Gibt es einen Hahn und Kolb Online Shop?

The combination of a compact shank and secure insert clamping makes this cutter a practical choice for high-repeatability milling in small to medium machining centres; its compatibility with APXT 1003 indexable inserts reduces tool-change time and tooling costs. Order the tool directly via Metav Werkzeuge or consult the technical team for configuration advice. S140TM shank cutter — 16 mm shank, 90° cutting angle by Teknik Makina the S140TM is a shank cutter designed for face and peripheral milling with indexable inserts, primarily for light to medium-duty industrial applications Compact 16 mm shank for tight toolholders 30 mm cutting length for deep engagement Holds APXT 1003 indexable inserts by Korloy Supplied with M2.5x5.5 Torx screw and T8 key Consistent chip control and production repeatability The tool is built to deliver stable machining results when paired with APXT 1003 indexable inserts. By using a dedicated insert interface, the cutter enables predictable chip evacuation and consistent flank contact, which together support reduced rework rates and stable tolerances in serial production. The combination of a 16 mm shank and a 90° cutting angle provides a compact footprint while maintaining effective cutting geometry for facing and light shoulder milling. The modular nature of the insert system also simplifies replacement: worn edges are swapped quickly without regrinding, which shortens downtime and keeps cycle times low. Secure clamping and straightforward maintenance Clamping is achieved using the supplied M2.5x5.5 Torx screw actuated with a T8 key, ensuring the insert pocket is fastened with consistent torque for repeatable seating. This reduces the likelihood of insert movement under load and supports improved tool life through uniform seat pressure. The cutter’s 30 mm cutting length offers enough engagement for many through-cut and slotting operations without excessive cantilever, helping to limit vibration. Routine maintenance is straightforward: inspection of the insert seat and screw before each shift guarantees secure retention and predictable machining behaviour. Practical fit for mixed-workshop environments Designed for compatibility with Korloy and other suppliers of APXT 1003-format inserts, the shank cutter suits workshops that prioritise flexibility and quick tooling changes. The small 16 mm diameter makes it suitable for compact toolholders and spindle configurations commonly found in CNC machining centres and smaller vertical mills. For purchasing and inventory management, the standardised insert format reduces the number of distinct spare parts required, which supports lean stock practices. The S140TM’s modest weight and compact form also make it easy to handle during set-up and toolroom checks. For ordering or technical assistance with the Teknik Makina S140TM shank cutter, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 — the Metav team can advise on compatible inserts and toolholder selection Technical data Article number: S140TM Manufacturer: Teknik Makina Product name: S140TM shank cutter For indexable inserts: APXT 1003 Compatible insert brand: Korloy Facts Shank diameter: 16 mm Cutting length: 30 mm Diameter: 16 mm Number of cutting edges: 2 Overall length: 100 mm Weight: 0.156 kg Cutting angle: 90° Special features Supplied screw: M2.5x5.5 Torx Required key: T8 eClass: 21180806 ETIM: EC011860 Files: ID 62de7eecbd24461b3d5f7a7d, 62de7e5c0f56dbb4de4dbf0f FAQ What insert format does the cutter accept? The cutter accepts APXT 1003 indexable inserts; the S140TM is specified for that insert format and is compatible with Korloy APXT 1003 plates. Which screw and key are required for insert clamping? Insert clamping uses an M2.5x5.5 Torx screw, tightened with a T8 key as supplied with the S140TM shank cutter. Is the S140TM suitable for compact toolholders? Yes — the 16 mm shank diameter is intended for smaller toolholders and compact spindle configurations commonly used in machining centres. How many cutting edges does the cutter have and what does that mean? The cutter has 2 cutting edges, which balances material removal rate and stability; two edges provide efficient cutting with predictable load distribution for light to medium milling tasks. Can the S140TM be used with other APXT 1003 insert manufacturers? Yes — the S140TM is designed for the APXT 1003 insert geometry and can be used with any insert brand that conforms to that format, including Korloy. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-precision milling solution that combines a 16 mm shank, internal coolant and compatibility with BDMT 11T3 indexable inserts for consistent production results; order directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter S565-1TM — 16 mm shank, internal coolant (Teknik Makina) The Shank milling cutter S565-1TM is a CNC-compatible indexable milling tool designed for use with BDMT 11T3 inserts and Kyocera-compatible plates, offering a compact overall length and integrated coolant supply for stable chip evacuation. 16 mm precision shank Internal coolant channel Compatible with BDMT 11T3 inserts Torx T8 fastening system Reliable productivity through indexable tooling This indexable milling solution is engineered for predictable cycle times and low tool-change overhead. Fitted for BDMT 11T3 inserts, the cutter allows rapid re-indexing of cutting edges, reducing downtime compared with solid-tool regrinds. The combination of a 16 mm shank and a balanced design maintains runout control on many tool holders, which helps to protect spindle bearings and improves part-to-part repeatability in serial production. Secure clamping and coolant for consistent cutting conditions Secure retention is provided by the Torx fixing mechanism; the Torx T8 drive and the matching M2.5x5.5 screw ensure a tight, reproducible fit for every insert change. The integrated internal coolant directs lubricant and coolant to the cutting zone, enhancing chip control and thermal stability. With a cutting length 45 mm and 150 mm overall length, the tool gives a useful reach for medium-depth milling while preserving stiffness and surface finish. Compact design with clearly defined specifications A two-flute geometry provides effective chip evacuation while keeping cutting forces manageable; the tool has 2 cutting edges and a total weight of 0.232 kg for easy handling and balanced performance. The shank diameter of 16 mm is a common standard that simplifies adapter and holder selection. Compatibility with Kyocera production inserts means replacement parts are readily available, supporting uninterrupted workflows. Contact Metav Werkzeuge for tailored application support and ordering of the Teknik Makina S565-1TM — our consultants assist with holder selection and machining parameters from Emmerich to your workbench Technical data SKU: S565-1TM Product type: Shank milling cutter Manufacturer: Teknik Cutting Tools Facts Diameter: 16 mm Overall length: 150 mm Shank diameter: 16 mm Cutting length: 45 mm Weight: 0.232 kg Cutting edges: 2 Special features Internal coolant Compatible with BDMT 11T3 inserts Compatible insert manufacturer: Kyocera Torx key: T8 Torx screw: M2.5x5.5 FAQ Which inserts fit this cutter? The cutter accepts BDMT 11T3 indexable inserts; the tool is designed for Kyocera-compatible plates and simple re-indexing. Is the coolant delivered through the tool? Yes, the tool has an internal coolant channel to supply coolant directly to the cutting zone for improved chip evacuation. What are the key dimensional limits to check for a setup? Important dimensions are 16 mm diameter (shank), 45 mm cutting length and 150 mm overall length; these determine holder compatibility and reach. How is the insert secured? Inserts are clamped using a Torx screw system (driver T8) with screw specification M2.5x5.5 for repeatable retention. Can the S565-1TM be used on standard 16 mm holders? Yes, the S565-1TM has a 16 mm shank designed to fit conventional 16 mm toolholders that match the machine's clamping system. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from stable clamping and efficient chip evacuation thanks to the 16 mm shank and internal coolant, combined with compatibility with R390 11T3 indexable inserts for rapid insert changes; order the indexable insert shank cutter (SKU S593-2TM) directly via Metav Werkzeuge or consult our specialists for application support. Indexable insert shank cutter for R390 11T3 — 16 mm shank, internal coolant (Teknik Makina) The Indexable insert shank cutter for R390 11T3 is a coolant-fed milling body designed for secure clamping in standard 16 mm tool holders and for fast insert replacement in production environments. 16 mm shank diameter for stable clamping Internal coolant for improved chip evacuation Compatible with R390 11T3 indexable inserts Torx T8 fixing with M2.5x5.5 screw Coolant-fed design for consistent cutting performance The integrated internal coolant channels direct cutting fluid precisely to the cutting edge, improving chip evacuation and reducing heat at the insert edge. This controlled cooling helps to maintain edge geometry for longer, which translates into more consistent surface finish and longer service intervals for the cutter body. In practice, through‑tool coolant reduces built-up edge and supports higher metal removal rates in CNC milling cycles without compromising the life of the insert. Rigid 16 mm shank for repeatable set-ups A 16 mm shank diameter provides the mechanical stiffness required for stable milling, particularly when machining with indexable inserts. The larger shank reduces vibration and run-out in the spindle, which benefits both repeatability and tool life. For workshops seeking predictable results, the solid shank ensures secure seating in standard collets and tool holders, simplifying set-up and reducing the need for corrective rework. Indexable inserts and fast changeover for cost-effective machining Designed for use with R390 11T3 indexable inserts, this cutter body offers the economic advantage of replaceable cutting edges: worn inserts are changed quickly while the cutter body remains in service. The tool uses a Torx T8 fixing system and an M2.5x5.5 screw for secure and straightforward insert clamping. With two effective cutting edges and a low mass of 0.229 kg, the assembly supports both efficient roughing and controlled finishing operations on automated machining centres. For tailored advice on using the Teknik Makina indexable insert shank cutter or to confirm compatibility with specific insert grades and holders, contact Metav Werkzeuge for precise recommendations and order coordination Technical data SKU: S593-2TM Manufacturer: Teknik Makina Product type: Shank cutter Dimensions & weight Diameter: 16 mm Overall length: 150 mm Shank diameter: 16 mm Cutting length (shank): 40 mm Weight: 0.229 kg Number of cutting edges: 2 Features & compatibility Internal coolant Compatible with R390 11T3 indexable inserts Compatible insert manufacturer: Sandvik Torx key: T8 Fixing screw: M2.5x5.5 eClass: 21180806 FAQ How does the internal coolant work with this cutter? The internal coolant channels deliver cutting fluid directly to the insert edge; the indexable insert shank cutter (SKU S593-2TM) uses this feature to improve chip evacuation and reduce cutting temperatures. Which inserts fit this milling body? This cutter is compatible with R390 11T3 indexable inserts; it is also designed for use with inserts from Sandvik when the correct grade and geometry are selected. What fastening hardware is required for insert clamping? Insert clamping uses a Torx T8 drive and an M2.5x5.5 fixing screw as specified for the cutter body. What applications suit this tool body best? The tool body is intended for CNC milling operations where quick insert changes and coolant-fed cutting are required, offering efficiency for both roughing cycles and finishing passes. Which shank size and holders are required? A 16 mm shank holder or collet is required for correct clamping and minimal run‑out; secure, repeatable clamping improves surface quality and tool life. Manufacturer: Teknik Cutting Tools; Buyukkayacık OSB Mah. 422 Nolu Sokak No: 9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from secure Ø16 mm shank clamping, quick insert changes and compatibility with RPMW 0803 indexable inserts for steady production. Order the tool directly via Metav Werkzeuge or consult the specialist team for application support. Indexable milling cutter R310TM — Ø16 mm shank, for RPMW 0803 inserts (Teknik Makina) The Indexable milling cutter R310TM is a compact indexable tool designed for stable clamping and fast insert replacement in CNC milling applications, suitable for workshops seeking predictable machining cycles. Ø16 mm shank for stable clamping Compatible with RPMW 0803 inserts Two cutting edges for balanced cutting Torx M3x7 fastening, T8 key included Consistent accuracy through stable shank design The combination of a Ø16 mm shank and a compact overall form delivers improved clamping stability, which supports repeatable results on serial runs. With two cutting edges, the tool achieves a balanced cutting action that reduces vibration and improves surface consistency. In practice, indexable systems separate the cutting geometry from the holder: worn edges are replaced rather than the whole tool, which reduces tooling costs and shortens downtime. This makes the cutter a pragmatic choice where predictable cycle times and simplified logistics matter in the production process. Fast insert changes and secure fixation for less downtime Designed for RPMW 0803 indexable inserts, the holder uses a Torx M3x7 screw secured with a T8 key, providing a reliable mechanical clamp for each insert. The insert size reference (RPMW 0803) indicates a standard geometry that many insert manufacturers supply, enabling straightforward reordering. A robust fastening system keeps the insert seated under cutting forces, while the indexable principle allows rapid edge rotation or replacement, turning what would otherwise be maintenance time into a brief shop-floor task and ensuring machines return to operation sooner. Compact length and workshop flexibility With an overall length of 130 mm, the cutter is well suited to confined tool magazines and compact machining centres where tool projection must be managed. The moderate length helps control runout and deflection when used in properly rated toolholders, supporting better tool life and surface finish. The indexable approach also reduces the variety of complete tools that must be stocked: one holder plus a set of inserts covers multiple operations, simplifying procurement and storage for maintenance teams or purchasing departments. Practical handling and maintenance guidance Basic upkeep focuses on correct seating of the insert and periodic check of the Torx screw; the simple Torx interface means replacement requires only a T8 key, which is often retained in the tool cabinet to avoid delays. Visual inspection of the insert seat and screw before a shift helps prevent unset clamps and contributes to consistent process reliability. For higher-volume production, documenting the rotation interval and keeping a controlled insert inventory will help maintain throughput and reduce unexpected machine stops. For tailored recommendations or to discuss suitable insert grades and clamping options, contact Metav Werkzeuge for application support and parts availability via info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists can advise on the optimal setup for specific CNC workflows. Technical Data Article number: R310TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Facts Shank diameter: 16 mm Diameter: 16 mm Overall length: 130 mm Cutting edges: 2 Special features For RPMW 0803 indexable inserts Compatible with Korloy inserts Torx screw: M3x7 Torx key: T8 FAQ What insert type fits this cutter best? The R310TM is designed for RPMW 0803 indexable inserts; matching the insert geometry ensures correct seating and cutting performance. Is a specific insert manufacturer recommended? The tool is compatible with inserts from Korloy; Teknik Makina supplies the holder, and Korloy inserts are a common, compatible choice for RPMW 0803 geometry. What size shank and overall length does the holder have? The holder features a 16 mm shank with an overall length of 130 mm, providing a balance between rigidity and accessibility in compact tool magazines. Which tools are required for insert changes? Insert fixation uses a Torx M3x7 screw and a T8 key, making insert replacement straightforward with standard workshop tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, internal coolant and a compact 16 mm shank to keep machining runs consistent and downtime low; order or request advice via Metav Werkzeuge for tailored integration into existing toolholders. 16 mm shank milling cutter S778-1TM — internal coolant, for XNKU 06T3 indexable inserts A 16 mm shank milling cutter S778-1TM engineered as a cutter body for XNKU 06T3 indexable inserts, providing internal coolant delivery and a 160 mm overall length for versatile milling tasks. Internal coolant for reliable chip evacuation Compatible with Palbit XNKU 06T3 indexable inserts 16 mm shank, 160 mm overall length Supplied with T8 Torx screws M2.5x5.5 Consistent insert performance through targeted cooling The cutter body is designed with an internal coolant channel that directs cutting fluid precisely to the cutting zone, reducing thermal load and helping to extend insert life. Combined with its 16 mm shank, the tool offers a stable connection to standard holders, which reduces run-out and vibration. Compatibility with the XNKU 06T3 family from Palbit ensures rapid insert changes and predictable cutting geometry, translating into reproducible surface finishes and fewer interruptions in production. Efficient material removal with low vibration With 2 cutting edges and a 90 mm cutting length, the tool balances metal removal rate and stability, making it suitable for slotting and light shoulder milling where insert-based systems are preferred. The cutter body’s geometry moderates radial and axial forces, which helps achieve consistent chip formation and lowers the likelihood of chatter. The 160 mm overall length provides reach without excessive overhang, aiding rigidity during deeper passes and improving process reliability. Workshop-friendly assembly and serviceability Fast, secure clamping is provided via the supplied Torx fasteners; use the T8 key and M2.5x5.5 screws for insert retention and replacement. The compact mass (approx. 0.218 kg) and standardised shank diameter make the body easy to handle during tool changes and to integrate into existing tool lists. For traceability and ordering, the cutter is listed under SKU S778-1TM, enabling straightforward stock management and quick replenishment when used in batch production. Ideal applications and professional fit This milling cutter body is suitable for CNC shops, tool rooms and production lines that rely on interchangeable insert systems for flexibility and cost efficiency. The insert-based approach minimises per-part tooling cost while allowing rapid adjustment of cutting geometry. Given its cooling provision and insert compatibility, the tool is particularly useful where controlled temperatures and short changeovers improve throughput and surface quality. For technical availability and selection support for the Teknik Cutting Tools cutter body, contact Metav Werkzeuge for expert advice and fast delivery — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S778-1TM Manufacturer: Teknik Makina Product type: Milling cutter (shank) Compatible inserts: XNKU 06T3 Internal coolant: Yes Core specifications Shank diameter: 16 mm Overall length: 160 mm Cutting length: 90 mm Number of cutting edges: 2 Weight: 0.218 kg Torx key: T8 Torx screw: M2.5x5.5 Materials & features Compatible insert manufacturer: Palbit SKU: S778-1TM ECLASS: 21180806 FAQ Which insert type fits this cutter body? The cutter body accepts XNKU 06T3 indexable inserts; compatibility is specified for Palbit-style inserts, enabling rapid replacement and consistent geometry. Does the tool provide coolant supply to the inserts? Yes, the body is equipped with internal coolant to deliver cutting fluid directly to the cutting edge, improving tool life and chip control. What shank size and lengths are specified? Shank diameter is 16 mm, overall length 160 mm and cutting length 90 mm; these dimensions suit standard 16 mm holders with reasonable reach and rigidity. How are inserts fastened and which tools are required? Inserts are secured with Torx screws M2.5x5.5; a T8 Torx key is recommended for secure and repeatable clamping. What is the SKU for ordering and stock purposes? The product is listed under SKU S778-1TM, which should be quoted for ordering and inventory tracking. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Data inconsistency detected for SKU U104TM: the compatible insert designation is inconsistent — listed as "WCM-0302" and "WCM-0503". This discrepancy could lead to confusion or errors in product usage, inventory management, or customer satisfaction if not addressed promptly, so it is essential to verify the product data thoroughly before publishing to ensure accuracy and prevent potential issues that may arise from conflicting information being presented to end-users or stakeholders who rely on precise and reliable data for decision-making, operational processes, or purchasing decisions.

Data inconsistency: the product is labelled "Vollbohrer" but also specifies compatibility with indexable inserts (SPMG 0602); these entries conflict—please verify and correct the product information, as it is crucial to ensure that the product description accurately reflects its intended use and compatibility to avoid confusion or potential issues for customers who rely on precise specifications when making purchasing decisions, particularly in technical or industrial applications where mismatched components can lead to operational inefficiencies, increased costs, or even safety hazards; therefore, a thorough review of the product details is essential to maintain accuracy and reliability in the provided information.

Take advantage of a compact drill body that pairs precision with economical maintenance: the 16 mm diameter and 64 mm cutting length deliver consistent hole quality while compatibility with SOMT 0502 indexable inserts keeps running costs low. Order directly via Metav Werkzeuge or contact our technical advisors for fitment questions. Vollbohrer — 16 mm indexable-insert drill body by Teknik Makina, compatible with SOMT 0502 The Vollbohrer is a 16 mm drill body designed for indexable inserts, offering stable clamping and a compact overall length for efficient shop-floor machining. 16 mm diameter for precision holes Compatible with Taegutec SOMT 0502 inserts 25 mm shank for secure toolholding 64 mm cutting length for deeper reaches Robust geometry for reproducible hole quality The drill body is built around a straightforward, service-friendly design that prioritises precision and repeatability. With a 16 mm nominal diameter and a 64 mm cutting length, the tool provides sufficient engagement for common through and deep-hole tasks while maintaining concentricity. The 25 mm shank ensures stable clamping in standard holders, reducing run-out and improving surface finish. These measurable attributes translate into fewer scrap parts and a more predictable cycle time on the shop floor. Economical operation through indexable inserts Compatibility with SOMT 0502 indexable inserts (by Taegutec) makes the tool economical in everyday use: worn cutting edges are replaced quickly without discarding the whole tool. The insert system reduces downtime for regrinding and lowers overall tooling expenditure. The indexable insert concept also simplifies inventory management — replacement inserts can be stocked in compact quantities compared with multiple solid drills — and supports consistent cutting geometry across production runs. Compact dimensions that suit diverse spindle setups A total length of 142 mm and a shank length of 56 mm keep the assembly compact while offering sufficient overhang for typical fixture arrangements. The modest mass — 0.322 kg — reduces spindle load and contributes to better dynamic stability at moderate speeds, which benefits surface finish and hole tolerance. These dimensional and weight characteristics make the tool a practical option for smaller machining centres and toolholders that prioritise rigidity. For guaranteed compatibility with Taegutec SOMT 0502 inserts and tailored mounting advice from Metav Werkzeuge, please contact Metav Werkzeuge GmbH by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — assistance on tool selection and adapter options is available Technical Data Article number: U406TM Description: Vollbohrer Manufacturer: Teknik Makina Diameter: 16 mm Overall length: 142 mm Cutting length: 64 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.322 kg Compatible insert: SOMT 0502 Compatible insert manufacturer: Taegutec Intended use: indexable-insert drilling SKU: U406TM FAQ Which insert type fits this drill body? The drill body accepts SOMT 0502 indexable inserts; the product (Teknik Makina Vollbohrer, SKU U406TM) is specified for that insert type and for use with inserts from Taegutec. What are the key dimensions to check for toolholder compatibility? Check the 25 mm shank diameter and the 56 mm shank length when verifying compatibility with a toolholder; these dimensions are listed for the Teknik Makina Vollbohrer (U406TM). How deep can this drill reach effectively? The tool provides a 64 mm cutting length, which indicates the effective depth for cutting engagement; this is suitable for many intermediate-depth drilling operations with indexable inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise holemaking, quick insert replacement and a compact shank for stable clamping — a reliable choice for series production. Order the component directly through Metav Werkzeuge or consult the team for application-specific advice. Indexable Insert Drill U916TM — 16 mm diameter, 25 mm shank (Teknik Makina) The Indexable Insert Drill U916TM is a compact indexable drill body designed for precise holemaking with SPMG 0602 inserts in industrial machining applications 16 mm diameter for standard holemaking Compatible with SPMG 0602 inserts 25 mm shank for secure clamping 32 mm effective cutting length Greater process stability from defined geometry The drill body is engineered around a 16 mm diameter and a 32 mm cutting length, which together provide a predictable machining envelope and reduced deflection during drilling. The term cutting length refers to the portion of the tool that carries the cutting edge; keeping this dimension controlled helps to maintain hole roundness and repeatable tolerances in batch production. The design reduces radial forces and contributes to consistent runout values, which is particularly beneficial when several identical holes are required across multiple workpieces. Fast changeover and lower tooling cost per hole Designed for use with SPMG 0602 indexable inserts, the tool supports quick insert replacement and compatibility with established manufacturers such as Taegutec and YG-1. Using indexable inserts separates the cutting edge life from the drill body life, enabling economical reconditioning: worn inserts are replaced instead of disposing of the whole tool. This arrangement reduces downtime for resharpening and lowers the overall cost per hole in medium-to-high volume production while keeping machining quality consistent. Compact shank and balanced dimensions for reliable clamping A 25 mm shank diameter and 56 mm shank length give the body a solid interface for standard toolholders, supporting stable torque transmission and secure clamping. The 108 mm overall length keeps overhang moderate, helping to limit vibration and maintain surface finish. At 0.275 kg, the component is light enough for convenient handling but rigid enough for automated or manual tool changing systems. Proper clamping of the shank is essential: a secure connection minimises micro-movement and ensures the expected performance from the indexed inserts during drilling cycles. For application-specific recommendations and to secure supply of the Teknik Cutting Tools U916TM Indexable Insert Drill directly from Metav Werkzeuge, contact Metav’s specialists in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and logistical support. Technical data SKU: U916TM Manufacturer: Teknik Makina Core measurements Diameter: 16 mm Overall length: 108 mm Cutting length: 32 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.275 kg Compatibility & special features For indexable inserts SPMG 0602 Compatible with Taegutec and YG-1 inserts Design: indexable insert drill body SKU reference: U916TM FAQ Which inserts fit this drill body? The drill body accepts SPMG 0602 indexable inserts; compatibility with insert suppliers Taegutec and YG-1 is specified for straightforward procurement and interchangeability. What are the main dimensions to check for toolholder compatibility? Key dimensions are the 25 mm shank diameter, 56 mm shank length and the 108 mm overall length; these determine clamping fit and allowable overhang for setup. How long is the effective cutting length? The effective cutting length is 32 mm, which defines the maximum depth of cut the indexed insert can engage while maintaining designed tool stability. Can the tool body be used for automated tool change systems? With a compact form and a 25 mm shank, the U916TM is suitable for many automated tool-change systems where standard shank interfaces are used, provided the holder matches the shank dimensions. How to identify the product in stock lists? The component is listed under SKU U916TM and described as an indexable insert drill for SPMG 0602 inserts by Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of reliable insert compatibility, compact dimensions and reduced downtime for a steady production flow; order the tool via Metav Werkzeuge or consult the technical team for application advice. Vollbohrer – Solid drill, Ø 16 mm, 100 mm overall length (Teknik Makina) A Vollbohrer (solid drill) engineered for metalworking operations, offering indexable-insert compatibility for efficient edge changes and consistent hole quality. Ø 16 mm cutting diameter for standard through-holes 100 mm overall length, 36 mm effective cutting length 20 mm shank diameter, 50 mm shank length Compatible with Korloy indexable insert QC-- 080304 Consistent hole quality with economical insert concept The solid drill is specified for a nominal 16 mm diameter with a 36 mm cutting length, providing a focused cutting zone that supports predictable chip evacuation and steady axial guidance. Designed for use with Korloy indexable plates (type QC-- 080304), the concept allows worn cutting edges to be exchanged rapidly, avoiding long regrinds and lowering per-hole costs. This setup delivers one clear benefit: improved process stability through repeatable hole geometry. Secure clamping and balanced handling A 20 mm shank diameter coupled with a 50 mm shank length ensures firm seating in conventional tool holders and contributes to reduced runout during machining. The 100 mm overall length balances accessibility and rigidity, while the modest mass of about 0.191 kg aids spindle balance and diminishes vibration. As a result, tool life is extended and machining errors from deflection are minimised, which supports steady production output. Designed to keep production moving Built with workshop efficiency in mind, the U036TM from Teknik Makina focuses on fast insert replacement and controlled cutting dynamics, reducing set-up durations and unplanned stops. The geometric choice prioritises chip control and consistent cutting conditions, yielding two clear operational advantages: fewer interruptions and standardised hole tolerances. For manufacturing environments where repeatability matters, this tool offers a pragmatic route to higher throughput. For procurement advice on the Teknik Makina solid drill U036TM or to request a tailored specification check, contact Metav Werkzeuge by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: U036TM Product name: Vollbohrer Manufacturer: Teknik Makina Dimensions & weight Diameter: 16 mm Overall length: 100 mm Cutting length: 36 mm Shank diameter: 20 mm Shank length: 50 mm Weight: 0.191 kg Compatibility & special features Compatible insert manufacturer: Korloy Compatible insert type: QC-- 080304 Files: 62de7dd533927e49dbf32721, 62de7ec10f56dbb4de4dbf2c FAQ What insert type fits this drill? The drill accepts Korloy indexable plates of type QC-- 080304, enabling simple edge replacement without full tool change. What are the key dimensions to check for holder compatibility? Verify the 20 mm shank diameter and 50 mm shank length when selecting a collet or holder for the tool U036TM to ensure secure clamping. Is the cutting length sufficient for through-hole work? With a 36 mm cutting length and a 100 mm overall length, the geometry is intended for typical through-hole and short-reach drilling tasks requiring controlled chip evacuation. How does the insert concept affect maintenance? Using indexable plates (QC-- 080304) reduces downtime because worn edges are exchanged rapidly; this approach lowers per-cutting-edge costs and simplifies maintenance routines. Which brand manufactures this tool? The tool is produced by Teknik Makina and listed under SKU U036TM for straightforward identification in procurement and inventory systems. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, insert‑based milling solution that combines a 16 mm shank with a 60 mm cutting length for stable, repeatable machining; order the cutter directly via Metav Werkzeuge or consult the technical team for application advice. S216TM shank cutter – for APKT 0903 indexable inserts, 90° cut angle (Teknik Cutting Tools) The S216TM shank cutter is a shank-mounted milling tool designed for use with APKT 0903 indexable inserts, offering compact dimensions and a right‑angled cutting geometry for efficient shoulder and face milling in workshop and production environments For APKT 0903 indexable inserts 16 mm shank diameter 60 mm cutting length 90° cut angle for shoulder milling Torx screw M2.5x5.5, T8 key Predictable performance with insert-based machining The S216TM is engineered for indexable insert workflows, converting the repeatability of replaceable tips into measurable productivity gains. The combination of a 16 mm shank and a 60 mm cutting length gives a compact, rigid tool geometry that reduces deflection in short‑reach milling operations. A 90° cut angle produces true shoulder faces, which simplifies finishing passes and can lower cycle time by reducing the need for secondary operations. For manufacturers focused on predictable throughput, the tool’s dimensions support stable feeds and speeds in standard setups. fast insert changes and secure clamping to cut downtime Insert retention is solved with a Torx screw M2.5x5.5 that is driven with a T8 key, providing a secure, repeatable clamp for APKT pads. The small, robust fastening method makes indexable insert replacement quick and reliable, keeping maintenance time to a minimum. Compatibility with recognised insert suppliers such as Walter ensures widely available cutting grades and geometries, so tooling families can be standardised across the shop. Lightweight construction (approx. 0.34 kg) and balanced geometry assist in maintaining tool life and spindle load consistency. Compact versatility for workshop and production milling This shank-mounted cutter is suitable where a compact holder is required without sacrificing the benefits of indexable tooling. The two‑edge configuration gives an efficient cut pattern for light to medium material removal in general steel and similar workpieces when using appropriate APKT 0903 grades. The straightforward design eases tool management: spare inserts, fastening screws and a single key size streamline inventory and operator training. Supplied data such as shaft and overall lengths allow process planners to integrate the tool into fixture and tool‑changer layouts with confidence. For availability and specification checks for the Teknik Cutting Tools S216TM, contact Metav Werkzeuge for stock and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S216TM Manufacturer: Teknik Makina Designation: Schaftfräser Application: for APKT 0903 Indexable Inserts ECLASS: 21180806 ETIM: EC011860 Facts Shank diameter: 16 mm Cutting length: 60 mm Diameter: 16 mm Overall length: 200 mm Number of cutting edges: 2 Cut angle: 90° Weight: 0.34 kg Torx screw: M2,5x5,5 Torx key: T8 Special features Compatible with APKT 0903 indexable inserts Recommended insert brand: Walter Shank-mounted design for rigid clamping Two cutting edges for efficient material removal FAQ Which indexable inserts fit this cutter? The cutter accepts APKT 0903 indexable inserts; insert grades from Walter are suitable and commonly used with the S216TM. What are the key dimensions to check for machine integration? Important dimensions are the 16 mm shank, 60 mm cutting length and 200 mm overall length; these figures should be checked against toolholder clearance and tool‑changer capacity. How is the insert secured and what tool is required? Inserts are clamped with a Torx screw M2.5x5.5; a T8 key is used to tighten and release the screw. Is the S216TM suitable for shoulder and face milling? Yes. The 90° cut angle and two‑edge geometry make the tool appropriate for shoulder and light face milling tasks when paired with the correct APKT 0903 grade. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise holemaking with a Ø 16 mm cutting diameter, a 25 mm shank for secure clamping and a 48 mm cutting length for deeper holes; the combination supports consistent cycle times and easy insert changes. Order the solid drill directly via Metav Werkzeuge or ask our consultants for application advice. Solid drill U143TM (indexable-insert drill) by Teknik Makina — Ø 16 mm, 25 mm shank The Solid drill U143TM is an indexable-insert drilling tool designed for demanding CNC holemaking where repeatability and quick insert changes are required Ø 16 mm cutting diameter 25 mm shank for secure clamping 48 mm cutting length for deeper holes Compatible with Korloy WCM inserts High-performance drilling with measurable stability The U143TM is engineered to deliver precise holemaking through a combination of a rigid body and a substantial 25 mm shank, which reduces deflection under load and ensures repeatable positioning in the spindle. The 48 mm cutting length allows longer engagement than standard short drills, enabling deeper passes without sacrificing stability. The result is a measurable improvement in hole roundness and positional accuracy, particularly on automated CNC centres where tool retention and concentricity determine process quality. Practical benefits in workshop and production use Designed as an indexable-insert solution, this solid drill shortens downtime: worn cutting edges are replaced by changing the insert rather than regrinding a solid tip. Compatibility with Korloy WCM inserts provides access to a wide portfolio of grades and geometries, allowing process optimisation for different workpiece materials and cutting conditions. The drill’s overall length 124 mm and balanced mass help maintain consistent cutting forces, so setup and cycle planning become more predictable for production technicians and planners. Integration, handling and maintenance explained The tool’s compact weight (0.307 kg) and defined clamping length (56 mm) simplify handling and storage, and the solid construction minimises vibration that can reduce insert life. Insert seating and clamping torque are decisive for performance; following the insert manufacturer’s instructions ensures secure seating and repeatable cuts. For workshop managers looking to reduce tooling complexity, the indexable design delivers cost-effective edge renewal and easier inventory management compared with brazed or solid-tip solutions. For reliable, repeatable holemaking with Teknik Makina engineering, contact Metav Werkzeuge for tailored technical advice and fast delivery from Emmerich. Technical data Article number: U143TM Manufacturer: Teknik Makina Designation: Solid drill Compatible inserts: Korloy WCM series Measurements Diameter: 16 mm Overall length: 124 mm Cutting length: 48 mm Shank diameter: 25 mm Clamping length: 56 mm Weight: 0.307 kg Features For indexable inserts (WCM) Designed for secure clamping Solid-body construction Suitable for CNC drilling operations FAQ Which insert types are compatible with this drill? The solid drill U143TM is intended for use with Korloy WCM series indexable inserts; confirm the exact insert geometry and grade to match the specific machining task. What dimensions should be checked before mounting? Check the toolholder clamping interface and ensure the 25 mm shank, overall length 124 mm and the clamping length of 56 mm fit the spindle or holder to maintain concentricity. Can this tool be used for deeper-hole operations? With a 48 mm cutting length and a rigid solid body, the drill supports deeper holemaking within the limits of its geometry and the machine setup; process parameters should be adapted accordingly. How are worn cutting edges replaced? Worn edges are renewed by replacing the indexable insert; follow the insert manufacturer’s torque specifications for secure seating and consistent performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust solid drill that combines precise indexable-insert compatibility with reliable reach and clamping security — ideal for consistent holemaking in small-batch and production environments. Order directly via Metav Werkzeuge or ask the consultants for specification checks and availability. Vollbohrer U776TM — Solid drill for indexable inserts, Ø 16 mm, Korloy-compatible A Vollbohrer U776TM engineered for dependable drilling with Korloy indexable inserts in CNC turning and milling operations Compatible with Korloy WCM-0302 inserts 16 mm cutting diameter 80 mm effective cutting length 25 mm shank for secure clamping Maximise machining flexibility with proven insert compatibility The U776TM is built for indexable-insert drilling, providing the economic and operational advantages associated with removable carbide inserts. Acceptance of Korloy WCM-0302 inserts reduces tool-change downtime and allows specific insert grades to be selected for different workpiece materials. With a nominal 16 mm diameter, the tool is suited to common drilling cycles on CNC lathes and machining centres, enabling quick adaptation between roughing and finishing passes when paired with the correct insert geometry and feed settings. Consistent hole quality through controlled geometry and reach A generous 80 mm cutting length combined with an overall length of 156 mm gives extended reach without sacrificing stability, while the 25 mm shank diameter supports secure clamping in standard toolholders. This balance of reach and rigidity promotes repeatability in hole diameter and surface finish, reducing downstream rework. The tool’s layout is optimised to keep radial runout low, with the effective cutting length matched to insert size to preserve cutting edge life and hole tolerances over extended runs. Streamlined integration for workshop efficiency At just 0.378 kg, the tool is light enough for fast handling yet designed to withstand the forces of routine production drilling. As a solid drill for indexable inserts, it reduces consumable costs compared with one-piece solid-carbide cutters, since only the inserts require replacement. The construction supports common clamping systems and is suitable for serial operations where tool change speed and predictable performance underpin productivity gains. For complex applications or bespoke insert grades, the technical data can be reviewed to confirm suitability for particular machining strategies. Contact Metav Werkzeuge for tailored technical advice and to confirm availability of the U776TM solid drill compatible with Korloy WCM-0302 inserts: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: U776TM Manufacturer: Teknik Makina Product: Vollbohrer Dimensions & weight Diameter: 16 mm Overall length: 156 mm Cutting length: 80 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.378 kg Compatibility & features Compatible with Korloy WCM-0302 inserts Insert manufacturer: Korloy Product type: Solid drill for indexable inserts SKU: U776TM FAQ Which insert type fits this solid drill? The U776TM is specified for use with Korloy WCM-0302 indexable inserts and is designed to accept those grade and geometry variants. What drilling depth is achievable with this tool? The tool provides an effective cutting length of 80 mm, with an overall length of 156 mm, defining the practical drilling reach for through and blind-hole operations. Which machines suit the U776TM? This solid drill is suitable for CNC turning centres and machining centres where a 25 mm shank can be securely clamped for stable drilling cycles. Is high-speed machining supported? A dedicated high-speed rating is not listed in the available product data for the U776TM; selection of spindle speed and feeds should follow insert manufacturer guidance. Are material application details provided? Material suitability is not specified in the supplied product fields for the U776TM; consult Korloy insert datasheets or technical specifications for recommended workpiece materials. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable solution that combines rapid insert changes and stable clamping for predictable hole quality; the 16 mm diameter, 86 mm overall length and 36 mm cutting length ensure consistent cycle times while keeping tool handling light. Order via Metav Werkzeuge for dependable supply from Emmerich or consult the technical team for application support. 16 mm Solid Drill U064TM for XC-- 080304 Indexable Inserts — 86 mm overall length, Teknik Makina The U064TM solid drill is a compact drill body designed for precision drilling with XC-- 080304 indexable inserts, intended for workshop and light production environments where quick insert changes and repeatable hole geometry are required. Compatible with Ceratizit XC-- 080304 inserts 16 mm diameter for consistent hole quality 86 mm overall length, 36 mm cutting length Secure clamping with T8 Torx, M3x7 screws Faster throughput with indexable tooling and minimal downtime The combination of an indexable inserts system and a compact drill body reduces machine downtime: worn cutting edges are replaced in seconds instead of resharpening whole tools. With a nominal 16 mm diameter and 36 mm cutting length inside an 86 mm body, this configuration supports short set-up times and steady cycle rates. The lightweight construction (approx. 0.191 kg) simplifies handling at the tool change trolley and contributes to lower spindle load during short-cycle drilling tasks. Robust clamping for repeatable hole tolerances Clamping integrity is central to repeatable accuracy. The drill uses T8 Torx engagement and M3x7 screws to secure the cutting head, delivering stable axial alignment and reduced run-out compared with non-indexable heads. A 50 mm tool shank length increases stiffness in typical holder arrangements, which helps to maintain concentricity and surface finish. These features translate into fewer rejects and more reliable batch processing. Integrates easily into existing insert inventories Designed for use with Ceratizit indexable inserts (type XC-- 080304), the tool lets workshops consolidate their cutting edge stock and benefit from established insert grades and geometries without changing holders. The compact drill form suits both single-spindle and multi-spindle setups, enabling straightforward retrofit into established tool lists. Consistent mechanical interfaces simplify planning and reduce the variety of specialised solid drills required. Low-maintenance handling and predictable service intervals Indexable systems are inherently service-friendly: only the insert and fastening screw are cycled during maintenance, keeping spare parts inventories small and predictable. The secure Torx screw fixation ensures consistent clamping torque when using the specified T8 key, reducing assembly errors and preserving insert life. For production planners this means predictable tool life, simpler replenishment and fewer unscheduled interventions on the machine. Speak to Metav Werkzeuge for tailored tooling advice and reliable supply from our Emmerich stock; request technical data or a quote for the Teknik Makina U064TM solid drill via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: U064TM Label: 16mm Vollbohrer XC-- 080304 L86mm Manufacturer: Teknik Makina Product type: Solid drill Bezeichnung (designation): Vollbohrer for XC-- 080304 Indexable Inserts UID: U064TM Facts Diameter: 16 mm Overall length: 86 mm Cutting length: 36 mm Shank length: 50 mm Weight: 0.191 kg ECLASS: 21180201 Special features Compatible inserts: XC-- 080304 Compatible insert manufacturer: Ceratizit Torx key: T8 Torx screw: M3x7 FAQ Which inserts fit this drill? The drill is designed for XC-- 080304 indexable inserts and is compatible with inserts from Ceratizit when used with the specified clamping screws. What are the key dimensions for set-up planning? Key dimensions are 16 mm diameter, 36 mm cutting length and 86 mm overall length; shank engagement is 50 mm. How is the cutting head secured? The cutting head is fixed using a T8 Torx engagement and M3x7 screw to ensure reliable clamping during drilling cycles. Is the tool suitable for multi-spindle production machines? Yes — the compact form factor and standardised insert interface make it suitable for integration into multi-spindle arrangements and automated tool magazines. What weight should be considered for handling and balancing? The tool weighs approximately 0.191 kg, a characteristic that helps reduce spindle inertia for short-cycle operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact drilling solution that pairs 16 mm cutting diameter with reliable indexable inserts for predictable production cycles; the combination of a 36 mm cutting length and a 50 mm shank ensures stable clamping and reduced downtime. Order or request stock information directly via Metav Werkzeuge for rapid delivery and expert advice. Indexable Drill Body for XC-- 080304 Indexable Inserts, 16 mm (Teknik Makina) Indexable Drill Body designed for secure, repeatable drilling in CNC and industrial metalworking, compatible with XC-- 080304 indexable inserts for fast insert changes and consistent hole quality 16 mm cutting diameter Designed for XC-- 080304 inserts Total length 86 mm Compatible with ISCAR inserts Faster metal removal through replaceable inserts The indexable drill body is engineered to accelerate cycle times by using XC-- 080304 indexable inserts that can be changed quickly without regrinding. The tool’s 36 mm cutting length provides a robust engagement zone, which reduces the number of passes required for many drilling tasks and improves throughput. By separating the body from the cutting edges, maintenance becomes a straightforward swap of worn inserts rather than full tool replacement, lowering tool inventory costs and shortening production interruptions. The result is reliable, measurable productivity gains on multi-shift operations. Stable clamping and machine compatibility for consistent holes A secure connection between toolholder and spindle is essential for repeatable hole quality; the body’s 50 mm shank and 86 mm overall length deliver the required reach while maintaining rigidity for the drilling operation. The design accommodates the recommended T8 Torx key and M3x7 Torx screw specification for insert fastening, ensuring straightforward assembly and a defined torque interface for repeatable clamp force. Compatibility with ISCAR insert systems supports integration into existing tool inventories and reduces the need for adapter components, minimising set-up time and variance between tool changes. Practical workshop benefits that reduce downtime Serviceability is a key advantage: the modular arrangement allows fast insert replacement and simple inventory management, which translates into less machine idle time and a cleaner cost-per-hole calculation. The tool body’s moderate mass (approx. 0.191 kg) contributes to lower dynamic loads on the spindle during operation, while its standardised interface helps maintain tool balance and extend insert life. For workshops seeking dependable results without complex upkeep, this approach converts technical simplicity into everyday reliability. Designed for production environments and straightforward logistics Manufactured by Teknik Makina, the component is labelled for clear identification (SKU U048TM) and fits directly into established insert cycles. The standardised form factor supports automated tool change systems and manual toolrooms alike, making it appropriate for both OEM production lines and jobbing shops. By combining standard inserts with a robust body, the solution offers a balance between flexibility and repeatability — suitable wherever stable hole tolerances and fast reconditioning are priorities. Contact Metav Werkzeuge for availability and technical consultation on Teknik Makina indexable drill bodies and compatible XC-- 080304 insert systems via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: U048TM Label: 16mm indexable drill XC-- 080304 L86mm Manufacturer: Teknik Makina Product type: Indexable drill body eClass: 21180201 Facts Diameter: 16 mm Overall length: 86 mm Cutting length: 36 mm Shank length: 50 mm Weight: 0.191 kg Special features For XC-- 080304 indexable inserts Compatible with ISCAR insert systems Torx key: T8 Torx screw: M3x7 SKU reference: U048TM FAQ Which inserts fit this drill body? The drill body accepts XC-- 080304 indexable inserts; it is designed for the insert geometry specified by that reference and fastens with the supplied M3x7 Torx screw. Is this component compatible with ISCAR systems? Yes, the body is compatible with ISCAR inserts as noted; compatibility allows integration into tool assemblies that already use ISCAR indexable cutters. What are the key dimensions for set-up and reach? Key dimensions: 16 mm cutting diameter, 36 mm cutting length, 50 mm shank length and 86 mm overall length — useful for fixture planning and toolholder selection. What fastening tools are required for insert changes? Insert fastening uses a T8 Torx key and the specified M3x7 Torx screw for secure, repeatable clamping of the inserts. How is the tool identified for reordering or stock control? Reference SKU U048TM and the label "16mm indexable drill XC-- 080304 L86mm" for precise reordering and stock management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise Ø 16 mm cutting, a 36 mm cutting length and a compact 86 mm overall body that improves access in confined toolpaths; the compatible indexable insert system reduces downtime and simplifies regrinding logistics. Order the solid drill for XC‑080304 indexable inserts directly via Metav Werkzeuge or ask our consultants if needed Solid drill U22TM – 16 mm, for XC‑080304 indexable inserts (Teknik Makina) Solid drill U22TM for machining operations with indexable inserts, offering a compact overall length and a focused cutting zone for reliable holemaking in production and repair work 16 mm nominal diameter Compatible with XC‑080304 indexable inserts 36 mm cutting length for deep engagement 50 mm shank length for secure clamping Consistent cutting performance for repeatable holes The drill body is engineered to provide stable machining when fitted with XC‑080304 indexable inserts. With a 16 mm diameter and a 36 mm cutting length, the design concentrates cutting forces inside the insert pocket, reducing deflection and improving roundness in bore production. The combination of a short, rigid body and the indexable insert system delivers predictable tool life and simpler maintenance compared with multi-tooth solid cutters, making the tool suited to batch production and repair tasks where consistent tolerance is essential. Quick insert changes and secure retention reduce downtime Tool change efficiency is built in: the interface accepts inserts from Taegutec and secures them with an M3x7 screw tightened using a T8 Torx key. This standardised fastening enables safe and fast insert replacement without regrinding whole tools, cutting setup time and inventory complexity. The 50 mm shank length provides reliable clamping engagement in standard holders, improving concentricity and making the tool compatible with common toolholders used in turning and drilling centres. Compact form and practical workshop advantages An overall length of 86 mm keeps the tool compact where reach is limited while the 20 mm holder diameter supports robust mounting in tool posts and adaptors. At approximately 0.191 kg, the body balances rigidity with manageable handling during setup. The solid body concept with indexable geometry is particularly useful for operations that demand frequent edge changes or where different grades of inserts are used for varying materials; it permits simple optimisation of cutting grades without replacing the entire tool body. For advice on selecting the correct insert grade or for ordering the Teknik Makina solid drill U22TM via Metav Werkzeuge, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for personalised support Technical data Article number: U22TM SKU: U22TM UID: U22TM Designation: Solid drill Secondary designation: for XC-- 080304 Indexable Inserts Manufacturer: Teknik Makina Facts Diameter: 16 mm Overall length: 86 mm Cutting length: 36 mm Shank length (holder engagement): 50 mm Holder diameter: 20 mm Weight: 0.191 kg eClass: 21180201 Special features Compatible inserts: XC‑080304 Compatible insert manufacturer: Taegutec Fastening screw: M3x7 Torx key: T8 Product type: Solid drill Label: 16mm Vollbohrer XC-- 080304 L86mm FAQ Which insert type fits this drill body? The drill body is designed for XC‑080304 indexable inserts, which are fitted and secured in the pocket using the M3x7 screw on the U22TM tool. What are the key dimensions to check for toolholder compatibility? Check the 20 mm holder diameter and the 50 mm shank engagement length; these dimensions ensure proper clamping and concentricity for the U22TM solid drill. Which insert manufacturer is recommended for this body? This body is specified as compatible with Taegutec inserts; using the recommended inserts maintains the intended tool performance and serviceability. How does the fastening work for the insert? Inserts are clamped with an M3x7 screw that is tightened with a T8 Torx key, enabling fast and reliable changeovers on the U22TM drill body. Is this tool suitable for tight-access applications? Yes; the compact 86 mm overall length reduces overhang and helps achieve better rigidity and access in confined machining set-ups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a combination of efficient indexable-insert milling, internal coolant and a rigid 16 mm shank for consistent chip evacuation and prolonged tool life. Order the shank cutter directly via Metav Werkzeuge or ask our consultants if additional technical data is required. Shank cutter S766-2TM — 16 mm shank, internal coolant (Teknik Makina) The Shank cutter S766-2TM is an insert milling tool designed for economical and flexible metal removal with APKT 1003 indexable inserts across a range of workshop and light industrial milling tasks 16 mm shank diameter Internal coolant for tool cooling Compatible with APKT 1003 inserts Two cutting edges for efficient milling Faster material removal with indexable inserts and low tooling cost The design accepts APKT 1003 indexable inserts, a common and economical choice for many milling operations. Using replaceable indexable inserts reduces tooling cost per part since only the insert is replaced when worn; the body remains in service. The two cutting edges enable stable engagement and efficient chip sectioning, which contributes to higher metal removal rates and predictable cycle times. This approach suits production runs where rapid insert changes and consistent cutting forces matter. Controlled cooling and improved tool life for demanding passes Equipped with internal coolant, the cutter directs coolant close to the cutting zone to improve heat dissipation and chip flushing. Cooler cutting temperatures reduce insert wear and help maintain edge integrity over longer periods, which increases process reliability. The internal coolant feature is particularly beneficial when machining alloys or performing interrupted cuts where heat buildup and chip evacuation influence surface finish and dimensional stability. Rigid dimensions for repeatable setups and stable machining With a 16 mm shank, an overall length of 150 mm and an 80 mm cutting length, the tool balances reach and stiffness for many workshop setups. The defined shank diameter and length support repeatable clamping and reduced deflection, which is essential when maintaining tight tolerances. The documented weight of 0.121 kg contributes to predictable toolholder dynamics and makes balancing straightforward in small- to medium-sized milling machines. Simple maintenance and secure insert fastening for uninterrupted work Insert retention uses an accessible Torx system with a T8 key and M2.5x5.5 Torx screw, allowing quick insert changes and secure clamping. The compatibility with Palbit-manufactured inserts ensures broad availability of grades and geometries for different materials. Routine service is straightforward: clean coolant passages, inspect seats, and replace inserts as needed to keep the cutter delivering consistent performance. For application-specific recommendations and grade selection, Metav’s consultants are available to advise on the optimal insert and coolant strategy. For detailed application guidance or supply from stock, contact Metav Werkzeuge for tailored advice and efficient delivery from Emmerich. Technical data SKU: S766-2TM Manufacturer: Teknik Cutting Tools / Teknik Makina Product type: Shank cutter Compatible inserts: APKT 1003 Compatible insert manufacturer: Palbit Core data Diameter: 16 mm Overall length: 150 mm Shank diameter: 16 mm Cutting length: 80 mm Cutting edges: 2 Weight: 0.121 kg Torx screw: M2.5x5.5 Torx key: T8 Special features Internal coolant For APKT 1003 indexable inserts Compatibility with Palbit inserts Insert-retained milling design FAQ Is the cutter compatible with APKT 1003 inserts? Yes. The S766-2TM is designed specifically for APKT 1003 indexable inserts and accepts inserts from Palbit as specified by the tool design. Does the tool provide internal coolant supply? Yes. The cutter features internal coolant, which improves cooling at the cutting edge and aids chip evacuation during milling. What are the shank and overall dimensions? The tool has a 16 mm shank diameter, an overall length of 150 mm and an 80 mm cutting length as stated for the S766-2TM. How are inserts fastened and changed? Inserts are secured with a Torx screw (size M2.5x5.5) using a T8 Torx key, enabling fast and secure insert replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine rigid clamping and controlled cooling for consistent milling results with indexable inserts; the tool pairs a 16 mm shank with internal coolant and a 25 mm effective cutting length. Order the shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shank milling cutter for APMT 0602 indexable inserts — internal coolant, 16 mm shank (Teknik Makina) The Shank milling cutter for APMT 0602 indexable inserts provides stable, insert-based milling for general workshop and light industrial applications in a compact L90 mm design. 16 mm shank for rigid clamping Internal coolant for effective cooling Compatible with APMT 0602 Korloy inserts L90 mm total length, 25 mm cutting length Consistent cutting performance with indexable inserts The cutter is built for reliable machining of parts where repeatability matters. By accepting APMT 0602 inserts from Korloy, the tool enables quick index changes and predictable cutting geometry. The integrated internal coolant supplies lubricant and cooling directly to the cutting zone, which improves chip evacuation and reduces thermal load on the insert. The 16 mm shank ensures secure clamping in common toolholders, limiting run-out and vibration for a steadier surface finish and fewer rejected parts. Reduced downtime through easy insert maintenance Maintenance and on-machine service are straightforward thanks to the simple fixing concept. The design uses a Torx retention system; the required key is T6 and the insert screw specification is M1.8×4.1, allowing fast replacement cycles with standard workshop tools. With four cutting edges available per head and a 25 mm cutting length, the tool is suitable for medium-depth milling tasks while supporting predictable index intervals. The compact L90 mm overall length balances accessibility and rigidity to keep changeovers brief and tool life consistent. Seamless integration into production workflows This tooling solution is practical for mixed-production environments that favour insert systems for flexibility. The cutter is listed under SKU S005-1TM and is manufactured by Teknik Cutting Tools, making it straightforward to match with existing holders and ordering systems. The modest mass and standard shank diameter simplify handling and inventory. Combined with a supplier that offers specialist advice and reliable logistics, the tool helps maintain continuous operation and simplifies replacement planning. Discuss application-specific planning and availability with Metav Werkzeuge in Emmerich; request stock details or compatibility advice for the Teknik Cutting Tools S005-1TM shank milling cutter with internal coolant via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S005-1TM Brand: Teknik Makina Product type: Shank milling cutter Compatible inserts: APMT 0602 (Korloy) Internal coolant: Yes Weight: 0.121 kg Core dimensions Shank diameter: 16 mm Total length: 90 mm Cutting length: 25 mm Number of cutting edges: 4 Materials & special features Insert screw: Torx T6, M1.8×4.1 Suitable for Korloy APMT 0602 inserts Label: 16mm Schaftfräser APMT 0602 L90mm mit Innenkühlung eClass: 21180806 FAQ Which insert type fits this cutter? The shank milling cutter accepts APMT 0602 indexable inserts; it is designed to work with Korloy APMT 0602 inserts for straightforward interchangeability. Does the tool provide internal coolant? Yes, the cutter features internal coolant to deliver fluid to the cutting edge, aiding chip evacuation and thermal control during milling. What shank size and holder compatibility are required? A 16 mm shank diameter is specified; holders and collets must accommodate a 16 mm shank for correct clamping and concentricity. Which key and screw are used for insert changes? Insert retention uses a Torx T6 key and screw sized M1.8×4.1, permitting rapid and standardised insert replacement. For which machining tasks is this cutter suitable? The cutter suits general milling operations where indexable inserts are preferred, offering a 25 mm cutting length and four cutting edges for medium-depth passes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, service-friendly tool that combines internal coolant delivery, a 16 mm shank and compatibility with APMT 0602 indexable inserts for stable machining and reduced downtime; order directly via Metav Werkzeuge or consult our specialists for application advice. Insert milling cutter for APMT 0602 indexable inserts — 16 mm shank, internal coolant (Teknik Makina) Insert milling cutter for APMT 0602 indexable inserts designed for reliable medium-duty milling in production and workshop environments 16 mm shank diameter Internal coolant supply Designed for APMT 0602 indexable inserts 120 mm overall length Improved chip control and consistent tool life The tool is built around an internal coolant channel that directs cutting fluid straight to the cutting zone, reducing heat and improving chip evacuation; this results in longer insert life and more consistent surface quality. With a 16 mm shank and a compact 120 mm overall length, the cutter supports stable clamping in standard collets and holders, which helps to decrease vibration and enhances repeatability in serial production. The use of indexable inserts means maintenance is limited to periodic insert replacement rather than full-tool resharpening, improving uptime and lowering running costs. Fast insert changes and secure fixing for short set-up times The cutter accepts APMT 0602 indexable inserts, secured with a Torx T6 screw (M1.8x4.1), enabling quick, repeatable insert changes with common workshop tools. The configuration with 4 cutting edges provides balanced cutting action and smoother load distribution across the tool body, which supports higher feed rates under stable conditions. Clear, standardised fixing parts mean spares and replacement inserts from established suppliers such as Korloy can be fitted without modification, simplifying supply-chain management and reducing tool-change errors. Practical design for everyday production use A modest 25 mm cutting length offers a compromise between reach and rigidity, suitable for pocketing and shoulder milling where stiffness and accessibility are required. The tool’s design focuses on straightforward integration into existing toolsets: compact dimensions, standardised connection interfaces and a measurable weight that supports predictable toolholder dynamics. For machining operations where efficient cooling and straightforward maintenance are priorities, this indexable-insert cutter delivers a balance of performance and serviceability tailored to busy workshops and industrial settings. Speak with Metav Werkzeuge for tailored application support on Teknik Makina’s insert milling solutions and to confirm suitability for specific production tasks — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: S029-1TM Manufacturer: Teknik Makina Product type: Insert milling cutter Designation: Shaft milling cutter for APMT 0602 indexable inserts Facts Shank diameter: 16 mm Overall length: 120 mm Cutting length (shank length of cut): 25 mm Number of cutting edges: 4 Weight: 0.164 kg eClass: 21180806 Special features Internal coolant supply Compatible with APMT 0602 indexable inserts Compatible insert manufacturer: Korloy Torx key size: T6 Torx screw: M1.8x4.1 FAQ Which inserts fit this milling cutter? The cutter is designed for APMT 0602 indexable inserts; Korloy inserts in this designation are compatible with the clamping system of the S029-1TM. Does the tool offer coolant to the cutting zone? Yes, the S029-1TM features internal coolant delivery to support cooling and chip evacuation directly at the cutting edge. What are the main dimensions to consider when selecting a holder? Key dimensions are a 16 mm shank diameter, 120 mm overall length and 25 mm cutting length, which help determine suitable collets and toolholders. How are the inserts secured and what tools are needed? Inserts are fixed with a Torx screw (M1.8x4.1); a Torx T6 key is required to tighten and remove the screw. Is this cutter suitable for high-volume shop-floor use? The S029-1TM is designed with serviceability and repeatability in mind, offering quick insert changes and internal coolant for consistent performance in regular production environments. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust combination of precise toolholding and quick insert changes: the 16 mm shank and 70 mm cutting length ensure stable deep cuts, while compatibility with APXT 1003 indexable inserts reduces downtime and tooling costs. Order directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter S190TM – for APXT 1003 indexable inserts, Ø16 mm, 2 cutting edges (Teknik Makina) The Shank milling cutter S190TM is a shank-mounted milling body engineered for secure, repeatable milling with APXT 1003 indexable inserts, designed for workshop and light industrial milling tasks where fast insert changes and consistent results are required. Ø16 mm shank for stable toolholding 70 mm cutting length for deeper passes Compatible with APXT 1003 inserts (Korloy) Secured with M2.5x5.5 Torx screw, T8 key Stable geometry for predictable metal removal The central design focus is consistent, vibration‑resistant performance during milling operations. With a 16 mm shank and an overall length of 250 mm, the tool body provides solid clamping and run‑out control that supports repeatable machining. The 70 mm cutting length gives scope for deeper engagement while the two cutting edges balance material removal rate and surface finish. The specified 90° cutting angle suits face and peripheral milling tasks, offering a straightforward approach to slotting and shoulder work without complex setup changes. Quick insert handling and economical downtime reduction Tooling efficiency is achieved through the use of APXT 1003 indexable inserts, a standard size that simplifies inventory management. The cutting edge geometry on these inserts is easily indexed or replaced, which reduces tool change time and overall production downtime. The cutter is fastened with an M2.5x5.5 Torx screw operated with a T8 key, enabling secure clamp‑up and quick servicing at the machine. For operations that value throughput and predictable consumable costs, this arrangement delivers a clear cost‑benefit through lower per‑cut tooling expense and simplified reconditioning. Compatibility and workshop advantages Compatibility with Korloy manufactured inserts and the standard APXT 1003 system makes the cutter a flexible component for existing insert stocks and procurement workflows. The body’s nominal 16 mm diameter and balanced weight of 0.415 kg keep handling straightforward while supporting a steady centre of gravity in the spindle. For shops converting from solid tool solutions to insert systems, this shanked cutter offers a pragmatic route to faster changeovers and improved process control, without extensive retrofitting. Technical staff will appreciate the clear specification set for integration into existing tool lists and CAM setups. For tailored technical guidance or to source the S190TM directly from Metav Werkzeuge, contact our Emmerich‑based specialists by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data Article number: S190TM Name: Shank milling cutter for APXT 1003 indexable inserts Manufacturer: Teknik Cutting Tools / Teknik Makina Facts Shank diameter: 16 mm Cutting length: 70 mm Diameter: 16 mm Overall length: 250 mm Cutting edges: 2 Weight: 0.415 kg Cutting angle: 90° Special features For APXT 1003 indexable inserts Compatible with Korloy inserts Torx screw: M2.5x5.5 Torx key: T8 FAQ Which insert type fits this milling cutter? The cutter accepts APXT 1003 indexable inserts; the specification on the S190TM is matched to that insert format for secure seating and correct cutting geometry. Is the S190TM compatible with Korloy inserts? Yes, the product is specified as compatible with Korloy APXT 1003 inserts, enabling use of widely available insert options. How is the insert secured in the cutter body? Inserts are clamped and secured with an M2.5x5.5 Torx screw, tightened using a T8 key, providing firm retention and straightforward replacement. What are the main dimensions to consider when setting up the tool? Key dimensions are a 16 mm shank diameter, 70 mm cutting length and an overall length of 250 mm, which should be considered for tool projection and machine spindle clearance. Can the cutter be used for both face and peripheral milling? Yes, the 90° cutting angle and the two cutting edges make the tool suitable for both face and peripheral milling tasks where indexable inserts are preferred. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid 16 mm shank, integrated internal coolant and compatibility with LNMX 0603 indexable inserts for reliable chip control and consistent cycle times. Order the shank milling cutter directly via Metav Werkzeuge or request advice from our consultants for application-specific selection. Shank milling cutter S284-1TM — 16 mm shank, internal coolant (Teknik Makina) Shank milling cutter S284-1TM engineered for indexable milling with LNMX 0603 inserts, offering a compact tool body for stable, repeatable machining in small to medium cutters. 16 mm shank diameter for rigid clamping Integrated internal coolant for chip evacuation Compatible with LNMX 0603 inserts (Korloy) Torx T8 screw M3x7 for secure insert retention Higher throughput from a compact, rigid design The combination of a 16 mm shank and a hardened tool body delivers improved rigidity and vibration resistance, which translates directly into more reliable surface finish and longer insert life. For short to medium overhangs the compact geometry reduces bending moments and enables higher metal removal rates compared with non-shank tooling of the same diameter. Built for indexable milling, the tool accepts LNMX 0603 inserts, allowing rapid insert changes and minimal downtime while maintaining consistent cutting performance. Improved process stability with internal coolant and positive clamping Integrated internal coolant directs cutting fluid close to the cutting edge, supporting efficient coolant delivery, reduced built-up edge and improved chip breaking. The design includes a Torx T8 drive and M3x7 screw for secure clamping of the insert, ensuring repeatable seating and safe operation under higher cutting pressures. These features together reduce thermal stress on the insert and help maintain cutting geometry, so the machining process remains stable across batch runs. Flexible workshop integration and straightforward replacement strategy Compatibility with Korloy LNMX 0603 indexable inserts simplifies procurement and stocking: the same insert family can be used across comparable cutters, lowering inventory complexity. The shank cutter’s modest overall length and a 30 mm cutting length enable integration in confined tool changers and versatile setups. For workshops seeking predictable tool changes, the indexable system reduces regrinding effort and supports quick replacement procedures, contributing to measurable uptime improvements on the shopfloor. For procurement or technical advice on Teknik Makina tools such as the S284-1TM, contact Metav Werkzeuge for personalised consultation and reliable delivery from our Emmerich hub. Technical data SKU: S284-1TM Brand: Teknik Makina Product type: Shank milling cutter Compatible inserts: LNMX 0603 (Korloy) Label: 16mm Schaftfräser LNMX 0603 L110mm mit Innenkühlung Core specifications Diameter: 16 mm Overall length: 110 mm Shank diameter: 16 mm Cutting length (shaft): 30 mm Number of cutting edges: 2 Weight: 0.172 kg Article class: 21180806 Design & special features Internal coolant supply Torx T8 drive, screw M3x7 Indexable system for LNMX 0603 inserts Compact shank geometry for rigid clamping Compatible insert manufacturer: Korloy FAQ What materials can be machined with this shank milling cutter? The shank milling cutter S284-1TM by Teknik Makina is designed for general indexable milling and accepts LNMX 0603 inserts; material suitability depends on the chosen Korloy insert grade and cutting data. How is coolant supplied to the cutting edge? Coolant is supplied via internal channels; the S284-1TM’s internal coolant directs fluid to the insert seat to aid chip evacuation and temperature control. Which insert and screw are required for this cutter? This tool uses LNMX 0603 indexable inserts and secures them with a Torx T8 screw (M3x7); the SKU is S284-1TM for reference when ordering spare parts. Is this cutter suitable for high-speed machining? Process suitability for high-speed milling depends on the insert grade and machine capability; the S284-1TM provides a rigid platform and internal coolant that support higher cutting parameters when paired with appropriate Korloy inserts. What advantages does the 16 mm shank offer in production? A 16 mm shank improves clamping rigidity and reduces deflection compared with smaller shanks, helping to maintain surface finish and extend insert life during repeated operations. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, a 16 mm shank and compatibility with RPMT 0803 inserts to maintain stable cutting conditions and predictable tool life; order this tool directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter for RPMT 0803 indexable inserts — 16 mm shank, through‑coolant A shank milling cutter for RPMT 0803 indexable inserts designed for secure clamping and controlled chip evacuation in general milling operations where insert changeover and coolant delivery are essential Internal through‑coolant for improved chip evacuation 16 mm shank diameter for rigid clamping Compatible with RPMT 0803 Korloy indexable inserts 200 mm overall length with 40 mm cutting length Stability and rigidity for consistent machining results The solid 16 mm shank and compact geometry provide a stiff tool connection that reduces vibration and run‑out, improving surface finish and tool life under moderate to heavy machining. With two cutting edges and a 40 mm cutting length, this milling tool offers a balance between engagement area and stability, suitable for slotting and shoulder milling where consistent cutting conditions matter. The tool body is optimised for secure clamping in standard collets and holders, delivering repeatable results across batch production. Controlled cooling and chip evacuation to protect inserts Equipped with internal coolant, the cutter supplies fluid directly to the cutting zone, which lowers tool temperature and assists chip removal from the insert pocket. This targeted coolant feed reduces thermal stress on the insert seating and can extend the life of RPMT 0803 indexable inserts while maintaining a more consistent cutting force. For operations using Korloy inserts, the through‑coolant arrangement helps to reduce built‑up edge and improves surface integrity on the workpiece, translating into fewer stoppages for manual cleaning or premature insert changes. Practical interface and simple serviceability for reduced downtime Fast insert changes are supported by standard fixing hardware: the tool uses a T8 Torx key and M3x7 screws for secure insert clamping, allowing quick replacement on the shop floor. The cutter, produced by Teknik Makina, is supplied as SKU R310-2TM, which simplifies reordering and inventory management. The compact overall length of 200 mm keeps the tool overhang conservative while the design allows straightforward access to the insert pocket for maintenance tasks, reducing non‑productive time between operations. Contact Metav Werkzeuge today to discuss application suitability for the Teknik Makina shank milling cutter with internal coolant and to arrange a specification check tailored to the production task Technical data Article number: R310-2TM Manufacturer: Teknik Makina Compatible insert: RPMT 0803 (Korloy) Dimensions & performance Diameter: 16 mm Overall length: 200 mm Cutting length: 40 mm Shank diameter: 16 mm Number of cutting edges: 2 Features & compatibility Internal through‑coolant Torx screw: M3x7 Torx key: T8 Product type: shank milling cutter Suitable for RPMT 0803 indexable inserts FAQ What applications is this cutter best suited for? This shank milling cutter is intended for general slotting and shoulder milling where a compact tool with internal coolant and compatibility with RPMT 0803 indexable inserts is required. Which inserts fit this cutter? The cutter accepts RPMT 0803 indexable inserts; use Korloy‑specified RPMT 0803 grades for best seat fit and performance with this tool. How is coolant supplied to the cutting zone? Coolant is delivered through the tool body via the internal coolant channel, directly reaching the insert interface to improve chip evacuation and thermal control. What hardware is required to replace an insert? Insert retention uses an M3x7 Torx screw tightened with a T8 Torx key, enabling quick and standardised insert changes on the shop floor. Can this cutter be identified for reordering? Yes — the tool is listed as SKU R310-2TM, which should be used when reordering or requesting technical data. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise chip control, fast insert changes and secure clamping thanks to the compact 16 mm shank and internal coolant; these features combine to improve cycle stability and reduce downtime. Order the shank milling cutter directly via Metav Werkzeuge or consult our specialists for application-specific advice. Shank milling cutter S398TM — 16 mm shank, internal coolant (Teknik Makina) The shank milling cutter S398TM is a compact milling-body designed for indexable milling with VDKT 11T2 inserts, ideal for CNC side and face milling where quick insert changes and reliable coolant supply are required 16 mm shank diameter for secure clamping Internal coolant for improved chip evacuation Compatible with Korloy VDKT 11T2 inserts 90 mm overall length with 25 mm cutting length Precision and tool-life through internal coolant and compact design The S398TM body pairs a 16 mm shank with a focused internal coolant channel to keep the cutting zone clear and the insert edge cooler under load. This controlled coolant delivery reduces built-up edge and supports consistent cutting conditions, which in turn extends insert life and minimises rejects. The compact 90 mm overall length and 25 mm effective cutting length deliver rigidity at the toolholder, improving dimensional stability in interrupted and continuous milling operations. Fast serviceability and standardised fixing for minimal downtime Changeovers are straightforward: the cutter accepts VDKT 11T2 indexable inserts from Korloy and secures them with the supplied M2.5x5.5 Torx screws tightened using a T8 key. The two cutting edges are indexed quickly, allowing rapid restoration of cutting performance without complex calibration. Standardised fixing hardware and the short cutting length make the tool well suited for production environments where repeatability and fast intervention are priorities. Practical application and economical operation in the workshop Designed as a versatile milling body, the tool is suitable for general-purpose milling tasks on modern CNC equipment where indexable insert systems are preferred for cost efficiency. The combination of reliable clamping from the 16 mm shank, the internal coolant advantage and the lightweight body (approx. 0.135 kg) supports higher machine throughput with lower per-cutting-hour costs. For application queries or specification matches, Metav Werkzeuge provides technical guidance and can advise on optimal insert grades and cutting parameters by phone or e‑mail. Contact Metav Werkzeuge for tailored application advice and to secure the S398TM shank milling cutter with internal coolant from our Emmerich stock Technical Data SKU: S398TM Product type: Shank milling cutter for VDKT 11T2 Manufacturer: Teknik Makina Weight: 0.135 kg Core data Shank diameter: 16 mm Overall length: 90 mm Cutting length (shank): 25 mm Number of cutting edges: 2 Special features Internal coolant Compatible with Korloy VDKT 11T2 indexable inserts Torx key: T8 Torx screw: M2.5x5.5 FAQ Are Korloy VDKT 11T2 inserts compatible with this cutter? Yes. The S398TM is designed specifically to accept VDKT 11T2 indexable inserts and is compatible with Korloy insert variants. Does the cutter provide internal coolant to the insert seat? Yes. The internal coolant channel delivers coolant directly to the cutting zone to aid chip evacuation and reduce thermal wear on the insert. What shank size is required for mounting? The tool has a 16 mm shank, suitable for holders and collets rated for a 16 mm diameter. How are the inserts fixed and which tools are required? Inserts are secured using M2.5x5.5 Torx screws and a T8 key for tightening, enabling quick and standardised insert changes. Which applications suit this milling body best? This milling body is suited to indexable milling operations on CNC machines where short overhang and reliable coolant supply are required; the two cutting edges and 25 mm cutting length help maintain rigidity and repeatable performance. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust clamping solution that combines precise 2 mm cutting width, compatibility with Horn indexable inserts and a secure clamping geometry for repeatable parting and grooving operations; order directly via Metav Werkzeuge or ask the consultants for application support. Teknik Makina Parting and Grooving Clamping Holder D700TM — 16 mm profile, 2 mm cut width The Parting and Grooving Clamping Holder D700TM from Teknik Makina is a right-hand clamping tool designed for parting-off and grooving tasks in precision turning, compatible with Horn indexable inserts Right-hand cutting direction Compatible with Horn indexable inserts 2 mm cutting width for fine grooves 125 mm overall length for controlled reach Secure clamping for consistent parting and grooving results The holder offers a stable clamping interface that keeps insert seating firm under load, reducing vibration and rework. A 16 mm holder profile and the ISO designation 1616 ensure familiar mounting geometry for many turret and quick-change systems; the compact form helps maintain rigidity even with a moderate overhang. With a specified 2 mm cutting width, the tool is intended for narrow parting and precision groove preparation, where repeatable kerf width and predictable chip formation are required. The right-hand cut orientation is clearly defined, allowing setup planners to place the tool correctly in multi-station turrets without ambiguity. Compact geometry that improves process stability and tool life At an overall length of 125 mm and a weight of 0.258 kg, the toolholder is balanced for short to medium overhangs, which supports higher stability and better surface finishes. The combination of 16 mm head width and a maximum grooving depth of 18 mm provides a trade-off between access and stiffness, enabling controlled cutting forces during parting operations. Reduced deflection and more secure insert clamping translate directly into longer insert life and fewer machine interventions, improving uptime in production turning cells. Designed for compatibility and straightforward integration The clamping holder is specified to accept Horn-manufactured indexable inserts, simplifying procurement and ensuring insert availability on-site. Its matching bar designation 2C‑R S224 facilitates checking holder-to-bar fit during tool setup. The clear ISO reference and standardised profile reduce the need for customised tool-adapters and permit fast changeovers. For teams planning process documentation, the nominal dimensions and the right-hand cutting assignment make cycle planning and NC-program annotation more precise. Practical benefits for workshop and production environments Using a standardised, compact parting holder reduces setup time and supports consistent quality across batches. The holder’s modest mass and clear geometric references assist in optimising turret balance and avoiding unnecessary counterweights. Where fine grooves and narrow parting cuts are frequent, the specified 2 mm kerf and the secure clamp design help achieve repeatable part geometry, which reduces scrap and downstream machining corrections. The tool is therefore suited to precision workshops and jobbing operations that prioritise reliable, low-variation turning outcomes. For application advice, process integration or to secure stock from Metav Werkzeuge, contact our consultants at Metav Werkzeuge — phone +49 2822 7131930 or email info@metav-werkzeuge.com; order the Teknik Makina D700TM for reliable, compact parting solutions. Technical data Article number: D700TM Manufacturer: Teknik Makina Weight: 0.258 kg Overall length: 125 mm Holder profile / height: 16 mm Head width: 16 mm Cutting width: 2 mm Maximum grooving depth: 18 mm Cutting direction: right Compatible with Horn indexable inserts ISO designation: 1616 Bar designation: 2C-R S224 Application: parting and grooving Storytrigger: stechklemmhalter FAQ What materials is the holder suitable for? The Parting and Grooving Clamping Holder D700TM is a mechanical holder; suitability depends on the chosen Horn inserts and cutting data rather than the holder itself Is the cutting direction fixed or reversible? The holder is designed for a right-hand cutting direction and should be mounted accordingly for correct parting and grooving orientation Which inserts fit this clamping holder? This holder is specified for Horn indexable inserts; consult Horn insert catalogues for matching grades and geometries to the required material and finish Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com