Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact, robust clamping solution that combines precise insert positioning and space-saving dimensions for reliable external turning operations; order directly via Metav Werkzeuge or request tailored advice from the consultants. Clamping holder SDJC for DCMT indexable inserts — right-hand, flat style by Teknik Makina The SDJC for DCMT Indexable Inserts is a right-hand clamping holder designed for external turning with a flat head, optimised for DCMT 11T3 inserts in confined setups. Right-hand clamping holder SDJCR 1212 Flat head for DCMT 11T3 indexable inserts 12 × 12 mm head dimensions for compact turning 110 mm overall length, lightweight 0.134 kg Stable cutting performance for small-diameter turning The holder, designated SDJCR 1212, secures DCMT 11T3 indexable inserts in a low-profile mounting that reduces tool overhang and vibration. The flat head geometry, together with a defined 93° cutting angle, was engineered to maintain a repeatable cutting edge position, which is beneficial when machining short, external profiles. Precision is supported by the standardised ISO-style seat, so insert seating and indexing are consistent; this reduces set-up deviations and contributes to predictable tool life and part tolerances. Space-saving design that improves machining access With a head footprint of 12 mm by 12 mm and an overall length of 110 mm, the turning holder enables access in tight fixtures and close to shoulders where larger tools would obstruct the operation. The holder’s lightweight construction (0.134 kg) reduces dynamic loads on the turret during rapid direction changes, which helps to preserve surface finish. The right-hand orientation is matched to clockwise cutting applications and is suitable for many general-purpose turning tasks in job shops and production cells where compactness and rigidity are required. Compatibility and practical workshop advantages The unit accepts indexable inserts, permitting economical regrinds and rapid replacement without full tool change. The bar designation J11-F indicates the compatible shank system for insertion into common tool posts and turrets. As a standardised clamping solution, the component is compatible with established insert grades and chipbreaker geometries, allowing adaptation to a wide range of materials and cutting conditions while keeping inventory management straightforward. Reliability, supply and partner assurance Manufactured by Teknik Makina and distributed through Metav’s quality-controlled supply chain, the toolholder combines practical design with consistent availability for workshop planners. The standardised ISO-style identification and compact dimensions mean predictable integration into existing tooling setups, reducing planning time and improving machine uptime. For machining strategies where small turnings, close tolerances and repeatable insert location matter, this holder delivers measurable process stability. Contact Metav Werkzeuge for specification matching and delivery from Emmerich — telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for tailored advice and rapid dispatch. Technical Data Article number: D457TM Manufacturer: Teknik Makina Product: SDJC for DCMT Indexable Inserts SKU: D457TM ISO designation: SDJCR 1212 Compatible insert: DCMT 11T3 Cut direction: right eClass: 21181004 Facts Head width: 12 mm Head height: 12 mm Head cutting width: 12 mm Overall length: 110 mm Weight: 0.134 kg Cutting angle: 93° Special features Flat head design Right-hand clamping holder Bar designation J11-F Indexable insert compatibility Compact, low-profile construction FAQ What inserts fit this clamping holder? The clamping holder is specified for DCMT 11T3 indexable inserts and secures them via the SDJCR 1212 seat for standard seating and indexing. Is the holder right- or left-hand oriented? This toolholder is a right-hand design, intended for clockwise cutting directions in standard turning operations. What are the key dimensions to check for turret fitment? Critical dimensions are the 12 mm head width/height and 110 mm overall length; verify turret clearance and the J11-F bar designation for correct shank compatibility. Will the holder work in tight shoulder machining? Yes — the flat head and compact 12 × 12 mm footprint are intended to improve access in confined setups while maintaining a stable cutting position. Which manufacturer produces this toolholder and who supplies it? The toolholder is produced by Teknik Makina and supplied via Metav’s distribution, referenced under SKU D457TM for procurement and stock enquiries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, left‑hand clamping solution with internal coolant and proven compatibility with DCMT 11T3 indexable inserts for steady turning performance; purchase directly from Metav Werkzeuge or request specialist advice from our consultants. SDJC Clamping Holder for DCMT Indexable Inserts — Left‑hand holder with internal coolant (Teknik Makina) The SDJC for DCMT Indexable Inserts is a left‑hand clamping holder designed for turning operations that require internal coolant delivery and a compact 12 mm shank for versatile workshop use Holder SDJCL 1212 by Teknik Makina Internal coolant for reliable chip evacuation Compatible with DCMT 11T3 indexable inserts Left‑hand orientation, 93° cutting angle Precision clamping for reproducible turning results The holder is engineered to deliver consistent clamping pressure via its SDJCL 1212 ISO profile, which secures DCMT‑style inserts with repeatable seating. This reduces setup time and minimises rework by keeping the insert position stable across cycles. The compact 12 mm shank and 16 mm cutting head width balance rigidity and access, so turning tasks that demand tight tolerances benefit from reduced vibration and improved surface finish. Coolant‑assisted chip control that supports productivity Equipped with internal coolant, the tool directs coolant to the cutting zone so chips are cleared efficiently and tool life is extended. For materials that produce long or stringy chips, forced coolant can prevent martensitic heat build‑up and lessen manual cleaning intervals. The internal feed is integrated without compromising the holder profile, meaning coolant is supplied while retaining full clamping reliability. Designed for workshop compatibility and quick changeovers Compatibility with DCMT 11T3 indexable inserts and the J11‑IC toolholder designation ensures that the holder fits common insert geometries and available insert grades. The left‑hand orientation and 93° cutting angle are suited to specific turning set‑ups, while the supplied Torx and clamping hardware (M3.5x11 Torx screw, T15 key, and M5 clamping plate screw) are industry standard for rapid, secure insert changes. At 110 mm overall length and 0.11 kg weight, the holder is easy to handle during tool changes and storage. Built for reliable, everyday workshop use Materials and construction are focused on longevity and consistent performance; the holder is finished to withstand routine use and is compatible with a range of insert grades for diverse materials. The robust clamping mechanism, together with measured dimensions and a 32 mm cutting height, supports repeatable setups and predictable machining results, so production planners can schedule operations with confidence rather than frequent adjustments. For reliable turning with internal coolant and DCMT compatibility, contact Metav Werkzeuge for availability and technical guidance — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP514TM Manufacturer: Teknik Makina ISO designation: SDJCL 1212 For indexable inserts: DCMT 11T3 Toolholder designation: J11-IC Weight: 0.11 kg Overall length: 110 mm Total height: 12 mm Shank width: 12 mm Cutting head width: 16 mm Cutting height: 32 mm Cutting angle: 93° Internal coolant: yes Cutting direction: left U‑plate: TA030 U‑plate screw: M5 Torx screw: M3,5x11 Torx key: T15 SKU: AP514TM FAQ What insert types are compatible with this holder? The holder accepts DCMT 11T3 indexable inserts; the SDJC geometry is matched to that insert form for reliable seating and repeatability. Is the coolant internal or external on this clamping holder? Internal coolant is provided; coolant is channelled to the cutting zone to aid chip evacuation and tool life. What is the ISO designation and main dimensions of the holder? The ISO designation is SDJCL 1212, with a 12 mm shank width, 110 mm overall length and a 16 mm cutting head width. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact 12 x 12 mm shank, internal coolant, and compatibility with DCMT 0702 inserts to improve chip control and repeatability in small to medium turning operations. Order the tool via Metav Werkzeuge or contact the technical team for application advice. SDJCR 1212 clamp holder — right‑hand turning holder with internal coolant (Teknik Makina) The SDJCR 1212 clamp holder is a right‑hand turning toolholder designed for indexable DCMT 0702 inserts, offering internal coolant and a compact 12 x 12 mm shank for stable turning in confined setups. Right‑hand turning holder SDJCR 1212 Internal coolant for improved chip control Compatible with DCMT 0702 indexable inserts Compact 12 x 12 mm shank for small setups Improved cycle time through secure clamping and coolant supply The SDJCR 1212 is built for consistent production cycles by combining a robust clamping system with integrated coolant supply. The internal coolant channel directs cutting fluid close to the cutting edge, which reduces thermal load and improves chip evacuation; this leads to longer insert life and fewer interruptions for tool changes. With a lightweight construction of 0.17 kg and a 125 mm overall length, the holder balances rigidity and manoeuvrability, making it suitable for batch production and shorter set‑ups where fast throughput and reliable repeatability matter. Precision and compatibility for predictable turning results Configured for DCMT 0702 indexable inserts, the holder ensures consistent geometry and repeatable cutting conditions. The 93° cutting angle and 27 mm cutting height are engineered to maintain clearance and minimise interference in typical lathe operations. The part’s 12 x 12 mm shank and 16 mm cutting head width support accurate positioning in small turrets and tool posts, while the supplied M2.5×5.5 Torx screw (driven with a T8 key) secures the insert reliably, reducing micro‑movement under load. These features translate into stable surface finishes and predictable tool life in turning tasks. Practical workshop advantages and maintenance ease Assembly and maintenance are straightforward: the standard Torx fixation simplifies insert changes and ensures repeatable clamping torque, while the compact geometry reduces the need for special adapters. The holder’s compatibility with the common K07‑IC boring bar designation expands its integration options in modular setups. Because the design focuses on core performance—secure clamping, coolant delivery and dimensional compatibility—it supports both experienced setups and users seeking dependable results with minimal tuning. For dependable turning performance, request the Teknik Cutting Tools SDJCR 1212 clamp holder via Metav Werkzeuge or call +49 2822 7131930 / email info@metav-werkzeuge.com for tailored application advice Technical Data Article number: AP560TM Manufacturer: Teknik Makina ISO designation: SDJCR 1212 ECLASS: 21181004 Facts Shank width: 12 mm Shank height: 12 mm Cutting head width: 16 mm Cutting height: 27 mm Overall length: 125 mm Weight: 0.17 kg Cutting angle: 93° Special features Internal coolant Compatible with DCMT 0702 inserts Right‑hand cutting direction Torx screw: M2.5×5.5 Torx key: T8 Boring bar designation: K07‑IC FAQ Which inserts fit this holder? The holder is designed for DCMT 0702 indexable inserts, providing correct seating and repeatable geometry for standard turning tasks. Does the holder support internal coolant? Yes, this SDJCR 1212 clamp holder features internal coolant to direct fluid to the cutting zone and assist chip control. Is the clamping screw a standard size? The clamp is secured with an M2.5×5.5 Torx screw, tightened using a T8 key, ensuring straightforward insert changes and secure fixation. What is the intended cutting direction? The toolholder is configured for right‑hand turning operations and is optimised for that feed orientation. Can the holder be used in compact turrets? With a 12 x 12 mm shank and 125 mm overall length, the holder is suitable for compact turrets and limited‑space tool posts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise clamping, compatibility with 16 IR indexable inserts and a compact 110 mm form for reliable left-hand turning operations; order the clamping holder directly via Metav Werkzeuge or consult our technical advisors for application support. SEL 1212 Clamping Holder D508TM — left-hand turning holder for 16 IR inserts (Teknik Makina) SEL 1212 Clamping Holder D508TM is a left-hand turning toolholder designed for secure clamping of 16 IR indexable inserts in compact machining setups. SEL 1212 ISO turning toolholder For 16 IR indexable inserts Left-hand cutting orientation Compact 110 mm overall length Stable clamping for precise turning results The SEL 1212 design focuses on secure clamping to reduce vibration and maintain repeatable cutting geometry. With a compact clamping head and a robust fixing method, the holder gives consistent tool position, which translates into improved surface finish and longer insert life. The holder’s left-hand configuration suits turning operations that require negative lead or specific approach angles, and its secure clamping prevents micro-movements that can compromise dimensional accuracy during medium-duty turning. Faster set-up through standardised insert compatibility Compatibility with 16 IR indexable inserts and the specified shank designation simplifies tooling logistics and changeovers. The adapter fits common insert geometries, so tool changes and insert indexing take less time, reducing machine downtime. For workshops seeking a predictable production flow, the standard ISO-style sizing and the clear designation (SEL 1212) make integration with existing toolholders straightforward, supporting efficient process planning and lower overall tooling costs. Compact dimensions for accessibility and rigidity A reduced overall length and modest mass deliver both accessibility in tight setups and a favourable stiffness-to-reach ratio. The holder’s overall length of 110 mm, cutting head width of 16 mm and a cutting height of 22 mm are balanced to keep the tool close to the workpiece while maintaining rigidity. The low weight of 0.119 kg helps reduce centrifugal forces on rotating assemblies and improves dynamic stability during higher spindle speeds, supporting smoother cuts and reduced chatter on small to medium components. Practical partner for everyday workshop use Supplied in a standard ISO SEL 1212 form, this clamping holder is intended for straightforward integration into production or jobbing environments. The clear mechanical specifications make planning tooling inventories easier and help maintain process consistency across batches. As part of a trusted supply chain, Metav Werkzeuge supports dependable delivery and product selection, backed by decades of experience in precision tooling and an extensive product range to reduce procurement complexity. For tailored advice on applying the SEL 1212 clamping holder (D508TM) in specific turning tasks, contact Metav Werkzeuge for expert guidance and reliable supply from Emmerich at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: D508TM Brand: Teknik Makina ISO designation: SEL 1212 Compatible inserts: 16 IR Shank/bar designation: J16- IR16 Dimensions & weight Overall length: 110 mm Weight: 0.119 kg Cutting head width: 16 mm Holder height: 12 mm Holder width: 12 mm Cutting height: 22 mm Features Left-hand cutting orientation For indexable inserts 16 IR SEL 1212 clamping system Suitable for standard turning operations FAQ Which insert size fits this holder best? The SEL 1212 clamping holder (D508TM) is designed for 16 IR indexable inserts, ensuring standardised fit and simple insert replacement. Is the holder suitable for right-hand turning? This variant is configured for left-hand cutting direction; for right-hand operations, a corresponding right-hand holder should be chosen. What are the key dimensions to check for fixture clearance? Check the overall length of 110 mm, cutting head width 16 mm and cutting height 22 mm to confirm access and clearance in the intended set-up. Can the D508TM be used in short-reach, high-rigidity applications? Yes, the compact form and modest mass (0.119 kg) make the D508TM suitable where tool accessibility and stiffness are both needed. What shank or bar designation is compatible with this holder? The holder references the designation J16- IR16, which aligns with standard shank formats for this insert size. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact 12 mm shank and integrated internal coolant that improve chip evacuation and extend insert life; compatibility with APKT 1003 indexable inserts reduces set-up complexity. Order the cutter directly via Metav Werkzeuge or consult the technical advisors for application-specific recommendations. Milling cutter for APKT 1003 indexable inserts — 12 mm shank, internal coolant (Teknik Makina) A milling cutter engineered for APKT 1003 indexable inserts, intended for shank-mounted milling where internal coolant supports consistent machining and reliable tool life. 12 mm shank diameter Internal coolant through body Compatible with Korloy APKT 1003 inserts Overall length 100 mm Greater stability with a compact, rigid shank The compact 12 mm shank and an overall length of 100 mm combine to give a favourable stiffness-to-reach ratio for short-reach milling tasks. The relatively short 27 mm cutting length reduces deflection during engagement, which leads to more consistent cutting forces and improved surface finish. For operations where set-up time and tool change frequency are critical, the single-insert design simplifies inventory and reduces downtime while maintaining a stable cutting interface. Improved heat management and chip control for longer insert life With internal coolant routed to the cutting zone, the tool actively cools the insert seat and the cutting edge, aiding chip evacuation and reducing thermal load on the insert. This cooling strategy typically results in prolonged insert life and more predictable wear patterns, which supports process reliability in both batch and continuous production. The coolant path also helps to flush chips away from the tool body, lowering the risk of chip re-cutting and associated surface damage. Secure, fast clamping for repeatable set-ups Fast and repeatable insert changes are facilitated by the standardised fastening hardware: a T8 Torx drive and an M2.5×5.5 Torx screw ensure secure clamping with minimal play. The consistent clamping interface reduces the likelihood of insert movement under load, preserving the programmed tool offset and decreasing the need for repeated alignment. Compatibility with Korloy APKT 1003 inserts and the clear mechanical fastening method streamline workshop procedures and shorten machine downtime. Practical advantages for the production floor Lightweight at approximately 0.097 kg, the cutter body supports quick handling and reduces inertia on the turret or spindle attachment, which can be advantageous during multi-tool stations or frequent tool changes. The combination of a compact shank, integrated coolant and standardised screws makes this cutter suitable for precision milling tasks where controlled chip flow and easy maintenance are priorities. The model is supplied as a prepared tool body ready for APKT 1003 inserts and marked under SKU S136-1TM for straightforward reordering. Contact Metav Werkzeuge to specify the Teknik Makina milling cutter with internal coolant and to discuss application-matched insert grades and clamping options Technical data SKU: S136-1TM Product: Milling cutter (shank-mounted) Label: 12 mm shank cutter APKT 1003 L100 mm with internal coolant Manufacturer: Teknik Makina Core specifications Diameter: 12 mm Shank diameter: 12 mm Overall length: 100 mm Cutting length: 27 mm Cutting edges: 1 Weight: 0.097 kg Special features Internal coolant For APKT 1003 indexable inserts Compatible with Korloy inserts Torx key: T8 Torx screw: M2.5×5.5 Product type: Milling cutter (shank-mounted) FAQ Which inserts fit this cutter? The cutter is designed for APKT 1003 indexable inserts; compatibility with Korloy APKT 1003 inserts is explicitly supported for this Teknik Makina tool. Is coolant supply available through the tool body? Yes, the model features internal coolant to the cutting zone, improving chip evacuation and thermal control for the insert. What are the key dimensions for set-up planning? Key dimensions are a 12 mm diameter and shank, 100 mm overall length and 27 mm cutting length; the tool is listed as SKU S136-1TM for reference. How is the insert secured to the cutter? The insert is fastened with a T8 Torx screw (M2.5×5.5), providing a secure and repeatable clamping interface for reliable tool offsets. Is this cutter suitable for frequent tool changes on multi-tool turrets? The compact design, light weight (approx. 0.097 kg) and standardised fastening make it well suited to workflows with frequent tool changes where quick handling and repeatable clamping are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a modular, indexable system that combines cost-effective insert replacement with a secure Torx clamping for predictable tool life and minimal downtime; benefit from a compact 12 mm cutting diameter and a robust 16 mm shank for stable machining — order the S224TM directly via Metav Werkzeuge or ask our consultants for application support. Shank milling cutter S224TM – 12 mm diameter, APMT 11T3 insert interface (Teknik Makina) The S224TM is a shank milling cutter configured for APMT 11T3 indexable inserts, intended for precision milling tasks where rapid insert changes and consistent repeatability are required. 12 mm cutting diameter APMT 11T3 indexable insert interface 16 mm shank for standard holders Torx clamp M2.5x5.5, T8 key required Reliable modularity for lower tooling costs and quicker changeovers The body accepts APMT 11T3 indexable inserts, enabling a modular approach that reduces overall tooling expenditure and shortens machine downtime. By replacing only the worn insert rather than the whole cutter, maintenance cycles are simplified and inventory can be optimised. The combination of a 12 mm cutting diameter with a 25 mm cutting length provides a compact working envelope while maintaining cutting capacity for common profiling and slotting tasks. This modular design is particularly advantageous in small-batch production and toolrooms where changeover speed matters. Secure clamping and stable shank for accurate machining A secure Torx clamping screw ( M2.5x5.5 ) fastened with a T8 key ensures the insert remains seated under radial and axial loads, contributing to consistent surface quality and repeatable results. The 16 mm shank gives a rigid connection to standard toolholders, lowering the risk of run-out and vibration during milling. With a single cutting edge and a 90° cutting angle, the cutter body is configured for predictable chip formation and straightforward process planning. The low mass (approx. 0.126 kg) facilitates fast tool changes and reduces centrifugal effects at higher spindle speeds. Compatibility, maintenance and partner support for reliable production The cutter is compatible with inserts from Korloy in the APMT 11T3 format, allowing access to a broad range of grades and chipbreaker geometries without changing the tool body. Replacement and tightening follow a simple routine — loosen the Torx screw with a T8 key, replace the insert and retighten to the specified torque — reducing planned maintenance time. For customers seeking guidance on insert grades or machining parameters, Metav Werkzeuge brings decades of metrology and tooling experience, a wide product range and a reliable supply chain from Emmerich to the workshop. Trust and traceability are supported by a central stock and quality filter for the European market. For tailored technical advice or to request availability of the Teknik Cutting Tools S224TM shank milling cutter via Metav Werkzeuge, please contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S224TM Product name: Shank milling cutter S224TM Manufacturer: Teknik Makina Facts Cutting diameter: 12 mm Shank diameter: 16 mm Cutting length: 25 mm Overall length: 85 mm Weight: 0.126 kg Number of cutting edges: 1 Cutting angle: 90° Torx screw: M2.5x5.5 Torx key: T8 Special features Interface for APMT 11T3 indexable inserts Compatible insert manufacturer: Korloy Modular insert system for reduced tooling costs Single-edge configuration for predictable chip control Lightweight body for fast changeovers FAQ Which insert type fits this cutter? The cutter accepts APMT 11T3 indexable inserts; the body is designed specifically for that insert format to ensure correct seating and reliable performance. Is the clamping screw specification standard? Yes, the clamping uses a Torx M2.5x5.5 screw tightened with a T8 key, providing a secure and widely supported fastening method. What shank holders are suitable for this tool? The 16 mm shank is compatible with standard toolholders that accept a 16 mm shank diameter, offering stable mounting for typical milling applications. Can Korloy inserts be used with this cutter? Korloy inserts in the APMT 11T3 format are listed as compatible and are commonly used with this cutter body for a range of materials and coatings. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, rigid milling solution that combines a 12 mm shank and a 45 mm cutting length for stable, repeatable cuts; the compatibility with RDMW 0501 indexable inserts reduces tooling costs and simplifies maintenance. Order the tool directly via Metav Werkzeuge or consult the team for application support. Shank cutter — 12 mm cutter for RDMW 0501 indexable inserts (Teknik Makina) Shank cutter for light-duty milling operations, designed to accept RDMW 0501 indexable inserts and deliver reliable, easy-to-service performance in CNC and workshop environments. 12 mm shank diameter Compatible with RDMW 0501 inserts Two cutting edges for stable milling Total length 120 mm, lightweight 0.118 kg Greater stiffness and consistent cutting performance The compact design centres on a 12 mm shank, providing improved stiffness compared with longer or slimmer alternatives; this reduces vibration and supports repeatable geometries in interrupted or continuous cuts. With two cutting edges, the load per edge is reduced, helping to maintain a consistent surface finish while extending the interval between index changes. The 45 mm cutting length gives sufficient reach for pocketing and face-milling tasks without sacrificing rigidity, and the 120 mm overall length balances accessibility and stability for many common milling set-ups. Fast insert changes and secure clamping reduce downtime This indexable insert cutter accepts RDMW 0501 inserts and is specified for use with Taegutec-style plates, enabling rapid replacement of cutting edges instead of full-tool regrinds. The clamping system is secured with a Torx M2x4.2 screw and a T6 key, which ensures a reliable seat for the insert and repeatable positioning after each change. Using indexable inserts lowers running costs and simplifies inventory management, since worn edges are replaced quickly and accurately without special tooling. Workshop advantages: ease of handling and low spindle load Weighing just 0.118 kg, this cutter imposes minimal additional load on the spindle while remaining well balanced for stable rotation at typical machining speeds. The compact mass and straightforward geometry make it suitable for serial production and jobbing shops that value quick set-up and predictable tool life. The combination of a short, rigid shank and precise insert seating delivers predictable chip formation and supports efficient material removal rates where an indexable insert solution is the preferred choice. Contact Metav Werkzeuge for technical advice, stock availability or to reserve SKU R088TM — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: R088TM Brand: Teknik Makina For indexable inserts: RDMW 0501 Compatible insert maker: Taegutec Numbers / Core technical data Shank diameter: 12 mm Cutting length: 45 mm Overall length: 120 mm Cutting edges: 2 Weight: 0.118 kg Diameter: 12 mm Special features / Design details Torx screw: M2x4,2 Torx key: T6 Type: Shank cutter for indexable inserts SKU for ordering: R088TM Brand designation: Teknik Makina FAQ What insert type does this cutter accept? The cutter is designed for RDMW 0501 indexable inserts and is specified for use with Taegutec-compatible plates. Which Torx screw and key are required for insert clamping? Insert clamping uses a Torx M2x4.2 screw and a T6 key for secure seating. What are the main dimensions to consider for setup? Key dimensions include a 12 mm shank diameter, 45 mm cutting length, and 120 mm overall length (SKU R088TM). Is this tool suitable for high-speed machining? The tool’s compact shank and two cutting edges favour stability and predictable performance; suitability for high-speed applications should be validated against machine and insert specifications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise shank sizing, proven indexable-insert compatibility and easy serviceability for uninterrupted milling operations; order directly via Metav Werkzeuge or consult our specialists for technical advice. Shank cutter R086TM — indexable-insert mill for RDMW 0501, 12 mm shank, 2 cutting edges (Teknik Makina) The Shank cutter R086TM is an indexable-insert milling tool intended for light to medium milling tasks where compact tooling and fast insert changes are required 12 mm shank diameter for compact setups 40 mm effective cutting length Compatible with RDMW 0501 indexable inserts Includes M2x4.2 Torx screw, T6 key Stable cutting and precise fit that keeps cycles consistent The R086TM combines a 12 mm shank with a carefully matched body geometry to deliver stable engagement in confined tool holders. Compatibility with RDMW 0501 indexable inserts and common Taegutec grades ensures straightforward insert selection and predictable tool life. The secure clamping via Torx M2x4.2 screw (T6) reduces micro‑movement during milling, which in turn supports repeatable tolerances and reduces scrap rates. Efficient material removal with a compact, low‑vibration design Equipped with 2 cutting edges and a 40 mm cutting length, this insert mill balances metal removal rate and surface quality for many workshop applications. The overall length of 100 mm and a mass of 0.099 kg minimise centrifugal load and tool overhang, helping to reduce chatter and improve cycle times on smaller machines. The indexable concept lowers running costs because inserts can be rotated or replaced without scrapping the entire cutter body. Easy maintenance and integration into existing toolsets Service tasks are simplified: the indexable inserts are a standard RDMW 0501 format and the fastening hardware is a widely available Torx T6. This means replacement and maintenance can be completed quickly at the bench, keeping machine downtime to a minimum. The cutter body is supplied ready for use with recommended inserts and is suitable for retrofitting into existing setups that accept a 12 mm shank and the RDMW insert family. For reliable, workshop‑ready milling with Teknik Cutting Tools’ shank cutter R086TM, contact Metav Werkzeuge in Emmerich for tailored advice and fast order processing: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: R086TM Brand: Teknik Makina For inserts: for RDMW 0501 Indexable Inserts Compatible insert manufacturer: Taegutec Numerical data Shank diameter: 12 mm Cutting diameter: 12 mm Cutting length: 40 mm Overall length: 100 mm Number of cutting edges: 2 Weight: 0.099 kg Special features Torx screw: M2x4.2 Torx key size: T6 Indexable insert type: RDMW 0501 SKU: R086TM FAQ Which inserts fit this cutter? The R086TM is designed specifically for RDMW 0501 indexable inserts; insert grades from Taegutec are compatible. What are the key dimensions to check for machine compatibility? Check for a 12 mm shank holder and sufficient clearance for a 100 mm overall length when fitting the R086TM. How many cutting edges does the tool have and what is the cutting length? The tool has 2 cutting edges with an effective cutting length of 40 mm, optimised for balanced material removal. What fastening hardware is used for the inserts? Inserts are secured with an M2x4.2 Torx screw; the supplied or recommended driver is T6. Is the cutter suitable for high‑overhang operations? The R086TM is intended for compact set-ups; longer overhangs will affect stiffness and should be avoided for best results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact SIR S10H system that combines a Ø12 mm body with a shank Ø10 mm for stable internal turning and straightforward insert changes; benefit from the precise cutting height 20 mm and right-hand cutting geometry for predictable chip control — order directly via Metav Werkzeuge or consult the specialists for compatibility and supply. Boring Bar K337-3TM (SIR S10H) by Teknik Makina — for 11 IR indexable inserts, Ø12 mm, 100 mm length Boring Bar K337-3TM designed for internal turning with the SIR system; compact toolholder for workshop and CNC lathe applications with right-hand cutting Fits 11 IR indexable inserts Shank Ø10 mm, body Ø12 mm Cutting height 20 mm for accurate seating Torx screw M2.5x5.5, key T8 supplied specification Precise geometry for repeatable internal turning operations The compact SIR S10H toolholder provides a rigid, low-mass solution for internal machining where space and repeatability matter. With a Ø12 mm body and a shank Ø10 mm, the unit keeps the centre of gravity close to the spindle, reducing vibration and improving surface finish on internal bores. The measured cutting height 20 mm ensures correct insert seating; this translates into consistent tool life and fewer re-adjustments between jobs. The lightweight construction (approx. 0.063 kg) also reduces spindle load, which is especially relevant for high-speed smaller-capacity setups. Secure insert clamping and quick indexable changes Clamping is achieved with a Torx screw specified as M2.5x5.5, tightened with a T8 driver for positive, reproducible clamping torque. Designed for 11 IR indexable inserts, the holder accepts standard IR platings and seat geometries, enabling fast replacement and minimal downtime. The right-hand cutting orientation supports conventional lathe setups and predictable chip flow. Clear mechanical interfaces reduce adjustment time, making the toolholder suitable for series work and frequent insert changes on production lines. Workshop integration and practical benefits on the shopfloor At an overall length of 100 mm, the toolholder is compact enough for tight internal operations yet long enough to access recessed features. The ISO designation SIR S10H signals compatibility with the SIR clamping family, facilitating standardisation across a tooling estate. As a ready-to-fit component, the bar simplifies inventory management: the same holder geometry can be used with compatible insert grades, so tooling diversity is reduced while maintaining machining flexibility. The construction supports stable, repeatable results on internal turning tasks without extensive machine setup. For reliable internal turning with Teknik Makina’s SIR system, contact Metav Werkzeuge in Emmerich for tailored advice and fast supply — eMail: info@metav-werkzeuge.com, Telephone: +49 2822 7131930 Technical data Article number: K337-3TM Type designation: SIR S10H Product name: SIR for IR Indexable Inserts Manufacturer: Teknik Makina Core data Diameter: 12 mm Shank diameter: 10 mm Overall length: 100 mm Cutting height: 20 mm Weight: 0.063 kg Features Fits inserts: 11 IR Cutting direction: right-hand Torx screw: M2.5x5.5 Torx key size: T8 ISO designation: SIR S10H FAQ What insert size does this toolholder accept? The toolholder accepts 11 IR indexable inserts; it is designed to match the seating geometry of standard IR inserts for reliable clamping. Which screw and driver are required for clamping? Clamping uses an M2.5x5.5 Torx screw tightened with a T8 key for repeatable seating and secure retention. Is the cutting direction suitable for conventional lathes? Yes, the toolholder is specified for right-hand cutting and is compatible with standard lathe orientations and tooling setups. What are the key dimensions to check for machine compatibility? Key dimensions are Ø12 mm body, shank Ø10 mm, and overall length 100 mm; verify these against the machine clearance and toolpost capacity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of consistent performance, simple insert changes and a rigid S16K shank for reliable boring operations. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Boring bar K337-4TM — SIR S16K holder for 11 IR indexable inserts, 12 mm dia by Teknik Makina The K337-4TM is a compact boring bar designed for precise internal turning with 11 IR indexable inserts, suitable for right-hand cutting applications in production environments. 12 mm cutting diameter for fine boring Compatible with 11 IR indexable inserts 25 mm cutting height for stable engagement S16K shaft with 16 mm shank diameter Precision where it counts: consistent bore quality with every pass The compact design of this boring bar ensures repeatable diameters and stable tool engagement in serial work. The combination of a 12 mm cutting diameter and 25 mm cutting height enables secure seating of the insert and predictable chip control; as a result, runout is reduced and surface finish is improved. Insert clamping is achieved with a standard M2.5x5.5 screw and T8 Torx key, enabling quick, toolroom-friendly replacement without special fixtures. Faster set-up and steady performance on the machine A 16 mm shank (S16K) delivers the necessary rigidity for common turning and boring cycles while keeping the overall tool length compact at 125 mm. The modest mass of 0.167 kg facilitates rapid tool changes and reduces carriage inertia during short operations, supporting higher throughput in batch production. The holder is specified for right-hand cutting and is optimised for indexable insert economics, lowering tool consumable costs and easing inventory management for workshops and subcontractors. Simple maintenance, minimal downtime Maintenance and serviceability are straightforward: the insert pocket is designed for 11 IR format plates and is secured with the supplied Torx screw type M2.5x5.5, operated with a T8 key. This standardised fastening reduces spare-part variety and simplifies staff training. The bar’s ISO designation SIR S16K clarifies mounting and compatibility, allowing compatibility checks with toolholders and turret systems to be completed quickly and reliably. Contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice on the Teknik Makina K337-4TM and to secure dependable supply from our European stock. Technical data Article number: K337-4TM Manufacturer: Teknik Makina Type designation: SIR S16K Overall length: 125 mm Weight: 0.167 kg Facts Cutting diameter: 12 mm Shank diameter: 16 mm Cutting height: 25 mm Insert format: 11 IR Screw: M2.5x5.5 Torx key: T8 Cutting direction: right Special features Compatible with IR11 clamp holder designation IR11 Compact design for reduced overhang Standardised fixing for quick insert changes ISO-style designation for straightforward integration FAQ What inserts fit the K337-4TM boring bar? The K337-4TM is designed for 11 IR indexable inserts; the pocket and clamp are matched to that format for a secure fit. Which shank size is specified for this tool? The holder is specified as S16K with a 16 mm shank diameter, ensuring rigidity in most turret and bar setups. Is the K337-4TM suitable for left-hand operations? This specific variant is configured for right-hand cutting; left-hand versions would require a different orientation. How is the insert secured in the boring bar? Insert retention is achieved with an M2.5x5.5 screw operated by a T8 Torx key, allowing quick and reliable replacement. Can the K337-4TM be used in automatic turret systems? The compact 125 mm overall length and the S16K shank make the K337-4TM suitable for many turret and bar-type tool stations, subject to machine clearance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, internal coolant and compatibility with APKT 1003 inserts for reliable, low-downtime milling operations; order the cutter via Metav Werkzeuge or consult our specialists for machining recommendations. 12 mm shank cutter for APKT 1003 indexable inserts — 120 mm overall length, internal coolant (Teknik Makina) A 12 mm shank cutter for APKT 1003 indexable inserts designed for precise, repeatable milling tasks in constrained setups and production environments. 12 mm shank diameter for compact setups Internal coolant for improved chip evacuation Compatible with APKT 1003 inserts (Korloy) Precision and rigidity for confined milling operations The compact 12 mm shank delivers a balance of rigidity and accessibility where space is limited. With a 120 mm overall length and a 27 mm cutting length, the tool body is engineered for accurate axial positioning and stable cutting performance. The combination of a firm shank and lightweight construction (approx. 0.112 kg) reduces spindle load and vibration, which in turn helps to maintain surface finish and dimensional consistency across batches. This rational configuration supports higher productivity through stable cutting conditions rather than larger, heavier tooling that may be unsuitable for tight setups. Faster insert changes and effective coolant delivery to extend tool life Designed for use with APKT 1003 indexable inserts and compatible with Korloy grades, the cutter enables quick insert replacement secured by a M2.5x5.5 Torx screw tightened with a T8 tool. The single-cutting-edge arrangement simplifies indexing and reduces downtime during regrinds or tool changes. Integral internal coolant supplies cutting fluid directly to the cutting zone, which improves chip control and reduces thermal loads—key factors in extending insert life and achieving consistent machining results. These features translate into measurable reductions in process interruptions and tooling cost per part. Operational benefits and supply reliability for production environments The tool’s straightforward design concentrates on operational efficiency: limited moving parts, a clear fastening system and accessible service procedures mean less time is spent on maintenance and more on machining. The cutter is manufactured by Teknik Makina and supplied via Metav Werkzeuge, whose Emmerich facility acts as a quality filter for the European market. This supply chain reliability ensures consistent availability and makes it simpler to standardise tooling across multiple workstations. For production planners, that equates to fewer stocking headaches and better process continuity. Contact Metav Werkzeuge for tailored machining advice or to arrange supply of this Teknik Makina shank cutter for APKT 1003 inserts; our specialists are available to discuss applications and compatibility Technical data SKU: S158-1TM Manufacturer: Teknik Makina Product type: Shank cutter Label: 12mm shank cutter APKT 1003 L120mm with internal coolant Facts Diameter: 12 mm Overall length: 120 mm Shank diameter: 12 mm Cutting length: 27 mm Weight: 0.112 kg Number of cutting edges: 1 Torx key: T8 Torx screw: M2.5x5.5 Internal coolant: Yes Special features Indexable insert type: APKT 1003 Compatible insert manufacturer: Korloy Single cutting-edge design for easy indexing Compact format for restricted setups FAQ Is this cutter compatible with APKT 1003 inserts from Korloy? Yes. The cutter is designed for APKT 1003 indexable inserts and is compatible with Korloy grades; the SKU is S158-1TM. Does the tool feature internal coolant and how does that help? The cutter includes internal coolant, which directs fluid to the cutting zone to improve chip evacuation and reduce thermal stress on the insert, increasing service life. What fastening hardware is required for the inserts? Inserts are secured with a M2.5x5.5 Torx screw using a T8 key, enabling quick and reliable insert changes. Is the shank suitable for compact machine spindles? The 12 mm shank diameter and modest overall length make this cutter suitable for confined spindle envelopes where access and rigidity are required. Can this cutter reduce downtime in series production? The combination of fast insert changes, single-edge indexing and directed coolant contributes to reduced downtime and more consistent part quality in series production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust milling solution that combines a 12 mm shank, a 30 mm effective cutting length and compatibility with common indexable inserts for reduced setup time and consistent chip evacuation. Order directly via Metav Werkzeuge or consult our specialists for machining advice and rapid supply from Emmerich. Schaftfräser — 12 mm shank, for AXMT 0602 and APKT 0903 inserts (Teknik Makina) Schaftfräser is a precision shank milling cutter designed for indexable inserts, engineered for general-purpose and production milling with standard toolholders Shank diameter 12 mm for stable clamping Compatible with AXMT 0602 / APKT 0903 inserts Two cutting edges for efficient material removal Torx screw M2.5x5.5; T6 key required Maximum rigidity for steady machining and repeatable accuracy A compact shank diameter and robust overall length deliver stable clamping that reduces run-out and vibration. With a 12 mm shaft and a total length of 120 mm, the tool is engineered to stay rigid in common collet and holder systems, which lowers chatter and improves surface finish. This mechanical stability translates into predictable tool life and fewer reworks, a direct economic benefit for frequent batch production. Predictable cutting behaviour and controlled chip removal Equipped with two cutting edges and a 30 mm effective cutting length, the cutter offers a balance between metal removal rate and surface integrity. The two-flute geometry provides consistent chip formation and evacuation, which helps maintain cutting temperatures and extends insert life. For customers unfamiliar with insert geometry: indexable inserts are replaceable cutting tips that allow fast tip exchange without regrinding, reducing downtime and tooling costs. Broad compatibility simplifies tool management Designed specifically for AXMT 0602 and APKT 0903 indexable inserts and matched with common Taegutec grades, the tool integrates into existing insert inventories with minimal changes. The Torx retention screw specification M2.5x5.5 and T6 key requirement are industry-standard details that enable quick, secure insert clamping. This compatibility reduces inventory complexity and supports a lean tooling strategy on the shop floor. Suited to workshops and production lines seeking efficiency Lightweight at about 0.119 kg, yet made to industrial tolerances, the cutter is an efficient option for both jobbing shops and larger production cells where repeatability matters. Using indexable inserts means that only the small insert needs replacing when worn, rather than the entire tool, cutting overhaul time and waste. The specification supports machining of a wide range of materials when paired with appropriate insert grades, offering a practical path to improved throughput. For reliable, supply-ready tooling from Teknik Cutting Tools and tailored advice on insert grades and holder compatibility, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss technical matching and order options. Technical Data Article number: S012TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Suitable inserts: AXMT 0602; APKT 0903 Compatible insert manufacturer: Taegutec Facts Diameter: 12 mm Shank diameter: 12 mm Cutting length: 30 mm Number of cutting edges: 2 Overall length: 120 mm Weight: 0.119 kg Torx screw: M2,5x5,5 Torx key size: T6 Special features Indexable insert shank milling cutter Two-flute geometry for reliable chip control Suited for standard collet and holder systems Compatible with common Taegutec insert grades FAQ Which insert types fit this shank milling cutter? This shank milling cutter accepts AXMT 0602 and APKT 0903 indexable inserts and is compatible with typical Taegutec grades for different materials and finishes. What toolholder and clamping are required? A standard collet or holder matching a 12 mm shank is suitable; secure inserts with the specified Torx screw M2.5x5.5 using a T6 key. How many cutting edges does the cutter have and what is the benefit? The tool features two cutting edges, which balance effective material removal with controlled chip evacuation and consistent surface finish. Is the torque screw and key supplied with the tool? The specification lists the required Torx screw size (M2.5x5.5) and key (T6); availability in the delivery set should be confirmed with the supplier prior to purchase. Can this cutter be used for finishing passes? Yes—when paired with appropriate insert grades and correct feed settings, the cutter is suitable for both roughing and finishing operations on common workpiece materials. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of proven compatibility with APMT 0602 indexable inserts, a rigid 12 mm shank and a 25 mm cutting height for consistent shoulder milling; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. S028TM — Shank Milling Cutter for APMT 0602 Indexable Inserts (Teknik Makina) A compact S028TM shank milling cutter engineered for use with APMT 0602 indexable inserts, intended for robust face and shoulder milling in industrial CNC applications. *Fits APMT 06 indexable inserts *12 mm shank diameter for rigidity *25 mm cutting height for deep passes *Torx fastening M1.8×4.1, T6 key Proven insert system for predictable costs and uptime This shank-mounted cutter uses standard APMT 0602 indexable inserts, allowing fast insert changes and predictable running costs. The combination of a repeatable insert seat and Korloy-compatible geometry reduces cycle-to-cycle variation and minimises the need for full-tool replacement. By employing replaceable cutting edges rather than a monolithic cutter, machining operations gain economic advantages through reduced tooling expenditure and shorter machine downtime, improving overall process efficiency. Rigid shank and geometry for stable cutting performance The 12 mm shank together with a 100 mm overall length provides a favourable balance between reach and stiffness, which helps to lower vibration during shoulder milling. A 25 mm cutting height enables deeper material engagement per pass while the 90° cutting angle produces square shoulders and reliable face finishes. The tool’s modest mass (approximately 0.08 kg) reduces spindle load during rapid acceleration, contributing to smoother tool paths and consistent surface quality. Quick insert changes and straightforward maintenance Insert clamping is secured with a M1.8×4.1 Torx screw tightened with a T6 key, enabling safe, repeatable clamping torque and swift changeover. The use of indexable inserts simplifies upkeep: worn edges are replaced in seconds without regrinding, which shortens maintenance cycles and keeps production running. Clear identification of fastening parts and standard key sizes helps maintain a controlled spare-parts inventory on the shop floor. Application scope and workshop integration Designed for general face and shoulder milling with APMT 0602 inserts, the tool performs well in batch and series production where cost-efficiency and quick tool exchange are priorities. The holder’s compatibility with widely used insert sizes and Korloy inserts supports flexible process planning and easy sourcing of cutting edges. For operations requiring modularity and straightforward logistics, this cutter integrates neatly into an existing tool carousel or turret system. For tailored application advice or immediate supply of the Teknik Makina S028TM shank milling cutter, contact Metav Werkzeuge in Emmerich for expert guidance and fast delivery: +49 2822 7131930, info@metav-werkzeuge.com Technical Data Article number: S028TM Product: Shank milling cutter for APMT 0602 indexable inserts Manufacturer: Teknik Makina Specifications Shank diameter: 12 mm Diameter: 12 mm Overall length: 100 mm Cutting height: 25 mm Cutting edges: 3 Weight: 0.08 kg Cutting angle: 90° Features Compatible with Korloy APMT 06 inserts Torx screw M1.8×4.1 Torx key size T6 Indexable insert type APMT 0602 Brand: Teknik Makina FAQ Which insert type fits this shank milling cutter? The holder accepts APMT 0602 indexable inserts; compatible inserts from Korloy are recommended for a good fit. How many cutting edges does the tool have? The cutter uses three cutting edges; the holder itself accommodates three insert positions for balanced cutting forces. What is the shank diameter and why does it matter? The shank measures 12 mm, offering improved stiffness compared with smaller shanks and better resistance to deflection during shoulder milling. Which fastening hardware is required for insert clamping? Insert clamping uses a Torx screw M1.8×4.1 tightened with a T6 key for secure, repeatable clamping. Is the tool suitable for face and shoulder milling? Yes; the 90° cutting angle and 25 mm cutting height make it suitable for reliable face and shoulder milling tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise holemaking, compatibility with Korloy indexable inserts and a compact shank for stable clamping — all designed to keep cycle times low and tooling costs predictable. Order the indexable insert drill body directly via Metav Werkzeuge or ask our consultants if needed. Indexable Insert Drill Body U20TM — 12 mm diameter, 16 mm shank (Teknik Makina) A robust Indexable Insert Drill Body U20TM engineered for precision holemaking with Korloy XCMT 060204 indexable inserts in metalworking and toolroom applications. 12 mm cutting diameter 36 mm effective cutting length 16 mm precision shank Compatible with Korloy XCMT 060204 Accuracy and predictable hole quality for production runs The design delivers a consistent holemaking solution where repeatability matters. With a 12 mm diameter and an overall length of 94 mm, the tool body is dimensioned for a wide range of machining setups while retaining a compact footprint. The effective cutting length of 36 mm provides a well-defined engagement zone which helps stabilise the cutting forces; this stability is translated into more uniform hole diameters and reduced rework rates. Where tight tolerances are required, the use of an insert system ensures that cutting geometry can be restored precisely after each index or replacement. Indexable inserts for rapid service and lower running costs Compatibility with XCMT 060204 indexable inserts from Korloy gives shops a clear economic advantage: the cutting edge can be renewed by indexing or replacing the insert rather than regrinding the whole tool, reducing downtime and inventory complexity. The modular concept is particularly effective for mixed-batch production or when multiple grades of carbide are needed. The system is suited to pragmatic workshop logistics because different insert grades can be stocked independently from the body, enabling fast adaptation to varying materials and machining conditions. Stable clamping and toolholder integration A 16 mm shank with a 45 mm shank length ensures secure clamping in standard holders, which reduces vibration and improves surface finish. The relatively light mass (approx. 0.114 kg) also aids spindle balance for shorter overhangs, while the overall construction is optimised to transfer torque and resist deflection where drilling depth is moderate. These characteristics mean the drill body is readily integrated into existing toolholders and collet systems without elaborate fixturing, supporting efficient changeovers on the shopfloor. Workshop suitability and operational overview The component is supplied as a drill body compatible with established insert formats and is identified under SKU U20TM. Its layout supports conventional holemaking tasks across general steelworking and similar applications where indexable insert tooling is preferred for productivity and maintainability. Technical teams will appreciate that the modular approach simplifies maintenance planning and sharpens cost-per-hole calculation, enabling clearer decisions about tooling lifecycle and replacement strategy. For specification checks or to confirm fitment with a particular machine setup, further technical details can be provided. For tailored advice on Teknik Makina drill bodies and to confirm Korloy XCMT 060204 compatibility, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: U20TM Manufacturer: Teknik Makina Designation: Indexable insert drill body (Vollbohrer) ECLASS: 21180201 Facts Diameter: 12 mm Overall length: 94 mm Cutting length: 36 mm Shank diameter: 16 mm Shank length: 45 mm Weight: 0.114 kg Special features Compatible with Korloy XCMT 060204 inserts Suitable for indexable insert systems SKU: U20TM Manufacturer: Teknik Makina FAQ Which insert type fits this drill body? The drill body accepts XCMT 060204 indexable inserts; it is specified for use with Korloy insert geometry. What shank size is required for clamping? A 16 mm shank diameter and a 45 mm shank length are specified for stable clamping of the U20TM body. What hole depth can be achieved reliably? The effective cutting length is 36 mm, which defines the recommended engagement length for consistent drilling performance. Is the drill body suitable for general steelworking? Yes — the modular insert concept and the mechanical design of the U20TM make it well suited for typical steel machining where indexable tooling is preferred. How much does the tool weigh and how does that affect balance? The tool weight is approx. 0.114 kg; the relatively low mass helps maintain spindle balance at modest overhangs and supports smoother operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision-oriented drilling solution that combines a 12 mm cutting diameter, a 27 mm cutting length and a secure 16 mm shank for reliable clamping and repeatable bore quality; order the Solid Drill U032TM directly via Metav Werkzeuge or ask our consultants if needed Solid Drill U032TM by Teknik Makina — 12 mm cutting diameter, 85 mm overall length A Solid Drill U032TM designed for precision drilling applications, offering a 12 mm cutting diameter and a 27 mm effective cutting length for controlled material removal Solid construction for consistent bore quality 12 mm cutting diameter with 27 mm cutting length Compatible with Korloy QC--060204 indexable inserts Consistent bore quality through defined cutting geometry The compact design delivers repeatable results by combining a controlled cutting length with a balanced flute profile. With a 12 mm diameter and 27 mm cutting length, the tool is engineered to create clean bores while limiting vibration; this reduces rework and improves spindle life. The cutting geometry is optimised for stable chip evacuation when used with compatible indexable systems, translating technical features into measurable productivity gains for production or job-shop environments. Secure clamping and machine compatibility for stable operation A solid shank arrangement provides dependable clamping and precise runout under load. The tool features a 16 mm shank and a 45 mm shank length, while the overall length is 85 mm, which ensures compatibility with standard collet chucks and toolholders that accept this shank size. The low mass (0.1 kg) reduces centrifugal imbalance at speed, so the component is suitable for toolholders where concentricity and rigidity are priorities. Proven insert compatibility and tooling flexibility Designed for use with indexable systems, the drill body accepts the specified insert type Korloy QC--060204, enabling quick insert changes and reduced downtime compared with regrinding solid cutters. This arrangement allows a workshop to combine the efficiency of indexable inserts with the precision of a rigid drill body. For users seeking higher process uptime, the modular approach simplifies inventory: keep a small number of bodies and a supply of inserts for fast turnarounds. Service, sourcing and workshop integration Supply and specialist advice are provided directly from a European distribution channel, ensuring steady availability and clear logistics. The product is delivered with concise specification data so that toolroom planners and buyers can verify fitment before installation. For complex setups or machine-specific queries, Metav Werkzeuge offers technical guidance and fast responses from its Emmerich location, helping to integrate the tool into existing machining cycles with minimal interruption. Contact Metav Werkzeuge for tailored advice on the Teknik Cutting Tools Solid Drill U032TM — technical support and supply directly from Emmerich, email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: U032TM Manufacturer: Teknik Makina Brand: Teknik Cutting Tools Dimensions & measurable data Diameter: 12 mm Overall length: 85 mm Cutting length: 27 mm Shank diameter: 16 mm Shank length: 45 mm Weight: 0.1 kg Compatibility & features Fits Korloy indexable inserts QC--060204 Designed for toolholders accepting 16 mm shanks Solid drill body type FAQ What insert type fits this drill body? The drill body accepts Korloy indexable inserts coded QC--060204, allowing fast replacement without regrinding the body Which shank size is required for the toolholder? The tool is supplied with a 16 mm shank and 45 mm shank length; the holder must accept a 16 mm diameter shank for secure clamping What are the primary dimensions to check before purchasing? Verify the 12 mm diameter, 85 mm overall length and 27 mm cutting length match the machining task and the available toolholder envelope Is this product suitable for high-speed spindles? The drill’s balanced design and low mass (0.1 kg) support rotational stability; final suitability depends on machine parameters and cutting data How are replacement inserts sourced? Replacement indexable inserts for the system are standard Korloy QC--060204 items; maintain an insert stock to reduce downtime Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, indexable drilling with the combination of a 12 mm diameter, a 72 mm total length and direct compatibility with XC-- 060204 indexable inserts. Order directly via Metav Werkzeuge for reliable supply and expert consulting if additional technical information is required. 12 mm Solid Drill for XC-- 060204 Indexable Inserts (L72 mm) – Teknik Makina The 12 mm Solid Drill for XC-- 060204 Indexable Inserts is a compact indexable-drill body designed for reliable short-reach drilling in production and toolroom environments. 12 mm diameter for compact drilling Compatible with XC-- 060204 inserts 72 mm total length for limited reach 45 mm shank ensures stable clamping Precision and compatibility for productive machining The solid drill body is engineered for reproducible hole-making where changeable cutting edges speed up maintenance cycles. With a 12 mm diameter and 72 mm overall length, the tool combines compact geometry with sufficient reach for many common through-hole and short-depth applications. Compatibility with XC-- 060204 indexable inserts, including those by Ceratizit, enables fast index-and-go insert changes, reducing machine downtime and increasing throughput. The modular concept allows consistent hole quality without the need for full regrinding, which supports efficient batch processing and predictable cycle times. Stable clamping and straightforward servicing reduce downtime A 45 mm shank provides a secure interface for most collet and chuck systems, ensuring concentricity under machining loads and minimising runout. The 27 mm cutting length is optimised for chip evacuation in short-depth drilling, while the fastening arrangement—secured with a T7 Torx key and M2,2x5 Torx screw—permits rapid insert replacement and repeatable clamping torque. The indexed head arrangement means service technicians can restore cutting performance quickly, which translates into lower operating costs and more consistent component tolerances across production runs. Suitable workshop applications and supply confidence Designed for workshop and small-series production, this drill body (SKU U062TM) is light at 0.1 kg, easy to handle and intended for integration into CNC drilling cycles where indexable solutions are preferred. The modular design benefits maintenance teams and purchasing managers alike: spare inserts and screws are standardised, reducing inventory complexity. Metav’s position as a quality filter for the European market adds assurance—consistent availability from a centralised stock in Emmerich supports reliable replenishment and supplier consolidation for precision tooling needs. Contact Metav Werkzeuge for expert advice on Teknik Makina indexable drilling systems and to arrange timely supply – eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: U062TM Product type: Solid drill Brand: Teknik Makina Label: 12mm Vollbohrer XC-- 060204 L72mm Data Diameter: 12 mm Total length: 72 mm Cutting length: 27 mm Shank length: 45 mm Weight: 0.1 kg Special features Compatible with XC-- 060204 indexable inserts Compatible with Ceratizit inserts T7 Torx key fastening Torx screw M2,2x5 Indexable head design SKU: U062TM FAQ Which indexable inserts fit this drill? The drill body accepts XC-- 060204 indexable inserts; compatibility with Ceratizit inserts is specified for the 12 mm Solid Drill (SKU U062TM). How is the insert secured to the drill head? Inserts are fastened using a T7 Torx key and an M2,2x5 Torx screw, allowing secure clamping and straightforward replacement for the Teknik Makina drill body. What applications suit this drill body best? The tool is designed for short-reach drilling in CNC machining and production workshops where quick insert changes and reproducible hole quality are priorities. What should be considered for clamping? Use a secure clamping system compatible with the 45 mm shank to ensure concentricity and minimise runout during operation of the solid drill. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from accurate chip control and rapid insert changes thanks to compatibility with XC-- 060204 indexable inserts and a compact 12 mm cutting diameter; order the tool directly via Metav Werkzeuge or ask their consultants for application advice. Indexable-insert drill — 12 mm diameter, 72 mm overall length, Teknik Makina A 12 mm indexable-insert drill designed for use with XC-- 060204 indexable inserts, ideal for precision drilling in compact parts and production setups 12 mm cutting diameter for compact centres Compatible with XC-- 060204 indexable inserts Overall length 72 mm for deep-hole positioning Torx T7 screw with M2.2x5 fastening High performance from a compact diameter The compact 12 mm diameter provides a balance between access to confined spaces and the rigidity required for repeatable hole quality. By accepting XC-- 060204 indexable inserts, the tool combines the economy of replaceable cutting edges with the predictability of a rigid drill body. For machining centres that demand consistent bore tolerance and surface finish, this configuration reduces cycle-time variation and supports efficient tool rotation speeds while maintaining stability at the cutting edge. Predictable setup and depth control for serial work A total length of 72 mm and a clearly defined 27 mm cutting length deliver controlled engagement depth and straightforward tool set-up in a toolholder. The specified overall and cutting dimensions help to calculate safe overhang and runout allowances, which contributes to reduced vibration and extended insert life. The compact mass and measured geometry also aid in maintaining concentricity during high-volume production, translating into fewer scrap parts and a more predictable process window. Fast, secure inserts for lower downtime Insert retention uses a Torx T7 interface with an M2.2x5 fastening screw, providing repeatable, high-clamp reliability and simple serviceability. The standardised screw drive shortens changeover time and supports quick reconditioning of the cutting edge without specialised tooling. Together with the indexable-insert principle, this arrangement minimises machine downtime and keeps line output steady, which is particularly valuable in batch manufacturing and mixed‑series production. Designed for industrial use and straightforward logistics The drill body is supplied in a compact format and weighs approximately 0.1 kg, making handling and storage efficient for workshop environments. Compatibility with ISCAR-manufactured inserts and the clear SKU identification (U046TM) ease procurement and stock-keeping. The design suits CNC spindle applications where a reliable, exchangeable cutting system is preferred over solid-tool regrinding, supporting a pragmatic balance between lifecycle cost and machining performance. Discuss compatibility and availability with Metav Werkzeuge — contact the Metav specialists in Emmerich for technical guidance and delivery information at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: U046TM ECLASS: 21180201 Label: 12mm Vollbohrer XC-- 060204 L72mm UID: U046TM Core data Diameter: 12 mm Overall length: 72 mm Cutting length: 27 mm Shank/holder length: 45 mm Weight: 0.1 kg Features & compatibility For XC-- 060204 indexable inserts Compatible insert maker: ISCAR Torx T7 screw, M2.2x5 fastening Product type: Indexable-insert drill FAQ What are the main dimensions of the tool? The indexable-insert drill (SKU U046TM) has a 12 mm diameter, 72 mm overall length and a 27 mm cutting length for controlled depth drilling. Which inserts fit this drill? This drill accepts XC-- 060204 indexable inserts; the assembly is compatible with inserts from ISCAR as specified. How are the inserts secured and serviced? Inserts are secured with a Torx T7 drive using an M2.2x5 screw, allowing secure clamping and quick replacement during routine maintenance. Is the tool suitable for CNC production? Yes — the drill body from Teknik Makina is designed for spindle mounting in CNC machines and for serial production where quick insert changes support uptime. What is the product SKU and weight for logistics? The product is listed as SKU U046TM and has an approximate weight of 0.1 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, reliable milling solution with internal coolant and compatibility for APMT 0602 indexable inserts — ideal for precise finishing and medium-duty roughing. Benefit from the 12 mm shank for stable clamping and quick insert changes; order directly via Metav Werkzeuge or consult our specialists for application guidance. Shank milling cutter S028-1TM – internal coolant, for APMT 0602 indexable inserts (Teknik Makina) A versatile shank milling cutter designed for use with APMT 0602 indexable inserts, offering internal coolant and a 12 mm shank for compact, precise machining in versatile production environments. Internal coolant channels for secure chip evacuation Compatible with APMT 0602 indexable inserts 12 mm shank for compact toolholders Torx T6 fastening with M1.8×4.1 screw Improved machining throughput with dependable cutting performance This milling body combines a compact design with features aimed at production efficiency. The integrated internal coolant reduces thermal load at the cutting edge and supports consistent cutting conditions, which leads to more predictable tool life and less rework. Using replaceable APMT 0602 indexable inserts simplifies tool management: worn edges are replaced in seconds rather than replacing the entire tool, helping to maintain productivity during volume machining and reducing total tooling costs. Faster set-up and consistent clamping for repeatable accuracy A 12 mm shank and balanced geometry reduce vibrations in small to medium-sized toolholders, improving surface finish and dimensional stability during passes. The cutter’s secure fastening system, operated with a Torx T6 key and the M1.8×4.1 screw, enables rapid insert changes and consistent clamp force, lowering set-up times and minimising variability between shifts. For workshops seeking reproducible results, this combination supports tighter tolerances with minimal overhead. Effective cooling and chip control enhance tool life The internal coolant circuit feeds the cutting zone directly, supporting effective chip evacuation and cooling where it matters most. This targeted coolant delivery helps to stabilise temperatures at the insert corner and reduce built-up edge formation, which in turn preserves the insert life and maintains cutting performance over longer cycles. For operations requiring consistent surface quality, the internal coolant is a pragmatic advantage over conventional external-only cooling. Simple compatibility and serviceability for industrial use Configured specifically for APMT 0602 format inserts and compatible with inserts from Korloy, the cutter integrates smoothly into existing insert inventories. The lightweight construction and compact overall length make it suitable for flexible machining tasks where space and balance are important. Routine maintenance is straightforward thanks to the standardised screw and key interface; replacement parts and accessories are easy to source to keep downtime to a minimum. Contact Metav Werkzeuge for tailored application advice and to secure the Teknik Makina shank milling cutter S028-1TM with internal coolant for immediate integration into production Technical data Article number: S028-1TM Label: 12mm Schaftfräser APMT 0602 L100mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 12 mm Shank diameter: 12 mm Overall length: 100 mm Cutting length (shank): 25 mm Weight: 0.075 kg Number of cutting edges: 3 Special features Internal coolant For APMT 0602 indexable inserts Compatible with Korloy inserts Torx T6 key required Torx screw M1.8×4.1 FAQ Can this cutter be used with Korloy APMT 0602 inserts? Yes. The S028-1TM is configured for APMT 0602 inserts and is listed as compatible with Korloy insert types, enabling straightforward integration with those inserts. What key and screw are required to change an insert? Insert changes on the S028-1TM are performed using a Torx T6 key and the M1.8×4.1 Torx screw provided for secure clamping. Is the coolant supplied through the tool body? Yes. The cutter features internal coolant channels that deliver fluid directly to the cutting zone to support chip evacuation and extend insert life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑precision tool that combines a 12 mm shank, internal coolant and a three‑edge configuration for stable, efficient milling; order the S705TM directly via Metav Werkzeuge or contact our consultants for tailored tooling advice. Shaft milling cutter S705TM for LNMU 0202 indexable inserts — 12 mm shank, internal coolant (Teknik Makina) Shaft milling cutter S705TM designed for interchangeable LNMU 0202 indexable inserts, offering a compact solution for versatile milling tasks in industrial workshops and precision production. 12 mm shank diameter for compact toolholders Internal coolant delivery for improved chip evacuation Compatible with LNMU 0202 indexable inserts by Tungaloy Three cutting edges for stable, efficient machining Stable cutting performance for consistent production quality The S705TM is engineered to deliver repeatable stability in demanding milling operations. With a 12 mm shank and a modest 30 mm cutting length, the tool minimises overhang and vibration, which translates into better surface finishes and extended insert life. The three‑edge geometry balances cutting forces to provide steady engagement with the workpiece, making the shank cutter particularly suitable for operations where tool rigidity and consistent results are priorities. Optimised coolant routing to protect tool life and workpiece finish Integrated internal coolant channels ensure coolant reaches the cutting zone directly, improving chip evacuation and aiding heat dissipation at the insert seat. This direct supply reduces thermal load on the insert, which supports longer service intervals and more reliable dimensional control. For shops seeking to maintain productivity without frequent tool changes, the internal coolant feature contributes to lower downtime and more consistent part quality. Seamless integration with indexable insert systems and quick servicing Designed for use with LNMU 0202 indexable inserts and compatible with Tungaloy inserts, the design permits rapid insert replacement and straightforward maintenance. The tool accepts the specified Torx fixing (T6) and screw (M1.8x4.1), allowing assembly and clamping with common workshop tools. At 140 mm overall length and a weight of 0.155 kg, the cutter offers a practical balance between reach and handling, fitting many standard milling holders without requiring excessive adapter lengths. Contact Metav Werkzeuge today for expert guidance on integrating the Teknik Makina S705TM into production or to request a specification sheet and supply options from our Emmerich team Technical data Article number: S705TM Manufacturer: Teknik Makina Product type: Shank milling cutter Facts Cutter diameter: 12 mm Shank diameter: 12 mm Overall length: 140 mm Cutting length: 30 mm Number of cutting edges: 3 Weight: 0.155 kg Special features Internal coolant Compatible with LNMU 0202 indexable inserts Compatible insert manufacturer: Tungaloy Torx key: T6 Torx screw: M1.8x4.1 FAQ Which insert type fits this shank milling cutter? The cutter accepts LNMU 0202 indexable inserts; Tungaloy‑spec inserts are listed as compatible with the S705TM shank milling cutter. Is coolant delivered through the cutter? Yes, the tool features internal coolant channels to supply coolant directly to the cutting zone for improved chip control and thermal management. How many cutting edges does the cutter have and what is the benefit? The cutter has three cutting edges, which support stable cutting forces and improved runout tolerance, contributing to better surface finish and insert life. What fastening hardware is required for insert changes? Insert clamping uses a Torx T6 key and M1.8x4.1 screw for secure and repeatable insert seating on the S705TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precise holder that combines a 12 mm clamping section and a 125 mm overall length to support efficient grooving and parting operations; order the parting tool holder directly via Metav Werkzeuge or consult our specialists for application advice. Parting tool holder DGN — grooving and parting holder with 12 mm clamp, Teknik Makina Parting tool holder DGN is a compact grooving and parting holder designed for industrial turning applications, optimised for ISCAR DGN 2C inserts and short-reach operations Compact 12 mm clamp width for tight grooves Compatible with ISCAR DGN 2C inserts M4x10 hex screw with T15 key for secure clamping 125 mm overall length for stable tool mounting Precision performance in tight spaces The DGN parting holder delivers precise positioning thanks to its standardised 12 mm clamp and ISO 1212 reference, which together reduce play and ensure repeatable cuts. Designed for short overhangs, the holder’s 125 mm overall length minimises deflection during cut-off and grooving tasks, improving dimensional accuracy and surface finish. This compact geometry is particularly useful where machine-tool clearance is limited and consistent cutting performance is required. Secure clamping and straightforward maintenance Clamping is effected with an M4x10 hex screw tightened using a T15 hex key, providing a reliable connection between holder and insert without complex adjustments. The simple clamping mechanism speeds up insert changes and routine checks, reducing downtime. At a mere 0.14 kg, the holder is light enough for quick handling while remaining rigid during operation, making maintenance procedures faster and less physically demanding. Compatibility that simplifies tooling logistics Specified for DGN 2C inserts and tested for use with ISCAR cutting grades, the holder integrates seamlessly into existing tooling setups that already use DGN-format inserts. The standardised interface permits straightforward interchangeability of inserts and supports common workpiece materials encountered in high-quality steel machining. This compatibility eases inventory management and lowers the barrier to adopting specialised grooving operations on the shop floor. Practical limits and application focus The holder supports a maximum plunge depth of 12 mm and a cutting width of 2 mm, parameters that define its suitability for narrow-slot and parting operations. These limits make the tool ideal for finishing narrow grooves, parting small-diameter workpieces and operations that prioritise surface integrity over bulk material removal. For heavy interrupted cuts or deep shoulder grooving, select tooling with larger cross-sections or greater overhang capacity. For reliable grooving and precise parting operations, select the Teknik Makina DGN parting tool holder via Metav Werkzeuge — contact our consultants for tailored recommendations and to confirm fitment in specific turning applications Technical data Article number: D019TM Manufacturer: Teknik Makina Numbers / Core technical data Clamp width: 12 mm Clamp height: 12 mm Cutting head width: 12.2 mm Overall length: 125 mm Overall height: 12 mm Max plunge depth: 12 mm Cutting width: 2 mm Weight: 0.14 kg Special features Compatible inserts: DGN 2C Suitable for insert brand: ISCAR Hex screw: M4x10 Hex key: T15 ISO designation: 1212 Holder bore designation: 2C DGN FAQ What insert types are compatible with this holder? The parting tool holder DGN accepts DGN 2C inserts and is specified for use with ISCAR DGN grades, ensuring plug‑and‑play compatibility for common grooving inserts. What is the maximum cutting depth for this holder? The holder supports a maximum plunge depth of 12 mm, which defines its effective range for grooving and cut‑off tasks. Which screw and key are required for clamping the insert? Clamping is secured with an M4x10 hex screw and requires a T15 hex key for correct torque and repeatable fixation. Is this holder suitable for steel machining? Yes; the holder is designed for high-quality steel machining, matching the demands of accurate grooving and parting in industrial lathe work. How does the holder affect tool rigidity and accuracy? With a compact 125 mm overall length and a 12 mm clamp, the design minimises overhang and reduces deflection, which improves cutting accuracy and surface finish during parting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, repeatable parting operations thanks to secure clamping and a narrow 2 mm cutting width, combined with quick insert compatibility for efficient changeovers; order directly from Metav Werkzeuge or contact our consultants for compatibility advice. Parting tool holder KGMN — 12 mm height, 2 mm cut width, Teknik Makina A compact Parting tool holder KGMN engineered for controlled parting and grooving on lathes and turning centres, designed around Korloy KGMN 200 inserts for reliable metal‑cutting applications. Parting tool holder for KGMN 200 inserts 2 mm cutting width for narrow grooves Secure clamp with M4x10 fastening 125 mm overall length, 12 mm height Consistent clamping for precision parting A sturdily machined clamp body provides reliable fixation of the insert, reducing movement under load and helping to sustain repeatable tolerances. The holder’s M4x10 fastening and supplied hex key size T15 ensure a firm, serviceable connection between insert and bar; this straightforward mechanical design keeps set‑up times short and maintenance predictable. For shops seeking process stability, the compact geometry contributes to reduced vibration and steadier finish quality on workpieces. Narrow‑groove performance that improves surface quality With a 2 mm cutting width and a cutting‑head envelope of 12.2 mm, the holder is optimised for tight parting and grooving operations where clearance is limited. The maximum plunge depth of 12 mm gives sufficient engagement for many through‑parting and grooving jobs while the slim cut width minimises material removal and cutting forces. In practice this translates to less heat buildup, a cleaner chip flow and better surface integrity on the finished component. Built for efficient workshop handling Weighing just 0.13 kg and finished to standardised ISO dimensions (ISO 1212), the holder is easy to handle during tool changes and aligns with common bar systems. The overall length of 125 mm and a total height of 12 mm fit compact tool posts and allow rapid indexing in many turning centres. The low mass reduces inertial forces during acceleration, helping to preserve insert life and enabling confident, repeatable setups in production or jobbing environments. Compatibility and quick changeover with Korloy inserts Designed specifically for Korloy KGMN 200 inserts and documented as compatible with bar designation 2C KGMN 200, the holder supports fast replacement of cutting edges and straightforward tool management. The adherence to recognised insert geometry and the presence of a standard clamping screw mean swaps are predictable and can be integrated into existing tool‑holding inventories. Where machining flexibility matters, this holder provides a compact, industry‑aligned option for parting and grooving tasks. Contact Metav Werkzeuge for technical advice and to arrange supply of this Teknik Cutting Tools parting tool holder from our Emmerich warehouse. Technical data Article number: D016TM Manufacturer: Teknik Makina eClass: 21181005 Dimensions & weight Holder width: 12 mm Holder height: 12 mm Cutting head width: 12.2 mm Cutting width: 2 mm Max plunge depth: 12 mm Overall length: 125 mm Overall height: 12 mm Weight: 0.13 kg Compatibility & fastenings Compatible with Korloy KGMN 200 inserts Bar designation: 2C KGMN 200 Clamping screw: M4x10 Hex key size: T15 ISO designation: 1212 FAQ What insert type fits this holder? The holder is compatible with Korloy KGMN 200 inserts and accepts the standard geometry used for that series. What is the cutting width and how does that affect use? The 2 mm cutting width allows narrow parting and grooving where minimal material removal and low cutting forces are required. Which fastening components are included or required? Fastening is by an M4x10 screw; torque should be applied with a T15 hex key to secure the insert correctly. Is the holder suitable for production turning centres? Yes — the compact parting tool holder KGMN with 125 mm overall length and ISO‑aligned dimensions is designed for reliable use in production and jobbing environments. How deep can the holder cut in a single plunge? The maximum plunge depth is 12 mm, suitable for many through‑parting and groove‑cutting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact 12 × 12 mm clamping cross-section together with a 2 mm cutting width and up to 16 mm plunge depth for precise, repeatable grooving and parting operations; order the holder directly via Metav Werkzeuge or consult the team for application advice. Parting and Grooving Clamping Holder – 2 mm cutting width, 16 mm max plunge (Teknik Makina) A sturdy Parting and Grooving Clamping Holder for use with indexable inserts, engineered for precise 2 mm grooving and controlled parting in standard turning set-ups *Compatible with TNGLY-OKE 2C DGM 2 inserts *2 mm cutting width for fine grooving *Max plunge depth 16 mm for deep cuts *Compact 12 x 12 mm clamping cross-section Stable clamping for repeatable groove geometry The holder delivers consistent clamping thanks to its compact 12 × 12 mm cross-section and low overall mass (0.166 kg), which together reduce tool overhang and vibration during parting operations. With a 2 mm cutting width and 16 mm maximum plunge depth, the design supports accurate groove profiles and repeatable parting without undue deflection. For workshops that prioritise dimensional control, the combination of a short, rigid shank and a secure clamp ensures improved surface finish and fewer reworks. The use of indexable inserts means straightforward insert replacement and predictable cutting behaviour. Rapid integration into lathe toolposts and clear interface data Integration into existing tooling is simplified by the standardised shank and designation data: ISO designation 1212 and shank type 2C‑DGM 2 are specified for straightforward referencing in tool lists and holders. The overall length of 125 mm keeps the centre of gravity close to the machine, while the clearly defined head and shank dimensions (12 mm height and 12 mm head width) make it easy to set up in toolposts or quick-change systems. These measurable values support planning in production: matching the holder to the lathe’s toolpost geometry avoids unnecessary adapters and preserves rigidity at the cutting point. Practical reliability for everyday turning tasks and workshop efficiency Built for routine use with TNGLY‑OKE indexable inserts, this clamping holder balances simplicity with robust function. The compact format and defined mechanical interfaces reduce set-up variability and support a steady production rhythm. Metav’s emphasis on accessible precision means this product is supported from stock in Emmerich, backed by decades of distribution experience and a broad portfolio that helps reduce supplier complexity. The result is a dependable solution that fits into established workflows and helps maintain consistent throughput. Contact Metav Werkzeuge for tailored advice on integrating this Teknik Makina parting and grooving holder into production; Metav Werkzeuge in Emmerich provides fast supply and application consultation – eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: D842TM Manufacturer: Teknik Makina Type designation (ISO): 1212 Shank designation: 2C-DGM 2 Compatible insert manufacturer: TNGLY-OKE Numbers / Core technical data Cutting width: 2 mm Max plunge depth: 16 mm Clamping height: 12 mm Head width: 12 mm Clamping width: 12 mm Overall length: 125 mm Weight: 0.166 kg Special features / Design For indexable inserts: 2C DGM 2 Clamping style: parting/grooving holder ISO reference available: 1212 Short, rigid form factor for reduced vibration FAQ Which insert type fits this holder? This parting and grooving clamping holder accepts 2C DGM 2 indexable inserts and is specified for TNGLY‑OKE inserts in the product data. What is the maximum cutting width and plunge capability? The holder supports a 2 mm cutting width and a maximum plunge depth of 16 mm, suitable for fine grooving and controlled parting operations. How is the holder designated for tool lists and ordering? Refer to SKU D842TM and ISO designation 1212 for ordering and tool list entries; the shank designation 2C‑DGM 2 clarifies mounting requirements. Will this holder fit standard quick-change toolposts? The compact 12 × 12 mm clamping cross-section and the 125 mm overall length make the holder compatible with common lathe toolposts and quick-change solutions where the shank form matches. What benefits does the compact form deliver on the lathe? A shorter, rigid shank reduces overhang and vibration, improving surface finish and dimensional consistency during parting and grooving. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Taking advantage of a compact 12 x 12 mm shank combined with a 2 mm cutting width ensures precise, repeatable grooving operations and reduced setup times; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Grooving clamp holder (Stechklemmhalter) by Teknik Makina — 12 x 12 mm, 2 mm cutting width The Grooving clamp holder (Stechklemmhalter) is a left-hand grooving tool holder designed for a 12 x 12 mm shank and 2 mm cutting width, compatible with Korloy 2C MGM indexable inserts for medium-depth parting and grooving tasks. Compact 12 x 12 mm shank 2 mm cutting width for narrow grooves Left-hand cutting direction Compatible with Korloy 2C MGM inserts Accuracy and control for tight groove tolerances The compact 12 x 12 mm shank delivers a stable interface between holder and lathe toolpost, improving precision when producing narrow grooves. The slender 2 mm cutting width is suited to operations where minimal material removal is required while maintaining dimensional control. Thanks to the low mass (0.161 kg) and rigid geometry, vibration is reduced and repeatability is improved; this supports consistent part quality across batch runs and shortens rework cycles. The design is optimised for controlled chip flow and reliable clamping, which contributes to longer effective tool life and fewer interruptions. Robust clamping and clear compatibility for quick tool setup Built around an ISO-style designation and a dedicated bar configuration, the holder accepts Korloy 2C MGM plates and matches the ISO 1212 format and 2C-L MGM bar designation. The clamping concept secures indexable inserts reliably for turning and grooving tasks: indexable inserts permit fast replacement without regrinding, reducing downtime. The left-hand orientation is specified for tools that machine in the leftward cutting direction; this should be matched to the lathe’s setup. The clear nominal dimensions make tool selection straightforward for workshop engineers and purchasing teams. Productivity gains through predictable cutting limits A maximum plunge capability of 16 mm provides defined limits for deeper grooving operations within the holder’s intended range. Predictable cutting parameters and the holder’s compact footprint help to maintain cycle-time targets by enabling consistent feed rates and stable cutting conditions. The combination of small cutting width and secure clamping assists in achieving fine surface finishes with less secondary processing. Where part tolerances are critical, this holder supports efficient production by aligning mechanical stability with practical cutting depths. Application fit and handling considerations The holder’s modest overall length (125 mm) and clear 12 x 12 mm shank dimensions make it suitable for confined toolpost arrangements and multi-tool turrets where space is limited. Installation follows standard mounting practices for clamping holders of this class, and the left-hand cutting direction must be taken into account during tool promenade planning. Spare insert compatibility with Korloy’s 2C MGM family simplifies stocking and logistics. For users requiring further specification data or adaptation to bespoke machine interfaces, supplementary technical guidance is available to ensure the holder integrates correctly into existing tooling systems. Contact Metav Werkzeuge for tailored advice on Teknik Makina grooving clamp holders and to confirm availability from the Emmerich warehouse Technical data SKU: D607TM Manufacturer: Teknik Makina Article name: Grooving clamp holder (Stechklemmhalter) ECLASS: 21181005 Core technical data Shank height: 12 mm Shank width: 12 mm Cutting width: 2 mm Max plunge depth: 16 mm Overall length: 125 mm Weight: 0.161 kg Special features Left-hand cutting direction Compatible with Korloy 2C MGM inserts ISO designation: 1212 Bar designation: 2C-L MGM FAQ Which inserts fit this grooving holder? The grooving clamp holder (Stechklemmhalter) is compatible with Korloy 2C MGM indexable inserts as indicated in the product data. Is the cutting direction left-hand or right-hand? The holder is specified for left-hand cutting direction and should be used accordingly in lathe setups. What are the main dimensions to check for toolpost mounting? Key dimensions include the 12 x 12 mm shank height and width and an overall length of 125 mm, which determine compatibility with the toolpost or turret. What is the maximum plunge depth for grooving operations? The maximum plunge depth specified for this holder is 16 mm, defining the practical limit for parting-in operations. Is the ISO designation provided for reference? Yes — the holder’s ISO designation is listed as 1212, which aids selection and matching with corresponding insert geometries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑matched holder that combines slim 12 x 12 mm shank geometry and a 125 mm overall length for straightforward integration into existing turning fixtures; its compatibility with DGN 3C inserts from ISCAR ensures quick tool changes and consistent groove width control. Order via Metav Werkzeuge or consult our specialists for application advice. DGN parting and grooving tool holder – Teknik Makina (D021TM) with 12 x 12 mm shank, 3 mm cutting width A DGN parting and grooving tool holder engineered for precise parting and grooving in lathe operations, designed to accept DGN 3C inserts and to fit ISO‑1212 shank interfaces 12 x 12 mm ISO shank profile Compatible with DGN 3C inserts from ISCAR 3 mm cutting width for narrow grooves M4x10 clamping screw with T15 key Precision and repeatability for turning processes The holder delivers a defined shank geometry with an ISO 1212 (12 x 12 mm) profile, providing stable seating in standard toolposts and ensuring repeatable positioning. This stability reduces vibration during parting operations, which in turn lowers the risk of chip entanglement and tool breakage. The slim 12 mm body and a 12.3 mm cutting‑head width allow close approach to the workpiece while the 3 mm cutting width gives consistent groove dimensions; these characteristics make the component suitable for series production where dimensional repeatability is required. Fast insert changes and secure clamping Clamping is accomplished via an M4x10 hex screw, driven with a T15 key, enabling rapid insert replacement and secure fixation of the indexable plate. The holder is intended for DGN 3C indexable inserts (manufacturer: ISCAR), so inventory management benefits from standardised insert formats. The low mass (0.13 kg) and a 125 mm overall length permit agile handling and straightforward mounting, supporting short setup times and efficient tool changes on the shop floor. Integration, versatility and application guidance With a maximum parting depth of 12 mm the tool is suited to typical grooving and parting operations on turned parts. The product has been designed for compatibility with common lathe tool posts and clamping systems that accept the 1212 designation, simplifying retrofitting into existing workflows. For complex geometries or unusual materials, technical guidance is available to determine the optimal cutting parameters and insert grades; this supports reliable results across small‑batch or high‑volume production runs. Discuss application details with Metav Werkzeuge to confirm fitment and optimise cutting parameters for specific materials and cycle times Technical Data Article number: D021TM Manufacturer: Teknik Makina Designation: Stechklemmhalter / DGN SKU: D021TM Compatible inserts: DGN 3C (ISCAR) Facts Shank width: 12 mm Shank height: 12 mm Cutting‑head width: 12.3 mm Cutting width: 3 mm Maximum parting depth: 12 mm Overall height: 12 mm Overall length: 125 mm Weight: 0.13 kg Clamping screw: M4x10 Hex key size: T15 ISO designation: 1212 Special features Designed for DGN 3C indexable inserts Compatible with ISCAR insert geometries Low mass for reduced toolpost load Standardised ISO shank for easy retrofit FAQ What inserts fit this tool holder? The holder accepts DGN 3C indexable inserts; it is specified for inserts from ISCAR and compatible geometries. What are the shank dimensions and ISO code? The shank is 12 x 12 mm, corresponding to the ISO 1212 designation for standard toolpost fitting. How deep can the holder cut or part? The maximum parting depth is 12 mm, suitable for standard grooving and parting tasks. Which screw and key are required for clamping? Clamping is with an M4x10 hex screw and requires a T15 key for secure fixation of the insert. Is the tool suitable for quick production changeovers? Yes; the low weight and standardised insert compatibility support rapid insert changes and short setup times. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com