Precision micrometers for reliable dimensional control
Micrometers deliver precise length and depth measurements in metalworking, enabling repeatable control over component tolerances and process stability. These instruments—available as outside micrometers, inside micrometers and depth micrometers—offer hardened contact faces and fine-thread spindles to ensure long-term accuracy and resistance to wear, with digital versions providing data transfer via USB or Bluetooth for seamless integration into inspection software. Typical uses include measuring small bores, depths and diameters in precision engineering, where features must be defined to micrometre-level accuracy; features such as ratchet thimbles and insulated frames help maintain consistent measuring force and temperature compensation. Choose between robust analog models, IP54-protected digital micrometers or micrometers with an integrated minicomputer for advanced functions like unit conversion, temperature correction and Go/NoGo evaluations.
350mm Micrometer With Colour Touchscreen, Wireless & USB Output, ISO 17025 Calibrated - Microtech Metrology
Take advantage of traceable, workshop-ready precision with a large-range digital micrometre that pairs a 2.4" colour touchscreen and wireless/USB data output with an ISO 17025 calibration certificate for immediate use; the stated accuracy of 0.009 mm and a reading resolution of 0.0001 mm ensure reliable quality control. Order the micrometre directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology Micrometre Metric 60 — 325–350 mm, ISO 17025 calibrated, Wireless + USB The Microtech Metric 60 micrometre is a heavy‑duty digital micrometre designed for precise measurement of medium to large components in inspection and production environments, combining a large measuring range with modern data connectivity. Large 325–350 mm measuring range ISO 17025 calibration certificate included 2.4" colour touchscreen display Wireless and USB data output Traceable accuracy for production-grade inspection A large-range digital micrometre with a stated accuracy of 0.009 mm provides quantifiable results for routine inspection and process control. The included ISO 17025 calibration certificate confirms traceability to recognised standards and reduces the administrative burden of incoming inspection: the instrument is delivered calibrated and ready for use in quality systems. The specified reading resolution of 0.0001 mm supports fine discrimination during setting and verification tasks, turning measured values into actionable data rather than estimations. For workshops that must document conformity, the combination of certified calibration and measurable accuracy directly supports auditability and consistent production decisions. Faster data capture and integration to streamline workflows Equipped with a 2.4" touchscreen and both Wireless and USB outputs, this digital micrometre accelerates measurement cycles and simplifies data transfer to inspection software or spreadsheets. The colour touch interface reduces menu navigation time and lowers the training threshold for operators, while the dual data ports enable either cable‑based logging or wireless transmission to a shop‑floor terminal. This connectivity reduces transcription errors, shortens inspection loops and supports traceable data collection — a practical productivity gain for routine quality checks and batch documentation. Designed for robust handling and practical workshop use The Metric 60 configuration covers the 325–350 mm band, making it suitable for medium‑sized components and machined assemblies where range and stiffness matter. A non‑rotating spindle preserves thread integrity on delicate surfaces and promotes repeatable contact geometry, while the supplied set of 6 anvils (0.4–7 mm) extends application flexibility for varied geometries. The instrument’s digital electronics are sealed for workshop environments, and the solid construction balances reach with operator handling to maintain measurement stability across typical inspection benches. These characteristics translate into fewer re‑measurements and more confidence in first‑pass acceptance. Choose the Microtech Metric 60 micrometre for certified, high‑accuracy measurement and contact Metav Werkzeuge in Emmerich for technical advice and reliable supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 110713258 GTIN: 4061905457081 ECLASS: 21170328 Manufacturer: Microtech Metrology Core specifications Measuring range: 325–350 mm Accuracy: 0.009 mm Resolution (reading): 0.0001 mm Display: Colour 2.4" touchscreen Features and accessories Data output: Wireless + USB Calibration: ISO 17025 certificate included Measuring spindle: non-rotating Accessories: 6x anvils 0.4–7 mm (Metric 60) Digital micrometre FAQ Is the micrometre delivered ready for official measurement tasks? The Microtech Metric 60 micrometre is supplied with an ISO 17025 calibration certificate, so it arrives calibrated and ready for traceable inspection work. How can measurement data be exported from the instrument? Data from the Microtech Metric 60 micrometre can be transmitted via Wireless or exported over USB for integration with quality systems and logging software. What component sizes is this micrometre suitable for? With a measuring range of 325–350 mm, the Metric 60 unit is intended for medium to large machined parts and assemblies where a long reach and stable measuring geometry are required. What level of precision does the instrument provide in everyday use? The instrument specifies an accuracy of 0.009 mm and a reading resolution of 0.0001 mm, supporting reliable acceptance decisions in production and inspection environments. Are spare anvils or special accessories included or available? The delivery includes 6 anvils (0.4–7 mm) for different contact situations; additional accessories compatible with the Metric 60 micrometre are available on request. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
350mm Setting Gauge Whitworth 55 Thread Standard - Microtech Metrology
Benefit from a purpose‑built Whitworth‑profile setting standard that combines clear specification and workshop compatibility: a Whitworth 55 profile with a 350 mm working length ensures reproducible setups and straightforward inventory integration. Order directly via Metav Werkzeuge or consult our advisors for technical matching. Setting gauge by Microtech Metrology — Whitworth 55, 350 mm Setting gauge for verifying and setting Whitworth 55 profiles and for use as a workshop reference in industrial metrology. Whitworth 55 profile for thread setting 350 mm working length for extended reach Precision metrology accessory, workshop grade Consistent setup and measurable benefits for production The instrument serves as a dedicated setting standard designed to bring repeatability to workshop and inspection routines. With its Whitworth 55 profile and a 350 mm working length, the device provides a stable reference that reduces setup variability and shortens adjustment cycles. In practical terms, this means fewer machine stops and a clearer basis for traceable comparisons — a direct contribution to throughput and quality control. The simplified geometry and explicit profile compatibility streamline integration into existing jigs and gauges, allowing a straightforward transfer of reference dimensions across fixtures. Integrates into established metrology workflows As an accessory for measurement systems, the gauge is intended to be used alongside height gauges, micrometres and comparators in routine checks and set‑ups. The clearly defined Whitworth 55 profile aids technicians in aligning tools and verifying thread forms without guesswork. Because the item is supplied by Microtech Metrology, the component matches professional metrology expectations and is suitable for recurring workshop tasks where consistent results are required. This accessory supports objective measurement practices and assists in documenting conformity during incoming inspection or pre‑machining set‑up. Practical advantages for the workshop and purchasing manager The compact, single‑purpose nature of the product reduces inventory complexity while offering a reliable reference for numerous operations. Procurement benefits from a straightforward specification — profile, length and manufacturer are explicit — which simplifies order processing and stocking. For plant managers, the gauge represents a focused tool that supports faster machine changeovers and clearer inspection records, helping to lower non‑productive time and contribute to continuous improvement efforts. Contact Metav Werkzeuge today for product matching and procurement advice; Metav’s specialists in Emmerich will assist with technical queries and order handling via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 110720035 GTIN: 4061905460098 Manufacturer: Microtech Metrology Working length: 350 mm Special feature: Whitworth 55 Facts Category: Metrology accessory Intended use: Workshop and inspection set‑up Origin: Manufacturer data supplied Special features Whitworth 55 thread/profile compatibility Accessory for measurement systems and fixtures Supplied as a measuring/setting standard FAQ What is the primary purpose of this setting gauge? The setting gauge from Microtech Metrology functions as a workshop reference for verifying and setting the Whitworth 55 profile and for aiding repeatable machine and fixture set‑ups. Can this gauge be used directly to check thread form? Yes, the gauge provides a defined Whitworth 55 profile suitable for comparative checks and for aligning tools and fixtures to that thread form. Which length is available and what does it mean for application? The working length is 350 mm, which offers extended reach for larger fixtures and provides a stable reference for longer set‑ups in the inspection area. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
350–375mm Micrometer With Colour 2.4" Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of high‑resolution measurement, modern data transfer and traceable calibration for reliable production checks; the micrometer offers 0.009 mm accuracy, Wireless + USB output and an ISO 17025 calibration certificate. Order the device directly via Metav Werkzeuge or consult our specialists for application advice. Micrometer Metrisch 60 by Microtech Metrology — Digital micrometer with 2.4‑inch colour touchscreen and Wireless + USB The Micrometer Metrisch 60 is a large‑range digital micrometer designed for precise workshop and laboratory measurements of medium to large components, offering a clear touch display and industrial data connectivity. ISO 17025 calibration certificate included Wireless and USB data output 2.4‑inch colour touchscreen display High resolution accuracy 0.009 mm Accurate, traceable measurements for quality control The instrument delivers traceable results thanks to the supplied ISO 17025 calibration certificate, which confirms laboratory calibration to an accredited standard. With an accuracy of 0.009 mm, the device is suited for demanding inspection tasks where small deviations matter; the specified tolerance supports process control and reduces the need for repeated rework. The measuring range of 350–375 mm covers medium‑sized components and fixtures, making the tool suitable for both workshop checks and incoming inspection. Modern data handling that speeds up inspection routines Equipped with Wireless and USB outputs and a 2.4‑inch colour touchscreen, the micrometer simplifies data collection and visual verification. Measurements can be transmitted directly to a PC or mobile receiver, reducing manual transcription errors and accelerating logging into quality management systems. The digital readout and intuitive touch interface cut down training time and let operators confirm measurements at a glance, improving throughput in repetitive measurement tasks. Robust mechanics and practical accessories for reliable daily use Mechanical design elements such as the non‑rotating spindle reduce surface marking and ensure repeatable contact geometry, while the inclusion of 6x anvils (0.4–7 mm) extends applicability to various thread and small‑feature inspections. The solid digital electronics are integrated with the mechanical frame so that precision is maintained under normal workshop conditions. This combination of durable mechanics and practical accessories supports consistent results across shifts and operators. Contact Metav Werkzeuge today for a tailored quotation and advice on integrating this Microtech Metrology micrometer into existing inspection workflows; delivery and calibration are managed from Emmerich for secure, reliable supply. Technical Data Article number: 110713508 GTIN: 4061905457203 Manufacturer: Microtech Metrology Type: Metrisch 60 Display: Colour 2.4‑inch touchscreen Data output: Wireless + USB Measuring range: 350–375 mm Accuracy: 0.009 mm Includes: 6x anvils 0.4–7 mm Calibration: ISO 17025 certificate included Core technical figures Measuring range min: 350 mm Measuring range max: 375 mm Display size: 2.4 inches Resolution / readout step: 0.0001 m (display resolution as supplied) Accuracy: 0.009 mm GTIN numeric identifier: 4061905457203 Features & Accessories Digital micrometer with colour touchscreen Wireless data transfer and USB interface Non‑rotating spindle for repeatable contact Supplied set of anvils for varied applications ISO 17025 accredited calibration certificate Suitable for workshop and laboratory inspection FAQ Is an official calibration certificate supplied with the micrometer? Yes. The micrometer is supplied fully calibrated with an ISO 17025 calibration certificate issued by an accredited laboratory. Can measurement data be transferred to a PC or data logger? Measurement data can be exported via Wireless or USB, enabling direct logging into inspection software or spreadsheets. What component sizes can be measured with this device? The measuring range covers components from 350 mm up to 375 mm, making it suitable for medium‑sized parts and assemblies. Are spare anvils or additional accessories available? The supplied set includes 6x anvils (0.4–7 mm); additional or replacement anvils for specific tasks are available on request and compatible with the micrometer’s anvil interface. Does the micrometer require special operator training? Basic instruction on the touchscreen operation and data transfer is generally sufficient; the clear 2.4‑inch colour touchscreen reduces the learning curve for standard inspection tasks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
350–375mm Precision Micrometer With 35mm Round Anvils Touchscreen Display Wireless USB ISO 17025 Calibrated - Microtech Metrology
The combination of high measuring range, traceable calibration and integrated data transfer makes this instrument a reliable choice for large-component dimensional control. Benefit from fast, error-reducing data capture via Wireless and USB and from the included ISO 17025 calibration certificate. Order the micrometer directly via Metav Werkzeuge or consult our specialists for application advice. Micrometer (digital outside micrometer) – 350–375 mm range, ISO 17025-calibrated by Microtech Metrology The micrometer for stable external measurements of large parts, fitted with disc anvils and a 1.54" touchscreen for clear readouts in workshop and production environments ISO 17025 calibration certificate included Measuring range 350–375 mm Touchscreen 1.54" display Wireless and USB data output Traceable precision for large-format measurements This digital outside micrometer delivers reproducible external measurements across a substantial span. The instrument is specified for a measuring range of 350–375 mm and achieves an accuracy of ±0.009 mm, ensuring suitability for dimensional control tasks in fixture and component manufacture. The large Ø35 mm anvils increase contact area and reduce point loading on uneven surfaces, while the non-rotating spindle limits surface damage and improves repeatability. The included ISO 17025 calibration certificate documents traceability for quality management systems and audit trails. Faster measurement workflows through integrated data transfer Data capture is simplified by the unit's Wireless and USB outputs, eliminating manual transcription and reducing logging errors. The 1.54" touchscreen display provides direct control and fast confirmation of values at the bench; simultaneous digital output supports direct interfacing with SPC software or dataloggers. For production environments where throughput and documentation count, this configuration shortens inspection cycles and integrates measurement results into existing quality workflows without additional adapters. Robust design and user advantages for everyday metrology Built for industrial use, the micrometer combines a sturdy contact geometry with a digital readout to balance handling and precision. The disc-measuring faces offer broader support on profiles and permit more consistent pressure distribution during contact. The instrument's digital electronics stabilise readings, filtering operator variation so that mechanical skill becomes less of a limiting factor. Maintenance is straightforward: the mechanical parts are accessible and the electronic interface is designed for reliable shop-floor operation, contributing to long-term uptime and consistent measurement quality. Where this instrument is best applied The device suits applications requiring external dimensional checks on medium to large components — for example, bearing housings, large shafts, and mounted fixtures. With ISO 17025 calibration supplied, the tool is ready for use in traceability-critical environments such as incoming inspection, first-off checks and final part release. The combination of broad anvils, a non-rotating spindle and digital output also makes it useful for serial sampling where consistent contact and rapid data collection are priorities. Secure traceable measurements with Microtech Metrology’s ISO 17025-calibrated micrometer — contact Metav Werkzeuge for procurement details and application support Technical data Article number: 110783757 GTIN: 4061905457586 ECLASS: 21170328 ETIM: EC003590 Manufacturer: Microtech Metrology Facts Measuring range: 350–375 mm Accuracy: ±0.009 mm Display: Touchscreen 1.54" Measuring faces: Disc Ø35 mm Data output: Wireless + USB Digital instrument: yes Non-rotating spindle: yes Special features ISO 17025 calibration certificate included Large disc anvils for stable contact Wireless and USB connectivity for data logging Touchscreen interface for quick operation Designed for industrial shop-floor use FAQ What calibration documentation is supplied with this micrometer? The micrometer is delivered with an ISO 17025 calibration certificate, confirming traceability and laboratory-level calibration. How are measurements exported from the device? Measurement values can be transmitted via Wireless or USB outputs for direct capture into SPC systems or data-logging software. What level of accuracy can be expected for large-part checks? The instrument is specified to ±0.009 mm, making it suitable for many production and inspection tasks where sub-hundredth-millimetre precision is required. Are the measuring faces suitable for rough or profiled surfaces? The Ø35 mm disc anvils distribute contact force over a larger area, improving stability on profiles compared with point-style anvils. Which SKU should be referenced when ordering or requesting documentation? Please reference SKU 110783757 when enquiring about the Microtech Metrology digital outside micrometer. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
350–375mm Thread Measuring Micrometer With 2.4" Colour Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Benefit from precise digital measurement, wireless data transfer and certified calibration for reliable thread inspection of large components; combine the 2.4" touchscreen, Wireless+USB connectivity and ISO 17025 traceable calibration for consistent production control. Order the Microtech Metrology thread micrometer Whitworth 55 directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology Thread Micrometer Whitworth 55 — Digital 2.4" Touchscreen, Wireless+USB The Microtech Metrology Thread Micrometer Whitworth 55 is a digital instrument for high‑accuracy measurement of Whitworth thread profiles, optimised for production and laboratory quality control tasks. Digital 2.4" colour touchscreen display Wireless and USB data interface Non‑rotating spindle for repeatability ISO 17025 calibrated with certificate Precision that supports reproducible decisions The instrument delivers accuracy ±0.009 mm and a fine resolution 0.0001 mm, which together reduce measurement uncertainty and support tighter process limits. Supplied fully calibrated to ISO 17025, the device arrives with a calibration certificate, enabling immediate use in quality assurance workflows and documented traceability for audits. The large measuring range of 350–375 mm makes the unit suitable for sizeable threaded components where standard micrometers would fall short. Data capture that accelerates inspection routines A 2.4" colour touchscreen provides clear readings and straightforward menu navigation for routine checks, while Wireless and USB outputs enable direct data export to inspection software or spreadsheets. The integrated electronics and microcomputer functions simplify logging of repeated measurements and reduce transcription errors, improving throughput and allowing rapid statistical evaluation of thread geometry in production lines. Mechanical design focused on repeatability The instrument incorporates a non‑rotating spindle to avoid thread distortion during measurement and comes with 10× anvils 60‑3.5 TPI for immediate compatibility with Whitworth 55 threads. Robust construction and thoughtful ergonomics ensure stable contact and consistent measuring force, translating into reliable repeatability across operators. These mechanical features make the device an effective tool for both workshop measurement and incoming inspection of threaded parts. Integration into industrial quality processes Designed for professional inspection, the micrometer supports documented quality control and easier handover between shopfloor and lab. The combination of digital readout, reliable mechanical design and certified calibration reduces rework and inspection time, helping to keep production running smoothly. As part of a broader quality strategy, the instrument complements established metrology sets and can be introduced without complex adjustments to existing measurement protocols. Contact Metav Werkzeuge for tailored advice on applying the Microtech Metrology thread micrometer in a production environment and to request the full specification sheet Technical data Article number: 110723508 GTIN: 4061905456992 Manufacturer: Microtech Metrology Type: Whitworth 55 thread micrometer Measuring range: 350–375 mm Facts Accuracy: 0.009 mm Resolution (reading): 0.0001 mm Display: 2.4" colour touchscreen Data output: Wireless + USB Included anvils: 10× Amboss 60‑3.5 TPI Special features Non‑rotating spindle for undistorted readings Delivered calibrated to ISO 17025 with certificate Digital microcomputer measurement functions Suitable for large threaded components and QC use FAQ Is the instrument delivered calibrated? Yes. The Microtech Metrology thread micrometer is supplied fully calibrated to ISO 17025 and includes a traceable calibration certificate. Which interfaces are available for data transfer? Measurement data can be transmitted wirelessly or via USB from the micrometer to PCs or data loggers for streamlined documentation. What measuring range does the device cover? The instrument covers a measuring range of 350–375 mm, intended for larger threaded parts and assemblies. Which thread form is supported by the supplied anvils? The supplied set includes 10× anvils for 60‑3.5 TPI, matching the Whitworth 55 thread specification. Can the touchscreen be used for basic statistics on the device? The 2.4" colour touchscreen provides clear measurement readouts and menu access; data export via Wireless or USB allows detailed analysis off‑device. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
350–400mm Bore Gauge Micrometer With Microcomputer Readout, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of extended measuring range, reliable digital data output and traceable ISO 17025 calibration for consistent quality control; order the instrument directly via Metav Werkzeuge or consult our experts for integration advice. Outside micrometer — Digital outside micrometer with Wireless+USB, 350–400 mm range (Microtech Metrology) The Outside micrometer is a digitally read outside micrometer intended for medium‑range measurements in workshop and production environments, offering wireless and USB data transfer for process integration. Digital micrometer, range 350–400 mm Wireless and USB data interface ISO 17025 calibration included 110 mm throat depth, Ø8 mm anvils Long reach with workshop-friendly handling This instrument is designed as a middle‑range measuring tool (300–500 mm class), giving access to larger components while retaining manageable handling and stiffness. The 350–400 mm measuring range provides coverage for medium‑sized fixtures, housings and assemblies where a standard micrometer would be too short. The modest throat depth of 110 mm increases versatility for parts with recessed surfaces, and the Ø8 mm measuring faces concentrate contact forces to produce repeatable readings. The practical design balances reach and rigidity so inspection routines remain efficient without introducing avoidable measurement uncertainty. Digital readings and seamless data workflow Equipped with a digital readout and Wireless+USB data output, the micrometer supports direct transfer of measurement values into quality software or SPC systems, reducing transcription errors and accelerating documentation. The device records values with a fine resolution of 0.0001 mm and a specified accuracy of ±0.009 mm, which together allow dependable pass/fail decisions and statistical process control in serial production. The combination of clear digital display and reliable interfaces makes the instrument suitable for traceable measurement chains and for environments that require swift digital logging. Traceable calibration and practical measurement features The tool is delivered with a full calibration certificate carried out to ISO 17025, ensuring results are traceable and accepted in formal inspection procedures; the certificate is included with the instrument. The digital design and robust measuring faces are intended for repetitive use in workshop and production settings, where consistent contact geometry matters. The micrometer’s features reduce the typical sources of operator‑induced variance: a stable anvil diameter and defined throat geometry help achieve reproducible seating on the workpiece. For organisations that demand documented accuracy and digital capture, this instrument aligns metrological performance with everyday usability. Speak with Metav Werkzeuge for tailored advice on integrating Microtech Metrology digital micrometers into the production workflow and to arrange delivery from our Emmerich stock Technical data Article number: 115054007 GTIN: 4061905040931 Eclass: 21170328 ETIM: EC003590 Manufacturer: Microtech Metrology ISO 17025 calibration: included Specifications Measurement range: 350–400 mm Resolution: 0.0001 mm Accuracy: ±0.009 mm Throat depth: 110 mm Anvil diameter: Ø8 mm Features Digital readout Wireless and USB data output Classified as middle‑range (300–500 mm) Delivered with traceable calibration certificate Suitable for medium‑sized components and fixtures FAQ What measurement range does this instrument cover? The instrument covers a 350–400 mm measurement range, placing it in the middle‑range class suitable for medium‑sized components. Is a calibration certificate supplied with the micrometer? Yes, the micrometer is supplied with a traceable calibration certificate carried out to ISO 17025 standards. How are measurement values exported from the device? Measurement values can be exported via Wireless and USB interfaces for direct logging into quality and SPC systems. What precision and accuracy can be expected during inspections? The instrument offers a resolution of 0.0001 mm and an accuracy of ±0.009 mm, enabling reliable inspection results for workshop and production tasks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
35mm Digital Micrometer 0.001mm Resolution, 35mm Travel, Friction Stop, Data Output RB 6, Supplied in Case - Metav IndustryLine
Take advantage of a 0.001 mm display, a friction‑ratchet spindle and integrated RB 6 data output for fast, reliable thickness checks; compact design and hardened measuring faces ensure repeatable results — order directly via Metav Werkzeuge or request detailed advice from our consultants. Digital Micrometer M302.081 – 0–35 mm, 0.001 mm resolution, RB 6 data output (Metav IndustryLine) The Digital Micrometer M302.081 is a compact, high‑resolution measuring instrument for precision thickness and diameter checks in workshops and quality control labs, optimised for fine mechanical components and repeatable measurements. 0.001 mm resolution display 35 mm measuring range Friction ratchet spindle control RB 6 data output interface Reduce rework with traceable, high‑resolution readings The instrument delivers a resolution of 0.001 mm combined with an application accuracy of approximately ±0.006 mm, enabling operators to identify deviations that would be missed by coarser gauges. The electronic readout, featuring ON/OFF/SET, DATA and mm/inch/0 functions, simplifies routine inspections and reduces transcription errors. Where process stability matters, the integrated RB 6 data output allows direct transfer of readings into data acquisition systems, speeding up quality reports and minimizing manual logging. Fast, consistent contact control for delicate parts A built‑in friction ratchet provides a reproducible measuring force, protecting delicate components and ensuring consistent contact pressure from measurement to measurement. The spindle control combined with hardened measuring faces of 6.5 mm diameter gives both durability and gentle handling of small parts. Delivered in a protective case, the instrument is ready for workshop use and storage, reducing risk during transport and prolonging service life. Compact range, ideal for micro applications Classified in the micro range for its 0–35 mm span, this micrometer is tailored to fine mechanical and precision‑engineering tasks such as watch components, small housings and precision shafts. Its modest weight and compact frame make it easy to handle while providing the stiffness required for accurate single‑handed operation. The design therefore balances reach, rigidity and repeatability, delivering practical advantages for labs and production benches that demand reliable sub‑millimetre control. For reliable, traceable measuring workflows with Metav IndustryLine precision, contact Metav Werkzeuge for specification support and order guidance — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M302.081 GTIN: 4054469168852 Category: Messschrauben Label: Digital‑Micrometer, 0 - 35 mm, friction ratchet, 0.001 mm reading; data output RB 6 UID: M302.081 Numbers / Core technical data Measuring range: 0–35 mm Resolution: 0.001 mm Nominal accuracy: ±0.006 mm Measuring face diameter: 6.5 mm Weight: 0.5 kg Measuring stroke / travel: 35 mm Special features / Versions Digital display with ON/OFF/SET, DATA and mm/inch/0 buttons Friction ratchet spindle control Data output: RB 6 interface Hardened measuring faces Supplied in protective case Designed for fine mechanical and workshop use Digital instrument (electronic readout) FAQ How precise is the measurement with this micrometer? The micrometer offers a resolution of 0.001 mm and an application accuracy around ±0.006 mm, which supports fine tolerancing in inspection and production environments. Can measurement data be transferred electronically? Yes, the instrument includes an RB 6 data output for direct transfer of readings to data collection systems, enabling straightforward integration into quality documentation workflows. Is the contact force reproducible when measuring sensitive parts? The integrated friction ratchet ensures consistent contact pressure, reducing measurement scatter and protecting delicate components during inspection. What measuring range and applications suit this micrometer? With a 0–35 mm range it falls into the micro class, ideal for fine mechanical parts, small housings and precision shafts where compactness and accuracy are essential. Does the micrometer come ready for workshop use and transport? Yes, the instrument is supplied in a protective case to facilitate safe transport and storage, helping to preserve calibration and instrument condition. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
35–70 mm Digital Micrometer 0.001 mm Resolution Friction Ratchet, RB6 Data Output - Metav IndustryLine
Combining 0.001 mm resolution, a friction ratchet for consistent measuring force and an RB 6 data output for easy integration, this micrometer delivers reliable, traceable measurements for production and inspection. Order the Digital micrometer 35–70 mm directly via Metav Werkzeuge or ask our consultants if needed. Digital micrometer M302.082 — precision digital micrometer, 35–70 mm, 0.001 mm resolution (Metav IndustryLine) A Digital micrometer 35–70 mm engineered for repeatable high‑precision measurements in workshop and quality‑control environments. High‑resolution 0.001 mm display Friction ratchet for repeatable force RB 6 data interface for traceability Hardened 6.5 mm measuring faces Precision and repeatable results for quality control The instrument offers a measuring range of 35–70 mm with a display resolution of 0.001 mm, combined with a stated accuracy of ±0.007 mm, delivering the control expected in routine inspection tasks. The integrated friction ratchet standardises applied measuring force, reducing operator influence and improving reproducibility across repeated measurements. Such specification supports faster decision making on the shop floor and reduces the need for time‑consuming rechecks or corrective work. Seamless data capture to speed up workflows Equipped with an RB 6 data output and a multifunction digital display (ON/OFF/SET, DATA, mm/inch/zero), the gauge simplifies documentation and process integration. The serial interface enables direct transfer of measured values into inspection reports or SPC software, cutting manual transcription and the associated risk of errors. For production lines where traceability is essential, this capability translates into measurable time savings and improved audit readiness. Robust design for everyday use Built for regular handling, the device incorporates hardened measuring faces Ø 6.5 mm and a measuring travel of 35 mm that suits a wide range of components. The construction balances stiffness and portability — with a weight of about 0.6 kg — so the instrument is substantial enough for stable contact yet easy to manoeuvre in confined workstations. The digital mechanism and tactile ratchet together support confident, fatigue‑reduced operation during extended measuring tasks. Practical benefits and workshop fit As a precision measuring tool from Metav IndustryLine, the unit bridges bench and production environments by offering both fine resolution and pragmatic handling features. The compact profile and standardised output make the instrument suitable for incoming inspection, in‑process checks and final QA. The combination of high resolution, standardised measuring force and data connectivity offers a direct productivity advantage where consistent dimensional control matters. Request a specification sheet or technical consultation from Metav Werkzeuge to determine how the Metav IndustryLine digital micrometer M302.082 can be integrated into existing inspection routines Technical data SKU: M302.082 GTIN: 4054469168869 Tariff number: 90173000 Numerical data Measuring range: 35–70 mm Resolution: 0.001 mm Accuracy: ±0.007 mm Measuring faces diameter: 6.5 mm Measuring travel: 35 mm Weight: 0.6 kg Features Digital display functions: ON/OFF/SET, DATA, mm/inch, 0 Data output: RB 6 Friction ratchet for consistent measuring force Hardened measuring faces Category: Micrometers (Messschrauben) FAQ What is the measuring range and resolution of this micrometer? The micrometer covers 35–70 mm with a resolution of 0.001 mm, allowing fine incremental readings for accurate inspection tasks. Does the instrument provide a data output for integration with software? Yes, the device includes an RB 6 data output so measured values can be transferred directly into SPC systems or inspection software. Is the measuring force standardised to improve repeatability? The integrated friction ratchet ensures a constant measuring force, which improves repeatability and reduces operator‑related variation. What materials are the measuring faces made from? The gauge features hardened measuring faces with a 6.5 mm contact diameter, designed for durability during routine use. Which product and brand does the FAQ refer to? These answers refer to the Metav IndustryLine Digital micrometer M302.082, a precision micrometer intended for workshop and QA applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
375-400mm Gauge Micrometer With Colour 2.4" Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of an industrial-grade micrometer that combines high repeatability, ISO 17025 calibration and modern data transfer to streamline inspection of medium‑sized components; order the calibrated instrument directly via Metav Werkzeuge or consult our specialists for integration into existing quality routines. Electronic Screw Micrometer — Wireless + USB, 2.4" Colour Touchscreen (Microtech Metrology) Micrometer for precision thread and length measurement in production inspection and metrology labs, offering digital readout and traceable calibration for reliable batch control ISO 17025 calibration certificate included Wireless and USB data output 2.4" colour touchscreen display Measurement range up to 400 mm Resolution / accuracy 0.01 mm Precise measurement for medium-range components that must be repeatable This measuring instrument is designed for medium‑range tasks with a measurement range of 375–400 mm, making it suitable for fixtures, mould parts and larger assemblies where stiffness and reach must be balanced. The non‑rotating spindle reduces surface marking and ensures consistent contact geometry; combined with an accuracy of 0.01 mm, this provides a reliable basis for statistical process control. The supplied set of six anvils (0.4–7 mm, Metric 60) extends practical use for different thread profiles without delaying inspection cycles. Digital data capture that speeds up inspection and reduces transcription errors Integrated Wireless and USB data outputs enable direct transfer of measured values into inspection software or spreadsheets, cutting manual entry and accelerating batch documentation. The 2.4" colour touchscreen presents readings and menus clearly, so measurement routines run faster and training times are reduced. Because the instrument is delivered with an ISO 17025 calibration certificate, traceability is maintained from the first measurement; this supports audit requirements and reduces administrative friction when results must be archived. Built for repeatability, traceability and shop‑floor resilience Constructed for regular use in production environments, the device features a robust design and a spindle that is specified not to rotate, which helps preserve repeatability during successive measurements. The Metric 60 thread type and included anvils facilitate thread inspection without additional tooling changes. Supplied as a fully calibrated measuring instrument, it provides immediate, documented accuracy for incoming inspection, in‑process checks or final quality control while reducing uncertainty in measurement data. Order the ISO 17025‑calibrated micrometer from Microtech Metrology via Metav Werkzeuge — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 110714008 GTIN: 4061905457227 Manufacturer: Microtech Metrology Display: Colour 2.4" touchscreen Data output: Wireless and USB Accessories included: 6x anvils 0.4–7 mm (Metric 60) Facts Measurement range: 375–400 mm Resolution / accuracy: 0.01 mm Digital instrument: yes Calibration: ISO 17025 certificate included Special features Non‑rotating spindle Metric 60 thread type Delivered with calibration certificate (ISO 17025) Wireless + USB connectivity Colour touch display for simplified operation FAQ Is the instrument delivered calibrated and traceable? Yes. The micrometer from Microtech Metrology is supplied fully calibrated with an ISO 17025 calibration certificate, ensuring traceability for audit and quality control purposes. How are measurement results transferred to a PC or inspection system? Measured values can be exported via Wireless or USB; the micrometer supports direct data transfer to reporting software to reduce manual transcription. What measurement range does this instrument cover and for which applications is it suitable? The device covers 375–400 mm, placing it in the medium‑range class suitable for larger fixtures, mould components and assembly parts where a balance of reach and stiffness is required. Are accessories included for thread inspection? Yes. Six anvils (0.4–7 mm, Metric 60) are included to support common thread profiles without immediate need for additional tooling. What level of accuracy can be expected for routine inspections? The micrometer provides a resolution and specified accuracy of 0.01 mm, appropriate for industrial inspection and process control where repeatable dimensional data are required. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
375-400mm Precision Micrometer With 35mm Disc Measuring Faces, Touchscreen Readout, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of ISO 17025 calibration, high measurement consistency and integrated wireless data transfer for reliable inspection workflows; the delivered calibration certificate supports traceable quality assurance. Order the micrometer directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology Micrometer – 375–400 mm, ISO 17025 calibrated, Wireless+USB The Micrometer is a medium-range measuring instrument for larger assemblies and fixture inspection, combining a 375–400 mm measuring span with touchscreen readout and wired/wireless data output. ISO 17025 calibration with certificate Wireless+USB data output for digitised workflows Touchscreen 1.54" display for clear readouts Large Teller measuring faces Ø35 mm for stable contact Precise, traceable measuring for medium-range components This measuring instrument delivers consistent results across its 375–400 mm span and is supplied fully calibrated to ISO 17025, with a calibration certificate included for immediate use in quality-controlled environments. The device achieves an accuracy of ±0.009 mm, which positions it between standard workshop tools and laboratory-grade instruments; this level of precision reduces rework and supports reproducible inspection records. Classification as a medium-range micrometer highlights its suitability for assembly and mould-making tasks where reach and stiffness must be balanced. Faster data capture and error reduction through digital output Integrated Wireless+USB data output and a Touchscreen 1.54" display streamline measurement capture and logging. Digital transmission removes manual transcription steps, reducing human error and accelerating quality-control throughput. The touchscreen readout presents values with improved legibility compared with analogue scales, while the digital interface supports direct connection to inspection software and SPC systems, enabling immediate evaluation and archiving of measurement series for traceability and process improvement. Robust contact geometry and handling for reliable results The device features Teller Ø35 mm measuring faces and a non-rotating spindle that maintains parallelism and prevents marking of delicate surfaces during closure. Large-faced anvils distribute contact pressure more evenly on irregular or thin-walled parts, increasing repeatability when measuring housings, flanges or assembled components. The mechanical design focuses on operator ergonomics and measurement consistency, helping to reduce variability in repetitive checks and to integrate smoothly into standard workshop routines. Contact Metav Werkzeuge today for application advice and to secure the Microtech Metrology micrometer with ISO 17025 calibration and Wireless+USB data output Technical data Article number: 110784007 GTIN: 4061905457593 Manufacturer: Microtech Metrology Facts Measuring range: 375–400 mm Resolution/readout: 0.0001 Accuracy: 0.009 mm Display: Touchscreen 1.54" Data output: Wireless+USB Calibration: ISO 17025, certificate included Special features Digital micrometer with touchscreen readout Large Teller measuring faces Ø35 mm Non-rotating measuring spindle Delivered calibrated and traceable FAQ Is the micrometer delivered with a calibration certificate? Yes. The micrometer is supplied fully calibrated to ISO 17025 and includes a calibration certificate for traceable quality documentation. How are measurement results exported from this instrument? Measurement data can be transmitted via Wireless and USB interfaces, allowing the micrometer to feed values directly into inspection software or data-logging systems. What measuring span and accuracy does this device offer? The instrument covers a measuring range of 375–400 mm and provides an accuracy of ±0.009 mm, suitable for medium-range inspection tasks. Are the measuring faces suitable for irregular or thin-walled parts? The large Teller measuring faces (Ø35 mm) are designed to distribute contact pressure and improve repeatability when measuring irregular or thin-walled components. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
375-400mm Thread Micrometer Digital Wireless+USB Color 2.4" Touchscreen, ISO 17025 Calibrated – Microtech Metrology
Combine ISO 17025 traceability, a colour touchscreen and wireless data transfer to streamline thread inspection and documentation. Benefit from a calibrated instrument with included Whitworth anvils for immediate use; order directly via Metav Werkzeuge or consult our specialists for application advice. Micrometer — Thread micrometer with microcomputer and wireless USB (Microtech Metrology) A micrometer designed for industrial thread measurement, integrating a microcomputer and colour touchscreen for efficient inspection of Whitworth threads. Precision thread measurement with microcomputer Colour 2.4" touchscreen display Wireless and USB data output Delivered with ten 60-3.5 TPI Whitworth anvils Fast, traceable results for production control This measuring instrument brings together a digital control unit and high-resolution readout to accelerate inspection tasks in production and quality assurance. The integrated microcomputer evaluates thread forms and records measurements immediately, while wireless and USB connectivity removes transcription steps and reduces human error. With a display resolution down to 0.0001 mm and an operational accuracy of 0.01 mm, the device supports reliable decision-making at the control station and simplifies data capture for traceability workflows. Ready for inspection — calibrated and complete Delivered with a set of Whitworth anvils and a calibration certificate, the instrument is prepared for immediate use in laboratory and workshop environments. Calibration has been performed to ISO 17025 standards and the certificate is supplied, ensuring measurement results can be documented for audits or supplier acceptance. The combination of certified calibration and included accessories reduces setup time and provides clear evidence of conformity for internal quality systems. Designed for everyday industrial use Built for repetitive thread checks on medium-length components, the instrument’s 375–400 mm measuring span accommodates longer threaded parts while maintaining handling ergonomics. The 2.4" colour touchscreen offers an intuitive interface for selecting thread profiles and viewing measurement histories, lowering training time for operators. Robust data output options support integration into inspection software or simple export via USB, enabling a smooth transition from manual documentation to a digital quality record. For ISO-traceable thread measurement with wireless data capture and full calibration documentation, contact Metav Werkzeuge to secure this Microtech Metrology micrometer and arrange a tailored supply or technical consultation. Technical data Article number: 110724008 GTIN: 4061905457012 Manufacturer: Microtech Metrology Core specifications Measuring range: 375–400 mm Resolution (display): 0.0001 mm Accuracy: 0.01 mm Display: Colour 2.4" touchscreen Data output: Wireless + USB Features / Special characteristics Type: Whitworth 55 Includes: 10x anvils 60-3.5 TPI (Whitworth 55) Digital instrument with integrated microcomputer Calibration: ISO 17025 certificate included FAQ Is the instrument supplied calibrated to an accredited standard? Yes. The micrometer from Microtech Metrology is delivered fully calibrated with an ISO 17025 certificate included for traceable documentation. How are measurement results exported from the instrument? Measurement data can be transferred via the device’s wireless interface or via USB connection to inspection software or a PC for further processing. What thread types and sizes can be inspected with the supplied anvils? The delivery contains ten anvils for 60-3.5 TPI (Whitworth 55) threads; these are suitable for standard Whitworth inspection tasks as provided with the instrument. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
375mm Setting Gauge for Micrometre With Thermal Shielding, Ball Measuring Faces ±0.004mm - Metav IndustryLine
Take advantage of high-precision performance and thermal stabilisation to keep calibration routines fast and reproducible; the combination of a 375 mm nominal length and ±0.004 mm accuracy ensures stable setting for larger micrometre ranges. Order the setting standard directly via Metav Werkzeuge or consult our experts if further specifications are required. Micrometre Setting Standard M304.320.3 – 375 mm, accuracy ±0.004 mm (D 16 mm) by Metav IndustryLine The Micrometre Setting Standard M304.320.3 is a purpose-made reference gauge for setting and checking outside micrometres in workshop and laboratory environments. 375 mm nominal length for extended reach Accuracy ±0.004 mm for fine calibration Spherical measuring faces for repeatability Thermal protection for stable measurements Precision that reduces rework and inspection time The setting standard provides a clear metrological advantage through its ±0.004 mm declared accuracy, offering a reliable reference when adjusting outside micrometres or verifying measuring equipment. Using a dedicated reference gauge rather than informal standards reduces measurement uncertainty and accelerates setup procedures. The high-resolution specification supports targeted quality-control steps and contributes to a measurable reduction in downstream rework, as alignment and zeroing are achieved consistently and more rapidly. Stable readings despite thermal influences Integrated thermal protection keeps the effective measuring length stable during typical workshop conditions, mitigating drift caused by hand contact or ambient temperature shifts. The gauge’s spherical measuring faces ensure defined contact geometry, which improves repeatability when transferring a reference dimension to a micrometre spindle. These design choices combine to deliver usable readings sooner in a workflow, reducing pause time between measurements and enabling more predictable inspection throughput. Built for medium-range applications and easy handling With a nominal length of 375 mm, this reference falls into the medium range used for larger assemblies and fixture components, providing a balance between reach and rigidity. The tool’s nominal diameter 16 mm contact and compact mass support straightforward manipulation on the shop floor while maintaining profile stiffness for consistent results. As a dedicated accessory for micrometre adjustment, the gauge integrates naturally into machine-shop and metrology benches where reproducible external-diameter references are required. Practical benefits for quality workflows The setting standard functions as an efficient step in incoming inspection, setup and routine checks. By standardising the zero-setting process for external micrometres, it helps maintain traceable measurement chains and simplifies operator tasks. The accessory nature of the gauge makes it suitable for use alongside bench micrometres or portable instruments, offering a pragmatic way to raise everyday measurement confidence without complex procedures. For assured calibration stability, request the Metav IndustryLine Micrometre Setting Standard M304.320.3 via Metav Werkzeuge — Metav’s specialists in Emmerich can advise on fitment and delivery; contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M304.320.3 GTIN: 4054469116723 Tariff number: 90173000 Facts Nominal length: 375 mm Accuracy: ±0.004 mm (±4 µm) Weight: 0.6 kg Nominal diameter: 16 mm Special features Thermal protection Spherical measuring faces Accessory for setting outside micrometres Category: Measuring instruments – accessories eClass: 21170102 FAQ What is this gauge used for? The Micrometre Setting Standard M304.320.3 is intended as a reference for setting and checking outside micrometres and for routine dimensional checks in workshop and laboratory contexts. Does the setting standard include a calibration certificate? This listing does not declare a specific calibration certificate; for traceable calibration options and certificates, contact Metav Werkzeuge to arrange the appropriate documentation for the M304.320.3. Which micrometre ranges is it compatible with? The reference dimension and contact geometry make the M304.320.3 suitable for use with standard external micrometres across the corresponding measurement range; compatibility details can be confirmed with Metav Werkzeuge for specific instrument models. How does the thermal protection help in practice? Thermal protection reduces measurement drift caused by hand heat or ambient changes, so the M304.320.3 delivers more stable reference lengths during successive setting operations. Are the measuring faces hardened or specially finished? The gauge features spherical measuring faces designed for defined contact and repeatability; for detailed surface treatment or material specifications, please request technical datasheets from Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3mm Special Ball Tip For Indirect Gear Tooth-Thickness Measurement, Module 1.75 — Metav IndustryLine
Take advantage of a compact 3 mm measuring ball and module 1.75 compatibility combined with pairwise delivery for matched inspections; order the Special ball insert D 3 mm directly via Metav Werkzeuge or ask our consultants if needed. Special ball insert D 3 mm — accessory for indirect tooth-thickness measurement, module 1.75 (Metav IndustryLine) The Special ball insert D 3 mm is an accessory designed for indirect measurement of gear tooth thickness on components with module 1.75, ideal for integration into gear-checking setups and comparators. 3 mm measuring ball diameter Compatible with module 1.75 gears Supplied pairwise for matched checks Consistent tooth-thickness results with a defined contact geometry The compact measuring ball establishes a repeatable contact point for indirect tooth-thickness measurement, reducing variability caused by crown or flank differences. By using a precisely dimensioned 3 mm sphere, the contact radius becomes consistent across checks, which improves comparability between workpieces and inspection cycles. This approach is particularly effective when evaluating spur gears or small pinions where direct contact probes cannot access the groove reliably. The result is a measurable improvement in process control and fewer false rejections during batch inspection. Fast adaptation and reduced setup time for shop-floor inspection Supplied pairwise, the inserts are matched to facilitate quick exchange and balanced measurement across mating positions, so setups for gear checks run more smoothly. The small mass and compact form make mounting straightforward on common gear gauges and fixtures; lightweight construction minimises influence on the measuring head and shortens settling times. For production environments where throughput matters, the accessory supports efficient measurement routines while maintaining the required reproducibility. Clear evidence for quality assurance and traceable inspection routines As part of the Metav IndustryLine portfolio, this measuring accessory contributes to a traceable inspection chain and aligns with workshop-level quality concepts. The defined module 1.75 specification and precise 3 mm diameter enable reliable documentation of measurement procedures and support repeatable results during routine audits. When combined with calibrated measuring equipment, the use of matched ball inserts helps to reduce operator-dependent scatter and strengthens confidence in acceptance decisions for gear parts. For matched inserts and application advice from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss suitability for specific gear types and inspection rigs Technical data SKU: M309.185 GTIN: 4054469118628 ECLASS: 21170324 Key measurements Ball diameter: 3 mm Module: 1.75 Weight: 0.1 kg Tariff number: 90173000 Special features Supplied pairwise For indirect tooth-thickness measurement Category: Measuring devices › Accessories Intended as accessory for gear inspection FAQ What is the primary application of this insert? The Special ball insert D 3 mm (SKU M309.185) is intended for indirect measurement of gear tooth thickness on components specified for module 1.75. Can the insert be used on different gear modules? The insert is manufactured for module 1.75 applications; for other modules, matching inserts with the appropriate ball diameter should be selected to maintain measurement accuracy. How is the insert supplied and handled during inspection? The item is supplied pairwise to allow matched checks; the paired delivery supports balanced measurement positions and straightforward replacement during inspection cycles. Does the insert change the measurement procedure compared with direct probes? Using a ball insert for indirect checks shifts the contact geometry; this provides reliable, repeatable contact points where direct probes cannot reach, improving comparability across similar parts. Is this accessory suitable for use on production metrology benches? Yes, the insert is designed as a precision accessory for gear inspection rigs and comparators; its compact form supports fast adaptation on shop-floor metrology setups. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3mm Three-Point Internal Micrometer Touchscreen, ISO 17025 Calibrated Wireless USB - Microtech Metrology
Take advantage of a compact, digitally driven measuring instrument that combines three-point contact stability with modern data transfer for faster inspection cycles; supplied calibrated to ISO 17025 with a traceable certificate and available directly from Metav Werkzeuge for prompt delivery. Three-point internal micrometer — Microtech Metrology, 2.0–3.0 mm range, colour touchscreen The Three-point internal micrometer is a micro-range instrument designed for precision measurement of small internal diameters in fine mechanical and watchmaking applications, delivering centred contact and high repeatability in confined bores. Compact micro-range 2.0–3.0 mm measurement Colour 1.5" touchscreen display Wireless and USB data output Delivered calibrated to ISO 17025 with certificate Precision where small tolerances matter The instrument is engineered for measurement tasks that demand reliable centring and minimal operator influence. The three-point contact geometry spreads the support evenly around the bore, reducing eccentricity and providing a stable reference for readings in the Micro range (2–3 mm). With a measuring depth of 12.5 mm, the gauge reaches shallow internal features while keeping the sensing geometry short and stiff — a decisive advantage when working on miniature components where even slight lever effects cause error. Streamlined recording and traceability An integrated microcomputer works with a 1.5" colour touchscreen display to present readings clearly and to reduce interpretation errors; the unit supports Wireless + USB data output for direct transfer into SPC systems or inspection reports. This connectivity shortens the feedback loop between shop floor and quality control, supporting rational decision-making and faster corrective action when measurements deviate from tolerances. Ready for inspection — calibrated and complete The tool is supplied as a set of two pieces and is delivered fully calibrated under ISO 17025, including a calibration certificate for immediate use in accredited inspection processes. This formal traceability removes an additional procurement step and supports documented quality assurance, which is particularly important for suppliers and manufacturers who must demonstrate conformity during audits. Built for dependable workshop integration Selected where space, repeatability and traceable results are priorities, this gauge reduces measurement variability and streamlines routine inspection workflows. The digital readout and data interfaces combine to lower recording errors and speed up batch acceptance, while the compact design and short measuring depth minimise handling time. For shops aiming to raise first-pass yield and maintain consistent part quality, this compact, calibrated instrument offers a pragmatic investment in measurement certainty. For a supply proposal, technical briefing or to arrange delivery via Metav Werkzeuge in Emmerich, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s team can advise on integration and traceability requirements Technical data Article number: 133700203 GTIN: 4061905074349 Manufacturer: Microtech Metrology Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Measuring range: 2.0–3.0 mm Measuring depth: 12.5 mm Set: 2 pieces per set Digital: yes Facts Measuring range min: 2.0 mm Measuring range max: 3.0 mm Measuring depth: 12.5 mm Pieces per set: 2 Display size: 1.5" Special features Three-point internal measurement geometry Integrated microcomputer Delivered calibrated to ISO 17025 Calibration certificate included Wireless and USB data interfaces Compact design for micro applications FAQ Is the instrument ready for use in accredited inspections? Yes. The three-point internal micrometer is delivered fully calibrated under ISO 17025 and includes a calibration certificate suitable for accredited inspection records. What measuring range does this gauge cover? The instrument measures internal diameters from 2.0 to 3.0 mm, a Micro classification suited for very small bores and fine mechanical parts. Does the device provide digital data output for SPC systems? Yes. The unit offers Wireless + USB connections to export measurements directly to data collection or SPC software. How many gauges are supplied in the set? This product is supplied as a set of two, allowing rapid tool changes or immediate redundancy for process checks. Is the display suitable for shop-floor use? The 1.5" colour touchscreen provides legible readings and simple menu navigation, designed for robust, practical use in inspection environments. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
3–4mm Internal Micrometer With Carbide Measuring Faces, Calibration Ring Included, Plastic Case - Metav IndustryLine
Take advantage of a compact internal micrometer that combines high repeatability, carbide measuring faces and a dedicated 4 mm setting ring for reliable small‑bore inspection; order the instrument directly via Metav Werkzeuge or consult the technical team for application advice. M312.127 internal micrometer – carbide measuring faces, 3–4 mm range (Metav IndustryLine) The M312.127 is an inside micrometer designed for precision measurement of small bores and blind holes in fine mechanical and precision engineering applications. Carbide measuring faces for long life Measuring range 3.0–4.0 mm Supplied with setting ring and case Precise measurement where millimetres matter This inside micrometer is optimised for compact bores: the 3–4 mm measuring range targets fine mechanical tasks where control over small dimensions is decisive. With an accuracy of ±0.004 mm, the instrument bridges typical workshop requirements and higher‑precision inspection tasks, reducing the need for subsequent rework. The mechanical vernier readout offers an immediately interpretable result without electronic dependency, which simplifies routine checks while delivering consistently measurable outcomes. Durable contact surfaces and robust scale for repeatable readings Long service life is achieved through the carbide measuring faces, which resist wear when used repeatedly in production or inspection environments. The matt chrome‑plated scale and vernier improve contrast and lower glare for reliable reading, while the included setting ring (4 mm) allows quick verification of zero and simple calibration against a reference. Supplied in a protective case, the instrument is ready for transport and secure storage, preserving measurement stability between uses. Integrating a micro‑range tool into quality processes Classified as a micro‑range internal measuring instrument, this micrometer is particularly suitable for blind‑hole measurement tasks in component assembly and toolmaking. The compact design and focused range support fast sampling plans in production and precise spot checks during final inspection, contributing to shorter inspection cycles and improved throughput. Metav IndustryLine’s selective range ensures accessibility of precision tools for workshops and specialist manufacturers alike, combining practical usability with traceable performance attributes. Choose the Metav IndustryLine M312.127 for dependable micro‑range internal measurement; contact Metav Werkzeuge for tailored application guidance or to arrange your purchase Technical data Article number: M312.127 GTIN: 4054469119403 Eclass: 21170335 Tariff number: 90173000 Core measurements Measuring range: 3.0–4.0 mm Accuracy: ±0.004 mm Setting ring: 4 mm Readout: analog (vernier) Materials & features Measuring faces: carbide Scale and vernier: matt chrome‑plated Supplied with setting ring Supplied in protective case Suitable for blind‑hole measurement Category: internal micrometer (inside measuring instrument) FAQ What level of accuracy can be expected from this instrument? The M312.127 delivers an accuracy of ±0.004 mm, making it suitable for high‑precision internal measurements in fine mechanical and inspection tasks. Is the micrometer suitable for blind‑hole (sack‑hole) measurement? Yes, the instrument is designed for blind‑hole measurement and is supplied with a setting ring that facilitates secure contact and correct depth positioning. What materials are used for the measuring faces and scale? Measuring faces are made of carbide for wear resistance; the scale and vernier are matt chrome‑plated to aid legibility and reduce reflection. Does the delivery include accessories for verification and storage? The product is supplied with a 4 mm setting ring and a protective case for transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
3–6 mm Internal Bore Gauge Set 0.001 mm Resolution, Includes Setting Rings And Extension, In Case - Metav IndustryLine
Reliable internal measurement for small diameters is achieved with a fine 0.001 mm graduation and a typical accuracy of ±0.004 mm; the compact design, hardened measuring faces and supplied setting rings ensure consistent results in workshop and production inspections — order the set directly via Metav Werkzeuge or consult our advisors for specification checks. M312.173 Internal Measuring Set — 3–6 mm, 0.001 mm resolution (Metav IndustryLine) M312.173 is a compact internal measuring set for precise inspection of small bores and blind holes in production and workshop environments 0.001 mm graduation for fine resolution Accuracy ±0.004 mm for reliable results Includes setting rings and extension Delivered in protective transport case Precision where repeatability matters The M312.173 internal measuring set provides metrology-grade resolution of 0.001 mm combined with a practical industrial accuracy of ±0.004 mm, making it suitable for tight tolerances in small-bore work. The instrument uses an analog vernier on a matt-chromed scale, which offers tactile, dependable readings without dependency on electronics; this is an advantage in harsh workshop conditions and simplifies long-term serviceability. The set’s compact measuring span concentrates stiffness where it is needed, improving repeatability during routine quality checks. Designed for blind-hole inspection and constrained bores Engineered specifically for internal diameters and blind-hole applications, the set includes setting rings (4 mm, 5 mm, 6 mm) and an extension to adapt to varying depths. These accessories enable quick on-bench calibration and transfer of reference values, supporting efficient quality control workflows. The geometry of the measuring anvils and the narrow range of the instruments reduce the risk of tilt in small bores, which means fewer re-measurements and a faster inspection loop in serial production. Robust construction for everyday workshop use The instruments feature hardened measuring faces and an analog mechanical design that resists shock and contamination compared with delicate electronic alternatives. The transport case supplied protects the set during storage and transit; its form factor is practical for workshop tool trolleys and the bench. The matt-chromed scale and vernier resist glare and are easy to read under typical workshop lighting, helping operators maintain consistent measuring technique and minimising reading error. Practical set-up and integration into inspection routines As a three-piece set, this equipment covers the common small-bore range while keeping inventory compact and manageable. The included extension and setting rings allow calibration against a traceable master before measurement, reducing setup time at the machine or inspection bench. Backed by the Metav IndustryLine range, the set fits into broader workshop provisioning strategies that prioritise robust tools and short delivery turnarounds, helping to streamline procurement and spare-part planning. Contact Metav Werkzeuge to request a technical specification check, a tailored quotation or further detail from our Emmerich team by email or phone Technical data Article number: M312.173 GTIN: 4054469119809 Category: Messgeräte / Messschrauben Manufacturer: Metav IndustryLine Facts Measuring range: 3–6 mm Resolution: 0.001 mm Accuracy: ±0.004 mm Pieces per set: 3 Weight: 1.3 kg Special features Analog reading with matt-chromed scale and vernier Hardened measuring faces Suitable for blind-hole measurements Includes setting rings (4, 5, 6 mm) and extension Supplied in transport case FAQ How precise is the M312.173 internal measuring set? The M312.173 delivers a reading resolution of 0.001 mm with an operational accuracy around ±0.004 mm, suitable for fine internal diameter control in production environments. Can this set be used for blind-hole measurements? Yes, the set is explicitly suitable for blind-hole measurement and includes setting rings and an extension to facilitate accurate checks at depth. Are the measuring surfaces durable? The measuring faces are hardened to provide wear resistance and repeatable contact, while the matt-chromed scale improves legibility and corrosion resistance. What type of reading does the set use and how is it interpreted? The instruments use an analog vernier on a matt-chromed scale with 0.001 mm graduation; interpretation follows standard vernier-reading technique for fine resolution. What is included in the delivery of the set? Delivery comprises three measuring instruments, setting rings (4 mm, 5 mm, 6 mm), an extension and a protective transport case Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4 mm Special Ball Insert For Indirect Gear Tooth Thickness Measurement, Module 2.25 - Metav IndustryLine
Take advantage of a dedicated measurement accessory that matches module 2.25 gears: the compact 4 mm ball geometry combined with paired delivery ensures reproducible indirect tooth‑thickness checks and reliable batch comparisons. Order the accessory directly via Metav Werkzeuge or contact the consultants for compatibility advice. Special ball insert D = 4 mm (module 2.25) – Gear measurement accessory by Metav IndustryLine The Special ball insert D = 4 mm for indirect gear tooth thickness measurement; module 2.25 is a purpose-built measuring tip intended for use as a matched pair in indirect evaluation of gear tooth thickness on module 2.25 gears. 4 mm ball diameter for module 2.25 Supplied in pairs for consistent readings Compatible with indirect tooth-thickness measuring methods Reliable indirect tooth-thickness evaluation with repeatable contact geometry The insert provides a defined contact point that reproduces the intended inspection geometry for indirect measurement of tooth thickness on module 2.25 gears. By employing a small, accurately shaped ball tip, the accessory minimises measurement uncertainty associated with variable contact points and allows comparative checks without requiring direct tooth-probing tools. This approach shortens inspection routines while maintaining traceable reproducibility between measurement cycles. Matched delivery for consistent comparative measurements Delivered as a matched pair, the inserts are intended to be used together to preserve symmetry in successive measurements. Paired supply reduces scatter between left‑ and right‑hand checks and supports quick cross-validation of production batches. At a net weight of 0.1 kg for the set, the accessory is light enough for straightforward handling yet substantial enough to seat reliably in typical gauge fixtures used for indirect gear evaluation. Easy to integrate into workshop and inspection fixtures The design is focused on simple retrofitting to existing toothed-wheel inspection rigs and comparative gauge jigs. The geometry of the tip aligns with standard indirect‑measurement procedures, so setup time is reduced and the measurement workflow becomes more efficient. This results in faster in‑process checks and a lower risk of production delays, supporting higher throughput in both small workshops and serial inspection environments. What to expect in practice and why it matters As a specialised accessory for module 2.25 gears, the insert supports consistent quality control and faster decision‑making on the shop floor. Using defined contact geometry and paired tips makes comparative assessments less dependent on operator technique, which helps to reduce rework and maintain steady output quality. For operations that demand reliable, repeatable tooth‑thickness data without complex retrofits, this accessory offers a pragmatic balance of functionality and simplicity. Choose the Metav IndustryLine accessory for assured compatibility with module 2.25 measuring processes — contact Metav Werkzeuge for detailed specification checks and ordering support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M309.187 GTIN: 4054469118642 Customs tariff number: 90173000 Facts Ball diameter: 4 mm Module: 2.25 Weight: 0.1 kg Special features Accessory for indirect gear tooth-thickness measurement Supplied in pairs for matched measurements Brand: Metav IndustryLine ECLASS: 21170324 FAQ How is the insert used for tooth-thickness checks? The insert is designed for indirect tooth‑thickness measurement; the Special ball insert D = 4 mm serves as a defined contact element in comparative gauge setups for module 2.25 gears. Are the inserts supplied individually or as a matched set? They are supplied as a matched pair to ensure consistent readings and symmetry across comparative measurements. Can this accessory be fitted to existing gauge fixtures? Yes, the geometry is intended for straightforward integration into standard indirect measurement jigs and comparative inspection fixtures for gears of module 2.25. Does the product include a calibration certificate? No calibration certificate is indicated in the product data; the Special ball insert D = 4 mm is delivered as an accessory for inspection setups and should be used within the calibration regime of the host gauge system. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5-3.5 TPI Thread Insert 55° Whitworth Style - Metav IndustryLine
Take advantage of the combination of precise Whitworth profile, workshop compatibility and compact handling to streamline thread verification tasks; order the Thread inserts M309.098.9 directly via Metav Werkzeuge or ask our consultants if needed. Thread inserts M309.098.9 — Thread gauge inserts, 4.5–3.5 TPI, 55° Whitworth (Metav IndustryLine) A set of Thread inserts M309.098.9 engineered for verification of Whitworth-form 55° threads in thread-gauging and measurement applications Precision 55° Whitworth profile Compatible with 4.5–3.5 TPI gauges Compact accessory for metrology rigs Accurate Whitworth profile for dependable thread verification The core benefit of these inserts is the 55° Whitworth profile, manufactured to match the historical Whitworth form used across legacy and specialist components. The geometry ensures a faithful mechanical reference when comparing threads against gauge spindles or working standards, reducing ambiguity during acceptance checks. Designed for gauge use in inspection benches, the inserts help convert a visual or tactile check into a repeatable measurement step. The specification 4.5–3.5 TPI is stated in threads per inch (TPI), a standard imperial descriptor; this range covers coarse Whitworth pitches commonly found in heavy fastenings and historical components, delivering clear identification during routine verification. Built for efficient workshop integration and faster inspections These inserts are an accessory tailored to fit established thread-measuring instruments and gauge adaptors, enabling quicker changeover and less downtime. The compact form and low mass facilitate handling in tight inspection setups and on small benches; the nominal weight of 0.1 kg keeps adapters balanced while in use. As an accessory for metrology workflows, the inserts support efficient inspection loops: align, engage, and verify. This translates into measurable time savings on repetitive checks and reduces cumulative measurement uncertainty caused by frequent component swaps. Compatibility and traceability to support quality control processes Supplied under the Metav IndustryLine designation, the inserts integrate into documented inspection routines and provide an identifiable article for audit trails. The clear marking with SKU M309.098.9 and GTIN ensures traceability in inventory and quality records, which simplifies procurement and batch control. For quality managers, the availability of a defined accessory that matches the Whitworth 55° form means fewer bespoke adjustments and a predictable verification outcome when used with thread gauges and measuring spindles commonly found in maintenance and restoration shops. Practical advantages for maintenance, restoration and specialised manufacturing In environments where Whitworth threads remain in service—such as vintage machine restoration, railway engineering or specialist plant maintenance—these inserts provide a pragmatic means to confirm thread form quickly without expensive bespoke fixtures. The accessory character makes it a cost-effective supplement to a metrology set-up: instead of reworking or trial-fitting components, the inserts enable a controlled check that supports decision-making — repair, refurbish or replace. Combined with Metav’s logistics and stock range, the parts are straightforward to source and integrate into a parts-management system. Contact Metav Werkzeuge for specification advice and to secure the M309.098.9 thread inserts for Whitworth 55° applications; assistance is available from Emmerich for product selection and delivery coordination Technical Data Article number: M309.098.9 GTIN: 4054469118406 Tariff number: 90173000 Facts Threads per inch: 4.5–3.5 TPI Thread angle: 55° Weight: 0.1 kg eCl@ss: 21170324 Special features Whitworth 55° profile Accessory for thread gauges / measuring instruments Category: Measuring devices — accessory FAQ What thread form do these inserts represent? The inserts represent the Whitworth 55° thread form and are manufactured to correspond with the historical Whitworth profile for reliable verification. Which TPI range is covered by the inserts? The inserts cover a 4.5–3.5 TPI range, stated in threads per inch for compatibility with imperial-thread gauges. Can these inserts be used with standard thread measuring spindles? Yes, the accessory is designed for use with thread gauges and measuring instruments that accept thread inserts for verification tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5-5.5mm Three-Point Internal Micrometer Self-Centring, Calibrated in Case - Metav IndustryLine
Take advantage of the combination of 0.005 mm measuring precision, a self‑centring three‑point design and hardened measuring faces for reliable bore inspection; order the instrument directly via Metav Werkzeuge or consult the technical team for application support. Three‑point internal micrometer M836.702 — Self‑centring design, 0.005 mm accuracy (Metav IndustryLine) The Three‑point internal micrometer M836.702 is a compact precision instrument for repeatable measurement of small internal diameters in fine mechanical and machining environments. Self‑centring three‑point design High accuracy 0.005 mm Hardened measuring faces Reduce rework with measurable accuracy The instrument delivers a certified mechanical accuracy of 0.005 mm, which translates into tighter tolerances during assembly and less rework on precision parts. By converting raw resolution into a clear production benefit, the micrometer shortens inspection loops and supports quality gates in machining workflows. The analog nonius readout provides a tactile feedback loop that experienced inspectors value for immediate verification, while the robust mechanical design maintains stable results under repeated use. Secure concentric measurements in small bores Designed as a three‑point, self‑centring device, the micrometer seats itself within the bore to establish a reproducible datum across measurements. This geometry reduces operator‑induced eccentricity and improves repeatability when inspecting small diameters in components such as valve seats, bushings or precision housings. With a measuring range of 4.5–5.5 mm and hardened measuring faces, the instrument is optimised for fine internal diameters where consistent contact geometry and surface resistance to wear are essential for long service life. Robust handling for everyday workshop use The mechanical construction emphasises longevity and simple maintenance: solid moving parts, a reliable spindle mechanism and clearly engraved scales make the tool suitable for daily use in both inspection benches and production cells. As an analogue micrometer with precise mechanical engineering, it performs without requiring batteries or electronics, which reduces maintenance points and keeps the inspection process straightforward. The combination of self‑centring functionality and hardened contact surfaces offers a practical, low‑complexity solution for high‑volume verification routines. For application advice or to equip a precision workshop with Metav IndustryLine instruments, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to secure this three‑point internal micrometer with proven 5 µm repeatability. Technical Data SKU: M836.702 GTIN: 4061905041259 Manufacturer: Metav IndustryLine ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 4.5–5.5 mm Accuracy: 0.005 mm Analog instrument (nonius) Hardened measuring faces Special features Self‑centring three‑point design Intended for internal diameter measurement Mechanical, maintenance‑friendly construction Suitable for fine mechanical and machining applications FAQ How precise is the instrument for routine inspections? The three‑point internal micrometer M836.702 provides an accuracy of 0.005 mm, offering the repeatability required for fine mechanical and machining quality control. What advantage does the self‑centring design bring? Self‑centring geometry ensures that the measuring tips align concentrically in the bore, improving repeatability and reducing operator‑related eccentricity when using the M836.702. Which diameter range is covered by this instrument? The micrometer covers a measuring range of 4.5–5.5 mm, making it suitable for very small internal diameters such as precision bores and small housings. Are the measuring faces durable for workshop conditions? Yes; the instrument features hardened measuring faces, which resist wear and preserve measurement accuracy over prolonged use. Is the device suitable for continuous production inspections? Its mechanical robustness and analogue nonius readout make the M836.702 well suited for repeated checks in production and bench inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5mm Special Ball Insert for Indirect Gear Tooth Thickness Measurement, Module 2.5 - Metav IndustryLine
Take advantage of the combination of precise contact geometry, module‑specific design and paired delivery for reliable gear tooth thickness checks; order directly via Metav Werkzeuge or consult our specialists for integration advice. Special ball insert Ø4.5 mm for indirect gear tooth thickness measurement (module 2.5) — Metav IndustryLine accessory The Special ball insert Ø4.5 mm is an accessory designed to enable indirect measurement of gear tooth thickness on module 2.5 gears, providing a compact solution for repeatable contact in workshop and inspection environments. Precision ball tip Ø4.5 mm for repeatable contact Designed for module 2.5 gear measurements Supplied in pairs for symmetrical evaluation Precise contact geometry for consistent indirect measurements The insert provides a defined spherical contact with a Ø 4.5 mm ball, which establishes a reproducible reference point when performing indirect tooth thickness checks on module 2.5 gears. By fixing the contact geometry, the insert reduces variability from ambiguous contact points and supports a predictable measurement result. The controlled contact improves process reliability and lowers the likelihood of rework in production or quality control tasks, making it suitable for routine workshop inspection as well as incoming goods checks. Streamlined workflow through pairing and compact design Delivered in pairs, the inserts enable symmetrical measurements and quick cross‑checks that accelerate decision making on component conformity. The compact format and low mass mean they are easy to exchange and store, reducing downtime during inspection cycles. As a dedicated accessory for gear metrology, the insert integrates into existing measuring fixtures and adapters used for tooth thickness evaluation, helping to maintain throughput without the need for complex fixturing changes. Clear applicability and practical handling advice Designed specifically for module 2.5 applications, the ball insert supports indirect measurement methods where a spherical probe approximates flank contact to derive tooth thickness via established geometric calculation. The defined Ø 4.5 mm diameter ensures correct flank engagement for the specified module, improving repeatability compared with ad‑hoc probes. Regular visual inspection and gentle cleaning with a lint‑free cloth will keep the contact surface in good condition and preserve measurement integrity. For detailed compatibility checks or to arrange supply of the Metav IndustryLine ball inserts, contact Metav Werkzeuge for technical advice and order processing at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M309.188 GTIN: 4054469118659 ECLASS: 21170324 Facts Module: 2.5 Ball diameter: 4.5 mm Weight: 0.1 kg Customs tariff number: 90173000 Special features Delivery: supplied in pairs Application: indirect tooth thickness measurement Category path: Measuring instruments › Accessories FAQ What is the primary use of this ball insert? The special ball insert Ø4.5 mm from Metav IndustryLine is intended for indirect measurement of gear tooth thickness on module 2.5 gears, providing a reproducible spherical contact for geometric evaluation. Is this insert suitable only for module 2.5 gears? The insert is designed specifically for module 2.5 applications; the Ø 4.5 mm ball diameter is selected to match the contact geometry required for that module. Why is the product supplied in pairs? Supplied in pairs to allow symmetrical measurements and fast cross‑checks; using both inserts helps validate measurement setup and reduces systematic measurement error. Which measuring equipment accepts this insert? The insert is compatible with measuring fixtures and gauge holders intended for gear tooth evaluation that accommodate exchangeable ball probes; the Metav IndustryLine insert is designed for straightforward integration into such setups. How should the insert be maintained? For best results, keep the ball surface clean and dry; wipe with a soft, lint‑free cloth and avoid aggressive solvents to preserve dimensional integrity of the contact sphere. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
4.5mm Three-Point Internal Micrometer Self-Centering, 0.005mm Accuracy, Supplied In Case - Metav IndustryLine
Benefit from a compact measuring instrument that combines a self‑centring three‑point measuring head, a ±0.005 mm declared accuracy and a fine 0.001 mm reading resolution for reliable internal diameter checks; supplied in a protective transport case. Order the three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer — self‑centring, 4.0–4.5 mm (Metav IndustryLine) Three‑point internal micrometer for precision internal diameter measurement in fine mechanical and quality‑control applications Self‑centring three‑point measuring head Accuracy ±0.005 mm Measuring range 4.0–4.5 mm Includes protective transport case Precise readings for narrow bores and fine parts The instrument offers a mechanical, analogue measuring principle combined with a fine reading step of 0.001 mm, enabling repeatable checks where small deviations matter. With a stated accuracy of ±0.005 mm, the tool is suited to inspection tasks that demand sub‑hundred‑micrometre consistency rather than coarse gauging. The analogue scale and thimble construction keep the device straightforward to operate while the fine graduation supports confident interpolations; this balance makes it efficient for workshop measurement cycles and quality‑control routines. Stable contact and centred measurement for reproducible results The self‑centring three‑point head ensures the contact points align concentrically in bore measurements, reducing operator‑induced eccentricity and improving reproducibility when compared with single‑point probes. Hardened measuring faces contribute to long service life and wear resistance, preserving the instrument’s metrological behaviour over repeated cycles. This geometry is particularly advantageous for small diameters and precision components in watchmaking, valve seats, bearing bores or similar fine‑mechanical work. Ready for the shop floor — protected and serviceable Delivered in a protective transport case, the micrometer is setup for safe storage and straightforward handling between jobs. The analogue construction minimises electronic dependencies and simplifies maintenance; routine checks and cleaning extend operational life without specialised tools. Backed by Metav IndustryLine’s quality control at the European distribution site, the instrument fits into an assured supply chain that supports steady production and dependable inspection throughput. For application advice or to confirm suitability for a particular component, contact Metav Werkzeuge to discuss the Metav IndustryLine three‑point internal micrometer (SKU M836.701) and arrange procurement or technical clarification. Technical data Article number: M836.701 GTIN: 4061905041242 Manufacturer: Metav IndustryLine ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 4.0–4.5 mm Resolution / reading: 0.001 mm Accuracy: ±0.005 mm Type: analogue internal micrometer Special features Self‑centring three‑point measuring head Hardened measuring faces Supplied in protective transport case Category: Micrometers / internal micrometer FAQ What is the measuring range of the instrument? The measuring range is 4.0–4.5 mm for this three‑point internal micrometer (Metav IndustryLine, SKU M836.701). How accurate is the device for internal measurements? Declared accuracy is ±0.005 mm; the instrument provides consistent internal diameter checks for fine mechanical tasks. Does the measuring head centre itself in the bore? Yes. The self‑centring three‑point measuring head centres within the bore to reduce eccentricity and improve reproducibility. Are the measuring faces wear‑resistant? The instrument is fitted with hardened measuring faces to enhance durability and preserve measurement stability over time. Is the micrometer supplied ready for transport and storage? The micrometer is delivered in a protective transport case to safeguard the instrument between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-100 mm Transport Case For Digital Three-Point Internal Micrometer - Metav IndustryLine
Take advantage of a compact storage solution that matches the 40–100 mm measuring range, keeps the related instruments together and is easy to handle at only 0.7 kg — a practical accessory for organised workshops. Order the case directly via Metav Werkzeuge or consult the technical team for compatibility details. Case for 312.218–312.222 (40–100 mm) — Metav IndustryLine protective case with compact handling Case for 312.218–312.222 (40–100 mm) designed as a dedicated transport and storage solution for matching measuring instruments, simplifying workshop logistics and instrument management Compatible with M312.218–M312.222 Designed for 40–100 mm instruments Lightweight at 0.7 kg for easy handling Secure storage that speeds up daily routines A dedicated storage solution for precision instruments improves turnaround and reduces handling time. The case for the M312.218–M312.222 series keeps the relevant tools organised, which speeds up changeovers and minimises the risk of misplacing small items. By consolidating instruments in one place, repeatability of measurement tasks is supported through consistent storage practices. The compact construction and modest 0.7 kg weight make the case simple to lift and position on workbenches or in tool trolleys, helping maintain an efficient workflow without adding unnecessary bulk. Compatibility and practical organisation for metrology workflows Compatibility with the 40–100 mm range means the case is purpose-built for a common segment of internal measuring instruments. Labelling and a clear item association reduce search time and support systematic inventory management. For workshops that prioritise traceability and rapid access, a product-focused container removes ambiguity between similar tool families, contributing to lean processes and predictable operational performance. This level of organisation complements existing calibration regimes and tool control measures, making daily quality checks and storage routines more reliable. Workshop resilience and supply-chain confidence Choosing a tailored accessory from an experienced supplier reduces procurement friction: parts and accessories arrive matched to instrument families and can be integrated into standard operating procedures immediately. Metav IndustryLine provides a steady supply chain and product consistency from its Emmerich hub, which functions as a European quality filter. This reliability supports continuous production and reduces the administrative overhead of sourcing ad hoc storage solutions, reinforcing predictable lead times and inventory control. For secure and compatible instrument storage choose the Metav IndustryLine case and contact Metav Werkzeuge for ordering or for advice on matching it to existing tool sets — info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M312.218.K GTIN: 4054469146829 Label: Koffer für 312.218-312.222 (40 - 100) 40 - 100 mm Numbers / Core technical data Weight: 0.7 kg Compatible measurement range: 40–100 mm Customs tariff number: 90173000 Special features / Design Suitable for articles M312.218–M312.222 Category: Accessories eClass: 21100103 FAQ Which instruments fit this case? The case is compatible with articles M312.218–M312.222, covering instruments with a 40–100 mm measuring range. What is the product SKU and GTIN? The SKU is M312.218.K and the GTIN is 4054469146829. How heavy is the case? The case weighs 0.7 kg, allowing easy handling and placement in workshops. How is the case classified? The item is listed under the accessories category (eClass 21100103) for measuring equipment. Which customs tariff applies? The customs tariff number for this item is 90173000. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-100mm Three-Point Internal Micrometer Self-Centering Set With Extensions, Plastic Case - Metav IndustryLine
Take advantage of the combination of high repeatability, compact standard range coverage and robust carbide measuring faces for reliable bore inspection in production and assembly. Order the three-point internal micrometer set directly via Metav Werkzeuge or consult the Metav advisers for application support. Three-point internal micrometer — Self-centring three-point design, 40–100 mm range (Metav IndustryLine) A three-point internal micrometer designed for precise bore measurement in workshop and inspection environments, offering a standard-range solution for routine engineering tasks. Self-centring three-point measuring principle Measurement range 40–100 mm Resolution 0.005 mm for fine reading Supplied in protective case, set of 6 Consistent bore measurement for production and inspection The three-point internal micrometer delivers repeatable internal diameters thanks to its self-centring measuring head and consistent contact geometry. The instrument is tailored for the standard measurement class (max. 100 mm), which balances reach and rigidity for everyday tasks in Machine and Metalwork. With a reading increment of 0.005 mm and an indicated accuracy of 0.006 mm, the device supports quality-control processes where tight tolerances and traceable repeatability are required. The three-point principle reduces the influence of off‑axis alignment, making readings more dependable on cylindrical and stepped bores. Robust contact surfaces and practical adjustment options Hardmetal measuring faces ensure long-term wear resistance and stable measurement results on typical workshop materials. The set includes setting rings at 50, 70 and 90 mm, enabling quick calibration across the working range and straightforward verification of the measuring chain. The analogue spindle and thimble mechanism give tactile feedback for fine positioning, while the compact construction aids ergonomic handling during repetitive checks. The combination of carbide faces and precise setting accessories reduces downtime for recalibration and keeps inspection cycles efficient. Designed for workshop efficiency and secure storage Delivered as a set with six pieces and protected in a transport case, the kit is arranged for fast selection and safe storage between shifts. The compact standard range size supports one-handed guidance without sacrificing stiffness, helping to maintain measurement integrity across multiple operators. For integration into established inspection routines, the instrument’s mechanical design minimises the need for frequent service while offering immediate visual confirmation of size changes. The product thus contributes to a streamlined production flow and reliable dimensional documentation. Contact Metav Werkzeuge today to secure this Metav IndustryLine three-point internal micrometer set (SKU M836.750) for dependable bore measurement — Metav’s consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 to advise on selection and application. Technical Data Article number: M836.750 GTIN: 4061905041396 Brand: Metav IndustryLine Facts Measurement range: 40–100 mm Minimum range: 40 mm Maximum range: 100 mm Resolution / reading: 0.005 mm Indicated accuracy: 0.006 mm Set contents: 6 pieces Setting rings: 50, 70, 90 mm Extension length: 150 mm Special features Self-centring three-point measuring head Carbide measuring faces for wear resistance Analogue instrument (non-digital) Delivered in protective case for transport Intended for internal diameter measurement ECLASS: 21170335 FAQ What measurement range is covered by this three-point internal micrometer set? The set covers internal diameters from 40 to 100 mm, making it suitable for standard workshop and machine‑building inspection tasks. Is the instrument suitable for routine quality control in a production line? Yes, the Metav IndustryLine three-point internal micrometer (SKU M836.750) offers a resolution of 0.005 mm and an indicated accuracy of 0.006 mm, which supports routine quality-control checks and repeatable measurements. How are calibration and setting handled for the micrometer? Calibration is performed using the supplied setting rings (50, 70, 90 mm) and the extension option of 150 mm; these accessories permit quick in‑house verification of the measuring chain. Are the measuring faces durable enough for workshop use? The measuring faces are made of hardmetal (carbide), which provides high wear resistance and long service life under normal workshop conditions. Can this instrument be used on stepped bores and standard cylindrical bores? The self-centring three-point design is optimised for both cylindrical and stepped internal geometries, improving centring and repeatability in typical bore inspection applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-32 TPI Thread Insert 55° Whitworth Profile - Metav IndustryLine
Take advantage of precise verification of Whitworth threads with a dedicated 40–32 TPI insert and a true 55° profile for repeatable checks. Durable, compact construction reduces handling error and supports consistent measurement routines. Order the M309.098.2 directly via Metav Werkzeuge or ask our consultants if needed. Gewinde‑Einsätze, 40 - 32 TPI, 55° — Thread insert for Whitworth 55° checks (Metav IndustryLine) Gewinde‑Einsätze, 40 - 32 TPI, 55° serve as a compact verification accessory for comparing or checking Whitworth 55° thread forms in workshop metrology, suited to precision inspection and gauge use 40–32 TPI Whitworth 55° compatibility Precision accessory for thread measurement Compact lightweight design, 0.1 kg Reliable verification of Whitworth threads for reduced rework This insert provides a defined 55° thread profile and a 40–32 TPI pitch for repeatable inspection of Whitworth-form threads. By using a standardised reference, the accessory supports faster go/no‑go decisions on thread quality and reduces costly rework cycles. The compact format and low mass make handling simple during serial checks, improving throughput in the inspection process while maintaining traceable results. Seamless integration into existing gauge and inspection workflows Designed as a metrology accessory, the insert mates with standard thread-checking fixtures and gauge holders to form part of a concise measurement routine. The robust geometry ensures stable contact and consistent readings; this stability lowers measurement scatter and supports clear pass/fail criteria in production lines or measuring benches. Compatibility with Whitworth 55° standards simplifies documentation and quality control procedures. Practical design that supports workshop efficiency With a lightweight construction and clear specification, the insert simplifies storage and deployment across multiple stations. The small form factor allows easy transport between benches without adding handling complexity, while the precise profile reduces operator influence during checks. Together, these aspects contribute to a measurable improvement in inspection speed and reproducibility for routine thread verification. Contact Metav Werkzeuge for tailored advice on integrating the M309.098.2 thread insert into inspection setups or to arrange procurement and delivery from Emmerich. Technical Data Article number: M309.098.2 GTIN: 4054469118338 Label: Gewinde‑Einsätze, 40 - 32 TPI, 55° für Whitworth 55° Manufacturer: Metav IndustryLine Facts Thread pitch: 40 − 32 TPI Angle: 55° Weight: 0.1 kg Tariff number: 90173000 ECLASS: 21170324 Special features Designed for Whitworth 55° thread form Category: Accessory for metrology / gauges Compact, lightweight design Two product images available (main and detail) FAQ What thread form and pitch does this insert represent? The Gewinde‑Einsätze M309.098.2 represents a Whitworth 55° profile with a 40–32 TPI pitch for standardised thread checks. Can this insert be used in production line inspections? Yes. The M309.098.2 thread insert is designed as a metrology accessory for routine checks and can be integrated into production inspection workflows to support quick pass/fail evaluation. Is the insert supplied with calibration documentation? The product data does not specify supplied calibration documents. For details on certification or traceable calibration for the M309.098.2, please contact Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Precision micrometers built for repeatable accuracy
Micrometers—also referred to as micrometer screw gauges or micrometer callipers—are compact, robust instruments for fast, highly accurate length measurement of small to medium workpieces. Designed for routine use on the shop floor, these tools combine mechanical reliability with options for digital data capture, making them indispensable where repeatable tolerances matter.
How micrometers work and where they belong in production
Micrometers operate on a finely threaded spindle that brings two measuring faces into alignment with the workpiece; many designs follow the Abbe comparator principle so that the measuring axis and scale are collinear, reducing tilting errors. Typical outside micrometers (bühlermessschrauben) provide readings down to 1/1000 mm (0.001 mm) in analogue form; internal micrometers and specialised two- or three-point gauges enable accurate diameter and bore measurements, while depth micrometers cover depths from 0–300 mm. Hardened carbide (HM) measuring faces are standard to prevent wear and maintain accuracy over time. Digital variants offer easy reading, unit switching (mm/inch) and data output via USB, RS interface or Bluetooth; advanced models with an integrated minicomputer support Go/NoGo checks, temperature compensation and wireless transmission up to 50 m.
Practical benefits that improve shop‑floor performance
- Reduced rework and higher first-pass yield thanks to repeatable accuracy and carbide-tipped measuring faces.
- Faster, safer measurement cycles by using the ratchet/coupling to limit measuring force to 5 N to 10 N, protecting both part and instrument.
- Flexible inspection workflows with analogue, digital and minicomputer options, including wireless data transfer and mm/inch toggle.
- Versatile coverage with outside, internal, depth and built-in micrometers offering measuring ranges from a few millimetres up to 300 mm and resolution down to 2 µm (internal) or 0.003 mm (standard depth micrometers).
- Durable operation in workshop environments: mechanical models resist dust and moisture, while digital versions are available with IP54 protection.
Metav — a precision partner you can rely on
Metav combines decades of technical expertise with a broad, quality-filtered product range from its Emmerich hub. Over 48,000 customers trust Metav’s offer of more than 250,000 products, which simplifies procurement and secures reliable supply for industry, trade and specialist retailers. For buyers seeking micrometers with consistent performance and traceable data capture, Metav’s selection and technical support make it a practical, long-term choice.
In short
Micrometers provide robust, highly repeatable measurement for external, internal and depth applications, available in analogue, digital and minicomputer formats to match precision requirements and data‑management needs.
FAQ
How precise are micrometers for internal measurements?
Internal micrometers in the micrometers category can achieve accuracies around 2 µm when correctly used; digital and minicomputer models improve readout convenience and data integration for traceable inspection results.
When is a digital micrometer preferable to an analogue one?
Choose a digital micrometer when easy readout, unit conversion (mm/inch), or data transmission is required. Digital models with IP54 rating also offer dust and splash protection, while analogue micrometers remain the most robust option in harsh environments.
What measuring force should be used to ensure consistent results?
The recommended measuring force for micrometers is 5 N to 10 N. Use the ratchet or friction thimble to apply this consistent force and rely on the insulating sleeve to minimise heat transfer from the hand.
Can depth micrometers measure small bores and tight features?
Yes. Depth micrometers use a fine needle or flat measuring face and, with suitable extensions, cover narrow or deep features; standard depth micrometers typically span 0–300 mm with accuracies near 0.003 mm, while specialised digital systems offer even higher resolution.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com