Take advantage of the combination of HSS‑Co alloy, a vapourised nitride surface and straight‑fluted geometry for long tool life and consistent thread quality; order the component directly via Metav Werkzeuge or consult our experts for application support. Machine tap DIN 5156B VA G 1″ x 11 – HSS‑Co, vapourised, TECWERK The Machine tap DIN 5156B VA G 1″ x 11 HSS‑Co is a straight‑fluted production tap for cutting Whitworth pipe threads in demanding, hard‑to‑machine materials HSS‑Co high‑performance alloy Vapour‑treated surface finish Straight flutes with chamfered flanks Durable cutting performance for heavy‑duty work The high‑alloy HSS‑Co composition delivers elevated red‑hardness and wear resistance, which extends tool life under continuous operation. Combined with the vapourised nitride surface treatment, the tool shows improved adhesion resistance and lower friction at the cutting edge. These properties translate into fewer tool changes and steadier production throughput when machining difficult materials, supporting predictable cycle times and reduced downtime. Accurate Whitworth pipe threads to industry standard Designed for Whitworth G pipe thread form and produced to DIN ISO 228, the tap creates reliable, standardised threads suitable for piping and hydraulic connections. The geometry features chamfered flanks to promote a clean thread form and reduce burr formation; this benefits assembly readiness and sealing performance. Where consistent thread profile and repeatability matter, this machining solution helps maintain dimensional conformity across batches. Designed for machine use and efficient chip control As a DIN 5156B (Form B) machine tap with a straight‑fluted design, the tool is optimised for through‑hole threading and machine mounting. The straight flutes facilitate controlled chip formation and evacuation in continuous production environments, reducing the risk of chip packing in through threads. The robust 25 mm shank diameter ensures stable clamping and torque transmission, improving concentricity and minimising chatter in automated tapping stations. Material compatibility and application scope This tool is specified as Type VA and is suited to hard‑to‑machine materials, including corrosion‑resistant and heat‑resistant steels with tensile strengths above 850 N/mm². The combination of substrate and surface treatment makes it appropriate for applications where elevated strength and resistance to built‑up edge are concerns. For standard through‑thread operations in industry sectors such as hydraulics, petrochemical fittings and high‑grade stainless assemblies, the tool provides a pragmatic balance of life and performance. Contact Metav Werkzeuge today for a tailored recommendation on TECWERK machine taps or request precise delivery and stocking information from our Emmerich warehouse Technical data Article number: 2000867499NW SKU: 2000867499NW Label: Maschinengewindebohrer DIN 5156B VA G 1 Zollx11 HSS‑Co vapor.ISO 228 TECWERK Manufacturer: TECWERK Packaging unit: 1 Core specifications Shank diameter: 25 mm Thread: G 1″ × 11 threads per inch Standard: DIN ISO 228 Form: DIN 5156B (Form B) Special features Material: HSS‑Co Surface: nitride and vapourised (vapour treated) Flute type: straight‑fluted Flank: chamfered flanks Identification: blue ring Application: through threads Suitable for: hard‑to‑machine materials, incl. stainless and heat‑resistant steels > 850 N/mm² tensile FAQ What thread standard does the tap produce? The tap produces a Whitworth G thread to DIN ISO 228, specified as G 1″ × 11 threads per inch for standard pipe connections. Is the tool suitable for stainless or heat‑resistant steels? Yes, the TECWERK machine tap with HSS‑Co material and vapourised surface is intended for hard‑to‑machine materials, including stainless and heat‑resistant steels with tensile strength above 850 N/mm². Which machine configuration is the tap intended for? This is a machine tap in DIN 5156B (Form B) design with a 25 mm shank for secure clamping and use in production tapping units. How does the surface treatment improve performance? The vapourised nitride finish reduces friction and improves wear resistance at the cutting edges, extending tool life and contributing to consistent thread quality. Can this tap be used for blind holes? The tool is optimised for through‑hole threads; for blind‑hole applications, a dedicated blind‑hole tap geometry is recommended. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Reliable thread production and extended tool life result from the combination of HSS‑Co construction and a 40° right‑hand spiral, ensuring efficient blind‑hole tapping in materials up to ≈1000 N/mm². Order the machine pipe tap directly via Metav Werkzeuge or consult our specialists for technical guidance. Machine pipe tap DIN 5156C G 1 inch x 11 HSS‑Co — machine tap for Whitworth pipe thread, TECWERK The Machine pipe tap DIN 5156C G 1 inch x 11 HSS‑Co is a robust machine tap designed for producing Whitworth G pipe threads to ISO 228, optimised for blind‑hole applications and high‑strength steels. HSS‑Co for enhanced wear resistance 40° right‑hand spiral for blind‑hole tapping Whitworth G thread to ISO 228 25 mm shank for secure machine clamping Precise pipe threads for secure, standardised connections The tap produces Whitworth G pipe threads in accordance with ISO 228, delivering parallel pipe threads where a reliable mechanical fit is essential. The HSS‑Co composition offers a balance of hardness and toughness, which maintains cutting geometry under load and high temperatures. For assemblies that require standardised interfacing and replaceable seals, this tool ensures repeatable thread profiles and reduces rework by producing accurate threads in blind bores. Engineered for fast, reliable blind‑hole tapping A 40° right‑hand spiral directs chips away from the cutting edge, significantly improving evacuation in blind‑hole operations and lowering torque peaks during tapping. The flute geometry and flank honing reduce the risk of chip jamming, enabling smoother cycles on CNC and automatic tapping heads. Combined with a 25 mm shank, the tool offers secure clamping for stable rotation and concentricity, which translates into shorter cycle times and fewer tool changes in production environments. Durable design and broad material compatibility Constructed in HSS‑Co and specified as Form C, the tap is built to withstand the demands of machining steels up to approximately 1000 N/mm² and temper cast iron. The hardened, honed flanks extend service intervals by improving edge stability and chip flow. This durability lowers total production interruptions and supports consistent thread quality across runs, offering cost efficiency through longer tool life and reduced scrap rates. For tailored advice on selecting the right TECWERK machine pipe tap or to secure this HSS‑Co G 1" x 11 tap for production use, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data Article number: 2000867515NW Description: Maschinengewindebohrer DIN 5156C G 1 Zollx11 HSS-Co ISO 228 TECWERK Manufacturer: TECWERK Facts Shank diameter: 25 mm Thread designation: G 1" x 11 Spiral angle: 40° Suitable tensile strength: up to approx. 1000 N/mm² Packaging unit: 1 Special features Material: HSS‑Co Form C Right‑hand spiral for chip evacuation Flanks honed (flanken hinterschliffen) Whitworth pipe thread to DIN ISO 228 Intended for blind‑hole threads Suitable for steel and temper cast iron FAQ Which thread standard does this tap produce? The tap produces Whitworth G pipe threads in line with ISO 228, suitable for standardised parallel pipe connections. Is this tap suitable for blind‑hole applications? Yes — the 40° right‑hand spiral and honed flanks make the TECWERK machine pipe tap especially effective for blind‑hole tapping. Which materials can be machined with this tap? The tool is specified for steels up to approximately 1000 N/mm² and for temper cast iron, providing reliable performance in these materials. What is the shank size and how is it clamped? The tap has a 25 mm shank, designed for secure clamping in machine tool holders and tapping heads to ensure concentricity. What is the SKU for ordering and reference? The SKU is 2000867515NW for the TECWERK machine pipe tap DIN 5156C G 1" x 11. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of high-strength HSS‑Co material, a vapour‑deposited coating and a rigid 25 mm shank for consistent thread quality and longer tool life; order the tap directly via Metav Werkzeuge or consult our specialists for application advice. Machine Tap DIN 5156B — Whitworth G 1" x 11, HSS‑Co (TECWERK) The Machine Tap DIN 5156B (G 1" x 11) is a universal, straight‑flute machine tap engineered for producing Whitworth pipe threads in steel, stainless steels and non‑ferrous metals. High‑performance HSS‑Co material Designed for Whitworth G 1" x 11 threads Straight flutes with flank relief Vapour‑deposited coating for wear resistance Reliable Whitworth pipe threads for industrial fittings The geometry complies with the Whitworth pipe‑thread specification and DIN ISO 228, which delivers repeatable, compatible threads for pipework and fittings. By using a machine tap built to these standards, the risk of mismatched threads or seal failures is reduced, resulting in fewer reworks and improved assembly reliability for hydraulic and pneumatic systems. Longer service life through material and coating Made from HSS‑Co (cobalt‑alloyed high‑speed steel), the tool offers improved hot hardness and edge retention compared with conventional high‑speed steels. The vapour‑deposited coating increases wear resistance and reduces adhesion of chips, extending cutting life under interrupted or continuous machining and lowering total tooling costs over production runs. Geometry designed for consistent performance The straight flutes and flank relief grinding promote controlled chip formation and reduce cutting forces, while the peel chamfer is optimised for through‑threads to ensure clean starts and reliable thread profiles. The 25 mm shank provides the rigidity needed for machine tapping, helping to maintain concentricity and reduce vibration during operation. Universal form and broad material compatibility Classified as Form B — universal, the tap is intended for machine use and is suitable for machining steel, stainless steels, spheroidal cast iron and non‑ferrous metals. This versatility makes it a practical choice for mixed‑workshop environments where a single, robust tool must perform across a range of components and alloys, simplifying tool management and inventory. Contact Metav Werkzeuge for tailored advice on TECWERK machine taps and to confirm compatibility with specific machines and materials Technical Data Article number: 2000867946NW SKU: 2000867946NW Product designation: Machine Tap DIN 5156B G 1" x 11 HSS‑Co TECWERK Facts Shank diameter: 25 mm Thread form: Whitworth pipe thread G 1" x 11 TPI Packaging unit: 1 Special features HSS‑Co material Form B (universal) Vapour‑deposited coating Green ring identification Straight fluted Flank relief ground Peel chamfer for through threads Conforms to DIN ISO 228 Suitable for steel, stainless steels, spheroidal cast iron, non‑ferrous metals FAQ What thread standard does this tap produce? The tap produces Whitworth pipe threads in accordance with DIN ISO 228; the specification corresponds to G 1" x 11 TPI for compatible piping and fittings. Which materials can be machined with this tap? This TECWERK machine tap is suitable for machining steel, stainless steels, spheroidal cast iron and non‑ferrous metals as indicated in the technical description. Is this tool intended for hand tapping or machine use? The tool is a machine tap in Form B (universal) and is designed for use on machines such as tapping heads or CNC tapping units rather than manual hand tapping. How does the coating affect tool life? The vapour‑deposited coating on the TECWERK tap improves wear resistance and reduces adhesion of chips, which generally extends service life and maintains thread quality over longer production runs. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the HSS‑Co wear resistance, the efficient chip evacuation of the 40° right‑hand spiral, and the universal Form C geometry for consistent Whitworth G threads; order the part directly via Metav Werkzeuge or consult the specialists for application advice. Machine tap DIN 5156C – Whitworth pipe thread G 1/2" x 14, HSS‑Co (TECWERK) The Machine tap DIN 5156C for Whitworth pipe thread G 1/2" x 14 (HSS‑Co) is a universal, spiral‑fluted machine tap engineered for blind‑hole G threads in steels, stainless steels, ductile iron and non‑ferrous metals HSS‑Co for high wear resistance Right‑hand 40° spiral flute for chip removal For blind holes and pipe threads G 16 mm shank for secure machine clamping Industrial‑grade cutting performance for consistent pipe threads The Machine tap DIN 5156C combines a cobalt‑alloy high‑speed steel (HSS‑Co) body with a Form C universal geometry to deliver reliable thread forms across mixed production runs. The vapour‑treated finish increases surface hardness and wear resistance, extending tool life under intermittent loads and higher temperatures. For shops producing Whitworth pipe threads, the adherence to DIN ISO 228 ensures compatibility with standard fittings and assemblies, reducing rework and assembly failures. The universal design maintains dimensional stability across different workpiece materials, which benefits batch processing and reduces tool changes. Controlled chip flow and safe blind‑hole tapping A 40° right‑hand spiral flute coupled with flank‑honed cutting edges provides active chip control and improved surface quality when working in blind holes. The spiral angle promotes chip evacuation into the flutes rather than packing at the thread root, lowering the risk of tap breakage and minimising operator interruptions. The flank honing refines the cutting geometry to reduce burr formation and improve thread fit, which is particularly valuable for internal pipe threads that must seal reliably. These features combine to improve process uptime and deliver threads that meet both mechanical and sealing requirements. Machine integration and material versatility for workshop use The tool offers a 16 mm shank for secure clamping in standard holders and automatic tapping spindles, supporting straightforward integration into existing machining cells. It is suitable for a broad range of materials: general steels, stainless steels, spheroidal (ductile) cast iron and non‑ferrous metals, making it a flexible choice for mixed‑material production environments. The Whitworth pipe form (G 1/2" x 14 tpi) is explicitly designed for pipe‑threaded connections; using the correct tap geometry reduces post‑process inspection and ensures interchangeability with standard pipe fittings. Together, these traits support efficient, repeatable production workflows. Choose the TECWERK machine tap via Metav Werkzeuge for assured Whitworth G thread quality and reliable supply — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific applications Technical data Article number: 2000867956NW Product label: Machine tap DIN 5156C universal G 1/2" x 14 HSS‑Co vap. ISO 228 TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867956NW Core specifications Shank diameter: 16 mm Thread: G 1/2" x 14 tpi Spiral angle: 40° Shank Ø: 16 mm Special features HSS‑Co material Form C universal geometry Vapour‑treated finish Green ring identification Right‑hand spiral 40° Flank‑honed cutting edges Whitworth pipe thread G to DIN ISO 228 Designed for blind‑hole tapping Suitable for steel, stainless steel, ductile cast iron and non‑ferrous metals FAQ What thread form does this tap cut? The TECWERK machine tap cuts a Whitworth pipe thread G 1/2" x 14 tpi in accordance with DIN ISO 228, providing compatibility with standard pipe fittings. Which materials are suitable for machining with this tap? This tap is made in HSS‑Co and is suitable for general steels, stainless steels, spheroidal (ductile) cast iron and most non‑ferrous metals, delivering reliable performance across these materials. Is the tap suitable for blind‑hole threads? Yes, the 40° right‑hand spiral and flute design are optimised for blind‑hole applications, promoting chip evacuation and reducing the risk of breakage. What machine clamping is required for use? The tap has a 16 mm shank, compatible with common collets and holders used in machine tapping spindles and multi‑spindle machines. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a durable, high-performance thread tap that combines cobalt HSS construction with a 40° right-hand spiral for reliable chip evacuation; order or request technical advice via Metav Werkzeuge for assured supply and workshop-ready delivery. Machine Tap DIN 5156C G 1/2" x 14 HSS-Co ISO 228 (TECWERK) — Cobalt high-speed steel, 40° right-hand spiral for blind-hole Whitworth pipe threads The Machine Tap DIN 5156C G 1/2" x 14 HSS-Co ISO 228 (TECWERK) is designed to cut Whitworth pipe threads (G) to DIN ISO 228 in blind holes, offering robust performance in steels and malleable cast iron. Cobalt HSS for extended tool life Right-hand 40° spiral for efficient chip removal Relief-ground flanks for accurate thread form Shank Ø 16 mm for secure toolholding Consistent pipe-thread quality for blind-hole applications This threaded tool is engineered to produce Whitworth pipe threads to DIN ISO 228 with consistent form and fit. The geometry — specified as Form C with relief-ground flanks — maintains the flank profile critical for sealing pipe connections, reducing the need for rework. Intended for blind-hole threads, the design channels chips away from the cutting zone so that thread integrity is preserved even in confined bores, supporting predictable assembly and leak-free joints. Enhanced cutting performance and service life Constructed from HSS-Co (cobalt high-speed steel), the tap offers improved hot hardness and wear resistance compared with standard high-speed steels, extending tool life under continuous production. The 40° right-hand spiral improves chip flow when forming threads in interrupted or difficult cuts; this is particularly beneficial when machining steels up to approximately 1000 N/mm² and malleable cast iron, where reliable chip control reduces downtime. The combination of material and spiral form results in fewer tool changes and steadier cycle times. Practical workshop integration and handling benefits With a shank Ø 16 mm, the tap fits common toolholders and collets, ensuring secure clamping and concentric running for accurate threads. The tap is suitable for use in standard machine-tool setups where ISO 228 pipe threads are required, enabling straightforward integration into production or maintenance schedules. As a trusted distributor and precision partner, Metav Werkzeuge ensures supply continuity and technical consultation, helping workshops maintain throughput while keeping inventory streamlined. Request the TECWERK machine tap through Metav Werkzeuge for dependable thread production and straightforward technical guidance — Metav Werkzeuge in Emmerich can advise on suitability and delivery at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867513NW Label: Maschinengewindebohrer DIN 5156C G 1/2 Zollx14 HSS-Co ISO 228 TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Shank diameter: 16 mm Spiral angle: 40° Thread form: G 1/2" x 14 (Whitworth pipe thread) Material tensile limit: up to ≈ 1000 N/mm² Special features HSS-Co (cobalt high-speed steel) Form C Right-hand 40° spiral with flutes for chip evacuation Relief-ground flanks for precise thread profile Conforms to DIN ISO 228 for Whitworth pipe threads Designed for blind-hole (sackloch) threading Suitable for steels and malleable cast iron FAQ What materials can be machined with this tap? The TECWERK machine tap is suitable for steels up to approximately 1000 N/mm² and for malleable cast iron, as specified for the HSS-Co tool and its geometry. Is this tap suitable for blind-hole thread cutting? Yes, the tool is designed for blind-hole threads; the 40° right-hand spiral supports chip evacuation from confined bores to maintain thread quality. Which thread standard does the tap produce? The tap produces Whitworth pipe threads to DIN ISO 228, specified as G 1/2" x 14 in the product description. How should the tap be held in the machine? Use a rigid, concentric holder compatible with a shank diameter of 16 mm to ensure accurate running and secure clamping during threading operations. Can this tap be used on pre-hardened steels? The data indicates suitability up to steels with tensile strength around 1000 N/mm²; applications involving pre-hardened steels should be assessed against that limit and discussed with Metav Werkzeuge if in doubt. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co construction, ground flanks and a vapourised coating for consistent thread quality and extended tool life; order this tap directly via Metav Werkzeuge or contact our consultants for application advice. Machine tap DIN 5156B Univ. G 1/2" x 14 HSS‑Co — Universal straight‑flute pipe tap by TECWERK The Machine tap DIN 5156B Univ. G 1/2" x 14 HSS‑Co is a universal, straight‑flute pipe tap designed for cutting Whitworth G threads to DIN ISO 228 in through‑hole applications across a wide range of metals HSS‑Co construction for long‑life performance Universal Form B, straight flute design Vapourised coating with green ring identification Ground flanks for improved thread quality Suitable for Whitworth G threads to DIN ISO 228 Consistent cutting performance under industrial loads The combination of HSS‑Co substrate and Form B universal geometry ensures a balance of toughness and wear resistance that favours industrial throughput. Straight flutes provide predictable chip control when producing pipe threads, while ground flanks reduce friction at the cutting edge and improve the dimensional accuracy of each thread. These properties translate into fewer reworks and a steadier production rhythm in demanding workshop environments. Clean through‑threads and reduced rework A dedicated through‑thread chamfer supports fast entry and continuous chip evacuation for through holes, minimising the risk of chip packing that can cause thread damage. The vapourised coating lowers adhesion and improves sliding properties, which helps to preserve edge geometry during repeated cycles. Conformity to Whitworth G threads and DIN ISO 228 guarantees compatibility with standard pipe fittings and eases integration into existing production processes. Broad material compatibility for versatile use The tool is specified for ferrous and non‑ferrous applications, including steel, stainless steel, spheroidal graphite cast iron and non‑ferrous metals, enabling a single tap to cover multiple job types. A 16 mm shank offers robust clamping in standard holders, providing mechanical stability during threading and reducing vibration‑related wear. This versatility reduces tooling inventory and simplifies order management for maintenance and production teams. Designed for reliable workshop integration Robust manufacturing and clear identification (green ring) support quick selection and replacement on crowded tool racks. The combination of robust construction and predictable chip behaviour improves overall tool life, reducing unplanned downtime and contributing to a more economical machining process. Where higher cutting speeds or particularly abrasive alloys are in use, pairing this tap with appropriate lubrication and machine settings extends service intervals and supports consistent throughput. For dependable pipe‑thread production with TECWERK tooling, contact Metav Werkzeuge in Emmerich for supply and application guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867944NW Manufacturer: TECWERK Packaging unit: 1 Numbers / Core technical data Shank diameter: 16 mm Thread specification: G 1/2" × 14 tpi Standard: DIN ISO 228 Designs / Special features Material: HSS‑Co Form: B (universal) Straight fluted Ground flanks Vapourised coating (green ring) Through‑thread cutting chamfer Suitable for steel, stainless steel, spheroidal graphite cast iron, non‑ferrous metals FAQ What thread standard does this tap produce? The TECWERK machine tap produces Whitworth G threads in accordance with DIN ISO 228, specified here as G 1/2" × 14 tpi. Which materials can be machined with this tap? This tap is suitable for steel, stainless steel, spheroidal graphite cast iron and non‑ferrous metals as indicated in the product specification. How is the tap identified on the tool rack? The tap features a vapourised coating with a green ring identification, making it easy to select during tool changes. What shank size is required for clamping? A 16 mm shank is specified; the tap is designed for secure clamping in standard collets and holders compatible with that diameter. Is this tap intended for through or blind holes? The tool includes a cutting chamfer for through threads and is optimised for through‑hole applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Combine the high wear resistance of HSS‑Co with precise Whitworth pipe threading and a 40° right‑hand spiral to achieve consistent, clean threads in blind holes; order the tool easily through Metav Werkzeuge or consult our advisors for application guidance. Machine tap DIN 5156C — Whitworth pipe thread G 1/4" × 19, HSS‑Co (TECWERK) The Machine tap DIN 5156C is a universal threading tool designed for producing Whitworth pipe threads to DIN ISO 228 in blind holes, suitable for a wide range of steels and non‑ferrous materials. HSS‑Co cobalt high‑speed steel construction Whitworth pipe thread G 1/4", 19 tpi Vapourised finish with green ring marking 40° right‑hand spiral, flank‑ground for blind holes Consistent pipe-thread quality for production use Manufactured in HSS‑Co (cobalt high‑speed steel) and built to Form C (universal) geometry, this threading tool delivers stable cutting performance and extended service life in intermittent and continuous work. The tap is designed to machine Whitworth pipe thread G 1/4" to DIN ISO 228, a standardised form that reduces rejection rates and simplifies inspection in serial production. By combining robust material choice with standard conformity, the tool reduces downtime from frequent replacements and supports reproducible results across batches. Faster cycles and improved chip control for blind holes A 40° right‑hand spiral combined with flank‑ground flutes promotes controlled chip formation and smooth evacuation when working in blind holes, lowering the risk of chip packing and thread damage. The vapourised finish adds surface resilience and eases chip flow, which contributes to faster cycle times and fewer rejected parts. Explained simply, the spiral helix guides swarf away from the cutting edge so tapping requires fewer retracts and less manual cleaning—clear efficiency gains in workshop and production settings. Versatile machining across common workshop materials The tool is rated for machining steel, stainless steels, spheroidal graphite cast iron and non‑ferrous metals, making it a flexible choice for maintenance departments and job shops. The shank diameter of 11 mm ensures secure clamping in standard holders and reduces run‑out, supporting precise thread form even under moderate spindle speeds. Where material variability is a concern, the universal geometry and cobalt alloy composition provide both toughness and hardness to tolerate varied cutting conditions without frequent tool changes. Standard compliance and reduced rework risk Conformity to DIN ISO 228 and the use of the Whitworth pipe thread form ensure compatibility with existing fittings and piping systems, cutting inspection time and eliminating trial‑and‑error adjustments. The green ring marking and vapourised treatment serve as quick visual identifiers for tool selection on the trolley, while the universal specification and HSS‑Co construction offer a balanced compromise between cutting performance and robustness. For operations focused on repeatability and minimising scrap, these characteristics support a predictable production flow. Choose TECWERK’s machine tap for reliable, standardised pipe threading and contact Metav Werkzeuge for application advice and fast supply from Emmerich — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: 2000867954NW Brand: TECWERK Packaging unit: 1 UID: 2000867954NW Facts Size: G 1/4" (Whitworth pipe thread) Thread count: 19 tpi Shank diameter: 11 mm Spiral helix angle: 40° Special features Material: HSS‑Co (cobalt high‑speed steel) Form: C (universal) Finish: vapourised, green ring marking Flute/geometry: flank‑ground Direction: right‑hand spiral Thread standard: DIN ISO 228 (Whitworth pipe thread) Application: for blind holes Suitable materials: steel, stainless steels, spheroidal cast iron, non‑ferrous metals FAQ What thread form and standard does this tap produce? The tap produces Whitworth pipe thread G 1/4" to DIN ISO 228, ensuring compatibility with standard BSPP fittings and assemblies. Is the tool suitable for stainless steel and cast iron? Yes, the HSS‑Co construction and universal form make the tap suitable for stainless steels and spheroidal graphite cast iron as well as other non‑ferrous metals. How does the 40° spiral help when tapping blind holes? The 40° right‑hand spiral promotes chip evacuation into the flutes, reducing the risk of chip compacting at the thread root in blind holes and improving surface finish. What shank size is required for mounting the tap? The tap has a shank diameter of 11 mm, compatible with standard collets and holders that accept this shank size. Is the finish of the tool treated for improved wear resistance? The tool features a vapourised finish and green ring marking, which enhance surface durability and help with quick tool identification. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

High wear resistance from HSS‑Co, universal Form B geometry and a straight‑fluted design ensure consistent, machine‑ready thread production for Whitworth pipe fittings; ideal for mixed batch work. Order through Metav Werkzeuge or consult our specialists for suitability and delivery. TECWERK machine tap G 1/4" x 19 tpi (DIN 5156B) — HSS‑Co, universal The TECWERK machine tap G 1/4" x 19 is a universal Form B machine tap designed for producing Whitworth pipe threads (G) to DIN ISO 228 in steels, stainless steels, spheroidal cast iron and non‑ferrous metals. HSS‑Co alloy for enhanced wear resistance Universal Form B geometry for machine use Straight flutes with relief‑ground flanks Suitable for steel, stainless steel and non‑ferrous metals Durable alloy and geometry for high uptime Constructed from HSS‑Co (cobalt‑alloy high‑speed steel), the tool combines hardness with toughness to resist wear under repeated cycle use. The Form B geometry is optimised for machine tapping and helps maintain thread accuracy over longer production runs, reducing tool change frequency. The vapour‑treated surface and the green ring identification speed up handling in busy workshops while contributing to corrosion resistance and easier inventory recognition. Reliable pipe threads that meet standards The tool cuts Whitworth G threads in accordance with DIN ISO 228, delivering parallel pipe threads suited to a wide range of hydraulic and pneumatic fittings. A dedicated cutting chamfer for through threads ensures clean chip evacuation and consistent start‑up, which translates into fewer rejects and lower rework. For applications where joint reliability matters, this geometry provides predictable, repeatable thread form suitable for assembly with common sealing methods. Machine compatibility for efficient production With a shank Ø 11 mm and straight‑fluted design, the tap is built for machine spindles and automated tapping units. Straight flutes and relief‑ground flanks promote smooth chip flow and lower tapping torque, enabling faster cycle times and reducing strain on tap holders. The tool’s universal character makes it suitable for mixed‑material batches, helping streamline tooling choices across varied workpieces. Clear identification and material versatility Marked for quick recognition, the tool is intended for use in steel, stainless steel, spheroidal cast iron and non‑ferrous metals, covering most workshop requirements for pipe‑threaded connections. The specification 1/4" x 19 tpi matches common Whitworth pipe sizes; the combination of material choice and design gives a balance between cutting performance and component finish, ensuring dependable thread quality even in repetitive operations. Choose TECWERK machine taps for consistent, industrial‑grade thread production and contact Metav Werkzeuge in Emmerich for tailored advice, availability and secure supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000867942NW Item: Machine tap G 1/4" x 19 tpi, DIN 5156B Manufacturer: TECWERK Packing unit: 1 UID: 2000867942NW Facts Shank diameter: 11 mm Thread: G 1/4" × 19 tpi Standard: DIN ISO 228 Special features Material: HSS‑Co (cobalt high‑speed steel) Form B, type universal Vapour‑treated coating Green ring identification Straight flutes Relief‑ground flanks Cutting chamfer for through threads Suitable for steel, stainless steels, spheroidal cast iron, non‑ferrous metals FAQ What thread standard does this tap produce? The tap produces Whitworth G threads in line with DIN ISO 228, suitable for standard pipe connections and fittings. Which materials can be machined with this tool? The TECWERK tap is specified for steel, stainless steel, spheroidal cast iron and non‑ferrous metals, offering broad application across workshop and industrial parts. What does the green ring signify? The green ring is a visual identifier for the vapour‑treated, machine‑grade variant and assists with rapid tool selection in multi‑tool environments. Is the tap suitable for machine tapping units? Yes — the universal Form B geometry, straight flutes and shank Ø 11 mm make the tool compatible with standard machine spindles and tapping holders for efficient production. What are the key cutting features for through threads? The tap includes a dedicated cutting chamfer for through threads that promotes clean chip evacuation and consistent thread starts for reduced rework. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of cobalt HSS construction, vapour coating and a 40° helix for reliable chip control and long tool life; order the TECWERK machine tap directly via Metav Werkzeuge or request technical advice from our specialists. TECWERK machine tap DIN 5156C — HSS‑Co, Whitworth G 1/8" x 28 tpi A TECWERK machine tap DIN 5156C engineered as a universal-form tapping tool for producing Whitworth pipe threads G in blind-hole applications across common industrial materials. Cobalt high‑speed steel (HSS‑Co) core Vapour‑coated finish, green ring Right‑hand 40° helix for chip control Designed for blind‑hole Whitworth threads Extended tool life and consistent cutting performance The combination of HSS‑Co material and a vapour‑coated surface provides superior wear resistance compared with standard high‑speed taps. This material pairing reduces flank wear and preserves the cutting geometry over longer production runs, which translates into fewer tool changes and improved uptime. The form C (universal) design balances cutting action and robustness, making the tool suitable for mixed batch production where both life and thread quality matter. Reliable threads in blind‑hole Whitworth applications Optimised for Whitworth pipe thread G profiles to DIN ISO 228, this tapping tool produces precise internal threads even in blind‑hole situations. The right‑hand 40° helix promotes controlled chip formation and evacuation toward the flanks, reducing the risk of chip packing in interrupted or deep blind holes. The result is consistent thread form and surface finish, especially important where leak‑tight joints or sealed connections are required. Compatibility with common workshop setups and materials With a 7 mm shank, the tap integrates easily into standard machine holders and spindle adaptors used across small to medium CNC tapping centres and tapping heads. The tool is specified for machining steel, stainless steel, spheroidal graphite cast iron and non‑ferrous metals, so the same part can be relied upon across a variety of components. The universal geometry simplifies tool selection for mixed‑material work, reducing inventory complexity on the shop floor. Practical advantages for production planning The chamfered and flank‑ground cutting edges deliver predictable entry behaviour and promote repeatable cycle times on automated lines. Clear, measurable properties such as material grade (HSS‑Co), helix angle and compliance with the DIN ISO 228 standard support process documentation and quality control. Specifying a standardised tool like this helps streamline procurement and ensures interchangeability across machines, which aids maintenance scheduling and reduces unexpected downtime. For assured thread quality and dependable supply of the TECWERK HSS‑Co machine tap, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for ordering and technical assistance Technical Data Article number: 2000867953NW SKU: 2000867953NW Name: Maschinengewindebohrer DIN 5156C Univ.G 1/8" x 28 HSS‑Co vapourised TECWERK Packaging unit: 1 Manufacturer: TECWERK Facts Shank diameter: 7 mm Thread form: G 1/8" x 28 tpi Standard: DIN ISO 228 Special features Material: HSS‑Co (cobalt high‑speed steel) Coating: vapour‑coated (green ring) Type: Universal, Form C Helix: right‑hand 40° Cutting edge: flank ground Application: blind‑hole threads Suitable for: steel, stainless steel, spheroidal cast iron, non‑ferrous metals FAQ What thread standard does this tap produce? The tap produces Whitworth pipe threads to DIN ISO 228 specification, suitable for G‑type fittings and connections. Is the tool suitable for blind holes? Yes, the tap is designed for blind‑hole threading and the right‑hand 40° helix aids chip control in confined spaces. Which materials can be machined with this tap? This HSS‑Co tap is specified for steel, stainless steel, spheroidal cast iron and non‑ferrous metals as listed in the product data. What is the shank size and how does it integrate with holders? The tool has a 7 mm shank, compatible with common collets and adaptors used in small to medium tapping heads and machines. Who supplies this tool and where can it be ordered? The tool is offered by TECWERK and is available through Metav Werkzeuge; refer to the SKU 2000867953NW when enquiring. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a versatile HSS‑Co construction and straight‑fluted geometry for reliable Whitworth pipe-threading; the robust relief‑ground flanks and through‑thread chamfer support continuous production. Order the TECWERK tap directly via Metav Werkzeuge or consult our specialists if further technical details are required. TECWERK Machine Tap G 1/8" x 28 – HSS‑Co, Form B (Universal) The TECWERK machine tap G 1/8" x 28 is a universal Form B tap engineered for producing parallel Whitworth pipe threads (G) in through‑hole applications across a wide range of metals HSS‑Co straight‑fluted cutting geometry Parallel Whitworth pipe thread G to DIN ISO 228 Relief‑ground flanks for improved wear resistance Through‑thread chamfer for clean chip evacuation Reliable pipe‑thread production for mixed materials The universal Form B design combines a robust cutting profile with a cobalt high‑speed steel (HSS‑Co) body to create a balance between toughness and edge retention. This geometry supports consistent thread form on parallel Whitworth pipe threads, specified to DIN ISO 228, so mating components assemble precisely. For manufacturing environments where different materials appear in the same production run, this configuration reduces tool changeovers and simplifies tooling lists, contributing directly to higher throughput and fewer interruptions. Reduced risk of tap failure and clearer chips The straight‑fluted design, paired with relief‑ground flanks, improves cutting stability and reduces radial loads during tapping. The incorporated through‑thread chamfer is intended for through holes and aids chip formation and evacuation, lowering the chance of clogging and breakage in continuous operations. These features collectively lead to longer tool life and fewer rejects, supporting a measurable improvement in operational reliability and machining economics. Practical compatibility and handling in the shop Marked with a green identification ring and supplied with a 7 mm shank, the tool fits common collets and holders found in workshop and machine‑tool setups. The tap is suitable for steel, stainless steel, spheroidal cast iron and non‑ferrous metals, enabling a single tool to cover many typical maintenance and production tasks. The familiar shank diameter simplifies storage and sorting in tool cabinets, while the universal style ensures straightforward replacement in multi‑station environments. Clarity for purchasing and integration Specification‑centred procurement benefits from clear standard references: DIN 5156B and DIN ISO 228 designate the manufacturing and thread form expectations, which assists planning for quality control and assembly. The HSS‑Co material choice supports higher cutting temperatures and improved wear resistance compared with standard high‑speed grades, reducing consumable costs over time. For customers seeking straightforward integration into existing processes, this tap provides a predictable, durable option without requiring specialised equipment. For dependable Whitworth pipe‑thread tapping with TECWERK quality, contact Metav Werkzeuge in Emmerich for ordering and tailored advice; Metav’s specialists can confirm suitability for specific materials and production requirements. Technical data Article number: 2000867941NW Manufacturer: TECWERK Label: Maschinengewindebohrer DIN 5156B Univ.G 1/8 Zollx28 HSS‑Co vap.ISO 228 TECWERK Facts Thread: G 1/8" × 28 tpi Shank Ø: 7 mm Pack unit: 1 Special features HSS‑Co (cobalt high‑speed steel) Form B, universal tapping type Vapourised surface treatment, green ring identification Straight‑fluted geometry Relief‑ground flanks Parallel Whitworth pipe thread G per DIN ISO 228 Through‑thread chamfer for through holes Suitable for steel, stainless steel, spheroidal cast iron and non‑ferrous metals FAQ What thread form does this tap produce? The tool produces parallel Whitworth pipe threads G in accordance with DIN ISO 228, making it suitable for standard pipe‑fitting applications. Which materials can be machined with this tap? This TECWERK machine tap is specified for steel, stainless steel, spheroidal cast iron and non‑ferrous metals, offering broad material compatibility for general workshop use. What is the shank diameter and how is the tool identified? The tap has a shank diameter of 7 mm and features a green identification ring to simplify selection and storage. Is this tap suitable for through‑hole threads? Yes, the tap includes a through‑thread chamfer specifically intended for clean chip evacuation in through‑hole applications. Which standards describe the tool and thread? The tap corresponds to DIN 5156B for the tool form and to DIN ISO 228 for the Whitworth pipe‑thread G specifications. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of reliable HSSE cutting performance, a secure 6.3 mm (1/4") HexDrive shank and ISO-class thread tolerance for consistent, production-ready thread quality; order directly via Metav Werkzeuge or contact the consultants for application advice. Maschinengewindebohrer-Bit HSSE M10 × 8.50 mm, pitch 1.50 mm – Machine tap bit with HexDrive and HSS-Co Maschinengewindebohrer-Bit HSSE M10 × 8.50 mm, pitch 1.50 mm is a machine tap bit designed for producing metric ISO threads in blind holes, combining a cobalt-alloy high-speed steel cutting material with a 6.3 mm (1/4") hex shank for secure drive engagement HexDrive with 6.3 mm (1/4") hex shank HSSE (HSS-Co) for improved wear resistance Form C (15° RSP) — DIN 371 specification Metric ISO M10 thread, tolerance ISO2 (6H) Reliable thread creation in confined bores The bit delivers consistent metric ISO threads for blind-hole applications thanks to its Form C (15° RSP) geometry, which controls chip removal and reduces the risk of chip packing. Manufactured from HSSE (HSS-Co), the tool maintains cutting edge stability under intermittent loads; this translates into fewer rejects and predictable cycle times on machining centres. The provided pitch and thread geometry are held to ISO2 (6H) tolerance, supporting interchangeability with standard fasteners and ensuring dependable assembly fit. Durable construction for demanding materials The combination of a cobalt-enriched high-speed-steel substrate and the specified geometry provides improved resistance to abrasion and thermal softening during thread forming. Rated for use in materials with tensile strengths up to 900 N/mm², the bit is suitable for unalloyed and low-alloy steels encountered in general engineering. The HexDrive shank design secures power transmission from the spindle or driver, reducing slippage and tool wear, which contributes to extended service life and lower total tooling costs. Standards and production compatibility Conformance to DIN 371 (WN) ensures that the tool integrates smoothly into established machining processes and inspection routines. The 6.3 mm (1/4") hex shank offers compatibility with quick-change holders and drill chucks commonly found in production cells, making changeovers straightforward and reducing downtime. The nominal length of 100 mm and the specified threaded length provide clear installation and depth-control data for cycle planning and quality documentation. Practical benefits for workshop and shop-floor use Chip control and the Form C profile ease use in blind holes, decreasing the need for secondary cleaning operations. The design suits high-repetition environments and repair work where repeatable thread quality is essential. For purchasing and logistics, the compact single-unit packaging simplifies inventory management while the tool’s robustness supports predictable replenishment intervals when combined with a Metav procurement strategy. For application advice or to secure this HSSE machine tap bit for production use, contact Metav Werkzeuge for specialist guidance and immediate order processing via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 4000868084NW Manufacturer: VÖLKEL GmbH Type: Machine tap bit HSSE M10 × 8.50 mm, pitch 1.50 mm Facts Length: 100 mm Shank: 6.3 mm (1/4") hex Thread tolerance: ISO2 (6H) Rated material strength: up to 900 N/mm² Special features HexDrive HSSE (HSS-Co) cutting material Form C (15° RSP) Metric ISO thread, suited for blind holes Standard: WN (DIN 371) FAQ What thread size and pitch does this tap bit produce? This machine tap bit produces an M10 metric ISO thread with a 1.50 mm pitch, held to the ISO2 (6H) tolerance class. Is the shank compatible with quick-change holders? Yes, the 6.3 mm (1/4") hex shank (HexDrive) is suitable for standard quick-change holders and chucks used in production environments. Which materials can be machined with this tool? The tool, made from HSSE (HSS-Co), is intended for unalloyed and low-alloy steels and is specified for work up to 900 N/mm² tensile strength. Can the tap bit be used for blind-hole threading? Yes, the geometry is designed for blind holes, with Form C (15° RSP) aiding chip control and reducing the risk of chip blockage. Which standard does the tool conform to? The bit is manufactured to the WN (DIN 371) specification, supporting standardised production and inspection procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the HSSE cutting material, the quick-change 6.3 mm hex shank and the ISO2 (6H) thread tolerance for consistent M10 thread quality in general-purpose steel applications; order the machine tap bit directly via Metav Werkzeuge or request technical advice from our consultants. Machine tap bit HSSE M10 x 8.50 mm, pitch 1.50 mm — VÖLKEL with 6.3 mm HexDrive shank The machine tap bit HSSE M10 x 8.50 mm, pitch 1.50 mm — VÖLKEL is a dedicated machine tap for producing metric M10 through-threads in unalloyed and low-alloy steels up to 900 N/mm², designed for use in power holders with a 6.3 mm (1/4") hex drive HexDrive 6.3 mm (1/4") hex shank HSSE cutting material for wear resistance Metric ISO M10 thread, tolerance ISO2 (6H) Peel-cut geometry for clean through-threads Improved process reliability through durable HSSE construction The HSSE composition ensures higher hot hardness and improved wear resistance compared with conventional high-speed steels; this means longer life and more consistent thread profiles in continuous production. The HSSE cutting material, combined with the Form B geometry, reduces edge wear under elevated temperatures, which supports predictable tool-change intervals and less frequent regrinding. For operations where throughput and repeatability matter, a tool with enhanced heat resistance translates directly into fewer interruptions and steadier output. Faster changeovers and secure clamping for production environments Equipped with a 6.3 mm (1/4") hex shank, the tap bit is compatible with standard HexDrive quick-change holders and power tool chucks, allowing rapid tool exchange and reduced set-up times. The hex shank improves torque transmission, minimising slippage in high-torque tapping cycles. The metric ISO thread specification and ISO2 (6H) tolerance ensure interchangeability with standard fasteners and gauges, supporting consistent assembly fitment across batches and simplifying quality control. Cleaner chips and superior thread quality for through-holes The integrated peel-cut geometry (Schälanschnitt) is engineered to produce predictable chip formation when machining through-threads, promoting efficient evacuation and lowering the risk of chip packing. This results in improved surface finish and thread form, particularly in unalloyed and low-alloy steels up to 900 N/mm². The compliance with WN (DIN 371) and the Form B design offers a balanced compromise between cutting strength and chip control, suitable for general-purpose workshop and industrial applications. Standards, dimensions and recommended applications The tap bit follows established industry standards and comes in a 100 mm overall length, making it suitable for a wide range of machine tapping setups. The M10 thread with a 1.50 mm pitch is a common metric size for mechanical assemblies; using a tool that adheres to recognised tolerances and forms reduces rework and supports consistent assembly quality. Typical users include maintenance departments, toolrooms and production lines requiring robust, repeatable M10 threads in readily machinable steels. For stable M10 thread production consider the VÖLKEL machine tap bit and contact Metav Werkzeuge GmbH in Emmerich for tailored technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 4000868077NW Label: Maschinengewindebohrer-Bit HSSE 10 M10x8,50mm Steig.1,50mm VÖLKEL Manufacturer: VÖLKEL GmbH Packaging unit: 1 Facts Length: 100 mm Shank: 6.3 mm (1/4") Thread: M10 Pitch: 1.50 mm Tolerance: ISO2 (6H) Material tensile strength (suitable for): up to 900 N/mm² Special features Cutting material: HSSE (HSS-Co) Design: Form B Standard: WN (DIN 371) Drive: HexDrive 6.3 mm (1/4") hex shank Geometry: peel-cut for through-threads Application: general use in unalloyed and low-alloy steels FAQ Which materials can be machined with this tap bit? The VÖLKEL machine tap bit is designed for general use in unalloyed and low-alloy steels and is rated for materials up to 900 N/mm² tensile strength. Is the tool suitable for producing through-threads? Yes — the tap bit features a peel-cut geometry specifically for through-threads, which aids chip evacuation and improves thread quality. What drive connection is required for the tap bit? A 6.3 mm (1/4") HexDrive quick-change holder or chuck is compatible with the tap bit’s hex shank, enabling secure clamping and fast tool changes. Which standards and tolerance classes apply? The tool conforms to WN (DIN 371) standards and produces metric M10 threads to the ISO2 (6H) tolerance class. What are the overall length and intended thread size? Overall length is 100 mm; the tool cuts M10 threads with a 1.50 mm pitch and is intended for common industrial and workshop applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a high‑performance combination of HSS‑Co material and a vapour‑deposited coating for extended tool life and consistent fine‑thread quality; the right‑hand spiral 40° and flank‑honed geometry ensure reliable blind‑hole tapping. Order the tool directly via Metav Werkzeuge or consult the Metav team for machining recommendations. TECWERK machine tap MF10×1 mm — HSS‑Co, vapour‑deposited, DIN 374C The TECWERK machine tap MF10×1 mm (DIN 374C, HSS‑Co) is a universal machine tap engineered for accurate metric fine threads in blind holes across steels and non‑ferrous alloys HSS‑Co for high wear resistance Right‑hand spiral 40° for blind holes ISO metric fine thread MF10×1 mm Shank Ø 7 mm for secure clamping Consistent thread accuracy for fine metric applications The design follows DIN 374C and the tap is manufactured for MF10×1 mm metric fine threads with tolerance ISO2 (6H), which translates into repeatable fits in serial production. The use of HSS‑Co (cobalt high‑speed steel) provides a balance between toughness and hot‑hardness, reducing wear in interrupted cuts. The vapour‑deposited coating—indicated by the green ring—improves surface hardness and sliding properties, allowing longer tool life and fewer rejects when producing precision threads in high‑volume workflows. Geometry and coating that reduce downtime and improve thread quality A right‑hand spiral 40° geometry is optimised for blind‑hole threads, evacuating chips away from the cutting edge and minimising the risk of chip jamming. The flanks are flank‑honed, which improves thread flank contact and reduces burr formation; this results in better thread class and less post‑processing. The combination of spiral geometry and coating reduces cycle interruptions, supporting faster throughput and more predictable machining times in mixed‑material environments. Material range and clamping for reliable results Suitable workpiece materials include steel, stainless steels, spheroidal cast iron and non‑ferrous metals, making the tool versatile for maintenance shops and production lines alike. The shank Ø 7 mm provides secure clamping in standard toolholders, ensuring concentricity and lower runout during machining. For best outcomes, select cutting parameters consistent with high‑speed cobalt taps and ensure coolant or internal lubrication is applied for tougher alloys; this approach extends tool life and maintains the required ISO2 (6H) tolerance without sacrificing productivity. Contact Metav Werkzeuge for tailored cutting data, availability and order processing — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance and fast delivery from Emmerich. Technical Data Article number: 2000867922NW Product label: Maschinengewindebohrer DIN 374C Univ.MF10x1mm HSS-Co vap.6H TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867922NW Data Thread size: MF10×1 mm Shank diameter: 7 mm Spiral angle: 40° Tolerance: ISO2 (6H) Standard: DIN 374C Special features Material: HSS‑Co (cobalt high‑speed steel) Coating: vapour‑deposited (green ring) Form: C, universal type Right‑hand spiral 40° Flank‑honed cutting edges Intended for blind‑hole threads Suitable for steel, stainless steels, spheroidal cast iron, non‑ferrous metals FAQ What thread size does this tap produce? The TECWERK machine tap produces an MF10×1 mm metric fine thread, manufactured to DIN 374C with tolerance ISO2 (6H) for consistent fits. Is the tap suitable for stainless steel? Yes — the tool’s HSS‑Co composition and vapour‑deposited coating make the tap suitable for stainless steels as well as general steel and non‑ferrous metals. Can this tap be used for blind holes? The tap is designed specifically for blind‑hole threads, featuring a right‑hand spiral 40° that helps evacuate chips from the hole bottom. What clamping diameter is required? The shank diameter is 7 mm, compatible with standard collets and holders that provide secure clamping and low runout. How does the coating affect performance? The vapour‑deposited coating increases surface hardness and reduces friction, extending tool life and improving thread quality under production conditions. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of precise ISO‑tolerance threading and robust cobalt high‑speed steel performance for reliable production results; the combination of a nitrided, vapour‑deposited surface and straight‑flute geometry ensures extended tool life and consistent chip evacuation. Order the machine tap directly via Metav Werkzeuge or consult our specialists for application advice. Machine tap DIN 371B VA M10×1.5 HSS‑Co, nitrided & vapour‑deposited, 6H (TECWERK) The Machine tap DIN 371B VA M10×1.5 HSS‑Co is a straight‑fluted industrial tap engineered for through‑hole metric threading in high‑strength, corrosion‑resistant and heat‑resistant steels. HSS‑Co high‑performance cutting steel Nitrided and vapour‑deposited coating Straight flutes with ISO2 (6H) tolerance Consistent thread accuracy for assembly reliability The tap delivers ISO2 (6H) tolerance and conforms to DIN 13 Sheet 1, providing a predictable fit for metric fastenings and reducing rework in serial production. Because the geometry and tolerance class are aligned with international standards, the tool supports reliable assembly processes and interchangeability of threaded parts. The applied tolerance class means threads meet tighter dimensional limits than ordinary taps, which is especially important where gasket seating or press‑fit alignment is required. This precision contributes directly to lower scrap rates and fewer rejects across repetitive machining tasks. Enhanced tool life through advanced materials and surface treatment Manufactured from HSS‑Co (cobalt high‑speed steel) and finished by nitriding and vapour deposition, the cutting edges resist wear and retain hardness under thermal load. The surface treatment improves resistance to adhesion and micro‑welding when cutting stainless and heat‑resistant steels, extending cutting intervals between tool changes. The blue identification ring simplifies tool management on the shop floor. These material and coating choices yield a cost‑effective balance between cutting performance and lifetime, translating into fewer tool changes and more predictable production planning. Geometry optimised for through‑hole threading and chip control The straight‑flute design combined with a purpose‑made shear cutting chamfer for through threads encourages controlled chip formation and evacuation in long through‑hole operations. Flanks that are relief‑ground reduce friction and the risk of seizing in sticky stainless alloys, while the shank profile supports stable engagement in machine holders. For machine tapping setups, this geometry helps maintain spindle load stability and reduces the likelihood of tap breakage, making the tool suitable for series machining where repeatability is essential. Applications, handling and process integration Suitable for machining corrosion‑resistant, acid‑resistant and heat‑resistant steels with tensile strengths above 850 N/mm², this tap supports demanding alloys commonly used in chemical, energy and high‑temperature components. The tool is intended for machine tapping operations and features a shank diameter of 10 mm for direct mounting or adapter use in standard tool holders. For process planning, the tap’s construction allows predictable tool life and machining parameters, aiding cycle time calculations and reducing downtime. If uncertainties remain about compatibility with a specific alloy or machine, Metav’s technical advisers can supply cutting data and application guidance. For TECWERK quality in stainless and heat‑resistant steel threading, contact Metav Werkzeuge in Emmerich for tailored technical advice and reliable supply. Technical data Article number: 2000867210NW Brand: TECWERK Packaging unit: 1 Shank Ø: 10 mm Facts Thread: M10×1.5 Standard: DIN 13 Sheet 1 (metric ISO) Tolerance: ISO2 (6H) Material strength application: >850 N/mm² Special features Material: HSS‑Co Coating: nitrided and vapour‑deposited Flute: straight flutes Chamfer: shear cutting chamfer for through threads Flank treatment: relief‑ground flanks Identification: blue ring Application: stainless, acid‑resistant and heat‑resistant steels FAQ What materials is the tap suitable for? The tap is designed for corrosion‑resistant, acid‑resistant and heat‑resistant steels, and is specified for use with materials of tensile strength above 850 N/mm². Is this tool suitable for machine tapping rather than hand tapping? Yes, the TECWERK machine tap is intended for machine use; the 10 mm shank supports secure clamping in standard machine holders. What standard and tolerance does the tap meet? The machine tap conforms to DIN 13 Sheet 1 for metric ISO threads and is manufactured to the ISO2 tolerance class (6H) for precise thread fit. How does the surface treatment benefit production? The nitrided and vapour‑deposited finish reduces wear and adhesive build‑up when tapping stainless and heat‑resistant steels, improving tool life and process stability. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a robust combination of material strength and precise thread tolerance to ensure consistent fine-thread production. The HSS‑Co construction and vapour coating deliver durable cutting performance while the ISO 6H tolerance and DIN 13 compliance secure interchangeability in serial manufacture. Order the TECWERK tool via Metav Werkzeuge or contact our technical advisers for machining recommendations. Machine tap DIN 374B, MF10×1 mm — HSS‑Co, vapour-coated (TECWERK) A Machine tap MF10×1 mm for producing metric fine threads in a wide range of engineering materials using standard machine holders. HSS‑Co high-speed steel Vapour-coated for wear resistance Straight flute with relieved flanks Metric fine thread MF, ISO 6H tolerance Consistent fine-thread quality through material and tolerance control The combination of HSS‑Co construction and ISO 6H tolerance makes this threading tool suitable for industrial production where repeatability matters. Cobalt-alloyed high-speed steel maintains hardness at elevated cutting temperatures, which improves tool life under continuous operation. The declared tolerance class ensures that threads conform to DIN 13 and remain interchangeable across assemblies, supporting reliable component fit in serial production. Geometry engineered for clean thread profiles and process reliability A straight flute design together with flank relief reduces radial forces and helps to guide chips away from the cutting zone, particularly when cutting through holes. The Form B universal geometry balances cutting action and robustness, and the included chamfer for through threads supports easy thread entry and exit. These features combine to lower scrap rates and to produce clean thread flanks with consistent profile control. Broad material suitability for workshop and production use Designed for use on steel, stainless steels, spheroidal graphite cast iron and non‑ferrous metals, this tap addresses a wide range of workshop requirements. The vapour coating increases surface hardness and aids wear resistance across materials, extending effective service life in mixed‑material batches. Its compatibility with standard machine holders simplifies integration into machining centres and reduces setup time. Integration, handling and supply-chain confidence With a shaft Ø 7 mm, the tool fits many common machine holders used in production and maintenance environments. Supplied in single units for controlled usage, the threading tool is an efficient option when one-off replacements or small batch runs are required. Metav’s quality filter in Emmerich and established supply logistics support dependable delivery and technical backup, helping to keep production running smoothly. For precise fine-thread machining with TECWERK HSS‑Co taps, contact Metav Werkzeuge for ordering and tooling advice — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application details and stocking options Technical Data Article number: 2000867651NW Name: Machine tap DIN 374B MF10×1 mm HSS‑Co vapour-coated TECWERK Packaging unit: 1 Data Thread: MF10×1 mm Shaft diameter: 7 mm Tolerance field: ISO2 (6H) Special features Material: HSS‑Co Form: B, universal Coating: vapour-coated Straight fluted; flanks relieved Green ring identification Standard: DIN 13 For: steel, stainless steel, spheroidal graphite cast iron, non‑ferrous metals With chamfer for through threads FAQ What materials is this tap suitable for? The TECWERK machine tap MF10×1 mm is suitable for steel, stainless steels, spheroidal graphite cast iron and non‑ferrous metals as specified in the technical description. What does the vapour coating provide? The vapour-coated surface on the TECWERK tap improves wear resistance and helps maintain cutting performance over extended machining runs. What does ISO 6H tolerance mean for production? ISO 6H (ISO2) denotes the tolerance field for the internal metric fine thread; it ensures consistent fit and interchangeability when producing MF10×1 mm threads to DIN 13 standard. Can this tap be used for through-hole threads? Yes, the tool includes a chamfer designed for through threads to facilitate clean thread entry and exit in through‑hole applications. Which machine holder fits the tap shaft? The tap has a shaft diameter of 7 mm and is intended to be used with compatible machine holders that accept a 7 mm shank. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

A robust HSS-Co machine tap in Form C with a 40° right-hand spiral and tolerance 6H provides reliable chip evacuation and repeatable thread quality; order the MF10×1.25 mm machine tap via Metav Werkzeuge or consult our specialists for integration advice. Machine tap DIN 374C MF10×1.25 mm HSS-Co 6H — TECWERK Machine tap DIN 374C MF10×1.25 mm HSS-Co 6H is a high-performance tap for producing metric fine threads in blind holes across steels and long‑chip non-ferrous metals. HSS-Co Form C construction Right-hand 40° spiral for chip evacuation Tolerance field 6H for precise fit Shank Ø 7 mm for secure clamping Faster, repeatable thread production with industrial accuracy The MF10×1.25 mm machine tap, built to DIN 374C and featuring HSS‑Co material, combines hardness and toughness for machining steels up to approximately 1000 N/mm². The tolerance 6H ensures a consistent thread fit in production environments, reducing rework and inspection time. Because the flanks are relief ground, the cutting geometry maintains dimensional stability during repetitive runs. This precision-focused design translates into measurable process benefits: higher first-pass yield and fewer thread repairs in mixed‑batch manufacturing. Reduced stoppages thanks to controlled chip flow in blind holes A defining advantage of this tooling is the 40° right‑hand spiral, which actively directs chips away from the cutting edge when machining blind holes. For components made from long‑chip aluminium alloys and similar non‑ferrous metals, that spiral geometry prevents clogging and minimises tap breakage. The combination of spiral form and flank relief lowers torque peaks and promotes smoother tool engagement, so cycle times become more predictable and tool life extends under standard cutting conditions. Robust clamping and seamless machine integration for workshop use With a shank diameter of 7 mm, the tap is compatible with common collet and chuck systems used in production tapping heads and CNC turret stations. The Form C geometry and cobalt alloy base material provide a good balance between wear resistance and fracture toughness, suitable for industrial workshops and jobbing shops alike. When paired with correct speeds and feeds, this tap offers dependable thread quality and repeatable results across different batches and operators, supporting efficient workflows on modern machine tools. For procurement or technical advice regarding the TECWERK MF10×1.25 mm machine tap, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations and immediate availability. Technical data Article number: 2000867484NW Product name: Machine tap DIN 374C MF10×1.25 mm HSS-Co 6H TECWERK Manufacturer: TECWERK Packaging unit: 1 Core specifications Thread: MF 10 × 1.25 mm Standard: DIN 374C / DIN 13 Material: HSS-Co Spiral angle: 40° right-hand Tolerance field: 6H Shank diameter: 7 mm Application: blind holes Workpiece strength: up to ≈1000 N/mm² Special features Form C geometry Flanks relief ground Metric ISO fine thread Suitable for steels, malleable cast iron, long‑chip non‑ferrous metals Designed for machine tapping operations FAQ What materials can be machined with this tap? The TECWERK machine tap MF10×1.25 mm is suitable for steels up to around 1000 N/mm², temper cast iron and long‑chip non‑ferrous metals. Is the tap suitable for blind‑hole threading? Yes, the tool is designed specifically for blind holes, with a 40° spiral to aid chip evacuation and reduce the risk of jamming. What does tolerance 6H imply for assembly? Tolerance 6H indicates a standard metric internal thread tolerance that provides reliable mating with commonly used external thread classes for a precise fit. Which shank size is required for clamping? The tap features a shank Ø 7 mm, compatible with typical collets and chucks used in tapping heads and CNC machines. Does the design reduce tap breakage in long‑chip materials? The right‑hand 40° spiral and relief‑ground flanks are intended to control chip formation and reduce torque peaks, thereby lowering the risk of breakage in long‑chip materials. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from high wear resistance and consistent thread accuracy combined with confident handling in series production; order the TECWERK machine tap directly via Metav Werkzeuge or consult the specialists if guidance is required. Machine tap DIN 374C Univ. MF10x1.25mm, HSS‑Co – TECWERK A Machine tap DIN 374C Univ. MF10x1.25mm designed for producing metric fine internal threads in blind holes across steels and non‑ferrous materials. HSS‑Co construction for extended tool life 40° right‑hand spiral for improved chip control ISO fine thread MF with tolerance ISO2 (6H) Suitable for steel, stainless and non‑ferrous metals Consistent, production‑grade thread quality The combination of HSS‑Co substrate and ISO fine thread geometry ensures repeatable, high‑quality threads suitable for serial manufacturing. The tolerance class 6H (internal) aligns with DIN 13, providing interchangeability and reliable fit in assemblies. This means fewer rejects and less rework in the tapping operation, which directly supports higher throughput and predictable part quality. Efficient chip control for blind‑hole tapping A pronounced 40° spiral with right‑hand helix guides chips away from the cutting edge and reduces packing in blind holes, thereby lowering the risk of thread damage. The universal flute form delivers a balance between cutting efficiency and chip evacuation, giving steadier feed behaviour and a cleaner thread form. For shops machining blind threads, this geometry reduces interruptions and the need for frequent recutting. Versatile geometry for common workshop materials The universal Form C geometry and the tool’s relief grind on the flanks combine to handle a broad material range, including steel, stainless steel and non‑ferrous metals. The tap’s profile and cutting edge preparation make it a practical choice where mixed production runs demand a single, reliable tool rather than multiple specialised items, simplifying tool inventory and changeovers. Surface treatment and handling benefits The vapour‑coated surface improves resistance to adhesion and wear during interrupted cuts, while the green ring marking aids fast identification in tool cabinets. A Shaft Ø 7 mm supports secure clamping in standard toolholders and machine tap spindles. Together these features extend usable life and facilitate replacement planning, supporting a steady production rhythm with minimal downtime. Contact Metav Werkzeuge for tailored advice and rapid supply of TECWERK machine taps, including compatibility checks for specific machines and materials. Technical Data Article number: 2000867923NW Designation: Machine tap DIN 374C Univ. MF10x1.25mm HSS‑Co TECWERK Brand: TECWERK Packaging unit: 1 Data Thread: MF10 × 1.25 mm Tolerance: ISO2 (6H) Spiral angle: 40° Shaft Ø: 7 mm Special features HSS‑Co material Form C universal geometry Vapour‑coated surface Green ring identification Flank relief ground Complies with DIN 13 For blind holes Suitable for steel, stainless steel, nodular cast iron and non‑ferrous metals FAQ What thread does the tap produce and which standard applies? The tap produces a metric fine thread MF10 × 1.25 mm and is specified to DIN 13 with an internal tolerance field of 6H for consistent fit. Is the tool suitable for blind‑hole applications? Yes, the 40° right‑hand spiral and flute geometry are intended for blind holes, improving chip control and reducing the risk of chip jamming. Which materials can be machined with this tap? The tool is suitable for steel, stainless steel, nodular cast iron and various non‑ferrous metals, making it versatile for mixed production runs. How does the vapour coating affect performance? The vapour‑coated surface reduces adhesion and wear, which helps maintain cutting performance and extend tool life under typical workshop conditions. What is the SKU for ordering or referencing the tool? The SKU for the TECWERK machine tap is 2000867923NW, which can be quoted when enquiring or ordering. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a high-cobalt HSS-Co grade and a straight-flute design to achieve consistent, burr-free metric M10×1.5 threads in long-chip, soft materials. Benefit from the DIN‑371B conformity and ISO2 (6H) tolerance for interchangeable, precision screw threads — order via Metav Werkzeuge or consult the technical team for specific machining guidance. Machine Tap DIN 371B AL M10x1.5mm HSS‑Co 6H – Straight‑flute metric tap by TECWERK, shank Ø 10 mm The Machine Tap DIN 371B AL M10x1.5mm HSS‑Co 6H is a straight‑fluted cutting tool for producing ISO metric threads in through holes and similar applications, designed for long‑chip and softer materials. HSS‑Co for elevated hot hardness and wear resistance Straight flute for dependable chip evacuation Metric M10×1.5 thread to DIN 13, tolerance ISO2 (6H) Shank Ø 10 mm for secure machine clamping Consistent precision for interchangeable metric threads The combination of HSS‑Co material and the DIN conformity ensures both wear resistance and repeatable thread accuracy. The high‑cobalt steel provides improved hot hardness, which maintains cutting performance under elevated temperatures; this translates into longer tool life and steadier dimensional results. With the ISO2 (6H) tolerance and reference to DIN 13, the tool produces threads that meet established interchangeability standards. These technical qualities reduce scrap and rework in component production, supporting stable process economics and predictable assembly fits. Reliable chip control and smoother machining cycles Designed with a straight flute geometry and a peeling chamfer for through threads, the tap promotes controlled chip formation when machining long‑chip, soft materials. Straight flutes allow chips to exit axially, lowering the risk of chip clogging in blind or through holes and reducing torque spikes during threading. The relieved flanks reduce surface contact during threading, which improves cutting action and the finish of the thread flank. The net effect is fewer interruptions, shorter cycle times and a more reliable production flow when working with aluminium‑type and other ductile alloys. Machine compatibility and secure clamping for operational stability The tool adheres to the standardised DIN 371B form (Form B) and features a shank Ø 10 mm, enabling secure mounting in standard tap holders and automatic tapping spindles. This compatibility simplifies integration into existing setups, whether used on manual tapping heads or CNC tapping units. The standardised form factor supports rapid tool changes and consistent positioning, which helps maintain thread concentricity and surface quality across batches. Where repeatability and interchangeability matter, the standard dimensions and acceptance to DIN specifications are decisive advantages. Practical handling and application recommendations For best results, pair the tap with appropriate cutting fluid and machining parameters matched to the workpiece material; the HSS‑Co substrate tolerates elevated temperatures but benefits from lubrication to extend service life. The tool’s design — including the peeling chamfer for through threads — makes it especially suitable for continuous‑chip alloys; selecting chip breakers, coolant delivery and feed rates aligned to the workpiece will further reduce the risk of built‑up edge and improve thread quality. Regular inspection for wear and prompt replacement when flank wear affects tolerance will ensure ongoing thread conformity and minimise downstream quality issues. For dependable, high‑precision threading choose the TECWERK machine tap and contact Metav Werkzeuge for tailored technical advice or procurement assistance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 2000867230NW Product name: Maschinengewindebohrer DIN 371B AL M10x1,5mm HSS‑Co 6H TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Thread size: M10×1.5 Shank diameter: 10 mm Tolerance: ISO2 (6H) Standard: DIN 13 Blatt 1 Special features HSS‑Co material Form B (DIN 371B) Type AL, ringed shank design Straight‑fluted geometry Relieved flanks (flank grinding) Peeling chamfer for through threads Suitable for long‑chip, soft materials FAQ What materials is this tap best suited for? The TECWERK machine tap M10×1.5, made from HSS‑Co, is intended primarily for long‑chip, softer materials such as aluminium alloys and similar ductile metals where straight flutes promote reliable chip evacuation. What does the tolerance ISO2 (6H) mean for threaded parts? Tolerance ISO2 (6H) specifies the thread tolerance class according to ISO standards; the TECWERK tap produces threads within that class, ensuring interchangeability and conformity for standard metric fastenings. Can the tap be used in automatic tapping heads? Yes, the shank Ø 10 mm and Form B profile are compatible with standard tap holders and many automatic tapping devices, allowing stable clamping and consistent thread concentricity. How does the peeling chamfer affect threading performance? The peeling chamfer on this tool is designed for through threads and promotes easier chip separation and initiation of the cut, which helps reduce torque peaks and improves surface finish in through‑hole applications. Is any special coolant recommended for extending tool life? While HSS‑Co offers good heat resistance, the use of an appropriate cutting fluid or lubricant matched to the workpiece material will help reduce wear and maintain consistent thread quality for the TECWERK tap. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a high-cobalt construction and vapourised surface to achieve reliable M10 × 1.25 mm fine threads in demanding materials; the universal Form B geometry and straight flutes with flank relief reduce breakage and improve chip evacuation for uninterrupted production. Order the tool directly via Metav Werkzeuge or consult our technical advisers for application-specific recommendations. Machine tap DIN 374B – M10 × 1.25 mm, HSS-Co, vapourised (TECWERK) A machine tap for precision ISO fine threading (M10 × 1.25 mm) in steels, stainless steels, spheroidal cast iron and non‑ferrous metals. HSS-Co high-cobalt construction Vapourised wear‑resistant coating Straight flutes with flank relief ISO fine thread M10 × 1.25, tolerance 6H 7 mm shank for machine holders Consistent fine-thread performance for production work The machine tap DIN 374B is engineered to deliver repeatable M10 × 1.25 mm ISO fine threads with the tolerance class 6H specified by DIN 13. The combination of Form B geometry and a dedicated chamfer for through threads provides predictable engagement and reduced insertion torque, which translates into fewer rejects and less rework on threaded assemblies. This precision-focused design supports automated tapping cycles and maintains thread integrity across batch production. Durability and cutting reliability with high-cobalt steel Constructed from high-cobalt HSS (HSS‑Co) and finished with a vapourised coating, the tool offers elevated wear resistance when machining harder materials. The enhanced substrate hardness and surface treatment extend tool life and maintain cutting geometry under thermal stress, which is particularly beneficial when producing threads in stainless steels or spheroidal cast iron. The result is improved uptime and lower tool consumption compared with uncoated, conventional taps. Chip control and reduced risk of breakage The straight flutes paired with flank relief and a chip-breaking chamfer facilitate efficient chip flow during through-hole tapping. This geometry minimises chip build-up at the cutting edge and reduces axial loads, decreasing the likelihood of tap fracture in interrupted cuts or challenging spindles. For operations that demand smooth evacuation of chips and stable torque curves, the tool’s flute design supports reliable cycle times and consistent thread quality. Integration into workshop toolholding and workflows The tool features a 7 mm shank, compatible with common machine holders used in tapping heads and collet chucks. Its universal typology makes it adaptable across general-purpose tapping tasks while still offering the precision required for fine ISO threads. Documentation of the key specifications enables straightforward process planning and quality assurance measures on the shop floor, helping maintenance and purchasing coordinate stocking and replacement intervals. Select the TECWERK machine tap via Metav Werkzeuge for robust, production-ready fine-threading solutions; contact Metav Werkzeuge for tailored advice at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 2000867652NW Item designation: Machine tap DIN 374B M10 × 1.25 mm HSS‑Co vapourised Manufacturer: TECWERK Facts Thread: M10 × 1.25 mm Tolerance: ISO2 (6H) Shank diameter: 7 mm Packaging unit: 1 Special features HSS‑Co material Form B geometry Universal type Vapourised coating (green ring) Straight flutes, flank relief Chamfer for through threads (chip breaker) Suitable for steel, stainless steels, spheroidal cast iron, non‑ferrous metals Conforms to DIN 13 FAQ What materials can be machined with this machine tap? The TECWERK machine tap is suitable for steel, stainless steels, spheroidal cast iron and non‑ferrous metals, as specified in the tool’s technical features. What tolerance and thread standard does the tap produce? Threads are produced to ISO fine thread M10 × 1.25 mm with tolerance ISO2 (6H) in accordance with DIN 13. How does the vapourised coating benefit production use? The vapourised coating increases wear resistance and helps maintain cutting geometry at elevated temperatures, extending tool life during continuous production runs. Is the shank compatible with standard machine holders? Yes, the tool has a 7 mm shank, making it suitable for common collets and tapping holders used in automated and manual tapping setups. Can this tap be used for through-hole threading? Yes, the tap includes a chamfer designed as a chip-break feature specifically for through-hole threading applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of HSS‑Co performance and the precise MF10×1 metric fine thread combined with a 7 mm shank for reliable machine tapping and consistent thread quality. Order directly via Metav Werkzeuge or consult our specialists for process integration and batch optimisation. Maschinengewindebohrer DIN 374B MF10x1mm HSS‑Co 6H – Machine tap, TECWERK Maschinengewindebohrer DIN 374B MF10x1mm HSS‑Co 6H TECWERK is a machine tap designed for producing metric ISO fine threads (MF10×1) in a range of engineering materials, featuring straight flutes and a precision tolerance class for repeatable results in production environments HSS‑Co high‑performance cutting material DIN 374B form B, straight flutes MF10×1 metric fine thread, tolerance 6H 7 mm shank diameter for secure mounting Consistent high‑speed cutting with improved wear resistance The tool is manufactured from HSS‑Co, a cobalt‑alloy high‑speed steel that offers enhanced wear resistance and thermal stability compared with standard HSS. This material choice reduces tool change frequency under elevated cutting temperatures and supports reliable performance in serial production. For workshops and industrial users, the combination of durable cutting steel and a robust geometry translates to fewer interruptions and lower overall tool cost per thread produced. Precision geometry for repeatable thread quality Built to DIN 374B and providing the MF10×1 metric fine thread with a 6H tolerance, the tap guarantees threads that meet standardised fit requirements. The straight flutes and flank ground cutting edges are engineered to produce clean threads with consistent flank form, improving assembly behaviour and reducing rework. The included peeling cut for through threads helps to control chip formation and lowers torque during entry, which benefits both cycle time and finished surface integrity. Designed for machine use and a range of materials With a shank of 7 mm, the tap is ready for secure clamping in collets or toolholders commonly used on tapping heads and machining centres. It is suitable for use in steels up to 1000 N/mm², malleable cast iron and long‑chipping non‑ferrous metals, making it versatile for maintenance, toolroom tasks and small batch production. The form‑B design and straight flute profile support controlled chip evacuation when paired with appropriate direction and cutting fluid, enhancing efficiency in through‑hole tapping operations. For precise fine‑thread production and application advice, contact Metav Werkzeuge in Emmerich for the TECWERK MF10×1 machine tap and personalised process support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000867468NW SKU: 2000867468NW Designation: Maschinengewindebohrer DIN 374B MF10x1mm HSS‑Co 6H TECWERK Manufacturer: TECWERK Packaging unit: 1 UID: 2000867468NW Facts Thread: MF10×1 (metric ISO fine thread) Tolerance: 6H Shank diameter: 7 mm Suitable for steels up to approx. 1000 N/mm² Special features Material: HSS‑Co (cobalt‑alloy high‑speed steel) Form: B (DIN 374B) Flute type: straight flutes Flank treatment: flank ground Cutting edge: peeling cut for through threads Applications: malleable cast iron, long‑chipping non‑ferrous metals FAQ What materials can this machine tap process? The TECWERK machine tap is suitable for steels up to 1000 N/mm², malleable cast iron and long‑chipping non‑ferrous metals as stated in the product specification. What does the 6H tolerance mean for thread fit? A 6H tolerance is an ISO internal thread tolerance class that ensures a standardised medium fit for metric threads, providing reliable assembly behaviour for the MF10×1 thread. How does HSS‑Co affect tool life compared with standard HSS? HSS‑Co contains cobalt that increases hot hardness and wear resistance, typically extending tool life under higher cutting temperatures and reducing the frequency of tool changes. Why are straight flutes and flank grinding beneficial? Straight flutes aid controlled chip formation in through‑hole tapping, while flank ground edges reduce friction and improve surface finish, both contributing to consistent thread quality. Is the tap suitable for machine tapping setups? Yes, the 7 mm shank and machine‑grade geometry are intended for secure clamping in tapping heads and machine toolholders for automated tapping operations. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of HSS‑Co construction and Form C geometry for reliable fine‑thread production in blind holes; the ground flank relief and right‑hand 40° spiral improve chip evacuation and thread quality. Order the TECWERK machine tap directly via Metav Werkzeuge or consult our specialists for tailored advice. TECWERK Machine Tap DIN 374C M10×1 mm, HSS‑Co, Form C, 6H A TECWERK machine tap DIN 374C M10×1 mm engineered for producing metric ISO fine threads in blind holes across medium‑strength steels and long‑chipping non‑ferrous metals HSS‑Co for enhanced red hardness and wear resistance Form C geometry with ground flank relief Right‑hand spiral 40° for efficient chip evacuation Suitable for blind holes and steels up to ~1000 N/mm² Accurate fine threads with consistent tolerance The M10×1 mm metric fine thread, produced to DIN 13 and tolerance class 6H, ensures reproducible fit and assembly integrity where precise engagement is required. This machine tap delivers a predictable thread profile, reducing the need for downstream rework and enabling components to meet design tolerances reliably. The result is fewer rejects and consistently assembled parts for precision mechanical applications. Durable performance and improved chip control for blind holes Manufactured from HSS‑Co (cobalt high‑speed steel), the tool maintains cutting performance at elevated temperatures and resists accelerated wear in continuous production. The right‑hand spiral 40° combined with flank relief ground on the cutting flanks actively directs chips away from the cutting edge into the flutes, a key advantage when producing blind holes, as it reduces chip packing and minimises the risk of thread damage. The tap is rated for steels up to approximately 1000 N/mm², temper‑cast iron and long‑chipping non‑ferrous alloys, offering versatility across common workshop materials. Smooth machine integration and reliable handling The tool’s Form C design and a shaft diameter of 7 mm make the tap straightforward to clamp and align in standard tapping fixtures and holders, shortening setup time and improving process stability. Supplied as a single unit per packaging, the tap fits into a compact inventory strategy and supports lean tooling management. Combined with Metav’s quality filtering and wide product range, this tap contributes to an efficient workflow and dependable production results. For machines requiring precise fine threads in blind holes, contact Metav Werkzeuge for project guidance or to order the TECWERK machine tap and benefit from our technical expertise and reliable supply chain. Technical data Article number: 2000867483NW Manufacturer: TECWERK Packaging unit: 1 Facts Thread: M10×1 mm (metric fine) Standard: DIN 374C / DIN 13 Tolerance: 6H Shaft diameter: 7 mm Spiral angle: 40° Material strength rating: up to ≈1000 N/mm² Special features HSS‑Co Form C geometry Right‑hand spiral 40° Flank relief ground For blind holes Suitable for temper cast iron and long‑chipping non‑ferrous metals FAQ What materials can this machine tap process effectively? The TECWERK machine tap is suitable for steels up to approximately 1000 N/mm², temper cast iron and long‑chipping non‑ferrous metals, as specified for the tool. Is this tap suitable for blind‑hole threading only? This tool is designed specifically for blind holes, with a spiral geometry that helps evacuate chips away from the thread root during tapping. What does the tolerance class 6H mean for assemblies? Tolerance class 6H denotes a standard internal thread tolerance under DIN norms, providing a predictable clearance for mating external threads and consistent assembly performance. How does the HSS‑Co material benefit production? The HSS‑Co composition increases red hardness and wear resistance, maintaining cutting performance at higher temperatures and extending tool life under demanding conditions. What shaft size is required for clamping this tap in a holder? The tap has a shaft diameter of 7 mm, which is compatible with standard tapping fixtures and holders used in workshop and production environments. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a durable, machine-ready HSSE solution that delivers consistent ISO-class threads and straightforward integration with standard machine holders; order directly via Metav Werkzeuge or consult the technical team for application-specific guidance. VÖLKEL M12 HSSE machine tap bit — 1/4" hex shank, metric ISO thread, Form B VÖLKEL M12 HSSE machine tap bit designed for efficient production of metric ISO threads in unalloyed and low-alloy steels, optimised for machine holders with a 6.3 mm (1/4") hex shank HSSE (HSS with cobalt) for higher wear resistance Metric ISO thread, tolerance ISO2 (6H) 6.3 mm (1/4") hex shank for machine holders Form B, DIN 376 standard, length 110 mm Precision threads with industrial repeatability The supplied machine tap bit is engineered to produce M12 metric ISO threads to ISO2 (6H) tolerance, ensuring consistent fit and interchangeability across mating components. Made from HSSE (high-speed steel with cobalt), the tool maintains cutting-edge hardness at elevated temperatures, which translates into prolonged tool life under continuous machine cycles. The Form B geometry and DIN 376 compliance simplify process planning: the standardised profile reduces variation between batches, enabling predictable assembly behaviour and fewer rejected parts. Material capability and performance advantages The tap bit is specified for general use in readily machinable materials up to 900 N/mm², including unalloyed and low-alloy steels. The HSSE substrate offers improved red hardness and resistance to abrasive wear compared with conventional HSS, which benefits high-throughput environments and light interrupted cuts. The included chamfer for through threads (Schälanschnitt) improves chip evacuation in through-hole tapping, lowering the risk of chip jams and reducing cycle interruptions—an efficiency gain that impacts overall productivity. Simple machine integration and secure clamping A 6.3 mm (1/4") hex shank allows direct insertion into common machine tool holders and quick-change adapters, eliminating time-consuming re-clamping while enhancing torsional stability during tapping. At a length of 110 mm, the tool balances reach and rigidity for typical bench and production centre setups. Compatibility with standard holders reduces fixture costs and supports rapid changeovers, which is particularly useful in mixed-production facilities where minimising downtime is crucial. Practical guidance for application and process reliability Form B execution and the tool’s geometry are optimised for through-thread operations; when pairing this tap bit with appropriate lubricants and correct spindle speeds, chip control improves markedly. For tapered or blind-thread operations, adjustments to cycle parameters and coolant strategy are recommended. Metav's technical literature gives process windows for spindle speed and feed adapted to HSSE taps in steels up to 900 N/mm², and Metav's technical team can advise on optimised parameters for specific setups. Contact Metav Werkzeuge for tailored application advice or to request a specification sheet and order details for the VÖLKEL M12 HSSE machine tap bit Technical data Article number: 4000868078NW SKU: 4000868078NW Brand: VÖLKEL Facts Thread: M12 metric ISO thread Pitch: 1.75 mm Length: 110 mm Shank: 6.3 mm (1/4") hex Tolerance: ISO2 (6H) Special features Material: HSSE (high-speed steel with cobalt) Form: Form B Standard: DIN 376 (WN) Chamfer: chamfer for through threads Application: general machining in unalloyed and low-alloy steels up to 900 N/mm² FAQ What materials is this tap bit suitable for? The VÖLKEL M12 HSSE machine tap bit is intended for unalloyed and low-alloy steels and comparable materials up to 900 N/mm², providing reliable performance in commonly machined steels. Which shank type does the tool use and why is that important? The tap bit features a 6.3 mm (1/4") hex shank, allowing secure clamping in common machine holders and quick-change adapters for improved torsional stability and faster changeovers. What does ISO2 (6H) tolerance mean for assembly? ISO2 (6H) indicates a standard tolerance class for internal threads; using the VÖLKEL M12 HSSE tap bit achieves predictable thread fit and interchangeability with ISO-compliant mating parts. Is the tool suitable for blind-hole tapping? The geometry and chamfer are optimised for through-thread tapping; for blind-hole applications, process parameters and coolant strategy should be adapted—Metav's technical team can advise on suitable adjustments. What standard does the tap conform to and why is this relevant? The tool conforms to DIN 376 (WN), Form B, ensuring standardised geometry and processability, which supports consistent production quality and simplifies quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the HSSE cutting material, the Form C (15° RSP) geometry and the quick-change 6.3 mm (1/4") hex shank for reliable blind-hole threading; the tool is designed for machinable steels up to 900 N/mm². Order the machine thread tap bit directly via Metav Werkzeuge or ask our consultants if needed. Machine thread tap bit HSSE 9 M12×10.20 mm, pitch 1.75 mm — VÖLKEL, 6.3 mm hex shank A VÖLKEL machine tap bit designed for forming metric ISO threads in blind holes, optimised for general workshop and CNC applications in unalloyed and low-alloy steels. HSSE cobalt for enhanced wear resistance Form C 15° RSP geometry 6.3 mm (1/4") hex shank for machine use Suitable for blind hole threads up to 900 N/mm² Consistent blind-hole threading with minimal rework The HSSE composition ensures wear resistance and temperature stability during interrupted cuts, which translates into fewer tool changes and more productive machine hours. Combined with the Form C (15° RSP) flute geometry, the tool evacuates chips reliably from blind holes, reducing the risk of chip packing and rework. This results in more consistent thread quality and repeatable threads in production batches, particularly when processing unalloyed or low-alloy steels up to 900 N/mm². Accurate fit and compatibility with standard toolholders Designed for metric ISO threads with ISO2 (6H) tolerance, the bit supports precise assembly fit tolerated by most engineering applications. The 6.3 mm (1/4") hex shank provides secure engagement in chucks and quick-change adapters, reducing setup time on both manual drilling rigs and CNC tapping heads. Compliance with WN (DIN 376) and the defined thread geometry helps maintain interchangeability across fixtures and mating parts, simplifying quality assurance and inventory planning. Durable geometry that supports workshop efficiency The tool length of 110 mm and compact profile make it suitable for restricted access and deep blind-hole tapping where clearance is limited. The HSSE material and the selected flute form extend tool life under typical shop conditions, lowering per-thread costs and downtime. For production environments seeking to optimise throughput, the bit’s balance of durability and chip control supports steady, high-quality output with reduced scrap rates. For precise metric blind-hole threading, request this VÖLKEL HSSE machine tap bit (SKU 4000868085NW) from Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com for application guidance Technical Data Article number: 4000868085NW Brand: VÖLKEL GmbH Length: 110 mm Thread: M12 × 10.20 mm, pitch 1.75 mm Shank: 6.3 mm (1/4") hex shank Facts Tolerance field: ISO2 (6H) Material suitability: up to 900 N/mm² Standard: WN (DIN 376) Cutting material: HSSE Special features Form C (15° RSP) geometry Metric ISO thread for blind holes HexDrive quick-change interface Intended for unalloyed and low-alloy steels FAQ What materials can this tap bit handle? The VÖLKEL machine tap bit is specified for general use in machinable materials up to 900 N/mm², notably unalloyed and low-alloy steels. Is the thread tolerance suitable for assembly with standard nuts and bolts? Yes, the tool produces metric ISO threads to the ISO2 (6H) tolerance class, compatible with common fastening and assembly standards. Which standard and form does the tool conform to? The tap bit follows WN (DIN 376) with Form C (15° RSP) flute geometry and is made from HSSE cutting material. What toolholders are compatible with the shank? The 6.3 mm (1/4") hex shank fits standard quick-change holders and hex collets commonly used in workshop and CNC tapping operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of high‑performance HSS‑Co cutting geometry, a vapourised wear‑resistant finish and a through‑hole chamfer for reliable, fast machining of metric fine threads. Order the tap directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Machine tap DIN 374B Universal MF12×1 mm HSS‑Co vapourised (6H) — TECWERK The Machine tap DIN 374B Universal MF12×1 mm HSS‑Co vapourised (6H) is a straight‑flute machine tap designed for producing precise metric fine internal threads in a wide range of engineering materials. HSS‑Co for increased wear resistance Straight flutes with back‑tapered flanks Vapourised coating for extended tool life ISO fine thread MF12×1 mm, tolerance 6H Consistent fine‑thread accuracy for demanding assemblies The tap is manufactured to DIN 374B with a metric fine thread (MF12×1 mm) and ISO2 tolerance (6H), ensuring repeatable thread quality where fit and sealing are critical. The use of HSS‑Co (cobalt high‑speed steel) raises hot‑hardness and wear resistance compared with conventional high‑speed grades, which keeps dimensional stability longer under production loads. Specified to DIN standards, the tool provides an objective basis for process planning and quality assurance in industrial environments. Improved chip control and reduced rework on through holes Equipped with straight flutes and back‑tapered flanks, the tool promotes predictable chip formation and safe evacuation in through‑hole operations. The integrated through‑hole chamfer (Schälanschnitt) shortens the lead‑in and reduces thread burrs, lowering the need for secondary finishing. These geometric features translate into shorter cycle times and fewer rejects, which is particularly relevant where production efficiency and assembly reliability are priorities. Durable finish and easy identification for busy toolrooms A vapourised coating with the characteristic green ring provides enhanced surface hardness and corrosion resistance without obscuring cutting edges, supporting longer life in mixed‑material machining. The shank Ø 9 mm enables secure clamping in standard holders and quick tool changes, helping workshop operatives maintain steady throughput. The universal form B designation makes the tap a versatile choice across maintenance, fabrication and production settings where a balanced combination of performance and economy is required. Suitable applications and integration into supply chains Designed for use with steel, stainless steel, spheroidal graphite cast iron and non‑ferrous metals, this tap fits repair shops, toolrooms and industrial production lines where metric fine threads are specified. Compliance with recognised standards simplifies procurement and inspection processes. As a reliable partner for precision tools, Metav Werkzeuge supports supply continuity and offers technical advice to align tool selection with machining parameters and materials. For accurate fine‑thread production with a robust HSS‑Co geometry, contact Metav Werkzeuge for ordering or tailored machining guidance — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 — Metav’s specialists will advise on integrating the TECWERK machine tap into existing workflows Technical data Article number: 2000867653NW Product: Machine tap DIN 374B Universal MF12×1 mm HSS‑Co vapourised (6H) Manufacturer: TECWERK Packaging unit: 1 Core data Material: HSS‑Co Form: B (Universal) Thread: MF12×1 mm, DIN 13, tolerance ISO2 (6H) Shank diameter: 9 mm Coating: vapourised (green ring) Flute type: straight flutes Special feature: through‑hole chamfer Special features Flanks back‑tapered (relieved) Colour identification: green ring Designed for steel, stainless steel, spheroidal graphite cast iron and non‑ferrous metals Suitable for through‑hole threading applications FAQ Is this tap suitable for stainless steel? The TECWERK machine tap is specified for stainless steels and is manufactured in HSS‑Co to improve wear resistance during stainless steel threading. What thread tolerance and standard does the tool achieve? The tool produces a metric fine thread MF12×1 mm to DIN 13 with an ISO2 (6H) tolerance field for consistent assembly fits. Does the tap have a coating and how is it identified? Yes, the tap features a vapourised coating and is identified by a green ring to denote the surface finish. Can the tap be used for blind holes? The geometry includes a through‑hole chamfer optimised for through threads; blind‑hole applications require process adjustment and are not the primary intent of this chamfer design. What shank size is required for clamping? The tap has a shank diameter of 9 mm for secure mounting in compatible holders. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund