Take advantage of the combination of HSS cutting material, ISO2 (6H) tolerance and a three-stage tap sequence to produce precise, repeatable metric threads in steel; order directly via Metav Werkzeuge or contact the consultants for application advice. TECWERK hand tap set DIN 352 — M6 x 1 mm, HSS, ISO2 (6H), 3-piece A TECWERK hand tap set M6 x 1 mm designed for creating accurate ISO metric threads in through and blind holes, optimised for workshop and industrial use with steels up to approximately 900 N/mm² High-speed steel (HSS) cutting material ISO metric thread M6 x 1 mm (DIN 13) Tolerance ISO2 (6H) for precise fit Three-stage set: rough, intermediate, finish Precise metric threads with a reliable three-stage sequence The three-tool sequence — rough, intermediate and finishing cutter — enables consistent thread quality and reduces the need for rework. Using a dedicated rougher followed by an intermediate and a finish tap ensures that chip evacuation and cutting forces are controlled, which is particularly important when producing ISO metric threads in steel. The DIN-guided geometry and ISO2 (6H) tolerance mean fittings and fasteners meet international interchangeability standards, supporting predictable assembly and safer joints. Robust HSS construction for demanding materials Made from high-speed steel (HSS), the taps withstand the elevated cutting temperatures and stresses common in manual threading of medium-strength alloys. The set is specified for steels up to approximately 900 N/mm², so the tools are suitable for a wide range of workshop steels. High-speed steel provides a balance between toughness and hardness, giving resistance to wear without becoming unduly brittle; this reduces breakage risk during intermittent hand tapping and supports longer tool life under normal operating conditions. Ready-to-use geometry and clear application scope The taps are manufactured to DIN 352 standards and are right-hand cutting for standard threading operations; the shank diameter of 6 mm is designed for common handheld or machine-driven holders. The combination of DIN-compliant thread form and the meter-standard pitch simplifies process planning for maintenance and production environments. Supplied as a matched set, the tools help streamline workflow by keeping sequence and performance consistent, which lowers setup time and reduces scrap rates in repetitive threading tasks. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating this TECWERK HSS tap set into production processes — phone +49 2822 7131930 or e-mail info@metav-werkzeuge.com Technical Data Article number: 2000867113NW Item designation: Hand tap set DIN 352 M6 x 1 mm HSS ISO2 (6H) 3-piece TECWERK Facts Thread size: M6 x 1 mm Shank diameter: 6 mm Material: HSS Tolerance: ISO2 (6H) Strength range: suitable for steels up to approx. 900 N/mm² Special features Conforms to DIN 352 Right-hand cutting For through and blind holes Set composition: rough, intermediate, finish Metric ISO thread form (DIN 13 Blatt 1) FAQ What materials can be threaded with this set? The TECWERK hand tap set is intended for use in steels up to approximately 900 N/mm²; the HSS construction also permits use in a range of other common workshop metals where HSS is appropriate. Is the set suitable for blind holes? Yes, the geometry and the three-stage sequence are suitable for both through and blind hole threading operations. How does ISO2 (6H) tolerance affect assembly? ISO2 (6H) provides a precise internal thread tolerance that ensures consistent fits with ISO-standard external threads, improving interchangeability and reducing assembly issues. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

High-strength hand tapping for metric ISO threads is delivered by the combination of HSS cutting material and DIN 352 geometry, producing precise M6 x 1 mm threads with ISO2 (6H) tolerance; the shank Ø 6 mm and right-hand cut support straightforward manual operation. Order TECWERK hand taps directly via Metav Werkzeuge or consult the advisors for application-specific selection. TECWERK Hand tap DIN 352 M6 x 1 mm HSS ISO2 (6H) — precision hand tap for metric threads The TECWERK Hand tap DIN 352 M6×1mm is a high-speed steel hand tap designed for producing metric ISO threads by manual tapping in workshop and industrial environments. HSS material for durability DIN 352 geometry for hand tapping ISO2 (6H) tolerance for precise threads Suitable for steels up to ~900 N/mm² Consistent, assembly-ready threads for production The tap geometry conforms to DIN 352 and the metric thread form specified by DIN 13 Blatt 1, delivering repeatable thread quality that reduces rework and assembly issues. With a specified ISO2 (6H) tolerance, the thread fit is engineered for reliable fastener engagement; this rational advantage supports predictable torque values and lowers the risk of cross-threading in serial processes. The clear specification of the thread standard and tolerance makes integration into existing quality procedures straightforward. Robust cutting performance for medium-strength steels Manufactured from HSS, the tool is intended for use in steels up to approximately 900 N/mm², offering a balance between wear resistance and toughness that suits common workshop materials. The right-hand cutting orientation and solid shank with shank Ø 6 mm ensure compatibility with standard tap wrenches and manual holders. The high-speed steel construction provides stable cutting at the controlled feed rates associated with hand tapping, which helps to maintain cutting edge integrity and extend service life. Practical handling that speeds workshop routines The hand tap's compact dimensions and conventional shank diameter simplify changeover and storage, while the standardised geometry enables predictable chip formation and evacuation during manual operation. For maintenance and replenishment strategies, using standard-compliant taps reduces inventory complexity and supports efficient procurement. The tool is positioned for technicians and maintenance teams who require straightforward, dependable performance without complex tooling changes. For accurate metric thread production with TECWERK quality, contact Metav Werkzeuge for application guidance or to place an order; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility and supply options Technical Data Article number: 2000867133NW Description: Hand tap DIN 352 M6 x 1mm HSS ISO2 (6H) TECWERK Packing unit: 1 Core specifications Thread size: M6 x 1 mm Shank diameter: 6 mm Suitable material strength: steels up to approx. 900 N/mm² Tolerance: ISO2 (6H) Features & materials Cutting material: HSS Standard: DIN 352 Thread form reference: DIN 13 Blatt 1 Cutting direction: right-hand FAQ What materials is this tap suitable for? The TECWERK Hand tap DIN 352 M6×1mm is specified for use in steels up to approximately 900 N/mm² and is made from HSS to provide suitable wear resistance for these applications. Does the tap meet recognised standards for metric threads? Yes, the tool follows DIN 352 geometry and the metric thread form referenced in DIN 13 Blatt 1, producing threads to ISO2 (6H) tolerance for standardised fits. What size holder is required for the tap? The shank diameter is 6 mm, so the tap suits standard tap wrenches and manual holders that accept a 6 mm shank; refer to the tap wrench specifications for clamping range. Is this tool suitable for machine tapping? This item is a hand tap designed according to DIN 352 for manual operation; machine tapping applications typically require machine taps with different flute and chamfer designs. How is chip evacuation managed during use? The DIN 352 hand-tap geometry promotes controlled chip formation suitable for manual tapping; consistent spindle speed and reversing strokes aid chip clearance during operation. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of HSS cutting material, DIN 352 standard compliance and a compact 6 mm shank for reliable manual tapping and consistent thread quality; order the tool directly via Metav Werkzeuge or request expert advice from our consultants. Hand tap DIN 352 No.3 M6 x 1 mm HSS ISO2 (6H) – TECWERK Hand tap DIN 352 No.3 M6 x 1 mm HSS ISO2 (6H) for cutting metric internal threads in general workshop and maintenance applications, optimised for steels up to approximately 900 N/mm² Solid HSS for long-lasting performance Metric M6 x 1 mm, DIN 13 compliant ISO2 (6H) tolerance for precise threads Suitable for steels up to approx. 900 N/mm² Accurate threads with recognised standards for interchangeability This tap is manufactured to DIN 352 and forms a metric M6 x 1 mm internal thread to DIN 13 sheet 1 dimensions, which means the resulting thread is compatible with standard fasteners. The specified ISO2 (6H) tolerance ensures a consistent clearance class for general assembly work; that accuracy reduces rework and assures correct mating with bolts and nuts. For purchasers looking for standard-compliant components, this compliance translates into predictable assembly behaviour and simplified inventory management. Robust cutting performance that supports productivity Made from HSS and designed as a right-hand cutting tool, the tap offers a balance of toughness and wear resistance suitable for repeated manual use. The HSS cutting material maintains cutting edge integrity during normal workshop conditions and resists the dulling that can lead to poor thread form. Specified for use in materials up to approx. 900 N/mm², the tool handles common steels encountered in maintenance, prototyping and small-batch production, helping to keep operations efficient and downtimes low. Compact shank and ergonomic handling for controlled tapping The 6 mm shank diameter fits standard tap wrenches and manual holders, enabling safe, controlled hand tapping without specialised equipment. As a hand tap, it is intended for manual operation where torque feedback and careful entry are required; this helps avoid cross-threading and improves thread straightness. The right-hand cutting direction aligns with conventional drilling and tapping workflows, simplifying training and integration into established machining procedures. Practical applications and selection guidance This tapping tool is suited to workshop repairs, fixture manufacturing and light production where metric M6 threads are required. Choose this option when standard-compliant, repeatable threads are needed and when manual tapping is preferred for flexibility or small volumes. If uncertainty remains about material suitability or thread fit, Metav Werkzeuge provides technical guidance and data verification to support correct tool selection and safe use. For workshop-ready supply and tailored technical advice on compatibility and application, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 to place an order or discuss specifications Technical data Article number: 2000867173NW UID: 2000867173NW Item label: Handgewindebohrer DIN 352 Nr.3 M6x1mm HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 Data Thread size: M6 x 1 mm Shank diameter: 6 mm Tolerance field: ISO2 (6H) Material strength suitability: up to approx. 900 N/mm² Special features HSS cutting material DIN 352 standard (hand tap) Metric ISO thread in accordance with DIN 13 Blatt 1 Right-hand cutting Designed for manual tapping applications FAQ What thread does this tap produce? The tool produces a metric M6 x 1 mm internal thread in accordance with DIN 13 and DIN 352, ensuring compatibility with standard M6 fasteners. Which materials can be machined with this tap? This TECWERK hand tap is suitable for machining common steels and is specified for use in materials up to approx. 900 N/mm² tensile strength. What does ISO2 (6H) tolerance mean for assembly? The ISO2 (6H) tolerance denotes a standard internal thread class that provides reliable clearance and fit for typical bolts and nuts, reducing the risk of interference during assembly. Is this tap suitable for machine tapping? The design follows the hand-tap standard DIN 352 and a 6 mm shank for manual holders; for machine tapping, a machine-specific tap should be selected instead. How should this tap be used to achieve best results? Use appropriate cutting fluid for the material, ensure correct alignment in a tap wrench, and clear chips frequently; the HSS material and right-hand cutting geometry support controlled manual operation. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a compact combination of HSS cutting performance and ISO2 (6H) accuracy to produce reliable M8 threads in both through and blind holes; order directly via Metav Werkzeuge or contact the advisers for application support. Hand tap set M8 × 1.25 mm (HSS, ISO2, DIN 352) — TECWERK metric hand taps for steel Hand tap set M8 × 1.25 mm (HSS, ISO2, DIN 352) for general workshop and industrial thread production, suitable for through and blind holes in medium-strength steels HSS material for durable cutting performance Metric ISO thread M8 × 1.25, DIN 352 standard ISO2 (6H) tolerance for accurate thread fit Set includes taper, intermediate and finishing taps Consistent, standard-compliant threads for assembly reliability The set produces M8 × 1.25 mm metric threads to DIN 352 and ISO2 (6H) tolerance, ensuring repeatable fits with standard fasteners. Compliance with these standards simplifies component matching and inspection, reducing assembly rejects. The ISO2 tolerance is commonly used where precise clearance and engagement are required, so thread quality translates directly into predictable mechanical performance. Durable high-speed steel for workshop environments Manufactured from HSS, the tools balance wear resistance and toughness for machining common construction and engineering steels up to approx. 900 N/mm² tensile strength. The right-hand cutting geometry maintains chip formation suited to manual feeding, while the robust material prolongs service life under typical workshop conditions. This combination reduces the frequency of tap replacement and supports steady productivity on repetitive tasks. Flexible three-stage set for through and blind holes The three-piece composition — taper, intermediate and finishing taps — covers initial lead-in, rough shaping and final sizing, allowing safe machining in both through and blind holes. Starting with the taper tap eases engagement, the intermediate tap refines the thread, and the finishing tap achieves full tolerance and surface finish. The staged approach lowers the risk of breakage and removes the need for specialised tools in many routine threading operations. Easy to mount and integrate with standard tooling A 6 mm shank matches common tap wrenches and holders, enabling quick changeover in manual or bench work. The set is right-hand cutting and intended for conventional tap-handling equipment, which helps integrate the tools into existing workflows without additional adaptors. Clear specification of material and standards facilitates tool selection and process documentation for quality assurance. Contact Metav Werkzeuge for tailored technical advice and to secure the TECWERK HSS M8 × 1.25 tap set — support from Emmerich is available by email or phone Technical data Article number: 2000867115NW Label: Hand tap set M8 × 1.25 mm HSS ISO2 (6H) DIN 352, TECWERK Manufacturer: TECWERK Facts Thread size: M8 × 1.25 mm Shank diameter: 6 mm Set pieces: 3 Material strength suitability: steels up to ~900 N/mm² Tolerance field: ISO2 (6H) Special features Cutting material: HSS Right-hand cutting For through and blind holes Metric ISO thread, DIN 13 sheet 1 compliance Set composition: taper, intermediate, finishing taps FAQ What materials can be machined with this tap set? The TECWERK hand tap set M8 × 1.25 (SKU 2000867115NW) is specified for machining steels up to approximately 900 N/mm² tensile strength and is suitable for standard workshop steels. Is the set suitable for blind holes? Yes, the three-stage configuration (taper, intermediate and finishing taps) is designed for both through and blind hole threading, permitting controlled chip evacuation and reduced breakage risk in blind bores. What tolerance and standards does the set meet? The tools are produced to DIN 352 and provide threads to the ISO2 (6H) tolerance field, ensuring compatibility with commonly used fasteners and assembly standards. What is the shank size and how is the set mounted? Each tap has a 6 mm shank designed to fit standard tap wrenches and holders for manual or bench-mounted work. Does the set include taps for initial and final sizing? Yes, the three-piece set comprises a taper (lead-in), intermediate (second) and finishing (plug) tap to progressively form and size the thread. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the proven combination of HSS cutting material, ISO2 (6H) tolerance and DIN-compliant geometry for accurate, repeatable threads in medium-strength steels; order directly via Metav Werkzeuge or consult the team for application advice. Hand tap DIN 352 No.2 M8x1.25 HSS ISO2 (6H) TECWERK — HSS construction with ISO2 tolerance Hand tap DIN 352 No.2 M8x1.25 HSS ISO2 (6H) TECWERK is a right-hand hand tap designed for cutting metric ISO threads in medium-strength steels and workshop environments HSS construction for durable performance DIN 352 geometry for consistent thread form ISO2 (6H) tolerance for precise mating threads 6 mm shank for standard toolholding Reliable thread accuracy for repeatable assemblies The tap delivers precise M8 x 1.25 threads thanks to the DIN 352 geometry and the ISO2 (6H) tolerance, which together ensure compatibility with standard fasteners and mating parts. This combination reduces rework and thread-fit issues, so assemblies run smoothly and downtime is minimised. The tool’s standard right-hand cutting direction suits conventional tapping procedures, and the specification aligns with DIN 13 Blatt 1, offering engineers and workshop technicians a familiar, verified reference. Robust performance for common workshop steels Manufactured from HSS, the cutting material provides heat resistance and toughness for reliable chip formation when working in steels up to approximately 900 N/mm² tensile strength. The 6 mm shank offers straightforward clamping in manual holders or collets, enabling clean starts and steady cutting action. For users less familiar with material data: HSS stands for high-speed steel, a blend of alloys that keeps the cutting edge under higher temperatures than plain carbon tool steels, which translates to longer lifetime and fewer replacements. Easy integration into existing toolsets and procedures The tool’s metric ISO thread form and standard dimensions mean it slots directly into established workflows without special fixtures. As a hand tap, it requires only conventional tapping technique and common tapping fluid to achieve optimal surface finish and thread integrity. The compact design and industry-standard interface make storage, identification and reordering straightforward — useful for busy shops that value operational clarity and minimal administration. Contact Metav Werkzeuge for tailored advice on TECWERK hand taps and secure fast delivery from Emmerich; technical consultants are available should additional application data be required Technical Data Article number: 2000867155NW Product: Hand tap DIN 352 No.2 M8x1.25 HSS ISO2 (6H) Manufacturer: TECWERK Packing unit: 1 Facts Thread size: M8 x 1.25 Shank diameter: 6 mm Material strength suitability: up to ≈ 900 N/mm² Tolerance: ISO2 (6H) Special features Cutting material: HSS Standard: DIN 352 Thread standard reference: DIN 13 Blatt 1 Right-hand cutting direction Metric ISO thread form FAQ What materials is this tap suitable for? This hand tap is specified for use in steels up to approximately 900 N/mm²; the HSS construction supports clean performance in common workshop steels. Which standards and tolerances does the tap comply with? The tool follows DIN 352 geometry with DIN 13 Blatt 1 thread form and an ISO2 (6H) tolerance for standard metric thread fits. What is the shank diameter and how is it clamped? The shank diameter is 6 mm, intended for standard tap holders, collets or manual holders commonly used in workshop practice. Is this product suitable for machine tapping or manual use? Designed as a hand tap, it is optimised for manual tapping but can be used in appropriate holders where machine feed and torque are controlled to match a hand-tap profile. How is the thread size designated on the item? The designation is M8 x 1.25, which indicates an M8 nominal diameter with a 1.25 mm thread pitch. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combining HSS construction, DIN 352 geometry and an ISO2 (6H) tolerance, this M8 x 1.25 mm hand tap offers dependable metric threads in steels up to approximately 900 N/mm²; order directly via Metav Werkzeuge or contact our consultants for application advice. Hand tap DIN 352 No.3 M8 x 1.25 mm HSS ISO2 (6H) — TECWERK Hand tap DIN 352 No.3 M8 x 1.25 mm HSS ISO2 (6H) for cutting right‑hand metric threads in medium‑strength steels and standard industrial applications HSS cutting tool DIN 352 geometry for reliable chips ISO2 (6H) tolerance class Shank Ø 6 mm for firm clamping Consistent, standardised metric threads for production use The Hand tap DIN 352 No.3 M8 x 1.25 mm HSS ISO2 (6H) is manufactured to recognised industrial standards to produce repeatable metric threads. The combination of DIN 352 geometry and ISO2 (6H) tolerance ensures threads meet standardised fits, which reduces rework and improves interchangeability in assembly. Explaining briefly, ISO2 (6H) denotes a commonly used internal thread tolerance that balances ease of assembly with required accuracy. Durable cutting performance for common workshop steels Made of HSS, the tool delivers good wear resistance and toughness for routine threading tasks in workshop environments. It is specified for steels up to 900 N/mm², so the tool is suitable for typical construction and engineering steels encountered in maintenance and production. The right‑hand cut design and robust blank reduce the risk of premature breakage, translating into fewer tool changes and more consistent throughput on the shop floor. Practical handling and secure clamping for safe operation A shank Ø 6 mm provides a compact, easily clamped interface for standard tap handles and holders. The tool is optimised for manual threading operations in jigs and fixtures where controlled torque and tactile feedback are required. Using a hand tap with standard metric ISO thread geometry simplifies process planning and ensures compatibility with existing gauges and nuts, reducing setup times and inspection complexity. Trusted supply and technical backing from Metav Sourcing this TECWERK hand tap via Metav Werkzeuge combines proven tool quality with a reliable European supply chain. Metav’s approach to democratising precision and its Emmerich‑based quality filtering means consistent availability and clear product provenance. For workshops and technical buyers looking to standardise tooling across multiple workplaces, this tap integrates with common production routines and inspection practices without compromise. Contact Metav Werkzeuge for tailored advice on application and availability — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com to discuss the TECWERK hand tap and order direct from our Emmerich warehouse Technical data Article number: 2000867175NW Name: Hand tap DIN 352 No.3 M8 x 1.25 mm HSS ISO2 (6H) TECWERK Facts Thread: M8 x 1.25 mm Shank diameter: 6 mm Suitable for steels up to approx. 900 N/mm² Tolerance: ISO2 (6H) Special features HSS material DIN 352 geometry Right‑hand cutting Metric ISO thread to DIN 13 Blatt 1 Packaging unit: 1 Brand: TECWERK FAQ Is this tap suitable for hardened steels? This hand tap is specified for use in steels up to approximately 900 N/mm²; it is not intended for high‑hardness steels above that strength. What does ISO2 (6H) mean for thread fit? ISO2 (6H) indicates a standard internal thread tolerance class that provides a consistent, medium fit suitable for general engineering applications with reliable interchangeability. Can the tap be used in a machine or only by hand? As a hand tap manufactured to DIN 352, it is primarily designed for manual use; the shank Ø 6 mm allows clamping in standard tap holders where gentle machine control is possible. How is the product supplied and how to identify it? The tool is supplied individually (packaging unit 1) and can be identified by article number 2000867175NW and the product designation Hand tap DIN 352 No.3 M8 x 1.25 mm HSS ISO2 (6H) TECWERK. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combine the HSS construction with the ISO2 (6H) tolerance and right-hand cutting geometry to achieve consistent, precise M8×1 threads in both through and blind holes; order the tap directly via Metav Werkzeuge or consult our specialists for application advice. Hand tap DIN 2181 finishing tap No.2 M8×1 mm HSS ISO2 (6H) – TECWERK The Hand tap DIN 2181 finishing tap No.2 M8×1 mm HSS ISO2 (6H) is a metric fine-thread finishing tap designed for workshop and industrial use, optimised for steels up to approximately 900 N/mm². HSS finishing tap for M8×1 threads ISO2 (6H) tolerance for accurate fits For through and blind holes; right-hand cut Shank diameter 6 mm for compact toolholders Accurate metric fine threads for reliable assemblies The finishing tap delivers consistent M8×1 mm threads in accordance with DIN 13 specifications, with the ISO2 (6H) tolerance ensuring reliable fits where thread precision matters. Made from HSS, the tool maintains cutting geometry under load and extends service life when used within its material limits. The right-hand cutting design supports conventional tapping in standard workshop setups and is suitable for both manual tapping and use with low-speed machines. This results in fewer reworks and more predictable assembly outcomes, which benefits production planning and quality control. Broad application range across common engineering steels Engineered for work in a wide range of ferrous materials, the tool is rated for steels up to around 900 N/mm², making it suitable for many structural and component applications. It is specified for use in both through and blind holes, so planning for thread depth and chip evacuation is straightforward. Because the tap is a finishing type, it is intended to produce the final thread form after roughing operations; this distinction reduces the risk of overcut or improper fit and supports assemblies that demand tight tolerances and consistent clamping behaviour. Design choices that simplify workshop integration The compact 6 mm shank accommodates cramped toolholders and handheld tap wrenches, while the standard-compliant geometry of the tool aligns with common inspection procedures. The combination of DIN 2181 positioning and the finishing flute profile gives controlled chip formation and improved surface finish on the thread flanks. These attributes translate into shorter setup times and reduced need for secondary finishing, supporting steady throughput on small-batch and repair work where agility and precision are both required. Quality assurance and practical handling guidance As a precision cutting tool, correct use prolongs life and performance: adequate lubrication, correct spindle speed for HSS cutting, and appropriate backing for blind holes reduce wear and breakage. The tool’s right-hand cut and HSS composition are optimised for workshop use rather than for high-speed carbide machining; selecting the right feed and applying steady axial guidance are key to achieving the ISO2 (6H) fit repeatedly. For customers seeking assurance in supply and technical guidance, Metav combines broad product availability with specialist advice to match tools to specific production demands. For precise metric fine-thread finishing and tailored application support contact Metav Werkzeuge—technical advice and ordering are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 2000867082NW Label: Handgewindebohrer DIN 2181 Fertigschneider Nr.2 MF8x1mm HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Data Thread: M8×1 mm Tolerance: ISO2 (6H) Shank diameter: 6 mm Material strength suitability: up to approx. 900 N/mm² Standard: DIN 13 / DIN 2181 Special features Cutting material: HSS Metric ISO fine thread (MF) Right-hand cutting For through and blind holes Finishing tap (Fertigschneider) FAQ What material range is suitable for this finishing tap? The TECWERK finishing tap is suitable for common steels up to approximately 900 N/mm², as stated for the M8×1 tool. Is this tap suited for blind-hole tapping? Yes; the tool is specified for both through and blind holes and is designed to manage chip formation accordingly. What tolerance can be expected from the tap? Threads produced conform to ISO2 (6H) tolerance for reliable mating with standard ISO metric components. What is the shank size and how does that affect holder choice? The shank diameter is 6 mm, which permits use in compact toolholders and standard tap handles for handheld or machine-guided tapping. Does the tool require a specific cutting direction or machine setup? The tap has a right-hand cutting geometry and is intended for conventional clockwise tapping; low-speed, controlled feeds and suitable lubrication are recommended. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from precise metric threading thanks to HSS construction, DIN 352 conformity and compatibility with steels up to ~900 N/mm²; these characteristics combine durability, consistent thread quality and straightforward workshop integration. Order directly via Metav Werkzeuge or consult our advisors for technical clarification. Hand Tap DIN 352 No.1 M8×1.25 HSS ISO2 (6H) — TECWERK A Hand Tap DIN 352 No.1 M8×1.25 HSS ISO2 (6H) TECWERK designed for cutting metric ISO threads in medium-strength steels and general workshop applications HSS material for reliable cutting Metric ISO thread M8×1.25, ISO2 (6H) Suitable for steels up to 900 N/mm² Consistent thread quality for assembly reliability The tap is manufactured to DIN 352 and DIN 13 Blatt 1 standards, which ensures predictable thread geometry and compatibility with standard nuts and tapped holes. The ISO2 (6H) tolerance field provides a dependable fit class for many mechanical assemblies; this means the tapped hole will meet common engineering tolerances without bespoke adjustments. Specified as a right-hand cutter, the tool suits conventional drilling and tapping sequences and is intended for manual or machine-guided tapping where controlled feed and rotation are applied. Long-lasting cutting performance with high-speed steel Constructed from high-speed steel (HSS), the tap delivers a balance of toughness and wear resistance for repeated use. HSS retains cutting-edge hardness at elevated temperatures, so the tool preserves geometry during typical workshop tasks. The specification notes a shaft diameter of 6 mm, which supports secure clamping in standard tap holders and hand tools. As a result, the user benefits from a stable tool connection and reduced vibration, contributing to improved surface finish and longer service life. Application range and material suitability explained The tool is rated for use with steels up to approximately 900 N/mm² tensile strength; this rating indicates suitability for common structural and mild alloy steels encountered in maintenance, prototyping and production work. For users less familiar with material specifications: the tensile strength figure is a measure of the metal’s resistance to being pulled apart; a tap suited to 900 N/mm² will perform reliably on a wide range of workshop steels without premature wear. For non-ferrous or more exotic materials, consult technical guidance to confirm suitability. Practical integration into workshop workflows With a standard M8×1.25 thread form and compliance with DIN norms, the tap is straightforward to integrate into existing tool assortments and jigs. The right-hand cutting direction fits typical lathe and drill sequences, and the HSS core allows occasional sharpening or reconditioning where appropriate. For efficient use, recommended practices include secure clamping of the workpiece, appropriate cutting lubricant for steel, and intermittent reversal (back-off) to break chips when hand tapping or using a tapping head. These measures reduce risk of tap breakage and ensure repeatable results. For precise metric tapping backed by TECWERK specifications and Metav’s quality filter, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss suitability or to place an order Technical data Article number: 2000867135NW Item name: Hand Tap DIN 352 No.1 M8×1.25 HSS ISO2 (6H) TECWERK Manufacturer short: TECWERK Packaging unit: 1 Facts Thread: M8×1.25 Tolerance: ISO2 (6H) Shaft diameter: 6 mm Material rating: for steels up to ~900 N/mm² Standards: DIN 352; DIN 13 Blatt 1 Special features Cutting material: HSS (high-speed steel) Right-hand cut (reversible clearing advised) Metric ISO thread form Suitable for general workshop and maintenance tasks FAQ What material is the tap made from? The tap is manufactured from HSS (high-speed steel), providing heat resistance and wear performance suitable for repeated tapping operations. Which thread specification does the tap produce? The tool cuts a metric ISO M8×1.25 thread to ISO2 (6H) tolerance, matching standard metric fasteners and design specifications. Can this tap be used on hardened steels? The tap is specified for steels up to approximately 900 N/mm² tensile strength; for hardened steels or materials beyond this range, alternative tooling or specialist advice is recommended. Is the tool suitable for machine tapping as well as hand use? Yes, the geometry and shaft Ø 6 mm support secure clamping for both manual tapping and machine-assisted tapping with appropriate holders and torque control. Does the product conform to recognised standards? Yes, the tool is produced in accordance with DIN 352 and references DIN 13 Blatt 1 for metric thread form and dimensions. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust combination of HSS cutting material, precise ISO2 (6H) tolerance and suitability for both through and blind holes to secure consistent fine-thread production. Order directly via Metav Werkzeuge or consult the Metav team for application advice and fast delivery. Hand tap set MF12×1 HSS ISO2 (6H) — Hand tap set, TECWERK Hand tap set MF12×1 HSS ISO2 (6H) for cutting metric fine threads in industrial and workshop environments, suitable for through and blind holes in medium-strength steels. HSS for durable cutting Metric fine thread M12×1 ISO2 (6H) Suitable for through and blind holes 9 mm shank for standard holders Reliable fine-thread performance for production needs The Hand tap set MF12×1 HSS ISO2 (6H) is designed to deliver consistent M12×1 threads with the dimensional precision required for assemblies where fit and function cannot be compromised. Manufactured to DIN 2181 and specified to the ISO2 (6H) tolerance class, the tools help ensure repeatable thread form and fit, reducing rework and inspection time. The use of HSS as the cutting material promotes edge retention under typical workshop feeds and speeds, translating into fewer tool changes and improved process efficiency. Built for common workshop materials and versatile use The set is dimensioned and ground for reliable performance in steels up to approximately 900 N/mm² tensile strength, making it suitable for many engineering and maintenance tasks. Its right‑hand cutting geometry and compatibility with both through and blind holes mean that the same tooling can be deployed across different component types without frequent tool swaps. The result is a simplified tooling list and faster cycle times when producing metric fine threads according to DIN 13 standards. Easy integration and dependable handling at the bench A 9 mm shank offers compatibility with standard tap holders and manual tapping fixtures, enabling quick changeover and secure clamping. The pairing of a preliminary and a finishing cutter within the set provides controlled chip evacuation and progressive material engagement, reducing the risk of tap breakage in blind holes and improving surface finish. For workshop environments seeking predictable outcomes, these attributes support steady throughput and lower downtime. Contact Metav Werkzeuge for tailored recommendations and rapid supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for technical advice and order placement. Technical Data Article number: 2000867060NW Brand: TECWERK Standard: DIN 2181 Product designation: Hand tap set MF12×1 HSS ISO2 (6H) Core dimensions / Performance Thread size: M12×1 Tolerance: ISO2 (6H) Shank diameter: 9 mm Cutting material: HSS Recommended max tensile strength: ≈ 900 N/mm² Cutting direction: right‑hand Suitable for: through and blind holes Special features / Applications Metric fine thread (MF) to DIN 13 Set composition: preliminary and finishing tap Designed for general workshop and maintenance use Compatibile with standard tap holders FAQ What thread form and tolerance does this tool produce? The taps produce an M12×1 metric fine thread at ISO2 (6H) tolerance, ensuring accurate fit for standard fastenings and components. Which materials can be machined with this tap set? This TECWERK tap set is intended for machining steels up to about 900 N/mm² tensile strength and is suitable for typical workshop steels. Can the set be used in blind holes as well as through holes? Yes, the design supports both through and blind holes; the combination of preliminary and finishing cutters improves chip control in blind hole applications. What is the shank diameter and compatibility with holders? The tools feature a 9 mm shank diameter, compatible with most standard tap holders and manual tapping fixtures used in workshops. Which standards and specifications apply to this product (SKU 2000867060NW)? The set conforms to DIN 2181 and is specified as metric fine thread to DIN 13, supplied by TECWERK under article number 2000867060NW. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Taking advantage of high-speed steel construction, an ISO2 (6H) tolerance and a 9 mm shank, this finishing tap delivers consistent metric fine threads MF 12×1 in steels up to approximately 900 N/mm² while reducing rework and downtime. Order the TECWERK hand finishing tap directly via Metav Werkzeuge or consult our specialists for application-specific advice. TECWERK Hand finishing tap DIN 2181 No.2 — MF 12×1 HSS ISO2 (6H) A TECWERK hand finishing tap designed for precise metric fine-thread cutting in workshop and industrial applications, suitable for through and blind holes. HSS construction for durable cutting edges MF 12×1 metric fine thread with ISO2 tolerance Suitable for through and blind hole tapping For steels up to ≈900 N/mm² Consistent fine threads with proven materials and tolerance The finishing cutter is made from HSS, which combines wear resistance with toughness to sustain repeated cutting cycles. The tool cuts a MF 12×1 metric fine thread to ISO2 (6H) tolerance, a standard that ensures reliable fit and interchangeability in assembly. The geometry specified by DIN 2181 as a No.2 finishing tap focuses on producing the final thread form with minimal material displacement, reducing the need for subsequent rework. The shank Ø 9 mm facilitates stable clamping in standard tap holders or chucks, supporting steady manual tapping performance. Faster, safer tapping across common ferrous materials Designed for right-hand cutting, this finishing tap is intended for both through and blind holes, improving cycle efficiency when used after an appropriate pilot drill. The tool is rated for steels with tensile strengths up to approximately 900 N/mm², making it suitable for many alloy and carbon steel applications encountered in maintenance, toolmaking and light production. Using a finishing tap with the correct tolerance reduces the likelihood of thread failure in assembly and can shorten inspection times—an outcome that supports smoother production workflows and lower overall processing costs. Practical handling and application guidance for reliable results The finishing tap’s configuration supports conventional hand-tapping workflows and simple machine tapping setups where manual control is required. Although optimised for finishing operations, correct pre-drilling and the use of suitable cutting fluid remain essential to extend tool life and maintain thread quality. The tool’s HSS material and finishing geometry help resist chipping and bluntness during normal use; periodic inspection of the cutting edges will indicate when replacement is necessary to sustain repeatable, high-quality threads. Contact Metav Werkzeuge in Emmerich for tailored advice on selecting the correct TECWERK finishing tap for specific materials and tapping scenarios Technical data Article number: 2000867084NW Description: Hand finishing tap DIN 2181 No.2 MF 12×1 HSS ISO2 (6H) TECWERK Packaging unit: 1 Manufacturer: TECWERK Core data Thread: MF 12×1 mm Pitch: 1 mm Shank diameter: 9 mm Material: HSS Suitable strength: up to approx. 900 N/mm² Tolerance: ISO2 (6H) Special features DIN 2181 finishing tap Right-hand cutting For through and blind holes Cutting material: HSS Intended for metric fine-thread applications FAQ What thread form and size does this tap produce? The tool produces a metric fine thread MF 12×1, finished to ISO2 (6H) tolerance for consistent fit and assembly. Which materials is the tap suitable for? The finishing tap is specified for use in steels with tensile strengths up to roughly 900 N/mm², making it appropriate for many alloy and carbon steel applications. Is the tap suitable for blind holes as well as through holes? Yes, the design covers both through and blind hole tapping when paired with the correct pilot drill and tapping procedure. What does No.2 in DIN 2181 indicate? No.2 denotes the finishing cutter geometry under DIN 2181, intended to create the final thread profile with minimal material deformation and high dimensional accuracy. How should the tap be held and driven? The shank Ø 9 mm enables clamping in common tap holders or chucks for stable manual or low-power machine tapping; correct alignment and controlled feed are essential for optimal results. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of precise metric fine-thread cutting and durable HSS construction for consistent workshop results; combine ISO2 (6H) tolerance and secure 11 mm shank grip for reliable production. Order directly via Metav Werkzeuge or consult the technical team for matching tool holders and process advice. Hand tap DIN 2181 plug tap No.2 MF14 × 1.5 mm HSS, ISO2 (6H) – TECWERK The Hand tap DIN 2181 plug tap No.2 MF14 × 1.5 mm is a high-speed steel hand tap designed for cutting metric fine internal threads in both through and blind holes for general workshop and industrial use. HSS construction for long tool life Metric fine thread MF14 × 1.5 mm, ISO2 (6H) Designed for through and blind holes Shaft Ø 11 mm for secure tool holding High-performance fine-thread cutting for repeatable results The plug tap delivers precise metric fine threads thanks to the ISO2 (6H) tolerance class, which ensures a consistent fit for mating fasteners and threaded assemblies. Manufactured from HSS, the tool offers improved wear resistance compared with standard carbon steel taps, so thread quality remains stable over longer production runs. The geometry is optimised for right-hand cutting and is specified for steels with tensile strengths up to approximately 900 N/mm², enabling dependable use across common engineering materials without frequent tool changes. Secure clamping and compatibility with standard holders With a Shaft Ø 11 mm, this tap is suited to standard collet and chuck systems commonly found in manual tapping fixtures and hand tap wrenches. The plug tap form provides a balanced cutting length for both through and blind holes, reducing the risk of premature tool breakage when compared with full-length threaders. For workshops requiring consistent thread quality, the combination of material, tolerance and shank diameter simplifies integration into existing tooling setups and minimises setup time. Practical handling, care and process advantages The tool’s HSS composition supports regrinding and maintenance, extending service life when appropriate sharpening procedures are applied. Adequate lubrication and correct feed reduce torque peaks and improve surface finish; the tap is therefore suitable for both single-part repairs and small-series production. The compact design and established DIN specification facilitate storage, inventory control and clear reordering within a comprehensive tooling programme, supporting efficient workflows on the shop floor. For reliable fine-thread production choose the TECWERK HSS plug tap and contact Metav Werkzeuge for ordering details or technical guidance – call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 2000867086NW Product name: Hand tap DIN 2181 plug tap No.2 MF14 × 1.5 mm HSS ISO2 (6H) Manufacturer: TECWERK Packaging unit: 1 Facts Thread: MF14 × 1.5 mm Tolerance: ISO2 (6H) Shaft Ø: 11 mm Suitable material strength: up to approx. 900 N/mm² Special features Material: HSS Metric fine thread (MF) Right-hand cutting For through and blind holes Conforms to DIN 13 / DIN 2181 standards FAQ What thread size and pitch does this tap produce? The tap cuts an MF14 × 1.5 mm metric fine thread, specified in the product designation and suitable for fine-pitch assemblies. Is the tap suitable for hardened steels? The tool is specified for steels up to approximately 900 N/mm²; it is not intended for machining highly hardened materials beyond this tensile range. Can the tap be used in a hand tap wrench or machine holder? Yes. The Shaft Ø 11 mm allows secure clamping in standard hand tap wrenches and many common machine collet systems for versatile use. What material is the tap made from and what benefits does that offer? Manufactured from HSS, the tap provides good wear resistance, the option for regrinding, and reliable cutting performance in typical workshop applications. How are through holes and blind holes handled with this tap form? The plug tap geometry is designed to balance cutting engagement for both through and blind holes, reducing the risk of breakage in blind-hole applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of precise ISO2 tolerance, robust HSS cutting material and a 14 mm shank for reliable manual tapping in workshop production. Order the TECWERK finishing tap directly via Metav Werkzeuge or consult Metav’s experts for suitability and supply from Emmerich. TECWERK hand finishing tap MF18x1.5 HSS (ISO2, DIN 2181) TECWERK hand finishing tap MF18x1.5 HSS (ISO2, DIN 2181) is a manually operated finishing tap for metric fine threads, engineered for workshop use and small-batch production HSS high-speed steel construction Metric fine thread MF18x1.5 DIN 13 ISO2 tolerance (6H) for precise fits Suitable for through and blind holes High-precision threads for consistent assemblies The TECWERK hand finishing tap MF18x1.5 HSS delivers accurate metric fine threads thanks to conformity with DIN 2181 and the ISO2 (6H) tolerance class. The finishing geometry removes minimal material to achieve a tight fit, which reduces play in assembled components and improves repeatability. For engineers specifying thread tolerances, the tap’s profile supports predictable mating with standard nuts and threaded holes, lowering the risk of assembly rework. Robust cutting performance in medium-strength steels Constructed from HSS, the tool is suitable for machining steels with strength up to approximately 900 N/mm², offering a balance of hardness and toughness for manual operations. The right-hand cutting design and optimised flute form provide consistent chip formation when used for both through and blind holes, which helps maintain thread quality in intermittent shop use. The material selection and geometry reduce the incidence of premature wear under normal workshop conditions. Workshop compatibility and straightforward handling A 14 mm shank diameter ensures secure clamping in standard tap wrenches and machines adapted for manual tapping, simplifying tooling logistics. The tap’s designation for metric fine thread applications means it integrates well into inventories focused on precision mechanical assemblies. Clear identification of thread size and tolerance supports fast selection during order picking and minimises the chance of incorrect tool use. Cost-efficient choice for precise manual tapping The finishing tap’s focus on thread quality and durability makes it a practical option for production runs where dimensional conformity is critical but full-threading machines are unnecessary. The HSS construction prolongs tool life under correct use, reducing replacement frequency and thus the total cost of ownership for small-batch and maintenance work. For trade partners and contract shops, the tool offers a predictable performance profile that aligns with established machining practices. Choose TECWERK quality for consistent thread performance — contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data SKU: 2000867088NW Label: Hand finishing tap MF18x1.5 HSS (ISO2) TECWERK Manufacturer: TECWERK Facts Thread: MF18x1.5 Tolerance: ISO2 (6H) Shank diameter: 14 mm Material: HSS Suitable for steels up to approx. 900 N/mm² Special features Conforms to DIN 2181 Metric fine thread according to DIN 13 Right-hand cutting For through and blind holes Designed as finishing (Fertigschneider) tap FAQ What thread size and pitch does this tap produce? The TECWERK hand finishing tap creates a metric fine thread of MF18x1.5, corresponding to the labelled pitch and diameter for fine-thread assemblies. Is the tap suitable for blind holes as well as through holes? Yes. The tool is specified for both through and blind holes, with flute geometry chosen to manage chip evacuation in typical workshop conditions. Which materials can be machined with this finishing tap? The finishing tap is made of HSS and is suitable for machining steels with strength up to approximately 900 N/mm²; it is intended for standard workshop applications rather than hardened alloys. What tolerance class does the tap achieve? This finishing tap is manufactured to ISO2 (6H) tolerance, providing the tighter dimensional control required for precision fits. How is the tool identified for ordering and stock? The item is sold as the TECWERK hand finishing tap MF18x1.5 HSS (ISO2) with SKU 2000867088NW, which should be used for accurate ordering and inventory tracking. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Compact, precise and workshop-ready: the TECWERK Hand Tap Set DIN 2181 MF18×1.5 mm combines durable HSS cutting material with an ISO2 (6H) tolerance to deliver reliable metric fine threads in both through and blind holes. Benefit from the two-stage system — roughing and finishing taps — for consistent thread form and reduced rework. Order the hand tap set directly via Metav Werkzeuge or ask our consultants if needed. TECWERK Hand Tap Set DIN 2181 MF18×1.5 mm — HSS, ISO2 (6H), 2-piece A TECWERK Hand Tap Set DIN 2181 MF18×1.5 mm designed to produce precise metric fine threads (MF) in a wide range of workshop steels and to meet DIN 2181 requirements for repeatable accuracy. HSS for long tool life ISO2 (6H) precision tolerance For through and blind holes Two-piece set: rough and finish taps Reliable fine-thread production with measurable accuracy The two-piece set is made from HSS and conforms to DIN 2181, delivering a reproducible thread form for MF18×1.5 mm applications. The tolerance class ISO2 (6H) ensures compatibility with standard mating parts and reduces secondary operations. With a specified capability for steels up to approximately 900 N/mm², the set is suitable for many workshop and light industrial tasks where consistent thread quality and interchangeability are required. The result is a dependable process that improves assembly fit and reduces rejects. Durable construction that eases workshop handling A shaft diameter of 14 mm provides stable clamping in conventional tap handles and reduces wobble during hand tapping. The set contains a roughing (pre‑cut) tap and a finishing tap, which together lower cutting forces and extend life compared with single‑pass tapping. Right‑hand cutting geometry is optimised for common turning directions, while the selection of HSS as the cutting material balances toughness and wear resistance for routine workshop use. These design choices translate into fewer tap breakages and steadier thread production. Clear material and application guidance for confident use Intended for metric fine threads, the set is specified for both through and blind holes; the roughing tap creates the thread form while the finishing tap restores dimensional accuracy and surface quality. The declaration of suitability up to ~900 N/mm² indicates compatibility with medium‑strength alloy and carbon steels commonly encountered in maintenance and fabrication. The ISO2 (6H) tolerance addresses both functional fit and interchangeability, meaning the threads produced will mate reliably with standard fasteners and components. Proven supply chain and workshop support Sourcing this set through an experienced precision partner ensures fast, reliable delivery and access to technical advice when required. Metav Werkzeuge acts as a quality filter for the European market, offering a broad selection of metrology and workshop supplies alongside informed customer service. For operations that value reproducibility and dependable tooling, the combination of DIN conformity, HSS construction and the two‑stage tapping approach provides a pragmatic balance of performance and cost‑effectiveness. Contact Metav Werkzeuge for specific application advice or to request this TECWERK hand tap set MF18×1.5 mm; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000867064NW Item designation: Hand tap set DIN 2181 MF18×1.5 mm HSS ISO2 (6H) 2-piece Manufacturer tag: TECWERK Facts Thread: MF18×1.5 mm Shaft diameter: 14 mm Set: 2-piece (roughing and finishing) Material capability: up to ~900 N/mm² Tolerance: ISO2 (6H) Special features Material: HSS Standard: DIN 2181 Cutting direction: right-hand Suitable for through and blind holes Includes rough and finish tap FAQ What thread size does this set produce? The TECWERK hand tap set produces MF18×1.5 mm metric fine threads and is specified to DIN 2181 for consistent thread form. Which materials can be machined with this set? The set is manufactured from HSS and is suitable for steels up to approximately 900 N/mm², as stated for the TECWERK hand tap set. Does the set contain both roughing and finishing taps? Yes, the two‑piece configuration includes a roughing tap and a finishing tap to improve cutting efficiency and final thread accuracy. Can this set be used for blind holes? The taps are designed for both through and blind holes; use the roughing tap first and complete the thread with the finishing tap for best results. What is the article number or SKU for ordering? The article number is 2000867064NW for the TECWERK hand tap set MF18×1.5 mm. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of precise metric fine-thread production with durable HSS cutting edges and an ISO2 (6H) tolerance for reliable fits; the combination of roughing and finishing taps streamlines workflow and reduces rework. Order directly via Metav Werkzeuge or consult our specialists for application advice. Hand Tap Set DIN 2181 MF24x1.5 HSS ISO2 (6H) — TECWERK, 18 mm shank The Hand Tap Set DIN 2181 MF24x1.5 HSS ISO2 (6H) is a manual tapping solution for producing metric fine threads in steels up to approximately 900 N/mm², suitable for both through and blind holes. HSS for durable cutting performance ISO2 (6H) tolerance for precise thread fits Designed for through and blind holes Accurate metric fine threads with industrial tolerance The two-piece tapping set delivers consistent MF24x1.5 threads thanks to the ISO2 (6H) tolerance class, which ensures a predictable clearance and interchangeability with standard nuts and mating parts. Using a roughing tap followed by a finishing tap reduces material stress and lowers the risk of seized tools, so thread quality is improved and subsequent assembly operations become more reliable. This level of precision supports production processes where thread fit and repeatability are essential. Robust cutting geometry for demanding steels Manufactured from HSS, the taps are engineered to cut into steel grades up to 900 N/mm² with sustained edge life and wear resistance. The set’s right-hand cutting geometry and standard DIN 2181 form provide dependable chip formation and evacuation for typical workshop conditions. The two-step design — a dedicated roughing tool and a finishing tool — balances material removal and surface finish, delivering threads that meet both dimensional and functional expectations without excessive rework. Workshop-ready handling and integration A standard 18 mm shank allows secure mounting in common tap holders and reduces setup time at the bench. The compact format of hand taps makes them suitable for small-batch tasks, maintenance work and toolrooms where flexibility and precision are required. Supplied as a matched pair, the taps simplify process planning: one tool removes the bulk of material, the second ensures the final geometry and tolerance. For buyers seeking consistent supply and technical guidance, Metav’s workshop-oriented approach provides a practical procurement route. For reliable metric fine-thread production with TECWERK’s HSS hand tap set, contact Metav Werkzeuge for individual advice and dependable delivery at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000867067NW Description: Hand tap set DIN 2181 MF24x1.5 HSS ISO2 (6H) 2-piece TECWERK Manufacturer: TECWERK Facts Thread size: MF24 x 1.5 mm Tolerance: ISO2 (6H) Shank diameter: 18 mm Material strength suitability: for steels up to approx. 900 N/mm² Set composition: roughing tap and finishing tap Special features Cutting material: HSS Standard: DIN 2181 Cutting direction: right-hand Suitable for through and blind holes For metric fine-thread applications FAQ What materials can this tapping set machine reliably? The TECWERK hand tap set is specified for use in steels up to approximately 900 N/mm²; the HSS cutting material provides the hardness and toughness required for these applications. How does the two-piece configuration benefit production? Using a roughing tap followed by a finishing tap reduces cutting forces and improves surface quality; the matched pair in the MF24x1.5 set produces consistent threads with the ISO2 (6H) tolerance. Will the 18 mm shank fit standard tap holders? Yes, the 18 mm shank is compatible with common tap handles and holders used in maintenance and small-batch production, enabling quick integration at the bench. Are these taps suitable for both blind and through holes? The set is designed for both through and blind hole tapping; the geometry supports reliable chip removal and thread formation in the typical scenarios described. What distinguishes the ISO2 (6H) tolerance in practice? ISO2 (6H) defines the allowable dimensional deviation for internal threads, providing predictable clearance and interchangeability with standard external threads; this tapping set produces threads to that specification. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund