Gibt es einen Hahn und Kolb Online Shop?

Benefit from the combination of robust rigidity and precise geometry: the holder provides a 90° cutting angle, an effective 125 mm diameter and eight cutting edges for stable shoulder operations; procure the item via Metav Werkzeuge or consult the specialists for integration support. Corner tool head T430TM — indexable insert holder, 125 mm diameter, 90° cutting angle (Teknik Makina) Corner tool head T430TM is an indexable insert holder engineered for turning and face operations, intended for use with R390-1806 indexable inserts in demanding production environments. 125 mm diameter for wide-reaching cuts 90° cutting angle for precise shoulder cuts 40 mm shank diameter for secure clamping Compatible with Sandvik R390-1806 inserts High rigidity for consistent, high-quality cuts The design delivers a predictable cutting geometry based on a 90° cutting angle, which helps maintain dimensional consistency when forming shoulders or square features. The large 125 mm head diameter and the distribution of eight cutting edges increase stability and reduce vibration during interrupted cuts. Such geometry is especially useful in batch production where repeatability matters; users benefit from fewer reworks and improved cycle-time stability thanks to the holder's mechanical stiffness and balanced load distribution. Straightforward mounting and secure clamping for quick tool changes Installation relies on standard fastenings and a robust clamping interface: the holder uses a M4x11 Torx screw tightened with a T15 key, and presents a 40 mm shank diameter for firm seating in common tool posts or turrets. This configuration permits fast, reproducible set-ups and reduces downtime during insert changes or re-indexing. The straightforward fixing method is compatible with common workshop workflows, enabling maintenance teams to swap inserts and resume machining with minimal adjustment effort. Engineered compatibility and dependable weight-to-rigidity ratio Designed specifically for R390-1806 indexable inserts from Sandvik, the tool head integrates with established insert geometries to exploit chip control and edge life. The component's mass of 3.558 kg and compact overall length of 62 mm contribute to a favourable rigidity-to-overhang balance, supporting heavier cuts without excessive deflection. Specified tolerances and the selection of fastening hardware provide a basis for long-term reliability in series production or demanding single-part manufacture. For specification checks, fixture compatibility or to arrange procurement of the Teknik Cutting Tools corner tool head T430TM for Sandvik R390-1806 inserts, contact Metav Werkzeuge and benefit from expert advice and supply from Emmerich. Technical data Article number: T430TM Manufacturer: Teknik Makina Product name: Corner tool head Designation: for R390-1806 Indexable Inserts Compatible insert manufacturer: Sandvik Facts Weight: 3.558 kg Shank diameter: 40 mm Head diameter: 125 mm Number of cutting edges: 8 Overall length: 62 mm Cutting angle: 90° Special features Torx screw: M4x11 Torx key: T15 Fits R390-1806 indexable inserts Robust holder design for shoulder operations FAQ Which inserts are compatible with this holder? The corner tool head T430TM is designed for use with R390-1806 indexable inserts and is listed as compatible with Sandvik insert geometries. What fastening hardware is required for mounting? Mounting uses an M4x11 Torx screw and requires a T15 key; these specifications are standard for the T430TM and ensure secure clamping. What shank diameter is required in the tool post? The T430TM has a 40 mm shank diameter, which should be matched by the machine's tool holder or adapter to achieve correct seating and rigidity. How many cutting edges does the head provide and what is the benefit? The holder features eight cutting edges; this distribution enhances stability and aids in even wear distribution during shoulder machining. What are the dimensional attributes to consider for fixture planning? Key dimensions for planning are the 125 mm head diameter, overall length of 62 mm and the 40 mm shank diameter of the T430TM; these values guide clearance and overhang calculations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a stable 90° cutting geometry and broad compatibility with LNMX 1510 indexable inserts for reliable shoulder machining; the robust 40 mm shank and Ø125 construction ensure secure clamping and steady cuts. Order directly via Metav Werkzeuge or contact their consultants for specification support. Corner Turning Head T380TM — for LNMX 1510 indexable inserts, 90° cutting angle (Teknik Makina) A robust Corner Turning Head T380TM designed for precise shoulder and form turning in conventional lathe applications with LNMX 1510 indexable inserts 90° cutting angle for shoulder machining Compatible with LNMX 1510 indexable inserts 40 mm shank diameter for secure clamping Torx M4x12.5 fastening, key T15 Consistent shoulder profiles with defined 90° geometry The 90° cutting geometry provides a repeatable machining stance for shoulder faces and square shoulders, reducing secondary operations and setup time. With support for LNMX 1510 indexable inserts, the turning head delivers a cost-effective solution through rapid indexability; worn edges are rotated rather than replaced, which improves process economy. This arrangement suits mixed-batch production where predictable edge positioning and fast reconditioning matter. Stable clamping for vibration reduction and tool life A 40 mm shank diameter and substantial Ø125 head diameter combine to provide rigidity at the toolpost, which lowers vibration and improves surface finish. The tool head uses a Torx M4x12.5 fastening and T15 key specification for secure insert retention, simplifying maintenance and repeatable reassembly. The solid design, with an overall length of 63 mm and a mass of 3.65 kg, contributes to steadier cutting conditions and reduced risk of chatter in medium-duty turning operations. Broad compatibility eases tool sourcing and inventory Designed for LNMX-format inserts, the head accepts inserts from major manufacturers (ISCAR, Korloy, LMN, YG-1), enabling flexibility in procurement and the use of preferred grades and coatings. The tool head supports indexable inserts with multiple cutting edges—this reduces overall tooling cost per part in production environments where indexed reuse is standard. Integration into existing toollines is straightforward thanks to familiar insert geometry and clamping conventions. Quick maintenance and reliable integration into production Routine service is straightforward: the Torx fastening is industry-standard, and insert changes are fast, letting operators return to machining with minimal downtime. The head’s dimensions and fastening pattern align with common toolholder setups, facilitating rapid adoption without elaborate adapters. For production managers, this means higher machine uptime and a predictable maintenance cadence, supporting continuous operation and planning. Discuss technical integration and order options with Metav Werkzeuge—call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored advice on the T380TM corner turning head Technical Data Article number: T380TM Manufacturer: Teknik Makina Designation: Corner turning head for LNMX 1510 indexable inserts Data Diameter: 125 mm Shank diameter (aufnahme): 40 mm Overall length: 63 mm Weight: 3.65 kg Cutting angle: 90° Number of cutting edges: 10 Torx screw: M4x12.5 Special features Compatible with LNMX 1510 indexable inserts Suitable insert manufacturers: ISCAR, Korloy, LMN, YG-1 Torx key size: T15 ECLASS: 21181015 FAQ What insert type does the tool head accept? The turning head accepts LNMX 1510 indexable inserts and is compatible with inserts from ISCAR, Korloy, LMN and YG-1. Is the fastening hardware standardised? Yes. The head uses a Torx M4x12.5 fastening with a T15 key specification for secure clamping. What are the key dimensions for machine setup? Key dimensions are Ø125 mm head diameter, 40 mm shank diameter and 63 mm overall length, which should be checked against the toolpost clearance. How does the 90° cutting angle benefit production? A 90° cutting angle ensures consistent shoulder profiles and simplifies alignment for square shoulder and face turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact design that combines a rigid ISO 1616 shank with a 125 mm overall length for stable, repeatable parting operations; compatibility with ISCAR inserts ensures straightforward insert changes and continuity in production. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Parting tool holder D063TM — 125 mm, ISO 1616, left-hand, Teknik Makina A Parting tool holder D063TM engineered for left-hand parting operations, offering a compact ISO 1616 shank for secure clamping and precise groove formation in workshop and production environments. ISO 1616 shank size 125 mm overall length Left-hand cutting direction Compatible with ISCAR inserts Consistent rigidity for accurate parting results The compact shank geometry and narrow profile of this holder deliver stable clamping and reduced vibration during parting, which translates into improved surface quality and extended insert life. The ISO 1616 specification (16 × 16 mm) ensures a precise fit with standard tool posts, while the 125 mm overall length keeps the tool projection minimal, reducing lever forces and supporting repeatable set-ups in batch production. This combination supports efficient machining with fewer rework cycles and predictable results. Straightforward insert changes and secure fastening Designed to work with established insert systems, the holder accepts ISCAR indexable inserts and uses a Torx T15 key for quick and reliable clamping. The fixing screw is M4×12.5, enabling firm retention of the cutting edge while allowing rapid exchange during shift changes. These mechanical details reduce downtime for tool changes and simplify workshop logistics: common service tools and replacement screws are compatible with the holder, making maintenance predictable and fast. Optimised for focused parting and grooving tasks With a maximum allowable parting depth of 16 mm and a cutting-edge width of 2 mm, the holder is tailored for narrow-groove and part-off operations where precision is essential. The left-hand cutting orientation suits setups that require the cutter to feed from the right towards the workpiece centre, ensuring the correct chip flow and feed direction for stable machining. The tool’s geometry supports reproducible cuts and contributes to consistent cycle times on turned components. Practical handling and identification for workshop use Weighing approximately 0.267 kg and featuring a cutting-head width of 16.2 mm, the holder balances durability with manageable handling during set-up and inspection. The compact mass aids quick repositioning and reduces operator fatigue when changing tools in confined toolpost arrangements. For identification and order reference the item is listed under SKU D063TM, which streamlines procurement and inventory control in production environments. Contact Metav Werkzeuge for tailored application advice and secure supply of Teknik Cutting Tools parting holders; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility and lead times Technical Data Article number: D063TM Product type: Parting tool holder Brand: Teknik Makina Cutting direction: left Facts Overall length: 125 mm Shank size: 16 × 16 mm (ISO 1616) Weight: 0.267 kg Max parting depth: 16 mm Cutting edge width: 2 mm Cutting-head width: 16.2 mm Special features Compatible with ISCAR inserts Torx key: T15 Fixing screw: M4x12.5 FAQ Which insert families fit this holder? The holder accepts ISCAR indexable inserts designed for parting and grooving; compatibility is ensured by the holder’s geometry and clamping arrangement for common ISCAR shapes. Is the shank compatible with standard tool posts? Yes, the 16 × 16 mm (ISO 1616) shank secures in standard tool post clamps and provides a repeatable datum for accurate positioning. What is the maximum cutting depth achievable? The tool supports a maximum parting depth of 16 mm, suitable for narrow-groove and part-off operations within that range. How is the insert fastened and serviced? Insert clamping uses a Torx drive; a T15 key and an M4×12.5 screw enable secure fastening and straightforward insert replacement. How should this holder be referenced when ordering? Order using SKU D063TM; mentioning the brand Teknik Makina and the ISO 1616 shank helps ensure the correct variant is supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a compact 125 mm overall length with a 20 mm clamping width and compatibility for DCEN 300 indexable inserts, this grooving clamping holder delivers stable, right-hand parting performance and consistent insert life. Available through Metav Werkzeuge for secure supply and technical advice. Grooving clamping holder DCEN 300 L125mm — for DCEN 300 indexable inserts, right-hand, ISO 2020 (Teknik Makina) The Grooving clamping holder DCEN 300 L125mm is a right-hand toolholder engineered for secure parting and grooving operations with DCEN 300 indexable inserts in industrial turning applications. *125 mm overall length *20 mm clamping width *Compatible with DCEN 300 indexable inserts *Right-hand cutting direction *Includes 3 mm Allen key Greater stability for precision parting and longer insert life The holder’s compact design and 20 mm clamping width provide a stiff interface between insert and machine, reducing micro-movement during cuts. This rigidity translates into improved surface finish and more predictable tool life, which supports higher first-pass yields in production settings. The ISO 2020 designation ensures a standardised connection profile for repeatable clamping, and the measured mass of 0.409 kg gives a good balance between robustness and manoeuvrability for machining set-ups. Fast setup and broad compatibility to save cycle time Designed for DCEN 300 indexable inserts, the toolholder accepts widely used grooving inserts and is listed as compatible with ISCAR tooling, simplifying procurement and inventory management. The right-hand orientation and a maximum cutting depth of 22 mm enable confident parting and grooving to common workpiece geometries, while the 3 mm Allen key supplied eases initial mounting and insert changes. Clear, measurable specifications—such as the 3 mm cutting-edge width—help to plan cutting parameters and coolant strategies without guesswork. Robust workmanship for workshop reliability Constructed for the demands of daily production, this clamping holder is intended to withstand consistent use while keeping servicing straightforward. The defined cutting head width of 20 mm and matching clamping dimensions reduce the need for frequent tool swaps, lowering downtime. As part of a coordinated tooling strategy from a recognised tooling supplier, the holder supports efficient tool inventory and dependable machining quality in small to medium series production. For precision right-hand grooving with DCEN 300 inserts from Teknik Makina, contact Metav Werkzeuge in Emmerich for expert advice and reliable delivery. Technical data Article number: D744TM Product type: Grooving clamping holder Brand: Teknik Makina Facts Overall length: 125 mm Weight: 0.409 kg Clamping width: 20 mm Clamping height: 20 mm Cutting head width: 20 mm Max cutting depth: 22 mm Cutting-edge width: 3 mm Special features Compatible with DCEN 300 indexable inserts (ISCAR) Right-hand cutting direction ISO 2020 designation Includes 3 mm Allen key FAQ Which inserts fit this holder? The holder is manufactured for DCEN 300 indexable inserts and is listed as compatible with ISCAR DCEN 300 styles. Is the toolholder suitable for right-hand or left-hand cutting? This toolholder is specified for right-hand cutting direction and is optimised for right-hand parting and grooving tasks. What is the maximum parting depth? The maximum cutting depth for the holder is 22 mm, matching common grooving operations and allowing planning of cut passes accordingly. Which designation and mounting standard does the holder use? The holder follows ISO 2020 dimensions for the clamping interface, ensuring a standardised fit and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah. 422 Nolu Sokak No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Taking advantage of a compact 125 mm profile combined with a standard 20 × 20 mm shank and a 30° cutting angle provides stable, space-saving clamping for routine turning operations; order via Metav Werkzeuge or consult our advisors for integration support. Clamp Holder L125mm — Toolholder with 20 × 20 mm shank and 30° cutting angle by Teknik Makina The Clamp Holder L125mm is a compact toolholder designed to deliver secure clamping and consistent positioning for workshop lathes and turning stations. Clamp holder L125 mm by Teknik Makina 20 × 20 mm shank for standard toolposts 30° cutting angle for controlled chip flow Robust 0.424 kg construction for stability Space-saving length that suits confined toolposts With an overall length of 125 mm, this toolholder is engineered for installations where space is limited yet repeatability is critical. The reduced footprint enables closer tool spacing on the turret or carriage without compromising rigidity. A compact profile coupled with the 20 × 20 mm shank simplifies retrofitting into standard toolposts, while the mass of 0.424 kg contributes to vibration damping and steadier cutting conditions. The result is predictable performance and fewer interruptions for repositioning. Consistent clamping for repeatable machining results The design focuses on secure clamping to maintain axial and radial position throughout the cut, reducing the need for frequent re-adjustment and improving part-to-part consistency. The incorporated 30° cutting angle supports controlled chip direction and can aid in managing cutting forces for many turning tasks. As a standardised toolholder, the unit helps streamline setup routines, allowing production sequences to remain efficient and less error-prone. Built to integrate smoothly into workshop workflows Manufactured by Teknik Makina and identified as P094TM, this holder is suitable for typical lathe setups where a balance of size and stability is required. The moderate weight and compact form factor make handling straightforward during tool changes, and the standard dimensions mean fewer custom adaptors are needed. This practical combination reduces overall setup time and contributes to a steadier production rhythm on the shop floor. Standard designation and straightforward specification for planners The ISO-related designation 2020 corresponds to the shank dimensions and helps purchasers and planners verify compatibility with existing fixtures and toolposts. Clear numerical data—length, shank size, cutting angle and mass—allow precise integration planning and support procurement decisions where interchangeability and standardisation are priorities. The concise specification aids technical documentation and ensures compatibility checks can be completed quickly. For robust clamping from Teknik Makina (SKU P094TM) and tailored advice on integrating this clamp holder into existing equipment, contact Metav Werkzeuge for reliable supply and technical guidance from our Emmerich centre. Technical data Article number: P094TM Label: Klemmhalter L125mm Manufacturer: Teknik Makina Facts Overall length: 125 mm Shank width: 20 mm Shank height: 20 mm Cutting angle: 30° Weight: 0.424 kg Special features ISO designation: 2020 Product type: Clamp holder EClass: 21181004 UID / SKU: P094TM FAQ What is the overall length of the clamp holder? The Clamp Holder L125mm (P094TM) has an overall length of 125 mm, suitable for compact lathe setups. Which shank dimensions does this holder use? The toolholder is specified for a 20 × 20 mm shank (ISO designation 2020), matching many standard toolposts. What is the intended benefit of the 30° cutting angle? A 30° angle supports controlled chip flow and helps manage cutting forces, contributing to steadier cutting conditions with the clamp holder. Can this holder be identified for procurement and documentation? Yes — the holder is listed under SKU P094TM and carries the label Klemmhalter L125mm for clear ordering and stock control. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid clamping, a compact 125 mm reach and defined 30° geometry for consistent turning results; order the tool directly via Metav Werkzeuge or consult our specialists for integration advice. Klemmhalter L125mm — Clamping holder with 125 mm reach and 20 × 20 mm shank The Klemmhalter L125mm is a robust clamping holder engineered for turning applications, compatible with 20 × 20 mm tool shanks and designed to provide stable tool support in confined setups. 125 mm overall length for extended reach Compatible with 20 x 20 mm tool shanks 30° cutting-angle geometry for access Stable, compact construction for rigidity Increased process reliability through rigid clamping A rigid tool mounting reduces vibration and improves surface finish; the clamping holder’s solid construction and compact footprint deliver that stability. The 125 mm length offers reach without excessive overhang, while the 20 × 20 mm contact area provides a secure fit for standard square shanks. These attributes translate into fewer interruptions in production and more consistent part quality, especially where tight tolerances are required. Emphasis on mechanical stability supports higher cutting performance and predictable tool life. Geometry that supports efficient turning strategies The defined 30° cutting angle optimises tool approach for many turning operations, allowing better access on profiles and shoulders. By combining this geometry with a compact body, the holder enables effective chip flow and reduces the need for repeated tool changes in constrained setups. For workshops seeking measurable improvements in cycle time, the shaped geometry contributes to more efficient material removal and fewer adjustments at the machine, which can lower setup time and increase throughput. Practical specifications for integration and inventory control Clear dimensional data simplifies selection and stocking. With an overall length of 125 mm, a width of 20 mm and a height of 20 mm, plus a mass of 0.424 kg, the component is straightforward to compare with existing holders and tool carriers. The ISO-related designation 2020 indicates compatibility with common 20 × 20 mm arrangements, aiding purchasing decisions and spare-part planning. Such transparent specifications make planning for toolrooms and small-series production more predictable and reduce the risk of mismatched components. Durable choice from a recognised manufacturer Produced by Teknik Cutting Tools, the holder combines a compact design with manufacturing standards geared to repetitive industrial use. The product’s measured weight and dimensions reflect a balance between stiffness and serviceability, making it suitable for general turning tasks where reliable clamping is essential. For operations that prioritise steady seating and low-maintenance mounting, the holder offers a pragmatic option that integrates readily into established workflows. For reliable turning performance choose Teknik Cutting Tools’ clamping holder with a 125 mm reach and 30° geometry — order via Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for technical matching and delivery options. Technical data Article number: P096TM Product type: Clamping holder Brand: Teknik Cutting Tools Specifications Overall length: 125 mm Width: 20 mm Height: 20 mm Weight: 0.424 kg Cutting angle: 30° Designs / Special features ISO designation: 2020 Compatible shank size: 20 × 20 mm Compact, rigid construction Suitable for turning tool mounting FAQ What shank size is compatible with this holder? The clamping holder accepts a 20 × 20 mm tool shank (ISO designation 2020), ensuring compatibility with standard square shank tooling. What is the overall length and how does it affect reach? Overall length is 125 mm; this provides an extended but controlled reach that balances access with reduced overhang for improved rigidity. What is the specified cutting angle and why does it matter? The holder features a 30° cutting-angle geometry, which improves access for shoulder and profile turning and supports more efficient chip evacuation. How heavy is the unit and what does that imply for mounting? Weight is 0.424 kg; the moderate mass contributes to a stable mounting without excessive load on the toolpost or turret. Who manufactures this clamping holder and what is the SKU? The holder is produced by Teknik Cutting Tools and listed under SKU P096TM for ordering and inventory purposes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Taking advantage of the 125 mm overall length, the 20 x 20 mm square shank and the 30° cutting angle enables compact installation and controlled chip flow for stable machining cycles; order the clamp directly via Metav Werkzeuge or consult the Metav advisors for application support. Clamping holder P091TM — compact tool holder with 20 x 20 mm shank The clamping holder P091TM is a compact tool holder designed for turning and related machining tasks where a short overall length and a square 20 × 20 mm shank are required. 125 mm overall length 20 x 20 mm square shank 30° cutting angle Space-efficient design for constrained toolposts The short 125 mm overall length reduces overhang and helps maintain rigidity in confined set-ups, which in turn supports more consistent surface finishes and extended tool life. A reduced projection lessens vibration amplitude and enables higher effective cutting parameters at the same machine settings. The compact footprint is particularly beneficial for workshop benches and smaller lathes where available clearance is limited. Secure mounting and predictable clamping behaviour The 20 x 20 mm square shank provides a standard interface for many toolposts and quick-change systems, delivering reliable seating and repeatability during index and tool change operations. The square profile simplifies alignment and prevents rotation under load, making the holder well suited to tasks that demand consistent geometry. Clear mechanical fit reduces set-up time and minimises the need for secondary adjustment. Optimised engagement for controlled cutting A 30° cutting angle supports a balance between chip formation and flank contact, enabling controlled material removal for a wide range of turning operations. This geometry helps to direct cutting forces and chip flow, which can reduce tool pressure peaks and contribute to smoother machining. The result is a predictable machining process that aids in maintaining dimensional tolerances in serial production. Workshop logistics and practical handling With a mass of 0.424 kg, this tool holder is light enough for straightforward handling while remaining robust for daily use. The ISO designation 2020 indicates a standardised format for shank geometry, simplifying replacement logistics and inventory management. The compact, standardised format also supports centralised procurement and quicker stocking decisions within service or production departments. For procurement of Teknik Makina clamping holders and for technical advice, contact Metav Werkzeuge for prompt delivery from Emmerich and tailored application guidance via info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: P091TM Label: Klemmhalter L125mm Manufacturer: Teknik Makina Facts Overall length: 125 mm Shank width: 20 mm Shank height: 20 mm Cutting angle: 30° Weight: 0.424 kg Special features ISO designation: 2020 Product type: Clamping holder ECLASS: 21181004 FAQ What shank dimensions does this holder use? The holder is specified with a 20 x 20 mm square shank, matching the ISO 2020 format for secure seating. Is the tool holder suitable for compact setups on small lathes? Yes; the 125 mm overall length of the P091TM reduces projection and is intended for use where limited clearance and increased rigidity are priorities. What is the cutting angle and how does it affect machining? The holder employs a 30° cutting angle, which balances chip control and cutting forces to support consistent surface quality in turning operations. How heavy is the clamping holder and what does that mean for handling? At 0.424 kg, the holder is lightweight enough for routine handling while remaining substantial for stable clamping in everyday workshop use. Which standard designation applies to this tool holder? The unit carries the ISO designation 2020, facilitating compatibility with standard toolposts and simplifying stock management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; eMail: info@metav-werkzeuge.com

Benefit from secure clamping and compact accessibility: the right‑hand configuration combined with the MTJNR 2020 geometry ensures reproducible seating for TN--2204 indexable inserts, while the 125 mm overall length and 20 x 25 mm head ease installation in confined toolposts. Order the clamping holder directly via Metav Werkzeuge or consult the technical team for application advice. Clamping holder MTJN (MTJNR 2020) — Right‑hand turning holder for TN--2204 indexable inserts | Teknik Makina The Clamping holder MTJN (MTJNR 2020) is a right‑hand turning toolholder engineered to accept TN--2204 indexable inserts, optimised for compact toolpost layouts and repeatable clamping in production and workshop environments. Right‑hand cutting direction Compatible with TN--2204 inserts ISO MTJNR 2020 designation Compact head: 20 x 25 mm Consistent cutting performance with defined geometry The holder's clamping geometry and the 93° cutting angle support a predictable chip flow and stable cutting forces, which is particularly important in series production and precision turning. Built for use with indexable inserts, the design reduces setup variability and accelerates insert changes. The robust seating of the insert pocket delivers high repeatability, minimising downtime caused by re‑adjustment and preserving toolpath accuracy across batches. Space‑saving form with effective rigidity A short overall length of 125 mm combined with a compact head of 20 x 25 mm provides access to tight toolpost arrangements without compromising stiffness. The cutting height 40 mm ensures correct centreline alignment in many toolholders, while the modest mass of 0.429 kg keeps inertia low for quick tool changes. Together, these dimensions allow the holder to be used where a conventional longer tool would either interfere with fixtures or induce chatter, offering a practical balance of reach and rigidity. Clear compatibility and straightforward integration Designed for TN--2204 indexable inserts and identified as MTJNR 2020 in ISO terminology, the holder ties directly into standard tooling systems and insert families. The right‑hand feed direction makes it suitable for external turning operations where orientation is critical. The secondary designation K22 refers to the compatible shank interface for mounting; this facilitates integration into existing bores and clamping systems on lathes or toolposts. For workshop planners and CNC technicians, the combination of standard ISO coding and compact form factor simplifies inventory and tool planning. Contact Metav Werkzeuge for procurement of Teknik Makina turning holders and for tailored advice on integrating MTJNR 2020 geometry into current tool setups Technical data Article number: D200TM Manufacturer: Teknik Makina Designation: MTJNR 2020 For: MTJN for TN-- indexable inserts Compatible inserts: TN-- 2204 Cutting direction: right Core data Overall length: 125 mm Holder height: 20 mm Holder width: 20 mm Cutting head width: 25 mm Cutting height: 40 mm Weight: 0.429 kg Cutting angle: 93° Special features Right‑hand turning holder ISO designation MTJNR 2020 Bohrstangen designation: K22 Suitable for TN--2204 indexable inserts FAQ Which inserts fit this holder? The holder is designed for TN--2204 indexable inserts; the MTJNR 2020 pocket aligns with the insert geometry to ensure repeatable seating and reliable cutting performance. Is this toolholder for right‑hand turning only? Yes, the tool is configured for right‑hand cutting direction and is intended for external turning operations where a right‑hand feed is required. What dimensions are important for set‑up? Key dimensions are overall length 125 mm, head size 20 x 25 mm, cutting height 40 mm and weight 0.429 kg; these determine clearances, centreline alignment and dynamic behaviour in the toolpost. What does MTJNR 2020 mean? MTJNR 2020 is the ISO style designation for this holder family, indicating the pocket and shank geometry compatible with the TN-- insert series and standard turning tool conventions. Can this holder be used in compact CNC toolposts? Yes, the compact head and moderate length are intended to provide access in confined toolpost spaces while maintaining secure clamping for production‑grade turning. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of compact rigidity and secure insert clamping for consistent turning performance; the right-hand design and 125 mm overall length enable deeper reach without sacrificing stability. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Clamping holder for SCMT 09T3 indexable inserts — 125 mm, right-hand (Teknik Makina) The clamping holder for SCMT 09T3 indexable inserts is a right-hand turning toolholder designed for industrial and workshop lathes, offering rigid support and secure insert fixation for routine and precision turning tasks. Compatible with SCMT 09T3 indexable inserts 125 mm overall length for deep reach 45° cutting angle for precision turning Robust 20 x 20 mm shank dimensions Improved turning accuracy through compact rigidity The holder’s compact 20 x 20 mm shank and 125 mm overall length provide a balance between reach and stiffness, which reduces vibration and improves surface finish. A 45° approach angle concentrates cutting forces for predictable chip formation and easier toolpath control; this is particularly relevant in serial production where cycle-time variation must be minimised. By concentrating on geometry and clamping stability, the design supports consistent part tolerances and extended insert life, reducing unplanned tool changes and downtime. Fast and reliable insert clamping for efficient set-up Compatibility with SCMT 09T3 indexable inserts simplifies inventory and changeovers, while the securing screw specification M4x10 together with the T15 drive ensures firm retention under cutting loads. The combination of straightforward fastening and a well-defined pocket geometry means insert seating and repeatability are ensured; set-up time is therefore reduced and machine utilisation increased. The toolholder’s moderate mass (0.373 kg) keeps handling simple while still providing sufficient mass to dampen chatter during turning cycles. Designed for workshop and industrial use with clear specifications The toolholder features a 25 mm cutting head width and a 25 mm cutting height, dimensions that offer compatibility with typical insert profiles and give the clearance required for a range of turning operations. The ISO designation 2020 indicates the shank format for toolpost mounting, easing integration into standard toolposts. Manufactured by Teknik Makina and supplied under SKU D465TM, the component is intended as a practical, long-lived addition to turning tool inventories, supporting repeatable performance across batches without complex adjustments. For secure right-hand turning with SCMT 09T3 inserts, request ordering information or technical advice from Metav Werkzeuge GmbH in Emmerich — contact via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific machining tasks. Technical Data Article number: D465TM Label: Klemmhalter SCMT 09T3 L125mm ECLASS: 21181004 Brand: Teknik Makina Facts Overall length: 125 mm Shank width: 20 mm Shank height: 20 mm Cutting head width: 25 mm Cutting height: 25 mm Cutting angle: 45° Weight: 0.373 kg Screw: M4x10 Torx key: T15 ISO designation: 2020 Special features Compatible with SCMT 09T3 indexable inserts Right-hand cutting direction Compact 20 x 20 mm shank format Designed for industrial and workshop turning applications FAQ Which inserts fit this clamping holder? The clamping holder is compatible with SCMT 09T3 indexable inserts; the pocket geometry is matched to this insert family for secure seating. Is the toolholder suitable for right-hand turning only? Yes, this holder is specified for right-hand cutting direction and is intended for right-hand turning operations. What fastening hardware is used to secure the insert? Insert retention uses an M4x10 screw tightened with a T15 Torx drive to ensure reliable clamping under machining loads. What are the shank dimensions and mounting format? Shank dimensions are 20 x 20 mm with an ISO designation of 2020, allowing straightforward mounting in compatible toolposts. What is the product code for ordering and specification reference? The product is supplied as SKU D465TM by Teknik Makina, labelled "Klemmhalter SCMT 09T3 L125mm" for reference. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a secure clamping solution that combines compatibility with SCMT 09T3 indexable inserts, a compact 20 x 20 mm shank for high rigidity and a 125 mm overall length for extended reach; order the tool directly via Metav Werkzeuge or contact the consultants for application advice. Clamping holder SCMT 09T3 L125mm — left-hand, 45° cutting geometry by Teknik Makina Clamping holder SCMT 09T3 L125mm is a left-hand toolholder engineered for turning operations with SCMT 09T3 indexable inserts, offering a robust clamping system and a 45° rake to support finishing tasks in confined toolposts. Secure clamp for SCMT 09T3 inserts 125 mm overall length for deep reach Left-hand cutter with 45° cutting angle Reliable clamping and compatibility for stable production The Clamping holder SCMT 09T3 L125mm is designed for secure retention of SCMT 09T3 indexable inserts and uses an M4x10 fastening screw driven with a T15 Torx key to reduce the risk of cam‑out. The clamping arrangement provides repeatable seating of the insert, which is essential for consistent cycle times and predictable tool life. Compatibility with the SCMT 09T3 insert family simplifies inventory and replacement, while the specified fastening components allow controlled assembly and straightforward maintenance of clamping integrity. Geometry that lowers cutting forces and improves finishes A 45° cutting angle combined with a 25 mm cutting head width and 25 mm cutting height results in a geometry that reduces radial cutting forces and supports improved surface quality during finishing passes. The 20 x 20 mm shank dimensions increase torsional stiffness in the toolpost, so vibrations are minimised and insert edge wear is reduced. This geometry supports predictable cutting behaviour, which is particularly valuable when machining demanding materials or when repeatability across batches is required. Compact reach and workshop integration for versatile use With an overall length of 125 mm, the holder provides added reach for parts with restricted access while remaining compact enough for standard toolposts. The ISO 2020 designation and the listed dimensional data enable straightforward integration into existing setups and tool management systems, simplifying tool changeover and documentation. The modest mass and balanced proportions make the component suitable for both single‑piece flows and small-batch production where tool stability and changeover speed matter. Service‑friendly fastening and robust design for daily use The combination of a Torx‑driven screw and a defined screw size (Torx T15, M4x10) supports reliable torque application and reduces wear on the drive interface during repeated servicing. The left‑hand orientation is tailored to specific turning directions and optimises chip flow for associated toolpaths. The holder’s construction prioritises repeatability and long service intervals, contributing to uninterrupted production and lower refurbishment effort over time. Reference SKU D469TM for ordering and inventory tracking. Contact Metav Werkzeuge to secure supply and technical advice for Teknik Makina clamping holders — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application details and availability Technical data SKU: D469TM Label: Clamping holder SCMT 09T3 L125mm Product type: Clamping holder Manufacturer: Teknik Makina eClass: 21181004 Core dimensions & weights Overall length: 125 mm Weight: 0.373 kg Shank width: 20 mm Shank height: 20 mm Cutting head width: 25 mm Cutting height: 25 mm Cutting angle: 45° Screw: M4x10 Compatibility & special features Compatible with SCMT 09T3 indexable inserts Left-hand cutting direction ISO designation: 2020 Torx key: T15 FAQ Is this holder compatible with SCMT 09T3 inserts? Yes. The clamping system is designed specifically for SCMT 09T3 indexable inserts and ensures correct seat and repeatability. Which cutting direction does the tool support? The tool is configured for left‑hand turning operations; the left orientation is built into the holder geometry. What are the shank dimensions and overall length? Shank: 20 x 20 mm; overall length: 125 mm, suitable for common toolposts and extended reach tasks. Which screw and driver are required for clamping? Clamping uses an M4x10 screw operated with a Torx T15 key for secure torque application and reduced drive wear. What is the product SKU for ordering and stock reference? The SKU is D469TM for the Teknik Makina clamping holder SCMT 09T3 L125mm. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precise clamping solution that combines secure insert retention, standard shank compatibility and reduced setup time; the compact design and robust fastening lower downtime and improve process repeatability — order directly via Metav Werkzeuge or contact our consultants for tailored advice. Klemmhalter VER16 L125mm — clamping holder for VER16 indexable inserts with 125 mm overall length Klemmhalter VER16 L125mm serves as a compact clamping solution for turning and toolpost applications, designed to accept VER16 indexable inserts and to integrate with standard 20 × 20 mm shank tool systems. Clamping holder for VER16 indexable inserts 125 mm overall length for extended reach 20 × 20 mm shank for standard toolholders Torx T15 fastening with M3.5×8.5 screw Secure clamping for consistent machining results A precise clamping solution reduces vibration and improves repeatability on the shop floor. The Klemmhalter VER16 L125mm features a solid interface for VER16 inserts and a robust fastening arrangement using an M3.5×8.5 screw tightened with a T15 Torx key. This configuration provides dependable insert retention during interrupted cuts and when machining at moderate feeds, contributing to tighter tolerances and fewer rejects. The compact head geometry with a 22 mm cutting head width supports stable chip evacuation and consistent tool positioning, translating technical precision into measurable production quality. Faster changeover and predictable workshop throughput Minimising non-productive time is central to efficient workflows. The straightforward fastener arrangement and standardised shank format allow for quick insert replacement and rapid tool swaps in toolposts and quick-change systems. The clamping interface and the ISO 2020 shank dimensions simplify integration into existing toolholder inventories, reducing search time and setup complexity. By standardising on proven formats and clear mechanical interfaces, the holder supports consistent cycle times and predictable output, which is particularly valuable in small-batch production and mixed-program turning operations. Built for compatibility with common tool systems The holder’s 20 × 20 mm shank and 125 mm overall length combine to offer reach without compromising rigidity. These dimensions make the component suitable for typical lathes and CNC turning centres where toolpost clearance and overhang are factors. The 30 mm cutting height specification ensures the insert sits at an appropriate centre height for many set-ups when paired with standard toolposts, lowering the need for shims or additional adaptation. The compact mass of 0.36 kg contributes to dynamic stability and reduces inertial effects during acceleration phases. Clear specification and workshop-friendly maintenance Technical clarity supports reliable procurement and operation. The holder is identified under SKU D525TM and is manufactured by Teknik Cutting Tools, ensuring traceability and consistent production standards. Maintenance is straightforward: the Torx fastening offers repeatable torque application for uniform clamping force and easy access for inspection. Where interchangeability with VER16 inserts is required, no additional adapters are needed, making the holder a practical choice for workshops aiming to simplify their tooling landscape while maintaining machining performance. Contact Metav Werkzeuge for personalised technical advice and to discuss how the Teknik Cutting Tools Klemmhalter VER16 L125mm can be integrated into existing turning operations — Metav Werkzeuge provides direct supply from Emmerich and consultancy to match the toolholder to the application Technical data Article number: D525TM Product type: Clamping holder Brand: Teknik Makina Designation: Klemmhalter VER16 L125mm For inserts: VER16 ISO designation: 2020 Core specifications Overall length: 125 mm Shank width: 20 mm Shank height: 20 mm Cutting head width: 22 mm Cutting height: 30 mm Weight: 0.36 kg Screw: M3.5×8.5 Torx key: T15 Compatibility & features For VER16 indexable inserts Compatible with ISO 2020 shank systems SKU: D525TM Product category: Klemmhalter FAQ Which inserts fit this clamping holder? The holder accepts VER16 indexable inserts; compatibility is defined by the insert designation and the clamping geometry of this Klemmhalter. What are the shank dimensions and why do they matter? Shank dimensions are 20 × 20 mm, which align with many standard toolpost and quick-change systems, ensuring mechanical fit and rigidity. How is the insert secured in the holder? The insert is fastened with an M3.5×8.5 screw tightened using a T15 Torx key to provide consistent clamping force and repeatable torque settings. Is the holder suitable for heavy interrupted cuts? The holder’s rigid shank and solid clamping interface are intended to improve stability in interrupted cutting, though final suitability depends on machine power and cutting parameters. What is the product identifier for ordering or referencing? Reference SKU D525TM and the designation Klemmhalter VER16 L125mm when enquiring or ordering to ensure the correct item. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Secure right‑hand turning with a compatible VCMT 1604 insert and a 125 mm reach offers stable, repeatable machining for many lathe operations. Order the SVJC clamping holder directly via Metav Werkzeuge or consult their specialists for application advice. SVJC clamping holder for VCMT indexable inserts (SVJCR 2020) — right‑hand, 125 mm by Teknik Makina A SVJC clamping holder designed for reliable right‑hand turning with VCMT 1604 indexable inserts, providing extended reach and repeatable clamping for workshop and industrial turning tasks. Right‑hand turning configuration Compatible with VCMT 1604 inserts 125 mm overall length for extended reach ISO SVJCR 2020 standard High rigidity for consistent turning results The holder is engineered to deliver rigid clamping and consistent tool positioning during standard right‑hand turning. With a cutting height of 33 mm and a cutting angle of 93°, the assembly supports neutral approach geometry that suits a wide range of general‑purpose turning operations. The resulting stability promotes predictable chip formation and repeatable diameters, which is particularly valuable in serial production where process consistency drives efficiency and reduces rework. Precise compatibility reduces setup time Designed specifically for VCMT 1604 indexable inserts, the toolholder follows the ISO SVJCR 2020 designation to ensure a standardised fit and predictable seat alignment. The shank designation K16 simplifies selection for compatible tool posts and clamping systems. Translating standards into practice, this compatibility means less trial‑and‑error at the machine, shortened tool change intervals and a faster return to productive cutting — attributes that improve throughput in both small workshops and larger CNC cells. Practical dimensions for workshop integration With an overall length of 125 mm, holder height of 20 mm and head width of 25 mm, the design balances reach and stiffness for common turning tasks. The compact footprint and moderate weight (0.385 kg) make the component straightforward to handle during tool set‑up while the geometry supports access to shoulder and profile areas. For workshop planners, these dimensional data enable rapid verification of clearance and collision risk before mounting, reducing downtime during tool changes and set‑ups. Choose Teknik Makina’s SVJC clamping holder for dependable right‑hand turning and contact Metav Werkzeuge in Emmerich for ordering and technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D246TM Manufacturer: Teknik Makina Designation (EN): SVJC for VCMT Indexable Inserts ISO designation: SVJCR 2020 Suitable for inserts: VCMT 1604 Cutting direction: right Facts Overall length: 125 mm Weight: 0.385 kg Cutting height: 33 mm Holder height: 20 mm Holder width: 20 mm Cutting head width: 25 mm Cutting angle: 93° Special features For VCMT 1604 indexable inserts ISO SVJCR 2020 conformity Right‑hand turning configuration Shank designation: K16 FAQ Which insert grade and size fit this holder? The holder is specified for VCMT 1604 indexable inserts; appropriate grades and coatings should be selected according to the machined material and cutting conditions. Is this a right‑hand or left‑hand toolholder? This model is configured for right‑hand turning operations, as indicated by the right cutting direction designation and the SVJCR geometry. What is the overall length and how does that affect reach? The 125 mm overall length provides extended reach for deeper shoulders and external profiles while maintaining sufficient rigidity for standard turning tasks. What is the ISO designation and why is it important? The ISO SVJCR 2020 designation identifies the toolholder geometry and seat standard, ensuring compatibility with matching inserts and predictable clamping alignment. What shank size is specified for machine mounting? The shank is listed as K16, which helps when checking compatibility with the machine’s tool post or turret insert plates. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a robust 125 mm diameter, a true 90° cutting angle and integrated internal coolant delivers stable, repeatable performance for demanding machining tasks; benefit from precise insert seating and reduced thermal wear. Order the tool directly via Metav Werkzeuge or consult the technical specialists for suitability and delivery. Corner Indexable Head T190-1TM — 125 mm, internal coolant (Teknik Makina) A compact Corner Indexable Head engineered for AP-- 1604 indexable inserts, optimised for right‑angle machining where coolant-fed cutting and compact assembly are required 125 mm diameter for wide engagement Internal coolant for improved tool life Compatible with AP-- 1604 Korloy inserts 90° cutting angle for precise shoulder work Stable cutting performance for continuous machining The Corner Indexable Head is built to translate tool geometry into consistent results: the 125 mm tool body with a 90° cutting angle positions inserts for square shoulder cuts and firm contact, while the arrangement of 9 cutting edges distributes cutting forces to reduce vibration. This configuration supports longer uninterrupted cycles, improving productivity and delivering reliable dimensional outcomes. The presence of internal coolant further stabilises temperatures at the cutting zone, helping to maintain surface quality and insert life. Serviceable, maintenance-friendly design reduces downtime A maintenance-conscious layout simplifies routine interventions. Fastening uses M4x10 Torx screws secured with a T15 key, enabling quick insert changes and repeatable clamping without special tooling. Compatibility with Korloy AP-- 1604 indexable inserts streamlines inventory and procurement, allowing stock consolidation for carbide grades and geometries already in use. Clear mechanical interfaces and standard screw sizes reduce downtime during tool swaps and setup adjustments. Compact integration for precise setups in confined spaces At an overall length of 62 mm and with a 40 mm shank diameter, this head offers a compact footprint suited to tight fixturing and limited overhangs; the relatively low mass of 3.642 kg aids handling during tool changes and contributes to predictable dynamic behaviour on the spindle. The unit is supplied as SKU T190-1TM by Teknik Makina, making identification straightforward for ordering and tool management. The compact geometry supports accessible toolpaths and repeatable alignment within clustered tool arrangements. Discuss the T190-1TM with Metav Werkzeuge to confirm fitment, lead times and compatible insert grades — contact via info@metav-werkzeuge.com or call +49 2822 7131930 for expert advice and procurement from our Emmerich warehouse Technical Data Article number: T190-1TM Product type: Corner indexable head Manufacturer: Teknik Makina Compatible inserts: AP-- 1604 Compatible insert maker: Korloy Facts Diameter: 125 mm Overall length: 62 mm Shank diameter: 40 mm Weight: 3.642 kg Cutting angle: 90° Cutting edges: 9 ECLASS: 21181015 Special features Internal coolant: yes Torx screw: M4x10 Torx key: T15 Label: 125mm Eckmesserkopf AP-- 1604 L62mm mit Innenkühlung Description (EN): for AP-- 1604 Indexable Inserts FAQ Which indexable inserts fit this head? The head accepts AP-- 1604 indexable inserts; Korloy AP-- 1604 inserts are listed as compatible with the T190-1TM. Does the head provide internal coolant to the cutting zone? Yes — the T190-1TM features internal coolant channels to support cooling at the tool-tooth interface and help extend insert life. What fastening hardware is required for insert clamping? Insert clamping uses M4x10 screws tightened with a Torx T15 key as specified for the T190-1TM. Is this head suitable for square shoulder operations? Yes — with a 90° cutting angle and the insert geometry for AP-- 1604, the head is configured for precise shoulder and right‑angle machining. How can the SKU be used for ordering or stock management? Reference SKU T190-1TM when ordering or checking stock to ensure the correct Corner Indexable Head and configuration are supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a rigid, high‑stability design with a 90° cutting angle and Ø125 mm diameter for consistent square‑shoulder machining; order the corner tool head via Metav Werkzeuge or consult their specialists for process integration. Corner tool head T519TM — for XOMX 1204 indexable inserts, Ø125, 90° (Teknik Cutting Tools) A robust corner tool head T519TM engineered for precision square‑shoulder and face operations using XOMX 1204 indexable inserts; suitable for medium‑ to heavy‑duty turning and milling tasks in production workshops Heavy‑duty 125 mm diameter head 90° cutting angle for square shoulder cuts Compatible with XOMX 1204 indexable inserts Secured with M3.5x8.5 Torx screw, T10 key Stability and repeatability for productive machining Built with a large Ø125 mm head and a defined 90° cutting geometry, this clamping solution delivers consistent contact and reduced deflection on interrupted cuts. The substantial mass and geometric arrangement translate into improved surface quality and dimensional stability across series production. For workshops seeking to reduce rework and scrap rates, the rigid design supports predictable tool life and machining outcomes. Quick clamping and reliable insert retention Clamping is performed with a M3.5x8.5 Torx screw operated by a T10 key, providing secure, repeatable retention of the insert during high‑load operations. Compatibility with XOMX 1204 inserts and established manufacturers such as SECO ensures a wide choice of grades and geometries, simplifying tool‑set standardisation and spare‑parts logistics. The straightforward screw‑based fastening shortens changeover times and reduces downtime on the shop floor. Installation and mechanical integration simplified Designed for a 40 mm mounting bore (40 mm) and an overall length of 62 mm, the head fits commonly used toolholders and post configurations without extensive adapter work. With a mass of 3.565 kg, balance considerations are advised for high‑speed spindles, but the weight contributes to damping and steady cutting behaviour where stability is prioritised. Planning with these fixed dimensions eases fixture design and cycle‑time calculations. Application scope and operational benefits Equipped with 12 cutting edges and a square configuration suitable for face and shoulder cuts, this head is tailored for shops that prioritise reliable part geometry over extreme light‑cutting strategies. The combination of a defined cutting angle, standard insert format and proven fastening method supports both single‑piece flow and batch production. The result is fewer tool interventions and a more predictable production rhythm. For application guidance and availability of the Teknik Cutting Tools corner tool head T519TM, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: T519TM Manufacturer: Teknik Makina Designation: Corner tool head for XOMX 1204 indexable inserts Core measurements Diameter: 125 mm Mounting bore: 40 mm Overall length: 62 mm Cutting angle: 90° Cutting edges: 12 Weight: 3.565 kg Materials & features Compatible inserts: XOMX 1204 Compatible insert manufacturer: SECO Fastening: Torx screw M3.5x8.5 Torx key size: T10 Story trigger: eckmesserkopf FAQ Which insert type fits this head? The corner tool head accepts XOMX 1204 indexable inserts; insert grades and geometries from manufacturers such as SECO can be used depending on the application. What are the main mounting dimensions to check? Check the 40 mm mounting bore and the 62 mm overall length to ensure compatibility with existing toolholders and posts. How is the insert secured in the head? Retention is via a M3.5x8.5 Torx screw tightened with a T10 key, providing repeatable clamping for production use. Is this head suitable for heavy interrupted cuts? The large Ø125 mm head and robust construction make it well suited to operations where stability and deflection control are priorities. Does the head require balancing for high‑speed use? At 3.565 kg, dynamic balance should be verified for high‑speed spindles; the mass improves damping but shop‑specific balancing is recommended. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, proven Sandvik R390 18 compatibility and a rigid 125 mm diameter design for stable turning operations; order directly via Metav Werkzeuge or contact our consultants for application advice. Corner turning head — for R390 18 indexable inserts, 125 mm diameter, internal coolant (Teknik Makina) Corner turning head designed for precision turning tasks in production and workshop environments, compatible with R390 18 indexable inserts and optimised for coolant-through operation 125 mm diameter for extended reach Internal coolant feed for reliable chip control Compatible with Sandvik R390 18 inserts Robust design, 8 effective cutting edges Enhance machining stability and throughput with a rigid 125 mm solution The corner turning head delivers consistent performance for shoulder and groove turning where rigidity matters. The 125 mm diameter increases the tool overhang capacity while maintaining stiffness, reducing chatter and allowing higher material removal rates. A 90° cutting angle provides straightforward geometry for right-angle operations, and the use of R390 18 indexable inserts simplifies tool maintenance: inserts are indexed or replaced without complex reclamping, cutting downtime and component handling. These characteristics translate into measurable productivity gains at the machine spindle and a predictable cycle time for batch production. Simplified setup and coolant-assisted tool life Integration into existing tool posts is fast thanks to the standard 40 mm shank and compact profile. The 40 mm shank and 62 mm overall length balance access and stability, keeping set-up adjustments to a minimum. Internal coolant feed is delivered directly to the cutting zone: internal coolant improves chip evacuation, reduces built-up edge and extends insert life, particularly on difficult-to-machine alloys. Fixing is straightforward with T15 Torx drive and M4x10 screws, ensuring repeatable clamp forces and secure insert retention. Compatibility with Sandvik insert geometry means familiar grades and edge forms can be used straight away, avoiding trial-and-error testing. Designed for reliability and predictable production A compact yet substantial mass contributes to vibration damping and positional stability during heavy cuts; the tool head’s balance and 3.558 kg mass support smoother cuts under load. With 8 cutting edges available from the installed inserts, maintenance intervals are extended and tool costs per part are reduced. The overall result is precision and repeatability across runs, making the holder suitable for serial turning applications and mixed-production shops that require consistent surface finish and dimensional control. The robust construction also supports quick index changes and straightforward tool reconditioning. Contact Metav Werkzeuge in Emmerich for a compatibility check or technical quote for this Teknik Makina corner turning head (SKU T430-1TM); email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: T430-1TM Manufacturer: Teknik Makina Product type: Corner turning head Description: for R390 18 indexable inserts (Sandvik compatibility) Core dimensions Diameter: 125 mm Shank diameter: 40 mm Overall length: 62 mm Weight: 3.558 kg Cutting angle: 90° Features & fittings Internal coolant Compatible with Sandvik R390 18 inserts Cutting edges: 8 Torx key: T15 Torx screw: M4x10 FAQ Which insert series fits this tool? The tool accepts R390 18 indexable inserts and is finished for Sandvik-compatible insert geometry, making the insert selection straightforward for established turning grades. Is the coolant routed to the cutting edge? Yes — internal coolant supplies coolant directly to the cutting zone, improving chip removal and insert life for the Teknik Makina corner turning head (SKU T430-1TM). What shank and overall dimensions does it require? The holder uses a 40 mm shank with a 62 mm overall length, designed for standard tool post interfaces and compact installation in turning centres. How many effective cutting edges are available per setup? The assembly supports the indexed insert layout delivering 8 cutting edges, extending service intervals and reducing per-part tool cost. Which fixation hardware is required for insert replacement? Insert clamping uses T15 Torx drive with M4x10 screws for secure and repeatable fastening in everyday workshop practice. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of rigidity, coolant-fed chip control and secure clamping to maintain steady turning cycles; the 125 mm diameter and internal coolant ensure longer insert life and consistent surface quality. Order supply and technical advice are available via Metav Werkzeuge for seamless integration into existing tool holders. Corner tool head T592-3TM — 125 mm angle head with internal coolant (for ADKT 1706 Indexable Inserts) The Corner tool head T592-3TM is a precision-fit angle head designed for turning operations with ADKT 1706 indexable inserts, engineered to deliver stable cutting and reliable coolant delivery in demanding production environments. 125 mm diameter for high rigidity Internal coolant for improved insert life Compatible with ADKT 1706 indexable inserts Secure Torx clamping with M4x10 screws Stable cutting geometry for consistent finishing The tool head offers a 125 mm diameter body and a precisely set 90° cutting angle, delivering enhanced rigidity during interrupted and continuous cuts. This geometry, combined with 8 cutting edges, reduces vibration and promotes repeatable surface finish quality across batch production. The design supports high reproducibility in component dimensions, which is essential when tolerances are tight and process stability is required. The result is fewer reworks and a steadier machine utilisation rate. Internal coolant for extended insert life and reliable chip control Equipped with internal coolant, the unit channels cutting fluid directly to the cutting zone, supporting efficient heat dissipation and improved chip evacuation. When used with ADKT 1706 inserts from Korloy, the focused coolant flow helps to moderate cutting temperatures and reduces built-up edge formation, extending tool life and maintaining consistent cycle times. For workshops aiming to lower tooling consumption and increase uptime, the coolant-fed configuration translates directly into lower overall operating costs. Quick serviceability and secure fastening to reduce downtime Maintenance and insert changes are simplified by standardised fastening: Torx T15 driver engagement with M4x10 screws ensures fast, reliable clamping and easy repeatability after reassembly. The compact L63 mm overall length keeps the cutting centre close to the holder, improving stiffness, while a manageable mass of 2.89 kg provides a balance between robustness and installation convenience. These characteristics support efficient tool changeovers and predictable machining behaviour in mixed-production environments where throughput and flexibility matter. Discuss compatibility and supply with Metav Werkzeuge — request a tailored quote or technical check for Teknik Makina's corner tool head T592-3TM, supplied directly from our Emmerich hub. Technical data SKU: T592-3TM Label: 125mm Eckmesserkopf ADKT 1706 L63mm mit Innenkühlung Product type: Corner tool head Facts Diameter: 125 mm Overall length: 63 mm Weight: 2.89 kg Cutting edges: 8 Cutting angle: 90° Torx key: T15 Torx screw: M4x10 Special features Internal coolant: yes Suitable for indexable inserts: ADKT 1706 Compatible insert manufacturer: Korloy Manufacturer: Teknik Makina SKU/UID: T592-3TM / T592-3TM FAQ What inserts fit this corner tool head? The corner tool head T592-3TM is designed for ADKT 1706 indexable inserts; compatibility with Korloy-manufactured ADKT 1706 inserts is specified for optimal fit. Does the tool head provide internal coolant delivery? Yes, the T592-3TM features internal coolant to the cutting zone, aiding heat control and chip evacuation during turning operations. Which fastening system is used for insert clamping? Clamping is via M4x10 Torx screws with a T15 driver profile to ensure secure and repeatable fastening. Is the cutting angle suitable for general turning tasks? The tool head presents a 90° cutting angle, offering a versatile geometry suitable for a wide range of turning and finishing applications. What are the key dimensional data for machine setup? Relevant setup values: 125 mm diameter and 63 mm overall length; use these figures to verify clearance and holder compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 125 mm cutting diameter, a 90° cutting angle and compatibility with ANHX 1206 indexable inserts to achieve stable shoulder milling and consistent chip evacuation; procure the cutter head directly via Metav Werkzeuge or consult their specialists for supply and configuration advice. Corner milling head T646TM by Teknik Makina — 125 mm, for ANHX 1206 indexable inserts The Corner milling head T646TM is a 90° tool head engineered for secure shoulder and face milling operations using ANHX 1206 indexable inserts. 125 mm diameter for stable cutting Compatible with ANHX 1206 inserts 40 mm shank for secure clamping 14 cutting edges for high productivity High productivity through engineered geometry and robust stability The cutter delivers predictable cycle times thanks to its large 125 mm diameter and a true 90° cutting angle, which together produce consistent shoulder faces and minimise rework. The combination of multiple cutting edges translates into fewer tool changes: with 14 cutting edges, the machining rhythm is increased and downtime is reduced. This makes the tool particularly suited to batch production and components requiring repeatable right-angled faces, improving overall process efficiency. Fast setup and safe clamping for reliable machining Designed with a 40 mm shank, the head seats securely in standard toolholders, reducing axial play during heavy cuts. The clamping concept is supported by a Torx fixation system; the head uses an M3.5x8.5 Torx screw tightened with a T15 key, enabling quick and repeatable assembly. These details simplify changeover routines and provide a predictable torque interface, lowering the risk of assembly errors and improving shop-floor safety. Broad compatibility for flexible tooling strategies Acceptance of ANHX 1206 indexable inserts — compatible with manufacturers such as Palbit — gives the head access to a wide range of grades and chipbreakers. This flexibility allows process engineers to optimise inserts for steel, alloyed materials or finishing passes without changing the head geometry. By separating the cutting edge from the body, maintenance is concentrated on consumables rather than the holder, which supports lower lifecycle costs and streamlined inventory management. Practical benefits from purchase to production Sourcing the head through a trusted distributor enhances supply security and practical support. The component’s robust build and clear specification reduce inspection time at receipt and permit rapid integration into existing tool assemblies. Combined with Metav Werkzeuge’s emphasis on reliable supply from Emmerich and their broad product range, this head is a pragmatic choice for workshops seeking measurable improvements in throughput and consistency. For precise shoulder milling choose the Teknik Makina corner milling head T646TM via Metav Werkzeuge — contact the Metav specialists at info@metav-werkzeuge.com or on +49 2822 7131930 for tailored advice and reliable supply from Emmerich. Technical data Article number (SKU): T646TM Brand: Teknik Makina Designation: Corner milling head for ANHX 1206 indexable inserts Facts Diameter: 125 mm Cutting edges: 14 Overall length: 63 mm Shank diameter: 40 mm Weight: 3.091 kg Cutting angle: 90° Special features Compatible inserts: ANHX 1206 Suitable insert manufacturer: Palbit Torx screw: M3.5x8.5 Torx key size: T15 FAQ What inserts fit this milling head? The head accepts ANHX 1206 indexable inserts; compatible grades from manufacturers such as Palbit can be used depending on the material and finish requirement. What is the shank size and how does it affect clamping? The tool features a 40 mm shank diameter designed for standard toolholders, delivering secure clamping and reduced axial movement during heavy cuts. How many cutting edges does the head provide and what is the benefit? With 14 cutting edges, the head increases productive cutting length per assembly, reducing the frequency of changeovers and improving uptime. Which screw and key are required for insert replacement or maintenance? Insert and component fastening is effected with an M3.5x8.5 Torx screw using a T15 key for consistent torque and quick serviceability. Is this tool suitable for shoulder milling on high-volume parts? Yes; the combination of a 125 mm diameter and a 90° cutting angle makes the head well suited to repetitive shoulder milling where dimensional stability and surface consistency are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust 125 mm corner milling head with internal coolant and compatibility for LNGX 1307 indexable inserts ensures controlled chip evacuation and extended tool life. With eight cutting edges and a compact 63 mm overall length, the solution reduces tool changes and improves cycle consistency. Order the corner milling head directly via Metav Werkzeuge or ask the consultants for tailored specification support. Corner milling head for LNGX 1307 indexable inserts — 125 mm, internal coolant (Teknik Makina) A corner milling head engineered for stable face and corner machining in high-production CNC environments, compatible with LNGX 1307 indexable inserts and equipped with internal coolant. *125 mm diameter for stable cutting *Internal coolant for reliable chip control *LNGX 1307 compatible with Walter inserts *Eight cutting edges for efficient productivity Consistent performance through optimised coolant and geometry The compact tool head delivers repeatable results thanks to its internal coolant channel that directs cutting fluid precisely to the cutting zone. This targeted supply reduces heat build-up and improves surface quality on each pass, which translates into longer insert life and fewer interruptions on the shop floor. The design keeps vibration low and supports steady cutting forces, providing a measurable gain in machining stability for serial production runs. Reduced downtime with multiple effective cutting edges Equipped with 8 cutting edges, the head allows longer intervals between indexings compared with single-edge solutions, lowering changeover frequency and increasing spindle uptime. The 90° cutting angle yields predictable engagement and simple toolpath strategies for corner and face operations. This combination of geometry and edge count supports efficient material removal while maintaining dimensional control, especially when paired with standard LNGX 1307 inserts. Compact design and clear compatibility for seamless integration With a diameter of 125 mm and an overall length of 63 mm, the toolhead occupies minimal space in tool magazines while offering sufficient overhang for many fixture layouts. Compatibility with inserts from Walter and the LNGX 1307 series simplifies procurement and reduces the need for bespoke tooling. Fastener details such as T15 Torx drive and M4x11 screws ensure secure clamping and straightforward maintenance when replacing inserts or servicing the head. Contact Metav Werkzeuge for a machining consultation or to request detailed drawings and compatibility advice for the Teknik Makina corner milling head T495-1TM. Technical data SKU: T495-1TM Eclass: 21181015 Product type: Corner milling head Manufacturer: Teknik Makina Core dimensions Diameter: 125 mm Overall length: 63 mm Weight: 3.555 kg Number of cutting edges: 8 Cutting angle: 90° Features / Compatibility Internal coolant For LNGX 1307 indexable inserts Compatible with inserts by Walter Torx key: T15 Torx screw: M4x11 FAQ What materials is this head suitable for? The corner milling head is designed for general-purpose face and corner operations; compatibility with specific materials depends on the selected LNGX 1307 inserts and machining parameters, so matching insert grade to the workpiece is recommended. How does internal coolant improve machining with this head? Internal coolant in the T495-1TM directs fluid to the cutting edge, reducing temperature at the tool–workpiece interface and improving insert life and surface finish compared with external-only coolant. Which inserts fit this tool? This head accepts LNGX 1307 indexable inserts and is compatible with inserts supplied by Walter, providing a straightforward supply chain for replacement cutting edges. What fastening system is used for the inserts? Inserts are secured using M4x11 screws tightened with a T15 Torx driver, ensuring stable clamping under heavy cutting loads. Is the head suitable for automated tool magazines? The compact overall length (63 mm) and standard diameter make the head suitable for many automated toolchanger systems, provided the machine’s tool length and mass limits are observed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the robust 125 mm diameter, internal coolant and seven cutting edges for reliable shoulder turning and reduced cycle times; order the T370TM directly via Metav Werkzeuge or consult the technical team for application advice. Indexable Turning Head T370TM for XEKT 1904 – 125 mm, Internal Coolant (Teknik Makina) Indexable Turning Head T370TM designed for precise 90° shoulder turning with XEKT 1904 indexable inserts, suited to production lathe applications requiring stable, repeatable performance 125 mm diameter for stable cutting Internal coolant supply Seven cutting edges for extended tool life Compatible with Korloy XEKT 1904 inserts Stable cutting and consistent surface quality The large 125 mm tool body provides increased rigidity and reduced deflection during shoulder and face turning, resulting in improved dimensional stability and repeatability. The 90° cutting angle is optimised for clearances and efficient material removal while the compact L63 mm overall length keeps the cutting forces close to the spindle, which helps to reduce vibration and improves surface finish. These mechanical advantages translate into fewer reworks and a steadier production flow. Targeted cooling improves tool life and chip control Integrated internal coolant channels deliver cooling fluid directly to the cutting zone, which reduces thermal load and aids chip evacuation. For indexable insert systems such as XEKT 1904 by Korloy, this targeted coolant supply prolongs insert life and maintains edge integrity under continuous cuts. From a process standpoint, improved cooling means longer uninterrupted runs and lower tooling consumption per part. Quick, secure clamping for reduced setup time Tool change and clamping use the standard Torx T15 interface with an M4x8.5 Torx screw to ensure a secure, repeatable seat for the insert carrier. The mechanical fastenings are industry-standard, making maintenance straightforward and minimising downtime during insert changes. Simple, proven fixation also reduces the risk of seating errors and contributes to consistent cutting performance across shifts. Designed for the workshop and industrial workflows The compact but robust construction with a weight of 2.951 kg balances stiffness and handling for routine use in turning centres. The head is intended for use with indexable inserts, offering the modularity required in versatile production environments. For workshops seeking predictable supply and technical backing, the part number T370TM identifies the turning head unambiguously for procurement and inventory control. Contact Metav Werkzeuge today to discuss how Teknik Cutting Tools' turning head T370TM fits specific lathe setups and production targets — phone +49 2822 7131930 or e-mail info@metav-werkzeuge.com for tailored advice and swift delivery from Emmerich. Technical data Article number: T370TM EClass: 21181015 Manufacturer: Teknik Makina Facts Diameter: 125 mm Overall length: 63 mm Weight: 2.951 kg Cutting edges: 7 Cutting angle: 90° Torx key: T15 Torx screw: M4x8.5 Special features Internal coolant: yes Compatible with XEKT 1904 indexable inserts Inserts manufacturer compatibility: Korloy Product type: Indexable turning head FAQ What inserts fit this turning head? The turning head accepts XEKT 1904 indexable inserts; the design is matched to the insert geometry for reliable seating and chip formation. Does the tool provide coolant directly to the cutting edge? Yes, the head features internal coolant channels that deliver fluid to the cutting zone to extend insert life and improve chip evacuation. What fastener is used for the insert seat? The insert seat is secured with a Torx T15 screw, specified as M4x8.5, ensuring repeatable clamping torque and secure seating. How does the 125 mm diameter benefit machining? A 125 mm body increases stiffness and reduces deflection, which improves dimensional accuracy and surface finish during shoulder turning. Is the T370TM suitable for production turning centres? The T370TM is built for production use, offering modular indexing, robust construction and coolant support for longer running times and predictable process behaviour. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust combination of 125 mm diameter stability and compatibility with WNMU 0806 indexable inserts for reliable turning operations; the compact 63 mm overall length and clear fastening standard make integration into existing setups straightforward. Order the tool head directly via Metav Werkzeuge or contact the consultants for tailored advice. Indexable corner tool head T547TM — 125 mm diameter, for WNMU 0806 indexable inserts (Teknik Makina) The Indexable corner tool head T547TM is a compact turning solution designed for heavy-duty stability and fast insert changes in industrial turning applications 125 mm diameter for robust stability Compatible with WNMU 0806 inserts (Kyocera) Overall length 63 mm for compact mounting Ten cutting edges for longer productivity Consistent stability that reduces vibration and scrap A larger head diameter provides a solid platform: the 125 mm body helps to dampen chatter and maintain a constant tool position during interrupted cuts, which directly improves surface finish and extends insert life. The substantial mass and engineered geometry support repeatable turning results, so the machining process becomes more predictable and cycle times more consistent. This advantage is particularly relevant in production environments where component tolerances and batch consistency are decisive. Fast insert interchange and proven compatibility for uptime Designed around the WNMU 0806 insert format, the tool head accepts standard indexable inserts from Kyocera, enabling immediate use of widely available cutting grades. Quick access to the insert pocket reduces tool change time and simplifies stocking of spare inserts. The standardised mounting and insert interface make tool setup straightforward on mixed-production lines, allowing a clear material-cost-to-productivity balance to be achieved without bespoke adapters. Straightforward fastening and maintenance to minimise downtime Service and routine maintenance are simplified by using a common T20 Torx key and M5x12 fixing screws for secure retention. The standardised fasteners provide reliable clamp force while being easy to access, helping to shorten maintenance intervals. With a defined 90° cutting angle and a configuration offering ten cutting edges, the head is optimised for repeatable shoulder turning and finishing passes, cutting the need for frequent adjustments and supporting continuous operation. Compact design for versatile installation in diverse setups With an overall length of 63 mm and balanced mass (2.945 kg), this tool head is suitable where space is limited yet rigidity cannot be compromised. Its dimensions allow mounting in confined tool turrets or holders without sacrificing the contact stability that larger assemblies provide. The compact envelope supports efficient spindle handling and helps integrate the head into automated change systems or manual setups while maintaining the process reliability expected in industrial turning. Contact Metav Werkzeuge for precise ordering and delivery options from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss the T547TM indexable corner tool head and its fit for specific turning tasks Technical data Article number: T547TM Label: 125 mm corner tool head WNMU 0806 L63 mm Product: Corner tool head Facts Diameter: 125 mm Mounting diameter: 40 mm Overall length: 63 mm Weight: 2.945 kg Cutting edges: 10 Cutting angle: 90° Torx screw: M5x12 Torx key: T20 eClass: 21181015 Special features Compatible with WNMU 0806 indexable inserts Compatible insert manufacturer: Kyocera Brand: Teknik Makina SKU: T547TM FAQ What inserts fit this tool head? The tool head accepts WNMU 0806 indexable inserts, compatible with standard Kyocera grades for turning and finishing. How is the insert secured and which tools are needed? Inserts are secured with M5x12 Torx screws tightened with a T20 key, providing reliable clamping and easy service. Is the head suitable for tight mounting spaces? Yes; the compact 63 mm overall length and standard mounting diameter make the head suitable for restricted turret or holder envelopes. Which cutting angle does the head provide for shoulder operations? The head is configured with a 90° cutting angle, optimised for square shoulder turning and consistent finishes. Can the head be used with Kyocera inserts from existing stocks? Compatibility with Kyocera WNMU 0806 inserts allows direct use of existing insert stocks without additional adapters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of high rigidity, precise 90° cutting geometry and built-in coolant for consistent cycle times and reliable surface finish; order the tool head directly via Metav Werkzeuge or contact our consultants for application support. Eckmesserkopf – 125 mm angled tool head with internal coolant for XNEX 0806 Indexable Inserts by Teknik Makina Eckmesserkopf is a 90° corner turning head designed for secure, coolant-fed machining with XNEX 0806 indexable inserts in demanding production environments. 125 mm diameter for stable machining Internal coolant for improved chip control Compatible with XNEX 0806 inserts (SECO) Robust M4x12.5 fastening with T15 drive Consistent rigidity and repeatable geometry for stable turning The holder body offers a substantial 125 mm diameter, which increases mass at the cutting zone and reduces vibration during interrupted cuts. This enhanced stability leads to more consistent surface finish and extended insert life compared with smaller-diameter alternatives. The unit’s overall length of 60 mm keeps overhang to a minimum, improving stiffness while retaining accessibility for many turning operations. With a nominal mass of 3.155 kg, the construction balances inertial damping and tool change practicality, supporting repeatable results across batches. Built-in coolant for improved process reliability Equipped with internal coolant, the head delivers cutting fluid directly to the insert pocket to improve chip evacuation and thermal control. Direct coolant at the cutting edge reduces built-up edge formation and helps maintain tool life under continuous operation. For shops where coolant-fed machining is standard practice, this feature translates into fewer unscheduled interruptions and steadier cycle times. The design is simple to integrate into existing coolant supply circuits and supports common machining strategies without additional fixtures. Designed for secure clamping and straightforward maintenance The cutting inserts mount in a configuration suited to XNEX 0806 indexable inserts and accept SECO-compatible geometries, ensuring access to a wide range of grades and chipformers. The clamping uses M4x12.5 Torx screws driven with a T15 tool, allowing fast and reliable insert changes while maintaining correct seating force. Ten insert positions are provided to maximise productivity per tool body before a full service cycle is required. Clear mechanical fastening and standardised spares mean downtimes are minimised and maintenance remains predictable. Application fit and practical advantages in production With a defined 90° cutting angle, the head is optimised for corner and face-turning tasks that require square shoulders or precise step features. The geometry simplifies programming and reduces the number of tool setups required for multi-diameter parts. Compatibility with established indexable inserts gives flexibility when selecting grades for different materials or cutting conditions, allowing shops to balance cost per edge with required component tolerances. The compact length also helps where turret or gang-tool space is limited. Contact Metav Werkzeuge for tailored application advice and reliable supply of Teknik Cutting Tools tool heads such as the T848-1TM via Metav Werkzeuge’s technical sales team in Emmerich. Technical data Article number: T848-1TM ECLASS: 21181015 Product type: Eckmesserkopf Manufacturer: Teknik Makina Facts Diameter: 125 mm Overall length: 60 mm Weight: 3.155 kg Cutting angle: 90° Special features Internal coolant For XNEX 0806 indexable inserts Compatible with SECO inserts Number of cutting positions: 10 Fastening screw: M4x12.5 Torx key: T15 FAQ What inserts are compatible with this tool head? The tool head accepts XNEX 0806 indexable inserts and is specified to be compatible with SECO-manufactured insert designs for broad grade selection. Does the head provide coolant to the cutting edge? Yes, the unit features internal coolant that supplies fluid directly to the insert pocket for improved chip evacuation and thermal control. How is the insert secured and what drive is required? Inserts are secured with M4x12.5 Torx screws; a T15 Torx key is used for insertion and removal to ensure correct clamp torque and quick servicing. Is the head suitable for operations requiring a square shoulder? The 90° cutting geometry is specifically suited to square-shoulder and corner turning applications where precise shoulder definition is required. What is the article number for ordering or identification? The article number (SKU) is T848-1TM, which should be quoted for orders and technical enquiries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 125 mm diameter, internal coolant and LNMX 1510 compatibility for precise, reliable turning — order directly from Metav Werkzeuge or contact our consultants for application advice. Square-head tool holder T380-1TM — 125 mm diameter with internal coolant, for LNMX 1510 Indexable Inserts (Teknik Makina) A square-head tool holder engineered for industrial turning and facing operations using LNMX 1510 indexable inserts, designed to deliver stable performance in confined setups. 125 mm cutting diameter Internal coolant supply Fits LNMX 1510 indexable inserts Robust 63 mm overall length Greater rigidity for improved surface finish and repeatability The larger 125 mm diameter and a mass of 3.65 kg provide enhanced structural stability, reducing chatter during heavy cuts. This increased rigidity translates into a more consistent surface finish and tighter tolerances on turned components, which is especially beneficial in batch production or when machining difficult geometries. The robust construction supports sustained high-performance milling and turning cycles without compromising accuracy. Integrated cooling that extends insert life and control The tool head’s internal coolant delivery directs fluid precisely to the cutting zone, reducing thermal load and improving lubrication at the point of contact. This targeted cooling improves chip control and slows thermal wear, which can extend the service life of indexable inserts, reduce unplanned downtime and lower tool consumption over long production runs. For machining operations where temperature control is critical, this feature brings measurable process stability. Broad insert compatibility for streamlined sourcing Designed for LNMX 1510 indexable inserts and compatible with inserts from Korloy, the holder ensures easy procurement and predictable performance across many industrial workflows. Using standardised insert types simplifies inventory management and makes it straightforward to replace cutting edges without altering clamping geometry. The result is less machine idle time and a smoother supply chain for consumables in the workshop. Compact design ideal for tight setups and multiposition turrets With an overall length of 63 mm, the head keeps overhang to a minimum while still delivering the access needed for facing and profiling close to fixtures. The compact footprint makes it suitable for multi-station turrets and compact lathes where space is limited, helping to maintain stiffness and reduce leverage that can otherwise degrade accuracy in constrained setups. Secure clamping and straightforward maintenance Clamping is executed with a Torx T15 key and a M4x12.5 screw, offering reliable, repeatable fastening and simple service procedures. The standardised fastener format allows quick insert changes and predictable torque application, cutting maintenance time and simplifying operator training. This pragmatic approach supports high uptime in production environments where speed and safety are priorities. Designed for consistent industrial performance A 90° cutting angle supports true right-angle turning tasks and straightforward programming in CNC cycles, while the overall build is aimed at continuous industrial use. The combination of dimensional stability, direct coolant feed and compatibility with widely available inserts makes this head a dependable choice for workshops seeking process predictability and efficient tool change routines. For tailored application advice on Teknik Cutting Tools' square-head tool holder T380-1TM and reliable supply from Emmerich, contact Metav Werkzeuge for technical guidance and fast dispatch. Technical Data Article number: T380-1TM Label: 125mm Eckmesserkopf LNMX 1510 L63mm mit Innenkühlung Product type: Square-head tool holder Eclass: 21181015 Facts Diameter: 125 mm Overall length: 63 mm Weight: 3.65 kg Cutting angle: 90° Special features Internal coolant Compatible with LNMX 1510 indexable inserts Suitable for Korloy inserts Torx key size T15 Screw M4x12.5 FAQ What insert type does this holder accept? The holder is specified for LNMX 1510 indexable inserts and is compatible with inserts from Korloy, ensuring ready availability of replacement cutting edges. Is the coolant supplied internally or externally? This square-head tool holder features internal coolant delivery, directing fluid to the cutting zone to improve cooling and chip evacuation. What are the key dimensions for tool setup? Key setup dimensions include a 125 mm diameter and an overall length of 63 mm, which help balance reach and rigidity in constrained turret positions. Which fastener is used for clamping the insert? Insert clamping is secured with a Torx T15 key and an M4x12.5 screw to provide repeatable, secure fastening during production. Is this head suitable for high-volume industrial turning? Yes. The combination of structural mass, internal coolant and compatibility with standard LNMX 1510 inserts makes the tool head suitable for continuous industrial turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact tooling solution that combines repeatable shoulder accuracy with straightforward mounting: the head’s 90° cutting angle and compatibility with LNMT 1306 indexable inserts ensure consistent square cuts, while the robust 40 mm shank and secure M4x10 Torx screw (T15) reduce setup time and vibration. Order or request advice via Metav Werkzeuge for seamless integration. Corner Tool Head (Eckmesserkopf) by Teknik Makina — 90° indexable insert holder The Corner Tool Head (Eckmesserkopf) is a 90° indexable tool head designed for heavy‑duty shoulder and face turning operations using LNMT 1306 inserts. 90° cutting angle for square shoulders Accepts LNMT 1306 indexable inserts 40 mm shank for rigid clamping Consistent square machining with minimal rework The right‑angle geometry delivers a 90° cutting angle that is engineered to produce repeatable square shoulders and accurate face cuts. Using the matching LNMT 1306 indexable inserts, the holder enables predictable chip formation and consistent tool engagement, which reduces the need for rework and polishing passes. For operations where cycle time and first‑pass quality matter, this indexable solution converts insert changes into quick maintenance steps rather than long downtimes. Stable mounting and service‑friendly fastening for reliable production A 40 mm shank diameter offers a sturdy interface with standard toolholders, improving stiffness and reducing deflection under load. The clamping system is secured with a M4x10 Torx screw (T15) for fast, repeatable attachment and straightforward maintenance. Combined with a 125 mm diameter head and a balanced mass of 3.325 kg, the assembly is built to withstand machining forces while maintaining alignment—benefits that translate directly into fewer rejects and longer tool life. Compact form for easy integration and predictable toolpaths With an overall length of 63 mm and a cutting configuration featuring 12 cutting points, the head integrates cleanly into existing turret or toolpost setups without requiring extensive reprogramming. The relatively short overhang and compact geometry reduce vibration and improve surface finish when used for external facing or shoulder cuts. Specifying this holder in production planning supports stable toolpaths and simplifies spare‑parts logistics through standardised insert compatibility. Contact Metav Werkzeuge for a compatibility check and procurement advice on the Teknik Makina Corner Tool Head T232TM; our team in Emmerich will advise on mounting options and delivery times Technical data Article number: T232TM Brand: Teknik Makina For inserts: LNMT 1306 Compatible with inserts manufacturer: ISCAR Core data Diameter: 125 mm Shank diameter: 40 mm Weight: 3.325 kg Cutting angle: 90° Overall length: 63 mm Cutting edges: 12 Special features Indexable corner tool head design Torx screw M4x10, Torx key T15 Suitable for shoulder and face turning SKU T232TM FAQ What inserts fit this tool head? The Corner Tool Head accepts LNMT 1306 indexable inserts; compatibility with ISCAR‑made LNMT 1306 inserts is indicated for straightforward procurement and replacement. Is the holder suitable for heavy‑duty shoulder machining? Yes. The holder’s 90° cutting angle, 40 mm shank and 3.325 kg mass provide the rigidity necessary for heavy‑duty shoulder and face turning operations. Which fastening hardware is required for maintenance? Maintenance and insert changes are performed with the M4x10 Torx screw (T15) specified for the tool head; a T15 Torx key is recommended for secure and repeatable clamping. How does the compact length affect machining stability? The 63 mm overall length reduces overhang and helps control deflection, resulting in improved surface finish and longer tool life when the holder is mounted correctly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise 90° cutting performance combined with an integrated coolant supply and a compact 125 mm diameter design for consistent production output. Order the T208-1TM via Metav Werkzeuge or consult the technical team for application-specific guidance. Eckmesserkopf T208-1TM — indexable corner tool head, 125 mm diameter (Teknik Makina) The Eckmesserkopf T208-1TM is a purpose-built indexable corner tool head for ADKT 1505 indexable inserts, engineered for stable turning operations and improved tool life through internal coolant. 125 mm diameter turning head For ADKT 1505 indexable inserts Integrated internal coolant supply 90° cutting angle for precise corner cuts Reliable chip evacuation and consistent cutting quality The head’s internal coolant delivers coolant directly to the cutting zone, reducing temperatures and improving flank wear characteristics. With a 125 mm diameter and a compact 62 mm overall length, the assembly provides a stiff, vibration-resistant solution that supports reproducible surface finishes and extended insert life. This configuration translates into fewer interruptions for insert changes and more predictable cycle times on production lathes. Fast insert changes and secure clamping for reduced setup time Designed for straightforward maintenance, the tool head uses T15 Torx drive and M4x10 screws to secure inserts, enabling rapid, repeatable seating and torque control. The combination of robust screw fixation and a defined 90° cutting angle ensures stable engagement during face and corner-turning tasks. Operators benefit from reduced setup complexity and shorter machine downtime when service or insert rotation is required. Broad compatibility for workshop standardisation and process planning Compatible with ADKT 1505 indexable inserts and matched to ISCAR insert geometries, the unit helps standardise tooling across mixed-machine environments. At a weight of 0.272 kg, the head minimises added toolholder inertia while remaining rugged enough for industrial turning. Use in series production or small-batch manufacturing supports consistent process parameters and easier tool inventory management. For further technical specifications or to verify fitment in a specific holder, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930. Contact Metav Werkzeuge today to discuss application suitability for the Teknik Makina T208-1TM and arrange procurement or technical consultation. Technical data SKU: T208-1TM Product type: Eckmesserkopf Manufacturer: Teknik Makina Label: 125mm Eckmesserkopf ADKT 1505 L62mm mit Innenkühlung eClass: 21181015 Facts Diameter: 125 mm Overall length: 62 mm Toolholder bore (aufnahme): 40 mm Weight: 0.272 kg Cutting edges: 9 Cutting angle: 90° Torx key: T15 Torx screw: M4x10 Special features Internal coolant supply For ADKT 1505 indexable inserts Compatible with ISCAR inserts Compact, vibration-resistant design FAQ What insert type does the T208-1TM accept? The T208-1TM is specified for ADKT 1505 indexable inserts and is compatible with ISCAR geometries, enabling direct use of standard ADKT 1505 inserts. Is the tool head supplied with internal coolant capability? Yes, the Tek­nik Makina T208-1TM features internal coolant to direct coolant to the cutting zone and support thermal stability. Which fasteners are required for insert clamping? The head uses a T15 Torx drive with M4x10 screws for secure and repeatable insert clamping on the T208-1TM. What are the main dimensional data for planning tool assembly? Key dimensions for the T208-1TM include a 125 mm diameter, 62 mm overall length and a 40 mm toolholder bore. For which applications is this corner tool head intended? The Eckmesserkopf T208-1TM is intended for precision corner and face-turning operations where a 90° cutting angle and coolant-fed cutting improve surface finish and tool life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; eMail: info@metav-werkzeuge.com; Tel: +49 2822 7131930