P4841C-2R-F57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSP45G grade to increase edge life and machining stability; the insert’s chipbreaker geometry further improves chip control for drilling and reaming operations. Order or request application advice via Metav Werkzeuge for seamless integration into existing tool systems. P4841C-2R-F57 WSP45G drill/reamer indexable insert – Tiger·tec Gold, Walter Tools The P4841C-2R-F57 WSP45G is a coated carbide indexable insert designed for precision drilling and reaming in demanding metalworking applications, providing improved edge stability and consistent chip formation. Tiger·tec Gold coated carbide grade WSP45G Stable cutting edge for demanding materials Suitable for steel, stainless and superalloys For drilling and reaming operations Longer tool life through advanced coating technology The Tiger·tec Gold series combines a hard, wear-resistant PVD coating with a tough substrate to deliver extended tool life under cyclic thermal and mechanical loads. The WSP45G grade is a coated carbide designed to resist flank and crater wear while maintaining a stable cutting edge, which reduces the need for frequent index changes. For production environments this translates into fewer interruptions, improved overall productivity and more predictable tool consumption. Reliable performance across steel, stainless steel and superalloys Designed for the material groups P/M/S, the insert supports machining of plain and alloyed steel, stainless steel and superalloys (heat‑resistant materials and titanium). Each group presents different challenges — from heat generation and adhesive wear in steels to tough, work‑hardening behaviour in stainless steels and poor thermal conductivity in superalloys. The WSP45G grade balances toughness and hardness to maintain edge integrity and avoid built‑up edge, delivering consistent component quality in mixed‑material production. Controlled chips and safer holes with 2R‑F57 geometry The integrated chipbreaker geometry 2R‑F57 is engineered to fragment and evacuate chips reliably during drilling and reaming cycles. Optimised chip control reduces the risk of jamming and thermal loading at the cutting zone, which helps preserve hole accuracy and surface finish. For customers with limited chip evacuation space or automated setups, this geometry supports steady cycle times and lowers the risk of secondary operations caused by poor chip management. Practical integration for reliable machining processes As an indexable insert for drilling and reaming, the component fits into standard Walter tool bodies and clamping systems, enabling fast replacement and consistent pocket seating. The standardised indexable format reduces set‑up time and simplifies tool inventory management. In series production, the combination of a predictable wear pattern and straightforward reconditioning or disposal leads to lower overhead for tooling logistics and repeatable part quality. For tailored advice on integrating Walter Tools Tiger·tec Gold inserts into specific drilling or reaming applications, contact Metav Werkzeuge to discuss compatible tool bodies and process parameters: Metav Werkzeuge, info@metav-werkzeuge.com, +49 2822 7131930 Technical Data SKU: P4841C-2R-F57-WSP45G-WALTER Item: Bohr-/Aufbohrwendeschneidplatte P4841C-2R-F57 WSP45G Manufacturer: Walter Tools Facts Material groups: P / M / S Grade: WSP45G Chipbreaker: 2R-F57 Special features Series: Tiger·tec Gold Coating: PVD coated carbide Application: drilling and reaming Suitable for: steel; stainless steel; superalloys FAQ What materials is this insert suited for? The P4841C‑2R‑F57 WSP45G insert from Walter Tools is designed for machining steel, stainless steel and superalloys, corresponding to the P/M/S material groups. What does the WSP45G grade mean? WSP45G is a Walter Tools coated carbide grade within the Tiger·tec Gold family, offering a balance of wear resistance and toughness for milling, drilling and reaming applications. How does the 2R‑F57 chipbreaker help drilling operations? The 2R‑F57 chipbreaker promotes controlled chip formation and evacuation during drilling and reaming, reducing jamming risk and supporting consistent hole quality. Is the insert suitable for automated machining cells? Yes — the insert’s coating and chip control features are beneficial in automated production, where stable cutting behaviour and predictable tool change intervals are essential. Can this insert be used in standard Walter tool bodies? The insert is an indexable type intended for drill and reamer holders compatible with Walter Tools inserts; verify pocket and clamping compatibility with the specific tool body. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarks and trade names mentioned are the property of their respective owners and are used here for explanation only. There is no affiliation between Metav Werkzeuge and the named manufacturers. The offered item is an original, factory‑new product of the manufacturer.
P4841C-2R-F57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of uncoated carbide WXP40 and the 2R‑F57 chipbreaker for consistent chip formation and reliable drilling/boring performance; order directly via Metav Werkzeuge or contact their consultants for application-specific advice. P4841C-2R-F57 WXP40 — Drill/boring indexable insert with 2R‑F57 chipbreaker by Walter Tools A P4841C-2R-F57 WXP40 is a drill/boring indexable insert designed to deliver predictable cutting behaviour and stable chip evacuation in conventional drilling and bore-enlargement operations Uncoated carbide WXP40 grade 2R‑F57 chipbreaker geometry Designed for drill and boring operations Walter Tools quality and consistency Greater process stability through controlled chip formation The insert’s uncoated carbide construction and the 2R‑F57 chipbreaker combine to promote consistent chip control, which reduces cutting interruptions and tool-related downtime. In automated and manual drilling cycles alike, predictable chip shape lowers the risk of jamming and facilitates continuous operation, supporting higher effective productivity. As the WXP40 grade is an uncoated hardmetal, verify the specific workpiece suitability with the product matrix supplied by Walter Tools to ensure optimal cutting parameters and coolant strategies. Reliable results for drilling and bore-enlarging applications Designed for use in drilling and bore-enlargement contexts, the geometry of this indexable insert supports reproducible surface finish and dimensional stability during machining. The constructive features aim to reduce edge chipping and improve repeatability between index changes, which benefits batch production and maintenance of tolerances. Integration into existing toolholders is straightforward, enabling shorter set-up times and smoother process flows while maintaining process security and acceptable surface quality across standard metalworking tasks. Clear selection and inventory advantages for production planning Belonging to the Walter Schneidstoffsorte - Serie offen, the insert’s labelling and series coding simplify stock management and grade assignment in toolrooms. The designation indicates an open series where the WXP40 hardmetal class is provided as uncoated, so selection should be guided by the application matrix and machining strategy. This clarity supports procurement decisions, reduces overengineering of tool solutions and helps planners align tooling choices with machining cycles for economical and technically sound results. Contact Metav Werkzeuge GmbH for detailed application advice on Walter Tools inserts such as the P4841C-2R-F57 WXP40: email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and next steps Technical data Article number: P4841C-2R-F57-WXP40-WALTER Designation: P4841C-2R-F57 WXP40 Product type: Drill/boring indexable insert Manufacturer: Walter Tools Grade: WXP40 Chipbreaker: 2R‑F57 Series: Walter Schneidstoffsorte - Serie offen Material note: Katalogabhängig UID: P4841C-2R-F57-WXP40-WALTER Facts SKU: P4841C-2R-F57-WXP40-WALTER UID: P4841C-2R-F57-WXP40-WALTER Special features Uncoated hardmetal (carbide) grade Chipbreaker geometry for stable evacuation Series coding for straightforward inventory Suitable for drill and boring operations (confirm via product matrix) FAQ What materials is this insert suitable for? The suitability of the P4841C-2R-F57 WXP40 depends on the specific application matrix; the WXP40 class is an uncoated carbide grade so material compatibility should be checked against the Walter Tools product matrix before use. Is the insert coated or uncoated? This indexable insert is supplied as uncoated carbide in the WXP40 grade, offering predictable cutting behaviour where a coating is not specified. What does the 2R‑F57 designation mean? The 2R‑F57 denotes the chipbreaker geometry and specific insert form; this geometry is optimised for controlled chip formation in drilling and bore-enlargement operations. How to identify the correct insert for a drilling system? Match the insert designation and WXP40 grade to the toolholder and the Walter Tools product matrix to confirm fit and recommended cutting data for drilling and boring systems. Manufacturer: Walter AG (brand: Walter Tools); Headquarters: Tübingen, Germany. The Walter AG (brand: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names remain the property of their respective owners. The referenced brand names are used solely for explanation; there is no affiliation between Metav Werkzeuge and the mentioned manufacturers. The item offered is original, factory-new merchandise of the manufacturer.
P4841C-3R-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of a high-performance indexable solution that pairs the Tiger·tec Silver coating with the WKP35S grade for consistent edge life and dependable chip control in steel and cast iron machining; order genuine Walter Tools inserts via Metav Werkzeuge or consult our specialists for application advice. P4841C-3R-A57 WKP35S — Drilling and bore‑enlarging indexable insert (Walter Tools) A P4841C-3R-A57 WKP35S indexable insert engineered for productive drilling and bore‑enlarging operations in steel and cast iron, combining a specialised chipbreaker with a high‑performance coating for stable cutting conditions Tiger·tec Silver coating for extended tool life WKP35S grade for steel and cast iron machining Precision chipbreaker 3R‑A57 for consistent chips Designed for drilling and bore‑enlarging operations Consistent productivity through engineered chip control The combination of the 3R‑A57 chipbreaker and the Tiger·tec Silver technology delivers predictable chip formation during drilling and bore enlargement, reducing interruptions for chip evacuation and rework. This geometry is tailored to convert otherwise irregular swarf into controllable chips, which lowers cycle-time variability and supports a steady production flow. The result is fewer tool changes and more uptime on the machine. Extended edge life and thermal resistance for reliable shifts A coated carbide grade such as WKP35S offers increased wear resistance under the elevated temperatures typical of steel machining. The Tiger·tec Silver coating enhances hardness and adhesion, slowing abrasive and adhesive wear mechanisms. For workshop planning, this translates into longer tool life, more consistent component tolerances over a tool run and less frequent re‑grinding or replacement, supporting predictable process costs and reduced downtime. Broad material capability for flexible shop use The insert is specified for ISO groups P (steel) and K (cast iron), meaning the grade and geometry have been selected to handle both the heat‑affected cutting behaviour of steels and the abrasive, often breaking chips of cast iron. For operators unfamiliar with ISO groups: P denotes steels (unalloyed and alloyed) and K denotes cast iron; the insert’s specification confirms suitability across both families without needing separate tool inventories. Simple integration and measurable process benefits The indexable design facilitates economical tool management: individual inserts such as this reduce the expense of complete tool replacement and make inventory control more straightforward. The clear part‑geometry designation and branded grade enable reproducible results when paired with matching holders and the correct cutting data. Proven stability in cutting performance supports improved surface quality and keeps rework rates low, contributing directly to shop productivity and confidence in process planning. Contact Metav Werkzeuge to discuss holder compatibility, cutting parameters and to secure genuine Walter Tools inserts for demanding drilling and bore‑enlarging applications — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: P4841C-3R-A57-WKP35S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P4841C-3R-A57 WKP35S Walter Tools Type: Drilling and bore‑enlarging indexable insert Series: Tiger·tec Silver Grade: WKP35S Chipbreaker: 3R‑A57 Material suitability: P / K Manufacturer: Walter Tools Facts SKU / UID: P4841C-3R-A57-WKP35S-WALTER Special features Coated carbide grade (WKP35S) Tiger·tec Silver coating technology Optimised for steel (P) and cast iron (K) Chipbreaker geometry for stable swarf control Purpose: drilling and bore‑enlarging applications Brand: Walter Tools FAQ Which workpiece materials are suitable with this insert? The P4841C-3R-A57 WKP35S insert is specified for ISO groups P and K, making it suitable for machining steel and cast iron in drilling and bore‑enlarging tasks. What does the Tiger·tec Silver designation mean for performance? Tiger·tec Silver denotes a high‑performance coating system that improves hardness and wear resistance; for the WKP35S grade this yields longer edge life and greater thermal resilience during continuous drilling cycles. How does the 3R‑A57 chipbreaker help in production? The 3R‑A57 chipbreaker is engineered to produce controllable chips during drilling and boring, reducing chip jams and promoting consistent machining performance with the Walter Tools insert. Is this insert suitable for high‑speed cutting? While the datasheet specifies material groups and coating technology, cutting speed suitability depends on the specific machine, holder and process parameters; the WKP35S grade with Tiger·tec Silver is optimised for robust performance in typical steel and cast iron operations. Can tool life be predicted with this grade? The combination of WKP35S and the coating offers enhanced wear resistance, which supports predictable tool life under comparable cutting conditions; final tool life will vary with application, cutting data and machine setup. What applications is the insert primarily intended for? The insert is designed for productive drilling and bore‑enlarging operations where consistent chip control and wear resistance are required, particularly in workshops that machine steels and cast iron. Are these genuine Walter Tools inserts? This item is supplied as original factory‑new Walter Tools product; Metav Werkzeuge can confirm authenticity and provide advice on correct use. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
P4841C-3R-A57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold PVD performance, a stable cutting edge and versatile material compatibility for consistent machining results; order via Metav Werkzeuge or consult the team for application advice. P4841C-3R-A57 WSP45G drill/boring indexable insert – Tiger·tec Gold, 3R-A57 chipbreaker (Walter Tools) P4841C-3R-A57 WSP45G is a coated indexable insert engineered for demanding rotary cutting tasks, offering a balance of edge stability and versatile application across common workshop materials. Tiger·tec Gold PVD-coated grade WSP45G Suitable for Stahl, rostfreier Stahl and superalloys 3R-A57 chipbreaker for reliable chip control Robust grade for productive milling and boring Consistent performance through advanced coating technology The Tiger·tec Gold coating in this grade provides a wear-resistant surface that maintains a stable cutting edge under cyclic thermal and mechanical loads. The PVD coating method deposits a thin, adherent layer that improves resistance to abrasive wear and heat, translating into longer in-service intervals and predictable tool life. For production environments where repeatability matters, the coated carbide substrate supports steady dimensional results and reduces unscheduled tool changes, improving overall line efficiency. Improved process security with optimised chip control The integrated 3R-A57 chipbreaker is designed to shape and evacuate chips consistently across turning, milling and boring-related operations. Controlled chip formation reduces the risk of edge build-up and clogging in bores and tool holders, which contributes to fewer interruptions and safer machining cycles. In practice, the correct chip management accelerates cycle times and lowers the likelihood of surface defects, delivering measurable productivity gains on the shop floor. Versatility for a wide range of materials and operations This grade targets the material groups P / M / S — in other words Stahl, rostfreier Stahl and heat-resistant superalloys — offering a compromise of toughness and wear resistance that suits both roughing and finishing steps. The insert geometry supports stable cutting in interrupted cuts and demanding feeds common in milling and reaming operations. For users who require a single insert family across multiple components, this combination reduces inventory complexity while maintaining surface quality and dimensional control. Practical fitment and application advice for workshops Marked as P4841C-3R-A57 WSP45G, the insert integrates into standard indexable toolholders and is aimed at production-centric environments where process reliability is valued. Its robust grade mitigates edge chipping during moderate interruptions and its coating supports higher cutting parameters where thermal load is significant. For specific machine-tool combinations, Metav Werkzeuge can advise on optimal cutting data and holder selection to make the most of the insert’s benefits. Contact Metav Werkzeuge for tailored machining recommendations and availability of Walter Tools inserts to match production requirements Technical Data Article number: P4841C-3R-A57-WSP45G-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P4841C-3R-A57 WSP45G Walter Tools Product type: drill/boring indexable insert Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WSP45G Chipbreaker: 3R-A57 Applicable material groups: P / M / S ISO designation: P4841C-3R-A57 WSP45G UID: P4841C-3R-A57-WSP45G-WALTER Core specifications Coating: Tiger·tec Gold Substrate: coated carbide (PVD) Material applicability: Stahl, rostfreier Stahl, superalloys/titanium Designation: P4841C-3R-A57 WSP45G SKU: P4841C-3R-A57-WSP45G-WALTER Special features PVD-coated grade optimised for milling applications Tough, versatile grade for mixed production 3R-A57 chipformer for secure chip formation Stable cutting edge for repeatable surface quality Suitable for a range of rotary cutting tasks FAQ What materials is this insert suitable for? The P4841C-3R-A57 WSP45G grade is specified for groups P, M and S — that is Stahl, rostfreier Stahl and heat‑resistant superalloys, making it suitable across many common machining tasks. How does the Tiger·tec Gold coating benefit tool life? The Tiger·tec Gold PVD coating enhances wear resistance and thermal stability; for the P4841C-3R-A57 WSP45G insert this results in extended edge life and more consistent machining performance. What advantage does the 3R-A57 chipbreaker provide? The 3R-A57 chipformer produces controlled chips and improves evacuation during rotary cutting, which reduces build-up and lowers the risk of interruptions in boring and milling operations. Is this insert compatible with standard toolholders? The insert follows the P4841C-3R-A57 designation and fits corresponding indexable toolholders designed for this geometry; Metav Werkzeuge can confirm compatibility with specific holders. Can this grade be used for finishing as well as roughing? Yes — the balance of toughness and wear resistance in WSP45G suits both roughing and finishing steps, offering stable edges and good surface quality under varied cutting conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision cutting tools. Protected trademarks and trade names belong to their respective owners. Mention of brand names is for explanatory purposes only and does not imply any affiliation; the offered item is an original, factory‑new product of the manufacturer.
P4841C-3R-A57 WXP40 Wendeplatten - Walter Tools
Benefit from the combination of the WXP40 uncoated carbide grade, the 3R-A57 chipbreaker geometry and the standard designation P4841C-3R-A57 for consistent drilling and boring performance; order via Metav Werkzeuge or contact the consultants for application advice. P4841C-3R-A57 WXP40 — Drill/Boring indexable insert by Walter Tools The P4841C-3R-A57 WXP40 is an indexable insert developed for drilling and boring tasks, offering uncoated cemented carbide substrate and a purpose-designed chipbreaker for controlled chip formation in matched workpiece materials. Uncoated carbide grade WXP40 3R-A57 chipbreaker geometry For drilling and boring applications Walter Tools designation P4841C-3R-A57 Engineered for consistent performance in drilling and boring The insert combines an uncoated cemented carbide grade with a defined chipbreaker to support predictable cutting behaviour under the correct process conditions. When integrated into a compatible holder and machining cycle, the design aims to promote stable metal removal and repeatable results. The substrate is classified as WXP40, an uncoated grade; suitability for particular workpiece materials should be verified against the manufacturer’s product matrix to ensure the correct match for hardness and alloy. Chip control that supports process reliability The 3R-A57 chipbreaker is intended to influence chip formation during drilling and boring operations, reducing the risk of long, stringy chips and helping maintain a consistent evacuation path. Proper chip control can reduce interruptions, improve surface finish and aid tool-change planning. In practical terms, this means the insert is best selected where controlled chips contribute to uninterrupted productivity and where the machining strategy benefits from a defined chip shape. Practical guidance for selection and inventory The product is identified by the designation P4841C-3R-A57 WXP40, which simplifies procurement and replacement in production environments. Material information is catalogue-dependent; therefore, confirm the recommended workpiece materials and cutting data in the manufacturer matrix before application. Keeping the insert designation and chipbreaker specification in standard stock helps reduce downtime and ensures compatibility with Walter Tools tool systems. Contact Metav Werkzeuge for tailored machining recommendations for the Walter Tools P4841C-3R-A57 WXP40 insert — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data SKU: P4841C-3R-A57-WXP40-WALTER Article name: Drill/Boring indexable insert P4841C-3R-A57 WXP40 Manufacturer: Walter Tools Designation: P4841C-3R-A57 WXP40 Core specifications Chipbreaker: 3R-A57 Grade: WXP40 (uncoated cemented carbide) Series: Walter cutting-grade series — open series Material information: catalogue-dependent Special features Indexable insert for drilling and boring Uncoated cemented carbide grade Check product matrix for material suitability Walter designation P4841C-3R-A57 FAQ What materials is this insert suitable for? The WXP40 grade is an uncoated cemented carbide, and suitability for specific materials must be checked in the Walter Tools product matrix; the insert is intended for drilling and boring where the matrix indicates compatibility. What is the function of the 3R-A57 chipbreaker? The 3R-A57 geometry is a chipbreaker designed to shape and control chips during drilling/boring operations, aiding evacuation and supporting a steady cutting process when used with the correct cutting data. Can this insert be used for hardened steels? Hardened or pre-hardened steel suitability is not specified in the provided data; please consult the Walter Tools product matrix to confirm whether the P4841C-3R-A57 WXP40 insert is recommended for particular hardness ranges. How should the insert be ordered? Order using the designation P4841C-3R-A57 WXP40 or the SKU P4841C-3R-A57-WXP40-WALTER and specify the required chipbreaker and holder interface to ensure correct compatibility. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and brand names mentioned are the property of their respective owners and are cited for explanation only. There is no connection between our company and the brands named. The offered item is an original, factory-new product of the manufacturer Walter Tools.
P4841C-3R-E57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Silver coating and the WKP35S grade for high productivity in drilling and boring of steel and cast iron; the 3R‑E57 chipbreaker promotes secure chip control and extended tool life. Order directly via Metav Werkzeuge or consult their specialists for cutting data and process optimisation. P4841C-3R-E57 WKP35S — Drilling/Boring indexable insert for steel and cast iron — Walter Tools The P4841C-3R-E57 WKP35S is a coated carbide indexable insert optimised for productive drilling and boring operations in a wide range of steels and cast irons Tiger·tec Silver coating for longer tool life WKP35S grade for steel and cast iron 3R‑E57 chipbreaker for stable chip control Suitable for productive drilling and boring Faster cycle times through targeted material design The Tiger·tec Silver coating, combined with the WKP35S coated carbide grade, is designed to reduce wear and maintain a stable cutting edge during continuous drilling operations. This results in fewer index changes and longer intervals between tool interventions, which directly improves productivity on medium- to high-volume machining tasks. The coating technology also aids thermal resistance, so the insert keeps its geometry better at elevated cutting temperatures. Reliable chip control and process security The 3R‑E57 chipbreaker geometry delivers consistent chip control for the characteristic chip forms encountered when machining steel and cast iron. Stable chip evacuation reduces risk of re-cutting and protects the hole surface finish, supporting repeatable results in series production. The chip management also contributes to safer setups by preventing chip accumulation in the tool path, which is especially beneficial during deep-hole drilling and when using higher feeds. Practical advantages for workshop planning Using this insert in a standard drilling or boring tool body permits predictable tool-life assessments thanks to the combination of coating and substrate. The coated carbide substrate provides a balance between toughness and wear resistance, enabling economical operation across diverse component batches. For planners, this means simplified inventory management: one grade covers multiple steel and cast-iron applications without frequent tool changes. How the insert improves component quality Through its geometry and coating, the insert supports improved dimensional consistency and surface integrity of machined holes. Better heat control and reduced abrasive wear help to avoid premature tool edge breakdown, which in turn preserves bore tolerance and reduces scrap rates. The overall effect is a measurable improvement in process capability for medium-duty drilling and boring tasks. Contact Metav Werkzeuge today for tailored cutting data and application advice for the P4841C-3R-E57 WKP35S insert and to discuss suitable tool bodies and speeds Technical data Article number: P4841C-3R-E57-WKP35S-WALTER Designation: P4841C-3R-E57 WKP35S Product type: Drilling/boring indexable insert Manufacturer: Walter Tools Facts Grade: WKP35S Geometry / chipbreaker: 3R‑E57 Series: Tiger·tec Silver Material group: P / K Special features Coating technology: Tiger·tec Silver Substrate: coated carbide (cemented carbide) Suitable for: Steel, Cast iron Typical application: Productive drilling and boring FAQ Which materials are best suited for this insert? The P4841C-3R-E57 WKP35S insert from Walter Tools is intended for machining steel and cast iron, matching the P and K ISO material groups. What is the main benefit of the Tiger·tec Silver series? Tiger·tec Silver provides improved wear resistance and thermal stability, so the insert maintains cutting performance longer under typical drilling loads. How does the 3R‑E57 chipbreaker affect machining? The 3R‑E57 chipbreaker offers controlled chip formation and evacuation, which supports consistent surface finish and reduces the likelihood of chip-related interruptions. Is this insert suitable for interrupted cuts or heavy roughing? The coated carbide construction and the WKP35S grade balance toughness and wear resistance; the insert is capable in many roughing scenarios, while very heavy interruptions may require alternative grades. Can the same insert be used across different steel alloys? Yes, the WKP35S grade is designed for a broad range of steels, providing stable performance across typical alloy variations encountered in production environments. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P4841C-3R-E57 WSP45G WSP45G Wendeplatten - Walter Tools
High durability and consistent chip control from the Tiger‑tec Gold coating and the 3R‑E57 chipbreaker support uninterrupted machining of steels and heat‑resistant alloys; combined with the versatile WSP45G grade, this insert reduces rework and increases tool life. Order the Bohr-/Aufbohrwendeschneidplatte P4841C-3R-E57 WSP45G directly via Metav Werkzeuge or ask our consultants if needed. P4841C-3R-E57 WSP45G drilling/reaming indexable insert – Tiger‑tec Gold, 3R‑E57 (Walter Tools) P4841C-3R-E57 WSP45G is a drilling and reaming indexable insert designed for demanding holemaking operations in steel, stainless steel and heat‑resistant superalloys, offering stable chip formation and enhanced tool life. Tiger‑tec Gold PVD for extended tool life WSP45G grade for steel, stainless and superalloys 3R‑E57 chipbreaker for stable chip control Maximise productivity with controlled chip formation The 3R‑E57 chipbreaker is engineered to produce consistent, segmented chips in through‑hole and interrupted cutting conditions, reducing the risk of built‑up edge and machine downtime. Stable chip evacuation directly lowers the frequency of tool changes and part clearing, which translates into measurable productivity gains on high‑volume runs. In practical terms, operators benefit from fewer interruptions and more predictable cycle times, while process engineers gain a repeatable machining parameter window for reliable output. Consistent performance across demanding materials Built on the Tiger‑tec Gold platform and specified as WSP45G, the insert is a PVD‑coated carbide grade optimised for the thermal and mechanical demands of group P (steel), M (stainless steel) and S (superalloys/titanium) materials. The coating improves heat resistance and wear behaviour, while the substrate provides fracture toughness for intermittent cutting. For customers without specialist tooling knowledge: PVD stands for physical vapour deposition, a thin, hard coating that protects the carbide and preserves the cutting edge under elevated temperatures typical of stainless and heat‑resistant alloys. Longer tool life and consistent surface quality The combination of coating technology and chip control delivers lower flank and crater wear rates, which helps maintain surface finish and dimensional stability for serial holemaking. For operations such as drilling followed by light reaming or boring passes, the insert supports repeatable hole geometry and reduces scrap rates. This reliable performance not only saves on tooling expenditure over time but also supports higher first‑pass yield and less manual rework, an economic benefit for production lines aiming for consistent quality. Practical application and technical support Specifically designed for drilling and reaming tasks, the insert integrates into standard indexable toolholders suitable for Walter Tools systems and similar interfaces. Where cutting speeds, feeds or coolant strategies require fine tuning, technical guidance is recommended to achieve optimal results with WSP45G inserts. If additional process data or cutting parameter advice is required, Metav Werkzeuge provides application support and can advise on adapting the insert to specific machine and material combinations — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations. Contact Metav Werkzeuge for application advice and to request Walter Tools P4841C‑3R‑E57 WSP45G inserts for your next holemaking project Technical Data Article number: P4841C-3R-E57-WSP45G-WALTER Designation: P4841C-3R-E57 WSP45G Brand: Walter Tools Data Material groups: P / M / S Series: Tiger‑tec Gold Grade: WSP45G Special features Chipbreaker: 3R‑E57 Coating: Tiger‑tec Gold (PVD) Substrate: coated carbide Application: drilling and reaming indexable insert Compatibility: designed for steel, stainless steel and heat‑resistant alloys FAQ What materials is the insert suitable for? The P4841C‑3R‑E57 WSP45G insert is suitable for steel, stainless steel and heat‑resistant superalloys, reflecting its P/M/S material group rating and the Tiger‑tec Gold coating. How does the 3R‑E57 chipbreaker improve machining? The 3R‑E57 chipbreaker on this insert controls chip shape and evacuation, reducing built‑up edge and promoting stable cutting forces for improved process reliability. Can the insert be used for interrupted cuts? Yes, the grade and coated carbide substrate provide toughness for intermittent cutting; however, specific machine and holder setup should be checked for optimal results with P4841C‑3R‑E57 inserts. Is technical support available for application parameters? Metav Werkzeuge offers application support and can provide cutting data and recommendations for the Walter Tools insert to suit machine, material and coolant conditions. Does the Tiger‑tec Gold coating affect tool life in high‑temperature alloys? The Tiger‑tec Gold PVD coating enhances heat resistance and wear protection, contributing to longer tool life and more consistent surface quality when machining demanding alloys. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original, brand‑new product of the manufacturer Walter Tools.
P4841C-3R-E57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of WXP40 uncoated carbide and the 3R-E57 chipbreaker geometry for consistent chip control and reliable tool life; order the insert directly via Metav Werkzeuge or consult the technical team for matching toolholder data. P4841C-3R-E57 WXP40 – Drill/boring indexable insert, 3R-E57 chipbreaker (Walter Tools) A P4841C-3R-E57 WXP40 insert engineered for drilling and boring applications, combining an uncoated carbide grade with a dedicated 3R-E57 chipbreaker to support stable metal removal in production environments WXP40 uncoated carbide grade 3R-E57 chipbreaker geometry P4841C-3R-E57 insert format Walter Tools production standard Consistent chip control for efficient metal removal The 3R-E57 chipbreaker is designed to influence chip formation at the cutting edge, reducing snarling and improving evacuation in interrupted cuts. As an uncoated carbide grade, WXP40 provides predictable wear behaviour and straightforward regrindability. The combination of chip geometry and substrate aims to increase effective machining time by producing short, controllable chips, which simplifies coolant flow and swarf handling. For specific workpiece materials and cutting data, the product matrix should be consulted to confirm the best parameter window. Stable cutting edge and repeatable process performance A focus on edge stability supports process stability during serial production. The insert format and cutting geometry contribute to consistent surface quality and dimensional repeatability when integrated into a suitable toolholder. The indexable design reduces downtime associated with regrinding and tool changes, while the uncoated carbide substrate offers a balance between toughness and hardness for variable cutting conditions. For optimisation, toolmakers commonly validate insert performance per component programme and machine setup. Straightforward integration into existing tooling systems The designation P4841C-3R-E57 indicates a standardised insert format that simplifies replacement and inventory management across compatible drilling and boring tool assemblies. Correct clamping and seat fit are essential for achieving the expected performance; adapters and toolholders must match the insert geometry. For selection and compatibility, check holder specifications and the Walter Tools product documentation or the technical matrix to confirm seat angle and clamping requirements before assembly. Contact Metav Werkzeuge for detailed specification checks and to request assistance matching the P4841C-3R-E57 WXP40 insert to the correct toolholder and application Technical data SKU: P4841C-3R-E57-WXP40-WALTER Designation: Bohr-/Aufbohrwendeschneidplatte P4841C-3R-E57 WXP40 Walter Tools Manufacturer: Walter Tools Insert designation: P4841C-3R-E57 WXP40 Facts UID: P4841C-3R-E57-WXP40-WALTER Article code: P4841C-3R-E57 WXP40 Special features Grade: WXP40 (uncoated carbide) Chipbreaker: 3R-E57 Series: Walter Schneidstoffsorte - Serie offen Material information: Katalogabhängig Product type: Bohr-/Aufbohrwendeschneidplatte Format: P4841C-3R-E57 FAQ Which materials is this insert suitable for? Suitability depends on the Walter product matrix; the P4841C-3R-E57 WXP40 is an uncoated carbide grade and workpiece recommendations should be checked in the technical matrix before application. How does the 3R-E57 chipbreaker benefit drilling operations? The 3R-E57 chipbreaker promotes controlled chip segmentation and evacuation, reducing the risk of chip jamming and supporting a more stable cutting process with the P4841C-3R-E57 insert. Is regrinding possible for this insert? As an uncoated carbide grade, WXP40 typically allows for controlled regrinding within the limits specified by Walter Tools; follow the manufacturer’s guidelines for reclaiming cutting edges. What must be checked before installing the insert in a toolholder? Confirm seat geometry, clamping compatibility and the toolholder’s rated application; the insert format P4841C-3R-E57 must match the holder specifications to ensure secure seating and the expected cutting performance. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and product names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanation and comparison; there is no affiliation between our company and the trademark owners. The offered item is an original, brand-new product from the manufacturer.
P4841C-3R-F57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver wear resistance and the 3R‑F57 chipbreaker for reliable machining of steel and cast iron; the result is efficient, reproducible metal removal with long tool life. Order the insert directly via Metav Werkzeuge or consult the team for application advice. P4841C-3R-F57 WKP35S drilling/boring indexable insert – Tiger‑tec Silver, WKP35S, Walter Tools P4841C-3R-F57 WKP35S is a drilling and boring indexable cutting insert designed for precision material removal in steel and cast iron applications Tiger‑tec Silver coating for high wear resistance Optimised for steel (P) and cast iron (K) 3R‑F57 chipbreaker for controlled chips Compatible with P4841C‑geometry insert holders Maximise throughput with advanced coating technology The Tiger‑tec Silver series offers a modern, coated carbide grade that is engineered for extended performance in demanding turning and boring tasks. The WKP35S grade provides a balance between wear resistance and toughness, which reduces flank wear and maintains cutting-edge stability under elevated temperatures. For industrial users processing ISO groups P (steel) and K (cast iron), this means fewer tool changes and more predictable batch runtimes. The insert’s coating and substrate combination is particularly effective where thermal loads and abrasive wear coexist, enabling longer intervals between regrinds or replacements and improving overall process economics. Steady chip control for uninterrupted production The 3R‑F57 chipbreaker geometry promotes consistent chip formation, minimising entanglement and helping to evacuate swarf reliably during through‑hole and boring operations. Controlled chips reduce the risk of surface damage and machine stoppages, contributing directly to uptime. In practice, stable chip behaviour simplifies coolant strategies and lowers the risk of tool breakage in interrupted cuts. The indexable format facilitates quick replacement without the need to re‑qualify toolholders, which supports a lean production flow and decreases fixture downtime in high‑mix manufacturing environments. Proven suitability and easy integration into workflows Designed for standard P4841C insert holders and compatible tool systems, this indexable cutting solution integrates with existing holders and toolpaths with no redesign required. The grade WKP35S is a coated carbide type tailored to the thermal and mechanical characteristics of steel and cast iron, as defined in ISO 513 material groups. For applications requiring repeatable hole quality and consistent diameters in serial production, the insert’s geometry and grade deliver reproducible results, reducing in‑process variability. If further technical data or cutting parameter examples are required for specific alloys or cycle times, Metav Werkzeuge’s consultants are available to advise on feeds, speeds and holder selection. For high‑performance drilling and boring with Walter Tools’ Tiger‑tec Silver inserts, contact Metav Werkzeuge for stock details and application recommendations at info@metav-werkzeuge.com or +49 2822 7131930 — expert advice for reliable machining. Technical Data Article number: P4841C-3R-F57-WKP35S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P4841C-3R-F57 WKP35S Walter Tools SKU: P4841C-3R-F57-WKP35S-WALTER Facts Series: Tiger‑tec Silver Grade: WKP35S Chipbreaker: 3R‑F57 Special features Product type: drilling/boring indexable insert Material compatibility: P (steel), K (cast iron) Coating technology: Tiger‑tec Silver Substrate: coated carbide FAQ What materials is this insert designed for? The insert is designed for ISO material groups P (steel) and K (cast iron); the WKP35S grade and Tiger‑tec Silver coating are optimised for these applications. How does the 3R‑F57 chipbreaker affect machining? The 3R‑F57 chipbreaker promotes controlled chip formation and reliable evacuation, which reduces the risk of swarf interference and improves surface quality during drilling and boring. Is the insert compatible with standard P4841C holders? Yes, the geometry corresponds to P4841C insert holders, allowing straightforward integration into existing tool setups. Can this insert be used for interrupted cuts or heavy roughing? The coated carbide grade provides a balance of toughness and wear resistance suited to many roughing tasks; selection for heavily interrupted cutting should consider cutting parameters and holder rigidity. Where can one obtain cutting data for specific steel grades? Metav Werkzeuge can supply recommended feeds and speeds for common steel and cast iron grades; contact their technical team for tailored parameters. What are the main benefits of the Tiger‑tec Silver series? Tiger‑tec Silver combines modern coating technology with a robust substrate to extend tool life, improve wear resistance and support consistent machining results across production runs. Is the product supplied as original factory material? The article is an original, factory‑new product from the manufacturer and delivered as new. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
P4841C-3R-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Taking advantage of the combination of Tiger‑tec Gold PVD technology, a controlled 3R‑F57 chipbreaker and a versatile WSP45G grade provides a reliable indexable insert suited to demanding drilling and bore‑enlarging tasks; order the P4841C‑3R‑F57 WSP45G directly via Metav Werkzeuge or contact the consultants for application advice. P4841C-3R-F57 WSP45G Drilling / Boring Indexable Insert by Walter Tools — Tiger‑tec Gold PVD The P4841C‑3R‑F57 WSP45G is an indexable insert engineered for drilling and bore‑enlarging operations, offering wear resistance and edge stability for applications in steel, stainless steel and heat‑resistant alloys. Tiger‑tec Gold PVD coating for enhanced wear resistance WSP45G PVD‑coated cemented carbide grade Suitable for steel, stainless steel and superalloys 3R‑F57 chipbreaker for controlled chip formation Boosted tool life through advanced coating and grade The combination of the Tiger‑tec Gold coating and the WSP45G grade yields a balanced performance profile that extends tool life under mixed cutting conditions. The PVD‑coated cemented carbide substrate provides increased resistance to abrasive wear and thermal degradation, which translates into longer intervals between indexable insert changes and fewer unplanned tool swaps. For machining shops aiming to raise overall process efficiency, this technical pairing contributes directly to reduced downtime and more predictable cycle times. Reliable chip control and consistent cut quality The integrated 3R‑F57 chipbreaker is designed to promote stable chip formation during drilling and bore‑enlarging operations, reducing the risk of built‑up edge and improving surface finish. Controlled chip evacuation decreases the incidence of recutting and supports consistent dimensional accuracy. As a result, operations that require tight tolerances benefit from fewer rework cycles and a steadier production flow, making the insert a good choice for medium‑ to high‑volume drilling tasks where repeatability is essential. Versatility across challenging materials and tougher environments Engineered for use in material groups P, M and S, the insert performs well in unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys or titanium workpieces. The grade’s toughness helps absorb intermittent shocks and maintain a sharp cutting edge when heat conduction is poor, while the coating reduces friction and improves wear resistance at elevated temperatures. The result is a versatile solution for workshops that machine a range of steels and high‑temperature alloys without frequent tool changes. Contact Metav Werkzeuge today to discuss how the Walter Tools Tiger‑tec Gold P4841C-3R-F57 WSP45G insert can improve drilling reliability and throughput for specific applications Technical data Article number: P4841C-3R-F57-WSP45G-WALTER Designation: P4841C-3R-F57 WSP45G Type: Drilling/Boring indexable insert Grade: WSP45G Material groups: P / M / S Manufacturer: Walter Tools Facts Chipbreaker: 3R‑F57 Series: Tiger‑tec Gold Coating: PVD SKU: P4841C-3R-F57-WSP45G-WALTER Special features Suitable for steel (P), stainless steel (M), superalloys/titanium (S) Controlled chip formation Enhanced wear resistance and edge stability Application: drilling and bore‑enlarging operations FAQ What materials can be machined with this insert? The P4841C‑3R‑F57 WSP45G is suitable for steel, stainless steel and heat‑resistant superalloys/titanium, covering the ISO groups P, M and S. How does the 3R‑F57 chipbreaker affect machining? The 3R‑F57 chipbreaker on the P4841C‑3R‑F57 promotes controlled chip formation and evacuation, improving surface finish and reducing recuts during drilling and bore‑enlarging tasks. Is the WSP45G grade suitable for high‑temperature alloys? Yes, the WSP45G grade, with its Tiger‑tec Gold PVD treatment, is designed to withstand the thermal and mechanical stresses encountered when machining heat‑resistant alloys. Can this insert be used in automated production environments? The P4841C‑3R‑F57 WSP45G’s consistent wear behaviour and chip control characteristics make it a reliable choice for automated drilling and boring processes where predictability is required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world's leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned exclusively for explanation; there is no affiliation between our company and the mentioned brands. The offered item is original and brand new.
P4841C-3R-F57 WXP40 Wendeplatten - Walter Tools
Take advantage of the uncoated carbide WXP40 grade and the 3R‑F57 chipbreaker to achieve stable chip formation and consistent drilling performance; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific advice. P4841C-3R-F57 WXP40 drill/bore-enlargement indexable insert by Walter Tools — 3R‑F57 chipbreaker P4841C-3R-F57 WXP40 is an indexable insert engineered for drilling and bore-enlargement applications, combining an uncoated carbide grade with a dedicated 3R‑F57 chipbreaker to support reliable metal removal in industrial machining. Uncoated carbide grade WXP40 3R‑F57 chipbreaker geometry Designed for drilling and bore enlarging Consistent cutting performance for demanding machining The P4841C-3R-F57 WXP40 insert is built from uncoated carbide and sized for drilling and bore-enlargement tasks where predictable tool behaviour is essential. The WXP40 grade provides a balance between toughness and wear resistance, which helps maintain dimensional stability across runs. For production environments seeking reduced scrap rates and steady cycle times, the insert’s material and geometry enable sustained process stability and repeatable hole quality. Compatibility with standard indexable holders ensures straightforward integration into existing tool setups. Controlled chip formation and predictable tool life Equipped with a purpose-designed chipbreaker, the 3R‑F57 geometry promotes short, segmented chips that evacuate reliably from the hole, lowering the risk of re-cutting and tool damage. This leads to improved surface finish and reduced machine downtime. Because the cutting material is uncoated carbide, the insert tolerates variable cutting parameters and can be reground or inspected without coating-related restrictions. The direct consequence is enhanced productivity through fewer interruptions and a consistent rate of material removal, particularly in series production or batch machining workflows. Practical application guidance and material suitability The insert is delivered as part of Walter’s open series and is identified by the ISO designation P4841C-3R-F57 WXP40; suitability for specific workpiece materials should be checked against the manufacturer’s product matrix. Where the workpiece mix or hardness varies, matching cutting data and clamping arrangements to the insert geometry preserves accuracy and extends service intervals. For complex jobs or mixed-material batches, Metav Werkzeuge offers application support and can assist in selecting holder geometry and cutting parameters to make the most of the insert’s precision features. Discuss machining requirements with Metav Werkzeuge to confirm the P4841C-3R-F57 WXP40 insert as the right choice for improved hole quality and process reliability Technical data Article number: P4841C-3R-F57-WXP40-WALTER SKU: P4841C-3R-F57-WXP40-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte Facts No numerical specifications provided in the source data No cutting diameter or thickness values supplied Special features Grade: WXP40 (uncoated carbide) Chipbreaker: 3R‑F57 Series: Walter Schneidstoffsorte - Serie offen ISO designation: P4841C-3R-F57 WXP40 Note: Verify workpiece suitability with the product matrix FAQ What materials is this insert suitable for? The P4841C-3R-F57 WXP40 insert uses an uncoated carbide grade; actual suitability for specific materials must be checked against the Walter Tools product matrix and application tables. How does the 3R‑F57 chipbreaker affect machining? The 3R‑F57 chipbreaker promotes short, controllable chips during drilling and bore enlargement, improving chip evacuation and protecting the cutting edge for steadier performance. Can the insert be reground or recoated? As an uncoated carbide insert, the P4841C-3R-F57 WXP40 can be inspected for regrinding where applicable; any reconditioning should follow Walter Tools’ recommendations to maintain geometry and tolerances. Manufacturer/Responsible: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and product names are the property of their respective owners. Brand names and registered marks are used for explanation only. There is no affiliation or partnership between Metav Werkzeuge and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
P4841C-4R-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, a dedicated WKP35S carbide grade and a 4R‑A57 chipbreaker to maintain steady productivity and predictable tool life; order through Metav Werkzeuge or contact our consultants for machining guidance. P4841C-4R-A57 WKP35S – Drill/Boring indexable insert, Tiger‑tec Silver, for steel & cast iron (Walter Tools) P4841C-4R-A57 WKP35S is a drill/boring indexable insert engineered for high‑productivity operations on steel and cast iron, offering a coated‑carbide grade and a defined chipbreaker for stable machining results. Tiger‑tec Silver coating for extended tool life Optimised for steel (P) and cast iron (K) 4R‑A57 chipbreaker for consistent chip control Coated carbide grade WKP35S for productive machining Increased uptime through advanced coating and grade selection The combination of Tiger‑tec Silver technology and the WKP35S grade results in a coated carbide construction that resists abrasive and adhesive wear, which extends the effective service life of the insert. Coatings reduce friction and thermal load at the cutting edge, so cutting parameters can be exploited more consistently; this means fewer interruptions for index changes and a more reliable production rhythm when machining steel and cast iron. For workshops seeking measurable gains in tool life and process stability, the engineering behind this insert translates directly into lower tooling consumption and predictable maintenance intervals. Predictable chips and better surface finish with the right geometry The 4R‑A57 chipbreaker is designed to produce short, controllable chips in the typical chip regimes of P and K materials, reducing the risk of stringing or clogging in through‑tool and non‑through operations. Effective chip control improves tool engagement, lowers the chance of edge build‑up and contributes to a superior surface finish without extensive secondary operations. For operators unfamiliar with chipbreaker terminology: the chipbreaker is a small geometry on the face of the insert that shapes and segments the metal swarf, converting what would otherwise be disruptive long chips into short, manageable fragments that evacuate reliably. Easy adoption in production workflows for measurable efficiency gains The insert designation P4841C‑4R‑A57 WKP35S reflects a geometry and chip control concept optimised for drilling and boring tasks where repeatability matters. As an indexable insert, it permits quick corner changes and consistent performance across insert life, supporting efficient set‑ups and reduced machine downtime. By selecting a grade tailored to steel and cast iron, the cutting process becomes more economical: higher material removal rates are achievable without compromising edge stability, and predictable wear behaviour simplifies process planning. For practical application, pairing this insert with proper feeds and speeds adapted to the workpiece class will yield the best balance between productivity and insert life. For tailored machining recommendations with Walter Tools' Tiger‑tec Silver inserts, contact Metav Werkzeuge for expert advice and technical data at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: P4841C-4R-A57-WKP35S-WALTER Designation: P4841C-4R-A57 WKP35S Product type: Drill/Boring indexable insert Manufacturer: Walter Tools Facts Chipbreaker: 4R‑A57 Grade/series: WKP35S / Tiger‑tec Silver Material groups: P / K Special features Coating: Tiger‑tec Silver Carbide type: Coated carbide Suitable for steel (P) Suitable for cast iron (K) Series: Tiger‑tec Silver FAQ What materials is this insert designed for? This insert is designed for machining steel and cast iron (material groups P and K); the WKP35S grade and Tiger‑tec Silver coating are matched to those workpiece families. How does the Tiger‑tec Silver coating improve performance? The Tiger‑tec Silver coating on the WKP35S grade reduces friction and thermal stress at the cutting edge, leading to better wear resistance and more consistent tool life during drilling and boring operations. What advantage does the 4R‑A57 chipbreaker provide? The 4R‑A57 chipbreaker produces short, controllable chips that evacuate reliably, improving process stability and contributing to a consistent surface finish with fewer interruptions. Can this insert be used for high‑productivity drilling? Yes, the combination of the WKP35S grade and the Tiger‑tec Silver coating supports productive machining strategies by enabling stable cutting conditions and longer intervals between index changes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P4841C-4R-A57 WSP45G WSP45G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold PVD coating and the WSP45G grade for extended edge life and reliable chip control when machining Steel, stainless steel and heat‑resistant alloys; order the insert via Metav Werkzeuge or consult our specialists for application advice. P4841C-4R-A57 WSP45G — Drill / Boring indexable insert by Walter Tools The P4841C-4R-A57 WSP45G is a precision indexable insert for drilling and bore enlargement, designed for demanding use in Steel, stainless steel and heat‑resistant alloys. Tiger·tec Gold PVD coating for heat resistance WSP45G grade for stable edge life Optimised chipformer for secure chip control Suitable for steel, stainless steel and superalloys Longer tool life through a heat‑resistant coating and robust grade The combination of the Tiger·tec Gold coating and the WSP45G grade provides a PVD‑coated carbide surface that resists thermal wear and reduces edge breakdown. This results in consistent tool life and fewer unscheduled tool changes, which supports steady machine uptime and improved cost efficiency. The coating technology is engineered to withstand the thermal loads typical for drilling and bore enlargement, so downtime is minimised and productivity is maintained over longer production runs. Reliable chip control and process security for operations Equipped with the 4R‑A57 chipformer, the insert ensures predictable chip formation and evacuation during through‑hole and enlargement cycles. Stable chip control reduces the risk of built‑up edge and associated surface defects, so component quality is improved without complex process adjustments. The geometry was developed to balance cutting forces and chip flow, meaning that the machining process is easier to monitor and control, delivering higher first‑pass yields. Versatility across challenging materials for flexible shop use Rated for the ISO groups P / M / S, the insert is suited to a wide material spectrum: unalloyed and alloyed steel, stainless steel, and heat‑resistant superalloys and titanium. The alloy‑adapted grade supports machining when heat generation and material toughness would typically shorten tool life. For shops facing mixed production lots, this versatility reduces tooling variants and simplifies inventory management while maintaining acceptable surface finish and dimensional stability. Practical advantages for integration and handling The design is focused on practical deployment in standard drilling and boring toolholders: the insert’s identification and grade code facilitate quick tool selection and repeatability in serial production. The robust edge behaviour and chipformer geometry support higher cutting parameters where appropriate, enabling faster cycle times without sacrificing reliability. Documentation and SKU referencing allow straightforward replacement and traceability in tool management systems. For drilling and boring tasks that demand process stability, specify the Walter Tools Tiger·tec Gold grade such as the P4841C-4R-A57 WSP45G and contact Metav Werkzeuge for tailored application recommendations and availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: P4841C-4R-A57-WSP45G-WALTER Designation: P4841C-4R-A57 WSP45G Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Facts Material groups: P / M / S Applicable to: Steel; stainless steel; heat‑resistant alloys / titanium SKU: P4841C-4R-A57-WSP45G-WALTER Special features Series: Tiger·tec Gold Grade: WSP45G (PVD‑coated carbide) Chipformer: 4R‑A57 Application: drilling and bore enlargement FAQ What materials is this insert suitable for? The P4841C-4R-A57 WSP45G insert is applicable to the ISO material groups P, M and S, meaning it is suitable for steel, stainless steel and heat‑resistant superalloys including titanium. How does the Tiger·tec Gold series improve performance? Tiger·tec Gold coating on the WSP45G grade increases thermal resistance and edge stability, so the Walter Tools insert achieves longer service life under typical drilling and boring thermal loads. What role does the 4R‑A57 chipformer play? The 4R‑A57 chipformer is designed to produce compact, controllable chips during drilling and enlargement, enhancing chip evacuation and reducing the risk of built‑up edge when using the WSP45G grade. Is this insert suitable for serial production environments? Yes, the P4841C-4R-A57 WSP45G is optimised for repeatable performance and longer tool life, making it well suited for continuous production where process stability is critical. How is the insert identified for reordering? Reordering can be done via the SKU P4841C-4R-A57-WSP45G-WALTER, which identifies the exact Walter Tools grade and geometry. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P4841C-4R-A57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of the WXP40 carbide grade and the 4R‑A57 chipbreaker to achieve consistent chip control and predictable tool life; order the P4841C‑4R‑A57 WXP40 drilling/reaming insert via Metav Werkzeuge or contact their advisors for application support. P4841C-4R-A57 WXP40 drilling/reaming indexable insert — 4R‑A57 chipbreaker by Walter Tools The P4841C-4R-A57 WXP40 is a drilling and reaming indexable insert designed for stable chip formation and broad material coverage in industrial metalcutting applications. Uncoated carbide grade WXP40 4R‑A57 chipbreaker geometry For drilling and reaming operations Delivering reliable productivity for drilling processes The insert combines an uncoated carbide grade with a defined chipbreaker geometry to ensure repeatable results in holemaking. The choice of WXP40 provides a balance between toughness and wear resistance, which supports steady cutting forces and reduces the risk of unexpected edge chipping. In practice, consistent chip formation reduces process interruptions and enables longer tool cycles, contributing directly to a more efficient production rhythm. Chip control and process stability explained The 4R‑A57 chipbreaker is engineered to break and evacuate chips effectively during drilling and reaming, lowering the likelihood of built-up edge and improving coolant access. For engineers unfamiliar with the term: a chipbreaker is a micro‑geometry on the cutting face that guides chips into smaller, controllable fragments. The result is a safer machining environment, improved surface finish of the hole, and fewer stoppages due to chip entanglement — benefits that become especially relevant in medium‑ to high‑volume production. Practical compatibility and application guidance This insert is supplied in the design designation P4841C‑4R‑A57 and is part of the Walter open series for cutting grades. The material specification is listed as catalogue‑dependent, so matching the insert to the specific workpiece material should be verified against the manufacturer’s product matrix. When integrated into suitable drill or reaming holders, the geometry supports both roughing and finishing passes, offering flexibility for mixed‑batch workshops and series production alike. Handling, tool life and economical machining Because the grade is uncoated carbide, the insert is straightforward to resharpen or replace within indexable systems, helping to keep tooling inventories manageable. The combination of the WXP40 carbide class and the chipbreaker reduces wear progression under stable cutting parameters, which translates into predictable tool life and lower total machining cost per hole. For operations seeking a pragmatic balance between performance and cost control, this insert provides a dependable option. For reliable, productive cutting with Walter Tools’ WXP40 grade and the 4R‑A57 chipbreaker, contact Metav Werkzeuge for tailored advice and prompt supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: P4841C-4R-A57-WXP40-WALTER Designation: P4841C-4R-A57 WXP40 Product type: drilling/reaming indexable insert Brand: Walter Tools Data No numerical specifications provided in the dataset Special features Grade: WXP40 (uncoated carbide) Chipbreaker: 4R‑A57 Series: Walter Schneidstoffsorte - Serie offen Material note: catalogue‑dependent ISO designation: P4841C-4R-A57 WXP40 Manufacturer SKU / UID: P4841C-4R-A57-WXP40-WALTER FAQ What types of operations is this insert intended for? The P4841C‑4R‑A57 WXP40 insert is intended for drilling and reaming operations where controlled chip formation and consistent hole quality are required. Which materials can be machined with this grade? The insert uses the WXP40 uncoated carbide grade; suitability for specific materials should be checked in Walter Tools’ product matrix as the dataset lists material information as catalogue‑dependent. How does the 4R‑A57 chipbreaker affect surface finish? The 4R‑A57 chipbreaker promotes smaller, controlled chips and improved evacuation, which commonly leads to a better surface finish in holemaking compared with undefined chip formation. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is original, factory‑new merchandise of the manufacturer.
P4841C-4R-E57 WKP35S Wendeplatten - Walter Tools
Combining the Tiger‑tec Silver coating and the WKP35S wear grade, this indexable insert delivers stable chip formation and extended tool life when machining steel and cast iron. Benefit from improved process reliability and reduced downtime; order the insert directly via Metav Werkzeuge or consult our specialists for geometry and application advice. P4841C-4R-E57 WKP35S indexable drill/reaming insert — Tiger‑tec Silver coating, for steel and cast iron | Walter Tools The P4841C-4R-E57 WKP35S is an indexable drill/reaming insert designed for high demands in drilling and bore-finishing operations on steel and cast iron. Tiger‑tec Silver coating for long tool life WKP35S: coated carbide for reliable wear resistance Optimised 4R‑E57 chipbreaker for consistent chips Suited for machining steel and cast iron Improved productivity through stable cutting performance The Tiger‑tec Silver series combines a modern coating system with a robust carbide substrate to increase tool life and maintain cutting-edge stability. The WKP35S grade is engineered for the thermal and abrasive conditions typical of machining steel and cast iron, which reduces flank wear and keeps bore tolerances stable over longer tool intervals. By choosing this insert, production planners can expect fewer tool changes and more predictable cycle times, supporting continuous throughput and lower per-part manufacturing cost. Predictable chip control and surface quality An optimised 4R‑E57 chipbreaker geometry provides reliable chip control in interrupted and continuous drilling. The chip form is directed away from the cutting zone, decreasing re-cutting and improving thermal conditions at the cutting edge. For operators less familiar with insert geometries: the chipbreaker shapes the chips to prevent long, entangling swarf and to reduce the risk of surface damage. This results in consistent bore finishes and simplifies downstream cleaning, delivering measurable quality improvements with minimal process adjustment. Application guidance and handling benefits The insert is supplied in a standard indexable format that eases replacement and ensures consistent seating in compatible drill bodies. The coated indexable insert offers high process security during serial production and is particularly suitable where repeatability matters. For shops that process mixed batches of unalloyed and alloyed steels or grey and ductile irons, the WKP35S grade provides the versatility to handle varying workpiece conditions without frequent grade swaps. Simple handling and predictable wear behaviour also support planning for tool inventory and regrinding cycles. Contact Metav Werkzeuge for tailored recommendations on using the Tiger‑tec Silver WKP35S inserts in specific drilling setups — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data SKU: P4841C-4R-E57-WKP35S-WALTER Article: Bohr-/Aufbohrwendeschneidplatte P4841C-4R-E57 WKP35S Manufacturer: Walter Tools Facts Designation: P4841C-4R-E57 WKP35S Chipbreaker: 4R-E57 Material groups: P / K UID: P4841C-4R-E57-WKP35S-WALTER Special features Series: Tiger‑tec Silver Grade: WKP35S (coated carbide) Suitable for: Steel (P) and cast iron (K) according to ISO groupings Product type: Indexable drill/reaming insert FAQ What materials is this insert optimised for? The insert is optimised for machining steel and cast iron (ISO groups P and K) thanks to the WKP35S coated carbide grade and the Tiger‑tec Silver technology. How does the 4R‑E57 chipbreaker improve machining? The 4R‑E57 chipbreaker shapes and breaks chips to reduce re-cutting and improve evacuation, which enhances surface finish and stabilises tool life during drilling and reaming. Is this insert suitable for high-speed conditions? The Tiger‑tec Silver coating and coated carbide substrate support elevated cutting performance; suitability for specific cutting speeds depends on machine capability and workpiece alloying—trial cuts are recommended to determine optimal parameters. Can the insert be used in indexable drill holders from other manufacturers? The insert follows standard indexable geometries; compatibility depends on the holder specification. Verify seat and clamp compatibility for the P4841C-4R-E57 geometry before use. How does the WKP35S grade compare to uncoated carbide? The WKP35S coated grade offers superior wear resistance and thermal stability compared with uncoated carbide, providing longer tool life and more consistent process results in mixed steel and cast-iron applications. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany; Walter Tools Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanation. There is no connection between our company and the named brands. The offered item is original, brand-new merchandise of the manufacturer.
P4841C-4R-E57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold PVD coating, a tough, versatile carbide grade, and an optimised chipbreaker to maintain steady machining performance across Stahl, rostfreier Stahl and high‑temperature alloys; order the P4841C‑4R‑E57 WSP45G directly via Metav Werkzeuge or ask our consultants if needed. P4841C-4R-E57 WSP45G drilling/boring indexable insert — PVD‑coated carbide for Stahl, rostfreier Stahl (Walter Tools) The P4841C‑4R‑E57 WSP45G is a drilling and boring indexable insert engineered for stable material removal in demanding components made from Stahl, rostfreier Stahl and heat‑resistant alloys, combining a Tiger‑tec Gold coating with a purpose‑built chipbreaker for reliable chip control. Tiger‑tec Gold PVD coating Suitable for Stahl and rostfreier Stahl Stable cutting edge for extended life Optimised chipbreaker 4R‑E57 Consistent productivity through coating and grade The core advantage of this insert lies in the Tiger‑tec Gold PVD coating and the WSP45G carbide grade. Together they deliver a balance of toughness and wear resistance that reduces unexpected tool changes and supports longer intervals between indexings. For production environments where throughput and predictability matter, the coated grade helps to maintain a steady cutting edge under the thermal and mechanical stresses typical when machining Stahl and rostfreier Stahl. This reduces downtime and contributes to a more consistent process window on drilling and boring operations. Better chip control and process stability Equipped with the 4R‑E57 chipbreaker, the insert improves chip formation during deep holes and bore enlargements, preventing long, entangling chips and promoting safer evacuation. The optimised geometry also supports stable cutting forces and reduces vibration, which aids in achieving repeatable bore quality and dimensional stability. For operators seeking predictable cycle times and fewer interrupted runs, the chip control and edge robustness translate directly into measurable process reliability. Application range and material compatibility explained The cutting grade is specified for P / M / S groups, meaning it is suited to a broad set of materials: unalloyed and alloyed Stahl, rostfreier Stahl and heat‑resistant superalloys or titanium. The material compatibility reflects a deliberate design for heat resistance and edge stability where thermal load and poor thermal conductivity challenge the insert performance. In practice, this makes the insert particularly useful where a single grade must cover mixed batches of Stahl and high‑temperature components without frequent grade changes. Practical benefits for workshop and production planning Adopting this indexable insert supports simpler tool management because one grade can address multiple workpiece materials, reducing inventory complexity. The coated carbide construction and robust chipbreaker help to minimise unscheduled interventions and support a smoother production flow. When paired with stable cutting parameters and appropriate clamping, the insert contributes to improved component finish and consistent hole geometry over longer tool life. Contact Metav Werkzeuge for application guidance on the Tiger‑tec Gold WSP45G grade and secure the P4841C‑4R‑E57 WSP45G for high‑performance drilling and boring in Stahl and rostfreier Stahl Technical data SKU: P4841C-4R-E57-WSP45G-WALTER Article name: drilling/boring indexable insert P4841C-4R-E57 WSP45G Product type: drilling/boring indexable insert Manufacturer: Walter Tools Core specifications Grade: WSP45G Coating technology: Tiger·tec Gold (PVD) Chipbreaker designation: 4R‑E57 Material groups: P / M / S Special features Coated carbide construction Optimised chip control geometry Designed for stability under thermal load Versatile use across Stahl, rostfreier Stahl and superalloys FAQ Which materials can be machined with this indexable insert? The insert is designed for machining Stahl, rostfreier Stahl and heat‑resistant superalloys/titanium, reflecting the P / M / S material groups specified for the WSP45G grade. What does the WSP45G designation indicate? WSP45G is Walter Tools’ coated carbide grade in the Tiger‑tec Gold family, chosen for toughness and versatility, particularly where a single grade must handle mixed machining tasks. How does the 4R‑E57 chipbreaker benefit drilling and boring operations? The 4R‑E57 chipbreaker is optimised to promote controlled chip formation and evacuation, reducing the risk of entangling chips and supporting stable cutting forces during bore enlargements. Is the P4841C‑4R‑E57 WSP45G suitable for high‑temperature alloy work? Yes — the P / M / S compatibility and the Tiger‑tec Gold coating provide enhanced edge stability and heat resistance, making the insert suitable for certain heat‑resistant alloys and titanium applications. How is tool life supported by the coating and geometry? The Tiger‑tec Gold PVD coating improves wear resistance while the insert geometry maintains a stable cutting edge; together they reduce flank wear and help extend index intervals for more consistent production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article is original, brand‑new merchandise of the manufacturer (Walter Tools).
P4841C-4R-E57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of precise chip control and a robust uncoated carbide grade for stable drilling and boring cycles; the integrated 4R‑E57 chipbreaker improves swarf evacuation and process reliability. Order the insert via Metav Werkzeuge or consult our specialists for application-specific selection. Bohr-/Aufbohrwendeschneidplatte P4841C-4R-E57 WXP40 — indexable insert for drilling and boring (Walter Tools) P4841C-4R-E57 WXP40 is an indexable insert engineered for drilling and boring operations, offering a balance of reliable chip formation and repeatable cutting performance for a wide range of production environments. Uncoated carbide grade WXP40 Chipbreaker 4R‑E57 for controlled chips Suitable for drilling and boring operations Walter Tools precision and consistency Delivering consistent chip control for reliable cycles The integrated 4R‑E57 chipbreaker is designed to produce predictable swarf shapes and direct chips away from the cutting zone, which reduces recutting and improves cycle stability. In practical terms, predictable chip formation lowers the risk of tool damage and shortens downtime for swarf clearing. The chipbreaker geometry is particularly beneficial in interrupted cuts and deeper bore operations, where effective chip evacuation directly supports higher process reliability and steady production rhythm. Robust substrate selection for repeatable edge life The insert is supplied in the uncoated WXP40 carbide grade, optimised for toughness and steady wear behaviour. An uncoated hardmetal substrate like this supports long-lasting cutting edges where thermal stability and mechanical resistance are required. For purchasers and toolroom planners, this means improved repeatability of results across batches and fewer unexpected tool changes. Note that actual workpiece compatibility should be verified against the product matrix to ensure the grade matches the intended material and cutting conditions. Practical integration into machining systems Designed as an indexable solution for both drilling and boring toolholders, the geometry enables straightforward mounting and replacement within standard cutter assemblies. The insert’s designation and geometry simplify inventory management and reordering, helping maintain a compact and consistent tooling set. When integrating the insert into a machining process, attention to clamping and toolholder condition will preserve the qualities of the cutting edge and support the expected surface finish and dimensional accuracy. Benefits for production-focused shops For production environments seeking steady output, the combination of a controlled chipbreaker and a tough uncoated grade contributes to predictable tool behaviour and fewer process interruptions. Shops that prioritise throughput and process stability will value the balance between chip control and edge robustness, which together help reduce scrap and improve overall machining efficiency. While the insert is versatile, final selection should consider the specific material and operational parameters documented in the product matrix. Contact Metav Werkzeuge today for tailored advice on integrating Walter Tools P4841C-4R-E57 WXP40 inserts into production processes and for current availability and ordering support Technical data Article number: P4841C-4R-E57-WXP40-WALTER Designation: P4841C-4R-E57 WXP40 Product type: Bohr-/Aufbohrwendeschneidplatte Brand: Walter Tools Facts SKU: P4841C-4R-E57-WXP40-WALTER UID: P4841C-4R-E57-WXP40-WALTER Material designation: Katalogabhängig Special features Uncoated carbide (WXP40) Chipbreaker: 4R‑E57 Series: Walter Schneidstoffsorte - Serie offen Application focus: drilling and boring indexable insert Sorteneignung: check product matrix for material suitability FAQ What materials is this insert intended for? The insert in the WXP40 grade is intended for a range of workpiece materials; material suitability should be verified against the product matrix for the P4841C-4R-E57 WXP40 insert to ensure optimal performance. Is the P4841C-4R-E57 supplied with a coating? The P4841C-4R-E57 WXP40 is supplied as an uncoated carbide insert, offering toughness and consistent wear behaviour without an additional coating layer. How does the 4R‑E57 chipbreaker affect drilling operations? The 4R‑E57 chipbreaker shapes and directs chips to improve evacuation from the bore, reducing recutting and supporting stable cutting conditions during drilling and boring cycles. Can this insert be used in both drilling and boring toolholders? Yes, the geometry and designation of the P4841C-4R-E57 WXP40 are intended for integration into compatible drilling and boring cutter assemblies, facilitating straightforward replacement and inventory control. What should be checked before selecting this insert for a new application? Confirm workpiece material compatibility using the supplied product matrix and ensure toolholder condition and clamping meet the required specifications for the P4841C-4R-E57 WXP40 to achieve the expected surface finish and tool life. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P4841C-4R-F57 WKP35S WKP35S Wendeplatten - Walter Tools
Take advantage of a high-performance, coated carbide grade that balances long tool life with consistent chip control for machining steel and cast iron; order or request technical advice via Metav Werkzeuge to ensure the insert meets specific process requirements. P4841C-4R-F57 WKP35S drilling/boring indexable insert — Tiger·tec Silver coating for steel and cast iron by Walter Tools P4841C-4R-F57 WKP35S is an indexable insert designed for drilling and bore-enlarging operations, optimised for reliable performance in steel and cast iron machining Tiger·tec Silver coated grade WKP35S Designed for steel and cast iron applications Chipbreaker 4R-F57 for stable chip control Walter Tools quality and repeatability Consistent performance in steel and cast iron machining The Tiger·tec Silver coating combined with the WKP35S cutting grade provides a balance of wear resistance and thermal stability that benefits continuous drilling and bore-enlarging tasks. As a coated carbide indexable insert, this geometry manages the heat and abrasive contact typical for group P (steel) and group K (cast iron) applications. The result is reliable flank wear progression and predictable service intervals, which supports stable cycle times and fewer unscheduled tool changes. The combination of coating and substrate ensures the insert maintains cutting edge integrity under typical production loads. Optimised chip control for safer, faster cycles Equipped with the chipbreaker 4R-F57, the insert promotes effective chip control across a range of cutting parameters, reducing the risk of long, tangled chips and helping to protect the workpiece surface. The specific chip geometry reduces cutting forces and vibration, which contributes to improved surface finish and dimensional stability in bore operations. For shops where repeatability and throughput matter, this geometry supports higher feed constancy and fewer interruptions for chip clearing, translating into measurable productivity gains. Coating and grade that extend tool life and reliability The combination of a coated carbide substrate and the Tiger·tec Silver technology increases resistance to adhesive and abrasive wear while preserving cutting-edge strength at elevated temperatures. This is particularly advantageous when machining abrasive cast irons or medium-alloy steels where thermal loads and intermittent contact can accelerate wear. The engineered coating also improves repeatability from one insert to the next, helping to standardise setup and inspection intervals and to simplify tooling inventory management. Practical application and handling recommendations The insert is intended for drilling and bore-enlarging work in a production environment where consistent performance is required. Use standard clamping torque and verified seat cleanliness to maintain positional accuracy; incorrect seating can compromise the insert life and surface quality. For cutting data, consult toolholder and machine guidelines and consider gradual increases in speed or feed when optimising cycle times. For specific parameter windows related to material grades and machine rigidity, Metav Werkzeuge can provide tailored recommendations to match the WKP35S grade to the application. Contact Metav Werkzeuge for tailored application advice and supply options for Walter Tools inserts to secure consistent machining results and process stability Technical Data Article number: P4841C-4R-F57-WKP35S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte P4841C-4R-F57 WKP35S Walter Tools Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte Series: Tiger-tec Silver Facts Grade: WKP35S Material group suitability: P / K Chipbreaker: 4R-F57 Special features Coating technology: Tiger·tec Silver Coated carbide cutting grade Application: steel and cast iron machining ISO designation: P4841C-4R-F57 WKP35S SKU: P4841C-4R-F57-WKP35S-WALTER UID: P4841C-4R-F57-WKP35S-WALTER FAQ What materials is this insert suited for? The insert is suitable for steel (ISO group P) and cast iron (ISO group K); the WKP35S grade is tuned for these material groups. How does the chipbreaker 4R-F57 affect machining? The chipbreaker 4R-F57 improves chip control and reduces vibration, supporting better surface finish and fewer interruptions during drilling or bore-enlarging operations. What benefits does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases wear resistance and thermal stability, which helps extend the tool life of the insert under continuous production loads. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory-new goods of the manufacturer (Walter Tools).
P4841C-4R-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, the versatile WSP45G grade and the stable 4R‑F57 chipbreaker to increase machining productivity while reducing tool inventory. Order the P4841C-4R-F57 WSP45G indexable insert directly via Metav Werkzeuge or consult the team for application support. P4841C-4R-F57 WSP45G — drill/reamer indexable insert by Walter Tools, Tiger‑tec Gold, 4R‑F57 The P4841C-4R-F57 WSP45G is an indexable insert for drilling and reaming applications, designed for productive metalcutting of Stahl, rostfreier Stahl and heat-resistant alloys, featuring a Tiger‑tec Gold PVD coating and a 4R‑F57 chipbreaker. Tiger‑tec Gold PVD coating Versatile for P, M, S materials Stable 4R‑F57 chipbreaker Consistent chip formation for reliable production The geometry with the 4R‑F57 chipbreaker ensures controlled chip formation during interrupted and continuous cuts, which reduces rework and machine downtime. The chip control is especially beneficial when machining tougher materials such as rostfreier Stahl and high-temperature alloys, where reliable evacuation prevents built-up edge and improves surface quality. As a result, cycle times remain stable and the entire process becomes more predictable, supporting higher throughput in serial production. Coating and grade designed for longer tool life The insert's Tiger‑tec Gold PVD system in the WSP45G grade provides a combination of toughness and wear resistance suited to demanding operations. The coated carbide substrate resists abrasive wear while the PVD layer improves thermal stability, allowing higher cutting parameters on many workpiece materials. This technical pairing translates into longer tool life and fewer indexings, which lowers tooling costs per component and supports continuous, productive machining. One insert for multiple materials — fewer tool changes With suitability for the ISO groups P, M and S, the insert covers a wide material range: Stahl, rostfreier Stahl and heat‑resistant superalloys and titanium. This versatility reduces the need for multiple specialised grades at the machine, simplifying inventory and setup. For shops facing varied batch work, the result is less spindle downtime for tool changes and fewer tool management overheads, while retaining the machining quality expected from premium inserts. Designed for secure seating and predictable performance The insert geometry and designation are optimised for standard drilling/reaming toolholders, providing a secure fit and repeatable orientation. That mechanical reliability supports dimensional stability during machining and eases handling in automated workflows. Combined with the insert’s material and coating properties, the result is a balance of process security and achievable surface finish without excessive compromise on cutting speeds. Contact Metav Werkzeuge for personalised application advice and to request the P4841C-4R-F57 WSP45G insert for high‑productivity drilling and reaming with Tiger‑tec Gold coating Technical Data Article number: P4841C-4R-F57-WSP45G-WALTER Article name: Bohr-/Aufbohrwendeschneidplatte P4841C-4R-F57 WSP45G Walter Tools Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WSP45G Chipbreaker: 4R‑F57 Material designation: P / M / S ISO designation: P4841C-4R-F57 WSP45G Product type: Bohr-/Aufbohrwendeschneidplatte UID: P4841C-4R-F57-WSP45G-WALTER Facts Number of cutting edges: 4R Geometry/angle: 57° Special features PVD coating: Tiger‑tec Gold Substrate: coated carbide Suitable for: Stahl, rostfreier Stahl, superalloys and titanium Application: drilling and reaming indexable insert Brand: Walter Tools FAQ What materials can this insert machine effectively? The P4841C-4R-F57 WSP45G insert is suitable for Stahl, rostfreier Stahl and high-temperature superalloys including titanium, reflecting its P/M/S suitability and the toughness of the WSP45G grade. What benefit does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold PVD coating on the WSP45G grade increases thermal stability and wear resistance, enabling higher cutting parameters and longer tool life in demanding drilling and reaming operations. How does the 4R‑F57 chipbreaker affect machining? The 4R‑F57 chipbreaker promotes controlled chip formation and evacuation, reducing the risk of built-up edge and improving surface finish and process stability during interrupted and continuous cuts. Is this insert compatible with standard drill/reamer holders? Yes; the P4841C-4R-F57 WSP45G is designed for secure seating in common indexable drill and reamer toolholders, offering repeatable orientation and reliable clamping for precision work. Which production environments benefit most from this insert? Workshops processing mixed batches of Stahl, rostfreier Stahl and heat‑resistant alloys will benefit from the insert’s versatility, as it reduces tool variants and supports stable, productive machining. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and brand names are the property of their respective owners. Brand names and registered trademarks are used for explanatory purposes only and indicate no affiliation. The offered item is an original, factory-new product of the manufacturer Walter Tools.
P4841C-4R-F57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of stable chip formation, uncoated carbide performance and a dedicated 4R‑F57 chipbreaker to secure predictable machining cycles and reduced rework. Order the insert directly via Metav Werkzeuge or consult the specialists for cutting-data support and process integration. P4841C-4R-F57 WXP40 – Drill/bore indexable insert, uncoated carbide with 4R‑F57 chipbreaker | Walter Tools The P4841C-4R-F57 WXP40 is a drill/bore indexable insert engineered for productive drilling and bore‑enlargement operations, offering stable chip control and broad applicability within general turning and drilling tool assemblies. Uncoated carbide grade WXP40 Integrated 4R‑F57 chipbreaker Stable chip formation for predictable cycles Open series for broad material range Maximise process reliability and cycle consistency The insert’s primary advantage is its contribution to process reliability. Manufactured in the WXP40 grade, an uncoated carbide designed for steady wear behaviour, the cutting edge is suited to repetitive drilling tasks where reliable lifetime and consistent results matter. Because the substrate is free of surface coatings, reconditioning and inspection processes are straightforward, which benefits shops that favour predictable tool-change intervals. This results in fewer unexpected interruptions and a more stable production flow. Predictable chip control reduces secondary operations The integrated 4R‑F57 chipbreaker is optimised to influence chip geometry and evacuation. In practice, the chipbreaker shapes fragments so that they break reliably under typical feed and speed windows, which reduces the risk of entanglement and limits workpiece marking. Where chip management is critical—for example in multi‑operation machining centres or when machining long bores—the controlled chip form lowers the likelihood of secondary cleaning and rework, thereby improving overall throughput and reducing cycle time variance. Versatile application: check suitability in the product matrix This insert belongs to an open series intended for a wide range of applications, but material suitability must be validated against the specific product matrix. The grade performs well in general machining scenarios and is aimed at users who require a pragmatic balance between economy and performance. For materials with particular hardness or alloy compositions, consult the technical matrix to confirm the best cutting parameters and to ensure optimal tool life and surface finish. Practical handling and integration benefits As an indexable insert, the design supports rapid replacement without complex regrinding, which keeps machine downtime minimal. The insert designation and ISO labelling facilitate inventory management and traceability in production planning. For procurement and integration, the SKU is referenced in technical documentation, allowing maintenance teams to order consistent replacements and to align tool data with CAM setups. Contact Metav Werkzeuge for application advice and procurement of Walter Tools inserts, quoting SKU P4841C-4R-F57-WXP40 to ensure rapid assistance and tailored cutting data. Technical Data Article number: P4841C-4R-F57-WXP40-WALTER Description: Bohr-/Aufbohrwendeschneidplatte P4841C-4R-F57 WXP40 Walter Tools Manufacturer: Walter Tools UID: P4841C-4R-F57-WXP40-WALTER Key figures Grade: WXP40 Chipbreaker: 4R‑F57 Series: Walter Schneidstoffsorte - Serie offen Insert designation: P4841C-4R-F57 WXP40 Materials & features Material: Catalogue-dependent Substrate class: uncoated carbide Application note: Verify workpiece suitability in product matrix Product type: Drill/bore indexable insert FAQ What materials is this insert intended for? The P4841C-4R-F57 WXP40 insert is supplied in an uncoated carbide grade; suitability for specific workpiece materials should be checked in the product matrix and cutting‑data tables provided by Walter Tools. How does the 4R‑F57 chipbreaker affect machining? The 4R‑F57 chipbreaker on the P4841C-4R-F57 WXP40 controls chip form to promote reliable breaking and evacuation, which helps to reduce entanglement and minimise secondary cleaning operations. Can this insert be reconditioned or reground? As an uncoated carbide indexable insert, the P4841C-4R-F57 WXP40 is designed for economical replacement; reconditioning options depend on shop capability and are generally less common than replacement for this insert class. Which toolholders are compatible with this insert designation? Compatibility is determined by the holder design and clamping geometry; use the ISO designation P4841C-4R-F57 WXP40 to match the insert with the appropriate Walter Tools or third‑party toolholder. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand‑new goods from the manufacturer. The Walter AG (brand appearance: Walter Tools) is part of the global tool industry and is recognised for precision tooling and process solutions.
P4841C-5R-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Silver coating and the WKP35S grade for consistent tool life and reliable chip control in demanding drilling and boring operations; consult Metav Werkzeuge for application-specific recommendations or to request compatible inserts. P4841C-5R-A57 WKP35S — Drilling/boring indexable insert, Tiger‑tec Silver, for steel and cast iron | Walter Tools The P4841C-5R-A57 WKP35S is a coated carbide indexable insert from the Tiger‑tec Silver series, designed for drilling and boring applications in steel and cast iron with a geometry tuned for consistent chip formation and process reliability Tiger‑tec Silver coating for extended life Optimised for steel and cast iron machining Geometry 5R‑A57 for predictable chip control WKP35S coated carbide grade for stable wear Greater productivity through coating and grade optimisation The combination of the Tiger‑tec Silver coating and the WKP35S grade delivers improved wear resistance and thermal stability during drilling and boring. By reducing flank and crater wear, the insert maintains cutting performance for longer tool lifetimes, which translates into fewer tool changes and higher machine uptime. The described coating technology is engineered to resist adhesive and abrasive wear commonly encountered when machining both unalloyed and alloyed steels as well as cast irons, supporting a stable, repeatable process. Reliable chip management for safer machining cycles With the 5R‑A57 chipbreaker geometry, this insert promotes controlled chip segmentation and evacuation, reducing the risk of chip entanglement and improving surface integrity. Predictable chip behaviour helps to avoid unexpected tool load peaks and supports more consistent cycle times. For shops transitioning between different grades of steel and grey or nodular cast iron, the geometry and grade combination simplifies setting optimisation and reduces scrap from poor chip control. Practical benefits for workshop and production environments As a drilling and boring indexable insert, the design focuses on repeatable results and straightforward tool handling. The coated carbide construction enables higher cutting parameters compared with uncoated grades while maintaining edge security, supporting productive metal removal rates. Combined with correct toolholder selection and process parameters, the insert contributes to improved throughput and consistent part quality, making it well suited for serial production as well as jobbing work where reliability matters. For application advice or to secure the Walter Tools P4841C-5R-A57 WKP35S for specific machining tasks, contact Metav Werkzeuge by email or phone to discuss process parameters and availability Technical Data Article number: P4841C-5R-A57-WKP35S-WALTER Designation: P4841C-5R-A57 ISO designation: P4841C-5R-A57 WKP35S Product type: Drilling/boring indexable insert Grade: WKP35S Series: Tiger‑tec Silver Facts Geometry: 5R‑A57 Material groups: P (steel), K (cast iron) Special features Coating: Tiger‑tec Silver Base material: Coated carbide Application focus: Drilling and boring Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The P4841C-5R-A57 WKP35S is specified for steel (ISO group P) and cast iron (ISO group K), with the grade and coating optimised for these materials. How does the Tiger‑tec Silver coating improve performance? Tiger‑tec Silver reduces abrasive and adhesive wear on the cutting edge, allowing the P4841C-5R-A57 WKP35S to run at higher parameters with increased tool life and improved process consistency. What role does the 5R‑A57 geometry play? The 5R‑A57 chipbreaker promotes predictable chip segmentation and evacuation, supporting safer machining cycles and more consistent surface finish when using the insert for drilling or boring. Is this insert compatible with standard indexable drill holders? Yes; the insert is designed for use in compatible drilling and boring tool systems that accept the specified ISO-type insert designation and geometry. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P4841C-5R-A57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger·tec Gold coating and the WSP45G grade for consistent performance in drilling and boring operations; the robust 5R‑A57 chipbreaker improves chip control and reduces downtime. Order the insert directly via Metav Werkzeuge or consult our advisors for application-specific recommendations. P4841C-5R-A57 WSP45G indexable insert for drilling and boring (Walter Tools) The P4841C-5R-A57 WSP45G is an indexable insert engineered for precision drilling and boring in demanding metallic materials, offering a PVD-coated carbide solution optimised for production environments. Tiger·tec Gold PVD coating for longer tool life Grade WSP45G: versatile for P / M / S materials Stable chip control with 5R‑A57 chipbreaker Designed for drilling and boring applications Greater durability from advanced coating technology The combination of Tiger·tec Gold and a PVD-coated carbide substrate gives this insert exceptional wear resistance and edge stability under elevated temperatures. The WSP45G grade is designed to maintain a sharp cutting edge for longer tool life, which translates into fewer tool changes and reduced machine downtime. For production-focused operations, the improved resistance to flank wear supports consistent cycle times and a reliable surface finish. Broad material capability for versatile use Rated for P/M/S applications, the insert suits a wide range of parts production. Here, P denotes work on Stahl (unalloyed and alloyed steels), while M identifies performance on rostfreier Stahl, which typically causes higher heat and built‑up edge tendencies. S covers heat‑resistant superalloys and Titan; the grade’s toughness and thermal stability support effective cutting in these challenging materials. This versatility reduces tooling complexity at the tool crib and simplifies inventory management. Precise chip control reduces rework and interruption The integrated 5R‑A57 chipbreaker geometry promotes stable chip formation, breaking and evacuating chips reliably during drilling and boring cycles. Controlled chip flow minimises the risk of surface damage and tool jamming, contributing to uninterrupted production runs. In practice, improved chip control supports a predictable cutting process and can enhance reproducibility of hole geometry and surface quality in serial manufacturing. Designed for process reliability and productivity As an indexable insert tailored for drilling and boring, this component focuses on consistent productivity: repeatable performance, straightforward indexing and predictable wear characteristics. The geometry and coating pairing are selected to balance toughness and wear resistance, making the insert suitable for medium- to high-volume machining where process stability is essential. Integration into established tool systems is straightforward thanks to the standard designation and form factor. Contact Metav Werkzeuge for personalised selection advice on Walter Tools Tiger·tec Gold inserts and to discuss optimal parameters for a given material or cycle — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: P4841C-5R-A57-WSP45G-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte Brand: Walter Tools Grade: WSP45G Series: Tiger-tec Gold ISO designation: P4841C-5R-A57 WSP45G Facts Material groups: P / M / S Chipbreaker: 5R‑A57 Suitable for: drilling and boring applications UID: P4841C-5R-A57-WSP45G-WALTER Special features PVD-coated carbide grade (Tiger·tec Gold) Versatile for Stahl and rostfreier Stahl and heat‑resistant alloys Stable chip formation and reliable cutting edge Indexable insert format for fast replacement FAQ What materials can this insert machine effectively? The P4841C-5R-A57 WSP45G insert from Walter Tools is formulated for machining Stahl, rostfreier Stahl and high-temperature alloys (S group), providing a balanced performance across these material families. How does the 5R‑A57 chipbreaker affect drilling performance? The 5R‑A57 chipbreaker on the P4841C-5R-A57 WSP45G promotes predictable chip formation, which improves evacuation during drilling and boring and reduces the risk of workpiece surface damage. Is the WSP45G grade suitable for serial production? Yes, the WSP45G grade delivers consistent edge stability and wear resistance, supporting long runs and helping to maintain cycle-time consistency in production environments. Can this insert be used for titanium alloys? The insert’s designation includes the S group, indicating capability for heat‑resistant superalloys and Titan; however, cutting data should be adjusted to suit the specific alloy and machine rigidity. What is the main advantage of Tiger·tec Gold coating on this insert? The Tiger·tec Gold PVD coating increases surface hardness and thermal resistance, resulting in extended tool life and more stable cutting performance under elevated temperatures. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names belong to their respective owners. Brand names and registered trademarks are mentioned for explanation only; there is no affiliation between Metav Werkzeuge and the trademark owners. The offered item is an original, factory-new product from Walter Tools.
P4841C-5R-A57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of stable chip formation, the WXP40 uncoated carbide grade and the 5R-A57 chipbreaker for consistent machining results; order the insert directly via Metav Werkzeuge or consult our technical advisors for compatibility checks. P4841C-5R-A57 WXP40 drilling/boring indexable insert — WXP40 grade, 5R-A57 chipbreaker | Walter Tools The P4841C-5R-A57 WXP40 is a drilling and boring indexable insert designed to deliver predictable chip control and repeatable performance in general drilling and bore-enlarging applications. Insert P4841C-5R-A57 in WXP40 grade 5R-A57 chipbreaker for stable chips Uncoated carbide for predictable performance Walter Tools — proven cutting reliability Stable chip control for fewer interruptions The combination of the 5R-A57 chipbreaker and the WXP40 uncoated carbide grade is engineered to promote controlled chip segmentation during drilling and boring operations. The chipbreaker geometry regulates chip flow, which reduces the risk of chip entanglement and minimises machine stoppages. This translates into improved process reliability and fewer manual interventions, enabling smoother production sequences and more consistent component quality. Predictable tool behaviour and process efficiency Being an uncoated carbide insert from an open series, the component offers predictable wear patterns that support process planning and tool-change scheduling. Because tool life and wear progression can be anticipated, machining parameters and cycle times are easier to optimise. The insert’s construction supports stable cutting forces, which contributes to consistent hole quality and repeatable tolerances in serial production or mixed-batch machining. Practical guidance for application and selection Selection must follow the product matrix and machining parameters for the intended workpiece material; the grade WXP40 is an uncoated cemented carbide and its suitability depends on the cutting conditions and material. Where material compatibility is uncertain, refer to the available product documentation and machining charts. The insert is part of an open series that allows flexible integration into existing toolholders and conventional or CNC drilling systems. How the insert supports shop-floor productivity Integration of this indexable insert into regular tool cycles reduces unpredictability at the machine, since the chip control and wear behaviour are defined by the insert geometry and carbide grade. The result is fewer adaptive corrections during runs and a clearer basis for process optimisation. For production environments where steady throughput and consistent hole characteristics are priorities, this insert offers a technically straightforward path to enhanced productivity. For machining tasks that prioritise consistent chip management and reproducible tool behaviour, contact Metav Werkzeuge to discuss the Walter Tools WXP40 grade insert and receive tailored application advice and ordering assistance Technical data Article number: P4841C-5R-A57-WXP40-WALTER Product type: drilling/boring indexable insert Grade: WXP40 Chipbreaker: 5R-A57 Series: Walter Schneidstoffsorte - Serie offen Material designation: Katalogabhängig Facts SKU: P4841C-5R-A57-WXP40-WALTER Uncoated: yes Manufacturer: Walter Tools Application guidance: check product matrix Special features Open series for flexible integration Uncoated cemented carbide grade Chip control geometry for stable chips Intended for drilling and bore-enlarging operations FAQ Which materials is the insert suited for? Suitability depends on the specific workpiece and cutting conditions; the WXP40 grade is an uncoated carbide and material compatibility should be verified against the product matrix before selection. Is the chipbreaker suitable for high-feed drilling? The 5R-A57 chipbreaker is designed to promote stable chip formation in drilling and boring operations; compatibility with high-feed parameters must be tested within the intended machine and material combination. Does the insert come coated? The cutting grade WXP40 is supplied as an uncoated carbide; this provides predictable wear behaviour and supports process planning. How is the insert integrated into tool assemblies? The insert is part of an open series and is compatible with standard indexable insert holders for drilling and boring; correct seating and clamping according to the holder specification is essential. How can tool life be extended with this insert? Consistent cutting parameters, appropriate feeds and speeds, and regular inspection of insert wear help prolong service life; the WXP40 grade offers predictable wear for easier process control. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
P4841C-5R-E57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating and the WKP35S carbide grade for reliable chip control and extended edge life; the insert’s 5R‑E57 chipbreaker stabilises machining in steel and cast iron while reducing unexpected tool changes. Order the insert directly via Metav Werkzeuge or consult the Metav team for application support. P4841C-5R-E57 WKP35S — Drill/Boring Indexable Insert for Steel and Cast Iron by Walter Tools The P4841C-5R-E57 WKP35S is a coated carbide indexable insert developed for drilling and boring operations, offering stable cutting behaviour and predictable chip control across demanding ferrous materials. Tiger·tec Silver coated carbide grade WKP35S Optimised 5R‑E57 chipbreaker for reliable chips Engineered for steel (P) and cast iron (K) Walter Tools quality for consistent edge life Maximised productivity through consistent chip control The optimised 5R‑E57 chipbreaker provides controlled chip segmentation, which directly reduces interruptions caused by chip jamming and manual clearing. In practice, consistent chip formation leads to fewer unplanned stops, improved tool life and more predictable cycle times. The combination of geometry and Tiger·tec Silver surface treatment is designed to maintain a stable cutting edge under the thermal and mechanical loads typical of drilling and boring processes. Reliable performance across steel and cast iron This grade is specified for the ISO groups P (steel) and K (cast iron). That means the insert’s substrate and coating chemistry are balanced to cope with the heat generation and chip shapes encountered when machining unalloyed, alloyed steels and various cast irons. For shops that process mixed batches of ferrous parts, the insert offers a pragmatic solution to reduce tool variants while keeping process security and repeatable results. Coated carbide grade for extended edge life The WKP35S designation denotes a coated carbide grade within the Tiger·tec Silver family. The coating enhances resistance to abrasive wear and thermal softening, which is particularly beneficial when bore diameters and material removal rates demand sustained cutting contact. As a result, surface finish consistency is improved and insert change intervals become more predictable, contributing to lower overall tooling costs. Easy machining integration and predictable results As an indexable insert for drilling and boring, the component integrates into standard tool holders and tooling systems without elaborate setup changes. Its defined geometry enables repeatable positioning and reliable seating, supporting consistent bore tolerances and less rework. Process planners will appreciate the reduced setup variability, while operators benefit from straightforward handling and stable cutting behaviour. Reduced downtime and improved production economics By combining a proven geometry with a high‑performance coating and a grade optimised for ferrous materials, the insert helps reduce the frequency of tool changes and unplanned corrective actions. The end result is a more continuous production flow with predictable tool consumption and improved part quality. The P4841C-5R-E57 WKP35S is therefore a practical choice where process security and consistent output are priorities. For application advice or to secure the P4841C‑5R‑E57 WKP35S for upcoming production runs, contact Metav Werkzeuge GmbH directly at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s consultants provide technical support and delivery coordination Technical data SKU: P4841C-5R-E57-WKP35S-WALTER Designation: P4841C-5R-E57 WKP35S Product type: Drill/boring indexable insert Manufacturer: Walter Tools Series: Tiger·tec Silver Facts ISO designation: P4841C-5R-E57 WKP35S Chipbreaker geometry: 5R‑E57 Material suitability: P (steel), K (cast iron) Special features Coated carbide (Tiger·tec Silver) Grade: WKP35S Application: Drilling / boring operations Stable cutting edge for predictable performance FAQ What materials is this insert designed for? The insert is optimised for machining steel (ISO P) and cast iron (ISO K); the WKP35S grade and Tiger·tec Silver coating address the wear and chip behaviour typical of these material groups. How does the 5R‑E57 chipbreaker affect machining? The 5R‑E57 chipbreaker promotes controlled chip segmentation during drilling and boring, improving chip evacuation and reducing the risk of chip entanglement that can interrupt the cutting process. Is the coating suitable for high temperatures during drilling? Yes, the Tiger·tec Silver coating enhances thermal resistance and reduces abrasive wear, supporting longer edge life under the elevated temperatures encountered in holemaking. Can the insert be used in existing tool holders for indexable drilling? The geometry and designation align with standard indexable drilling systems; compatibility depends on the specific holder but the insert is intended for straightforward integration into common toolholders. What is the SKU and who manufactures this insert? The SKU is P4841C-5R-E57-WKP35S-WALTER and the insert is manufactured by Walter Tools as a Tiger·tec Silver grade. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names belong to their respective owners. Mention of brand names serves explanatory purposes; there is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com