P2841S-1N-E67 WKP35S Wendeplatten - Walter Tools
Take advantage of Tiger·tec Silver performance together with the WKP35S coated carbide grade for sustained tool life and consistent chip control; order directly via Metav Werkzeuge or consult our specialists for application advice. Bohr-/Aufbohrwendeschneidplatte P2841S-1N-E67 WKP35S – Tiger·tec Silver, for Steel and Cast Iron (Walter Tools) A P2841S-1N-E67 WKP35S indexable insert engineered for drilling and bore‑enlarging tasks, delivering reliable wear resistance and optimised chip formation in steel and cast iron applications. Tiger·tec Silver coated carbide Optimised for steel and cast iron machining Stable chip control with 1N‑E67 breaker High wear resistance and predictable tool life for productive machining The combination of the Tiger·tec Silver coating and the WKP35S carbide grade provides a robust cutting edge designed to withstand the thermal and abrasive demands of machining steel and cast iron. This engineered coating system reduces crater wear and improves resistance to thermal shocks, resulting in longer tool life and fewer tool changes. For production environments where cycle time and tool-change frequency directly affect throughput, the coated substrate yields a measurable improvement in process stability and cost efficiency. The technical design supports elevated cutting speeds while maintaining dimensional consistency, which benefits both single‑piece flow and batch production. Consistent chip control for quieter, safer cycles and better surface finish The integrated 1N‑E67 chipbreaker geometry focuses on controlled chip formation to prevent long or entangling swarf during drilling and bore‑enlarging operations. Stable chips reduce the risk of workpiece damage and tool interference, leading to fewer stoppages and more predictable cycle times. When machining in the ISO P and K groups, the insert’s geometry helps produce short, breakable chips in both unalloyed and alloyed steels and in abrasive cast iron grades. The outcome is improved surface integrity and a reduced need for secondary finishing, supporting higher first‑pass quality and lower overall process costs. Application fit and process reliability for workshop and production use Intended for drilling and bore‑enlarging applications, the insert aligns with common Walter Tools systems and clamping interfaces, enabling straightforward integration into existing tool holders. Its suitability for the P / K material groups makes it a versatile choice for mixed‑material shops that require a single, reliable insert for varied tasks. The coating and chipbreaker combination promotes process reliability, especially in longer runs where tool performance consistency is essential. Selection of this insert supports predictable maintenance intervals and helps to safeguard up‑time in both jobbing shops and serial production. Contact Metav Werkzeuge for tailored application advice and to confirm the best Tiger·tec Silver WKP35S insert configuration for specific drilling requirements Technical Data SKU: P2841S-1N-E67-WKP35S-WALTER Product: Bohr-/Aufbohrwendeschneidplatte Designation: P2841S-1N-E67 WKP35S Series: Tiger·tec Silver Grade: WKP35S Chipbreaker: 1N‑E67 Manufacturer: Walter Tools Facts Material groups: P (steel), K (cast iron) Suitable for: Steel, Cast iron Special features Coated carbide grade (Tiger·tec Silver) For drilling and bore‑enlarging applications Optimised chip control with 1N‑E67 Designed for stable wear behaviour FAQ What materials is this insert suitable for? The P2841S‑1N‑E67 WKP35S insert is designed for machining steel and cast iron, corresponding to the ISO P and K material groups. What is the benefit of the 1N‑E67 chipbreaker? The 1N‑E67 chipbreaker promotes short, controllable chips during drilling and bore‑enlarging, improving cycle stability and surface finish with reduced swarf issues. How does the Tiger·tec Silver coating affect performance? The Tiger·tec Silver coating enhances wear resistance and thermal stability, which supports higher cutting speeds and extends the effective life of the insert in demanding operations. Is this insert compatible with common Walter toolholder systems? The insert designation P2841S‑1N‑E67 WKP35S aligns with standard drilling and enlarging insert geometries used in Walter tooling systems; confirm holder compatibility when specifying. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarked names and product descriptions are used solely for identification and explanation. Brand names and protected trademarks remain the property of their respective owners. No affiliation between Metav Werkzeuge and the referenced brands is implied. The offered item is an original, factory‑new product from the manufacturer.
P2841S-1N-E67 WSP45G Wendeplatten - Walter Tools
Benefit from the Tiger·tec Gold coating and the versatile WSP45G grade for reliable chip control, extended tool life and consistent machining results; order the insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. P2841S-1N-E67 WSP45G Drill/Bore Indexable Insert — Tiger·tec Gold grade | Walter Tools The P2841S-1N-E67 WSP45G is a Tiger·tec Gold coated indexable insert engineered for drilling and bore-enlargement operations across demanding materials. Tiger·tec Gold PVD coated grade WSP45G Suitable for Stahl, rostfreier Stahl and superalloys Stable cutting edge with versatile chip control Extended service life through advanced coating The Tiger·tec Gold series combines a robust PVD coating with a wear-resistant substrate to reduce flank and crater wear under typical drilling loads. The WSP45G grade is a coated carbide developed for toughness and surface protection; this results in longer intervals between index changes and fewer unplanned machine stops. In practical terms, operators benefit from predictable tool life and reduced tool inventory turnover, which supports smoother production planning without sacrificing cutting performance. Confident machining of mixed material batches Designed for the ISO groups P / M / S, the insert handles unalloyed and alloyed Stahl, rostfreier Stahl and heat-resistant superalloys including Titan. Each material class places different thermal and mechanical stresses on the cutting edge: steels demand good heat dissipation, rostfreier Stahl needs stable chip formation to avoid built-up edge, and superalloys require thermal resistance and edge integrity. The WSP45G composition balances these demands, enabling one grade to cover a broad workshop range and reducing tool changes when batches contain mixed materials. Consistent chip control for efficient cycle times The integrated 1N-E67 chipbreaker geometry delivers controlled chip fragmentation and evacuation during drilling and bore-enlargement. Stable chip control reduces recutting, improves hole quality and lowers the risk of tool breakage in long-cycle operations. Combined with a robust cutting edge, the chipbreaker supports higher material removal rates while maintaining surface finish, so process windows can be tightened for improved throughput without compromising component tolerance. Predictable process security and productive machining As part of the Tiger·tec Gold family by Walter Tools, this insert emphasises a balance between toughness and wear resistance to maintain a consistent edge over extended runs. That predictability translates into fewer interruptions, stable surface quality and better overall productivity on CNC platforms. For shops seeking reproducible results in series production or for specialist components made from anspruchsvolle Werkstoffe, the insert provides a reliable cutting solution that aligns with modern productivity goals. If machining recommendations are required, Metav Werkzeuge consultants can advise on speeds, feeds and holder compatibility. Contact Metav Werkzeuge for tailored machining recommendations on this Walter Tools Tiger·tec Gold insert and to discuss suitable toolholders or batch strategies. Technical Data Article number: P2841S-1N-E67-WSP45G-WALTER Designation: P2841S-1N-E67 WSP45G Series: Tiger-tec Gold Grade: WSP45G Chipbreaker: 1N-E67 Material classification: P / M / S Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools UID: P2841S-1N-E67-WSP45G-WALTER Facts Applicable material groups: P / M / S Special features Coating: Tiger·tec Gold (PVD-coated) Material: coated carbide Suitable for: Stahl Suitable for: rostfreier Stahl Suitable for: superalloys and Titan FAQ What materials can be machined with this insert? The P2841S-1N-E67 WSP45G insert is designed for the ISO groups P / M / S, meaning it is suitable for machining Stahl, rostfreier Stahl and heat‑resistant superalloys including Titan. How does the Tiger·tec Gold coating benefit production runs? The Tiger·tec Gold coating on the WSP45G grade improves wear resistance and edge stability, resulting in longer tool life and more predictable intervals between indexing in continuous production. Which chipbreaker is integrated and what is its benefit? The insert features the 1N-E67 chipbreaker, which promotes reliable chip control and evacuation during drilling and bore-enlargement, enhancing hole quality and reducing the risk of recuts. Is this insert compatible with high-speed drilling operations? The WSP45G grade is engineered for good thermal and mechanical resistance; process parameters should be selected according to material and machine capabilities to exploit high-speed potential while ensuring edge stability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names belong to their respective owners. Brand names and registered trademarks are used for descriptive purposes only and indicate no affiliation or endorsement. The offered item is an original, factory‑new product of the manufacturer.
P2841S-1N-E67 WXP40 Wendeplatten - Walter Tools
Benefit from a combination of cost-effective, uncoated carbide performance and controlled chip formation for consistent drilling and boring operations; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. Bohr-/Aufbohrwendeschneidplatte P2841S-1N-E67 WXP40 by Walter Tools — uncoated carbide, chipbreaker 1N‑E67 The P2841S-1N-E67 WXP40 is a drill/reaming indexable insert intended for drilling and boring applications, offering an uncoated carbide grade and a dedicated 1N‑E67 chipbreaker for improved chip control and stable cutting conditions. Uncoated carbide grade WXP40 1N‑E67 chipbreaker for reliable chips Designed for drilling and boring operations Walter Tools quality and process reliability Increased productivity through stable cutting performance The combination of uncoated carbide and the WXP40 grade provides a predictable cutting behaviour that supports productive machining. The insert’s substrate, described as an uncoated cemented carbide, aims to deliver stable chip formation and consistent cutting edge geometry under standard drilling and boring conditions. For manufacturing environments where cycle time and repeatability matter, this indexable solution can help reduce rework and interruptions, because consistent chip control reduces the risk of tool dwell and re-cutting. Selection based on the tool matrix is recommended to align the insert variant with specific workpiece materials, ensuring optimal throughput. Better chip control and reduced process variability The integrated 1N‑E67 chipbreaker is engineered to shape and break chips during holemaking, which contributes to process security and safer chip evacuation. Controlled chip form lowers the likelihood of chip entanglement and improves coolant access to the cutting zone, supporting longer tool life and fewer interruptions on automated lines. The pragmatic design focus is on reliable performance in drilling and boring operations, where predictable chip flow and repeatable hole quality are decisive. The P2841S-1N-E67 WXP40 insert is therefore a practical choice when chip management and stable machining are priorities. Practical guidance for application and compatibility Material suitability for this insert is catalog-dependent, so compatibility must be verified against the manufacturer’s product matrix. The open series designation indicates a versatile cutting grade intended for a range of applications; nonetheless, confirmation of the correct variant is essential when machining alloys, hardened steels or exotic materials. Walter Tools’ engineering background supports consistent manufacture quality and tool performance; combine this technical information with cutting parameters from the tool matrix to achieve the intended surface finish and hole tolerance. When in doubt, consult the technical data sheets or request application guidance before series-wide deployment. For demanding drilling and boring tasks, rely on Walter Tools’ WXP40 performance—contact Metav Werkzeuge for tailored application advice and prompt supply. Technical data SKU: P2841S-1N-E67-WXP40-WALTER Article: Bohr-/Aufbohrwendeschneidplatte P2841S-1N-E67 WXP40 Manufacturer: Walter Tools Facts Series: Walter Schneidstoffsorte - Serie offen Grade: WXP40 (uncoated cemented carbide) Chipbreaker: 1N‑E67 Special features Application: drilling and boring Material specification: catalog-dependent Design: indexable insert for holemaking tasks FAQ What materials is this insert suitable for? The P2841S-1N-E67 WXP40 is an uncoated carbide insert; material suitability must be checked in the Walter Tools product matrix to confirm compatibility with specific workpiece materials. How does the 1N‑E67 chipbreaker improve performance? The 1N‑E67 chipbreaker shapes chips during drilling and boring, improving evacuation and reducing process variability, which supports more stable machining and longer tool life. Is this insert coated or uncoated? This indexable insert uses an uncoated cemented carbide grade (WXP40), designed for predictable cutting behaviour in a variety of holemaking applications. Can this insert be used for both drilling and boring operations? Yes, the geometry and design intent of the insert suit both drilling and boring tasks, with the chipbreaker and substrate tailored to holemaking performance. The Walter AG (brand Walter Tools) with headquarters in Tübingen belongs to the worldwide leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanation only. There is no connection between our company and the named brands. The offered item is original, factory-new merchandise of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
P2841S-1N-F57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating and the WKP35S grade for extended tool life and reliable chip control; the optimised 1N‑F57 chipformer ensures consistent performance in steel and cast iron operations. Order the P2841S-1N-F57 WKP35S directly via Metav Werkzeuge or consult our experts for application guidance. P2841S-1N-F57 P2841S-1N-F57 WKP35S – Drilling/Boring Indexable Insert for steel & cast iron by Walter Tools The P2841S-1N-F57 WKP35S is an indexable insert engineered for drilling and boring tasks in steel and cast iron, combining a coated carbide grade with a dedicated chipformer for controlled chip formation. Tiger·tec Silver coating for long tool life Optimised 1N‑F57 chipformer for stable chips Suitable for steel and cast iron machining Walter Tools quality and consistent results Extended lifetime through advanced coating technology The core advantage lies in the Tiger‑tec Silver coating applied to the WKP35S grade, a multilayer CVD/PVD‑style treatment developed for demanding metalcutting. This coating reduces flank and crater wear under the typical thermal loads of steel machining and minimises abrasive wear when turning cast iron, which leads to fewer tool changes and higher machine uptime. For production environments this means a measurable improvement in process security and a lower cost per component, achieved by maintaining cutting edge integrity for longer intervals. Stable chip control for safer, more efficient machining The integrated 1N‑F57 chipformer geometry is engineered to break and evacuate chips reliably in through‑tool and conventional drilling applications. A dedicated chipformer shapes the swarf into short, controllable segments, reducing the risk of entanglement and improving coolant access to the cutting zone. As a result, operators benefit from more predictable cycle times and improved surface quality, while tool life becomes easier to forecast — a practical advantage for batch production and automated cells. Optimised for ISO P and K material groups This insert is tailored to the ISO material classes P (unalloyed and alloyed steel) and K (cast iron), reflecting the substrate and coating choices that balance toughness and abrasive resistance. For users less familiar with these designations: ISO P implies suitability for the heat and ductility encountered when machining steels, whereas ISO K indicates resistance to the abrasive, often short‑breaking chips typical of cast irons. Selecting a grade designed for both groups reduces the need for multiple insert types across mixed‑material production. Consistent performance and economical operation in industrial use Manufactured to Walter Tools standards, the insert delivers repeatable edge geometry and dimensional reliability, supporting stable tolerance control across runs. By combining a robust grade with a specific chipformer and proven coating, the component offers a pragmatic balance between productivity and predictable maintenance intervals. For production planners this translates into simpler tooling strategies and less downtime for regrinding or replacement, supporting continuous, high‑quality output in demanding machining environments. For application recommendations with Walter Tools' Tiger‑tec Silver inserts such as the P2841S-1N-F57 WKP35S, contact Metav Werkzeuge for tailored suggestions and fast delivery Technical Data Article number: P2841S-1N-F57-WKP35S-WALTER Designation: P2841S-1N-F57 WKP35S Product type: Drilling/Boring indexable insert Manufacturer: Walter Tools Facts Material groups: P / K Series: Tiger·tec Silver Chipformer: 1N‑F57 UID: P2841S-1N-F57-WKP35S-WALTER Special features Coating: Tiger‑tec Silver Grade: WKP35S Suitable for: steel, cast iron Geometry: P2841S-1N-F57 FAQ What materials is this insert suitable for? The insert is designed for steel (ISO P) and cast iron (ISO K) applications; the WKP35S grade and Tiger‑tec Silver coating provide the wear resistance and toughness required for these groups. What benefit does the Tiger‑tec Silver coating provide? Tiger‑tec Silver enhances flank and crater wear resistance on the insert, extending service life and improving process stability during continuous drilling and boring operations. How does the 1N‑F57 chipformer improve machining? The 1N‑F57 chipformer shapes chips into short segments for secure evacuation, reducing entanglement and helping to maintain consistent surface finish and cycle times. Is this insert suitable for both drilling and boring operations? Yes, the geometry and grade are intended for drilling/boring indexable insert applications, offering reliable cutting behaviour in both operation types. Which designation identifies the exact insert geometry? The geometry and series are shown in the designation P2841S-1N-F57 WKP35S, which indicates the insert form, chipformer and the Walter grade. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The item offered is an original, factory‑new product of the manufacturer.
P2841S-1N-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold PVD coating and the versatile WSP45G grade for stable cutting-edge performance and reliable chip control in drilling and boring operations. Order the insert directly via Metav Werkzeuge or ask the consultants for cutting-data recommendations. P2841S-1N-F57 WSP45G indexable insert for drilling and boring – Tiger·tec Gold by Walter Tools The P2841S-1N-F57 WSP45G is an indexable insert engineered for drilling and bore-enlargement work, delivering versatile cutting performance across difficult materials such as Stahl, rostfreier Stahl and heat-resistant alloys. Tiger·tec Gold PVD-coated carbide Suitable for Stahl, rostfreier Stahl, superalloys Stable cutting edge and reliable chip control Optimised for drilling and boring operations High thermal and mechanical stability for consistent tool life The insert’s placement in the Tiger·tec Gold series and its WSP45G composition mean a PVD-coated carbide substrate designed to resist thermal loads and abrasive wear. This combination supports a stable cutting edge under the high temperatures typical of drilling and boring industrial cycles. The grade’s balanced toughness and wear resistance reduce unplanned tool changes and help maintain process reliability in serial production, which contributes directly to improved overall productivity. Effective chip control that reduces rework and downtime Equipped with the 1N-F57 chipbreaker geometry, the cutting face promotes controlled chip formation and evacuation during hole-making. Improved chip control minimises the risk of chip entanglement and tool damage, particularly in deeper holes or interrupted cuts. The measurable benefit is fewer stoppages for cleaning and a steadier surface quality on workpieces, achieving more predictable cycle times and lower scrap rates. Geometry and application focus for drilling and boring efficiency The insert geometry is optimised for axial engagement and stable contact in drilling and bore-enlargement setups. Its design supports secure seating in compatible tool holders and consistent engagement in the bore wall, which helps to avoid chatter and ensures repeatable hole tolerances. For operations requiring a balance of feed and speed, the combination of geometry and the WSP45G grade helps protect the cutting edge while delivering reliable hole finishes. Material compatibility and practical guidance for shop-floor use Rated for the ISO 513 groups P, M and S, the insert is suitable for machining Stahl, rostfreier Stahl and heat-resistant superalloys and titanium-type materials. These classifications indicate the intended workpiece groups and guide the selection of cutting speeds and feeds; for unfamiliar applications, empirical validation with conservative parameters is recommended. The series’ emphasis on robust edge behaviour and consistent chip formation makes the insert a practical choice for mixed-production environments where material changeovers are frequent. Choose the Walter Tools Tiger·tec Gold grade for demanding hole-making tasks and contact Metav Werkzeuge for tailored cutting-data and application support at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: P2841S-1N-F57-WSP45G-WALTER Designation: P2841S-1N-F57 WSP45G Product type: Indexable insert for drilling and boring Manufacturer: Walter Tools Grade: WSP45G Core specifications Material groups (ISO 513): P, M, S Chipbreaker: 1N-F57 Material of grade: PVD-coated carbide Series: Tiger·tec Gold Special features Suitable for Stahl Suitable for rostfreier Stahl Suitable for superalloys and titanium-type materials Robust cutting edge and stable chip formation FAQ What materials is this insert suitable for? The P2841S-1N-F57 WSP45G insert is suitable for Stahl, rostfreier Stahl and heat-resistant superalloys (ISO 513 groups P, M and S). What is the benefit of the Tiger·tec Gold coating? The Tiger·tec Gold PVD coating on the WSP45G grade improves thermal resistance and wear behaviour, extending the insert’s useful life in demanding hole-making operations. How does the 1N-F57 chipbreaker affect machining? The 1N-F57 chipbreaker promotes predictable chip formation and evacuation, reducing the likelihood of chip-related interruptions and enhancing surface consistency in drilling and boring. Can this insert be used for titanium and nickel-based alloys? Yes; the S group designation indicates suitability for heat-resistant superalloys and titanium-type materials, where edge stability and heat resistance are critical. Is the insert compatible with standard drilling tool holders? The insert is designed for indexable drilling and boring systems; tool-holder compatibility should be confirmed against the insert designation P2841S-1N-F57 WSP45G and the holder’s specifications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original factory-new goods of the manufacturer.
P2841S-1N-F57 WXP40 Wendeplatten - Walter Tools
Combining the WXP40 uncoated carbide grade with the 1N‑F57 chipbreaker results in reliable chip formation and stable holemaking, reducing unplanned interruptions and improving process throughput; order the insert directly via Metav Werkzeuge or ask the consultants for application advice. P2841S-1N-F57 WXP40 — Indexable Drilling/Reaming Insert, Uncoated Carbide, 1N‑F57 Chipbreaker (Walter Tools) The P2841S-1N-F57 WXP40 is an indexable drilling and reaming insert designed for consistent chip control and robust performance in general-purpose holemaking applications Uncoated carbide grade WXP40 1N‑F57 chipbreaker for consistent chips Designed for drilling and hole enlargement Walter Tools original indexable insert Predictable chip control for uninterrupted production The combination of the 1N‑F57 chipbreaker and the insert geometry delivers predictable chip control, which reduces the risk of swarf accumulation in deep holes and limits cycle interruptions. Stable chip formation translates into fewer manual interventions and consistent surface quality, helping to maintain productive machine cycles and predictable process times. As an indexable insert, the part is intended for quick replacement in multi‑insert drills and boring heads, which shortens downtime and supports lean shopfloor routines. Material grade and selection guidance for reliable performance Manufactured in the WXP40 uncoated carbide grade, the insert offers a straightforward cutting solution where an uncoated hardmetal is appropriate; the exact substrate composition is catalogue dependent and should be verified in the product matrix. The advantage of an uncoated grade is often simpler edge preparation and predictable tool behaviour across a broad range of conditions. For workpiece compatibility and optimum cutting data, consult the product matrix or Metav Werkzeuge to match the insert grade to the specific material and machining strategy. Integration into drilling systems and holder compatibility The insert is made for use in drilling and hole‑enlargement assemblies and is compatible with indexable drill and boring toolholders that accept the P2841S geometry. Correct clamping and tool holder condition are decisive for achieving the advertised performance; therefore, tool set‑up and runout control are practical preconditions for process reliability. When mounted correctly, the geometry supports steady feed rates and consistent hole size, aiding repeatability across batches in a production environment. Process benefits, productivity and brand reassurance Choosing an insert from Walter Tools provides access to a vendor with a recognised track record in precision cutting tools, supporting process reliability and consistent outcomes in industrial machining environments. The P2841S‑style insert, combined with the WXP40 grade and 1N‑F57 chipbreaker, offers a pragmatic balance between tool life and predictable behaviour, which can contribute to improved throughput and lower total machining cost per hole when integrated into a controlled machining process. For tailored advice on integrating Walter Tools P2841S‑1N‑F57 WXP40 inserts into existing tool holders and production routines, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for application support and delivery options Technical Data SKU: P2841S-1N-F57-WXP40-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P2841S-1N-F57 WXP40 Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte (indexable drilling/reaming insert) Manufacturer: Walter Tools Internal designation: P2841S-1N-F57 ISO designation: P2841S-1N-F57 WXP40 Grade: WXP40 Chipbreaker: 1N‑F57 Series: Walter Schneidstoffsorte - Serie offen Material info: Katalogabhängig UID: P2841S-1N-F57-WXP40-WALTER Facts Chipbreaker code: 1N‑F57 Grade code: WXP40 Series designation: Walter Schneidstoffsorte - Serie offen Special features Uncoated carbide insert (verify substrate in catalogue) Designed for drilling and hole enlargement applications Indexable insert geometry for fast replacement Suitability: check the product matrix for workpiece materials FAQ What materials is this insert suitable for? Suitability must be checked against the product matrix; the P2841S‑1N‑F57 WXP40 is an uncoated carbide grade and its application range depends on the specific substrate listed in the catalogue and the machining strategy. Is the insert coated? The WXP40 designation denotes an uncoated carbide grade for the P2841S‑1N‑F57 insert, so no surface coating is applied; verify catalogue details for substrate specifics. Which chipbreaker does the insert use and what is the benefit? The insert features the 1N‑F57 chipbreaker, which promotes consistent chip formation and safer swarf evacuation, supporting uninterrupted drilling cycles. Can this insert be used in CNC drilling heads and boring bars? Yes — the geometry is intended for indexable drilling and reaming holders; correct clamping and low runout are essential to achieve the expected performance with the insert. How should the correct grade be selected for a specific job? Selection should follow the manufacturer product matrix and machining data; for assistance in matching the P2841S‑1N‑F57 WXP40 to workpiece material and cutting conditions, consult Metav Werkzeuge. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
P2841S-2N-A57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKP25S grade for dependable wear resistance and stable chip formation in drilling and boring operations; order directly via Metav Werkzeuge or request application advice from our consultants. P2841S-2N-A57 WKP25S drill/boring indexable insert — Tiger·tec Silver, for steel & cast iron (Walter Tools) P2841S-2N-A57 WKP25S is a coated carbide indexable insert designed for drilling and boring tasks where consistent edge life and secure chip control are required in steel and cast iron applications Tiger·tec Silver coated carbide for wear resistance WKP25S grade optimised for steel and cast iron 2N-A57 chipbreaker for reliable chip control Suitable for productive drilling and boring operations Longer tool life through optimised coating and grade The insert combines a coated carbide substrate with the Tiger·tec Silver technology to provide enhanced resistance to abrasive and adhesive wear. This results in more consistent cutting-edge condition and a reduction in unscheduled tool changes during series production. The WKP25S grade is formulated for the thermal and mechanical demands of machining steel (ISO group P) and cast iron (ISO group K), making the geometry and coating pairing particularly effective for mixed-production environments. Reduced flank wear and predictable wear progression support process planning and help to maintain component tolerances over longer tool cycles. Precise chip control and stable cutting behaviour The integrated 2N-A57 chipbreaker is engineered to break and evacuate chips reliably in through-hole and bore-cutting operations. This controlled chip formation lowers the risk of chip entanglement and surface damage while preserving coolant flow and tool balance. As a consequence, machining forces remain steady and surface finishes are more consistent, which benefits both manual setups and CNC cycles. The combination of chipbreaker and grade promotes efficient heat dissipation at the cutting edge, which contributes directly to repeatable performance and higher productivity on batches and single-part runs. Easy integration into existing drilling and boring processes The insert’s specification and geometry are compatible with common drill/boring seatings and toolholders used in industrial machining centres. This allows a smooth replacement strategy and minimises machine downtime during routine tool swaps. With its broad material coverage, the insert can be deployed across multiple workpiece types, reducing the need for tool inventory proliferation. For production planners, the result is simplified logistics and improved capacity planning: fewer tool families cover more operations while maintaining component quality and cycle-time targets. For tailored machining recommendations for this Tiger·tec Silver insert and availability details contact Metav Werkzeuge for application-oriented support and ordering information Technical Data SKU: P2841S-2N-A57-WKP25S-WALTER Article: P2841S-2N-A57 WKP25S Product type: Drill/boring indexable insert Manufacturer: Walter Tools Facts Material group: P / K Grade/series: Tiger·tec Silver Chipbreaker: 2N-A57 Special features Coating: coated carbide (Tiger·tec Silver) Suitable for: Steel (P) and Cast iron (K) Range designation: WKP25S FAQ What materials is this insert intended for? The P2841S-2N-A57 WKP25S insert is intended for machining steel (ISO group P) and cast iron (ISO group K), using the Tiger·tec Silver coated carbide to resist wear and maintain edge stability. How does the 2N-A57 chipbreaker affect machining? The 2N-A57 chipbreaker promotes controlled chip formation and evacuation in drilling and boring, improving surface quality and reducing the likelihood of chip-related interruptions with the Walter Tools insert. Is the WKP25S grade suitable for mixed-production environments? Yes, the WKP25S grade offers a balance between wear resistance and toughness, making it appropriate for mixed production of steel and cast iron components where process reliability is essential. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names are mentioned for clarification only and do not imply any affiliation between our company and the trademark holders. The offered item is original, factory-new goods of the manufacturer.
P2841S-2N-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of industrial-grade coating, reliable chip control and broad material compatibility for smoother cycles and fewer tool changes. Order the insert directly via Metav Werkzeuge or consult our technical team for application-specific advice. P2841S-2N-A57 WKP35S Bohr-/Aufbohrwendeschneidplatte — Tiger‑tec Silver, 2N‑A57 chipbreaker, Walter Tools The P2841S-2N-A57 WKP35S is a coated carbide drilling and boring insert from Walter Tools, engineered for productive machining of steel and cast iron in demanding industrial applications. Tiger‑tec Silver coating for long tool life WKP35S grade for stable chip formation 2N‑A57 chipbreaker for reliable chip control Suited for machining steel and cast iron High-performance coating for consistent cutting life The Tiger‑tec Silver technology combines a wear-resistant coating with a robust substrate to deliver predictable performance in continuous production environments. This grade, WKP35S, is a coated carbide formulation optimised for the thermal and abrasive conditions typical when machining steel and cast iron. The result is reduced flank wear and a more constant cutting edge life, which supports planning of tool-change cycles and contributes to lower overall unit costs per component. The insert is designed to cope with the heat generation and chip formation patterns of ISO group P (steel) and K (cast iron) materials, providing an industrially reliable solution for medium- to high-volume turning and boring operations. Effective chip control that stabilises machining processes The integrated 2N‑A57 chipbreaker promotes controlled fragmentation and evacuation of chips, reducing the risk of entanglement and nose damage in drilling and boring operations. By influencing chip curl and breakage behaviour, the geometry helps maintain a steady cutting force and improved contact conditions at the tool edge. This stabilisation translates into fewer interruptions, more consistent surface finish and reduced secondary operations. For shops seeking reproducible cycle times and predictable part quality, the combination of chipbreaker geometry and the TIGER‑tec Silver surface treatment supports reliable process capability across varying batch sizes. Productivity gains through predictable wear and wide applicability Using a carbide insert that is both coated and optimised for P/K materials yields tangible operational benefits: extended tool life under mixed production loads and a broad workpiece material window that reduces the need for tool swaps. The insert’s WKP35S formulation offers stable chip formation and abrasion resistance, which is particularly beneficial in mixed-material series production where setups must remain efficient. Fewer unscheduled tool changes and consistent edge behaviour contribute to improved machine utilisation and can lower per-part machining costs. For production engineers, this means easier process standardisation and improved throughput without sacrificing component accuracy. Contact Metav Werkzeuge for application advice, stock information and cutting data tailored to this Walter Tools insert P2841S-2N-A57 WKP35S Technical Data Article number: P2841S-2N-A57-WKP35S-WALTER Designation: P2841S-2N-A57 ISO designation: P2841S-2N-A57 WKP35S Type: Bohr-/Aufbohrwendeschneidplatte Brand: Walter Tools Facts SKU: P2841S-2N-A57-WKP35S-WALTER Grade: WKP35S Chipbreaker: 2N‑A57 Special features Series: Tiger‑tec Silver Material compatibility: P (steel), K (cast iron) Material of insert: coated carbide FAQ What materials is this insert suitable for? The P2841S-2N-A57 WKP35S is engineered for machining steel (ISO group P) and cast iron (ISO group K), delivering stable performance across both material families. What advantage does the Tiger‑tec Silver series provide? Tiger‑tec Silver offers a wear-resistant coating and a robust substrate, which together extend tool life and improve resistance to thermal and abrasive wear during demanding machining tasks. How does the 2N‑A57 chipbreaker affect machining? The 2N‑A57 geometry promotes controlled chip formation and evacuation, reducing entanglement and helping to maintain steady cutting forces and a consistent surface finish. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools and its logos are the property of their respective owners. Protected trademarks and brand names are cited for clarification only. There is no affiliation implied between our company and the named brands. The offered article is original factory-new merchandise of the manufacturer.
P2841S-2N-A57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold PVD coating and a robust 2N‑A57 chipbreaker to achieve stable chip formation and consistent tool life in demanding drilling and reaming operations; order directly via Metav Werkzeuge or request application support from our technical consultants. P2841S-2N-A57 WSP45G – Indexable insert for drilling and reaming (Walter Tools) P2841S-2N-A57 WSP45G is an indexable insert designed for drilling and reaming applications, optimised for versatile machining of Stahl, rostfreier Stahl and heat‑resistant alloys. Tiger‑tec Gold PVD coating for longer life Versatile for P / M / S material groups Stable cutting edge for productive machining Increase process reliability with a proven coating system The combination of the Tiger‑tec Gold series and the WSP45G grade delivers a PVD‑coated carbide insert engineered for enhanced resistance to flank wear and reliable edge stability. By selecting a coated grade that is formulated for the heat and abrasion typical of drilling, manufacturers benefit from fewer tool changes and more predictable run times — a direct contribution to reduced downtime and improved throughput. The coating and substrate pairing support consistent performance under intermittent contact typical of drilling and reaming cycles. Confident machining across challenging material groups This insert is specified for material groups P / M / S, meaning it is suitable for machining Stahl, rostfreier Stahl and high‑temperature alloys or titanium. The grade’s toughness assists secure chip formation when cutting materials that tend to work‑harden or produce stringy chips. For users less familiar with ISO group codes: P stands for general steel machining, M denotes stainless steels, and S covers heat‑resistant superalloys and titanium — the insert’s composition and geometry are balanced to resist edge breakdown in these contexts, enabling predictable results even in mixed‑material production runs. Optimised chip control and practical integration in drilling setups The 2N‑A57 chipbreaker provides targeted chip control for drilling and reaming operations, reducing the risk of chip jamming and improving coolant access to the cutting zone. As an indexable solution, the insert is simple to fit into compatible drill heads and boring assemblies, allowing quick corner changes and minimal machine downtime. The designation P2841S‑2N‑A57 identifies the specific geometry and chipbreaker combination, helping production planners and purchasers match the insert precisely to holders and machining strategies for consistent component quality. For specific application recommendations or to confirm suitability for a particular component material, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for expert guidance on Walter Tools Tiger‑tec Gold inserts. Technical Data SKU: P2841S-2N-A57-WSP45G-WALTER Product label: Bohr-/Aufbohrwendeschneidplatte P2841S-2N-A57 WSP45G Walter Tools Product type: Indexable insert for drilling and reaming Grade: WSP45G Series: Tiger‑tec Gold Chipbreaker: 2N‑A57 Material designation: P / M / S Manufacturer: Walter Tools UID: P2841S-2N-A57-WSP45G-WALTER Facts Net price: 15.228 Special features PVD‑coated carbide (Tiger‑tec Gold) Suitable for Stahl machining Suitable for rostfreier Stahl machining Suitable for heat‑resistant alloys and titanium (S) Chip control via 2N‑A57 chipbreaker Indexable format for quick seat replacement FAQ What materials can this insert machine effectively? The P2841S-2N-A57 WSP45G insert is specified for the ISO groups P, M and S, so it is suitable for Stahl, rostfreier Stahl and heat‑resistant superalloys or titanium. How does the Tiger‑tec Gold surface treatment benefit drilling operations? Tiger‑tec Gold PVD coating on the WSP45G grade increases resistance to flank wear and helps maintain a stable cutting edge during the thermal stresses common in drilling and reaming. What is the purpose of the 2N‑A57 chipbreaker? The 2N‑A57 chipbreaker promotes controlled chip formation and evacuation in drilling/reaming cycles, reducing the likelihood of chip packing and supporting uninterrupted machining. Is this insert compatible with indexable drill holders? Yes, the insert’s indexable format and the designation P2841S‑2N‑A57 allow straightforward integration into compatible drilling and boring holder systems for rapid replacement. Can this grade be used in mixed‑material production runs? The WSP45G grade’s balance of toughness and wear resistance makes it a practical choice for shops processing batches of Stahl and rostfreier Stahl, improving flexibility without sacrificing tool life. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Markennamen and protected product designations are mentioned solely for explanation and identification purposes. There is no affiliation between Metav Werkzeuge and the referenced brands. The offered article is an original, factory‑new product of the respective manufacturer.
P2841S-2N-A57 WXP40 Wendeplatten - Walter Tools
Take advantage of the WXP40 grade and the 2N-A57 chipbreaker to achieve reliable chip control and predictable edge life in drilling and boring operations; order the insert or consult Metav Werkzeuge for application-specific advice. P2841S-2N-A57 WXP40 — drilling/boring indexable insert with 2N-A57 chipbreaker (Walter Tools) P2841S-2N-A57 WXP40 is a drilling and boring indexable insert designed to manage chips and maintain consistent cutting performance in production environments Uncoated carbide grade WXP40 Chipbreaker geometry 2N-A57 for chip control Compatible with Walter open series inserts Faster, more predictable metal removal with controlled chips The WXP40 grade is an uncoated carbide cutting material intended to deliver steady wear behaviour in interrupted and continuous drilling and boring. Combined with the 2N-A57 chipbreaker, this geometry promotes controlled chip formation, reducing the risk of snarled swarf and tool stoppages. In practical terms, this means fewer unexpected interruptions on the machine, more consistent cycle times and less manual chip clearance; operators benefit from a more predictable process and reduced handling time for produced components. Consistent edge life for reliable production output The insert’s composition and geometry contribute to repeatable edge life under comparable cutting parameters. The open-series design from Walter focuses on practical machining tasks where consistent performance matters more than exotic coatings. For workshops aiming to maintain throughput, the indexable insert’s stability translates to fewer tool changes and lower process variability. When selecting grade and parameters, the product matrix should be consulted to match workpiece material and cutting conditions, ensuring the most cost-effective setup for a given job. Simple identification and integration into tooling systems Identified as P2841S-2N-A57 WXP40, the insert follows conventional designation logic, making it straightforward to match with compatible holder systems and drilling/boring tool bodies. The clear chipbreaker designation aids in choosing the right geometry for chip evacuation needs. Where material specifications are catalogue-dependent, the listing clarifies that further detail is available in the supplier matrix; this supports informed tool selection and reduces the likelihood of mismatches in the toolroom. For specialised materials or unusual cutting conditions, technical advice is available to confirm suitability. Contact Metav Werkzeuge for tailored advice on selecting the correct Walter Tools insert and securing the appropriate geometry and grade for the intended drilling or boring application Technical data Article number: P2841S-2N-A57-WXP40-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P2841S-2N-A57 WXP40 Walter Tools Type: drilling/boring indexable insert Grade: WXP40 Chipbreaker: 2N-A57 Series: Walter cutting grade - open series Material information: catalogue-dependent Core figures No numerical cutting data provided in the product specification Design & special features Designation: P2841S-2N-A57 ISO marking: P2841S-2N-A57 WXP40 Uncoated carbide grade Intended use: drilling and boring indexable insert Series: Walter Schneidstoffsorte - Serie offen FAQ What materials is this insert suitable for? The suitability depends on the material matrix; P2841S-2N-A57 WXP40 is an uncoated carbide grade and its application range should be checked against the Walter product matrix or supplier catalogue. What benefit does the 2N-A57 chipbreaker provide? The 2N-A57 chipbreaker is engineered to shape and break chips during drilling and boring, improving evacuation and reducing swarf-related interruptions with the P2841S-2N-A57 insert. Is the cutting grade coated? No, the WXP40 grade supplied here is an uncoated carbide grade, offering predictable wear characteristics in many general machining tasks. How is the insert identified for replacement or reordering? Use the full designation P2841S-2N-A57 WXP40 and the SKU when reordering to ensure correct geometry and grade matching. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P2841S-2N-E57 WKP25S Wendeplatten - Walter Tools
Take advantage of a proven coated-carbide grade and a dedicated chipbreaker geometry for reliable drilling and bore-enlarging in steel and cast iron; order the insert directly via Metav Werkzeuge or consult the specialists for application support. P2841S-2N-E57 WKP25S drill/boring indexable insert – Tiger·tec Silver coating for steel and cast iron | Walter Tools The P2841S-2N-E57 WKP25S is a coated carbide indexable insert engineered for efficient drilling and bore-enlarging in steel and cast iron. Tiger·tec Silver coating for extended tool life Optimised chip control geometry 2N‑E57 Suited to steel and cast iron machining Coated carbide WKP25S for high productivity Durable coating and reliable cutting performance The combination of the Tiger·tec Silver series and the WKP25S grade provides a coated carbide solution designed for sustained performance in demanding metalcutting. The coating technology reduces abrasive wear and helps maintain a stable cutting edge through longer tool life, which contributes to fewer interruptions and more predictable production cycles. As a result, process stability and component repeatability are improved when working in materials typical for ISO group P and K. Controlled chip formation for safer drilling cycles The insert’s 2N‑E57 chipbreaker geometry is tailored to the dynamics of drilling and bore-enlarging operations. By guiding and segmenting swarf, the geometry reduces the risk of long chips and improves evacuation from the hole, which in turn lowers the likelihood of recut marks or tool jamming. This precise chip control supports consistent surface finish and minimises cycle-time variance for batches where repeatability matters. Application range and production benefits Designed primarily for unalloyed and alloyed steel and for cast iron, the cutting grade addresses the typical heat and chip behaviour of these groups. Using this indexable insert in a compatible drill or boring head helps reduce the number of tool changes and simplifies inventory by favouring a universal grade for common materials. Procurement and tool management benefit from the insert’s predictable wear behaviour, making it a pragmatic choice for workshops aiming for steady throughput and lower process variability. For advice on integrating Tiger·tec Silver inserts into existing tool systems or to discuss the P2841S-2N-E57 WKP25S for specific machining tasks, contact Metav Werkzeuge for application guidance and availability. Technical data SKU: P2841S-2N-E57-WKP25S-WALTER Product label: Bohr-/Aufbohrwendeschneidplatte P2841S-2N-E57 WKP25S Walter Tools Product type: drill/boring indexable insert Facts Grade: WKP25S Chipbreaker: 2N‑E57 Series: Tiger·tec Silver Material code: P / K Special features Coated carbide cutting grade Designed for steel (P) and cast iron (K) Optimised for drilling and bore-enlarging operations Manufacturer: Walter Tools FAQ Which materials is this insert designed for? The P2841S-2N-E57 WKP25S insert is specified for ISO groups P (steel) and K (cast iron), covering unalloyed and alloyed steels as well as typical cast-iron types. What does the 2N‑E57 chipbreaker achieve? The 2N‑E57 geometry promotes controlled chip segmentation and evacuation during drilling and bore-enlarging, reducing the risk of long swarf and improving surface consistency for the machined bore. What are the main benefits of Tiger·tec Silver on this grade? Tiger·tec Silver coating increases abrasive-wear resistance and helps sustain a sharp cutting edge under thermal and mechanical load, resulting in longer usable life for the insert in repetitive operations. Can this insert be used for stainless steel? Stainless steel (rostfrei) is not specified among the intended application groups for the P2841S-2N-E57 WKP25S; the grade is optimised for steel and cast iron according to its designation. Which product designation should be quoted when ordering spare inserts? Quote the full SKU or designation — P2841S-2N-E57 WKP25S — together with the manufacturer Walter Tools to ensure the correct grade and chipbreaker are supplied. Die Walter AG (brand presentation: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names are the property of their respective owners. The supplied article is original, factory‑new goods of the manufacturer. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
P2841S-2N-E57 WKP35S Wendeplatten - Walter Tools
The combination of Tiger‑tec Silver coating and the WKP35S carbide grade ensures extended tool life and consistent performance in steel and cast iron machining; this improves uptime and reduces tooling costs. Order the insert directly via Metav Werkzeuge or consult the technical team for geometry and application advice. P2841S-2N-E57 WKP35S – Walter Tools drilling/boring indexable insert with Tiger‑tec Silver coating and 2N‑E57 chipbreaker A P2841S-2N-E57 WKP35S indexable insert engineered for productive drilling and bore‑enlarging operations in steel and cast iron, offering reliable wear resistance and controlled chip formation. Tiger‑tec Silver coating technology WKP35S coated carbide grade 2N‑E57 chipbreaker for stable chips Optimised for steel and cast iron applications Longer tool life from advanced coating and grade The combination of Tiger‑tec Silver coating and the WKP35S coated carbide grade is designed to resist abrasive and adhesive wear commonly encountered when machining steel and cast iron. The surface treatment reduces flank and crater wear, which translates into fewer tool changes and more consistent component tolerances. For production environments this means improved machine uptime and predictable tool consumption, supporting leaner tool inventories and lower unit costs per component. Predictable chip control for uninterrupted production Equipped with the 2N‑E57 chipbreaker, the insert produces short, consistent chips that are easy to evacuate from the cutting zone. Stable chip formation reduces the risk of workpiece marking and spindle interruptions, resulting in better surface quality and fewer secondary operations. The chip geometry is tailored to the thermal and mechanical conditions of P and K workpiece groups, enabling secure feeding and steady cutting forces during drilling and bore enlargement. Clear application scope and process benefits Designed for the ISO P and K material groups, this insert suits a wide range of unalloyed and alloyed steel grades as well as various cast iron types. The geometry supports efficient material removal while maintaining dimensional stability, making it appropriate for series production and demanding single‑part machining alike. Integrating this indexable insert into existing toolholders and standard drilling cycles is straightforward, delivering immediate gains in process reliability and machining throughput. For application advice or to secure supply of this Walter Tools insert with Tiger‑tec Silver performance, contact Metav Werkzeuge for technical consultancy and order placement. Technical data Article number: P2841S-2N-E57-WKP35S-WALTER SKU: P2841S-2N-E57-WKP35S-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte (drilling/boring indexable insert) Manufacturer: Walter Tools Grade/series: WKP35S, Tiger‑tec Silver Chipbreaker: 2N‑E57 Facts Material group suitability: P (steel) Material group suitability: K (cast iron) Coating: Tiger‑tec Silver (coated carbide) Designation: P2841S-2N-E57 WKP35S UID: P2841S-2N-E57-WKP35S-WALTER Special features Coated carbide grade WKP35S Optimised chip control geometry Intended for drilling and bore enlargement applications Balanced for wear resistance and edge stability FAQ Which materials is this insert suitable for? The P2841S-2N-E57 WKP35S insert is formulated for ISO groups P and K, i.e. a range of steel grades and cast iron materials. What coating and grade are used on this insert? This indexable insert uses the Tiger‑tec Silver coating and the WKP35S coated carbide grade for enhanced wear resistance and thermal stability. How does the 2N‑E57 chipbreaker improve machining? The 2N‑E57 chipbreaker on the P2841S-2N-E57 WKP35S promotes short, controllable chips, reducing interruptions and improving surface finish during drilling and bore enlargement. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. The mentioned brand is cited solely for explanation; the offered article is an original, factory‑new product of the manufacturer.
P2841S-2N-E57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a dedicated 2N‑E57 chipbreaker, and broad material capability for dependable drilling and bore‑enlargement results; order the insert directly via Metav Werkzeuge or consult the Metav team for tailored recommendations. P2841S-2N-E57 WSP45G drilling/bore‑enlargement indexable insert — Walter Tools, Tiger·tec Gold P2841S-2N-E57 WSP45G is a coated indexable insert designed for drilling and bore‑enlargement operations, offering high process stability and versatile performance across demanding workpiece materials. Tiger·tec Gold PVD coating for long tool life Designed for steels, stainless steel and superalloys Stable cutting edge for reliable chip control Suitable for drilling and bore‑enlargement operations Durable coating for extended productivity The combination of the Tiger·tec Gold coating and the WSP45G grade brings enhanced wear resistance and thermal stability to the cutting edge. The PVD‑based surface treatment reduces flank wear and supports consistent tool life in interrupted or continuous drilling cycles. For production environments where tool‑change frequency affects throughput, the coated grade contributes to fewer interventions and steadier cycle times while maintaining component tolerances. Geometry engineered for consistent chip control The dedicated 2N‑E57 chipbreaker geometry provides controlled chip formation during bore enlargement, reducing clogging and promoting stable evacuation in constrained cavities. The insert’s cutting edge geometry stabilises the cutting forces and lowers the risk of built‑up edge on sticky materials, which translates into more reliable surface finish and dimensional consistency on the bore wall. This engineered geometry is particularly beneficial where repeatability and minimising rework are priorities. Broad material capability that eases tool planning Rated for material groups P / M / S, the insert is suited to unalloyed and alloyed steels, rostfreier Stahl (stainless steel) and heat‑resistant superalloys or titanium. The WSP45G grade balances toughness and hardness to withstand the heat and mechanical stress typical of these materials, enabling one insert type to cover multiple workpiece families. Using a single, versatile grade reduces tool inventory complexity and eases production planning for mixed‑material batches. Process reliability and operational efficiency Designed for stable edge retention and predictable wear behaviour, the insert supports higher process safety and consistent surface quality in holemaking. The stable cutting edge and optimised substrate composition of the WSP45G grade help to maintain cutting performance under challenging conditions, making the insert a practical choice where uptime, reproducibility and part quality are critical. Integration into standard drilling toolholders is straightforward, supporting rapid tool changes and minimal setup time. For selection advice or to match the P2841S‑2N‑E57 WSP45G insert to specific toolholders and machining parameters, contact Metav Werkzeuge — email info@metav-werkzeuge.com or phone +49 2822 7131930 to discuss application details and availability. Technical data SKU: P2841S-2N-E57-WSP45G-WALTER Designation: P2841S-2N-E57 ISO designation: P2841S-2N-E57 WSP45G Product type: Drilling/bore‑enlargement indexable insert Grade: WSP45G Series: Tiger·tec Gold Manufacturer: Walter Tools Facts Material groups: P / M / S Applicable materials: Steel; Stainless steel; Superalloys/Titanium Special features Coating technology: Tiger·tec Gold (PVD) Chipbreaker: 2N‑E57 Application: Drilling and bore‑enlargement Substrate: Coated cemented carbide Main advantages: Stable cutting edge; broad material coverage FAQ Which materials are suitable for this insert? The P2841S-2N-E57 WSP45G insert is engineered for material groups P, M and S — that is, steels, rostfreier Stahl (stainless steel) and heat‑resistant superalloys or titanium — offering reliable performance across these families. What is the benefit of the Tiger·tec Gold grade? Tiger·tec Gold provides PVD‑enhanced wear resistance and thermal stability; when used with the WSP45G grade, it extends tool life and helps maintain consistent cutting conditions during drilling and bore enlargement. How does the 2N‑E57 chipbreaker improve machining? The 2N‑E57 chipbreaker promotes controlled chip formation and evacuation in bore operations, reducing the risk of chip packing and improving surface finish and dimensional repeatability. Is the insert suitable for interrupted cuts and varying feed rates? Yes, the WSP45G grade combines toughness with wear resistance to tolerate intermittent engagement and variable feeds, supporting process stability in practical production scenarios. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no connection between our company and the named brands. The offered article is original, factory‑new goods from the manufacturer.
P2841S-2N-E57 WXP40 Wendeplatten - Walter Tools
Take advantage of the insert’s combination of precise chip control and wear-resistant uncoated carbide to maintain consistent bore quality and predictable tool life; order directly via Metav Werkzeuge or consult the team for application advice. P2841S-2N-E57 WXP40 boring/counterboring indexable insert by Walter Tools P2841S-2N-E57 WXP40 is a purpose-designed boring and counterboring indexable insert for precision metalcutting tasks in production environments P2841S-2N-E57 insert, chipbreaker 2N-E57 Uncoated carbide grade WXP40 For boring and counterboring operations Walter Tools open-series cutting grade Consistent bore quality through controlled cutting geometry The P2841S-2N-E57 WXP40 insert is engineered to deliver repeatable dimensional accuracy in internal turning and counterboring operations. The combination of the chipbreaker 2N-E57 geometry and the WXP40 uncoated carbide grade reduces the tendency for irregular chip formation, which in turn supports stable cutting forces and predictable surface finishes. In practice, this means fewer rework cycles and more reliable first-pass accuracy when integrating the insert into established machining cycles. Improved efficiency with predictable chip evacuation and tool life A clear manufacturing benefit of the chipbreaker 2N-E57 is its effective chip control, which minimises interruptions from chip entanglement and reduces heat concentration at the cutting edge. The WXP40 grade—an uncoated cemented carbide designed for general-purpose applications—offers a balance between hardness and toughness that supports longer service intervals under appropriate cutting conditions. Explaining the trade-off: uncoated carbide avoids risks associated with coating delamination in certain interrupted cuts while maintaining dependable wear resistance for many steels and non-ferrous materials. Selection criteria and integration into machining processes Process planners are advised to verify material compatibility against the manufacturer’s product matrix before implementation; the cutting grade’s suitability should be matched to workpiece material and cutting conditions. The insert’s designation and ISO reference facilitate easy cross-referencing in tool lists and CAM libraries, enabling planners to standardise operations and reduce setup variability. Where intermittent cutting or variable depths of cut are common, the open-series Walter grade gives flexibility for conservative parameter windows that favour process stability. Practical handling benefits and inventory considerations From a workshop logistics perspective, the insert’s clear designation and series coding simplify stock management and replacement planning. The standardised geometry enables straightforward toolholder selection and minimises spindle downtime during index changes. Emotionally, operators tend to prefer toolsets that behave predictably in daily use; the familiar geometry and established carbide grade provide that reassurance while supporting efficient throughput and consistent surface quality across batches. Contact Metav Werkzeuge for tailored application advice on Walter Tools WXP40 inserts or to request procurement details — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: P2841S-2N-E57-WXP40-WALTER Article name: Bohr-/Aufbohrwendeschneidplatte P2841S-2N-E57 WXP40 Walter Tools Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte Item designation: P2841S-2N-E57 WXP40 Core data Net price: 13.50 UID: P2841S-2N-E57-WXP40-WALTER Materials and features Grade: WXP40 (uncoated carbide) Chipbreaker: 2N-E57 Series: Walter Schneidstoffsorte - Serie offen Material reference: Katalogabhängig ISO designation: P2841S-2N-E57 WXP40 Application note: Suitability to be checked against product matrix FAQ What materials is this insert suitable for? The insert’s WXP40 grade is an uncoated carbide offering general-purpose performance; suitability for specific materials should be confirmed using the product matrix and machining parameters. How does the chipbreaker 2N-E57 influence machining? The 2N-E57 chipbreaker promotes controlled chip formation and evacuation, which helps maintain stable cutting forces and consistent bore quality during boring and counterboring. Is the insert coated or uncoated? This insert is supplied in an uncoated carbide grade (WXP40), chosen for its balance of toughness and wear resistance in varied conditions. How should toolholders be selected for this insert? Select a toolholder compatible with the insert geometry and ISO designation P2841S-2N-E57 to ensure correct seating and maximal repeatability during index changes. What is the recommended step if cutting performance varies? If performance varies, review cutting parameters, verify workpiece material against the product matrix, and consider adjusting feeds and speeds to match the insert’s intended application range. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalcutting and forms part of the Swedish Sandvik group. Protected trademarks and trade names belong to their respective owners; brand names are used solely for explanation.
P2841S-2N-E67 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKP35S grade for consistent cutting performance in steel and cast iron; the engineered 2N‑E67 chipbreaker ensures controlled swarf formation and reliable machining. Order directly via Metav Werkzeuge or request application advice from their consultants. P2841S-2N-E67 WKP35S indexable insert for drilling/reaming — Walter Tools The P2841S-2N-E67 WKP35S is an indexable insert engineered for high-productivity drilling and reaming operations in steel and cast iron, offering a balance of wear resistance and chip control. Tiger·tec Silver coating for extended tool life WKP35S grade for robust cutting performance Optimised 2N‑E67 chipbreaker for controlled chips Prolonged tool life through advanced coating The insert uses the Tiger·tec Silver coating technology combined with the WKP35S coated‑carbide grade to improve wear resistance and maintain edge stability under cyclic loads. Coating reduces adhesion and thermal impact during interrupted or continuous cutting, which translates to longer service intervals and fewer indexings. For workshops seeking to reduce tool change frequency while keeping consistent component quality, the coated grade provides a measurable improvement in tool life without compromising productivity. Predictable chip control for safer machining The 2N‑E67 chipbreaker geometry is designed to produce short, manageable chips across typical drilling and reaming conditions in the targeted material groups. By controlling chip shape and evacuation, the breaker reduces the risk of chip entanglement and workpiece surface damage. This results in more predictable machining cycles and improved process security; operators will benefit from fewer stoppages and more stable cycle times when using the correctly matched tool holder and cutting parameters. Versatility in steel and cast iron applications Developed for ISO groups P (steel) and K (cast iron), the insert is optimised for the thermal and abrasive demands of these materials. The grade accommodates the high heat generation common when machining steels while its coating and geometry resist the abrasive wear typical of cast iron. The outcome is consistent surface finishes and dimensional repeatability, especially in series production where component uniformity and tool reliability are decisive for throughput and downstream processes. Practical advantages for production workflows As an indexable solution from Walter Tools, this insert supports quick replacements and consistent positioning, aiding repeatability across batches. The combination of a proven coating system and a specialised chipbreaker contributes to predictable tool scheduling and easier integration into existing tool management routines. For manufacturing environments prioritising uptime and consistent part quality, the insert helps maintain stable machining windows while simplifying inventory by covering both steel and cast iron operations with a single grade. For machining tasks where dependable performance in steel and cast iron is essential, contact Metav Werkzeuge for tailored application advice and current availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: P2841S-2N-E67-WKP35S-WALTER Designation: P2841S-2N-E67 WKP35S Product type: indexable insert for drilling/reaming Core data Grade: WKP35S Coating technology: Tiger·tec Silver Chipbreaker: 2N‑E67 Applicable material groups: P (steel), K (cast iron) Features and applications Brand: Walter Tools Material of insert: coated carbide Suitable for: steel and cast iron Series: Tiger·tec Silver FAQ Is this insert suitable for stainless steel applications? The P2841S-2N-E67 WKP35S insert is specified for ISO groups P and K (steel and cast iron); stainless steel is not listed as a designated application for this grade. What is Tiger·tec Silver and why does it matter? Tiger·tec Silver is a coating technology used on the WKP35S grade that improves wear resistance and reduces heat-related edge degradation, which helps the insert deliver longer life and more consistent performance in demanding cycles. How does the 2N‑E67 chipbreaker improve machining? The 2N‑E67 geometry is optimised to produce short, controlled chips, enhancing evacuation and reducing the likelihood of built-up edge or swarf-related interruptions when machining steel and cast iron. For which material groups is this insert intended? According to the designation, the insert is intended for ISO group P (steel) and ISO group K (cast iron), making it a versatile choice for mixed production environments. How does the WKP35S grade compare with other grades? WKP35S is a coated‑carbide grade within the Tiger·tec Silver family that balances wear resistance and toughness for robust cutting performance in steel and cast iron, offering a compromise between tool life and cutting-edge stability for general production tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanatory purposes only. There is no affiliation between our company and the named brands; the offered article is an original, factory-new product of the manufacturer.
P2841S-2N-E67 WSP45G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WSP45G grade for consistent edge stability and reliable chip control across steel, stainless steel and heat‑resistant alloys; these properties combine to reduce downtime and extend tool life. Order the insert directly via Metav Werkzeuge or consult the specialists for application advice. P2841S-2N-E67 WSP45G — indexable drill/reamer insert, Tiger‑tec Gold, Walter Tools P2841S-2N-E67 WSP45G is an indexable drill/reamer insert designed for expanded holemaking operations in steels, stainless steels and high‑temperature alloys Tiger‑tec Gold PVD coating Suitable for P / M / S materials Chipbreaker design 2N‑E67 Stable, coated cemented carbide grade High‑performance coating for longer tool life The Tiger‑tec Gold PVD coating represents the main wear‑resistance feature and is selected for its ability to maintain a stable cutting edge under cyclic thermal and mechanical load. In practice, the coating reduces flank wear and supports predictable tool life, which translates directly into fewer tool changes and improved process reliability. The combination of coating and substrate provides a balance between wear resistance and toughness suitable for mixed production runs. Versatile material capability cuts setup variety Engineered for the ISO groups P / M / S, the insert covers unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys/titanium alike. This versatility reduces the need for multiple tool types and simplifies inventory control. The WSP45G grade is optimised to support secure chip formation in tough materials, improving surface finish and reducing the risk of built‑up edge during interrupted or continuous drilling and reaming cycles. Geometry and chip control that stabilise machining The 2N‑E67 chipbreaker geometry has been developed to control swarf evacuation and moderate cutting forces during hole enlargement. Controlled chip formation reduces vibration and enhances bore quality, yielding more consistent diameters and better cylindricity. The indexable insert form permits rapid indexation and replacement, so toolholders return to cutting condition with minimal downtime. Process benefits for production and maintenance Adopting this insert in production lines contributes to higher throughput via longer cutting intervals and fewer interventions. The combination of coated cemented carbide and chipbreaker design allows for stable machining at practical cutting speeds, supporting a favourable cost‑to‑performance ratio. For operations seeking predictable results across varied materials, the Walter Tools solution is a pragmatic choice that aligns quality with economical manufacturing. For ordering or machining guidance with the Tiger‑tec Gold WSP45G insert, contact Metav Werkzeuge for tailored advice and delivery options: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: P2841S-2N-E67-WSP45G-WALTER SKU: P2841S-2N-E67-WSP45G-WALTER Product type: indexable drill/reamer insert Grade: WSP45G Series: Tiger‑tec Gold Facts Material groups: P / M / S Chipbreaker: 2N‑E67 Manufacturer: Walter Tools UID: P2841S-2N-E67-WSP45G-WALTER Special features PVD‑coated cemented carbide Suitable for steel, stainless steel, superalloys and titanium Designed for stable chip control and edge life Indexable geometry for quick replacement FAQ What materials are suitable for this insert? The P2841S-2N-E67 WSP45G insert is suitable for ISO groups P (steel), M (stainless steel) and S (heat‑resistant superalloys/titanium). What benefit does the Tiger‑tec Gold coating provide? Tiger‑tec Gold on the WSP45G grade improves wear resistance and maintains a stable cutting edge, resulting in longer tool life and more consistent machining. Is the chipbreaker 2N‑E67 suitable for hole enlargement operations? Yes, the 2N‑E67 chipbreaker is configured to control chips and cutting forces during drilling and reaming, enhancing bore quality and swarf evacuation. Can this insert be indexed during production to reduce downtime? The indexable format of the P2841S-2N-E67 enables rapid indexation and replacement, minimising intervention time and sustaining productive cycles. Which brand manufactures this insert and what series does it belong to? The insert is a Walter Tools product and belongs to the Tiger‑tec Gold series, grade WSP45G (SKU P2841S-2N-E67-WSP45G-WALTER). The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision cutting tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are used solely for explanation; there is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
P2841S-2N-E67 WXP40 Wendeplatten - Walter Tools
Benefit from WXP40 uncoated carbide reliability and the 2N‑E67 chipbreaker for consistent chip control and productive boring cycles; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. P2841S-2N-E67 WXP40 boring/reaming indexable insert by Walter Tools — uncoated carbide for productive metalcutting P2841S-2N-E67 WXP40 is a purpose-built insert for precision bore finishing and in-process enlarging, designed for stable chip formation in demanding production environments. Uncoated carbide grade WXP40 Chipbreaker 2N‑E67 for reliable chips Designed for boring and reaming operations Walter Tools manufacturing quality Higher throughput for rotating boring operations The insert delivers productive machining by combining an uncoated carbide substrate with a dedicated chipbreaker (2N‑E67) that promotes consistent chip segmentation. This design reduces the risk of stringing and minimises interruptions, which in turn supports longer uninterrupted cycle times. For workshops aiming to raise output without complex process changes, the geometry provides a straightforward route to improved material removal rates and predictable results. Clear selection and material guidance for safe use The cutting grade WXP40 is specified as an uncoated hardmetal grade; suitability must be checked against the product matrix for each application. The open series construction is intended to cover a broad range of workpiece materials when matched correctly. Where material recommendations are unclear, evaluate the cutting parameters and consult the product matrix — the insert is optimised for stable chip formation rather than for coated wear resistance, making it appropriate where edge stability on an uncoated grade is preferred. Practical handling and process advantages on the shop floor Inserts of this type offer simple handling and rapid replacement in modular boring heads, reducing downtime during tool changes. The P2841S-2N-E67 geometry supports precise bore outcomes and is compatible with standard clamping systems for indexable inserts. Clear labelling and a consistent grade designation simplify inventory management and help maintain process repeatability across batches, supporting both small-series flexibility and larger production runs. Discuss specific machining parameters and suitability with Metav Werkzeuge — request tailored application advice for the Walter Tools P2841S-2N-E67 WXP40 insert via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: P2841S-2N-E67-WXP40-WALTER SKU: P2841S-2N-E67-WXP40-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte ISO designation: P2841S-2N-E67 WXP40 Facts Grade: WXP40 Chipbreaker: 2N‑E67 Series: Walter Schneidstoffsorte - Serie offen Special features Coating: uncoated hardmetal Material: Katalogabhängig Manufacturer: Walter Tools Application note: Verify workpiece suitability via the product matrix FAQ What materials is this insert suitable for? The P2841S-2N-E67 WXP40 insert is an uncoated hardmetal grade; suitability for specific workpiece materials should be checked against the Walter Tools product matrix before use. Is the 2N‑E67 chipbreaker suitable for finishing bores? Yes — the 2N‑E67 chipbreaker is designed to promote stable chip segmentation during boring and reaming operations, supporting precise bore finishes when cutting conditions are correctly set. Can this insert be used in standard modular boring heads? The insert format is intended for indexable boring systems and is compatible with standard clamping setups; confirm seat geometry and clamping specifications before installation. How does WXP40 compare to coated grades? WXP40 is an uncoated hardmetal grade prioritising edge stability and chip control; coated grades may offer additional wear resistance for abrasive applications, so choose based on the specific process demands. Where can additional application data for this insert be obtained? Technical application information and parameter recommendations for the P2841S-2N-E67 WXP40 can be requested from Metav Werkzeuge or obtained from Walter Tools documentation. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
P2841S-2N-F57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating and the WKP35S grade for enhanced wear resistance and stable chip control in drilling and bore-enlarging operations. Order the P2841S-2N-F57 WKP35S directly via Metav Werkzeuge or ask the consultants for tailored process advice. P2841S-2N-F57 WKP35S Drilling/Reaming Indexable Insert — Tiger·tec Silver for Steel & Cast Iron | Walter Tools The P2841S-2N-F57 WKP35S is a drilling/reaming indexable insert designed for high-performance machining of steel and cast iron in production and job-shop environments Tiger·tec Silver coated carbide grade WKP35S Optimised 2N‑F57 chipbreaker for stable chips Designed for steel and cast iron machining High process reliability for consistent results Maximised wear resistance for productive drilling The combination of the Tiger·tec Silver coating and the WKP35S coated carbide provides a durable cutting edge that resists abrasive wear during plunge and peripheral cutting. The coating reduces adhesion and heat absorption, which lengthens tool life and lowers frequency of index changes. For operations where predictable performance matters, the insert offers a measurable improvement in uptime and cycle consistency, translating into fewer interruptions and a smoother production flow. The design supports repeatable drilling and bore-enlarging cycles with reduced edge degradation. Reliable chip control for steel and cast iron The 2N‑F57 chipbreaker is engineered to produce short, controlled chips when machining materials classified as P (steel) and K (cast iron) under ISO 513. Stable chip formation reduces the risk of chip entanglement and improves surface finish in through-hole and interrupted-section cuts. The geometry is particularly effective with the thermal and mechanical behaviour typical of steels and cast irons, helping to maintain consistent cutting conditions and reduce the need for manual chip handling during longer runs. Consistent process performance and cost-efficiency A focus on process reliability means fewer unplanned tool changes and steadier part quality. The coated carbide grade and chip geometry support extended tool life and consistent dimensional results, which improves first-pass yield and lowers effective tooling cost per component. Where production schedules demand repeatability, the insert helps maintain cycle times and contributes to overall machining economy. The combination of wear resistance and chip control is aimed at delivering both productivity and dependable performance in series production. Practical integration and selection guidance The insert is suitable for drilling and bore-enlarging operations in mixed-production shops and industrial cells that process steels and cast irons. Selection should consider machine rigidity, coolant strategy and cutting data tailored to the specific workpiece grade; the insert performs best under stable clamping and consistent feed rates. When choosing the insert for new applications, refer to machining tables for coated carbide grades and test with representative workpieces to validate feeds and speeds. For additional application data or geometry matching, Metav Werkzeuge provides specialist guidance and can advise on optimal cutting parameters. Discuss integration and availability with Metav Werkzeuge for Walter Tools Tiger·tec Silver inserts — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored application support Technical data SKU: P2841S-2N-F57-WKP35S-WALTER Designation: P2841S-2N-F57 WKP35S Type: Bohr-/Aufbohrwendeschneidplatte Facts Series: Tiger·tec Silver Chipbreaker: 2N‑F57 Suitable for materials: P / K (Steel / Cast iron) Special features Coating: Tiger·tec Silver Carbide grade: WKP35S Application: Drilling / reaming (bore-enlarging) Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The P2841S-2N-F57 WKP35S is designed for machining materials in ISO groups P and K, specifically steel and cast iron, benefiting from the WKP35S grade and Tiger·tec Silver coating. How does the 2N‑F57 chipbreaker improve machining? The 2N‑F57 chipbreaker produces short, controlled chips that improve chip evacuation and surface finish when the insert is used in drilling and bore-enlarging operations in steel and cast iron. Is the insert suitable for interrupted cutting conditions? Yes, the coated carbide grade and reinforced edge geometry provide good resistance to the impacts often encountered in interrupted drilling cycles, supporting consistent performance. Which series does the insert belong to and what is the advantage? This insert is part of the Tiger·tec Silver series, offering improved wear resistance and thermal stability compared with uncoated grades, which helps extend index life. Can cutting data be provided for initial trials? Cutting data recommendations are best validated on the specific machine and workpiece; reference values for the Tiger·tec Silver grade and 2N‑F57 geometry are available and can be adapted for trial cuts Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
P2841S-2N-F57 WSP45G WSP45G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the WSP45G grade delivers durable cutting performance and stable chip control for drilling and boring operations. The robust 2N-F57 chipbreaker and suitability for P / M / S material groups ensure consistent production results. Order the insert directly via Metav Werkzeuge or consult their specialists for application support. P2841S-2N-F57 WSP45G — Drilling/boring indexable insert, Tiger·tec Gold, Walter Tools The P2841S-2N-F57 WSP45G is a Tiger·tec Gold-coated drilling/boring indexable insert designed for precision machining of steel, stainless steel and heat‑resistant alloys in industrial metalworking. Tiger·tec Gold PVD coating for long tool life Versatile P/M/S material range Stable cutting edge with 2N-F57 chipbreaker Insert type P2841S-2N-F57 for drilling/boring Long-lasting coating for higher productivity The insert features the Tiger·tec Gold PVD technology combined with a WSP45G grade, a PVD-coated cemented carbide formulation engineered for toughness and wide applicability. This coating reduces flank wear and improves thermal resistance, which translates into extended tool life and fewer indexings in batch production. For shops focused on cycle-time reliability, the enhanced wear resistance contributes to more predictable tool schedules and reduced downtime, supporting continuous machining workflows. Geometry and chip control that stabilise cycles Equipped with the chipbreaker 2N-F57, the geometry is configured to promote reliable chip formation during drilling and boring operations. The controlled chip flow lowers the risk of built-up edge and reduces vibration at the cutting zone, which helps maintain dimensional accuracy and surface finish. The insert’s geometry is particularly beneficial where intermittent or deep-hole conditions challenge edge stability, offering consistent cutting behaviour across repeated cycles. Broad material compatibility for flexible application planning Rated for the P / M / S ISO groups, the design is suitable for machining steel, stainless steel and superalloys/titanium, making it a versatile choice for job shops and production departments that handle mixed batches. The combination of a tough substrate and a wear‑resistant coating supports performance in temperature‑critical cuts and when machining materials that tend to work‑harden. For operations seeking a single insert solution to reduce tooling variety, this option balances robustness with predictable performance. For high‑performance drilling and boring with Walter Tools’ Tiger·tec Gold inserts, contact Metav Werkzeuge for tailored recommendations and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: P2841S-2N-F57-WSP45G-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P2841S-2N-F57 WSP45G Walter Tools Manufacturer: Walter Tools Key figures Grade: WSP45G Series: Tiger·tec Gold Material groups: P / M / S Chipbreaker: 2N-F57 Designation: P2841S-2N-F57 WSP45G Design / Special features PVD-coated cemented carbide grade Tough, versatile coating technology Optimised chipbreaker for drilling/boring Suitable for steel, stainless steel, superalloys/titanium FAQ Which materials can be machined with this insert? The P2841S-2N-F57 WSP45G insert from Walter Tools is specified for ISO groups P, M and S, meaning it is suitable for machining steel, stainless steel and heat‑resistant superalloys/titanium. What coating and grade does the insert use? The insert uses the Tiger·tec Gold PVD technology and the WSP45G grade, providing enhanced wear resistance and thermal stability for demanding cuts. What is the purpose of the 2N-F57 chipbreaker? The 2N-F57 chipbreaker is designed to ensure controlled chip formation during drilling and boring, improving chip control and helping to maintain edge stability under varying cutting conditions. Is this insert suited for serial production and mixed batches? Yes. The combination of a tough substrate and the Tiger·tec Gold coating offers consistent wear behaviour, making the insert well suited to serial production and workshops handling mixed materials. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only and do not indicate any affiliation between Metav Werkzeuge and the trademark holders. The offered item is an original, factory-new product from the manufacturer.
P2841S-2N-F57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control, robust uncoated carbide geometry and the Walter open-series design for steady drilling and boring performance; order directly via Metav Werkzeuge or contact our consultants for material-matrix verification. P2841S-2N-F57 WXP40 – Drill/Boring Indexable Insert (Walter Tools) P2841S-2N-F57 WXP40 is an indexable insert designed for drilling and bore-enlargement operations, offering a defined chipbreaker and an uncoated cemented-carbide grade for reproducible cutting performance P2841S-2N-F57 insert, WXP40 grade Chipbreaker 2N-F57 for consistent chip control Uncoated cemented carbide for robust cutting Suited to drilling and boring applications Higher throughput through stable cutting geometry The combination of the WXP40 cemented-carbide grade and the 2N-F57 chipbreaker is engineered to deliver predictable tool life and fewer process interruptions. The uncoated carbide substrate provides consistent edge behaviour under a range of feeds and depths typical for drilling and bore-enlargement tasks, which supports higher machine utilisation. By stabilising the cutting edge and reducing unexpected wear patterns, this insert helps to keep cycle times steady and regrinding schedules predictable, contributing to efficient production planning. Controlled chips, cleaner processes A defined chipbreaker such as 2N-F57 improves chip control during holemaking, which reduces the risk of built-up edge and eases chip evacuation from the cutting zone. Better chip formation translates into fewer stoppages for manual cleaning and lower risk of workpiece damage, particularly in stacked or deep-hole operations. The insert’s geometry is intended to produce short, manageable chips under the correct cutting parameters, supporting safer and more reliable machining cycles on both conventional and CNC equipment. Practical selection and compatibility guidance Material suitability for this insert should be confirmed against the Walter product matrix. The insert is supplied in the open series and is an indexable insert intended for conventional drilling and boring tool systems. When selecting the correct grade and geometry, compare the WXP40 features with the specific workpiece metal, required surface finish and cycle demands. If a change in cutting data or holder type is planned, consult the technical matrix to ensure compatibility and to determine optimal feeds and speeds for the chosen application. Operational benefits and process reliability Using an insert from the Walter open series supports straightforward inventory management: standard grades like WXP40 are aimed at broad applicability and reliable edge behaviour. The insert’s uncoated carbide construction simplifies reconditioning and inspection routines while providing consistent performance across batches. For procurement and process integration, the result is predictable delivery of parts and a dependable baseline for continuous improvement activities in the production cell. Request material-matrix verification and procurement assistance from Metav Werkzeuge — contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 to confirm suitability and availability Technical data SKU: P2841S-2N-F57-WXP40-WALTER Designation: P2841S-2N-F57 WXP40 Product type: Drill/boring indexable insert Grade: WXP40 Chipbreaker: 2N-F57 Series: Walter Schneidstoffsorte - Serie offen Material: Katalogabhängig Facts No numerical cutting data provided No dimensions specified Material suitability to be checked in product matrix Special features Uncoated cemented carbide (unbeschichtetes Hartmetall) Defined chipbreaker geometry 2N-F57 Open series grade for broad application Intended for drilling and bore-enlargement operations FAQ What materials is the P2841S-2N-F57 WXP40 insert suitable for? Material suitability must be checked in the Walter product matrix; the P2841S-2N-F57 WXP40 is an uncoated cemented-carbide grade and requires selection against the specific workpiece material. What is the purpose of the 2N-F57 chipbreaker? The 2N-F57 chipbreaker is designed to produce controlled, short chips under appropriate cutting parameters, improving chip evacuation and process reliability for drilling and boring. Is this insert coated? The P2841S-2N-F57 WXP40 is supplied as uncoated cemented carbide, which offers consistent edge behaviour and simplifies reconditioning. How should the insert be selected for drilling versus boring operations? Selection depends on hole depth, feed and finish requirements; use the grade WXP40 and chipbreaker data to match the intended operation and consult the supplier’s matrix for holder and parameter recommendations. Can the P2841S-2N-F57 WXP40 be used in automated production cells? Yes — the insert’s geometry and grade aim to deliver predictable performance suitable for automated drilling and boring sequences, provided cutting data and clamping arrangements are correctly set. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen. Markennamen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P2841S-3N-A57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WKP25S grade to achieve extended tool life and stable chip formation in demanding drilling and boring operations; order the insert via Metav Werkzeuge or contact our consultants for tailored application advice. P2841S-3N-A57 WKP25S Drilling/Boring indexable insert by Walter Tools — Tiger‑tec Silver, for steel & cast iron The P2841S-3N-A57 WKP25S is a drilling/boring indexable insert engineered for production environments that require consistent cutting results when machining steel and cast iron. Tiger‑tec Silver coated carbide grade WKP25S Optimised for steel and cast iron machining Stable chip formation and long tool life High process reliability for production use Increase uptime with a wear-resistant Tiger‑tec Silver grade The combination of the Tiger‑tec Silver coating and the WKP25S cemented carbide formulation is designed to extend tool life and reduce tool-change frequency. Coated carbide provides a hard, wear-resistant surface that delays flank and crater wear during continuous drilling and boring cycles, which translates into fewer interruptions and higher overall equipment effectiveness. For production lines where reliability and repeatability matter, this grade offers a measurable advantage in tool longevity and consistent cutting performance. Achieve reliable chip control and improved surface results The integrated 3N‑A57 chipbreaker geometry is tuned for the specific chip forms encountered when machining steel (P) and cast iron (K) according to ISO grouping. Stable chip formation reduces the risk of built-up edge and improves evacuation from the cutting zone, which in turn supports a better surface finish and lower rework rates. For less experienced users, the ISO letters P and K indicate suitability for unalloyed/alloyed steels and cast irons respectively, making material selection straightforward and reducing setup uncertainty. Seamless integration for production-grade drilling and boring This indexable insert follows common mounting and designation standards, so it is simple to insert into existing drilling and boring toolholders without extensive adaptation. The standardised designation helps maintenance and purchasing teams to reorder the correct item quickly and avoid downtimes. The combination of a process-oriented grade and a proven chipbreaker geometry promotes process security in high-volume machining and supports predictable cycle times for batch production. The insert is particularly useful where repeatable tolerance and surface quality matter across long runs. For improved process stability choose Walter Tools Tiger‑tec Silver inserts from Metav Werkzeuge — technical consultancy and fast delivery are available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: P2841S-3N-A57-WKP25S-WALTER Designation: P2841S-3N-A57 WKP25S Type: Drilling/boring indexable insert Manufacturer: Walter Tools Material group: P / K Core data Chipbreaker: 3N-A57 Grade: WKP25S Series: Tiger‑tec Silver SKU: P2841S-3N-A57-WKP25S-WALTER Special features Coating technology: Tiger‑tec Silver Suitable materials: Steel (P), Cast iron (K) Application: Drilling and boring operations Indexable insert geometry optimised for chip control FAQ What materials is this insert suitable for? The insert is specified for steel (ISO group P) and cast iron (ISO group K); the WKP25S grade and the 3N‑A57 chipbreaker ensure effective performance on these materials. How does the Tiger‑tec Silver coating benefit production? The Tiger‑tec Silver coating on the WKP25S grade increases wear resistance and helps maintain a stable cutting edge, which reduces tool changes and supports uninterrupted production. Can the insert be used with standard drilling holders? Yes. The designation aligns with common indexable insert standards and enables straightforward integration into compatible drilling and boring toolholders. What advantage does the 3N‑A57 chipbreaker provide? The 3N‑A57 chipbreaker produces controlled, short chips when machining cast iron and manageable chip forms in steels, improving evacuation and reducing the chance of chip-related interruptions. Is this insert suitable for high-volume production? Designed for production use, the combination of WKP25S grade and Tiger‑tec Silver coating offers process reliability and consistent performance for extended runs. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metal machining and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is original and factory-new.
P2841S-3N-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating performance, the WKP35S carbide grade and the 3N‑A57 chipbreaker for reliable machining of steel and cast iron; order genuine Walter Tools inserts from Metav Werkzeuge or consult our specialists for geometry and process matching. P2841S-3N-A57 WKP35S drilling/boring indexable insert — Walter Tools, Tiger·tec Silver, for steel and cast iron The P2841S-3N-A57 WKP35S drilling/boring indexable insert is a coated cemented carbide grade from the Tiger·tec Silver series, designed for productive machining of steel and cast iron with a dedicated 3N‑A57 chipbreaker. Tiger·tec Silver coated carbide grade Optimised for steel and cast iron machining Stable chip formation and abrasive wear resistance Consistent tool life and process reliability High-performance coating that reduces wear and keeps cycles running The Tiger·tec Silver coating combined with the WKP35S grade provides a balance between abrasion resistance and toughness, which is essential for continuous drilling and boring cycles. The layered coating reduces flank and crater wear under typical steel and cast‑iron cutting temperatures, leading to extended intervals between index changes. This technical advantage translates directly into fewer interruptions on the shop floor and more predictable tool life, supporting tighter production planning and lower per‑hole costs. Optimised geometry for controlled chip formation in P and K materials With the 3N‑A57 chipbreaker geometry, the insert delivers consistent chip control when machining both unalloyed and alloyed steel (P) and abrasive cast iron (K). The chipbreaker is engineered to produce short, manageable chips on interrupted or continuous cuts, reducing the risk of chip entanglement and improving surface integrity. For engineers assessing tooling options, the combination of chip control and coated carbide ensures process stability across typical ISO 513 workpiece classes. Productivity gains through repeatable performance and fewer tool changes The coated cemented carbide construction of this insert emphasises repeatable performance: predictable wear patterns allow for reliable change intervals and less unplanned downtime. In production environments where cycle time and first‑pass accuracy matter, the insert’s wear resistance contributes to consistent hole quality and reduced rework. When paired with suitable toolholders and correct cutting parameters, the result is higher throughput with maintained surface finish standards. Practical guidance for selection and integration in machining setups Selection of the P2841S‑3N‑A57 geometry should follow the workpiece material and cutting data: choose the WKP35S grade for mixed production of steel and cast iron where process reliability and tool life are priorities. The insert is intended for standard drilling and boring applications; matching insert seat and clamping system is essential to exploit the coating and chipbreaker benefits. For assistance with cutting speeds, feeds and holder compatibility, consult Metav Werkzeuge’s technical advisory to ensure optimal setup. Contact Metav Werkzeuge for tailored advice on Walter Tools Tiger·tec Silver WKP35S inserts, application recommendations and fast supply of genuine parts Technical data Article number: P2841S-3N-A57-WKP35S-WALTER Designation: P2841S-3N-A57 WKP35S Product type: drilling/boring indexable insert Manufacturer: Walter Tools Facts Series: Tiger·tec Silver Grade: WKP35S Chipbreaker: 3N‑A57 Applicable ISO groups: P, K Special features Coated cemented carbide Optimised for steel and cast iron machining Stable chip formation and abrasive wear resistance FAQ Which materials is this insert suitable for? The P2841S-3N-A57 WKP35S insert is suitable for steel (ISO group P) and cast iron (ISO group K) applications, as specified for the Tiger·tec Silver WKP35S grade. What does the 3N‑A57 chipbreaker provide? The 3N‑A57 chipbreaker offers controlled, short chip formation for drilling and boring in P and K materials, improving chip evacuation and surface quality during continuous and interrupted cuts. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating increases abrasion resistance and reduces flank and crater wear, leading to more consistent tool life and fewer unscheduled index changes when machining steel and cast iron. Is this insert compatible with standard drilling/boring toolholders? The P2841S‑3N‑A57 insert is designed for use in compatible drilling and boring systems; selection of the correct seat and clamping hardware is recommended to realise the described performance. Can this insert be used for both alloyed and unalloyed steels? Yes, the WKP35S grade within the Tiger·tec Silver series is formulated for a broad range of steels, encompassing unalloyed and alloyed types within the ISO P classification. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P2841S-3N-A57 WSP45G WSP45G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Gold coating and the WSP45G grade for extended edge life and reliable chip control; designed for drilling and boring in Stahl, rostfreier Stahl and high‑temperature alloys. Order the insert directly via Metav Werkzeuge or consult our technical team for application advice. P2841S-3N-A57 WSP45G drilling/boring indexable insert by Walter Tools — Tiger‑tec Gold for Stahl, rostfreier Stahl and superalloys A precision indexable insert, the P2841S-3N-A57 WSP45G is engineered for drilling and boring operations where stable chip formation and long tool life are required. Tiger‑tec Gold PVD coating WSP45G grade for versatile machining Chip control via 3N‑A57 breaker Suitable for Stahl, rostfreier Stahl and superalloys High process stability and predictable edge life The combination of the Tiger‑tec Gold coating and the WSP45G substrate offers a balance of wear resistance and toughness that reduces flank wear and prolongs service intervals. This grade is formulated for the demands of drilling and boring, where thermal loads and variable chip formation can shorten tool life. By choosing this insert, production setups gain greater process reliability, fewer tool changes and fewer interruptions to batch runs, resulting in measurable improvements in uptime and component throughput. Versatile material compatibility for mixed production runs Designed for the ISO groups P, M and S, the insert supports machining of Stahl, rostfreier Stahl and nickel‑based or titanium superalloys. The WSP45G cutting material is tuned to manage the heat generation and adhesive tendencies common when machining these groups, while the chipformer geometry contributes to controlled swarf evacuation. For workshops handling mixed lots, this flexibility reduces the need for multiple specialised tool inventories and simplifies tool management. Efficient chip control and secure cutting edge The 3N‑A57 chipbreaker geometry provides consistent chip segmentation under varying feeds and depths of cut, reducing the risk of built‑up edge and chip entanglement during drilling and boring. Stable chip formation protects the cutting edge from irregular loading and supports reliable regrinding intervals. Where component surface quality and dimensional repeatability matter, the insert’s geometry helps maintain finish and tolerance adherence without frequent parameter tweaks. Practical benefits for workshop integration The insert is compatible with standard drilling and boring holders designed for indexable carbide inserts and fits into existing tool systems with minimal adaptation. Its Tiger‑tec Gold coating supports higher cutting speeds where the machine and workholding permit, enabling shorter cycle times and improved productivity. For customers uncertain about holder compatibility or optimal cutting data, Metav Werkzeuge’s technical consultants can advise on suitable holders and process windows; this practical support complements the insert’s industrial performance. Contact Metav Werkzeuge today for application guidance or to check availability of the P2841S-3N-A57 WSP45G insert from Walter Tools — call +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data SKU: P2841S-3N-A57-WSP45G-WALTER Product: Bohr-/Aufbohrwendeschneidplatte (drilling/boring indexable insert) Designation: P2841S-3N-A57 WSP45G Grade: WSP45G Series: Tiger‑tec Gold Facts Material groups: P / M / S Chipbreaker: 3N‑A57 Applicable for: Stahl, rostfreier Stahl, superalloys Special features Coating: Tiger‑tec Gold (PVD) Material of insert: coated carbide Typical application: drilling and boring operations Manufacturer: Walter Tools; Tiger‑tec Gold technology FAQ What materials can be machined with this insert? The P2841S-3N-A57 WSP45G insert is suitable for machining Stahl, rostfreier Stahl and heat‑resistant superalloys, reflecting its design for ISO groups P, M and S. How does the Tiger‑tec Gold coating benefit drilling operations? The Tiger‑tec Gold PVD coating enhances wear resistance and thermal stability, which helps the insert maintain cutting performance under the cyclic heating typical of drilling and boring. Which chipbreaker is fitted and what advantage does it provide? This insert uses the 3N‑A57 chipbreaker, which promotes repeatable chip segmentation and secure evacuation, improving surface finish and reducing the risk of built‑up edge during penetration operations. Is this insert compatible with existing indexable drill systems? The insert is designed for standard drilling and boring toolholders that accept the specified insert geometry; consult Metav Werkzeuge for holder compatibility and recommended clamping practices. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Walter AG (brand: Walter Tools) with headquarters in Tübingen is part of the Sandvik group. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P2841S-3N-A57 WXP40 WXP40 Wendeplatten - Walter Tools
Take advantage of precise chip control and the reliability of an uncoated carbide cutting grade to maintain consistent drilling and boring cycles; order directly via Metav Werkzeuge or consult our specialists for application matching and stocking advice. P2841S-3N-A57 WXP40 – Drilling and boring indexable insert with 3N‑A57 chipbreaker, Walter Tools The P2841S-3N-A57 WXP40 is an indexable insert designed for drilling and boring operations, combining an uncoated carbide cutting grade with a dedicated chipbreaker to support stable machining across varied workpiece types; suitability must be checked against the product matrix. Uncoated carbide grade WXP40 Chipbreaker 3N-A57 for controlled chips Walter open series for versatile use Designed for drilling and boring inserts Improved process stability through controlled chip formation The insert’s primary benefit is consistent chip control, delivered by the 3N‑A57 chipbreaker, which stabilises the cutting zone and reduces the risk of irregular chip formation. In practice, this means fewer interruptions for chip clearing and more predictable tool behaviour during through‑hole drilling and boring cycles. The engineering behind the chipbreaker is optimised to produce short, manageable chips in a range of conditions, so that the machining process can be operated with a focus on cycle time and repeatability rather than constant manual intervention. Practical advantages of the open Walter cutting grade The WXP40 cutting grade is an uncoated carbide formulation from Walter Tools’ open series and is intended as a versatile general‑purpose grade. This composition provides a balance between toughness and wear resistance, supporting reliable performance in many standard machining scenarios. Because the grade is uncoated, it can be preferable where coating adhesion or specific surface chemistry is undesirable; however, the exact material compatibility should be verified in the product matrix to ensure optimal outcomes for each workpiece material. Integration in production and handling benefits Identification and replenishment are simplified by the standardised designation and the clear chipbreaker marking. The insert is produced for straightforward mounting in compatible drilling and boring tool bodies and can be stocked as part of a modular tool set. Traceability and part replacement are made easier by the established product code, which helps maintain orderly inventory management and predictable reordering within production planning. The overall effect is an insert that supports efficient workflows and reduces non‑productive time. For precise application advice and to ensure the WXP40 grade matches the intended workpiece, contact Metav Werkzeuge for specification support and ordering guidance via info@metav-werkzeuge.com or phone +49 2822 7131930. Technical data Article number: P2841S-3N-A57-WXP40-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P2841S-3N-A57 WXP40 Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte (drilling/boring indexable insert) Manufacturer: Walter Tools Grade: WXP40 Chipbreaker: 3N-A57 Series: Walter cutting grade - open series Material information: Katalogabhängig SKU / UID: P2841S-3N-A57-WXP40-WALTER Facts No numerical specifications provided in the source data Special features Uncoated carbide cutting grade (WXP40) Chipbreaker design 3N‑A57 for controlled chips Intended for drilling and boring applications Walter open cutting grade series Product matrix recommended for material suitability FAQ What materials is this insert suitable for? Material suitability must be checked in the product matrix; the P2841S-3N-A57 WXP40 is an uncoated carbide grade intended as a versatile option, but final selection depends on the specific workpiece material. Is the cutting grade coated? No, the WXP40 grade is supplied as an uncoated carbide and is specified as such for applications where an uncoated substrate is required. What advantage does the 3N‑A57 chipbreaker provide? The 3N‑A57 chipbreaker promotes controlled chip formation, improving process stability and reducing interruptions during drilling and boring operations. How is the insert identified for reordering? The insert is listed as P2841S-3N-A57 WXP40 (Walter Tools); use this exact designation or the SKU when reordering to ensure the same grade and chipbreaker are supplied. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanation. There is no connection between our company and the named brands. The offered item is original, factory‑new goods from the manufacturer Walter Tools.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com