Gibt es einen Hahn und Kolb Online Shop?

Benefit from a compact, stiff design that combines an S16R 16 mm shank with a 20 mm cutting capacity and a precise 3.5 mm maximum parting depth for reliable, repeatable parting operations; order the holder directly via Metav Werkzeuge or consult the technical team for integration advice. Parting tool holder K838TM — 20 mm capacity, L 200 mm (Teknik Cutting Tools) Parting tool holder K838TM is a clamping solution for precise parting and grooving on CNC lathes and turning centres, designed to secure stable cutting performance in workshop and production environments. S16R shank with 16 mm diameter 20 mm cutting capacity, overall length 200 mm Max cutting depth 3.5 mm for precision parting Torx T8 fasteners and M2.5x7 screw for reliable clamping Precision engineering for consistent parting results The holder is built around the S16R shank format and a 16 mm shaft diameter, providing a familiar interface for standard toolposts and reduced set-up time. The 20 mm nominal cutting capacity and 11.6 mm cutting-head width translate into narrow, controlled parting cuts that limit deflection and vibration. This configuration helps to maintain surface finish and concentricity during interrupted cuts while supporting high-repeatability production runs. The design prioritises rigidity and geometric stability, which converts into fewer rejects and less rework for routine turning operations. Stable setup and predictable cutting performance With an overall length of 200 mm and a cutting height of 25 mm, the holder strikes a balance between accessibility and stiffness for medium-reach parting tasks. The documented maximum parting depth of 3.5 mm is intended for precise, shallow-to-moderate depth cuts where control is essential. At just 0.302 kg, the assembly is light enough for quick tool changes but engineered to dampen chatter when clamped correctly. Clear, measurable specifications make it straightforward to calculate tool overhang, reachable diameter and clamping torque requirements for defined machining strategies, reducing the need for trial-and-error during process setup. Practical serviceability and workshop integration Maintenance and repeatable clamping are simplified by the use of Torx T8 drive elements and the M2.5x7 fixing screw, enabling fast insert and clamp replacements with standard hand tools. As a compact parting tool holder, K838TM is ready for direct integration into existing tool posts and post-type toolholders that accept the S16R standard. The compact head geometry reduces interference for close-proximity cutting and eases access in multi-tool turrets. For supply reliability and tailored advice on fixture compatibility, Metav Werkzeuge provides local sourcing and technical consultation to support seamless workshop adoption. Arrange tailored technical advice and secure prompt delivery from Metav Werkzeuge — contact the Metav team for specification matching and ordering from Emmerich. Technical data Article number: K838TM Product: Parting tool holder Brand: Teknik Makina Facts Diameter: 20 mm Shank diameter: 16 mm Overall length: 200 mm Cutting head width: 11.6 mm Cutting height: 25 mm Max parting depth: 3.5 mm Weight: 0.302 kg Special features Shank designation: S16R Torx key: T8 Torx screw: M2.5x7 Product type: Stechklemmhalter / parting tool holder Category: Machining > Clamping holders FAQ What shank size is required for this holder? The holder uses the S16R standard and accepts a 16 mm shank format for secure mounting in compatible toolposts. What is the maximum parting depth? Maximum parting depth is 3.5 mm, suitable for controlled, precise parting and grooving operations. Which overall length should be expected when planning tool overhang? Overall length is 200 mm, which should be considered when calculating overhang to preserve rigidity. What fastening hardware is used for the clamping assembly? Clamping and service use Torx T8 drive elements and an M2.5x7 screw for reliable, repeatable tightening. Is the holder suitable for turret and post-style toolholders? The geometry and S16R shank designation make the holder compatible with standard post-style toolholders and turrets that accept the S16R format; confirm turret clearance and toolpost interface before installation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, right-hand holder that delivers narrow, repeatable grooves thanks to its 3 mm cutting width and 20 mm shank dimensions; order through Metav Werkzeuge or contact our consultants for application advice. Grooving clamp holder D773TM — right-hand parting and grooving tool by Teknik Makina The grooving clamp holder D773TM is a right-hand toolholder designed for precise parting and grooving with ISCAR 3C GRP inserts, suited to small and medium lathes where narrow cuts and stable clamping are essential. Right-hand toolholder for precise grooving Compatible with ISCAR 3C GRP inserts 20 mm shank and head width for stable clamping 3 mm cutting width for narrow parting cuts Deliver narrow, repeatable grooves for reduced rework The holder delivers consistent results for fine grooving and parting operations thanks to its 3 mm nominal cutting width and a maximum grooving depth of 18 mm. These measurable parameters support process control: narrow cuts reduce material waste and minimise the need for secondary finishing, while the defined maximum depth ensures safe engagement in a single pass where applicable. With a total length of 125 mm, the tool provides sufficient reach for common centre-turning setups without excessive overhang, contributing to predictable cycle times and consistent part quality. Rigid design for vibration dampening and longer insert life A 20 mm shank height and matching head width provide greater stiffness at the cutting zone, which limits chatter and improves surface finish. The secure clamp arrangement is engineered for stable clamping, reducing micro-movements that accelerate insert wear. The holder’s modest mass of 0.409 kg balances rigidity with manageable tool-change handling on the shop floor. As a result, toolholders of this build help extend the lifetime of indexable inserts and maintain dimensional accuracy across production batches. Simple integration with established insert systems Compatibility with ISCAR 3C GRP inserts and the ISO designation 2020 simplifies procurement and inventory management by allowing the use of widely available insert formats. The holder’s shank designation 3C-R GRP matches common lathe toolpost setups, enabling straightforward replacement of existing tooling. The right-hand cutting orientation is optimised for conventional turning directions; this predictable orientation makes process planning easier and reduces the chance of setup errors. Suited to both jobbing and small-scale production Engineered for shop-floor reliability, this clamp holder is a practical choice where precision grooves and narrow parting cuts are frequent. The combination of a compact overall length, rigid cross-section and standardised insert interface supports rapid tool swaps and straightforward maintenance routines. For facilities that aim to streamline suppliers without sacrificing capability, this holder integrates into existing workflows and contributes to steady throughput with reduced scrap rates. For tailored application support or to secure the grooving clamp holder D773TM from Teknik Makina for production use, contact Metav Werkzeuge for expert guidance and reliable supply from Emmerich. Technical Data Article number: D773TM Manufacturer: Teknik Makina Product name: Grooving clamp holder D773TM Compatible inserts: ISCAR 3C GRP Cutting direction: Right ISO designation: 2020 Facts Overall length: 125 mm Weight: 0.409 kg Cutting width: 3 mm Max grooving depth: 18 mm Shank / holder height: 20 mm Shank / head width: 20 mm Holder width: 20 mm Special features For parting and grooving applications Shank designation: 3C-R GRP Right-hand cutting orientation Suitable for ISCAR 3C GRP indexable inserts FAQ What type of inserts does this holder accept? The grooving clamp holder D773TM accepts ISCAR 3C GRP indexable inserts; the ISO reference on the holder is 2020 to match common insert formats. Is the D773TM suitable for deep grooving operations? The holder supports a maximum grooving depth of 18 mm; for deeper cuts, reassess tool engagement and machine rigidity before proceeding. Which cutting direction is this tool designed for? This holder is configured for right-hand cutting; the right-hand orientation is built into the clamp and head geometry. How does the 20 mm shank dimension benefit machining? A 20 mm shank height and head width increase stiffness at the cutting zone, reducing vibration and extending insert life in production environments. Can this holder be used in standard lathe toolposts? Yes — the shank designation 3C-R GRP and the standardised ISO 2020 interface make the holder compatible with common lathe toolpost setups and insert inventories. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise clamping, standardised insert compatibility and a compact overall length for predictable parting and grooving performance; order directly via Metav Werkzeuge or consult the specialists for machining-specific advice. Parting Tool Holder – right‑hand parting and grooving tool, ISO 2020 by Teknik Makina The Parting Tool Holder is a right‑hand clamping device for lathe parting and grooving operations, designed to accept 2C TD indexable inserts and deliver repeatable results in short‑run and batch production. Right‑hand cutting direction Compatible with 2C TD indexable inserts ISO 2020 clamping size, 20 mm dimensions 2 mm cutting width, max 16 mm cutting depth Predictable performance with standardised clamping The holder is built around the ISO 2020 clamping standard, which means a 20 mm square shank profile and widespread insert availability. This standardisation reduces downtimes associated with sourcing unusual tooling sizes and simplifies tool setup: shops benefit from consistent insert fitment and straightforward replacement. The compact 125 mm overall length and robust clamping geometry deliver a stable cutting position, improving dimensional repeatability in parting and groove operations. Optimised geometry for efficient parting and groove control A narrow 2 mm cutting width combined with a maximum 16 mm parting depth supports precise material separation while limiting cutting forces. The right‑hand orientation suits conventional lathe configurations and allows predictable chip flow when matched with the correct insert geometry. The tool’s design prioritises controlled chip evacuation and vibration damping to reduce rework and enhance surface finish, contributing to faster cycle times and fewer rejected parts. Compatibility and flexibility for workshop supply chains Designed to accept 2C TD indexable inserts and to be compatible with Taegutec insert ranges, the holder integrates into existing tooling kits without the need for special adapters. The bores and mounting geometry follow common lathe toolpost conventions, enabling quick swaps between holders. At a weight of 0.401 kg, the component is light enough for handheld handling during setup yet rigid enough for stable cutting at moderate feeds and depths. Clear advantages for purchasing and maintenance Using a standard clamping size and widely supported insert form factor lowers inventory complexity and total cost of ownership. The holder’s simple clamping screw and accessible contact surfaces make routine inspection and insert changes straightforward, reducing time at the bench. For operations focused on repeatability and predictable throughput, this clamping device offers a balance of accessibility and machining capability that supports both one‑off jobs and short production runs. For tailored advice on the Teknik Makina parting tool holder and prompt supply from Metav Werkzeuge in Emmerich, contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: D716TM Manufacturer: Teknik Makina Product: Parting tool holder SKU: D716TM Facts Clamp height: 20 mm Holder width: 20 mm Cutting head width: 20 mm Cutting width: 2 mm Max cutting depth: 16 mm Overall length: 125 mm Weight: 0.401 kg Cutting direction: right Special features Compatible with 2C TD indexable inserts Suitable for Taegutec insert types ISO 2020 clamping size Bohrstangen designation: 2C‑R TD FAQ Which inserts fit this holder? The holder accepts 2C TD indexable inserts; it is compatible with common Taegutec 2C TD insert variants. Is the holder suitable for left‑hand lathes? This version is manufactured for right‑hand cutting direction; a left‑hand variant would be required for opposite‑direction operations. What does ISO 2020 mean for everyday use? ISO 2020 denotes a 20 × 20 mm square shank and a standard insert/clamping interface, simplifying insert sourcing and ensuring interchangeability across compatible holders. How deep can the tool cut safely? The nominal maximum parting depth is 16 mm; actual safe limits depend on machine rigidity, material and insert geometry. Will this holder work on small lathes? With a compact 125 mm overall length and 0.401 kg mass, the holder suits many standard lathes; compatibility with the machine’s toolpost and clearance should be confirmed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the 5 mm cutting width, 22 mm maximum plunge depth and Horn-compatible ISO 2020 clamping for stable, repeatable parting operations; order the parting clamp holder directly via Metav Werkzeuge or contact our specialists for application advice. Teknik Makina parting clamp holder D696TM — right-hand, 5 mm cutting width A parting clamp holder for lathe grooving and parting tasks, designed for right-hand cutting and compatible with Horn inserts in ISO 2020 format Right-hand cutting direction Compatible with Horn inserts Max plunge depth 22 mm 125 mm overall length Stable seating for consistent parting quality The holder delivers a stable clamping interface thanks to its 20 x 20 mm clamping head dimensions, which reduce vibration and support a secure insert seat. That stability directly improves edge life and repeatability when separating components or grooving profiles. The cutting width 5 mm is well suited to common parting and grooving tasks, providing a balance between material removal and chip control. For workshops migrating between insert systems, the ISO 2020 format ensures straightforward replacement and familiar indexing, lowering setup time and risk of incorrect insert selection. Workflow benefits and machinability explained Engineered for efficient lathe workflows, the toolholder’s right-hand cutting orientation and max plunge depth 22 mm enable effective infeed strategies for standard parting operations. The 125 mm overall length gives a compact footprint while maintaining adequate reach for many turret and toolpost configurations; its modest 0.389 kg weight keeps inertia low for fast, precise starts and stops. The holder’s designation 5C-R S229 references the shank/bores interface used in common toolpost systems, helping workshop planners confirm mechanical compatibility with existing bar and turret setups and reduce integration time. Compatibility, installation and care made straightforward Compatibility with Horn-specified inserts simplifies procurement and ensures access to proven grades and geometries. The 2020 designation indicates an insert seat designed for 20 x 20 mm turning plates, making it clear which cutting edges fit the clamp without guesswork. Installation is straightforward when using the matching shank or mounting adapter; routine checks of clamp torque and insert seating prevent movement during heavy cuts. Regular inspection and clean seating faces deliver long-term serviceability and consistent cutting behaviour, so maintenance intervals remain predictable. For tailored advice on Teknik Cutting Tools parting clamp holders, contact Metav Werkzeuge in Emmerich by e-mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 to request SKU D696TM and discuss suitability for specific machines and materials Technical data Article number: D696TM Manufacturer: Teknik Makina Eclass: 21181005 Facts Overall length: 125 mm Weight: 0.389 kg Clamping head height: 20 mm Clamping head width: 20 mm Cutting head width: 20 mm Cutting width: 5 mm Max plunge depth: 22 mm Cutting direction: right Special features Compatible with Horn inserts ISO 2020 insert size Shank/mounting designation: 5C-R S229 SKU: D696TM Brand: Teknik Makina FAQ Which insert size fits this holder? The holder accepts inserts in the ISO 2020 size; Horn-compatible plates are recommended for optimal seating and geometry with this parting clamp holder. Is the cutting direction fixed or reversible? This parting clamp holder is configured for right-hand cutting and is intended for right-hand parting and grooving operations. What is the maximum plunge depth for heavy sectioning? Maximum plunge depth is 22 mm, allowing substantial infeed for typical parting tasks within that limit. Which shank or mounting designation is required? The holder references the 5C-R S229 mounting designation for its bar or shank interface; confirm turret or toolpost compatibility with that code. Can this holder be used for grooving aluminium and steel? Yes, the holder’s stable 20 x 20 mm clamping head and 5 mm cutting width make it suitable for grooving and parting common workshop steels and aluminium when paired with the correct insert grade. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, indexable-insert system that combines repeatable accuracy with fast insert changes; the robust 20 mm shank and six cutting edges ensure stable material removal for reliable production. Order directly via Metav Werkzeuge or consult their specialists for application advice. HF06TM Rotary Cutter – indexable-insert cutter with 20 mm shank and six cutting edges (Teknik Makina) The HF06TM rotary cutter is a compact, CNC-capable tool designed for indexable APKT 1003 inserts and general face or profile milling in industrial workshops 20 mm shank for stable clamping Accepts APKT 1003 indexable inserts Six cutting edges for smooth material removal Stable clamping for consistent machining results The compact design centres on a 20 mm shank, which provides high torsional stiffness and reduces runout compared with smaller shanks. This stability translates into repeatable machining tolerances and extended insert life, so production runs remain consistent from the first part to the last. Suitable for constrained set-ups, the robust shank diameter also simplifies toolholding logistics on standard collet or chuck systems. Efficient material removal with an indexable system Equipped for APKT 1003 indexable inserts and compatible with Korloy grades, this cutter delivers efficient cutting with predictable chip control. The arrangement of the six cutting edges and a 28 mm cutting height allows steady material removal while keeping cutting forces balanced. For workshops moving from solid-tool strategies to indexable systems, the result is lower machining costs per part and quicker on-machine insert changes. Compact overall length for flexible mounting With a 120 mm overall length and a nominal diameter of 20 mm, the tool is designed to fit tight work envelopes without sacrificing reach. The low weight (0.265 kg) contributes to reduced spindle load and minimises unwanted vibration at higher spindle speeds. This compact footprint makes the cutter a practical choice for busy CNC centres where accessibility and rigidity are equally important. Practical handling and maintenance on the shop floor Insert changes and clamping maintenance are straightforward: the cutter uses an M2.5×5.5 Torx screw and a T08 key for secure, repeatable fastening of the inserts. Clear access to the fixing screw shortens tool change time and reduces downtime. For users unfamiliar with indexable insert geometry, the system offers predictable seating and orientation, ensuring correct rake and clearance without specialist adjustments. For a tailored recommendation on the Teknik Cutting Tools HF06TM rotary cutter and quick supply from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to confirm suitability for the intended application and lead times Technical data Article number: HF06TM Manufacturer: Teknik Makina Diameter: 20 mm Shank diameter (D): 20 mm Cutting edges: 6 Cutting height: 28 mm Overall length: 120 mm Weight: 0.265 kg Accepts insert type: APKT 1003 Compatible insert manufacturer: Korloy Fixing screw: M2.5×5.5 Torx Torx key size: T08 FAQ What insert type does this cutter use? The cutter accepts APKT 1003 indexable inserts; this makes insert sourcing straightforward and compatible with Korloy grades. Is the shank suitable for standard collet systems? Yes, the 20 mm shank diameter is compatible with common collet and chuck toolholding systems for stable clamping. How many cutting edges are fitted and what is the cutting height? The tool has six cutting edges and a cutting height of 28 mm, designed for balanced material removal. Can the HF06TM be used for both face and profile milling? The cutter’s geometry and insert type make it well suited to both face and profile milling tasks in general machining. What is required for insert fastening and replacement? Insert fastening uses an M2.5×5.5 Torx screw and a T08 key for secure, repeatable changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, indexable drilling with a 20 mm cutting diameter and a compact 102 mm overall length for reliable cycle times; order directly via Metav Werkzeuge or consult the technical team for application advice. Indexable drill (20 mm) for XC-- 10T304 indexable inserts — Teknik Makina The indexable drill for XC-- 10T304 indexable inserts is a compact drilling solution engineered for efficient chip control and rapid insert changes in CNC and production workshop environments *20 mm cutting diameter *For XC-- 10T304 indexable inserts *Overall length 102 mm *Shank length 56 mm Consistent hole quality with an indexable-system design The indexable drill is built to deliver repeatable hole accuracy across medium- to high-volume production runs. With a 20 mm diameter and a 45 mm cutting length, the tool body provides stable engagement and effective chip evacuation, reducing the need for frequent rework. Compatibility with XC-- 10T304 inserts ensures that cutting geometry is maintained by a proven insert family, while the Torx fastening arrangement (M4.5x11, T15) secures the insert reliably for stable cutting forces. This configuration translates into predictable tool life and fewer unscheduled interruptions on the machine. Minimise downtime through quick insert changes and standardised components Using an indexable insert system offers a clear cost-benefit compared with solid tooling: insert changes are fast, consumable costs are easier to forecast and maintenance routines are simplified. The drill’s 56 mm shank length and balanced design support repeatable clamping and run-out control on standard tool holders, enabling quick machine set-ups. The combination of a stable body and standardised fixing hardware means insert replacement can be completed in minutes, supporting higher machine uptime and efficient production planning. Versatile fit for workshops and production lines seeking dependable performance This compact drill body suits both jobbing shops and serial manufacturers that require a robust, easy-to-service drilling solution. The construction yields a low mass of 0.33 kg, making handling straightforward during set-up while still providing the stiffness needed for demanding cycles. Supplied for use with Ceratizit inserts of the XC-- 10T304 type, the assembly supports established supply chains for inserts and spare parts, helping to maintain continuity in production and reduce lead times. Contact Metav Werkzeuge today for tailored advice and to secure the Teknik Makina indexable drill compatible with XC-- 10T304 indexable inserts Technical Data SKU: U066TM Label: 20mm Vollbohrer XC-- 10T304 L102mm Manufacturer: Teknik Makina Compatible inserts: XC-- 10T304 (Ceratizit) Torx screw: M4.5x11 Torx key: T15 Facts Diameter: 20 mm Overall length: 102 mm Cutting length: 45 mm Shank length: 56 mm Weight: 0.33 kg Special features For XC-- 10T304 indexable inserts Compatible with Ceratizit inserts Fast replacement of indexable inserts Standard Torx fastening for secure clamping FAQ What inserts does this drill use? The drill is designed for XC-- 10T304 indexable inserts and is compatible with Ceratizit insert geometries. Is the fastening hardware included and what type is it? The tool uses a Torx fastening system with a M4.5x11 screw tightened with a T15 key for secure insert clamping. Which environments is the drill suited to? This indexable drill is suitable for both small workshops and production lines where fast insert changes and consistent hole quality are required. What is the article number or SKU for ordering? Ordering reference is U066TM, listed under the Teknik Makina indexable drill for XC-- 10T304 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, internal coolant and straightforward insert compatibility for reliable, high‑throughput milling. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Teknik Makina screw-in milling cutter — 20 mm, internal coolant, for RPMT 10T3 Indexable Inserts Teknik Makina screw-in milling cutter for light to medium duty milling applications, engineered for use with RPMT 10T3 indexable inserts and equipped with integrated coolant supply for improved chip control. 20 mm diameter for compact milling Internal coolant for consistent chip evacuation Compatible with RPMT 10T3 indexable inserts M10 screw-in connection for secure mounting Precision and consistent chip control for production runs The 20 mm tool body combines a compact footprint with sufficient rigidity to maintain dimensional stability in repetitive operations. Featuring a direct screw-in mounting, the design reduces runout and vibration, which preserves tool life and contributes to consistent part quality. The cutter accepts RPMT 10T3 indexable inserts, a widely used format that simplifies stocking and replacement. Specification choices such as a moderate overall length and a low mass assist in high‑speed positional changes on modern machining centres, improving cycle-time predictability while maintaining surface finish. Integrated coolant path and robust attachment for process reliability An integrated internal coolant channel feeds coolant directly to the cutting zone, promoting efficient chip evacuation and temperature control during interrupted or continuous cuts. The holder’s M10 screw thread and a thread height of 21 mm ensure secure engagement in compatible clamping systems, while the supplied Torx screw (M3.5x8.5) and required Torx key (T15) provide straightforward assembly. Internal coolant reduces the risk of built-up edge and can extend insert life; it is particularly beneficial when using tougher workpiece materials or when running at elevated cutting speeds on automated equipment. Rapid insert change and production-friendly dimensions Designed with two cutting edges and a cutting height of 30 mm, the tool supports efficient indexable insert use and quick rotation to fresh cutting edges, minimising downtime. At a weight of 0.112 kg and with an overall length of 51 mm, the holder is easy to handle and fits compact tool magazines. The compatibility with Korloy RPMT 10T3 inserts makes replacement simple and cost-effective; indexable tooling lets shops separate the cost of the holder and the expendable inserts for improved inventory management. For identification and ordering, the article is listed as VT290TM, simplifying procurement and stock control. Discuss technical compatibility with Metav Werkzeuge’s specialists to ensure optimal application of this Teknik Makina screw-in milling cutter and arrange supply from Emmerich. Technical Data Article number: VT290TM Product type: Screw-in milling cutter Brand: Teknik Makina Compatible inserts: RPMT 10T3 Compatible insert supplier: Korloy Facts Diameter: 20 mm Overall length: 51 mm Thread height: 21 mm Cutting height: 30 mm Number of cutting edges: 2 Weight: 0.112 kg Thread: M10 Torx screw: M3.5x8.5 Torx key: T15 Special features Internal coolant For indexable inserts RPMT 10T3 Compact, low-mass holder design Quick insert indexing FAQ Which insert type fits this holder? The cutter is designed for RPMT 10T3 indexable inserts; Korloy RPMT 10T3 inserts are specified as compatible with this Teknik Makina screw-in milling cutter (SKU VT290TM). Does the tool supply coolant directly to the cutting edge? Yes, the internal coolant channel delivers coolant to the cutting zone to support chip evacuation and temperature control during cutting with the VT290TM holder. What mounting thread is required in the toolholder or arbor? A M10 screw-in connection with a 21 mm thread height is used for secure engagement with compatible clamping systems for this Teknik Makina tool. How many cutting edges are available before indexing or replacement? The holder uses indexable inserts with two cutting edges, allowing rotation to a fresh edge for fast on-machine recovery. Which tool is needed to fasten the insert screw? An M3.5x8.5 Torx screw secures the insert; the required Torx key size is T15 and is used to tighten or replace inserts on VT290TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Data inconsistency: the compatible indexable insert designation conflicts (TN--1604 vs TN--2204). Please verify the product data to ensure accuracy and prevent potential errors during application or manufacturing processes, as incorrect designations could lead to operational inefficiencies, reduced performance, or even damage to equipment. It is essential to cross-check the specifications, confirm compatibility, and consult relevant documentation or technical support if necessary to resolve the discrepancy and maintain optimal functionality.

Benefit from precise, repeatable clamping and a compact, durable design that suits high‑mix turning operations; the SRGCR 2020 clamp holder accepts RCMT 0803 indexable inserts and delivers a 30° cutting geometry for right‑hand turning — order directly via Metav Werkzeuge or consult our specialists for application advice. Clamp holder SRGCR 2020 — SRGC clamp holder for RCMT indexable inserts, 30° cutting angle (Teknik Makina) Clamp holder SRGCR 2020 is a purpose‑built turning clamp holder designed for secure seating of RCMT indexable inserts in right‑hand operations, ideal for compact tool setups and repeatable production runs SRGCR 2020 ISO designation For RCMT 0803 indexable inserts 30° cutting angle, right-hand cut Durable metalwork, 125 mm overall length Increased process reliability through robust clamping The clamp holder delivers a secure seating solution for RCMT 0803 indexable inserts, combining a precise clamping interface with a compact footprint. The SRGCR 2020 ISO designation signals standardised dimensions for predictable interchangeability across tool posts. With a 30° cutting angle and right‑hand orientation, the toolholder reduces chatter and improves surface finish in interrupted and continuous cuts. Operators and production planners benefit from consistent tool position, which shortens machine idle time caused by re‑setting and reduces scrap rates in small‑batch and serial turning. Ease of fitment and durable construction for continuous use Set‑up time is minimised by a compact, clearly dimensioned design: 125 mm overall length, 25 mm cutting‑head width and 20 mm shank width ensure straightforward positioning in common turrets and tool posts. The holder’s well‑engineered metalwork contributes to long service intervals and dependable clamping retention under varying cutting forces. At a weight of 0.411 kg, the unit balances solidity with low mass, making it suited to both manual tool changes and automated turret systems without introducing undue centrifugal load or imbalance. Geometry that supports efficient machining and tool life The 30° approach optimises chip flow and cutting load distribution for the chosen indexable insert form, allowing for stable material removal and reduced flank wear on the insert. Compatibility with RCMT 0803 inserts enables rapid index changes and straightforward inventory management when matching inserts to part requirements. The nominal cutting height of 25 mm aligns the insert nose with typical tool positions, helping to maintain correct rake and clearance angles and thereby extending insert life while preserving component tolerances. For technical guidance on integrating the Teknik Cutting Tools SRGCR 2020 into existing tooling or for order and logistics support, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our advisors provide product selection help and supply coordination from stock. Technical data Article number: D280TM ISO designation: SRGCR 2020 For inserts: RCMT 0803 Cutting direction: right Cutting angle: 30° Overall length: 125 mm Head width: 25 mm Shank width: 20 mm Cutting height: 25 mm Weight: 0.411 kg Facts 30° 125 mm 25 mm 20 mm 25 mm 0.411 kg eClass: 21181004 Special features Compatible with RCMT 0803 indexable inserts ISO: SRGCR 2020 Right‑hand cutting 30° cutting angle Brand: Teknik Makina FAQ What insert size is compatible with this clamp holder? The SRGCR 2020 clamp holder is designed for use with RCMT 0803 indexable inserts and secures them with the standard SRGC seating geometry. Is the cutting orientation right‑hand or left‑hand? This toolholder is specified for right‑hand cutting applications and is optimised for clockwise spindle rotation as typical in right‑hand turning. Which dimensions are relevant for turret mounting? Key mounting dimensions are overall length 125 mm, head width 25 mm and shank width 20 mm, which are suitable for common turret configurations. Does the holder support rapid insert changes for production runs? Yes, the ISO SRGCR interface and compatibility with RCMT 0803 inserts allow quick indexing and replacement to maintain uptime in mixed‑batch production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine reliable indexable-insert compatibility with a compact 20 mm shank and a 40 mm effective cutting length for stable, repeatable milling operations; order via Metav Werkzeuge or consult our specialists for application-specific advice. Shaft Milling Cutter S850TM — for BOMT 1304 indexable inserts, 20 mm shank (Teknik Makina) The Shaft Milling Cutter S850TM is a dedicated solid toolholder designed for precision sector milling using BOMT 1304 indexable inserts, suited to industrial steelworking and CNC applications. Compatible with BOMT 1304 indexable inserts 20 mm shank for secure toolholder fit 40 mm effective cutting length for deep cuts Torx clamping screw M3.5x8.5, key T10 Robust tool design for consistent cycle times The S850TM is engineered to maintain machining stability under repetitive load, pairing a 20 mm shank with a well-balanced geometry to reduce vibration and improve surface quality. Compatibility with BOMT 1304 indexable inserts enables flexible selection of edge grades and coatings for different steels, helping to control tool life and part finish. The two-flute configuration supports efficient chip evacuation while retaining sufficient cutting edge for medium to heavy removal tasks. As a consequence, cycle times become more predictable and process control is simplified on milling centres and machining cells. Quick clamping and fast insert replacement to minimise downtime Insert changes are secured by a Torx M3.5x8.5 clamping screw accessed with a T10 key, allowing controlled torque and repeatable seating of the insert pocket. The holder is specified to accept inserts from Ingersoll in the BOMT 1304 form, which standardises supply and reduces inventory complexity. The tool’s modest mass (approx. 0.289 kg) keeps spindle load low while providing sufficient rigidity; this balance supports longer uninterrupted runs and reduces the frequency of balancing operations. Maintenance intervals are shortened through predictable clamping behaviour and straightforward replacement routines, contributing to higher overall equipment effectiveness. Integrates into professional workshops and production lines This shaft milling cutter is suitable for workshops and production environments that demand a pragmatic combination of robustness and flexibility. The dimensional set—20 mm diameter, 40 mm cutting length, 120 mm overall length and two cutting edges—is a practical choice for general steel machining and fits standard toolholders used in small to medium-sized CNC mills. Metav Werkzeuge provides the logistical and advisory support that complements the tool: a centralised supply from Emmerich acts as a quality filter for the European market, ensuring continuity of supply and consistent part performance across batches. Discuss application requirements with Metav Werkzeuge’s specialists or request the S850TM from Metav Werkzeuge for fast, reliable supply and technical guidance from Emmerich. Technical data Article number: S850TM Manufacturer: Teknik Makina Product: Shaft milling cutter for BOMT 1304 indexable inserts Compatible inserts: BOMT 1304 Compatible insert manufacturer: Ingersoll ECLASS: 21180806 ETIM: EC011860 Facts Diameter: 20 mm Shank diameter: 20 mm Effective cutting length: 40 mm Overall length: 120 mm Cutting edges: 2 Weight: 0.289 kg Special features Torx clamping screw M3.5x8.5 Torx key size T10 Designed for indexable inserts BOMT 1304 Suited to steelworking and CNC milling applications FAQ What insert type fits this milling cutter? The cutter accepts BOMT 1304 style indexable inserts; compatibility is specified for BOMT 1304 and matching Ingersoll inserts in the S850TM holder. How is the insert secured in the holder? Insert clamping is achieved with a Torx screw (M3.5x8.5) tightened using a T10 key to ensure repeatable seating and reliable clamping force for the S850TM. Which shank diameter is required for the toolholder? The tool is manufactured with a 20 mm shank diameter and is intended for holders that accept a 20 mm shank. Is the S850TM suitable for heavy-duty milling? The S850TM combines a 20 mm shank and a 40 mm effective cutting length with a two-flute geometry; this provides a balance of rigidity and chip evacuation suitable for many medium to heavy steel milling tasks. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust, insert-based milling system that combines stable clamping and efficient chip removal for predictable cycle times. The tool’s 20 mm shank and 55 mm effective cutting length deliver steady rigidity and cutting capacity, while compatibility with RDMT 1003 indexable inserts reduces tool change downtime — order directly via Metav Werkzeuge or consult the specialists for application support. Shank cutter for RDMT 1003 indexable inserts — 20 mm shank · 2 flutes · Teknik Makina The shank cutter for RDMT 1003 indexable inserts is a precision milling tool designed for high-feed operations on CNC milling centres and machining stations. Insert-compatible RDMT 1003 system 20 mm shank for stable clamping 55 mm effective cutting length Two cutting edges for high feed rates Increased productivity through insert-based milling The insert-based design provides a clear productivity advantage: the ability to change cutting edges rapidly without removing the tool body reduces machine downtime and improves overall equipment effectiveness. With a 20 mm shank and 2 flutes, the cutter offers a balance between rigidity and chip evacuation, enabling higher feed per tooth while maintaining tool life. The measured 55 mm effective cutting length supports longer axial engagements, so fewer tool changes are required during batch runs. Secure clamping and predictable run-out for precise finishing A defined clamping diameter and solid mechanical fixing ensure consistent concentricity and low run-out, which is crucial when working to tight tolerances. The tool uses an M3.5 locking screw and a M3.5x8.5 Torx screw tightened with a T15 key, delivering reliable insert retention and repeatable seating. The resulting stability translates into improved surface finish and dimensional control, particularly on small- to medium-diameter features where vibration must be minimised. Low-maintenance handling and serviceability The modular nature of the insert system simplifies maintenance: worn inserts are replaced quickly, while the holder remains in service, reducing inventory costs for spare tools. At only 0.265 kg and with a total length of 120 mm, the cutter is light enough for efficient tool changes yet substantial enough to resist deflection during heavier cuts. Clear specifications for screw sizes and the Torx key help workshop technicians perform fast, correct servicing without guesswork. Application scope and material guidance Designed for use with RDMT 1003 indexable inserts, this shank cutter suits a range of milling tasks where consistent geometry and throughput are priorities. The two-flute geometry promotes effective chip flow at elevated feed rates, making the tool well suited to semi-finishing and finishing operations on common engineering materials. For specific material allowances and cutting data, pairing the cutter with the appropriate insert grade will determine final performance and surface quality. For tailored tooling advice or to request application data for Teknik Makina shank cutters, contact Metav Werkzeuge — our consultants will provide machining recommendations and availability from Emmerich stock Technical data Article number: R190TM Manufacturer: Teknik Makina Product designation: Shank cutter for RDMT 1003 indexable inserts EClass: 21180806 ETIM: EC011860 Shank diameter: 20 mm Effective cutting length: 55 mm Total length: 120 mm Diameter: 20 mm Cutting edges: 2 Weight: 0.265 kg Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 Compatible with RDMT 1003 indexable inserts Files (illustrations/specs): 62de7e4e33927e49dbf32747, 62de7ee4bd24461b3d5f7a6e Shop title and description available for reference SKU/UID: R190TM FAQ What insert type does this cutter accept? The shank cutter accepts RDMT 1003 indexable inserts; compatibility is central to the tool’s modular design and quick-change workflow. Which clamping and tool-retention parts are required for servicing? Servicing requires the M3.5 locking screw and M3.5x8.5 Torx screw; a T15 Torx key is used for correct tightening on the Teknik Makina shank cutter (SKU R190TM). What are the key dimensions to check before mounting? Confirm the 20 mm shank diameter, 55 mm effective cutting length and 120 mm total length to ensure correct holder fit and sufficient stick-out for the intended operation. Is the cutter suitable for high-feed milling? Yes. The two-flute geometry and insert system support elevated feed rates when combined with appropriate insert grades and machining parameters for the material. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust combination of precise dimensions and straightforward maintenance: a 20 mm shank and 80 mm cutting length deliver stable milling and long engagement for consistent chip evacuation. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. R210TM Shank Milling Cutter (Teknik Makina) — 20 mm shank for RDMT 1003 indexable inserts, 2 cutting edges A R210TM shank milling cutter engineered as a secure holder for RDMT 1003 indexable inserts, intended for reliable material removal in milling operations 20 mm shank diameter 80 mm cutting length For RDMT 1003 indexable inserts Two cutting edges for efficient cutting Faster machining with indexable inserts and long engagement The combination of a 20 mm shank and an 80 mm cutting length provides a stable connection and extended contact with the workpiece, which helps to reduce vibration and improve surface finish. Using indexable inserts means interrupted edge refreshes can be completed quickly, reducing downtime. The design supports repeatable insert seating, allowing the cutter body to retain alignment after insert changes so cycle times remain predictable and production flow stays efficient. Secure clamping and straightforward insert replacement Insert retention is engineered for reliable operation: the insert is clamped by an M3.5 locking screw, fixed with an M3.5x8.5 Torx screw, and tightened using a T15 Torx key. This familiar hardware ensures concise torque application and repeatable seating geometry. The result is a toolholder that simplifies maintenance routines — fewer steps are required to replace cutting edges, which supports quick tool changes on the shop floor and reduces non-productive time. Designed for workshop integration and consistent handling With an overall length of 200 mm and a mass of 0.477 kg, the cutter balances accessibility and handling comfort when loading into toolholders or machines. The modest weight aids manual handling during set-up, while the defined overall dimensions make the component easy to program into tooling lists and tool magazines. Clear dimensional data supports planning and inventory management for production environments where predictable tool characteristics are essential. Reliability that supports production standards The tool body is specified for RDMT 1003 inserts, offering straightforward compatibility with common insert geometries and grades. The two cutting edges focus on efficient chip removal and predictable forces during milling, which can ease clamping requirements and contribute to process stability. Regular checks of the locking screw and torque settings maintain performance and ensure the cutter continues to meet machining expectations over repeated insert changes. Contact Metav Werkzeuge today for tailored application advice and secure procurement of the Teknik Makina R210TM shank milling cutter — our Emmerich team provides local stock verification and technical guidance to support reliable integration into production Technical data Article number: R210TM Manufacturer: Teknik Makina Product name: R210TM shank milling cutter for RDMT 1003 indexable inserts Core measurements Shank diameter: 20 mm Cutting length (shank): 80 mm Total length: 200 mm Number of cutting edges: 2 Weight: 0.477 kg Features and fastening Compatible with RDMT 1003 indexable inserts Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key size: T15 FAQ Which inserts fit this cutter? The cutter accepts RDMT 1003 indexable inserts; the geometry and pocket are designed for those specific inserts to ensure correct seating and cutting performance with the R210TM shank milling cutter from Teknik Makina. How is the insert secured in the tool? An M3.5 locking screw in combination with an M3.5x8.5 Torx screw secures the insert; tightening is performed with a T15 Torx key to achieve repeatable clamping and correct seating. What are the key dimensions to check for machine compatibility? Important dimensions are the 20 mm shank diameter, 80 mm cutting length, and 200 mm total length; these values define holder fit, projection and tool magazine planning for the R210TM (Teknik Makina). Is the tool weight significant for handling or balancing? The tool weight of 0.477 kg is modest and assists manual handling during set-up; balance considerations for high-speed spindles should be reviewed with actual machine and holder combinations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, secure M6 locking and precise clamping for reliable parting and grooving operations; order the Mini parting tool clamping holder via Metav Werkzeuge or contact our consultants for application advice. Mini parting tool clamping holder – compact 20 mm body, 5 mm shank (Teknik Makina) A compact Mini parting tool clamping holder designed for space-restricted turning and grooving tasks, offering secure tool retention and easy integration into small toolposts. Compact 20 mm body for tight setups 5 mm shank for small-diameter toolholders Threaded M6 locking for secure clamping 88 mm overall length for space-saving use Improved process reliability through precise clamping The holder provides precise and repeatable clamping that reduces tool movement during parting and grooving cycles. Its compact 20 mm body and low weight contribute to lower overhang and reduced vibration, which in turn improves surface finish and extends insert life. The combination of a 5 mm shank and M6 thread for the locking screw ensures a firm mechanical connection; the result is stable cutting conditions and fewer cycle interruptions in high-mix, small-part production. Engineered for compact lathes and demanding setups Designed with confined setups in mind, the parting tool holder fits into crowded toolposts while keeping the cutting edge close to the workpiece, enabling safer and more efficient machining of small components. The 88 mm overall length helps maintain a short tooling envelope without sacrificing accessibility. Where space and repeatability matter, the compact design supports faster set-ups and reduced tool-change downtime, delivering a tangible productivity benefit on short-run and precision turning tasks. Simple compatibility and maintenance for workshop efficiency The clamping concept is intentionally straightforward to make routine checks and replacements quick. The holder’s standard M6 locking thread and common 5 mm shank diameter match widely used small tooling standards, easing retrofit into existing tool assemblies. Lightweight construction and robust geometry make maintenance uncomplicated; periodic inspection of the locking screw and clamping face is normally sufficient to keep repeatability high, so workshop throughput remains consistent without complex upkeep. For tailored advice or to secure reliable precision tooling from Teknik Makina, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss fitment and delivery options Technical data Article number: DC326TM Manufacturer: Teknik Makina Facts Body diameter: 20 mm Shank diameter: 5 mm Thread: M6 Overall length: 88 mm Weight: 0.221 kg Special features Compact design for restricted toolposts Threaded locking screw for secure clamping Low weight for reduced overhang Designed for parting and grooving tool use FAQ What shank diameter does the holder accept? The holder accepts a 5 mm shank; the Mini parting tool clamping holder is specified with a 5 mm shank diameter for small tooling applications (SKU DC326TM, Teknik Makina). Is the clamping screw a standard size? Yes, the locking screw uses an M6 thread, providing standardised replacement and straightforward sourcing for maintenance. Can this holder be used on compact CNC lathes? The compact 20 mm body and 88 mm overall length make the holder suitable for compact lathes where a short tooling envelope and stable parting are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑precision clamping solution that combines secure fixing with a small footprint for tight turning operations; order directly via Metav Werkzeuge or consult the technical team for integration advice. Mini parting clamp holder (DC306TM) – Ø20 mm body, M6 clamping screw | Teknik Cutting Tools The Mini parting clamp holder is a compact parting tool clamp engineered for small turning setups where secure clamping and minimal interference are essential Mini parting clamp holder, Ø20 mm body Clamping thread M6 for secure fixing 3 mm tool shank bore for small inserts Overall length 88 mm, lightweight 0.228 kg Secure clamping for precise parting operations The compact clamp provides precision clamping through its standard M6 fastening and a defined 3 mm bore, enabling reliable fixation of small parting blades or tool shanks. The Ø20 mm body concentrates clamping force close to the cutting edge, which reduces micro‑movement and helps to maintain repeatable cut geometry. For workshop managers and operators focused on stable performance, this minimises rework and supports consistent cycle times while preserving tool life. Space‑saving design for tight setups and easier handling With an overall length of 88 mm and a mass of just 0.228 kg, the holder is purposefully compact to fit close to the workpiece where larger fixtures would obstruct access. The reduced profile simplifies tool clearance and enables denser tool‑post configurations on small lathes and CNC turning centres. Lightweight construction reduces inertia during rapid tool changes and contributes to ergonomic handling during setup and maintenance, making the component suitable for shops seeking efficient use of turret real estate. Simple integration and dependable workshop performance The parting clamp adopts standardised interfaces—visible in the M6 clamping thread and defined diameters—so integration with existing fixtures is straightforward and predictable. The unit’s compact geometry supports short overhangs, which helps to reduce vibration in finish passes. Supplied as article number DC306TM by Teknik Cutting Tools, the design focuses on repeatability and low‑complexity installation, aiding production planning and fast tool replacement. Metav’s distribution ensures a quality filter and reliable supply from Emmerich for European workshops seeking consistent tooling availability. For compact, reliable parting clamping from Teknik Cutting Tools, contact Metav Werkzeuge for product availability and technical guidance at their Emmerich site Technical data Article number: DC306TM Manufacturer: Teknik Cutting Tools Dimensions & weight Diameter: 20 mm Overall length: 88 mm Shank bore: 3 mm Thread: M6 Weight: 0.228 kg Features & design Miniature parting clamp design Lightweight construction Compact footprint for tight setups FAQ What is the body diameter of the clamp holder? The Mini parting clamp holder features a body diameter of 20 mm (Ø20 mm). Which thread is used for the clamping screw? Clamping is secured via an M6 thread to ensure standardised fixing. What shank size does the holder accept? The holder is specified with a 3 mm bore for small tool shanks or insert holders. What is the overall length and weight of the unit? Overall length is 88 mm and the unit weighs 0.228 kg. Which article number should be referenced when ordering? Order reference is DC306TM, listed under Teknik Cutting Tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact design with a 10 mm shank and M6 clamping thread to enable secure, space-saving parting and grooving operations while maintaining high repeatability. The combination of a short overall length and low mass supports stable toolholding in tight toolposts — order directly via Metav Werkzeuge or contact our advisers for tailored guidance. Mini parting tool holder DC352TM — compact clamping holder with 10 mm shank (Teknik Makina) The Mini parting tool holder DC352TM is a compact clamping solution for precision parting and grooving on lathes, engineered for shops and jobbers that require a small, reliable toolholder for confined setups Compact 10 mm shank for tight toolposts Short 88 mm overall length for close-clearance tasks Secure M6 clamping thread for reliable fixation Low mass 0.201 kg reduces toolpost inertia Precision and stability where space is limited The DC352TM combines a 10 mm shank with an 88 mm overall length, making it ideal for applications where a reduced tool projection is essential. Its compact geometry minimises overhang, which reduces vibration and improves surface finish during parting and grooving. Designed for repetitive turning tasks, the compact holder delivers a consistent clamping interface that supports repeatable tool positioning and efficient cycle times in small-batch and maintenance operations. Secure clamping with a fine thread interface A robust M6 thread provides the clamping interface for the cutter or insert seat, offering reliable locking force without excessive clearance requirements. The fine-threaded clamp ensures that cutting edges remain steady under cutting loads, so operators experience fewer interruptions from loosening tools. This technical arrangement benefits machining accuracy and reduces rework, contributing to improved process reliability in everyday workshop use. Compatibility and practical workshop benefits The holder’s dimensions — including the 10 mm shank and a 20 mm head diameter — have been selected to match common miniature toolposts and turret stations. The low mass of 0.201 kg reduces dynamic load on the toolpost, which helps when working with smaller workpieces or when high spindle speeds are required. As a result, the toolholder supports quicker set-ups and less downtime for tool changes, delivering measurable gains in throughput for small-turning operations. Built for repeatable performance and simple integration The miniature clamping design focuses on straightforward integration into existing lathe tool arrangements: short mounting length, standard clamping thread and compact head dimensions facilitate rapid replacement of worn holders and compatibility with standard clamping fixtures. The result is less fixture rework and a shorter path from tool change to productive cutting. For workshops aiming to tighten process control and make the most of limited turret space, this holder is a rational choice that emphasises performance and longevity. Select the Teknik Makina Mini parting tool holder for compact, precise clamping and contact Metav Werkzeuge GmbH in Emmerich for expert advice and reliable supply — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: DC352TM Manufacturer: Teknik Makina Eclass: 21181005 Core dimensions Shank diameter: 10 mm Overall length: 88 mm Head diameter: 20 mm Thread: M6 Weight: 0.201 kg Features & application Miniature parting/clamping tool holder Designed for tight toolpost and turret use Secure threaded clamping for small cutting inserts FAQ What is the shank diameter of this holder? The shank diameter is 10 mm for the Teknik Makina Mini parting tool holder DC352TM, suitable for compact toolposts. Which thread is used for the clamping screw? Clamping is effected via an M6 thread on the DC352TM, providing reliable fixation for small cutters. Is this holder suitable for close-clearance operations? Yes, the short 88 mm overall length and compact head diameter make it suitable for close-clearance and confined lathe setups. How much does the holder weigh? The DC352TM has a nominal weight of 0.201 kg, helping to reduce toolpost inertia during high-speed or precise turning. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Product Information: Order Number: VT138TM Item: Modular End Mill usable with APKT 1003 Indexable Inserts the Hersteller's Korloy Brand: Teknik Makina Numbers and Data: Diameter: 20mm Cutting Edges: 3 Weight: 0.097kg Total length: 55mm Cutting Height: 35mm Thread: M10 Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑conformant toolholder that combines reliable clamping with compatibility for CNMG 1204 inserts; the right‑hand design and 95° cutting angle support stable turning operations and extended reach. Order directly via Metav Werkzeuge or contact the sales team for technical guidance. Clamping Holder PCLN for CNMG Indexable Inserts (PCLNR 2020) – Teknik Makina The Clamping Holder PCLN for CNMG Indexable Inserts is a right‑hand toolholder designed for turning applications that accept CNMG 1204 indexable inserts, delivering precise insert seating and robust clamping in workshop and production environments. Right-hand design for conventional turning Compatible with CNMG 1204 inserts 95° cutting angle for extended reach Reliable clamping and consistent cutting performance The holder delivers repeatable clamping accuracy through a proven mounting geometry, reducing insert movement during cutting and extending tool life. The 95° cutting angle improves access to shoulder areas while maintaining cutting stability. Where operators require predictable chip formation and reduced vibration, this toolholder provides a stable interface between machine and insert, helping to maintain surface finish and dimensional consistency over long production runs. Fast changeovers and broad insert compatibility Designed for standard CNMG 1204 inserts, the toolholder follows the PCLNR 2020 ISO designation to ensure interchangeability with common indexable grades and geometries. The K12 shank designation supports secure mounting in compatible toolposts and boring bars, enabling quick insert replacement and minimal downtime. This configuration simplifies inventory management, since conventional CNMG inserts from several manufacturers will seat correctly in the clamping pocket. Compact dimensions for constrained setups With an overall length of 125 mm and a cutting‑head width of 25 mm, the toolholder is compact enough for confined tooling layouts while offering a cutting height of 30 mm for proper insert alignment. The holder’s body width of 20 mm contributes to a slim profile that helps reach tight bores and close flank surfaces without compromising rigidity. The moderate weight (0.421 kg) balances mass and accessibility, supporting steady cutting without adding excessive overhang. Workshop durability and practical benefits Built for routine turning tasks, the toolholder’s right‑hand orientation and geometry deliver straightforward set‑up and predictable edge engagement. The combination of ISO conformity, compatible insert type (CNMG 1204) and standard shank specifications reduces the risk of mismatches at procurement and speeds commissioning on the shop floor. Routine maintenance focuses on insert seating and clamping screw checks, keeping life‑cycle effort minimal while ensuring continued cut quality. Contact Metav Werkzeuge today to secure the Teknik Makina PCLNR 2020 clamping holder for dependable right‑hand turning; assistance and supply are available directly from Metav Werkzeuge’s Emmerich site. Technical data Article number: P130TM Manufacturer: Teknik Makina Model designation (ISO): PCLNR 2020 Compatible inserts: CNMG 1204 Facts Weight: 0.421 kg Overall length: 125 mm Cutting height: 30 mm Holder width: 20 mm Cutting‑head width: 25 mm Cutting angle: 95° Cutting direction: Right Design / Special features Right‑hand cutting orientation Compatible with CNMG 1204 indexable inserts Shank/bar designation: K12 ISO toolholder form PCLNR 2020 FAQ What inserts fit this toolholder? The holder is designed for CNMG 1204 indexable inserts; the PCLNR 2020 pocket accepts standard CNMG insert sizes and seat geometries. Is this a right‑hand or left‑hand toolholder? This model is a right‑hand toolholder, optimised for conventional turning directions and shoulder work. What are the key dimensions to check before ordering? Verify overall length (125 mm), cutting height 30 mm and holder width 20 mm to ensure compatibility with the machine setup and toolpost. Which SKU should be ordered for this clamping holder? Order SKU P130TM for the Teknik Makina PCLNR 2020 clamping holder; Metav Werkzeuge can confirm availability and delivery options. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact design, compatibility with APKT 1003 indexable inserts and the secure shank fit to maintain steady production flow; order directly via Metav Werkzeuge or ask the consultancy team for application advice. 20 mm insert milling cutter HF37TM — for APKT 1003 indexable inserts, L100 mm (Teknik Makina) 20 mm insert milling cutter HF37TM for precision profile and slotting operations on CNC milling machines, designed to accept APKT 1003 indexable inserts for flexible edge replacement and consistent surface finish. Compact 20 mm diameter for tight profiles Compatible with APKT 1003 indexable inserts Shank diameter 20 mm for standard holders Four cutting edges for balanced cutting Maximise throughput in compact machining setups The compact 20 mm cutter diameter combined with a 100 mm overall length delivers a balance between accessibility and rigidity, enabling efficient machining in confined or detailed geometries. Fitted for APKT 1003 indexable inserts, the tool allows rapid edge changes without regrinding, which reduces machine downtime and maintains a consistent cutting geometry. With four cutting edges, chip load is distributed evenly, improving stability and enabling predictable material removal rates. These attributes translate into measurable gains in cycle-time efficiency for short-series production and precision prototyping. Simple replacement and reliable clamping for uninterrupted shifts Integration into existing toolholders is straightforward thanks to the shank diameter 20 mm, which suits common collet and chuck systems. Insert retention is achieved with a Torx screw ( M2.5x5.5 ) tightened using a T8 key, providing a secure connection while keeping replacement fast and toolroom-friendly. Compatibility with Korloy inserts supports supply-chain flexibility and cost-effective stocking. The result is a low-effort maintenance routine that keeps the cutting edge sharp and the process consistent — an operational advantage where predictable uptime is a priority. Designed for predictable results and broad workshop use Manufactured by Teknik Makina, the cutter is engineered to offer a repeatable cutting experience across a variety of common engineering materials when paired with the correct APKT insert grade. The modest mass (approx. 0.216 kg) contributes to reduced spindle load during fine profiling, while the indexed insert concept supports quick restoration of original geometry after wear. Where surface finish and repeatability matter, this insert milling solution provides a pragmatic combination of modularity and performance, suitable for metalworking shops and subcontractors aiming to consolidate tooling variety without sacrificing quality. Contact Metav Werkzeuge for tailored advice on tooling selection, availability of compatible APKT 1003 inserts and delivery from Emmerich — expert guidance ensures the right specification for each application. Technical data SKU: HF37TM Label: 20mm Igelfräser APKT 1003 L100mm Manufacturer: Teknik Makina Facts Diameter: 20 mm Overall length: 100 mm Shank diameter: 20 mm Cutting edges: 4 Weight: 0.216 kg ECLASS: 21180806 Special features Compatible with APKT 1003 indexable inserts Suitable insert manufacturer: Korloy Torx key: T8 Torx screw: M2.5x5.5 Product type: Insert milling cutter FAQ What inserts does this cutter use? The cutter is designed for APKT 1003 indexable inserts; matching grades from Korloy are suitable for a variety of materials. Is the tool compatible with standard 20 mm toolholders? Yes, the shank diameter 20 mm is compatible with common collet and chuck systems used in workshop and CNC toolholders. How many cutting edges are available and why does that matter? The tool has four cutting edges, which balances chip load and improves cutting stability for consistent surface finish. What fasteners are required for insert retention? Inserts are secured with a Torx screw (M2.5x5.5) tightened using a T8 key for reliable clamping. Who manufactures the cutter and what is the SKU? The cutter is produced by Teknik Makina and is sold under SKU HF37TM. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact clamping solution that combines precise compatibility with 16 ER indexable inserts and a robust 20 mm cutting head for reliable external threading; order via Metav Werkzeuge for prompt delivery or request specialist advice from our consultants. Clamping Holder D258TM — right‑hand holder for external threading by Teknik Makina A clamping holder D258TM designed for right‑hand external threading operations, compatible with 16 ER indexable inserts and engineered for stable clamping in lathe tool posts and turret stations Right‑hand cutting direction Compatible with 16 ER indexable inserts 20 mm cutting head width and 20 mm height 125 mm overall length Accurate thread turning with proven indexable insert compatibility The D258TM is specified for external threading and accepts 16 ER indexable inserts, allowing manufacturers to rely on standard insert geometries for consistent chip control and repeatable results. The holder’s 20 mm head width and 25 mm cutting height provide a secure seat for the insert, which reduces vibration and maintains thread form across batch runs. This leads to measurable improvements in process stability and fewer rejects when producing external threads on turned components. Compact design for fast set‑up and seamless workshop integration With an overall length of 125 mm and a mass of 0.416 kg, the tool holder is compact enough for tight tool layouts while offering sufficient reach for typical external threading tasks. The shank designation K16‑ER16 aligns the holder with common toolpost configurations, helping to limit inventory complexity and accelerate changeovers between operations. The ISO designation AL 2020 indicates a standardised geometry that supports predictable positioning and easier replacement scheduling. Practical advantages that reduce downtime and support productivity Engineered with right‑hand cutting in mind, the clamping system secures the insert firmly for high repeatability during thread cutting. The combination of standard insert compatibility and a straightforward clamp design shortens maintenance intervals and simplifies insert indexing. For production environments, this translates into lower machine idle time and clearer planning for tool life, wear allowances and reconditioning cycles — practical benefits for both single‑part jobs and serial production. For tailored selection and fast supply of Teknik Makina tooling, contact Metav Werkzeuge for specialist advice and prompt dispatch from Emmerich — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: D258TM Manufacturer: Teknik Makina ISO designation: AL 2020 Application: for external threading Cutting direction: right Facts Overall length: 125 mm Cutting head width: 20 mm Holder height: 20 mm Cutting height: 25 mm Weight: 0.416 kg Special features Compatible with 16 ER indexable inserts Shank designation: K16‑ER16 Right‑hand holder for external thread turning FAQ Is this holder compatible with standard 16 ER inserts? Yes. The clamping holder D258TM is designed for use with 16 ER indexable inserts and secures them for external threading operations. What cutting direction is the holder intended for? The tool is specified for right‑hand cutting direction, suitable for standard lathe and turret setups that require right‑hand external threading. Which shank or bar designation fits this holder? The product uses the K16‑ER16 shank designation, matching common toolpost and boring bar interfaces. What are the key dimensions to check for machine fitment? Important dimensions include an overall length of 125 mm, a cutting head width of 20 mm and a cutting height of 25 mm; the weight is 0.416 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from a robust ISO DCLNR 2020 design combined with precise compatibility for CN-- 1204 indexable inserts and a stable 95° cutting angle to maintain consistent turning quality; order directly via Metav Werkzeuge or contact our consultants for tailor‑made advice. Klemmhalter DCLN — Teknik Makina right‑hand toolholder for CN-- 1204 inserts, 95° cutting angle Klemmhalter DCLN is a right‑hand clamping holder designed for turning applications with CN-- 1204 indexable inserts; engineered for stability and repeatable tool positioning in demanding workshop environments Right‑hand turning holder DCLNR 2020 Compatible with CN-- 1204 inserts 95° cutting angle for stable cuts Robust 125 mm overall length Precision clamping that improves process stability The holder is built to keep insert position and cutting geometry constant, so cut quality and repeatability are prioritised. The DCLNR 2020 ISO designation guarantees standardised mounting for CN series inserts, while the 95° cutting angle reduces lateral forces that can induce chatter. This results in fewer reworks and a steadier machining cycle—an economic advantage for batch production and single‑piece manufacturing alike. Compact dimensions for secure fit and accessibility With a nominal overall length of 125 mm, a shank width of 20 mm and a cutting‑head width of 25 mm, the holder balances rigidity with access to tight turning positions. The 20 mm holder height and 30 mm cutting height provide the useful clearance required for multi‑tool turrets, while the modest mass of 0.441 kg lowers rotating inertia where relevant and aids quick tool changes in high‑throughput setups. These proportions help maintain tool life and surface finish consistency. Designed for routine indexable insert workflows The clamping system is optimised for CN-- 1204 indexable inserts, enabling rapid insert replacement and predictable cutting behaviour. The right‑hand orientation supports common turning directions, and the integrated shank specification K12 ensures compatibility with many tool posts. Using an indexable system like this reduces downtime for regrinding and simplifies inventory management for workshops that favour modular tooling. Practical supply and partnership advantages Sourcing from Teknik Makina via Metav Werkzeuge connects product reliability with dependable European distribution. Metav’s position as a precision partner—backed by a broad assortment and an Emmerich‑based quality filter—supports steady supply and simplified procurement. For production planners, the combination of a standardised toolholder, clear specifications and a dependable distributor reduces lead‑time risk and simplifies supplier consolidation. Choose the Teknik Makina DCLN holder for reliable, standardised turning setups and contact Metav Werkzeuge for order details or application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: D166-1TM Manufacturer: Teknik Makina Designation English: DCLN for CN-- Indexable Inserts ISO designation: DCLNR 2020 Cutting direction: right Core dimensions Overall length: 125 mm Holder height: 20 mm Holder width: 20 mm Cutting‑head width: 25 mm Cutting height: 30 mm Weight: 0.441 kg Cutting angle: 95° Features Compatible inserts: CN-- 1204 Shank designation: K12 Right‑hand orientation Indexable insert clamping system FAQ What inserts fit this toolholder? The holder accepts CN-- 1204 indexable inserts; the ISO DCLNR 2020 designation ensures correct seating and repeatable positioning for these inserts. Is the holder suitable for left‑hand turning? This toolholder is configured for right‑hand turning; left‑hand operations require the corresponding left‑hand variant. What are the key benefits of the DCLNR 2020 specification? The DCLNR 2020 standard provides a proven clamping geometry for predictable cutting angles and straightforward insert exchange, which aids consistency and reduces setup time. Can this holder be used in compact turrets? Yes—with an overall length of 125 mm and compact cross‑section dimensions, the holder is designed to fit many turret setups while maintaining rigid clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid clamping solution that shortens setup times and improves thread quality: the combination of left‑hand cutting geometry, secure mounting for 16 IR indexable inserts and a precise cutting height of 25 mm supports reliable external threading operations. Order directly via Metav Werkzeuge or contact our consultants for application advice. Clamping toolholder D268TM — for external threading, left‑hand, compatible with 16 IR inserts (Teknik Makina) Clamping toolholder D268TM for left‑hand external threading, designed for stable, repeatable performance on turning centres and lathes Left‑hand cutting for external threading Compatible with 16 IR indexable inserts ISO designation AL 2020 compatibility 125 mm overall length, compact footprint Faster, more reliable external thread turning The left‑hand geometry of this clamping toolholder enables efficient production of external threads where a left‑hand cut direction is required. Thanks to a rigid clamping concept and compact dimensions, operators benefit from reduced vibration and improved surface finish. With the toolbody engineered for stable force transmission, setup times are shortened and the likelihood of rework is lowered, delivering tangible productivity gains on batch and single‑piece work alike. Compatible interface for indexable inserts and shanks Designed to accept 16 IR indexable inserts, the holder matches common insert formats to simplify tooling logistics. The body also corresponds with the K16/IR16 shank designation, enabling straightforward integration into existing toolsets. This compatibility reduces the need for special adapters and makes the holder suitable for a broad range of turning centres and post‑holders, helping to standardise tooling across a workshop. Compact dimensions that support workshop ergonomics With an overall length of 125 mm, a head and body width of 20 mm and a cutting height of 25 mm, the clamping toolholder offers a compact footprint while preserving cutting stability. Its balanced mass (approx. 0.416 kg) eases handling during set‑up and minimises additional load on the turret. These dimensional values make the holder practical for confined setups and for machines with limited overhang, ensuring predictable chip control and consistent thread form. Practical benefits for production and maintenance The ISO designation AL 2020 indicates a standardised interface that simplifies replacement and spare management. Designed for indexable inserts, the holder supports quick insert changes that reduce machine downtime and increase effective cutting time. Where repeatability and short cycle times are priorities, the combination of standard insert sizes, compact geometry and secure clamping helps deliver measurable process stability and lower total machining costs. Contact Metav Werkzeuge today for tailored advice on implementing the Teknik Makina clamping toolholder D268TM in left‑hand external threading applications and arrange supply directly from Emmerich. Technical data Article number: D268TM Manufacturer: Teknik Makina Product: Clamping toolholder for external threading (Klemmhalter) ECLASS: 21181004 Facts Overall length: 125 mm Cutting height: 25 mm Head width: 20 mm Body width: 20 mm Body height: 20 mm Weight: 0.416 kg Special features For external threading Left‑hand cutting direction Compatible with 16 IR indexable inserts Shank / bar designation: K16‑ IR16 ISO designation: AL 2020 FAQ What insert size does the holder accept? The holder accepts 16 IR indexable inserts; the design supports common 16 IR geometries for external threading. Is the clamping toolholder suitable for left‑hand threads only? The toolholder is configured for left‑hand cutting direction, making it appropriate for left‑hand external threading operations. What are the key dimensions to check for machine compatibility? Important dimensions are 125 mm overall length, cutting height 25 mm, and a head/body width of 20 mm; these determine clearance and turret fit. Which ISO designation applies to this holder? The holder carries the ISO designation AL 2020, facilitating standardised mounting and replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the stable clamping and compact dimensions to keep turning operations precise and consistent; the left-hand orientation and 95° cutting angle make this toolholder suitable for a wide range of external turning tasks. Order the clamping holder directly via Metav Werkzeuge or request advice from their consultants. Clamping holder PWLN for WNMG Indexable Inserts – left-hand, 95° cutting angle (Teknik Makina) The Clamping holder PWLN for WNMG Indexable Inserts is a left-hand turning toolholder engineered for secure clamping of WNMG 0804 inserts in general turning and finishing operations across industry workshops and production shops Left-hand turning orientation Compatible with WNMG 0804 inserts 95° cutting angle for versatile machining Solid construction with 125 mm overall length Consistent clamping for repeatable turning accuracy The primary benefit of this toolholder is secure clamping, which reduces insert movement under cutting forces and supports repeatable part quality. The clamping concept used with this holder keeps the indexable insert firmly located so that tool life is optimised and rework is minimised. By combining a compact design with a reliable clamp interface, the holder helps to maintain consistent surface finish and dimensional accuracy across production batches. Broad compatibility and simple set-up that saves time Compatibility with WNMG 0804 inserts means easy integration into existing tooling stocks and straightforward reloading when indices are changed. The holder carries the PWLNL 2020 ISO designation, matching common tooling standards for groove and profile turning. For users unfamiliar with indexable systems: WNMG inserts are four-edged cutters that are indexed when an edge wears, so the holder’s compatible pocket and clamp geometry are essential to ensure correct positioning and repeatable cutting geometry. Robust dimensions and geometry for practical workshop use Designed with a 125 mm overall length and a 30 mm cutting height, the holder balances rigidity and access to workpieces in confined set-ups. The 25 mm cutting-head width and 20 mm body width support stable seating and help resist vibration during cutting. With a mass of 0.43 kg, the toolholder is substantial enough to damp chatter yet light enough for easy handling and changeover. The 95° cutting angle and left-hand orientation provide a neutral approach geometry that is suitable for a variety of external turning tasks where clearance and finish are priorities. Contact Metav Werkzeuge for tailored advice on compatibility and supply of the PWLN clamping holder—reliable delivery and stock information from Emmerich are available on request. Technical data Article number (SKU): P155TM Manufacturer: Teknik Makina Designation: PWLN for WNMG Indexable Inserts Facts Holder height: 20 mm Cutting-head width: 25 mm Holder body width: 20 mm Cutting height: 30 mm Weight: 0.43 kg Cutting angle: 95° Overall length: 125 mm Cutting direction: left Features ISO designation: PWLNL 2020 Suitable for WNMG 0804 inserts Shank designation: K08 Left-hand turning toolholder Compact, rigid construction FAQ Which inserts fit this toolholder? The clamping holder is specified for WNMG 0804 indexable inserts; the pocket and clamp geometry are matched to that insert size for correct seating and indexing. What does the 95° cutting angle mean in practice? A 95° cutting angle provides a near-neutral approach that balances clearance and strength at the cutting edge, suiting general external turning where a stable tool orientation is required. Is the holder suitable for finishing or roughing operations? The holder’s rigid construction and secure clamping make it well suited to finishing and medium-duty turning; for heavy roughing, insert grade and cutting parameters should be chosen accordingly. How is the left-hand orientation applied on the lathe? Left-hand orientation indicates the holder is arranged for turning where the cutting action proceeds in the opposite direction to a right-hand tool; the left-hand setup must match the machine and operation plan to ensure correct chip flow and tool clearance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Strong clamping and proven compatibility with VCMT 1604 indexable inserts deliver stable turning and reduced rework; the compact 125 mm overall length and 20 mm shank improve access in confined setups. Order the clamping holder directly via Metav Werkzeuge or ask our consultants if specialised machining data is required. SVVCN 2020 Clamping Holder (for VCMT 1604) — Teknik Makina The SVVCN 2020 clamping holder is a neutral-direction turning holder for VCMT 1604 indexable inserts, engineered to secure inserts reliably in medium-duty lathe operations. ISO SVVCN 2020 toolholder designation Compatible with VCMT 1604 indexable inserts 20 mm shank width for stable support Neutral cutting direction for versatile turning Consistent clamping for predictable machining results The holder’s core function is secure and repeatable insert seating, which translates directly into consistent surface finish and fewer adjustment cycles. The SVVCN 2020 configuration accommodates standard indexable inserts, notably the VCMT 1604, delivering a reliable cutting interface that reduces micro-movement under load. With a modest mass of 0.373 kg, the unit balances rigidity with manageable tool change ergonomics, supporting steady spindle loads and predictable tool life. For operations where reproducibility matters, this toolholder offers measurable process stability. Accessible form factor that shortens setup time A compact footprint eases access to complex workpieces: the 125 mm overall length combined with a 20 mm shank and 10 mm cutting head width provides a low-profile mounting that keeps the cutting edge close to the workpiece in tight lathe stations. The specified 72.5° cutting angle promotes favourable engagement geometry, improving chip flow and clearance for many turning tasks. These dimensional choices reduce setup iterations and allow quicker insert replacement, so fewer machine minutes are lost to tool handling and more are spent on production. Versatile compatibility that supports workshop efficiency Designed for neutral cutting direction, the holder integrates with common turning strategies and minimises the number of specialised tools required on the trolley. Acceptance of standard VCMT 1604 inserts means disposables are widely available and familiar to most workshops, lowering inventory complexity. The indexable insert system itself supplies a cost-efficient path to fresh cutting edges without full-tool replacement, contributing to lower per-part tooling costs and a simpler maintenance routine. Choose Teknik Makina’s SVVCN 2020 clamping holder for reliable insert clamping and contact Metav Werkzeuge for tailored technical advice and order facilitation at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: D150TM Brand: Teknik Makina Designation: Clamping holder (SVVCN 2020) Secondary designation: SVVCN for VC-- Indexable Inserts ECLASS: 21181004 Facts Shank width: 20 mm Cutting head width: 10 mm Cutting height: 35 mm Overall length: 125 mm Weight: 0.373 kg Cutting angle: 72.5° Special features Compatible inserts: VCMT 1604 Cutting direction: neutral ISO designation: SVVCN 2020 Toolholder type: indexable insert clamping Toolholder seat: bohrstangen designation K16 FAQ What inserts fit this holder? The SVVCN 2020 clamping holder accepts VCMT 1604 indexable inserts as specified, offering a standard insert interface for routine turning tasks. Is the holder suitable for left- or right-hand turning? The holder is configured for a neutral cutting direction, so the SVVCN 2020 can be used in setups where a neutral or general-purpose approach is required. How does the 72.5° cutting angle affect performance? The 72.5° cutting angle on the SVVCN 2020 provides favourable clearance and engagement geometry, helping chip evacuation and consistent contact for many turning operations. Will this holder fit compact lathe stations? With a 125 mm overall length and a low-profile head, the SVVCN 2020 is designed to improve access in tighter machine configurations while maintaining stable clamping. How much does the toolholder weigh and does that affect changeover? The SVVCN 2020 weighs 0.373 kg, a balance that keeps the holder rigid under cutting loads while remaining easy to handle during insert replacement and tool changes. Which bores or toolposts are compatible with this holder? The holder references a bohrstangen designation K16, which should be matched to corresponding toolposts or adaptors to ensure correct seating and clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise clamping, through-tool coolant and a compact 20 × 20 mm shank for consistent turning results; order the holder directly via Metav Werkzeuge or ask the consultants for application advice. Klemmhalter AP507TM — SCLC toolholder for CCMT 1204, left-hand, internal coolant (Teknik Makina) A Klemmhalter AP507TM: a left-hand SCLC toolholder designed for turning with CCMT 1204 indexable inserts, offering through-tool coolant and a compact profile for reliable workshop integration. SCLC toolholder for CCMT 1204 inserts Left-hand cutting direction, 95° approach angle Internal coolant for reliable chip evacuation Compact 20 × 20 mm shank, 125 mm overall length Consistent machining through secure clamping and coolant The AP507TM is built around the SCLCL 2020 ISO form and is compatible with CCMT 1204 indexable inserts, delivering repeatable seating and stable cutting forces. The integrated internal coolant channel reduces heat at the cutting edge and improves chip evacuation, which in turn helps to prolong insert life and maintain surface finish. With an approach angle of 95°, the holder provides a practical compromise between strength and accessibility for shoulder and facing operations, helping to maintain cycle-time consistency on series production runs. Compact dimensions and robust fastening for workshop efficiency A compact 20 × 20 mm shank and a total length of 125 mm allow the tool to fit standard toolposts while preserving a rigid support for moderate overhangs. Fastening is secured via a Torx M4x11 screw (Torx key T15) and a clamping plate fixed with an M6 screw to the TA015-1 carrier, providing a straightforward assembly routine and consistent clamping torque. At 0.38 kg the holder is easy to handle during tool changes yet solid enough to minimise vibration, which supports better tool life and fewer touch-ups between batches. Practical fitment and application guidance for turning operations Designed specifically for left-hand cut applications, the AP507TM suits turning tasks where tool approach from the left is required; its construction is therefore recommended where directional cutting forces and chip flow demand defined orientation. The holder accepts commonly used CCMT inserts, a standard choice for finishing and general-purpose turning, allowing familiar insert geometries to be used without special tooling adaptations. Maintenance is straightforward: periodic inspection of the coolant path and torx clamping screw ensures consistent performance and prevents chip build-up in the coolant bore. Contact Metav Werkzeuge today for tailored advice on integrating the Teknik Makina AP507TM SCLC toolholder with internal coolant into the production line and to arrange supply or application consulting Technical data Article number: AP507TM Manufacturer: Teknik Makina Designation: Klemmhalter / SCLC for CCMT indexable inserts SKU: AP507TM Facts Shank width: 20 mm Shank height: 20 mm Cutting head width: 25 mm Cutting height: 30 mm Overall length: 125 mm Overall height: 20 mm Weight: 0.38 kg Approach angle: 95° Screw sizes: M6; Torx screw M4x11 Special features ISO designation SCLCL 2020 Compatible with CCMT 1204 indexable inserts Internal coolant (through-tool) Left-hand cutting direction U-plate: TA015-1 Torx key size: T15 FAQ What inserts fit the AP507TM clamping holder? The AP507TM is designed for CCMT 1204 indexable inserts; the SCLCL 2020 interface accepts the standard CCMT geometry used for general turning tasks. Is the holder suitable for through-tool coolant systems? Yes, the Teknik Makina AP507TM features internal coolant, enabling coolant to reach the insert zone for improved chip control and thermal management. Which shank size is required for mounting this holder? The toolholder uses a compact 20 × 20 mm shank profile and an overall length of 125 mm, matching common small to medium toolpost setups. What fastening hardware is specified for the clamping mechanism? Clamping is secured with a Torx M4x11 screw (Torx key T15) and the U-plate is fixed via an M6 screw to the TA015-1 plate for repeatable clamping performance. Is the AP507TM available for right-hand cutting? This SKU (AP507TM) is specified for left-hand cutting; for right-hand versions, consult Metav Werkzeuge for alternative part numbers or compatible holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com