Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of robust construction, precise 90° shoulder geometry and integrated coolant for reliable cycle times; order the component directly through Metav Werkzeuge or consult our sales engineers for application advice. Corner tool head (Eckmesserkopf) — 100 mm diameter, internal coolant, Teknik Makina A Corner tool head for XEKT 1904 indexable inserts, engineered for 90° shoulder machining and equipped with internal coolant for improved tool life. 100 mm diameter, 90° cutting angle Internal through-coolant system Compatible with XEKT 1904 Korloy inserts Total length 63 mm, robust mass Improved cycle times for shoulder machining The compact indexable head delivers a consistent 90° cutting geometry that reduces set-up time and simplifies programme calculation. The 100 mm diameter and solid construction provide stability during interrupted cuts, while the six available cutting edges provide extended on-machine life. For production environments where repeatability and throughput matter, this insert carrier translates to fewer tool changes and more productive spindle hours. The design is suitable for a wide range of turning and profiling operations where a defined shoulder needs to be produced quickly and accurately. Controlled coolant flow to extend insert life Integrated internal coolant directs cutting fluid straight to the cutting zone, flushing away chips and reducing heat at the edge. This targeted cooling lowers flank wear and supports more consistent cutting forces, which in turn helps maintain dimensional accuracy across batches. When paired with XEKT 1904 indexable inserts from Korloy, the coolant feed improves chip control and reduces the risk of built-up edge, making longer feed rates and higher metal removal possible without sacrificing surface finish. Practical fastening and serviceability for workshop efficiency Fastening uses a T15 Torx drive and M4x8.5 screw for secure, repeatable clamping of the insert seat, allowing quick index changes and minimal downtime. The tool head’s total length of 63 mm and weight of 1.952 kg give a low centre of gravity for stable tool engagement in heavier cuts. Clear mechanical interfaces and widely available Torx tooling mean maintenance is straightforward, and stock levels can be managed without bespoke parts. These practical details reduce assembly complexity and help standardise tooling across the workshop. For tailored application guidance and to secure supply, contact Metav Werkzeuge in Emmerich — info@metav-werkzeuge.com or call +49 2822 7131930 for direct ordering and technical consultation on the Teknik Makina corner tool head (SKU T369TM) Technical data Article number: T369TM ECLASS: 21181015 Product type: Corner tool head Label: 100mm corner tool head XEKT 1904 L63mm with internal coolant Manufacturer: Teknik Makina Facts Diameter: 100 mm Total length: 63 mm Weight: 1.952 kg Cutting edges: 6 Cutting angle: 90° Torx key: T15 Torx screw: M4x8.5 Special features Internal coolant: yes Compatible with XEKT 1904 indexable inserts Compatible insert manufacturer: Korloy Application: 90° shoulder/face machining FAQ Which inserts fit this tool head? The corner tool head is designed for XEKT 1904 indexable inserts and is compatible with Korloy-manufactured XEKT 1904 inserts; the SKU is T369TM. Does the tool head provide internal coolant? Yes, the tool head features an internal through-coolant feed that delivers lubricant directly to the cutting edge for improved tool life and chip control. What is the cutting geometry and typical use case? The head provides a 90° cutting angle suited to shoulder and face turning where square shoulders and accurate axially aligned faces are required. How is the insert secured and serviced? Inserts are secured with an M4x8.5 screw using a T15 Torx drive, enabling rapid index changes and straightforward workshop maintenance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact turning head that combines stable cutting performance with straightforward maintenance: the design delivers consistent seating for SPMT 1204 indexable inserts and a large Ø100 mm head for improved rigidity, while the 32 mm shank enables secure toolholder integration — order the component directly via Metav Werkzeuge or request specialist guidance from our consultants. Corner turning head T653TM – Indexable insert turning head, Ø100 mm, for SPMT 1204 (Teknik Makina) A robust Corner turning head engineered for turning applications with SPMT 1204 indexable inserts, providing a compact solution for stable cutting and frequent indexing Compatible with SPMT 1204 indexable inserts 100 mm head diameter for stable cutting 32 mm shank for secure toolholder fit Eight cutting edges for extended use Consistent cutting stability that reduces downtime The Corner turning head T653TM is designed to sustain precise tool contact throughout each cut. The Ø100 mm head diameter increases the moment of inertia at the cutting zone, which reduces vibration and supports a steady machining process. With 8 cutting edges, the holder enables multiple index operations on a single insert, lowering replacement frequency and cutting overall tooling costs while improving uptime in batch and serial production. Secure clamping and repeatable seating for reliable cycles A engineered clamping solution gives repeatable seating: the tool accepts a 32 mm shank for rigid mounting in standard toolholders and is fastened with a Torx M5x12 screw driven by a T20 key for reliable tightening without cam‑out. The result is a stable interface that minimises micro‑movement at the insert seat, translating into consistent surface quality and longer insert life for repetitive turning tasks. Compact geometry that supports efficient toolchanges With an overall length of 50 mm, the head occupies minimal axial space while still providing the required clearance for organised tooling setups. The compatibility with indexable inserts such as SPMT 1204 means insert changes are quick and do not require regrinding, which helps workshops maintain throughput and reduce operator time spent on tool maintenance. This compact, indexable approach supports both short runs and larger production series. Practical integration into machining centres and workshops The T653TM is suitable for industrial turning operations where tool stability and fast indexability are priorities. At a weight of 1.786 kg the head contributes to a solid tool assembly that assists in dampening cutting forces. Supplied components and fasteners follow common workshop standards, enabling straightforward inventory management and interchangeability across compatible holders from the same tool family. For reliable integration of Teknik Makina components such as the T653TM corner turning head, contact Metav Werkzeuge for tailored supply and technical advice from Emmerich. Technical data Article number: T653TM Manufacturer: Teknik Makina Suitable for indexable inserts: SPMT 1204 Dimensions & weight Head diameter: 100 mm Shank diameter: 32 mm Overall length: 50 mm Weight: 1.786 kg Cutting edges: 8 Assembly & fastening Torx screw: M5x12 Torx key size: T20 For SPMT 1204 indexable inserts FAQ Which indexable inserts fit this turning head? The corner turning head T653TM is compatible with SPMT 1204 indexable inserts, designed for simple indexing and reliable seating in turning operations. What shank diameter is required for mounting? A 32 mm shank is required for correct mounting of the T653TM; the diameter ensures a stable connection with standard toolholders. How many usable cutting edges are available before replacement? The holder supports 8 cutting edges, enabling multiple index positions per insert and reducing the frequency of full insert replacements. Which screw and key are used for insert clamping? Clamping is performed with a Torx M5x12 screw and requires a T20 key for secure tightening and repeatable seating. Is this head suitable for industrial machine tools? Yes; the T653TM is intended for industrial turning applications where indexable inserts and a compact, rigid tool holder improve productivity and repeatability. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid tool head that combines compatibility with TPKN 1603–2204 indexable inserts and a 90° cutting angle for reliable shoulder turning — order directly via Metav Werkzeuge or consult our specialists for application guidance. Corner tool head T130TM — indexable head for TPKN 1603–2204, 90° cutting angle (Teknik Makina) Corner tool head T130TM for precision turning and facing, designed to accept TPKN 1603–2204 indexable inserts and deliver consistent square-shoulder results on standard toolposts Compatible with TPKN 2204 inserts 90° cutting angle for square shoulders 32 mm shank diameter for secure clamping M8x24 hex screw, requires 5 mm Allen key Stable mounting for predictable machining outcomes A robust construction and a 32 mm shank ensure the holder remains rigid under load, which reduces vibration and improves finish quality. The head’s 100 mm diameter and mass of 1.398 kg provide mechanical stability for interrupted cuts and finish turning alike. The 90° cutting angle is optimised for producing square shoulders with minimal tool deflection, helping to maintain dimensional accuracy across production runs and extending insert life through reduced chatter. Faster index changes and fewer setup steps Compatibility with TPKN 1603–2204 indexable inserts simplifies insert standardisation across a workshop and shortens changeover times. Fixing is achieved with an M8x24 screw secured by a 5 mm Allen key, enabling quick, repeatable clamping without specialised fixtures. Clear mechanical engagement and a simple fastening arrangement reduce the risk of incorrect seating, which means less rework and a more efficient process flow on the shop floor. Compact design that integrates into existing workflows With an overall length of 52 mm and a head configured for up to five cutting positions, the tool head supports versatile orientations in confined toolpost spaces while maintaining cutting performance. The combination of compactness and mechanical mass yields predictable cutting forces, so cycle times can be kept consistent without sacrificing surface quality. This design is suitable for production and jobbing environments where space, repeatability and uptime are priorities, supporting stable, long-term operation. Contact Metav Werkzeuge for tailored application advice or a specification check for the Teknik Makina corner tool head T130TM — our specialists in Emmerich can confirm suitability for specific machining tasks and assist with integration into existing toolholding systems. Technical data Article number: T130TM Manufacturer: Teknik Makina Designation: Corner tool head (Eckmesserkopf) for TPKN 1603–2204 indexable inserts SKU: T130TM Facts Weight: 1.398 kg Head diameter: 100 mm Overall length: 52 mm Shank diameter / clamping diameter: 32 mm Number of cutting positions: 5 Cutting angle: 90° Special features Compatibility: TPKN 1603–2204 indexable inserts Fastening: M8x24 hex screw Required tool: 5 mm Allen key Suitable for shoulder turning and facing operations FAQ Which inserts fit this corner tool head? The corner tool head T130TM is specified for use with TPKN 1603–2204 indexable inserts and supports the insert geometries listed for that designation. What is the required clamping interface? Mounting uses a 32 mm shank; the fixing screw is M8x24, tightened with a 5 mm Allen key for secure clamping. Is the unit suitable for square-shoulder machining? Yes, the 90° cutting angle and rigid head construction make the T130TM appropriate for producing square shoulders with repeatable accuracy. How many index positions are available on the head? The head offers five cutting positions, allowing multiple index turns of the insert before replacement is required. Can the tool head be integrated into existing toolposts? Integration is straightforward where a 32 mm shank interface is supported; ensure correct clamping and alignment when fitting the T130TM to preserve accuracy. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, 90° cutting-angle head that accepts WNGX 0806 indexable inserts and a stout 32 mm shank for improved rigidity; combine precise shoulder turning and reliable clamping with fast insert changes — order via Metav Werkzeuge or consult our specialists for application advice. Corner tool head (Eckmesserkopf) by Teknik Makina — 90° cutting angle, for WNGX 0806 indexable inserts Corner tool head (Eckmesserkopf) designed for right-angle turning and shoulder work on CNC lathes, compatible with WNGX 0806 indexable inserts and built for repeatable set-ups Suitable for WNGX 0806 indexable inserts 90° cutting angle for precise shoulder turning 32 mm shank diameter for high rigidity Torx fastening M5x12 with T20 key Consistent shoulder quality from the 90° geometry The 90° cutting angle provides a defined contact geometry that helps produce repeatable shoulders and faces with minimal re‑work. Using a right‑angle head designed for the WNGX family ensures the insert edge engages material squarely, which reduces lateral tool movement and improves dimensional stability. For production runs where consistent shoulder finish matters, the controlled geometry contributes directly to cycle‑time predictability and fewer scrapped parts. The compact form and clear edge orientation make toolpath programming and set‑up verification straightforward on standard CNC turning centres. Robust construction that reduces vibration and downtime A 32 mm shank combined with a 100 mm diameter head and an overall length of 52 mm delivers a compact, rigid assembly that resists chatter during heavy cuts or interrupted operations. The solid mass (weight 1.58 kg) stabilises the toolholder on the turret, improving surface finish and prolonging insert life. Fast, reliable clamping is achieved via an M5x12 Torx screw secured with a T20 key; this straightforward fixation reduces maintenance time and supports quick insert replacement during shift changes. The result is a durable turning solution geared to maintain throughput in small and medium series production. Compatibility, serviceability and shop‑floor benefits Engineered for WNGX 0806 indexable inserts and compatible with Korloy supply, the head simplifies tooling logistics for workshops standardising on that insert family. The Torx‑type fastening facilitates repeatable torque application and secure clamping, while the architecture supports up to 8 cutting edges, enabling economical use of insert geometry where applicable. For machinists, the assembly means fewer different holders to manage, quicker set‑ups and reduced tool change frequency — practical advantages that help maintain uptime and predictable production flow. Choose Teknik Makina quality through Metav Werkzeuge: request tailored application guidance or a procurement proposal referencing SKU T778TM and secure the right tool for consistent, industrial turning tasks Technical Data Article number: T778TM Manufacturer: Teknik Makina Product name: Corner tool head (Eckmesserkopf) for WNGX 0806 indexable inserts Fastening screw: M5x12 Torx Torx key size: T20 Facts Diameter: 100 mm Shank diameter (D): 32 mm Overall length: 52 mm Weight: 1.58 kg Cutting angle: 90° Number of cutting edges: 8 Special features For WNGX 0806 indexable inserts Compatible with Korloy inserts Torx fastening for repeatable clamping Compact design for CNC turning centres Brand: Teknik Makina FAQ Which inserts are compatible with this tool head? The corner tool head accepts WNGX 0806 indexable inserts; the design is compatible with Korloy‑specification inserts for that size. How is the insert secured in the holder? Insert clamping is achieved via an M5x12 Torx screw, tightened using a T20 key to ensure repeatable clamp force and secure seating. Is the tool head suitable for heavy cutting or interrupted cuts? The compact geometry, 32 mm shank and mass (approx. 1.58 kg) provide rigidity suited to demanding turning jobs, helping to reduce vibration during heavier or interrupted cuts. What are the main dimensional features to verify on the machine turret? Check the shank diameter (32 mm) and overall length (52 mm) to ensure correct turret fit and adequate clearance for the 100 mm head diameter. Can the tool head be used for precise shoulder facing? Yes, the 90° cutting angle is intended to produce consistent shoulders and faces, supporting precise finishing routines on the lathe. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a solid combination of precise 90° geometry and stable 32 mm mounting for consistent shoulder turning and repeatable results; the robust design with Torx M4x11 fastening supports safe clamping and simple maintenance. Order the tool through Metav Werkzeuge or consult our specialists for application-specific setup. Corner tool head T428TM – 90° holder for R390-1806 indexable inserts by Teknik Makina The Corner tool head T428TM is a compact 90° toolholder engineered for shoulder turning and profiling with R390-1806 indexable inserts, suited to medium-duty lathe work and workshop environments 90° cutting angle for precise corner cuts Compatible with R390-1806 Sandvik inserts 32 mm shank diameter for stable mounting Torx M4x11 fastening, T15 key Consistent shoulder turning through rigid mounting The design delivers stable clamping and repeatable results by combining a 32 mm shank with a robust body and secure Torx fastening. This rigid interface reduces vibration and improves surface finish when performing shoulder and face-turning operations, so cycle-time variations are minimised and tool life becomes more predictable. The specification includes a 100 mm diameter reference and an overall length of 52 mm, which contributes to compact tool overhang and better control of cutting forces. Easy integration with common indexable inserts for efficiency Compatibility with R390-1806 indexable inserts from Sandvik allows straightforward tool management and inventory alignment across shops that already use this insert family. The holder accommodates the standard insert geometry and is secured with an M4x11 Torx screw (T15), enabling fast insert changes and low downtime. With seven cutting edges specified on the head, the component is optimised for multi-edge engagement patterns that maintain cutting stability in interrupted cuts and profiling tasks. Measurable benefits for workshop productivity Engineered for reliable everyday use, the component is specified with a weight of 1.595 kg, providing enough mass to dampen chatter without excessive load on the turret. The 90° cutting angle simplifies setup for shoulder operations and reduces the need for secondary finishing passes, improving throughput. Where process reproducibility and predictable tool behaviour are priorities, this toolholder is designed to be integrated into standard toolkits and CNC turret systems without lengthy adaptation. For robust 90° shoulder turning and dependable insert compatibility, contact Metav Werkzeuge to discuss Teknik Makina's T428TM and ensure fast supply from our Emmerich stock — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T428TM Manufacturer: Teknik Cutting Tools Compatible inserts: R390-1806 Facts Diameter: 100 mm Shank diameter: 32 mm Overall length: 52 mm Weight: 1.595 kg Cutting angle: 90° Cutting edges: 7 Special features Torx screw M4x11 Torx key size T15 For R390-1806 indexable inserts Compatible with Sandvik insert range FAQ What insert type does this holder accept? The holder is specified for R390-1806 indexable inserts and is compatible with the Sandvik insert family named for that designation. Is the tool suitable for shoulder turning on a CNC lathe? Yes, the T428TM corner tool head is designed with a 90° cutting angle and a 32 mm shank to provide the rigidity required for reliable shoulder turning on turret-equipped lathes. Which fastening and key size are required to secure inserts? Insert clamping is achieved with a Torx M4x11 screw; the corresponding key size is T15, ensuring secure and repeatable fastening. How does the toolholder improve surface finish and tool life? The combination of a compact overall length, 32 mm mounting diameter and robust construction reduces vibration and tool deflection, which improves surface finish and supports longer insert life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 90° cutting angle and a sturdy 32 mm shank for repeatable, high-stability turning operations; the compact 52 mm overall length keeps set-up simple while the SECO-compatible insert interface reduces tooling changes. Order the Angle turning head directly via Metav Werkzeuge or contact their consultants for integration advice. Angle turning head T525TM — 90° cutting angle, 32 mm shank (Teknik Makina) The Angle turning head T525TM is a right-angle indexable insert holder designed for turning and facing operations with XOMX 1806 indexable inserts, combining rigid mounting and standardised fastening for reliable daily use. 90° cutting angle for accurate facing 32 mm shank for stable clamping Compatible with XOMX 1806 inserts by SECO Robust Ø100 mm body, 8 cutting edges Precision and compatibility for consistent turning The 90° cutting angle and indexable insert interface deliver predictable cutting geometry that supports consistent surface finish and dimensional control across batches. Fitted for XOMX 1806 indexable inserts, the head accepts industry-standard carbide plates (SECO-compatible), which simplifies procurement and keeps changeover times low. For less technical readers: an indexable insert is a reversible carbide plate that locates into the holder so that a worn edge can be rotated or replaced quickly—this reduces downtime and maintains cutting performance without regrinding the tool. Secure clamping with straightforward serviceability A substantial 32 mm shank and a body diameter of Ø100 mm provide the rigidity needed for heavy contact forces during facing or shoulder turning. Fastening is by an M4.5x11 Torx screw secured with a T15 key, a common standard that ensures repeatable clamping torque and simple maintenance procedures. The combination of solid mounting and a compact 52 mm overall length keeps the tool close to the toolpost, reducing deflection. The item’s mass of 1.661 kg contributes to vibration damping, which supports longer insert life and steadier surface results. Designed to streamline workshop workflows The head’s accommodation for XOMX 1806 inserts and its SECO compatibility mean fewer special parts in stock and straightforward replacement logistics. The configuration with eight cutting edges on the assembly reduces frequency of full-tool exchanges, while the compact footprint supports machines with limited turret clearance. A clear classification code (ECLASS 21181015) aids purchasing and inventory systems. If there is uncertainty about machine fitment or insert grade selection, Metav Werkzeuge can advise on the optimal insert geometry and clamping sequence for the intended application. For tailored technical advice on integrating the Teknik Makina angle turning head T525TM into existing tool systems, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930. Technical data SKU: T525TM Manufacturer: Teknik Makina Product designation: Angle turning head (Eckmesserkopf) Compatible inserts: XOMX 1806 Compatible insert manufacturer: SECO ECLASS: 21181015 Facts Shank diameter: 32 mm Body diameter: Ø100 mm Cutting angle: 90° Number of cutting edges: 8 Overall length: 52 mm Weight: 1.661 kg Torx screw: M4.5x11 Torx key size: T15 Special features 90° cutting geometry SECO-compatible indexable insert interface Designed for XOMX 1806 indexable inserts Files available: 62de7ef933927e49dbf327a1, 62de7e74a9cff922f4703d37 FAQ Which insert type is required for this head? The head is designed for XOMX 1806 indexable inserts; it is compatible with SECO variants that match the XOMX 1806 geometry. What shank diameter and mounting are used? Mounting uses a 32 mm shank; the compact 52 mm overall length keeps the turning head close to the toolpost for improved rigidity. Is the cutting angle suitable for facing and shoulder work? The 90° cutting angle makes the head well suited to facing and square shoulder turning, providing a true right-angle cutting geometry. What fastening hardware is required for insert clamping? Insert and head fastening uses an M4.5x11 Torx screw, tightened with a T15 key for secure and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a rigid 100 mm construction, integrated internal coolant and broad compatibility with ADKT 1505 indexable inserts for reliable 90° profiling and reduced downtime. Order or request application advice directly via Metav Werkzeuge if additional machining data is required. Eckmesserkopf – 100 mm corner tool head with internal coolant (Teknik Makina) A Eckmesserkopf for ADKT 1505 indexable inserts, engineered for square-edge turning and profiling with built-in coolant supply to support stable production. 100 mm diameter for robust cutting Internal coolant for improved chip evacuation Compatible with ADKT 1505 inserts (ISCAR) Eight cutting positions, 90° cutting angle Increased process stability through rigid design and coolant delivery The robust 100 mm body reduces deflection during heavy profiling, delivering a steady cutting geometry and predictable tool life. Built-in internal coolant directs lubricant and coolant close to the cutting edge, which lowers thermal load, improves chip control and prolongs insert performance. These factors translate into fewer tool changes and consistent batch tolerances, making the head well suited to production environments where repeatability and cycle-time savings matter. The combination of rigidity and targeted cooling supports higher material removal rates without compromising surface finish. Quick set-up and secure clamping for uptime optimisation Set-up is straightforward: the clamping uses a Torx T15 drive and M4 x 10 fastening screws for secure insert retention and repeatable seating. The toolholder’s eight cutting positions mean multiple indexable lives per insert arrangement, reducing machine downtime for insert changes. Engineers benefit from a clear service routine: fast access to screws and a compact overall length of 52 mm allow confined [workpiece-to-tool] layouts to be addressed without complex reprogramming. The compact mass (approx 1.546 kg) balances rigidity with manageability during tool changes and tool magazine loading. Broad compatibility and application-focused advantages Compatibility with ADKT 1505 inserts and proven suitability for inserts from ISCAR simplifies purchasing and stocking decisions, as common insert geometries and grades can be used. A true 90° cutting angle supports square shoulder machining and clean-face transitions, reducing secondary finishing operations. Where consistent edge definition and rapid chip evacuation are required — for example, in medium- to high-volume turning and profiling tasks — this indexable head offers a pragmatic route to higher productivity while keeping inventory and set-up complexity low. The toolholder body ensures predictable results across repeated cycles and diverse batch sizes. Contact Metav Werkzeuge for tailored application advice and supply of the Teknik Makina corner tool head with internal coolant; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: T207-1TM Article: Eckmesserkopf for ADKT 1505 Indexable Inserts Manufacturer: Teknik Makina ECLASS: 21181015 Core specifications Diameter: 100 mm Total length: 52 mm Weight: 1.546 kg Cutting angle: 90° Cutting positions: 8 Torx key: T15 Torx screw: M4 x 10 Special features Internal coolant Compatible with ADKT 1505 indexable inserts Compatible insert manufacturer: ISCAR Suitable for square-edge turning and profiling FAQ Which insert type fits this head? The head accepts ADKT 1505 indexable inserts; it is designed for common ADKT geometries and compatible with inserts from ISCAR. Is the cooling internal or external? Internal coolant is integrated into the head to deliver fluid directly to the cutting zone, enhancing chip control and insert life. How many cutting positions are available before regrinding or replacement? The design provides eight cutting positions, enabling multiple indexings and extended service intervals before insert replacement. What is the recommended fastening method for the inserts? Inserts are secured using the supplied M4 x 10 fastenings with a Torx T15 driver to ensure repeatable clamping and stable seating. Can this head produce true 90° shoulders? Yes, the 90° cutting angle is intended for square-shoulder turning and clean-face transitions, reducing secondary finishing needs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the stable 100 mm diameter and built‑in coolant to boost throughput while reducing insert wear; reliable compatibility with ADKT 1706 Korloy inserts ensures straightforward integration into existing turning stations — order or request advice via Metav Werkzeuge for fast supply and technical guidance. Corner tool head for ADKT 1706 indexable inserts — 100 mm diameter, internal coolant (Teknik Makina) A corner tool head for ADKT 1706 indexable inserts designed for robust turning operations and reliable coolant delivery in workshop and production settings. 100 mm diameter for stable machining Internal coolant for optimised chip evacuation Compatible with ADKT 1706 Korloy inserts 8 cutting edges, 90° cutting angle Optimised stability and chip control for higher productivity The compact turning head delivers consistent performance through its 100 mm diameter and compact 63 mm overall length, balancing rigidity with accessibility at the toolpost. Thanks to the 8 cutting edges, the geometry distributes cutting forces to reduce vibration and maintain surface quality; the 90° cutting angle provides predictable engagement for shoulder and facing operations. This results in fewer reworks and a more reliable production rhythm, especially on medium‑ to heavy‑duty turning tasks. Coolant-fed design that extends insert life and improves finish Integrated internal coolant directs lubricant precisely to the cutting zone, lowering cutting temperatures and flushing chips away from the insert rake. The focused coolant supply extends the life of ADKT 1706 inserts and helps secure consistent part finish across longer runs. Compatibility with Korloy inserts and standard fastening using a T15 Torx drive and M4x10 screws simplifies maintenance and insert changes, reducing machine downtime and tooling complexity on the shop floor. Simple integration and serviceable construction for production use Installation and service follow standard workshop procedures: the head’s footprint and mounting dimensions suit common toolholders, while the modest 1.76 kg mass keeps loading predictable during indexing and tool changes. Fasteners with T15 interface ensure repeatable clamping torque and secure seat for each insert, supporting stable cutting conditions. The design prioritises ease of replacement and inventory harmonisation, enabling maintenance teams to manage fewer part numbers without compromising cutting performance. For procurement or technical clarification on the Teknik Cutting Tools corner tool head with internal coolant, contact Metav Werkzeuge for expert advice and reliable supply from Emmerich. Technical data Article number: T592-2TM Label: 100mm Eckmesserkopf ADKT 1706 L63mm mit Innenkühlung Product type: Corner tool head Manufacturer: Teknik Makina Facts Diameter: 100 mm Overall length: 63 mm Weight: 1.76 kg Cutting edges: 8 Cutting angle: 90° Internal coolant: yes Torx key: T15 Torx screw: M4x10 ECLASS: 21181015 Special features Compatible with ADKT 1706 indexable inserts Suited for Korloy insert range Compact construction for tight toolpost clearances Designed for predictable clamping and easy insert changes FAQ Is this head compatible with standard ADKT 1706 inserts? Yes. The corner tool head is designed for use with ADKT 1706 indexable inserts and specifically accommodates Korloy‑specification inserts. Does the tool head support internal coolant lines? Yes. The integrated internal coolant feature channels fluid to the cutting zone to improve tool life and surface finish. Which fastening tools are required for insert changes? Insert and clamp screws use a T15 Torx interface and M4x10 screws for secure, repeatable clamping during maintenance. What advantages does the 100 mm diameter provide? A 100 mm diameter increases rigidity at the cutting edge, improving stability and enabling more consistent surface quality in turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise 90° cutting geometry, stable Ø100 mm head engagement and straightforward mounting with a 32 mm shank for reliable shoulder turning and profiling. Order the component via Metav Werkzeuge or consult their specialists for application advice and fast supply. Corner tool head T448TM — 90° corner turning head, Ø100 mm, for ANKX 0706 indexable inserts (Teknik Makina) Corner tool head T448TM designed for right‑angle shoulder turning and external profiling with indexable inserts in industrial turning operations 90° cutting angle for precise shoulder turning Ø100 mm head diameter for stable engagement Compatible with ANKX 0706 indexable inserts 32 mm tool holder shank for secure mounting Torx M5x12 screw, T20 key specification Reliable shoulder and profile turning with defined geometry The Corner tool head T448TM brings a 90° cutting angle that is specifically suited to accurate shoulder and profile operations. The combination of a Ø100 mm head and 7 cutting edges ensures consistent contact and repeatable results when used with compatible turning inserts. This geometry reduces the need for manual rework, improving process predictability and supporting repeatable part quality in serial production. Fast, consistent mounting and insert compatibility Mounting is straightforward thanks to the 32 mm shank and the defined fastener specification (M5x12 Torx screw, T20 key). The head accepts ANKX 0706 indexable inserts and is noted as compatible with ISCAR insert types, enabling quick replacement and standardised tool setups. Reduced changeover complexity translates to shorter downtime and simpler tool inventory management on the shop floor. Built for stable engagement and vibration damping At a mass of 2.029 kg, the turning head provides inherent stability that helps dampen vibration during cutting, which in turn benefits surface finish and tool life. The robust construction contributes to consistent cutting conditions across batches, so machines and operators can maintain steady feed rates and achieve predictable machining performance with fewer process interruptions. Practical application and workshop integration Designed for external turning, shoulder machining and contour work, the head integrates with conventional lathe tool posts that accept a 32 mm holder. The use of standardised indexable inserts keeps consumables familiar across operations, simplifying procurement and lowering the learning curve for operators. When planning tool layouts, consider the 90° geometry for operations where square shoulders and precise transitions are required. Select the Teknik Makina T448TM corner tool head for dependable shoulder turning — contact Metav Werkzeuge in Emmerich for application guidance and swift supply at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T448TM Manufacturer: Teknik Makina Product name: Corner tool head (Eckmesserkopf) Description: for ANKX 0706 indexable inserts Core specifications Diameter: 100 mm Shank diameter: 32 mm Total length: 52 mm Weight: 2.029 kg Cutting angle: 90° Number of cutting edges: 7 Features Compatible with ANKX 0706 indexable inserts Suitable for ISCAR insert types Torx screw: M5x12 Torx key specification: T20 FAQ Which indexable inserts fit this turning head? The turning head accepts ANKX 0706 indexable inserts; compatibility with ISCAR insert types is indicated for the Corner tool head T448TM. What fixing hardware is specified for mounting? Mounting and clamping use a Torx M5x12 screw with a T20 Torx key, specified for the T448TM to secure the insert head reliably. What is the benefit of the 90° cutting angle? A 90° cutting angle enables precise shoulder formation and square transitions, making the head suitable for accurate external profiling and shoulder turning with consistent tolerances. Is the shank size standardised for typical lathe tool posts? Yes — the 32 mm shank diameter is a common holder size, allowing the Corner tool head T448TM to be mounted in tool posts designed for 32 mm tool holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining the 100 mm diameter body with internal coolant and compatibility with AP--1604 indexable inserts delivers stable cutting and efficient chip control; order via Metav Werkzeuge or consult their technical advisors for application support. Corner tool head for AP--1604 indexable inserts — 100 mm diameter, internal coolant (Teknik Makina) Corner tool head for AP--1604 indexable inserts is a compact machining head designed for precision turning and facing operations where coolant-fed cutting and repeatable set-ups are required. 100 mm diameter for stable cutting Internal coolant for improved chip evacuation Fits AP--1604 indexable inserts (Korloy) 52 mm overall length for compact set-ups Seven cutting edges, 90° cutting angle Greater process stability with coolant-fed cutting The robust 100 mm body provides increased rigidity which reduces chatter in interrupted and finishing cuts. With internal coolant directed to the cutting zone, thermal loads are lowered and tool life is extended through improved lubrication and chip removal. This translates into steadier surface finishes and fewer reworks in batch production. The design supports industrial machining routines where consistency and predictable tool wear are priorities. Fast, reproducible insert changes for efficient shopfloor flow A straightforward clamping and fastening arrangement, secured with a Torx T15 key and M4x10 screw, enables quick insert replacement and consistent positional accuracy after each change. The presence of seven cutting edges gives a defined balance between usable edge count and accessibility for indexable inserts, reducing downtime for regrinds and replacements. Clear torque engagement and standard fasteners speed up maintenance and help standardise tool-change procedures across multiple lathes. Compact geometry that fits tight set-ups and 90° operations With an overall length of 52 mm the head suits compact toolholders and restricted overhangs, lowering bending moments and improving repeatability. The 90° cutting angle is ideal for facing and shoulder work where perpendicular engagement is needed, enabling square shoulders without complex tool paths. The moderate mass of the component contributes to stable cutting dynamics while remaining manageable for quick toolholder swaps. Compatibility and integration into existing tooling systems Engineered for use with AP--1604 indexable inserts and compatible with inserts from Korloy, the head is suitable for a wide range of workshop applications that rely on industry-standard insert geometries. The component, supplied under SKU T188-1TM, is built to integrate into conventional lathe tool posts and holder systems and is intended for users seeking a reliable, coolant-fed corner solution without bespoke adaptations. Contact Metav Werkzeuge for application advice on Teknik Makina's T188-1TM corner tool head or to request cutting data and availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: T188-1TM Product type: Corner tool head Manufacturer: Teknik Makina ECLASS: 21181015 Label: 100mm Eckmesserkopf AP-- 1604 L52mm mit Innenkühlung Specifications Diameter: 100 mm Overall length: 52 mm Weight: 1.057 kg Number of cutting edges: 7 Cutting angle: 90° Design and features Internal coolant: yes For indexable inserts: AP--1604 Compatible insert manufacturer: Korloy Fastening: Torx T15 Torx screw: M4x10 FAQ What insert type is required for this head? The head accepts AP--1604 indexable inserts; inserts from Korloy are listed as compatible with this machining head (SKU T188-1TM). Does the tool head provide coolant supply to the cutting edge? Yes, the component is equipped with internal coolant to feed the cutting zone and support heat control and chip evacuation. What is the overall length and how does that affect set-up? The overall length is 52 mm, which supports compact toolholder arrangements and reduces overhang, improving rigidity and repeatability. Which fasteners and key are used for insert clamping? Insert clamping is secured with a Torx T15 engagement and an M4x10 screw to ensure reproducible positioning and straightforward maintenance. Which cutting applications are best suited to the 90° angle? The 90° cutting angle is particularly suitable for facing and shoulder operations where perpendicular engagement and square corner transitions are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise 90° cutting geometry, secure 32 mm shank fixation, and straightforward maintenance for consistent corner turning and minimal tool-change downtime — order directly via Metav Werkzeuge or ask our consultants for application advice. Corner tool head for APKT 1604 indexable inserts (T189TM) — 90° cutting geometry, 32 mm shank The corner tool head is a 90° turning head designed for use in CNC lathe operations with APKT 1604 indexable inserts, offering rigid clamping and compatibility with common insert manufacturers for reliable corner machining. 90° cutting geometry for accurate corners 32 mm shank for secure toolholder fit Compatible with APKT 1604 indexable inserts M4x10 Torx clamping screw; T15 key Consistent corner machining that improves part quality The 90° cutting geometry delivers a predictable cutting direction that helps to reduce deflection and maintain consistent edge form across serial parts. The head’s rigid construction and defined cutting angle translate into repeatable results on turned profiles, particularly where precise shoulder and corner transitions are required. For operations that demand regular high-quality finishes, the defined geometry simplifies process control and reduces the need for corrective grinding. Secure clamping and straightforward maintenance reduce downtime A 32 mm shank and standard Torx clamping arrangement ensure a robust mechanical fit in standard toolholders, while the M4x10 Torx clamping screw and T15 key provide easy, safe insert changes. The simple screw-based clamping reduces setup time and the risk of incorrect torque, improving repeatability between tool changes. This combination of features supports efficient workshop routines and lowers the likelihood of unplanned stoppages. Broad insert compatibility to simplify tooling logistics Designed for APKT 1604 indexable inserts, the head accepts inserts from common suppliers, which reduces inventory complexity. Compatibility with Korloy inserts is stated, allowing selection from widely available grades and geometries for roughing, finishing or mixed duty cycles. Using standardised inserts supports a lean stocking strategy and shortens response time when specific grades are required for different materials. Practical design that supports reliable production workflows With a nominal diameter of 100 mm, eight cutting edges and an overall length engineered for compact integration, the tool head balances accessibility with effective cutting leverage. The construction prioritises repeatability and serviceability: when correctly mounted and fastened, the assembly offers stable engagement and consistent cutting performance across repeated cycles. Its weight and dimensions also suit a variety of turret and toolpost arrangements commonly used in production shops. Contact Metav Werkzeuge for tailored tooling advice and reliable supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: T189TM Manufacturer: Teknik Makina Product: Corner tool head for APKT 1604 indexable inserts Compatible inserts manufacturer: Korloy Clamping screw: M4x10 Torx Torx key size: T15 Facts Diameter: 100 mm Shank diameter (D): 32 mm Overall length: 52 mm Weight: 1.53 kg Cutting angle: 90° Cutting edges: 8 Special features Designed for APKT 1604 indexable inserts 90° corner cutting geometry Robust shank for secure fixation Standard Torx clamping for quick insert changes FAQ What materials is the corner tool head suitable for? The corner tool head (T189TM) is specified as a holder for APKT 1604 indexable inserts; insert grade selection determines suitability for specific materials such as steel, cast iron or aluminium. Which insert type fits this tool head? APKT 1604 indexable inserts are supported; the head is compatible with commonly available APKT 1604 inserts from suppliers such as Korloy for varied machining tasks. What is the required tightening tool for insert changes? Insert clamping is performed with an M4x10 Torx screw using a T15 key, as specified for the Teknik Makina corner tool head (T189TM). Can the head be fitted in standard toolholders? Yes, the 32 mm shank diameter allows integration into toolholders designed for that shank size, providing secure mechanical engagement. Is the cutting angle adjustable? The head provides a fixed 90° cutting angle; angle modification would require a different tool head configuration or a different insert geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust rigidity and standardised insert compatibility to reduce machining downtime and improve repeatability; the combination of a 32 mm shank and a 90° cutting angle ensures stable performance in routine turning tasks. Order the tool directly via Metav Werkzeuge or consult their specialists for integration advice. Angle Turning Head T558TM — 90° tool head for APKT 1705 indexable inserts (Teknik Cutting Tools) The Angle Turning Head T558TM is a compact, right-angle tool head designed for external turning with APKT 1705 indexable inserts, offering straightforward compatibility for workshop lathes and tool-change systems. Secure M4x10 Torx clamping with T15 key Fits APKT 1705 indexable inserts by Taegutec 32 mm shank diameter for rigid mounting Ø100 mm head diameter with eight cutting edges Stable machining through rigid design The turning head is built around a 32 mm shank and a Ø100 mm head diameter to provide rigidity where it matters: at the cutting zone. This geometry reduces vibration during cuts, which promotes longer insert life and more consistent surface finish. The comparatively short overall length (52 mm) limits cantilever effect, helping maintain concentricity and repeatability across production batches while supporting reliable cycle times on medium-duty lathes. Fast insert changes and standard clamping Compatibility with APKT 1705 inserts simplifies stock management and insert procurement; the clamping system uses an M4x10 Torx screw tightened with a T15 key for secure, repeatable seating. The head accepts inserts from Taegutec, a widely available supplier, so replacement parts are easy to source. The 90° cutting angle gives a defined right-angle geometry that is beneficial for shoulder turning and face-off operations, while the indexed eight cutting edges enable quick rotation to fresh cutting faces without toolholder removal. Workshop integration and handling benefits Weighing 1.62 kg, the head combines solid mass with manageable handling for toolsetters and operators. The compact profile facilitates mounting in standard tool posts or turret stations without excessive overhang. Routine maintenance is limited to insert indexing and periodic torque checks on the Torx screw, keeping downtime low. When fitted with the correct inserts, the head supports consistent results across repeat jobs and lends itself to standardised fixture and process documentation in production environments. Contact Metav Werkzeuge for stock status, tailored mounting recommendations and batch availability of the Teknik Cutting Tools Angle Turning Head T558TM Technical data SKU: T558TM Manufacturer: Teknik Makina Type: Angle turning head for indexable inserts For inserts: APKT 1705 Compatible insert maker: Taegutec Clamping screw: M4x10 Torx key: T15 Dimensions & weights Shank diameter: 32 mm Head diameter: 100 mm Overall length: 52 mm Cutting angle: 90° Number of cutting edges: 8 Weight: 1.62 kg Features Fits APKT 1705 indexable inserts Compatible with Taegutec inserts Torx clamping screw M4x10 Torx key size T15 90° cutting geometry Eight cutting edges for indexing FAQ Which insert type is required for this head? The head is designed for APKT 1705 indexable inserts; compatible inserts from Taegutec will fit the clamping system supplied with the Angle Turning Head T558TM. What is the shank diameter for mounting? The tool holder uses a 32 mm shank diameter for mounting in standard tool posts and turret adapters. How is the insert secured in the tool head? An M4x10 Torx clamping screw secures the insert; the matching Torx key size is T15 for tightening and indexing. Is the cutting geometry suitable for shoulder turning? Yes, the 90° cutting angle is appropriate for shoulder faces and right-angle turning operations, providing a defined cutting geometry for such tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of a rigid 32 mm shank, a 90° cutting angle and compatibility with APMT 11T3 indexable inserts to maintain accurate corner and face machining with minimal setup time; order via Metav Werkzeuge or request guidance from their technical consultants. Corner tool head T258TM – indexable insert holder for APMT 11T3, 32 mm shank (Teknik Makina) A compact Corner tool head T258TM for secure mounting of APMT 11T3 indexable inserts, engineered to support precise corner and facing operations in general workshop and light industrial milling setups. Corner tool head T258TM by Teknik Makina Compatible with APMT 11T3 inserts (Korloy) 32 mm shank diameter for secure clamping 90° cutting angle, overall length 63 mm Stable geometry for repeatable precision The holder is built around a 32 mm shank and a 100 mm head diameter to provide a stable interface with standard tool posts and turret adaptors. That greater mass and contact area reduce vibration and support repeatable accuracy during each pass, which in practical terms means fewer rejects and less rework. The unit’s weight of 1.81 kg contributes to damping of high-frequency chatter, improving surface finish without additional balancing. Where setup time is at a premium, a stable tool head cuts cycle variability and helps achieve consistent component quality. Fast insert changes and clear compatibility Designed specifically for APMT 11T3 format inserts and compatible with Korloy insert grades, the head features a Torx retention system (Torx screw M2.5x5.5, Torx key T8) for reliable clamping and quick changeover. Indexable inserts allow the cutting edge to be rotated or replaced without altering tool geometry, which conserves machine setup and reduces tooling costs over time. The Torx fixing provides a secure seat to maintain cutting orientation and repeatability, and the clear specification of the retention parts simplifies spare-part sourcing for maintenance planning. Practical integration and machining benefits With a 90° cutting angle and 63 mm overall length, the head is suited to facing and shoulder operations where a square approach is required. The design supports standardised toolholder bores and fixtures, so the holder integrates into existing tooling systems with minimal adaptation. The combination of robust clamping, standardised insert format and compact footprint reduces downtime during tool changes and streamlines workshop logistics. For production environments focused on throughput and surface quality, the head offers a pragmatic balance of rigidity and serviceability. Contact Metav Werkzeuge today to secure procurement advice or confirm machine compatibility for the Corner tool head T258TM — technical consultants are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: T258TM Brand: Teknik Makina Product name: Corner tool head For inserts: APMT 11T3 For insert manufacturer: Korloy Facts Shank diameter: 32 mm Head diameter: 100 mm Overall length: 63 mm Weight: 1.81 kg Cutting angle: 90° Torx screw: M2.5x5.5 Special features Torx key size: T8 Compatible with indexable inserts Designed for corner and face machining Solid construction for vibration damping FAQ What insert type fits this tool head? The Corner tool head T258TM accepts APMT 11T3 indexable inserts; compatible insert grades from Korloy are indicated in the technical data and can be used according to the intended machining task. How is the insert secured to the head? Insert retention is by a Torx screw specified as M2.5x5.5; the Torx key required for tightening and loosening is size T8, providing a secure and repeatable clamping force. Which machines or holders is the head suited for? The head is configured with a 32 mm shank, making it suitable for tool posts and adaptors designed for that shank diameter; compatibility should be checked against the machine’s toolholder bore and clamping scheme. Does the head support heavy-duty roughing? The robust construction and mass (1.81 kg) give good damping characteristics; for heavy-duty roughing it is necessary to match the insert geometry and grade to the application, using the APMT 11T3-compatible inserts specified. What are the primary benefits of using this head in production? Using the Corner tool head T258TM reduces setup time through standardised insert mounting, improves stability with its 32 mm shank and head mass, and supports consistent surface quality via the 90° cutting angle. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust stability, efficient cooling and quick insert changeover for reliable cycle times and reduced downtime — order directly via Metav Werkzeuge or ask one of our consultants for application support. Angle tool head for BOMT 1304 indexable inserts by Teknik Makina — 100 mm diameter, internal coolant Angle tool head designed for shoulder and face machining where a precise 90° cutting angle and secure insert clamping are required 100 mm diameter for stable machining Internal coolant for improved chip control Compatible with BOMT 1304 inserts 11 cutting edges for increased productivity Greater process stability through robust geometry and size The compact, heavy-duty design of this tool head provides a solid basis for repeatable results in demanding production environments. The 100 mm diameter and a total length of 50 mm combine to reduce deflection and vibration, which helps maintain dimensional accuracy on workpieces and extends tool life. Fitted inserts are fixed with an M3.5x8.5 screw using a Torx T10 drive for secure clamping; this system ensures consistent seat contact and minimises micro-movement during high‑load cuts. The construction therefore supports efficient material removal with predictable surface quality and contributes to measurable cycle-time improvements on the shop floor. Efficient cooling and fast insert handling for higher throughput Integrated internal coolant channels deliver cutting fluid directly to the cutting zone, improving heat dissipation and assisting chip evacuation. This targeted cooling reduces thermal wear on the insert grade and the tool seat, allowing longer tool life and more consistent cutting performance. The head accepts BOMT 1304 indexable inserts and is compatible with inserts from Ingersoll, enabling quick index changes and reduced machine downtime. With 11 cutting edges available across the set-up, production runs can be optimised for cost per component while maintaining process reliability. Practical advantages for workshop and production use Engineered for industrial metalworking, this indexable tool head is suitable where a true 90° cutting angle is required for shoulders and face operations. The solid build (approx. 2.54 kg) provides inertia that helps steady heavy cuts, while the standardised fixing hardware (Torx and M3.5x8.5 screw) allows straightforward maintenance and predictable repeatability when replacing inserts. Supplied as a dedicated solution for BOMT 1304 tooling systems, the component reduces vendor complexity when sourced through a precision partner and fits into established process chains with minimal adaptation. For technical advice, availability or rapid delivery from Metav Werkzeuge — including application guidance for Teknik Makina angle tool heads — contact our Emmerich centre at +49 2822 7131930 or info@metav-werkzeuge.com to discuss specification and lead times. Technical data SKU: T971TM Product type: Angle tool head for BOMT 1304 Manufacturer: Teknik Makina Internal coolant: Yes Weight: 2.54 kg Facts Diameter: 100 mm Total length: 50 mm Cutting edges: 11 Cutting angle: 90° Torx key: T10 Torx screw: M3.5x8.5 Special features Compatible with BOMT 1304 indexable inserts Compatible insert manufacturer: Ingersoll Label: 100mm Eckmesserkopf BOMT 1304 L50mm mit Innenkühlung FAQ What insert type fits this head? The head accepts BOMT 1304 indexable inserts; compatibility with Ingersoll‑made inserts is specified for straightforward procurement. How does the internal coolant improve performance? Internal coolant channels deliver fluid directly to the cutting edge, reducing temperature at the tool‑workpiece interface and aiding chip control; this extends insert life and stabilises cutting conditions for the angle tool head. Is the clamping system durable and easy to service? Yes — the insert is secured with an M3.5x8.5 screw tightened with a Torx T10, offering repeatable clamping torque and simple maintenance during insert changes. Which applications are best suited for this tool head? The component is designed for shoulder and face operations where a true 90° cutting angle and solid tool support are needed, making it suitable for production workshops and toolrooms using BOMT 1304 inserts. Does the head provide improved rigidity for heavy cuts? The 100 mm diameter and compact 50 mm length, combined with the head’s mass (approx. 2.54 kg), enhance rigidity and help reduce vibration during higher‑load machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 100 mm diameter body, precise 90° cutting geometry and integrated internal coolant to secure reliable shoulder turning and efficient chip evacuation; order the corner tool head directly via Metav Werkzeuge or consult our specialists for compatibility questions. Corner tool head T494-1TM – 100 mm diameter, 90° cutting angle (Teknik Makina) A Corner tool head designed for industrial turning with LNGX 1307 indexable inserts, offering internal coolant and compact 50 mm overall length for accurate shoulder machining. 100 mm diameter for stable cutting 90° cutting angle for precise shoulder turning Internal coolant for improved chip evacuation Compatible with LNGX 1307 inserts by Walter High stability and repeatable shoulder accuracy The robust design of this turning head combines a 100 mm diameter body with a short 50 mm overall length, delivering improved rigidity and reduced vibration during shoulder cuts. Such geometry results in stable performance and consistent dimensional accuracy when performing 90° operations. The mass of 1.542 kg contributes to dampening chatter; in practice this reduces rework and helps maintain surface finish when working at moderate to heavy cutting depths. The compact form also supports integration into existing toolholders with a clear focus on repeatability. Controlled cooling and cleaner chip flow for longer tool life Equipped with internal coolant, the head directs cutting fluid close to the cutting edge to aid lubrication and cooling where it matters most. Targeted cooling improves heat dissipation at the shear zone, which in turn supports longer insert life and more predictable wear patterns. Better chip control reduces recutting and helps maintain cycle times; for shops aiming to increase uptime, this feature translates into fewer unscheduled tool changes and steadier productivity. The internal supply is especially useful in operations that demand consistent surface integrity. Proven compatibility and simple, secure clamping The turning head is specified for LNGX 1307 indexable inserts and is compatible with inserts from Walter, enabling straightforward sourcing and replacement. Assembly uses a Torx T15 driver and M4x11 torque screw, which are standard in many workshops and facilitate quick maintenance. The design accommodates seven cutting edges on the assembly, offering clear technical information for inventory planning and reconditioning cycles. Such standardisation reduces conversion effort when retrofitting existing setups and supports fast tool change procedures. Practical integration into workshop workflows With a 32 mm mounting diameter and a compact footprint, the head is designed for easy adoption in standard turning stations and modular tool systems. Precise 90° cutting geometry makes it suited to shoulder turning and facing tasks where right-angled profiles are required. The combination of robust construction, targeted coolant and standard fasteners means the unit can be maintained with common workshop tools, helping to keep maintenance intervals short and predictable. This pragmatic approach aligns with operational needs for dependable tooling and simplified stock management. Discuss specification and procurement of the Teknik Makina corner tool head with Metav Werkzeuge – direct supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: T494-1TM UID: T494-1TM Product type: Corner tool head Label: 100mm Eckmesserkopf LNGX 1307 L50mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 100 mm Overall length: 50 mm Mounting diameter: 32 mm Weight: 1.542 kg Cutting angle: 90° Cutting edges: 7 Torx key: T15 Torx screw: M4x11 Special features Internal coolant For LNGX 1307 indexable inserts Compatible with Walter inserts FAQ Which indexable inserts fit this corner tool head? The head accepts LNGX 1307 indexable inserts; compatibility with inserts from Walter is specified for the corner tool head T494-1TM by Teknik Makina. Does the turning head provide internal coolant? Yes — the corner tool head T494-1TM features internal coolant, supplying fluid directly to the cutting zone to aid cooling and chip evacuation. What does a 90° cutting angle mean for workshop applications? A 90° cutting angle on this turning head enables accurate shoulder turns and right-angled profiles, making the head suitable for precise face and shoulder machining tasks. What are the main dimensions to check before ordering? Key dimensions for the T494-1TM are 100 mm diameter, 50 mm overall length and 32 mm mounting diameter; the weight is 1.542 kg. Which fasteners are required for assembly and maintenance? Assembly uses a Torx T15 driver and M4x11 screw, standard items for workshop maintenance on the Teknik Makina corner tool head. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise geometry and secure clamping for consistent shoulder turning. The compatibility with LNMT 1306 indexable inserts and the D32 shank ensure stable mounting and predictable tool life. Order directly via Metav Werkzeuge or request a specialist consultation for holder selection. Corner tool head T231TM – Turning head for LNMT 1306 indexable inserts, D32 shank (Teknik Makina) A durable corner tool head engineered for reliable shoulder and face-turning operations with LNMT 1306 indexable inserts Fits LNMT 1306 indexable inserts compatible with ISCAR 32 mm D shank for secure toolholder mounting 90° cutting angle for precise shoulder turning Torx fixings M4x10 with T15 key for fast insert clamping Consistent results from proven insert compatibility The turning head is designed around the standard geometry of indexable inserts, notably the LNMT 1306 form, providing repeatable cutting geometry for serial production. By accepting inserts from established suppliers such as ISCAR, the component reduces setup time and simplifies inventory: spare inserts are readily available and replacement is straightforward. This compatibility translates into reduced downtime and a steady surface finish across batches, which is decisive in machining series parts where process consistency matters. Rigid mounting and geometry for stable machining The tool head’s D32 shank and 100 mm tool diameter combine to deliver secure seating in the toolholder and reduced susceptibility to chatter. A true 90° cutting angle supports accurate shoulder and planing cuts while promoting uniform chip flow. The unit’s mass (1.682 kg) contributes to damping dynamics on heavy cuts, helping to preserve insert life and to achieve a cleaner finish on the workpiece. These engineering choices result in improved dimensional repeatability and predictable tool-change intervals for production environments. Quick clamping and practical service routines Insert retention is accomplished with a Torx M4x10 fixing tightened with a T15 key, enabling fast, repeatable clamp torque during changeover. The compact overall length and robust fastening reduce the need for frequent readjustment and make routine maintenance straightforward. Clear mechanical interfaces mean fewer variables during reassembly, which shortens repair windows and supports sustained throughput. For applications requiring standard shoulder turning geometry, this head offers a pragmatic balance of accessibility and industrial robustness. Contact Metav Werkzeuge for tailored advice on toolholder matching and production integration — experts are available to recommend the correct holder and to confirm compatibility with existing turning centres Technical data Article number: T231TM Manufacturer: Teknik Makina Suitable for: LNMT 1306 indexable inserts Compatible insert brand: ISCAR Torx screw: M4x10 Facts Shank diameter: 32 mm Weight: 1.682 kg Diameter: 100 mm Overall length: 50 mm Cutting angle: 90° Number of cutting edges: 10 Special features Torx key: T15 Designed for shoulder turning and facing Robust clamping for repeatable insert seating FAQ What inserts fit this turning head? The corner tool head accepts LNMT 1306 indexable inserts; inserts from ISCAR are compatible and match the head’s insert pocket geometry. What shank size is required for the toolholder? The tool head uses a 32 mm shank (D32) for secure mounting; ensure the holder accommodates a D32 shank for optimal rigidity. Which cutting operations is the head suited for? This tool head is designed for shoulder and facing operations where a 90° cutting angle and stable insert seating deliver repeatable results. How is the insert secured and changed? Insert clamping is performed with a Torx screw M4x10; the screw is driven with a T15 key for consistent torque and fast changeover. Manufacturer: Teknik Cutting Tools; Buyukkayacık OSB Mah. 422 Nolu Sokak No:9; Selcuklu/KONYA; Turkey / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of a 90° cutting angle, a 100 mm diameter and secure Torx fixation for predictable turning performance; order the corner tool head directly via Metav Werkzeuge or ask the consultants for application advice. Corner tool head T390TM — 90° 100 mm indexable tool head by Teknik Makina The Corner tool head T390TM is an angled turning head engineered for reliable facing and shoulder operations using LNMX 1006 indexable inserts. 100 mm diameter for stable machining 90° cutting angle for facing and shoulder work Compatible with LNMX 1006 indexable inserts 32 mm shank with M3x7 Torx fixation Consistent machining performance through precise geometry The T390TM tool head combines a 100 mm diameter body with a 90° cutting angle to provide a stable support platform that reduces vibration during facing and shoulder turning. The robust geometry helps maintain a constant cutting line, improving surface finish and extending insert life — a tangible efficiency gain on medium- to high-duty cycles. Compatibility with standard LNMX‑type inserts allows straightforward integration into existing tooling systems while ensuring repeatable results on workpieces where dimensional control is critical. Secure clamping and low-maintenance changeover A deliberate fixation design featuring an M3x7 Torx screw secured with a T8 key provides reliable insert retention and simple servicing. The 32 mm shank (mount) offers a firm connection to the toolpost or boring bar, reducing micro-movement that can compromise tolerances. Quick, tool-assisted insert changes reduce downtime, and the straightforward screw interface supports predictable torque control during maintenance, contributing to consistent tool seating and repeatability across production batches. Workshop-ready design for predictable integration With an overall height of 50 mm and a nominal weight of 1.7 kg, the head is dimensioned for straightforward mounting and balance within standard turning setups. The construction supports common industrial workflows and is supplied optimised for LNMX 1006 inserts from Korloy, simplifying procurement and stocking. Backing by Teknik Makina signals manufacturing consistency, while distribution through Metav ensures accessible supply and a clear route for technical clarification or ordering. Contact Metav Werkzeuge for tailored application advice on Teknik Makina tool heads and to request specification support — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: T390TM Manufacturer: Teknik Makina For: LNMX 1006 Indexable Inserts Compatible insert maker: Korloy Core data Diameter: 100 mm Overall height: 50 mm Shank diameter (mount): 32 mm Weight: 1.7 kg Cutting angle: 90° Cutting edges: 9 Special features Torx screw: M3x7 Torx key: T8 SKU: T390TM FAQ Which inserts are compatible with this tool head? The corner tool head T390TM is designed for LNMX 1006 indexable inserts and is compatible with Korloy LNMX 1006 grades for a variety of materials. What is the mounting diameter required? Mounting requires a 32 mm shank connection; the specification for the T390TM lists a 32 mm mount diameter. What cutting angle does the head provide and for which operations is it suited? The head features a 90° cutting angle, making it well suited to facing, shoulder turning and applications where a square cut geometry is required. How are the inserts secured in the tool head? Inserts are secured with an M3x7 Torx screw that is tightened using a T8 key, providing secure fixation and straightforward changeover. Is the tool head suitable for industrial turning applications? Yes, the T390TM’s 100 mm diameter, solid mount and engineered fixation make it appropriate for robust turning tasks within industrial workshop environments. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust build quality, integrated internal coolant, and proven compatibility with R390 18 indexable inserts to ensure stable, repeatable machining cycles; order the corner milling head directly via Metav Werkzeuge or ask the consultants if needed. Corner milling head T428-1TM for R390 18 indexable inserts — 100 mm diameter, internal coolant (Teknik Makina) Corner milling head T428-1TM designed for face and shoulder machining with R390 18 indexable inserts, providing coolant-fed cutting and high rigidity in production environments. 100 mm diameter for stable cutting Internal coolant for improved chip evacuation Compatible with R390 18 Sandvik inserts 90° cutting angle for square shoulder machining Stable, repeatable cutting for production environments The corner milling head is engineered to deliver consistent results in batch and series production. With a 100 mm diameter and a compact overall length of 52 mm, the geometry provides increased stiffness and reduced vibration during heavy engagement cuts. Compatibility with R390 18 indexable inserts (Sandvik-compatible) allows the use of widely available grades and corner radii, simplifying process planning. The robust mass (1.595 kg) contributes to stable spindle loads and predictable cutting forces, which supports repeatable surface quality and machining tolerances. Integrated coolant for longer tool life and reliable surface finish Built-in internal coolant channels feed cutting fluid directly to the insert edge, improving chip control and reducing thermal load at the cutting zone. This targeted coolant delivery helps maintain cutting edge integrity, delays wear, and can extend indexable insert life under continuous operation. Better chip evacuation also lowers the risk of re-cutting, leading to more consistent part finishes and fewer unplanned interventions on the machine, which benefits cycle-time reliability across shifts. Simple, secure clamping to speed up changeovers The design focuses on straightforward assembly and secure fixing: fasten the insert with the specified Torx T15 key and M4x10 Torx screws for a firm seat and repeatable insert positioning. The 90° cutting angle is ideal for square shoulder operations, while the compact L52 mm overall length improves access in tighter tool turrets. Together, these features reduce set-up time and support efficient tool changes, helping to minimise downtime in mixed-production environments where flexibility and quick return to cutting are essential. Contact Metav Werkzeuge to discuss how the Teknik Makina corner milling head T428-1TM aligns with specific production needs or to request a tailored quotation directly from the experts at Metav Werkzeuge. Technical data Article number: T428-1TM UID: T428-1TM Product type: Corner milling head Variant: for R390 18 indexable inserts Data Diameter: 100 mm Overall length: 52 mm Weight: 1.595 kg Cutting angle: 90° Cutting edges: 7 ECLASS: 21181015 Special features Internal coolant Compatible with R390 18 indexable inserts Fits Sandvik insert ranges Torx key: T15 Torx screw: M4x10 Manufacturer: Teknik Makina FAQ Which insert family fits this cutter head? The cutter head accepts R390 18 indexable inserts and is compatible with standard Sandvik R390 18 grades and geometries. Is coolant supplied through the tool? Yes, the tool includes internal coolant channels for direct feed to the cutting edge to improve chip control and tool life. What are the main dimensions and mass? The tool has a diameter of 100 mm, an overall length of 52 mm and weighs 1.595 kg. What fixing hardware is required for the inserts? Inserts are secured using M4x10 Torx screws tightened with a Torx T15 key to ensure a repeatable, secure clamp. For which machining tasks is the tool optimised? The head is optimised for square shoulder and face machining where a 90° cutting angle and strong rigidity are required. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of a 90° cutting geometry, a 32 mm shank and six cutting edges for stable, repeatable corner turning and reduced rework; order the component via Metav Werkzeuge or request advice from our technical consultants. Corner cutting head T102TM – 90° geometry, Ø100 mm for TPKN 1603–2204 indexable inserts (Teknik Makina) The Corner cutting head T102TM is a compact, rigid turning head engineered for 90° corner operations with TPKN 1603–2204 indexable inserts, designed for lathe and CNC toolpost applications. *90° cutting geometry for precise corner cutting *Compatible with TPKN 1603–2204 indexable inserts *32 mm shank diameter for secure clamping *Six cutting edges for long service intervals Accurate corner turning that saves machining time The 90° configuration delivers a true right‑angle cut that simplifies setup and reduces secondary operations. With a Ø100 mm head diameter and six cutting edges, the assembly maintains cutting stability across repetitive cycles, which leads to fewer vibrations and improved surface quality. This geometry is particularly effective where shoulder or face turning calls for crisp corners and consistent tolerance control, translating directly into shorter cycle times and less scrap. Secure clamping and straightforward assembly for uptime A 32 mm shank provides a standardised interface for rigid attachment in many toolposts and adapters, while the mechanical fixation is achieved with a locking screw M6x17 and an M3 hex screw, using a 4 mm Allen key for adjustment. The clamping plate reference TA010 ensures correct seat and repeatable indexing when replacing inserts. Together these features enable fast insert replacement and consistent clamping force, reducing setup variation and machine downtime. Production-ready durability and predictable performance Constructed for workshop and industrial use, the unit’s mass (approx. 1.518 kg) contributes to a balanced toolhead that resists chatter and extends insert life under continuous use. Compatibility with TPKN 1603–2204 indexable inserts allows selection of grades and geometries to match materials and cutting parameters; the result is predictable tool life and lower per‑component machining costs. The combination of robust construction and standard insert format supports both single‑piece and batch production environments. Where this toolhead excels in the workflow The design is well suited to turning centres that require precise shoulder formation and repeatable corner finishes. The holder’s secure interface and standard insert family make it a practical choice for contract workshops, maintenance departments and production lines aiming to reduce tool change time and increase first‑pass quality. For enquiries on matching insert grades or setting recommended cutting data, Metav’s technical advisors provide application guidance and stock information. For tailored technical advice on the Teknik Makina T102TM corner cutting head and fast supply from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: T102TM Manufacturer: Teknik Makina Designation: Corner cutting head (Eckmesserkopf) For inserts: for TPKN 1603–2204 Indexable Inserts Facts Diameter: 100 mm Shank diameter (D): 32 mm Total length: 52 mm Weight: 1.518 kg Cutting angle: 90° Number of cutting edges: 6 Special features Suitable for TPKN 1603–2204 indexable inserts Locking screw: M6x17 Clamping plate: TA010 Hex screw: M3 Allen key size: 4 SKU: T102TM FAQ Which indexable inserts fit this toolhead? The T102TM accepts TPKN 1603–2204 indexable inserts; this standard insert family provides options for grades and geometries to suit a wide range of materials. What toolpost or adapter size is required? The holder features a 32 mm shank diameter, so a corresponding 32 mm toolpost or adapter is required for secure mounting. Is the toolhead suitable for heavy roughing cuts? The mass and balanced design give good stability for moderate roughing and finishing operations; for heavy stock removal select an insert grade and cutting parameters matched to the workpiece material. Which fasteners and accessories are used for assembly? Assembly and clamping reference the M6x17 locking screw, the TA010 clamping plate and an M3 hex screw; a 4 mm Allen key is used for tightening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust 100 mm tool body with internal coolant and a true 90° shoulder geometry for efficient, repeatable shoulder milling; order the tool via Metav Werkzeuge or contact our consultants for application support. T846-1TM 100 mm 90° indexable shoulder milling head by Teknik Makina The T846-1TM is a 90° indexable shoulder milling head designed for precision shoulder milling with XNEX 0806 indexable inserts, offering internal coolant and a compact 52 mm overall length for confined setups. 100 mm diameter for stable machining Internal coolant for improved chip evacuation Compatible with XNEX 0806 inserts (SECO) Eight cutting edges, 90° shoulder geometry High productivity through stable cutting geometry The head’s 100 mm diameter and rigid body provide a stable platform that reduces vibration during shoulder cuts, which translates into higher surface quality and extended insert life. The 90° cutting angle is engineered for true square shoulders, enabling accurate face and shoulder operations with predictable tolerances. Where cycle time and consistent results matter, this tool head delivers measurable productivity gains by allowing higher feed rates while maintaining component quality. Improved process reliability with directed cooling Equipped with internal coolant, the cutter head channels cooling directly to the insert pocket, improving chip control and heat dissipation. This arrangement reduces thermal load on the cutting edge and minimises built-up edge formation, so tool life is increased and rework risk is lowered. The internal coolant capability is particularly beneficial in medium- to high-speed machining where thermal stability impacts dimensional accuracy and surface finish. Simplified integration and maintenance in the workshop Compatibility with XNEX 0806 indexable inserts and standard fastening (Torx key T15, screw M4x12.5) means the head can be serviced quickly using common workshop tools. The mounting and insert change routines are straightforward, reducing downtime and supporting continuous production. The design’s accessibility and standardised fastenings help maintenance teams to perform quick insert indexing and clamp checks without specialised equipment. Versatile applications and material capability With eight insert positions and a robust construction, the tool head is suited to shoulder milling tasks across a range of components where square faces and shoulders are required. The combination of indexed insert use and direct coolant support makes it suitable for operations demanding repeatability and surface integrity. For setups where space is limited, the 52 mm overall length provides a compact option without sacrificing stiffness. Contact Metav Werkzeuge for tailored advice on using the Teknik Makina T846-1TM in specific production environments, or to arrange procurement and delivery from our Emmerich location — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: T846-1TM Label: 100mm Eckmesserkopf XNEX 0806 L52mm mit Innenkühlung Product type: Eckmesserkopf Manufacturer: Teknik Makina eClass: 21181015 Facts Diameter: 100 mm Overall length: 52 mm Weight: 1.755 kg Cutting edges: 8 Cutting angle: 90° Special features Internal coolant: yes Compatible inserts: XNEX 0806 Compatible insert manufacturer: SECO Torx key: T15 Torx screw: M4x12.5 SKU: T846-1TM FAQ What inserts are compatible with this head? The T846-1TM is designed for XNEX 0806 indexable inserts and is specified as compatible with SECO insert variants using that geometry. Does the head provide coolant supply to the cutting edge? Yes, the head features internal coolant, supplying fluid directly to the insert pocket to improve chip evacuation and thermal control. What fastening is required for insert screws? Insert screws use a Torx interface; a T15 Torx key fits the fastening and the specified screw size is M4x12.5. Is the tool suitable for tight working envelopes? The compact 52 mm overall length makes the head suitable for confined setups while preserving rigidity for shoulder machining. How many cutting edges are available per head? The head accommodates eight indexed cutting edges, optimised for 90° shoulder operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine high-precision geometry with robust mounting and wide compatibility to keep turning processes consistent and predictable; take advantage of the 90° cutting angle and 32 mm shank for rigid set-ups. Order the tool directly through Metav Werkzeuge or consult the team for specification support. Corner Tool Head T846TM – 90° indexable insert holder with 32 mm shank (Teknik Cutting Tools) The Corner Tool Head is a compact indexable insert holder developed for XNEX 0806 inserts, delivering a defined 90° cutting geometry suited to facing and external turning operations *Rigid 90° cutting geometry *32 mm shank for secure mounting *Compatible with XNEX 0806 inserts *Accepts SECO and WINSTAR inserts Precise 90° geometry for predictable turning results Engineered to maintain a consistent profile during facing and square-cut operations, the holder features a 90° cutting angle that ensures repeatable engagement with the workpiece. The specified cutting layout—accepting XNEX 0806 indexable inserts—reduces tolerance creep and simplifies process planning, since a reliable insert family and a defined geometry allow accurate calculation of tool offsets and cutting depths. This technical certainty supports cycle-time optimisation and lowers scrap rates in batch production. Robust clamping and compact dimensions support rigidity A 32 mm shank and a robust body diameter of Ø100 mm provide the mechanical stiffness necessary for stable cutting, while the compact overall length of 52 mm helps to minimise overhang. Fastening is by an M4x12.5 Torx screw (T15), offering a repeatable and secure clamp with straightforward serviceability. The unit weight of 1.755 kg contributes to a balanced spindle load and predictable dynamic behaviour, important for achieving consistent surface finish and prolonging insert life. Broad compatibility reduces inventory complexity The head is prepared for the XNEX 0806 insert family and is compatible with insert manufacturers SECO and WINSTAR, enabling flexible procurement and simple replacement strategies. Standardised insert use cuts stocking complexity and aligns with lean tooling practices, while the solid construction supports heavy-duty turning where repeatability is critical. For workshops seeking dependable toolholding that integrates into existing tool sets, this head offers a pragmatic combination of standard interfaces and durable design. For specification advice or to confirm fitment, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 to discuss the Teknik Cutting Tools Corner Tool Head T846TM and its suitability for precise 90° turning applications Technical Data Article number: T846TM Designation: Corner Tool Head for XNEX 0806 indexable inserts Manufacturer: Teknik Cutting Tools (Teknik Makina) Core dimensions Shank diameter: 32 mm Diameter: 100 mm Overall length: 52 mm Weight: 1.755 kg Cutting angle: 90° Cutting edges: 7 Materials & compatibility Compatible with XNEX 0806 indexable inserts Suitable for SECO and WINSTAR inserts Fastening: M4x12.5 Torx screw (T15) FAQ What insert type fits this tool head? The Corner Tool Head T846TM is designed for XNEX 0806 indexable inserts and accepts compatible grades from SECO and WINSTAR. Which shank diameter is required for the holder? Mounting requires a 32 mm shank interface; the compact design supports secure clamping and reduced overhang. How is the insert secured in the head? Inserts are retained by the specified clamp arrangement and secured using an M4x12.5 Torx screw (T15) for consistent seat and repeatable reassembly. Is the head suitable for facing and external turning? Yes—the defined 90° cutting geometry makes the head suitable for facing and square external turning operations where precise shoulder and step features are required. What level of balancing or dynamic behaviour can be expected? With a balanced form factor and a weight of 1.755 kg, the head provides stable dynamic behaviour for standard turning speeds when installed with the correct shank and spindle setup. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from stable mounting and high productivity thanks to the combination of a 40 mm shank and eight cutting edges; compatibility with XNKT 0805 indexable inserts simplifies tooling choices. Order the corner tool head directly via Metav Werkzeuge or ask our consultants if needed. Corner tool head – for XNKT 0805 indexable inserts, 100 mm diameter (Teknik Makina) The Corner tool head designed for turning and facing operations with XNKT 0805 indexable inserts, offering a compact 100 mm diameter head for robust workshop and CNC use. Compact 100 mm head diameter Designed for XNKT 0805 inserts 40 mm shank for secure mounting Eight cutting edges for increased productivity Stable mounting for consistent surface quality A solid 40 mm shank provides high radial stability and reduces vibration during turning and facing tasks. The mass and geometry of the head are engineered to transfer cutting forces evenly, which leads to improved surface finishes and longer insert life. By combining a stiff clamping interface with the correct screw interface (M4x10 Torx) and required tool bit engagement (T15 key), the head supports reproducible setups and faster cycle times on serial production runs. Built for efficient indexable-insert machining Compatibility with XNKT 0805 indexable inserts makes insert selection straightforward and cost-effective. The head accepts standard inserts from Korloy, enabling flexible edge geometry choices for different materials and cutting conditions. With eight cutting edges, tool change intervals are extended and downtime minimised, providing a direct performance advantage in medium- to high-volume turning. The modular concept keeps tooling logistics simple and reduces total tool inventory. Easy maintenance and secure clamping Maintenance is straightforward: the head uses a standard M4x10 Torx fixing and a T15 key for reliable clamp torque. Fast access to the clamping screw and clear tool geometry reduce risk of incorrect assembly. The pragmatic design supports routine checks and quick insert indexing, so workshops can maintain throughput without complex tooling procedures. The robust construction also assists repeatable alignment when changing heads between machines. Suitable for workshop and industrial applications The tool head’s dimensions — 100 mm diameter and 52 mm overall height — are optimised for common turning and facing setups while keeping tool overhang moderate. At a weight of 1.575 kg, the unit balances rigidity with manageable handling during tool change. Manufactured by Teknik Makina, this head is aimed at both independent workshops and production environments that require reliable, repeatable performance with standardised indexable inserts. Contact Metav Werkzeuge for tailored advice on Teknik Makina’s corner tool head T907TM with a 100 mm diameter and secure 40 mm shank mounting — assistance is available from our Emmerich-based specialists to ensure the right configuration for the application Technical data Article number: T907TM Manufacturer: Teknik Makina Suitable for inserts: XNKT 0805 Compatible insert manufacturer: Korloy Screw type: M4x10 Torx Torx key: T15 Weight: 1.575 kg Facts Diameter: 100 mm Overall height: 52 mm Shank diameter: 40 mm Cutting edges: 8 Special features Designed for indexable insert turning and facing Robust shank for reduced vibration Quick-access Torx clamping screw Compatible with Korloy XNKT 0805 inserts Manufacturer: Teknik Makina FAQ What inserts does the corner tool head accept? The corner tool head is designed for XNKT 0805 indexable inserts and is compatible with Korloy inserts of that designation. What are the mounting dimensions for this head? Mounting requires a 40 mm shank seat and the head’s diameter is 100 mm with an overall height of 52 mm. How many cutting edges are available on the tool head? The unit provides eight cutting edges, increasing productive runtime before index or insert replacement is needed. Which fastener is used to secure the insert or clamp? A M4x10 Torx screw secures the clamping mechanism; a T15 Torx key is required for tightening. What is the product SKU and who manufactures it? The SKU is T907TM and the head is manufactured by Teknik Makina Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid toolholder that combines a 90° cutting angle, a 32 mm shank and compatibility with XOMX 1204 indexable inserts to deliver stable, repeatable facing and profiling operations. The combination of stout clamping and straightforward insert changes reduces setup time and supports steady production flows—order via Metav Werkzeuge or contact our consultants for specification support. 90° Indexable Turning Head T518TM by Teknik Makina — for XOMX 1204 indexable inserts, 32 mm shank The 90° Indexable Turning Head T518TM is a compact turning head engineered for facing and square-off operations with XOMX 1204 indexable inserts; designed for workshop toolholders with a 32 mm shank and rapid insert replacement. 90° cutting angle for precise facing Suitable for XOMX 1204 indexable inserts 32 mm shank diameter for stable clamping Torx M3.5x8.5 screw with T10 key Consistent results through rigid design and defined cutting geometry A robust toolholder reduces chatter and improves surface finish; the T518TM’s 32 mm shank and substantial head body (head diameter 100 mm) increase rigidity during heavy facing cuts. The 90° cutting angle is especially effective for square-off and finishing passes where dimensional control is critical. By focusing on mechanical stability, this turning head offers a verifiable basis for choosing a holder that helps maintain tolerances and extend insert life, thereby supporting predictable cycle times and process reliability. Fast insert changes and straightforward maintenance to shorten downtime Insert replacement is simplified by the M3.5x8.5 Torx screw and T10 key interface, enabling quick, repeatable clamping without special tooling. Compatibility with XOMX 1204 inserts—also SECO-compatible—allows the use of established insert variants, reducing inventory complexity. This straightforward maintenance routine means less production interruption and faster return to cutting, which can improve throughput when tool changes are frequent or when multiple machines use the same insert family. Practical integration for workshop environments and operator clarity With an overall length of 52 mm and a measured mass of 1.817 kg, the turning head balances compactness with the mass needed to dampen vibration in many lathe setups. The head is prepared for indexable insert use: inserts are indexed rather than re-ground, so component replacement is rapid and repeatable. For those less familiar with indexable tooling, an indexable insert is a replaceable cutting tip seated into the holder; this approach separates the expensive holder from the consumable insert, delivering cost efficiency for workshops that prioritise uptime and consistent part quality. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Cutting Tools T518TM into existing toolholders—our Emmerich facility provides supply and application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T518TM Name: 90° indexable turning head Manufacturer: Teknik Makina Suitable for inserts: XOMX 1204 Core technical data Shank diameter: 32 mm Weight: 1.817 kg Head diameter: 100 mm Overall length: 52 mm Cutting angle: 90° Cutting edges: 10 Special features Torx screw: M3.5x8.5 Torx key size: T10 For indexable inserts: XOMX 1204 Compatible with SECO inserts FAQ Which indexable inserts fit this turning head? The T518TM is designed for XOMX 1204 indexable inserts; SECO-compatible variants can be used where specified. What shank diameter is required for mounting? This turning head has a 32 mm shank and is intended for toolholders that accept a 32 mm diameter mounting. How is the insert secured and changed? Inserts are clamped with an M3.5x8.5 Torx screw, driven with a T10 key, allowing fast, repeatable insert changes for the T518TM. Is the tool suitable for facing heavy cuts? The combination of a substantial head diameter (100 mm), 32 mm shank and 90° cutting angle gives the toolholder the rigidity typically required for reliable facing and square-off operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precise 90° cutting angle and a 32 mm shank for stable clamping and consistent shoulder finishes; compatibility with ADKT 1505 indexable inserts (ISCAR) ensures fast tool changes and predictable process behaviour. Order through Metav Werkzeuge or request technical clarification from our advisors for seamless integration into existing turning setups. Corner turning head T207TM — 90° toolholder for ADKT 1505 indexable inserts, 32 mm shank (Teknik Makina) A Corner turning head T207TM engineered for accurate shoulder and face turning operations in CNC and manual lathes using ADKT 1505 indexable inserts. 90° cutting angle for shoulder turning 32 mm shank diameter for rigid mounting Compatible with ADKT 1505 inserts (ISCAR) Secured by M4x10 Torx screw (T15) High rigidity for precise shoulder finishes The T207TM delivers repeatable shoulder geometry by combining a compact head with a robust shank. The 32 mm shank contributes to reduced vibration and enhanced tool life, while the 90° cutting angle is optimised for square shoulder and facing operations where consistent surface finish and dimensional control are required. For production environments, this stability translates into fewer reworks and improved cycle-time predictability, making the toolholder a rational choice when throughput and accuracy matter. Quick indexable insert handling and secure clamping Designed for ADKT 1505 indexable inserts, the holder accepts common commercial grades and geometries, enabling fast recovery of cutting edge performance. The insert retention is managed with an M4x10 Torx screw, tightened or released with a T15 key, which simplifies insert changes and maintenance routines. The combination of standardised fixing hardware and widespread insert availability reduces downtime and simplifies spare-part logistics, supporting efficient shop-floor workflows. Practical design for workshop and industrial use With a head diameter of 100 and an overall length of 52, the toolhead balances accessibility and strength for a wide range of turning tasks. The component’s mass (approximately 1.546 kg) provides inherent damping for interrupted cuts, while the geometry supports both roughing and finishing passes when paired with the appropriate insert grade. Compatibility with ISCAR-format ADKT 1505 inserts ensures flexible tooling strategies across different materials and applications without the need to redesign tool stations. For shoulder turning tasks that demand repeatability and fast insert exchange, contact Metav Werkzeuge to check availability and request detailed integration advice for the Teknik Cutting Tools corner turning head T207TM via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data SKU: T207TM Manufacturer: Teknik Makina / Teknik Cutting Tools Diameter: 100 mm Shank diameter: 32 mm Overall length: 52 mm Weight: 1.546 kg Cutting angle: 90° Number of cutting edges: 8 Compatible inserts: ADKT 1505 Compatible insert manufacturer: ISCAR Fastening screw: M4x10 Torx Required Torx key: T15 FAQ What inserts fit this turning head? The corner turning head accepts ADKT 1505 indexable inserts; it is designed for standard ADKT 1505 geometries and works with ISCAR-format inserts. Is the holder suitable for heavy-duty shoulder turning? The robust design, 32 mm shank and 90° cutting angle make the holder appropriate for demanding shoulder and face turning tasks where rigidity and repeatability are priorities. Which tool secures the insert and what size is required? Insert retention is via an M4x10 Torx screw; a T15 Torx key is used to tighten or release the screw for insert changes. Can this head be used on most CNC lathes? The 32 mm shank is intended for tooling systems that accept that diameter; the head is suitable where the machine turret or holder accepts a 32 mm interface and the required overhang is within the machine’s capability. What benefit does the 90° cutting angle provide? A 90° angle provides a true shoulder geometry and reliable face finishes, reducing secondary operations for square-edged turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com