Take advantage of the combination of HSS cutting performance, ISO2 (6H) tolerance and a practical three-piece progression for reliable thread quality and minimal rework; order the set directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK Hand tap set DIN 352, M2 x 0.4 mm – HSS, ISO2 (6H), 3-piece The TECWERK hand tap set designed for precise metric M2 x 0.4 threads, suitable for through and blind holes in workshop and industrial maintenance. HSS for robust cutting performance Metric ISO thread M2 x 0.4 mm (DIN 352) ISO2 (6H) tolerance for interchangeability Three-piece set: taper, intermediate, finishing Consistent metric threads with industrial tolerances The set delivers accurate metric threads based on DIN 352 and the ISO2 (6H) tolerance band, ensuring reproducible results for small-thread production and repair work. The progressive three-step system—taper, intermediate and finishing cutter—reduces cutting forces at each stage, which leads to clean flank geometry and fewer rejected parts. For production environments where thread interchangeability and assembly reliability matter, this approach minimises rework and secures component fit in serial assemblies and precision fixtures. Material suitability and durability for workshop use Manufactured from HSS, the taps are engineered for durability when machining common workshop alloys; the specification notes suitability for steels up to approx. 900 N/mm², making the set appropriate for many maintenance and fabrication tasks. The 2.8 mm shank provides stable seating in tap wrenches and holders, while the right-hand cutting geometry optimises chip formation during manual tapping. The chosen cutting material and geometry balance wear resistance and edge sharpness so that thread quality is retained over repeated use in day-to-day workshop operations. Workflow efficiency and application flexibility Presented as a compact three-piece set, the tools support an efficient workflow: the taper cutter establishes the thread lead, the intermediate cutter increases thread depth with controlled cutting, and the finishing cutter achieves final tolerance and surface finish. This sequence is particularly beneficial for blind holes where progressive material removal reduces breakout and tool stress. The combination of metric standardisation and practical set design makes the kit well suited to electronics, instrument making and general mechanical repair where small, reliable threads are required. For ordering, technical questions or to discuss suitability for specific materials, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930; Metav’s specialists will advise on the best application and supply options. Technical Data Article number: 2000867108NW Product: Hand tap set DIN 352 M2 x 0.4 mm HSS ISO2 (6H) 3-piece TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867108NW Facts Thread size: M2 x 0.4 mm Standard: DIN 352 Tolerance: ISO2 (6H) Pieces: 3 Shank Ø: 2.8 mm Material strength suitability: steels up to approx. 900 N/mm² Special features Material: HSS Right-hand cutting For through and blind holes Set contains taper, intermediate and finishing cutters FAQ What materials can be machined reliably with this tap set? The TECWERK hand tap set is specified for steels up to approx. 900 N/mm² and is suitable for typical workshop materials used in small-thread applications. What is included in the three-piece set? The set comprises a taper (lead) cutter, an intermediate cutter and a finishing cutter to achieve final thread depth and tolerance. Is the tolerance adequate for interchangeable assemblies? Yes, the ISO2 (6H) tolerance band provides consistent fits for standardised metric assemblies and simplifies component replacement. Can this set be used for blind-hole tapping? The set is designed for both through and blind holes; the progressive cutters reduce breakout and help control chip evacuation in blind threads. Which standard governs the thread form and dimensions? Thread geometry and dimensions are referenced to DIN 352 for small metric hand taps. TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Achieve reliable M2.5 x 0.45 metric threads with a compact three-piece HSS hand tap set that delivers ISO2 (6H) tolerance and is suitable for steels up to 900 N/mm²; order the set directly via Metav Werkzeuge or consult Metav's specialists for technical guidance. TECWERK Hand tap set M2.5 x 0.45 HSS ISO2 (6H) — 3-piece, DIN 352 A hand tap set M2.5 x 0.45 HSS for cutting metric ISO threads in through and blind holes, designed for workshop and maintenance use HSS construction for durability ISO2 (6H) tolerance for precise threads Three taps: taper, intermediate, plug Suitable for steels up to 900 N/mm² Consistent industrial tolerances for secure assemblies The set provides ISO2 (6H) tolerance in accordance with metric standards, which ensures repeatable thread quality and reliable fit for standard screws and bolts. By conforming to recognised norms, the taps reduce rework and rejected assemblies in production or repair tasks. The M2.5 x 0.45 designation is ideal where small, precise metric threads are required; maintaining the correct tolerance class improves load distribution and prevents premature loosening in assemblies. Robust high-speed steel for demanding materials Made from HSS, the tools combine toughness with wear resistance, enabling machining of steels with a tensile strength up to approximately 900 N/mm². The material choice lowers the risk of premature edge wear during repeated hand tapping operations, offering longer service life compared with standard carbon-steel taps. The shank Ø 2.8 mm provides dimensional stability when clamped in a tap wrench, aiding straightness during manual cutting and reducing the chance of breakage. Three-step tapping sequence for reliable results The 3-piece configuration — taper (starter), intermediate and plug (finishing) — divides the cutting forces across stages, which reduces torque on each individual tap and improves chip evacuation in both through and blind holes. This sequence produces a smoother root profile and a cleaner thread form, simplifying assembly and increasing the service life of the fastened joint. For manual tapping tasks, the staged approach is particularly effective in preventing tap fracture and ensuring controlled thread formation. Practical applications and workshop handling Designed in line with DIN 13 Blatt 1 and supplied as a DIN 352 style set, the tools suit general workshop maintenance, small-batch production and precision repair work where metric ISO threads are required. The set is intended for hand operation with a tap wrench and performs well in both through-hole and blind-hole situations. For further clarification on hole preparation or tap selection, Metav Werkzeuge offers technical advice to match the tapping process to the application and material. For accurate M2.5 tapping with dependable ISO2 tolerance, choose the TECWERK HSS 3-piece hand tap set — contact Metav Werkzeuge in Emmerich for ordering or specialist advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000867109NW Description: Hand tap set DIN 352 M2.5 x 0.45 HSS ISO2 (6H) 3-piece TECWERK Manufacturer: TECWERK Facts Thread: M2.5 x 0.45 Tolerance: ISO2 (6H) Material: HSS Shank Ø: 2.8 mm Set composition: 3 pieces Standard: DIN 13 Blatt 1 Special features For through and blind holes For steels up to ca. 900 N/mm² Right-hand cutting Consists of taper, intermediate and plug tap Packaging unit: 1 UID: 2000867109NW FAQ What materials can be machined with this tap set? The TECWERK hand tap set is made from HSS and is suitable for machining steels up to approximately 900 N/mm², as stated in the product description. Is this set suitable for blind holes? Yes, the three-piece configuration is intended for both through and blind holes, improving chip control and reducing the risk of tap breakage in blocked holes. What is included in the 3-piece set? The set comprises a taper (starter) tap, an intermediate tap and a plug (finishing) tap to perform staged thread cutting for reliable results. Does the set meet recognised standards? The tools align with DIN 13 Blatt 1 specifications and are specified as a DIN 352 style hand tap set with ISO2 (6H) tolerance for metric threads. How does the ISO2 (6H) tolerance affect assembly? ISO2 (6H) tolerance provides a consistent clearance and fit for standard metric fasteners, ensuring reliable engagement and reduced risk of loosening or misfit. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a compact tapping solution that combines HSS cutting performance, a tolerance class ISO2 (6H) and suitability for both through and blind holes — a reliable choice for consistent metric M20 x2.5 threads. Order the set directly via Metav Werkzeuge or contact the consultants for application guidance. Hand tap set DIN 352 M20 x2.5 mm HSS ISO2 (6H) – TECWERK The Hand tap set DIN 352 M20 x2.5 mm HSS ISO2 (6H) is a workshop-ready metric tapping set designed for cutting ISO threads in steel components, suitable for both through and blind holes in medium-strength steels HSS material for reliable cutting performance Metric ISO threads to DIN 13, tolerance ISO2 (6H) For through and blind holes in steels up to 900 N/mm² Includes taper, plug and bottoming taps Precision threading for demanding workshop tasks The set delivers consistently accurate M20 x2.5 threads thanks to conformity with DIN 13 and the tight ISO2 (6H) tolerance band, which together ensure interchangeability and reliable assembly in production and maintenance jobs. Manufactured in HSS, the taps retain cutting geometry under repeated use, which reduces rework and supports predictable component fit. For workshops that produce or repair metric-threaded parts, this combination of standards and material provides a clear advantage in repeatable quality and reduced scrap rates. Design and durability that keep production running Each tap is supplied as a sequence of taper, intermediate and finishing cutters—often described as taper, middle and finishing tap—so that threads are formed progressively to minimise chip loads and avoid workpiece damage. The tools are forged with a 16 mm shank for secure clamping and stable hand operation, while the right-hand cutting geometry suits standard threading direction. Rated for steels up to 900 N/mm², the set provides a robust solution for general engineering steels and common workshop alloys, helping to lower downtime and extend tool life through controlled chip evacuation. Easier selection and application for everyday workflows The three-piece arrangement of starter, intermediate and finish taps simplifies process planning: roughing with the taper cutter, intermediate sizing, and finalising with the bottoming tap. This approach reduces the likelihood of tap breakage and improves thread quality in both through and blind holes, even when chip removal is restricted. Clear specification to ISO2 (6H) makes verification straightforward with standard gauges, and the metric designation means the set integrates seamlessly into existing workshop tool assortments without the need for conversions or special fixturing. Contact Metav Werkzeuge for tailored advice and to secure the TECWERK hand tap set with SKU 2000867121NW for immediate delivery from Emmerich Technical data Article number: 2000867121NW Designation: Hand tap set DIN 352 M20 x2.5 mm HSS ISO2 (6H) Manufacturer: TECWERK Packaging unit: 1 Data Thread size: M20 x2.5 Shank diameter: 16 mm Applicable material strength: up to approx. 900 N/mm² Pieces: 3 Special features Cutting material: HSS Standard: DIN 13 sheet 1 Tolerance: ISO2 (6H) Cutting direction: right-hand Application: through holes and blind holes Set composition: taper, middle and finishing taps FAQ What materials are suitable for these taps? The TECWERK hand tap set is specified for steels up to approximately 900 N/mm² and is suitable for common engineering steels as noted in the product data. Does the set include all tap stages for safe thread forming? Yes, the kit contains taper, middle and finishing taps to progress the thread form safely from start to finish and reduce tap stress. Is the tolerance suitable for serial production? The taps are manufactured to ISO2 (6H) tolerance and DIN 13 guidance, making them appropriate where consistent interchangeability is required. Can these taps be used in blind holes? The set is designed for both through and blind holes; using the taper and middle taps first helps manage chip evacuation in blind applications. What is the item number for ordering? The SKU for ordering is 2000867121NW and the product is listed as the TECWERK hand tap set DIN 352 M20 x2.5 mm HSS ISO2 (6H). Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of precision, robust high-speed steel construction and compatibility with ISO metric assembly standards to ensure reliable threadmaking in workshop and industrial settings; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Hand tap DIN 352 No. 3 M20 x 2.5 mm HSS ISO2 (6H) — metric hand tap by TECWERK A Hand tap DIN 352 No. 3 M20 x 2.5 mm HSS ISO2 (6H) TECWERK designed for cutting metric internal threads in steels with a tensile strength of up to approximately 900 N/mm² HSS cutting material for durable performance Metric thread M20 x 2.5 mm to ISO standard Tolerance ISO2 (6H) for consistent fits Consistent thread quality for reliable assemblies The tool is manufactured to DIN 352 and intended specifically for the production of metric internal threads, which ensures repeatable results in serial and single-part work. Made from HSS, the tap maintains cutting geometry under load and is suitable for steels up to 900 N/mm², so the primary benefit is predictable, high-quality threads that reduce the need for rework. The standardised geometry also means compatibility with commonly used fasteners and gauges, supporting efficient assembly processes and predictable part interchangeability. Precision tolerance for assembly accuracy With a tolerance ISO2 (6H), the thread form targets a balance between manufacturing ease and functional clearance. The defined tolerance field minimises variations between mating parts, which directly reduces assembly problems and rejects. The shaft Ø 16 mm provides a secure fit in standard holders and hand tap wrenches, keeping alignment stable during cutting; as a result, thread runout is reduced and component fit is improved. For applications where dimensional conformity and dependable torque transmission matter, this tolerance class is an effective choice. Robust design and practical handling to lower downtime The combination of HSS cutting material and a right-hand cutting geometry yields a tool that is robust in workshop conditions and resists premature wear during typical tapping operations. The tool's design supports manual use as a hand tap while remaining suitable for controlled machine tapping where appropriate. Reduced tool failure and consistent performance mean fewer interruptions to workflow and a lower incidence of damaged workpieces, which together contribute to improved productivity and lower operational costs over time. For reliable metric threading with a TECWERK hand tap, contact Metav Werkzeuge in Emmerich for personalised advice and procurement assistance via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000867181NW Label: Hand tap DIN 352 No. 3 M20 x 2.5 mm HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Thread: M20 x 2.5 mm Shaft diameter: 16 mm Suitable for steels up to: approx. 900 N/mm² Tolerance: ISO2 (6H) Standard: DIN 352 Special features Cutting material: High-speed steel (HSS) Metric ISO thread form (DIN 13 Part 1) Right-hand cutting geometry Designed for manual and controlled machine tapping FAQ What materials is this hand tap suitable for? The TECWERK hand tap is specified for use in steels up to approximately 900 N/mm²; the HSS cutting material provides the necessary wear resistance for these applications. Which thread does the tool produce? This tool produces a metric internal thread of M20 x 2.5 mm, conforming to DIN 13 Part 1 thread form and manufactured to DIN 352 dimensions. What does the ISO2 (6H) tolerance mean for assemblies? The ISO2 (6H) tolerance provides a medium fit range that balances manufacturing ease with reliable mechanical engagement, reducing the risk of assembly mismatch when paired with standard ISO bolts. Will the shaft diameter fit standard tap holders? The shaft Ø 16 mm is intended to fit standard hand tap wrenches and holders designed for 16 mm shanks, offering secure clamping and stable alignment during tapping. Is this product available as a single item or in sets? The article is supplied in the stated packaging unit of 1; for additional quantities or set options, specifications can be checked with Metav Werkzeuge using the SKU 2000867181NW. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

High-speed steel construction and an ISO2 (6H) tolerance deliver durable, accurate threads while the three-stage configuration reduces tap breakage and improves cycle consistency; order the set directly via Metav Werkzeuge or ask the consultants for specification support. Hand tap set M22 x 2.5 mm HSS ISO2 (6H) – 3-piece by TECWERK The Hand tap set M22 x 2.5 mm is a manual three-piece tap set for producing metric ISO threads to DIN standards, suitable for through and blind holes in steels up to 900 N/mm². HSS high-speed steel construction Metric ISO thread to DIN 13 sheet 1 ISO2 (6H) tolerance for precise fits Three-piece set: rough, medium, finish Precision and durability for repeatable threads The Hand tap set M22 x 2.5 mm HSS ISO2 (6H) 3-piece is manufactured from HSS, providing a balance of toughness and wear resistance for robust shop-floor use. The taps meet the DIN 13 metric thread geometry and the ISO2 (6H) tolerance band, which ensures consistent thread fit and interchangeability with standard fasteners. For machinists, this means fewer rejects and more predictable assembly outcomes when working with common engineering steels. The specification for use in steels up to 900 N/mm² gives a clear limit for material selection and helps to prevent premature tool failure in tougher alloys. Faster, safer threading with a three-stage approach A set comprising the rough, intermediate and finish taps reduces cutting forces at each stage and minimises the risk of tap breakage — a frequent cause of downtime in manual tapping operations. The staged process improves chip evacuation and leads to a cleaner flank surface on the finished thread, translating into higher thread quality and less rework. The right-hand cutting geometry suits standard hand-tapping procedures and the defined sequence enhances process reliability, particularly where a mixture of through and blind holes must be handled with the same tooling. Workshop compatibility and practical handling With a shank Ø 18 mm the set fits most standard manual holders and tap wrenches, easing integration into existing workstations without further adaptation. The designation for both through and blind holes clarifies application scope, while the right-hand cut follows conventional machining practice. For maintenance, the HSS material can be re-sharpened in specialised service centres when life is exhausted, extending the economical service life of the set. For selection or workplace integration advice, Metav’s technical team is available to explain fitment and process implications. Understanding standards and avoiding common errors Adherence to metric thread standards reduces assembly issues and simplifies procurement of mating components. The mention of DIN 13 sheet 1 indicates the thread profile and pitch form, while the ISO2 (6H) tolerance denotes a standard internal thread class for general industrial use. When tapping, correct lubrication and the recommended tap sequence should be followed to reduce wear and prevent chipping of the cutting edges. Where material strength approaches the upper limit of 900 N/mm², consider appropriate coolant and conservative feed to maintain tool life. For procurement and technical clarification on the TECWERK three-piece HSS tap set, contact Metav Werkzeuge for availability and application advice at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: 2000867122NW Label: Handgewindebohrersatz DIN 352 M22x2,5mm HSS ISO2 (6H) 3tlg.TECWERK Manufacturer: TECWERK Facts Thread size: M22 x 2.5 mm Shank diameter: 18 mm Set pieces: 3 Suitable tensile strength: up to 900 N/mm² Tolerance: ISO2 (6H) Special features Material: HSS Right-hand cut For through and blind holes Metric ISO thread to DIN 13 sheet 1 Standard: DIN 352 Set includes rough, middle and finish taps FAQ What materials are suitable for these taps? The Hand tap set M22 x 2.5 mm HSS ISO2 (6H) 3-piece by TECWERK is rated for steels up to 900 N/mm² and is optimised for standard engineering steels within that strength range. Is the set suitable for blind holes as well as through holes? Yes. The three-piece configuration is specified for both through and blind holes, enabling controlled chip formation and safer tapping in blind bores. What does ISO2 (6H) mean for thread fit? ISO2 (6H) denotes the internal thread tolerance class that provides a standard medium fit appropriate for general industrial assemblies, ensuring compatibility with common external fasteners. Which standards define the thread geometry of the set? Thread geometry follows the metric specifications referenced as DIN 13 sheet 1, and the taps conform to the DIN 352 designation for hand taps. What is included in the set and how does it improve process reliability? The set contains three taps — rough, intermediate and finish — which together reduce cutting loads, improve chip control and lower the risk of tap fracture compared with single-pass tapping Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a combination of durable HSS construction, ISO2 (6H) tolerance and a standard shaft diameter for reliable manual threading; order the tap directly via Metav Werkzeuge or request specialist advice for application-specific guidance. TECWERK Hand Tap DIN 352 No. 3 – M24 x 3 mm, HSS, ISO2 (6H) A TECWERK Hand Tap DIN 352 No. 3 M24 x 3 mm designed for manual production of metric ISO threads in medium-strength steels and general workshop use High-speed steel (HSS) cutting material ISO2 (6H) tolerance for accurate fits Suitable for steels up to approx. 900 N/mm² DIN 352 geometry with 18 mm shank Consistent cutting performance for routine threading The TECWERK hand tap combines a high-quality HSS cutting material with proven geometry to deliver reliable results in everyday threading tasks. The HSS composition provides a balance of toughness and wear resistance, which means longer service life when used within its recommended application range. With the ISO2 (6H) tolerance, internal threads achieve a predictable fit suitable for mechanical assemblies where standardised clearances are required. This performance-focused design reduces rework and downtime in production and maintenance environments. Practical compatibility for workshop tools and holders Machining set-up is simplified by the standard shaft Ø 18 mm, which allows the tool to be held securely in common tap wrenches and adaptors. The M24 x 3 mm metric pitch corresponds to DIN 13 Blatt 1, making the tap directly compatible with standardised metric systems. The right-hand cutting direction follows conventional thread orientation, so the tool integrates with existing processes without special tooling changes. These compatibility features support quick changeovers and predictable results in mixed-tool workshops. Why the technical choices matter for everyday use Choosing HSS over softer materials ensures the tap withstands intermittent shock loads and resists chipping during hand operation. The ISO2 tolerance (6H) indicates the internal thread tolerance field and provides guidance on mating fasteners and assembly clearances; this is particularly important when parts are produced in several batches or with different machines. The specification to handle steels up to approximately 900 N/mm² gives a clear limit for application: harder materials or specialised alloys will require different grades or coatings. Understanding these technical parameters avoids misuse and extends tool life. Suitable applications and workshop benefits This tap is aimed at maintenance technicians, metalworkers and small production shops that require dependable manual threading of metric components. Typical uses include retrofitting parts, preparing threaded holes for bolts, and one-off production runs where machine tapping is not practical. The tool’s standardisation and robust material make it a pragmatic choice for those who value predictability: consistent thread quality, straightforward handling and compatibility with common accessories. The result is less scrap, fewer mismatches and a smoother workflow on the shop floor. Contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and availability Technical data Article number: 2000867126NW Manufacturer: TECWERK Packaging unit: 1 Facts Thread: M24 x 3 mm Shank diameter: 18 mm Material: HSS Suitable for steels up to approx. 900 N/mm² Special features Standard: DIN 352 Thread standard: DIN 13 Blatt 1 Tolerance field: ISO2 (6H) Cutting direction: right-hand Intended use: metric ISO threads, manual tapping FAQ What materials can this tap be used with? The tap is made of HSS and is specified for use with steels up to approximately 900 N/mm²; the TECWERK Hand Tap DIN 352 No. 3 M24 x 3 mm is therefore suitable for common carbon and alloy steels within that strength range. What does ISO2 (6H) mean for my assembly? ISO2 (6H) denotes the internal thread tolerance class; it ensures a standardised fit for mating bolts and fasteners, giving predictable clearance and interchangeability when using the TECWERK tap (SKU 2000867126NW). How should the tap be held for manual threading? Use a compatible tap wrench or holder that accepts an 18 mm shank; the standard shaft Ø 18 mm matches common workshop holders to provide stable manual operation. Is this tap suitable for machine tapping? The tool follows DIN 352 geometry for hand taps; while primarily intended for manual use, compatibility with machine use depends on the machine’s gripping system and operational parameters — consult Metav Werkzeuge for specifics. How to extend the service life of the tap? Correct cutting lubricant, moderate feed and avoiding materials harder than the specified limit will reduce wear; the HSS composition already offers a resilient starting point for longer life in appropriate applications. TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a high-performance HSS cutting geometry combined with a precise ISO2 (6H) tolerance to achieve reliable, repeatable M24×3 threads in medium-strength steels; the robust 18 mm shank ensures secure clamping in standard toolholders. Order directly via Metav Werkzeuge or consult the Metav team for specification support. TECWERK Hand tap DIN 352 No.2 – M24×3 HSS, ISO2 (6H) The TECWERK Hand tap DIN 352 No.2 M24×3 HSS ISO2 (6H) is a right-hand metric tap designed for manual and bench use when producing M24×3 threads in steels up to approximately 900 N/mm² High-speed steel cutting material ISO2 tolerance for standard fits Suitable for steels up to ~900 N/mm² 18 mm shank for secure clamping Precision threading that reduces rework The tap’s HSS composition and conformant geometry allow for consistent chip formation and wear resistance, which translates into fewer broken tools and less rework. Compliance with DIN 352 ensures the tool’s profile and flute design match established industry practice; together with the ISO2 (6H) tolerance this results in repeatable thread accuracy suitable for assembly with standard ISO nuts and bolts. The result is a measurable reduction in scrap and assembly adjustments when compared with non-standard cutting tools. Reliable performance in common workshop steels Designed to cut metric threads in steels with tensile strengths up to approximately 900 N/mm², the tap offers a compromise between durability and ease of use for bench and manual operations. The right-hand cutting direction and optimised flute form support controlled chip evacuation during manual tapping, reducing the risk of clogging in through-holes and improving the finish of the internal thread. For workplaces that require predictable, robust threading under manual conditions, this tool provides a straightforward technical solution. Compatibility and handling benefits A 18 mm shank diameter allows secure mounting in conventional tap holders and three-jaw chucks, improving concentricity and reducing run-out during tapping. The metric M24×3 pitch is common in industrial assemblies, and the ISO2 (6H) tolerance makes the threads suitable for general engineering applications where standardised fits are required. The compact specification and adherence to DIN standards simplify inventory management and ensure interchangeability across multiple machines and fixtures. Practical application guidance When used for manual tapping, ensure correct lubrication and moderate feed to extend tool life; the HSS cutting material tolerates standard cutting fluids and performs well under intermittent manual operation. The tool is ideal for maintenance, prototyping and small-batch production where quality threads are required without dedicating CNC time. For automated or high-volume operations, consider machine taps or specialised coatings, whereas this solid HSS tool is a cost-effective choice for controlled, manual threading tasks. For workshop-ready metric threading choose TECWERK taps available through Metav Werkzeuge — for tailored advice contact Metav Werkzeuge by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000867163NW SKU: 2000867163NW Manufacturer: TECWERK Packaging unit: 1 Facts Thread size: M24×3 Standard: DIN 352 No.2 Tolerance field: ISO2 (6H) Shank diameter: 18 mm Material strength suitability: up to approx. 900 N/mm² Special features Material: HSS Right-hand cutting Metric ISO thread Conforms to DIN 13 sheet 1 FAQ What materials can this tap be used on? The TECWERK hand tap is designed for cutting metric threads in steels up to approximately 900 N/mm²; its HSS composition also provides acceptable performance on various standard workshop steels. Does the tap meet recognised standards for thread form? Yes, the tool is manufactured to DIN 352 and produces threads to ISO2 (6H) tolerance, ensuring compatibility with standard ISO fasteners. How should the tool be clamped for best concentricity? Clamp the tap by its 18 mm shank in a dedicated tap holder or three-jaw chuck to secure concentricity and reduce run-out during manual tapping. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

A robust HSS hand tap that produces DIN‑compliant M24×3 metric ISO threads with ISO2 (6H) tolerance and an 18 mm shank for secure clamping — ideal for steels up to c. 900 N/mm²; order directly via Metav Werkzeuge or consult the technical team for application guidance. Hand tap DIN 352 No.1 M24x3 HSS ISO2 (6H) — TECWERK The Hand tap DIN 352 No.1 M24x3 HSS ISO2 (6H) — TECWERK is a precision hand tap designed for cutting metric ISO threads in medium‑strength steels, meeting DIN 352 and DIN 13 requirements for reliable assembly. HSS cutting material for extended tool life Conforms to DIN 352 and DIN 13 standards Tolerance ISO2 (6H) for precise fits Shank Ø 18 mm for secure clamping Consistent thread quality for dependable assemblies The tool delivers accurate M24×3 threads in accordance with DIN 352 and DIN 13 Blatt 1, ensuring repeatable results across production runs. The specified ISO2 (6H) tolerance provides a close fit suitable for fasteners that require low play and high positional certainty. For purchasers seeking predictable assembly behaviour, the standard conformity reduces rework and secures interchangeability with standard metric fasteners. Durable HSS construction reduces downtime Manufactured from HSS (high‑speed steel), this hand tap offers wear resistance and a balanced toughness that suits intermittent hand tapping and workshop use. The material choice supports machining in steels with tensile strengths up to approximately 900 N/mm², so tool life and process stability are improved compared with unalloyed steels. The right‑hand cutting geometry simplifies manual operation while maintaining efficient chip formation and evacuation. Practical handling and secure clamping for safe use A 18 mm shank diameter provides robust engagement in standard tap wrenches and holders, lowering the risk of slippage during threading. The hand tap format facilitates controlled feed and torque management in confined or delicate assemblies where machine tapping is impractical. By combining a familiar hand tool design with industrial‑grade specifications, the product bridges workshop convenience with professional results. Specification clarity for informed purchasing Clear technical specifications such as thread size, shank diameter and material simplify selection and inventory management. The concise conformity to DIN and ISO standards supports procurement decisions for maintenance shops, toolrooms and production cells that require documented compatibility. In addition, Metav Werkzeuge’s distribution from Emmerich provides a consistent supply channel and access to application advice when required. For reliable threadmaking in steel, order the TECWERK hand tap via Metav Werkzeuge — contact the Metav team for tailored recommendations or supplementary technical data at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867143NW Item: Hand tap DIN 352 No.1 M24x3 HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Thread: M24×3 Shank diameter: 18 mm Tolerance field: ISO2 (6H) Suitable for steels up to c. 900 N/mm² Special features Cutting material: HSS Standard: DIN 352, DIN 13 Blatt 1 Right‑hand cutting Metric ISO thread FAQ Which materials is this tap suitable for? The TECWERK hand tap is specified for use in steels up to approximately 900 N/mm² tensile strength; material suitability is based on the HSS cutting material and the tool geometry. What standards and tolerances does the tool meet? This hand tap conforms to DIN 352 and DIN 13 Blatt 1 and is manufactured to the ISO2 (6H) tolerance field for metric threads. What is the shank diameter and how should it be clamped? The shank diameter is 18 mm, intended for secure clamping in standard tap wrenches or holders that accept this shank size. Is the cutting direction right‑handed or left‑handed? The tool is right‑hand cutting, suitable for conventional clockwise rotation during tapping operations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from precise metric threading, robust HSS construction and a practical three‑step cutting progression that reduces rework and keeps production moving. Order the set directly via Metav Werkzeuge or ask the technical consultants for application advice and availability. TECWERK Hand tap set DIN 352 M24 x 3 mm, HSS, ISO2 (6H) TECWERK Hand tap set DIN 352 M24 x 3 mm for cutting metric ISO threads in workshop and industrial environments, suitable for both through and blind holes HSS high-speed steel construction ISO2 (6H) tolerance for precise fits For through and blind holes 3-piece set: taper, plug and bottoming Consistent thread quality for reliable assemblies The M24 x 3 mm set complies with DIN 352 and produces metric ISO threads within the ISO2 (6H) tolerance band, ensuring dimensionally consistent connections for mechanical assemblies. Built from HSS, the taps provide a balance of toughness and wear resistance that supports repeatable results in series production and repair work. The result is reduced scrap and fewer thread-related failures, which supports efficient shopfloor throughput and predictable maintenance intervals. Progressive cutting action reduces jamming and rework A three‑step sequence—taper, plug and bottoming tap—enables gradual material engagement and controlled chip formation when creating threads in both through holes and blind holes. The staged approach minimises torque peaks during tapping and improves chip evacuation, which in turn lowers the risk of tap breakage. For customers requiring reliable thread bottoms in blind bores, the set’s final cutter completes the profile accurately without overloading the preceding operations. Practical design for workshop handling and setup A solid 20 mm shank accommodates common tap holders and manual T‑handles, providing stable clamping and straightforward changeover. The right‑hand cutting geometry suits standard production practice. Because the tools are manufactured from HSS, they are compatible with conventional cutting fluids and can be resharpened where appropriate, extending service life and offering an economical choice for maintenance departments and tool cabinets. Guidance on safe use and maintenance Correct use of lubrication, controlled spindle speed and straight alignment are essential to exploit the taps’ life and thread quality. Regular inspection and cleaning after use preserves the cutting edges and reduces the risk of damaged threads. For workshops with mixed materials, adherence to the specified tensile limit avoids premature tool wear; for more demanding alloys, consider specialist coated or carbide alternatives available through the same supply channel. Request technical availability and a tailored recommendation from Metav Werkzeuge in Emmerich: contact info@metav-werkzeuge.com or call +49 2822 7131930 for a quote and application advice Technical data Article number: 2000867123NW SKU: 2000867123NW Designation: Hand tap set DIN 352 M24 x 3 mm, HSS, ISO2 (6H), 3-piece Brand: TECWERK Core specifications Thread size: M24 x 3 mm Standard: DIN 352 Tolerance: ISO2 (6H) Material: HSS (high-speed steel) Shank diameter: 20 mm Cutting direction: right-hand Set composition: taper, plug, bottoming Application: through holes and blind holes Suitable for steels up to approx. 900 N/mm² tensile strength DIN 13 sheet 1 reference Features & applications Metric ISO thread production Three-step hand-tapping sequence For workshop and industrial maintenance Suitable for general steel grades up to ~900 N/mm² Compliance with common European thread tolerances Uncoated HSS cutting material FAQ What is included in the set? The set contains three hand taps in taper, plug and bottoming form; this composition is supplied as the TECWERK hand tap set DIN 352 M24 x 3 mm, SKU 2000867123NW. Which materials can be machined with these taps? These taps are suitable for machining a wide range of steels up to approximately 900 N/mm² tensile strength; the HSS cutting material provides durability for general workshop steels. What does ISO2 (6H) tolerance mean for the thread fit? ISO2 (6H) denotes a standard tolerance class delivering a reliable internal thread fit for general mechanical assemblies, offering a balance between assembly ease and retention without the need for bespoke fitment. Are these taps suitable for blind holes? Yes; the three‑piece sequence includes a bottoming tap specifically intended to complete threads in blind holes after the taper and plug taps have created the initial profile. Can the taps be used with standard tap holders? The tools feature a 20 mm shank that fits common tap holders and manual T‑handles used in workshops and maintenance bays. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of precise ISO2 (6H) tolerances and durable HSS construction for reliable thread production; the three-stage design reduces tool stress and improves thread quality, while the 22 mm shank ensures stable handling – order the hand tap set directly via Metav Werkzeuge or consult our specialists for application advice. Hand tap set DIN 352 M27x3 HSS ISO2 (6H) – TECWERK The Hand tap set DIN 352 M27x3 HSS ISO2 (6H) is a three-piece metric tapping set for cutting M27 × 3 threads in steels up to approximately 900 N/mm², suitable for both through and blind holes. HSS cutting material for durable use Metric ISO thread M27 × 3, tolerance ISO2 (6H) Three-piece set: taper, intermediate, finishing For through and blind holes, steels up to 900 N/mm² Consistent industrial threads with ISO2 accuracy The set delivers metric ISO threads to ISO2 (6H) tolerance, complying with DIN 352 and referencing DIN 13 Blatt 1, which together ensure interchangeability and repeatable fit in threaded assemblies. This industrial conformity reduces rework and inspection effort: parts produced with the set can be assembled confidently, since the taps cut threads to internationally recognised tolerances. The right-hand cutting geometry contributes to predictable chip formation and regular torque behaviour during manual tapping. Robust HSS construction for demanding steel applications Constructed from high-speed steel (HSS), the taps are designed for durability and edge stability when machining ferrous materials. The set is specified for steels up to approx. 900 N/mm², which covers a wide range of structural and engineering steels used in workshops and light production. The 22 mm shank provides solid engagement in standard tap wrenches and holders, helping to minimise wobble and uneven loading during use, thereby lowering the risk of breakage and extending service life. Three-stage design for safer, cleaner tapping The three tools—taper (lead), intermediate (plug), and finishing (bottoming)—work in sequence to distribute cutting forces and evacuate chips progressively. The taper tap starts the thread gently, the intermediate tap refines the form, and the finishing tap produces the final thread profile and tolerance. This staged approach is particularly advantageous in blind-hole tapping, where controlled chip removal is essential, and in through-hole tapping, where the progression reduces torque spikes and tool stress. Practical handling, lubrication and tool care For dependable results, use suitable cutting fluid and ensure correct alignment of the tap to the hole axis; manual tapping benefits from steady feed and periodic reverse motion to break chips. The right-hand cutting orientation matches standard machining practice. After use, clean chips from flutes and store the taps in protective sleeves to preserve cutting edges. Regular inspection of the cutting lips and flutes will indicate when regrinding or replacement is due, keeping process quality high and downtime low. Contact Metav Werkzeuge today to discuss the suitability of the TECWERK Hand tap set DIN 352 M27x3 HSS ISO2 (6H) for specific materials and production tasks, or to arrange a tailored supply from our Emmerich warehouse. Technical data Article number: 2000867124NW Description: Hand tap set DIN 352 M27x3 HSS ISO2 (6H) 3-piece Manufacturer: TECWERK Packaging unit: 1 Specifications Thread size: M27 × 3 Tolerance: ISO2 (6H) Material: HSS (high-speed steel) Shank diameter: 22 mm Suitable material strength: up to approx. 900 N/mm² Number of pieces: 3 Features Metric ISO thread according to DIN 13 Blatt 1 Right-hand cutting direction For through and blind holes Three-stage set: taper, intermediate, finishing Shank Ø 22 mm FAQ What thread size does this set cut? The set cuts metric ISO threads of M27 × 3, as specified for the TECWERK hand tap set (SKU 2000867124NW). Is the set suitable for blind holes? Yes, the three-piece configuration is designed for both through and blind holes, with a finishing tap to complete threads in blind applications. Which materials can be machined with these taps? The taps are made from HSS and are specified for steels up to approx. 900 N/mm², covering many common engineering steels. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Combine HSS construction, DIN 352 conformity and an ISO2 (6H) tolerance for reliable, repeatable M3 x 0.5 metric threads; order directly via Metav Werkzeuge or consult the Metav technical team for application-specific advice. Hand tap DIN 352 No.1 M3 x 0.5 HSS, ISO2 (6H) – TECWERK A Hand tap DIN 352 No.1 M3 x 0.5 HSS ISO2 (6H) engineered for precise metric thread cutting in workshop and maintenance environments HSS high-speed steel construction Conforms to DIN 352 standard ISO2 (6H) metric thread tolerance Suitable for steels up to 900 N/mm² Reliable metric threading to industry standards The tap is manufactured to DIN 352 and references DIN 13 Blatt 1, ensuring the produced threads meet established dimensional and form requirements. The ISO2 (6H) tolerance class guarantees interchangeability with standard fasteners and reduces rework, which supports consistent assembly processes. Using a tool produced to these standards simplifies quality control and documentation in regulated production or repair workflows. Durable HSS cutting for tougher steels Made from HSS, the tool offers favourable wear resistance and toughness for manual tapping tasks. It is designed for use in steels up to approximately 900 N/mm², delivering a balance between cutting performance and tool life in common engineering materials. The right-hand cutting geometry ensures conventional operation in hand taps and compatible holders, while the shank Ø 16 mm provides a secure grip in standard tap handles or collets for steady manual feed and accurate alignment. Designed for workshop efficiency and ease of use As a hand tap intended for maintenance, prototyping and small-batch production, this tool requires minimal set-up and integrates readily into existing tooling kits. Single-unit packaging supports targeted replacement and stock management. The combination of standardised thread form, robust cutting material and a common shank diameter makes the product a practical choice for toolrooms and service departments that prioritise reliability and quick turnaround. Technical advice is available from Metav Werkzeuge for material-specific recommendations and best-practice tapping parameters. For TECWERK quality with workshop-ready availability, contact Metav Werkzeuge for supply and expert advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867130NW Label: Handgewindebohrer DIN 352 Nr.1 M3x0,5mm HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867130NW Facts Thread: M3 x 0.5 mm Shank diameter: 16 mm Application tensile strength: up to approx. 900 N/mm² Tolerance: ISO2 (6H) Special features Material: HSS Standard: DIN 352 Reference: DIN 13 Blatt 1 Cutting direction: right-hand Metric ISO-thread, right-hand cutting FAQ What thread size does this tap produce? The tap produces an M3 x 0.5 metric thread as stated in the product designation and meets the metric ISO thread form. Is the tool suitable for use in hard steels? The TECWERK hand tap is suitable for steels up to approximately 900 N/mm²; for harder materials alternative tooling or specialised taps should be considered. What is the shank diameter and how does that affect clamping? The tool has a shank Ø 16 mm, which allows secure clamping in standard tap handles and compatible collets for stable manual operation. Which tolerance class is achieved with this tap? This tap is manufactured to ISO2 (6H) tolerance, providing robust dimensional accuracy for general engineering applications. Which standards does the tap comply with? Manufacturing references include DIN 352 and DIN 13 Blatt 1, ensuring conformity with recognised German and international threading norms. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Reliable thread quality and efficient workshop use result from the combination of HSS construction, precise ISO2 (6H) tolerancing and a practical three-stage tap sequence; ideal for metric M3 thread production in steel. Order the set directly via Metav Werkzeuge or request advice from their consultants. TECWERK Hand Tap Set M3 x 0.5 HSS, ISO2 (6H) – 3-piece The TECWERK hand tap set M3 x 0.5 HSS ISO2 (6H) is a manual tapping solution for cutting metric M3 threads in general workshop and light industrial applications HSS material for durable cutting performance Metric M3 x 0.5 with ISO2 (6H) tolerance Suitable for through and blind holes in steels Consistent assembly with standardised metric threads The set delivers consistent M3 x 0.5 threads thanks to conformity with DIN 13 Blatt 1 and the ISO2 (6H) tolerance field, ensuring mating fasteners fit predictably. For production and repair work this means fewer rejected assemblies and faster alignment during assembly operations. The adherence to recognised standards reduces inspection time and simplifies documentation for quality control, contributing to a smoother production workflow without the need for complex post-processing. Reliable cutting performance for medium-strength steels Constructed from HSS, the taps are designed to cut in steels up to approximately 900 N/mm² tensile strength; the cutting geometry is right-hand. High-speed steel offers a balance of hardness and toughness, so chips form cleanly while the tool resists premature wear under normal tapping speeds. The 3.5 mm shank enables secure clamping in standard tap handles or adaptors, giving stable torque transfer and reduced wobble during manual operation. Basic lubrication and correct spindle alignment significantly extend service life. Practical three-step design reduces rework and cycle time The set comprises a progressive sequence of taper, intermediate and plug taps to split the cutting task into controlled stages. Beginning with a tapered lead reduces thread entry forces, the intermediate removes most material, and the plug produces the final thread to the ISO2 tolerance. This approach minimises tool breakage and lowers the risk of distorted threads in both through and blind holes, which is particularly beneficial in small-batch production and maintenance tasks. The compact set supports quick exchange and straightforward maintenance, helping workshops keep processes efficient. For secure metric M3 threading and straightforward technical guidance, contact Metav Werkzeuge in Emmerich for procurement and consultation — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000867110NW Product designation: Hand tap set M3 x 0.5 HSS ISO2 (6H) TECWERK Facts Thread: M3 x 0.5 mm Shank diameter: 3.5 mm Pieces: 3 Suitable for steels up to approx. 900 N/mm² Design & Special features Material: HSS Standard: DIN 352; thread standard DIN 13 Blatt 1 Right-hand cutting Tolerance field: ISO2 (6H) For through and blind holes Set composition: taper, intermediate, plug taps Brand: TECWERK FAQ What materials can be machined with this tap set? The TECWERK hand tap set M3 x 0.5 HSS ISO2 (6H) is specified for use in steels up to approximately 900 N/mm² tensile strength and is suitable for standard workshop steel grades. Does the set include the three tap stages for progressive threading? Yes, the delivery comprises taper, intermediate and plug taps, designed to be used in sequence to reduce cutting forces and minimise risk of tool breakage. Which standards and tolerances do the produced threads meet? Threads produced with this set conform to DIN 13 Blatt 1 and the tolerance field ISO2 (6H), providing reliable fit for metric fastenings. Can the set be used for blind holes as well as through holes? The tool geometry and set composition are suitable for both through and blind holes; using the progressive sequence helps prevent chip packing in blind holes. What is the shank size and how is the set identified? Shank diameter is 3.5 mm; the article number is 2000867110NW and the product is supplied under the TECWERK label Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from the combination of durable HSS cutting material, ISO2 (6H) tolerance for precise fits and a 22 mm shank for secure clamping; these features support reliable thread production and repeatable results. Order the TECWERK hand tap directly via Metav Werkzeuge or consult our specialists for application advice. Hand tap DIN 352 No.3 M30×3.5 HSS ISO2 (6H) TECWERK — HSS metric hand tap with ISO2 tolerance The Hand tap DIN 352 No.3 M30×3.5 HSS ISO2 (6H) is a precision hand tap intended for cutting metric ISO threads in steels with tensile strengths up to approximately 900 N/mm², complying with DIN geometry standards. HSS construction for long service life DIN 352 standardised geometry ISO2 (6H) tolerance for precision fit Shank Ø 22 mm for secure clamping Consistent thread quality through standardised geometry and tolerance The tap follows DIN 352 geometry and the DIN 13 Sheet 1 metric thread form, which ensures a predictable cutting profile and consistent thread form across batches. The ISO2 (6H) tolerance field is targeted toward general engineering fits where a precise, yet machinable fit is required; this reduces rework and simplifies quality control. Using a tool manufactured from HSS means the cutting edges retain hardness and resist wear under typical workshop conditions, supporting repeatable tolerances over many cycles. For production planning, the standardised dimensions and tolerance class make process verification straightforward and traceable. Robust design for secure clamping and efficient handling A 22 mm shank diameter provides a stable interface with manual tap wrenches and machine adaptors, improving torque transfer and reducing the risk of tool slippage during threading operations. The right‑hand cutting direction matches conventional tapping practice and simplifies integration into existing workflows. Because the tool is made of high‑speed steel, it balances toughness and hardness to withstand interrupted cuts and typical workshop contaminants. The practical result is reduced downtime: quicker set‑up, safer manual handling and fewer damaged workpieces, all of which contribute to improved throughput and lower scrap rates. Suitable applications, care and workshop integration This TECWERK hand tap is optimised for machining M30×3.5 metric threads in carbon and alloy steels up to roughly 900 N/mm², making it appropriate for heavy‑duty maintenance, replacement parts and small‑batch production. The standardised form makes gauging and inspection simpler; a calibrated thread gauge and a precision caliper are sufficient for routine acceptance checks. To preserve cutting performance, apply suitable cutting fluid and avoid excessive axial force; worn taps should be replaced to maintain thread quality. For complex or high‑volume tasks the same specifications allow easy transition to machine taps with compatible geometries. Discuss compatibility and secure supply through Metav Werkzeuge — contact our Emmerich team at info@metav-werkzeuge.com or +49 2822 7131930 for tailored guidance and order processing Technical data Article number: 2000867134NW Designation: Hand tap DIN 352 No.3 M30×3.5 HSS ISO2 (6H) TECWERK Brand: TECWERK Packaging unit: 1 Facts Thread size: M30 × 3.5 Shank diameter: 22 mm Suitable for steels: up to approx. 900 N/mm² Tolerance field: ISO2 (6H) Special features Material: HSS Standard: DIN 352 Thread standard: DIN 13 Sheet 1 (metric ISO thread) Right‑hand cutting FAQ What materials is this tap suitable for? This hand tap is designed primarily for carbon and alloy steels up to approximately 900 N/mm² and performs well where HSS taps are typically used. What does ISO2 (6H) tolerance mean for the finished thread? ISO2 (6H) indicates a commonly used tolerance class for internal threads that provides a close, reliable fit suitable for general engineering applications; it balances assembly ease with a secure fit. How should the tap be clamped for safe operation? Use a secure tap wrench or appropriate adaptor for a 22 mm shank and ensure concentric clamping to reduce bending and minimise the risk of breakage. Is this tap suitable for production or workshop maintenance? The DIN 352 geometry and HSS construction make it appropriate for workshop maintenance and small‑batch production where standard metric threads are required. What maintenance keeps the tap performing reliably? Regular cleaning, correct cutting fluid and avoiding excessive force will extend tool life; replace the tap when cutting edges blunt to maintain thread quality. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Reliable metric threading is achieved through the combination of durable HSS cutting edges and precise ISO2 (6H) tolerance, making M30 x 3.5 mm threads consistent in steels up to approx. 900 N/mm²; the three-stage tap sequence (pre‑, middle‑, finish) reduces rework and improves assembly fit. Order the Hand tap set DIN 352 M30 x 3.5 mm directly via Metav Werkzeuge or ask the consultants if needed. Hand tap set DIN 352 M30 x 3.5 mm HSS ISO2 (6H) — TECWERK The Hand tap set DIN 352 M30 x 3.5 mm HSS ISO2 (6H) is a manual tapping set for creating metric ISO threads in steels and general workshop applications High-performance HSS cutting material Metric ISO thread to DIN 13 specification ISO2 (6H) tolerance for precise fit Designed for through and blind holes Precise metric threads that cut rejection rates The set delivers consistent M30 x 3.5 mm threads by combining the DIN standard geometry with the ISO2 (6H) tolerance, which is common for screw fits requiring reliable assembly. The three-step sequence of pre‑, middle‑ and finish tap controls chip formation and reduces the load on the final thread form, lowering the likelihood of cross‑threading and rejected parts. For production or repair work, this predictability translates into fewer interruptions and less secondary dressing of components. Robust cutting performance for steel machining Manufactured from high-speed steel (HSS), these taps retain cutting edge integrity under intermittent hand use and moderate mechanical tapping. The right-hand cutting geometry and shank Ø18 mm offer stable engagement with standard tap holders, while the material choice supports operation in steels up to about 900 N/mm² tensile strength. Using a dedicated roughing, intermediate and finishing sequence optimises tool life and produces clean thread flanks—helpful where post‑process inspection and torque control are critical. Workshop-ready set that simplifies threading tasks The set is specified for both through and blind holes, allowing flexible deployment across maintenance benches and small production cells. Supplied as a coordinated set, the taps harmonise thread runout and pitch to reduce assembly variance and speed up fitting. The compact kit reduces inventory complexity compared with mixed, single‑tap purchases and integrates easily with standard tapping accessories. If application limits are unclear, Metav Werkzeuge’s technical resources can advise on compatibility and best practice for tapping speed, lubrication and hole preparation. For dependable metric threading with TECWERK quality, contact Metav Werkzeuge for precise supply and consultancy: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: 2000867125NW Product: Hand tap set DIN 352 M30 x 3.5 mm HSS ISO2 (6H) 3-piece Brand: TECWERK Facts Thread: M30 x 3.5 mm Tolerance: ISO2 (6H) Shank diameter: 18 mm Set pieces: 3 Suitable tensile strength: up to approx. 900 N/mm² Special features Material: HSS Metric ISO thread to DIN 13 Blatt 1 Right-hand cutting For through and blind holes Three-stage tap sequence: pre, middle, finish FAQ What materials can be threaded with this set? The Hand tap set DIN 352 M30 x 3.5 mm from TECWERK is specified for steels up to approximately 900 N/mm² tensile strength and is suitable for standard workshop steel applications. Is the set suitable for blind holes as well as through holes? Yes, the taps are designed for both through and blind holes; the three-stage sequence helps control chip evacuation in blind hole situations. What tolerance class does the set produce? Threads created with this set conform to ISO2 (6H) tolerance, providing a standard fit and reliable assembly behaviour. Which standard does the thread geometry follow? Thread geometry follows DIN 13 Blatt 1 in combination with DIN 352 tap type specification to ensure compatibility with metric ISO screws. What are the components of the set? The kit comprises the roughing (pre), intermediate (middle) and finishing (finish) taps to establish and refine the thread form for consistent results. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a tried-and-tested combination of HSS cutting material and DIN 352 hand‑tap geometry for consistent, repeatable thread quality; the tolerance ISO2 (6H) ensures secure assembly in metric applications. Order the tool directly via Metav Werkzeuge or consult the technical team for specification support. TECWERK hand tap DIN 352 No. 2, M3 x 0.5 mm HSS, ISO2 (6H) — right‑hand cutting, shank Ø 3.5 mm A TECWERK hand tap DIN 352 No. 2 M3 x 0.5 mm designed for producing metric ISO threads in medium‑strength steels and workshop applications. HSS construction for long tool life DIN 352 geometry for hand tapping Metric ISO thread M3 x 0.5 mm Tolerance ISO2 (6H) for precise fits Precision threading for reliable assemblies The tap follows DIN 352 geometry and produces metric ISO threads to DIN 13, delivering a defined fit class ISO2 (6H) for consistent mating with standard nuts and threaded components. This tolerance class prioritises a precise clearance that reduces play while avoiding excessive interference, which is particularly important in serial assembly or repair work. The controlled thread form minimises reworking and supports predictable torque behaviour in finished joints. Robust cutting performance and durability Made from HSS, the tool offers a balance of hardness and toughness suitable for manual tapping operations; HSS resists wear and maintains cutting edges longer than general‑purpose carbon steels. The tap is specified for use in steels up to approx. 900 N/mm² tensile strength, which covers a wide range of common workshop materials. Right‑hand cutting geometry ensures conventional clockwise threading and reliable chip formation when used with appropriate cutting lubricant, promoting smooth cutting action and reduced risk of thread distortion. Practical handling for workshop integration With a shank Ø 3.5 mm, the tool is sized for compatibility with standard tap wrenches and small chucks used in bench operations. The tool’s designation as a hand tap implies that the flute design and cutting sequence are optimised for manual feed, providing predictable chip evacuation when used correctly. For thread preparation, follow standard pilot drilling recommendations to match the M3 x 0.5 mm nominal size; correct pilot preparation combined with suitable lubricant extends tool life and improves surface finish. For occasional production runs or maintenance work, the geometry supports repeatable results without specialised machinery. For reliable thread production with TECWERK hand taps, contact Metav Werkzeuge for tailored advice or to place an order — info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: 2000867150NW Label: Handgewindebohrer DIN 352 Nr.2 M3x0,5mm HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Facts Thread size: M3 x 0.5 mm Shank diameter: 3.5 mm Material suitability: steels up to approx. 900 N/mm² Tolerance class: ISO2 (6H) Special features Material: HSS (high‑speed steel) Standard: DIN 352 hand tap geometry Thread standard reference: DIN 13 (metric ISO) Cutting direction: right‑hand cutting FAQ What materials is this hand tap suitable for? The TECWERK hand tap is specified for use in steels up to approx. 900 N/mm² tensile strength and is manufactured from HSS to handle typical workshop steel grades. What does the tolerance ISO2 (6H) mean for assembly? ISO2 (6H) denotes a medium‑tight tolerance for metric threads, providing a secure fit with standard nuts and threaded parts while avoiding excessive interference in typical engineering assemblies. Is the tap suitable for machine tapping? This tool is designed to DIN 352 hand‑tap geometry; while it may be used in light‑duty machine setups, it is optimised for manual tapping and standard tap wrench use. Which pilot drill size should be used before tapping M3 x 0.5 mm? Follow the standard pilot drill recommendations for an M3 x 0.5 mm metric thread to ensure correct root diameter and best thread quality; appropriate pilot preparation reduces cutting forces and extends tool life. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of precision ground HSS taps and ISO2 (6H) tolerance to produce consistent metric threads in both through and blind holes. The two‑stage design with pilot and finishing cutters reduces rework and extends tool life; order the set directly via Metav Werkzeuge or request advice from our consultants. HexTap Hand Tap Set M3–M20, HSS‑G, ISO2 (6H) — VÖLKEL HexTap Hand Tap Set M3–M20 delivers metric ISO threads for general workshop and maintenance use, combining ground HSS cutting edges with a two‑stage tap geometry for reliable thread form and reduced tapping forces. HSS‑G ground high‑speed steel taps Two-sided taps with pilot and finish cutters Metric ISO threads to DIN 13, tolerance ISO2 Consistent thread quality from ground HSS material The HexTap hand tap set is engineered with HSS‑G cutting material and a two‑step geometry to guarantee a defined thread profile under varied workshop conditions. Ground high‑speed steel provides a sharp, wear‑resistant cutting edge that maintains form over multiple uses. Compliance with DIN 13 and the ISO2 (6H) tolerance field ensures that internal threads match standard bolts and components, supporting interchangeability and reducing assembly issues. The kit is intended for reliably producing metric threads in typical engineering materials up to approximately 900 N/mm² tensile strength. Two‑stage cutting for efficient production and reduced rework A sequence of pre‑cut and finish‑cut flutes is built into the design to split material removal into controlled steps: the pre‑cut forms the initial thread, while the finish‑cut completes the profile to standard tolerance. This staged approach lowers cutting forces, reduces torque peaks and helps avoid tap breakage in hand operations. The result is fewer scrapped parts, less rework and a smoother tapping process for both through and blind holes. For maintenance and light production environments, this means faster job turnaround with consistent results. Broad size range for common workshop applications Covering sizes M3–M20, the set addresses a wide span of fastening needs encountered in mechanical workshops, toolrooms and service departments. The taps are suitable for unalloyed and low‑alloy steels and other readily machinable materials, delivering a practical solution when metric ISO threads are required on assemblies or repairs. The range minimises the need to source individual taps for each common size and supports standardisation of in‑house tooling. Practical handling and expected outcomes in everyday use Designed as a hand tap set, the geometry balances ease of start, cutting reliability and thread accuracy. Use in combination with appropriate tapping practice — correct alignment and steady feed — yields threads that meet the declared tolerance class and provide secure fastenings. The two‑step design also helps users new to manual tapping achieve better results sooner, while experienced operatives will appreciate the consistent thread form and reduced likelihood of tap wear or failure. For reliable metric threading choose the VÖLKEL HexTap hand tap set and contact Metav Werkzeuge for expert advice and procurement via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 4000867038NW Label: Handgewindebohrersatz HexTap M3-M20 HSSG ISO2 (6H) VÖLKEL Manufacturer: VÖLKEL GmbH Packaging unit: 1 Facts Thread range: M3–M20 Tolerance: ISO2 (6H) Suitable material tensile strength: up to approx. 900 N/mm² Standards: DIN 13, DIN ISO 228 Special features Cutting material: HSS‑G (ground high‑speed steel) Two-sided taps with pre‑ and finish cutters For through and blind holes Metric ISO threads and Whitworth pipe thread G per DIN ISO 228 Recommended for unalloyed and low‑alloy steels and readily machinable materials FAQ What materials can be machined with this tap set? The HexTap hand tap set from VÖLKEL (SKU 4000867038NW) is specified for unalloyed and low‑alloy steels and other well machinable materials, up to roughly 900 N/mm² tensile strength. Is the set suitable for blind holes as well as through holes? Yes, the two‑stage geometry of the VÖLKEL HexTap hand tap set is designed for both through and blind holes, allowing controlled chip removal and accurate finishing. Which thread standard and tolerance does the kit meet? Threads are formed to metric DIN 13 with tolerance field ISO2 (6H); the set also addresses Whitworth pipe threads G in accordance with DIN ISO 228 where applicable. How does the two‑stage tap design benefit everyday workshop use? Splitting cutting into pre‑cut and finish‑cut steps reduces torque and wear during tapping, delivering more consistent threads and fewer broken taps when using the HexTap hand tap set. Can the taps be used for stainless or hardened steels? The VÖLKEL HexTap hand tap set is specified for good machinable materials and steels up to about 900 N/mm²; for stainless or hardened steels consult material‑specific tooling recommendations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Reliable thread preparation with HSS cutting material and ISO2 (6H) tolerance ensures consistently accurate M4 x 0.7 threads in both through and blind holes; the progressive three-stage design minimises rework and extends tool life. Order the hand tap set directly via Metav Werkzeuge or consult our experts for suitability and delivery. TECWERK Hand Tap Set M4 x 0.7 — HSS, ISO2 (6H) TECWERK Hand Tap Set M4 x 0.7 HSS ISO2 (6H) is a manual tapping kit engineered for precise metric thread production in workshop and industrial settings. HSS construction for long service life Metric M4 x 0.7 thread to ISO standard ISO2 (6H) tolerance for accurate fits For through and blind hole tapping Precision threading for consistent assembly The set delivers reliable M4 x 0.7 threads to ISO2 (6H) tolerance, which translates into predictable fits and reduced assembly rejects. Made from HSS, the cutters maintain edge integrity during progressive cutting stages, so tapping performance remains stable even in repetitive operations. Conformity to recognised standards such as DIN 352 and DIN 13 Sheet 1 provides compatibility with common engineering specifications and simplifies quality assurance procedures. Versatile performance across common workshop materials Designed for use in a wide range of components, the taps are suitable for machining steels with tensile strengths of up to 900 N/mm², enabling work on typical workshop alloys without premature wear. The geometry supports both through and blind holes, so drilling strategies can remain flexible. Where material hardness and component design vary, the set’s specification reduces the need for multiple tool types, contributing to leaner tool inventories and faster process planning. Workshop-ready three-stage cutting for reduced rework Supplied as a three-piece set—rough, intermediate and finishing cutters—the progression minimises cutting forces and improves chip evacuation, which in turn lowers the risk of thread distortion or breakage. The 4.5 mm shank diameter provides secure clamping in manual holders, while the right-hand cutting direction aligns with standard drilling setups. This staged approach benefits operators by shortening setup times and producing threads that require less post-processing. Built to standards with serviceability in mind Construction in high-speed steel and adherence to metric standards ensure predictable wear patterns and straightforward replacement cycles. The conservative machining limits and clear specification support maintenance planning and spare-part logistics, helping to keep production downtime to a minimum. Paired with Metav’s quality-filtered supply chain and workshop-focused distribution from Emmerich, the kit is positioned as a dependable, everyday solution for precision tapping tasks. Contact Metav Werkzeuge for tailored advice and reliable dispatch from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 to confirm suitability and delivery options Technical data Article number: 2000867111NW Designation: Hand tap set DIN 352 M4 x 0.7 HSS ISO2 (6H) Packaging unit: 1 Manufacturer: TECWERK Facts Thread size: M4 x 0.7 Shank diameter: 4.5 mm Set: 3 pieces Suitable for steels up to 900 N/mm² Tolerance field: ISO2 (6H) Special features Material: HSS (high-speed steel) Right-hand cutting Standards: DIN 352, DIN 13 Sheet 1 For through and blind holes Progressive set: rough, intermediate, finishing FAQ Can these taps be used for blind holes? Yes. The TECWERK Hand Tap Set M4 x 0.7 HSS ISO2 (6H) is specified for both through and blind hole applications and includes the staged cutters needed for reliable blind-hole tapping. What materials are suitable for these taps? The set is designed for steels up to approximately 900 N/mm² tensile strength; the HSS cutting material provides robustness for common workshop steels. What does ISO2 (6H) tolerance mean in practice? ISO2 (6H) denotes a standard metric tolerance class for internal threads, providing an accuracy level that ensures interchangeable fits in standard fasteners and assemblies. What is included in the kit and why is it beneficial? The three-piece kit comprises rough, intermediate and finishing taps; this progression reduces cutting forces, improves chip control and yields more accurate final threads, lowering rework rates. Is the shank size compatible with manual holders? The taps have a 4.5 mm shank diameter, suitable for standard manual holders and collets commonly used in workshop tapping tasks. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of HSS cutting material, DIN 352 geometry and precise ISO2 (6H) tolerance to produce repeatable metric threads in demanding steels; buy via Metav Werkzeuge or consult the team for selection advice. Hand Tap DIN 352 No.1 M4 x 0.7 HSS ISO2 (6H) – Hand Tap by TECWERK The Hand Tap DIN 352 No.1 M4 x 0.7 HSS ISO2 (6H) TECWERK is a manual threading tool for producing standard metric threads in medium-strength steels, designed to meet DIN 13 sheet 1 thread form and provide consistent ISO tolerance class results. HSS material for long tool life Metric M4 x 0.7 ISO thread Tolerance ISO2 (6H) precision Suitable for steels up to 900 N/mm² Precision threading that reduces rework and scrap The tap is manufactured to DIN 352 standards and specified for the M4 x 0.7 metric thread, delivering a predictable thread form in accordance with DIN 13 sheet 1. Its ISO2 (6H) tolerance ensures mating parts fit within tight limits, which lowers the risk of rework and scrap. Built from HSS, the tool resists wear during manual threading operations and maintains cutting geometry for a reliable process outcome, particularly when machining steels up to ~900 N/mm² tensile strength. Consistent performance and simple process integration With a shank Ø 4.5 mm and right‑hand cutting geometry, the tool integrates easily with conventional tap handles and manual tapping stations. The combination of standardised geometry and robust HSS composition reduces unexpected tool failures and shortens setup time, supporting steady throughput in small-batch production or repair workflows. The predictable service life and consistent cutting action contribute to process stability and a more economical production rhythm. Practical selection and workshop use This hand tap is suitable where manual threading remains the method of choice: maintenance benches, prototyping and small-series assembly. The standardised dimensions and tolerance class allow direct comparison with alternative taps when planning tooling assortments, making procurement and stock management simpler. The hand tap’s specification supports decision-making for mixed-metal workshops that require metric thread capability without investing in dedicated tapping heads. For reliable metric threading with TECWERK quality and workshop-ready robustness, contact Metav Werkzeuge to arrange supply and technical advice on integrating this hand tap into existing tooling sets. Technical Data Article number: 2000867131NW Manufacturer: TECWERK Packaging unit: 1 Facts Thread size: M4 x 0.7 Shank diameter: 4.5 mm Suitable for steels up to: ca. 900 N/mm² Tolerance: ISO2 (6H) Special features Material: HSS Standard: DIN 352 Thread form: DIN 13 sheet 1 Cutting direction: right‑hand cutting Application: metric ISO thread production FAQ What materials is this hand tap suitable for? The Hand Tap DIN 352 No.1 M4 x 0.7 HSS ISO2 (6H) TECWERK is specified for use in steels up to approximately 900 N/mm² tensile strength and is optimised for common workshop steel grades. Which tolerance and thread standard does the tool follow? This threading tool produces M4 x 0.7 threads to DIN 13 sheet 1 with a tolerance class of ISO2 (6H) for consistent assembly fit. What is the shank diameter and how does it affect holder compatibility? The shank diameter is 4.5 mm, which is suitable for standard tap handles and manual tapping fixtures commonly used in maintenance and small-scale production. Is this a cut‑type and what cutting direction does it have? The tap is a right‑hand cutting tool made from HSS, designed for conventional clockwise tapping in manual operations. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS construction, DIN 352 geometry and ISO2 (6H) tolerance for reliable, repeatable metric threads in workshop production; order the tap directly via Metav Werkzeuge or consult Metav's specialists for tailored recommendations. Hand Tap M4 x 0.7 HSS, ISO2 (6H) – TECWERK A compact hand tap designed for cutting M4 x 0.7 metric ISO threads in steels up to approximately 900 N/mm², suitable for manual workshop and maintenance use. HSS material for robust cutting DIN 352 geometry, right‑hand cut ISO2 (6H) tolerance for precise fits Consistent thread quality from HSS and proven geometry The combination of HSS cutting material and DIN 352 geometry delivers durability and repeatability for manual tapping operations. The high‑speed steel cutting edges provide a good balance between wear resistance and toughness, which is particularly advantageous when working with medium‑strength steels. The right‑hand cutting flutes are tailored for conventional drilling and tapping sequences, ensuring stable chip evacuation and reduced risk of breakage during standard workshop tasks. Precise assembly outcomes thanks to ISO2 tolerance The M4 x 0.7 specification with ISO2 (6H) tolerance ensures a tight and predictable thread fit suitable for general mechanical assemblies. ISO2 (6H) denotes a standard metric tolerance class that yields a reliably close fit with corresponding bolts; this reduces the need for trial‑and‑error adjustments and minimises rework. The tap's nominal 4.5 mm shank diameter provides secure clamping in common tap wrenches, supporting accurate alignment and even torque transfer for consistent thread form. Efficient handling and reduced process interruptions Designed for hands‑on workshop environments, the tool focuses on practical operation and uptime. The HSS cutting material withstands frequent use in steels up to approximately 900 N/mm², delivering sustained cutting performance without complex maintenance. The geometry specified to DIN 352 assists with controlled chip breakage, lowering the chance of chip packing and the need to stop for clearing. Supplied as a single unit, the tap integrates easily into existing tooling sets and supports quick replacement when required. Clear technical compatibility and application guidance The tool is intended for creating metric ISO threads and follows recognised standards for interchangeability and assembly. Working within its specified material range avoids overstressing the tool and helps maintain sharp cutting edges longer. For manual tapping, appropriate lubrication and correct spindle alignment remain key to achieving the nominal tolerance and prolonging tool life. The design is straightforward, making it a practical choice for workshops seeking dependable threading with minimal setup complexity. For reliable metric threading from a reputable brand, request the TECWERK hand tap via Metav Werkzeuge or contact Metav's consultants for advice on selecting the right tap for specific materials and applications. Technical Data Article number: 2000867151NW Product name: Hand Tap M4 x 0.7 HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867151NW Facts Thread: M4 x 0.7 Shank diameter: 4.5 mm Material: HSS Standard: DIN 352; DIN 13 Part 1 Tolerance: ISO2 (6H) Application strength: steels up to ≈ 900 N/mm² Cutting direction: right‑hand cut Special features Metric ISO thread form Designed for manual tapping Optimised flute geometry for chip control Suitable for workshop maintenance and production Single‑piece supply FAQ What materials is this tap suitable for? The TECWERK hand tap M4 x 0.7 is specified for use in steels up to approximately 900 N/mm²; the HSS material provides wear resistance for such applications. Is the thread tolerance suitable for standard fasteners? Yes, the ISO2 (6H) tolerance class used by the tap aligns with common metric bolt tolerances and supports reliable assembly fits. Can this tap be used in a tap wrench with a 4.5 mm clamping diameter? The tap features a 4.5 mm shank diameter and is compatible with standard tap wrenches that accept this shank size. Does the product follow recognised standards for thread form and pitch? The tool conforms to DIN 352 geometry and the thread follows metric ISO specifications as referenced in DIN 13 Part 1. What is the SKU for ordering or reference? The SKU for this item is 2000867151NW; it is listed as Hand Tap M4 x 0.7 HSS ISO2 (6H) TECWERK. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a durable HSS construction combined with an ISO2 (6H) tolerance for consistently accurate metric threads and dependable performance in steels up to approx. 900 N/mm²; order directly via Metav Werkzeuge or contact the consultants for tailored advice. Hand tap DIN 352 No.3 M4x0.7mm HSS ISO2 (6H) TECWERK — HSS hand tap for metric M4 threads, ISO2 tolerance Hand tap DIN 352 No.3 M4x0.7mm HSS ISO2 (6H) TECWERK is a manual threading tool for producing precise internal metric threads in general workshop and industrial applications HSS material for durable cutting Metric ISO thread M4 x 0.7 DIN 352 standard, right-hand cutting Tolerance ISO2 (6H) for precise fit Accurate threads that reduce rework and assembly time The ISO2 (6H) tolerance ensures a tighter fit for internal threads, which translates into fewer assembly adjustments and reduced rejection rates. Designed for metric threads M4 x 0.7, this hand tap follows the DIN 352 specification and DIN 13 Blatt 1 guidance, making it straightforward to match with standard bolts and components. By choosing a tool with defined tolerance and standard conformity, process planners and workshop managers secure predictable results and minimise downtime for thread correction. Robust cutting performance for a wide range of steels Manufactured from HSS, the tool provides a reliable cutting edge for materials up to roughly 900 N/mm² tensile strength, offering a balance between wear resistance and toughness. The right-hand cutting geometry and the defined shank Ø 4.5 mm facilitate secure mounting in conventional tap wrenches and holders while reducing the risk of breakage under typical manual loads. This combination of material and design supports efficient threading operations, lowering the frequency of tool changes and maintaining throughput on repetitive tasks. Simplified selection and dependable supply for workshops As a single-piece hand tap supplied in a packaging unit of 1, the tool suits spares provisioning and small-batch production alike. The clear specification—DIN 352, metric ISO thread, HSS cutting material—makes integration into procurement lists uncomplicated and supports inventory transparency. Metav’s offering places emphasis on accessible precision: experienced buyers benefit from centralised availability and a European quality filter that helps ensure consistent tool performance and dependable stock management. Contact Metav Werkzeuge for purchasing details or technical clarification on the TECWERK hand tap and secure reliable delivery from Emmerich. Technical Data Article number: 2000867171NW Label: Handgewindebohrer DIN 352 Nr.3 M4x0,7mm HSS ISO2 (6H) TECWERK Packaging unit: 1 Brand: TECWERK Facts Thread size: M4 x 0.7 Shank Ø: 4.5 mm Material strength suitability: up to approx. 900 N/mm² Tolerance: ISO2 (6H) Special features Material: HSS Standard: DIN 352 Thread standard reference: DIN 13 Blatt 1 Cutting direction: right-hand cutting Thread type: metric ISO FAQ What thread does the tap produce? The tap produces a metric internal thread M4 x 0.7, matching standard ISO metric fasteners and assemblies. Which materials can be machined with this tap? This TECWERK hand tap is intended for steels up to approximately 900 N/mm² tensile strength and performs well in general workshop steel applications. What standard does the tool conform to? The tool conforms to DIN 352 and the thread form follows DIN 13 Blatt 1, ensuring compatibility with standard ISO metric threads. Is the shank compatible with common holders? Yes, the shank Ø 4.5 mm is suitable for conventional tap wrenches and manual holders used in workshop environments. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of HSS construction, ISO2 (6H) tolerance and a three-stage tap progression for reliable, repeatable M5 metric threads in medium-strength steels — a setup designed for consistent workshop throughput. Order the TECWERK hand tap set directly via Metav Werkzeuge or consult our specialists for machining recommendations. TECWERK Hand Tap Set M5 x 0.8 HSS ISO2 (6H), 3-piece TECWERK Hand Tap Set M5 x 0.8 HSS ISO2 (6H) is a compact tapping kit for metric ISO threads, intended for manual use in general workshop and maintenance environments. High-speed steel (HSS) construction ISO2 (6H) tolerance for accurate fits Suitable for through and blind holes Three-piece progression: taper, plug, bottoming Precision and production consistency for metric M5 threads The set provides a three-stage cutting progression — taper, plug and bottoming — that reduces cutting forces and improves chip evacuation during manual tapping. Built in HSS, the tools retain cutting edge hardness while offering resilience against abrasion, which translates into consistent thread quality across multiple components. The ISO2 (6H) tolerance ensures that threads meet standardised dimensional requirements, making the kit suitable where reliable assembly fit is required. Efficient handling and safer tapping process A deliberate progression from rough to finish reduces the risk of tap breakage and simplifies manual control in common workshop scenarios. The taper tap starts the thread safely, the plug tap deepens it, and the bottoming tap completes threads to the full depth in blind-hole work. This staged approach lowers rework and supports faster throughput when producing multiple M5 threads, delivering measurable time savings in maintenance and small-batch production. Material range and machining capability explained The set is specified for use in steels up to approximately 900 N/mm² tensile strength, covering most mild and medium-alloy steels encountered in routine fabrication and repair. The tools are right-hand cutting and designed for metric ISO thread forms; these characteristics make them suitable for general metalworking and maintenance tasks where standard M5 x 0.8 threads are required. For materials outside this range or for production machining, consult technical advice before proceeding. Practical design details that matter at the bench Each tap in the set has a 6 mm shank diameter, compatible with common tap wrenches and holders, and is delivered as a three-piece kit for flexibility when working with through or blind holes. The compact format means easy storage and straightforward identification in a busy toolbox. Clear, standardised markings support traceability and reduce setup time when working across multiple machines or workstations. For precise M5 threading in workshop and maintenance environments, contact Metav Werkzeuge to request the TECWERK hand tap set (SKU 2000867112NW) or to obtain tailored machining recommendations via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000867112NW Label: Handgewindebohrersatz DIN 352 M5 x0,8mm HSS ISO2 (6H) 3tlg.TECWERK Manufacturer: TECWERK Facts Thread: M5 x 0.8 Standard: DIN 352; DIN 13 Blatt 1 Tolerance: ISO2 (6H) Material: HSS Shaft diameter: 6 mm Set composition: 3-piece (taper, plug, bottoming) Suitable for: Steels up to approx. 900 N/mm² Special features Right-hand cutting For through and blind holes Metric ISO thread form Packaging unit: 1 UID / SKU: 2000867112NW FAQ What materials is this tap set suitable for? The TECWERK hand tap set is specified for machining steels up to approximately 900 N/mm² tensile strength; the HSS cutting material supports conventional steel grades used in workshop repairs. How many taps are included and what are their roles? The kit comprises three taps — taper, plug and bottoming — providing a progressive workflow for safe thread starting, intermediate cutting and full-depth finishing. What does ISO2 (6H) tolerance mean for the finished thread? ISO2 (6H) denotes a standard internal thread tolerance that delivers a typical fit for general assembly; threads produced with this tolerance comply with metric ISO standards for reliable mating with standard bolts. Can the set create threads in blind holes? Yes — the three-stage progression and inclusion of a bottoming tap allow completion of threads to the base of blind holes without compromising thread integrity. Is the shank size compatible with common tap wrenches? Each tap has a 6 mm shank diameter, compatible with standard tap wrenches and manual holders typically available in workshops. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the robust combination of HSS cutting performance and ISO2 (6H) tolerance for consistently accurate metric threads; the compact shank Ø 6 mm ensures secure clamping and reliable workshop integration. Order the TECWERK hand tap directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK Hand tap DIN 352 No.1 M5 x 0.8 mm HSS ISO2 (6H) A Hand tap DIN 352 No.1 M5 x 0.8 mm HSS ISO2 (6H) designed for manual cutting of metric ISO threads in medium-strength steels and general workshop use HSS for durable cutting performance ISO2 tolerance (6H) for precise fits Right-hand cutting, DIN 352 geometry Shank Ø 6 mm for secure clamping Consistent thread accuracy and material suitability The tool is manufactured from HSS, following DIN 352 geometry, which provides stable chip formation and predictable wear characteristics; this results in reproducible thread profiles and less rework. The ISO2 (6H) tolerance ensures dimensional conformity with metric ISO standards, making the tap suitable for assemblies where fit and function matter. The specification for working in steels up to approximately 900 N/mm² signals compatibility with a wide range of carbon and alloy steels commonly encountered in maintenance and light production environments. Such clarity in material capability reduces the risk of incorrect tool selection and supports efficient process planning. Secure clamping and standard-compliant thread production Designed with a shank Ø 6 mm, the tap fits standard collets and holders, enabling firm clamping and minimising runout during manual operation. The M5 x 0.8 mm thread form conforms to DIN 13 sheet 1, so threads produced are directly interchangeable with standard fasteners and mating parts. The right‑hand cut and DIN‑compliant geometry combine to deliver a predictable hand‑tapping experience, reducing operator fatigue and the likelihood of cross-threading. For users integrating the tool into existing sets, the compact shank and standardised profile enable straightforward replacement and stock rationalisation. Durable performance and workflow benefits for workshops The compact design and proven HSS cutting material support long tool life under recommended use, contributing to fewer tool changes and lower downtime. The tool’s configuration makes it a practical choice for small-batch production, repair work and maintenance tasks where dependability matters. Where precision counts, the combination of standard conformity, robust material selection and a secure shank reduces inspection rejects and supports faster throughput. Complementing a broader tooling strategy, this hand tap provides a cost‑effective, maintenance‑light option to maintain thread quality across daily workshop demands. For TECWERK hand taps and technical advice, contact Metav Werkzeuge in Emmerich for availability and ordering; Metav’s specialists can confirm suitability for specific applications and advise on integration into existing tool sets Technical data Article number: 2000867132NW Label: Hand tap DIN 352 No.1 M5 x 0.8 mm HSS ISO2 (6H) TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867132NW Core data Shank diameter: 6 mm Thread size: M5 x 0.8 mm Suitable material strength: up to approx. 900 N/mm² Special features Material: HSS Standard: DIN 352, DIN 13 sheet 1 Cutting direction: right-hand cut Tolerance field: ISO2 (6H) Application: manual cutting of metric ISO threads FAQ What materials can be tapped with this hand tap? The TECWERK Hand tap DIN 352 No.1 M5 x 0.8 mm HSS ISO2 (6H) is specified for use in steels up to approximately 900 N/mm²; its HSS construction is suitable for common carbon and alloy steels encountered in workshops. What tolerance and thread standard does the tap produce? Threads produced by the tap conform to metric ISO standards (DIN 13 sheet 1) with an ISO2 (6H) tolerance, providing standardised fit and interchangeability with conventional fasteners. How should the tap be clamped for safe operation? Use a holder or collet that accepts a shank Ø 6 mm to ensure secure clamping and minimal runout; correct clamping supports consistent thread quality during manual tapping. Is this tap suitable for machine tapping? This product is a hand tap designed according to DIN 352 for manual use; while it may be used in certain light machine setups, it is optimised for hand-driven thread cutting and workshop applications. Are replacement or resharpening guidelines available? The tool’s HSS composition supports resharpening when required; consult Metav Werkzeuge for workshop-specific maintenance recommendations and reconditioning options. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from a robust combination of HSS cutting material and precise ISO2 (6H) tolerance for consistent, reliable M5 thread production; order the tap directly via Metav Werkzeuge or consult our specialists for technical guidance. Hand tap DIN 352 No.3 M5x0.8 mm HSS ISO2 (6H) — manual metric tap with 6 mm shank, right-hand cutting (TECWERK) The Hand tap DIN 352 No.3 M5x0.8 mm HSS ISO2 (6H) is a precision manual tapping tool designed for producing metric M5 threads in medium-strength steels; suitable for workshop repairs and small-batch production where controlled manual tapping is required HSS cutting material for durability Metric ISO M5x0.8 thread to DIN 13 ISO2 (6H) tolerance for accurate fits 6 mm shank, right-hand cutting Consistent thread quality for accurate assembly The tap is manufactured to DIN 352 and paired with the DIN 13 specification for metric threads, which ensures a predictable thread geometry and fit. With its ISO2 (6H) tolerance, the tool provides a reliably tight tolerance suitable for standard engineering assemblies; this reduces the need for rework and supports reproducible connections. The combination of standard conformity and measured tolerancing is especially valuable where interchangeability and assembly integrity are critical. Optimised for steel and manual shop work Made from HSS and specified for steels up to approximately 900 N/mm², the tool is aimed at conventional workshop materials rather than exotic alloys. The high-speed steel composition offers a balance of toughness and wear resistance for manual operations, and the right-hand cutting geometry matches conventional tapping practice. For operators less familiar with technical terms: HSS stands for high-speed steel, a material chosen because it withstands heat and preserves cutting edges under the friction typical of hand tapping. Practical design to simplify use and handling A 6 mm shank design facilitates secure clamping in standard tap wrenches and holders, keeping the tool centred and stable during insertion and withdrawal. The designation No.3 under DIN 352 indicates flute geometry and usable length appropriate for general-purpose hand taps, offering a compromise between chip evacuation and cutting engagement. Where manual control is required, this geometry supports safer, more controlled tapping and reduces the likelihood of breakage in routine workshop tasks. For precision M5 thread-making with the TECWERK hand tap, contact Metav Werkzeuge for expert advice and fast delivery from our Emmerich stock — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000867172NW SKU: 2000867172NW Manufacturer: TECWERK Data Thread: M5x0.8 mm Shank diameter: 6 mm Material strength suitability: up to approx. 900 N/mm² Special features Material: HSS Standard: DIN 352 Thread standard reference: DIN 13 Blatt 1 Cutting direction: right-hand Tolerance field: ISO2 (6H) FAQ What materials is this hand tap suitable for? The TECWERK hand tap is specified for use in steels up to approximately 900 N/mm² and is manufactured from HSS to suit standard workshop steel applications. What thread form and size does the tool produce? The tool produces a metric thread of M5x0.8 mm to DIN 13, manufactured to the ISO2 (6H) tolerance class for standard-fit assemblies. How is the tap held during manual tapping? The tap has a 6 mm shank designed for secure clamping in common tap wrenches and manual holders, providing stable control during hand tapping operations. Which standards does the tap comply with? This hand tap is made to DIN 352 and references DIN 13 Blatt 1 for the metric thread form and dimensions, ensuring conformity with common industrial specifications. Is this tap suitable for power tapping or only manual use? The designation and flute geometry correspond to a hand tap as per DIN 352; it is optimised for manual use rather than high-speed machine tapping. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Reliable, standards-compliant performance for metric internal threads combined with high-speed steel durability and a 6 mm shank make this hand tap a practical choice for workshop and industrial use; order via Metav Werkzeuge or consult the technical team for compatibility advice. Hand tap DIN 352 No.2 M5 x 0.8 mm, HSS, ISO2 (6H) — TECWERK Hand tap DIN 352 No.2 M5 x 0.8 mm HSS ISO2 (6H) for manual cutting of metric internal threads in medium‑strength steels and general workshop applications HSS cutting material for long tool life DIN 352 geometry for consistent thread form ISO2 (6H) tolerance for standard fit Suitable for steels up to approx. 900 N/mm² Precision and durability for repeatable thread quality Manufactured to DIN 352 with the thread form referenced in DIN 13 Blatt 1, this tool offers a repeatable and precise internal thread that meets standardised tolerances. The HSS cutting material provides wear resistance and toughness, reducing the frequency of tool changes in everyday workshop operations. The combination of standard geometry and robust material supports consistent results when producing M5 x 0.8 mm threads for assemblies that rely on interchangeability. Predictable performance in medium‑strength steels Designed for use in steels with tensile strength up to approx. 900 N/mm², the tap is suitable for a broad range of components commonly encountered in maintenance and fabrication. The ISO2 (6H) tolerance field ensures a standard clearance fit where specified, which helps to minimise rework and guarantee mechanical compatibility. Because the specification is explicit about material limits, selection becomes a matter of matching component requirements to the tool’s capabilities, reducing machining uncertainties. Practical handling and workshop integration With a 6 mm shank, the tool fits standard tap wrenches and holders, enabling quick setup and safe manual threading. The right‑hand cut geometry supports conventional rotational direction for most bench operations. For best results, employ suitable cutting fluid and controlled feed to preserve the cutting edges; the robust HSS substrate tolerates occasional higher loads better than softer steels. For technical queries regarding tool holders or application advice, Metav Werkzeuge provides product guidance and material compatibility information. For dependable metric threading using a DIN‑compliant HSS hand tap, contact Metav Werkzeuge to confirm suitability and place an order through their technical sales team at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 2000867152NW Manufacturer: TECWERK Packaging unit: 1 Core data Thread size: M5 x 0.8 mm Shank diameter: 6 mm Suitable material strength: up to approx. 900 N/mm² Tolerance field: ISO2 (6H) Standards: DIN 352; DIN 13 Blatt 1 Features Material: HSS (high‑speed steel) Right‑hand cutting Metric ISO thread for internal threads For manual tapping operations FAQ Is this tap suitable for stainless steel? The TECWERK hand tap is specified for steels up to approx. 900 N/mm²; stainless steel suitability depends on grade and hardness, so assess material properties before use. What thread tolerance does the tool produce? The tool produces a thread to ISO2 (6H) tolerance, providing a standard fit for general engineering assemblies. Which toolholder or wrench fits the shank? A standard tap wrench or holder accommodating a 6 mm shank is appropriate; secure clamping reduces runout and improves thread quality. TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund