Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of a robust S40T MTQNR shank, compatibility with TNMG 1604 indexable inserts and a substantial Ø40 mm shaft for stable, vibration‑reduced turning; order reliably via Metav Werkzeuge or consult our specialists for application advice K367TM boring bar — MTWN for TNMG indexable inserts, S40T MTQNR, Ø40 mm shank (Teknik Makina) The K367TM boring bar is an MTWN‑style holder designed for right‑hand turning with TNMG 1604 indexable inserts, suitable for medium to heavy‑duty CNC lathe applications S40T MTQNR shank Ø40 mm Compatible with TNMG 1604 inserts Overall length 300 mm, head Ø50 mm Right‑hand cutting, 107.5° cutting angle Stable machining for consistent component finish The MTWN design delivers a rigid tool geometry that reduces chatter and improves repeatability. With a Ø40 mm shank and the recognised S40T MTQNR interface, the holder provides enhanced clamping stability, which translates into a more consistent surface finish and longer insert life. The specified 107.5° cutting angle optimises the cutting engagement for typical lathe setups and helps maintain dimensional accuracy during extended production runs. Quick insert compatibility and predictable tool setup Compatibility with TNMG 1604 indexable inserts simplifies tool provisioning and shortens setup times on the shop floor. The head diameter of Ø50 mm and the clear designation as an MTWN style holder mean that tool offsets and mounting remain predictable across machines, lowering the risk of errors during tool changes. The right‑hand cutting orientation is explicitly marked to support correct installation and safe operation. Designed for production reliability and easy integration At 300 mm overall length and a measured weight of 2.807 kg, the bar balances reach with rigidity for a range of internal and external turning tasks. The robust construction suits series manufacture where stability and repeatability are priorities; the toolholder form factor is compatible with standard clamping systems used in modern CNC lathes. Where process reliability matters, this solution reduces rework and supports steady throughput. For application guidance or to secure supply of the Teknik Makina MTWN system via Metav Werkzeuge, contact our advisors in Emmerich for tailored recommendations and dependable delivery Technical Data SKU: K367TM ISO designation: S40T MTQNR Type: MTWN for TNMG indexable inserts Manufacturer: Teknik Makina Facts Shaft diameter: 40 mm Cutting height: 60 mm Head diameter: 50 mm Overall length: 300 mm Weight: 2.807 kg Cutting angle: 107.5° Cutting direction: right Special features Compatible insert: TNMG 1604 Style: MTWN indexable insert holder Application: turning on CNC lathes Material / finish: (as supplied by manufacturer) FAQ Which inserts fit this holder? The K367TM boring bar accepts TNMG 1604 indexable inserts; the MTWN pocket is configured for that insert size and geometry. Is the bar suitable for internal turning on lathes? Yes — with an overall length of 300 mm and a Ø40 mm shank the holder is suitable for many internal turning applications where reach and rigidity are balanced. What is the correct mounting orientation? The K367TM is specified for right‑hand cutting; install and set offsets accordingly for reliable cutting performance. How does the S40T MTQNR shank benefit clamping? The S40T MTQNR shank provides a standardised interface that improves clamping stability and repeatable positioning in common toolholders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of stability and insert compatibility for predictable turning performance: the solid S40T MTUNL design delivers high rigidity through a 40 mm shank and a 50 mm body diameter, while compatibility with TNMG 1604 indexable inserts keeps tooling costs predictable—order via Metav Werkzeuge or consult their specialists for application advice S40T MTUNL boring bar — MTUN for TNMG indexable inserts, left-hand The S40T MTUNL is a left-hand boring bar designed for turning operations that require secure clamping of TNMG 1604 indexable inserts and steady cutting behaviour in medium-duty machining. Left-hand cutting orientation 40 mm shank diameter For TNMG 1604 inserts 300 mm overall length Stable cutting for consistent surface finish and longer tool life The substantial 40 mm shank and a 50 mm body diameter create a rigid toolholder that reduces vibration and chatter, producing a more consistent surface finish on turned parts. A stable holder means fewer tool changes and less rework, which contributes directly to greater process efficiency and predictable batch quality. The measured mass of the toolholder helps dampen transient forces during interrupted cuts, so cycle times can be maintained without sacrificing finish. Proven insert compatibility and straightforward geometry Designed for TNMG 1604 indexable inserts, the holder’s MTUN seating ensures repeatable positioning and simple clamping for quick insert changes. The cutting height 60 mm and the tool’s cutting angle 93° maintain the correct approach geometry for conventional turning set-ups, preserving insert life and minimising manual adjustment. Because the design follows common insert standards, spare inserts and replacements are widely available, which lowers logistics complexity and keeps production moving. Practical integration into workshop tooling systems Marked with the ISO designation S40T MTUNL, the holder is ready for standard lathe tool posts that accept a 40 mm shank; the 300 mm overall length gives reach for typical bore and face-turning tasks while retaining stiffness where it matters. At a weighed 2.852 kg, the component balances mass and handling for straightforward mounting and removal. The straightforward configuration supports efficient tool inventory management and reduces set-up time during changeovers. For procurement or technical clarification on the Teknik Makina MTUN holders, contact Metav Werkzeuge in Emmerich for tailored advice and reliable delivery to the workshop; e-mail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: K524TM ISO designation: S40T MTUNL Type: MTUN for TNMG indexable inserts Cutting direction: left Compatible insert: TNMG 1604 Core data Shank diameter: 40 mm Overall length: 300 mm Body diameter: 50 mm Cutting height: 60 mm Weight: 2.852 kg Cutting angle: 93° Special features For TNMG 1604 indexable inserts MTUN holder geometry Left-hand orientation Suitable for conventional turning operations SKU: K524TM FAQ Which inserts fit this holder? The holder accepts TNMG 1604 indexable inserts; the MTUN seating secures the insert for repeatable positioning in the Teknik Makina S40T MTUNL boring bar (SKU K524TM). Is the cutting direction left or right? This model is specified for a left-hand cutting direction and is intended for left-hand turning operations. What shank size is required for the tool post? The boring bar uses a 40 mm shank (ISO designation S40T MTUNL) and suits tool posts that clamp a 40 mm holder. How does the geometry affect insert life? The combination of correct cutting height and a 93° cutting angle keeps the insert load balanced, which helps to extend insert life and maintain consistent chip formation. What identifier should be used when ordering spares? Use SKU K524TM and ISO designation S40T MTUNL when ordering to ensure the correct MTUN boring bar is supplied. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a combination of rigid clamping and insert compatibility: the 40 mm shank and CNMG 1204 compatibility deliver stable boring with reduced vibration, while the 300 mm overall length enables deeper reaches. Order the Teknik Makina PCLN boring bar directly via Metav Werkzeuge or consult the Metav team for specification advice. Boring bar PCLN for CNMG Indexable Inserts (S40T PCLNR) — Teknik Makina The Boring bar PCLN for CNMG Indexable Inserts is a right-hand external turning holder designed for secure boring operations with CNMG 1204 inserts, optimised for setups without internal coolant Right-hand cutting direction, stable performance For CNMG 1204 indexable inserts 40 mm shank for secure clamping 300 mm overall length for deep reach Achieve stable machining with a robust shank design A solid 40 mm shank diameter combined with a 50 mm tool diameter and balanced mass (approx. 1.825 kg) reduces vibration and improves roundness in bored features. The S40T PCLNR geometry is engineered for rigid clamping in standard tool posts; this stability translates into consistent surface quality and extended insert life. Where process reliability and reproducible results matter, the mechanical design supports higher material removal rates without compromising dimensional accuracy. Minimise tooling changes through standard insert compatibility Compatibility with CNMG 1204 indexable inserts makes the toolholder a pragmatic choice for shops that favour widely available carbide grades. The PCLN configuration and the 95° cutting angle give a neutral cutting stance suited to external boring and finishing passes. As the holder is specified without coolant, it is intended for operations where flood or through-tool coolant is not required; users can pair it with appropriate insert grades and cutting parameters to achieve the desired surface finish and tool life while avoiding internal coolant pathways. Designed for workshop integration and efficient clamping The 300 mm overall length provides extended reach for deep bores while the 55 mm cutting height ensures the cutting edge aligns correctly with standard tool posts. The right-hand orientation supports conventional lathe setups and simplifies tool change routines in mixed-production environments. Combined with Metav’s sourcing model — a European stock point and quality filter — the component fits into procurement strategies that demand predictable supply and compatibility with existing insert inventories. Discuss the Teknik Makina PCLN boring bar with Metav Werkzeuge to assess fit for specific machines and workpieces; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for tailored advice and order support Technical Data Article number: P344TM ISO designation: S40T PCLNR ECLASS: 21180806 Brand: Teknik Makina Facts Diameter: 50 mm Shank diameter: 40 mm Overall length: 300 mm Cutting height: 55 mm Cutting angle: 95° Weight: 1.825 kg Direction: right Special features For inserts: CNMG 1204 Designation (EN): PCLN for CNMG Indexable Inserts Feature: without coolant FAQ Which indexable inserts fit this tool? The boring bar accepts CNMG 1204 indexable inserts; the PCLN configuration is matched to that insert size for reliable seating and repeatable cutting geometry. Is this holder suitable for coolant-through operations? No, the holder is supplied without coolant and is intended for applications where internal coolant is not required or external cooling methods are used. What is the ISO designation and how does it affect clamping? The S40T PCLNR ISO designation describes the shank and holder geometry; it indicates a 40 mm shank and the PCLN pocket form, ensuring compatibility with standard clamp systems and predictable positioning. What are the primary dimensional limits to consider before purchase? Key dimensions are 50 mm diameter, 40 mm shank, 300 mm overall length, and a 55 mm cutting height; confirm these against the machine tool envelope and turret clearance. Is the holder right-hand or left-hand? The tool is configured for a right-hand cutting direction, suitable for conventional external turning and boring on standard lathes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid design and indexable-insert compatibility for reliable fine internal finishing; the combination of a 25 mm shank, 189 mm cutting length and insert-based system supports consistent productivity and low downtime. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Boring bar THKB136TM – indexable-insert boring tool for fine machining (Ø 40 mm, CCMT 0602) by Teknik Makina The Boring bar THKB136TM is a purpose-built internal boring tool for precision finishing in turning applications, engineered for tight tolerances and stable chip control Fine finish to 0.01 mm Accepts CCMT 0602 inserts Ø 40 mm cutting diameter 25 mm shank, 245 mm overall length Deliver consistent finishes with measurable tolerances The tool is designed to deliver a fine finish down to 0.01 mm, making it suitable for precision internal machining where reproducible surface quality is mandatory. Using an indexable-insert system ensures repeatable cutting geometry; this stability reduces the need for secondary operations and lowers scrap rates. Clear numerical targets, such as the achievable tolerance and provided cutting diameters, create a verifiable basis for process planning and quality control. Rigid geometry reduces vibration and improves tool life A 25 mm shank combined with an overall length of 245 mm and a cutting length of 189 mm provides a balanced ratio between reach and rigidity. This geometry limits deflection during boring cycles, which in turn preserves insert life and enhances dimensional accuracy. The unit's mass (approx. 1.723 kg) contributes to damping, helping to maintain a constant cutting force and stable chip formation across the intended bore sizes. Versatile insert system for efficient workshop logistics Compatibility with CCMT 0602 indexable inserts allows quick tool reconditioning and a consistent cutting edge across different batches. The bar supports a nominal Ø 40 mm cutting diameter with a maximum cutting capability up to 50 mm, covering a common range of internal finishing tasks. Standardising on widely available inserts lowers stocking complexity and reduces machine downtime during insert changes, improving overall throughput. Practical benefits for production planning and setup The combination of measurable parameters and a standard insert interface simplifies fixture and holder selection, while the tool's specifications enable predictable cycle times. The design supports integration into existing boring toolholders that accept a 25 mm shank, making retrofits straightforward. For process engineers, the clear data on diameter limits, cutting length and repeatable finishing tolerance supports confident machining parameter selection and risk mitigation. Contact Metav Werkzeuge for tailored application advice and to arrange delivery of the Teknik Makina THKB136TM — our Emmerich team is available to discuss suitability, delivery times and integration into existing setups. Technical data Article number: THKB136TM Manufacturer: Teknik Makina Type: Boring tool for fine machining ECLASS: 21041590 Numbers / Core technical data Cutting diameter max: 50 mm Nominal cutting diameter: 40 mm Shank diameter: 25 mm Cutting/shank length: 189 mm Overall length: 245 mm Weight: 1.723 kg Fine machining tolerance: 0.01 mm Special features / Versions For indexable inserts CCMT 0602 Designed for fine internal finishing Indexable-insert system for quick replacement Suitable for precision turning applications FAQ What insert type does this boring bar use? The THKB136TM is designed to accept CCMT 0602 indexable inserts, enabling fast replacement and consistent cutting geometry. What bore sizes can be machined with this tool? The tool covers a nominal cutting diameter of Ø 40 mm and can be used up to a maximum cutting capability of 50 mm depending on application parameters. How does the shank size affect setup? A 25 mm shank gives a robust connection to standard boring holders; for secure clamping, select holders rated for a 25 mm diameter shank to maintain rigidity and accuracy. What level of surface precision is achievable? The design targets fine finishing down to 0.01 mm, providing a reliable baseline for achieving tight dimensional tolerances in internal machining. Is the THKB136TM suitable for long-reach boring? With an overall length of 245 mm and a cutting length of 189 mm, the bar balances reach and stiffness; for extended-reach requirements, assess toolholder rigidity and process parameters to avoid deflection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a tool that combines high repeatability with straightforward insert compatibility: the compact design delivers fine finishing down to 0.01 mm, supports a maximum cutting diameter of 65 mm and accepts standard CCMT inserts for fast set-up. Order directly via Metav Werkzeuge or consult the Metav specialists for application advice. Boring tool for fine finishing THKB140TM by Teknik Makina — 50 mm nominal diameter, 0.01 mm finish accuracy The Boring tool for fine finishing THKB140TM is an internal boring bar engineered for precision finishing in CNC turning applications, delivering stable performance for batch and single-part production. Fine finishing capability to 0.01 mm Compatible with CCMT 09T3 inserts Shank Ø 32 mm for rigid clamping Max cutting diameter 65 mm Keep tolerances tight with reliable fine finishing The THKB140TM is designed to produce consistent part quality by enabling finish passes with a nominal repeatability down to 0.01 mm. This level of accuracy is achieved through a balanced combination of a rigid tool body and a long cutting reach, which together reduce deflection during light cuts. Where small surface deviations matter, the controlled geometry of the boring bar ensures that finishing cuts remove just the right amount of material, so inspection intervals are reduced and downstream processes remain predictable. The result is fewer reworks and a more efficient production flow. Stable clamping that cuts chatter and extends tool life A robust shank with a diameter of Ø 32 mm and an overall length of 190 mm provides the axial and radial stiffness required for vibration‑free machining when finishing internal bores. With a cutting length of 130 mm and a maximal cutting diameter of 65 mm, the tool maintains a secure interface with the machine spindle or tool post, which keeps cutting forces steady and minimises micro‑movement. Reduced vibration not only improves surface finish but also prolongs the service life of both inserts and holder, supporting longer uninterrupted production runs. Fast set-up through standard insert compatibility The holder is prepared for CCMT 09T3 indexable inserts, a widespread carbide grade and geometry in finishing applications. Using standard CCMT 09T3 inserts means tool changes and re‑grinds are quicker, tooling inventory is easier to manage and downtime is minimised. The insert pocket and clamping system are designed so that insert seating is positive and repeatable; consequently, interchangeability between identical holders is straightforward and set-ups can be standardised across a shop floor. Integrates smoothly into workshop routines and production planning With a nominal diameter of 50 mm, a weight of 2.135 kg and compact overall dimensions, this boring bar is suitable for integration into conventional lathe and CNC turning cells without significant fixturing changes. The design supports fine finishing operations where surface quality and dimension control are priorities, and the combination of length and stiffness is optimised to keep cutting forces predictable. Metav’s supply chain and quality screening in Emmerich provide traceable sourcing and consistent availability, which supports reliable scheduling for medium and long production runs. Contact Metav Werkzeuge to discuss application suitability for the Teknik Makina THKB140TM and arrange specification details or delivery directly from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: THKB140TM Manufacturer: Teknik Makina ECLASS: 21041590 Core specifications Fine finishing tolerance: 0.01 mm Max cutting diameter: 65 mm Nominal diameter: 50 mm Overall length: 190 mm Cutting length: 130 mm Shank diameter: 32 mm Weight: 2.135 kg Features & compatibility For CCMT 09T3 indexable inserts Intended for fine finishing internal boring Suitable for CNC turning applications Brand: Teknik Makina FAQ What insert type does the tool use? The THKB140TM accepts CCMT 09T3 indexable inserts; this allows for fast replacement and common insert inventory across finishing tooling. What level of finishing accuracy is achievable? The boring bar is specified for fine finishing with a repeatability target of 0.01 mm, suitable for tight tolerance internal bores. What are the maximum and nominal diameters for use? Maximum cutting diameter is 65 mm while the nominal holder diameter is 50 mm, providing a balance of reach and stiffness. What are the key dimensions that affect setup? Relevant dimensions are overall length 190 mm, cutting length 130 mm and shank diameter 32 mm, which determine clamping and overhang requirements. Is the tool suitable for series production? Yes — the combination of standard insert compatibility and a rigid shank design makes the holder appropriate for repeated finishing operations in production environments. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah. 422 Nolu Sokak No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a combination of precision finishing, robust shaft design and compatibility with standard CCMT inserts for consistent internal-surface quality; order the tool via Metav Werkzeuge or consult our specialists for application-specific advice. Fine finishing boring tool by Teknik Makina — Ø50 mm, compatible with CCMT 09T3 inserts A Fine finishing boring tool engineered for high-precision internal finishing in CNC and lathe operations, offering a long cutting length for deep bores. Fine finishing tolerance 0.01 mm Compatible with CCMT 09T3 inserts Shaft Ø32 mm for increased rigidity Max cutting diameter 65 mm Precise finishing for demanding internal surfaces This machining solution is designed to deliver repeatable fine finishing with a verified tolerance of 0.01 mm, making it suitable for applications where surface quality and dimensional fidelity are critical. The tool’s nominal diameter of Ø50 mm and its extended cutting length 220 mm mean fewer insert changes and longer uninterrupted operations when working on deep bores. The combination of a robust shaft Ø32 mm and a total length of 280 mm provides improved stability that reduces chatter, which in turn delivers better surface finish and less post-process rework. Productivity gains through proven tool geometry With a maximum cutting capacity of 65 mm, the boring holder supports efficient material removal while preserving finishing quality. The holder is specified for CCMT 09T3 indexable inserts, an industry-standard grade that balances wear resistance and edge sharpness for finishing passes. Using standard inserts simplifies tooling logistics and reduces set-up times. The tool’s mass of 3.383 kg contributes to steadier cutting dynamics on medium and heavy-duty machines, allowing for slightly higher feed stability without sacrificing the delicate controls needed for finishing. Application range and user advantages Built for CNC shops, toolrooms and contract manufacturers, this holder is best applied where internal diameters require consistent roundness and micro-accuracy. The long effective cutting length supports deep-bore finishing in components such as hydraulic bodies, sleeves and precision housings. Because the design accepts widely available CCMT inserts, workshop teams benefit from broad insert availability and predictable performance, which helps keep throughput steady and inventory manageable. Integration, maintenance and quality assurance The boring holder’s compatibility with standard inserts and its straightforward clamping geometry make mounting and index changes quick and intuitive. Regular inspection of insert seating and torque on the clamping screws will preserve the tool’s precision across production runs; replacement inserts should match the CCMT 09T3 designation for intended finish behaviour. For application-specific parameters such as cutting speeds and feeds, Metav Werkzeuge’s technical advisers can provide guidance to match machine rigidity and workpiece material, helping to achieve the best balance between surface integrity and productivity. For applications demanding precise internal finishing, select the Teknik Cutting Tools boring solution and contact Metav Werkzeuge for tailored machining recommendations and reliable supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: THKB142TM Manufacturer: Teknik Makina Product name: Ausdrehwerkzeug für die Feinbearbeitung Core measurements Nominal diameter: 50 mm Max cutting diameter: 65 mm Overall length: 280 mm Cutting length (shaft): 220 mm Shaft diameter: 32 mm Fine finishing tolerance: 0.01 mm Weight: 3.383 kg Compatible inserts: CCMT 09T3 Features / Special characteristics Designed for fine internal finishing Accepts CCMT 09T3 indexable inserts Long cutting reach for deep bores Robust shaft for reduced vibration FAQ What materials is this boring holder suitable for? This fine finishing boring tool is intended primarily for metal finishing operations; compatibility with specific materials depends on the chosen CCMT insert grade and cutting parameters. Which insert type must be used with the tool? The holder is specified for CCMT 09T3 indexable inserts; using the correct grade and geometry of CCMT inserts ensures the intended finishing performance. How deep can this tool reach for finishing operations? The effective cutting length of the tool’s shaft is 220 mm, with an overall length of 280 mm, allowing deep-bore finishing where required. What tolerance can be expected from the finished bore? Designed for fine finishing, the tooling supports a finishing capability down to 0.01 mm under appropriate machine and process conditions. Is the tool suitable for high-speed finishing? High-speed suitability depends on machine rigidity, insert selection and cutting parameters; the holder itself is configured to improve stability through its shaft Ø32 mm design. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of compact dimensions, internal coolant and a 90° cutting geometry for reliable, repeatable machining — order the tool head directly via Metav Werkzeuge or contact our consultants for material‑specific advice. Eckmesserkopf T650-1TM — 50 mm corner tool head with internal coolant by Teknik Makina The Eckmesserkopf is a compact corner tool head designed for orthogonal operations with SPMT 1204 indexable inserts, offering controlled coolant delivery and a short overall length for confined setups. 50 mm diameter for compact setups Internal coolant for improved chip control Four cutting edges for extended service intervals 90° cutting angle for orthogonal turning Consistent chip evacuation for uninterrupted machining The compact head delivers controlled cooling directly to the cutting edge via internal coolant, reducing heat at the cutting zone and improving tool life. Designed around a 50 mm diameter, the short L40 mm overall length keeps overhang to a minimum, which helps to reduce deflection and chatter. This combination enables more stable cutting forces when using SPMT 1204 inserts and supports sustained, high‑quality surface finishes in short‑reach applications. Fast indexable insert changes and secure mounting Compatibility with SPMT 1204 indexable inserts and the use of a Torx T20 drive make insert replacement straightforward and repeatable. The head is secured with M5x12 Torx screws that ensure consistent clamping force and alignment. Fewer handling steps during tool changes translate into reduced downtime and predictable cycle times on CNC lathes and turning centres, delivering measurable efficiency gains across production batches. Stable geometry for precision and repeatability With a defined 90° cutting angle and four cutting edges, the design emphasises geometric stability and prolonged tool usage between indexing. The robust construction and balanced mass distribution—weighting approximately 0.362 kg—support precise, repeatable cuts in short‑reach external operations. The tool head’s form factor is especially suited to setups where rigidity and positional accuracy are critical for maintaining tolerances. Practical assembly and workshop integration The head’s compact profile and standardised fastening reduce fixturing complexity for retrofit or new toolpost arrangements. Internal coolant routing is designed to integrate with common machine supplies to ensure efficient chip control without elaborate modifications. Assembly and maintenance use familiar workshop tools and procedures, simplifying stock management and operator training while keeping set‑up times predictable. For tailored procurement or technical consultation on the Teknik Makina T650-1TM, contact Metav Werkzeuge for specialist advice and reliable supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: T650-1TM ECLASS: 21181015 Product type: Eckmesserkopf Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.362 kg Cutting edges: 4 Cutting angle: 90° Special features Compatible inserts: SPMT 1204 Internal coolant: yes Torx key: T20 Torx screw: M5x12 Manufacturer: Teknik Makina FAQ Which inserts are compatible with this tool head? The head is designed for SPMT 1204 indexable inserts; the geometry and pocket accept standard SPMT 1204 sizes for reliable seating and accurate cutting. Is coolant delivered directly to the cutting edge? Yes, the internal coolant channel supplies coolant to the cutting zone, improving chip evacuation and extending insert life for the Teknik Makina Eckmesserkopf T650-1TM. What operations suit this corner tool head best? The 90° cutting angle and compact length make the head ideal for orthogonal turning and short‑reach external facing where rigidity and surface quality matter. Which fastening hardware is used for insert clamping? Insert clamping uses M5x12 Torx screws operated with a Torx T20 drive to ensure consistent clamping and repeatable seating. Can this head be used in confined toolpost setups? The compact 50 mm diameter and 40 mm overall length are optimised for tight installations, where reduced overhang helps maintain stability and accuracy. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-stability turning solution that combines 50 mm body diameter, 90° cutting geometry and compatibility with WNEX 0806 indexable inserts for reliable corner profiling; order directly via Metav Werkzeuge or consult our specialists for application advice. T771TM 50 mm Corner Turning Head – for WNEX 0806 Indexable Inserts (Teknik Makina) The corner turning head is engineered for precise corner and profile turning with WNEX 0806 indexable inserts in compact toolholders and turret installations 50 mm diameter for stable turning 40 mm overall length for compact setups 90° cutting angle for corner profiling Compatible with WNEX 0806 indexable inserts Stable geometry that improves process reliability The holder’s 50 mm body and 40 mm overall length create a rigid mounting that reduces vibration and deflection during machining, which directly improves surface finish and dimensional repeatability. The 90° cutting angle is ideal for cornering and profile operations where a clear shoulder and accurate corner form are required. Compatibility with WNEX 0806 indexable inserts standardises tooling across multiple machines, reducing changeover times and inventory complexity; the result is a measurable gain in process stability and fewer scrap parts. Quick insert clamping and straightforward serviceability Designed for efficient maintenance, the head secures inserts using an M4x10 Torx screw and requires a T15 Torx key, allowing rapid insert changes and minimal downtime. The use of indexable inserts eliminates the need for regrinding, and the head’s accessible screw layout supports safe, repeatable clamping. Lightweight at 0.285 kg, the component is easy to handle during set-up while still providing sufficient mass to dampen cutting vibrations, helping to protect both the insert and the machine spindle. Compatibility and application benefits for diverse workshops Manufactured by Teknik Makina and suitable for YG-1 supplied WNEX 0806 inserts, this tool head fits production and job-shop environments where flexibility and inventory efficiency matter. The design supports multi-edge insert use, extending tool life and reducing cost per part. By standardising on a reliable indexable system and a robust holder, shops can simplify tool management, increase uptime and achieve consistent part quality across batches and machine types. For precision corner turning with proven compatibility, contact Metav Werkzeuge for application-specific advice or to arrange supply of the T771TM corner turning head; Metav’s specialists in Emmerich can help confirm suitability for the intended turning tasks and ensure timely delivery Technical Data SKU: T771TM Label: 50mm Eckmesserkopf WNEX 0806 L40mm Manufacturer: Teknik Makina Compatible inserts: WNEX 0806 (YG-1) Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.285 kg Cutting angle: 90° Cutting edges: 5 Torx screw: M4x10 Torx key: T15 eClass: 21181015 Special features Product type: Corner turning head Suitable for indexable inserts Compatible insert manufacturer: YG-1 Intended use: corner and profile turning SKU identification: T771TM FAQ What inserts are compatible with this turning head? The turning head accepts WNEX 0806 indexable inserts; compatibility is specified for inserts supplied by YG-1 and the holder is designed to locate and clamp these types reliably. How is the insert secured in the holder? Inserts are fastened with an M4x10 Torx screw; the required key for removal and fitment is T15, allowing quick and repeatable insert changes. Is this holder suitable for heavy-duty turning? The holder’s 50 mm diameter and robust geometry provide good rigidity for many turning tasks; for very heavy cuts consult Metav Werkzeuge to confirm suitability for specific machine and process parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The compact design and built-in coolant channel deliver consistent edge life and stable corner turning, while the 50 mm diameter and 40 mm overall length keep setups space-efficient; order the tool directly via Metav Werkzeuge or consult the Metav specialists for process integration. Corner tool head T315TM — 50 mm diameter, internal coolant, for WNMU 0706 indexable inserts (Teknik Makina) Corner tool head T315TM is a compact 50 mm turning head designed for precision corner operations using WNMU 0706 indexable inserts, combining small envelope and coolant support for stable metalcutting. 50 mm head diameter Internal coolant supply Compatible with WNMU 0706 inserts Compact 40 mm overall length Precision performance for consistent finishing The short, rigid construction of this holder gives repeatable positioning and reduced vibration for fine finishing operations. The 50 mm diameter and robust geometry focus cutting forces close to the spindle, which improves tool life and surface quality when using WNMU 0706 indexable inserts. This results in fewer insert changes and more predictable process windows, supporting leaner machining cycles and higher machine uptime. Integrated coolant and secure clamping reduce downtime An internal coolant channel directs cutting fluid precisely to the cutting edge, aiding chip evacuation and heat control for longer insert life. The clamping system uses a M5x12 Torx screw secured with a T20 key, enabling quick and reliable insert changes with consistent clamping torque. The compact 40 mm overall length and 22 mm shank keep the toolholder stable in tight toolpacks, shortening setup times and lowering the risk of run-out related rejects. Broad compatibility and workshop practicality Compatibility with WNMU 0706 inserts and recognition of Sumitomo as a matching insert manufacturer make integration into existing tooling setups straightforward. The holder’s 90° cutting geometry supports standard cornering applications across common ferrous and non-ferrous turning tasks, while the compact form factor helps maximise turret capacity. The build quality from Teknik Makina ensures reliable repeatability in serial production environments and easier tool management for procurement teams. Contact Metav Werkzeuge for a tailored tooling recommendation and fast supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for consultation and order processing Technical Data Article number: T315TM E-class: 21181015 Label: 50mm Eckmesserkopf WNMU 0706 L40mm mit Innenkühlung Core specifications Diameter: 50 mm Overall length: 40 mm Shank diameter: 22 mm Cutting angle: 90° Number of cutting edges: 5 Materials & features Internal coolant: yes Compatible inserts: WNMU 0706 Compatible insert manufacturer: Sumitomo Torx key: T20 Torx screw: M5x12 Manufacturer: Teknik Makina Product type: Corner tool head FAQ What inserts fit this tool head? The tool head accepts WNMU 0706 indexable inserts; the design is intended for those insert geometries and compatible Sumitomo variants. Does the holder provide internal coolant? Yes — the Corner tool head T315TM features internal coolant supply to the insert pocket to improve chip control and thermal stability. Which fastening hardware is required for insert clamping? Clamping uses an M5x12 Torx screw tightened with a T20 key, providing consistent and serviceable clamping torque for secure insert fixation. Is the holder suitable for tight turret pockets? With a 40 mm overall length and 22 mm shank, the holder is designed for compact installations and efficient use of turret space. What cutting angle does the tool head offer? The tool head presents a 90° cutting geometry suitable for standard corner-turning tasks and related finishing operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precise 90° cutting solution paired with broad compatibility: the combination of a 90° cutting angle, a Ø22 mm shank and compatibility with SECO XOMX 1806 inserts improves process reliability and reduces rework. Order via Metav Werkzeuge for fast supply and expert advice. Corner milling head T520TM (90° right-angle cutter, for XOMX 1806 inserts) — Teknik Makina The Corner milling head T520TM is a 90° right-angle cutter head designed for indexable inserts, intended for accurate face and shoulder milling in CNC and milling centre setups 90° cutting angle for precise right-angle milling Compatible with SECO XOMX 1806 inserts Ø22 mm shank for secure clamping Torx M4.5x11 screw with T15 key included Accurate right-angle milling that reduces setup time The head provides a 90° cutting angle that is engineered to deliver true shoulders and perpendicular faces with minimal correction. Using inserts from the XOMX 1806 family (compatible with SECO standards) simplifies tool sourcing and changeover, because standard indexable inserts fit directly. The compact Ø50 mm body and controlled overall length make the unit suitable for tight envelope requirements, while the measured dimensions contribute to predictable toolpaths and reduced secondary finishing — a clear benefit where cycle time and first-pass accuracy matter. Rigid mounting and reliable clamping for consistent finishes A robust Ø22 mm shank ensures stable clamping in standard toolholders and reduces vibration during cutting, which supports longer insert life and a better surface finish. Clamping integrity is secured via the specified Torx M4.5x11 screw, tightened with a T15 key, offering repeatable torque and simple maintenance routines. At a nominal mass of 0.337 kg, the assembly balances rigidity with manageable inertia, aiding high-speed indexing and safe handling when loading into the spindle. These measurable characteristics translate into fewer interruptions and more predictable production runs. Practical use, maintenance and application guidance The right-angle head is intended for face and shoulder milling where a 90° approach is required; it is optimised for the XOMX 1806 insert format and is best combined with matching insert grades for the workpiece material. Routine checks of the Torx fastening and clean contact faces are advised to maintain concentricity and prolong service life. For machining strategies, pair the head with stable holders and moderate axial engagement on hard materials to extend insert life. Where specific material allowances or cutting data are required, consult technical feed and speed charts and align insert grade to the substrate. For application support or to secure available stock of the Teknik Makina T520TM corner milling head, contact Metav Werkzeuge for tailored advice and prompt dispatch — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: T520TM Manufacturer: Teknik Makina Compatible inserts: XOMX 1806 (SECO) Cutting angle: 90° Torx screw: M4.5x11 Facts Diameter: 50 mm Shank diameter: Ø22 mm Total length: 45 mm Weight: 0.337 kg Number of cutting edges: 5 Special features Compatible with SECO XOMX 1806 indexable inserts Torx key size: T15 Right‑angle milling application SKU: T520TM FAQ What insert type does the head accept? The corner milling head accepts XOMX 1806 indexable inserts compatible with SECO standards; the T520TM is specified for that insert format to ensure correct fit and clamping. Which clamping hardware is supplied or required? Clamping is achieved with a Torx M4.5x11 screw tightened using a T15 key; the specified hardware secures the insert seat and ensures repeatable torque for the T520TM. Is the shank suitable for standard toolholders? The unit uses a Ø22 mm shank, which is compatible with holders made for that diameter and provides a secure, rigid mounting for reliable machining. What machining tasks is this head best for? The right‑angle 90° geometry is suited to face and shoulder milling where square corners and perpendicular faces are required, particularly in CNC milling centres and modular tool setups. Who supplies spare parts and technical advice? Metav Werkzeuge supplies the Teknik Makina T520TM and can provide spare screws, keys and application guidance; contact details are available for ordering and technical consultation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust tool holder that pairs compatibility with APKT 1705 indexable inserts and a defined 90° cutting angle for reliable corner turning. With a 50 mm body diameter and a 22 mm shank, the design offers stable clamping and predictable machining results — order directly via Metav Werkzeuge or consult our specialists for application support. Corner turning head – tool holder for APKT 1705 indexable inserts, 90° – Teknik Makina A Corner turning head designed as a compact tool holder for turning and profiling operations with APKT 1705 indexable inserts, optimised for precise corner work in workshop and CNC environments Corner turning head for APKT 1705 inserts 90° cutting angle for defined corner profiling 50 mm diameter body, 22 mm shank Secured with M4x10 Torx screw and T15 key Stable geometry for predictable machining results The holder’s 50 mm diameter body and 22 mm shank create a rigid connection between machine and insert that reduces vibration and improves surface finish. The defined 90° cutting angle ensures repeatable corner profiles and simplifies programming for CNC turning cycles. Specified mass and dimensions contribute to balanced rotation and steady tool behaviour, which translates into reduced tool chatter and more consistent tolerances on finished parts. Fast insert changes and secure clamping Prepared for APKT 1705 indexable inserts and compatible with Taegutec variants, the holder relies on a single M4x10 Torx clamping screw and a T15 key for swift insert replacement. The simple clamping interface minimises downtime during index changes and inspection. For workshops that run mixed batches, the standardised screw and key ensure routine maintenance is efficient and safe without specialised tooling. Compact form factor suited to workshop and CNC use With an overall length of 45 mm and a compact body, the tool holder is ideal where access is limited or where tool overhang must be kept minimal. The design accommodates five cutting edges, enabling multiple indexing operations before replacement is required and extending effective tool life. The combination of compact dimensions and multiple usable edges supports higher throughput on small to medium lathes as well as CNC turning centres. Reliability, traceable supply and workshop confidence The construction is optimised for everyday industrial use: secure clamping, standardised fasteners and clear compatibility reduce installation errors and support process stability. Paired with a reliable supply chain, procurement from an experienced partner reduces risk of downtime. Metav’s distribution from Emmerich acts as a quality filter for the European market, offering consistent availability and product traceability for production planning and stock management. Contact Metav Werkzeuge for application advice, compatibility checks and to secure supply from Emmerich — speak to our consultants for detailed technical guidance or to discuss ordering options. Technical data Article number: T552TM Manufacturer: Teknik Makina Designation: Corner turning head for APKT 1705 indexable inserts Compatible insert type: APKT 1705 Compatible insert manufacturer: Taegutec Torx screw: M4x10 Torx key size: T15 Body diameter: 50 Shank (clamping) diameter: 22 Overall length: 45 Cutting edges: 5 Cutting angle: 90 Weight: 0.362 kg Core dimensions Diameter: 50 mm Shank diameter: 22 mm Overall length: 45 mm Weight: 0.362 kg Cutting angle: 90° Cutting edges: 5 Special features For APKT 1705 indexable inserts Compatible with Taegutec inserts M4x10 Torx clamping screw T15 Torx key Compact 45 mm design Corner tool holder geometry SKU T552TM FAQ What inserts fit this holder? The holder accepts APKT 1705 indexable inserts; compatible variants from Taegutec are explicitly supported and are listed in the technical data for the T552TM tool holder. How is the insert secured in the tool? Insertion and clamping are performed with the supplied clamping interface using an M4x10 Torx screw tightened with a T15 key to ensure secure fixing and repeatable seating. Is the tool suitable for CNC turning centres? Yes — the compact form, 45 mm overall length and robust shank provide the rigidity required for CNC turning applications and confined tool stations. How many edges can be used before insert replacement? This holder is specified for inserts with five cutting edges, enabling multiple indexing operations before the insert itself needs replacement. What are the key dimensions to check for machine compatibility? Critical dimensions are the 50 mm body diameter and the 22 mm shank diameter; confirm the machine’s tool post or turret accepts a 22 mm shank for proper seating. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-stability cutting head that combines a 50 mm diameter and internal coolant for consistent 90° corner machining; order directly via Metav Werkzeuge or request technical advice to ensure immediate fitment to existing toolholders. Corner tool head T240-1TM – 50 mm diameter, internal coolant, for APMT 0903 inserts (Teknik Makina) The Corner tool head T240-1TM is a compact cutting head engineered for precision 90° corner operations using APMT 0903 indexable inserts, offering stable performance in industrial machining contexts. 50 mm diameter, compact 40 mm overall length Internal coolant for improved chip evacuation Compatible with APMT 0903 indexable inserts Torx T8 screw drive, M2.5×5.5 fastening screw Stable geometry for repeatable corner cuts The robust 50 mm tool body provides a stable platform for 90° cuts, delivering consistent cutting geometry that reduces vibration and improves surface finish. Thanks to the head’s compact 40 mm overall length, the centre of mass is close to the holder, which aids in maintaining run-out and repeatability during batch production. This stability translates into less rework and tighter tolerances on machined edges, supporting quality-oriented workflows in production and jobbing shops. Internal coolant that enhances tool life and process reliability Integrated internal coolant channels direct cutting fluid right to the cutting zone, improving chip evacuation and cooling the insert flank. The focused coolant flow helps prevent built-up edge and reduces thermal loading on the insert, extending tool life and stabilising cutting forces. For processes where tool-change frequency impacts throughput, this coolant-assisted performance increases uptime and contributes to a more predictable machining cycle. Secure clamping and straightforward fastening Clamping relies on a Torx-driven fastening system with Torx T8 and an M2.5×5.5 screw, ensuring a reliable and repeatable seat for indexable inserts. The head accepts APMT 0903 inserts and is compatible with inserts from Korloy, enabling quick reconditioning and inventory alignment. At a mass of 0.348 kg, the unit is light enough to limit imbalance effects while being substantial enough to dampen cutting chatter. The standardised screw interface supports fast insert replacement with commonly available tools. Practical fitment and workshop advantages This tool head is intended for integration into machining setups that require a defined 90° cutting angle with indexable insert technology. The design reduces setup time through standard insert compatibility and the use of widely available Torx fixation; this simplifies spare-part logistics and operator training. For buyers looking to centralise tooling purchases, the head’s standard dimensions and mounting features support quick deployment across multiple machines and fixtures, improving operational flexibility. For reliable 90° corner machining with internal coolant, contact Metav Werkzeuge for ordering and tailored technical advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T240-1TM Manufacturer: Teknik Makina Product type: Corner tool head Label: 50 mm corner tool head APMT 0903 L40 mm with internal coolant Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.348 kg Cutting angle: 90° Cutting edges: 6 Special features Internal coolant Compatible with APMT 0903 indexable inserts Compatible insert manufacturer: Korloy Torx key: T8 Fastening screw: M2.5×5.5 ECLASS: 21181015 FAQ Which inserts fit this tool head? The head accepts APMT 0903 indexable inserts; inserts from Korloy are compatible and commonly used with this type of holder. Is coolant supply required for optimal performance? The built-in internal coolant significantly improves chip evacuation and tool life; operation without coolant is possible but may reduce insert life and affect surface finish. What fastening hardware is supplied for insert clamping? Clamping uses a Torx-driven screw system; the specified drive is Torx T8 with an M2.5×5.5 fastening screw for secure insert retention. Can this head be balanced for high-speed applications? The compact geometry and modest mass of 0.348 kg assist in minimising imbalance; balancing suitability depends on the complete tool assembly and machine spindle requirements. What cutting angle is provided and what does that mean for edge machining? The head has a 90° cutting angle, which is ideal where precise square shoulders or corner features are required and where a defined indexed insert orientation is beneficial. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust tool that combines 50 mm diameter accuracy with internal coolant for improved chip evacuation and longer insert life; the head accepts APMT 11T3 indexable inserts and features a 90° cutting angle for precise shoulder milling — order directly via Metav Werkzeuge or ask our consultants for tailored advice. 50 mm angle cutter head T252-1TM – internal coolant, for APMT 11T3 indexable inserts (Teknik Makina) The 50 mm angle cutter head T252-1TM is a compact cutting head designed for precision face and shoulder milling with APMT 11T3 indexable inserts, combining a short overall length with internal coolant to support consistent surface quality in series production 50 mm diameter for compact tool assemblies Internal coolant for improved chip control Accepts APMT 11T3 indexable inserts (Korloy) 90° cutting angle, length 40 mm Accurate machining for repeatable production results The cutter head is optimised to deliver consistent geometries in shoulder and face milling operations. With a 50 mm body and 90° cutting angle, the component provides stable cutting kinematics, while compatibility with APMT 11T3 inserts (Korloy) allows the selection of grades and geometries to match the workpiece material. The relatively short L40 mm overall length reduces overhang, lowering vibration and helping to achieve tighter tolerances in serial production runs. The robust design supports predictable tool life and repeatable set-up in workshop and industrial environments. Internal coolant and chip control enhance process reliability A routed coolant channel supplies lubricant and cooling directly to the cutting zone, which reduces thermal load at the cutting edge and improves surface finish. The presence of internal coolant assists with efficient chip control and chip evacuation, decreasing the risk of built-up edge and re-cutting. For mixed or interrupted cuts this mechanism contributes to longer insert service life and more stable cutting forces, which in turn supports higher average productive machining time and fewer unscheduled tool changes. Quick clamping and durable construction for workshop use Assembly and clamping are designed for fast, secure set-up: the head uses a T8 drive and M2.5x5.5 fastening screw for solid insert retention, while a 22 mm mounting bore matches common small-shank toolholders. The unit’s mass of 0.332 kg and the provision of six cutting edges on the chosen insert geometry ensure a balanced tool for repeated cycles. This combination of secure fastening, compact mass distribution and standardised fixing elements shortens changeover times and reduces the likelihood of insert seating errors in busy production workflows. For reliable precision machining with Teknik Makina’s angle cutter head, contact Metav Werkzeuge in Emmerich for immediate delivery options and application advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: T252-1TM Product: Angle cutter head Brand: Teknik Makina Label: 50 mm angle cutter head APMT 11T3 L40 mm with internal coolant ECLASS: 21181015 Facts Diameter: 50 mm Total length: 40 mm Mounting bore: 22 mm Weight: 0.332 kg Cutting angle: 90° Number of cutting edges: 6 Special features Internal coolant: yes For indexable inserts: APMT 11T3 Compatible insert manufacturer: Korloy Torx key: T8 Torx screw: M2.5x5.5 Manufacturer: Teknik Makina SKU: T252-1TM FAQ Which inserts fit this cutter head? The cutter head accepts APMT 11T3 indexable inserts; Korloy grades are suitable and commonly used with the T252-1TM for a range of finishing and light roughing applications. Is coolant supplied through the tool body? Yes, the T252-1TM features internal coolant which feeds the cutting zone to aid chip evacuation and reduce cutting temperatures. What machining tasks is the head best suited for? The head is intended for precise face and shoulder milling where a 90° cutting angle and compact 50 mm diameter support repeatable edge definition and consistent surface quality. How is an insert secured and what drive is required? Inserts are clamped with the supplied screw M2.5x5.5, tightened with a T8 Torx drive to ensure secure seating and consistent clamping torque. What are the mounting and balance characteristics? The tool mounts into a 22 mm bore and weighs 0.332 kg, offering a compact, well-balanced solution for short-reach milling operations with stable cutting behaviour. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust 50 mm corner turning head with internal coolant and compatibility with R390 17 indexable inserts ensures stable chip control and repeatable corner finishes. The compact design and 22 mm shank deliver straightforward integration into modular setups. Order the component directly via Metav Werkzeuge or consult our technical team for specification support. Corner turning head T404-1TM – 50 mm diameter, internal coolant (Teknik Makina) The Corner turning head T404-1TM is a compact indexable head for corner turning, engineered for coolant-through performance and reliable use with R390 17 inserts in demanding workshop applications 50 mm diameter for compact turning Internal coolant for improved chip evacuation Compatible with R390 17 Sandvik inserts 22 mm shank and 45 mm overall length Predictable results through coolant-through chip control The toolhead provides internal coolant directly to the cutting zone, which supports consistent chip evacuation and reduces built-up edge during interrupted cuts. With a true 90° cutting angle and support for R390 17 indexable inserts, the head secures repeatable corner geometry and surface quality. Engineers will value the combination of coolant routing and rigid seating, which together reduce rework and help maintain cycle-time stability in series production. Fast insert changes and system compatibility Designed for quick maintenance, the head uses a T15 Torx interface and M3.5x8.5 fixing screws for secure insert clamping and predictable torque values. The 22 mm connection diameter and 45 mm overall length enable straightforward integration into common modular toolholders, shortening setup time on the shop floor. At 0.591 kg the component is easy to handle while remaining robust enough for daily use, aiding efficient changeovers and minimising downtime. Built for reliable workshop performance and wide compatibility Manufactured by Teknik Makina, the T404-1TM indexable head pairs with Sandvik R390 17 inserts to cover a broad range of corner-turning tasks where stability and finish matter. The compact form factor and straightforward fixing system reduce spindle overhang, improving rigidity and tool life. Specified components and familiar interfaces simplify procurement and spare-parts planning, supporting predictable production runs and easier maintenance planning. For technical clarification or to reserve supply of the Teknik Makina corner turning head, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and order support. Technical data Article number: T404-1TM Product type: Corner turning head Brand: Teknik Makina Compatible inserts: R390 17 Compatible insert manufacturer: Sandvik Internal coolant: yes Torx key: T15 Torx screw: M3.5x8.5 Core dimensions Diameter: 50 mm Overall length: 45 mm Shank diameter: 22 mm Weight: 0.591 kg Cutting angle: 90° Cutting edges: 5 Features & compatibility Indexable head for corner turning ECLASS: 21181015 SKU: T404-1TM Label: 50mm Eckmesserkopf R390 17 L45mm mit Innenkühlung FAQ Which inserts fit this corner head? The T404-1TM corner turning head is designed for R390 17 indexable inserts and is compatible with Sandvik insert geometry. Is coolant-through available with this tool? Yes, coolant is routed through the head to the cutting zone; the internal coolant feature supports chip control and reduces edge build-up. What shank size and length should the holder accept? The head uses a 22 mm connection and has a 45 mm overall length, suitable for modular toolholder systems accepting that shank diameter. What fastening hardware is required for insert mounting? Insert clamping employs a Torx T15 interface with M3.5x8.5 fixing screws for secure mounting. Who manufactures this tool and how is it distributed? The component is manufactured by Teknik Makina and distributed via Metav Werkzeuge; SKU T404-1TM identifies the specific item. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precision, secure clamping and compact dimensions to streamline 90° turning operations; the holder’s compatibility with LNGU 15T6 inserts and simple Torx fastening reduce tool-change time and maintain process stability — order the component directly via Metav Werkzeuge or ask the consultants for application advice. Corner tool head – 90° tool head for LNGU 15T6 indexable inserts by Teknik Makina Corner tool head for 90° turning and finishing operations with LNGU 15T6 indexable inserts, designed for secure mounting and repeatable positioning in small to medium turning setups 90° cutting angle for precise corner turning Compatible with Kennametal LNGU 15T6 inserts 22 mm shank diameter for secure mounting Torx M4x11 screw, T15 key for quick clamping Faster, more reliable 90° turning for repeatable parts The Corner tool head delivers a compact solution for right‑angled turning tasks where repeatability matters. Its 90° cutting geometry ensures predictable engagement when machining shoulders or facing operations, reducing setup variation and scrap. By combining a dedicated insert format with a rigid holder design, cycle times can be optimised without sacrificing surface quality, which benefits both small-batch and series production where consistent results are required. Secure mounting and straightforward insert clamping A secure connection to the machine spindle begins with the 22 mm shank diameter, which provides stable support under load and minimises deflection. The head uses a Torx M4x11 fastening screw together with a T15 key for reliable clamp force, enabling quick insert changes while maintaining concentricity. Compatibility with Kennametal LNGU 15T6 indexable inserts simplifies inventory management and ensures access to established insert grades for different materials and cutting conditions. Compact design that supports accessibility and handling With a nominal head diameter of 50 mm and an overall length of 40 mm, the holder is designed to fit tight tool stations and to improve access in confined turning fixtures. The lightweight construction (approx. 0.305 kg) reduces inertial loads on the tool turret and makes manual handling easier during tool setup. The head provides five cutting edges, allowing for efficient use of the insert geometry and predictable wear cycles, which contributes to lower tooling cost per part over time. Practical applications and workshop suitability This tool head is tailored for workshop environments that require dependable corner turning, facing and light profiling where LNGU 15T6 inserts are preferred. Its straightforward interface with common insert types and standard Torx clamping fits the needs of maintenance departments, contract workshops and small production lines. For processes requiring repeatability and reduced setup complexity, the holder offers a pragmatic balance of rigidity, ease of service and compatibility with established insert ranges. For technical clarification, application advice or to request a tailored supply from Metav Werkzeuge — quoting SKU T956TM and Teknik Makina — contact the Metav team and benefit from their precision expertise and fast, reliable fulfilment Technical data Article number: T956TM Manufacturer: Teknik Makina Designation: Eckmesserkopf For: LNGU 15T6 indexable inserts Core technical data Shank diameter: 22 mm Head diameter: 50 mm Overall length: 40 mm Cutting angle: 90° Cutting edges: 5 Weight: 0.305 kg Special features Compatible insert manufacturer: Kennametal Torx screw: M4x11 Torx key: T15 ECLASS: 21181015 FAQ What insert type does the head accept? The holder accepts LNGU 15T6 indexable inserts; it is supplied to suit that insert geometry and is compatible with Kennametal grades. Which fastener is used to secure the insert? Insert retention is via a Torx M4x11 screw tightened with a T15 key to ensure firm and repeatable clamping. What are the key dimensions for machine setup? Relevant dimensions are a 22 mm shank diameter, 50 mm head diameter and 40 mm overall length; the technical drawing or the SKU T956TM specification should be checked against turret clearances. Is the head suitable for tight tool stations? Yes; the compact form factor and lightweight design make the head well suited to constrained tool positions and close‑quarter turning setups. How many cutting edges are provided by the insert arrangement? The configuration supports five effective cutting edges per insert cycle, enabling efficient index changes and predictable wear scheduling. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, high-precision 90° indexable-insert head that combines secure M4x10 Torx fixation, compatibility with Walter LNHU 1306 inserts and a compact 22 mm mounting for minimal set-up changes — order directly via Metav Werkzeuge or consult our specialists for application support. Corner tool head T580TM — 90° indexable-insert turning head by Teknik Makina, compatible with LNHU 1306 The Corner tool head T580TM is a compact 90° indexable-insert turning head designed for reliable external turning and facing operations with Walter LNHU 1306 inserts 90° cutting angle for right-angle turning Compatible with Walter LNHU 1306 inserts 22 mm mounting shank for compact holders Secure M4x10 fixation, Torx T15 key Precision turning where space is limited The 90° geometry delivers fast, repeatable shoulder turning and facing operations while avoiding multiple re‑setups. The combination of a 90° cutting angle and support for indexable inserts means toolpaths remain predictable and clamping forces are directed through the head, reducing vibration and improving surface finish. This leads to measurable cycle‑time savings on short, repetitive cuts and helps maintain consistent part tolerances across production batches. Confident clamping and straightforward insert changes A robust M4x10 fastening screw operated with Torx T15 ensures secure seat retention under heavy cuts and simplifies routine maintenance. The Torx drive reduces cam‑out and allows repeatable torque application, which protects the insert pocket and limits the need for rework. Quick indexability of the insert reduces machine downtime and supports efficient shift changes for continuous production. Compact design for versatile machine setups With a 50 mm head diameter and 40 mm overall length, the head occupies little envelope space while maintaining sufficient rigidity for stable cutting. The 22 mm mounting facilitates compatibility with compact toolposts and driven tool adaptors, enabling integration into small lathes and multi‑spindle machines. At 0.35 kg the component is light enough to aid balance and reduce spindle load when used in multiple stations. Durable construction and consistent performance Manufactured with high-quality metal processing, the head is built to resist wear and to deliver a long service life, supporting predictable tool replacement intervals. The unit accommodates five cutting edges, enabling multiple index positions before replacement and contributing to lower tooling costs per part. Together with proven insert standards from Walter, this configuration supports dependable production runs and reproducible results. Contact Metav Werkzeuge for tailored procurement advice and secure supply of the Teknik Makina Corner tool head T580TM with Walter LNHU 1306 compatibility Technical Data SKU: T580TM Brand: Teknik Makina Product: Corner tool head for LNHU 1306 indexable inserts Fixing screw: M4x10 Torx key: T15 Dimensions & Core Data Head diameter: 50 mm Overall length: 40 mm Mounting bore / shank: 22 mm Weight: 0.35 kg Cutting angle: 90° Features & Compatibility Compatible with Walter LNHU 1306 inserts Number of cutting edges: 5 High-quality metal processing Long service life FAQ What inserts fit this head? The T580TM corner tool head is compatible with Walter LNHU 1306 indexable inserts, providing standardised seating and repeatable clamping. Which mounting size is required for installation? The head requires a 22 mm mounting bore and is designed for compact holders; ensure the toolpost accepts a 22 mm shank before fitting the T580TM. What fastening hardware is used to secure the insert? Insert clamping uses an M4x10 screw with a Torx T15 drive; the Torx interface reduces cam‑out and enables consistent torque application. Is the head suitable for heavy roughing cuts? The robust fixation and compact geometry support stable turning; for sustained heavy roughing, verify machine spindle power and holder rigidity for the intended application with the T580TM. How many index positions are available before insert replacement? The design accommodates five cutting edges, allowing multiple index positions and extending time between replacements for efficient production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid turning solution that combines internal coolant and a 50 mm head diameter for stable, high-quality finishes; order the tool via Metav Werkzeuge or consult our specialists for application advice. Corner tool head — 50 mm with internal coolant for ADKT 1706 indexable inserts by Teknik Makina Corner tool head for short overhang turning and grooving operations using ADKT 1706 indexable inserts, designed for workshop efficiency and coolant-assisted machining. Internal coolant for stable cutting 50 mm head diameter for rigid setup Compatible with ADKT 1706 Korloy inserts 90° cutting angle for versatile geometries Increased rigidity for consistent surface finish The compact design with a 50 mm head diameter and overall length L40 mm reduces overhang and vibration, enabling a more consistent surface finish in short-reach turning tasks. The reduced mass and balanced geometry contribute to repeatable chip formation and lower tool deflection, which translates into fewer reworks and improved process reliability. This makes the tool head particularly suited to operations where dimensional stability under load is essential. Coolant routing that extends insert life and improves chip control Integrated internal coolant channels deliver cutting fluid directly to the cutting zone, improving lubrication and chip evacuation. Targeted coolant reduces thermal load on the insert, which helps to preserve edge integrity and extends time between index changes. For workshops seeking to lower tooling costs per component, the coolant-assisted performance provides a measurable improvement in tool life and cutting consistency. Fast, reliable insert clamping for efficient shop workflows Designed for the ADKT 1706 insert family, the head accepts standard Korloy inserts and secures them with a M4x10 Torx screw (Torx T15). This familiar fastening method simplifies insert changes and minimises downtime during production swaps. The configuration supports straightforward maintenance procedures and keeps the toolholder ready for quick reconditioning at the bench. Practical characteristics for everyday CNC turning With five cutting-edge contacts and a 90° cutting angle, the head accommodates a range of turning geometries while preserving a compact envelope. The lightweight construction (approx. 0.285 kg) lowers rotating mass and supports responsive machine dynamics during feed and acceleration changes. Together, these features deliver a balance of agility and control that benefits small-batch production and mixed-series workshop environments. For applications that require targeted coolant performance and a compact, robust turning solution, request the Teknik Makina Corner tool head T590TM through Metav Werkzeuge — our consultants in Emmerich will advise on suitability and integration into existing setups. Technical data Article number: T590TM Manufacturer: Teknik Makina Product type: Corner tool head eClass: 21181015 Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.285 kg Cutting angle: 90° Cutting-edge contacts: 5 Special features Internal coolant For ADKT 1706 indexable inserts Compatible insert manufacturer: Korloy Torx screw: M4x10 Torx key size: T15 FAQ Which inserts are compatible with this tool head? The Corner tool head accepts ADKT 1706 indexable inserts; the head is commonly paired with Korloy ADKT 1706 inserts for reliable clamping and performance. Does the tool head provide internal coolant? Yes — the head features internal coolant channels that deliver fluid directly to the cutting zone to improve insert life and chip evacuation. What fastening is required for insert changes? Insert clamping uses a M4x10 Torx screw with a T15 key, enabling quick and standardised insert replacement on the T590TM corner tool head. What cutting geometries are supported? The head offers a 90° cutting angle and five contact points, suitable for a variety of profiling and shoulder-turning tasks that benefit from a compact tool envelope. Is the tool head suitable for short overhang applications? Yes — with a 50 mm head diameter and L40 mm overall length, the design is optimised for rigid, short-reach turning where vibration control and stability matter. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

A robust solution for precise shoulder milling: the combination of a 50 mm head diameter, a 90° cutting angle and internal coolant delivers stable, repeatable cuts and extended insert life; order the corner milling head directly via Metav Werkzeuge or consult the technical advisors for integration advice. Corner milling head (Eckmesserkopf) — 50 mm, internal coolant, for ANKX 1205 indexable inserts by Teknik Makina A corner milling head designed for accurate shoulder and slot work in industrial turning and milling centres, compatible with ANKX 1205 indexable inserts for reliable chip control and production-grade rigidity 50 mm head diameter Internal coolant for controlled chip evacuation Compatible with ANKX 1205 indexable inserts Torx T15 screw M4x10 for secure clamping High-performance shoulder milling with consistent results Engineered to deliver stable shoulder cuts, this cutter head combines a 50 mm diameter with a 90° cutting angle and five cutting edges to ensure consistent engagement and reduced vibration. The relatively compact 45 mm overall length balances reach with rigidity, minimising deflection during interrupted cuts. The result is predictable dimensional accuracy and a surface finish that supports downstream processes, reducing rework and improving cycle-time reliability. Operators and production planners gain a measurable performance uplift in repeatability and tool life when replacing worn tooling with this configuration. Keeping tools cool and extending insert life The integrated internal coolant channel directly supplies coolant to the cutting zone, improving chip evacuation and thermal control at the insert interface. This targeted cooling reduces thermal load on the insert, which in turn slows wear mechanisms and helps maintain cutting-edge geometry for longer periods. Compatibility with ANKX 1205 inserts allows for a wide range of grade and geometry choices, so the assembly can be optimised for tougher materials or high-speed operations without sacrificing process stability. Less frequent insert changes and reduced scrap contribute to a leaner production footprint. Fast, secure clamping for efficient changeovers Clamping integrity is provided via a Torx T15 drive and an M4x10 screw, offering secure fixation with a conventional workshop toolset. The straightforward screw interface simplifies insert replacement and reduces downtime during scheduled maintenance or grade changes. Designed to accept inserts from ISCAR, the head supports commonly used tooling specifications, enabling quick tooling standardisation across machines. The secure clamping also minimises micro-movement at the cutting edge, which benefits dimensional control and repeatable cycle times in mass-production environments. Robust design for seamless workshop integration Manufactured by Teknik Makina, the head is dimensioned and weighted to suit industrial toolholders and rigourous machining schedules—the unit weight of 0.433 kg contributes to a balanced spindle load while the overall geometry supports stable chip flow. The combination of proven mechanical fixation, internal coolant capability and broad insert compatibility makes this component suitable for series production as well as smaller job-shop batches where reliability matters. The configuration reduces process risk and helps maintain throughput without complex retrofitting. For dependable shoulder milling with precise coolant delivery, contact Metav Werkzeuge to arrange supply or discuss specification matching for Teknik Makina corner milling head SKU T572-1TM — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: T572-1TM UID: T572-1TM eClass: 21181015 Label: 50mm Eckmesserkopf ANKX 1205 L45mm mit Innenkühlung Product type: Eckmesserkopf For indexable inserts: ANKX 1205 Compatible insert manufacturer: ISCAR Manufacturer: Teknik Makina Core dimensions Diameter: 50 mm Overall length: 45 mm Weight: 0.433 kg Cutting angle: 90° Number of cutting edges: 5 Torx screw: M4x10 Torx key: T15 Internal coolant: yes Special features Compatibility with ANKX 1205 indexable inserts Designed for shoulder and slot milling Secure Torx clamping system Manufacturer: Teknik Makina Category path: Zerspanen › Eckmesserkopf FAQ Which indexable inserts fit this head? This corner milling head is designed for ANKX 1205 indexable inserts and accepts inserts from ISCAR as specified for the Teknik Makina unit (SKU T572-1TM). Does the head provide internal coolant to the cutting edge? Yes, the tool features internal coolant, directed to the insert interface to improve chip evacuation and extend insert life on the Teknik Makina corner milling head. What clamping hardware is used for insert fixation? Insert fixation uses a Torx T15 drive with an M4x10 screw to secure the insert reliably on the machining head (SKU T572-1TM). Is the head suitable for heavy interrupted cuts? The combination of a 50 mm diameter, 90° cutting geometry and secure Torx clamping provides the rigidity required for many interrupted and shoulder milling applications with reproducible results. How does this head integrate with existing toolholders? With a compact 45 mm overall length and an industry-standard insert interface, the cutter head can be integrated into common holders and setups; the Teknik Makina design supports straightforward replacement of existing corner milling solutions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid design, internal coolant and broad insert compatibility for reliable shoulder milling and repeatable cycle times. Order the tool or consult Metav Werkzeuge for specification support and delivery coordination. Corner Milling Head T171-1TM — 50 mm diameter, internal coolant (Teknik Makina) A Corner Milling Head T171-1TM engineered for ANKX 1607 indexable inserts, providing stable 90° shoulder milling and efficient chip evacuation in CNC turning and milling setups. 50 mm diameter for stable cutting Internal coolant for improved chip evacuation Compatible with ANKX 1607 inserts T15 Torx clamping for secure fixation Consistent rigidity for repeatable surface quality The compact 50 mm diameter combined with a total length of 40 mm results in a stiff tool geometry that reduces vibration and deflection during shoulder and face milling. Improved stiffness directly translates to consistent surface finish and tighter dimensional repeatability on series parts, which reduces downstream rework. The unit mass of 0.307 kg supports quicker spindle acceleration and stabilises tool behaviour during interrupted cuts, making the holder suitable for mixed production batches where cycle reliability matters. Internal coolant that extends insert life and improves process stability Integrated internal coolant supplies cutting fluid directly at the cutting zone, which assists cooling and chip control in demanding operations. Direct coolant reduces cutting temperatures and aids chip breaking, lowering the thermal load on the insert and thereby extending tool life. For operators and process engineers, this means fewer tool changes per shift and more predictable tool-change intervals, supporting higher machine uptime and reduced tooling cost per part. Broad insert compatibility and economical tool management Designed specifically for ANKX 1607 indexable inserts, the head accepts inserts from established manufacturers XTC and Gesac, offering flexibility when sourcing consumables. Each insert provides multiple cutting edges, and with four effective cutting edges available the overall tooling cost per edge is minimised. The 90° cutting angle is optimised for shoulder operations and square-corner features, while the T15 Torx clamping interface ensures a repeatable and secure clamping force for every index and change. Easy integration into production workflows The tool head is supplied as SKU T171-1TM and is ready for direct mounting in common modular holders used in turning and milling spindles. Its compact form and internal coolant capability support both high-feed finishing passes and medium-depth semi-finishing strategies. Clear specification of the head’s key parameters—50 mm diameter, 40 mm overall length, four cutting edges and internal coolant—simplifies CAM programming and tooling lists, enabling faster process setup and effective replacement planning in the tool crib. Contact Metav Werkzeuge to discuss how the Teknik Cutting Tools corner milling head fits into the production setup, request compatibility checks or arrange priority delivery via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: T171-1TM Type: Corner milling head For inserts: ANKX 1607 Brand: Teknik Makina Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.307 kg Cutting edges: 4 Cutting angle: 90° Torx key: T15 Special features Internal coolant: yes Compatible insert manufacturers: XTC, Gesac Indexable insert system: ANKX 1607 FAQ Which insert type is required for this tool head? The corner milling head is designed for ANKX 1607 indexable inserts; inserts from XTC and Gesac are compatible with the T171-1TM. Does the tool head provide coolant supply to the cutting zone? Yes, the T171-1TM features internal coolant to improve cooling and chip evacuation at the cutting edge. What cutting tasks is the head best suited for? The head is optimised for 90° shoulder milling and face milling where a stiff 50 mm diameter tool improves surface finish and dimensional stability. How is the insert secured in the head? Clamping is effected via a T15 Torx interface, ensuring a secure and repeatable fixation for each insert index. Can the head be used for finishing and semi-finishing passes? The tool head’s geometry and coolant capability make it suitable for both medium-depth semi-finishing and finishing strategies, delivering stable results in mixed production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 50 mm diameter for process stability, internal coolant for improved tool life and direct compatibility with ANKX 1706 indexable inserts for rapid changeovers; order via Metav Werkzeuge or consult our advisors for specification support. Corner tool head for ANKX 1706 indexable inserts — 50 mm, internal coolant (Teknik Makina) Corner tool head designed for external turning operations with ANKX 1706 indexable inserts, offering internal coolant and a compact 45 mm overall length for stable, high-precision machining. 50 mm diameter for stable cutting Internal coolant for efficient chip evacuation Compatible with ANKX 1706 inserts (ISCAR) Four cutting edges, 90° cutting angle Enhanced process stability through rigid geometry The solid construction and 50 mm diameter provide a rigid clamping base that reduces vibration and improves surface finish during shoulder and facing operations. By combining a compact 45 mm overall length with a balanced mass (approx. 0.371 kg), the head minimises overhang while maintaining necessary clearance for common turning tasks. This rigidity translates into consistent tolerances and fewer re-cuts, supporting lean production and predictable cycle times. Effective coolant delivery for longer tool life Integrated internal coolant supplies cutting fluid directly to the insert zone, supporting better chip control and lower cutting temperatures. This targeted cooling reduces thermal wear on the insert and the tool seat, extending the life of both the head and ANKX 1706 tips. For production environments where downtime is costly, the improved heat management leads to longer intervals between indexings and tool changes, increasing overall equipment effectiveness. Fast insert changes and broad compatibility The head accepts ANKX 1706 indexable inserts and is specified to suit ISCAR systems, enabling compatibility with widely used insert portfolios. The fixing is executed with an M5x12 Torx screw and a T20 Torx drive for secure seating and straightforward replacement. This arrangement ensures repeatable positioning of the insert, reducing set-up time and simplifying inventory management when standardised inserts are used across multiple toolholders. Compact, reliable design for daily production demands Designed by Teknik Makina, the unit combines a compact footprint with four workable cutting edges and a 90° cutting angle to handle common shoulder and contouring operations efficiently. The robust screw retention and precise seat geometry keep the insert stable under load, supporting reproducible machining results and reducing the risk of chatter. For workshops aiming to balance flexibility with durability, this head delivers dependable performance over many cycles. Select the Teknik Makina T442-1TM corner tool head with internal coolant to improve cycle consistency and reduce indexings — contact Metav Werkzeuge for tailored technical advice and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: T442-1TM SKU: T442-1TM Product type: Eckmesserkopf Manufacturer: Teknik Makina Facts Diameter: 50 mm Overall length: 45 mm Weight: 0.371 kg Cutting edges: 4 Cutting angle: 90° Special features Internal coolant For ANKX 1706 indexable inserts Compatible insert manufacturer: ISCAR Torx screw: M5x12 Torx key: T20 Eclass: 21181015 FAQ What inserts fit this head? The head is configured for ANKX 1706 indexable inserts and is compatible with ISCAR-standard inserts specified for that geometry; the T442-1TM accepts the same insert type without modification. Does the tool support through‑tool coolant? Yes, the model features internal coolant, delivering fluid directly to the cutting zone to aid chip evacuation and thermal control. What fastener is used to secure the insert? Inserts are clamped with an M5x12 Torx screw using a T20 drive for secure seating and repeatable positioning. Which applications suit this tool head best? The unit is ideal for shoulder turning and finishing operations where a 90° cutting angle and robust support are required for consistent surface quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact 50 mm diameter design with internal coolant and compatibility for AP-- 1604 indexable inserts to maintain consistent cycle times and reliable surface finish; order the corner tool head directly via Metav Werkzeuge or consult our specialists if clarification is required. Corner tool head T183-1TM — 50 mm diameter, internal coolant (Teknik Makina) Corner tool head T183-1TM provides a compact cutting solution for turning operations using AP-- 1604 indexable inserts, optimised for controlled chip flow and short overhangs. 50 mm diameter for stable cutting Internal coolant for secure chip evacuation Compatible with AP-- 1604 indexable inserts Robust M4x10 Torx screw fixing Consistent rigidity for repeatable surface quality The compact construction of this tool head combines a 50 mm diameter body with a short overall length of 45 mm, delivering reduced overhang and improved stiffness during cutting. Lower deflection translates directly into more consistent part geometry and surface finish, which is especially relevant for serial production. The moderate mass of 0.401 kg keeps the assembly well balanced on standard tool posts while supporting stable feed rates. Coolant-through routing extends insert life A coolant-through design supplies cutting fluid directly to the cutting zone, reducing temperatures and facilitating chip control. This results in slower tool wear and fewer unplanned insert changes, improving uptime. For operations where coolant delivery matters—difficult-to-evacuate chips or higher cutting speeds—the internal routing supports longer service intervals and steadier process parameters. Secure clamping for quick indexable changes Mechanical retention relies on a proven M4x10 Torx screw with a T15 key interface, ensuring reliable clamp force and simple removal during insert changes. The 90° cutting angle provides a predictable cutting geometry that suits many finishing and profiling tasks. Five indexed cutting positions allow efficient rotation and balanced wear management without frequent tool swaps. Broad compatibility with AP-- 1604 insert systems Designed for AP-- 1604 indexable inserts and optimised for Korloy insert geometries, the head integrates smoothly into existing tooling families. Compatibility with widely used insert standards reduces setup complexity and inventory variety, enabling straightforward retrofitting in established turning cells or bench lathes. Practical workshop integration and handling The compact footprint and ergonomic fixing mean the head is quick to fit and set up; shorter overhangs shorten cycle times and simplify clamping checks. The labelled SKU T183-1TM supports easy reordering and stock management. The combination of compact design and internal coolant makes it a pragmatic choice for medium-duty turning where process stability and ease of maintenance matter. Manufacturer quality and operational reliability Produced by Teknik Makina, this tool head is engineered for consistent performance in industrial environments and routine machining tasks. The focus on robust fastenings, effective coolant delivery and standard insert compatibility helps maintain predictable operating costs and less downtime—key concerns for production planners and workshop managers. Contact Metav Werkzeuge to discuss integration of the Teknik Makina corner tool head T183-1TM into existing setups or to request detailed technical data for specific applications Technical data SKU: T183-1TM Label: 50mm Eckmesserkopf AP-- 1604 L45mm mit Innenkühlung Manufacturer: Teknik Makina Key specifications Diameter: 50 mm Overall length: 45 mm Weight: 0.401 kg Cutting angle: 90° Cutting edges: 5 Features and compatibility Internal coolant: Yes For inserts: AP-- 1604 Compatible insert brand: Korloy Torx screw: M4x10 Torx key: T15 FAQ What insert type does this tool head accept? This corner tool head accepts AP-- 1604 indexable inserts and is specified for insert geometries from Korloy. Is the coolant delivered to the cutting edge? Yes, the tool head features internal coolant routing that supplies fluid directly to the cutting zone to improve chip control and reduce insert wear. Which fastener and key are required for insert clamping? Clamping uses an M4x10 Torx screw and requires a T15 Torx key for reliable tightening and quick insert changes. Does the head suit heavy overhang applications? The compact 50 mm diameter and 45 mm overall length are optimised for minimal overhang; for very long reaches, a different tool geometry may be preferable. Can this head be used on manual lathes and CNC machines? The mechanical design and standard insert compatibility make it suitable for both manual lathes and CNC turning centres where AP-- 1604 inserts are used. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise 90° indexing, a compact Ø50 mm body and secure M2x4.2 Torx clamping for consistent, repeatable turning results; order directly via Metav Werkzeuge or consult our specialists for application advice. Corner tool head – 90° indexable insert holder by Teknik Makina, for APMT 0602-0903 The Corner tool head is a purpose-built 90° indexable insert holder designed for accurate external turning and profiling with APMT 0602 inserts, suitable for general workshop and light industrial turning applications. 90° indexable insert head APMT 0602 Compatible with Korloy KRLY inserts Compact Ø50 mm body and 22 mm bore Secured with M2x4.2 Torx screw T6 Precision turning at a defined 90° for consistent geometry The holder provides a fixed 90° orientation ideally suited to repeatable corner turning and profiling. With compatibility for APMT 0602 inserts and the KRLY designation, the component simplifies tool selection and setup. The design minimises play between insert and holder, which improves repeatability and reduces scrap. This results in a measurable benefit for batch production where consistent part geometry and surface finish are required, lowering rework and maximising machine uptime. Robust construction and secure clamping for stable cutting A compact body of Ø50 mm with a 22 mm bore (22 mm) gives a rigid connection to common tool posts and turrets, enhancing cutting stability. The insert is clamped with an M2x4.2 Torx screw and driven by a T6 torx key for straightforward, vibration-resistant fixation. Thanks to this secure fastening, the assembly delivers stable rake and clearance angles under moderate cutting forces, supporting longer insert life and predictable tool performance during interrupted cuts or shoulder machining. Efficiency in workshop workflows and easy integration The holder’s standardised interface for APMT 0602 inserts and compatibility with Korloy grades streamlines tooling logistics and reduces changeover time. The compact format helps conserve turret space and enables denser tool layouts for multi-op operations. Fewer tool changes and clear specification documentation support faster process qualification and make the component a practical choice for small series and maintenance workshops seeking reliable everyday performance without complex retooling. Contact Metav Werkzeuge for tailored procurement and reliable supply directly from Emmerich — call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: T597TM Brand: Teknik Makina ECLASS: 21181015 Designation: for 90° APMT 0602-0903 Indexable Inserts Insert type: KRLY Compatible insert manufacturer: Korloy Numbers / Core technical data Diameter: 50 mm Overall height: 40 mm Bore / shank diameter: 22 mm Cutting edges: 12 Torx screw: M2x4.2 Torx key size: T6 Special features / Versions 90° indexable insert orientation Designed for APMT 0602 inserts Compact body for dense turret layouts Secure Torx clamping for vibration resistance FAQ Is this holder compatible with Korloy APMT 0602 inserts? Yes. The Corner tool head from Teknik Makina (SKU T597TM) is specified for APMT 0602 inserts and accepts Korloy KRLY insert types. Which tool post or turret sizes suit the holder? The holder features a 22 mm bore and a Ø50 mm body; compatibility with common tool posts and turret adapters that accept a 22 mm mounting is expected for stable operation. How is the insert secured in the holder? Insertion is secured with an M2x4.2 Torx screw, tightened using a T6 key to ensure a vibration‑resistant clamp and consistent cutting geometry. What applications benefit most from this tool head? The assembly is optimised for 90° corner turning and profiling tasks where repeatable geometry and compact turret layout are priorities, making it suitable for small series and repair shop work. Can the holder be used across different insert grades? Yes. While physically compatible with APMT 0602 inserts, performance depends on the chosen insert grade; Teknik Makina holders work with a variety of Korloy grades for different materials and cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid turning solution that combines a 50 mm footprint with internal coolant for improved insert life and consistent surface finish; order the Teknik Makina angle tool head directly via Metav Werkzeuge or consult their application specialists for integration advice. Eckmesserkopf T697TM – 50 mm angle tool head with internal coolant by Teknik Makina The Eckmesserkopf for ADKT 10T3 indexable inserts is a compact 50 mm turning head designed for perpendicular 90° operations and confined machining envelopes. 50 mm diameter for compact turning operations Internal coolant for improved chip evacuation Compatible with ADKT 10T3 Korloy inserts 90° cutting angle for perpendicular cuts Engineered compactness for stable turning and access The compact construction with a 50 mm diameter and an overall length of 40 mm delivers a low-profile solution for restricted toolpaths without sacrificing rigidity. A defined 90° cutting angle makes perpendicular machining straightforward, while the low mass (0.23 kg) reduces rotating inertia and vibration. This combination yields improved process stability and repeatable results in short overhang and face-turning applications, supporting reliable component tolerances and consistent surface quality. Coolant-through routing to protect inserts and improve finishes The integrated internal coolant channel directs lubricant and coolant precisely to the cutting zone, reducing flank temperatures and assisting chip breakage. As a result, insert life is extended and abrasive wear is delayed, which reduces tool-change frequency and machining cost per part. The head is optimised for ADKT 10T3 indexable inserts and is compatible with common Korloy grades, simplifying procurement and ensuring matched carbide geometries for high-performance cutting cycles. Secure clamping and quick indexing for productive setups Fixing uses a Torx T8 drive with an M2.5x5.5 fastening screw to provide repeatable clamping and predictable torque transmission. The design offers six indexing positions for rapid rotation to fresh cutting edges, reducing downtime during batch production. Supplied as SKU T697TM by Teknik Makina, the tool head integrates with established turning toolholders and supports expedited tool replacement strategies that benefit lean machining processes. Contact Metav Werkzeuge for a tailored recommendation on integrating the Teknik Makina T697TM into existing turning fixtures and for precise ordering information Technical data SKU: T697TM Product type: Angle tool head Diameter: 50 mm Overall length: 40 mm Weight: 0.23 kg Brand: Teknik Makina Facts Shank bore: 16 mm Number of cutting positions: 6 Cutting angle: 90° Threaded screw: M2.5x5.5 Torx key: T8 ECLASS: 21181015 Special features Internal coolant (coolant-through) Compatible with ADKT 10T3 indexable inserts Suitable for Korloy insert grades Compact design for confined toolpaths Rapid indexing for reduced downtime FAQ What inserts does this tool head accept? The head accepts ADKT 10T3 indexable inserts and is specified for Korloy grades; the configuration is compatible with established ADKT geometries. Does the head provide through-coolant capability? Yes, the unit features internal coolant routing to the cutting zone to improve chip control and extend insert life. How is the insert fixed and indexed? Indexing is achieved with six positions; insert clamping uses a Torx drive (T8) and an M2.5x5.5 fastening screw for repeatable torque and secure seating. Is this suitable for tight overhang applications? The compact 50 mm diameter and 40 mm overall length make the head appropriate for confined turning operations where rigidity and access are required. Which SKU should be referenced when ordering? Order reference SKU T697TM for the Teknik Makina angle tool head configured for ADKT 10T3 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a 90° indexable insert holder with a 22 mm shank and a 50 mm head diameter delivers stable right‑angle turning and consistent repeatability for short‑run and batch work. Reliable M5x12 Torx fastening and compatibility with ANKX insert formats make the tool ideal for quick insert changes and predictable chip control. Order supply through Metav Werkzeuge or request technical advice from our consultants for seamless integration. Teknik Makina 90° Indexable Insert Holder (T442TM) — for ANKX 0706 indexable inserts, 22 mm shank Teknik Makina 90° indexable insert holder for right‑angle turning applications, designed to accept ANKX indexable inserts and to fit toolposts with a 22 mm bore 90° cutting geometry for right‑angle turning 22 mm shank diameter for secure mounting Compatible with ANKX 0706 indexable inserts Torx M5x12 fastening, T20 key required Built for dependable right‑angle turning The holder is engineered around a 90° cutting geometry, which converts axial tool movement into precise radial engagement for chamfers, shoulder turning and face work. The robust head with a 50 mm diameter supports controlled chip flow and stable cutting conditions, reducing vibration and improving surface finish. By keeping the cutting edge at a fixed right angle, setup time is shortened and cycle consistency is improved, which benefits production processes where repeatability and predictable tool life are essential. Precision interface and secure clamping for repeatable results A 22 mm shank ensures a tight fit in standard toolposts and quick‑change adapters; the component’s secure interface contributes directly to machining accuracy. The insert is retained using an M5x12 Torx screw (T20), providing reliable clamping torque and straightforward re‑indexing of the insert. The overall length of 45 mm and a compact mass of 0.371 kg keep tool overhang minimal, which lowers deflection and promotes dimensional stability during finishing passes. Compatibility that simplifies tooling logistics Compatibility with the ANKX 0706 insert family and the reference to ANKX insert formats allows easy sourcing of indexable carbide inserts from mainstream suppliers such as ISCAR. The head is configured for four cutting edges, enabling economical insert indexing and fewer interruptions for tool change. For customers unfamiliar with indexable systems: an indexable insert is a small, replaceable cutting plate; worn edges are rotated or replaced without regrinding the whole tool, which reduces tooling cost per component and speeds up maintenance routines. Workshop advantages and straightforward maintenance With a compact footprint and simple fastening, the holder supports efficient workshop workflows: faster changeover, reduced set‑up time and lower inventory complexity when paired with standard ANKX inserts. The Torx drive simplifies clamp torque control, improving repeatability across shifts. Routine maintenance is limited to inspection of the seat and screw torque; replacement of the Torx screw and straightforward cleaning prevent seizing. Together, these aspects help maintain productivity while supporting quality standards expected in small to medium‑sized production environments. Contact Metav Werkzeuge for tailored supply and technical advice on the Teknik Makina 90° indexable insert holder (T442TM), ensuring rapid delivery and professional guidance from Emmerich. Technical data SKU: T442TM Manufacturer: Teknik Makina Product: 90° indexable insert holder Head diameter: 50 mm Shank diameter: 22 mm Overall length: 45 mm Weight: 0.371 kg Compatible inserts: ANKX 0706 (indexable inserts) Also referenced insert: ANKX 1710 Compatible insert manufacturer: ISCAR Cutting angle: 90° Number of cutting edges: 4 Fastening: Torx screw M5x12, Torx key T20 FAQ Which insert formats fit this holder? The holder is designed for ANKX 0706 indexable inserts and references ANKX insert formats; compatibility with ANKX sizes simplifies sourcing of replacement inserts from suppliers such as ISCAR. What is the shank diameter and what does it mean for mounting? The 22 mm shank diameter is specified for secure mounting in compatible toolposts or adapter blocks; it ensures low run‑out and consistent clamping for precision turning operations. How is the insert secured and maintained? Insert retention uses an M5x12 Torx screw with a T20 key; correct torque and occasional inspection of the seat are the main maintenance tasks to preserve repeatability. What typical operations is this holder suited for? Configured for right‑angle and shoulder turning, the holder is well suited to chamfering, face turning and small profile work where a 90° geometry provides the desired cutting engagement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com