Precision micrometers for reliable dimensional control
Micrometers deliver precise length and depth measurements in metalworking, enabling repeatable control over component tolerances and process stability. These instruments—available as outside micrometers, inside micrometers and depth micrometers—offer hardened contact faces and fine-thread spindles to ensure long-term accuracy and resistance to wear, with digital versions providing data transfer via USB or Bluetooth for seamless integration into inspection software. Typical uses include measuring small bores, depths and diameters in precision engineering, where features must be defined to micrometre-level accuracy; features such as ratchet thimbles and insulated frames help maintain consistent measuring force and temperature compensation. Choose between robust analog models, IP54-protected digital micrometers or micrometers with an integrated minicomputer for advanced functions like unit conversion, temperature correction and Go/NoGo evaluations.
75-100mm Precision Micrometer Digital IP65, Ø12mm Measuring Faces - Microtech Metrology
Take advantage of the combination of a digital readout with 0.001 mm resolution, robust IP65 protection and a 0.006 mm accuracy for repeatable internal measurements; order via Metav Werkzeuge or consult the Metav team for application advice. Digital internal micrometer (75–100 mm) by Microtech Metrology The Digital internal micrometer is a precision instrument for measuring internal diameters in fine mechanical and workshop environments, covering the 75–100 mm range with a protected electronic display. *Digital readout with 0.001 mm resolution *IP65 dust and splash protection *Measuring range 75–100 mm for internal diameters *Ø12 mm hardened measuring faces Reliable measurements in demanding workshop conditions The instrument combines a protected IP65 housing with a finely tuned drive mechanism to deliver consistent results even where coolant mist or workplace dust is present. With an indicated accuracy of 0.006 mm and a display resolution of 0.001 mm, the device reduces reading uncertainty and speeds up inspection routines. The sealed electronics preserve display reliability and extend service intervals, which supports continuous production checks without frequent interruptions. Optimised for small to medium internal bores With a measuring span of 75–100 mm, this tool is classified in the micro range and is particularly suited to compact components and precise internal diameters encountered in watchmaking, valve seats and bearing housings. The Ø12 mm measuring faces provide a stable contact area for repeatable seating in bores, improving concentric measurement stability. This combination of range and contact geometry balances reach with stiffness, making it straightforward to obtain reproducible results on small assemblies. Clear digital handling for efficient quality control The electronic readout delivers a prompt numeric result, eliminating parallax errors common to purely mechanical gauges. The digital display with 0.001 mm steps facilitates quick sorting decisions on the shop floor and reduces documentation time during batch inspections. Together with the micrometer’s robust ingress protection, the readout supports reliable use in production, incoming inspection and maintenance settings where fast, unequivocal measurements are required. Practical applications and workshop integration Typical applications include bore gauging, internal diameter checks on assemblies and pass/fail inspections in small-to-medium sized components. The device’s construction and accuracy make it a pragmatic choice for laboratories and machine shops seeking a compact measuring tool that fits established inspection fixtures without the overhead of specialised bench equipment. Integration into existing workflows is straightforward because the unit provides direct numeric feedback and a measurement range that covers many common internal tolerances. For tailored advice or to purchase the Microtech Metrology digital internal micrometer, please contact Metav Werkzeuge in Emmerich by phone on +49 2822 7131930 or by e‑mail at info@metav-werkzeuge.com — the Metav team will help confirm suitability and delivery options. Technical Data SKU: 133801001 GTIN: 4061905458125 eClass: 21170328 Manufacturer: Microtech Metrology Facts Measuring range: 75–100 mm Accuracy: 0.006 mm Resolution / display: 0.001 mm Protection class: IP65 Measuring faces diameter: Ø12 mm Design & Features Digital internal micrometer Category: Micrometers (internal) Electronic display Robust ingress protection for shop use FAQ What measurement range does this instrument cover? The digital internal micrometer covers a measuring range of 75–100 mm, suitable for compact internal diameters and micro‑range inspection tasks. What accuracy and resolution can be expected? The instrument offers an accuracy of 0.006 mm and a display resolution of 0.001 mm, providing fine graduation for precise internal measurements. Is the device suitable for use in damp or dusty environments? Yes, the device is rated IP65, which provides protection against dust ingress and low‑pressure water jets, making it suitable for many workshop conditions. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-100mm Precision Micrometer With Colour Touchscreen, Wireless USB, IP65 - Microtech Metrology
Benefit from high-precision measurement, robust ingress protection and seamless data transfer for efficient quality control. Combine the accuracy 0.004 mm, Wireless + USB output and IP65 sealing for reliable on‑site and lab use. Order directly via Metav Werkzeuge or consult our specialists for integration advice. Microtech Micrometer — digital micrometer, 75–100 mm, IP65, 2.4" touchscreen The Microtech Micrometer is a digitally measured micrometer designed for precise workshop and laboratory measurements across a 75–100 mm range. High precision ±0.004 mm accuracy Integrated Wireless + USB output Robust IP65 protection Colour 2.4" touchscreen display Precision where repeatability counts The instrument delivers substantial measurement reliability thanks to its accuracy 0.004 mm and high-resolution reading of 0.0001 mm, which together reduce uncertainty in routine inspection tasks. This level of precision supports repeatable results when checking components with tight tolerances and enables confident go/no-go decisions in production. The solid measuring faces (Ø12 mm) maintain consistent contact geometry for each reading, limiting variability introduced by changing contact conditions. Seamless data capture for process control Equipped with Wireless + USB outputs and a clear 2.4" touchscreen, the device simplifies data logging and process documentation. Measurements can be transmitted directly to inspection software or a laptop for traceable records, reducing transcription errors and speeding up reporting. Integration into existing quality workflows is straightforward, making the instrument suitable for traceable inspection routines and batch control where documented evidence is required. Built for workshop durability and continuous use The unit’s IP65 rating protects the electronics against dust and water jets, which extends operational life in harsher workshop environments. The robust construction means fewer interruptions for maintenance and reliable performance on the shop floor. The digital electronics and sealed enclosure also contribute to lower service frequency compared with purely analogue instruments, promoting sustained availability for production-critical measurement tasks. Practical handling and measurement versatility Operating ergonomics are tuned for regular use: the digital display is legible and responsive, and the compact form factor supports comfortable one‑hand measurement across the measurement range 75–100 mm. The instrument’s measuring faces of Ø12 mm give a stable contact area for consistent pressure distribution. As a digitally driven micrometer, it reduces operator influence on readout interpretation and helps maintain throughput during repetitive inspection cycles. For detailed technical advice on the Microtech Micrometer or to discuss integration into an existing inspection line, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants provide specification guidance and delivery options tailored to professional requirements. Technical data Article number: 133801008 GTIN: 4061905457982 Manufacturer: Microtech Metrology Facts Measurement range: 75–100 mm Accuracy: 0.004 mm Reading: 0.0001 mm Display: Colour 2.4" touchscreen Protection class: IP65 Special features Data output: Wireless + USB Measuring faces: Ø12 mm Instrument type: Digital micrometer Digital: yes FAQ What measurement range does this micrometer cover? The micrometer covers a 75–100 mm range, suitable for medium‑sized component checks and workshop inspection tasks. How accurate is the instrument for inspection work? With an accuracy of 0.004 mm and a reading step of 0.0001 mm, the instrument meets the demands of precision quality control in production and lab environments. Can measurement data be exported directly to inspection software? Yes, the device offers Wireless + USB outputs for direct data transfer to PCs or data loggers, facilitating digital record keeping. Is the micrometer suitable for harsh workshop conditions? The IP65 rating provides dust and water‑jet protection, making the instrument durable for routine shop‑floor use. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-100mm Thread Micrometer Digital Colour 2.4" Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of precise thread inspection, modern data transfer and certified calibration to streamline quality control and record-keeping; the combination of high resolution, a non‑rotating spindle and ISO 17025 calibration ensures reproducible results and traceable documentation. Order the thread micrometer directly via Metav Werkzeuge or ask our consultants if needed. Thread micrometer Whitworth 55 — Microtech Metrology, Colour 2.4" touchscreen & Wireless+USB The thread micrometer Whitworth 55 is a compact, workshop-ready instrument for accurate measurement of Whitworth threads between 75 and 100 mm, designed for calibrated quality control in production and inspection environments ISO 17025 calibration included certificate Colour 2.4" touchscreen display Wireless and USB data output High precision: 0.004 mm accuracy Accurate thread control for repeatable results This instrument delivers a measurable advantage where repeatability matters: the non‑rotating spindle minimises disturbance to threaded profiles, reducing measurement scatter on delicate Whitworth threads. With a stated accuracy of 0.004 mm and a readout resolution of 0.0001 mm, the device suits fine inspection tasks in the compact "Micro" class (measurement range up to 100 mm), where stiffness and handling are balanced for small to medium components. The robust mechanical concept combined with the electronic readout supports reliable process control and fewer reworks in small-batch production. Fast digital capture to simplify quality workflows Equipped with a Colour 2.4" touchscreen and dual data interfaces, the instrument speeds the transfer of measurement records into a laboratory database or a shop‑floor logging system. Wireless transfer and USB connectivity reduce manual transcription errors and allow secure archiving of results for traceability. The clear touch display shortens operator training time and enables rapid checks during set‑up or final inspection. As a result, inspection routines become both faster and more transparent — an advantage for busy quality teams seeking to tighten tolerances without adding complexity. Calibrated delivery and thread‑specific accessories The micrometer is supplied fully calibrated to ISO 17025 with an accompanying calibration certificate, allowing immediate use in accredited quality procedures and audit trails. Delivery includes 10x anvils 60‑3.5 TPI (Whitworth 55), which match the Whitworth standard and remove the need for immediate additional tooling. The instrument’s configuration is therefore suitable for workshop use and for integration into formal inspection plans where documented measurement capability is required. For precision purchases aligned with industrial standards, contact Metav Werkzeuge for tailored advice and fast delivery from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 110721008 GTIN: 4061905457265 Manufacturer: Microtech Metrology Type: Whitworth 55 Measurement range: 75–100 mm Accuracy: ±0.004 mm Numbers / Core technical data Readout resolution: 0.0001 mm Measurement range min: 75 mm Measurement range max: 100 mm Special features Colour 2.4" touchscreen display Wireless + USB data output Non‑rotating spindle (prevents thread damage) Digital instrument (electronic readout) Delivered with 10x anvils 60‑3.5 TPI (Whitworth 55) Supplied calibrated to ISO 17025 with certificate FAQ How precise is the instrument for thread inspection? The thread micrometer delivers an accuracy of ±0.004 mm and a readout resolution of 0.0001 mm, suitable for fine inspection of Whitworth threads in production and quality control. Is a calibration certificate supplied with the micrometer? Yes — the instrument is supplied fully calibrated to ISO 17025 and includes the corresponding calibration certificate for traceable measurement records. Which data interfaces are available for documentation? Data transfer is possible via Wireless and USB interfaces to support digital logging and simplified transfer into inspection software. Are specific anvils included for Whitworth threads? The delivery includes 10x anvils 60‑3.5 TPI matched to Whitworth 55, enabling immediate use for the intended thread form without additional accessories. What advantages does the non‑rotating spindle offer? The non‑rotating spindle reduces damage and measurement variability on threaded profiles, improving repeatability when assessing thread parameters. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-100mm Tolerance Bore Micrometer Digital Fine-Indicator, IP54, Delivered In Case - Filetta
Benefit from ±0.005 mm accuracy, 0.001 mm resolution and robust IP54 protection for reproducible shop‑floor measurements; order the tolerance micrometer directly via Metav Werkzeuge or consult our specialists for application advice. Tolerance Micrometer MS910.505 — digital fine indicator, IP54, rechargeable The Tolerance Micrometer MS910.505 is a precision micrometer designed for accurate tolerance checks in workshop and inspection environments, offering a fine digital readout with mm/inch selection and splash protection. IP54 protection for workshop conditions Accuracy ±0.005 mm for reliable tolerances Rechargeable lithium battery with mm/inch display Supplied with adjustment standard and digital fine indicator Precision where it counts: reliable tolerance control The compact instrument delivers a resolution of 0.001 mm and an accuracy of ±0.005 mm, providing traceable results for routine quality checks and first‑article inspections. The small, hardened measuring faces with a diameter of Ø6.5 mm concentrate contact force into a stable, repeatable point; combined with a specified measuring force of 5–10 N, this reduces variability from operator pressure and supports consistent pass/fail decisions. The digital readout with mm/inch selection simplifies documentation and reduces transcription errors during batch testing. Built for robust use on the shop floor With an IP54 protection rating the device tolerates dust ingress and splashing fluids typical in metalworking and general workshop conditions, while the rechargeable lithium battery keeps downtime low and avoids frequent battery changes. The electronic display incorporates an on/off switch and straightforward zeroing, enabling fast set‑up and quick transitions between inspection tasks. An adjustment standard is included, facilitating simple verification of zero and aiding routine traceability without immediate external calibration. Compact measuring range matched to fine mechanical work The measuring range of 75–100 mm places this micrometer in the compact class ideal for fine mechanical assemblies and precision components where stiffness and handling are crucial. Such a range gives a practical balance between reach and rigidity, making it suitable for small assemblies, toolroom tasks and fine adjustment work in fixtures. The instrument’s form factor supports safe, single‑hand operation while maintaining the stability needed for micrometre‑level results. Faster measurement routines and integration into QA workflows The digital fine indicator speeds up repetitive measurement tasks and reduces operator fatigue compared with prolonged analogue reading. Clear numeric output and mm/inch switching streamline data capture for quality records and short measurement cycles, supporting higher throughput without sacrificing accuracy. The combination of compact design, high resolution and robust protection makes this micrometer a practical addition to manufacturing lines, inspection benches and maintenance toolkits. For precise, workshop‑ready measurements from Filetta, contact Metav Werkzeuge for product selection and procurement: info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will advise on the best configuration for specific applications. Technical data Article number: MS910.505 Name: Tolerance micrometer, digital fine indicator Manufacturer: Filetta Protection class: IP54 Measurements Measuring range: 75–100 mm Resolution: 0.001 mm Accuracy: ±0.005 mm Measuring faces: Ø6.5 mm Measuring force: 5–10 N Display: mm/inch, on/off Battery: Lithium, rechargeable Adjustment standard: included Special features Digital fine indicator for fast readings Robust IP54 protection for workshop use Rechargeable power source reduces downtime Supplied adjustment gauge for verification FAQ What measuring range does this micrometer cover? The micrometer covers a range from 75 to 100 mm, making it suitable for compact precision tasks and small assemblies. What resolution and accuracy can be expected from the device? The digital fine indicator provides a resolution of 0.001 mm with an accuracy of ±0.005 mm for repeatable tolerance checks. Is the instrument protected against workplace contamination? Yes, the instrument has an IP54 rating, offering protection against dust ingress and water splashes typical of workshop environments. Does the micrometer include any calibration or verification aid? An adjustment standard is supplied with the micrometer to allow immediate verification and simpler routine checks. What power source does the display use? The unit uses a rechargeable lithium battery and features an on/off control and mm/inch switching on the digital display. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
75-100mm Tube Wall Thickness Micrometer Colour Touchscreen, IP65, ISO17025 Calibration - Microtech Metrology
Take advantage of highly reproducible measurements thanks to an ISO 17025 calibration certificate and a fine 0.003 mm measurement accuracy, together with flexible Wireless and USB data transfer for seamless integration into digital workflows; order the calibrated instrument directly via Metav Werkzeuge or consult our specialists for application advice. Tube Wall Thickness Micrometer — microcomputer-controlled micrometer with Wireless+USB and 2.4" touchscreen by Microtech Metrology Tube wall thickness micrometer with a microcomputer for precise measurement of tube and pipe wall thicknesses in production and quality control environments *ISO 17025 calibration certificate included *0.003 mm measurement accuracy *Wireless and USB data output compatible with HID protocols Measurement precision that protects product quality The instrument combines a 0.003 mm stated accuracy with a high-resolution readout, delivering reproducible results for thin-walled components. Supplied with an ISO 17025 calibration certificate, the device meets traceability requirements for production control and inspection records. The calibration certificate documents compliance with recognised standards and simplifies incorporation into quality management systems. Such metrological reliability reduces scrap rates and supports consistent process control in serial production. Streamlined data capture for modern production lines Equipped with Wireless and USB data outputs and a 2.4" colour touchscreen, the micrometer transfers measurements directly to Windows, Android, iOS, macOS or Linux systems using standard HID protocols. The combination of wireless long-range transmission and USB HID ensures fast, error-free data logging and easy integration with SPC or MES solutions. A built-in microcomputer processes readings before transfer, reducing manual transcription and accelerating reporting cycles for quality teams. Robust design for everyday workshop and laboratory use Engineered for routine inspection tasks, the instrument features an IP65 rating, a friction ratchet for reproducible contact force and a rotating spindle for smooth operation. Classified as a micro-range instrument (measurement span 75–100 mm), it is compact enough for fine-mechanical work yet offers reach for larger tubular components. The tool is suitable for measuring tube wall thicknesses from 4.7 mm upwards and its protective ingress rating supports usage in workshop environments where coolant mist or dust may be present. Practical fit for production and research applications This micrometer bridges laboratory accuracy and shop-floor usability: the calibrated measuring system supports audit-ready documentation while the ergonomic controls and ratchet mechanism promote repeatable handling during high-throughput checks. Integration-ready data outputs and the touchscreen reduce cycle time for logged measurements, supporting lean inspection routines. For operations seeking dependable, calibrated measurements from a single supplier, the instrument delivers metrological rigour and straightforward digital workflow compatibility. Contact Metav Werkzeuge today to specify the correct Microtech Metrology tube wall thickness micrometer for the intended application and arrange delivery of the ISO 17025‑calibrated unit directly from our Emmerich hub Technical Data Article number: 110351008 GTIN: 4061905040870 Manufacturer: Microtech Metrology Facts Measurement range: 75–100 mm Measurement accuracy: 0.003 mm Display/readout resolution: 0.0001 mm Display size: 2.4" touchscreen Protection rating: IP 65 Special features ISO 17025 calibration certificate included Wireless + USB data output (HID compatible) Colour 2.4" touchscreen Friction ratchet for constant measuring force Rotating spindle for smooth adjustment Suitable for tube wall thickness from 4.7 mm Computerised micrometer electronics with long-range wireless option FAQ Is the micrometer supplied with a calibration certificate? Yes. The micrometer is delivered fully calibrated with an ISO 17025 calibration certificate, documenting traceability and measurement conformity. Which data interfaces are supported for direct logging? Measurements are output via Wireless and USB using HID protocols, allowing direct transfer from the Microtech micrometer to Windows, Android, iOS, macOS or Linux systems. What is the usable measurement range and typical application? The device covers a measurement span of 75–100 mm and is intended for tube wall thickness checks, able to measure wall thicknesses from 4.7 mm upwards. How does the instrument perform in workshop conditions? With an IP65 rating, a friction ratchet and a rotating spindle, the micrometer is designed for robust shop‑floor use while maintaining repeatable contact force and reliable readings. Can this instrument be integrated into a quality management workflow? Yes. The calibrated readings, USB/Wireless outputs and digital readout make the instrument suitable for SPC and MES integration and for generating audit-ready measurement records (SKU 110351008). Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-100mm Tube Wall Thickness Micrometer Digital IP65, Friction Thimble, ISO 17025 Calibration Certificate - Microtech Metrology
The high-accuracy digital micrometer combines IP65 protection, a 0.003 mm accuracy specification and an ISO 17025 calibration certificate to deliver reliable, traceable tube wall measurements on the shop floor; its friction thimble and rotating spindle ensure consistent contact. Order the Tube wall thickness micrometer directly via Metav Werkzeuge or ask our consultants if needed. Microtech CertiMet TUBE digital tube wall thickness micrometer — IP65, ISO 17025-calibrated Microtech CertiMet TUBE is a digital tube wall thickness micrometer for industrial inspection and shop-floor quality control, engineered for repeatable measurements on cylindrical components. Digital readout with 0.001 mm resolution IP65 aluminium housing for harsh environments ISO 17025 calibration certificate included Friction thimble and rotating spindle for stable contact Reliable accuracy for production control The instrument provides a verified measurement chain with a stated accuracy of 0.003 mm and a display resolution of 0.001 mm, making it suitable where small deviations affect part performance. The robust electronic readout removes the uncertainty of analogue scales while the friction thimble maintains a uniform contact force during measurement, reducing operator-induced variation. This combination supports faster decision-making in quality control and reduces rework by ensuring that wall-thickness readings are consistent and comparable across batches. Built for the workshop and the field An aluminium housing with IP65 protection allows the micrometer to be used in workshops where coolant spray, dust or fluctuating conditions are present. The rotating spindle and friction ratchet ensure precise approach and repeatable closure on tubes, while the compact form factor supports inspections in confined fixturing or on assembled equipment. The device’s robustness and ergonomic handling translate into fewer interrupted measurements and less downtime during routine checks. Traceability and conformity for documented quality Delivered with an ISO 17025 calibration certificate (Ilac MRA), the micrometer arrives ready for use in audited quality systems and supplier chains that require documented measurement confidence. The certificate establishes traceability to national standards, simplifying incoming and final inspection documentation. For regulated production environments or when supplier certification is requested, this accredited calibration provides clear evidence of measurement competence. Practical functions and adaptability in application The instrument offers quick-switch functions — mm/inch, origin set and a hold feature — that streamline inspection workflows and reduce post-processing. A custom-size tube anvil can be supplied on request to suit non-standard pipe geometries, and the tool is specifically suited for tube wall thickness measurements starting from around 4.7 mm, addressing small-diameter tubing as well as larger sections within its 75–100 mm measuring range. These capabilities improve throughput by tailoring the micrometer to the part rather than adapting the part to the tool. Discuss application requirements or secure the Microtech CertiMet TUBE with Metav Werkzeuge — our specialists in Emmerich provide specification advice, calibration documentation and delivery coordination Technical Data Article number: 110351001 GTIN: 4061905040658 Manufacturer: Microtech Metrology Facts Measuring range: 75–100 mm Resolution (reading): 0.001 mm Accuracy: 0.003 mm Protection class: IP65 Display type: digital Special features Friction thimble (friction ratchet) Rotating spindle Functions: mm/inch, origin, hold Aluminium housing Calibration certificate: ISO 17025 (Ilac MRA) Custom tube anvil available on request Suitable for tube wall thickness measurements from 4.7 mm FAQ Is the micrometer supplied calibrated? Yes. The CertiMet TUBE is delivered with an ISO 17025 calibration certificate, ensuring traceability and suitability for audited quality systems. Can the instrument be used in damp or dusty environments? The aluminium housing and IP65 rating protect the electronics and mechanisms against dust ingress and water jets, making it suitable for demanding workshop conditions. What measurement range and resolution are available? The device covers a 75–100 mm measuring range with a display resolution of 0.001 mm and an accuracy of 0.003 mm. Is a customised anvil available for special tube shapes? Yes, Microtech Metrology can supply a custom-size tube anvil on request to match unusual geometries and ensure correct contact for wall-thickness readings. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-100mm Universal Micrometer Screw Gauge Colour Touchscreen, ISO 17025 Calibrated, IP65 - Microtech Metrology
Take advantage of precision measurement, robust protection and fully traceable delivery: the combination of 0.004 mm accuracy, ISO 17025 calibration and wireless plus USB data output ensures reliable results and efficient documentation. Order the micrometer directly via Metav Werkzeuge or consult our specialists for application advice. Universal micrometer — Digital micrometer with 2.4" touchscreen and wireless + USB, Microtech Metrology The Universal micrometer is a precision digital micrometer for workshop and laboratory measuring tasks, covering the 75–100 mm range for component inspection and quality control 0.004 mm high precision measurement Colour 2.4" touchscreen display Wireless and USB data output Supplied calibrated to ISO 17025 Reliable precision where repeatable results matter The instrument delivers a 0.004 mm specification for measurement uncertainty, together with a display resolution of 0.0001 mm, giving clear numeric feedback for fine tolerances. A non-rotating spindle reduces torsional error during measurement, improving repeatability when comparing batches or validating process changes. Supplied measuring anvils in seven matched pairs make setup faster when switching between external and stepped measurements, reducing fixture time and potential operator variation. Seamless data capture and documented traceability Integrated wireless and USB interfaces provide immediate data transfer to inspection software or SPC systems, cutting transcription time and lowering the risk of manual entry errors. The large 2.4" colour touchscreen simplifies reading and parameter adjustments on the bench. Delivered fully calibrated to ISO 17025, the instrument includes a traceable calibration certificate, ensuring each result can be linked to recognised laboratory standards for audits and supplier acceptance. Built for daily use in harsh production environments With an IP65 rating, the micrometer withstands chips, coolant splashes and shop‑floor dust while maintaining measurement integrity. The 75–100 mm measuring span places this instrument in the micro class (maximum range 10–100 mm), which balances compact handling with sufficient reach for precision components; the size is particularly suited to fine mechanical work and quality control of small to medium parts. Robust construction and an ergonomic form factor keep operator fatigue low and handling consistent across repetitive tasks. Practical advantages for procurement and inspection workflows Choosing this digital micrometer reduces inspection cycle time and scrap through faster, more reliable measurements and direct data logging. The combination of tactile touchscreen control, sealed protection and wireless data transfer supports both bench use and integration into automated inspection routines. Metav’s quality filter in Emmerich assures central European supply reliability and a comprehensive product range, simplifying sourcing and post‑purchase traceability for production and maintenance teams. For ISO 17025‑calibrated precision and seamless data integration, contact Metav Werkzeuge in Emmerich for personalised advice and supply coordination: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 110751008 GTIN: 4061905040368 Manufacturer: Microtech Metrology Facts Measuring range: 75–100 mm Accuracy: 0.004 mm Display resolution: 0.0001 mm Display: Colour 2.4" touchscreen Protection class: IP65 Special features Digital instrument with wireless and USB data output Supplied with 7 pairs of measuring anvils Non-rotating measuring spindle Delivered calibrated to ISO 17025 with certificate Suitable for workshop and laboratory inspection FAQ What measuring range does the micrometer cover? The micrometer covers a measuring range of 75–100 mm, suitable for micro‑class inspection tasks and fine mechanical components. Is the instrument delivered calibrated and traceable? Yes — the micrometer is delivered fully calibrated to ISO 17025 and includes a calibration certificate for traceability. How is measurement data exported from the instrument? Measurement data can be exported via wireless and USB interfaces for direct import into inspection software or SPC systems. Can the micrometer withstand shop‑floor conditions? The instrument has an IP65 rating, providing protection against dust and water jets typical on production floors. Which accessories are supplied with the micrometer? The delivery includes seven pairs of measuring anvils for rapid reconfiguration between different measurement tasks (SKU 110751008, Microtech Metrology) Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-88mm Digital Three-Point Internal Micrometer With Carbide Measuring Faces, RB6, No Setting Ring - Metav IndustryLine
Benefit from high-precision measurement, robust carbide measuring faces and a clear digital readout for reliable internal bore checks in production. Combine repeatable ±0.005 mm accuracy with blind‑hole capability and straightforward data output — order the M312.221 directly via Metav Werkzeuge or consult our specialists for technical advice. M312.221 Digital three-point internal micrometer (75–88 mm) by Metav IndustryLine The M312.221 is a digital three-point internal micrometer designed for precision measurement of blind-hole bores and internal diameters in workshop and production environments. Digital display with mm/inch and hold High accuracy ±0.005 mm Carbide measuring faces for wear resistance Built for blind‑hole measurements Precise results for internal bore inspection The three‑point measuring principle provides a stable, concentric contact in cylindrical bores: the spring‑loaded anvils expand evenly to centre on the bore, reducing eccentricity and improving repeatability. With a stated accuracy of ±0.005 mm and a display resolution of 0.001 mm, this instrument is suited to metrological tasks that require fine tolerances. The design helps to convert small hand movements into a clear numerical result, making it easier to maintain process control and reduce rework. Clear digital handling and data transfer The integrated digital display offers ON/OFF/SET, HOLD and quick mm/inch switching to speed measurement cycles and avoid transcription errors. Readouts at 0.001 mm resolution make small deviations visible at once. The tool also provides a RB 6 data output interface for downstream recording or process documentation, allowing measured values to be captured electronically for quality records and SPC workflows, which supports faster decision‑making on the shop floor. Robust measuring faces and application scope Carbide (HM) measuring faces give hard, wear‑resistant contact surfaces that maintain measurement integrity over repeated use. The instrument’s range of 75–88 mm targets medium internal diameters commonly found in components and fixtures; its capability for blind‑hole measurement makes it a practical choice where depth limits conventional probes. The construction balances rigidity with ergonomic handling to reduce operator influence on the result. Practical benefits in production environments Using a three‑point internal micrometer streamlines inspection of bores without complex fixturing: measurements are performed rapidly with reproducible contact geometry, which supports throughput in batch inspections. The combination of digital readout, robust carbide faces and electronic data output reduces manual entry errors, shortens inspection times and helps maintain traceable measurement records for quality assurance. Suitable for workshop use and routine quality control applications. Choose the M312.221 from Metav IndustryLine for dependable internal bore measurement — contact Metav Werkzeuge for tailored technical guidance and swift dispatch from Emmerich. Technical data SKU: M312.221 GTIN: 4054469169187 Manufacturer: Metav IndustryLine Label: Digital three-point internal measuring, 75–88 mm, RB6 with carbide measuring faces Eclass: 21170335 ETIM: EC003590 Facts Measuring range: 75–88 mm Accuracy: ±0.005 mm Resolution (display): 0.001 mm Weight: 4 kg Tariff number: 90173000 Special features Carbide measuring faces (HM) Digital display with ON/OFF/SET, HOLD, mm/inch Data output: RB 6 Suitable for blind‑hole measurements Category: Micrometers (Messschrauben) FAQ What measuring range does this instrument cover? The instrument covers a measuring range of 75–88 mm, designed for medium internal diameters. How precise are the results from this three‑point micrometer? The device delivers an accuracy of ±0.005 mm with a display resolution of 0.001 mm, suitable for fine tolerance checks. Is the tool suitable for blind‑hole measurements? Yes, the design is specifically suitable for blind‑hole measurement and is supplied without extensions or a setting ring. Are the measuring faces hardened for long service life? The micrometer is fitted with carbide (HM) measuring faces, providing high wear resistance for repeated use. What data interface is provided for process documentation? A RB 6 data output is available to transfer measured values electronically into quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Digital Gauge With Tungsten Carbide Faces, IP65, Setting Ring - Metav IndustryLine
Take advantage of high repeatability and workshop-ready protection: the combination of ±0.005 mm accuracy and IP65 ingress protection ensures reliable internal measurements in demanding environments. Order the device directly via Metav Werkzeuge or consult the Metav team for application advice and measuring strategy. Metav IndustryLine Digital Three‑Point Internal Micrometer, 75–88 mm – IP65, carbide faces The Metav IndustryLine digital three‑point internal micrometer offers a compact, workshop‑rated solution for precise internal diameter measurement, especially where blind‑hole checking and repeatable contact are required. IP65 protection for harsh environments Carbide measuring faces for wear resistance Resolution 0.001 mm digital readout Suitable for blind‑hole measurements Confidence where tolerance matters The instrument delivers high repeatability with an indicated accuracy of ±0.005 mm, supported by a display resolution of 0.001 mm. Its three‑point measuring head ensures stable contact around the bore, which reduces eccentricity errors common with single‑point probes; this is particularly beneficial when inspecting small bores or stepped internal diameters. The device conforms to DIN 863 measurement principles and is classified for the micro measurement range (up to 100 mm), making it well suited for precise checks in toolmaking, gauge workshops and quality control stations where consistent, verifiable results are required. Built for the workshop and production floor Designed to withstand routine industrial use, the micrometer features IP65 protection and carbide measuring faces, which together extend service life and reduce downtime from cleaning or wear. The ingress rating protects electronics and mechanics from coolant spray and fine dust, enabling measurement close to the machine centre without compromising accuracy. A robust construction and clear digital display minimise handling errors, so process control becomes more efficient and inspection throughput improves without sacrificing traceability. Fast setup and traceable output Practical features reduce setup time and support data collection: the unit is supplied with a setting ring and an extension, facilitating rapid calibration to reference diameters and access to deeper bores. The digital display includes ON/PRESET, mm/inch and HOLD functions for flexible use across inspection routines, while the RB 6 data output allows integration with data loggers or inspection software for downstream documentation. These features combine to speed routine checks and feed reliable measurement data into quality systems, helping standardise inspection across shifts and operators. Choose the Metav IndustryLine three‑point internal micrometer for robust, repeatable internal measurements and contact Metav Werkzeuge in Emmerich for application-specific guidance or to arrange a purchase — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical Data Article number: M312.241.PN GTIN: 4054469179179 ECLASS: 21170335 ETIM: EC003590 Standard: DIN 863 Facts Measuring range: 75–88 mm Resolution (display): 0.001 mm Accuracy: ±0.005 mm Weight: 3.5 kg Setting ring: 87 mm Special features IP protection: IP 65 Measuring faces: carbide (HM) Digital display functions: ON/PRESET, mm/inch, HOLD Data output: RB 6 Suitable for blind‑hole measurements Includes setting ring and extension (150 x Ø23.5) Tariff number: 90173000 FAQ What measurement range does this instrument cover? The Metav IndustryLine digital three‑point internal micrometer covers a measuring range of 75–88 mm (SKU M312.241.PN) and is tailored to micro‑range internal inspection tasks. How accurate is the device for quality control use? Accuracy is specified at ±0.005 mm with a display resolution of 0.001 mm, making the instrument suitable for demanding workshop and inspection applications where small tolerances are monitored. Can it be used on blind holes? Yes — the device is suitable for blind‑hole measurements and is supplied with a setting ring and extension to simplify calibration and reach into recesses. What environmental protection does it offer? The unit is rated IP65, providing protection against dust ingress and low‑pressure water jets, which supports use close to machining centres and in typical production environments. How can measurement data be exported? The micrometer provides an RB 6 data output for wired data transfer to logging devices or inspection systems, enabling traceable recording of measured values. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Micrometer 0.001mm Readout With Setting Ring And 152.4xØ23.5 Extension, In Case - Metav IndustryLine
Take advantage of the combination of sub‑micrometre reading, robust handling and delivery in a protective case for reliable internal measurements of blind bores; order the instrument directly via Metav Werkzeuge or consult our specialists if additional information is required. Three‑point internal micrometer M312.462 — 75–88 mm, 0.001 mm reading (Metav IndustryLine) A three‑point internal micrometer M312.462 engineered for precision measurement of internal diameters and blind holes within the 75–88 mm range. 0.001 mm reading resolution Range 75–88 mm for internal diameters Suitable for blind‑hole measurements Includes setting ring and extension rod in case Precision for fine internal measurements that repeat reliably The three‑point design provides stable contact with the bore and reduces alignment errors common to two‑point probes, yielding a genuine 0.001 mm reading and an indicated measurement uncertainty of ±0.005 mm. This fine resolution, combined with the matt chrome‑plated scale and vernier, is especially valuable where small deviations matter: calibre inspection, small‑batch production and maintenance tasks that demand traceable results. Classified within the micro range (maximum measuring span up to 100 mm), the instrument is optimised for compact assemblies where stiffness and control are decisive for repeatable results. Complete accessory set for practical workshop use Delivery includes an 87 mm setting ring, extension rod (152.4 × Ø23.5 mm) and a protective transport case, ensuring the measuring system is ready for immediate use and secure in transit. The hardened measuring faces preserve contact geometry and extend service life when measuring internal diameters or blind bores, while the overall construction allows single‑person handling when accessibility is constrained. The configuration reduces time spent on set‑up and rework, supporting efficient quality control routines in small parts manufacture. Durability and traceable handling for everyday metrology Durable finishes and carefully chosen components make this instrument a pragmatic choice for workshops and inspection benches that require robust, low‑maintenance tools. The three‑point mechanism minimises operator‑induced variation and the matt chrome‑plated scale resists glare for easier reading under shop lighting. Backed by Metav’s quality filter in Emmerich, the device combines practical workshop resilience with the measurement clarity needed to lower scrap rates and speed troubleshooting across mechanical and precision engineering contexts. For further specification checks or to arrange delivery through Metav Werkzeuge, please contact our team in Emmerich for tailored advice and next‑day dispatch options at info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: M312.462 GTIN: 4054469182230 Manufacturer: Metav IndustryLine Facts Measuring range: 75–88 mm Resolution: 0.001 mm Accuracy: ±0.005 mm Weight: 4.3 kg Setting ring size: 87 mm Extension rods: 152.4 × Ø23.5 mm Special features Three‑point internal measuring system Hardened measuring faces Scale and vernier matt chrome‑plated Suitable for blind‑hole measurements Delivered in protective case FAQ What measuring range does the instrument cover? The instrument covers internal diameters from 75 to 88 mm as supplied with the standard setting ring. What resolution and accuracy can be expected? A reading resolution of 0.001 mm is provided with an overall stated uncertainty of ±0.005 mm for typical workshop conditions. Is the micrometer suitable for blind‑hole measurements? Yes, the three‑point configuration and included accessories are specifically intended for reliable measurement of blind bores. Which accessories are included with delivery? Delivery includes an 87 mm setting ring, an extension rod (152.4 × Ø23.5 mm) and a protective transport case. How does the three‑point system improve repeatability? The three‑point contact creates a self‑centering effect inside the bore, reducing alignment errors and operator influence on the measurement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Micrometer Colour Touchscreen, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of traceable calibration and fast digital data capture together with precise internal measurement capability to streamline quality checks and reduce rework. Order the instrument directly via Metav Werkzeuge or consult the team for specification matching and delivery options. Three‑point internal micrometer — digital instrument with Wireless + USB connectivity (Microtech Metrology) The three‑point internal micrometer is a precision instrument intended for reliable inside‑diameter measurement of small to medium bores in precision engineering and workshop inspection. Wireless and USB data output 1.54" colour touchscreen display ISO 17025 calibration certificate included High measurement accuracy ±0.004 mm Traceable precision for critical bore controls This instrument delivers laboratory‑grade traceability by being supplied with an ISO 17025 calibration certificate, which documents the reference conditions and measurement uncertainty. With a specified accuracy of ±0.004 mm and a reading step of 0.0001 mm, the tool supports reproducible evaluation of internal diameters where tolerance stacks are tight. The certificate and measured performance reduce audit risk, support incoming inspection protocols and simplify compliance tasks in regulated production chains. The combination of verifiable accuracy and documented calibration helps to lower scrap rates and avoid repeated machining cycles. Fast digital capture that fits modern workflows Integrated Wireless and USB outputs plus a 1.54" colour touchscreen ensure that captured values are transmitted quickly into data collection systems, eliminating manual transcription. The touchscreen makes single‑value checks and quick zeroing straightforward; the digital interface reduces operator interpretation and speeds up statistical process control loops. For production environments that require rapid sampling or batch documentation, the instrument supports efficient collection of measurement data and seamless handover to quality‑management software, improving throughput without sacrificing measurement integrity. Compact measurement range with extended depth access With a measurement span of 75–88 mm, this gauge sits within the compact measurement class (up to 100 mm), ideal for fine mechanical components and small assemblies where tight clearances occur. The specified measuring depths of 112 + 150 mm provide extra reach for recessed bores and stepped internal features, so the same instrument can handle standard internal diameters and deeper pockets without improvised extensions. The included adjustment ring simplifies fine zeroing and adaptation to reference standards, which contributes to quicker set‑up times in batch inspections. Simple handling for repeatable results A clear digital readout combined with a fine adjustment mechanism reduces reading uncertainty and operator influence during measurement. The instrument's electronic display presents values unambiguously, while the adjustment ring allows controlled approach and exact zeroing at datum points. These characteristics make the gauge suitable for shop‑floor use where multiple operators perform checks; repeatable readings are achieved more easily than with purely mechanical comparators, helping to maintain consistent quality over production shifts. Contact Metav Werkzeuge today to discuss delivery times, calibration options and how the Microtech Metrology three‑point internal micrometer (SKU 133508810) can be integrated into existing inspection routines Technical data Manufacturer: Microtech Metrology SKU: 133508810 GTIN: 4061905041860 eClass: 21170335 ETIM: EC003590 Data output: Wireless+USB Display: Color 1.54" Touchscreen Adjustment ring: included Calibration: ISO 17025 certificate included Numbers / Core technical data Measurement range: 75–88 mm Measuring depth: 112 + 150 mm Accuracy: 0.004 mm Resolution / reading: 0.0001 mm Special features / Versions Digital instrument Wireless data transmission USB connection Colour touchscreen interface ISO 17025 calibrated and certified FAQ What measurement range does this instrument cover? The measurement range is 75–88 mm; the device also offers measuring depths of 112 and 150 mm for access into recessed bores. Is the instrument delivered calibrated? Yes. The Microtech Metrology three‑point internal micrometer is supplied fully calibrated with an ISO 17025 calibration certificate. How are readings exported to inspection software? Readings are transmitted via Wireless or USB; the digital outputs are suited for direct integration into SPC or quality‑management systems. What accuracy and resolution can be expected? The instrument specifies an accuracy of ±0.004 mm with a display/readout resolution of 0.0001 mm. Does the micrometer include fine‑adjustment features? An adjustment ring is included to enable controlled approach and precise zeroing during measurement. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
75-88mm Three-Point Internal Micrometer Digital, Measuring Drum With Scale, IP65 - Metav IndustryLine
Take advantage of the combination of high-resolution measurement (0.005 mm), a robust IP65-protected housing, and a digital readout with ABS/INC/UNIT functions for reliable, repeatable bore inspection; order the instrument directly via Metav Werkzeuge or consult our specialists for application support. Three-point inside micrometer M312.241.M — digital instrument, 75–88 mm measuring range (Metav IndustryLine) The Three-point inside micrometer M312.241.M is a digital instrument designed for precise internal measurements, especially suited to blind-hole and bore inspections in workshop and production environments. Digital display with ABS/INC/UNIT Accuracy 0.005 mm (5 µm) Measuring range 75–88 mm IP65 protection for harsh environments Precision that reduces rework and speeds inspection The instrument’s three-point measuring system guarantees concentric contact in blind bores, reducing alignment errors compared with two-point gauges. With an accuracy of 0.005 mm, the gauge provides results in the sub‑10 µm class suitable for demanding quality control tasks. The digital readout with ON/OFF/SET and ABS/INC/UNIT keys simplifies measurement logging and minimises transcription errors, which in turn shortens inspection cycles and improves throughput. Designed for reliable use in workshop conditions Built to DIN 863 standards, the micrometer is finished with a matt‑chromed scale and vernier for durable legibility. The instrument complies with IP65 protection, keeping dust and water jets at bay so that measurements remain reliable on the shop floor. Hardened measuring faces ensure wear resistance during repeated contact with internal surfaces. Delivered complete with a setting ring and an extension, the instrument is ready to handle varied bore depths and workpiece geometries. Practical handling and traceable delivery for production use The device is supplied in a protective case for safe transport and storage and includes the extension specified (150 × Ø23.4). The integrated measuring thimble with scale assists in coarse positioning before the digital readout is used for fine value capture. The combination of tactile control and electronic display supports both traditional workflow and digitised data capture via the available data output RB 4.1, enabling integration into inspection routines where recorded values are required. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating the M312.241.M into existing quality processes and to arrange prompt delivery from our European stock. Technical data SKU: M312.241.M GTIN: 4054469162423 Article number: M312.241.M Norm: DIN 863 Data output: RB 4.1 Facts Measuring range: 75–88 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm (5 µm) Weight: 4.3 kg Overall length: 114 mm Special features Digital display with ON/OFF/SET and ABS/INC/UNIT Three-point measuring system for blind bores Measuring thimble with scale Delivered with setting ring and extension (150 × Ø23.4) IP65 protection Matt‑chromed scale and vernier Hardened measuring faces Protective transport case included FAQ What accuracy can be expected from this instrument? The M312.241.M three‑point inside micrometer delivers an accuracy of 0.005 mm (5 µm), making it suitable for high‑precision internal measurements. Is the gauge suitable for measuring blind holes? Yes. The instrument is expressly designed for blind‑hole inspection and includes a three‑point system and an extension (150 × Ø23.4) for deeper bores. Does the device allow digital data transfer? The micrometer features a data output RB 4.1, enabling digital integration where required; the instrument also provides ABS/INC/UNIT functions on the display. What protection does the housing offer in workshop environments? The gauge carries IP65 protection, ensuring reliable operation in dusty environments and against low‑pressure water jets. Which accessories are supplied with the micrometer? The product is supplied with a setting ring, the stated extension, and a protective case for safe transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Micrometer Self-Centring, Hardened Measuring Faces, Supplied in Case - Metav IndustryLine
Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Micrometer With Carbide Measuring Faces, Adjustment Ring, Supplied In Case - Metav IndustryLine
Take advantage of the combination of three‑point measuring, carbide contact faces and fine 0.005 mm resolution for reliable internal measurements in tight bores; the instrument is supplied in a protective case with a setting ring for repeatable results. Order via Metav Werkzeuge or consult the team for application advice. M312.162 Three‑point internal micrometer 75–88 mm – carbide measuring faces (Metav IndustryLine) The M312.162 is a precision three‑point internal micrometer designed for accurate measurement of small bores and blind holes in fine mechanical and workshop environments. Three‑point internal measurement 75–88 mm Carbide measuring faces for wear resistance Mechanical vernier with 0.005 mm resolution Supplied in protective case with setting ring Precision where compact measurement matters The instrument’s three‑point design gives stable, concentric contact in confined bores, translating to repeatable results even on short depth runs. Classified in the micro range (maximum measuring range up to 100 mm), this format is ideal where stiffness and compactness are paramount. The analogue vernier provides a 0.005 mm reading increment and an indicated accuracy of 0.005 mm, offering a clear, objective basis for quality control in small‑part inspection and toolmaking. Compliance with DIN 863 underlines its suitability for standardised workshop and inspection tasks. Durable contacts and consistent repeatability Hard‑facing at the contact points ensures longevity: the carbide measuring faces resist wear and maintain geometry across frequent cycles, reducing the need for premature replacement and minimising measurement drift. The integrated setting ring allows quick verification of the instrument’s span before a measurement run, supporting process control and traceability. The mechanical construction and robust materials mean the tool performs reliably in production and maintenance environments, contributing to reduced rework and improved first‑pass yield. Ready for workshop use and straightforward care Delivered in a protective case, the micrometer is ready to be carried or stored safely between uses, while the matt chrome‑plated scale and vernier reduce glare for easier reading under workshop lighting. The design suits both blind‑hole and through‑bore inspection, with the geometry optimised for small bores and precision assemblies. Routine care—keeping the carbide faces clean and lightly oiled after use and checking the setting ring periodically—keeps the instrument within its specified performance range. For specialised requirements, Metav IndustryLine options and accessories such as the noted extensions are available to adapt the tool to particular fixtures or reach conditions. Discuss your bore measurement requirements with Metav Werkzeuge to select the right Metav IndustryLine three‑point internal micrometer and secure repeatable accuracy for your workshop Technical data Article number: M312.162 GTIN: 4054469119694 Category: Micrometers Standard: DIN 863 Facts Measuring range: 75–88 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Overall length: 114 mm Setting ring: 87 mm Special features Carbide measuring faces Scale and vernier matt chrome‑plated Suitable for blind‑hole measurement Supplied in protective case Analogue vernier operation Extensions: 150 x Ø23.4 FAQ How accurate is the instrument for small‑bore inspection? The M312.162 three‑point internal micrometer is specified with a reading increment of 0.005 mm and an accuracy of 0.005 mm, making it suitable for precise checks in fine mechanical and small‑part production. Can blind holes be measured reliably with this tool? Yes. The three‑point contact geometry and carbide faces are especially effective for blind‑hole measurement, providing concentric contact and repeatable readings in shallow and medium‑depth bores. Is this micrometer appropriate for a workshop environment? The compact micro‑range format and robust construction from Metav IndustryLine suit workshop use; the matt chrome finish and protective case make it practical for daily handling and storage. What maintenance keeps the measuring faces accurate? Keep the carbide faces free of chips and contamination, apply light corrosion protection after cleaning, and verify span with the setting ring before critical measurements to maintain the micrometer’s performance. Are there extension or accessory options for specialised tasks? Yes. The instrument can be adapted with the listed extensions and uses the supplied setting ring to verify span; for further accessory options consult Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75-88mm Three-Point Internal Micrometer With Setting Ring And Extension, Calibrated ISO 17025, In Case - Metav IndustryLine
Take advantage of the combination of industrial-grade repeatability, a compact 75–88 mm measuring range and a 0.005 mm reading for reliable internal diameter checks; the three-point measuring principle ensures stable contact even in blind bores, and the tool is supplied with a setting ring and an extension for immediate use – order directly via Metav Werkzeuge or consult our specialists for specification support. Three-point internal micrometer – 75–88 mm range, 0.005 mm reading (Metav IndustryLine) The Three-point internal micrometer is a precision instrument designed for accurate measurement of internal diameters, especially in blind holes and restricted access bores within workshop and inspection environments. Three-point measuring system for blind holes Measurement range 75–88 mm Resolution 0.005 mm for repeatable results Includes setting ring and extension 150×Ø21.8 Precision where small differences matter The instrument delivers a 0.005 mm reading and an overall accuracy suited to demanding inspection tasks, making it a dependable choice for quality control and toolroom work. The three-contact measuring head centres itself in the bore, reducing eccentricity and providing a stable reference compared with single-point probes; this equals faster cycle times and fewer re-measurements in serial checks. Classified within the standard range for workshop metrology, the tool balances reach and rigidity for everyday machining and inspection tasks. Engineered for blind-hole and restricted-access measurement Designed specifically for blind-hole measurement, the three-point mechanism obtains full circumferential contact inside the bore, which avoids the need to access the far side of a component. The delivery includes a setting ring (Ø87) and an extension 150×Ø21.8, enabling measurement of deeper or recessed bores without improvised fixtures. This configuration reduces handling and fixture time on the shop floor, helping to maintain throughput while preserving measurement quality when space is constrained. Robust construction for repeatable results Built for industrial use, the instrument features hardened measuring faces and a matt chrome-plated scale and vernier, which resist wear and ensure legible graduations over long service intervals. The solid build contributes to consistent readings across production batches; recorded weight and length reflect a design aimed at stability rather than featherlight portability, helping to reduce user-induced variation. For applications requiring dependable mechanical performance, this design minimises the variables between successive measurements. Practical application and workshop integration This internal micrometer is well suited to machine shops, maintenance departments and inspection benches where blind or recessed bores are encountered regularly. Typical tasks include checking counterbores, stepped bores and blind-hole diameters during incoming inspection or first-off verification. The analogue vernier readout provides tactile feedback familiar to technicians, while the instrument’s geometry simplifies repeat measurement routines without complex electronic set-up. For procurement planning and integration into existing quality workflows, the product aligns with industry expectations for durability and usability. For shops needing sub‑0.01 mm repeatability, contact Metav Werkzeuge for procurement assistance and specification matching: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: M312.162.P GTIN: 4054469158808 Customs tariff number: 90173000 Category: Internal micrometers (Messschrauben) Manufacturer: Metav IndustryLine Facts Measuring range: 75–88 mm Reading / resolution: 0.005 mm Stated accuracy: 0.005 mm Length: 90 mm Weight: 4.3 kg Setting ring: Ø87 Extension: 150×Ø21.8 Special features Three-point measuring system for blind holes Hardened measuring faces Scale and vernier matt chrome-plated Includes setting ring and extension Analog vernier instrument Suitable for blind-hole bores FAQ What measurement range does the micrometer cover? The Three-point internal micrometer covers a measuring range of 75–88 mm, suitable for many workshop and inspection tasks. What level of resolution and accuracy is available? The instrument provides a reading and stated accuracy of 0.005 mm, enabling repeatable checks in medium‑precision metrology. Is this tool suitable for blind-hole measurement? Yes, the three-point design is specifically intended for blind-hole bores; the micrometer is supplied with a setting ring and an extension to support recessed measurements. What materials protect the scale and graduations? The scale and vernier are matt chrome-plated, chosen to reduce glare and resist wear under workshop conditions. Can the micrometer be used for depth or stepped measurements? The geometry supports internal diameter checks including stepped bores; the included extension allows access to deeper features where required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Disc Anvil Micrometer, 20mm Disc, Ratchet Stop, Painted Frame, Matt Chrome Thimble - Metav IndustryLine
The combination of ±0.005 mm accuracy, a ratchet stop and a non-rotating spindle ensures reliable, repeatable thickness checks on flat components; delivered in a protective transport case for safe handling. Order the instrument directly via Metav Werkzeuge or consult the Metav team for application advice. M309.252 Disc-Anvil Micrometer, 50–75 mm, Ø20 mm — Metav IndustryLine The M309.252 disc-anvil micrometer is a precision mechanical instrument for workshop and inspection use, designed for repeatable measurements of flat and slightly profiled surfaces within the 50–75 mm range. High-precision ±0.005 mm accuracy Disc anvil Ø20 mm for flat surfaces Non-rotating spindle with ratchet stop Delivered in protective transport case Reliable measurement performance for production control Equipped with a finely graduated thimble and a rated accuracy of ±0.005 mm, this analogue micrometer delivers consistent results for routine quality checks and dimensional control. The engraved scale provides a 0.01 mm readout, while the ratchet stop limits applied measuring force to reduce operator-induced variation. Together with the non-rotating spindle, these features minimise wear on the workpiece and deliver stable repeatability, making the tool suitable for shop-floor inspection and routine process monitoring in metalworking and toolmaking. Robust design that supports fast, ergonomic handling The instrument combines a painted frame with a matt-chrome plated measuring drum, offering a durable surface finish that resists everyday knocks and contamination. The Ø20 mm disc anvil spreads contact pressure and stabilises readings on flat components, while a compact mass of 0.8 kg keeps the micrometer easy to manoeuvre during repetitive tasks. Delivery includes a protective transport case to safeguard the instrument between uses and during transport, improving service life and reducing downtime for maintenance or replacement. Practical fit for workshop and inspection environments With a measuring range of 50–75 mm, this micrometer covers medium-sized parts typical in general machining, fixture production and component assembly. The mechanical construction supports straightforward use without electronics, which simplifies maintenance and long-term reliability in harsh workshop conditions. As part of the Metav IndustryLine, the instrument is identified by GTIN 4054469118710 and SKU M309.252, ensuring traceability and straightforward stock management for procurement and calibration planning. For precise, workshop-ready measurement from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply directly from the European quality hub. Technical Data Article number: M309.252 GTIN: 4054469118710 Manufacturer: Metav IndustryLine Facts Measuring range: 50–75 mm Measuring range min: 50 mm Measuring range max: 75 mm Resolution/readability: 0.01 mm Accuracy: ±0.005 mm Weight: 0.8 kg Special features Disc anvil Ø20 mm Frame painted Measuring drum matt chrome-plated Non-rotating spindle Ratchet stop Analogue micrometer Delivered in protective transport case FAQ What measuring range does this micrometer cover? The M309.252 covers a measuring span of 50–75 mm, suitable for medium-sized components commonly found in machining and assembly. How precise is the device and what is the readout? The instrument has an accuracy of ±0.005 mm with a readout graduation of 0.01 mm for clear analogue measurement. Why is the non-rotating spindle important? A non-rotating spindle prevents surface scuffing on the workpiece and improves repeatability; this feature is incorporated in the M309.252 for reliable flat-surface checks. What benefit does the Ø20 mm disc anvil provide? The disc anvil increases contact area on flat or thin-walled parts, reducing local deformation and yielding more stable measurements. Is the micrometer supplied ready for transport? The M309.252 is supplied in a protective transport case to ensure safe handling and storage between uses. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Setting Gauge 55° For Thread Micro Inserts 60°/55° Options - Metav IndustryLine
Take advantage of a compact, dedicated reference that ensures reproducible thread settings: the 75 mm length and precise 55° profile deliver concise adjustment and reliable repeatability for workshop and inspection use. Order the setting gauge directly via Metav Werkzeuge or contact our consultants for further advice. Setting gauge 75 mm for thread micrometer, 55° — Metav IndustryLine The Setting gauge 75 mm for thread micrometer, 55° provides a stable reference for calibrating and adjusting thread measuring instruments, designed primarily for Whitworth thread inserts in workshop and quality‑control environments 75 mm precision setting gauge 55° angle for Whitworth thread inserts Robust accessory for thread micrometers Metav IndustryLine quality and traceability Reliable reference that reduces setup time and measurement uncertainty A compact 75 mm reference block serves as a quick and reproducible datum when adjusting thread measuring tools. By using a dedicated gauge rather than makeshift references, setup times are reduced and the risk of systematic error is minimised. The instrument acts as a clear mechanical standard for the contact faces of a thread micrometer, so machinists and inspection staff achieve consistent starting conditions across multiple setups, which improves overall repeatability and process reliability. Correct profile angle for Whitworth threads ensures contact accuracy The 55° profile corresponds to the Whitworth thread form, guaranteeing that the contact geometry of the gauge matches the flank angle of corresponding inserts. Where a 60° form is required for other thread inserts, that profile is commonly used; this item is the 55° variant intended for Whitworth applications. Matching the profile angle avoids misleading contact points during adjustment and supports correct functional assessment of gauging assemblies, contributing to dependable calibration outcomes. Workshop-friendly accessory built for smooth integration As a purpose-made accessory for thread metrology, the gauge occupies minimal bench space while delivering a tactile, stable reference for alignment and verification tasks. The compact format and clear geometry make it suitable for use at production benches and inspection tables alike, supporting faster tool changeovers and fewer adjustment iterations. Traceability and part identification are straightforward thanks to the visible SKU M309.091.2 and supplied identifiers, which aid stock management and quality documentation. Choose the Metav IndustryLine setting gauge 75 mm (55°) for dependable Whitworth calibration — contact Metav Werkzeuge in Emmerich for purchasing advice or technical clarification via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M309.091.2 GTIN: 4054469118123 ECLASS: 21170102 Customs tariff number: 90173000 Facts Length: 75 mm Angle: 55° Special features Accessory for thread micrometers Intended for Whitworth thread inserts (55°) 60° form used for other thread insert types Category: Zubehör (accessory) FAQ What is the primary purpose of this setting gauge? The setting gauge is a compact reference intended to calibrate and adjust thread measuring instruments, ensuring reproducible contact for thread micrometer adjustments. Is the gauge suitable for Whitworth threads only? This 55° variant is designed specifically for Whitworth thread inserts; alternatives with a 60° profile exist for other thread insert types. How does the gauge improve measurement consistency? Using the dedicated 75 mm block as a mechanical datum reduces setup variability and supports repeatable adjustment procedures, which enhances measurement consistency across production batches. Which product identifiers should be used for ordering or inventory? Reference Metav IndustryLine, SKU M309.091.2 and GTIN 4054469118123 when ordering or recording the item in inventory. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Setting Gauge For Micrometers With Thermal Shield, Accuracy ±0.002mm - Metav IndustryLine
Taking advantage of a compact 75 mm reference length together with a ±0.002 mm accuracy and integrated thermal protection ensures reproducible micrometer adjustments and efficient setup routines; order the setting gauge directly via Metav Werkzeuge or consult our specialists for application support. Setting Gauge for Micrometers M304.311 — 75 mm, ±0.002 mm, Thermal Protection A Setting Gauge for Micrometers M304.311 that provides a stable 75 mm reference for adjusting and checking external micrometer anvils in workshop and laboratory environments. 75 mm reference length for micrometer setting High accuracy ±0.002 mm tolerance Flat measuring faces for stable contact Integrated thermal protection for stability Precision where reproducibility matters The device functions as a reference standard for external micrometer calibration, offering a nominal length of 75 mm and a verified accuracy of ±0.002 mm (2 µm). This degree of precision places the gauge in a class suitable for routine workshop calibration and fine adjustment tasks where tight tolerances are required. The stated tolerance means that adjustments made against this standard will minimise measurement deviation during subsequent production or inspection steps, increasing process reliability and reducing scrap rates. Explanation of tolerance values and the role of a reference standard helps translate technical figures into operational benefits for quality assurance teams. Thermal control to avoid measurement drift Thermal influence is a common source of measurement error in small comparative gauges. The unit’s integrated thermal protection reduces heat transfer from hands or bench surfaces, limiting length expansion during handling. Combined with flat measuring faces, this reduces local contact distortions and helps preserve the true reference dimension while taking a reading. For repeated setups and sequential checks, thermal stability supports consistent results and fewer re-measures, which saves time on repetitive tasks and contributes to predictable inspection throughput. Practical handling and workshop integration Designed for straightforward use, the gauge is lightweight (approx. 0.1 kg) and easy to position against an external micrometer anvil; a nominal diameter of 7 mm defines the contact geometry for stable seating. As a dedicated accessory for micrometer adjustment, it shortens set-up cycles and improves operator confidence during routine verification. The compact size and robust working faces make the tool suitable for bench use in maintenance, toolroom and metrology benches alike. Where documentation is required, the clear numerical values allow immediate entry into calibration records or shop-floor checklists. For precise micrometer adjustment, choose the Metav IndustryLine M304.311 setting gauge — contact Metav Werkzeuge in Emmerich for technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M304.311 GTIN: 4054469116624 Manufacturer: Metav IndustryLine Short description: Setting gauge for micrometers, nominal 75 mm Dimensions & accuracy Nominal length: 75 mm Diameter: 7 mm Accuracy: ±0.002 mm Weight: 0.1 kg Tariff code: 90173000 ECLASS: 21170102 Features & applications Flat measuring faces Thermal protection Accessory for external micrometer adjustment Suitable for workshop and laboratory use FAQ What is the nominal length and accuracy of the gauge? The setting gauge has a nominal length of 75 mm and an accuracy of ±0.002 mm, suitable for fine adjustments and routine verification. Can this gauge be used to set external micrometer anvils? Yes, the M304.311 is designed specifically as a reference for setting external micrometer anvils and other similar comparative checks. How does the thermal protection benefit measurement tasks? Thermal protection reduces heat transfer during handling, limiting dimensional drift so that readings taken against the reference remain more stable and reproducible. Is the gauge suitable for both workshop and laboratory environments? The compact construction and flat measuring faces make the gauge appropriate for toolroom, maintenance and laboratory benches where a stable 75 mm reference is required. What is the contact geometry of the gauge? The gauge features flat measuring faces and a contact diameter of 7 mm, providing a stable seating surface for external micrometer anvils. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75mm Setting Gauge for Thread Micrometers 60° For Thread Inserts 0.03kg - Metav IndustryLine
Take advantage of precise 75 mm setting, compatibility with standard 60° and Whitworth 55° thread profiles, and a lightweight design for rapid, repeatable adjustment—ensuring consistent thread measurement setup. Order directly via Metav Werkzeuge for workshop-ready supply or consult our specialists for technical matching. Setting Gauge 75 mm (M309.097.2) — 60° Thread setting gauge, Metav IndustryLine The Setting Gauge 75 mm is a compact accessory designed to set and verify thread micrometers and thread inserts, providing reliable reference geometry for 60° thread profiles while accommodating Whitworth 55° inserts where specified. Precise 75 mm gauge length Compatible with 60° thread profiles Lightweight 34 g for easy handling GTIN and SKU identifiable Fast, measurable setup for thread metrology A compact setting gauge delivers measurable time savings at the workbench and in quality control. The 75 mm reference length creates a stable datum for aligning a thread micrometer, reducing the need for iterative adjustments and minimising setup time. Made for repeatable use, the lightweight construction at 0.034 kg allows quick handling without compromising contact stability. The direct mechanical geometry means setting is immediate and does not rely on external electronics, which supports efficient inline checks and simple integration into workshop routines. Compatibility that reduces uncertainty in thread checks This accessory supports common 60° thread insert profiles and, where required, can be applied to Whitworth 55° inserts owing to its specified angle options. Clear angular definition ensures the gauge reproduces the thread flank geometry needed to set micrometers and gauge anvils accurately. By matching the flank angle and reference diameter, the tool helps maintain measurement consistency across batches, thus lowering scrap rates and rework. The robust design is beneficial in mixed-production environments where multiple thread standards are encountered. Practical benefits for inspection and tool setup Designed as a straightforward reference tool, the gauge simplifies routine verification and setup procedures. Identification via SKU M309.097.2 and GTIN 4054469118253 makes it traceable in tool inventories and documentation. The simple form factor is suitable for bench-top use, enabling quick checks before critical machining steps or final inspection. As an accessory in the measurement toolkit, it contributes to a lean workflow: less repeated measuring, quicker pass/fail decisions, and clearer traceability of the setting process. Contact Metav Werkzeuge today for specific compatibility advice and ordering support from our Emmerich centre, where workshop-ready precision meets reliable supply Technical data Article number: M309.097.2 GTIN: 4054469118253 SKU: M309.097.2 Category: Messgeräte › Zubehör eCl@ss: 21170102 Facts Length: 75 mm Weight: 0.034 kg Angle: 60° Tariff number: 90173000 Special features 60° for thread inserts 55° option for Whitworth thread inserts Lightweight design for easy handling Accessory for thread micrometers Brand: Metav IndustryLine FAQ What is the purpose of this setting gauge? This setting gauge is a precision reference for setting and verifying thread micrometers and thread insert geometry, helping ensure accurate flank contact and repeatable measurements with the M309.097.2 accessory. Can the gauge be used for Whitworth threads? Yes, the accessory supports a 60° profile and includes the specification for a 55° flank, allowing application with Whitworth-style thread inserts where that angle is required. What are the identification details for inventory? The product is listed under SKU M309.097.2 and GTIN 4054469118253, which supports traceability in toolroom and inspection documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75–100 mm Digital Micrometer 0.001 mm Resolution, Ratchet, Stainless Measuring Faces, Supplied in Case - Metav IndustryLine
Take advantage of precise, repeatable external measurements and a clear digital readout to streamline inspection processes; the combination of 0.001 mm resolution, a secure ratchet stop and robust construction supports reliable quality control. Order the instrument directly via Metav Werkzeuge or consult our experts for specification guidance. Digital Micrometer M302.257 — 75–100 mm, 0.001 mm resolution The Digital Micrometer M302.257 is a workshop-grade outside micrometer designed for accurate external measurements in mechanical engineering and quality assurance tasks. 0.001 mm digital resolution ON/OFF, SET, ABS/INC/UNIT display Ratchet stop for consistent force Measuring faces 6.5 mm Increase measurement certainty with sub-micron readback The instrument offers a 0.001 mm display step across the 75–100 mm measuring span, which converts fine movements into a clear digital readout and reduces readout uncertainty compared with coarse analogue scales. Compliance with DIN 863 underlines its suitability for routine inspection and component acceptance; the thin, well-defined measuring faces 6.5 mm give a small contact footprint that is advantageous when measuring narrow bosses, shafts or turned features. This level of resolution supports tighter process control and faster decision-making in production environments. Consistent contact force and intuitive controls speed up workflows A built-in ratchet stop ensures a reproducible measuring force, reducing variation caused by operator pressure and improving repeatability across a batch of parts. The digital display features ON/OFF, SET and ABS/INC/UNIT modes for switching between absolute and incremental readings, zeroing at any position, and selecting units quickly—features that translate into fewer setup steps and less post-processing of measurement data. The frame is painted for durable handling while the matt chrome-plated thimble improves visibility and resists wear, together supporting efficient, fatigue‑reduced operation on the workshop bench. Robust construction designed for everyday use in the workshop Hardened contact faces and a sturdy frame provide the longevity required for frequent use in machining and inspection stations. The instrument includes a practical setting gauge reference (setting gauge from 25–50 mm) for straightforward calibration checks and set‑up routines. As part of the Metav IndustryLine, this micrometer pairs industrial-grade mechanics with clear digital functionality, making it a reliable choice for tasks where reproducibility and traceable workmanship are priorities. For reliable, workshop-ready precision choose the Metav IndustryLine digital micrometer and contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored technical advice Technical data Article number: M302.257 GTIN: 4054469151755 Category: Micrometers Standard: DIN 863 Digital display functions: ON/OFF, SET, ABS/INC/UNIT Resolution: 0.001 mm Measuring range: 75–100 mm Facts Measuring range: 75–100 mm Resolution: 0.001 mm Measuring faces diameter: 6.5 mm HS code: 90173000 eClass: 21170328 ETIM: EC003590 Design and special features Frame painted; measuring drum matt chrome-plated Ratchet stop for consistent measuring force Hardened measuring faces Setting gauge from 25–50 mm FAQ What resolution does the micrometer provide? The micrometer displays measurements with a resolution of 0.001 mm, allowing very fine discrimination within the 75–100 mm measuring range. Is the device suitable for workshop inspection tasks? Yes, the M302.257 is designed for workshop and quality-assurance use, complying with DIN 863 and providing repeatable readings for routine inspection and production control. How does the ratchet stop affect measurement quality? The ratchet stop ensures a consistent contact force at the measuring faces, which reduces operator-induced variation and improves repeatability across multiple measurements. Which display functions are available for measurement modes? The device includes ON/OFF and SET controls plus ABS/INC/UNIT functions, enabling zeroing at any point, switching between absolute and incremental modes, and changing measurement units. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75–100 mm Digital Micrometer With Friction Thimble, 0.001 mm Resolution, RB6 Data Output, Supplied In Case - Metav IndustryLine
The combination of 0.001 mm resolution, a friction ratchet for reproducible measuring force and a standardised RB 6 data output supports reliable production control and seamless data capture. Benefit from a compact, micro‑range design that delivers repeatable external measurements; order directly via Metav Werkzeuge or contact our consultants for application advice. Digital micrometer M302.077 — 75–100 mm, 0.001 mm resolution (Metav IndustryLine) The Digital micrometer M302.077 is a precision external measuring instrument designed for fine mechanical workshop and inspection use, offering high‑resolution readings and digital data output for process integration. 0.001 mm reading precision Friction ratchet for consistent force RB 6 data output for traceable records Compliant with DIN 863 High precision where tight tolerances matter The instrument delivers 0.001 mm resolution on a 75–100 mm measuring span, enabling confidence in tight tolerance checks and finish control. The fine display resolution converts to practical gains at the inspection bench: shorter checking cycles and fewer manual adjustments. The friction ratchet ensures a consistent measuring force, reducing operator‑dependent variation and improving repeatability over multiple parts. For tasks that require verified external measurements, this micrometre gauge offers a measurably superior basis for decision‑making. Ergonomics and handling that reduce error A thoughtfully proportioned frame and tactile ratchet make the tool straightforward to operate during repetitive checks; the controlled feel of the ratchet avoids over‑tightening that distorts readings. The measuring faces of 6.5 mm diameter provide a stable contact area while keeping the tip profile compact for small features. Weighing around 1.3 kg, the unit balances solidity and workshop practicality: it is robust enough for frequent use yet still manageable for single‑person handling during standard inspection routines. Digital integration for efficient data capture Equipped with an RB 6 data output, the electronic readout supports direct transfer of measurements to logging systems or SPC software, cutting transcription time and reducing clerical errors. The digital display includes ON/OFF/SET/DATA/mm/inch/0 functions to simplify zeroing and unit changes at the bench. Where traceability and documented measurement records are required, this instrument enables straightforward capture of values without interrupting production flow. Built for routine use and workshop longevity Construction meets DIN 863 expectations for micrometres, and hardened measuring faces increase wear resistance under regular use. The instrument is supplied in a protective case for safe transport and storage, guarding calibration and accuracy between uses. Classified in the micro range for external gauges, the design supports fine mechanical and inspection tasks commonly found in toolmaking, maintenance and quality control environments. Contact Metav Werkzeuge for application guidance and to arrange supply of the Metav IndustryLine digital micrometer M302.077 with 0.001 mm resolution and RB 6 output; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M302.077 GTIN: 4054469168821 Category: Micrometres Facts Measuring range: 75–100 mm Resolution / reading: 0.001 mm Measuring faces: 6.5 mm Weight: 1.3 kg Tariff number: 90173000 Special features Digital display with ON/OFF/SET/DATA/mm/inch/0 functions Friction ratchet for reproducible measuring force RB 6 data output for direct data transfer Hardened measuring faces for wear resistance Supplied in protective case Conforms to DIN 863 FAQ Is the micrometer suitable for precision workshop checks on small parts? Yes. The Metav IndustryLine digital micrometer M302.077 operates in the micro range (75–100 mm) and, with its 0.001 mm resolution and friction ratchet, is intended for fine external measurements typical in precision workshops. Can measurements be exported to a data collection system? The unit includes an RB 6 data output, enabling direct transfer of readings from the digital micrometer M302.077 to compatible logging or SPC systems for streamlined documentation. How does the friction ratchet improve measurement reliability? The friction ratchet provides a controlled final torque when closing the spindle, which standardises the measuring force and reduces operator‑related variability in repeated checks with the digital micrometer. Are the measuring faces durable for regular use? The measuring faces on this micrometre are hardened and have a 6.5 mm contact diameter, offering enhanced wear resistance suitable for routine inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75–100mm Three-Point Disc Micrometer Ø30mm Disc, Painted Frame, Matt Chrome Drum, Ratchet, Boxed - Metav IndustryLine
Take advantage of a compact disc micrometre that combines a practical 75–100 mm measuring range with a fine accuracy of ±0.005 mm and a ratchet stop for repeatable contact force — supplied ready for safe transport in a protective case. Order directly via Metav Werkzeuge or consult their specialists for procurement and technical advice. Disc micrometre M309.353 — Analog micrometre, 75–100 mm, Ø30 mm disc The Disc micrometre M309.353 is an analog workshop micrometre designed for precise linear measurements in metalworking and mechanical assembly, offering a standard-range solution for routine and quality-control tasks. Measuring range 75–100 mm Ø30 mm disc measuring faces Accuracy ±0.005 mm Ratchet stop for consistent measuring force Consistent repeatability for workshop measuring routines The micrometre is built around a proven mechanical design that prioritises repeatable measurements in production and inspection. The integrated ratchet stop limits applied torque, reducing operator-induced variation and supporting reproducible contact pressure. With an accuracy of ±0.005 mm (5 µm), the instrument meets tighter workshop tolerances than common industrial nonius gauges, making it well suited for demanding fits and precision assemblies while remaining straightforward to read and interpret. Disc measuring faces for delicate and curved surfaces Equipped with Ø30 mm disc measuring faces, this model spreads contact pressure over a larger area compared with point anvils. That geometry helps to avoid local indentations when measuring softer materials or parts with slight curvature, and it improves alignment on short contact paths. The non-rotating spindle protects the workpiece surface during measurement and reduces the risk of scoring, which supports serviceable longevity of both the instrument and sensitive components. Robust finish and ergonomic handling for daily use The frame is lacquered for corrosion resistance and the thimble is matt-chrome plated to reduce glare and provide a durable, tactile surface for adjustment. At approximately 1.1 kg the tool offers a solid feel that aids stable handling without being cumbersome. The analogue scale keeps the instrument simple to operate, with familiar mechanical feedback that many machinists and inspectors prefer for quick checks and bench use. Integration into the workshop and transport-ready delivery Classified in the Standard range (maximum 100 mm), this micrometre complements 150/200/300 mm base tools commonly used in mechanical workshops, providing an efficient balance of reach and stiffness. The instrument is supplied in a protective transport case to safeguard the measuring faces and mechanism during storage and transit. Its straightforward mechanical design makes maintenance straightforward and ensures long service life when handled correctly. Choose Metav IndustryLine's disc micrometre M309.353 for reliable 5 µm accuracy and workshop-proven repeatability — contact Metav Werkzeuge for ordering and specialist advice from Emmerich. Technical data Article number: M309.353 GTIN: 4054469118802 Category: Messschrauben (micrometres) Label: Teller-Mess, ND, 75 - 100 mm, Ø 30 mm Teller Facts Measuring range: 75–100 mm Accuracy: ±0.005 mm Disc diameter: Ø 30 mm Weight: 1.1 kg Reading: analog (mechanical) Special features Lacquered frame Matt-chrome thimble Ratchet stop Non-rotating spindle Delivered in a transport case Suitable for workshop and inspection use FAQ What measuring range does the micrometre cover? The Disc micrometre M309.353 covers a 75–100 mm range, placing it in the standard workshop class for medium‑sized components. How precise is the instrument for quality-control tasks? The instrument offers an accuracy of ±0.005 mm, which is suitable for fine mechanical assemblies and reproducible inspection steps. Are the measuring faces suitable for delicate surfaces? Yes, the Ø30 mm disc measuring faces distribute contact pressure and, together with the non-rotating spindle, reduce the risk of surface marking on softer materials. Does the micrometre provide consistent contact pressure? The built-in ratchet stop ensures repeatable measuring force, improving measurement consistency across operators and cycles. Is the instrument supplied ready for transport? The micrometre is supplied in a protective transport case, which secures the instrument for storage and movement between workstations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
775mm Setting Gauge For Micrometers With Heat Shield, Accuracy ±0.008mm Ball Contact - Metav IndustryLine
Take advantage of high reproducibility and user-friendly handling with a 775 mm setting gauge that combines ±0.008 mm accuracy and thermal protection for stable micrometer adjustment; order directly via Metav Werkzeuge or consult the team for application-specific advice. M304.321.2 — 775 mm setting gauge for outside micrometers with heat protection M304.321.2 is a precision setting gauge designed to set and verify outside micrometers in production and inspection environments, offering a long measuring range with features that reduce thermal and contact-related measurement errors. 775 mm nominal length High accuracy ±0.008 mm Ball-shaped measuring faces Integrated heat protection Precision that remains consistent over long spans The setting gauge delivers a ±0.008 mm accuracy across its 775 mm nominal length, which makes it suitable where reproducible reference values are required for micrometer adjustment. The ball measuring faces reduce local deformation at the contact points and simplify centring on cylindrical parts, while the solid 16 mm diameter shaft contributes to structural stability. With a mass of 1.3 kg, the unit resists inadvertent movement during setup, translating into fewer re-measurements and a more efficient calibration routine. Designed for workshop and production environments Classified as a large-range (500–1,000 mm) setting instrument, this gauge is intended for use in machine shops, fixture assembly and quality-control benches where extended reach and stiffness are both required. The tool functions as a straightforward reference for setting outside micrometers and is particularly helpful when working with longer spindles, jaws or large workpieces that exceed typical bench gauges. The nominal geometry and handling characteristics reduce the time needed for micrometer adjustment and help maintain process throughput. Built-in thermal protection and trusted provenance Thermal effects are a common source of drift in dimensional work; the integrated heat protection minimises influence from operator contact and ambient temperature fluctuations, supporting stable settings across shifts. Supplied with ball-shaped contacts to limit local distortion, the instrument supports repeatable results during serial setups. As part of the Metav IndustryLine, the gauge benefits from an established European supply chain that focuses on accessible precision and dependable delivery, reinforcing reproducibility at the workshop level. Contact Metav Werkzeuge for tailored advice on using the Metav IndustryLine 775 mm setting gauge and to discuss delivery options from Emmerich. Technical data SKU: M304.321.2 GTIN: 4054469116808 Manufacturer: Metav IndustryLine Facts Nominal length: 775 mm Accuracy: ±0.008 mm Diameter: 16 mm Weight: 1.3 kg Special features Ball-shaped measuring faces Heat protection Tariff number: 90173000 Category: Accessories — measurement equipment FAQ What is the nominal length of this setting gauge? The setting gauge has a nominal length of 775 mm and is listed as SKU M304.321.2 in the Metav IndustryLine. What accuracy can be expected when using the gauge? The instrument provides an accuracy of ±0.008 mm, enabling precise setting of outside micrometers. Which micrometers is the gauge intended to set? It is designed as a setting gauge for outside micrometers and is suitable for workshop and production adjustment tasks. Does the gauge reduce thermal and contact-related errors? Yes, the model incorporates heat protection and uses ball-shaped measuring faces to minimise thermal drift and local contact deformation. Which measurement-range class does this instrument belong to? The gauge falls into the large-range class (500–1,000 mm), making it suitable for larger components and fixtures where extended reach and stiffness are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
7x Pair Universal Measuring Attachments Flat Round Disc Cutting Point Thin Blade Edge - Microtech Metrology
Take advantage of a compact, versatile accessory set that expands measuring capability with seven pairs of tip geometries, optimised for universal outside micrometers; the combination of variety and precise contact surfaces supports efficient measurement workflows. Order or request advice via Metav Werkzeuge for fast procurement and application support. Universal Measuring Attachment Set — 7 pairs for universal outside micrometers by Microtech Metrology Universal Measuring Attachment Set is a compact accessory kit designed to adapt universal outside micrometers for a wide range of contact geometries in workshop and laboratory environments. Seven pairs of tip geometries Compatible with universal outside micrometers Precision contact surfaces for repeatable readings Versatile set for inspections and small-batch metrology Extend measurement reach with tailored tip geometries The set supplies seven pairs of interchangeable contacts—flat, round, disc, cutting edge, pointed, thin and knife‑edge—so standard micrometers can be adapted quickly for specific tasks. By replacing the contact face rather than switching instruments, inspection loops remain short and cycle times are reduced. The variety of tip shapes supports precise positioning on shafts, edges, recesses and thin webs, improving repeatability and reducing setup time in series inspection. Improve workflow reliability with consistent contact surfaces Each attachment is produced for consistent contact behaviour, which helps to minimise operator‑dependent variation when measuring. Where surface form or access is challenging, the nominal contact geometry determines the contact area and pressure distribution; selecting the correct tip reduces measurement error and preserves the reference standard. The result is a measurable uplift in quality assurance efficiency and fewer rejected parts due to ambiguous readings. Simple handling and clear inventory for the workshop The set groups seven distinct contact pairs in one delivery, making it straightforward to maintain an inventory of common geometries for micrometer testing and part verification. Compatibility with universal outside micrometers means there is no need for tool‑specific conversion kits. Clear labelling of each pair speeds selection during bench checks and helps standardise measurement procedures across shifts and operators. Contact Metav Werkzeuge to request the Microtech Metrology Universal Measuring Attachment Set (SKU 110750100) or to discuss the right tip choice for specific applications; Metav Werkzeuge is available at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice Technical data Article number: 110750100 GTIN: 4061905458392 Manufacturer: Microtech Metrology Facts Pairs in set: 7 Items per set: 7 pairs Special features Flat, round, disc, cutting edge, pointed, thin, knife‑edge contacts Suitable for universal outside micrometers Accessory for measurement and inspection tasks FAQ Which micrometers are compatible with these attachments? The attachments are designed for use with universal outside micrometers; compatibility is confirmed for standard thread mountings and contact adaptors used in bench micrometers supplied by Microtech Metrology (SKU 110750100). What contact geometries are included in the set? The set contains seven pairs: flat, round, disc, cutting edge, pointed, thin and knife‑edge, supplied to extend the functionality of universal outside micrometers for varied measurement tasks. Can the attachments affect measurement accuracy? Attachments alter the contact geometry and therefore the contact area; using the correct tip from the Microtech Metrology set helps to reduce measurement variability and improve the repeatability of readings with universal outside micrometers. Is this set suitable for in‑process inspection on production lines? Yes. The array of contact types in the Microtech Metrology set makes it suitable for rapid changeover during short inspection cycles and for small‑batch quality checks where different part geometries occur. How many pieces are supplied in one set? One set contains seven pairs of measuring attachments (total seven pairs), referenced under SKU 110750100. Microtech Metrology: Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
Precision micrometers built for repeatable accuracy
Micrometers—also referred to as micrometer screw gauges or micrometer callipers—are compact, robust instruments for fast, highly accurate length measurement of small to medium workpieces. Designed for routine use on the shop floor, these tools combine mechanical reliability with options for digital data capture, making them indispensable where repeatable tolerances matter.
How micrometers work and where they belong in production
Micrometers operate on a finely threaded spindle that brings two measuring faces into alignment with the workpiece; many designs follow the Abbe comparator principle so that the measuring axis and scale are collinear, reducing tilting errors. Typical outside micrometers (bühlermessschrauben) provide readings down to 1/1000 mm (0.001 mm) in analogue form; internal micrometers and specialised two- or three-point gauges enable accurate diameter and bore measurements, while depth micrometers cover depths from 0–300 mm. Hardened carbide (HM) measuring faces are standard to prevent wear and maintain accuracy over time. Digital variants offer easy reading, unit switching (mm/inch) and data output via USB, RS interface or Bluetooth; advanced models with an integrated minicomputer support Go/NoGo checks, temperature compensation and wireless transmission up to 50 m.
Practical benefits that improve shop‑floor performance
- Reduced rework and higher first-pass yield thanks to repeatable accuracy and carbide-tipped measuring faces.
- Faster, safer measurement cycles by using the ratchet/coupling to limit measuring force to 5 N to 10 N, protecting both part and instrument.
- Flexible inspection workflows with analogue, digital and minicomputer options, including wireless data transfer and mm/inch toggle.
- Versatile coverage with outside, internal, depth and built-in micrometers offering measuring ranges from a few millimetres up to 300 mm and resolution down to 2 µm (internal) or 0.003 mm (standard depth micrometers).
- Durable operation in workshop environments: mechanical models resist dust and moisture, while digital versions are available with IP54 protection.
Metav — a precision partner you can rely on
Metav combines decades of technical expertise with a broad, quality-filtered product range from its Emmerich hub. Over 48,000 customers trust Metav’s offer of more than 250,000 products, which simplifies procurement and secures reliable supply for industry, trade and specialist retailers. For buyers seeking micrometers with consistent performance and traceable data capture, Metav’s selection and technical support make it a practical, long-term choice.
In short
Micrometers provide robust, highly repeatable measurement for external, internal and depth applications, available in analogue, digital and minicomputer formats to match precision requirements and data‑management needs.
FAQ
How precise are micrometers for internal measurements?
Internal micrometers in the micrometers category can achieve accuracies around 2 µm when correctly used; digital and minicomputer models improve readout convenience and data integration for traceable inspection results.
When is a digital micrometer preferable to an analogue one?
Choose a digital micrometer when easy readout, unit conversion (mm/inch), or data transmission is required. Digital models with IP54 rating also offer dust and splash protection, while analogue micrometers remain the most robust option in harsh environments.
What measuring force should be used to ensure consistent results?
The recommended measuring force for micrometers is 5 N to 10 N. Use the ratchet or friction thimble to apply this consistent force and rely on the insulating sleeve to minimise heat transfer from the hand.
Can depth micrometers measure small bores and tight features?
Yes. Depth micrometers use a fine needle or flat measuring face and, with suitable extensions, cover narrow or deep features; standard depth micrometers typically span 0–300 mm with accuracies near 0.003 mm, while specialised digital systems offer even higher resolution.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com