Precision micrometers for reliable dimensional control
Micrometers deliver precise length and depth measurements in metalworking, enabling repeatable control over component tolerances and process stability. These instruments—available as outside micrometers, inside micrometers and depth micrometers—offer hardened contact faces and fine-thread spindles to ensure long-term accuracy and resistance to wear, with digital versions providing data transfer via USB or Bluetooth for seamless integration into inspection software. Typical uses include measuring small bores, depths and diameters in precision engineering, where features must be defined to micrometre-level accuracy; features such as ratchet thimbles and insulated frames help maintain consistent measuring force and temperature compensation. Choose between robust analog models, IP54-protected digital micrometers or micrometers with an integrated minicomputer for advanced functions like unit conversion, temperature correction and Go/NoGo evaluations.
3.5mm Special Ball Insert For Indirect Gear Tooth Thickness Measurement, Module 2 - Metav IndustryLine
Benefit from reliable, repeatable gear tooth thickness checks thanks to the 3.5 mm ball geometry, matched pair delivery and compact handling. Order the accessory directly via Metav Werkzeuge or consult our specialists for integration advice. Special Ball Insert Ø 3.5 mm for Indirect Gear Tooth Thickness Measurement — Module 2 The Special Ball Insert Ø 3.5 mm is an accessory designed for indirect measurement of gear tooth thickness on Module 2 gears, intended for use with compatible gear measurement fixtures and gauges. Module 2 compatibility for standard gear sizes 3.5 mm ball diameter for fine measurement contact Supplied as a matched pair for symmetric checks Lightweight 0.1 kg total mass for easy handling Repeatable contact geometry for trustworthy results Indirect measurement of tooth thickness relies on a defined contact geometry rather than direct thickness probing; the 3.5 mm ball diameter provides a consistent contact radius that reduces variance between checks. This results in improved repeatability and simplifies comparison across production batches. The insert's design supports standardised measurement routines for module 2 gears, helping to maintain process control and reduce rework caused by uncertain tooth profiles. Practical handling that speeds up inspection workflows Supplied pairwise, the inserts allow symmetric checks on opposing flanks without time‑consuming swapping, which streamlines quality control. At just 0.1 kg, the component is easy to fit and replace in common inspection jigs, lowering handling effort and downtime during changeovers. The accessory is particularly suitable for workshop metrology and production islands where quick, reliable checks are required within existing measuring fixtures. Clear application scope and traceability for procurement The accessory is specified for indirect gear tooth thickness measurement on Module 2 gears and is categorised as a measurement accessory. Its compact form factor and known contact diameter make it a straightforward addition to gear inspection kits. For ordering and inventory control the item is listed with GTIN and SKU, aiding traceability in procurement and stock management. Metav IndustryLine supplies this insert as a precision accessory for manufacturing and maintenance environments. Contact Metav Werkzeuge for availability and integration advice on Metav IndustryLine measurement accessories — Metav Werkzeuge GmbH in Emmerich can advise on compatibility and procurement by phone or email. Technical Data Article number: M309.186 GTIN: 4054469118635 Net weight: 0.1 kg Customs tariff number: 90173000 Facts Ball diameter: 3.5 mm Module: 2 Pack: delivered as a pair Special features Accessory for indirect gear tooth thickness measurement Category: accessory (Zubehör) Lightweight design for easy handling FAQ What is the primary purpose of this ball insert? The Special Ball Insert Ø 3.5 mm is intended for indirect measurement of gear tooth thickness on module 2 gears, providing a defined contact geometry for comparative checks. Which gear modules are supported? This insert is specified for Module 2 gears and is manufactured to match common module 2 inspection fixtures. Is the item supplied individually or as a set? The product is supplied pairwise, enabling symmetric measurements without immediate replacement or swapping. What is the ball diameter and why does it matter? The insert uses a 3.5 mm ball diameter; this fixed radius ensures consistent contact conditions and improves repeatability of thickness checks. How is the item identified for ordering and stock control? The accessory is listed under SKU M309.186 with GTIN 4054469118635 for procurement and inventory purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-35mm Three-Point Internal Micrometer Self-Centring 0.005mm Accuracy in Case - Metav IndustryLine
Take advantage of a compact, high‑precision instrument that combines 0.005 mm accuracy, a self‑centring three‑point contact and carbide measuring faces for consistent bore checks; order via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer – Metav IndustryLine · 30–35 mm · 0.005 mm The three‑point internal micrometer is a precision instrument for measuring small bores and internal diameters in precision engineering, inspection and assembly tasks. Self‑centring three‑point contact Measuring range 30–35 mm High precision 0.005 mm accuracy Carbide measuring faces Precision for reproducible internal measurements The instrument delivers 0.005 mm accuracy, supported by an analogue reading with a 0.005 mm scale that favours consistent, repeatable results in routine inspection work. The three‑point contact geometry equalises contact forces around the bore and reduces the need for elaborate alignment, so measurement time is reduced while traceability and comparability improve. This design is particularly effective where concentricity and repeatability are decisive for downstream assembly or quality acceptance. Durable contacts that keep calibration intervals long Fitted with carbide measuring faces, the micrometer preserves measuring integrity under regular workshop use. Carbide tips resist wear and abrasive surfaces, which means the instrument maintains its measuring edge over many cycles and reduces the frequency of corrective rework. The robust contact material supports stable measurement conditions, helping to protect measurement results from drift and wear-related deviation. Straightforward analogue operation for focused checks The analogue mechanism avoids electronic complexity for straightforward on‑bench verification tasks. With an intuitive mechanical feel and a clear 0.005 mm increment, the device supports fast decisions during production sampling or incoming inspection. The simple operation reduces training overhead and integrates seamlessly into established inspection routines where operators require direct tactile feedback and an immediate sense of fit. Compact range suited to fine mechanical work With a 30–35 mm measuring range this instrument sits in the compact micro class, optimised for small bores found in precision assemblies, gauges and drive components. The self‑centring feature simplifies measurement of internal diameters that would otherwise need elaborate fixturing, making the tool well suited to bench work in toolrooms, watch and instrument making, and quality‑control stations where space and handling are constrained. Metav’s IndustryLine provides this combination of precision and practicality to lower the barrier to high‑quality measurement across workshops. Contact Metav Werkzeuge for product matching and application guidance — specify the Metav IndustryLine three‑point internal micrometer M836.711 for reliable 0.005 mm results and tailored delivery from Emmerich. Technical data Article number: M836.711 GTIN: 4061905041457 Category: Messschrauben Manufacturer: Metav IndustryLine Facts Measuring range: 30–35 mm Resolution / Reading: 0.005 mm Accuracy: 0.005 mm Analogue: Yes Special features Self‑centring three‑point contact Carbide measuring faces Analogue mechanical operation eClass: 21170335 ETIM: EC003590 FAQ How precise is this instrument for internal bore measurement? The Metav IndustryLine three‑point internal micrometer M836.711 provides an accuracy of 0.005 mm with a 0.005 mm analogue reading, suitable for fine internal measurements and quality‑control checks. What measuring range does the micrometer cover? The unit covers a 30–35 mm range, placing it in the compact micro category for small bores and precision components. Are the measuring faces wear resistant? Yes — the micrometer is equipped with carbide measuring faces that offer high wear resistance and stable long‑term performance under regular workshop use. Is this instrument appropriate for workshop inspection routines? The analogue design, combined with self‑centring three‑point contact and 0.005 mm accuracy, makes the M836.711 well suited to bench inspection, incoming checks and precision assembly workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Measuring Gauge With Carbide Measuring Faces, Setting Ring, Box - Metav IndustryLine
Benefit from the combination of carbide measuring faces, a verified 0.005 mm accuracy and an included adjustment ring for consistent internal measurements; order the instrument directly via Metav Werkzeuge or consult our technical advisors for application-specific guidance. Three-Point Internal Micrometer M312.137 – 30–40 mm, carbide measuring faces (Metav IndustryLine) The Three-Point Internal Micrometer M312.137 is a precision measuring instrument intended for accurate internal diameter checks in blind and through bores within fine mechanical and workshop environments. Carbide measuring faces for long service life High precision: 0.005 mm accuracy Includes adjustment ring at 40 mm Suitable for blind-hole measurements Precision and repeatability for quality control The three-point measuring principle provides a stable contact geometry that reduces skew and improves repeatability in internal diameter measurement. With carbide measuring faces and an effective mechanical design, the instrument offers a declared accuracy of 0.005 mm, which supports reliable pass/fail decisions during incoming inspection and in-process checks. The solid contact and calibrated reference make the tool a practical choice where reproducible tolerances are required rather than occasional spot checks. Compact range tailored to fine mechanical work Classified in the micro class (measuring range 30–40 mm), this micrometer is optimised for small to medium bore diameters commonly found in precision components and assemblies. The included adjustment ring at 40 mm facilitates quick verification and calibration of the measuring span, while the three-point head adapts well to blind-hole measurement tasks. The instrument’s compact envelope allows ergonomic handling and stable positioning in confined fixtures, making it suited to watchmaking, valve seats, small housings and similar applications. Built for durability and standards compliance The scale and vernier are matt chrome finished for reduced reflection and abrasion resistance, while the carbide faces ensure longevity under frequent use. Manufactured to the requirements of DIN 863, the tool supports workshops seeking instruments that conform to established mechanical measuring norms. Delivery in a protective case ensures secure transport and storage; the robust surfaces and construction reduce the need for frequent replacement parts, lowering total cost of ownership in routine production environments. Clear reading and practical use in workshops As an analogue vernier instrument, the micrometer offers a direct mechanical reading with a fine resolution suitable for operators familiar with non-digital measurement routines. The vernier and scale arrangement gives clear incremental steps down to the declared accuracy, and the three-contact system centres inside bores to present a stable measurement reference. For process integration, the straightforward operation and minimal ancillary equipment make the micrometer an efficient tool for bench measurement, fixture setting and spot checks where fast, dependable diameter readings are required. Contact Metav Werkzeuge in Emmerich for expert advice or to request the Metav IndustryLine three-point internal micrometer M312.137; technical consultants are available to discuss suitability and delivery options. Technical Data Article number: M312.137 GTIN: 4054469119502 ECLASS: 21170335 ETIM: EC003590 Tariff number: 90173000 Core technical data Measuring range: 30–40 mm Resolution / Reading: 0.005 mm Accuracy: 0.005 mm Scope setting ring: 40 mm Length: 97 mm Standard: DIN 863 Special features Carbide measuring faces Matt chrome scale and vernier Analogue vernier instrument Suitable for blind-hole measurements Delivered in protective case FAQ How precise is the three-point measuring principle for internal diameters? The three-point head delivers stable contact and centring for internal diameters; the M312.137 provides a declared accuracy of 0.005 mm, supporting consistent quality checks. Is the instrument suitable for blind-hole measurements? Yes, the design is explicitly suitable for blind-hole measurement and the specification records compatibility with blind bores. Does the micrometer include a calibration or setting aid? An adjustment ring at 40 mm is included for scope verification; refer to the instrument documentation for recommended calibration intervals. Which standard does the micrometer comply with? The instrument is produced to the requirements of DIN 863, ensuring conformity with established mechanical measuring norms. What material finishes contribute to durability? The scale and vernier are matt chrome finished and the measuring faces are carbide, both chosen to enhance wear resistance and long-term stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Micrometer 0.001mm Resolution With Setting Ring And 152.4×Ø23.5 Extension, In Case - Metav IndustryLine
Benefit from the combination of three‑point geometry and 0.001 mm reading for highly repeatable blind‑bore inspections; the instrument’s ±0.005 mm accuracy and supplied setting ring plus extension ensure reliable reference measurements and secure handling in the workshop. Order the three‑point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three‑point internal micrometer M312.437 – 30–40 mm, 0.001 mm resolution (Metav IndustryLine) The Three‑point internal micrometer M312.437 is a precision instrument designed for internal measurements of blind bores from 30 to 40 mm, supplied with a setting ring and a deep‑reach extension for consistent, reproducible results. 0.001 mm reading Three‑point measuring principle Supplied with setting ring Extension for deep bores Exceptional precision for micro bore inspection The three‑point measuring principle delivers a centred contact on the bore, which together with the 0.001 mm reading reduces eccentricity errors and improves repeatability when inspecting small diameters. Classified in the micro range for instruments up to 100 mm, this gauge is optimised for fine mechanical components where small deviations matter. With a documented accuracy of ±0.005 mm, the device provides a measurable quality standard for routine checks and final inspection steps; this level of performance shortens decision cycles and reduces scrap in high‑precision machining. Robust design for repeatable handling Durability and handling stability are delivered via hardened measuring faces and a matt‑chrome scale and vernier, which resist wear while keeping reflections and glare to a minimum during reading. The included setting ring establishes a traceable reference, while the supplied extension (152.4 x Ø23.5 mm) allows measurement of deeper blind bores without compromising alignment. These mechanical aids translate into fewer re‑measurements and faster throughput on the shop floor, as well as consistent measurement chains for quality documentation. Practical integration into workshop workflows Designed specifically for blind‑hole measurement, the gauge adapts to common machine‑shop tasks such as bearing seat inspection, valve‑body bores and precision housings. The three‑point geometry centres in the bore automatically, which simplifies operator technique and reduces the influence of varying contact pressure. Delivered complete with protective transport case and accessories, the instrument is ready for immediate use at the inspection bench and can be introduced into existing QA routines without elaborate set‑up or additional fixturing. For reliable micro‑bore measurement choose the Metav IndustryLine three‑point internal micrometer M312.437; contact Metav Werkzeuge in Emmerich for technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application details Technical data Article number: M312.437 GTIN: 4054469182193 Weight: 2.5 kg Measuring range: 30–40 mm Reading: 0.001 mm Accuracy: ±0.005 mm Core dimensions Extension: 152.4 x Ø23.5 mm Setting ring: Ø40 mm Measuring faces: hardened Scale and vernier: matt chrome‑plated Applications & features Designed for blind bores Supplied in protective case Three‑point internal measurement Suited for micro bore work FAQ What bore range can this instrument measure? The instrument measures internal diameters from 30 to 40 mm, making it suitable for small to micro‑sized bores. Is the gauge suitable for blind‑hole measurement? Yes. The three‑point design and supplied extension make the M312.437 ideal for reliable measurement of blind bores. What resolution and accuracy does the instrument offer? The device provides a 0.001 mm reading with a stated accuracy of ±0.005 mm, offering fine resolution for quality control tasks. Are the measuring faces wear resistant? The measuring faces are hardened to resist wear and maintain accuracy during routine use. What accessories are included with the instrument? The M312.437 is supplied with a setting ring, a deep‑reach extension (152.4 x Ø23.5 mm) and a protective transport case. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Micrometer Colour 1.5" Touchscreen, Wireless/USB ISO 17025 Calibrated - Microtech Metrology
Take advantage of fully traceable, workshop-ready internal measurement: the combination of ISO 17025 calibration, a ±0.004 mm accuracy class and integrated digital output ensures reliable process control and fast data transfer for production and inspection. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three-Point Internal Micrometer — precision 30–40 mm, Wireless + USB, Microtech Metrology The Three-Point Internal Micrometer is a compact, digitally equipped instrument for precise internal diameter measurement in production, quality control and toolmaking, covering a measuring range of 30–40 mm. ISO 17025-calibrated with certificate Wireless and USB data output 1.5″ colour touchscreen display Measuring range 30–40 mm with ±0.004 mm accuracy Precision that reduces rework and inspection time The instrument uses a three-point contact arrangement to centre reliably in bores and stabilise the measurement pivot, translating into repeatable results and fewer re-measures. With a stated accuracy of ±0.004 mm and a display resolution of 0.0001 mm, the device supports tight tolerances typical in mechanical engineering and fine manufacturing. Delivered fully calibrated to ISO 17025 with a certificate, the micrometer provides documented traceability for audits and incoming inspection records. Fast, traceable digital output for statistical control Equipped with Wireless and USB data interfaces and a 1.5" touchscreen, the micrometer permits quick transfer of measured values into SPC systems or spreadsheets, reducing manual transcription errors and speeding up batch inspection cycles. The colour display simplifies reading under workshop lighting, and the digital output enables immediate integration with measurement software, shortening the path from measurement to process correction and continuous improvement. Practical design for workshop use and extended reach An included adjustment ring allows convenient zeroing and fine setting before series measurements, while the instrument’s effective measuring depth of 240 mm gives access to recessed bores and deeper assemblies without improvised extensions. The compact digital readout, robust contact points and centred three-point design make the micrometer easy to handle while preserving stiffness and repeatability, which benefits production environments where throughput and accuracy matter. Why this micrometer fits professional procurement Specifically aimed at metrology-conscious workshops, the combination of factory calibration, clear digital readout and standardised data interfaces reduces uncertainty in supplier qualification and incoming inspection. The manufacturer, Microtech Metrology, pairs this technical package with components and software compatibility suited to modern quality workflows, enabling effective shop-floor measurement without overcomplication or hidden requirements. For traceable internal diameter measurement with rapid data capture, choose the Microtech Metrology three-point internal micrometer and contact Metav Werkzeuge for procurement and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 133704010 GTIN: 4061905074257 Manufacturer: Microtech Metrology Facts Measuring range: 30–40 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 240 mm Special features Three-point internal measuring contact Data output: Wireless and USB 1.5" colour touchscreen display Adjustment ring included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered calibrated and traceable? Yes. The Three-Point Internal Micrometer from Microtech Metrology is delivered fully calibrated to ISO 17025 and includes a calibration certificate. How are measured values transferred to a computer? Measured values can be exported via Wireless or USB; the device supports direct transfer into quality software and data-collection systems for SPC. What are the accuracy and resolution specifications? The micrometer provides a resolution of 0.0001 mm and an accuracy specified as ±0.004 mm, suitable for standard industrial internal measurement tasks. Which bore sizes can be measured with this instrument? Designed for internal diameters in the 30–40 mm range, the micrometer also offers a measuring depth of 240 mm for access to recessed features. Is an adjustment or calibration ring supplied? An adjustment ring is included to facilitate zeroing and repeatable set-up before measurement series. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
30-40mm Three-Point Internal Micrometer Colour Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Compact, ISO‑certified measuring solution with integrated data transfer and high repeatability: ISO 17025 calibration with certificate, ±0.003 mm accuracy and Wireless + USB output ensure reliable measurement records and trouble‑free integration into quality workflows; order this instrument directly via Metav Werkzeuge or contact our specialists for application support. Three‑point internal micrometer — Microtech Metrology, colour touchscreen and Wireless + USB Three‑point internal micrometer for precise internal diameter control in fine mechanical and workshop inspection tasks, delivering traceable results for small bore measurement. *Three‑point measuring system for secure contact *High accuracy: ±0.003 mm specification *Colour 1.54" touchscreen display, intuitive use *Wireless + USB data output for traceable results Repeatable accuracy for small bores and fine parts The instrument is tailored for short‑range internal measurements: measuring range 30–40 mm places it in the micro class of gauges, where stiffness and reproducibility matter. With a stated accuracy of ±0.003 mm and a display resolution of 0.0001 mm, the device reduces measurement uncertainty for precision components. The three‑point contact geometry stabilises the contact points inside bores, producing a centred and repeatable reading that benefits inspection routines and acceptance testing. Fast, auditable data flow for production control Integrated Wireless + USB data output combined with a colour 1.54" touchscreen simplifies documentation and Statistical Process Control (SPC). Measurements can be transferred directly to inspection software or a data logger, reducing transcription errors and accelerating batch checks. The onboard electronics log values with the instrument’s inherent accuracy, enabling quicker decisions on process adjustments and supporting efficient quality control cycles. Ergonomic handling and practical workshop features Designed for steady one‑hand operation, the measuring screw features a compact form and an included adjustment ring to set reference points quickly. The compact measuring depths shown (97 + 150 mm) provide flexibility for different fixture setups while keeping the instrument easy to manoeuvre. The three‑point mechanism combined with the robust spindle control ensures secure contact in small bores, reducing the influence of operator force on results and improving throughput in serial inspection. Calibrated traceability for audits and production validation Delivered fully calibrated to ISO 17025, the instrument includes a formal calibration certificate, making it suitable for accredited laboratories and regulated production environments. Traceability to national standards is documented, which eases compliance during audits and supports supplier quality agreements. The combination of factory calibration, digital output and clear visual feedback from the touchscreen creates a measurement chain that is both technically rigorous and straightforward to integrate. Contact Metav Werkzeuge to specify ISO 17025‑calibrated three‑point internal micrometers with Wireless + USB output — call +49 2822 7131930 or email info@metav-werkzeuge.com for application advice and delivery from Emmerich Technical data Article number: 133504010 GTIN: 4061905041815 Manufacturer: Microtech Metrology eClass: 21170335 ETIM: EC003590 Core technical data Measuring range: 30–40 mm Resolution (display): 0.0001 mm Accuracy: ±0.003 mm Measuring depth: 97 + 150 mm Display: Colour 1.54" touchscreen Special features Data output: Wireless + USB Adjustment ring included ISO 17025 calibration certificate included Digital measurement instrument Three‑point internal measuring system FAQ What internal diameter range does the instrument cover? The measuring range is 30–40 mm, suitable for small bore inspection and classed as a micro‑range internal gauge. Is the micrometer supplied with a calibration certificate? Yes. The device is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. How are measurement values exported to inspection software? Measurement data can be exported via Wireless + USB; the digital output enables direct logging into SPC or QC systems. What accuracy and resolution can be expected during routine use? The instrument specification lists ±0.003 mm accuracy with a display resolution of 0.0001 mm, offering high repeatability for fine measurements. Does the instrument require additional accessories to perform standard checks? An adjustment ring is included for reference setting; no extra core accessories are required for standard internal diameter checks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
30-40mm Three-Point Internal Micrometer Messtrommel Scale, IP65, Digital Readout ABS/INC/UNIT, Case - Metav IndustryLine
Take advantage of precise three‑point internal measurement, robust shop‑floor protection and digital data output for reliable bore inspection; the tool’s 30–40 mm measuring range and 0.005 mm accuracy ensure reproducible results. Order the instrument directly via Metav Werkzeuge or consult the Metav team for application advice. M312.237.M — Three‑point internal micrometer, digital, IP65 (Metav IndustryLine) The M312.237.M is a digital three‑point internal micrometer designed for precise measurement of blind and through bores in workshop and inspection environments. Digital display with ABS/INC/UNIT functions Measuring range 30–40 mm with 0.005 mm accuracy Carbide measuring faces for wear resistance IP65 protection and robust drum scale Precise centring and repeatable readings for bore inspection The three‑point contact system delivers centred measuring in bores and is particularly suited to blind‑hole inspection, giving a stable reference across the measured diameter. With a measuring range of 30–40 mm and an indicated accuracy of 0.005 mm, the instrument supports fine tolerance checks typical in component inspection and quality control. The integrated drum scale provides a quick visual check while the electronic readout offers exact numerical values, combining classic mechanical reliability with modern digital precision. Built to withstand workshop conditions and everyday use Engineered for routine use, the gauge features carbide measuring faces that resist wear and hold form over prolonged cycles, while a matt‑chrome scale and vernier improve legibility under workshop lighting. The unit is rated IP65, permitting use in environments where coolant mist or dust are present without compromising the measuring mechanism. Delivered complete with a setting ring and extension, and supplied in a transport case for secure storage, the tool balances robustness with practical handling for production and toolroom teams. Traceable results and efficient data handling for quality processes A clear digital display with ON/OFF/SET and ABS/INC/UNIT controls simplifies switching between measurement modes and reference points, reducing operator errors. The integrated data output RB 4.1 enables direct transfer of readings to data capture systems or SPC software, speeding documentation and improving traceability within quality workflows. Conformity to DIN 863 underlines the instrument’s suitability for routine inspection tasks where standardised measuring practice is required. For specification checks, ordering or application guidance, contact Metav Werkzeuge in Emmerich — Metav’s technical advisers will help select the right measurement solution and arrange delivery. Technical data Article number: M312.237.M GTIN: 4054469162386 Manufacturer: Metav IndustryLine Standard: DIN 863 Category: Messschrauben Facts Measuring range: 30–40 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Length: 97 mm Weight: 2.5 kg Special features Digital display with ON/OFF/SET and ABS/INC/UNIT buttons Data output: RB 4.1 IP65 protection Carbide (HM) measuring faces Drum with scale (messtrommel mit skalierung) Scale and vernier matt chrome plated Supplied with setting ring and extension Delivered in protective case Suitable for blind‑hole (sackloch) measurements FAQ How does the three‑point system improve measurement in blind bores? The three‑point contact of the M312.237.M centres automatically in the bore, reducing eccentricity and delivering repeatable diameters even in blind‑hole conditions where conventional two‑point devices can tilt. Can the digital readings be exported to a quality system? Yes. The micrometer provides a data output (RB 4.1) for direct transfer of readings to SPC or measurement software, facilitating documentation and process control. Are the measuring faces durable for production use? The measuring faces are made from carbide, providing high wear resistance and long service life under regular shop‑floor inspection cycles. Is the instrument protected against coolant and dust? The device is rated IP65, which allows operation in environments with dust and splashing liquids typical of machining workplaces, preserving measurement integrity. What accessories are included for setup and deep bores? The micrometer is supplied with a setting ring and an extension, enabling immediate calibration and extended reach for recessed or deep bores. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Micrometer Self-Centering, Supplied in Case - Metav IndustryLine
Take advantage of the combination of compact, workshop‑grade precision and robust design for repeatable blind‑hole measurement; the self‑centring three‑point contact and hardened measuring faces deliver reliable results across production and maintenance tasks. Order the instrument directly via Metav Werkzeuge or consult our advisors for application guidance. Three‑point internal micrometer MS908.657 (Metav IndustryLine) — Self‑centring, 30–40 mm The Three‑point internal micrometer MS908.657 is a mechanically driven measuring instrument intended for precise internal diameter checks, especially blind‑hole applications in fine mechanical and light industrial environments. Self‑centring three‑point contact system Measurement range 30–40 mm Hardened measuring faces for durability Precision designed for blind‑hole measurement The three‑point geometry provides self‑centring contact inside blind holes, ensuring that the contact points align automatically with the bore axis and thereby reduce eccentricity errors. With an accuracy of ±0.004 mm and a mechanical reading of 0.005 mm, this analogue measuring instrument translates fine thread motion into dependable metrology results without electronic dependence. The three‑point contact method also helps to average minor surface irregularities, which can reduce rework and speed up routine inspection tasks, making it suitable for both small series production and maintenance checks. Compact format for fine mechanical work Classified in the Mikro range (measurement span up to 100 mm), the instrument’s 30–40 mm span and overall length of 97 mm offer a favourable balance between reach and stiffness. This makes the device well suited to precision tasks where space is limited, such as watch and instrument repair, small housings and insert fittings. The hardened measuring faces increase wear resistance and preserve measurement consistency over long service intervals, so that calibration intervals remain predictable and downtime is minimised. Workshop‑ready robustness and simple handling The analogue design emphasises mechanical reliability: a clear adjustment ring (setting ring 40) allows quick pre‑setting and repeatable contact positioning, while the compact construction withstands everyday workshop handling. Delivered in a protective case for transport, the micrometer is prepared for secure storage and movement between benches or sites. The instrument’s straightforward operation and sturdy build lower the barrier to consistent metrology in production, inspection and maintenance workflows while keeping measurement practice transparent and traceable. Contact Metav Werkzeuge today for tailored application advice on the Metav IndustryLine Three‑point internal micrometer MS908.657 and ensure the right fit for blind‑hole inspection in your workshop Technical data Article number: MS908.657 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer Suitable for: Blind‑hole measurement Core data Measurement range: 30–40 mm Length: 97 mm Accuracy: ±0.004 mm Reading (resolution): 0.005 mm Adjustment ring: 40 Mechanical type: Analogue Special features Self‑centring three‑point contact Hardened measuring faces Delivered in protective case for transport Suited to fine mechanical and light industrial use FAQ What makes the three‑point contact better for blind holes? The three‑point geometry centres itself in the bore and averages contact positions; the MS908.657 uses this principle to reduce eccentricity and provide stable internal diameter readings for blind‑hole applications. What accuracy and resolution can be expected from this instrument? The instrument offers an accuracy of ±0.004 mm with a mechanical reading of 0.005 mm, giving precise analogue measurement suitable for production checks and workshop inspection. Is the device suitable for watchmaking and small parts? Yes. With its compact dimensions and classification in the Mikro range, the micrometer is well adapted to fine mechanical work, small housings and components where a short, stiff measuring span is required. Are the measuring faces wear‑resistant? The micrometer is supplied with hardened measuring faces, which increases durability and helps maintain measurement consistency over extended use. Does the delivery include a protective case? The instrument is supplied in a protective case for transport and secure storage, making it straightforward to move between benches or sites. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-40mm Three-Point Internal Micrometer With Setting Ring And Extension, Case - Metav IndustryLine
Take advantage of the three‑point contact and 0.005 mm accuracy for dependable blind‑hole measurements; the included setting ring and extension make the instrument ready for immediate workshop use. Order or request advice directly via Metav Werkzeuge for supply and application support. Three‑Point Inside Micrometer M312.137.P — 30–40 mm range, 0.005 mm accuracy (Metav IndustryLine) Three‑point inside micrometer M312.137.P is a precision instrument for measuring internal diameters, especially designed for blind‑hole applications in fine mechanical and workshop environments Three‑point contact for blind‑hole measurement Measuring range 30–40 mm Accuracy 0.005 mm industrial grade Delivered in protective transport case Precision where blind holes matter The three‑point design provides a stable, repeatable contact geometry that centres itself inside blind holes, delivering reliable readings where standard anvil instruments struggle. With a measuring range of 30–40 mm and an accuracy of 0.005 mm, the instrument suits micro‑range tasks that demand fine tolerance control. The matt‑chrome scale and vernier reduce glare for easier reading and resist workshop wear, improving throughput by cutting rework and measurement uncertainty. Built for workshop reliability and ease of use Robust construction and an analog vernier format make the tool intuitive for technicians accustomed to mechanical gauges, while the included setting ring (Ø40) and extension (150 × Ø16.7) enable fast adaptation to different blind‑hole depths. Delivery in a protective transport case keeps the device safe during storage and transit. The weighing of components and compact design ensure ergonomic handling during repetitive checks, supporting consistent measurement practice on the shop floor. Suitable applications and practical benefits Engineered for internal diameters and blind‑hole bores, this measuring device is ideal for precision maintenance, jig and fixture checks, and assembly control in metalworking and toolmaking. The three contact points produce a centred measurement that reduces eccentricity errors; this is particularly valuable when assessing fit or clearance in tight assemblies. Accessories included with the instrument allow immediate deployment in production or inspection routines, shortening setup time and increasing operational efficiency. Contact Metav Werkzeuge for tailored advice or to arrange supply of the Metav IndustryLine three‑point inside micrometer (M312.137.P) and receive guidance on application and accessories. Technical data Article number: M312.137.P GTIN: 4054469158662 Tariff number: 90173000 Category: Messschrauben Key figures Measuring range: 30–40 mm Maximum range: 40 mm Minimum range: 30 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 90 mm Weight: 2.5 kg Special features Three‑point contact for blind‑hole measurement Analog vernier scale Scale and vernier matt‑chrome plated Includes setting ring (Ø40) Includes extension 150 × Ø16.7 Delivered in protective transport case Suitable for measuring blind holes Category: Messschrauben (inside micrometers) FAQ How does the three‑point contact improve blind‑hole measurement? The three‑point contact in the three‑point inside micrometer (M312.137.P) centres automatically in the bore, reducing eccentricity and providing more reproducible internal diameters than single‑point probes. Which measuring range does this instrument cover? This inside micrometer covers the 30–40 mm range and is supplied ready for use with the setting ring and extension included in the delivery. Is the instrument ready for workshop use straight away? Yes, the Metav IndustryLine three‑point inside micrometer M312.137.P is supplied with a setting ring and extension and arrives in a protective transport case for immediate deployment. What reading accuracy can be expected in typical use? The instrument offers a declared accuracy of 0.005 mm, suited to micro‑range precision tasks and repeatable dimensional checks in production environments. Can the device be used for depth or step measurements? The tool is optimised for internal diameter measurements and blind holes; specialised applications such as depth or step measurement are outside its primary design but may be approached using appropriate extensions and fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30-50mm Digital Three-Point Internal Measuring, Two Heads, HM Measuring Faces, IP65, With Setting Ring And Extension - Metav IndustryLine
Take advantage of high-precision measurement, robust protection to IP65 and carbide contact faces for reliable internal inspections; the instrument’s ±0.005 mm accuracy and included setting ring with extension support consistent results in blind-hole applications. Order the M312.287.PN directly via Metav Werkzeuge or contact our consultants for specification matching. M312.287.PN — Digital three-point internal micrometer, 30–50 mm, IP65 The M312.287.PN is a digital three-point internal micrometer designed for precise internal diameter measurement in tight and blind-hole environments, combining a sealed construction with carbide contact faces for workshop and production use. Digital three-point internal measurement 30–50 mm Two measurement heads with digital display Carbide measuring faces, protected to IP65 Delivered with setting ring and extension Precise, repeatable readings for critical bore inspection The instrument delivers an accuracy of ±0.005 mm, making it suitable where narrow tolerances are required. The digital display includes ON/PRESET, mm/inch and HOLD functions to support repeatable documentation of readings, while the two measuring heads provide stable contact with the bore during rotation. Compared with standard digital callipers, this device is tailored to interior diameters and blind-hole tasks, offering a measurement concept that reduces operator-induced variation and improves throughput in routine inspections. Rugged design for the shop floor and protected measurement heads A sealed housing with IP65 protection guards electronics against coolant and dust, allowing the device to be used near machining operations without immediate risk to the display. The carbide measuring faces ensure long-term wear resistance when probing metallic bores, and the instrument’s overall construction balances robustness with handling convenience. Supplied in a transport box, the micrometer is ready for stable storage and safe movement between measuring stations. Simple setup, calibration traceability and practical operation The tool includes a setting ring and an extension (150 mm) for flexible adaptation to different bore depths, and the measuring depth of 105 mm extends capability into deeper cavities. The DIN 863 conformity provides a familiar reference for workshop technicians; calibration and adjustment procedures align with industry practice so that measurement chains remain auditable. The digital readout’s mm/inch toggle and HOLD function simplify data capture and reduce transcription errors during quality control. Application-focused benefits and typical use cases Engineered for blind-hole and internal bore inspection in precision assemblies, the device performs especially well in watchmaking, instrument parts, mould inserts and small housing bores where a compact measuring range is required. Classified in the micro category (max range up to 100 mm), this instrument offers the stiffness and fine resolution expected for small-bore metrology, while features such as the sealed electronics and carbide faces extend its service life in mixed production environments. Contact Metav Werkzeuge for an application review and secure the M312.287.PN for consistent, shop-floor-ready internal measurements Technical Data Article number: M312.287.PN GTIN: 4054469179285 Manufacturer: Metav IndustryLine Protection rating: IP 65 Standard: DIN 863 Display functions: ON/PRESET, mm/inch, HOLD Facts Measuring range: 30–50 mm Accuracy: ±0.005 mm Measuring depth: 105 mm Weight: 2.2 kg Extension: 150 mm Tariff number: 90173000 eCl@ss: 21170335 ETIM: EC003590 Special features Two measurement heads with digital readout Carbide (HM) measuring faces Suitable for blind-hole measurement Supplied with setting ring and extension Kitted in transport box for safe handling FAQ How precise is the measurement with this instrument? The M312.287.PN achieves an accuracy of ±0.005 mm, delivering high-resolution readings suitable for precision internal bore inspection. Can the device be used in wet or dirty workshop conditions? Yes, the instrument is rated IP65, which protects the electronics from dust and low-pressure water jets commonly encountered near machining centres. Is the M312.287.PN suitable for blind-hole measurements? The instrument is explicitly designed for blind-hole use and is supplied with a setting ring and extension to facilitate measurement in recessed bores. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300-325 mm Digital Three-Point Internal Gauge For Blind Holes, Carbide Measuring Faces, Data Output RB 4 - Metav IndustryLine
Take advantage of precise blind‑hole measurement with a 300–325 mm range and robust carbide measuring faces that deliver repeatable results; the instrument's 0.012 mm accuracy and digital readout speed up inspection cycles. Order the digital three‑point internal micrometer directly via Metav Werkzeuge or consult our specialists for application advice. Digital three‑point internal micrometer M312.266.S — 300–325 mm range, carbide faces (Metav IndustryLine) The Digital three‑point internal micrometer M312.266.S is a purpose‑built instrument for accurately measuring blind holes in production and workshop inspection, combining a long reach with a stable three‑point contact system. 300–325 mm measuring range Carbide measuring faces for wear resistance Digital display with mm/inch and hold functions Designed for blind‑hole measurement Precision where blind‑hole accuracy matters A three‑point contact system converts radial geometry into a single, repeatable diameter value, making it ideal for Sackloch (blind‑hole) inspection where single‑point probes can slip. The device achieves an accuracy of 0.012 mm, which supports reliable quality control across medium‑sized components. The 300–325 mm range places this instrument in the mid‑range class, suitable for larger fixtures and mould halves while retaining manoeuvrability. With carbide measuring faces, the contact surfaces resist wear under repeated use, extending service intervals and reducing measurement drift. Faster readings and fewer processing errors The digital readout is equipped with ON/0, mm/inch, ABS, PRESET and HOLD keys to streamline reading and data capture. Quick unit switching and preset functions reduce calculation steps and speed up batch inspections, while the hold feature freezes unstable readings for clear documentation. The instrument's resolution of 0.001 mm (display) ensures discernible changes are visible to the operator, supporting faster decision‑making on the shop floor. These features lower cycle time and minimise manual transcription errors when results are transferred to inspection reports. Built for workshop integration and traceable results Connectivity is provided via RB 4 data output, enabling direct transfer of measurement values into SPC or inspection software for traceability. The micrometer is supplied without an adjustment ring and is delivered in a transport case for secure handling and storage, aiding organisation in busy production environments. Weighing approximately 5 kg, the instrument is stable during measurement yet portable enough for bench or in‑machine use. This combination of digital interfacing and robust construction makes it suited to repeatable inline checks and workshop quality assurance. For precision blind‑hole measurement choose the Metav IndustryLine digital three‑point internal micrometer and request tailored supply or technical consultation from Metav Werkzeuge GmbH by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M312.266.S GTIN: 4054469159058 Tariff code: 90173000 Manufacturer: Metav IndustryLine Facts Measuring range: 300–325 mm Measuring depth: 140 mm Readout resolution: 0.001 mm Stated accuracy: 0.012 mm Weight: 5 kg Digital: yes Data output: RB 4 Special features Three‑point internal measurement Carbide measuring faces Digital display with ON/0, mm/inch, ABS, PRESET, HOLD Delivery without setting ring Supplied in transport case Designed for blind‑hole measurement Category: Micrometers (internal) FAQ How does the three‑point measurement improve blind‑hole readings? Three contact points average circumferential variation into a single diameter value; the design of the Digital three‑point internal micrometer M312.266.S reduces positional error in blind‑hole applications and yields more repeatable results than single‑point probes. Is the device compatible with data acquisition systems? Yes. The instrument features RB 4 data output, allowing measured values from the Metav IndustryLine digital three‑point internal micrometer to be transferred directly to inspection software or SPC systems. What is included with delivery and what is missing? Delivery includes the instrument in a transport case for secure handling. The micrometer is supplied without a setting ring; if a reference ring is required it must be ordered separately. For which workshop tasks is this instrument best suited? The micrometer is intended for medium‑range internal inspections—vices, housings and blind holes—where 300–325 mm reach and high repeatability are required; it balances reach and stiffness for typical machining and assembly inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300-325mm Three-Point Inside Micrometer Ratchet, Matt Chrome Scale And Vernier, 0.012mm Accuracy, Plastic Case - Metav IndustryLine
Take advantage of precise internal measurement and robust workshop handling: the combination of a 300–325 mm measuring range, an accuracy of ±0.012 mm and a ratchet stop ensures reproducible results for medium‑sized bores and fixtures. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point inside micrometer M312.156 — three‑point inside micrometer, 300–325 mm range, ratchet stop (Metav IndustryLine) The three‑point inside micrometer M312.156 is a precision instrument for internal diameter measurement in jig, mould and general industrial metrology, providing stable contact in medium‑sized bores. Medium range 300–325 mm for larger components Analogue vernier resolution 0.005 mm Ratchet stop for constant measuring force Matte chrome‑plated scale and vernier Precise, repeatable internal measurement for production control The three‑point contact spindle design gives a stable, concentric seating inside bores, reducing eccentricity and improving repeatability. With an indicated accuracy of ±0.012 mm and a vernier resolution of 0.005 mm, this analogue instrument is intended for routine quality control where reliable numeric comparability is required. The ratchet stop maintains a consistent measuring force so measurements are less dependent on operator technique, which supports tighter process control and reduces scrap rates. Robust engineering that suits busy workshops Built for repetitive use, the instrument features a matte chrome‑plated scale and vernier for clear reading and good wear resistance. The measuring depth of 140 mm and sturdy body construction make it suitable for measuring recesses and larger internal features without compromising stiffness. Hardened measuring faces are included to withstand contact wear, and the delivery in a protective case supports safe transport between job sites and polishing benches. Optimised for medium‑range internal diameters With a measuring span of 300–325 mm, this device falls into the medium class of internal measuring tools: long enough to reach larger fixtures and housings, yet compact enough to be manageable by a single operator in most setups. That positioning makes it particularly useful in toolrooms, mould shops and medium‑series production where balance between reach and rigidity is essential for reproducible results. Practical workflow features to speed up inspections The analogue vernier operation avoids dependence on batteries and simplifies long‑term serviceability; the ratchet provides tactile control for consistent readings and the instrument’s weight and build quality aid in stable handling. Note that the instrument is supplied without a setting ring, so calibration or setting with a suitable reference standard is required before first use. The absence of electronic data output reflects a focus on rugged, low‑maintenance measurement routines. Choose the Metav IndustryLine three‑point inside micrometer M312.156 for dependable medium‑range internal measurement — contact Metav Werkzeuge in Emmerich for tailored advice or to place an order (info@metav-werkzeuge.com | +49 2822 7131930) Technical data SKU: M312.156 GTIN: 4054469119632 Category: Micrometers (Messschrauben) eClass: 21170335 ETIM: EC003590 Facts Measuring range: 300–325 mm Measuring depth: 140 mm Resolution (vernier): 0.005 mm Accuracy: ±0.012 mm Weight: 12 kg Tariff code: 90173000 Special features Matte chrome‑plated scale and vernier Analogue instrument with vernier reading Ratchet stop for constant measuring force Hardened measuring faces Delivered in protective case Supplied without setting ring Category: three‑point inside micrometer FAQ What measuring range does this micrometer cover? The three‑point inside micrometer M312.156 covers a measuring range of 300–325 mm, suitable for medium‑sized internal diameters. How fine is the reading on the instrument? The instrument provides a vernier resolution of 0.005 mm and an indicated accuracy of ±0.012 mm for consistent inspection results. Is a setting ring included with delivery? No, delivery of the Metav IndustryLine M312.156 is without a setting ring; a reference standard is required to set the instrument before first use. Does the micrometer include hardened measuring faces? Yes, the M312.156 is supplied with hardened measuring faces to ensure long‑term wear resistance during repeated contact measurements. Can the instrument be used without batteries or electronics? Yes, the analogue vernier operation of the M312.156 requires no batteries, prioritising ruggedness and low maintenance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300-325mm Three-Point Internal Micrometer Digital, 0.001mm Resolution, Hardened Measuring Faces, Supplied in Case - Metav IndustryLine
Take advantage of precise digital measurement, robust hardened measuring faces and a long 300–325 mm range to secure consistent internal diameters and faster setup in production. Order the three-point internal micrometer directly via Metav Werkzeuge or ask our consultants if needed. Three-point internal micrometer M312.266 — Digital internal micrometer, 300–325 mm, Metav IndustryLine A three-point internal micrometer M312.266 for accurate large-bore measurements in toolmaking, fixture construction and component inspection Digital display with mm/inch, ABS and HOLD Measuring range 300–325 mm Hardened measuring faces for wear resistance RB 4 data output for digital traceability Confident internal measurements with measurable precision The three-point measuring principle ensures stable contact across the bore and, combined with a measuring range 300–325 mm, provides reproducible readings for medium-to-large internal diameters. The instrument offers accuracy 0.012 mm and a fine resolution 0.001 mm, values that translate into fewer reworks and reliable quality control steps. The substantial measuring depth 140 mm permits measurement of recessed bores and stepped components without auxiliary fixtures, helping to standardise inspection routines on shop floors and in quality labs. Built for repeatability and straightforward handling Robust construction and hardened measuring faces reduce wear under continuous use, extending the tool’s service life in busy production environments. The digital display includes ON/0-, mm/inch-, ABS-, PRESET- and HOLD-touches to speed up setup and avoid manual transcription errors. Supplied without a setting ring, the instrument integrates into existing calibration procedures and is suited to fixed inspection benches or portable verification tasks. The device’s mass (approx. 5 kg) adds stability during measurement, improving repeatability for heavier or awkward components. Streamlined data transfer and procurement-friendly details Equipped with RB 4 data output, the micrometer transfers measurements to SPC or inspection software for traceable records and Process Control integration. The robust specification supports documentation requirements across manufacturing and inspection chains, and the included classification details simplify ordering and customs handling. The tool is therefore well suited to workshops and production lines that require both hands‑on reliability and digital traceability to meet modern quality standards. Choose the Metav IndustryLine three-point internal micrometer for dependable large-bore measurement—contact Metav Werkzeuge for technical advice or to arrange supply. Technical data SKU: M312.266 GTIN: 4054469159034 Eclass: 21170335 ETIM: EC003590 Tariff number: 90173000 Facts Measuring range: 300–325 mm Accuracy: 0.012 mm Resolution (reading): 0.001 mm Measuring depth: 140 mm Weight: 5 kg Special features Digital display with ON/0-, mm/inch-, ABS, PRESET and HOLD RB 4 data output for digital measurement transfer Hardened measuring faces for wear resistance Supplied without setting ring FAQ What measurement range does this micrometer cover? The three-point internal micrometer covers a 300–325 mm measuring range suitable for medium-to-large bores in fixtures and housings. What resolution and accuracy can be expected? Resolution is 0.001 mm and the stated accuracy is 0.012 mm, providing the precision required for routine production checks and component inspection with the Metav IndustryLine micrometer (M312.266). Is the instrument ready for digital data capture? Yes. The device features an RB 4 data output, enabling direct transfer of measured values into SPC or inspection systems. Are measuring faces treated to resist wear? The micrometer is supplied with hardened measuring faces, which improves durability and maintains measurement consistency under regular use. Is a setting ring included for calibration? Delivery is without a setting ring; calibration or presetting should be performed with existing workplace standards or with a separately ordered setting ring. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300-400mm Digital Outside Micrometer With Ratchet Stop, IP65, Calibrated To ISO 17025 - Microtech Metrology
Take advantage of the combination of high-resolution digital reading, IP65 protection and an ISO 17025 calibration certificate for reliable measurement in production and quality control. Order the measuring instrument directly via Metav Werkzeuge or ask our consultants if needed. Outside micrometer by Microtech Metrology — digital, IP65, 300–400 mm range The Outside micrometer is a digital, large-range micrometer designed for robust external measurements of medium-sized components in workshops and inspection rooms. Digital display with 0.001 mm resolution IP65 protection for harsh workshop conditions Ratchet stop for consistent measuring force ISO 17025 calibration certificate included Reliable precision for medium-sized components This measuring instrument is specified for a 300–400 mm measuring range, which places it in the medium class suitable for fixtures, housings and larger assemblies where reach and stiffness must be balanced. The tool combines a fine 0.001 mm display resolution with a stated accuracy of ±0.007 mm, allowing objective repeatability for production checks and incoming inspection. The digital readout simplifies data capture and reduces transcription errors compared with mechanical readings, increasing process reliability in machining and QA workflows. Built to withstand workshop conditions and keep measuring reproducible The micrometer is rated IP65, which means it is dust-tight and protected against low‑pressure water jets, so routine cleaning and typical shop-floor exposure do not compromise the electronics. The Ø25 mm measuring faces provide stable contact for larger profiles while the integrated friction ratchet (ratchet stop) enforces a consistent measuring force, reducing variance caused by operator pressure. Weighing approximately 1.9 kg, the instrument balances rigidity and handling for single-person use while remaining substantial enough to avoid unwanted flex during measurement. Traceable calibration for quality assurance and immediate use Delivered with a full ISO 17025 calibration certificate, the instrument arrives ready for quality‑assured tasks and is suitable for certified test benches and documented inspection procedures. Included setting rods enable quick verification and adjustment on site before first use, saving setup time. The calibration under ISO 17025 ensures traceability and acceptance in regulated environments; the certificate documents measurement uncertainty and supports audit evidence in supplier or customer quality checks. Faster, safer measurement and fewer reworks A clear digital display combined with the ratchet mechanism improves throughput: measurements are taken faster and with reduced operator influence, which can decrease scrap and rework. The solid digital head is engineered for repetitive use in production and inspection, while the included calibration documentation means the instrument can be integrated into measurement routines without delay. For applications where consistent external measurement of medium-sized parts is essential, this micrometer offers a practical blend of durability, precision and traceability. Contact Metav Werkzeuge today for advice on suitability for specific parts and to secure the Microtech Metrology outside micrometer with ISO 17025 calibration for your workshop Technical data Article number: 110174001 GTIN: 4061905039270 Manufacturer: Microtech Metrology Facts Measuring range: 300–400 mm Resolution: 0.001 mm Accuracy: ±0.007 mm Measuring faces: Ø25 mm Weight: 1.9 kg Protection class: IP65 Display: digital Calibration: ISO 17025 certificate included Special features Ratchet stop (friction ratchet) Setting rods included Digital micrometer head Large measuring range for medium components FAQ Is the micrometer suitable for production inspection of medium-sized parts? The micrometer from Microtech Metrology is specified for a 300–400 mm range and is intended for medium-sized components, making it suitable for production inspection and quality checks. What level of accuracy and resolution does the instrument offer? The instrument provides a resolution of 0.001 mm and a stated accuracy of ±0.007 mm, which supports repeatable measurements for standard workshop and quality‑control tasks. Does the delivery include calibration documentation? Yes. The outside micrometer is supplied with an ISO 17025 calibration certificate, enabling immediate use in traceable inspection routines. How does the ratchet stop improve measurement consistency? The ratchet stop ensures a reproducible measuring force so readings are less affected by operator pressure, improving comparability across multiple measurements. Is the device protected against dust and water on the shop floor? The micrometer is IP65-rated, meaning it is dust-tight and protected against low-pressure water jets, suitable for typical workshop environments. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
300-400mm Large-Range Electronic Micrometer With Colour Touchscreen, ISO 17025 Calibration Certificate - Microtech Metrology
Combine a wide 300–400 mm measuring range, sub‑5 µm accuracy and wireless plus USB data transfer to streamline quality checks and traceable documentation; order the micrometer directly via Metav Werkzeuge or ask our consultants if needed. Microtech Metrology Outside Micrometer 300–400 mm — Digital, ±0.005 mm accuracy A Microtech micrometer engineered for high‑precision outside measurements in production and quality control, offering digital readout and industrial data connectivity. 300–400 mm medium measuring range High precision ±0.005 mm accuracy Wireless and USB data transfer ISO 17025 calibration certificate included Reliable measurement for medium‑sized components Placed in the Medium range (300–500 mm) category, this outside micrometer combines reach and rigidity for measurements of fixtures, housings and larger assemblies without compromising handling. The instrument delivers a measuring range of 300–400 mm together with an accuracy of ±0.005 mm, which supports tight tolerance control in component inspection and process validation. The generous Ø25 mm measuring faces ensure stable contact over larger diameters, reducing form‑related errors and improving repeatability on stepped or curved surfaces. Integrated digital workflow to speed up inspection Modern quality systems demand reliable data transfer; this micrometer provides wireless and USB options and an internal memory capable of storing 2000 values, cutting out manual transcription and shrinking inspection cycles. The colour 1.5‑inch touchscreen offers immediate visual feedback and straightforward menu navigation, while support for app synchronisation and optional industrial interfaces enables seamless connection to SPC systems and manufacturing execution systems. The result is faster reporting, fewer transcription errors and a clearer audit trail for production runs. Robust construction and traceable calibration for shop‑floor confidence Manufactured with a CNC‑machined aluminium housing, the instrument resists everyday shop impacts while keeping thermal drift low, and its compact mass of 1.9 kg aids stable handling during repetitive checks. Delivered with an ISO 17025 calibration certificate, the micrometer arrives ready for use in accredited measurement programmes, providing comparability and documented traceability for internal quality control or supplier validation. The built‑in microcomputer functions support on‑device statistical checks and reduce setup time between measurement tasks. Contact Metav Werkzeuge for tailored advice on integrating this Microtech outside micrometer into the metrology workflow or to place an order — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 110184008 Manufacturer: Microtech Metrology GTIN: 4061905039485 Weight: 1.9 kg Measuring range: 300–400 mm Accuracy: 0.005 mm Measuring faces: Ø25 mm Data output: Wireless + USB Display: Colour 1.5" touchscreen Calibration: ISO 17025 certificate included Core specifications Measuring range (min–max): 300–400 mm Maximum measuring range mm: 400 Resolution / accuracy: ±0.005 mm Memory capacity: 2000 values Mass: 1.9 kg Special features CNC‑machined aluminium housing Integrated microcomputer and touchscreen Wireless connectivity and USB transfer Optional Modbus RTU for industrial integration Delivered with ISO 17025 calibration certificate (Ilac MRA) FAQ What measuring range does this micrometer cover? The micrometer covers a measuring range of 300–400 mm, classified in the medium category suitable for larger workshop components. Is the instrument delivered calibrated? Yes, the device is supplied with an ISO 17025 calibration certificate, ensuring traceability and suitability for accredited measurement processes. How is measurement data transferred from the micrometer? Measurement data can be transferred wirelessly or via USB; the instrument also stores up to 2000 values for batch transfer and review. Which manufacturer produces this micrometer? This micrometer is produced by Microtech Metrology; the item is listed under SKU 110184008. Microtech Metrology: Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
3000-4000mm Bench Micrometer Modular Wireless Colour Touchscreen, IP65, ISO17025 - Microtech Metrology
Combine modular construction, wireless data transfer and an ISO 17025 calibration certificate to secure reproducible, large‑format measurements with minimal setup time. Order the DataMet wide‑range modular micrometer directly via Metav Werkzeuge or ask our consultants if needed. DataMet Wide‑Range Modular Micrometer — modular, Industry 4.0 ready (Microtech Metrology) A DataMet Wide‑Range Modular Micrometer engineered for precise dimensional control of large components in heavy machining and Industry 4.0 production environments. Modular construction for easy transport and assembly Wireless and USB data transfer options ISO 17025 calibration certificate included IP65 protection and CNC‑machined aluminium housing Precise, repeatable measurement for large components The modular design delivers reproducible measurements across long spans: built as a segmented system, the instrument is tailored for components that exceed conventional micrometer lengths. With a measuring range of 3,000–4,000 mm and sub‑micron reading capability down to 0.0001 mm, the system reduces rework and inspection cycles for large shafts, pipe sections and gear blanks. The patented MICS electronics stabilise readings and provide linear and temperature correction, which together improve process reliability when measuring heavy or thermally sensitive parts. Seamless digital workflow for efficient quality control Designed for integration into modern inspection routines, the micrometer supports Wireless and USB transfer modes, wireless HID and app synchronisation via the MDS application for Windows, Android, iOS and macOS. A memory manager holds up to 2000 values with folder and statistics functions, allowing quick batch logging and off‑line analysis. These features cut manual data entry, speed up traceability and facilitate Industry 4.0 connectivity where automated logging and live graphs feed production control systems. Robust engineering for workshop and shopfloor use The instrument’s CNC‑machined aluminium housing and IP65 rating protect sensitive electronics against dust and water jets while maintaining a rigid measuring frame. Large Ø50 mm measuring faces and a sectional assembly keep deflection low over long lengths; the modular concept also means transport and on‑site assembly can be handled efficiently without compromising stiffness. For demanding environments, the solid aluminium block construction and protective rating translate into lower downtime and longer instrument service life. User‑focussed controls and traceable calibration Operation is simplified by a colour touchscreen with graphic displays, Go/NoGo, max/min, formula and timer functions, plus temperature compensation to maintain measurement integrity. The system includes a full calibration certificate performed to ISO 17025 (Ilac MRA), which is supplied with the instrument and secures traceability for quality audits. Optional MODBUS RTU output is available for direct industrial connections when live process data is required. Choose Microtech Metrology’s modular DataMet system for dependable, traceable large‑format measurement; contact Metav Werkzeuge in Emmerich for tailored advice and procurement support via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 110160405 GTIN: 4061905040122 Manufacturer: Microtech Metrology SKU: 110160405 Core specifications Measuring range: 3,000–4,000 mm Resolution (display): 0.0001 mm Accuracy: 0.06 Weight: 47 kg Measuring faces: Ø50 mm Modules: 4 IP rating: IP 65 Display: Colour 1.5" touchscreen Memory capacity: 2000 values Special features Modular construction for segmented assembly Wireless + USB data transfer; wireless HID modes MICS system with sub‑micron electronics and compensation MDS app compatibility (Windows, Android, iOS, macOS) CNC‑machined aluminium housing ISO 17025 calibration certificate included Optional MODBUS RTU (RS‑485) industrial output Patents: UA108044, UA99686, UA2022050400 FAQ What measurement range does the instrument cover? The DataMet wide‑range modular micrometer from Microtech Metrology covers a measuring range of 3,000–4,000 mm, making it suitable for large shafts, pipes and heavy components (SKU 110160405). Is the micrometer supplied with a traceable calibration certificate? Yes; the instrument is delivered with an ISO 17025 calibration certificate (Ilac MRA), ensuring laboratory traceability and suitability for quality audits. How is measurement data transferred and stored? Measurement data can be transferred wirelessly or via USB, with support for wireless HID modes and direct synchronisation to the MDS app; onboard memory stores up to 2000 values. Which environments is this micrometer designed for? With a CNC‑machined aluminium housing and IP65 protection, the system is designed for workshop and shopfloor conditions where dust and occasional moisture are present. How long does modular assembly take and who benefits most? The modular sections are engineered for efficient assembly and transport; the system is especially valuable for manufacturers in heavy machining, mould and fixture construction, and large‑diameter component production. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
300mm Depth Gauge Flat Jaw 0.01mm Resolution 100mm Bridge Includes 12 Probe Rods, Ratchet, Cased - Metav IndustryLine
Take advantage of the combination of reliable 0–300 mm measuring range, 0.01 mm resolution and a ratchet stop for reproducible measuring force; this depth micrometer supports a smooth inspection routine and reduces rework. Order the instrument directly via Metav Werkzeuge or consult the technical team for application advice. Metav IndustryLine Depth Micrometer M309.072 — 0–300 mm, 0.01 mm resolution A Metav IndustryLine Depth Micrometer M309.072 designed for standard workshop and machine‑shop depth measurements, supplied with interchangeable measuring rods for flexible use. Depth micrometer, 0–300 mm range 0.01 mm resolution for precise readings Flat measuring faces with ratchet stop Interchangeable measuring rods for flexibility Precise standard-range measurement for everyday production The instrument belongs to the Standard measuring class (maximum range up to 300 mm), which offers an optimal balance of reach, stiffness and one‑hand usability for general machine‑shop work. With a resolution of 0.01 mm and a measured accuracy of 0.007 mm, the device provides reliable numerical data for in‑process checks and routine quality control. The combination of fine resolution and proven mechanical construction reduces uncertainty in repeated depth measurements, supporting efficient process control and fewer rejects. Practical handling and modular measuring system Interchangeability of the measuring inserts allows quick adaptation to diverse depth tasks: the delivery includes 12 measuring rods, permitting measurement of varying recess depths without cumbersome tool changes. The ratchet stop ensures consistent contact pressure, which counters operator variability and improves repeatability. Flat measuring faces simplify alignment against broad reference surfaces, while the compact 100 × 16 mm bridge offers stable support in confined areas. Together these features shorten setup times and make the micrometer suitable for batch or single‑piece inspection. Robust analogue design optimised for workshops An analogue readout with a clear 0.01 mm scale provides immediate, intuitive feedback, avoiding dependencies on batteries or digital interfaces in harsh environments. The construction emphasises longevity and straightforward maintenance: replaceable measuring inserts and a simple mechanism reduce downtime and facilitate quick service. The tool is thus a pragmatic choice for workshop teams who prioritise durable instruments that integrate into existing inspection routines without complex training. For dependable depth measurement in standard workshops, select the Metav IndustryLine M309.072 depth micrometer and contact Metav Werkzeuge in Emmerich for tailored technical advice and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M309.072 GTIN: 4054469117768 eClass: 21170350 ETIM: EC003590 Customs tariff number: 90173000 Facts Measuring range: 0–300 mm Resolution / scale: 0.01 mm Accuracy: 0.007 mm Bridge size: 100 × 16 mm Measuring rods included: 12 Special features Analogue readout Flat measuring faces Ratchet stop for constant measuring force Interchangeable measuring rods / easy replacement of inserts Supplied accessories: measuring rods (12 pieces) FAQ Is the micrometer suitable for general machine‑shop depth measurements? Yes. The Metav IndustryLine Depth Micrometer M309.072 is designed for standard workshop and machine‑shop depth measurements up to 300 mm, offering a practical combination of reach and rigidity. How is repeatability ensured during repeated measurements? Repeatability is supported by the ratchet stop and flat measuring faces; consistent contact pressure and stable seating help the M309.072 produce reproducible results. Are measuring rods included and changeable? The delivery contains 12 measuring rods and the design allows straightforward replacement of the measuring inserts to adapt to different depth tasks. What accuracy and resolution can be expected? The micrometer provides a resolution of 0.01 mm and an accuracy of 0.007 mm, suitable for routine quality checks and production control. Is the readout digital or analogue? This instrument features an analogue readout with a clear 0.01 mm scale, avoiding dependency on electronics while remaining easy to read. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300mm Depth Micrometer Digital With ON/ABS/Set/Hold, Friction Ratchet, IP65 - Microtech Metrology
Take advantage of precise digital measurement, robust workshop protection and factory calibration to keep quality control reliable and traceable; order directly via Metav Werkzeuge or consult our specialists for application advice. Depth micrometer by Microtech Metrology — digital, 0–300 mm range The depth micrometer delivers digital depth measurement for workshop and inspection use across a 0–300 mm range, suitable for standard machine‑shop tasks. Digital readout with 0.001 mm resolution Calibrated to ISO 17025, certificate included Protection class IP65 for harsh environments Integrated friction ratchet for consistent measuring force Precise measurement with laboratory traceability The instrument provides a resolution of 0.001 mm and an operational accuracy of ±0.008 mm, delivering the repeatability needed for component inspection and in‑process checks. Because the device is supplied fully calibrated to ISO 17025, a calibration certificate accompanies each unit, ensuring measurement results are traceable and admissible for quality records. This combination of fine resolution and certified accuracy reduces rework and supports documented quality systems in production and QA laboratories. Robust design for everyday workshop use Designed for practical handling, the gauge features a sealed housing rated IP65 and an integrated friction ratchet that standardises contact pressure for repeatable readings. The digital display offers ON/ABS, SET and HOLD functions plus a quick mm/inch toggle, which speeds up routine measuring tasks and reduces operator error. These features provide a straightforward workflow: fast data capture, reliable protection against coolant and dust, and comfortable handling during frequent use. The right range for universal machine‑shop tasks With a measuring span of 0–300 mm, this instrument sits in the standard range for workshop metrology: a practical compromise between reach, stiffness and one‑handed operation. That range covers common depth‑measurement tasks on housings, bores and assemblies used in metalworking and general mechanical engineering, while preserving the rigidity required for consistent results. The compact spindle system and precise mechanics make it suitable for both bench inspection and setup work at the machine. Traceability, identification and system compatibility Identification data such as GTIN and the manufacturer SKU are available for asset management and inventory control, facilitating calibration scheduling and spare‑parts ordering. The instrument also supports quality documentation workflows through its factory calibration and clear specification set, which streamlines integration into existing inspection routines and reduces administrative overhead associated with measurement uncertainty reporting. Acquire the Microtech depth micrometer, factory‑calibrated to ISO 17025 with certificate, through Metav Werkzeuge — contact our Emmerich team at info@metav-werkzeuge.com or call +49 2822 7131930 for specification advice and ordering assistance Technical Data Article number: 110900305 GTIN: 4061905039904 Manufacturer: Microtech Metrology eCl@ss: 21170350 ETIM: EC003590 Facts Measuring range: 0–300 mm Resolution: 0.001 mm Accuracy: ±0.008 mm Protection rating: IP65 Special features Digital display with ON/ABS, SET, HOLD and mm/inch function Friction ratchet for reproducible measuring force Delivered with ISO 17025 calibration certificate Category: Messschrauben (micrometers) FAQ Is the instrument delivered calibrated? Yes. The depth micrometer is supplied fully calibrated to ISO 17025 and includes a calibration certificate for traceability. What resolution and accuracy can be expected? The gauge offers a resolution of 0.001 mm and an accuracy of ±0.008 mm, suitable for routine inspection and precise workshop measurement. Can the micrometer be used in workshop environments with coolant or dust? The unit is specified to IP65, providing protection against dust ingress and low‑pressure water jets common in machining environments. Which measuring tasks is this instrument best suited to? With a 0–300 mm range, the device is ideal for standard depth measurements on housings, bores and assemblies in machine shops and quality control. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
300mm Extension Rod Ø15.5mm For Rod Internal Micrometer Set, - Metav IndustryLine
Benefit from extended reach, secure fit and workshop-grade handling thanks to the 300 mm length and Ø 15.5 mm shank; ideal for extending the range of existing rod internal micrometre sets. Order the extension directly via Metav Werkzeuge or ask our consultants if needed. Extension rod 300 mm, Ø 15.5 mm for 310.064 — Metav IndustryLine accessory The Extension rod 300 mm, Ø 15.5 mm for 310.064 is a precision accessory that extends measurement reach for rod internal micrometre sets used in workshop inspection and fixture assembly. 300 mm extended reach for deep inspections Ø 15.5 mm shank for secure fitting Compatible with 310.064 internal micrometre set Solid 0.4 kg construction for stable measurements Reach deeper assemblies with reliable repeatability The extended 300 mm length provides decisive advantage when measuring recessed bores or deep internal features that standard probes cannot access. By increasing the effective reach without sacrificing stiffness, the extension rod preserves repeatability across multiple measurements. Compatibility with the referenced set ensures that the probe interface remains concentric and stable, reducing the need for repeated setups and saving inspection time. Secure connection and dimensional stability for consistent results The Ø 15.5 mm shank dimension guarantees a snug fit in the matching holder, allowing the extension to behave as a coherent part of the measuring chain rather than an add‑on. This mechanical fit promotes consistent axial alignment and minimises deflection during measurement. The moderate mass of 0.4 kg contributes to handling stability while remaining manageable in a typical shop environment, facilitating fast instrument changes and less operator fatigue. Practical use in workshop and quality inspection workflows Designed as an accessory for internal rod micrometres, the extension rod integrates seamlessly into existing measuring routines and fixtures. Its straightforward geometry makes it suitable for serial checks and incoming inspection where access depth is the limiting factor. The clear, compact form supports easy storage and rapid exchange between gauges, helping to maintain throughput on the shop floor without compromising measurement integrity. For extended reach in precision inspection, request the Metav IndustryLine 300 mm extension from Metav Werkzeuge; contact info@metav-werkzeuge.com or call +49 2822 7131930 for supply and technical advice Technical data SKU: M310.061.6 GTIN: 4054469118918 Manufacturer: Metav IndustryLine eClass: 21019104 ETIM: EC002219 Numbers / core technical data Length: 300 mm Diameter: 15.5 mm Weight: 0.4 kg Tariff code: 90173000 Compatibility / features Compatibility: for 310.064 internal micrometre set Category: Accessories (Measuring instruments accessory) Extension specification: 300 mm × Ø 15.5 mm Story trigger: zubehör FAQ What is the primary purpose of this extension rod? The extension rod is intended to increase the measurement reach of rod internal micrometre sets, enabling checks in deep bores and recessed features that the basic set cannot access. Will the extension fit other micrometre systems? Compatibility is specified for the matching holder of the 310.064 set; interchangeability with other brands or designs depends on matching the shank interface and seating geometry. How does the shank diameter affect measurement quality? A precise Ø 15.5 mm shank ensures secure engagement in the holder, which stabilises the measuring axis and reduces angular error, supporting repeatable internal measurements. Is the extension suitable for serial inspection tasks? Yes. The straight geometry and robust mass distribution make the extension well suited for repetitive inspection work where extended reach is required without frequent recalibration. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300mm Micrometer Caliper Set With Setting Gauges, Blue Powder Coated, Ratchet, Chrome-Plated Spindle - Metav IndustryLine
Combine comprehensive coverage with hardened measuring faces and a ratchet stop for reproducible results; the set's robust finish and included setting gauges ensure reliable workshop measurement. Order the micrometer set directly via Metav Werkzeuge or ask our consultants if needed. Micrometer set M304.429 — 0–300 mm workshop set with setting gauges, blue powder-coated frame (Metav IndustryLine) The Micrometer set M304.429 is a complete workshop set of analogue micrometers covering 0–300 mm, designed for routine inspection and reliable size checks in metalworking and mechanical workshops. Complete micrometer set 0–300 mm Blue powder-coated frame Ratchet stop for reproducible measuring Hardened measuring faces and matt-chromed drum Standard workshop range that covers everyday measurement needs This twelve-part micrometer set provides a continuous 0–300 mm measuring range, which places it squarely in the standard category for machine and metalworking shops. The configuration of gauges in 25 mm increments (from 25 mm to 275 mm) reduces the need to change instruments during common inspection tasks, saving time on routine checks. Conformity with DIN 863 ensures the set meets established dimensional metrology rules, making it suitable for quality control loops and delivery inspections where reproducible results are required. Consistent results achieved through controlled measuring force Repeatability is supported by the integrated ratchet stop, which limits variation caused by operator pressure, and by hardened measuring faces that maintain contact geometry under repeated use. The mechanical resolution of 0.01 mm on the analogue scale gives clear graduations for standard tolerances, while the 0.5 mm spindle pitch enables fine approach control. Together, these features reduce measurement scatter and make the set a reliable tool for batch inspections and process checks. Robust finish and ergonomic details for daily handling The frame is blue powder-coated to protect against workshop wear and handling, and the measuring drum is matt-chromed to reduce glare and improve long-term legibility. A substantial frame construction and a well-sized spindle (6.5 mm) contribute to stable feel and low torsion during measuring. These design choices translate into comfortable operation during repeated checks and less downtime for maintenance or recalibration, supporting steady throughput on the shopfloor. Complete set and secure transport for safe storage Delivered as a complete set, the micrometers arrive with setting gauges for quick verification of zero and interim checks. The instruments are supplied in a plastic or wooden case suited for transport, which protects sensitive faces and keeps the set organised when moved between benches or transported to inspection points. As an analogue, workshop-grade solution, the set blends straightforward operation with durable construction, making it a pragmatic choice for production environments. Secure this Metav IndustryLine micrometer set with Metav Werkzeuge in Emmerich for dependable workshop measurement and to discuss suitability for specific tasks via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M304.429 GTIN: 4054469117041 Manufacturer: Metav IndustryLine Norm: DIN 863 Category: Micrometers (analogue) Facts Measuring range: 0–300 mm Resolution / reading: 0.01 mm Spindle pitch: 0.5 mm Spindle diameter: 6.5 mm Pieces per set: 12 Weight: 17.0 kg Tariff number: 90173000 Special features Blue powder-coated frame Measuring drum matt-chromed Hardened measuring faces Ratchet stop for consistent measuring force Includes setting gauges in 25 mm increments (25–275 mm) Analogue micrometers, mechanical reading Delivered in a plastic or wooden case for transport FAQ What measuring range does the set cover? The micrometer set covers a continuous 0–300 mm range, supplied as a twelve-piece collection to span standard workshop requirements. How precise are the micrometers in the set? Each analogue instrument offers a standard reading of 0.01 mm with a spindle pitch of 0.5 mm; the ratchet stop helps ensure repeatable measuring force. Are the measuring faces durable for workshop use? Yes, the instruments feature hardened measuring faces designed to withstand repeated contact and preserve measurement geometry. Does the set include calibration or setting references? The set is supplied with setting gauges (25 mm increments from 25 mm to 275 mm) for quick verification and adjustment during routine checks. Is this set suitable for regular production inspection? Designed to meet DIN 863, the set is intended for workshop and inspection tasks where robust construction and reproducible results are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300mm Micrometer Holder Adjustable Tilt, 2 kg Capacity - Metav IndustryLine
The combination of an adjustable tilt angle, compatibility with micrometers up to 300 mm and a solid 2 kg load capacity delivers steady, repeatable support for bench metrology; order the micrometer holder directly via Metav Werkzeuge or contact our consultants for tailored advice. M304.006 Micrometer holder — adjustable tilt, for micrometers up to 300 mm (Metav IndustryLine) A compact, workshop-ready micrometer holder, the M304.006 secures micrometers up to 300 mm and offers an adjustable tilt angle to aid precise alignment in routine measurement tasks. Adjustable tilt for precise alignment Suitable for micrometers up to 300 mm 2 kg capacity for common micrometers Robust 2.3 kg construction for steady support Reduced alignment error through adjustable tilt The holder's adjustable tilt lets the measuring axis be aligned more precisely with the workpiece, which supports repeatable alignment during serial checks. By permitting small angular corrections, the fixture reduces the need to reorient the instrument or the part between measurements; this saves handling time and minimises variability caused by inconsistent seating. The tilt mechanism is also useful when measuring on irregular surfaces where a perpendicular approach is impractical, so measurement routines remain efficient without compromising consistency. Compatibility with standard workshop micrometers for seamless workflow Designed as an accessory for bench metrology, the unit accepts micrometers up to 300 mm, covering the standard and extended ranges used in machine shops and toolrooms. The 2 kg capacity accommodates most heavy-duty micrometers while keeping the instrument stable during use. This compatibility means fewer changeovers and a more rationalised toolset: one dedicated holder replaces improvised supports, shortening set-up times and helping to maintain throughput in repetitive inspection tasks. Stable support that improves reading reliability At approximately 2.3 kg, the holder provides a low centre of gravity that helps dampen small disturbances during measurement, delivering steady support for fine readings. The fixture is an accessory intended to integrate into existing benches and inspection stations, improving ergonomics by holding the micrometer in a fixed, repeatable position. For users focused on process reliability, the device reduces operator-induced variation and contributes to tighter control of measurement sequences without introducing complex handling steps. Contact Metav Werkzeuge today to discuss how the M304.006 micrometer holder can be integrated into existing inspection setups or to arrange a quotation and delivery from our Emmerich facility. Technical data Article number: M304.006 GTIN: 4054469115849 ECLASS: 21029090 Harmonised tariff number: 90173000 Manufacturer: Metav IndustryLine Numbers / Core technical data Maximum micrometer size: 300 mm Load capacity: 2 kg Product weight: 2.3 kg Design / Special features Adjustable tilt angle For micrometers up to 300 mm Accessory for bench metrology FAQ Which micrometer sizes are compatible with this holder? The holder accepts micrometers up to 300 mm and is designed for standard workshop and inspection use with devices in that size range. Can the tilt be fixed at set angles for repeat inspections? Yes, the adjustable tilt mechanism is designed to be set and held in position, enabling repeatable alignment for serial measurements. What is the load capacity of the fixture? The unit has a load capacity of 2 kg, suitable for most heavy-duty micrometers without compromising stability. Does the holder improve measurement repeatability? By keeping the measuring axis stable and allowing precise angular adjustment, the holder reduces handling variation and improves repeatability in bench measurements. Is the M304.006 suitable for industrial inspection stations? Yes, the M304.006 is intended as a workshop accessory to integrate into inspection stations where micrometers up to 300 mm are used. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
300mm Micrometer With 35mm Measuring Faces, 1.54" Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of ISO 17025 traceable calibration and fast digital data transfer to secure reproducible results and streamlined inspection workflows; order via Metav Werkzeuge or consult our specialists for integration and configuration advice. Digital Micrometer 275–300 mm by Microtech Metrology — Touchscreen readout, Wireless + USB The Digital Micrometer 275–300 mm is an industrial outside micrometer designed for standard workshop and inspection tasks, combining large Ø35 mm disc measuring faces with a compact digital interface for repeatable contact on medium-sized components. ISO 17025 calibration certificate included Wireless & USB data output 1.54-inch touchscreen readout Accuracy 0.008 mm Certified precision for reliable process control This digital measuring instrument delivers traceable calibration under ISO 17025, supplied with a calibration certificate that documents conformity and supports quality audits. The stated accuracy 0.008 mm and high display resolution make the tool suitable for standard metrology tasks where reproducibility is required. Classified within the Standard measuring range (up to 300 mm), the device balances reach and stiffness, making it well suited to general machine‑shop and metalworking inspection where consistent results form the basis for process decisions. Seamless digital capture to speed inspection cycles Equipped with a 1.54‑inch touchscreen and Wireless + USB data output, the micrometer simplifies transfer of results into spreadsheets or SPC systems, reducing transcription errors and saving operator time. The combination of wireless connectivity and a wired USB option enables flexible integration with existing data‑collection workflows. A non‑rotating spindle improves repeatability during contact, supporting quicker successive readings without operator‑induced variation — a practical efficiency gain for batch inspections and setup checks. Stable measuring faces and ergonomic handling for everyday use Large Ø35 mm disc measuring faces provide a broader contact area that helps accommodate slightly rough or curved surfaces while maintaining alignment, reducing rocking and improving measurement stability. The instrument’s measuring range (275–300 mm) covers larger standard parts such as housings, flanges and medium-sized fixtures without sacrificing manoeuvrability. Delivered calibrated to ISO 17025, the micrometer arrives ready for use in production and quality environments, ensuring that documentation requirements and traceability are covered from the first measurement. For traceable, production‑ready measuring capability and support with data integration, contact Metav Werkzeuge in Emmerich — Metav Werkzeuge GmbH can advise on the Microtech digital micrometer (SKU 110783007) and assist with ordering or technical questions at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 110783007 GTIN: 4061905457555 Manufacturer: Microtech Metrology eClass: 21170328 ETIM: EC003590 Numbers / Core technical data Measuring range: 275–300 mm Measuring range (max): 300 mm Measuring range (min): 275 mm Accuracy: 0.008 mm Resolution (display): 0.0001 mm Display: Touchscreen 1.54" Data output: Wireless + USB Digital device: yes Calibration: ISO 17025 certificate included Designs / Special features Disc measuring faces Ø35 mm Non‑rotating spindle Digital touchscreen readout Wireless and USB connectivity Supplied with ISO 17025 calibration certificate FAQ Is the micrometer supplied with a calibration certificate? Yes. The micrometer is delivered fully calibrated and includes an ISO 17025 calibration certificate documenting traceability. Which data interfaces are available for measurement transfer? Measurements can be transmitted via Wireless connection or through USB, allowing integration with data collection systems and SPC workflows. What measurement range does this instrument cover and how is it classified? The device measures from 275 to 300 mm and falls within the Standard category for calipers and micrometres (up to 300 mm), offering a balance of reach and rigidity for workshop use. How precise is the digital readout? The digital readout provides a resolution of 0.0001 mm with an instrument accuracy of 0.008 mm, suitable for standard quality‑control and inspection tasks. Are the measuring faces suitable for curved or uneven surfaces? Yes. The Ø35 mm disc measuring faces offer a broader contact area that helps maintain stable contact on slightly curved or uneven surfaces. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
300mm Outside Micrometer Set Ratchet Stop, Calibration Certificate ISO17025 - Microtech Metrology
Take advantage of traceable measurement, reliable repeatability and a complete workshop range in one set; the combination of ISO 17025 calibration, a ratchet stop and a 0–300 mm coverage ensures consistent production control. Order the set directly via Metav Werkzeuge or ask the consultants for application advice. Micrometer set — Outside micrometers, 0–300 mm range, ratchet stop (Microtech Metrology) The Micrometer set is a calibrated set of outside micrometers for precise external measurements in workshop and laboratory environments. ISO 17025 calibration certificate included Ratchet stop for consistent measuring force Range 0–300 mm across 12 sizes High-accuracy outside micrometer heads Traceable precision for quality control The set delivers traceable measurement through an ISO 17025 calibration certificate, which documents the performance of each gauge and supports quality assurance procedures. With a typical readout of 0.01 mm, the analogue micrometer heads provide industrial-grade resolution suitable for process control and incoming inspection. The presence of a ratchet stop reduces operator-induced variation by standardising the measuring force, translating to fewer rechecks and more reliable batch acceptance rates. Built for repeatability and workshop efficiency Designed as a comprehensive 12-piece set covering 0–300 mm, the collection replaces the need to switch between scattered instruments, reducing downtime during setup. Each head is finished for durability and consistent contact geometry, while the ratchet stop ensures repeatable contact pressure across operators. The practical layout and calibrated delivery allow rapid integration into metrology routines, improving throughput and lowering the risk of non-conforming parts due to measurement error. Practical application and handling benefits The micrometers are intended for external measurements on shafts, pins and machined features where high repeatability matters. The anvil diameter of Ø 6.5 mm gives a defined contact area that is particularly useful on small-diameter features, while the analogue mechanism offers tactile feedback preferred in many workshop environments. Supplied as a set of twelve sizes, the range covers most common tasks in machining, maintenance and quality departments, enabling technicians to maintain process accuracy without frequent tool changes. Proven partners for dependable supplies Microtech Metrology provides the measuring technology in this set, while Metav stands for democratisation of precision across workshops and industry. With a broad product range and an established distribution hub in Emmerich, Metav ensures rapid availability and consistent quality control upstream of delivery. The included ISO 17025 calibration certificate and the set configuration support compliance needs for manufacturing, certification and traceability, helping to secure audit trails and supplier confidence. Choose the traceable precision of the Microtech Metrology micrometer set — contact Metav Werkzeuge for a tailored quotation and technical advice Technical data Article number: 110110311 GTIN: 4061905458934 Manufacturer: Microtech Metrology Range: 0–300 mm Pieces per set: 12 Calibration: ISO 17025 certificate included Facts Resolution: 0.01 mm Anvil diameter: Ø 6.5 mm Readout type: analogue Ratchet stop: yes Special features Outside micrometers for external measurements Ratchet stop for consistent measuring force High-accuracy micrometer heads Supplied as a complete 12-piece set FAQ What level of accuracy does this micrometer set provide? The micrometer set from Microtech Metrology delivers industrial-grade resolution of 0.01 mm and is supplied with an ISO 17025 calibration certificate confirming laboratory-traceable accuracy. Is the measuring force standardised to avoid operator variation? Yes—the micrometers feature a ratchet stop that standardises contact pressure, improving repeatability across operators when using the Microtech Metrology outside micrometer set (SKU 110110311). Does the set cover common workshop requirements for external measurements? The 12-piece range spanning 0–300 mm covers the typical measuring needs of machine shops, maintenance departments and quality control stations, eliminating frequent instrument changes. Are the micrometers ready for use upon delivery? Each instrument in the set is delivered calibrated and accompanied by an ISO 17025 certificate, enabling immediate integration into controlled measurement processes. What contact area is provided for small features? The micrometer anvils have a diameter of Ø 6.5 mm, providing a defined contact surface that is suitable for many small-diameter shafts and machined features. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
300mm Repair Set For Micrometer Anvil With Two Spacers - Metav IndustryLine
Reduce downtime and restore reliable measurement geometry with a robust replacement anvil and two distance sleeves (25 mm and 50 mm) designed for large‑range outside micrometres; precision fit and durable construction help maintain inspection throughput. Order the repair set directly via Metav Werkzeuge or ask our consultants if needed. Repair set M304.033.2 for large‑range outside micrometres — Anvil + 25 mm & 50 mm distance sleeves (Metav IndustryLine) The Repair set M304.033.2 provides a hardened replacement anvil and two distance sleeves for outside micrometres with extended measuring ranges, intended for workshop and inspection use Replacement anvil for large-range micrometres Includes 25 mm and 50 mm distance sleeves Precision fit to restore measurement geometry Suitable for micrometres with 300–1000 mm range Restore measurement geometry quickly and reliably A worn or damaged anvil distorts contact geometry and compromises repeatability; the supplied replacement restores the original seating and contact plane so measurements return to specification. The two distance sleeves (25 mm and 50 mm) enable straightforward adaptation to different spindle positions without complex shimming, reducing repair time. Designed for practical workshop use, this kit re-establishes the correct mechanical interface between spindle and anvil, which is the fundamental prerequisite for reproducible external diameter measurements on large components. Built for medium and large‑range micrometres used in production This accessory set is intended for outside micrometres covering the 300–1000 mm measuring band, bridging mid‑sized and large‑format inspection tasks. The components are suited to long‑format instruments where profile stiffness and correct contact geometry are essential for reproducible results across the full travel. By matching the original contact geometry, the kit supports consistent measurement behaviour on parts such as large housings, shafts and fixtures, making it a practical choice for machine shops, toolroom inspection benches and fixture maintenance. Practical benefits: fit, durability and ease of replacement Components are manufactured with workshop durability in mind and finished to ensure a close, repeatable fit with the instrument body. The set is compact and straightforward to handle — the complete kit has a nominal weight of about 1 kg — so replacement can be completed with common bench tools, avoiding extended downtime. Restoring the correct anvil seating reduces the need for corrective rework and helps maintain traceable measurement routines; when combined with a final verification step on a calibration standard, overall measurement reliability is recovered efficiently. Contact Metav Werkzeuge for availability of the Metav IndustryLine M304.033.2 repair set and expert advice on restoring measuring capability without delay Technical data Article number: M304.033.2 GTIN: 4054469115924 SKU: M304.033.2 Tariff code: 90173000 Weight: 1 kg Numbers / Core technical data Measuring range suitability: 300–1000 mm Distance sleeves: 25 mm, 50 mm Special features / Versions Replacement measurement anvil included Two distance sleeves for spindle adaptation Accessory for outside micrometres Category: Accessories for measuring instruments FAQ How does this repair set restore micrometre accuracy? Replacing a worn anvil with the matched anvil in the M304.033.2 kit reinstates the correct contact geometry and seating, which improves repeatability and reduces systematic deviation during external measurements. Which instruments are compatible with the set? The set is compatible with outside micrometres and similar spindle‑and‑anvil instruments specified for the 300–1000 mm measuring band; it is intended as an accessory for large‑range instruments. What exactly is included in the kit? The repair set contains one replacement measurement anvil and two distance sleeves sized 25 mm and 50 mm, delivered as a single accessory package under SKU M304.033.2. Is a calibration certificate supplied with the components? The kit restores the mechanical interface; a final calibration or verification on appropriate reference standards is recommended after fitting to confirm conformity with the instrument’s tolerance specifications. Can the sleeves be used to adapt different spindle positions? Yes, the 25 mm and 50 mm distance sleeves allow straightforward adaptation of the anvil position to match different spindle extensions, reducing the need for additional adjustment work. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Precision micrometers built for repeatable accuracy
Micrometers—also referred to as micrometer screw gauges or micrometer callipers—are compact, robust instruments for fast, highly accurate length measurement of small to medium workpieces. Designed for routine use on the shop floor, these tools combine mechanical reliability with options for digital data capture, making them indispensable where repeatable tolerances matter.
How micrometers work and where they belong in production
Micrometers operate on a finely threaded spindle that brings two measuring faces into alignment with the workpiece; many designs follow the Abbe comparator principle so that the measuring axis and scale are collinear, reducing tilting errors. Typical outside micrometers (bühlermessschrauben) provide readings down to 1/1000 mm (0.001 mm) in analogue form; internal micrometers and specialised two- or three-point gauges enable accurate diameter and bore measurements, while depth micrometers cover depths from 0–300 mm. Hardened carbide (HM) measuring faces are standard to prevent wear and maintain accuracy over time. Digital variants offer easy reading, unit switching (mm/inch) and data output via USB, RS interface or Bluetooth; advanced models with an integrated minicomputer support Go/NoGo checks, temperature compensation and wireless transmission up to 50 m.
Practical benefits that improve shop‑floor performance
- Reduced rework and higher first-pass yield thanks to repeatable accuracy and carbide-tipped measuring faces.
- Faster, safer measurement cycles by using the ratchet/coupling to limit measuring force to 5 N to 10 N, protecting both part and instrument.
- Flexible inspection workflows with analogue, digital and minicomputer options, including wireless data transfer and mm/inch toggle.
- Versatile coverage with outside, internal, depth and built-in micrometers offering measuring ranges from a few millimetres up to 300 mm and resolution down to 2 µm (internal) or 0.003 mm (standard depth micrometers).
- Durable operation in workshop environments: mechanical models resist dust and moisture, while digital versions are available with IP54 protection.
Metav — a precision partner you can rely on
Metav combines decades of technical expertise with a broad, quality-filtered product range from its Emmerich hub. Over 48,000 customers trust Metav’s offer of more than 250,000 products, which simplifies procurement and secures reliable supply for industry, trade and specialist retailers. For buyers seeking micrometers with consistent performance and traceable data capture, Metav’s selection and technical support make it a practical, long-term choice.
In short
Micrometers provide robust, highly repeatable measurement for external, internal and depth applications, available in analogue, digital and minicomputer formats to match precision requirements and data‑management needs.
FAQ
How precise are micrometers for internal measurements?
Internal micrometers in the micrometers category can achieve accuracies around 2 µm when correctly used; digital and minicomputer models improve readout convenience and data integration for traceable inspection results.
When is a digital micrometer preferable to an analogue one?
Choose a digital micrometer when easy readout, unit conversion (mm/inch), or data transmission is required. Digital models with IP54 rating also offer dust and splash protection, while analogue micrometers remain the most robust option in harsh environments.
What measuring force should be used to ensure consistent results?
The recommended measuring force for micrometers is 5 N to 10 N. Use the ratchet or friction thimble to apply this consistent force and rely on the insulating sleeve to minimise heat transfer from the hand.
Can depth micrometers measure small bores and tight features?
Yes. Depth micrometers use a fine needle or flat measuring face and, with suitable extensions, cover narrow or deep features; standard depth micrometers typically span 0–300 mm with accuracies near 0.003 mm, while specialised digital systems offer even higher resolution.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com