Gibt es einen Hahn und Kolb Online Shop?

Benefit from a secure S20S SCLCL shank, 25 mm diameter and full compatibility with CC-- 09T3 indexable inserts; order via Metav Werkzeuge or consult their specialists for machine matching and supply from Emmerich. Boring bar SCLC for CC-- Indexable Inserts (S20S SCLCL) — 25 mm, 250 mm The boring bar SCLC for CC-- Indexable Inserts is a left‑hand turning tool holder designed for use with CC-- 09T3 indexable inserts in medium‑duty turning and boring operations. S20S SCLCL shank for secure clamping Compatible with CC-- 09T3 indexable inserts Left-hand cutting orientation 95° cutting angle for reliable chip control Precision clamping for consistent results The S20S SCLCL designation identifies a standardised shank and head geometry that ensures stable seating in suitable tool posts and turrets; this leads to repeatable tool positioning and reduced vibration. With the ISO code S20S SCLCL, the holder is engineered for consistent clamping force and minimal runout, which translates into improved surface finish and tool life when used with compatible indexable inserts. Compact dimensions that simplify setup With a nominal diameter: 25 mm and an overall length of 250 mm, the tool balances reach and rigidity to suit many workshop setups. The shank diameter: 20 mm permits snug mounting in smaller toolholders while the cutting height: 40 mm aligns insert geometry for predictable engagement. These dimensions reduce the need for extensive tool offset adjustments and make the component straightforward to integrate into existing turning routines. Cutting geometry optimised for chip control A 95° cutting angle combined with a left‑hand cutting orientation delivers effective chip formation and evacuation in conventional turning operations where left‑hand approach is required. The configuration is particularly helpful when machining features that benefit from controlled chip flow, reducing the likelihood of rework and increasing process reliability when matched with appropriate CC-- 09T3 inserts. Reliable sourcing and workshop compatibility Supplied in a compact, robust format and weighing approximately 0.612 kg, the tool is suitable for standard lathe toolholders that accept the S20S profile. Sourcing through Metav Werkzeuge ensures access to a wide range of compatible inserts and accessories from a central European distribution point that acts as a quality filter for the market. This arrangement supports uninterrupted supply and clear product specification for procurement and production planning. Contact Metav Werkzeuge in Emmerich for tailored advice and reliable delivery from stock: info@metav-werkzeuge.com • +49 2822 7131930 — reference SKU K245TM for quicker handling Technical Data SKU: K245TM Manufacturer: Teknik Makina Designation: Bohrstange Type: SCLC for CC-- Indexable Inserts ISO designation: S20S SCLCL Core dimensions Diameter: 25 mm Overall length: 250 mm Shank diameter: 20 mm Cutting height: 40 mm Weight: 0.612 kg Cutting angle: 95° Cutting direction: left Special features Compatible with CC-- 09T3 indexable inserts S20S SCLCL shank geometry Holder code: 09 FAQ Which indexable inserts fit this holder? The boring bar accepts CC-- 09T3 indexable inserts; these are the specified insert format for this SCLC holder (SKU K245TM). What is the ISO designation for the tool? The ISO designation is S20S SCLCL, indicating the shank and head form for standard toolholder compatibility. What are the key dimensions to check for machine integration? Key dimensions: diameter 25 mm, overall length 250 mm, shank diameter 20 mm, cutting height 40 mm, weight 0.612 kg. Is the cutting orientation left‑hand or right‑hand? This holder is configured for left‑hand cutting orientation. What cutting angle does the holder present at the insert seat? The insert seat provides a 95° cutting angle for effective chip control in turning applications. Which holder code corresponds to the clamping interface? The clamping interface designation provided in the data is 09. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust right-hand S25R SCLCR boring bar with a 25 mm cutting diameter and 200 mm overall length for consistent external turning; compatible with CC-- 09T3 indexable inserts for flexible tooling and straightforward replacement — order directly via Metav Werkzeuge or consult our specialists for application guidance. Bohrstange — S25R SCLCR boring bar, 25 mm diameter, right-hand (Teknik Makina) The Bohrstange is a right-hand boring bar engineered for external turning with CC-- 09T3 indexable inserts, suitable for workshop and production environments where stability and quick insert changes matter Right-hand S25R SCLCR design 25 mm cutting diameter Compatible with CC-- 09T3 inserts 200 mm overall length, 32 mm shank Greater rigidity for accurate turning results The S25R SCLCR configuration delivers improved stiffness through a substantial 32 mm shank, which reduces tool deflection during cutting. For external turning operations, this enhanced rigidity translates into repeatable diameters and better surface finish, reducing rework and scrap rates. The tool’s 25 mm diameter and the 200 mm overall length are balanced to provide reach without sacrificing stability, making the bar suitable for a broad range of turning tasks where consistent concentricity is required. Flexible insert compatibility for lower tooling costs Designed for use with CC-- 09T3 indexable inserts, the boring bar enables rapid insert changes and compatibility with commonly available insert grades. Using indexable cutting tips minimises downtime for regrinding and supports a predictable tooling budget: worn inserts can be replaced in seconds rather than replacing the whole tool. The 95° cutting angle provides a secure seating geometry for the insert, ensuring reliable chip control and extended insert life when paired with appropriate grades for the workpiece material. Efficient setup and predictable handling in the workshop The bar’s ISO designation S25R SCLCR simplifies selection and toolholder matching in CNC tool magazines and manual toolposts. The specified cutting height 40 mm and the shank sizing ensure compatibility with standard clamping systems, while the right-hand cutting direction matches common turning cycles. At a weight of 0.694 kg, the assembly is easy to handle during setup, yet substantial enough to maintain a solid cutting stance. These dimensions contribute to faster set-ups and fewer adjustments between jobs. Practical benefits for production and maintenance Using a standardised boring bar like this one reduces complexity across tool inventories: a single shank and insert system supports multiple diameters and operations. The ability to fit indexable inserts means that different grades can be selected for aluminium, steel or harder alloys (subject to insert grade selection), offering process flexibility without changing the basic tool. Overall, the bar is an efficient, serviceable solution for shops focused on throughput and consistent component quality. For robust external turning applications, choose Teknik Makina’s S25R SCLCR boring bar and contact Metav Werkzeuge in Emmerich for hands-on advice, availability and supply at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: K116TM Manufacturer: Teknik Makina ISO designation: S25R SCLCR Type: SCLC for CC-- Indexable Inserts Cutting direction: right Numbers / Core technical data Diameter: 25 mm Overall length: 200 mm Shank diameter: 32 mm Cutting height: 40 mm Cutting angle: 95° Weight: 0.694 kg Designs / Special features Compatible with CC-- 09T3 indexable inserts SCLC style for indexable insert turning Shaft designation: 09 Right-hand cutting configuration FAQ Which insert type fits this boring bar? The boring bar accepts CC-- 09T3 indexable inserts; the SCLC geometry secures the insert for stable external turning. Is this a right-hand or left-hand tool? This tool is configured for right-hand cutting, indicated by the S25R SCLCR ISO designation. What are the key dimensions to check for my turret? Check the 25 mm cutting diameter, 200 mm overall length and 32 mm shank diameter to ensure correct fit in the turret or toolholder. How does the 95° cutting angle affect performance? The 95° cutting angle provides secure insert seating and supports effective chip control, which can improve surface finish under stable cutting conditions. Can the bar be used for long-reach turning? The 200 mm overall length offers reach for many external applications while maintaining rigidity; for extended reach needs, assess deflection risk relative to the shank diameter. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of high rigidity, compatibility with CC‑1204 indexable inserts and a 32 mm shank for dependable toolholding; the result is consistent turning performance and reduced setup time. Order the Bohrstange (SCLC for CC-- Indexable Inserts) directly via (Metav Werkzeuge) or ask our consultants if needed. Bohrstange — SCLC boring bar (S25S SCLCR) by Teknik Makina, 32 mm shank, 250 mm overall The Bohrstange (S25S SCLCR) is a right‑hand boring bar for turning applications, designed for use with CC‑1204 indexable inserts and engineered for stable, medium‑duty metal removal. S25S SCLCR ISO designation Compatible with CC‑1204 indexable inserts 32 mm shank for secure clamping 250 mm overall length for extended reach Stable toolholding for accurate, repeatable turning The boring bar is built to deliver consistent machining stability through a robust shank and optimised geometry. The S25S SCLCR ISO designation signals a standardised mount and cutting orientation, while the 32 mm shank provides secure clamping in standard toolholders, reducing vibration and improving surface finish. For operations where repeatability and tight tolerances matter, the improved rigidity directly reduces rework rates and cycle‑time variability. Fast insert changes and compatible system reduce downtime Engineered for indexable inserts (CC‑1204), this tool simplifies tool management: insert replacement is quicker than resharpening, and the common insert format eases inventory handling across multiple machines. The moderate cutting angle (95°) and right‑hand cutting direction suit a wide range of external turning and facing tasks, enabling a balance between metal removal rate and edge life. The combined effect is fewer machine stops and a more economical production rhythm. Industrial readiness and integration into workshop systems With a 250 mm overall length and a nominal diameter of 25 mm, the boring bar gives added reach for deeper cuts while keeping clearance issues minimal. The tool’s 0.965 kg mass contributes to steady momentum without excessive load on spindles. Marked with familiar technical descriptors and compatible with standard holders, the item integrates smoothly into existing CNC setups and manual lathes, supporting predictable cycle planning and easier tooling lists. Practical benefits for procurement and maintenance Standardised features such as the ISO designation and widely used insert type streamline purchasing and reduce the number of specialised spares required. The use of indexable cutting edges lowers lifecycle costs through rapid replacement and predictable wear patterns, which in turn supports maintenance scheduling and tool‑room efficiency. The combination of robust shank design and standard insert compatibility maximises uptime across small and medium production batches. Contact Metav Werkzeuge for availability, a technical quotation or clarification on suitability for specific turning tasks; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: K116-1TM Manufacturer: Teknik Makina ISO designation: S25S SCLCR SKU: K116-1TM Facts Shank diameter: 32 mm Overall length: 250 mm Diameter: 25 mm Cutting height: 45 mm Weight: 0.965 kg Cutting angle: 95° Cutting direction: right Special features Compatible with CC‑1204 indexable inserts For indexable insert turning applications Suitable for standard toolholders Brand: Teknik Makina FAQ Which insert type fits this boring bar? The boring bar is compatible with CC‑1204 indexable inserts and is designed to accept that insert format for quick replacements. Is the shank suitable for common toolholders? The 32 mm shank diameter provides a secure fit in standard toolholders; the ISO designation S25S SCLCR clarifies the mounting and orientation. Can this tool be used for deep‑reach turning? With a 250 mm overall length and a 25 mm tool diameter, the boring bar is suited to moderate deep‑reach turning while maintaining stability. Does the bar cut left or right? This tool is configured for right‑hand cutting, matching typical right‑hand turning operations on lathes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑stability solution for internal turning: the combination of a 25 mm cutting diameter, a 32 mm shank for secure clamping and compatibility with CC-- 09T3 indexable inserts ensures consistent finishing and straightforward insert changes. Order the tool directly via Metav Werkzeuge or consult our specialists for integration advice. K117TM Boring Bar (S25T SCLCR) – 25 mm cutting diameter · 300 mm overall length · Teknik Makina The K117TM Boring Bar is a right‑hand, 95° internal turning tool engineered for use with CC-- 09T3 indexable inserts, offering stable performance in precision boring operations. *Boring bar type S25T SCLCR by Teknik Makina *25 mm cutting diameter, 300 mm overall length *Shank diameter 32 mm for solid clamping *Compatible with CC-- 09T3 indexable inserts Precision and stability for consistent internal turning The K117TM combines a defined 25 mm cutting diameter with a 32 mm shank and a 300 mm overall length to deliver reliable rigidity in constrained setups. The S25T SCLCR configuration positions the insert for controlled chip flow and reduced vibration, which supports repeatable component tolerances. For CNC machinists and toolroom specialists, the tool’s geometry reduces the need for corrective passes, enabling a more predictable production output and fewer scrapped parts. Geometry that cuts cycle times without compromising surface quality A 95° cutting angle and right‑hand cutting orientation create a balanced engagement between insert and workpiece. This geometry helps maintain a stable cutting edge contact and enhances machining efficiency during internal turning sequences. The use of indexable inserts allows rapid replacement when wear occurs, preserving setup accuracy and shortening downtime. The result is measurable time savings across serial production runs and an improved throughput for small to medium batches. Robust clamping and insert interchangeability Designed to accept CC-- 09T3 indexable inserts, the bar integrates with common insert families to simplify tool management. The klemmhalter 09 (clamp holder size 09) interface provides positive seating and a secure grip on the insert seat, ensuring consistent cutting height and repeatability after tool changes. Replaceable inserts eliminate regrinding and allow material‑specific grades to be selected, so tooling costs are controlled while surface finish and tool life can be optimised. Versatile use and straightforward workshop integration The tool’s S25T SCLCR ISO designation eases documentation and tool‑holder selection in tool libraries. At a weight of 1.165 kg and with standardised mounting dimensions, the bar fits common setups without elaborate fixturing. It is suitable for internal turning tasks where a rigid, indexable solution is required; the bar’s compatibility with established insert types streamlines procurement and spare‑part stocking, supporting efficient workshop logistics and consistent production scheduling. For tailored machining advice on the Teknik Makina K117TM boring bar, contact Metav Werkzeuge for personalised technical guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: K117TM Manufacturer: Teknik Makina ISO designation: S25T SCLCR Insert type: CC-- 09T3 Core data Cutting diameter: 25 mm Shank diameter: 32 mm Overall length: 300 mm Cutting height: 40 mm Weight: 1.165 kg Cutting angle: 95° Cutting direction: Right Design & features Compatible with CC-- 09T3 indexable inserts Shank for secure clamping Suited for internal turning operations SCLCR configuration for stable cutting FAQ Which inserts are compatible with this boring bar? The K117TM is specified for CC-- 09T3 indexable inserts; these replaceable inserts are fitted to the S25T SCLCR seat for secure engagement and straightforward exchange. What are the key dimensions to check for machine compatibility? Key dimensions include the 25 mm cutting diameter, 32 mm shank diameter and 300 mm overall length; these determine clearance, clamping and reach in the machining setup. Is the cutting direction right‑hand or left‑hand? The tool is a right‑hand cutting boring bar with a 95° cutting angle, suited to standard right‑hand internal turning operations. How does the tool support workshop efficiency? By using indexable inserts and a rigid shank design, the bar reduces downtime for regrinding, preserves setup accuracy after insert changes and supports faster cycle times in serial production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Schaftfräser von Teknik Makina für WNMX 09T3 Wendeplatten Der Schaftfräser ist ein robustes Zerspanungswerkzeug mit Innenkühlung, ausgelegt für Indexplatten des Typs WNMX 09T3 und präzise Bearbeitung in anspruchsvollen Fertigungsprozessen Innenkühlung für konstante Kühlung und längere Standzeit Kompatibel mit WNMX 09T3 Wendeplatten von Korloy Schaftdurchmesser 25 mm für stabile Werkzeugaufnahme Schnittlänge 60 mm für tiefe Eingriffe 2 Schneiden für ruhigen Lauf und hohe Oberflächengüte Die Kombination aus Wirtschaftlichkeit und Präzision macht den Schaftfräser zu einer zuverlässigen Wahl für Zerspanungsbetriebe; geeignet für WNMX 09T3 Wendeplatten von Korloy, unterstützt durch die integrierte Innenkühlung für verlängerte Standzeiten. Langlebigkeit durch Innenkühlung und durchdachte Konstruktion Die integrierte Innenkühlung führt das Kühlschmiermittel direkt zur Schnittzone und reduziert so thermische Belastungen an Schneidkante und Wendeplatte. Dadurch verbessert sich die Standzeit der Schneidplatten merklich und Stillstandzeiten wegen Werkzeugwechsel werden reduziert. Für Anwender, die auf konstante Prozessbedingungen Wert legen, sorgt diese Eigenschaft für planbare Produktionszyklen und geringere Werkzeugkosten. Präzise Schnittführung und ruhiger Lauf für bessere Oberflächen Mit 2 Schneiden und einer Schnittlänge von 60 mm liefert das Werkzeug gleichmäßige Spanbildung und reduzierte Vibrationen; das Ergebnis sind bessere Oberflächen und reproduzierbare Bauteilmaße. Der Schaftdurchmesser 25 mm gewährleistet eine stabile Spannaufnahme in gängigen Aufnahmevorrichtungen, wodurch die Prozesssicherheit bei hohen Schnittkräften steigt. Breites Einsatzspektrum und klare Kompatibilität Das Werkzeug ist speziell für Indexplatten des Formats WNMX 09T3 ausgelegt und passt zu Wendeplatten von Korloy, was den Einbau vorhandener Schneidplatten in bestehende Werkzeugkonzepte erleichtert. Für Anwender, die zwischen verschiedenen Plattenherstellern wählen, bietet diese Kompatibilität Planungssicherheit und Flexibilität beim Beschaffungsmanagement. Zur Erklärung: Wendeplatten sind austauschbare Schneidgeometrien, die eine wirtschaftliche Prozessführung ermöglichen. Montagehinweise, Schrauben und Handhabung Die Befestigung erfolgt mit einer Torx Schraube in der Größe M3x7, die mit einem Torx Schlüssel T8 angezogen wird; diese Kombination gewährleistet sicheren Sitz der Wendeplatte und einfache Wartung. Beim Wechseln der Platte empfiehlt sich kontrolliertes Anzugsmoment und Überprüfung der Sitzfläche, um Rundlauffehler zu vermeiden und die Lebensdauer von Platte und Werkzeug zu maximieren. Empfehlung: Den Schaftfräser von Teknik Makina über Metav Werkzeuge beziehen und bei Fragen die Fachberatung per eMail info@metav-werkezeuge.com oder telefonisch unter +49 2822 7131930 nutzen Produktmerkmale Artikelnummer: S802-1TM Marke: Teknik Makina Bezeichnung: Schaftfräser für WNMX 09T3 Wendeplatten Produktart: Schaftfräser Fakten Durchmesser: 25 mm Gesamtlänge: 150 mm Schaftdurchmesser: 25 mm Schaftlänge Schneide: 60 mm Schneiden: 2 Gewicht: 0.563 kg Besonderheiten Innenkühlung: ja (gezielte Kühlmittelzufuhr zur Schnittzone) Passend für Wendeplatten: WNMX 09T3 (Indexplatte Typ) Passend für Wendeplattenhersteller: Korloy Torx Schlüssel: T8 (Torx Schlüssel Größe) Torx Schraube: M3x7 (Schraubenabmessung) FAQ Für welche Wendeplatten ist der Schaftfräser geeignet? Der Schaftfräser ist ausgelegt für WNMX 09T3 Wendeplatten; die Konstruktion passt insbesondere zu Platten von Korloy, was eine einfache Integration in vorhandene Werkzeugkonzepte ermöglicht. Ist die Innenkühlung für Nassbetrieb geeignet? Ja, die integrierte Innenkühlung leitet Kühlschmierstoff direkt zur Schnittzone und unterstützt Nass- und mikroemulsionsbasierte Kühlkonzepte, um Hitzeentwicklung effektiv zu reduzieren. Welche Schraube und welcher Schlüssel werden für den Plattenwechsel benötigt? Verwendet wird eine Torx Schraube M3x7, die mit einem Torx Schlüssel T8 sicher angezogen wird; diese Kombination sorgt für sicheren Plattensitz und einfachen Service. Welche Vorteile bieten die 2 Schneiden? Die 2 Schneiden reduzieren Vibrationen und verbessern die Oberflächengüte bei kontinuierlicher Spanabfuhr, was besonders bei Serienfertigung zu gleichmäßigeren Ergebnissen führt. Wie lautet die Artikelnummer für Bestellungen und Ersatzteilabfragen? Die Artikelnummer lautet S802-1TM; diese Kennung erleichtert Bestellung, Lagerverwaltung und technische Rückfragen beim Vertrieb. Hersteller: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com / Verantwortlich: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The compact combination of a 25 mm diameter, internal coolant and compatibility with 3PKT 1004 indexable inserts ensures stable machining and reduced tool changes; order the screw-in cutter directly via Metav Werkzeuge or ask our consultants if needed. Screw-in cutter VT270TM – 25 mm with internal coolant (Teknik Makina) The screw-in cutter VT270TM is a compact milling head for 3PKT 1004 indexable inserts, designed for precise finishing and reliable coolant-through performance 25 mm diameter for compact milling Internal coolant for controlled cooling Compatible with Taegutec 3PKT 1004 inserts Three cutting edges for balanced cutting Consistent cutting performance in tight spaces The compact 25 mm diameter and a total length of 57 mm provide a space-saving solution that maintains dimensional accuracy in confined setups. With three cutting edges, the design delivers a balanced cut that reduces vibration and improves surface finish; this results in fewer reworks and more predictable cycle times. The lightweight construction (approx. 0.112 kg) reduces spindle load while preserving rigidity, which is beneficial for small machines and fixtures where stability directly affects throughput and part quality. Coolant-through system that extends tool life Integrated internal coolant channels feed lubricant directly to the cutting zone, lowering temperatures and improving chip evacuation. This cooling concept reduces thermal wear on the insert geometry and helps maintain a consistent cutting edge, which translates into longer intervals between indexings and lower consumable costs. For operations that prioritise reproducible results and lower overall tooling expenditure, the coolant-through configuration is a decisive technical advantage. Versatile compatibility and straightforward maintenance Designed for use with 3PKT 1004 indexable inserts (Taegutec-compatible), the tool head simplifies inventory management by supporting a commonly stocked insert family. The threaded connection (M12, thread height 35 mm) and the Torx clamping screw specification (Torx key T8, screw M2.5x7) enable quick insert changes and secure fixation. These features minimise downtime during tool changes and allow maintenance personnel to swap inserts with standard workshop tools, supporting efficient shift schedules and predictable production planning. Technical reliability and workshop integration The head is engineered for repeatable seating and alignment in standard screw-in holders, making it suitable for a broad range of milling tasks that require compact tooling with reliable coolant supply. The 22 mm effective cutting height provides sufficient engagement for finishing passes and light roughing, while the three-edge geometry balances feed rates and surface outcome. As part of a coherent tooling strategy, this milling head supports process stability and measurable productivity gains on small-to-medium batch runs. For precise compact milling with coolant-through benefits, contact Metav Werkzeuge to discuss the VT270TM from Teknik Makina and to arrange purchase or tailored technical advice by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: VT270TM Manufacturer: Teknik Makina Diameter: 25 mm Overall length: 57 mm Thread: M12 Thread height: 35 mm Cutting height: 22 mm Number of cutting edges: 3 Weight: 0.112 kg Internal coolant: yes Compatible inserts: 3PKT 1004 (Taegutec) Torx key: T8 Torx screw: M2.5x7 Product type: screw-in cutter FAQ What insert type fits this cutter? The cutter accepts 3PKT 1004 indexable inserts, compatible with Taegutec insert families for straightforward sourcing. Does the tool support coolant-through operation? Yes, the VT270TM features internal coolant channels to deliver coolant directly to the cutting zone. What is the thread connection for mounting the head? The head uses an M12 screw-in connection with a thread height of 35 mm for secure mounting. How many cutting edges does the head have and what are the benefits? The head is equipped with three cutting edges, which balance cutting forces, reduce vibration, and improve surface finish during finishing operations. Which fastening hardware is required for insert clamping? Insert clamping uses a Torx screw M2.5x7 tightened with a T8 Torx key for reliable and repeatable fastening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise mounting, internal coolant and proven insert compatibility to streamline milling operations. Benefit from robust serviceability and consistent chip control for reduced downtime — order or request advice via Metav Werkzeuge for a reliable supply and fast technical guidance. Screw-in milling cutter VT160-1TM — 25 mm diameter, internal coolant, Teknik Makina The Screw-in milling cutter VT160-1TM is a compact, serviceable cutter designed for machining with AP--1604 indexable inserts in industrial and trade workshops. 25 mm cutting diameter Internal coolant for reliable chip removal Compatible with AP--1604 indexable inserts M12 screw-in thread for secure mounting Precision and predictable performance for indexable-insert milling The compact tool is engineered for stable, repeatable results when fitted with AP--1604 inserts. With a 25 mm diameter and two cutting edges, the design focuses on efficient metal removal with predictable cutting forces. The internal coolant channel ensures consistent coolant delivery to the cutting zone, improving tool life and helping to avoid built-up edge. This stability leads to fewer interruptions and a more economical machining cycle when compared with ad hoc tooling solutions. Robust mounting and easy insert servicing to reduce downtime A secure M12 screw-in connection and defined thread height support fast, vibration-resistant clamping on the toolholder. Replaceable components are accessed using the supplied Torx T15 key and M4x10 Torx screws for straightforward insert changes and maintenance. The combination of standardised fastenings and a compact head reduces changeover time, which benefits production runs where quick tool swaps preserve spindle utilisation and consistency. Compact dimensions that simplify setup and handling At an overall length of 55 mm and a cutting height of 33 mm, the tool offers a low-protrusion solution for confined setups and shoulder milling. The modest mass (approx. 0.107 kg) contributes to reduced centrifugal loads in high-speed applications and makes balancing easier on compact toolholders. These attributes translate into improved surface quality and less fixture rework, supporting a leaner workflow on the shopfloor. Compatibility and supply chain reliability for industrial users Designed to accept AP--1604 inserts from major suppliers such as Korloy, the cutter integrates into established tooling systems without the need for bespoke adapters. Supplied by Teknik Makina and distributed through Metav Werkzeuge, the product benefits from a European fulfilment network that prioritises consistent availability and a clear quality filter at the Emmerich location. The result is straightforward purchasing, dependable delivery and the assurance of compatible spare parts when required. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina screw-in milling cutter VT160-1TM into existing machining setups and to secure available stock; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: VT160-1TM Brand: Teknik Makina Label: 25mm Einschraubfräser AP-- 1604 L55mm mit Innenkühlung Facts Diameter: 25 mm Overall length: 55 mm Thread: M12 Thread height: 22 mm Cutting edges: 2 Cutting height: 33 mm Weight: 0.107 kg Special features Internal coolant: Yes Compatible inserts: AP--1604 Compatible insert manufacturer: Korloy Torx key: T15 Torx screw: M4x10 FAQ Which inserts fit this cutter? The cutter accepts AP--1604 indexable inserts; compatible inserts from Korloy are suitable for use with this Teknik Makina screw-in milling cutter (VT160-1TM). Is the tool supplied with a coolant channel? Yes — the tool features internal coolant, providing direct coolant delivery to the cutting edge to assist chip evacuation and tool life. What fastening is required for mounting? Mounting uses an M12 screw-in thread with a defined thread height; insert clamping employs an M4x10 Torx screw tightened with a T15 Torx key. How many cutting edges does the head provide? The head is configured with two cutting edges, offering a balance between material removal rate and surface finish for general milling tasks. What is the overall length and handling benefit? Overall length is 55 mm, which reduces tool projection and simplifies setups in constrained workspaces while aiding dynamic stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-performance milling head that combines 25 mm cutting diameter with internal coolant and a secure M12 screw-in interface for reliable insert clamping; order the tool directly via Metav Werkzeuge or consult the team for application advice. Screw-in cutter for APXT 1003 indexable inserts — 25 mm, internal coolant (Teknik Makina) The Screw-in cutter for APXT 1003 indexable inserts is a compact milling head designed for insert-based roughing and finishing operations, offering internal coolant delivery and a robust M12 threaded connection for secure mounting in modular toolholders. 25 mm diameter for versatile milling Internal coolant for improved chip evacuation M12 screw-in thread with 22 mm engagement Compatible with APXT 1003 Korloy inserts Stable cutting with consistent accuracy The compact milling head delivers high stability through its 25 mm diameter and a solid screw-in interface. The combination of a M12 thread with 22 mm engagement ensures reliable seat and repeatable run-out values, which supports consistent part quality across batches. With three cutting edges and a total length of 55 mm, the tool balances rigidity and reach for many modular setups. These features reduce vibration and help to maintain tolerances in serial production, increasing overall process reliability. Improved tool life thanks to coolant and chip control Integrated internal coolant channels feed lubrication directly to the insert zone, lowering cutting temperatures and improving flank wear behaviour. Direct coolant supply also supports efficient chip evacuation, especially in interrupted cuts or when machining materials prone to built-up edge. The result is extended insert life and fewer tool changes, which contributes to lower downtime and a more economical process in mixed-production environments. Fast insert replacement and secure clamping The head is designed for quick serviceability: inserts are fixed with a Torx T8 clamping screw (M2.5×5.5), enabling precise, repeatable torque settings and a secure fit. Compatibility with APXT 1003 type indexable inserts from Korloy gives access to a broad range of grades for different materials and cutting conditions. The simple clamping system reduces handling time during maintenance and supports predictable tool-change routines on the shop floor. Suited for flexible workshops and industrial lines This screw-in milling head is suited to workshops and production lines that require a compact, modular solution for insert-based milling. Its balanced design and internal coolant capability make it a pragmatic choice for operations requiring both roughing capacity and the option for higher-quality finishes. Lightweight at 0.135 kg, the head integrates easily into automated tool changers and small machining centres, helping to streamline tooling inventories while preserving machining performance. Contact Metav Werkzeuge for tailored recommendations on Teknik Makina screw-in cutters with internal coolant and ensure the right combination of inserts and toolholders for the application Technical Data Article number: VT140-1TM Label: 25mm Einschraubfräser APXT 1003 L55mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 25 mm Total length: 55 mm Weight: 0.135 kg Thread: M12 Thread engagement height: 22 mm Number of cutting edges: 3 Cutting-edge height: 33 mm SKU: VT140-1TM eCl@ss: 21180806 Special features Internal coolant Compatible with APXT 1003 indexable inserts Torx key: T8 Torx screw: M2.5×5.5 Label indicates Korloy compatibility FAQ What insert type is required for this milling head? The head accepts APXT 1003 indexable inserts; compatibility is stated for Korloy grades suitable for the intended cut. Is the coolant internal or external on this tool? The milling head features internal coolant that supplies lubricant directly to the cutting zone. What thread is used to mount the cutter? The tool uses an M12 screw-in thread with 22 mm engagement for secure mounting. How many cutting edges does the head have and what is their height? The head is equipped with three cutting edges and a cutting-edge height of 33 mm. Which torx key and screw type are used for insert clamping? Insert clamping is by Torx T8 using an M2.5×5.5 screw. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a compact 25 mm diameter, secure M12 screw‑in mounting and coolant‑through capability for uninterrupted machining. The result is dependable indexable‑insert milling with reduced changeover time — order via Metav Werkzeuge or request technical advice from the consultants. VT192-1TM 25 mm screw-in cutter for BLMP 0603 with internal coolant – Teknik Makina A screw-in cutter designed for BLMP 0603 indexable inserts, offering compact head dimensions and coolant‑through performance for efficient milling in confined set-ups 25 mm diameter for compact milling heads Internal coolant channel for improved chip evacuation M12 screw-in thread, 22 mm thread height Compatible with BLMP 0603 inserts (Taegutec) Precision and compatibility for consistent production The VT192-1TM is built around a compact 25 mm diameter to keep overhang low and rigidity high, a decisive factor in reducing vibration and improving surface finish. With four cutting edges configured for indexable inserts, the tool enables economical insert rotation and rapid re‑establishment of cutting parameters after a wear change. Compatibility with BLMP 0603 indexable inserts — including Taegutec grades — provides flexibility in selecting carbide grades for specific materials and cutting conditions, making the head suitable for job shops and production environments that demand repeatable results and predictable tool life. Cooler chips and longer insert life from coolant‑through design A coolant‑through arrangement provides targeted cooling at the cutting zone and supports active chip evacuation, which lowers cutting temperatures and minimises built‑up edge formation. The internal coolant channel not only extends insert life but also reduces the frequency of regrinds and replacements, contributing to lower total machining costs and higher uptime. For applications where thermal control and swarf management are critical, the coolant‑through option improves process stability and helps maintain tight dimensional tolerances over longer cycles. Secure mounting and workshop efficiency for fast tool changes Designed for simple, repeatable mounting, the head uses an M12 thread with a 22 mm seating height for reliable screw‑in retention and precise concentricity. Fast reassembly is supported by the Torx screw specification (Torx T8 with screw M3x6.2), ensuring quick insert clamping and minimal downtime. At just 0.119 kg, the assembly keeps spindle load light while remaining robust enough for standard milling operations. This combination of secure mounting, lightweight construction and CNC‑ready compatibility makes the head a practical choice for manufacturers seeking fast tool swaps and consistent production throughput. For specification support or to source Teknik Makina’s VT192-1TM screw-in cutter, contact Metav Werkzeuge in Emmerich for expert guidance and prompt delivery: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: VT192-1TM Manufacturer: Teknik Makina Product type: screw-in cutter Model / inserts: for BLMP 0603 indexable inserts SKU: VT192-1TM Specifications Diameter: 25 mm Overall length: 57 mm Thread height: 22 mm Thread: M12 Number of cutting edges: 4 Cutting height: 35 mm Weight: 0.119 kg Materials & Features Internal coolant: yes Compatible inserts: BLMP 0603 (Taegutec) Torx screw: M3x6.2 Torx key: T8 Intended use: indexable-insert milling FAQ What inserts are compatible with this screw-in cutter? The cutter accepts BLMP 0603 indexable inserts; Taegutec grades are compatible and commonly used with VT192-1TM to suit different materials and machining tasks. Does the tool support coolant-through machining? Yes, internal coolant is provided to deliver coolant directly to the cutting zone, improving chip evacuation and helping to prolong insert life. How is the tool mounted and secured? Mounting is via an M12 screw‑in thread with a 22 mm thread height; insert clamping uses a Torx screw (T8) sized M3x6.2 for secure, repeatable assembly. Which workshop environments benefit most from this head? The compact diameter, four cutting edges and coolant‑through capability make the head suitable for job shops and production lines requiring low overhang, quick insert changes and stable cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise screw-in mounting, compact dimensions and straightforward insert compatibility to keep machining cycles consistent and maintenance quick; order the cutter directly via Metav Werkzeuge or consult our specialists for application guidance. Screw-in Milling Cutter VT192TM — for BLMP 0603 indexable inserts, M12 thread A compact screw-in milling cutter Screw-in Milling Cutter VT192TM designed for secure mounting with BLMP 0603 indexable inserts and routine CNC milling applications. M12 threaded shank, quick mounting 25 mm cutting diameter for versatile use Two cutting edges for efficient material removal Compatible with BLMP 0603 indexable inserts Reduced downtime through fast, reliable mounting The screw-in design with an M12 thread and a dedicated M3x6.5 screw secured with a T8 Torx key delivers a consistently rigid connection that shortens tool-change intervals. By combining a compact threaded arbor with a standardised fixing method, the system reduces clamping variability and therefore minimizes setup time. This mechanical stability translates into fewer interruptions on the production floor and a predictable machining rhythm — a clear advantage for shops focused on throughput and repeatability. Consistent cutting performance with balanced geometry Equipped for BLMP 0603 indexable inserts from Taegutec, the cutter benefits from a 100° cutting angle and two cutting edges that produce balanced radial forces and stable chip formation. The geometry supports steady cutting action and helps to prevent chatter during interrupted cuts. For operations requiring repeatable slotting or light face-milling, this combination provides a reliable, economical option that converts insert life into predictable productivity gains. Compact dimensions for tight setups and accurate placement The tool’s modest footprint — 25 mm diameter, 57 mm overall length and 25 mm cutting height — enables use in restricted tool pockets and close-quarter fixtures without compromising stiffness. The 22 mm thread height ensures sufficient engagement in the holder while the low mass (0.044 kg) reduces centrifugal loads at moderate spindle speeds. These measurable characteristics make the cutter suitable where tool clearance and positional accuracy are priorities, helping to maintain part tolerances across series runs. Low-maintenance routine and seamless integration into workflows As a purpose-built screw-in cutter from Teknik Makina, the VT192TM simplifies insert changes and routine checks: the standard Torx fixing avoids special tools, and the indexable design means quicker refresh cycles compared with brazed or solid tips. The tool integrates directly with established insert formats, helping workshops maintain consistent tool lists and reducing inventory complexity. The straightforward mechanical design supports predictable service intervals and keeps maintenance tasks brief and unambiguous. Contact Metav Werkzeuge for tailored application advice and rapid supply of Teknik Makina screw-in cutters from Emmerich—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VT192TM Manufacturer: Teknik Makina Diameter: 25 mm Overall length: 57 mm Cutting height: 25 mm Thread height: 22 mm Weight: 0.044 kg Cutting angle: 100° Number of cutting edges: 2 Thread: M12 Compatible inserts: BLMP 0603 Compatible insert manufacturer: Taegutec Fixing screw: M3x6.5 Torx key size: T8 FAQ What insert type fits this cutter? The screw-in milling cutter VT192TM is designed for BLMP 0603 indexable inserts and is compatible with inserts from Taegutec. Which thread and fixing are used for mounting? Mounting is via an M12 thread; the insert clamping is secured with an M3x6.5 Torx screw (T8) as specified for the VT192TM. How many cutting edges does the tool provide and why does that matter? The cutter has two cutting edges, which gives balanced cutting forces and efficient chip removal for stable machining and predictable insert wear. Is the tool suitable for compact toolholders and tight setups? Yes — the 25 mm diameter and 57 mm overall length make the VT192TM appropriate for constrained fixturing while maintaining stiffness. What measurable dimensions are important for setup checks? Key values to confirm are 25 mm diameter, 25 mm cutting height, 22 mm thread height and overall length 57 mm for accurate tool offsets and holder compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, compact dimensions and secure Torx fastening for uninterrupted milling cycles; order the cutter through Metav Werkzeuge or consult our experts for application-specific recommendations. 25 mm screw-in milling cutter VT265TM — compatible with BLMP 0904 indexable inserts, 3 cutting edges | Teknik Makina The 25 mm screw-in milling cutter for BLMP 0904 indexable inserts offers a compact, insert-based solution for face and shoulder milling operations in CNC machining, designed for reliable repeatability in production settings. 25 mm diameter for tight pockets Three cutting edges for smooth chip control Compatible with Taegutec BLMP 0904 inserts Secure Torx fixing with T10 and M3.5x8.5 screw High productivity through precise insert integration The cutter head is engineered to combine indexable insert technology with a compact mounting form, supporting stable cutting performance in serial machining. With a 25 mm diameter and three cutting edges, the tool balances material removal rate and surface quality, enabling shorter cycle times without sacrificing finish. The insert interface is specified for BLMP 0904 inserts, which simplifies inventory and reduces changeover time when paired with compatible brands such as Taegutec. The result is a dependable solution for repetitive milling tasks where process stability matters. Fast, secure clamping for minimal downtime The design features a screw-in mounting system with a defined thread height of 20 mm and a robust fixing method that uses a T10 Torx key and M3.5x8.5 Torx screw to hold the insert securely. This arrangement ensures consistent seating and repeatable geometry after each change, lowering the risk of misalignment and rework. The compact 55 mm overall length reduces overhang, improving rigidity, while the precise fastening arrangement permits quick insert replacement and controlled torque application during maintenance. Compact dimensions that support flexible toolpaths A short tool projection and modest weight (approx. 0.114 kg) contribute to reduced vibration and improved run-out characteristics on high-speed mills. The cutter’s geometry with a 35 mm cutting height delivers enough engagement for light to moderate-DOC (depth of cut) passes while keeping cutter mass low. In practice, this enables tighter tool spacing in multi-tool setups and better accessibility in confined workpiece features, benefiting workshops aiming to increase machine utilisation and throughput. Procurement confidence and workshop support Sourcing this screw-in cutter through an experienced distributor adds tangible benefits: inventory alignment with insert families, documented technical data and straightforward logistics. The modular nature of the insert system reduces tooling complexity and supports predictable reconditioning cycles. Metav’s role as a precision partner means orders are supported from stock in Emmerich, backed by a broad product range and customer-proven reliability, which helps maintain production continuity and supplier consolidation. For procurement enquiries or detailed application advice on the Teknik Makina VT265TM screw-in milling cutter, contact Metav Werkzeuge for tailored recommendations and fast delivery from Emmerich. Technical data SKU: VT265TM Manufacturer: Teknik Makina Product label: 25mm screw-in milling cutter BLMP 0904 L55mm Product type: screw-in milling cutter Core specifications Diameter: 25 mm Overall length: 55 mm Cutting height: 35 mm Thread height: 20 mm Thread: 12 Cutting edges: 3 Weight: 0.114 kg Torx key: T10 Torx screw: M3.5x8.5 Compatibility & special features For BLMP 0904 indexable inserts Compatible with Taegutec inserts Insert fastening with Torx screw Screw-in mounting FAQ What inserts does this cutter accept? The cutter accepts BLMP 0904 indexable inserts; it is supplied to fit that insert family and is compatible with inserts from Taegutec. Which tool is used to tighten the insert screw? Insert fastening requires a T10 Torx key and the specified M3.5x8.5 Torx screw for secure clamping. What are the key dimensions to check for machine setup? Key dimensions include the 25 mm diameter, 55 mm overall length and 20 mm thread height, which are relevant for toolholder clearance and programme offsets. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust M12 screw-in connection, a precise 93° cutting angle and compatibility with EPMT 0603 indexable inserts for stable, repeatable milling. Take advantage of secure Torx clamping and compact dimensions to streamline tool changes; order the cutter directly via Metav Werkzeuge or consult their specialists for technical advice. Screw-in cutter VT232TM – M12 thread, Ø25 mm (Teknik Makina) A Screw-in cutter VT232TM engineered for industrial milling with EPMT 0603 indexable inserts, offering secure screw-in mounting and consistent chip control in production environments M12 threaded connection for secure clamping Compatible with EPMT 0603 indexable inserts Four cutting edges for balanced material removal Torx M2.5x5.5 clamping screw with T7 key Secure mounting reduces setup time and runout risk The screw-in design with a M12 threaded connection provides a compact, repeatable interface that lowers setup time and minimises radial runout. Combined with the Torx M2.5x5.5 clamping screw and the T7 drive, the clamping system secures the insert reliably, which reduces vibration and helps maintain dimensional consistency across batches. For workshops that prioritise dependable tool seating and quick indexability, this arrangement supports uninterrupted production and predictable cycle times. Stable cutting geometry for uniform chip formation With a cutting diameter of Ø25 mm, a 93° cutting angle and 4 cutting edges, this tool delivers balanced axial and radial engagement. The cutter’s cutting height 20 mm and overall length 55 mm are optimised for short overhangs and improved stiffness; the thread length 35 mm ensures secure fixation in the holder. The model VT232TM is therefore suited to operations where repeatable chip control and moderate material removal are required, translating technical geometry into longer insert life and fewer re‑settings on the shop floor. Practical compatibility and workshop handling Designed for use with EPMT 0603 indexable inserts and compatible with Hitachi insert geometries, the screw-in cutter simplifies inventory management by pairing with widely used insert types. At just 0.11 kg, the tool is easy to handle during tool changes and packing. The combination of standardised fixing, common insert sizing and a compact form factor makes the cutter a practical choice for maintenance-focused production lines and specialist job shops that require quick interchangeability without compromising stability. Choose the Teknik Cutting Tools screw-in cutter VT232TM for secure, repeatable milling; contact Metav Werkzeuge in Emmerich for procurement guidance and technical consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VT232TM Manufacturer: Teknik Makina Product: Screw-in cutter for indexable inserts Compatible inserts: EPMT 0603 (for EPMT 0603 Indexable Inserts) Compatible insert manufacturer: Hitachi ECLASS: 21180806 ETIM: EC011860 Facts Diameter: 25 mm Thread: M12 Overall length: 55 mm Thread length / height: 35 mm Cutting height: 20 mm Cutting edges: 4 Cutting angle: 93° Weight: 0.11 kg Torx screw: M2,5x5,5 Torx key: T7 Special features Screw-in cutter design For EPMT 0603 indexable inserts Compatible with Hitachi inserts Compact, short-overhang geometry FAQ Which inserts fit this cutter? The VT232TM is intended for EPMT 0603 indexable inserts; it is also compatible with matching Hitachi insert variants specified for EPMT 0603. What is the required clamping screw and key? Clamping is secured with a M2.5x5.5 Torx screw and the appropriate drive is T7, ensuring repeatable torque and secure seating. What are the main dimensions to check for holder compatibility? Key dimensions are Ø25 mm diameter, M12 thread and an overall length of 55 mm; these determine holder fit and permissible overhang. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a compact screw-in design, internal coolant and proven indexable insert compatibility to maintain stable cycle times and reduce tool changes. Order supply and technical advice for the Teknik Makina VT232-1TM via Metav Werkzeuge or consult our specialists for application support. Screw-in cutter VT232-1TM – 25 mm, internal coolant (for EPMT 0603 indexable inserts) by Teknik Makina Screw-in cutter VT232-1TM is a coolant-fed milling head engineered for use with EPMT 0603 indexable inserts, offering a compact solution for precision milling operations. 25 mm cutting diameter Internal coolant supply M12 screw-in thread 4 cutting edges, 20 mm insert height Faster, more consistent material removal with a compact head The combination of a 25 mm diameter and 4 cutting edges delivers an efficient balance of metal removal rate and surface quality. Multiple cutting edges distribute the cutting forces, which reduces vibration and makes the machining process more predictable; this stability is reflected in shorter cycle times and fewer reworks. The head geometry and insert seating are designed for secure clamping, so indexable inserts remain stable during interrupted cuts and higher feed rates. Measurable performance gains can be achieved simply by matching the correct insert grade and cutting data. Straightforward fitment and proven insert compatibility Installation is simplified by the M12 thread and the compact dimensions of the head, while retention is via a standard Torx T8 key and M2.5×5.5 screw, allowing quick insert changes and tight clamping. The head accepts EPMT 0603 indexable inserts and is compatible with Hitachi insert variants, so existing tool inventories can be leveraged. Indexable inserts permit rapid replacement without regrinding; this modular approach means downtime is reduced because the cutting edge, not the whole tool, is replaced. Controlled cooling for longer tool life and consistent cuts An integrated internal coolant channel directs lubricant precisely to the cutting zone, improving chip evacuation and reducing thermal load on the insert. This targeted cooling helps to slow flank wear and maintain cutting-edge geometry for longer, which in turn supports extended tool life and more consistent dimensional results across batches. The internal coolant also lowers the risk of built-up edge formation and makes high-feed or semi-finishing operations more reliable. Compact, workshop-friendly design that integrates easily With a 55 mm overall length, a thread height of 35 mm and a mass of 0.11 kg, the head is engineered for compact tool magazines and reduced spindle overhang. The 20 mm insert height offers substantial cutting engagement while keeping the assembly balanced, helping to protect spindle bearings and minimise run-out-related errors. The small footprint and standard screw-in interface make the cutter suitable for both series production and smaller workshop environments where space and quick changeovers matter. For coolant-fed performance and reliable insert handling, contact Metav Werkzeuge to discuss supply and application advice for the Teknik Makina VT232-1TM screw-in cutter and to arrange prompt delivery from Emmerich. Technical data SKU: VT232-1TM UID: VT232-1TM Manufacturer: Teknik Makina Product type: Screw-in cutter Description: 25 mm screw-in cutter for EPMT 0603 indexable inserts with internal coolant Label: 25mm Einschraubfräser EPMT 0603 L55mm mit Innenkühlung Core data Diameter: 25 mm Overall length: 55 mm Thread height: 35 mm Thread: M12 Weight: 0.11 kg Cutting edges: 4 Insert height: 20 mm ECLASS: 21180806 Special features Internal coolant For insert type: EPMT 0603 Compatible insert manufacturer: Hitachi Torx key: T8 Torx screw: M2.5×5.5 FAQ Which inserts fit this screw-in cutter? The VT232-1TM accepts EPMT 0603 indexable inserts and is specified to be compatible with Hitachi insert variants for straightforward replacement. How is the cutter secured to the spindle or holder? The head uses an M12 screw-in thread for installation and a Torx T8 screw (M2.5×5.5) for insert clamping on the VT232-1TM. Does the cutter provide coolant directly to the cutting zone? Yes, the VT232-1TM features internal coolant routing to the cutting edge to improve chip evacuation and thermal control. Can the head be used for high-feed finishing operations? With 4 cutting edges and a robust insert seat, the head is designed to handle elevated feeds when the correct insert grade and cutting data are selected for the task. What maintenance is required for the screw-in cutter? Routine checks of the clamping screw torque and inspection of insert seats are recommended; replacing worn inserts on the VT232-1TM preserves cutting performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from efficient material removal with internal coolant and a secure M12 screw-in connection for steady production performance; the compact design and compatibility with LNMU 0303 indexable inserts reduce tooling changes and downtime — order the cutter directly via Metav Werkzeuge or ask our consultants for tailored advice. 25 mm screw-in milling cutter VT304-1TM — for LNMU 0303 indexable inserts with internal coolant (Teknik Makina) The 25 mm screw-in milling cutter VT304-1TM is engineered for high-efficiency milling with LNMU 0303 indexable inserts, offering a compact, coolant-fed solution for general and semi‑finishing operations. 25 mm diameter with internal coolant Compatible with LNMU 0303 indexable inserts M12 screw-in connection, 22 mm thread height Four cutting edges, 57 mm overall length Enhanced metal removal and consistent cycle times The compact head with a 25 mm diameter and four cutting edges is designed to deliver a secure balance between material removal rate and surface quality. Internal coolant channels feed cutting edges directly, substantially reducing heat at the cutting zone and extending insert life. The screw-in design with an M12 interface and 22 mm thread height provides rigid mounting, which lowers vibration and improves dimensional stability during high-feed passes. These technical attributes translate into measurable production benefits: fewer tool changes, longer insert life and more predictable cycle times. Proven compatibility for flexible tooling strategies Compatibility with LNMU 0303 indexable inserts from Tungaloy simplifies stocking and replacement procedures. The cutter accepts standard indexable inserts, secured with an M2.5x7 Torx screw operated by a Torx T8 key, enabling rapid insert changes and minimal setup time. Internal coolant support complements coated insert grades by preserving cutting-edge microgeometry under thermal load. This modular approach allows a single holder to serve multiple work steps, reducing inventory complexity while maintaining process reliability. Compact design that supports workshop efficiency With an overall length of 57 mm and a lightweight construction of 0.108 kg, the tool is easy to handle and well suited for compact toolholders where space is limited. The screw-in connection simplifies installation and removal, aiding quick reconfiguration of tool magazines. The cutter’s geometry and coolant feed are engineered to support both roughing and finishing strategies, offering a versatile option for mixed-production environments. Clear technical attributes allow straightforward integration into CAM setups and predictable tooling lists for procurement. For supply, technical details or ordering through Metav Werkzeuge — trusted in precision and delivery from Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the VT304-1TM screw-in milling cutter and compatible insert options Technical Data Article number: VT304-1TM Manufacturer: Teknik Makina Product type: screw-in milling cutter Designation: 25mm screw-in cutter for LNMU 0303 indexable inserts Facts Diameter: 25 mm Overall length: 57 mm Weight: 0.108 kg Thread height: 22 mm Number of cutting edges: 4 Cutting-edge height: 35 mm Special features Internal coolant Compatible inserts: LNMU 0303 Compatible insert manufacturer: Tungaloy Thread: M12 Torx key: T8 Torx screw: M2.5x7 FAQ Which insert type is required for this cutter? The cutter uses LNMU 0303 indexable inserts; Tungaloy-specified grades are directly compatible with the VT304-1TM screw-in milling cutter. Is internal coolant supplied through the tool? Yes, the VT304-1TM is equipped with internal coolant channels to feed coolant directly to the cutting edges and improve tool life. What is the mounting interface for the cutter? Mounting is via an M12 screw-in connection with a thread height of 22 mm, providing rigid clamping in the toolholder. How many cutting edges are available and what is the overall length? The cutter has four cutting edges and an overall length of 57 mm, offering a compact but robust option for mixed milling tasks. Which Torx key and screw are used to secure the inserts? Inserts are fastened with an M2.5x7 Torx screw tightened using a Torx T8 key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of secure screw-in clamping, a compact 25 mm diameter and compatibility with LOGU 0303 indexable inserts for reliable, repeatable milling cycles. Order the cutter directly via Metav Werkzeuge or consult the Metav team for technical matching and supply. Screw-in milling cutter VT314TM — 25 mm, M12 thread (Teknik Makina) Screw-in milling cutter for LOGU 0303 indexable inserts, designed for compact, high-repeatability milling operations in production and workshop environments. Secure screw-in clamping M12 25 mm diameter for versatile face milling Compatible with LOGU 0303 indexable inserts Four cutting edges with 35 mm cutting height Stable clamping for consistent production results The screw-in system with an M12 thread provides a rigid connection between toolholder and cutter head, reducing vibration and improving surface finish. A secure interface translates directly into fewer reworks and higher first-pass yields, making the tool a practical choice where repeatability matters. Thread engagement of 22 mm ensures reliable axial support during interrupted cuts, while the compact overall length of 57 mm helps maintain spindle stability on shorter overhangs. Efficient cutting geometry that boosts throughput With a 25 mm diameter and four cutting edges, the cutter is optimised for steady material removal and balanced load distribution across inserts. The 35 mm cutting height permits deeper engagement per pass where process parameters allow, reducing the number of passes required. Using LOGU 0303 indexable inserts simplifies edge replacement: worn inserts are changed quickly without regrinding, so the production line resumes operation with minimal downtime. The light mass of 0.097 kg contributes to lower inertial stress on the spindle during acceleration and deceleration phases. Simple serviceability and reduced downtime Insert retention uses a Torx fastener system (Torx T8 key, screw M3x7) that is common in workshop settings and easy to source. This standardised fastening reduces service time and tool-change errors compared with proprietary systems. The combination of indexable inserts and standardised fixing also lowers tooling inventory costs: replacement inserts are compact and economical to keep in stock compared with complete single-piece cutters. Designed for integration into existing machining cells Compatibility with Kyocera inserts means the cutter fits established insert families, enabling process engineers to choose grades tuned to specific alloys and cutting conditions. The tool's balanced dimensions and modest weight make it suitable for both manual tool changes and automated tool magazines. For buyers seeking dependable supply and technical guidance, Metav Werkzeuge provides a focused distribution channel that combines comprehensive product availability with technical consultation to align tool selection with production goals. Request technical matching or a supply consultation from Metav Werkzeuge to secure the Teknik Makina screw-in milling cutter VT314TM for LOGU 0303 inserts and ensure seamless integration into existing workflows Technical Data SKU: VT314TM Label: 25mm Einschraubfräser LOGU 0303 L57mm Manufacturer: Teknik Makina Product type: Screw-in milling cutter UID: VT314TM Core specifications Diameter: 25 mm Overall length: 57 mm Thread: M12 Thread engagement height: 22 mm Cutting edges: 4 Cutting height: 35 mm Weight: 0.097 kg Special features For LOGU 0303 indexable inserts Compatible with Kyocera inserts Torx key T8 required Torx screw M3x7 for insert retention FAQ Which inserts fit this cutter? The cutter accepts LOGU 0303 indexable inserts; compatible Kyocera grades are commonly used for a range of materials. What is the thread size and engagement? The tool uses an M12 screw-in interface with 22 mm thread engagement for secure clamping. How many cutting edges does the cutter have? This model is fitted with four cutting edges, enabling balanced cutting and even wear distribution. What are the key dimensions to check for toolholder compatibility? Check the 25 mm diameter and 57 mm overall length to ensure adequate clearance and spindle overhang. Is the fastening system workshop-friendly? Yes. Insert fixation uses a Torx T8 key and M3x7 screw for quick, standardised serviceability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, reliable tool that combines a 25 mm cutting diameter, internal coolant and a secure M12 screw‑in connection to keep small‑diameter milling operations consistent and productive; order the cutter directly via Metav Werkzeuge or contact our consultants for application advice. Screw-in milling cutter VT314-1TM for LOGU 0303 indexable inserts — 25 mm, internal coolant, Teknik Makina The screw-in milling cutter VT314-1TM is a compact, modular tool intended for CNC milling operations that accept LOGU 0303 indexable inserts, providing a balance of rigidity and accessibility for close‑tolerance machining in workshops and production lines. 25 mm diameter for compact milling Internal coolant for improved chip evacuation M12 screw-in connection for secure mounting Compatible with LOGU 0303 Kyocera inserts Greater productivity from a compact diameter and multiple cutting edges A small cutter with a 25 mm diameter offers access to confined features without sacrificing stability. The tool’s four cutting edges help to spread wear and extend effective machining time between indexings, increasing throughput for serial production or batch work. Using LOGU 0303 indexable inserts simplifies maintenance: worn inserts are replaced quickly, avoiding lengthy regrinds and keeping machine uptime high. The overall length of 57 mm supports a favourable stiffness‑to‑reach ratio, which reduces chatter and helps maintain consistent surface quality when tackling peripheral or slotting operations. Controlled cooling and cleaner chip flow for longer tool life The built‑in internal coolant directs cutting fluid towards the insert seat and cutting zone to improve lubrication and chip evacuation. This focused coolant supply reduces heat at the cutting edge and assists swarf removal from narrow slots, which contributes to a better surface finish and reduces thermal wear on the insert. For operations where coolant access is restricted, the internal delivery ensures that the cooling effect reaches the active cutting zone rather than being deflected externally, helping to preserve insert life and part quality. Secure mechanical connection and straightforward serviceability The screw‑in design features an M12 thread with a thread height of 22 mm, ensuring a robust, concentric connection to the tool holder and dependable repeatability during tool changes. The cutter is supplied with a Torx fastening system using a T8 key and an M3x7 Torx screw for insert clamping, which allows safe, rapid insert replacement with common workshop tools. With a cutting height of 35 mm and a nominal weight of 0.097 kg, the assembly is light enough for fast tool changes yet engineered to maintain positional accuracy under typical machining loads. Practical applications and compatibility in production environments Designed for indexable insert milling, the cutter accepts LOGU 0303 inserts and is specified for use with inserts from Kyocera, making it suitable for a variety of milling tasks where small diameters are required, such as finishing pockets, narrow slots and edge milling. The modular nature of the tool allows integration into existing tool systems and straightforward stockkeeping for maintenance teams. For workshops seeking predictable performance and easy insert logistics, this cutter supports efficient changeovers and consistent part quality across production runs. For tailored advice on integrating the VT314-1TM into existing workflows or to request a formal quote from Metav Werkzeuge — including guidance on suitable LOGU 0303 Kyocera inserts — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930; Metav Werkzeuge can advise on availability and shipping from Emmerich. Technical Data SKU: VT314-1TM Label: 25mm Einschraubfräser LOGU 0303 L57mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 25 mm Overall length: 57 mm Thread: M12 Thread height: 22 mm Cutting height: 35 mm Number of cutting edges: 4 Weight: 0.097 kg Torx key: T8 Torx screw: M3x7 Internal coolant: yes Special features Compatible with LOGU 0303 indexable inserts Compatible insert manufacturer: Kyocera Product type: Screw‑in milling cutter Intended for CNC milling applications FAQ Which inserts fit this cutter? The VT314-1TM is designed for LOGU 0303 indexable inserts and is compatible with inserts from Kyocera; specify LOGU 0303 geometry when ordering inserts. How does the internal coolant benefit machining? Internal coolant on the VT314-1TM supplies lubricant directly to the cutting zone, improving chip evacuation and thermal control to extend insert life and enhance surface finish. What is the correct fastening method for the insert? Insert clamping on the cutter uses a Torx screw (M3x7) tightened with a T8 key; this standardised system permits quick and secure insert changes. Is the cutter suitable for tight‑access milling tasks? Yes, the 25 mm diameter and 57 mm overall length make the cutter suitable for confined spaces where a compact tool body and reliable stiffness are required. What thread should the toolholder provide for mounting? The cutter uses an M12 screw‑in connection with a 22 mm thread height for a secure mount; ensure the toolholder accepts M12 screw‑in cutters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from a compact, high‑precision milling head that pairs RDMT 1003 indexable inserts with internal coolant and a sturdy M12 screw connection for reliable short‑reach operations; order this screw‑in cutter directly via Metav Werkzeuge or ask the consultants for tailored advice. Screw-in cutter VT100-1TM — 25 mm diameter, internal coolant (Teknik Cutting Tools) The screw-in cutter VT100-1TM is a purpose‑built milling head for RDMT 1003 indexable inserts, combining a compact 25 mm diameter with internal coolant to support precision machining in confined setups 25 mm diameter for compact milling Internal coolant for improved chip evacuation M12 screw-in connection, 22 mm thread length Compatible with RDMT 1003 indexable inserts Greater stability and accessibility in tight fixtures The compact 25 mm diameter and 55 mm overall length provide a small footprint that reduces overhang, improving rigidity during face or shoulder milling. Reduced overhang directly lowers vibration and runout, which results in a more consistent surface finish and extended insert life. With three cutting edges the tool balances chip load and cutting stability, enabling efficient removal rates in short‑reach operations without sacrificing dimensional control. The combination of a compact body and a secure screw‑in interface is designed to support repeatable set‑ups on production spindles and small horizontal milling centres. Improved tool life and surface quality through internal coolant Integrated internal coolant directs cutting fluid close to the cutting edge, aiding chip evacuation and reducing local cutting temperatures. This targeted cooling lowers thermal wear on the insert grades and helps maintain cutting geometry over longer cycles, which is particularly relevant when working with alloys or abrasive materials. For users unfamiliar with internal‑cool systems: the coolant path minimises chip recutting and flushes away heat and swarf, allowing higher effective cutting speeds and steadier surface integrity without complex external nozzle adjustments. Secure mounting, straightforward insert changes and maintenance A robust M12 screw connection with a 22 mm thread height provides a reliable mechanical interface for repeatable seating and torque transfer. Insert retention is handled with a Torx screw (T15) using an M3.5x8.5 fixing, which simplifies replacements and reduces downtime during tool changes. The cutter’s geometry and insert interface are designed for RDMT 1003 indexable inserts, easing inventory management where that insert family is standard. Clear, accessible fastening points mean maintenance procedures remain quick and unambiguous, supporting steady throughput in production environments. Production suitability and application focus Engineered for short‑reach milling tasks in industrial settings, this screw‑in milling head supports operations that demand precision and consistent repeatability rather than excessive reach. Its compact form factor makes it suitable for congested tool stacks, fixture work and small batch production where spindle accessibility is limited. The tool’s balanced design and coolant capability make it a pragmatic choice for manufacturers seeking to consolidate tooling types while maintaining process reliability and minimising the need for extensive spindle re‑setup. Speak with Metav Werkzeuge to discuss Teknik Cutting Tools screw‑in cutters with internal coolant and secure supply direct from Emmerich. Technical data SKU: VT100-1TM UID: VT100-1TM Brand: Teknik Makina Facts Diameter: 25 mm Overall length: 55 mm Thread height: 22 mm Thread: M12 Cutting edges: 3 Cutting-edge height: 33 mm Weight: 0.114 kg Torx key: T15 Torx screw: M3.5x8.5 Special features Internal coolant Compatible with RDMT 1003 indexable inserts Screw-in mounting system Compact short-reach design FAQ What insert type does this cutter accept? The cutter accepts RDMT 1003 indexable inserts; the VT100-1TM is designed specifically for this insert family to ensure correct seating and reliable chip control. How does the internal coolant benefit machining? Internal coolant in the VT100-1TM directs fluid to the cutting zone, improving chip evacuation and reducing tool temperature, which prolongs insert life and enhances surface finish. Is the tool suitable for use in confined fixturing? Yes, the 25 mm diameter and 55 mm overall length provide a compact profile ideal for tight fixtures and short‑reach milling tasks. What is the mounting interface and how secure is it? The cutter uses an M12 screw-in connection with a 22 mm thread height; this robust mounting ensures repeatable seating and reliable torque transmission for production use. Which fastening hardware is used for the inserts? Inserts are secured with a Torx screw (M3.5x8.5) tightened with a T15 Torx key, enabling quick and reliable insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, screw-in milling head that combines fast insert changes with reliable clamping and a small footprint for flexible workshop use; order directly via Metav Werkzeuge or request advice from our technical consultants. VT120TM screw-in cutter — 25 mm diameter, M12 thread by Teknik Makina The VT120TM screw-in cutter is a compact milling head designed for light to medium duty milling with RDMT 12T3 indexable inserts, ideal for tight setups and quick tool changes in production and repair shops 25 mm cutting diameter M12 screw-in thread Two cutting edges for balanced cutting 55 mm overall length Faster setup and shorter cycle times with screw-in design The screw-in design with a robust M12 thread and a modest overall length delivers a practical way to reduce tool change time and maintain machine accessibility. Thanks to the compact geometry and 25 mm cutting diameter, the tool is particularly suited to operations where space is limited but stability remains essential. The two cutting edges ensure even load distribution, which improves run stability and contributes to consistent surface quality. The assembly requires only a Torx driver, keeping clamp times predictable and repeatable for small-batch and series production alike. Reliable clamping and easy insert handling for continuous operation A secure clamping system is crucial for predictable machining. The head is prepared with a locking screw M3.5 and a Torx screw M3.5x8.5, operated with a Torx T15 key, allowing quick but secure replacement of indexable inserts. The specified 22 mm thread height and 33 mm cutting height are matched to the insert geometry, enabling confident seating of RDMT 12T3 indexable inserts and minimising micro-movement under cut. With a tool mass of just 0.106 kg, dynamic response is improved while still offering enough mass to dampen chatter in many common finishing and semi-finishing applications. Compact form factor that supports flexible workshop layouts The short 55 mm overall length and screw-in configuration make the head easy to integrate on arbors and holders where space is constrained. The reduced projection lowers bending moments and helps preserve spindle life when compared with longer tool assemblies. This compactness, combined with the standard M12 interface, suits both portable retrofit tasks and centralised CNC workstations, enabling shops to keep a smaller inventory of fixtures while achieving versatile machining options. Durable performance with predictable maintenance intervals Constructed for straightforward use, the cutter balances ease of maintenance with dependable machining characteristics. The combination of secure Torx fastening and straightforward insert indexing keeps routine servicing quick and low-risk. When paired with suitable RDMT 12T3 indexable inserts, the head supports repeatable parameters across production runs, helping to maintain consistent part tolerances and surface quality while keeping downtime to a minimum. For tailored advice or to secure stock for immediate production, contact Metav Werkzeuge today — Metav’s specialists in precision tools can confirm compatibility and delivery from our Emmerich warehouse Technical data Article number: VT120TM Manufacturer: Teknik Makina E-class: 21180806 ETIM: EC011860 Dimensions & weight Cutting diameter: 25 mm Overall length: 55 mm Thread: M12 Thread height: 22 mm Cutting height: 33 mm Cutting edges: 2 Weight: 0.106 kg Mounting & special features For RDMT 12T3 indexable inserts Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key size: T15 FAQ Which inserts fit this screw-in cutter? The head is specified for use with RDMT 12T3 indexable inserts; the VT120TM is configured to accept the standard geometry and seating of that insert series. How is the insert secured and changed? Inserts are secured with the supplied Torx screw (M3.5x8.5); removal and fitting are performed with a T15 Torx key for reliable, repeatable clamping. Is the cutter suitable for small machines with limited tool clearance? Yes, the 55 mm overall length and M12 screw-in interface make the cutter appropriate for confined spaces where projection needs to be minimised. What balance can be expected for serial machining? With two cutting edges and a compact design, the tool provides balanced cutting behaviour for many light and medium duty serial operations; machine-specific balancing should follow the spindle manufacturer’s guidance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, high-performance tool that combines a secure M12 screw connection, internal coolant and a two‑flute geometry for reliable chip control and consistent surface quality; order the screw‑in cutter directly via Metav Werkzeuge or ask the consultants if needed. Screw‑in cutter VT120-1TM — 25 mm, internal coolant, for RDMT 12T3 indexable inserts (Teknik Makina) The screw‑in cutter for RDMT 12T3 indexable inserts is a compact two‑flute milling tool engineered for short overhang operations and efficient coolant‑assisted cutting. Screw‑in cutter 25 mm diameter Internal coolant for improved chip evacuation Two cutting edges for smooth surface finish M12 screw connection, compact L55 mm design Enhanced machining performance with coolant‑assisted cutting The compact tool body delivers targeted performance: a 25 mm diameter cutter with internal coolant directs cutting fluid straight to the cutting zone, reducing thermal load and aiding chip evacuation. This targeted cooling helps to maintain insert geometry and reduces wear rate, which in turn supports longer service intervals and steadier part quality. The two‑flute configuration balances metal removal with surface finish, making the tool suitable for applications where controlled material removal and consistent results are priorities. Explaining briefly, an indexable insert is a replaceable cutting tip that allows rapid refresh of the cutting edge without regrinding, keeping process downtime to a minimum. Secure mounting and repeatable concentricity for production lines A reliable screw connection is essential in repetitive machining. The M12 threaded mounting and defined thread height 22 mm provide a secure interface that minimises runout and mechanical play during high‑load operations. The cutter’s compact overall length 55 mm and cutting height 33 mm reduce bending moments and improve rigidity compared with longer holders. The assembly uses a Torx fastening system (Torx key T15; Torx screw M3.5x8.5) to ensure consistent clamping torque and repeatable installation. Together, these design choices support stable cutting conditions and predictable component tolerances on the shop floor. Practical use, handling and workshop integration This screw‑in milling head is supplied for RDMT 12T3 insert geometry and is optimised for quick insert changes and minimal inventory complexity. The lightweight construction (approx. 0.106 kg) keeps handling simple during presetting and tool change routines. For workshops seeking to centralise tool stock without large holder inventories, the compact design reduces storage space while allowing fast on‑machine readiness. If further process parameters are required for integration into a CAM setup or a specific spindle configuration, technical advisors at Metav Werkzeuge can provide tailored guidance and supporting data. For reliable internal‑coolant performance and consistent mounting choose the Teknik Makina screw‑in cutter VT120-1TM — contact Metav Werkzeuge for ordering or technical consultation via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VT120-1TM Brand: Teknik Makina Product type: Screw‑in cutter Key measurements Diameter: 25 mm Overall length: 55 mm Cutting height: 33 mm Thread height: 22 mm Weight: 0.106 kg Number of cutting edges: 2 Thread: M12 Torx key: T15 Torx screw: M3.5x8.5 Internal coolant: Yes Special features For RDMT 12T3 indexable inserts Internal coolant channel Screw‑in mounting Two‑flute geometry Compact L55 mm design FAQ What insert type does this cutter accept? The cutter accepts RDMT 12T3 indexable inserts and is set up for quick insert changes on the VT120-1TM milling head. Is the tool suitable for use with internal coolant systems? Yes, the VT120-1TM features internal coolant delivery to the cutting edge to aid chip evacuation and reduce thermal load. How is the cutter secured to the machine or adapter? The tool uses an M12 screw connection with defined thread height and a Torx fastening (T15 key, M3.5x8.5 screw) for consistent clamping torque. What are the main dimensional limits to consider for setup? Key dimensions are a 25 mm diameter, cutting height 33 mm and overall length 55 mm; these values guide reach and clearance planning. Can this head be preset on tool measurement equipment? Yes; the compact, repeatable geometry and low weight of the VT120-1TM simplify presetting routines and handling at tool presetter stations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, reliable clamping and broad insert compatibility for consistent finishing in confined setups; order the VT174TM screw-in cutter directly via Metav Werkzeuge or consult our specialists for application advice. VT174TM screw-in cutter (25 mm, M12 thread) by Teknik Makina The VT174TM is a screw-in cutter designed for RPMT 10–12 indexable inserts, optimised for small-diameter milling and accurate finishing in limited workspaces. Compact 25 mm diameter for tight spaces M12 screw-in shank for secure mounting Compatible with RPMT 10–12 indexable inserts Two cutting edges for efficient material removal Lightweight at 0.109 kg for reduced spindle load High-precision cutting in a compact form The VT174TM combines a 25 mm diameter with a short 55 mm overall length to deliver accurate machining where accessibility is limited. Its compact geometry reduces tool overhang and vibration, which helps maintain a consistent surface finish and prolongs insert life. The tool’s two cutting edges provide a balance between material removal and control, making the cutter suitable for semi-finish and finish passes. For operations requiring repeatable results in small pockets or narrow jaws, this design ensures the required dimensional stability. Secure clamping and straightforward insert handling Clamping is achieved with an M12 screw-in interface and a dedicated M3.5 locking screw system, tightened using a T15 Torx key, which guarantees repeatable seat pressure and simple servicing. The use of standard RPMT 10–12 indexable inserts (RPMT 12) simplifies supply chains and reduces setup time when changing inserts. A driven, indexed insert system allows for rapid replacement and minimal downtime; the combination of M3.5x8.5 Torx screws and accessible tool geometry ensures service can be carried out quickly and safely at the machine. Material compatibility and machining performance Although intended primarily for general milling tasks with RPMT inserts, the cutter’s design supports a range of typical workshop materials when used with the appropriate grade of insert from recognised suppliers such as Mitsubishi. The short thread height of 22 mm and a cutting height of 33 mm provide a stable support for the insert, improving edge life under moderate cutting forces. The lightweight construction (0.109 kg) reduces additional load on the spindle, which is beneficial for high-speed finishing and for machines with lower power reserves. Operational benefits and workshop integration For production environments seeking predictable throughput, the VT174TM offers a compact, easy-to-manage tool body that integrates with existing insert assortments. The screw-in M12 mounting reduces inventory complexity compared with proprietary holders, while compatibility with widespread RPMT 10–12 inserts keeps replenishment straightforward. The tool’s modest mass and short overhang contribute to lower dynamic stress on the machine spindle, assisting with longer-term tool life and reduced maintenance intervals—attributes that support operational efficiency on the shop floor. For tight-space milling tasks trusting Teknik Cutting Tools' VT174TM is recommended—order via Metav Werkzeuge or contact Metav Werkzeuge for tailored technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: VT174TM Brand: Teknik Makina Product: screw-in cutter for RPMT 10–12 indexable inserts Compatible inserts: RPMT 12 Compatible insert manufacturer: Mitsubishi Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 Core specifications Diameter: 25 mm Thread: M12 Overall length: 55 mm Thread height: 22 mm Cutting height: 33 mm Cutting edges: 2 Weight: 0.109 kg Features and compatibility For RPMT 10–12 indexable inserts Suitable for finishing and semi-finish operations Compact design for limited-access machining Standardised fastening for simple maintenance Compatible with Mitsubishi RPMT 12 inserts FAQ Which inserts fit this cutter? The cutter accepts RPMT 10–12 indexable inserts; the body is specified for RPMT 12 sizes and works with common grades from Mitsubishi. How is the insert secured and serviced? Inserts are secured with an M3.5 locking screw tightened with a T15 Torx key; the M3.5x8.5 Torx screw allows quick replacement and reliable clamping. Is the VT174TM suitable for tight internal pockets? Yes — the 25 mm diameter and 55 mm overall length make the tool appropriate for confined spaces where reduced overhang improves stability. What are the key mounting requirements? The tool uses an M12 screw-in shank; ensure the machine arbor or adapter accepts M12 screw-in holders and observe correct mounting torque. Will the cutter suit high-speed finishing? The lightweight body (0.109 kg) and short overhang support high-speed finishing when paired with appropriate inserts and machine parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust mounting, reliable coolant delivery and precise insert compatibility for consistent milling results; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Screw-in milling cutter for XEKT 1904 indexable inserts – Ø25 mm, internal coolant (Teknik Makina) A Screw-in milling cutter engineered for XEKT 1904 indexable inserts, offering a compact Ø25 mm body and integrated internal coolant for controlled chip removal. 25 mm diameter, L79 mm overall length Internal coolant for improved chip evacuation Compatible with XEKT 1904 indexable inserts (Korloy) M12 screw-in thread with 2 cutting edges Consistent mounting and repeatability for indexable inserts The screw-in design with an M12 thread enables secure attachment and rapid replacement, ensuring repeatable tool positioning in serial production. Built to accept XEKT 1904 indexable inserts, the cutter supports quick insert changes without complex adaptations, which reduces machine downtime and increases throughput. The compact Ø25 mm body fits tight tool inventories while maintaining stable concentricity for high-quality surface finishes. Controlled cutting zone and longer insert life Integrated internal coolant directs lubricant and coolant precisely to the cutting zone, improving heat management and chip evacuation. Combined with 2 cutting edges and a cutting height 55 mm, this results in more uniform wear across the insert, extending component life and lowering overall tooling costs per part. The combination of a short L79 mm overhang and a lightweight construction helps to reduce vibration, leading to a smoother cut and predictable machining performance. Practical design for workshop efficiency Maintenance and routine handling are simplified with the Torx fastening system: Torx T15 for the screw drive and a matching M4x8.5 Torx screw that secures the head. The unit’s low mass supports rapid acceleration on CNC spindles and reduces inertial loads during tool changes. Manufactured by Teknik Makina and listed under SKU VT260-1TM, the tool integrates into standard holders and common workshop workflows, making it a pragmatic choice for operations that require both flexibility and consistent repeatability. Contact Metav Werkzeuge for tailored technical guidance and to secure the Teknik Makina VT260-1TM screw-in milling cutter with internal coolant for dependable milling performance at your site. Technical data SKU: VT260-1TM Manufacturer: Teknik Makina Product type: Screw-in milling cutter Facts Diameter: 25 mm Overall length: 79 mm Weight: 0.12 kg Cutting edges: 2 Cutting height: 55 mm Special features Internal coolant: yes Thread: M12 Suitable for: XEKT 1904 indexable inserts Compatible insert manufacturer: Korloy Torx key: T15 Torx screw: M4x8.5 FAQ Is this cutter compatible with XEKT 1904 indexable inserts? Yes. The cutter accepts XEKT 1904 indexable inserts and is specified for use with Korloy inserts for reliable seating and repeatable clamping. Does the tool offer through-coolant capability? The unit features internal coolant, which supplies lubricant and coolant directly to the cutting edge to support chip control and thermal management. What is the mounting thread and how secure is the attachment? The tool is fitted with an M12 thread for screw-in mounting, delivering a secure connection that maintains concentricity during milling operations. Which fastener is used for the insert head? The head is retained with a Torx screw system; the specified driver size is Torx T15 and the screw dimension is M4x8.5. What is the SKU for ordering and identification? The product is listed as VT260-1TM, manufactured by Teknik Makina, for straightforward ordering and inventory management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-performance screw-in milling cutter with a secure M12 mount and compatibility with XEKT 1904 indexable inserts for reliable, consistent milling operations; order directly via Metav Werkzeuge or discuss specifications with our consultants. Teknik Makina 25 mm screw-in cutter for XEKT 1904, M12 thread The 25 mm screw-in cutter for XEKT 1904 indexable inserts is a compact milling head designed for precise material removal in constrained setups and for straightforward insert replacement. 25 mm diameter with M12 screw connection Compatible with XEKT 1904 indexable inserts Two-edge design for stable cutting Compact 79 mm overall length, lightweight Precision and performance for repeatable milling results The compact head is engineered to deliver stable cutting with minimal vibration thanks to its two cutting edges, translating into more consistent component quality and extended tool life. The M12 screw connection provides a secure, concentric mounting that reduces runout and improves surface finish in short-reach operations. Compatibility with XEKT 1904 indexable inserts ensures access to established insert geometries and grades; the holder accepts Korloy-manufactured inserts for broad material coverage. By focusing on concentricity and edge stability, the design helps to reduce scrap rates and maintain throughput in production environments. Fast insert changes and low-maintenance operation Maintenance and tool changes are simplified by the Torx fastening system: the head uses a T15 Torx key and an M4x8.5 fixing screw to retain the insert, enabling secure clamping and predictable torque. This setup reduces changeover time and the risk of incorrect tightening, improving uptime on the shop floor. The option for swift replacement of indexable inserts lowers operational complexity and helps keep machines running with minimal interruption. Clear access to the fastening point and standardised hardware make inventory and training simpler for workshop staff. Compact design that fits tight machine envelopes With an overall length of 79 mm and a total mass of 0.12 kg, the cutter minimises overhang and inertia at the tool centre, which is advantageous where tool clearance and stability are critical. The moderate length helps to reduce bending moments in slender setups, while the lightweight construction supports higher spindle dynamics and faster acceleration. These characteristics make the head suitable for confined tool stations and short-reach finishing passes where a small, well-balanced cutter improves handling and process stability. For tailored advice on integrating the Teknik Makina screw-in cutter into specific machines or applications, contact Metav Werkzeuge for product guidance and procurement support — our specialists will discuss compatibility, lead times and technical details. Technical data SKU: VT260TM Manufacturer: Teknik Makina Product type: Screw-in milling cutter Compatible inserts: XEKT 1904 (Korloy) Numbers / Core technical data Diameter: 25 mm Overall length: 79 mm Thread: M12 Thread height: 24 mm Cutting edges: 2 Cutting edge height: 55 mm Weight: 0.12 kg Torx key: T15 Torx screw: M4x8.5 Special features Compatible with Korloy XEKT 1904 indexable inserts Secure M12 mounting for low runout Two-edge geometry for steady machining Compact form factor for constrained setups FAQ How does the cutter secure the indexable inserts? The cutter uses an M4x8.5 fixing screw accessed with a T15 Torx key to clamp XEKT 1904 indexable inserts securely in the seat, as specified for the VT260TM holder. Is the tool suitable for tight tool stations on CNC machines? Yes, the compact 79 mm overall length and 0.12 kg weight make the screw-in milling cutter well suited to confined setups where reduced overhang and low inertia are required. Which insert manufacturer is compatible with this holder? The holder is compatible with Korloy XEKT 1904 indexable inserts; the interface is designed to accept the standard insert geometry for reliable seating and repeatability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact 25 mm diameter, a stable M12 screw-in connection and proven compatibility with APKT 1604 indexable inserts for reliable 90° shoulder milling — order the tool from Metav Werkzeuge or consult our specialists for application advice. Screw-in milling cutter VT160TM — 25 mm diameter, 90° shoulder, Teknik Makina A Screw-in milling cutter designed for precise 90° shoulder milling with APKT 1604 indexable inserts in confined setups 90° cutting angle for shoulder milling Compatible with Korloy APKT 1604 inserts M12 screw-in thread, 25 mm diameter Secure Torx clamping, M4x10 screw Accurate shoulder milling where space is limited The Screw-in milling cutter provides a compact solution for tight fixtures and multi-axis setups. With a 25 mm outer diameter and a defined 90° cutting angle, the tool is optimised for shoulder and face milling operations that demand perpendicular walls and repeatable corner geometry. Using established APKT 1604 indexable inserts reduces per-part tooling cost since worn cutting edges are replaced instead of the whole head. The result is predictable component tolerances and simplified spare-part logistics for production-focused workshops. Secure clamping and low-vibration performance for repeatability A robust M12 thread with 22 mm engagement and a close centre of mass (total length 55 mm, weight 0.107 kg) gives the assembly high clamping stability and low overhang oscillation. The insert is secured with a M4x10 Torx screw (Torx key size T15), providing consistent seat loading and repeatable positioning of the indexable cutting edge. With 2 cutting edges and a cutting height of 33 mm, the configuration balances material removal with tool life and allows for quick insert changes, reducing machine downtime and improving process uptime. Integration into machining processes and procurement advantages The tool’s adherence to common insert standards simplifies toolholder inventory: it accepts APKT 1604 inserts widely available from major suppliers such as Korloy. The compact design suits jobbing shops and production cells that need high process reliability without complex tool management. Supplied by a trusted distribution partner, the product benefits from Metav’s European logistics filter in Emmerich, which supports a broad catalogue and dependable supply chains — a practical advantage for buyers aiming to consolidate suppliers and secure consistent deliveries. For dependable 90° shoulder milling select the Teknik Makina VT160TM from Metav Werkzeuge — contact Metav Werkzeuge GmbH in Emmerich for ordering or technical clarification via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VT160TM Manufacturer: Teknik Makina SKU: VT160TM Facts Diameter: 25 mm Overall length: 55 mm Cutting height: 33 mm Thread engagement height: 22 mm Thread: M12 Cutting edges: 2 Weight: 0.107 kg Cutting angle: 90° Torx screw: M4x10 Torx key size: T15 Special features For APKT 1604 indexable inserts Compatible with Korloy inserts Designed for 90° shoulder milling Compact screw-in mounting for tight setups FAQ Which indexable inserts fit this cutter? The cutter accepts APKT 1604 indexable inserts; Korloy APKT 1604 inserts are a compatible option for the VT160TM. How is the insert clamped? The insert is secured with a M4x10 Torx screw; a T15 key is required to achieve the correct clamping torque and repeatable seating. What machining tasks is the tool best suited for? This tool is intended for 90° shoulder and face milling where a compact tool body and repeatable corner geometry are required. Is the screw-in connection durable for continuous production? The M12 screw-in mounting with 22 mm engagement provides a stable connection suitable for regular production use when mounted correctly. Can the cutter be used on small machining centres? Yes — the compact 25 mm diameter and short overall length make the tool suitable for machines with limited clearance or short overhangs. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, screw-in design combined with proven compatibility for APXT 1003 indexable inserts to reduce tool change time and maintain consistent machining results; available directly via Metav Werkzeuge or through specialist advice from our team. Screw-in Cutter VT140TM — 25 mm diameter, M12 thread by Teknik Makina The Screw-in Cutter VT140TM is a compact milling head designed for indexable-insert turning and milling applications, offering secure clamping and straightforward insert replacement for production and maintenance environments 25 mm cutter diameter M12 screw-in thread Fits APXT 1003 indexable inserts Three cutting edges for steady cutting Faster insert changes through secure Torx clamping The robust Torx screw (M2.5x5.5) and corresponding T8 key deliver a positive clamping interface that simplifies insert replacement and reduces downtime. This secure fastening system keeps the insert pocket consistently aligned, so cycle times remain stable and rework is minimised. For workshops moving from brazed or solid tools to indexable systems, the reduced handling and simplified spare-part management translate into measurable time savings per tool change, while compatibility with Korloy-produced inserts broadens sourcing options. Consistent cutting performance with compact geometry With a 25 mm diameter, three cutting edges and a 90° cutting angle, the tool provides a balanced mix of rigidity and accessibility for standard face and shoulder operations. The cutter’s cutting height (33 mm) and overall length (55 mm) are optimised to keep overhang low and vibration under control, improving surface finish and tool life. Operators unfamiliar with indexable tooling will find the geometry predictable: one can expect steady chip evacuation and reliable contact conditions, which reduces the need for frequent process adjustments. Practical workshop integration and predictable handling The screw-in interface with an M12 thread and a 22 mm thread engagement offers simple mounting into compatible holders and systems, keeping inventory lean. At 0.135 kg, the head is light enough for rapid handling yet substantial enough to contribute to cutting stability. Designed for APXT 1003 indexable inserts, this head supports a cost-efficient approach to tooling by allowing selective use of inserts for wear-prone operations while the body remains reusable. Technical buyers and production planners benefit from this separation: replacement cost is limited to the insert, not the entire tool body. For a tailored quotation or to discuss workshop integration with the VT140TM, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and delivery options. Technical Data SKU: VT140TM Brand: Teknik Makina Product: Screw-in cutter for indexable inserts Compatibility: for APXT 1003 indexable inserts ECLASS: 21180806 ETIM: EC011860 Diameter: 25 mm Overall length: 55 mm Cutting height: 33 mm Thread: M12 Thread engagement height: 22 mm Cutting edges: 3 Cutting angle: 90° Weight: 0.135 kg Torx screw: M2.5x5.5 Torx key: T8 Compatible insert manufacturer: Korloy Design: screw-in milling head Application: indexable-insert milling FAQ What inserts are compatible with this cutter? The cutter accepts APXT 1003 indexable inserts; Korloy inserts listed as compatible are suitable for the VT140TM head. Which toolholder interface is required for mounting? A holder with an M12 screw-in thread and sufficient clearance for the head’s 55 mm overall length is required to mount the VT140TM securely. What size and type of screw secures the insert? Insert clamping is performed with a Torx screw M2.5x5.5; the recommended driver size is a T8 bit for consistent torque. Is the cutter suitable for heavy shoulder milling? The compact geometry, three cutting edges and 90° cutting angle provide stable contact suitable for routine shoulder and face milling; suitability for heavy roughing depends on specific machine and process parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com