execution combines a reduced Overall Length with a shortened Spiral Length to deliver superior Verdrehungsfestigkeit (torsional stability) compared with standard drills. Shorter geometry reduces the lever arm and thus the risk of bending and breakage, which is especially valuable when working in constrained assemblies or on thin sheet and profile parts. The result is more reliable hole quality and fewer tool changes during demanding metalworking tasks. 135° point angle and Type N spiral for tougher materials A 135° tip halves the tendency to wander on tough surfaces and shortens the initial penetration phase, which is advantageous when machining stainless steel and other hard alloys. The Type N normal spiral profile is optimised for Metal work and provides consistent chip evacuation and cutting behaviour across legierte und unlegierte Stähle, Gusswerkstoffe and non‑ferrous metals. For operators this means cleaner entry holes and predictable feed forces when using a Hand Drill or Drilling Machine. Practical handling: cylindrical shank and compatibility Equipped with a Cylindrical Shank, this Twist Drill clamps securely in standard three‑jaw chucks and is universally compatible with conventional drill chucks. While cylindrical shanks are broadly adaptable, users should ensure correct chuck tightening to avoid slippage under high torque; using a torque‑controlled drill or a drill sleeve can further improve safety. The bright finished surface assists in visual inspection of wear and facilitates cleaning after use. Target users and best applications Developed for machinists, fitters and maintenance technicians, the MetavCUT Standard Line Twist Drill is particularly well suited to workshop tasks that require robust Metal drilling in tight spaces and accurate hole positioning. Conforming to DIN 1897 and made from HSS‑G, this tool balances cost and performance for professional everyday use and for jobs where straightforward regrindability and dependable cutting speed are required. For precision metalworking choose MetavCUT’s Twist Drill Type N with Extra Short design — METAV Werkzeuge offers comprehensive technical advice and personalised support: eMail info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Technical data Designation: Twist Drill Brand / Manufacturer: MetavCUT SKU: 56045-FDA Diameter: 4.5 mm Point Angle: 135° Execution: Extra short Finish / Colour: Bright finished Material: HSS‑G Type: Type N Spiral Length: 24 mm Total Length: 58 mm Shank Execution: Cylindrical For Drilling Machine: Drilling Machine (Hand Drill) Model Series: Standard Line Application: Drills for Metal Standard: DIN 1897 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Is the Twist Drill Type N from MetavCUT suitable for hand drills? Yes. The MetavCUT Twist Drill Type N with a Cylindrical Shank is designed for use in Hand Drills and standard chucks; its Extra Short geometry improves stability in manual operations and reduces the risk of breakage when clamping and feeding correctly. What is the Twist Drill used for? The Twist Drill Type N by MetavCUT is primarily applied to the machining of high‑strength materials and larger hole diameters; its form is straightforward to regrind and withstands higher loads, making it ideal for steels, cast materials and hard plastics. Which three drill types exist? Common categories are Metal drills (such as the MetavCUT Twist Drill Type N), Wood drills, and Stone/Concrete drills. Why are Twist Drills pointed? Twist Drills are pointed to reduce the cross‑cut at the tip; this lowering of the cross‑edge decreases friction so that significantly lower feed forces are required and the drill centers more reliably in the workpiece. Can a metal drill be used in wood? A Metal drill such as the MetavCUT Twist Drill can be used in Wood, but guidance and finish may be inferior compared with dedicated Wood drills; however, metal drills are easier to regrind and tend to produce less self‑feeding. For which drilling depths is the Twist Drill most commonly used? A through‑hole in solid material is typically executed with a Twist Drill; for diameters up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most commonly used tool. Is HSS or HSSE better? There is no universal answer; the belief that HSSE steels are always superior to HSS is incorrect. Assess whether your working conditions justify the higher cost of HSSE before choosing.
4.5mm HSS-G Twist Drill DIN 338 ,fully ground, silver - MetavCUT
Nutzen Sie die Kombination aus HSS-G Schneidleistung und Sechskant Schaft für schnelle, präzise Metallbohrungen; der geschliffene Spiralbohrer reduziert die Anpresskraft und beschleunigt den Bohrvorgang spürbar. Bestellen Sie den Spiralbohrer von MetavCUT über Metav oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer HSS-G von MetavCUT Der Spiralbohrer HSS-G ist für präzise Metallbohrungen ausgelegt und eignet sich für Handbohrmaschine und stationäre Anwendungen Geschliffener HSS-G für hohe Schneidleistung Sechskant Schaft für formschlüssigen Werkzeugwechsel DIN 338 Kurzspiralbohrer für Metallbearbeitung Spirallänge 46 mm für effiziente Spanabfuhr Präzision und Leistung bei Metallbohrungen erreichen mehr Effizienz Der geschliffene HSS-G Spiralbohrer liefert scharfe Schneidkanten und hohe Rundlaufgenauigkeit, was zu saubereren Bohrlöchern führt. Durch die spezifische Ausführung lässt sich die Vorschubkraft deutlich reduzieren, was in der Praxis ein bis zu 40 % schnelleres Bohren und 50 % weniger Anpresskraft ermöglicht. Diese Kombination reduziert die Maschinenlaufzeit und steigert die Produktivität in Werkstatt und Produktion, ohne zusätzliche komplexe Werkzeuge zu benötigen. Vielseitige Einsatzgebiete für Werkstatt, Montage und DIY Mit einem Durchmesser von 4,5 mm fällt dieser Spiralbohrer in den Standard-Bereich und ist ideal für allgemeine Werkstattarbeiten, Montageaufgaben und DIY-Projekte. Er eignet sich für dünne bis mittlere Bleche, Profile, Flachstahl, Aluminium und Kunststoffe. Für hochpräzise Passungen empfiehlt sich das Voranstechen mit einem Zentrierbohrer, um Wandern auf der Oberfläche zu vermeiden und exakte Passmaße zu erreichen. Praktische Handhabung und Tipps für lange Lebensdauer Der Sechskant Schaft ermöglicht schnellen Wechsel in Bit-Haltern und reduziert Körnerschlupf bei Akkuschraubern. Weil geschliffene Bohrer empfindlicher gegenüber Stoßbelastung sind, empfiehlt sich bei intensiver Nutzung die stationäre Aufnahme und der Einsatz von Kühlmittel, besonders bei legierten Stählen. Für Durchmesser im Standard-Bereich kann meist direkt gebohrt werden; bei sehr hoher Präzision hilft ein Anpunktieren, die Zentrierung zu gewährleisten. Normgerechte Qualität und materialtechnische Vorteile Die Einhaltung der DIN 338 garantiert die Zuordnung als kurzer Spiralbohrer mit Zylinderschaft und macht die Standard Line von MetavCUT planbar in Bestückung und Einsatz. HSS-G steht für geschliffenen Schnellarbeitsstahl, der durch seine Schärfe saubere Bohrbilder erzeugt und besonders für legierte sowie unlegierte Stähle geeignet ist. Die kompakte Bauweise mit einer Spirallänge von 46 mm sorgt für zuverlässige Spanabfuhr und reduziert Verstopfungen bei Metallbearbeitung. Empfehlung: Für präzise und wirtschaftliche Metallbearbeitung wählen Sie den MetavCUT HSS-G Spiralbohrer aus der Standard Line — bei Fragen erreichen Sie uns per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Artikelnummer: 57045-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Norm: DIN 338 Daten Durchmesser: 4,5 mm Gesamtlänge: 98 mm Spirallänge: 46 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Material: HSS-G (geschliffener Schnellarbeitsstahl, hohe Schärfe) Ausführung: geschliffen Schaft: Sechskant (E6.3 kompatibel) Farbe: Silber Für Bohrmaschine: Handbohrmaschine FAQ Ist der Spiralbohrer für legierte Stähle geeignet? Der MetavCUT Spiralbohrer HSS-G ist speziell für legierte und unlegierte Stähle sowie Gusswerkstoffe ausgelegt und bietet durch den geschliffenen Schliff saubere Bohrbilder und gute Schneidleistung. Kann der Sechskant Schaft im Akkuschrauber verwendet werden? Ja, der Sechskant Schaft ist für den Einsatz in Bit-Haltern von Akkuschraubern geeignet und sorgt für formschlüssige Drehmomentübertragung ohne Durchrutschen. Welche Vorteile bietet die DIN 338 Norm bei diesem Bohrer? Die DIN 338 Klassifikation steht für kurze Spiralbohrer mit Zylinderschaft und gewährleistet kompatible Abmessungen sowie reproduzierbare Fertigungsqualität in der Standard Line von MetavCUT. Brauche ich Vorbohren mit dem 4,5 mm Bohrer? Für Standardanwendungen im Bereich 2,0–13,0 mm kann in der Regel direkt gebohrt werden; bei hochpräzisen Passungen empfiehlt sich vorheriges Zentrieren oder Anpunktieren. Welche Pflege verlängert die Lebensdauer des Bohrers? Kühlmittel bei Stahlbearbeitung, moderate Vorschubgeschwindigkeit und stationäre Aufnahme bei intensiver Nutzung vermeiden Überhitzung und Bruchrisiko des geschliffenen HSS-G Werkzeugs.
4.5mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N short, Ø 4.5 mm, 135°, HSS‑G, bright finished, DIN 338 A short Twist Drill (Type N) designed for precise metalworking with drilling machines and hand drills. Short design increases rigidity and precision Ground HSS-G for sharp cutting and clean holes 135° tip for hard materials like stainless steel Suitable for drilling machines and handheld drills Conforms to DIN 338 for short cylindrical shank drills Precision and stability for demanding metalwork The short execution of this Twist Drill reduces overhang and therefore bending, delivering noticeably higher stability during machining. With a diameter of 4.5 mm and an overall length of 80 mm, the compact geometry is ideal for tight setups and precise centre‑to‑centre tolerance work. The Type N spiral is the classic geometry for metal drilling, while the DIN 338 designation guarantees standardised dimensions and performance expectations for short cylindrical‑shank drills. Faster cutting with lower feed force A ground HSS‑G flute geometry enables up to 40% faster drilling and requires about 50% less feed force compared with conventional HSS variants under comparable conditions. This means shorter cycle times and reduced operator exertion when producing series holes in alloyed and unalloyed steels, cast steels, sintered irons and certain hard plastics. The 135° tip reduces initial point pressure and improves centring when entering harder materials, shortening dwell time on the workpiece surface. Applications and machine compatibility This Twist Drill is developed for drilling metal: steel, cast iron, non‑ferrous metals and hard plastics. It is suitable for both stationary drilling machines and portable hand drills where increased rigidity and accurate hole quality are required. The fully ground shank aids consistent clamping in chucks and collets, and the bright finished surface supports chip evacuation and inspection. Use coolant for deep or continuous cuts to preserve tip life and hole quality. Handling, life cycle and practical tips Because the flutes and geometry are produced by CNC grinding, the drill offers high runout accuracy and very sharp cutting edges, giving clean bores and reduced burr formation. Note that ground HSS drills can be more brittle than rolled variants; avoid excessive shock and use machine‑steady feeds. Re‑sharpening is possible but should be performed by experienced toolmakers to retain geometry. For optimal results, pair the drill with appropriate cutting speeds and lubricants for the specific metal being machined. For precision metal drilling tasks, choose the MetavCUT Twist Drill Type N short — METAV Werkzeuge provides expert advice and technical support: info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 45045-FDA Diameter: 4.5 mm Tip angle: 135° Type: Type N Execution: short Colour / Finish: bright finished Shank execution: fully ground Material: HSS-G Standard: DIN 338 Overall length: 80 mm Spiral length: 47 mm Application: Drills for metal For drilling machine: Drilling Machine Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials is the MetavCUT Twist Drill Type N best suited for? The MetavCUT Twist Drill Type N is primarily intended for metalworking and performs well in alloyed and unalloyed steel, cast steel, cast iron, sintered iron, non‑ferrous metals and hard plastics, offering reliable hole quality when used with correct speeds and cooling. Can the MetavCUT Twist Drill be used in a hand drill? Yes, the MetavCUT Twist Drill is suitable for both stationary drilling machines and hand drills (Drilling Machine), but the short design particularly benefits setups that demand rigidity and precision; always ensure secure clamping and compatible cutting parameters. What are twist drills used for? Twist Drills are mainly applied when machining high‑strength materials and larger hole diameters; their form is easy to regrind and resists higher loads, making them suitable for demanding metalworking operations. Which 3 drill types exist? The three primary drill categories are metal drills, wood drills and stone/concrete drills.
4.5mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Wirtschaftlichkeit, Haltbarkeit und Präzision verbinden sich in diesem Spiralbohrer zu einem effizienten Werkzeug für Metallarbeiten. Die TiN-beschichtete Oberfläche reduziert Reibung und verlängert die Lebensdauer, während die geschliffene HSS-G-Geometrie und die kurze Ausführung für stabile, präzise Bohrungen sorgen. Bestellen Sie den Bohrer direkt über Metav oder fragen Sie unsere Beratung an. Spiralbohrer 4,5 mm von MetavCUT – kurzer HSS-G Bohrer (Typ N) Der Spiralbohrer 4,5 mm ist ein kurzer, geschliffener HSS-G Bohrer, ausgelegt für präzise Bohrungen in legierten und unlegierten Stahl sowie in Guss- und Nichteisenmetallen. Spiralbohrer »Spiralbohrer« von MetavCUT TiN-Beschichtung reduziert Reibung und Verschleiß Geschliffen: hohe Rundlaufgenauigkeit Kurze Ausführung für stabile Präzisionsbohrungen Spitzenwinkel 135° für harte Werkstoffe Hohe Standzeit durch Beschichtung und Materialwahl Die Kombination aus HSS-G und TiN-beschichteter Oberfläche sorgt für eine spürbar längere Standzeit bei Metallbearbeitung. Durch die Titan-Nitrid-Beschichtung verringert sich die Reibung an der Schneide, was Wärmeentwicklung und Werkzeugverschleiß reduziert. Für Anwender bedeutet das weniger Werkzeugwechsel, höhere Ausbringung und geringere Stillstandzeiten bei Serien- und Einzelfertigung. Kurz ausgeführte Bauform für präzise Ergebnisse Die kurze Ausführung reduziert die Auskraglänge und verbessert dadurch die Stabilität während des Bohrens. Diese Konstruktion minimiert das Verbiegen und Wandern des Werkzeugs, wodurch saubere Bohrbilder und engere Toleranzen erzielt werden. Besonders bei stationären wie auch handgeführten Maschinen ist die kürzere Bauform vorteilhaft, weil sie kontrollierten Vorschub und bessere Rundlaufgenauigkeit ermöglicht. Geschliffene Geometrie und Schneidvorteile Durch den CNC-basierten Schliff der Spannuten erreicht der Bohrer eine scharfe Kantengeometrie und hohen Rundlauf. Die geschliffene Ausführung unterstützt ein bis zu 40 % schnelleres Bohren bei gleichzeitig 50 % geringerer Anpresskraft im Vergleich zu konventionellen HSS-Bohrern. Anwender profitieren von schnellerem Arbeitsfortschritt und ergonomischerer Handhabung, vor allem bei der Bearbeitung harter Werkstoffe. Eignung und Anwendungsempfehlung für Werkstatt und Montage Mit einem Durchmesser von 4,5 mm fällt das Produkt in den Standard-Bereich für Alltagsanwendungen und eignet sich für Werkstatt, Montage und anspruchsvolle DIY-Projekte. Der Typ N Normalspirale ist für Metall bohrungen konzipiert und eignet sich besonders für legierte und unlegierte Stähle, Temperguss, Gusseisen sowie Nichteisenmetalle. Bei stationären Einsätzen empfiehlt sich eine Kühlmittelzufuhr, um die Lebensdauer weiter zu erhöhen. Für präzise Metallbohrungen empfiehlt MetavCUT die Verwendung dieses kurz ausgeführten, TiN-beschichteten HSS-G Bohrers; bestellen Sie unkompliziert über Metav und kontaktieren Sie uns bei Detailfragen per eMail info@metav-werkzeuge.com Produktmerkmale Artikelnummer: 46045-FDA Marke: MetavCUT Serie: Standard Line Daten Durchmesser: 4,5 mm Gesamtlänge: 80 mm Spirallänge: 47 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G Norm: DIN 338 Farbe: TIN-beschichtet Schaft Ausführung: geschliffen Typ: Typ N Ausführung: kurz Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 SKU: 46045-FDA FAQ Für welche Materialien eignet sich der Bohrer primär? Der MetavCUT Spiralbohrer in 4,5 mm eignet sich primär für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie für Nichteisenmetalle und Hartkunststoff. Die Kombination aus HSS-G und TiN-beschichtung macht ihn besonders geeignet für anspruchsvolle Metallarbeiten. Ist die kurze Ausführung auch für Handbohrmaschinen geeignet? Ja, die kurze Ausführung ist für Handbohrmaschinen geeignet und bietet durch die reduzierte Auskraglänge bessere Stabilität. Bei handgeführten Anwendungen empfiehlt sich dennoch kontrollierter Vorschub und gegebenenfalls Anpunktieren für höchste Präzision. Welche Vorteile bringt die geschliffene Schaftausführung? Die geschliffene Ausführung sorgt für scharfe Kanten und hohe Rundlaufgenauigkeit, was sauberere Bohrlöcher und reproduzierbare Ergebnisse ermöglicht. Bei Verwendung des MetavCUT Spiralbohrers zeigt sich dies besonders in präzisen Metallbohrungen. Woraus ergibt sich die höhere Bohrgeschwindigkeit und verringerte Anpresskraft? Die Geometrie und der CNC-Schliff der Spannuten führen zu effizienterer Spanabfuhr und geringeren Reibungsverlusten. Dadurch kann der Bohrer bis zu 40 % schneller bohren und benötigt etwa 50 % weniger Anpresskraft gegenüber herkömmlichen HSS-Bohrern.
4.5mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — Long HSS‑G Twist Drill, 4.5 mm, 135° tip, Bright finished, Fully ground, DIN 340 The Twist Drill is a long‑version metal drilling bit designed for deep and hard‑material drilling with drilling machines and hand drills. Long design for deeper, hard‑to‑reach holes 135° tip for reliable entry into hard materials Fully ground HSS‑G for precise, clean holes DIN 340 standard for industrial compatibility Reach deep holes reliably with the long design The long execution of this Twist Drill (Total Length 126 mm, Spiral Length 82 mm) is ideal when holes must be drilled far from the workpiece edge or in recessed positions. The extended Spiral Length reduces the need for extensions or special fixtures, allowing deeper boreholes with consistent chip evacuation. This makes the bit particularly useful in maintenance, toolroom tasks, and assembly work where access is limited and reliability matters. Faster cutting and easier feed thanks to fully ground HSS‑G The HSS‑G material and fully ground flute geometry provide a sharper cutting edge and high concentricity. Compared with rolled HSS variants, a ground Twist Drill can cut up to 40% faster and requires significantly less feed force, which reduces operator fatigue and improves spindle load behaviour. The ground geometry also creates cleaner hole walls in alloyed and unalloyed steels, cast materials and non‑ferrous metals. Optimised tip geometry for harder materials A 135° tip angle reduces the tendency to wander on hard surfaces and shortens initial penetration time in tough materials such as stainless steels. The flatter tip distributes cutting forces better and is recommended when drilling high‑strength steels and cast materials up to the limits specified by the DIN 340 family. For best results, combine with appropriate coolant and moderate spindle speeds to balance tool life and surface finish. Practical guidance for use and durability The bright finished surface improves corrosion resistance and visual inspection, while the fully ground shank ensures a secure clamping fit in drill chucks. Although ground HSS bits can be more brittle than rolled types, correct coolant use and controlled feed rates extend service life considerably. For stationary machining and demanding metalworking applications, the Standard Line model offers a balanced compromise between performance and tool robustness. We recommend the MetavCUT Twist Drill for professionals who require deep, precise holes in metal — for personalised application advice or technical clarifications contact METAV Werkzeuge: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Technical Details Designation: Twist Drill Marke: MetavCUT SKU: 53045-FDA Diameter: 4.5 mm Total Length: 126 mm Spiral Length: 82 mm Tip Angle: 135° Material: HSS‑G Execution: long Shank execution: fully ground Colour / Finish: bright finished For Drilling Machine: Drilling Machine / Hand Drill Application: Drills for metal Model Series: Standard Line Norm: DIN 340 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can this Twist Drill be used in a hand drill or only in a machine? The MetavCUT Twist Drill is suitable for both drilling machines and hand drills, but for best precision and tool life use in a stable chuck with controlled speeds; heavier use in stationary machines with coolant is recommended for harder materials. What is a Twist Drill used for? A Twist Drill is primarily applied to the machining of high‑strength materials and larger bore diameters; it is relatively easy to regrind and withstands high cutting loads, making it suitable for alloyed and unalloyed steels, cast materials and other demanding applications. Which three drill types are there? The main drill categories are metal drills (such as HSS Twist Drills), wood drills, and stone/concrete drills.
4.6mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Robuste HSS-Konstruktion und kurze Ausführung bieten hohe Stabilität und präzise Bohrung in Stahl; die DIN 338-Konformität gewährleistet Kompatibilität mit stationären Bohrmaschinen. Bestellen Sie den Spiralbohrer direkt über Metav oder kontaktieren Sie unsere Beratung für technische Details und Einsatzempfehlungen. Spiralbohrer von MetavCUT – kurzer HSS Twist Drill für Metallbearbeitung Der Spiralbohrer von MetavCUT ist ein kurzer HSS-Spiralbohrer, der für präzise Metallbohrungen an stationären und handgeführten Maschinen konzipiert wurde HSS-Material für legierten und unlegierten Stahl DIN 338: kurze Spiralbohrer für stationäre Maschinen Typ N-Normalspirale optimal für Metallbohrungen Ø 4,6 mm mit hoher Stabilität bei kurzer Ausführung Geeignet für Handbohrmaschine und stationäre Maschinen Stabilität durch kurze Ausführung und HSS-Material für saubere Bohrungen Die Kombination aus HSS-Werkstoff und kurzer Konstruktion reduziert die Auslenkung während des Bohrens und minimiert das Bruchrisiko bei kleinen Durchmessern. Durch die kurze Ausführung verringert sich die Auskraglänge, was eine höhere Rundlaufstabilität und damit sauberere Bohrbilder in Stahl und Gusseisen ermöglicht. Anwender profitieren von geringerer Nacharbeit und konstanter Maßhaltigkeit. Präzision beim Anbohren und Empfehlungen für Spitzenwinkel Für viele Metallarten bietet der Spitzenwinkel 118° ein ausgewogenes Anbohrverhalten; dieser Winkel erleichtert das Zentrieren auf gewölbten Oberflächen und eignet sich besonders für legierte und unlegierte Stähle. Für härtere Werkstoffe kann ein anderer Spitzenwinkel sinnvoll sein; bei Standardanwendungen in Werkstatt und Montage ist die Einstellung 118° jedoch oft die wirtschaftlichste Wahl. Einsatzgebiete, Maschinentypen und Durchmesser-Cluster Mit Ø 4,6 mm liegt der Bohrer im Standard-Bereich, ideal für Werkstatt, Montage und DIY-Projekte. Die Ausführung eignet sich für dünne bis mittlere Bleche, Profile und Flachstähle sowie für Handbohrmaschine und stationäre Säulenbohrmaschinen. Bei Anforderungen an hohe Serienraten oder extrem gehärtete Werkstoffe sollte auf Vollhartmetall oder spezialisierte Werkzeuge ausgewichen werden. Handhabung, Vorschub und praktische Tipps für saubere Ergebnisse Vor dem Bohren empfiehlt sich leichtes Anpunkten zur Vermeidung von Wandern, besonders bei Handbohrmaschinen. Kühlung reduziert Wärmeeintrag und verlängert die Lebensdauer des Werkzeugs; Schneidöl ist bei Stahlbearbeitung empfohlen. Die Spirallänge 47 mm bietet genügend Spanraum für mittlere Bohrtiefen und unterstützt zuverlässige Spanabfuhr bei häufigen Werkstattaufgaben. Sichern Sie sich die präzise HSS-Qualität von MetavCUT und bestellen Sie über Metav oder kontaktieren Sie uns per eMail an info@metav-werkzeuge.com beziehungsweise telefonisch unter +49 2822 7131930 – wir beraten bei Einsatz und Maschinenauswahl. Produktmerkmale Artikelnummer: 40046-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Ausführung: kurz Typ: Typ N Material: HSS Norm: DIN 338 Farbe: schwarz Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 Fakten Durchmesser: 4,6 mm Gesamtlänge: 80 mm Spirallänge: 47 mm Spitzenwinkel: 118° Besonderheiten Typ: Typ N (Normalspirale, Metall) Material: HSS (Schnellarbeitsstahl) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Ausführung: kurz (hohe Stabilität, geringe Auskragung) Farbe: schwarz FAQ Für welche Materialien eignet sich der Bohrer am besten? Der MetavCUT Spiralbohrer in HSS eignet sich vor allem für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; bei sehr harten Stählen kann ein anderes Werkzeug wirtschaftlicher sein. Ist der Bohrer für Handbohrmaschinen geeignet? Ja, die kurze Ausführung und der Durchmesser von 4,6 mm machen den Spiralbohrer von MetavCUT kompatibel mit Handbohrmaschine und bieten ausreichend Stabilität für typische Werkstattanwendungen. Welcher Spitzenwinkel ist verbaut und warum? Der Spiralbohrer verfügt über einen Spitzenwinkel von 118°, der eine gute Balance aus Zentrierverhalten und Vorschub erzielt und sich gut für viele Stahlarten eignet. Wie tief kann mit diesem Bohrer sicher gebohrt werden? Die Spirallänge von 47 mm und die Gesamtlänge von 80 mm erlauben mittlere Bohrtiefen; für sehr tiefe Sacklochbohrungen sind abgestufte Vorgehensweisen oder spezielle Werkzeuge empfehlenswert. Welche Norm gilt für diesen Bohrer und welche Vorteile bringt sie? Die Einhaltung der DIN 338 garantiert die standardisierte Bauform kurzer Spiralbohrer mit Zylinderschaft und erleichtert die Auswahl für stationäre Maschinen sowie die Vergleichbarkeit technischer Daten.
4.6mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Dieser kurze Abriss fasst die Stärken zusammen: HSS-E für erhöhte Standzeit, die kurze Ausführung für maximale Stabilität und der 135° Spitzenwinkel für sicheres Anbohren in harten Werkstoffen sorgen für präzise Ergebnisse. Bestellen Sie das Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung bei Bedarf an. MetavCUT Spiralbohrer 4,6 mm — Standard Line (kurze Ausführung) MetavCUT Spiralbohrer 4,6 mm in kurzer Ausführung für präzise Metallbearbeitung mit Handbohrmaschine Kurze Ausführung für hohe Stabilität HSS-E mit 5% Kobalt für längere Standzeit Geschliffen: Hohe Rundlaufgenauigkeit und scharfe Schneiden DIN 338 Klassifizierung für kurze Spiralbohrer 135° Spitzenwinkel ideal für harte Werkstoffe Präzision durch kompakte Bauweise für saubere Bohrbilder Die kurze Ausführung reduziert die Auskraglänge und minimiert Vibrationen, wodurch saubere Bohrbilder und hohe Maßhaltigkeit erreicht werden. Dieses Bohrwerkzeug ist speziell für stationäre und handgeführte Anwendungen konzipiert, bei denen Stabilität und kontrollierter Vorschub wichtiger sind als große Reichweite. Anwender profitieren von geringerem Wanderverhalten beim Anbohren und einer zuverlässigeren Zentrierung auf der Oberfläche. Langlebigkeit und Einsatz in anspruchsvollen Materialien Der Einsatz von HSS-E mit 5% Kobalt erhöht die Warmfestigkeit und Widerstandsfähigkeit gegen Verschleiß, deshalb eignet sich der Kurzbohrer besonders für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle. Der 135° Spitzenwinkel verringert die Anbohrkraft bei harten Werkstoffen und verlängert die Werkzeuglebensdauer. Durch fachgerechte Kühlung und stationären Einsatz lässt sich die Performance weiter optimieren. Geschliffene Geometrie für höchste Genauigkeit Die geschliffene Schaft- und Spannutengeometrie garantiert scharfe Schneiden und hervorragende Rundlaufgenauigkeit. Das Resultat sind präzise, gratarme Bohrungen mit definierten Toleranzen. Für Anwendungen, die saubere Passungen verlangen oder nachbearbeitungsarme Ergebnisse benötigen, bietet diese Ausführung klare Vorteile gegenüber gewalzten Varianten. Geeignete Einsatzbereiche und Anwenderhinweise Im Standard-Bereich (2,0–13,0 mm) ist dieses Werkzeug ideal für Werkstatt, Montage und überwiegende Metallbearbeitung. Bei Handbohrmaschinen empfiehlt sich ein ruhiger Vorschub und gegebenenfalls Vorzentrieren mit einem Zentrierbohrer, um das Wandern zu minimieren. Für tiefe oder großserielle Bohrungen sind spezialisierte Aufbohrverfahren oder andere Werkzeugtypen wirtschaftlicher. Empfehlen Sie das MetavCUT Kurzbohrersystem mit HSS-E für präzise Metallbohrungen; bei Fragen stehen unsere Techniker zur Verfügung – per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Leistungsmerkmale Artikelnummer: 47046-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Typ: Typ N Norm: DIN 338 Zahlen Durchmesser: 4,6 mm Gesamtlänge: 80 mm Spirallänge: 47 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS-E (Schnellarbeitsstahl, 5% Kobalt erhöht Warmfestigkeit) Schaftausführung: geschliffen (CNC-Schliff für hohe Rundlaufgenauigkeit) Ausführung: kurz (reduzierte Auskraglänge, höhere Stabilität) Für Bohrmaschine: Handbohrmaschine Anwendung: Bohrer für Metall (legierter und unlegierter Stahl, Gusseisen, Nichteisenmetalle, Kunststoffe) Normhinweis: DIN 338 beschreibt kurze Spiralbohrer mit Zylinderschaft FAQ Kann der Spiralbohrer für Edelstahl verwendet werden? Der MetavCUT Spiralbohrer aus HSS-E mit 135° Spitzenwinkel ist für harte Werkstoffe geeignet und kann für viele Edelstahlarten verwendet werden, allerdings empfiehlt sich konstante Kühlung und angepasste Schnittgeschwindigkeit; bei sehr zähen Edelstählen sind speziell legierte Sorten zu prüfen. Welche Bohrmaschine ist passend für dieses Werkzeug? Für stationäre Säulenbohrmaschinen und Handbohrmaschinen ist der MetavCUT Spiralbohrer 4,6 mm (SKU 47046-FDA) geeignet; bei Handgebrauch auf stabile Führung und Vorzentrierung achten, um Bruchrisiken zu minimieren. Worin liegt der Unterschied zwischen geschliffenen und gewalzten Bohrern? Geschliffene Bohrer, wie dieser Kurzbohrer, bieten schärfere Schneiden und bessere Rundlaufgenauigkeit, was zu präziseren Bohrlöchern führt; gewalzte Varianten sind tendenziell zäher, aber weniger scharf. Für welche Materialien ist dieser Kurzbohrer besonders empfohlen? Der MetavCUT Spiralbohrer eignet sich besonders für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe, dank HSS-E und der kurzen Bauform für stabile Bearbeitung. Wie verhält sich der Bohrer bei tiefen Bohrungen? Bei Bohrungen über das Fünffache des Durchmessers hinaus empfiehlt sich mehrstufiges Vorgehen oder spezielle Spiralgeometrien; für das hier angebotene Kurzformat sind eher flachere Durchdringungen und präzise, kontrollierte Einsätze vorgesehen.
Reliable performance for daily drilling
The Standard line is a versatile series of HSS (high-speed steel) twist drills, also described as standard twist drills or precision HSS twist drills, engineered for everyday industrial and workshop use. Positioned between economy options and specialist pro-grade tools, the standard line delivers consistent, repeatable results for regular drilling tasks without the need for high-cost alloys.
How the standard line performs in practice
Designed as precision ground (HSS‑G) twist drills, the standard line combines a refined manufacture process with a classic geometry. A typical 118° tip and a cleanly formed point give good penetration and reliable centring, while extremely smooth flute surfaces support efficient chip evacuation. The result is stable running, improved hole quality and extended tool life under normal production and maintenance conditions.
Key advantages that matter on the shop floor
- Reduced rework thanks to high concentricity and precise hole quality
- Lower tool consumption through enhanced wear resistance from precision grinding
- Faster cycle times via efficient chip removal from smooth flutes
- Broad applicability across common materials: steel, cast iron, sintered metal, plastics and non‑ferrous metals
- Ideal balance of performance and cost for workshops, maintenance teams and assembly lines
Technical data
- Material: HSS (high-speed steel)
- Manufacture: precision ground (HSS-G)
- Tip angle: 118° (typical)
- Features: smooth flutes, optimised point geometry, excellent concentricity
- Applications: unalloyed steel, low-alloy steel, cast iron, sintered metal, plastics, non‑ferrous metals
Why Metav is the smart sourcing choice
Metav stands for democratisation of precision. As an experienced precision partner, Metav combines decades of technical know-how with a broad assortment, making high-quality measuring and workshop tools accessible to small and large operations alike. With over 48,000 customers, more than 250,000 products and a logistics hub in Emmerich, Metav offers dependable supply and a curated quality filter for the european market — the sensible route to equip your shop with standard line twist drills and complementary tooling.
FAQ
What materials are standard line twist drills suitable for?
The standard line twist drills are suitable for unalloyed and low‑alloy steel, cast iron, sintered metal, plastics and non‑ferrous metals, matching typical workshop and light industrial requirements.
How does the precision ground (HSS‑G) design benefit drilling results?
Precision ground manufacture increases concentricity and improves cutting edge finish, which leads to better hole quality, reduced vibration and longer tool life compared with roll‑formed entry‑level drills.
Are standard line drills a substitute for pro‑grade specialist drills?
Standard line drills are intended as the reliable everyday option; they deliver consistent performance for regular production and maintenance but are not a replacement when extreme loads or specialised alloys demand pro‑grade materials.
Which synonyms should procurement teams use when searching for these tools?
Search terms such as “standard twist drills”, “HSS standard drills” or “precision HSS twist drills” will reliably lead to the standard line and comparable products.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com