Gibt es einen Hahn und Kolb Online Shop?

Secure reliable, high‑feed milling with a 25 mm diameter head, internal coolant and compatibility with Taegutec BLMP 0904 indexable inserts. The combination of a stable screw‑in mounting and three cutting edges delivers consistent chip control and reduced machining time. Order the VT265-1TM via Metav Werkzeuge or consult our specialists for tool configuration and fast delivery. VT265-1TM screw-in milling cutter – 25 mm, internal coolant (Teknik Makina) VT265-1TM screw-in milling cutter is designed for indexable‑insert milling with BLMP 0904 inserts, offering compact mounting and controlled coolant supply for workshop and light production use. 25 mm diameter for versatile milling Internal coolant for improved chip evacuation Three cutting edges for smooth material removal Compatible with Taegutec BLMP 0904 inserts Boosted throughput with compact indexable design The VT265-1TM packs productivity into a compact screw‑in head: a 25 mm diameter and three cutting edges allow higher feed rates with stable cutting engagement. Compatibility with Taegutec BLMP 0904 indexable inserts simplifies tooling choices and reduces inventory complexity for shops that standardise on this insert family. The result is fewer tool changes, less downtime and a measurable increase in throughput for short to medium production runs. Controlled cooling for longer tool life and process reliability Built‑in internal coolant directs lubricant to the cutting zone, which improves heat control and supports consistent chip formation. By keeping the insert seat and cutting edge cooler, the cooling channel helps to reduce thermal wear and edge degradation, so insert life is extended and regrinding intervals are less frequent. This technical advantage translates into more reliable cycles and lower operating cost per component. Secure mounting and predictable repeatability The screw‑in head is secured via a robust 12 mm thread with a 20 mm thread height, ensuring firm seating and concentricity during heavy engagement. The insert clamping relies on a Torx drive; the required key is T10 and the fastening screw is M3.5x8.5, enabling quick, repeatable insert changes with standard maintenance tools. With a 55 mm overall length and a substantial cutting‑edge engagement, the geometry supports stable milling while the low mass contributes to reduced spindle load. Simple handling, wide application range Maintenance is straightforward: indexed inserts are replaced quickly using the Torx screw, and routine checks focus on insert condition rather than complex regrinds. The head’s modest weight (0.113 kg) eases handling during tool set‑up and minimises centrifugal influence at higher spindle speeds. Suited to general face and shoulder milling duties in workshops and small series production, the cutter offers an efficient balance between tool life, ease of service and machining performance. For application advice, stock availability or to request the VT265-1TM from Teknik Makina, contact Metav Werkzeuge in Emmerich — info@metav-werkzeuge.com | +49 2822 7131930; our team can recommend the correct inserts and mounting configuration for specific tasks Technical data SKU: VT265-1TM Manufacturer: Teknik Makina Product type: Screw-in milling cutter Compatible inserts: BLMP 0904 (Taegutec) Facts Diameter: 25 mm Overall length: 55 mm Weight: 0.113 kg Cutting edges: 3 Cutting-edge height: 35 mm Thread height: 20 mm Thread: 12 Special features Internal coolant Torx key: T10 Torx screw: M3.5x8.5 Compatible insert manufacturer: Taegutec FAQ Which indexable inserts fit this cutter? The VT265-1TM accepts BLMP 0904 indexable inserts; Taegutec BLMP 0904 inserts are recommended for optimum fit and performance. Does the cutter provide internal coolant? Yes, the VT265-1TM features internal coolant to the cutting zone for improved temperature control and chip evacuation. What fasteners and tools are needed for insert changes? Insert clamping uses a Torx screw M3.5x8.5 and a T10 Torx key; these are standard service items for the cutter. What applications suit this screw‑in head? The head is intended for face and shoulder milling in workshop and light production environments where compact, indexable tooling and reliable coolant supply are required. What are the key dimensions and mass? Key dimensions: 25 mm diameter, 55 mm overall length, 35 mm cutting‑edge height; mass 0.113 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable milling performance and straightforward integration are provided by the combination of a Ø 25 mm head and an M12 thread, together with compatibility for LNMU 0303 indexable inserts. Order the VT304TM via Metav Werkzeuge for secure supply, or request advice from the consultants when technical clarification is needed. Screw-in milling cutter VT304TM – Ø 25 mm, M12 thread (Teknik Makina) Screw-in milling cutter VT304TM — compact milling head for indexable inserts, designed for precise and repeatable milling operations using LNMU 0303 inserts Ø 25 mm head diameter M12 screw-in thread 4 cutting edges for stable cutting Compatible with LNMU 0303 indexable inserts Precision and productivity in one compact head The VT304TM screw-in milling cutter combines a compact Ø 25 mm cutting head with an M12 thread, offering a reliable interface for quick tool changes and secure clamping. The geometry with 4 cutting edges supports steady chip removal and reduced vibration, which helps to maintain consistent surface finish and prolong insert life. Compatibility with LNMU 0303 indexable inserts ensures wide availability of cutting grades and geometries, enabling optimisation for different workpiece requirements. The robust mounting and predictable run-out contribute directly to shorter cycle times and reliable repeatability in serial production. Simple handling and fast insert replacement Insert changes are designed to be quick and toolroom-friendly: the cutter uses a Torx M2.5x7 clamping screw and requires a T8 Torx key for secure fixation. This standardised fastening enables safe, repeatable seating of the insert without the need for special tools, reducing downtime during shifts or batch changes. The screw-in design allows straightforward replacement of worn heads and rapid integration into existing toolholders with compatible screw-in threads, making the component suitable for mixed production environments where flexibility and uptime matter. Integration into existing tooling systems Designed specifically for indexable insert milling tasks, this milling head fits insert grade and form LNMU 0303 and is listed as compatible with the TNGLY-OKE insert series from the specified manufacturers. The screw-in mounting and standardised interface permit smooth integration with a variety of toolholders and setups found in modern workshops. For operations that require predictable tool offsets and quick regrinding cycles, the consistent geometry reduces the need for repeated alignments, saving setup time and simplifying process control. Dependable supply and partnered quality assurance Produced by Teknik Makina and offered via Metav’s distribution network, the cutter benefits from a supply chain that emphasises parts availability and quality screening. Metav’s position as a European quality filter means workshops gain access to precise tooling with reliable delivery, backed by decades of metrology and tooling experience. Where consistent procurement and traceable specifications are essential, this milling head forms part of a broader approach to reduce supplier count while maintaining performance standards on the shopfloor. For a reliable supply of the VT304TM screw-in milling cutter with M12 thread and Ø 25 mm head, contact Metav Werkzeuge for direct ordering or to request detailed technical consultation. Technical data Article number: VT304TM Designation: Screw-in milling cutter for LNMU 0303 indexable inserts Manufacturer: Teknik Makina Dimensions & key values Diameter: 25 mm Thread: M12 Overall length: 57 mm Cutting edges: 4 Torx screw: M2.5x7 Torx key size: T8 Compatibility & special features Compatible with LNMU 0303 indexable inserts Compatible with TNGLY-OKE insert series Screw-in mounting for quick replacement Standardised clamping with Torx screw FAQ Which indexable inserts fit this milling head? The milling head is specified for LNMU 0303 indexable inserts and is also listed as compatible with the TNGLY-OKE series for flexible grade selection. What fastening hardware is required for insert changes? Replacement and clamping use a Torx M2.5x7 screw tightened with a T8 Torx key for secure seating of the insert. What are the main dimensional values of the tool? Key dimensions are Ø 25 mm head diameter, M12 screw-in thread and an overall length of 57 mm. How many cutting edges does the head provide and what is the benefit? The tool has 4 cutting edges, which helps to stabilise cutting forces and improve surface finish while extending individual insert life through even wear distribution. Who manufactures the VT304TM and who supplies it? The VT304TM is produced by Teknik Makina and supplied via Metav Werkzeuge for verified quality and distribution. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, screw-in milling cutter that pairs secure M12 mounting with proven RDMT 1003 indexable inserts for stable machining and predictable tool life; its three cutting edges and modest mass support high-speed finishing while lowering spindle load — order via Metav Werkzeuge or consult the specialists for fast availability. Screw-in milling cutter VT100TM — Ø 25 mm, for RDMT 1003 indexable inserts (Teknik Cutting Tools) The Screw-in milling cutter VT100TM is a compact cutter head designed for indexable RDMT 1003 inserts, suitable for small- to medium-sized milling operations where secure clamping and quick insert changes are required Fits RDMT 1003 indexable inserts Ø 25 mm with M12 thread Three cutting edges for steady cutting Secure M3.5 locking screw system Compact design, 55 mm overall length Predictable clamping and stable cutting for consistent surface finish The VT100TM is engineered for secure clamping and repeatable performance by combining a standard M12 screw-in connection with a dedicated M3.5 locking screw and a Torx screw drive. This arrangement reduces micro-movement between insert and cutter, which in turn lowers vibration and improves surface quality. With a nominal Ø 25 mm body and three cutting edges, the head balances rigidity and cutting engagement; the 22 mm thread height ensures reliable seating in the toolholder, while the modest mass (approx. 0.114 kg) minimises additional spindle load. These measurable design choices lead directly to fewer rejects and a steadier process in serial and job-shop environments. Faster insert change and lower tool inventory for real productivity gains Standardisation around RDMT 1003 indexable inserts enables rapid replacement and reduces the variety of items that must be stocked. The cutter’s Torx screw specification (T15) and the M3.5x8.5 screw make insert swaps straightforward with common workshop tools, contributing to shorter setup times and higher spindle uptime. The 33 mm cutting height and 55 mm overall length provide sufficient reach for many face and shoulder milling tasks without unnecessary overhang; the result is a practical tool that supports lean workflows and predictable cycle times — an explicit efficiency gain that pays off across repeated operations. A dependable option for mixed production and workshop settings Chosen for its compact footprint and compatibility, this screw-in head is well suited to applications that demand repeatability rather than exotic geometries. The combination of three cutting edges and secure locking reduces the risk of insert displacement under intermittent loads, while the standardised insert family simplifies procurement. As a component from Teknik Cutting Tools offered through Metav Werkzeuge, the unit benefits from straightforward sourcing and the distributor’s quality-filtered stock in Emmerich, helping maintain consistent supply for production schedules. For secure integration into existing tooling systems and reliable stock information, contact Metav Werkzeuge for product availability and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 — immediate assistance from Emmerich's specialists Technical data Article number: VT100TM Name: Einschraubfräser (Screw-in milling cutter) Additional designation: for RDMT 1003 Indexable Inserts Manufacturer: Teknik Makina Facts Diameter: 25 mm Thread: M12 Thread height: 22 mm Cutting height: 33 mm Cutting edges: 3 Overall length: 55 mm Weight: 0.114 kg Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 SKU: VT100TM Special features For RDMT 1003 indexable inserts Screw-in mounting Three-edge geometry Torx T15 screw system FAQ What insert type is compatible with this cutter? The cutter accepts RDMT 1003 indexable inserts; the specification in the VT100TM is tailored for that insert family. Which thread and mounting are used for the cutter head? The VT100TM uses an M12 screw-in mounting with a 22 mm thread height for secure seating. How are the inserts secured in the tool? Inserts are fixed using an M3.5 locking screw and a Torx T15 drive; the Torx screw is M3.5x8.5. How many cutting edges does the tool provide and what is the body diameter? The tool features three cutting edges and a body diameter of 25 mm, optimised for steady cutting and reduced vibration. Is the cutter suitable for quick tool changes in a production environment? Yes — standardised RDMT 1003 inserts and the Torx T15 screw allow for rapid replacement and lower tool variety requirements. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the compact M12 screw-in mounting with a 25 mm cutting diameter and compatibility with RPMT 10-12 indexable inserts for repeatable, small‑diameter milling. Order the screw‑in cutter directly via Metav Werkzeuge or consult our technical team for specification advice. VT180TM Screw‑in cutter by Teknik Makina — M12 thread, 25 mm diameter, for RPMT 10-12 inserts VT180TM is a precision screw‑in cutter designed for compact milling tasks and CNC pocketing using RPMT series indexable inserts M12 screw‑in mounting for secure fixture 25 mm cutting diameter for compact milling Compatible with RPMT 10 indexable inserts Lightweight 0.084 kg for fast tool changes Secure mounting for predictable rigidity and repeatability The VT180TM is engineered around an M12 screw‑in connection that provides a compact, rigid interface for short overhang applications. The combination of the M12 thread and a thread height 22 mm ensures stable seating in holders, reducing vibration and improving repeatability on successive parts. The modest overall length of 55 mm and the 25 mm cutting diameter make this tool particularly suited to close‑tolerance pocketing and finishing operations where space and stiffness are critical. The low mass improves dynamic response during spindle acceleration and deceleration. Cost-effective performance with RPMT 10‑12 indexable inserts Compatibility with RPMT 10-12 indexable inserts allows economical turning of cutting edges and quick insert changes to maintain productivity. The head accepts RPMT 10‑sized inserts commonly offered by Mitsubishi, enabling access to a wide range of grades and chip‑breaking geometries for differing materials. The tooling body supports 3 cutting edges, paired with a cutting height 33 mm, to balance material removal with smooth chip evacuation. By using indexable inserts, tool life is effectively extended and downtime for regrinding is eliminated, providing clear cost‑benefit in batch and serial production. Quick serviceability and workshop integration Maintenance and insert changes are straightforward: the cutter uses a locking screw M3,5 and a Torx fixing screw M3,5x8,5 secured with Torx T15, enabling fast, tool‑standardised servicing on the shop floor. At just 0.084 kg, the body is easy to handle during tool set‑up and quick changes, shortening non‑productive time. The compact design integrates readily with common screw‑in holders and small‑diamence tool stations found in CNC milling and general workshop environments, supporting efficient changeover routines and consistent part quality. For compact, reliable M12 screw‑in cutters from Teknik Cutting Tools, contact Metav Werkzeuge in Emmerich for tailored supply and technical guidance — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: VT180TM Manufacturer: Teknik Makina Product: Screw‑in cutter for RPMT 10-12 Indexable Inserts ECLASS: 21180806 ETIM: EC011860 Core specifications Diameter: 25 mm Thread: M12 Total length: 55 mm Cutting height: 33 mm Thread height: 22 mm Cutting edges: 3 Weight: 0.084 kg Special features Locking screw: M3,5 Torx screw: M3,5x8,5 Torx key: T15 Compatible inserts: RPMT 10 Insert manufacturer compatibility: Mitsubishi FAQ Is the cutter compatible with RPMT 10 inserts from Mitsubishi? Yes — the VT180TM is specified for RPMT 10-12 indexable inserts and lists Mitsubishi as a compatible insert manufacturer. What mounting thread does the tool use? The tool uses an M12 screw‑in thread with a thread height of 22 mm for secure seating. How many cutting edges does the head support and what is the cutting height? The tool body supports 3 cutting edges and provides a cutting height of 33 mm. Which fastening hardware is required for insert retention? Insert retention uses a locking screw M3,5 together with a Torx screw M3,5x8,5, tightened with a Torx T15 key. Is the VT180TM suited to compact CNC tool stations? Yes — with a 25 mm cutting diameter, 55 mm total length and lightweight construction, the body is optimised for compact CNC setups and short overhang applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from efficient material removal and a reliable coolant path: the 25 mm screw-in cutter delivers stable cutting with its four cutting edges and internal coolant channel, while the secure M12 mount keeps downtime low. Order the tool directly via Metav Werkzeuge or contact our consultants for application support. VT226-1TM 25 mm screw-in cutter for APMT 0903 indexable inserts — Teknik Makina VT226-1TM is a screw-in milling head designed for high-productivity face and slot milling using APMT 0903 indexable inserts; it combines compact dimensions with internal coolant for controlled chip evacuation. 25 mm diameter for precise roughing Internal coolant for stable cutting Compatible with APMT 0903 Korloy inserts Secure M12 screw-in mount, 22 mm thread High material removal with consistent surface quality The compact milling head offers a 25 mm diameter and four cutting edges, enabling higher feed per tooth at reduced vibration levels. The combination of a robust clamping design and the internal coolant channel helps maintain a consistent cutting temperature, which reduces insert wear and supports predictable tool life. This results in fewer tool changes and more time on the spindle, improving throughput in batch and continuous production. Secure mounting and fast insert handling for busy shops A solid M12 screw-in connection with a 22 mm thread height provides a reliable mechanical interface to toolholders and adaptors, lowering the risk of loosening under heavy cuts. Insert retention relies on a Torx screw specification (Torx T8, screw M2.5x5.5), which streamlines indexable insert replacement and keeps changeover times short. The lightweight construction (≈ 0.116 kg) reduces spindle load and is advantageous when balancing multi-head setups or when rapid tool acceleration is required. Coolant-through design and compatibility that reduce process risk The internal coolant feed ensures directed fluid delivery to the cutting zone, improving chip evacuation and cooling for more aggressive cutting strategies. Compatibility with Korloy APMT 0903 inserts widens the choice of grades and geometries for finishing or roughing operations, allowing process optimisation without changing the tool body. The milling head is engineered for repeatable seating and minimal runout, supporting dimensional consistency across serial parts. Practical handling and maintenance that keep production running Maintenance is simplified by standardised fastening and available Torx tooling; routine checks and insert changes can be carried out quickly at the machine. The tool’s specification—compact length and predictable centre of gravity—facilitates handling in automated tool changers and manual tool stations alike. Routine monitoring of insert wear combined with the coolant-through capability extends the operational window between maintenance intervals, supporting lean manufacturing workflows. Secure your production with Teknik Makina’s VT226-1TM screw-in cutter — contact Metav Werkzeuge for technical advice and fast supply from Emmerich. Technical data SKU: VT226-1TM Brand: Teknik Makina Product type: Screw-in cutter for indexable inserts Compatible inserts: APMT 0903 (Korloy) Label: 25mm Einschraubfräser APMT 0903 L57mm mit Innenkühlung Key figures Diameter: 25 mm Overall length: 57 mm Weight: 0.116 kg Thread: M12 Thread height: 22 mm Cutting edges: 4 Cutting-edge height: 35 mm Torx key: T8 Torx screw: M2.5x5.5 Special features Internal coolant (coolant-through) Designed for APMT 0903 indexable inserts Secure screw-in mounting for stability Lightweight design for reduced spindle load FAQ What inserts fit this cutter? The VT226-1TM screw-in cutter is designed for APMT 0903 indexable inserts and is compatible with Korloy-manufactured APMT 0903 grades. Does the tool support coolant-through capability? Yes; the milling head features an internal coolant channel that delivers fluid directly to the cutting zone to aid chip evacuation and tool life. What fastening specification is required for insert replacement? Insert fastening uses a Torx system: Torx T8 key and screw M2.5x5.5 for secure and repeatable clamping. Is the cutter suitable for automated tool changers? The compact overall length and M12 screw-in mount make the tool suitable for automated toolholder systems where standard screw-in interfaces are used. Which SKU should be ordered for this configuration? Order SKU VT226-1TM for the 25 mm screw-in cutter configured for APMT 0903 inserts with internal coolant. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust cutter that combines a Ø25 mm cutting diameter, a secure M12 thread connection and compatibility with LNMX 0603 indexable inserts for reliable, repeatable milling. Order the screw-in milling cutter directly via Metav Werkzeuge or consult our specialists for application advice. Screw-in milling cutter VT154TM – for LNMX 0603 indexable inserts, Ø25 mm, M12 thread | Teknik Makina The Screw-in milling cutter VT154TM is a purpose-built screw-in milling head for light to medium-duty milling with LNMX 0603 indexable inserts, designed for secure clamping and rapid insert replacement in production and maintenance environments. Ø 25 mm cutting diameter M12 threaded shank for secure mounting Four cutting edges for balanced performance Compatible with LNMX 0603 inserts (Korloy) Consistent cutting performance through compact geometry The design focuses on dimensional stability: a compact head with a Ø25 mm cutting diameter and an M12 thread delivers a rigid connection to the toolholder, reducing vibration and improving surface finish. The configuration with 4 cutting edges provides a balanced cutting action that helps maintain steadier chip formation and tool life. For workshops assessing cutter balance and run-out behaviour, this geometry supports reproducible results on short- to mid-length tool overhangs while keeping the cutting forces within controlled limits. Fast insert changes and straightforward fastening Maintenance and downtime are reduced by the simple fastening concept: the cutter uses a Torx M3x7 screw secured with a T8 key, enabling quick insert changes without specialised clamping equipment. The retention concept is compatible with standard LNMX 0603 indexable inserts, so replacement parts from recognised manufacturers such as Korloy are straightforward to fit. The overall length 59 mm keeps the assembly compact, making access easier in tighter fixture arrangements and speeding up service cycles. Practical benefits for production and service environments For job shops and contract manufacturers seeking predictable throughput, the combination of indexable inserts and a screw-in mounting system reduces tooling inventory complexity and simplifies reconditioning. The cutter supports modularity: the use of established indexable inserts keeps running costs controllable while allowing quick adaptation to different materials by changing insert grades. Supplied by a reputable source, the item is suitable where reliable supply and consistent part quality are required to keep production schedules stable. For supply enquiries or technical advice on the Teknik Makina screw-in milling cutter VT154TM and its compatibility with LNMX 0603 indexable inserts, contact Metav Werkzeuge GmbH in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Item / SKU: VT154TM Product name: Screw-in milling cutter for LNMX 0603 indexable inserts Manufacturer: Teknik Makina eClass: 21180806 ETIM: EC011860 Facts Cutting diameter: 25 mm Thread: M12 Overall length: 59 mm Number of cutting edges: 4 Special features Compatible inserts: LNMX 0603 Insert manufacturer fit: Korloy Fastening screw: Torx M3x7 Torx key size: T8 FAQ Which indexable inserts fit this cutter? The cutter is specified for LNMX 0603 indexable inserts; compatible grades from Korloy are suitable for the intended clamping arrangement. What is the thread type for mounting? Mounting is via an M12 thread, providing a secure screw-in connection to the toolholder. How many cutting edges does the tool have? The body is designed for 4 cutting edges, offering a balanced cutting action for stable machining. Which screw and key are used to secure the insert? The insert is retained with a Torx M3x7 screw and requires a T8 key for assembly and removal. What is the SKU for ordering spare bodies or replacements? Order or reference the tool as VT154TM when enquiring about the screw-in milling cutter from Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

With a secure M12 mounting and a compact Ø25 mm cutting diameter, this screw-in cutter combines reliable clamping with four cutting edges for steady material removal; order the screw-in cutter VT247TM directly via Metav Werkzeuge or consult the specialists for application advice. Screw-in cutter VT247TM by Teknik Cutting Tools – M12 thread, Ø25 mm, for XNEX 0403 indexable inserts A screw-in cutter VT247TM designed for indexable-insert milling with XNEX 0403 plates, suited to workshop and production use where fast insert changes and stable mounting are required M12 thread for secure mounting Ø25 mm cutting diameter 4 cutting edges for stable machining Compatible with SECO XNEX 0403 inserts Stable mounting and consistent surface quality The screw-in milling head offers a M12 mounting combined with a 22 mm thread height, providing a rigid connection to the toolholder that reduces runout and vibration. This mechanical stability supports consistent surface finish and longer insert life, particularly when machining interrupted cuts or varying material sections. The compact Ø25 mm body and overall length of 52 mm balance accessibility with strength, making the tool suitable for confined set-ups while maintaining the mechanical integrity expected in industrial milling. Such dimensional design directly contributes to repeatable process results and fewer reworks. Productivity through quick insert handling and robust geometry Equipped with 4 cutting edges and a 30 mm cutting height, the design focuses on reducing downtime during servicing and maintaining steady material removal rates. Insert clamping uses a Torx screw M2.5 x 5.5 with a T7 key, enabling reliable retention and straightforward insert replacement with standard workshop tools. The combination of multiple cutting edges and the short, well-balanced overall length minimises vibration at moderate spindle speeds and helps to preserve insert geometry over longer tool life. Where frequent index changes are part of the production rhythm, this configuration supports efficient machining cycles and predictable throughput. Compatibility, handling and workshop integration Intended for XNEX 0403 indexable inserts and compatible with SECO plate systems, the cutter integrates into common insert inventories without requiring bespoke tooling. The lightweight construction (approx. 0.115 kg) aids in handling during tool changes and contributes to lower centrifugal loads at the holder interface. The screw-in concept simplifies replacement and inventory management: the head is a characterised component that can be matched to existing insert grades and machining strategies. For procurement and resupply, Metav Werkzeuge offers centralised sourcing and reliable delivery from its Emmerich facility, ensuring consistent product quality for workshops and production lines. Order the VT247TM screw-in cutter via Metav Werkzeuge for dependable supply and expert application advice—contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific machining tasks Technical data Article number: VT247TM Manufacturer: Teknik Cutting Tools Brand: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Core dimensions Diameter: 25 mm Overall length: 52 mm Thread: M12 Thread height: 22 mm Cutting height: 30 mm Cutting edges: 4 Weight: 0.115 kg Features & compatibility For XNEX 0403 indexable inserts Compatible with SECO inserts Torx screw M2.5 x 5.5 Torx key size T7 Indexable-insert screw-in cutter design FAQ Which indexable inserts fit this cutter? The cutter accepts XNEX 0403 indexable inserts, and compatibility with SECO inserts is indicated for flexible workshop integration. What is the mounting thread and engagement length? The tool uses an M12 thread with a 22 mm thread height for secure, low‑runout clamping. How many cutting edges does the tool provide and what is the cutting height? The tool has 4 cutting edges with a 30 mm cutting height, designed for steady material removal and easy indexing. Which fastener is used for insert clamping? Insert retention is via a Torx screw M2.5 x 5.5, tightened or released with a T7 Torx key for reliable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, secure toolholder that combines 25 mm diameter cutting capacity with internal coolant to keep cycle times low and tool life high; the M12 screw-in connection ensures reliable clamping under heavy loads. Order the screw-in milling cutter directly via Metav Werkzeuge or consult our specialists for application advice. Screw-in milling cutter VT247-1TM for XNEX 0403 indexable inserts – 25 mm, internal coolant (Teknik Makina) A robust screw-in milling cutter designed for XNEX 0403 indexable inserts, offering secure M12 mounting and integrated coolant supply for consistent machining results. 25 mm diameter for versatile pocket milling Internal coolant for improved tool life M12 screw-in connection for secure mounting Compatible with Tungaloy XNEX 0403 inserts Faster cycle times through stable cutting conditions Equipped with internal coolant, this tool directs lubricant and coolant straight to the cutting zone, which reduces thermal load and maintains a consistent cutting edge condition. The concentrated coolant flow supports higher feed rates and longer tool life, delivering measurable productivity gains on repetitive milling operations. By combining a 25 mm tool body with a 4 cutting edges configuration, the system balances material removal and surface quality, making it suitable for serial operations where uptime and repeatability matter. Secure clamping and simple changeover for workshop efficiency The M12 screw-in connection provides a compact, vibration-resistant interface that simplifies tool changes and reduces spindle downtime. The upper thread height of 22 mm ensures a positive mechanical engagement in the holder while the included Torx fixings (T8 key; M2.5×6.5 screw) allow for quick insert replacement. Compatibility with Tungaloy XNEX 0403 indexable inserts permits the use of widely available carbide grades, aiding supply chain resilience and minimising inventory complexity for maintenance departments. Application versatility and predictable results on common materials With a 30 mm cutting height and 52 mm overall length, the cutter is suited to pocketing and light slotting tasks in a range of metals where indexable inserts are preferred. The tool’s geometry and coolant feed are optimised for steady chip evacuation and thermal control, supporting consistent surface finish and dimensional stability. For engineers seeking straightforward integration, the cutter offers a repeatable machining platform that converts insert selection and process parameters into predictable part quality. Workshop integration and service considerations The compact weight of 0.115 kg and standardised M12 interface facilitate stocking and handling across production cells. Replacement inserts are secured with a Torx screw that matches common workshop tooling, streamlining maintenance routines. Documentation should list compatible insert grades and recommended speeds and feeds; when selecting parameters, prioritise moderate entry speeds and incremental increases while monitoring chip form to exploit the cutter’s internal coolant benefits. For tailored process recommendations and reliable supply of the VT247-1TM screw-in milling cutter, contact Metav Werkzeuge in Emmerich directly at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss the optimal insert grades and holder arrangements for specific materials and cycle-time targets. Technical data Article number: VT247-1TM Manufacturer: Teknik Makina Product type: Screw-in milling cutter for indexable inserts Compatible inserts: XNEX 0403 (Tungaloy) Thread: M12 Internal coolant: Yes Diameter: 25 mm Overall length: 52 mm Cutting height: 30 mm Thread height: 22 mm Weight: 0.115 kg Number of cutting edges: 4 Torx key: T8 Torx screw: M2.5×6.5 Integrated coolant supply Screw-in connection for compact toolholders Suitable for indexable carbide inserts Robust design for serial production FAQ What insert type fits this cutter? The cutter accepts XNEX 0403 indexable inserts; it is specified for compatibility with Tungaloy grades and geometries suitable for the VT247-1TM screw-in milling cutter. Is the tool suitable for wet machining? Yes; the VT247-1TM features internal coolant to direct lubricant to the cutting zone, so it is designed for wet machining to enhance tool life and surface finish. Which spindle interface does the cutter require? The cutter uses an M12 screw-in connection, providing a secure and compact mounting suitable for standard M12 toolholders. How many cutting edges are available and what is the cutting height? The tool is fitted with 4 cutting edges and offers a 30 mm cutting height, enabling efficient material removal in pocketing and light slotting tasks. What maintenance tools are needed for insert changes? Insert changes require a Torx T8 key to tighten or loosen the Torx screw (M2.5×6.5) supplied with the VT247-1TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, solid carbide construction and precise compatibility with DCMT 11T3 inserts for reliable boring results and reduced downtime. Order the tool directly via Metav Werkzeuge or ask our consultants for application advice. Teknik Makina Boring Bar SDUC with Coolant, Ø25 mm, Solid Carbide The Boring Bar SDUC with Coolant is a right-hand, internally cooled bar designed for precision boring and turning operations with indexable inserts in CNC lathes and turning centres Internal coolant supply Compatible with DCMT 11T3 inserts Solid carbide construction Ø25 mm diameter, 250 mm overall length Precision and performance for demanding machining Manufactured from solid carbide, this boring bar delivers high rigidity and thermal stability for consistent bore geometry and longer tool life. The integrated internal coolant channel directs cutting fluid precisely to the cutting edge, improving chip evacuation and reducing heat at the cutting zone. With a cutting height of 13 mm and right-hand cutting orientation, the tool is engineered to maintain surface finish and dimensional accuracy during interrupted cuts and extended cycles. The combination of robust material and targeted coolant reduces the frequency of rework and supports higher metal removal rates while keeping vibration low. Compatibility that speeds setup and reduces downtime Designed for DCMT 11T3 indexable inserts, the holder accepts commonly used carbide grades and insert geometries for flexible application across batches. Secure clamping is achieved by the specified Torx T15 fastener and M3.5x8.5 screw, allowing quick insert changes and repeatable seating without specialised fixtures. The ISO designation E20S SDUCR 11 simplifies procurement and replacement planning in production environments. These features together cut fixture time and make routine maintenance straightforward, supporting efficient shift handovers and fast tool changes on multi-shift shop floors. Workshop integration and practical advantages With a nominal diameter of 25 mm, overall length of 250 mm and a shank diameter of 20 mm, the tool fits compact tool holders while providing adequate reach for medium-depth bores. The unit’s weight of 0.95 kg contributes to stable rotation and predictable dynamic behaviour on heavy or small spindles. Right-hand cutting direction is optimised for conventional turning set-ups; the internal coolant reduces reliance on external nozzles and helps avoid chip recutting. For manufacturers seeking a dependable, ready-to-fit boring solution, the combination of material choice, coolant delivery and standardised insert compatibility offers a clear performance and productivity advantage. Contact Metav Werkzeuge for a technical consultation on the Teknik Makina SDUC boring bar with internal coolant — reliable supply from Emmerich and short delivery times. Technical Data Article number: KE34TM Manufacturer: Teknik Makina ISO designation: E20S SDUCR 11 Facts Diameter: 25 mm Overall length: 250 mm Shank diameter: 20 mm Weight: 0.95 kg Cutting height: 13 mm Cutting direction: right Special features Material: Solid carbide Internal coolant: yes For indexable inserts: DCMT 11T3 Torx screw: M3.5x8.5 (T15) FAQ Is the bar suitable for standard DCMT 11T3 inserts? Yes. The Teknik Makina SDUC with Coolant is designed for DCMT 11T3 inserts and accepts common carbide grades for turning and boring operations. How is the coolant supplied to the cutting edge? Coolant is delivered through an internal channel; this internal coolant design focuses fluid flow at the insert edge to improve chip evacuation and cooling. What torque driver is required for insert clamping? Insert clamping and screw access are specified for a Torx T15 key and the screw size is M3.5x8.5, ensuring secure and repeatable clamping. Can this boring bar be used on compact CNC lathes? Yes. With a shank diameter of 20 mm, Ø25 mm body and 250 mm overall length, it fits many compact tool holders while providing sufficient reach for medium-depth bores. What does the ISO code E20S SDUCR 11 indicate? The ISO designation E20S SDUCR 11 identifies the holder’s size, geometry and mounting standard, simplifying matching with existing toolholder systems and spare-part ordering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, high-stability shank cutter offering a 25 mm diameter, 55 mm cutting length and compatibility with ADKT 1505 indexable inserts for reliable, repeatable milling operations; fast insert changes are enabled by an M4x10 Torx clamping screw. Order directly via Metav Werkzeuge or consult our specialists for application-specific advice. S318TM Shank Cutter by Teknik Makina — 25 mm diameter, for ADKT 1505 indexable inserts A S318TM shank cutter engineered for secure mounting of ADKT 1505 indexable inserts, designed to support industrial milling tasks where stability and straightforward insert replacement are essential. 25 mm diameter for stable cutting Compatible with ADKT 1505 inserts (ISCAR) M4x10 Torx clamping with T15 key 200 mm overall length, 55 mm cutting length Consistent cutting performance through robust geometry The cutter’s 25 mm diameter and two cutting edges provide a stable platform that reduces vibration and improves surface quality during interrupted and continuous milling. This geometry supports consistent chip formation and promotes predictable tool life, which is particularly valuable in production environments where repeatability is critical. The tool’s ADKT 1505 compatibility ensures access to a broad range of indexable insert grades, allowing process engineers to select the most appropriate grade for application optimisation. Fast, secure insert changes that save setup time Insert replacement is achieved with a single M4x10 Torx clamping screw using a T15 key, enabling secure tightening and quick service cycles. The simple clamping system reduces downtime during tool changes and minimises the risk of incorrect seating; this translates into higher machine utilisation and lower overall process cost. The 200 mm overall length combined with a 55 mm cutting length balances reach and rigidity for many standard milling set-ups. Designed for workshop efficiency and integration The cutter is compatible with insert geometries from manufacturers such as ISCAR, simplifying procurement and inventory management by allowing the use of widely available ADKT 1505 inserts. With a compact mass of 0.711 kg and moderate overall length, the shank cutter integrates easily into existing toolholders and collet systems. Specified dimensions and standard clamping hardware support straightforward documentation in tooling lists and facilitate rapid selection for CAM programming and fixture planning. Contact Metav Werkzeuge for technical clarification or to request detailed drawings and application guidance for the Teknik Cutting Tools S318TM shank cutter — our Emmerich team is available to advise on insert grades and mounting options. Technical data Article number: S318TM Manufacturer: Teknik Makina Compatible inserts: ADKT 1505 Compatible insert manufacturer: ISCAR Torx screw: M4x10 Torx key: T15 Facts Diameter (mm): 25 Cutting length (mm): 55 Overall length (mm): 200 Cutting edges: 2 Weight (kg): 0.711 Special features For ADKT 1505 indexable inserts Torx clamping for rapid insert change Suitable for standard industrial milling holders FAQ Which inserts fit this shank cutter? The S318TM shank cutter is designed for ADKT 1505 indexable inserts and is compatible with ISCAR ADKT 1505 geometry. What are the key dimensions of the cutter? Key dimensions: 25 mm diameter, 55 mm cutting length, 200 mm overall length; weight approximately 0.711 kg. How is the insert secured? Inserts are secured with an M4x10 Torx screw; a T15 key is required for tightening and removal. Can the cutter be used with different insert grades? Yes, the shank cutter accepts ADKT 1505 inserts in various grades; selecting the correct grade depends on the workpiece material and machining strategy. Is a specific toolholder required? The shank diameter and overall length make the cutter compatible with common milling holders; confirm holder clamping range during tool selection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of robust 25 mm shank rigidity and compatibility with APXT 1003 indexable inserts delivers stable, repeatable milling performance; benefit from a compact overall length and straightforward insert clamping for reduced setup time. Order the product directly via Metav Werkzeuge or ask the consultants if needed. Shaft milling cutter S148TM by Teknik Makina — 25 mm shank, for APXT 1003 indexable inserts Shaft milling cutter S148TM engineered for indexable insert milling in industrial production, designed to accept APXT 1003 inserts for efficient face and shoulder operations 25 mm shank diameter for high rigidity Compatible with APXT 1003 indexable inserts Three cutting edges for consistent material removal 90° cutting angle for accurate shoulder milling Greater stability through compact, rigid design The cutter is built around a 25 mm shank, which provides enhanced rigidity compared with smaller shanks and reduces deflection during interrupted cuts. The result is a more consistent surface finish and extended insert life. With a 100 mm overall length and a 35 mm effective cutting length, the tool minimises overhang while still offering sufficient reach for many commonplace milling tasks. These dimensional choices make the tool suitable for setups where a balance of accessibility and stiffness is required, reducing the need for additional stabilisation or multiple finishing passes. Fast, secure insert clamping reduces downtime Compatibility with APXT 1003 indexable inserts and the use of an M2.5x5.5 Torx screw (Torx key T8) allow for quick insert changes and reliable clamping. The three-edge insert arrangement spreads cutting forces evenly, which improves chip control and lowers the risk of localised insert fracture. Machines benefit from shorter tool-change intervals and predictable cutting behaviour, which supports higher machine utilisation and a smoother production flow. The tool is specified to accept Korloy-manufactured inserts, aligning with common workshop stocking strategies. Practical dimensions and handling for everyday workshop use Key dimensions are chosen for straightforward integration into standard toolholders and adapters. The 25 mm shank diameter pairs with common collet and shrink-fit holders, while the 35 mm cutting length suits many slotting and shoulder operations without excessive tool overhang. At a weight of 0.365 kg, the tool presents modest inertia for controlled acceleration and deceleration on CNC machines. These characteristics simplify clamping checks and balancing procedures and help maintain repeatability across batches, supporting predictable throughput in routine production environments. Application guidance and machining considerations The tool’s 90° cutting angle is intended for square-shoulder and face milling tasks where dimensional accuracy of the shoulder is required. The three cutting edges offer a balance between metal removal rate and surface integrity; selecting suitable feeds and speeds for the workpiece material will determine the achievable tool life and part quality. The design supports standard insert geometries and replacement routines, enabling maintenance teams to manage inventory efficiently. For precise machining parameters, follow the machine and insert manufacturer's guidelines to match cutting data to the workpiece and setup. For specification support or supply of the Teknik Makina S148TM, contact Metav Werkzeuge in Emmerich for tailored advice and order processing: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data Article number: S148TM Brand: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Numbers / Core Technical Data Shank diameter: 25 mm Cutting edges: 3 Overall length: 100 mm Cutting length (effective): 35 mm Weight: 0.365 kg Cutting angle: 90° Special features For APXT 1003 indexable inserts Compatible with Korloy inserts M2.5x5.5 Torx screw for insert clamping Torx key size T8 FAQ Which inserts fit this cutter? The cutter accepts APXT 1003 indexable inserts and is specified for inserts from Korloy compatible with that designation. How many cutting edges does the tool use and why does that matter? The tool uses three cutting edges, which balances metal removal rate and insert strength, promoting even wear and improved chip formation. What are the key dimensions to check for toolholder compatibility? Check the 25 mm shank diameter, 35 mm cutting length, and 100 mm overall length to ensure compatibility with the chosen holder and adequate clearance in the machine setup. What hardware is used to secure the insert? Insert clamping is via an M2.5x5.5 Torx screw, tightened with a T8 Torx key; follow the insert supplier’s tightening guidelines. Is the geometry suitable for square-shoulder milling? Yes—the 90° cutting angle is intended to produce accurate square shoulders and flat faces when correctly applied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid Ø 25 mm shank and precise ENMX 0905 compatibility to achieve reliable chip control and stable machining; order through Metav Werkzeuge or consult our advisors for application-specific selection. Insert milling cutter S934TM — Insert milling cutter body Ø 25 mm for ENMX 0905 by Teknik Makina The Insert milling cutter S934TM is a robust milling tool body engineered for use with ENMX 0905 indexable inserts, providing a compact solution for consistent metal removal in industrial machining. Compatible with ENMX 0905 indexable inserts Ø 25 mm cutter body with 150 mm overall length Two cutting edges for stable material removal Torx M3.5×8.5 clamping with T15 key High rigidity and secure insert clamping for repeatable results The design centres on a Ø 25 mm external diameter and a 25 mm shank, which together increase torsional stiffness and reduce vibration during milling. With a total length of 150 mm, the body balances reach and rigidity, helping to keep tool deflection to a minimum. The clamping is executed via a Torx M3.5×8.5 screw tightened with a T15 key, delivering a consistent seat for ENMX 0905 indexable inserts and supporting predictable tool life. These measurable properties translate into fewer rework cycles and steadier surface quality across batch production. Efficient cutting performance driven by simple, proven geometry Equipped with 2 cutting edges, the cutter body promotes even chip formation and controlled material take‑off, which is particularly useful when alternating between light finishing passes and more aggressive cuts. Compatibility with inserts from YG‑1 ensures access to a wide range of grades and geometries, enabling optimisation of cutting parameters for different workpiece materials. The clear numeric values for diameter, length and edge count make it straightforward to calculate speeds and feeds, supporting faster process set‑up and reduced machine downtime. Practical handling and maintenance for workshop throughput The modular nature of an insert milling cutter body simplifies maintenance: worn inserts are replaced quickly without removing the holder from the spindle, while the Torx clamping system allows standardised torque application and repeatable seating. This reduces tool change time and inventory complexity. The cutter body is suitable for integration into existing tool sets where an Ø 25 mm holder is required, helping to streamline logistics and keep the tool crib concise. The combination of comparably simple maintenance and standard fittings supports reliable shopfloor routines and long‑term production planning. Discuss your application with Metav Werkzeuge to ensure the Teknik Makina insert milling cutter S934TM matches the intended machining strategy and to secure fast supply from our Emmerich hub Technical data Article number: S934TM Manufacturer: Teknik Makina Compatible inserts: ENMX 0905 Suitable insert producer: YG-1 Core dimensions Diameter: 25 mm Shank diameter: 25 mm Overall length: 150 mm Number of cutting edges: 2 Special features Torx screw: M3.5×8.5 Torx key: T15 ECLASS: 21180806 ETIM: EC011860 Description: for ENMX 0905 indexable inserts FAQ Which inserts fit this cutter body? The cutter body accepts ENMX 0905 indexable inserts and is documented as compatible with inserts from YG‑1; the S934TM is specified to seat those insert geometries securely. What are the critical dimensions to check for machine compatibility? Check the Ø 25 mm shank and the 150 mm overall length against spindle and toolchanger clearances; the S934TM requires a 25 mm holder interface. How is the insert secured and which tool is required? Inserts are clamped with a Torx M3.5×8.5 screw using a T15 key, enabling consistent tightening and straightforward insert replacement. How many cutting edges does the tool provide and what is the benefit? The tool body is configured with 2 cutting edges, which helps to balance chip evacuation and cutting force for steady material removal. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust indexable‑insert milling with secure clamping and predictable wall‑finish results; the combination of a 25 mm shank and a 60 mm cutting length ensures rigidity and repeatable machining quality. Order directly via Metav Werkzeuge or consult Metav’s specialists for application guidance and supply. Shank milling cutter S530TM — compatible with R390‑1704 indexable inserts, 25 mm shank (Teknik Makina) The S530TM is a shank milling cutter designed for heavy‑duty and finishing operations with R390‑1704 indexable inserts, offering a square‑shoulder capability and reliable insert retention for production environments 25 mm shank diameter for stable clamping Compatible with R390‑1704 indexable inserts 90° cutting angle for square shoulders Torx M3.5x8.5 clamping screw, T15 key Stable clamping for consistent dimensional accuracy The tool is engineered to deliver a high level of rigidity through its 25 mm shank and precise geometry, reducing vibration during milling. Stable clamping minimises deflection and improves surface finish, which translates directly into fewer rework cycles and higher first‑pass yields. The cutter’s construction supports a 90° cutting angle, making it particularly suitable for producing square shoulders and faces where perpendicularity and planarity are decisive for downstream assembly or measurement. Productivity advantages through insert system and secure fastening By using R390‑1704 indexable inserts, the cutter permits rapid restoration of cutting edges without full tool replacement; the insert system shortens downtime and simplifies tooling logistics. The insert is secured with a Torx M3.5x8.5 screw and requires a T15 key for tightening, providing a reliable clamping interface that resists loosening under typical milling loads. Compatibility with Sandvik‑type inserts broadens tooling options and supports cost‑effective inventory management for production shops. Versatile usage and predictable process integration Configured with two cutting edges and a defined 60 mm cutting length, the cutter balances metal removal and finishing tasks for a range of materials commonly encountered in machining centres. The specified overall length 200 mm and a nominal diameter 25 mm permit use in holders and adaptors where space and reach are constrained. Technical clarity around the cutter’s dimensions allows straightforward integration into CAM setups and tool libraries, enabling accurate cycle‑time estimates and tool‑path validation. Maintainability and system compatibility The tool’s replaceable insert concept reduces lifecycle costs: worn inserts are exchanged quickly while the shank body remains in service. Clear specifications for the clamping screw and key facilitate maintenance procedures and spare‑parts provisioning. Matching the cutter with the correct insert grade and geometry ensures optimised cutting conditions and extended tool life, supporting predictable production planning and consistent part quality. For technical consultation and supply of the Teknik Makina S530TM shank milling cutter with R390‑1704 compatibility, contact Metav Werkzeuge for tailored recommendations and prompt delivery from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S530TM Manufacturer: Teknik Makina Product name (EN): Shank milling cutter for R390 1704 indexable inserts Core technical facts Shank diameter: 25 mm Cutting length (shank): 60 mm Overall length: 200 mm Diameter: 25 mm Number of cutting edges: 2 Cutting angle: 90° Weight: 0.741 kg Clamping screw: M3.5x8.5 Torx key size: T15 Special features and compatibility Compatible inserts: R390‑1704 Suitable for inserts from: Sandvik Insert system: indexable inserts Application: face and shoulder milling Material: tool body materials as specified by manufacturer FAQ Which inserts fit this milling cutter? The S530TM is designed for R390‑1704 indexable inserts; insert compatibility includes Sandvik‑type R390‑1704 grades. What shank diameter and overall length does the cutter have? The shank diameter is 25 mm and the overall length is 200 mm, providing a stable mounting and sufficient reach for many milling tasks. How are the inserts secured in the cutter? Inserts are fastened with a Torx M3.5x8.5 clamping screw; a T15 Torx key is required for correct tightening. For which machining tasks is this cutter intended? The cutter is suitable for face and shoulder milling where a 90° cutting angle is required, balancing metal removal and finishing capabilities. Can the cutter body be reused after insert wear? Yes, the indexable‑insert system is intended for reuse of the cutter body; worn inserts are replaced to restore cutting performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of modular insert technology, a 25 mm shank for increased rigidity and a 70 mm cutting length for extended reach — ideal where uptime and predictable performance matter. Order directly via Metav Werkzeuge or ask the consultants if additional technical details are required. R212TM shank cutter – 25 mm shank, for RDMT 1003 indexable inserts (Teknik Makina) The R212TM shank cutter is a milling tool designed for industrial machining where quick insert changes and consistent cutting performance with RDMT 1003 indexable inserts are required. Compatible with RDMT 1003 indexable inserts Shank diameter 25 mm Two cutting edges for efficient stock removal Total length 200 mm, cutting length 70 mm Consistent productivity through modular insert technology The tool uses proven RDMT 1003 indexable inserts, which keep tooling costs predictable and maintenance simple. Because inserts are replaceable rather than the whole cutter, wear is managed by swapping small, standardised components — a direct saving in both consumable cost and machine downtime. The modular design supports consistent process parameters across batches, enabling stable cycle times and repeatable part quality. Rigidity and reach for stable machining results A 25 mm shank offers higher stiffness in typical milling holders, reducing vibration and improving surface finish on the workpiece. With a 70 mm cutting length and 200 mm overall length, the cutter provides extended reach for deeper pockets or stepped features while maintaining control. The tool’s two cutting edges balance material removal rate and finish, making it suitable for a wide range of conventional milling tasks that demand predictable tool behaviour. Fast insert changes minimise production interruption Insert retention is managed by a M3.5 locking screw and a M3,5x8,5 Torx screw, which are tightened using a T15 key for secure, repeatable fixing. This configuration allows rapid replacement of worn inserts with minimal handling time, so set-up and maintenance intervals become shorter and more efficient. Simple, standardised fastenings also reduce the risk of assembly errors and keep tool change procedures uniform across the workshop. Practical workshop integration and supply reassurance The cutter’s nominal dimensions and weight (listed in the technical data) make it straightforward to fit into existing tool holders and storage routines. At the same time, sourcing via an established supplier provides an operational advantage: confident availability from a European distribution base means fewer supply interruptions and a consistent quality filter for incoming stock. The combination of proven insert geometry and a robust shank helps machine shops maintain throughput without compromising on repeatability. For assured compatibility with RDMT 1003 inserts and the rigidity of a 25 mm shank, contact Metav Werkzeuge for personalised supply and technical advice — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: R212TM Manufacturer: Teknik Makina Facts Shank diameter: 25 mm Cutting length: 70 mm Overall length: 200 mm Cutting edges: 2 Weight: 0.747 kg Special features Compatible inserts: RDMT 1003 Locking screw: M3.5 Torx screw: M3,5x8,5 Torx key size: T15 FAQ Which indexable inserts fit this cutter? The R212TM accepts RDMT 1003 indexable inserts for straightforward insert replacement and consistent cutting geometry. How are inserts secured in the cutter? Inserts are fixed with a M3.5 locking screw and a M3,5x8,5 Torx screw, tightened with a T15 key for repeatable clamping. What are the key dimensions to check for machine compatibility? Key dimensions are a 25 mm shank diameter, 70 mm cutting length and 200 mm overall length; the tool weight is 0.747 kg. How many cutting edges does the tool have? The cutter features two cutting edges, offering a balance between efficient material removal and surface quality. Which tool holders are required? A tool holder or adaptor that accepts a 25 mm shank is required to mount the R212TM securely. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of stable shank interface and quick insert changes for reliable machining cycles; the 25 mm shank and compatibility with RPMW 10T3 indexable inserts ensure repeatable results and straightforward tool maintenance. Order the cutter directly via Metav Werkzeuge or consult our specialists for integration advice. Shank milling cutter R318TM by Teknik Makina — 25 mm shank, for RPMW 10T3 indexable inserts The Shank milling cutter R318TM is a compact indexable milling body designed for versatile face and shoulder milling operations where a secure shank connection and fast insert replacement are essential 25 mm shank diameter for standard holders Compatible with RPMW 10T3 Korloy inserts Two cutting edges for efficient material removal Torx M3.5×8.5 clamping screw, T15 key required Stable connection for consistent machining quality A solid 25 mm shank provides a rigid interface with standard tool holders, reducing runout and vibration during cutting. This rigidity improves surface finish and lowers the risk of premature insert wear, which translates into fewer tool changes and less rework. For production environments that demand steady repeatability, a dependable shank-to-holder fit is a direct advantage to process reliability and uptime. Indexable-insert system that boosts productivity Designed for use with RPMW 10T3 indexable inserts, the tool body enables rapid edge changes without regrinding, offering a clear cost-per-cut benefit over solid cutters. The insert system from Korloy supports simple rotation or replacement of the cutting edge, reducing downtime between operations. This arrangement is especially suitable where quick restorative actions are needed to keep cycles moving and where predictable cutting performance is valued. Secure clamping and straightforward servicing The clamping arrangement uses an M3.5×8.5 Torx screw and requires a T15 key, delivering positive insert retention and effortless servicing on the shop floor. With an overall length of 160 mm and two cutting edges, the design balances accessibility and rigidity for many medium-reach tasks. Maintenance routines are simplified: a single tightening tool and standard replacement inserts allow rapid turnaround during shift changes, supporting continuous operation and easier tool inventory management. Explore the Teknik Makina R318TM with its 25 mm shank — contact Metav Werkzeuge in Emmerich for technical advice, availability and to discuss how this milling cutter can fit into existing tool setups Technical data Article number: R318TM Manufacturer: Teknik Makina Designation: Shank milling cutter for RPMW 10T3 indexable inserts Data Shank diameter (mm): 25 Diameter (mm): 25 Overall length (mm): 160 Cutting edges: 2 Special features Compatible insert: RPMW 10T3 Suitable insert manufacturer: Korloy Clamping screw: M3,5x8,5 (Torx) Torx key: T15 eCl@ss: 21180806 ETIM: EC011860 SKU: R318TM FAQ Which inserts fit this cutter? The R318TM is designed for RPMW 10T3 indexable inserts; the tool body is compatible with Korloy RPMW 10T3 inserts as specified. What is the shank diameter and why does it matter? The shank diameter is 25 mm; a correct shank size ensures a stable connection to the holder and reduces runout for improved cutting accuracy. How is the insert secured in the tool? Insert clamping is achieved with an M3.5×8.5 Torx screw; a T15 key is required for tightening and removal to ensure reliable retention. What operations is this cutter intended for? The milling body is intended for general face and shoulder milling where an indexable system and a standard shank interface are advantageous for productivity and quick insert changes. Can standard workshop tools be used for maintenance? Yes, maintenance requires a standard T15 Torx key for the specified clamping screw, making insert changes straightforward with common workshop tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable milling performance with a 25 mm shank and secure clamping via an M4x7 Torx screw ensure stable, repeatable results. Compatibility with RPMW 1204 indexable inserts provides fast insert changes and a controlled setup. Order or request advice through Metav Werkzeuge for tailored delivery and technical support. Shaft Cutter R325TM — insert milling cutter for RPMW 1204, 25 mm The Shaft Cutter R325TM is an insert milling cutter optimised for stable, repeatable finishing and plunge milling using RPMW 1204 indexable inserts 25 mm shank for high rigidity Compatible with RPMW 1204 inserts M4x7 Torx screw, T15 key 160 mm overall length Maximise setup stability with a solid shank design The combination of a 25 mm shank and a precisely manufactured body improves tool stability during machining, reducing vibration and supporting consistent surface quality. A rigid shank reduces deflection under load, which is particularly important when repeatability and adherence to tight tolerances are required. The milling tool’s 160 mm overall length offers a practical balance between reach and stiffness, making it suitable for operations where a defined working length is necessary without compromising control. These characteristics translate directly into predictable machining behaviour and fewer setup corrections over repeated runs. Fast insert changes and secure clamping for efficient workflows Fast, reliable insert retention is provided by an M4x7 Torx screw that is tightened with a T15 key, enabling secure clamping and straightforward replacement of indexable inserts. Compatibility with RPMW 1204 inserts from recognised manufacturers streamlines stocking and reduces changeover time, since inserts can be swapped without requiring regrinding or rebalancing. The tool’s two cutting edges support economical material removal strategies while keeping spare-part handling simple. Clear mechanical fixing reduces the risk of incorrect seating and helps maintain process stability across shifts. Practical choice for professional workshops and tooling suppliers Designed and supplied by an established tooling brand, this milling cutter supports orderly tool management in workshop environments and trade operations. The straightforward mechanical concept keeps maintenance low and enables fast checks of clamping integrity before production. For procurement and supply chains, the clear compatibility with standard RPMW 1204 inserts and the defined fastening specification simplify purchasing decisions and inventory planning. Documentation of the tool’s core specifications ensures traceability and aids tool-room cataloguing for larger assemblies and fixtures. For supply enquiries or detailed technical advice on the Teknik Makina Shaft Cutter R325TM, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for prompt, specialist assistance. Technical data SKU: R325TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Dimensions & core data Diameter: 25 mm Shank diameter: 25 mm Overall length: 160 mm Cutting edges: 2 Compatibility & fastening Compatible inserts: RPMW 1204 Compatible insert manufacturer: Korloy Torx screw: M4x7 Torx key: T15 FAQ What inserts fit the cutter? The cutter accepts RPMW 1204 indexable inserts; the R325TM is specified for that insert format and is compatible with Korloy RPMW 1204 inserts. How is the insert secured in the tool? Inserts are clamped with an M4x7 Torx screw, tightened using a T15 key, providing a reliable mechanical fixation for repeatable milling. What are the key dimensions to check for fixture compatibility? Verify the 25 mm shank diameter and 160 mm overall length for toolholder and clearance compatibility when integrating the R325TM into a machining setup. How many cutting edges does the tool have and what does that mean for use? The tool has 2 cutting edges, which offers a balance between efficient material removal and straightforward insert management for maintenance and inventory control. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust fastening, compatible indexable inserts and a compact 25 mm shank for reliable milling performance; order this shank milling cutter directly via Metav Werkzeuge or contact our consultants for specification support. S118TM — Indexable insert milling cutter by Teknik Makina, 25 mm shank for TPKN 1103-2204 S118TM is an indexable insert milling cutter designed for efficient slotting and face milling in general machining applications, compatible with TPKN 1103-2204 inserts and engineered for stable, repeatable performance 25 mm shank for secure clamping Compatible with TPKN 1103-2204 inserts 45 mm cutting length for deeper passes Two cutting edges for stable material removal High material removal with predictable performance The S118TM indexable milling cutter is built to deliver consistent chip removal through its two cutting edges, allowing controlled cutting forces and steady tool life. With a 25 mm shank and a total length of 120 mm, the design supports rigid clamping in standard toolholders and reduces deflection during heavier passes. Compatibility with TPKN 1103-2204 indexable inserts simplifies inventory management: triangular inserts offer quick indexing and cost-efficient edge replacement, which translates into lower machining downtime and predictable production throughput. Secure clamping and straightforward tool set-up Clamping is achieved via an M6x14 torx screw; an Allen key size 3 is used to secure the insert seat, which facilitates quick insert changes and reduces maintenance time. The 45 mm cutting length provides sufficient engagement for deeper slotting operations while maintaining balance between reach and stiffness. The cutter’s moderate mass (approximately 0.438 kg) contributes to vibration damping without unnecessary inertia, supporting stable surface quality and extended insert life in routine workshop applications. Designed for workshop reliability and streamlined sourcing This indexable cutter is intended for workshops and small production lines that prioritise flexibility and low lifecycle cost. By accepting widely used TPKN 1103-2204 inserts, the tool enables straightforward repurposing across materials and part geometries when combined with the appropriate insert grade. The compact shank and familiar fixing concept simplify integration into existing tool sets, while the overall construction supports repeatable set-up, reducing inspection cycles and improving throughput. For procurement, Metav Werkzeuge provides fast access and verification from its Emmerich quality hub, ensuring traceable supply for industrial users. Contact Metav Werkzeuge for tailored technical advice and local supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S118TM Manufacturer: Teknik Makina Compatible inserts: TPKN 1103-2204 For inserts: TPKN 1103 Core specifications Diameter: 25 mm Shank diameter: 25 mm Cutting length: 45 mm Overall length: 120 mm Number of cutting edges: 2 Weight: 0.438 kg Design & fixing Torx screw: M6x14 Torx key: 3 Allen Indexable insert type: TPKN 1103 Application: Indexable insert milling cutter FAQ Which inserts fit this cutter? The S118TM accepts TPKN 1103-2204 indexable inserts; the cutter is configured specifically for the TPKN 1103 family to allow quick indexing and economical edge changes. What shank size is required for mounting? The tool features a 25 mm shank, so a toolholder or arbor compatible with a 25 mm shank is required for correct clamping and axial support. How is the insert secured? Inserts are secured with an M6x14 torx screw; an Allen key size 3 is specified for tightening and removal of the screw. What typical operations suit this cutter? This indexable insert milling cutter is suitable for slotting and face milling operations where the 45 mm cutting length and two cutting edges provide controlled material removal and stable surface finish. Is the cutter supplied with inserts? Insert supply is separate; the S118TM is designed to be used with TPKN 1103-2204 inserts that should be selected according to workpiece material and cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a 25 mm shank and secure Torx clamping for stable, vibration-reduced machining combined with the flexibility of VCGT 1604 indexable inserts; the result is efficient tool changes and consistent surface quality — order directly via Metav Werkzeuge or consult our experts for application advice. Shank milling cutter S724TM – 25 mm shank, for VCGT 1604 indexable inserts (Teknik Makina) Shank milling cutter S724TM for modular milling applications, engineered to accept VCGT 1604 indexable inserts for reliable production use across workshop and light industrial settings. 25 mm shank for rigid toolholding Designed for VCGT 1604 indexable inserts Two cutting edges for efficient machining Torx clamping M4x10, T15 specification Stable clamping for consistent surface finish The combination of a 25 mm shank and a substantial 250 mm overall length provides a balance between reach and stiffness, reducing chatter in interrupted or continuous cuts. A robust shank diameter improves toolholder contact and transfer of cutting forces, which in turn helps maintain repeatable accuracy and prolongs tool life. The tool’s mass (approx. 0.92 kg) contributes to damping of vibrations during heavy engagement, resulting in smoother machining and a more reliable surface finish without increasing setup complexity. Modular insert system for fast production cycles Using VCGT 1604 indexable inserts enables quick edge changes and lower tooling costs per cutting edge compared with solid tools. The modular insert approach allows worn edges to be rotated or replaced without removing the entire cutter, minimizing downtime and supporting a higher parts-per-shift output. Secure locating and clamping are achieved with an M4x10 Torx screw (T15), ensuring stable insert retention during high-feed passes and enabling predictable performance in repetitive operations. Designed for practical workshop integration With two cutting edges and a 60 mm cutting length, this milling head is suited to operations where efficient material removal and controlled chip formation are priorities. The design supports straightforward handling during tool setup and insert changeovers, and the clear specification of clamping hardware simplifies maintenance procedures. As a modular milling solution, it fits into established tool systems and can be combined with compatible toolholders and machine set-ups for flexible use in series production or jobbing shops. For modular milling solutions by Teknik Makina and reliable supply from Metav Werkzeuge, contact our team for tailored recommendations and order coordination: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S724TM Manufacturer: Teknik Makina Brand: Teknik Makina Facts Shank diameter: 25 mm Cutting length (shaft): 60 mm Overall length: 250 mm Cutting edges: 2 Weight: 0.92 kg Diameter: 25 mm eClass: 21180806 ETIM: EC011860 Special features Compatible with VCGT 1604 indexable inserts Torx screw: M4x10 Torx key specification: T15 SKU: S724TM Files: 62de7e4fbd24461b3d5f7a29, 62de7ee50f56dbb4de4dbf58 FAQ Which inserts are compatible with this cutter? The cutter accepts VCGT 1604 indexable inserts; the modular system makes insert selection and replacement straightforward. How is the insert secured in the cutter? The insert is clamped with an M4x10 Torx screw; the specified driver size is T15 for secure tightening. What shank diameter is required for the toolholder? A toolholder or arbor suitable for a 25 mm shank is required to ensure correct clamping and rigidity. How many cutting edges does the tool provide? The cutter has two cutting edges, offering a balance between cutting efficiency and chip control. Is the overall length suitable for extended reach operations? With an overall length of 250 mm, the tool provides extended reach while retaining a shank diameter that supports stable machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 25 mm shank, internal coolant and compatibility with XNKU 06T3 indexable inserts, this cutter delivers stable chip control and repeatable results for industrial milling. Order the S780-1TM directly via Metav Werkzeuge or ask our consultants for application support. 25 mm Shank Cutter S780-1TM — 160 mm overall length, internal coolant (Teknik Makina) The 25 mm Shank Cutter S780-1TM is a four‑flute milling cutter designed for heavy-duty machining with XNKU 06T3 indexable inserts, suited to CNC milling tasks in metalworking and toolrooms. 25 mm shank diameter Internal coolant supply Compatible with XNKU 06T3 inserts Four cutting edges for efficient stock removal Rigidity and cutting performance for consistent results The S780-1TM is built around a 25 mm shank and a 160 mm overall length, providing the axial reach required in many workshop and production scenarios while maintaining spindle stability. The four flutes balance material removal rate and surface finish: additional cutting edges allow higher feed per tooth and improve productivity without compromising the workpiece quality. For users less familiar with cutter geometry, more flutes usually mean smoother finishes and higher metal‑removal rates when cutting with suitable feeds and speeds. The robust design supports repeated, reliable passes on standard milling operations. Optimised chip evacuation and tool life through internal cooling Integral internal coolant channels deliver cutting fluid directly to the cutting zone, which reduces edge temperatures and improves chip breaking. This targeted coolant supply helps to extend the life of the XNKU 06T3 indexable inserts and contributes to more consistent dimensional results across batches. In practice, through‑coolant operation reduces the risk of built‑up edge and can enable higher cutting parameters than external coolant alone. The result is improved process stability and fewer unexpected tool changes during long production runs. Compatibility, maintenance and workshop practicality The cutter accepts XNKU 06T3 indexable inserts and is compatible with inserts from Palbit, making replacement and inventory management straightforward where those inserts are already in use. Serviceability is simplified: the head fastening uses a Torx system (Torx key T8) with screw specification M2.5x5.5, allowing secure clamping and quick insert exchange with common workshop tools. The 90 mm cutting length supports deeper engagement when required, while the cutter’s balanced construction keeps vibrations low for improved surface integrity. Produced by Teknik Makina and supplied under SKU S780-1TM, the tool suits manufacturers seeking robust, repeatable performance from a standardised cutting system. Contact Metav Werkzeuge to discuss your application and secure the Teknik Makina S780-1TM with internal coolant from our Emmerich warehouse Technical Data SKU: S780-1TM Manufacturer: Teknik Makina Product type: Shank cutter Key dimensions Shank diameter: 25 mm Overall length: 160 mm Cutting length: 90 mm Number of flutes: 4 Weight: 2.325 kg Special features Internal coolant Compatible with XNKU 06T3 indexable inserts Compatible insert manufacturer: Palbit Torx key: T8 Torx screw: M2.5x5.5 FAQ What insert type does this cutter use? The cutter is designed for XNKU 06T3 indexable inserts and is compatible with inserts from Palbit for straightforward replacement. Does this milling cutter have through‑coolant capability? Yes — the S780-1TM features internal coolant channels to feed cutting fluid directly to the cutting edge for improved tool life and chip evacuation. What shank diameter and overall length are specified? Shank diameter is 25 mm with an overall length of 160 mm, providing a balance of reach and rigidity for many CNC milling setups. How many cutting edges does it have and what are the benefits? The tool has four flutes, which promote efficient stock removal and a smoother surface finish when used with the correct feeds and speeds. Which brand manufactures this cutter and what is the SKU? The cutter is manufactured by Teknik Makina and is stocked under SKU S780-1TM for easy ordering and reference. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of secure clamping, compatibility with LNMX 0603 indexable inserts and a rigid Ø25 mm shank for uninterrupted milling performance — order the Shaft cutter S286TM directly via Metav Werkzeuge or ask our consultants if needed Shaft cutter S286TM – indexable milling cutter, Ø25 mm, 4 cutting edges | Teknik Makina The Shaft cutter S286TM is an indexable milling tool engineered for use with LNMX 0603 inserts, designed for stable face and slot milling in production and workshop environments Ø25 mm cutting diameter Compatible with LNMX 0603 inserts Korloy Four cutting edges for stable milling Shank Ø25 mm, overall length 140 mm Consistent milling performance that reduces downtime As an indexable milling cutter, this tool is built to deliver consistent cutting cycles while keeping maintenance intervals short. Compatibility with LNMX 0603 inserts means changeovers are fast and predictable; worn edges are replaced rather than the entire tool, lowering tooling expenditure and minimising machine downtime. The compatibility with Korloy insert geometries ensures access to a broad range of grades and chipbreakers, allowing process optimisation for different operational demands without altering the cutter body or clamping arrangement. Rigidity and balance for accurate finishes Rigidity is provided by a substantial Ø25 mm shank and a measured overall length of 140 mm, supplying the necessary stiffness for repeatable results across batch runs. The cutter features four cutting edges, which balance material removal rate and surface quality: fewer vibrations, improved tool life for the inserts, and a more consistent component finish. Reduced runout and even load distribution from the robust shank geometry contribute directly to tighter tolerances and lower scrap rates in serial production. Quick, secure insert clamping for operational efficiency Insert changes are secured via an M3x7 Torx screw and driven with a T8 key, allowing straightforward, toolroom-friendly replacement of indexable inserts. The clamping arrangement is engineered to ensure a firm seat for each LNMX 0603 plate, promoting repeatable seating and stable cutting forces. Faster insert swaps and reliable torque specification translate into less machine idle time and simplified workshop routines, particularly in multi-shift or mixed-production environments. Wide applicability with standardised insert systems Designed around the widely used LNMX 0603 insert format, the cutter is suitable for numerous milling tasks where an indexable solution is preferred over solid-end alternatives. The modular approach—cutter body plus standardised inserts—supports quick adaptation to changing job requirements by selecting the appropriate Korloy insert grade for a given material or surface quality target. The S286TM from Teknik Makina therefore provides a practical middle ground between flexibility and process stability for general milling operations Discuss application suitability with Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 and arrange supply of the S286TM from Teknik Makina through our Emmerich hub Technical Data Article number: S286TM Brand / Manufacturer: Teknik Makina SKU: S286TM ECLASS: 21180806 ETIM: EC011860 Facts Diameter: 25 mm Shank diameter (aufnahme): 25 mm Overall length: 140 mm Cutting edges: 4 Special features For LNMX 0603 indexable inserts Compatible with Korloy inserts Torx screw M3x7, Torx key T8 Indexable milling cutter design FAQ What insert format does this cutter accept? The cutter accepts LNMX 0603 indexable inserts; the body is configured for that insert geometry to ensure correct seating and chip formation. Which insert manufacturers are compatible? This tool is compatible with Korloy inserts and with other suppliers following the LNMX 0603 standard; selection of grade depends on the workpiece material and cutting strategy. What are the shank and overall dimensions? The shank diameter is 25 mm and the overall length measures 140 mm, dimensions that favour stiffness and stability in typical milling setups. How are inserts secured to the cutter? Inserts are clamped with an M3x7 Torx screw and tightened using a T8 key, ensuring secure and repeatable clamping for reliable machining. Is the S286TM suitable for high-production environments? Yes, the modular indexable design of the S286TM by Teknik Makina suits repeated production cycles where quick insert changes and predictable performance are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact milling solution that combines stable clamping with direct compatibility with P32 indexable inserts; the robust 25 mm shank and 66 mm cutting length ensure consistent engagement and repeatable set‑ups. Order the tool directly via Metav Werkzeuge or consult the team for application advice. S380TM Shaft cutter — compatible with P32 indexable inserts, 25 mm shank (Teknik Makina) A S380TM shaft cutter designed to accept P32 indexable inserts for reliable milling in standard production and workshop environments 25 mm shank diameter for stable clamping 66 mm cutting length for deeper engagement Compatible with P32 indexable inserts by Walter Consistent performance through proven geometry and insert compatibility The milling arbor is engineered to deliver consistent engagement with replaceable cutting edges, which reduces downtime for tool changes and simplifies inventory management. Fitted for P32 indexable inserts, the holder keeps the insert seat and clamping plane aligned, lowering the risk of misalignment and excessive runout. The combination of a 25 mm shank and a 66 mm cutting length supports stable cutting forces during moderate depth passes, promoting predictable chip formation and contributing to longer tool life for the insert system. Secure fastening and straightforward set-up for repeatable results Clamping is performed via an M6 Torx screw that requires a 3 Allen key, providing a compact but secure connection between insert and body. This fastening solution ensures the insert remains seated under cutting loads and simplifies re‑clamping after index changes. Reduced set‑up complexity leads to faster changeovers and higher machine uptime; where precision matters, the repeatability of the interface between arbor and insert delivers tighter dimensional control than ad‑hoc clamping methods. Versatile integration into machining cells and standard workflows The tool is suitable for milling operations that utilise replaceable inserts and is presented with a standard overall length of 200 mm and a cutter diameter of 25 mm, enabling straightforward integration into tool magazines and holders designed for shank tooling. Compatibility with inserts from recognised suppliers such as Walter helps maintain a predictable supply chain for cutting edges, while the standardised interface supports a range of common machining tasks without the need for bespoke adapters. Reliability, supply and the advantages of indexable tooling Choosing an indexable solution reduces per‑cutting‑edge cost and simplifies maintenance: worn edges are replaced rather than the entire tool body, which lowers life‑cycle expenditure in the long term. The robust construction (weight approx. 0.745 kg) and standardised clamping support high repeatability in serial production. Metav’s distribution from Emmerich provides a practical procurement route and a quality filter for European customers seeking dependable delivery and product conformity. For tailored advice on integrating the S380TM into existing toolsets or to request a quotation via Metav Werkzeuge (Emmerich), contact the Metav team by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: S380TM Manufacturer: Teknik Makina Product: Shaft cutter for P32 indexable inserts Facts Shank diameter: 25 mm Cutting length: 66 mm Total length: 200 mm Diameter: 25 mm Weight: 0.745 kg Special features Compatible inserts: P32 25 Compatible insert manufacturer: Walter Torx screw: M6 Required key: 3 Allen Files (IDs): 62de7e540f56dbb4de4dbf09, 62de7ee7148ec6b71020ffc5 FAQ Which insert type fits this cutter? The cutter accepts P32 indexable inserts; the seat and clamp are configured for the P32 25 style inserts. How is the cutting edge secured? An M6 Torx screw secures the insert; the connection requires a 3 Allen key for tightening and removal. What are the key dimensions to check for toolholder compatibility? Relevant dimensions include the 25 mm shank diameter and a total length of 200 mm, plus a cutting length of 66 mm. Is the cutter compatible with inserts from other manufacturers? The cutter is specified for P32 inserts and is listed as compatible with inserts from Walter; other manufacturers with the same P32 seating geometry may be suitable. What operational benefits does an indexable system provide? Indexable tooling reduces per‑edge cost, speeds up replacement, and maintains consistent cutting geometry across multiple re‑indexings, improving production efficiency and repeatability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of robust compatibility with Sandvik R390-11T3 indexable inserts, a 25 mm shank diameter for improved rigidity, and a secure Torx fastening system for dependable toolholding; order the cutter directly via Metav Werkzeuge or consult our specialists for application guidance. Schaftfräser S592-1TM — Shank cutter for R390-11T3 indexable inserts (Teknik Makina) The Schaftfräser S592-1TM is a shank-mounted milling cutter engineered for use with R390-11T3 indexable inserts, optimised for shoulder milling and general face-milling applications in steel and similar materials. Compatible with Sandvik R390-11T3 inserts 25 mm shank diameter for high rigidity Three cutting edges for consistent removal 90° cutting angle for precise shoulder milling Streamlined tooling through proven insert compatibility The principal advantage of this shank-mounted cutter is its compatibility with R390-11T3 indexable inserts, which allows shops to standardise on a widely used insert family. Using established inserts reduces inventory complexity and enables straightforward regrinding or replacement when wear occurs. The combination of a purpose-built holder and proven cutting bodies supports predictable cycle times and contributes to lower overall tooling cost by simplifying reconditioning and stock control. Rigidity and stability for consistent machining results A 25 mm shank diameter provides notable stiffness at the tool interface, reducing deflection under load and improving dimensional control when machining shoulders or larger steps. The cutter’s 90° cutting angle is suitable for square shoulder operations, delivering clean vertical faces without secondary profiling. The tool’s balanced geometry and mass (approx. 0.446 kg) help maintain spindle behaviour and vibration resistance, supporting repeatable surface finish and tolerance adherence in serial production. Fast, secure insert clamping for reduced downtime Insert retention is achieved with a Torx system using an M2.5x7 screw and a T8 key, offering a positive, low-maintenance clamping method that minimises the risk of loosening in high-speed cycles. This fastening approach shortens changeover time compared with more complex clamping systems and enables safe, repeatable torque application during maintenance. The cutter’s three cutting edges are arranged to ensure uniform engagement, improving chip control and extending insert life under typical industrial cutting parameters. Suitable applications and productivity considerations Designed primarily as a shank-mounted cutter for indexable inserts, this tool is suitable for operations requiring robust shoulder cuts and face milling in workshop and light industrial settings. The configuration with three edges and a 120 mm overall length gives a balance between reach and stiffness; the 45 mm cutting length provides sufficient engagement for stepped machining. When paired with appropriate inserts and cutting data, the system enhances throughput and reduces the frequency of tool changeovers, making it a rational choice for demanding production routines. Contact Metav Werkzeuge for tailored application advice and precise tooling selection — reach our specialists at +49 2822 7131930 or info@metav-werkzeuge.com to discuss suitability for specific machining tasks Technical data Article number: S592-1TM Designation: Shank cutter for R390-11T3 indexable inserts Brand: Teknik Makina Compatible inserts: R390-11T3 Facts Shank diameter: 25 mm Cutting length (shank): 45 mm Overall length: 120 mm Diameter: 25 mm Number of cutting edges: 3 Weight: 0.446 kg Cutting angle: 90° Special features Torx screw: M2.5x7 Torx key size: T8 Suitable for Sandvik R390-11T3 inserts SKU: S592-1TM FAQ Which inserts fit this shank cutter? The cutter accepts R390-11T3 indexable inserts, making it compatible with that Sandvik insert family for shoulder and face milling. What is the shank diameter and why does it matter? The tool has a 25 mm shank diameter, which increases rigidity and reduces deflection for improved dimensional accuracy during machining. How many cutting edges does the cutter have? This shank-mounted cutter features three cutting edges, designed for consistent material removal and balanced cutting forces. What fastening hardware is used for insert clamping? Insert retention uses a Torx M2.5x7 screw operated with a T8 key, providing secure and repeatable clamping. Is this tool suitable for high-speed machining? The cutter is intended for industrial milling operations; compatibility with high-speed regimes depends on insert grade, workpiece material and cutting parameters chosen. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a rigid 25 mm shank and compatibility with WNGX 0403 indexable inserts for reliable, repeatable milling. The 110 mm overall length provides reach while the four cutting edges ensure efficient chip evacuation and stable results. Order the tool directly via Metav Werkzeuge or consult the Metav team for application advice. Milling cutter S945TM – 25 mm shank, for WNGX 0403 indexable inserts (Teknik Makina) The Milling cutter S945TM is a shank-mounted milling tool engineered for indexable-insert machining with WNGX 0403 inserts, offering a balance of rigidity and accessibility for a wide range of workshop milling tasks. 25 mm shank diameter for stable clamping Compatible with WNGX 0403 indexable inserts Four cutting edges for efficient material removal Torx clamping screw M2.5x5.5, key T8 Greater process stability through a rigid shank and optimised geometry The combination of a 25 mm shank and a precisely balanced cutter body reduces vibration and run-out, which directly benefits surface finish and tool life. With four cutting edges, the design provides consistent material removal per revolution and smoother engagement in interrupted cuts. For jobs where cycle time and repeatability matter, this configuration helps to maintain machining tolerances and reduces the need for secondary finishing operations. The result is a measurable contribution to process efficiency and predictable production output. Fast insert changes and secure clamping for uninterrupted productivity Tooling compatibility with WNGX 0403 indexable inserts keeps consumable logistics simple and reduces machine downtime. The clamping system uses a M2.5x5.5 Torx screw operated with a T8 key, allowing quick, toolmaker-friendly insert replacement without complex adjustments. The Torx interface provides positive drive and reliable screw retention, lowering the risk of loosening under heavy cutting forces. Compatibility with common Korloy inserts further streamlines supply chains and makes the cutter straightforward to integrate into existing tooling inventories. Practical workshop fit and low-maintenance operation An 110 mm overall length gives the tool enough reach for many set-ups while retaining rigidity at the cutting zone. The shank-mounted format simplifies toolholding and reduces balancing requirements compared with longer multi-component holders. Routine maintenance is confined to insert replacement and periodic torque checks on the Torx screw, keeping service intervals short. For procurement and supply reliability, Metav Werkzeuge’s Emmerich operations act as a quality filter for the European market, supporting consistent deliveries and technical guidance for workshop integration. Contact Metav Werkzeuge in Emmerich for application-specific advice or to order the Teknik Makina S945TM — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S945TM Name: Milling cutter for WNGX 0403 indexable inserts Manufacturer: Teknik Makina Key dimensions Diameter: 25 mm Shank diameter: 25 mm Overall length: 110 mm Cutting edges: 4 Special features Compatible with WNGX 0403 indexable inserts Suitable for Korloy inserts Torx clamping screw M2.5x5.5, key T8 eClass 21180806, ETIM EC011860 FAQ What insert type is required for this cutter? The cutter uses WNGX 0403 indexable inserts; the S945TM is designed specifically for this insert geometry and accepts common Korloy variants. How is the insert secured in the cutter? Inserts are held with a Torx clamping screw (size M2.5x5.5) tightened with a T8 key to ensure secure seating under cutting forces. What shank size is recommended for toolholders? The tool features a 25 mm shank diameter; holders or collets matched to this diameter are recommended for optimal clamping and run-out control. Is the S945TM suitable for heavy-duty roughing? With four cutting edges and a rigid shank, the tool is suitable for many heavy removal tasks within the limits of the selected insert grade and machine power. Can the cutter be used with inserts from other manufacturers? Compatibility is stated for WNGX 0403 inserts; many manufacturers, including Korloy, offer matching grades and geometries that fit the same seat and clamping style. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid 25 mm shank and a 60 mm cutting length for stable, repeatable machining; combined with compatibility for XOMX 0602‑1204 indexable inserts this tool offers efficient tool changes and reliable surface finishes. Order via Metav Werkzeuge for dependable supply or request advice from our consultants for process integration. Shank cutter S644TM — 25 mm shank, 3 cutting edges, for XOMX 0602‑1204 indexable inserts (Teknik Makina) The Shank cutter S644TM is a robust indexable milling tool designed for precise face and shoulder machining in production environments, compatible with XOMX 0602‑1204 indexable inserts. 25 mm shank diameter for rigid clamping 60 mm cutting length for deeper passes Compatible with XOMX 0602‑1204 indexable inserts Torx M3.5×8.5 fixing screw, T10 key Precision and stiffness for consistent component quality With a 25 mm shank and a substantial overall length of 200 mm, this cutter provides the structural stiffness required for repeatable results on medium‑duty milling operations. The combination of a solid shank and an optimised cutting length reduces vibration and uneven tool wear, which supports improved surface finish and longer service intervals. The tool’s mass (approx. 0.779 kg) contributes to a stable running condition, allowing machine settings to be kept consistent and reducing the need for constant compensation during production. Fast indexable system to lower machining costs Designed for XOMX 0602‑1204 inserts (compatible with SECO insert systems), the cutter uses a three‑edge insert layout and a secure Torx M3.5×8.5 fixing screw operated with a T10 key, enabling quick, repeatable insert changes. This indexable approach separates the cutting geometry from the tool body, so worn cutting edges can be replaced rapidly without full tool replacement. The result is reduced downtime, predictable running costs and a clear path to higher productivity in batch production. Easier set‑up and predictable machining behaviour A 90° cutting angle supports square shoulders and accurate step milling, making the tool suitable where perpendicular faces and tight tolerances are required. The three cutting edges are balanced for smooth engagement, which simplifies feed and speed selection and helps protect both spindle and fixture from undue loads. Installation requires only a standard 25 mm holder and the supplied Torx interface, allowing straightforward integration into existing tool magazines and changeover routines without complex adaption. For professional indexable milling with a rigid 25 mm shank, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich — technical consultation and ordering support are available. Technical data SKU: S644TM Manufacturer: Teknik Makina Designation: Shank cutter for XOMX 0602‑1204 indexable inserts Compatible insert manufacturer: SECO Facts Shaft diameter: 25 mm Cutting length: 60 mm Overall length: 200 mm Cutting edges: 3 Weight: 0.779 kg Cutting angle: 90° Special features Torx fixing screw: M3.5×8.5 Torx key size: T10 Suitable for XOMX 0602‑1204 indexable inserts Indexable system for rapid insert changes FAQ Which indexable inserts fit this cutter? The shank cutter S644TM accepts XOMX 0602‑1204 indexable inserts; compatibility with SECO‑type inserts is specified for straightforward sourcing. What are the key dimensions to check for holder compatibility? Check for a 25 mm shank acceptance in the tool holder and a 200 mm overall length; the S644TM requires a holder that secures a 25 mm shank. How are the inserts secured to the cutter? Inserts are clamped with a Torx M3.5×8.5 screw; a T10 key is used for secure and repeatable fastening on the S644TM. How many cutting edges does the tool have and what is the tool angle? The tool is designed with 3 cutting edges and a 90° cutting angle, which is effective for square shoulder milling and controlled material removal. Is the cutter suitable for different materials? Material suitability depends primarily on the selected insert grade; the S644TM provides the rigid interface and geometry for a wide range of applications when combined with the appropriate XOMX insert grades. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com