Gibt es einen Hahn und Kolb Online Shop?

Taking advantage of a compact 170 mm overall length and a robust 32 × 32 mm shank, this clamp holder delivers stable clamping and reproducible results in precision turning applications; its M16 clamping thread and M5×26 screw ensure secure fixation. Order or request availability from Metav Werkzeuge for reliable supply and workshop support. Clamp holder L170 mm (D105-3TM) by Teknik Makina — compact 170 mm toolholder, 32×32 mm shank The Clamp holder L170 mm is a compact clamping toolholder designed for precise metalcutting and general turning applications where a stable, repeatable tool position and straightforward fastening are required. Compact 170 mm overall length 32 × 32 mm shank cross-section M16 thread for secure clamping 72.5° cutting angle for controlled engagement Stable clamping for consistent machining quality The holder’s 32 × 32 mm shank and well-defined geometry provide a stable interface with compatible tool posts and toolblocks, reducing chatter and improving surface finish. The M16 clamping thread combined with the M5×26 clamping screw offers a rigid connection between tool and holder, which translates directly into repeatable component tolerances and lower scrap rates. Dimensioned mass of 1.338 kg contributes to vibration damping while remaining compact enough for dense turret configurations. Quick setup and reliable fixation Designed for efficient workshop workflow, the toolholder uses a standard M5×26 clamping screw and an Allen key size of 3 mm for assembly and adjustment. The ISO 3232 designation reflects the holder’s cross-section and compatibility with common clamping systems. The straightforward fastening concept reduces setup time and facilitates predictable tool offsets, improving overall machine uptime and allowing quicker changeovers between turning operations. Geometry engineered for predictable cutting behaviour With a 72.5° cutting angle and a cutting height of 50 mm, the holder provides defined clearance and chip flow characteristics that support stable engagement during roughing and finishing passes. The limited cutting‑head width of 16 mm suits compact insert geometries and enables close tool spacing on multi‑station turrets. Explaining the geometry: a larger cutting angle increases clearance and lowers radial cutting forces, which benefits tool life and workpiece quality in many turning scenarios. Compact dimensions for flexible machine integration An overall length of 170 mm and a 32 × 32 mm cross-section make this holder suitable for workshops requiring space-efficient tooling without compromising stability. The compact design supports flexible fixturing on both manual lathes and CNC turning centres where a combination of stiffness and accessibility is needed. The holder’s measured characteristics allow planners to predict envelope requirements and plan tool layouts with confidence. For dependable clamping performance and inventory from Teknik Makina, contact Metav Werkzeuge to discuss availability and application fitment from our Emmerich warehouse. Technical data SKU: D105-3TM Label: Clamp holder L170 mm Manufacturer: Teknik Makina Core specifications Overall length: 170 mm Weight: 1.338 kg Shank width: 32 mm Shank height: 32 mm Cutting head width: 16 mm Cutting height: 50 mm Cutting angle: 72.5° Design / Special features M16 clamping thread Clamping screw M5×26 ISO designation: 3232 Allen key: 3 mm FAQ What is the overall length and model designation of this holder? The clamp holder is 170 mm long and is sold under SKU D105-3TM, designated as Clamp holder L170 mm. Which shank dimensions does the holder use? The holder features a 32 × 32 mm shank cross-section (ISO 3232), suitable for tool posts and fixtures that accept this standard size. How is the tool fixed in place and which screw is supplied? Fixation is achieved via an M16 clamping thread and an M5×26 clamping screw; an Allen key size of 3 mm is required for tightening. What cutting geometry should be expected from the holder? The holder presents a 72.5° cutting angle with a cutting height of 50 mm and a cutting-head width of 16 mm, providing stable engagement and predictable chip flow. Is this holder suitable for dense turret configurations? Yes, the compact 170 mm overall length and 32 × 32 mm profile are intended for installations where space efficiency and stiffness are both required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise compatibility, rigid clamping and clear ISO profiling to keep tool changeovers quick and machining stable; the holder's CKJNR 3232 geometry and compatibility with KNUX 1604 inserts support efficient right-hand turning in production environments. Order this clamping holder via Metav Werkzeuge or contact their consultants for application advice. Clamping holder CKJN for KNUX Indexable Inserts — right-hand, ISO CKJNR 3232 A clamping holder engineered for right-hand turning with KNUX-compatible indexable inserts, intended for robust workshop and light-industrial turning applications. Right-hand turning orientation Compatible with KNUX 1604 inserts ISO profile CKJNR 3232 170 mm overall length, weight 1.31 kg Stable clamping for repeatable machining results The holder provides a rigid clamping solution that reduces vibration and improves surface finish during turning. With an overall length of 170 mm and a mass of 1.31 kg, the design balances stiffness with manageable tool overhang. The CKJNR 3232 profile ensures a standardised fit in tool posts and quick replacement cycles, which contributes to shorter set-up times and higher machine utilisation. Use in right-hand operations benefits from the optimised approach angle to maintain consistent chip flow and reduce edge loading. Proven compatibility that simplifies tooling logistics Designed specifically to accept KNUX 1604 indexable inserts, the toolholder removes uncertainty from insert selection and inventory management. The 93° cutting angle and a cutting height of 35 mm align the insert cutting edge with typical lathe centres, reducing the need for adapter shims. By standardising on a familiar insert size, procurement and toolroom teams can streamline stock and cut planning complexity, yielding faster job turnarounds and predictable performance across batches. Clear geometry and dimensions for confident setup Crucial dimensions such as holder height 32 mm, head width 40 mm and holder width 32 mm are specified to support correct mounting and clearance checks at the planning stage. The ISO designation and the named shank reference P16 allow straightforward cross-referencing with tool posts and toolblocks. These measurables enable engineering teams to verify compatibility before machining, lowering the risk of crashes or costly rework and improving process reliability. Built for workshop use with attention to handling The machining centre benefit is not only in metal removal but in serviceability: the clamping mechanism and robust body construction permit repeatable insert seating and secure tightening without complex adjustment. The combination of standard ISO form and a compact footprint helps to integrate the holder into existing turning programmes with minimal adaptation. For production floors that prioritise uptime, the durable construction and proven insert interface support continuous operation with predictable maintenance intervals. For technical guidance on Teknik Makina clamping holders and to confirm compatibility for specific turning tasks, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: RD013TM Manufacturer: Teknik Makina Product name: CKJN for KNUX Indexable Inserts ISO designation: CKJNR 3232 SKU: RD013TM Facts Overall length: 170 mm Weight: 1.311 kg Cutting height: 35 mm Holder height: 32 mm Head width: 40 mm Holder width: 32 mm Cutting angle: 93° Special features Compatible inserts: KNUX 1604 Cutting direction: right-hand Shank reference: P16 Robust clamping geometry for indexable inserts Manufacturer: Teknik Makina FAQ What inserts fit this holder? The holder accepts KNUX 1604 indexable inserts; Teknik Makina's CKJN geometry aligns the insert seat with the CKJNR 3232 ISO profile for secure clamping. Is the holder suitable for right-hand turning only? Yes, the CKJN clamping holder from Teknik Makina is specified for right-hand turning operations and features a cutting direction optimised for that use. What are the key dimensions to check before installation? Verify the overall length (170 mm), holder height (32 mm), head width (40 mm) and cutting height (35 mm) to ensure compatibility with the intended tool post and workpiece set-up. Does the holder comply with an ISO profile? The toolholder follows the CKJNR 3232 ISO designation, enabling straightforward interchangeability with corresponding tool posts and fixtures. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, right-hand turning solution that combines compatibility with VBMT 1604 inserts, a 32 mm tool height and secure clamping for consistent results on production lathes; order the holder directly via Metav Werkzeuge or consult Metav's specialists for project alignment. Klemmhalter (SVJB for VBMT Indexable Inserts) by Teknik Makina — Right-hand, 32 mm height The Klemmhalter (SVJB for VBMT Indexable Inserts) is a right-hand turning holder designed for VBMT 1604 indexable inserts, intended for general turning applications where reproducible tool set-up and consistent cutting geometry are required. Right-hand turning holder, cutting angle 93° Compatible with VBMT 1604 indexable inserts 32 mm tool height, 40 mm cutting-head width Robust construction; overall length 170 mm Consistent geometry for reliable turning performance The holder delivers a stable cutting arrangement through its defined cutting angle 93° and ISO designation SVJBR 3232, which together ensure repeatable tool orientation on the turret. Compatibility with VBMT 1604 indexable inserts removes ambiguity at tool change and reduces set-up time: the insert pocket and clamping arrangement are engineered to position the insert accurately and maintain the intended rake and clearance during cutting. For production environments this translates into fewer adjustments, improved cycle-time predictability and more consistent part tolerances. Secure clamping and workshop-friendly dimensions Built with secure clamping features and a compact footprint, the toolholder’s 32 mm height and 40 mm cutting-head width balance rigidity with access to confined workpieces. The holder’s overall length 170 mm and mass of 1.37 kg provide the necessary overhang without excessive vibration for common turning tasks. The clamping concept is straightforward to operate and compatible with P16-profile tool bars, enabling fast replacement in modular turret systems and minimising downtime during insert changes. Practical integration and user benefits on the lathe The right-hand orientation and clear designation for indexable inserts make the holder practical for standard turning programmes, including facing and light profile turning where VBMT inserts are commonly used. The compact design simplifies storage and tool management across a workshop fleet, while the standardised ISO form facilitates interchange with existing toolholders. Where process reliability matters, this holder supports consistent chip control and repeatable insert seating, helping to reduce scrap rates and maintain throughput. Contact Metav Werkzeuge to discuss how the Teknik Cutting Tools SVJB holder can be integrated into current tool sets; email info@metav-werkzeuge.com or call +49 2822 7131930 for detailed advice or a tailored quotation. Technical data Article number: D238-1TM Manufacturer: Teknik Makina Product name: Klemmhalter Secondary designation: SVJB for VBMT Indexable Inserts ISO designation: SVJBR 3232 Compatible inserts: VBMT 1604 Cutting direction: right Core dimensions Tool height: 32 mm Tool width: 32 mm Cutting-head width: 40 mm Cutting height: 40 mm Overall length: 170 mm Cutting angle: 93° Weight: 1.37 kg Features & compatibility Right-hand cutting direction Compatible with VBMT 1604 indexable inserts Bore designation: P16 ISO form: SVJBR 3232 Suitable for standard turret and bar systems FAQ Which insert type fits this holder? The holder is designed for VBMT 1604 indexable inserts; the insert pocket and clamping geometry match that insert format for reliable seating. Is the cutting direction specified? Yes — the toolholder is configured for right-hand cutting, suitable for standard right-hand turning operations. What are the key dimensions to check before fitting? Key dimensions are tool height 32 mm, cutting-head width 40 mm and overall length 170 mm; these help verify clearance and turret compatibility. What is the ISO designation and why is it relevant? The ISO designation SVJBR 3232 identifies the holder form and mounting interface, which simplifies matching to tool posts and ensures predictable insert orientation. Which tool-bar bore or clamp designation is required? The holder uses bore designation P16, so ensure the turret or bar accepts P16-style clamping. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 32 mm shank width, a 170 mm overall length and direct compatibility with VER27 indexable inserts to ensure stable clamping and consistent turning results; order the clamping holder directly via Metav Werkzeuge or consult our specialists for application advice. Clamping holder VER27 L170mm — for VER27 indexable inserts, 32 mm shank width (Teknik Makina) A Clamping holder VER27 L170mm designed to secure VER27 indexable inserts for turning applications, offering a compact footprint with a robust clamping interface suitable for routine workshop use Clamping holder for VER27 indexable inserts 32 mm shank width for standard toolholders 170 mm overall length for stable mounting Torx T15 screw drive M4x11 included Built for secure, repeatable clamping The holder’s geometry delivers a dependable interface between tool and machine: a 32 mm shank width paired with a 170 mm overall length gives a favourable balance between rigidity and accessibility at the toolpost. Compatibility with VER27 indexable inserts ensures standardised insert seating and repeatable positioning, which reduces set-up variance and improves component consistency during series production. The ISO designation 3232 documents the holder’s envelope and helps verify fitment in existing tool systems. Straightforward installation and faster tool changes Fast, reliable fastening is achieved via the M4x11 screw driven with a Torx T15 key, which simplifies insert changes and minimises downtime during maintenance operations. At roughly 1.215 kg, the holder remains manageable for routine handling while providing mass for vibration damping, contributing to improved surface finish and tool life. The integrated cutting-head width of 36 mm accommodates the insert pocket reliably, and the standardised screw interface reduces the need for bespoke tooling during assembly. Workshop-ready durability and clear ordering Manufactured for industrial use, the design focuses on repeatable performance under shop-floor conditions. The compact profile and standardised interfaces permit straightforward integration into existing turning workflows, while clear identifiers such as SKU D523TM and label information expedite procurement and inventory management. Metav Werkzeuge’s distribution ensures dependable supply and a quality-check filter from Emmerich, supporting continuity of production and giving purchasing managers confidence in delivery and product consistency. Contact Metav Werkzeuge for a tailored quotation or technical clarification on the Teknik Cutting Tools clamping holder VER27 L170mm (SKU D523TM) — email info@metav-werkzeuge.com or call +49 2822 7131930 for swift assistance Technical data Article number: D523TM Product type: Clamping holder Designation: Klemmhalter VER27 L170mm EClass: 21181004 Dimensions & weight Overall length: 170 mm Shank width: 32 mm Shank height: 32 mm Cutting head width: 36 mm Weight: 1.215 kg Mounting & fastening Compatible inserts: VER27 ISO designation: 3232 Torx key: T15 Torx screw: M4x11 Manufacturer: Teknik Makina SKU: D523TM FAQ Which inserts fit this holder? The clamping interface is specified for VER27 indexable inserts; the seating and pocket geometry conform to the VER27 standard, ensuring correct insert location and reliable cutting performance. How is the holder secured and changed on the toolpost? Securing is via an M4x11 screw operated with a Torx T15 driver; the straightforward screw interface supports quick tool changes and reduces auxiliary tooling requirements for maintenance. Is this holder suitable for routine workshop turning tasks? Yes—the Clamping holder VER27 L170mm from Teknik Makina (SKU D523TM) is engineered for repeated tool changes and stable clamping, making it appropriate for standard workshop and small-series production environments. What dimensions should be checked before mounting? Verify the 170 mm overall length, 32 mm shank width and 36 mm cutting-head width against the machine’s toolpost clearance and the turret envelope to ensure trouble-free installation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, secure turning with a robust clamping design and standard ISO shank compatibility; the result is consistent tool performance and reduced setup time. Combine reliable left-hand cutting geometry and compatibility with WN-- 0804 indexable inserts for efficient production. Order the clamping holder directly via Metav Werkzeuge or ask our consultants if needed. Clamping holder MWLNL 3232 — left-hand, for WN-- 0804 inserts (Teknik Makina) Clamping holder for turning operations, designed for use with WN-- 0804 indexable inserts and a standard MWLNL 3232 shank; suitable for stable, left-hand cutting applications in workshop and light industrial turning. Robust clamping system for stable turning Compatible with WN-- 0804 indexable inserts ISO MWLNL 3232 shank for standard toolholders Left-hand cutting with 95° cutting angle Secure clamping that keeps cycles running The clamping holder is engineered to provide a dependable mechanical grip on the insert, reducing micro-movement during cuts and lowering rework rates. With a cutting height of 35 mm and a holder height of 32 mm, the geometry maintains a consistent tool edge position so setups remain repeatable. This stability translates into fewer interruptions on the shop floor and improved process reliability over long runs. Designed for proven insert compatibility and predictable results Using the MWLN design for WN-- 0804 indexable inserts, the holder supports widely available insert formats, simplifying inventory and replacement. The ISO designation MWLNL 3232 indicates a standardised shank form that fits common tool posts, allowing quick installation. Because the unit is specified for left-hand cutting at a 95° cutting angle, planners can assign it to suitable turning operations without uncertainty about orientation or edge engagement. Compact dimensions with practical handling and performance Measuring 170 mm overall length with a cutting-head width of 40 mm and weighing 1.349 kg, the unit balances rigidity and manoeuvrability. These proportions make it straightforward to position on most lathes while offering the mass necessary to dampen vibration in moderate cutting conditions. The clear, standardised mechanical specification reduces setup time and assists toolroom personnel in selecting the correct holder for the application. For secure left-hand turning with Teknik Cutting Tools' clamping holder, contact Metav Werkzeuge for ordering or technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: D326TM Product: Clamping holder (MWLN for WN-- indexable inserts) Brand: Teknik Makina Model designation: MWLNL 3232 For inserts: WN-- 0804 Dimensions & core values Overall length: 170 mm Holder height: 32 mm Holder width: 32 mm Cutting-head width: 40 mm Cutting height: 35 mm Weight: 1.349 kg Cutting angle: 95° Compatibility & special features Cutting direction: left-hand Shank designation: MWLNL 3232 Turning application: for WN-- 0804 indexable inserts Bar/stem designation: P08 Suitable for standard tool posts and holders FAQ What inserts fit this clamping holder? The clamping holder is compatible with WN-- 0804 indexable inserts, enabling use of common square 0804 inserts for turning tasks. Is the holder suitable for right-hand turning? This holder is specified for left-hand cutting with a 95° cutting angle; for mirrored operations, a right-hand variant should be selected. What are the main dimensions to check before mounting? Key dimensions are 170 mm overall length, 32 mm holder height, 40 mm cutting-head width and 35 mm cutting height; confirm these against the machine tool envelope. Does the MWLNL 3232 designation fit standard toolposts? Yes, the MWLNL 3232 ISO shank designation corresponds to a common shank form intended for standard toolholder mounts. Who supplies this tool and where can technical advice be obtained? The product is supplied by Teknik Makina; for ordering or technical clarification Metav Werkzeuge is available and can advise on integration into existing tool setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from reliable right-hand grooving with precise clamping, 170 mm overall length and compatibility with MGM 800 indexable inserts; the D687-3TM improves process stability and reduces set-up time. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Stechklemmhalter MGM 800 L170mm — Grooving clamping holder for MGM 800 indexable inserts, right-hand, 170 mm Stechklemmhalter MGM 800 L170mm is a purpose-built grooving clamping holder designed for heavy-duty workshop and light production use, engineered to accept MGM 800 indexable inserts for consistent right-hand grooving applications. Compatible with MGM 800 indexable inserts 170 mm overall length for deeper reach Right-hand grooving with 30 mm max depth Robust 32 mm clamping head, 8 mm cutting width Precision and process reliability for groove turning The grooving clamp is engineered to deliver consistent results in repeat production. The combination of a 32 mm clamping head and a secure ISO 3232 clamping interface ensures stable insert seating and low vibration, which in turn preserves tool life and surface finish. With a clear numerical specification for max. 30 mm grooving depth, the holder supports defined machining windows so cycle times can be planned precisely and quality targets met routinely. Compatibility and setup efficiency in mixed-tool environments Designed for use with MGM 800 indexable inserts and compatible with Korloy supply ranges, this holder simplifies tool inventory by aligning with common insert platforms. The straightforward clamping mechanism, secured by an M8x22 screw and adjusted with a 6 Allen key, reduces set-up time and allows fast insert changes during shift work. Clear mechanical interfaces translate into less downtime and more predictable throughput for batch or single-part manufacturing. Robust design for workshop and light production conditions At a weight of 1.275 kg and an overall length of 170 mm, the holder balances rigidity and accessibility, enabling deeper reach without excessive tool overhang. The 8 mm cutting width is suitable for a wide range of grooving tasks where stable chip control and defined kerf width are essential. The designation ISO 3232 denotes an industry-standard clamping geometry, which supports interchangeability and simplifies tool management across machines. Practical benefits and recommended use cases This grooving clamping holder is particularly suitable for turning centres performing through-grooving and finish-grooving on steel and alloy components where a right-hand cut is required. Its compatibility with Korloy and MGM 800 inserts makes it a pragmatic choice for workshops seeking a balance between tool availability and machining performance. The solid mechanical interface reduces the likelihood of micro-movements, helping to maintain tolerances during serial production. Request tailored application advice from Metav Werkzeuge for Teknik Makina grooving clamping holders or arrange supply from our Emmerich warehouse for fast, reliable delivery Technical data Article number: D687-3TM Label: Stechklemmhalter MGM 800 L170mm Manufacturer: Teknik Makina Product type: Grooving clamping holder ECLASS: 21181005 Facts Overall length: 170 mm Weight: 1.275 kg Clamping width: 32 mm Clamping height: 32 mm Cutting-head width: 32 mm Max grooving depth: 30 mm Cutting width: 8 mm Screw: M8x22 Hex key: 6 Allen Cutting direction: right Special features Compatible with MGM 800 indexable inserts ISO clamping designation: 3232 Suitable for Korloy inserts SKU: D687-3TM FAQ What inserts are compatible with this grooving clamping holder? The holder accepts MGM 800 indexable inserts and is listed as compatible with Korloy insert ranges for straightforward sourcing and installation. What is the maximum grooving depth achievable with this tool? The grooving capability is specified at a maximum depth of 30 mm, allowing for deeper groove operations within stable cutting parameters. How is the insert secured and what tools are required for maintenance? The insert is clamped via an ISO 3232 interface using an M8x22 clamping screw; a 6 Allen key is required for tightening and insert changes. Is the holder suited for serial production environments? Yes; the holder’s robust 32 mm clamping head and stable design make it suitable for repeated production cycles where process reliability and dimensional consistency are priorities. Which cutting direction does the holder support? This grooving clamping holder is configured for right-hand cutting direction, optimised for right-hand grooving operations. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a secure 32 mm clamping height and a 45° cutting angle for improved chip control and consistent surface finish; the right-hand orientation and 170 mm overall length ensure stable setup in standard turning operations. Order the tool directly via Metav Werkzeuge or consult our specialists for compatibility advice. DSSNR 3232 — Tool holder for SNMG indexable inserts, right-hand 45° (Teknik Makina) A robust DSSNR 3232 tool holder engineered for turning with SNMG 1204 indexable inserts; designed for right-hand cutting and optimised chip flow at a 45° approach angle. Designed for SNMG 1204 indexable inserts 45° cutting angle for controlled chip evacuation Right-hand orientation for standard turning 32 mm clamping height with 170 mm overall length Stable clamping for accurate turning and longer tool life The holder is constructed to provide rigid support for indexable inserts, with a 32 mm clamping height and a 40 mm body width that minimise vibration during cutting. This rigidity leads to a more consistent cutting edge engagement, which is translated into improved surface finish and extended insert life. Where operators require repeatable results across batch runs, the secure clamp reduces setup variance and helps maintain dimensional tolerances without frequent readjustment. Compatibility and workshop efficiency with standard interfaces Designed around the common SNMG 1204 format, the holder uses the ISO designation DSSNR 3232 and a compatible shank marking P12, enabling straightforward integration into existing turret systems. The 170 mm overall length and 32 mm head width balance reach and rigidity, supporting typical turning tasks while keeping tool overhang manageable. Reduced changeover times are achieved because inserts and clamping screws follow standard sizes, allowing faster insert replacement and less downtime between operations. Optimised cutting geometry for effective chip control The fixed 45° cutting angle combined with right-hand orientation focuses chip flow away from the workpiece and the clamping zone, which simplifies chip handling and reduces the risk of recutting. For process planners pursuing higher material removal rates, the geometric setup supports stable cutting conditions and predictable thermal behaviour at the cutting edge. The holder’s measured mass (1.28 kg) contributes to dampening of high-frequency vibrations, which is beneficial when switching between roughing and finishing passes. Reliable construction for production environments Manufactured to industrial standards, the holder is engineered for durability and consistent performance in workshop environments. The moderate weight and compact head dimensions make it suitable for a wide range of lathes and turning centres where repeatability and minimal maintenance are priorities. Spare-part familiarity—standardised screws and interfaces—means servicing can be handled with normal workshop tools, helping to maintain uptime and predictable production flows. Contact Metav Werkzeuge today for detailed technical information and to discuss how the DSSNR 3232 tool holder from Teknik Makina can be integrated into existing turning setups Technical data Article number: D205TM Manufacturer: Teknik Makina Core numeric data Clamping height: 32 mm Cutting head width: 32 mm Body width: 40 mm Cutting height: 36 mm Overall length: 170 mm Weight: 1.28 kg Cutting angle: 45° Special features ISO designation DSSNR 3232 Compatible with SNMG 1204 indexable inserts Right-hand cutting direction Shank designation P12 Brand: Teknik Makina FAQ Which inserts fit this holder? The holder is specified for SNMG 1204 indexable inserts; compatibility is ensured by the DSSNR 3232 ISO form factor. Is the holder suitable for left-hand turning? This model is configured for right-hand cutting; left-hand operations require a left-oriented variant. What is the overall length and its workshop benefit? An overall length of 170 mm provides a balance between reach and rigidity, reducing overhang-related vibration. How does the 45° angle affect chip control? The 45° cutting angle directs chips away from the clamping zone, improving chip evacuation and surface finish. Which shank designation is used for mounting? The tool holder carries the shank marking P12, matching standard turret and toolpost interfaces. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust extension that combines a secure M16 thread, a substantial 170 mm overall length and a 32 mm shaft for stable, extended machining operations — order the VT520TM extension directly via Metav Werkzeuge or consult our technical team for compatibility advice. Extension for screw-in cutters VT520TM — Teknik Cutting Tools, M16 thread, 170 mm overall length A VT520TM extension for screw-in cutters engineered to extend cutter reach while preserving rigidity for milling and finishing tasks in industrial and workshop environments. M16 thread for secure mounting 170 mm overall length for extended reach 32 mm shaft diameter for high stiffness Robust 1.26 kg construction for stability Greater reach without compromising rigidity Extending the toolholder length enables access to deeper or recessed workpieces; the VT520TM achieves this with a 170 mm overall length that increases reach while an oversized 32 mm shaft diameter maintains lateral stability. The combination of reach and stiffness reduces deflection during heavy cuts, which in turn improves dimensional consistency and prolongs cutter life. For workshops where space is limited or parts feature deep bores, this extension keeps the cutting geometry predictable and repeatable. Secure connection and reliable compatibility A precise M16 thread and a dedicated opening diameter of 28.7 mm for thread-in cutters ensure a firm mechanical union between extension and cutter. The 40 mm taper/cone length stabilises the seating geometry, reducing micro-movements that can generate chatter. This mechanical certainty supports higher feed rates and consistent surface finish, translating raw specifications into measurable productivity gains on the shop floor. Practical handling and workshop benefits Weighing 1.26 kg, the extension balances inertial mass for steady cutting without becoming unwieldy during tool changes. The solid construction supports robust clamping and repeatable repositioning, which speeds set-up and reduces rework. When combined with standard thread-in cutters, the extension brings productive versatility to milling cells and toolrooms, making it suitable for both prototyping runs and serial production where controlled extension is required. Contact Metav Werkzeuge for a detailed fitment consultation for the Teknik Cutting Tools VT520TM extension and to arrange procurement; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VT520TM Manufacturer: Teknik Cutting Tools ECLASS: 21189208 ETIM: EC002219 Dimensions & weight Shaft diameter: 32 mm Cutter opening diameter: 28.7 mm Taper/cone length: 40 mm Overall length: 170 mm Thread: M16 Weight: 1.26 kg Design & features Extension for screw-in cutters (einschraubfräser) Secure M16 threaded connection Tapered seating for reduced runout Designed for industrial milling and finishing FAQ What is the primary purpose of this extension? The VT520TM extension is designed to increase cutter reach while maintaining rigidity; it enables deeper machining with a secure M16 connection. Which cutter shank sizes does the extension accept? The unit features an opening diameter of 28.7 mm, intended for compatible thread-in cutters and standardised seating geometries. How does the extension affect machining stability? By combining a 32 mm shaft with a 40 mm taper, the extension minimises lateral deflection and helps preserve surface quality during longer reach operations. Who supplies this extension and where can it be ordered? The extension is supplied by Teknik Cutting Tools (SKU VT520TM) and can be procured or discussed via Metav Werkzeuge for fitment advice. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a 32 mm shank and a 40 mm long taper delivers extended reach with stable seating for demanding milling operations; the robust M16 thread and 170 mm overall length support secure mounting and improved tool access. Order the extension directly via Metav Werkzeuge or ask the consultants for application-specific advice. Extension for screw-in cutters VT521TM – 32 mm shank, M16 thread (Teknik Makina) The Extension for screw-in cutters VT521TM gives extended tool reach and rigid clamping for CNC milling and workshop applications in which screw-in cutters require secure, low-vibration mounting 32 mm shank for stable clamping M16 thread for secure attachment 170 mm overall length for extended reach 40 mm long taper for rigid seating Extended reach with uncompromised rigidity The VT521TM extension is engineered to extend cutter reach without sacrificing stability. With a 32 mm shank and a 170 mm overall length, the holder increases accessibility to deep or awkward features while maintaining a compact profile that reduces deflection. The 40 mm long taper provides a larger contact surface inside the cutter body, which helps to reduce runout and vibration during high-feed operations. This combination supports consistent chip formation and predictable surface finish for milling tasks. Precision fit that reduces runout and improves process reliability Accuracy in the connection is critical for repeatable results; the M16 thread mates precisely with screw-in cutters and, together with the 28.7 mm cutter opening, ensures a tight mechanical fit. This dimensional accuracy minimises axial and radial play, lowering the risk of chatter and tool failure. For operations where concentricity affects tolerances, the precise interface reduces scrap rates and downstream rework, contributing to more efficient production cycles. Built for workshop and CNC environments with practical handling Weighted at 1.254 kg, the extension offers a reassuring feel for manual setup while remaining suitable for use in automated tool-changing systems. The robust construction supports everyday shop use, from prototype work to serial production. The straightforward geometry facilitates fast inspection and replacement during maintenance, supporting predictable machine uptime. Supplied dimensions and clear technical data make the component easy to specify in tooling lists and BOMs for process planners. Contact Metav Werkzeuge today to discuss how the Teknik Makina extension VT521TM with M16 thread fits into the tooling concept; email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice Technical data Article number: VT521TM Manufacturer: Teknik Makina Total length: 170 mm Shank diameter: 32 mm Cutter opening: 28.7 mm Long taper (insertion): 40 mm Thread: M16 Weight: 1.254 kg Facts Total length: 170 mm Shank diameter: 32 mm Cutter opening: 28.7 mm Long taper: 40 mm Weight: 1.254 kg Special features Suitable for screw-in cutters Designed for CNC milling and workshop applications Secure M16 threaded connection Long taper for improved seating and reduced runout FAQ Is this extension compatible with common screw-in cutter systems? The extension VT521TM is intended for screw-in cutters and features an M16 threaded interface and a 28.7 mm cutter opening to match compatible cutter bodies. What benefits does the 40 mm long taper bring? A 40 mm long taper increases contact area between the extension and cutter, improving seating stability and reducing runout during milling with the VT521TM. Can the extension be used on CNC machines with automatic tool changers? The VT521TM’s dimensions and weight (1.254 kg) make it suitable for many CNC environments; compatibility depends on the machine’s tool-holder specifications and clamping system. How does the 32 mm shank affect tool performance? The 32 mm shank provides a robust cross-section for clamping, which lowers deflection under load and supports consistent finishing when using screw-in cutters. Is the VT521TM suitable for precision finishing operations? Yes—its precise thread fit and long taper contribute to low vibration and improved concentricity, making the VT521TM appropriate for finishing where dimensional accuracy matters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact holder that combines sturdy construction with predictable repeatability: the design supports MGM 600 indexable inserts, offers a 32 mm clamping head for reduced vibration and a 25 mm maximum cutting depth for deeper grooving tasks. Order supply or request technical advice via Metav Werkzeuge for fast delivery and tailored recommendations. Grooving clamping holder MGM 600 L170mm – right-hand clamping holder with 170 mm overall length (Teknik Makina) The Grooving clamping holder MGM 600 L170mm is a purpose-built clamping solution for MGM 600 indexable inserts, engineered for right-hand grooving and parting operations in production and repair workshops Fits MGM 600 indexable inserts (Korloy) Robust 32 mm clamping head width 170 mm overall length, 25 mm max cutting depth Stable clamping for consistent groove quality The holder delivers a rigid interface between toolpost and insert, with a 32 mm clamping head and a compact L170 mm body that reduces overhang and vibration. The resulting stability improves surface finish and tool life by lowering chatter during parting and grooving, which is critical where dimensional repeatability matters. The toolholder’s mass (approx. 1.272 kg) contributes to damping without sacrificing manoeuvrability, so cycle times remain competitive while tolerances are held. Fast, repeatable set-up that lowers downtime Designed for straightforward assembly, the holder uses an M8x22 clamping screw and a 6 Allen key interface for secure fixation. The ISO 3232 clamping geometry provides repeatable positioning of the insert, simplifying index changes and reducing set-up variance across batches. For operations that demand quick tool changes, this configuration minimises machine downtime and supports predictable process control — a clear efficiency gain for small series and serial production alike. Broad compatibility and workshop fit Compatibility with MGM 600 indexable inserts (Korloy) makes the holder a versatile choice across common insert ranges, while the right-hand cutting orientation and 25 mm maximum cutting depth accommodate deeper grooving tasks without additional tooling. The clamping head width and insert seating are suited to both lathe and turning-centre applications where stable parting is required. The compact footprint and standardised fastening mean the holder integrates easily into established tooling sets and tool magazines. Contact Metav Werkzeuge for a tailored recommendation or to arrange supply of the Teknik Makina grooving clamping holder D687-1TM and additional compatible inserts Technical data SKU: D687-1TM Label: Stechklemmhalter MGM 600 L170mm Product type: Grooving clamping holder Manufacturer: Teknik Makina Facts Overall length: 170 mm Weight: 1.272 kg Clamping head width: 32 mm Clamping head height: 32 mm Cutting head width: 32 mm Insert cutting width: 6 mm Max cutting depth: 25 mm Cutting direction: right Clamping screw: M8x22 Allen key: 6 Allen Compatible inserts: MGM 600 Compatible insert manufacturer: Korloy ISO designation: 3232 ECLASS: 21181005 Special features Suitable for MGM 600 indexable inserts Right-hand grooving and parting orientation Standardised ISO seating for repeatable positioning Compact design for reduced overhang and vibration Robust clamping screw and Allen-key fixation FAQ What insert series fits this clamping holder? The holder is designed for MGM 600 indexable inserts and is compatible with Korloy MGM 600 inserts for reliable seating and repeatable cutting geometry. What is the maximum grooving depth achievable with this holder? The grooving clamping holder supports a maximum cutting depth of 25 mm, suitable for deeper parting and grooving operations where the insert geometry allows. Which direction of cut is this holder intended for? This clamping holder is configured for right-hand cutting, optimised for conventional right-hand grooving and parting setups. What fastening hardware is used for the clamping mechanism? Fixation is achieved with an M8x22 clamping screw, tightened with a 6 Allen key for secure and repeatable clamping. What is the article number or SKU for ordering? The product is listed as D687-1TM, referenced as the Tek­nik Makina grooving clamping holder for MGM 600 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precise combination of compatibility with MGM 800 indexable inserts, a sturdy 25 × 25 mm clamping area and a 170 mm overall length for reliable parting operations; order directly via Metav Werkzeuge or contact our consultants for application advice. Grooving clamp holder MGM 800 L170 mm — left-hand parting holder by Teknik Makina The Grooving clamp holder for MGM 800 indexable inserts is a left-hand parting and grooving solution designed for stable, repeatable cuts in production and workshop environments. Compatible with MGM 800 indexable inserts Left-hand cutting orientation for parting 170 mm overall length for deeper grooves 25 × 25 mm clamping area with 32 mm cutting face Stable compatibility that reduces setup time and scrap The holder is engineered for direct use with MGM 800 indexable inserts and inserts from Korloy, ensuring fast tool changes and repeatable seating. This compatibility simplifies inventory management and reduces downtime compared with bespoke tooling solutions. The left-hand orientation supports conventional parting cycles and is particularly suited to setups where the toolpath requires a left-facing approach. The clear match to common insert standards means fewer seating errors and a more predictable machining result. Robust design for vibration control and consistent clamping A compact clamping area of 25 mm by 25 mm and an ISO designation of 3232 create a stable interface between tool and workpiece. The holder’s clamping system uses an M8×22 clamping screw and a 6 mm Allen key for secure tightening, supporting high repeatability across successive workpieces. The overall weight of 1.279 kg contributes to damping during parting operations, which helps preserve insert life and maintain surface finish, while the solid construction reduces the need for frequent re‑adjustment. Reach and cutting control for deeper grooves With an overall length of 170 mm and a cutting‑head width of 32 mm, the holder accommodates deeper parting operations up to a maximum cutting depth of 30 mm and a cutting width of 8 mm. This geometry enables controlled chip formation and stable cutting forces in narrow grooves, which is especially beneficial when machining prismatic parts or when precise part separation is required. The design also supports predictable tool behaviour, making cycle planning and downstream handling simpler. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina grooving clamp holder with existing tooling systems and to discuss MGM 800 insert options — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: D621-3TM Manufacturer: Teknik Makina Product type: Grooving clamp holder Compatibility: MGM 800 indexable inserts (Korloy) Core specifications Overall length: 170 mm Weight: 1.279 kg Holder width: 25 mm Holder height: 25 mm Cutting-head width: 32 mm Maximum cutting depth: 30 mm Cutting width: 8 mm Materials & features ISO designation: 3232 Clamping screw: M8x22 Allen key: 6 mm Cutting orientation: left SKU: D621-3TM FAQ Which inserts fit this holder? The holder is designed for MGM 800 indexable inserts and is compatible with inserts from Korloy; the fit and seating match common MGM‑800 insert geometries. What is the maximum cutting depth achievable? Maximum cutting depth for this holder is 30 mm, allowing for deeper parting and grooving operations while maintaining stability. Which screw and tool are required for clamping? Clamping is by an M8×22 screw using a 6 mm Allen key, ensuring secure seating and straightforward maintenance. Is this holder left‑hand or right‑hand oriented? This grooving clamp holder is specified for left‑hand cutting orientation, suitable for workflows requiring a left‑facing toolpath. Can this holder be used for heavy‑duty parting? The robust 25 × 25 mm clamping area, solid mass and precise ISO interface provide good vibration control for demanding parting tasks in compatible setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precision clamping solution that combines secure indexable insert compatibility, a left‑hand cutting orientation and robust construction for steady turning operations; order via Metav Werkzeuge or consult the technical team for assistance. DDHNL 3232 clamping holder — left‑hand, for DN-- 1506 indexable inserts by Teknik Makina DDHNL 3232 clamping holder designed for left‑hand turning applications; suitable for DN-- 1506 indexable inserts and engineered for repeatable clamping accuracy. Left‑hand cutting orientation for turning operations Compatible with DN-- 1506 indexable inserts ISO DDHNL 3232 form for standardised integration Robust construction, 1.29 kg for stable machining Faster setup and predictable machining results The holder ensures efficient changeovers and consistent tool positioning: its ISO DDHNL 3232 form factor allows straightforward integration into existing tool posts and fixtures, reducing set‑up time. The clamp accepts DN-- 1506 indexable inserts, eliminating the need for custom tooling and enabling fast insert replacement. With a P15 shank designation, the unit matches common holder mounts so spindle and turret compatibility is simplified. These characteristics translate directly into higher process throughput and fewer interruptions on the shop floor. Stable clamping for improved surface quality Constructed for rigidity, the tool body and clamping interface deliver steady support during cut engagement, which helps to reduce vibration and the risk of chatter. The cutting height 33 mm and holder height 32 mm maintain correct insert geometry relative to the workpiece, preserving tool life and surface finish. The item’s mass (1.29 kg) contributes to damping at the cutting edge, while the 107.5° cutting angle is optimised for secure engagement on typical turning tasks—particularly where left‑hand tool paths are required. Designed for practical workshop fit and longevity An overall length of 170 mm and a 40 mm cutting‑head width balance reach and rigidity, making the holder suitable for medium‑reach turning setups. The geometry supports indexable insert seating that is both accurate and resistant to loosening under load. Where shorthand terms are used: an indexable insert is a replaceable cutting tip; the holder secures that tip and transfers cutting forces into the machine. The result is predictable tool performance with lower per‑cutting‑edge cost compared with brazed tooling. Application guidance and compatibility considerations This clamping solution is particularly suitable for left‑hand turning operations in general workshop and light industrial contexts where DN-- 1506 inserts are already standardised. The unit’s P15 shank and ISO form mean it fits common tool posts and turret stations without modification. For unfamiliar specifications, technical drawings can be compared against existing setups to confirm fit; the standardised dimensions simplify procurement of matching spares and inserts, helping to streamline machine maintenance schedules. Discuss suitability and mounting options with Metav Werkzeuge’s specialists in Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com for detailed technical advice and order support Technical data Article number: D297TM Manufacturer: Teknik Makina Product: Clamping holder (DDHN for DN-- 1506 indexable inserts) ISO designation: DDHNL 3232 Facts Overall length: 170 mm Cutting height: 33 mm Holder height: 32 mm Head width: 40 mm Holder width: 32 mm Cutting angle: 107.5° Weight: 1.29 kg Special features Compatible with DN-- 1506 indexable inserts Left‑hand cutting direction Shank designation: P15 Robust construction for stable clamping FAQ Which indexable inserts are compatible with this holder? The holder is designed for DN-- 1506 indexable inserts; Teknik Makina’s DDHNL 3232 geometry secures these inserts with correct seating and clamp pressure. Is the cutting orientation left‑hand or right‑hand? This toolholder is specified for left‑hand cutting direction and is intended for left‑hand turning operations. What are the key dimensions to check for machine compatibility? Verify the overall length (170 mm), holder height (32 mm) and shank designation P15 against the machine’s tool post or turret to ensure correct fit. How does the cutting angle affect performance? The 107.5° cutting angle provides a balance between chip evacuation and insert support, helping to maintain tool life and surface finish under typical turning loads. Can the holder be used for heavy roughing passes? The robust build and mass (1.29 kg) improve stability, but heavy roughing suitability depends on machine power, insert grade and clamping torque; consult Metav Werkzeuge for application matching. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the holder's combination of precise clamping, compatibility with standard 27 ER indexable inserts and easy service using a T20 Torx key; order through Metav Werkzeuge or consult their specialists for a reliable supply from Emmerich. Clamping holder (Klemmhalter) SER 3232 — right-hand, 32 × 32 mm, for 27 ER inserts (Teknik Makina) A Clamping holder (Klemmhalter) SER 3232 engineered for right-hand external thread turning, compatible with P27-ER27 toolholders and designed for fast, repeatable set-ups. Right-hand cutting direction Holds 27 ER indexable inserts 32 × 32 mm clamping face 40 mm cutting height, 170 mm overall length Secure clamping that supports consistent thread turning The clamping holder is built to keep the tool geometry stable over extended cycles. With an ISO designation SER 3232 and a secure fastening system using an M5x18 Torx screw accessed by a T20 key, the assembly reduces micro-movement at the insert seat and thus improves repeatability. The robust construction and precise seat for 27 ER indexable inserts make the device suitable for repetitive external thread operations where dimensional consistency is essential. Reduced rework and quicker verification contribute directly to predictable process outcomes. Faster set-up and process stability for workshop throughput A clear operational benefit derives from the combination of a 32 × 32 mm clamping face, 40 mm cutting height and a 170 mm overall length: these dimensions provide the necessary clearance and rigidity for common turning set-ups while remaining compact enough for tight toolpost layouts. Compatibility with the P27-ER27 toolholder format simplifies tooling procurement and replacement, shortening changeover times. The result is a measurable improvement in cycle-to-cycle stability and reduced set-up time, which supports higher net productive time on the lathe. Practical serviceability to reduce downtime Service and on-bench handling have been considered in the holder's design: the Torx fastening arrangement allows safe, repeatable torque application with a T20 key and a standard M5x18 screw, enabling quick insert changes and maintenance. At ~1.405 kg the component strikes a balance between mass for vibration damping and manageable weight for manual handling. Supplied compatibility with the TA064 U‑plate and clear reference to the matching bar designation P27-ER27 supports straightforward integration into existing tooling systems, helping workshops maintain continuous operation with minimal adjustment. For reliable right-hand external thread machining choose the Teknik Makina clamping holder — contact Metav Werkzeuge for tailored advice and prompt delivery from Emmerich. Technical data SKU: D492TM Manufacturer: Teknik Makina ECLASS: 21181004 ISO designation: SER 3232 Compatible bar/toolholder: P27-ER27 Compatible insert type: 27 ER U-plate: TA064 Core specifications Clamping face width: 32 mm Clamping face height: 32 mm Cutting height: 40 mm Overall length: 170 mm Weight: 1.405 kg Torx key: T20 Torx screw: M5x18 Features and compatibility Right-hand cutting direction Holds 27 ER indexable inserts P27-ER27 bar compatibility TA064 U-plate fitment ISO SER 3232 designation Robust, workshop-oriented design FAQ Which inserts are compatible with this clamping holder? The clamping holder (Klemmhalter) SER 3232 accepts 27 ER indexable inserts and is specified for use with the matching P27-ER27 toolholder configuration. Is the holder suitable for right-hand external thread turning? Yes — the design states a right-hand cutting direction and is intended specifically for external thread operations in that orientation; the holder is identified as SER 3232 (SKU D492TM). What tools are required for insert changes and maintenance? Insert retention uses an M5x18 Torx screw, accessible with a T20 Torx key for secure, repeatable clamping. Can the holder be integrated into existing toolposts and bars? Integration is simplified by the holder's compatibility with P27-ER27 bars and the TA064 U-plate, allowing use with common turning tool systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; eMail: info@metav-werkzeuge.com

Take advantage of the holder's combination of rigid shank dimensions, precise 45° cutting geometry and straightforward compatibility with SNMG 1906 inserts for consistent turning performance; order or request technical advice via Metav Werkzeuge. DSSNR Clamping Holder (DSSNR 3232) — Right‑hand turning holder for SNMG 1906, 170 mm by Teknik Makina A DSSNR clamping holder engineered for right‑hand external turning with SNMG 1906 indexable inserts, aimed at stable, repeatable operations in production and workshop environments Right‑hand turning orientation Compatible with SNMG 1906 inserts 170 mm overall length for extended reach Solid 40 × 32 mm shank for stable clamping Stable clamping for repeatable turning results The holder is designed to secure SNMG 1906 indexable inserts with reliable seating and a defined 45° approach, which supports predictable chip flow and consistent cutting forces. The DSSNR 3232 form factor combines a clear insert interface with a compact head to reduce vibration; this results in improved dimensional stability on external turning operations. Technical features are explained where helpful, so the role of the 45° cutting geometry in reducing cutting forces and aiding chip evacuation is made explicit for procurement and production planning. Rigidity and reach that support precision at length With an overall length of 170 mm and a robust 40 × 32 mm shank cross‑section, the toolholder offers extended reach without a disproportionate loss of stiffness. The holder’s mass (approx. 1.383 kg) contributes to vibration damping in longer setups while the P19 shank designation facilitates secure seating in compatible toolposts. These combined properties are intended to sustain cutting stability and maintain surface quality across longer overhangs, reducing rework and maintaining throughput in serial machining. Compatibility and practical interchangeability on the shop floor Designed specifically for SNMG‑format inserts, the holder accepts the proven geometry of SNMG 1906 and aligns the insert at a 45° cutting angle for standardised turning strategies. The toolholder’s cutting edge height of 46 mm and head dimensions (32 × 32 mm) are matched to common insert heights, enabling straightforward changeovers and predictable tool offsets when integrating into CNC programmes or manual setups. Clear specification reduces setup time and simplifies tool management across mixed fleets. Integration into production workflows and maintenance advantages Right‑hand orientation and standardised dimensions allow this holder to be deployed across a variety of lathe toolposts with minimal adaptation. The compact head design supports access in confined setups while preserving the rigidity needed for fine tolerances. Routine maintenance is uncomplicated thanks to the conventional interface for SNMG inserts; familiar spare parts and proven geometries help to keep inventory lean and machine uptime high. The holder is thus conceived for pragmatic use in industrial turning applications where repeatability and tool life matter. Contact Metav Werkzeuge for supply and technical matching of Teknik Cutting Tools' DSSNR 3232 clamping holder (SKU D206TM); consultants are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: D206TM Manufacturer: Teknik Makina Type: DSSNR for SNMG indexable inserts Brand: Teknik Cutting Tools ISO designation: DSSNR 3232 Facts Overall length: 170 mm Weight: 1.383 kg Cutting direction: Right‑hand Cutting/approach angle: 45° Holder height: 32 mm Head width: 32 mm Holder width: 40 mm Cutting edge height: 46 mm Special features Compatible inserts: SNMG 1906 Shank designation: P19 Right‑hand turning orientation Compact head for improved access FAQ What inserts fit this DSSNR holder? The holder is compatible with SNMG 1906 indexable inserts; the interface and head geometry are matched to that insert family for predictable seating and repeatable positioning. Is the holder suitable for long overhangs? With an overall length of 170 mm and a robust 40 × 32 mm shank, the holder is intended to maintain rigidity at moderate overhangs while damping vibration through its mass. What is the cutting angle and how does it affect machining? The 45° cutting angle reduces cutting forces and improves chip flow in typical external turning applications, supporting consistent surface finish and tool life. Which orientation is this toolholder made for? This DSSNR variant is manufactured for right‑hand turning operations and is designated accordingly in the technical data. How does the P19 shank designation affect mounting? The P19 shank designation indicates the compatible toolpost or clamping interface; this standard simplifies mounting in toolholders that accept that shank form. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise clamping and reliable ISO compatibility to streamline turning operations; the left‑hand design and 170 mm overall length make this holder suitable for standard DNMG 1506 applications — order directly via Metav Werkzeuge or consult our technical team for integration advice. Clamping holder PDJN for DNMG indexable inserts (Teknik Makina) — left‑hand, 170 mm The Clamping holder PDJN for DNMG indexable inserts is a left‑hand turning toolholder engineered to secure DNMG 1506 inserts for dependable external turning in workshop and production environments. For DNMG 1506 indexable inserts Left‑hand turning toolholder ISO PDJNL 3232 compatibility 170 mm overall length, 93° cutting angle Stable, precision clamping that reduces setup time The PDJN holder offers precision clamping for common DNMG indexable inserts, eliminating guesswork during tool mounting and reducing the need for repeated adjustments. Machined contact faces and a defined insert seat ensure a repeatable seating position, which translates into consistent tool geometry across batches. For production lines where cycle‑to‑cycle consistency matters, the result is fewer rejects and a more reliable surface finish. This holder is accordingly suited to shops seeking robust turning setups without complex alignment routines. Designed for left‑hand turning with clear ISO compatibility Built for left‑hand applications, this turning holder aligns insert geometry to a 93° cutting angle, providing a familiar cutting orientation for standard external turning tasks. The part is marked with the ISO designation PDJNL 3232, which clarifies interchangeability with existing tool systems and shortens procurement and replacement cycles. Compatibility with the widely used DNMG 1506 insert format simplifies tool management and supports flexible spindle arrangements in both single‑piece flow and batch production. Practical dimensions for everyday workshop use With an overall length of 170 mm and a cutting‑head width of 40 mm, the holder balances reach and rigidity for medium turning operations. The holder body height of 32 mm and an effective insert cutting height of 38 mm provide a solid support platform that withstands moderate radial and axial loads while maintaining tool posture. Its mass of 1.384 kg contributes to damping of vibration, which aids tool life and surface quality without excessive weight for rapid tool changes. Straightforward integration and mounting on P15 shanks The toolholder is prepared for a common shank designation P15, facilitating direct replacement in many turret or toolpost set‑ups. The simple clamp‑style fixing compatible with DNMG inserts allows rapid insert replacement and secure locking under cutting forces. As a result, maintenance intervals focus on insert grade and geometry rather than holder adjustments, supporting leaner toolroom routines and faster downtime recovery. For secure left‑hand turning with DNMG 1506 inserts, contact Metav Werkzeuge to discuss supply and compatibility from our Emmerich facility — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: P126TM Manufacturer: Teknik Makina ISO designation: PDJNL 3232 Compatible inserts: DNMG 1506 Orientation: left Data Overall length: 170 mm Weight: 1.384 kg Cutting angle: 93° Cutting‑head width: 40 mm Holder height: 32 mm Insert cutting height: 38 mm Special features Left‑hand turning For DNMG 1506 indexable inserts P15 shank designation Brand: Teknik Makina FAQ Which insert type fits this holder? The holder accepts DNMG 1506 indexable inserts; the PDJN design secures the insert in the standard DNMG pocket. Is this a left‑hand or right‑hand holder? This toolholder is a left‑hand version, specified for left‑hand turning tasks and marked accordingly. What is the ISO designation of the holder? The product is identified as PDJNL 3232, the ISO compatible designation for this holder geometry. What overall length and cutting angle are provided? The holder has an overall length of 170 mm and a cutting angle of 93°, suitable for typical external turning operations. Which shank or mounting designation is used? Mounting is arranged for a P15 shank designation to facilitate integration into common toolposts and turrets. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the holder's precise cutting height 40 mm and robust clamping for reliable left‑hand turning with VBMT 1604 inserts — order directly via Metav Werkzeuge or contact our consultants for compatibility advice. Klemmhalter SVJB for VBMT Indexable Inserts – SVJBL 3232, left-hand, 170 mm (Teknik Makina) The Klemmhalter is a left‑hand indexable‑insert holder designed for turning applications using VBMT 1604 inserts, providing stable clamping and accurate tool engagement in production environments Left-hand turning orientation Compatible with VBMT 1604 inserts Cutting height 40 mm for precise engagement ISO SVJBL 3232, 170 mm overall length Reliable clamping for consistent turning accuracy This toolholder delivers repeatable clamping through a compact, engineered head that secures VBMT‑style indexable inserts. The cutting height 40 mm and the near‑right cutting geometry (93° cutting angle) are specified to ensure the insert edge meets the workpiece at the intended datum, reducing set‑up time and run‑in adjustments. The integrated geometry supports stable chip formation and consistent surface finish, which is particularly advantageous for batch production and parts with tight tolerances. With a recognised ISO designation, the holder integrates into standard turning toolposts without extensive modification. Robust geometry for stable machining and easier setup Optimised dimensions enhance rigidity where it matters: the toolhead width of 40 mm and holder width of 32 mm combine with a 170 mm overall length to balance reach and stiffness. The left‑hand orientation is suited for turning operations that require infeed from the left, and the specified mass (1.37 kg) contributes to vibration damping during moderate to heavy cuts. The P16 shank designation permits straightforward mounting in compatible boring bars and toolblocks, helping to maintain concentricity and minimise deflection. These geometric choices translate into predictable tool life and fewer interruptions for re‑clamping or adjustment. Seamless integration in industrial turning setups Designed for compatibility, the holder accepts VBMT 1604 indexable inserts and carries the SVJBL 3232 ISO reference, simplifying inventory and tooling planning across workshops. The combination of standardised insert fit, a defined cutting angle and a stable clamping solution reduces the need for trial fits and long qualification runs. For procurement and planning, the product is offered through Metav Werkzeuge, whose position as a precision partner ensures reliable supply and technical consultation. The holder is therefore suitable for contract workshops, production lines and maintenance departments seeking dependable, repeatable turning performance. Contact Metav Werkzeuge for tailored technical advice on integrating this SVJB toolholder into existing setups or to verify compatibility and availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D382-1TM Manufacturer: Teknik Makina Designation: SVJB for VBMT Indexable Inserts ISO designation: SVJBL 3232 Core specifications Overall length: 170 mm Cutting height: 40 mm Holder height: 32 mm Holder width: 32 mm Cutting head width: 40 mm Cutting angle: 93° Compatible inserts: VBMT 1604 Weight: 1.37 kg Cutting direction: left Special features P16 shank designation Left‑hand orientation ISO SVJBL 3232 For VBMT indexable inserts FAQ Which insert type fits this holder? The holder is dimensioned for VBMT 1604 indexable inserts, ensuring standardised fit and predictable cutter projection for turning operations. Is this toolholder left‑hand or right‑hand? This SVJB toolholder is specified for left‑hand cutting direction to suit infeed from the left in conventional turning setups. What is the cutting height and why does it matter? A cutting height of 40 mm positions the insert at the correct centreline relative to the workpiece, which improves face finish and reduces the need for repeated height adjustments during set‑up. Which shank and mounting format does it use? The holder uses the P16 shank designation and an overall length of 170 mm, combining reach with stiffness for stable mounting in compatible toolposts and boring bars Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 32 mm cutting height, secure compatibility with WN-- 0804 indexable inserts and a rigid 170 mm overall length for stable left‑hand turning; order directly via Metav Werkzeuge or ask the Metav consultants for tailored advice. Klemmhalter DWLNL 3232 — clamping toolholder for left‑hand turning, 32 mm cutting height (Teknik Makina) The Klemmhalter DWLNL 3232 is a left‑hand clamping toolholder engineered for turning operations with WN-- 0804 indexable inserts, offering a compact form and defined cutting geometry for repeatable results Left‑hand cutting orientation Compatible with WN-- 0804 inserts 32 mm cutting height for stable engagement 170 mm overall length for robust support Precision and process reliability from the geometry The toolholder delivers consistent performance thanks to its defined 95° cutting angle and 32 mm cutting height, which together ensure a reliable engagement geometry for interrupted and continuous turning operations. The specified cutting angle reduces unwanted deflection during heavy cuts, translating into improved dimensional stability and longer insert life. Specified dimensions provide a predictable setup for CAM programmers and shopfloor technicians, reducing setup time and the need for repeat adjustments. Secure clamping and insert compatibility for efficient tool changes Designed to accept WN-- 0804 indexable inserts, the holder allows fast, repeatable insert replacement and stable seating under load. The DWLNL 3232 ISO designation denotes the industry standard interface; this compatibility reduces tooling inventory complexity and supports lean tooling strategies. Mass and geometry—at approximately 1.377 kg—contribute to vibration damping, which helps maintain surface finish and extend insert life, delivering clear cost‑efficiency in production runs. Compact dimensions that support accessibility and rigidity With a 40 mm head width, 32 mm body width and 170 mm overall length, the holder balances accessibility in confined chucking situations with the rigidity necessary for heavier cuts. The compact layout permits close workpiece approach while maintaining the support needed for consistent chip formation. For workshops aiming to increase machine utilisation, this combination of compactness and stiffness supports shorter cycle times without sacrificing process security. Application guidance and workshop integration As a left‑hand toolholder for turning, the unit is particularly suited to operations where the cut is taken from the left side or where machine setup requires left‑hand tooling. The holder’s standardised interfaces and dimensions simplify documentation and spare‑part planning, enabling straightforward integration into existing toolsets. For teams standardising on proven insert geometries, the holder supports efficient inventory and predictable machining outcomes. Purchase the Teknik Cutting Tools clamping toolholder via Metav Werkzeuge for dependable left‑hand turning performance; contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for personalised technical advice and order support Technical Data Article number: D320TM Manufacturer: Teknik Makina SKU: D320TM ISO designation: DWLNL 3232 Facts Cutting height: 32 mm Head width: 40 mm Body width: 32 mm Overall length: 170 mm Weight: 1.377 kg Cutting angle: 95° Special features Fits WN-- 0804 indexable inserts Left‑hand cutting orientation Designed for DWLN style indexable inserts Robust clamping interface for repeatable seating FAQ Which inserts are compatible with this holder? The holder accepts WN-- 0804 indexable inserts; the DWLNL interface ensures correct seating and repeatability for these insert types. Is the toolholder suitable for right‑hand turning? No, the unit is configured for left‑hand cutting direction and is intended for left‑hand turning applications. What is the cutting height and why does it matter? The 32 mm cutting height determines the axial position of the insert and is essential for correct tool setup and consistent tool life. How does the 95° cutting angle affect machining? A 95° cutting angle provides a favourable approach that improves stability during heavier cuts and helps reduce deflection compared with more acute geometries. What are the key dimensions to consider for machine setup? Key dimensions include the 170 mm overall length, 40 mm head width and 32 mm body width, which influence reach, clearance and rigidity during operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Secure high-performance external turning by choosing a holder that combines firm clamping, precise geometry and straightforward compatibility with common indexable inserts; the robust design and ISO PCLNR designation support repeatable setups. Order the clamping holder directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. PCLN clamping holder for CNMG indexable inserts — PCLNR 3232 right‑hand toolholder by Teknik Makina A right‑hand PCLN clamping holder for CNMG indexable inserts engineered for secure external turning with a 95° cutting angle and stable tool engagement. Compatible with CNMG 1204 inserts 95° cutting angle for external turning Robust 32 mm toolholder height ISO designation PCLNR 3232 Consistent rigidity and repeatable clamping for turning operations The holder delivers stable clamping and defined tool geometry that reduce vibration and support consistent cutting results. Designed around the PCLNR 3232 form, the body geometry sets the insert at a 95° approach for external turning tasks, which helps maintain predictable chip flow and surface finish. The tool’s 32 mm holder height and 30 mm cutting height are selected to match standard lathe toolposts, while the reinforced head width of 40 mm gives additional moment resistance during heavier cuts. These dimensions and the precise clamp seating ensure that insert seating is repeatable from tool change to tool change, supporting higher process reliability in everyday workshop use. Faster setup and lower downtime through smart interface and handling A compact overall length of 170 mm and a clear shank designation (P12) support quick mounting and straightforward tool management on conventional toolposts. The clamping mechanism is optimised to work with CNMG 1204 inserts, so tool transitions and replacement routines remain efficient; reduced handling time contributes to higher productive uptime. At a measured weight of 1.429 kg, the holder balances robustness with manageable handling for fitment and alignment. The clear ISO designation aids logistics and procurement, simplifying ordering and spare-part matching for procurement teams and workshop managers. Application focus and safe operational practice Intended for conventional external turning applications with indexable inserts, the holder is configured as a right‑hand unit for positive cutting engagement in right‑hand turning directions. The interface and seat geometry are compatible with the widely used CNMG 1204 insert profile, allowing established insert grades to be used without modification. The design supports standard clamping procedures and predictable orientation at the tool tip, which reduces set-up errors and supports safer operation on serial production runs. For specialised requirements or unusual machine interfaces, Metav Werkzeuge’s technical documentation and advisory services can clarify fitment and best-practice assembly. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina PCLN clamping holder (SKU P134TM) and benefit from local supply and technical support provided from Emmerich Technical Data Article number: P134TM Brand: Teknik Makina Type: PCLN for CNMG indexable inserts ISO designation: PCLNR 3232 Facts Weight: 1.429 kg Overall length: 170 mm Holder height: 32 mm Cutting head width: 40 mm Cutting height: 30 mm Cutting angle: 95° Special features Compatible inserts: CNMG 1204 Cutting direction: right‑hand Shank designation: P12 FAQ What inserts fit this holder? The Teknik Makina PCLN clamping holder is designed for CNMG 1204 indexable inserts and provides the correct seating and clamping for that insert form. Is the holder right‑hand or left‑hand? This toolholder is a right‑hand unit; it is intended for turning operations with a right‑hand cutting direction. What is the ISO designation and why does it matter? The holder carries the PCLNR 3232 ISO designation, which standardises the tool geometry and simplifies compatibility checks and procurement. What are the key dimensions for machine setup? Key setup figures for the holder (SKU P134TM) include an overall length of 170 mm, holder height 32 mm and cutting head width 40 mm, all relevant when selecting a matching toolpost and clearance envelope. Can this holder be used with different CNMG insert sizes or manufacturers? The holder is specified for CNMG 1204 form inserts; equivalents from established insert manufacturers that match the CNMG 1204 geometry are generally suitable, subject to correct thickness and corner radius verification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, repeatable clamping for left-hand turning with WNMG 0804 inserts and a rigid 95° cutting angle; the robust 170 mm tool body and 32 mm clamp height ensure stable machining and consistent surface quality. Order the holder directly via Metav Werkzeuge or consult our specialists for additional guidance. Klemmhalter PWLN for WNMG Indexable Inserts — Left-hand, 95° Cutting Angle (Teknik Makina) A Klemmhalter engineered to hold WNMG 0804 indexable inserts securely for left-hand turning applications, designed for stable cuts and consistent repeatability in workshop and production environments Left-hand cutting direction compatibility For WNMG 0804 indexable inserts 95° cutting angle for versatile turning Robust 170 mm body with 32 mm clamp height Secure clamping for dependable left-hand turning The clamping system is configured to accept WNMG 0804 indexable inserts and to apply a firm hold via the ISO designation PWLNL 3232, ensuring reliable seating of the insert during machining. The left-hand orientation and the 95° cutting angle provide a defined cutting geometry that supports predictable chip flow and tool engagement. For users with limited technical background: a consistent cutting angle and secure clamping reduce chatter and uneven wear, so component tolerances are easier to maintain and rework is less frequent. Stable geometry that improves surface quality and tool life With an overall length of 170 mm, a cutting-head width of 40 mm and a body width of 32 mm, the toolholder delivers mass and geometry that contribute to vibration damping and cutting stability. The clamp height of 32 mm combined with a 38 mm cutting height produces a rigid setup that helps preserve insert life and maintain surface finish. The listed weight (1.421 kg) reflects a substantial construction that assists in reducing deflection under load; this translates into fewer interruptions for adjustments and higher first-pass yield in production. Designed for integration into workshop and production workflows The holder is specified with a shank designation P08 for secure mounting and is optimised for left-hand turning cycles commonly found in serial manufacturing and machine-shop use. Specifying this toolholder supports predictable process planning: repeatable changeover characteristics and a familiar ISO designation simplify tool lists and spare-part management. Maintenance cycles can be scheduled around verified tool stability rather than frequent troubleshooting, supporting efficient machining operations and controlled throughput. For support selecting the correct holder for left-hand turning with WNMG inserts, contact Metav Werkzeuge — Technik Makina’s PWLN clamping holder (SKU P157TM) can be ordered or discussed with our consultants via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: P157TM Manufacturer: Teknik Makina Article name: PWLN for WNMG Indexable Inserts ISO designation: PWLNL 3232 Facts Clamp height: 32 mm Cutting head width: 40 mm Body width: 32 mm Cutting height: 38 mm Cutting angle: 95° Overall length: 170 mm Weight: 1.421 kg Special features For WNMG 0804 indexable inserts Left-hand cutting direction Shank designation: P08 FAQ What insert type does this holder accept? The holder is specified for WNMG 0804 indexable inserts and is built to the ISO designation PWLNL 3232 for proper seating and clamping. Is the clamping holder suitable for left-hand turning only? Yes, the toolholder is designed for left-hand cutting direction and provides the correct geometry for corresponding turning operations. What are the key dimensions to check for machine compatibility? Relevant dimensions include an overall length of 170 mm, clamp height 32 mm, cutting-head width 40 mm and cutting height 38 mm; these determine fit and clearance in the turret or toolpost. Which shank designation is used for mounting? The holder uses the P08 shank designation for mounting and interface alignment. How does the 95° cutting angle affect application choice? The 95° cutting angle provides a sturdy cutting geometry that is well suited to general turning operations where a robust profile and predictable chip evacuation are priorities. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid holder that combines reliable left-hand cutting orientation with compatibility for DN-- 1506 indexable inserts; its defined geometry and clear ISO designation ensure stable turning results and straightforward integration into existing tool setups. Order via Metav Werkzeuge or consult our specialists for application-specific advice. Klemmhalter — DDJNR toolholder for DN-- 1506 indexable inserts, left-hand cutting (Teknik Makina) The Klemmhalter is a left-hand toolholder engineered for turning applications using DN-- 1506 indexable inserts, offering a precise cutting geometry and defined holder dimensions for reliable workshop and production use. Left-hand cutting orientation Compatible with DN-- 1506 inserts Overall length 170 mm for secure reach Cutting angle 93° for controlled engagement Consistent clamping and repeatable turning The holder’s design focuses on repeatability: compatibility with DN-- 1506 indexable inserts and a defined cutting angle of 93° deliver predictable chip flow and consistent tool engagement. The predefined geometry reduces setup variability and supports process stability in batch production. By using a standard insert family, tool changes are simplified and inventory is easier to manage, which contributes to measurable uptime improvements and fewer process deviations. Rigidity and dimensional clarity for improved surface finish With an overall length of 170 mm, a head width of 40 mm and holder body dimensions of 32 mm by 32 mm, the toolholder provides the mass and contact area necessary to damp vibration. The item’s weight of 1.345 kg supports steady cutting without speculative claims about material composition. These measurable attributes translate into reduced chatter risk and better surface quality on turned parts, particularly where dimensional accuracy matters most. Designed for left-hand turning workflows and integration Engineered around the DDJNR insert form and carrying the ISO designation DDJNL 3232, the toolholder suits left-oriented turning operations and common clamping interfaces such as the P15 shank designation. A cutting height of 35 mm positions the insert for standard centreline alignment on many lathes, aiding quick adaption into existing setups. The compact profile and clear technical data make the product straightforward to specify in CAM processes and tooling lists for production planning. For left-hand turning requirements or to confirm suitability for a specific machining task, contact Metav Werkzeuge for tailored advice and quotation — Metav Werkzeuge handles distribution and technical guidance for this Teknik Makina toolholder. Technical data SKU: D314TM Manufacturer: Teknik Makina Designation: DDJNR for DN-- Indexable Inserts ISO designation: DDJNL 3232 Dimensions & weight Overall length: 170 mm Head width: 40 mm Holder width: 32 mm Holder height: 32 mm Cutting height: 35 mm Weight: 1.345 kg Cutting angle: 93° Compatibility & orientation Compatible inserts: DN-- 1506 Cutting direction: Left Shank designation: P15 FAQ Which inserts fit this toolholder? The Klemmhalter (D314TM) is specified for DN-- 1506 indexable inserts; the DDJNR form is the referenced insert geometry for this holder. Is the holder suitable for right-hand turning? No, the data specifies a left-hand cutting orientation; the holder is intended for left-hand turning setups. What are the key dimensions to check for machine integration? Relevant dimensions include overall length 170 mm, head width 40 mm, holder width and height 32 mm, and a cutting height of 35 mm. What is the ISO designation and why does it matter? The ISO designation DDJNL 3232 identifies the holder form and helps match it with compatible toolposts and clamping fixtures. Is information available on the shank interface? The provided data lists a shank designation of P15; further mounting details are not specified in the data set. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, ISO‑compliant turning solution that combines a sturdy 32 × 32 mm shank with a 95° cutting angle for stable right‑hand turning. The holder’s compatibility with CN-- 1906 inserts and its 170 mm overall length support consistent tool engagement and efficient workshop workflows — order directly via Metav Werkzeuge or consult the team for application advice. DCLN for CN-- Indexable Inserts (DCLNR 3232) – Right‑hand turning toolholder by Teknik Makina, 32 × 32 mm shank DCLN for CN-- Indexable Inserts is a right‑hand turning toolholder engineered to secure CN-- 1906 indexable inserts for robust medium‑duty turning tasks Right‑hand turning configuration 95° cutting angle for sturdy engagement Shank 32 x 32 mm (ISO DCLNR 3232) Compatible with CN-- 1906 inserts Stable clamping for repeatable turning results The holder delivers reliable clamping and a defined geometry that reduces deflection during cuts. The 95° cutting angle provides a strong engagement point between insert and workpiece, which improves chip control and reduces the risk of chatter when machining with right‑hand toolpaths. Because the design focuses on consistent positioning of the insert, set‑up deviations are minimised and process reproducibility increases — a practical advantage in batch production and serial turning operations. The included ISO designation clarifies interchangeability within standard tool setups. Clear compatibility and compact dimensions for flexible use This toolholder conforms to the ISO DCLNR 3232 profile and presents a 32 × 32 mm shank, making it straightforward to integrate into existing turret or toolpost systems that accept this size. The cutting head width is 40 mm and the cutting height is 40 mm, dimensions that accommodate the CN-- 1906 insert family without additional shims or adaptations. The holder’s design supports established insert geometries, so stock management is simplified and tool inventory remains compact and predictable for the workshop. Balanced length and mass for controlled performance An overall length of 170 mm and a mass of 1.43 kg provide a balance between accessibility at the cutting point and dynamic stability. The holder’s mass contributes to vibration damping while the defined shank profile ensures secure clamping in the toolpost — together these factors help to protect insert edges and extend effective cutting life. The right‑hand configuration and the holder’s geometry allow for precise engagement angles that translate into improved surface finish and dimensional control for turned components. Installation, inventory and technical support made simple Designed for routine workshop conditions, the toolholder fits P19 designation bar systems and pairs directly with CN-- 1906 inserts, reducing the need for bespoke adapters. The clear ISO labelling and standardised dimensions speed up tool changes and simplify procurement. If further technical data or application guidance is required, assistance is available: technical enquiries and specifications can be requested by e‑mail or phone, and the Metav Werkzeuge team will advise on suitability for specific turning tasks. Contact Metav Werkzeuge today for Teknik Cutting Tools’ DCLN toolholder — expert selection advice and order support via +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: D166TM Manufacturer: Teknik Makina Type designation: DCLNR 3232 Data Shank height: 32 mm Shank width: 32 mm Cutting head width: 40 mm Cutting height: 40 mm Overall length: 170 mm Weight: 1.43 kg Cutting angle: 95° Cutting direction: right Special features Compatible with CN-- 1906 indexable inserts Fits P19 bar designation ISO‑compliant holder geometry SKU: D166TM FAQ How does the DCLN holder interface with CN-- 1906 inserts? The DCLN for CN-- Indexable Inserts secures CN-- 1906 inserts in the pocket designed for standard CN-- geometries, ensuring correct rake and clearance angles for reliable turning. Is this holder suitable for left‑hand turning? This specific holder is configured for right‑hand turning; for left‑hand operations a correspondingly configured holder should be selected. What does the ISO designation DCLNR 3232 indicate? The ISO DCLNR 3232 designation describes the holder’s profile and shank dimensions (32 × 32 mm), confirming compatibility with toolposts and turrets that accept this standard size. Will the holder fit my P19 bar system? The holder is documented with the P19 bar designation and is intended to integrate with setups that accept P19‑sized toolholders. How does the holder’s mass affect machining performance? At 1.43 kg the holder contributes to damping and stability at the cutting point, which supports consistent surface finish and reduces tendency to chatter when correctly clamped. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust right-hand clamping solution that combines secure insert retention, standard ISO compatibility and compact dimensions for smooth turning cycles; order the DCLN clamping holder via Metav Werkzeuge or consult our specialists for application-specific advice. DCLN for CN-- Indexable Inserts Klemmhalter — Right-hand turning holder with 95° cutting angle (Teknik Makina) DCLN for CN-- Indexable Inserts is a right-hand clamping holder designed for turning operations with CN-- 1606 inserts, providing stable insert fixation for precision machining. Right-hand turning holder, 95° cutting angle Accepts CN-- 1606 indexable inserts Overall length 170 mm, sturdy 32 x 40 mm head Solid construction, weight 1.407 kg Precision turning that reduces cycle variability The holder has been developed for consistent turning performance and is intended to secure indexable inserts reliably during interrupted cuts. The seating and clamping geometry are optimised for CN-- 1606 plates, so tool life is extended through reduced micro-movements at the cutting edge. A 95° cutting angle allows effective work on shoulders and facing tasks while maintaining chip control; this geometry is particularly advantageous when predictable dimensional repeatability is required in small-batch and serial production. The result is fewer reworks and a measurable improvement in throughput. Rigid construction that minimises downtime A compact overall length of 170 mm paired with a 32 x 40 mm head creates a stiff tool assembly that resists chatter and vibration. The specified 36 mm cutting height and the holder’s mass help to stabilise cutting forces; therefore, surface finish and insert life benefit directly from increased rigidity. The holder’s substantial build and the listed weight (1.407 kg) also support reliable clamping under medium to heavy feed conditions, which reduces the frequency of unscheduled adjustments and contributes to continuous production. Straightforward compatibility for fast integration Compatibility with standard insert formats and the ISO tool designation simplifies set-up and inventory management. The holder carries the ISO designation DCLNR 3232 and is intended for use with P16-type shanks, making it compatible with common turret and toolpost systems. As a right-hand tool holder, it fits standard turning sequences without special offsets; this reduces calibration time when swapping holders and supports a seamless transition into existing toolsets. The standardised geometry also makes insert replacement and reconditioning predictable and efficient. For application advice or to secure supply of Teknik Makina’s DCLN clamping holder (SKU D165TM), contact Metav Werkzeuge in Emmerich for expert guidance and dependable delivery. Technical data SKU: D165TM Manufacturer: Teknik Makina Article name: DCLN for CN-- Indexable Inserts Dimensions & weights Overall length: 170 mm Clamping head width: 40 mm Holder width: 32 mm Holder height: 32 mm Cutting height: 36 mm Cutting angle: 95° Weight: 1.407 kg Compatibility & features For CN-- 1606 indexable inserts Right-hand cutting direction ISO designation: DCLNR 3232 Toolholder shank reference: P16 FAQ What insert size is required for this holder? The DCLN clamping holder is specified for CN-- 1606 indexable inserts and is optimised to secure that plate form during turning operations. Is the holder suitable for left-hand turning? This particular variant is configured as a right-hand tool holder; left-hand operations require the corresponding mirrored version. What is the ISO designation and what does it mean? The holder’s ISO designation DCLNR 3232 indicates the shank and head form so it matches standard toolposts and fixtures designed for that geometry. Can this holder be used on standard turrets and toolposts? Yes — the geometry and the P16 shank reference enable straightforward mounting in common turret systems without custom adaptors. How does the 95° cutting angle affect machining? A 95° cutting angle offers controlled chip flow and good support for facing and shoulder cuts, improving surface finish and repeatability under varying feed conditions. What are the physical dimensions that affect tool selection? Key sizing information includes an overall length of 170 mm, head dimensions 32 x 40 mm, and a cutting height of 36 mm, which should be checked against machine installation limits. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust right-hand clamping solution that accepts DNMG 1506 inserts and provides a stable 93° cutting angle for consistent turning results; its compact 170 mm length and rigid geometry support reliable shop-floor performance. Order the clamping holder directly via Metav Werkzeuge or consult the team for technical guidance. Clamping Holder PDJN for DNMG Indexable Inserts — Right-hand turning tool holder, 93° cutting angle (Teknik Makina) The Clamping Holder PDJN for DNMG Indexable Inserts is a right-hand turning tool holder designed for use with DNMG 1506 indexable inserts in standard and demanding turning operations Right-hand turning orientation Compatible with DNMG 1506 inserts 93° cutting angle for stable cuts 170 mm overall length, robust build Stable clamping for repeatable turning outcomes The PDJN-style holder offers a secure clamping interface for DNMG 1506 inserts, ensuring repeatable seating and predictable chip flow. The ISO-style designation PDJNR 3232 indicates a standardised shank and head geometry that supports accurate insert positioning; this reduces the need for frequent adjustments and contributes directly to shorter setup times and improved process stability. The combination of a precise insert pocket and a rigid head geometry minimises micro-movements during cutting, which helps to preserve tool life and dimensional accuracy on turned components. Rigid dimensions that translate to shop-floor reliability Built with a focus on stiffness, the holder's key dimensions—32 mm shank height, 40 mm cutting-head width and 38 mm cutting height—are balanced to resist deflection under load. The overall length of 170 mm provides a practical reach without excessive overhang, while the mass of 1.384 kg contributes to damping of vibrations. These geometric characteristics make the toolholder particularly suitable where stable cutting conditions are required for consistent surface finish and chatter reduction, supporting both short production runs and repeated batch work with fewer rejects. Seamless fit into existing toolposts and straightforward handling Identified with the shank code P15 and the ISO-style reference PDJNR 3232, this holder integrates with common turret and toolpost systems used in turning centres. Its right-hand cutting orientation is matched to standard lathe tool setups and makes it straightforward to plan insert indexing and tool sequencing. The compact form factor eases storage and replacement logistics on the shop floor, while the standardised interface simplifies inventory management when combined with commonly stocked DNMG 1506 inserts. For customers requiring documented details or drawings, technical data and assistance are available through Metav Werkzeuge. For a dependable right-hand PDJN clamping solution from Teknik Cutting Tools, contact Metav Werkzeuge for purchase and technical advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: P114TM SKU: P114TM Brand: Teknik Makina Type: PDJN for DNMG indexable inserts ISO designation: PDJNR 3232 Core specifications Cutting direction: right Compatible inserts: DNMG 1506 Cutting angle: 93° Overall length: 170 mm Shank height: 32 mm Cutting-head width: 40 mm Cutting height: 38 mm Weight: 1.384 kg Special features Shank code: P15 Right-hand turning orientation Standardised ISO-style geometry FAQ Which inserts fit this holder? The clamping holder accepts DNMG 1506 indexable inserts; the holder is configured specifically for the DNMG seating geometry. Is this a right-hand or left-hand version? This version is intended for right-hand turning operations and is identified accordingly in the technical data. What does the ISO designation PDJNR 3232 mean? The PDJNR 3232 designation denotes the holder style and shank geometry; PDJN-style holders are compatible with standard toolposts and match the insert pocket for DNMG 1506. What are the key dimensions to check for machine compatibility? Key dimensions are overall length 170 mm, shank height 32 mm, cutting-head width 40 mm, and cutting height 38 mm; the holder weight is 1.384 kg. Can this holder be used for batch production and roughing cuts? The holder’s rigid geometry and 93° cutting angle provide stability suited to repetitive turning tasks and heavier cuts where a robust clamping solution is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise geometry, secure clamping and straightforward integration for reliable turning operations; order the holder directly via Metav Werkzeuge or contact our consultants for application advice. SVJCL 3232 Clamp Holder — SVJC for VCMT indexable inserts, left‑hand (Teknik Makina) The SVJCL 3232 Clamp Holder is a left‑hand turning toolholder designed to accept VCMT 1604 indexable inserts, offering a compact solution for medium‑duty external turning where repeatable clamping and stable cutting geometry are required Left‑hand orientation for specific cutting direction Holds VCMT 1604 inserts securely 32 mm holder height for stable clamping Compatible with P16 boring bar Greater process stability through defined geometry The holder's defined geometry and 93° cutting angle deliver consistent chip formation and predictable tool engagement. By accommodating triangular VCMT 1604 indexable inserts, the clamping arrangement minimises micro‑movement at the cutting edge, which in turn reduces chatter and extends insert life. This engineered stability benefits shops aiming for repeatable surface finish and tighter tolerances during serial turning operations, while the left‑hand orientation matches specific machine set‑ups and turning strategies. Robust dimensions that reduce setup time Built with a 32 mm nominal holder height, a 40 mm cutting‑head width and an overall length of 170 mm, the toolholder provides a rigid platform that simplifies set‑up and alignment. The 50 mm effective cutting height and the unit's mass (approx. 1.284 kg) contribute to vibration damping during cuts, so fewer adjustments are needed between jobs. The unit mounts to a P16 boring bar interface, enabling compatibility with common lathe tool posts and reducing the number of special carriers required in a mixed‑model production environment. Designed for compatibility and repeatable performance Integration into established tool assortments is straightforward: this clamp holder is expressly made for VCMT 1604 inserts and left‑hand machining, offering a predictable cutting direction and interface. The ISO designation SVJCL 3232 denotes the holder form factor, which helps with toolroom planning and inventory management. For operations that prioritise uptime, the simple insert change‑over and robust clamping reduce downtime and support a steady production rhythm, particularly where medium‑duty external turning is the primary task. For supply and application guidance on the SVJCL 3232 clamp holder from Teknik Makina, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific turning operations and order options Technical data Article number: D393TM Manufacturer: Teknik Makina ISO designation: SVJCL 3232 For inserts: VCMT 1604 Cutting direction: left Facts Holder height: 32 mm Cutting head width: 40 mm Holder width: 32 mm Cutting height: 50 mm Overall length: 170 mm Cutting angle: 93° Weight: 1.284 kg Features SVJC style clamp holder Compatible with P16 boring bar Left‑hand turning orientation For VCMT 1604 indexable inserts ISO form factor SVJCL 3232 FAQ Which inserts fit this holder? The SVJCL 3232 clamp holder is designed for VCMT 1604 indexable inserts and secures them in the SVJC clamping pocket for reliable engagement. Is this holder left‑hand or right‑hand? This toolholder is a left‑hand turning holder; the defined cutting direction matches left‑hand lathe operations. What are the key dimensions to check for toolpost compatibility? Key dimensions include a 32 mm holder height, 170 mm overall length and a 40 mm cutting‑head width — verify these against the machine's toolpost and the P16 mounting interface. How does the holder contribute to tool life and surface finish? By providing a rigid clamping platform and a 93° cutting angle, the holder reduces vibration and ensures stable insert engagement, which supports longer insert life and more consistent surface finish. Can this holder be used in mixed production environments? Yes, the ISO form SVJCL 3232 and the P16 mounting compatibility make it suitable for workshops that require repeatable set‑ups across a range of medium‑duty turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com