Precision micrometers for reliable dimensional control
Micrometers deliver precise length and depth measurements in metalworking, enabling repeatable control over component tolerances and process stability. These instruments—available as outside micrometers, inside micrometers and depth micrometers—offer hardened contact faces and fine-thread spindles to ensure long-term accuracy and resistance to wear, with digital versions providing data transfer via USB or Bluetooth for seamless integration into inspection software. Typical uses include measuring small bores, depths and diameters in precision engineering, where features must be defined to micrometre-level accuracy; features such as ratchet thimbles and insulated frames help maintain consistent measuring force and temperature compensation. Choose between robust analog models, IP54-protected digital micrometers or micrometers with an integrated minicomputer for advanced functions like unit conversion, temperature correction and Go/NoGo evaluations.
40-50mm Three-Point Bore Micrometer 1.5" Colour Touchscreen, ISO 17025 Calibrated, Wireless/USB - Microtech Metrology
Take advantage of ISO 17025 traceability and a 0.004 mm accuracy together with reliable Wireless + USB data transfer for seamless integration into quality workflows. Order the Three-Point Internal Micrometer directly via Metav Werkzeuge or contact the consultants for an application check. Three-Point Internal Micrometer (40–50 mm) — Wireless + USB, 1.5" Colour Touchscreen (Microtech Metrology) The Three-Point Internal Micrometer is a digital precision instrument for repeatable internal diameter measurement in production control and component inspection. Wireless + USB data output 1.5" colour touchscreen display ISO 17025 calibrated with certificate Measuring range 40–50 mm, depth 240 mm Consistent traceability for quality control This instrument delivers laboratory-grade traceability through its ISO 17025 calibration, supplied with a calibration certificate. The certified adjustment ensures measurement results can be documented and audited, which is essential in production control and incoming inspection. With a stated accuracy of 0.004 mm and a fine display resolution of 0.0001 on the digital readout, the device reduces uncertainty in tolerance-critical checks and supports documented quality systems. Efficient data handling and workshop integration Equipped with Wireless + USB outputs and a 1.5" colour touchscreen, the device accelerates data capture and reduces manual transcription. The digital interface simplifies zeroing, unit switching and data export, enabling direct transfer into inspection software or SPC systems. As a result, inspection cycles shorten and traceable measurement records become standard practice on the shop floor, supporting faster decision making and fewer rejects. Designed for practical measurement tasks The three-point measuring head and 40–50 mm measuring range combine to give a compact yet stable solution for internal diameters, while the 240 mm measuring depth allows access to recessed bores. The included adjustment ring facilitates fine centring and repeatable contact pressure, improving reproducibility across operators. Built as a digital gauge, the instrument is suitable for routine testing, tool setup and sample inspection where reproducible bore measurement is required. Contact Metav Werkzeuge for a specification sheet or application advice on how the Microtech Metrology three-point internal micrometer can be integrated into existing inspection processes — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: 133705010 GTIN: 4061905074264 Manufacturer: Microtech Metrology Facts Measuring range: 40–50 mm Measuring depth: 240 mm Accuracy: 0.004 mm Readout resolution: 0.0001 Display: Colour 1.5" touchscreen Special features Digital instrument Data output: Wireless + USB Adjustment ring: included ISO 17025 calibration and certificate supplied Three-point internal measuring principle FAQ Is this instrument suitable for precision bore measurement in a production environment? The Three-Point Internal Micrometer from Microtech Metrology (SKU 133705010) is designed for production and inspection tasks requiring repeatable internal diameter checks within the 40–50 mm range. Does the device come with traceable calibration documentation? Yes, the micrometer is delivered fully calibrated to ISO 17025 and includes the calibration certificate for audit and traceability purposes. How are measurement results exported from the instrument? Measurement data can be exported via the unit’s Wireless + USB interfaces; this supports direct logging into inspection software or manual data capture workflows. What accuracy and display resolution can be expected during measurements? The instrument specification states an accuracy of 0.004 mm with a readout resolution of 0.0001, suitable for tight-tolerance internal diameter measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
40-50mm Three-Point Inside Micrometer Pistol Grip, Colour Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of high-resolution digital readout, ISO 17025 factory calibration with certificate, and versatile data export (Wireless + USB) for reliable traceability and efficient quality control workflows. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three-point internal micrometer by Microtech Metrology — Wireless + USB, Colour 1.54" touchscreen The Three-point internal micrometer is a compact, digitally driven instrument designed for fast, repeatable internal diameter measurement in precision engineering and quality control. Wireless and USB data output ISO 17025 calibration with certificate 40–50 mm measurement range 0.004 mm accuracy (4 µm) and colour touchscreen Precision for compact internal measurements The gauge is optimised for internal diameters in the 40–50 mm measurement range, classing it among compact instruments suited to fine mechanical work and small-bore quality checks. The three-point contact configuration stabilises the measuring datum and reduces orientation errors during insertion, which improves repeatability for small components. This balance of reach and stiffness supports consistent readings on bearings, bushings and small housings while keeping handling straightforward on the workshop bench. Fast digital capture and traceable results Equipped with a Colour 1.54" touchscreen and a high-resolution readout (0.0001 mm), the instrument enables rapid, unambiguous measurement interpretation and straightforward parameter adjustment. Data export is possible via Wireless connection or USB, allowing direct integration with inspection software and SPC systems for faster batch documentation. Delivered with ISO 17025 calibration and a calibration certificate, the unit supports audit requirements and immediate traceability in production and laboratory processes. Built for low uncertainty and extended reach options The instrument achieves an accuracy of 0.004 mm, offering a level of precision suitable for demanding quality assurance tasks. Two measuring depth options (measuring depths 97 mm and 150 mm) extend the application to deeper bores and recessed features, reducing the need for multiple specialised tools. The digital measurement chain and robust three-point contacting work together to minimise operator influence and maintain measurement integrity across repeated cycles. Practical use and workshop integration Compact and digitally capable, the micrometer integrates into routine inspection routines without complex setup. The combination of digital readout, simple touchscreen operation and direct data transfer speeds up documentation and reduces transcription errors. The calibration status (supplied according to ISO 17025) simplifies incoming inspection and first-article verification, making the instrument a pragmatic choice for small-batch production or laboratory verification where traceability and efficiency are priorities. Contact Metav Werkzeuge for expert procurement advice and to request the ISO 17025 calibration certificate for this Microtech Metrology three-point internal micrometer (SKU 133505010) Technical data Article number: 133505010 GTIN: 4061905041822 Manufacturer: Microtech Metrology Facts Measurement range: 40–50 mm Measuring depths: 97 mm and 150 mm Accuracy: 0.004 mm Resolution (display): 0.0001 mm Display: Colour 1.54" touchscreen Data output: Wireless + USB Calibration: ISO 17025 (certificate included) Special features Digital instrument with touchscreen readout Wireless data transfer and USB interface Supplied calibrated to ISO 17025 with certificate ECLASS: 21170335 ETIM: EC003590 FAQ Is the instrument delivered with a calibration certificate? Yes. The three-point internal micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025, and a calibration certificate is included with the instrument. How is measurement data transferred to a PC or inspection system? Measurement values can be exported via Wireless connection or by USB for direct import into SPC software or inspection databases. What measurement range and depths are covered by this micrometer? The instrument covers a 40–50 mm measurement range and offers measuring depths of 97 mm and 150 mm, suitable for small bores and recessed features. What level of precision can be expected in routine use? The instrument provides an accuracy of 0.004 mm with a high-resolution display (0.0001 mm), designed for repeatable internal diameter checks in quality control. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
40-50mm Three-Point Internal Micrometer Self-Centering, 0.006mm Accuracy, Supplied in Case - Metav IndustryLine
Combine the self-centring three-point contact with a 40–50 mm measuring range and a readability of 0.005 mm to secure consistent internal measurements; delivered in a protective case and available through Metav Werkzeuge for immediate procurement or technical advice. M836.713 three-point internal micrometer — self-centring, 40–50 mm The M836.713 three-point internal micrometer is an analogue inside micrometer designed for accurate bore measurements in quality control and workshop inspection. Self-centring three-point contact Measuring range 40–50 mm Resolution 0.005 mm on vernier Supplied in protective case Reliable precision for internal diameters The three-point contact system provides a consistent datum by aligning all contact points automatically, which reduces operator-induced error and shortens setup time. With an indicated accuracy of ±0.006 mm and a vernier readability of 0.005 mm, the instrument is suited to inspection tasks where repeatability is critical. The analogue design eliminates reliance on electronics, offering a stable, maintenance-light option for standard inspection benches and machine shops. Faster measuring cycles and lower rework Because the device centres itself on the bore, measurement cycles become more efficient and less dependent on manual alignment. The self-centring feature yields reproducible results across multiple operators, cutting down on scrap and rework. Hardened measuring faces resist wear during repeated contact and preserve dimensional integrity over long service intervals, supporting consistent process control in production environments. Robust delivery and workshop compatibility The micrometer arrives in a protective case suitable for safe transport and storage, which helps maintain calibration between uses. The analogue vernier scale is immediately readable to 0.005 mm and requires no batteries, making the tool dependable in harsh or low-power settings. For traceable inspection routines, the instrument’s specifications and serial details are documented, facilitating integration into existing quality records and routine checks. For application-specific guidance or to arrange supply through Metav Werkzeuge, contact our measurement consultants at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and delivery options. Technical data Article number: M836.713 GTIN: 4061905040634 eClass: 21170335 ETIM: EC003590 Data Measuring range: 40–50 mm Resolution (vernier): 0.005 mm Accuracy: ±0.006 mm Display: analogue Special features Self-centring three-point contact Hardened measuring faces Supplied in protective case Category: Analogue inside micrometer FAQ What measurement range does the instrument cover? The instrument measures internal diameters in the 40–50 mm range, suitable for small-bore inspection and component checks. How precise are the readings from this micrometer? Readability is 0.005 mm via the vernier and the stated accuracy is ±0.006 mm, providing reliable repeatability for workshop verification tasks. Is the contact system suitable for quick set‑up on production lines? Yes, the self-centring three-point system speeds alignment and reduces operator variation, making it practical for routine production checks. Does the tool require electronic calibration or batteries? No—this is an analogue instrument with a mechanical vernier; no batteries are needed and field use is straightforward. How is the instrument delivered and protected? The micrometer is supplied in a protective case for transport and storage to help preserve the measuring faces and maintain accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-50mm Three-Point Internal Micrometer Self-Centring, Precision 0.005mm, Supplied in Case - Metav IndustryLine
Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-50mm Three-Point Internal Micrometer With Measurement Drum Scale, IP65 - Metav IndustryLine
Take advantage of the instrument's combination of three-point internal contact, a digital display with ABS/INC/UNIT functions, and workshop-grade IP65 protection for consistent, repeatable inspection of blind-hole bores. Order the unit through Metav Werkzeuge or contact our consultants for tailored technical advice and delivery coordination. Three-point Internal Micrometer M312.238.M — Digital internal micrometer with IP65 protection The Three-point Internal Micrometer M312.238.M is a digital precision instrument designed for reliable measurement of blind-hole diameters in mechanical and mould-making applications, covering the 40–50 mm range. Three-point internal measurement for blind holes Digital display with ON/OFF/SET and ABS/INC/UNIT IP65 protection for workshop environments Accuracy ±0.005 mm, suitable for precision work Consistent centring and high repeatability for blind-hole inspection The three-point contact geometry combined with a measuring drum with scale ensures stable, self-centring engagement in blind holes, reducing eccentricity and operator variance. With a reading and accuracy of 0.005 mm, this instrument delivers the repeatability required for quality control and assembly checks in toolmaking and small-series production. The mechanical design is optimised to convert precise spindle rotation into reproducible radial positioning, which shortens setup times and reduces scrap rates. Workshop-hardy digital handling and clear measurement readout Equipped with a robust digital display (ON/OFF/SET and ABS/INC/UNIT functions) and sealed to IP65, the micrometer withstands coolant spray and dusty environments while keeping measurements readable and reliable. The compact instrument is supplied with a setting ring and an extension (150×Ø23,4) for access to recessed features, so calibration and adaptation to specific bores are straightforward. The solid feel of the instrument supports confident handling during repetitive checks, increasing throughput without sacrificing precision. Integration into inspection routines and normative compliance Classified in the micro measuring range (max. 50 mm), this device is suitable where short jaws and high stiffness are needed—for example, watchmaking, precision components and mould cavities. It is manufactured to DIN 863 standards and offers a clear path to digital workflows via data output RB 4.1 for downstream logging or SPC integration. The combination of a tactile measuring drum and an electronic readout provides both the trusted mechanical feedback inspectors expect and the efficiency of immediate digital capture. Contact Metav Werkzeuge for detailed specification matching, delivery options and expert advice on how the Metav IndustryLine three-point internal micrometer can be integrated into existing inspection procedures — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data SKU: M312.238.M GTIN: 4054469162393 Brand: Metav IndustryLine Facts Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: ±0.005 mm Weight: 2.6 kg Protection class: IP 65 Special features Three-point internal contact for blind holes Measuring drum with scale Digital display with ON/OFF/SET and ABS/INC/UNIT Includes setting ring and extension (150×Ø23,4) Compliant with DIN 863 Data output: RB 4.1 FAQ How accurate is the micrometer for internal diameters? The instrument achieves an accuracy of ±0.005 mm, with a reading of 0.005 mm, making it suitable for high-precision internal diameter checks. Can this device measure blind-hole bores? Yes, the three-point contact design is intended for blind-hole measurement and is supplied with an extension to reach recessed bores. Is the display suitable for harsh workshop conditions? The digital readout is protected to IP65, offering resistance to dust and splashing fluids typically encountered in workshops. Does the micrometer support digital data transfer? The device provides a RB 4.1 data output for connection to data loggers or inspection software, facilitating traceable measurement records. Which standards does the instrument comply with? Manufacture and functional design conform to DIN 863, ensuring compatibility with common workshop and inspection requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-50mm Three-Point Internal Micrometer With Setting Ring And Extension, Calibrated, Supplied In Case - Metav IndustryLine
Take advantage of the combination of high repeatability, a 40–50 mm measuring range and 0.005 mm accuracy for reliable internal measurements of blind holes; order the instrument directly via Metav Werkzeuge or contact the consultants for application advice. Three-point internal micrometer — precise internal measurement, 40–50 mm, 0.005 mm accuracy (Metav IndustryLine) The three-point internal micrometer is a compact precision instrument for measuring internal diameters, designed for blind-hole applications and workshop use. 40–50 mm measuring range 0.005 mm measurement accuracy Matt chrome scale and vernier Delivered with setting ring and extension Precision where centring matters The three-point contact mechanism provides a stable, self-centring measurement that reduces positioning errors and improves repeatability. With a 40–50 mm span and a rated 0.005 mm accuracy, this analogue gauge is suited to demanding inspection tasks where internal geometry must be verified rather than estimated. The instrument’s matt chrome scale and vernier improve legibility under workshop lighting, while robust measuring faces ensure consistent contact geometry. These characteristics translate into fewer rework cycles and clearer quality decisions on the shop floor. Purpose and workshop advantages Classified in the micro-range (max. 10–100 mm), this micrometer covers fine mechanical applications such as small-bore components, precision fixtures and assembly parts. The three-point layout is especially effective for blind-hole measurement, as the expanding anvils locate the bore axis before the final reading is taken. Supplied with a setting ring and extension (150 × Ø16.7), the instrument adapts to stepped or recessed bores without improvised jigs. For production environments that value throughput and traceable checks, the combination of compact reach and high resolution supports faster go/no-go decisions and simplifies in-process control. Handling, robustness and supplier assurance Constructed with a matt-chrome finished scale and vernier, the instrument balances corrosion resistance with visual clarity. The presence of defined measuring faces and a solid build (approximate weight 2.7 kg) gives a reassuring tactile feel during measurement, particularly when handling small internal diameters. Delivered in a protective case, the gauge is ready for transport between inspection benches or machines. As part of the Metav IndustryLine, this tool benefits from the supplier’s commitment to democratising precision: a broad product range, dependable logistics from Emmerich and a reputation for consistent quality across industrial and craft sectors. Discuss application specifics with Metav Werkzeuge to ensure the Metav IndustryLine three-point internal micrometer (M312.138.P) matches production needs and to request a tailored quotation Technical data Article number: M312.138.P GTIN: 4054469158679 Brand: Metav IndustryLine Type: Three-point internal micrometer Analog instrument Core measurements Measuring range: 40–50 mm Resolution / reading increment: 0.005 mm Length: 90 mm Weight: 2.7 kg Extension: 150 × Ø16.7 Setting ring: 40 Special features Suitable for blind-hole bores Matt chrome scale and vernier Measuring faces present Delivered with setting ring and extension Supplied in protective case eCl@ss: 21170335 ETIM: EC003590 Tariff code: 90173000 FAQ What measuring range does the instrument cover? The Metav IndustryLine three-point internal micrometer (M312.138.P) covers the 40–50 mm measuring range. What accuracy can be expected from this analogue gauge? The instrument provides a measurement accuracy of 0.005 mm, suitable for fine internal inspections. Is this micrometer suitable for blind-hole measurements? Yes — the three expanding anvils and the instrument design are specifically intended for reliable blind-hole measurement. Which accessories are included with delivery? Delivery includes a setting ring and the extension (150 × Ø16.7) and the tool is supplied in a protective case. How is the scale finished and what is the instrument’s weight? The scale and vernier are matt chrome plated for durability and legibility; the instrument weighs approximately 2.7 kg. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40-90mm Universal Micrometer With Interchangeable Anvils, Wireless+USB Digital Readout - Microtech Metrology
The combination of compact design, high-resolution digital readout and versatile data connectivity makes this micrometre an efficient choice for precision inspection and small-part assembly. With a measuring range suited to micro applications and an accuracy of ±0.004 mm, reliability is balanced with easy data capture. Order the micrometre directly via Metav Werkzeuge or ask our consultants if needed. Universal outside micrometre — digital with Wireless + USB (Microtech Metrology) Universal outside micrometre for precise external measurements in fine mechanical and inspection tasks, covering the micro measuring range from 40 to 90 mm. Digital display 0.0001 mm resolution Wireless and USB data output Accuracy ±0.004 mm Interchangeable anvils not included Precision for micro applications and traceable measurement The micrometre is designed for the micro range (max 10–100 mm), making it ideal for fine mechanical work where compact dimensions and repeatability matter. The instrument delivers a resolution of 0.0001 mm and an accuracy of ±0.004 mm, values that support routine quality checks and dimensional control in workshops and small-series production. The combination of a high-resolution digital readout and robust mechanical guidance reduces reading errors and speeds up inspection cycles, which improves throughput without sacrificing measurement certainty. Integration into measurement workflows and data capture Equipped with Wireless and USB data outputs, the device enables straightforward transfer of readings into SPC systems or inspection software, cutting manual transcription and potential input errors. The digital interface supports efficient documentation and faster traceability during batch inspections. The instrument’s measuring depth of 32 mm and compact frame suit confined setups and jig-mounted checks; interchangeable anvils are supported for application flexibility, but anvils are not included, allowing configuration for specific tasks as required. Robust handling and everyday benefits at the bench Built for frequent use, this digital micrometre combines practical ergonomics with direct data export to simplify quality routines. The compact instrument is well suited to precision assembly, small components and laboratory inspection where a balance of repeatability, data connectivity and quick handling is required. Integration-friendly interfaces mean fewer process interruptions and a more reliable audit trail for measurement results, enhancing both productivity and compliance in the workshop. Discuss data-integration options and order the Microtech Metrology micrometre via Metav Werkzeuge to equip the workshop with a compact, connected measuring solution; Metav Werkzeuge in Emmerich provides technical advice and local supply. Technical Data Article number: 115050977 GTIN: 4061905458231 Manufacturer: Microtech Metrology Facts Measuring range: 40–90 mm Measuring depth: 32 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Data output: Wireless + USB Digital device: yes Special features Interchangeable anvils (not included) Compact frame for micro-range measurements Suitable for fine mechanical and inspection work FAQ What measuring range does this micrometre cover? The Universal outside micrometre covers 40–90 mm, placing it in the micro-range category suited to fine mechanical parts and small assemblies. Is the micrometre ready for data transfer to inspection software? Yes, the instrument offers Wireless and USB data outputs for straightforward connection to SPC systems and measurement software. Are interchangeable anvils supplied with the micrometre? Interchangeable anvils are supported for the Microtech Metrology micrometre, but the anvils are not included with the device and must be ordered separately if required. What accuracy and resolution can be expected during routine use? The device provides a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for precise quality-control tasks in workshops and small-series production. For which applications is this micrometre best suited? This compact digital micrometre is intended for fine mechanical inspection, small-part assembly and laboratory checks where compactness, repeatability and data capture are priorities. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
400-450mm Bore Gauge Micrometer With Microcomputer, Wireless/USB, Ø8mm Measuring Faces, ISO 17025 Calibrated - Microtech Metrology
Take advantage of ISO 17025 traceability, reliable 0.01 mm resolution and wireless data transfer to speed up inspection routines; order the calibrated instrument directly via Metav Werkzeuge or ask their consultants for application advice. Outside Micrometer 400–450 mm — digital, Wireless + USB (Microtech Metrology) The Outside Micrometer 400–450 mm is a digital precision instrument for measuring large external diameters in production and inspection environments. ISO 17025 calibration certificate included Wireless and USB data output 0.01 mm resolution for precise measurement Ø8 mm hardened measuring faces Robust measurement for large diameters The micrometer covers a measuring range 400–450 mm, providing a dependable solution for external diameter checks on sizeable components such as shafts, large bearings and housings. The long spindle travel is supported by a measuring depth 110 mm, which maintains consistent contact geometry even on deep or recessed features. Hardened Ø8 mm measuring faces ensure wear resistance and repeatability over many cycles, reducing the need for frequent readjustment and extending service intervals on the shop floor. Traceable accuracy and seamless data capture A digital readout with 0.01 mm resolution gives clear, comparable readings for routine quality control. The instrument is delivered fully calibrated to ISO 17025, including a calibration certificate that supports audit trails and measurement traceability. Integrated Wireless and USB outputs enable error‑free transfer of measured values into statistical process control (SPC) systems or inspection software, eliminating manual transcription and speeding up documentation workflows for production monitoring and reporting. Durable design and straightforward operation Microcomputer control and a clear digital display simplify handling of a large-format measuring instrument, while precision mechanisms maintain stability during repeated measurements. The combination of a rigid frame and hardened anvils provides both stiffness and surface protection, so the device remains accurate under frequent use. The ergonomic control elements and rapid data output reduce cycle time in batch inspections and make the device suitable for busy metrology benches or on‑line quality stations. Fits into professional quality management processes The instrument is designed to integrate with laboratory procedures and workshop routines alike. With ISO 17025 calibration included and standardised data interfaces, the micrometer supports documented measurement procedures and helps to align everyday inspections with formal quality systems. Its specification is aimed at engineers and technicians who require both reproducible results and straightforward digital data handling for traceable measurement records. For traceable measurements and seamless data capture, contact Metav Werkzeuge in Emmerich (info@metav-werkzeuge.com, +49 2822 7131930) to discuss the Microtech Metrology calibrated outside micrometer (SKU 115054507) and suitable integration options Technical Data Article number: 115054507 GTIN: 4061905040962 Manufacturer: Microtech Metrology Data Measuring range: 400–450 mm Resolution: 0.01 mm Measuring depth: 110 mm Measuring faces diameter: Ø8 mm Special features Digital display with microcomputer control Data output: Wireless + USB Delivered calibrated to ISO 17025 with certificate Suitable for external diameter measurement Category: Outside micrometer FAQ What measuring range does the instrument cover? The Microtech Metrology outside micrometer (SKU 115054507) covers a measuring range of 400–450 mm for large external diameters. Is the instrument supplied calibrated? Yes. The micrometer is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. How can measurement data be transferred to a PC or SPC system? Data transfer is available via Wireless and USB outputs to integrate measurements directly into inspection software or SPC systems. What is the resolution and typical use case for this micrometer? Resolution is 0.01 mm, making the instrument suitable for routine industrial quality control of large components where consistent, reproducible readings are required. What are the measuring faces made for? The measuring faces are Ø8 mm hardened anvils designed to resist wear and to preserve measurement accuracy over prolonged use. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
400-450mm Digital Universal-Bügelmessschraube mit auswechselbaren Ambossen, Mikrocomputer, Wireless+USB, 0,01mm Ablesung, Ambosse NICHT inklusive - Microtech Metrology
Die Universal-Bügelmessschraube von Microtech Metrology kombiniert Genauigkeit von 0,01 mm mit flexibler Datenausgabe per Wireless und USB sowie einem robusten Messbereich von 400–450 mm, wodurch Messabläufe in Fertigung und Qualitätssicherung effizienter werden. Für komplette Versorgung und sichere Lieferung steht Metav als erfahrener Präzisions-Partner bereit; bei Bedarf technische Beratung anfordern. Universal-Bügelmessschraube von Microtech Metrology Die Universal-Bügelmessschraube ist ein digitales Messgerät für präzise Außenmessungen in Industrie und Werkstatt Präzision 0,01 mm für exakte Messwerte Messbereich 400–450 mm für größere Bauteile Datenausgang Wireless und USB Messtiefe 110 mm für tiefere Messungen Ambosse nicht inklusive, auswechselbare Aufnahme Präzision und verlässliche Datenübertragung für den Produktionsalltag Die Universal-Bügelmessschraube bietet eine nachweisbare Genauigkeit von 0,01 mm und ist damit für qualitätskritische Messaufgaben ausgelegt. Die digitale Anzeige in Verbindung mit dem integrierten Mikrocomputer sorgt für eine stabile Messwertverarbeitung, während der Datenausgang per Wireless und USB die direkte Einbindung in Prüfprotokolle und Fertigungsdatensysteme erlaubt. Dieser Aufbau reduziert Fehlerquellen bei der Datenerfassung und beschleunigt Messvorgänge in Serie. Großer Messbereich und praktische Messtiefe für vielseitige Anwendungen Der Messbereich von 400–450 mm und die Messtiefe von 110 mm ermöglichen das Messen von größeren Werkstücken, die sonst gesonderte Vorrichtungen erfordern würden. Die Bauform als Bügelmessschraube garantiert dabei eine einfache Handhabung bei Außenmessungen, während die auswechselbare Ambossaufnahme Flexibilität bei speziellen Messaufgaben bietet. Hinweis: Ambosse sind nicht inklusive und müssen passend zur Anwendung separat beschafft werden. Einfache Integration und Bedienung im Prüfablauf Die digitale Ausführung mit Mikrocomputer erleichtert das Kalibrieren und Übertragen von Messdaten in vorhandene Systeme. Wireless steht für kabellose Übertragung, USB für kabelgebundene Schnittstellen und Datensicherung. So lassen sich Messergebnisse schnell dokumentieren und in Qualitätssicherungsprozesse einspeisen. Wartung und Bedienung sind praxisgerecht gestaltet, wodurch sich Stillstandszeiten minimieren und die Messzyklen effizienter organisiert lassen. Zielgruppenorientierte Eignung für Industrie und Werkzeugbau Dieses Messgerät richtet sich an Qualitätssicherung, Werkzeugbau und industrielle Fertigung, die präzise Außendurchmesser über längere Messbereiche erfassen müssen. Anwender profitieren besonders bei Serienprüfungen und dokumentationspflichtigen Messabläufen, weil die Kombination aus hoher Genauigkeit und direkter Datenübertragung Routineaufgaben vereinfacht. Metav liefert dabei nicht nur das Produkt, sondern auch Beratung und zuverlässige Versorgung aus Emmerich. Microtech Metrology Präzision für Ihren Betrieb sichern und Metav für technische Beratung kontaktieren: E‑Mail info@metav-werkzeuge.com Telefon +49 2822 7131930 WhatsApp +49 170 2837271 Produktmerkmale Artikelnummer: 115054577 Marke: Microtech Metrology Bezeichnung: Universal-Bügelmessschraube mit auswechselbaren Ambossen und Mikrocomputer GTIN: 4061905457937 Daten Messbereich: 400–450 mm Genauigkeit: 0,01 mm Messtiefe: 110 mm Besonderheiten Datenausgang: Wireless (kabellose Übertragung) und USB (kabelgebundene Schnittstelle) Digital: Ja Ambosse: Nicht inklusive ECLASS: 21170328 FAQ Welche Genauigkeit bietet die Universal-Bügelmessschraube? Die Universal-Bügelmessschraube von Microtech Metrology zeichnet sich durch eine Genauigkeit von 0,01 mm aus, was sie für präzise Prüfaufgaben in Labor und Fertigung geeignet macht. Sind Ambosse im Lieferumfang enthalten? Ambosse sind nicht inklusive; die Universal-Bügelmessschraube verfügt über eine auswechselbare Ambossaufnahme, sodass passende Ambosse separat beschafft werden können. Wie werden Messdaten übertragen und gespeichert? Die Universal-Bügelmessschraube unterstützt Wireless und USB als Datenausgang, wodurch Messergebnisse direkt an Prüfsoftware oder Datenerfassungssysteme übermittelt werden können. Für welche Anwendungen ist das Messgerät besonders geeignet? Das Messgerät eignet sich für Außenmessungen an größeren Bauteilen, Serienprüfungen und Qualitätssicherungsprozesse, insbesondere im Werkzeugbau und in der industriellen Fertigung.
400-500mm Bore Micrometer Digital Touchscreen, ISO 17025 Calibrated, Ø25mm Measuring Faces - Microtech Metrology
Benefit from sub-micron reliability, wireless DataMet connectivity and a rigid CNC‑machined aluminium housing for consistent measurements across medium‑sized assemblies; the instrument is supplied with an ISO 17025 calibration certificate. Order the micrometer directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology DataMet outside micrometer 400–500 mm — colour touchscreen & wireless output The Microtech Metrology DataMet outside micrometer is an industrial digital micrometer designed for accurate external measurement of medium‑sized components in fixtures, moulds and assembly work. Sub-micron accuracy ±0.005 mm Wireless DataMet synchronisation ISO 17025 calibration certificate included CNC-machined aluminium housing Reduce rejects with measurable precision This outside micrometer delivers an industrial accuracy of ±0.005 mm, which supports tighter process control and fewer reworks when checking critical external dimensions. The instrument’s robust measuring faces (Ø25 mm) and a solid, CNC‑machined aluminium housing maintain stability during repeated measurements, so readings remain consistent across production shifts. The combination of mechanical rigidity and fine tolerance contributes directly to lower scrap rates and improved first‑pass yield. Capture and manage measurement data without interruption Equipped with a Colour 1.5" touchscreen and a comprehensive memory manager (up to 2,000 values), the device stores measured results and basic statistics locally. Data transfer modes include Wireless+USB and wireless HID options, enabling quick synchronisation with inspection software or a shop‑floor tablet; an optional MODBUS RTU output is available for direct integration into industrial PLC networks. These features streamline quality documentation and support Industry 4.0 workflows by removing manual logging steps. Designed for workshop handling and repeatability With a measuring range of 400–500 mm, the micrometer fits the “Mittel” category—suitable for larger jigs, housings and machine components where reach and stiffness must be balanced. The instrument’s weight (2.2 kg) and ergonomics are optimised for stable, repeatable hand measurements, while the colour touchscreen simplifies mode selection and on‑screen prompts. Built‑in functions such as Max/Min, Go/No‑Go and linear/temperature correction increase measurement relevance without extra tools. Traceable calibration and industrial compatibility The micrometer is delivered with a full calibration certificate performed to ISO 17025 (Ilac MRA), providing documented traceability for audits and supplier assessments. Paired with the DataMet measuring hub and Microtech’s MICS system, the device offers online graphical display, probe modes and compensation options that assist technicians in diagnosing process drift. This traceability and connectivity combine to reassure customers and auditors about measurement integrity. Contact Metav Werkzeuge for technical integration advice, the ISO 17025 calibration certificate and details on connecting the Microtech Metrology micrometer to existing data collection systems Technical data Article number: 110185008 GTIN: 4061905039577 Manufacturer: Microtech Metrology SKU: 110185008 Facts Measuring range: 400–500 mm Accuracy: ±0.005 mm Measuring faces: Ø25 mm Display: Colour 1.5" touchscreen Weight: 2.2 kg Special features Wireless+USB data output Memory manager: 2,000 values DataMet measuring hub compatibility Optional MODBUS RTU (RS‑485) CNC‑machined aluminium housing Calibration certificate: ISO 17025 (Ilac MRA) included Functions: Go/No‑Go, Max/Min, linear and temperature correction, statistics FAQ Is the instrument delivered calibrated? Yes. The Microtech Metrology DataMet outside micrometer is supplied with a full calibration certificate performed to ISO 17025 (Ilac MRA). Which measuring range does this micrometer cover and what workshop class is it? The micrometer covers 400–500 mm and falls into the Mittel class, offering the reach required for larger fixtures and assemblies while remaining manageable for hand measurement. How are measurement results exported from the device? Measurement data can be exported via Wireless+USB modes, wireless HID options and can be synchronised with the DataMet hub; optional MODBUS RTU is available for PLC connections. What level of traceability and documentation is provided for audits? Traceability is ensured by the included ISO 17025 calibration certificate; the micrometer also records statistical values and stores up to 2,000 measurements for audit trails. Can the micrometer integrate with Industry 4.0 systems? Yes. The DataMet features, wireless synchronisation and optional MODBUS RTU permit integration into modern data acquisition and PLC systems for centralised process monitoring. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
400-500mm Micrometer With Digital IP65 Display, Friction Ratchet, Ø25mm Measuring Faces, ISO 17025 Calibrated - Microtech Metrology
Take advantage of a rugged, workshop-ready measuring instrument that combines a wide 400–500 mm measuring range, an IP65-protected digital head and a traceable ISO 17025 calibration certificate for immediate use in quality control. Order the micrometer directly via Metav Werkzeuge or consult the team for application advice. Microtech Digital Outside Micrometer 400–500 mm — digital, IP65, ISO 17025 calibrated A Microtech Digital Outside Micrometer 400–500 mm designed for robust, repeatable external measurements of large components in production, toolmaking and inspection environments IP65-protected digital head ISO 17025 calibration certificate included Measuring range 400–500 mm Ø25 mm hardened measuring faces Precision where large-format measurement matters The large-frame digital micrometer delivers repeatable measurements across a substantial span thanks to a robust frame and Ø25 mm measuring faces that distribute contact forces. The instrument features a digital display with a fine 0.001 mm reading and an indicated accuracy of ±0.007 mm, which together reduce reading errors and support tighter tolerance verification in production. Included setting rods and a delivered calibration certificate under ISO 17025 ensure immediate traceability and documentation for quality assurance processes. The combination of high resolution and certified calibration makes the micrometer suitable for final inspection of assemblies where reliable dimensional data is essential. Built for workshop use: durability and consistent handling Designed for repetitive measuring tasks, the unit offers a friction ratchet to standardise closing force, minimising variation caused by different operators. The IP65 protection rating means the measuring head is sealed against dust and low-pressure water jets, supporting use at the workbench or on the shop floor without sacrificing the electronics. At approximately 2.2 kg the instrument is substantial enough to feel stable in the hand, which assists in consistent positioning across a long measuring span. These mechanical and protective features translate into fewer out-of-tolerance calls and less rework over time. Traceability, documentation and procurement benefits Delivery includes a full calibration certificate performed to ISO 17025 (Ilac MRA), offering documented measurement credibility for internal audits and customer reporting. The micrometer’s technical specification and supplied documentation simplify integration into inspection routines and metrology records. For purchasing and supply reliability, Metav Werkzeuge acts as a quality filter for the European market, providing access to certified measuring instruments and the option to request additional technical data or advice from a dedicated team. Contact Metav Werkzeuge to request the Microtech digital outside micrometer specification sheet, confirm stock availability at Emmerich and arrange purchase or technical clarification through Metav Werkzeuge. Technical data Article number: 110175001 GTIN: 4061905040115 Manufacturer: Microtech Metrology Digital: yes IP rating: IP65 Facts Measuring range: 400–500 mm Resolution (display): 0.001 mm Accuracy: ±0.007 mm Measuring face diameter: Ø25 mm Weight: 2.2 kg Special features Digital micrometer head with IP65 protection Friction ratchet for consistent measuring force Setting rods included Calibration certificate included (ISO 17025 (Ilac MRA)) Robust frame for large-format external measurement FAQ What measuring range does the micrometer cover? The micrometer covers a 400–500 mm span, suitable for medium-range external measurements of larger components. Is the micrometer supplied with traceable calibration? Yes, the instrument is delivered with a calibration certificate performed to ISO 17025, ensuring traceability and audit-ready documentation. What resolution and accuracy can be expected from the device? The digital display shows 0.001 mm increments and the stated accuracy is ±0.007 mm, providing fine resolution for quality control tasks. Can the micrometer be used on a shop floor environment? With an IP65-protected head and a robust frame, the micrometer is designed to withstand dusty and splashing conditions common in workshop settings. Which accessories are delivered with the micrometer? The micrometer is supplied with setting rods and the stated calibration certificate to enable immediate, documented use in inspection processes. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
4000-5000mm Sub-Micron Modular Bench Micrometer Colour Touchscreen, IP65, ISO 17025 - Microtech Metrology
Take advantage of a modular system that combines long-range measurement capability, robust industrial protection and integrated data handling for uninterrupted production control. The result is a high-capacity, traceable measuring solution that arrives fully calibrated to ISO17025 standards; order directly via Metav Werkzeuge or consult our specialists for configuration and delivery. Microtech DataMet modular outside micrometer — modular system with colour touchscreen The Microtech DataMet modular outside micrometer is a modular, long-range measuring instrument designed for large components and shopfloor integration in industrial metrology. Modular construction for long measuring ranges ISO17025 calibration certificate included Wireless and USB data transfer IP65 protection for industrial environments Built for large-scale precision and repeatability The modular architecture delivers a scalable measuring range of 4000–5000 mm, classifying the instrument among extra-long measurement systems for large components such as shafts, housings and large tooling fixtures. The modular frame and large Ø50 mm measuring faces ensure contact stability and repeatable results over extended spans, while the CNC-machined aluminium housing keeps alignment consistent. Measured values are governed by the system’s stated accuracy of 0.075 mm, which is complemented by the instrument’s industrial rigidity and its substantial mass that reduces the influence of external disturbances. Seamless data flow and Industry 4.0 compatibility Data handling is a core strength: the unit features a colour 1.5" touchscreen, a memory manager for 2000 values with folder organisation, and multiple wireless transfer modes (including Wireless to MDS app and Wireless HID) plus USB HID output. Optional MODBUS RTU (RS‑485) provides direct integration into PLCs and factory networks for automated logging and process control. These capabilities position the micrometer as a rational choice for production environments that require efficient, auditable data streams and reduced manual transcription. Practical operation and measured workflows The instrument’s MICS software supports functions such as on-line graphics, go/no-go checks, max/min capture, formula inputs and temperature compensation, enabling direct decision-making at the measurement point. The modular design allows shipment and reassembly with ease: modules connect to extend the range while preserving calibration parameters. A robust memory and statistics mode simplify quality checks and accelerate traceability tasks, reducing downtime and improving throughput for repetitive inspection routines. Industrial robustness and traceable calibration With an IP65 rating and a solid, CNC-machined block housing, the system withstands harsh shopfloor conditions and routine handling without sacrificing measurement integrity. The micrometer is supplied with a full calibration certificate issued to ISO17025 (Ilac MRA), guaranteeing traceability and compliance for quality assurance procedures. This formal calibration is included with delivery and supports acceptance in regulated manufacturing processes and internal quality audits. Versatile applications and material handling Designed for metrology departments, fixture builders and heavy-duty machining environments, the modular setup addresses large-format measurement tasks that would otherwise require multiple instruments. The instrument’s large measuring faces and module-based reach make it suitable for inspecting assemblies, large shafts and fixtures where conventional hand micrometers cannot reach. Its wireless hub and probe-mode features facilitate synchronised measurements from multiple sensing heads when required. Contact Metav Werkzeuge today to discuss a tailored Microtech DataMet configuration from Emmerich, secure delivery options and assistance with integration into existing measurement workflows Technical data Article number: 110160505 GTIN: 4061905040139 Manufacturer: Microtech Metrology Facts Measuring range: 4000–5000 mm Accuracy: 0.075 mm Weight: 60 kg Modules: 5 Protection class: IP 65 Special features Digital display: Colour 1.5" Touchscreen Data output: Wireless + USB; optional MODBUS RTU Housing: CNC machined aluminium Memory: 2000 values, folder system, statistics mode Measuring faces: Ø50 mm Calibration: ISO17025 certificate included FAQ What measuring range does this system cover? The modular system covers a measuring range of 4000–5000 mm and is intended for extra-long measurements of large components. Is the instrument delivered calibrated for traceability? Yes. The Microtech DataMet modular outside micrometer is supplied with a calibration certificate issued to ISO17025 (Ilac MRA). How are measurements transferred to evaluation software? Measurements can be exported via Wireless to the MDS app, Wireless HID, USB HID, or, optionally, via MODBUS RTU (RS‑485) for PLC and factory network integration. What protection does the unit offer against dust and liquids? The instrument has an IP65 protection rating, suitable for demanding industrial environments. Can the system store a large number of measurements locally? Yes. The built-in memory manager stores up to 2000 values with folder organisation and statistics functions for batch handling. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
400mm Extension Ø22 for Rod Internal Micrometer Sets - Metav IndustryLine
Extend measuring capability with the 400 mm, Ø 22 mm extension rod for reliable deep-bore checks; stable connection and compact handling speed up inspection workflows. Order directly via Metav Werkzeuge or consult our specialists for application advice. Extension rod 400 mm, Ø22 mm for 310.062/310.063 — Metav IndustryLine accessory with extended reach The Extension rod 400 mm, Ø22 mm for 310.062/310.063 is an accessory designed to extend the measuring range of compatible internal measuring sets for deep bores and recessed features in production and inspection environments 400 mm length for extended measuring reach Ø 22 mm shank for stable connection Compatible with 310.062 and 310.063 sets Reach deeper features without additional setups The 400 mm length provides a practical solution when components require measurement beyond the standard instrument span, reducing the need to reposition workpieces or swap to specialised tools. As an extension rod, it is intended to integrate with existing internal measuring sets and thereby maintain workflow efficiency. The modest mass of 0.8 kg allows easier handling during repeated checks while limiting additional inertia that can affect repeatability. Secure interface for repeatable readings A Ø 22 mm shank delivers a consistent mechanical interface with the intended internal measuring sets, ensuring a secure fit and minimising play at the connection point. The design focuses on maintaining measurement stability over the extended length so that results remain comparable to those obtained at shorter ranges. Compatibility with 310.062 and 310.063 means the accessory can be adopted quickly in inspection routines where these sets are already in use. Seamless workshop integration and productivity gains Presented as a straightforward accessory, the rod simplifies the measurement of deep or recessed bores without the procurement of complete additional gauge sets. The extension supports faster inspection cycles and contributes to lower setup times in series checks or on the shop floor. Its specification and SKU (M310.063.5) make ordering, inventorying and traceability uncomplicated within existing metrology systems. For precision extensions and application guidance for Metav IndustryLine accessories, contact Metav Werkzeuge for expert advice and compatibility confirmation — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M310.063.5 GTIN: 4054469118994 Tariff number: 90173000 Weight: 0.8 kg Length: 400 mm Diameter: 22 mm Facts ECLASS: 21019104 ETIM: EC002219 Special features Accessory for internal measuring sets Compatible with models 310.062 and 310.063 SKU: M310.063.5 FAQ Is the extension rod compatible with standard internal micrometer sets? The extension rod is designed to be compatible with the internal measuring sets 310.062 and 310.063; compatibility with other systems should be verified against the Ø 22 mm shank and the connection method. How does the 400 mm extension affect measurement repeatability? When used with the matching internal set, the 400 mm extension maintains repeatability by providing a secure mechanical interface and avoiding the need for multiple repositionings during inspection. What is the item number for ordering and stock identification? The SKU for this extension rod is M310.063.5 and the GTIN is 4054469118994 for ordering and inventory purposes. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
400mm Setting Gauge Metric 60 - Microtech Metrology
Benefit from a Metric 60 thread reference and a 400 mm calibration length that support reliable setup and consistent results; order the setting gauge directly via Metav Werkzeuge or consult our specialists for application advice. Setting Gauge — Thread reference, 400 mm, Metric 60 (Microtech Metrology) A Setting Gauge designed for use as a metric-60 thread reference and calibration aid in workshop and metrology environments. Metric 60 thread reference 400 mm calibration length Accessory for workshop metrology Microtech Metrology quality Precise thread referencing for repeatable setups The setting gauge serves as a dedicated thread reference for applications that require reproducible set-ups or comparative checks. With its Metric 60 designation it provides a clearly defined reference condition for thread-related adjustment tasks, reducing setup time and uncertainty. Engineers and technicians benefit from a consistent datum that simplifies alignment and minimises the trial-and-error phase during fixture or gauge adjustment. Suitable format for extended calibration tasks At a 400 mm length this reference bar bridges the gap between compact gauges and larger calibration standards, allowing measurement benches and fixtures to be checked over a useful span without unnecessary handling complexity. The elongated format supports applications in workshop metrology where a longer reference is necessary, while remaining manageable for bench-top use. The result is improved process efficiency through fewer rework cycles and faster verification steps. Integrates with quality and traceability workflows Intended as an accessory for measurement and setup, the reference bar integrates cleanly into documented quality processes. Use of a dedicated thread reference improves repeatability and supports traceable procedures when recording setup conditions for batch production or inspection runs. Where formal documentation is required, the accessory serves as a stable reference that helps standardise procedures across shifts and workstations. Contact Metav Werkzeuge today for tailored advice on integrating this Microtech Metrology setting gauge into existing measurement processes and to request any supplementary technical data Technical data Article number: 110710040 GTIN: 4061905459290 Manufacturer: Microtech Metrology Facts Length: 400 mm SKU: 110710040 Special features Metric 60 Category: Accessory (Measurement) FAQ What is the primary use of this setting gauge? The setting gauge is used as a Metric 60 thread reference to support calibration, setup and comparative checks in workshop metrology and fixture adjustment. Can the setting gauge be used for traceable setup procedures? Yes, the Microtech Metrology setting gauge is intended to improve repeatability and can be incorporated into documented setup and inspection procedures. What identifiers are available for ordering or inventory? The product is supplied with SKU 110710040 and GTIN 4061905459290 for clear identification. Is this reference suitable for bench-top and fixture checks? The 400 mm length makes the reference bar suitable for bench-top calibration and for checking longer fixtures where a compact gauge would be insufficient. Which brand manufactures this reference gauge? This setting gauge is supplied by Microtech Metrology and marketed as an accessory for workshop metrology. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
400mm Setting Gauge Whitworth 55 - Microtech Metrology
Take advantage of a durable, purpose-built gauge that combines Whitworth 55 compatibility with a 400 mm working length to streamline thread setup and inspection. For reliable integration into workshop metrology routines, order the instrument via Metav Werkzeuge or consult the specialists for application guidance. Thread setting gauge (Einstellmaß) — Whitworth 55, 400 mm by Microtech Metrology Thread setting gauge (Einstellmaß) for Whitworth 55 applications, intended as an accessory for metrology workstations and inspection routines. Whitworth 55 thread compatibility 400 mm working length for extended reach Accessory for measuring instruments Reduce setup time with a dedicated thread reference A dedicated thread setting gauge designed for the Whitworth 55 thread form provides a straightforward reference during machine setup and quality checks. The defined thread profile removes ambiguity when aligning gauges or checking tooling, helping to reduce trial-and-error adjustments. The 400 mm working length offers extended access to larger assemblies and fixtures, so alignment and verification can be completed with fewer repositionings, contributing to faster process cycles and higher workshop throughput. Integrate seamlessly into metrology routines As an accessory for inspection benches and workshop measuring equipment, the instrument supports consistent measurement workflows. The clear specification for Whitworth 55 compatibility makes the part immediately applicable where this thread standard is required, allowing it to function as a repeatable reference during set-up and verification steps. Recorded use of a single, dedicated reference item simplifies procedures and increases repeatability across shifts, which benefits traceable quality assurance in production environments. Procurement and stock management made practical Identification data such as SKU 110720040 and GTIN 4061905460104 facilitate ordering, inventory control and document archiving. The concise item description — accessory for measuring devices with Whitworth 55 thread profile and 400 mm length — supports clear purchasing specifications and avoids ambiguity when sourcing replacements or matching tooling across supplier lists. This clarity reduces administrative friction and helps maintain uninterrupted production. For precise thread set-up and to source the Microtech Metrology thread setting gauge, contact Metav Werkzeuge for ordering and technical advice — Metav Werkzeuge is available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 110720040 GTIN: 4061905460104 Manufacturer: Microtech Metrology Length: 400 mm Special feature: Whitworth 55 Category: Measuring instruments — Accessory Facts Length: 400 mm Special features Whitworth 55 thread compatibility Accessory for metrology and inspection workflows Image asset available for identification FAQ What thread form does this gauge support? The setting gauge is specified for the Whitworth 55 thread form and serves as a reference for that standard. What is the usable length of the instrument? The working length is 400 mm, suitable for extended reach on larger assemblies. How is the item identified for procurement? Identification is provided by SKU 110720040 and GTIN 4061905460104, which can be used for ordering and inventory purposes. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
400‑500mm Digital Bore Gauge With Carbide Measuring Faces, Ratchet Feed, Plastic Case - Metav IndustryLine
Benefit from the combination of 1 µm digital resolution, carbide measuring faces and a ratcheted spindle for reproducible, high‑throughput inspection; order the digital outside micrometer M302.027.C directly via Metav Werkzeuge or consult our specialists if required. Digital outside micrometer M302.027.C — 400–500 mm, 1 µm resolution (Metav IndustryLine) The Digital outside micrometer M302.027.C is a large‑range external measuring instrument designed for accurate dimension control of jigs, fixtures and sizeable machined components. 1 µm digital resolution display Carbide measuring faces for wear resistance Ratcheted spindle for constant measuring force RB 4.1 data output for digital logging Reliability for larger parts and repeatable precision This instrument is tailored for mid‑range inspection tasks where reach and stiffness must be balanced. With a measuring range of 400–500 mm it falls into the medium category of workshop micrometers, offering the reach required for larger assemblies while remaining manageable for single‑operator checks. The 0.001 mm display resolution provides submicron readability and, together with a stated accuracy of 0.013 mm, delivers the reproducible results needed for routine quality control in toolmaking and mould construction. The carbide measuring faces resist wear during repeated contact with hard materials and extend the service life of the tool. Consistent measuring force and ergonomic handling A ratcheted spindle and a spindle pitch of 0.5 mm ensure consistent contact pressure and minimise operator‑induced variance during measurement. The matt‑chromed measuring drum improves legibility while resisting glare in brightly lit inspection areas. The instrument’s digital unit features ON/OFF/SET, ABS/INC and UNIT buttons for straightforward operation and fast changeover between metric and imperial readouts. Physical design choices focus on steady support and an intuitive measuring routine, which speeds throughput and reduces rework in production environments. Digital integration and workshop readiness Data export via RB 4.1 enables straightforward logging into inspection software or SPC systems, supporting traceable measurement records and batch documentation. The device is supplied complete with a protective transport case to safeguard accuracy during handling and transit, and it is built to the manufacturer’s Werksnorm for consistent production standards. Applications include incoming inspection, in‑process verification and final part checks across steel, aluminium and other common workshop materials — the micrometer bridges hands‑on measurement with digital workflows for efficient quality assurance. Contact Metav Werkzeuge today to discuss specification details or to reserve the Metav IndustryLine digital outside micrometer M302.027.C with RB 4.1 output and protective transport case. Technical data Article number: M302.027.C GTIN: 4054469163000 Data output: RB 4.1 Category: Outside micrometer (digital) Core specifications Measuring range: 400–500 mm Resolution: 0.001 mm (1 µm) Accuracy: 0.013 mm Spindle pitch: 0.5 mm Number of measuring spindles: 8 Special features Carbide measuring faces Ratcheted spindle for constant measuring force Measuring drum matt chrome‑plated Digital display with ON/OFF/SET, ABS/INC and UNIT buttons Protective transport case included Built to Werksnorm FAQ What range of dimensions can be measured with this instrument? The digital outside micrometer M302.027.C measures externally from 400 mm to 500 mm, classifying it as a medium‑range instrument suitable for larger workshop components. What level of resolution and accuracy does the micrometer provide? The device offers a 0.001 mm (1 µm) resolution and a specified accuracy of 0.013 mm, which supports reproducible measurements for routine quality control. Are the measuring faces suitable for hard materials? Yes, the micrometer is equipped with carbide measuring faces, providing high wear resistance for frequent contact with hard materials. How is measurement data exported from the unit? Measurement values can be transmitted via the RB 4.1 data output, allowing integration with inspection software and data logging systems. Does the instrument include any protective packaging for transport? The M302.027.C is supplied with a protective transport case to maintain calibration and protect the instrument during handling and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40mm Universal Bore Gauge Micrometer With Interchangeable Anvils, Microcomputer Wireless+USB - Microtech Metrology
Benefit from high‑precision measurement combined with modern data transfer and modular tooling: the instrument’s 0.003 mm accuracy and Wireless and USB data output speed up inspection cycles and reduce transcription errors, while the interchangeable anvils enable flexible measurement set‑ups. Order directly via Metav Werkzeuge or consult the on‑site specialists for configuration and supply. Universal micrometer – digital bench micrometer, 0–40 mm range, Wireless + USB (Microtech Metrology) The Universal micrometer offers a compact, digital measuring solution for precise external and step measurements in workshop and production environments. Digital micrometer, 0.003 mm accuracy 0–40 mm measuring range Wireless and USB data output Interchangeable anvils (anvils not included) Precision that shortens inspection time The instrument delivers 0.003 mm accuracy, providing repeatable results for tight tolerances typical in precision engineering and quality control. With a 0–40 mm measuring range and 0.0001 mm resolution on the display, the device is suitable for small components where micrometre‑level deviations are critical. A 18 mm measuring depth supports measurements on stepped parts and constrained geometries, reducing the need for secondary fixtures and saving inspection time. Integrating measurement into the production flow Equipped with Wireless and USB data output, the device removes manual transcription and enables direct capture into inspection software or SPC systems. The digital interface supports faster batch documentation and traceability, which improves process transparency and lowers administrative overhead. Where consistent data logging is required, wireless transfer speeds up throughput and reduces human error without altering established workflows. Modular anvils for diverse measuring tasks The micrometer accepts interchangeable anvils, allowing adaptation to different workpiece shapes and contact radii; this modularity increases versatility across jobs without requiring multiple instruments. Note that anvils are not included with delivery, which makes it straightforward to select the appropriate anvil geometry for each application. The modular approach supports rapid changeovers and reduces inventory of distinct gauges. Robust design for shopfloor use Built as a workshop instrument, the device balances precision with practicality: a compact form factor and durable construction stand up to daily handling in machine shops and inspection benches. The combination of precise measurement capability and straightforward data export makes the tool well suited for toolmakers, service providers and in‑line quality checks. Microtech Metrology’s engineering ensures the unit integrates into existing measuring routines while delivering measurable gains in efficiency and reliability. Contact Metav Werkzeuge to discuss the best Universal micrometer configuration for specific applications or to confirm current stock in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 115050477 GTIN: 4061905457722 Manufacturer: Microtech Metrology Measuring range: 0–40 mm Data output: Wireless + USB Digital: yes Numbers / Core technical data Accuracy: 0.003 mm Display resolution: 0.0001 mm Measuring depth: 18 mm Measuring range min/max: 0 / 40 mm ECLASS: 21170328 Special features / Versions Interchangeable anvils — anvils not included Suitable for external and step measurements Digital data transfer for SPC integration Compact bench body for workshop use FAQ Is the micrometer suitable for routine incoming inspection? The Universal micrometer from Microtech Metrology (SKU 115050477) is designed for routine inspection work with 0.003 mm accuracy, making it suitable for incoming quality checks on small components. How is measurement data transferred to a PC? Data transfer is handled via the unit’s Wireless and USB interfaces; the Universal micrometer supports direct export to inspection software or data loggers for downstream analysis. Are the measuring anvils included with the delivery? The delivery does not include anvils; the Universal micrometer accepts interchangeable anvils, which can be selected separately to match the required contact geometry. What kinds of measurements can be performed with this instrument? The device is optimised for external and step measurements on small parts; its 18 mm measuring depth and compact frame suit stepped components and confined geometries. Can the micrometer be used on the shopfloor in continuous production? Yes. The digital output and robust construction make the micrometer appropriate for repeated use in production environments where rapid documentation and reliability are needed. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
40–50mm Digital Three-Point Internal Gauge With Carbide Measuring Faces, IP65, Setting Ring - Metav IndustryLine
Benefit from precise, wear‑resistant internal measurements thanks to carbide measuring faces and an accuracy of ±0.005 mm; the IP65 rating ensures reliable operation in workshop environments. Order the Digital three‑point internal micrometer M312.238.PN directly via Metav Werkzeuge or consult the specialists for application advice. Digital three‑point internal micrometer M312.238.PN — IP65, carbide measuring faces, 40–50 mm The Digital three‑point internal micrometer M312.238.PN is a compact, high‑precision instrument for measuring internal diameters in production, workshop and inspection tasks, ideally suited to blind‑hole checking and repeatable bore control. IP65 protection for workshop environments Carbide measuring faces for wear resistance Digital display with mm/inch and HOLD Delivered with setting ring and extension Precision and wear resistance for internal bores The three‑point design delivers a self‑centring measuring action, reducing alignment error and improving repeatability over single‑point probes. With carbide measuring faces, the instrument resists wear on contact surfaces, extending service life where frequent bore checks are required. The nominal measurement range of 40–50 mm places this instrument in the compact/micro category for fine mechanical work, offering the stiffness and short‑jaw advantage needed for small bores while maintaining practical reach for many workshop tasks. Reliable measurement under workshop conditions Built to withstand everyday shop use, the micrometer features an IP65 enclosure that protects electronics from dust and water jets, so readings remain stable even in harsher environments. The digital display supports ON/PRESET, mm/inch conversion and a HOLD function for secure reading capture; the display resolution is 0.001 mm, supporting fine adjustment and clear numerical readout. The combination of protection and a precise readout reduces scrap and rework by enabling faster, more confident decisions on the shop floor. Ready‑to‑use accessories and application focus Delivered with a setting ring and an extension, the instrument is ready for immediate zero setting and for measuring slightly recessed features. The construction and three‑point geometry make it particularly suitable for blind‑hole measurement, where consistent contact and centring across the bore diameter are essential. Compliance with DIN 863 underlines suitability for standard inspection routines, and the compact form helps to integrate the micrometer into routine quality checks without time‑consuming setup. Data transfer and quality documentation For integration into traceability workflows the micrometer provides an RB 6 data output to record results directly into data collection systems, supporting statistical process control and documentation. The instrument’s quoted accuracy of ±0.005 mm and reproducible measuring principle help to reduce process variation and speed up inspection cycles, so production throughput benefits from fewer stoppages and corrective measures. Clear numeric output and a robust mechanical design combine to support reliable quality control in small‑bore measurement tasks. For workshop‑grade, traceable bore measurement from Metav IndustryLine — the M312.238.PN three‑point digital micrometer with IP65 protection and carbide faces — contact Metav Werkzeuge by eMail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: M312.238.PN GTIN: 4054469179148 Description: Digital three‑point internal micrometer 40–50 mm, IP65, carbide measuring faces, setting ring Category: Micrometers Norm: DIN 863 Data output: RB 6 Facts Measuring range: 40–50 mm Accuracy: ±0.005 mm Display resolution: 0.001 mm Weight: 1 kg Extensions: 150 x Ø23.5 Tariff number: 90173000 Special features Carbide measuring faces IP65 protection Digital display with ON/PRESET, mm/inch and HOLD Includes setting ring and extension Three‑point measuring principle for self‑centring measurement Suitable for blind‑hole measurement Complies with DIN 863 FAQ How accurate is the micrometer for routine inspection tasks? The M312.238.PN provides an accuracy of ±0.005 mm and a display resolution of 0.001 mm, suitable for precise routine inspection and small‑bore measurement. Can the instrument measure blind holes? Yes, the three‑point geometry and included extension make the micrometer appropriate for blind‑hole measurement, ensuring stable contact across the bore. What data output is available for quality documentation? This instrument includes an RB 6 data output for direct transfer of readings into data logging or SPC systems. Is the device protected against dust and coolant? The micrometer is rated IP65, offering protection against dust ingress and low‑pressure water jets, making it robust for workshop conditions. Which accessories are supplied with the micrometer? The delivery includes a setting ring for zero setting and an extension to facilitate recessed measurements. Does the instrument comply with industry standards? The device is specified to comply with DIN 863, aligning it with common workshop and inspection requirements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40–50mm Digital Three-Point Internal Measuring Device Carbide Measuring Faces, RB6, No Setting Ring - Metav IndustryLine
The compact digital three-point internal micrometer combines 0.001 mm resolution, carbide measuring faces and an accuracy of ±0.005 mm, making it a precise, workshop-ready solution for small-bore and blind‑hole measurement; order the M312.218 directly via Metav Werkzeuge or consult our specialists if further advice is required. M312.218 — Digital three-point internal micrometer (40–50 mm) by Metav IndustryLine M312.218 is a digital three-point internal micrometer designed for precise measurement of bores and blind holes in the 40–50 mm range, suitable for fine mechanical and workshop inspection tasks. Digital display 0.001 mm resolution Carbide measuring faces for durability Accurate to ±0.005 mm Suitable for blind-hole measurement Precision where small tolerances matter The M312.218 delivers industry-grade measurement certainty by combining a high-resolution digital readout with robust measuring tips. The 0.001 mm resolution display and specified ±0.005 mm accuracy ensure repeatable results for small bore inspections, reducing downstream rework and scrap. The three-point measuring principle provides stable contact around the circumference, converting radial deviations into reliable readings — an efficient solution where consistent concentricity and roundness assessment are required. Simple operation and compatible data output Operation is straightforward: the instrument includes ON/OFF/SET, HOLD and mm/inch functions on the digital display for quick switching between units and temporary value retention. The device is supplied with an RB6 data interface for connection to inspection systems or data loggers, enabling traceable measurement records and easy integration into quality-control workflows. This combination of user-friendly controls and data connectivity supports efficient batch inspection without unnecessary complexity. Built for everyday workshop use Measuring faces are manufactured from carbide, improving wear resistance and maintaining reference geometry even under frequent contact with hard surfaces. The design omits additional extensions and a setting ring, keeping the tool compact and optimised for access into blind holes and confined geometries. With a measured weight of 2.4 kg, the instrument balances solidity with manoeuvrability, suitable for bench work and mobile inspection setups where robust handling is expected. For specialist advice or to request calibrated delivery options for Metav IndustryLine tools, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our consultants will recommend the right configuration for inspection routines and traceability requirements Technical Data Article number: M312.218 GTIN: 4054469169156 Category: Micrometer (three-point internal) Brand: Metav IndustryLine Facts Measuring range: 40–50 mm Resolution (display): 0.001 mm Accuracy: ±0.005 mm Weight: 2.4 kg Customs tariff number: 90173000 Special features Carbide measuring faces (HM) Digital display with ON/OFF/SET, HOLD and mm/inch RB6 data output No setting ring supplied No extension supplied Suitable for blind‑hole measurement FAQ What measurement range does this instrument cover? The instrument measures internal diameters from 40 to 50 mm; the M312.218 is optimised for that range. How precise is the digital readout? The display resolution is 0.001 mm and the specified accuracy is ±0.005 mm for consistent results with the M312.218. Are the measuring faces wear resistant? Yes, the measuring faces are made of carbide, ensuring long service life and stable reference geometry under normal workshop use. Can measurement data be exported to inspection software? Yes, the device features an RB6 data interface for connection to data loggers and inspection systems. Is the instrument suitable for blind‑hole measurements? The design and contact geometry are specifically suitable for blind‑hole measurement tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40–50mm Three-Point Internal Micrometer 0.001mm With Setting Ring And Extension, In Case - Metav IndustryLine
Take advantage of a precise three‑point internal measuring system combined with 1 µm resolution and hardened measuring faces for reproducible internal diameters. Benefit from a dedicated setting ring and a reach extension that simplify blind‑hole inspection. Order directly via Metav Werkzeuge or consult our technical team for integration advice. Three-point internal micrometer M312.438 — 40–50 mm, 0.001 mm resolution (Metav IndustryLine) A three‑point internal micrometer for accurate inspection of 40–50 mm bores, supplied with a setting ring and extension Three-point internal measurement 40–50 mm measuring range 0.001 mm resolution for fine control Hardened measuring faces for repeatability Accurate centring and submicron readout for internal bores The instrument is built around a three‑point measurement principle that centres automatically in the bore, reducing operator influence and yielding stable contact across the full diameter. Combined with a 0.001 mm readout this delivers fine adjustment capability; the specified measurement accuracy of ±0.005 mm provides a clear performance band for quality control tasks. The matt‑chrome‑plated scale and vernier minimise glare, supporting quick, error‑resistant readings in workshop lighting. Purpose‑designed for blind‑hole and recessed features Designed to inspect blind‑hole bores, the gauge includes a setting ring (40 mm) for straightforward calibration and an extension (152.4 mm × Ø23.5 mm) to reach recessed or deep cavities without sacrificing stability. The three‑point contact geometry distributes force evenly, so stepped and off‑centre features can be assessed with confidence. This combination of features reduces rework and shortens inspection cycles in production environments. Robust construction for repeatable workshop use Hardened measuring faces and a solid build ensure longevity under regular use; the instrument’s mass supports steady handling for precise readings. The matt‑chrome finish protects the scale and vernier from wear while keeping legibility high. For organisations seeking dependable metrology, this tool integrates into standard inspection routines and complements existing gauges and micrometres, helping to standardise measurement quality across the shop floor. For specialist advice or to secure M312.438 from Metav IndustryLine for immediate integration, contact Metav Werkzeuge and benefit from our workshop expertise and logistics in Emmerich. Technical data Article number: M312.438 GTIN: 4054469182209 Manufacturer: Metav IndustryLine Facts Measuring range: 40–50 mm Resolution/readout: 0.001 mm Measurement accuracy: ±0.005 mm Weight: 2.7 kg Setting ring: 40 mm Extension: 152.4 mm × Ø23.5 mm Hardened measuring faces: yes Special features Three‑point internal measurement system Suitable for blind‑hole bore measurement Scale and vernier matt‑chrome‑plated Designed for workshop repeatability and reduced operator influence FAQ What measuring range does the micrometer cover? The micrometer covers an internal range of 40–50 mm, ideal for medium‑sized bores and recesses. What is the resolution and typical accuracy of this instrument? Resolution is 0.001 mm with a quoted accuracy of ±0.005 mm, suitable for routine quality control and fine mechanical work. Can the micrometer measure blind‑hole bores reliably? Yes. The design is intended for blind‑hole measurements, and the included extension improves access to recessed features. How is the instrument calibrated and prepared for use? The gauge is supplied ready for workshop use; a setting ring (40 mm) is provided for quick calibration checks and routine verification. Which features improve repeatability in production use? Repeatability is supported by the three‑point contact geometry, hardened measuring faces, and the matt‑chrome scale that reduces reading errors. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40–50mm Three-Point Internal Micrometer With Carbide Measuring Faces, Adjustable Ring, 0.005mm Accuracy, Plastic Case - Metav IndustryLine
Take advantage of the carbide measuring faces, the three-point internal measuring mechanism and the fine 0.005 mm accuracy to perform repeatable checks in blind bores; order the instrument directly via Metav Werkzeuge or contact our consultants for application advice. Three-point internal micrometer M312.138 — analogue gauge with carbide faces and setting ring, 40–50 mm The Three-point internal micrometer M312.138 is an analogue measuring instrument designed for precise internal measurements in the 40–50 mm range, especially suited to blind-hole checks and workshop quality control. Three-point internal measuring system Carbide measuring faces for durability Setting ring for reference calibration Accuracy 0.005 mm for precise checks Precise internal measurement where it matters The three-point clamping mechanism provides a centred contact and stable measurement in blind bores, translating into repeatable results even on short depths. With a measuring range of 40–50 mm and an indicated accuracy of 0.005 mm, this analogue gauge is intended for workshop inspection and production sampling where quick, reliable verification of bore diameters is required. The instrument’s non-electronic design removes dependency on batteries, while the fine graduation supports visual resolution down to the specified reading step. Robust contact faces and reference calibration for production use Carbide (hard‑metal) contact faces ensure wear resistance during repeated use and preserve measurement integrity in abrasive environments. The included setting ring (Ø 40 mm) allows a simple reference check before use, shortening setup time and supporting traceable inspection routines. Constructed to meet DIN 863, the device combines traditional mechanical reliability with features that reduce rework and support consistent throughput on the shop floor. Operation, handling and shop-floor integration As an analogue instrument with a matt‑chromed scale and vernier, the gauge is straightforward to read and maintain. Its compact form factor favours quick handling for sample checks, while the three-point geometry reduces sensitivity to slight angular misalignment during insertion. For applications requiring documentation, measurement results can be recorded manually; for process advice or to discuss traceability options, Metav Werkzeuge’s technical team can assist with best-practice workflows tailored to the production environment. Contact Metav Werkzeuge today for technical guidance on the Metav IndustryLine three-point internal micrometer M312.138 and arrange delivery or further specification details via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M312.138 GTIN: 4054469119519 Category: Micrometers / Measuring instruments Facts Measuring range: 40–50 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 97 mm Standard: DIN 863 Tariff number: 90173000 Special features Carbide measuring faces (hard metal) Setting ring (Ø 40 mm) included Analogue (mechanical) instrument Suitable for blind-hole bores Scale and vernier matt chrome Delivered in transport case FAQ How is the instrument adjusted before measurement? The gauge is adjusted using the supplied setting ring (Ø 40 mm) to check and set the reference position before taking measurements, ensuring the three-point internal micrometer M312.138 reads consistently. Can the micrometer be used for blind bores only? No, the device is suitable for a range of internal measurements, but its three-point geometry and included setting ring make it especially effective for blind‑hole verification. What level of precision can be expected in routine checks? With a specified accuracy of 0.005 mm and a reading step of 0.005 mm, the instrument is designed for precise workshop checks and sampling where sub‑0.01 mm repeatability is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
425mm Dial Gauge Micrometer With 35mm Anvil, Touchscreen Display, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
The combination of ISO 17025 calibration, a 400–425 mm measurement span and wireless data transfer ensures reproducible results and seamless documentation in production environments; order the micrometer directly via Metav Werkzeuge or ask our consultants for integration advice. Digital Micrometer by Microtech Metrology — 400–425 mm, 0.01 mm accuracy, Wireless+USB A digital micrometer engineered for medium-range workshop and fixture measurement with 35 mm flat measuring faces and a touchscreen readout. Wireless and USB data output Touchscreen display 1.54" ISO 17025 calibration certificate included 400–425 mm range with Ø35 mm anvils Consistent metrology through certified calibration This instrument delivers 0.01 mm accuracy with a high-resolution reading of 0.0001 mm, offering a balance between practical robustness and precision for production use. The micrometer’s ISO 17025 calibration and accompanying certificate document traceability and reduce audit effort; calibration to this standard confirms that the measurement chain meets recognised laboratory requirements. The large Ø35 mm measuring faces expand the contact area, improving repeatability on broad surfaces while the non-rotating spindle minimises measurement error due to lateral forces and wear. Simplified data capture for quality workflows Equipped with Wireless+USB outputs and a touchscreen 1.54" display, the instrument supports rapid data transfer to inspection software and SPC systems. Digital transfer eliminates manual transcription and the associated risk of entry errors, enabling direct collection of measured values into production logs. The combination of tactile display and modern interfaces accelerates routine inspections and supports integration into connected metrology setups, making documented traceability straightforward. Medium-range capability for fixtures and assemblies With a measuring span of 400–425 mm, this tool sits in the medium-range class (300–500 mm), where reach and stiffness are carefully balanced. Such a range is well suited to checking larger jigs, housings, moulded parts and subassemblies without resorting to oversized instruments. The device’s geometry and contact diameter are chosen to preserve stability across the span, so single-operator measurements remain reproducible across typical workshop tasks. Durable operation and straightforward maintenance The digital construction reduces sensitive mechanical linkages while the non-rotating spindle and generous anvil faces reduce wear in daily use. Routine maintenance consists of keeping contact faces clean and checking zero against the supplied calibration certificate; replacement or recalibration intervals can be scheduled based on usage patterns and production requirements. The robust data interfaces and solid-state display contribute to long-term reliability and low downtime in serial inspection contexts. Contact Metav Werkzeuge to secure the ISO 17025‑calibrated Microtech micrometer (SKU 110784257) and discuss data integration or delivery options directly from Emmerich Technical data Article number: 110784257 GTIN: 4061905457609 Brand: Microtech Metrology Digital: Yes (touchscreen 1.54") Data output: Wireless + USB Display type: Touchscreen Numbers / core technical data Measuring range: 400–425 mm Reading: 0.0001 mm Accuracy: 0.01 mm Measuring face diameter: 35 mm Special features / versions ISO 17025 calibration certificate included Non-rotating spindle Large flat measuring faces (Teller Ø35 mm) Robust digital interface for integration FAQ Is an official calibration certificate included with the micrometer? Yes. The Microtech digital micrometer is delivered with an ISO 17025 calibration certificate, confirming laboratory traceability of the measurements. How can measurement data be transferred from the device? Measured values can be exported via Wireless or USB connections for direct import into inspection software or SPC systems. What measurement range and anvil size does the instrument cover? The instrument measures from 400 to 425 mm and has Ø35 mm flat measuring faces suitable for broader contact areas. What accuracy and resolution are provided? The micrometer specifies an accuracy of 0.01 mm with a digital reading resolution of 0.0001 mm. Why is the non-rotating spindle beneficial? A non-rotating spindle reduces lateral wear and the influence of spindle rotation on the workpiece, improving repeatability and prolonging anvil life. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
425mm Setting Gauge For Micrometer With Thermal Shield, Ball Measuring Faces, Accuracy ±0.005mm - Metav IndustryLine
Take advantage of the combination of high metrological accuracy, thermal protection and compact handling to secure consistent setting results for external micrometers; order the reference gauge directly via Metav Werkzeuge or consult our specialists for application advice. Setting gauge for micrometers M304.320.4 — 425 mm nominal, ±0.005 mm accuracy Setting gauge for micrometers M304.320.4 is a precision reference tool for adjusting external micrometers and verifying measurement chains in workshop and inspection environments up to 425 mm. *425 mm nominal length *±0.005 mm calibration accuracy *Spherical measuring faces, D 16 mm *Thermal protection for stable readings Dependable reference for external micrometer calibration This setting gauge serves as a reference standard for external micrometers, offering a nominal length of 425 mm and an accuracy of ±0.005 mm. Such precision places the gauge in the high‑accuracy class suitable for fine inspection tasks where repeatability matters. The stated tolerance corresponds to 5 µm, which helps reduce systematic setting errors when transferring a length value between the reference and the measuring instrument. By using a dedicated reference piece, measurement chains are shortened and the likelihood of cumulative deviations in part inspection is minimised. Construction tailored to stable measurements under changing temperatures The gauge is equipped with thermal protection, designed to reduce the influence of ambient temperature fluctuations during short‑term setting operations. The measuring faces are spherical with a diameter of D 16 mm, providing defined point contact for micrometer anvils and limiting positional uncertainty on curved or slightly irregular surfaces. Together these design elements maintain a stable contact geometry and support reproducible settings even when the workshop environment is not thermally ideal. Practical handling for routine inspection workflows With a mass of 0.7 kg, the reference piece is compact enough for straightforward handling while remaining substantial enough to sit securely during adjustment procedures. Integration into regular inspection routines is simple: set the micrometer to the gauge, verify the reading, and if necessary apply the calibration offset. The compact format supports portability between workbench and inspection station and allows technicians to keep a verified reference close at hand for frequent checks. Confidence from a specialist metrology partner As part of the Metav IndustryLine, this reference gauge reflects the distributor’s commitment to accessible precision. The combination of measurable performance characteristics and a robust design offers a pragmatic solution for workshops and small laboratories that require traceable setting aids without complex system integration. Metav’s quality filter for the European market and broad product range make the tool a reliable addition to a controlled measurement environment. Contact Metav Werkzeuge in Emmerich for technical advice and to secure the Metav IndustryLine setting gauge; eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: M304.320.4 GTIN: 4054469116730 ECLASS: 21170102 Customs tariff number: 90173000 Dimensions & accuracy Nominal length: 425 mm Accuracy: ±0.005 mm Measuring face diameter: 16 mm Weight: 0.7 kg Features & materials Spherical measuring faces Thermal protection Application: setting gauge for external micrometers Category: Accessory (metrology) FAQ What is the intended use of this setting gauge? The setting gauge M304.320.4 is intended as a precision reference for adjusting external micrometers and for short transfer checks within workshop inspection procedures. How precise is the reference and what does ±0.005 mm mean? The device provides an accuracy of ±0.005 mm (5 µm); this indicates the maximum deviation that can be expected between the stated nominal length and the actual length under normal conditions. Are the measuring faces suitable for contact with typical micrometer anvils? Yes, the spherical measuring faces with a diameter of 16 mm are designed to provide defined point contact compatible with standard micrometer anvil geometries. Is the gauge stable in typical workshop temperatures? The unit includes thermal protection to reduce short‑term thermal effects and improve stability during common workshop setting operations. Can this reference be used for calibration of large micrometers up to 425 mm? The nominal length of 425 mm makes it suitable as a reference for external micrometers and setting checks up to that length; verify compatibility with specific instrument ranges before use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
45-65mm Five-Point Outside Micrometer 0.01mm Graduation Carbide Faces Ratchet, Supplied in Case - Metav IndustryLine
Reliable five-point measuring performance with tungsten carbide measuring faces, a 0.01 mm graduation and a ratchet stop for repeatable contact pressure — order the micrometre directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine 5‑point external micrometre M309.033 — 45–65 mm, 0.01 mm graduation The 5‑point external micrometre M309.033 is a mechanical precision micrometre designed for measuring three‑ and five‑sided workpieces in the 45–65 mm measuring range. Five‑point measurement for three‑ and five‑sided parts Graduation 0.01 mm for fine readings Tungsten carbide measuring faces for wear resistance Ratchet stop for consistent measuring force Consistent accuracy where geometry matters The instrument offers 0.01 mm scale division combined with a measured accuracy of ±0.006 mm, delivering reliable repeatability for routine inspection tasks. The five‑point contact geometry stabilises the workpiece during measurement, which reduces fixturing time and the need for multiple orientations. As a result, throughput in serial checks can be increased without sacrificing the traceable precision that workshop quality control requires. Robust construction for daily shop use A lacquered frame and matt‑chrome measuring drum provide resilience against knocks and oils commonly encountered on the shop floor, while the tungsten carbide measuring faces resist wear where contact is frequent. The mechanical ratchet stop ensures a uniform measuring force on each reading, avoiding variability introduced by differing hand pressure. The instrument is wholly mechanical and analogue, offering simple, serviceable operation without dependence on batteries or electronics. Practical application and efficiency gains Designed for fast inspection of polygonal turned parts and cold‑formed profiles, the micrometre reduces handling steps for three‑ and five‑sided components by delivering a stable contact geometry. The clear graduation supports quick readings and immediate decision making at the inspection bench, helping to shorten throughput times and maintain production rhythm. For production lines and maintenance shops alike, the device provides a pragmatic balance of durability and measuring fidelity. Confidence through trusted supply and service Supplied under the Metav IndustryLine label, the instrument benefits from a distribution model focused on dependable availability and expert advice from Emmerich. Metav’s portfolio and logistics are geared to support small batches and larger replenishment needs alike, backed by decades of supply to industrial and craft customers. This underpins consistent measurement capability across the workshop and contributes to a resilient quality chain. Choose the Metav IndustryLine precision micrometre for repeatable five‑point measurement — contact Metav Werkzeuge in Emmerich for ordering and technical consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M309.033 GTIN: 4054469117645 ECLASS: 21170328 ETIM: EC003590 Customs tariff number: 90173000 Core specifications Measuring range: 45–65 mm Scale division / graduation: 0.01 mm Claimed accuracy: 0.006 mm Display type: Analogue Reading resolution (abledsung): 0.01 mm Materials & features Frame: lacquered Measuring drum: matt‑chrome Measuring faces: tungsten carbide Ratchet stop: yes Suitable for: three‑ and five‑sided workpieces Weight: not specified in data FAQ How precise is the instrument for routine checks? The micrometre offers a graduation of 0.01 mm and a stated accuracy of 0.006 mm, providing dependable precision for workshop and inspection tasks with repeatable results. Can this micrometre measure polygonal profiles? Yes, the five‑point contact geometry and carbide faces are intended for repeatable measurement of three‑ and five‑sided components, simplifying checks on polygonal turned parts. What ensures consistent contact pressure during measurement? A built‑in ratchet stop maintains uniform measuring force, which reduces operator‑induced variation and supports comparable readings across multiple checks. Is the instrument suitable for daily shop use? The lacquered frame, matt‑chrome drum and tungsten carbide faces deliver robustness for regular use in production and maintenance environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Precision micrometers built for repeatable accuracy
Micrometers—also referred to as micrometer screw gauges or micrometer callipers—are compact, robust instruments for fast, highly accurate length measurement of small to medium workpieces. Designed for routine use on the shop floor, these tools combine mechanical reliability with options for digital data capture, making them indispensable where repeatable tolerances matter.
How micrometers work and where they belong in production
Micrometers operate on a finely threaded spindle that brings two measuring faces into alignment with the workpiece; many designs follow the Abbe comparator principle so that the measuring axis and scale are collinear, reducing tilting errors. Typical outside micrometers (bühlermessschrauben) provide readings down to 1/1000 mm (0.001 mm) in analogue form; internal micrometers and specialised two- or three-point gauges enable accurate diameter and bore measurements, while depth micrometers cover depths from 0–300 mm. Hardened carbide (HM) measuring faces are standard to prevent wear and maintain accuracy over time. Digital variants offer easy reading, unit switching (mm/inch) and data output via USB, RS interface or Bluetooth; advanced models with an integrated minicomputer support Go/NoGo checks, temperature compensation and wireless transmission up to 50 m.
Practical benefits that improve shop‑floor performance
- Reduced rework and higher first-pass yield thanks to repeatable accuracy and carbide-tipped measuring faces.
- Faster, safer measurement cycles by using the ratchet/coupling to limit measuring force to 5 N to 10 N, protecting both part and instrument.
- Flexible inspection workflows with analogue, digital and minicomputer options, including wireless data transfer and mm/inch toggle.
- Versatile coverage with outside, internal, depth and built-in micrometers offering measuring ranges from a few millimetres up to 300 mm and resolution down to 2 µm (internal) or 0.003 mm (standard depth micrometers).
- Durable operation in workshop environments: mechanical models resist dust and moisture, while digital versions are available with IP54 protection.
Metav — a precision partner you can rely on
Metav combines decades of technical expertise with a broad, quality-filtered product range from its Emmerich hub. Over 48,000 customers trust Metav’s offer of more than 250,000 products, which simplifies procurement and secures reliable supply for industry, trade and specialist retailers. For buyers seeking micrometers with consistent performance and traceable data capture, Metav’s selection and technical support make it a practical, long-term choice.
In short
Micrometers provide robust, highly repeatable measurement for external, internal and depth applications, available in analogue, digital and minicomputer formats to match precision requirements and data‑management needs.
FAQ
How precise are micrometers for internal measurements?
Internal micrometers in the micrometers category can achieve accuracies around 2 µm when correctly used; digital and minicomputer models improve readout convenience and data integration for traceable inspection results.
When is a digital micrometer preferable to an analogue one?
Choose a digital micrometer when easy readout, unit conversion (mm/inch), or data transmission is required. Digital models with IP54 rating also offer dust and splash protection, while analogue micrometers remain the most robust option in harsh environments.
What measuring force should be used to ensure consistent results?
The recommended measuring force for micrometers is 5 N to 10 N. Use the ratchet or friction thimble to apply this consistent force and rely on the insulating sleeve to minimise heat transfer from the hand.
Can depth micrometers measure small bores and tight features?
Yes. Depth micrometers use a fine needle or flat measuring face and, with suitable extensions, cover narrow or deep features; standard depth micrometers typically span 0–300 mm with accuracies near 0.003 mm, while specialised digital systems offer even higher resolution.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com