SNMX1205ANN-F57 WKK25G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold performance and the WKK25G grade, optimised for cast iron, combined with a square 90° geometry for stable, repeatable milling operations; order this genuine Walter Tools insert directly via Metav Werkzeuge or consult our specialists for application advice. SNMX1205ANN-F57 WKK25G milling indexable insert — Tiger‑tec Gold, for cast iron (ISO K) — Walter Tools The SNMX1205ANN-F57 WKK25G is a square 90° milling insert from Walter Tools designed for productive machining of cast iron, combining a coated carbide grade with a chipbreaker tuned to brittle, short-chip materials. Tiger‑tec Gold coating Optimised for cast iron (K) Square 90° insert geometry Chipbreaker F57 for stable chips Higher productivity with coating and carbide grade The coated carbide grade WKK25G, part of the Tiger‑tec Gold series, is developed for the abrasive wear characteristics of cast iron. The coating and substrate combination improves wear resistance and edge stability, which extends tool life and reduces the frequency of tool changes. The integrated F57 chipbreaker promotes consistent chip control, lowering the risk of re-cutting and helping to maintain stable material removal rates. These technical properties translate directly into measurable productivity gains on serial milling tasks. Robust geometry for consistent edge life and accuracy The insert’s Square 90° form together with a 0° negative rake provides a robust cutting edge suited to interrupted cuts and heavy engagement strategies common in cast iron roughing. The thickness designation and tolerance class M ensure repeatable seating and dimensional consistency in the toolholder, supporting predictable component accuracy and fewer set‑up adjustments. The combination of geometry and tolerance thus reduces process variation and supports reliable production cycles. Clear application guidance and material fit Classified for ISO K materials, this insert is intended specifically for the short, breaking chips and abrasive nature of cast iron. The design philosophy focuses on stable chip formation and wear resistance rather than versatility across softer metals; the result is a solution tailored to cast‑iron milling where consistent surface quality and extended tool life are priorities. For users seeking to integrate this insert into a production line, the technical attributes are best matched with secure clamping, appropriate coolant or dry strategies as required, and toolholders rated for square inserts to maximise stability. Walter Tools’ grade selection supports reproducible results in demanding foundry and engine component applications. For tailored machining recommendations or to order genuine Walter Tools SNMX1205ANN-F57 WKK25G inserts through Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: SNMX1205ANN-F57-WKK25G-WALTER Product: Milling indexable insert SNMX1205ANN-F57 WKK25G Manufacturer: Walter Tools Facts Size: 12 Thickness designation: 05 Rake/clearance: 0° (negative) Geometry: Square 90° Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKK25G (coated carbide) Chipbreaker: F57 Suitable for: Cast iron (ISO K) Plate form: Square 90° FAQ Is this insert suitable for machining cast iron? Yes. The SNMX1205ANN-F57 WKK25G insert by Walter Tools is specifically designed for ISO K materials and optimised for cast iron applications. What is the benefit of the Tiger‑tec Gold series on this insert? The Tiger‑tec Gold technology combines a coated substrate with a wear‑resistant carbide grade to improve edge life and wear performance during cast iron milling. How does the F57 chipbreaker affect machining? The F57 chipbreaker on this insert promotes short, controlled chips in brittle materials, improving chip evacuation and reducing the likelihood of re‑cutting chips. What does the 0° negative rake mean in practice? A 0° negative rake increases edge strength and is suited to heavy or interrupted cuts, offering durability when machining abrasive or breakable cast iron components. Is the square 90° geometry suitable for roughing operations? Yes. The square 90° form provides strong cutting edges and multiple indexing positions, making it well suited to robust roughing tasks in cast iron. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Markennamen und geschützte Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Brand names and protected trademarks are the property of their respective owners and are mentioned solely for clarification. There is no affiliation between our company and the named brands. The offered article is an original, factory‑new product of the manufacturer Walter Tools.
SNMX1205ANN-F57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, stable chip control and precise seating for reliable milling results; order the insert directly via Metav Werkzeuge or contact the consultants for application advice. SNMX1205ANN-F57 WKP25S milling insert (Square 90°, Tiger‑tec Silver) – Walter Tools The SNMX1205ANN-F57 WKP25S is a square 90° milling insert developed for efficient machining of steel and cast iron, featuring the Tiger‑tec Silver coating and a 0° negative rake for robust performance. Tiger‑tec Silver coated carbide grade WKP25S Square 90° form with 0° negative rake Optimised for steel and cast iron machining Chipbreaker F57 for controlled swarf formation Consistent productivity for steel and cast iron machining The combination of the WKP25S grade and the Tiger‑tec Silver coating delivers a reliable balance between wear resistance and edge stability, which translates into longer tool life and fewer indexings. The insert’s specification targets the ISO material groups P (steel) and K (cast iron), indicating suitability for unalloyed and alloyed steels as well as abrasive cast materials. For operations where thermal load and abrasive wear are decisive, this coated carbide insert provides measurable improvements in process stability and can reduce unplanned downtime through extended service intervals. Secure clamping and repeatable set-up for high‑accuracy milling A square 90° geometry combined with tolerance class M ensures repeatable seating and consistent cutting engagement in the toolholder. The 0° negative rake improves cutting edge strength and reduces tendency for edge chipping under interrupted cuts or heavy engagement. These geometric characteristics support stable machining when high radial or axial forces occur, helping maintain component tolerances and surface finish without frequent re‑adjustment or inspection after each indexing. Controlled chip formation and coating advantages explained The integrated F57 chipbreaker is designed to shape and break chips for typical steel and cast iron cutting conditions, aiding evacuation and reducing the risk of entanglement. The insert material is a coated carbide (described by the Tiger‑tec Silver technology), where a wear‑resistant coating reduces flank and crater wear while the carbide substrate provides mechanical toughness. For users less familiar with the term, the coating is a thin engineered layer that lowers friction and increases temperature resistance, so the cutting edge retains its geometry longer under cyclic loads. Application range and efficiency gains in production Intended as a general‑purpose solution within the Tiger‑tec Silver series, the insert performs well across a spectrum of milling tasks from roughing to semi‑finishing in workshop and shopfloor environments. The specification supports productive machining strategies that favour fewer indexings and predictable tool change intervals, contributing to a lower cost per part. For new set‑ups or when changing workpiece materials, a short trial run is recommended to adapt cut parameters; experienced machining advice is available to fine‑tune speeds and feeds for the specific machine and clamping system in use. Contact Metav Werkzeuge for tailored application advice and to order Walter Tools SNMX1205ANN-F57 WKP25S inserts with Tiger‑tec Silver technology Technical data Article number: SNMX1205ANN-F57-WKP25S-WALTER Designation: SNMX1205ANN-F57 ISO designation: SNMX1205ANN-F57 WKP25S Facts Size: 12 Thickness code: 05 Relief angle: 0° (negative) Tolerance class: M Special features Grade: WKP25S Coating / series: Tiger‑tec Silver Chipbreaker: F57 Shape: Square 90° Material suitability: P / K (steel and cast iron) Execution: X Product type: milling insert (indexable) FAQ What materials is this insert suitable for? The SNMX1205ANN-F57 WKP25S insert from Walter Tools is specified for ISO groups P and K, meaning it is suited to machining steel and cast iron. What does the WKP25S grade offer in practice? WKP25S, as used in the Tiger‑tec Silver family, provides a coated carbide balance of wear resistance and toughness that extends edge life in standard steel and cast iron applications. How does the F57 chipbreaker affect machining? The F57 chipbreaker shapes and fractures the swarf to improve evacuation and reduce the risk of chip interference, which supports stable cutting and clearer chip flow in milling operations. Is the square 90° geometry suitable for heavy milling passes? The square 90° form combined with a 0° negative rake increases edge strength and is appropriate for machining strategies with higher radial loads or interrupted cuts where robustness is required. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX1205ANN-F57 WKP35G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Gold coating and the WKP35G grade for enhanced wear resistance and predictable tool life; the insert’s square 90° geometry and 0° negative rake deliver stable cutting performance in demanding milling tasks. Order directly via Metav Werkzeuge or consult the Metav team for application advice. SNMX1205ANN-F57 WKP35G milling indexable insert — Tiger‑tec Gold, for steel and cast iron — Walter Tools SNMX1205ANN-F57 WKP35G is a milling indexable insert engineered for productive machining of steel and cast iron in industrial milling applications, combining a robust geometry with Walter Tools’ Tiger‑tec Gold technology. Tiger‑tec Gold coated carbide grade WKP35G Square 90° insert geometry 0° negative rake for stable cutting Suited for steel and cast iron machining Higher productivity through engineered coating and grade The Tiger‑tec Gold coating together with the WKP35G carbide composition provides enhanced wear resistance and consistent edge behaviour under cyclical loads. This combination reduces flank and crater wear during medium to heavy milling, which supports longer intervals between index changes and lowers overall tool consumption. The design is particularly suited to production environments where repeatability and predictable tool life are key performance indicators. Robust geometry for process stability and surface quality The square 90° geometry and 0° negative rake create a strong cutting edge that tolerates interrupted cuts and higher radial engagement without chipping. This stability translates into reliable surface finish and dimensional consistency during roughing operations and semi‑finish passes. The neutral rake angle helps to control cutting forces, making the insert a suitable choice for applications that demand both strength and repeatable results. Versatile application across steel and cast iron Classified for material groups P (steel) and K (cast iron) according to ISO 513, the insert accommodates the differing chip formation behaviours of these groups: it handles the ductile, thermally active chips of steel and the abrasive, brittle chips typical of cast iron. The integrated F57 chipbreaker aids controlled chip segmentation, improving evacuation and reducing the likelihood of re‑cutting. Such adaptability makes the component a practical option across mixed‑material production runs. Practical fit for industrial milling cells With a compact size 12 format and thickness 05, plus tolerance class M, the insert fits established cutter bodies for high‑productivity milling. The standardised designation ensures compatibility with common toolholders, simplifying inventory management. The execution marked as X denotes the variant configuration within the series, while the Tiger‑tec Gold series focus ensures consistent coating application and layer properties across batches. These attributes aid process planning and reduce setup variability in serial machining. For application support or to secure a supply of Walter Tools Tiger‑tec Gold inserts, contact Metav Werkzeuge for tailored recommendations and fast delivery — Metav Werkzeuge can advise on cutter compatibility and cutting data, eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: SNMX1205ANN-F57-WKP35G-WALTER Designation: SNMX1205ANN-F57 WKP35G Manufacturer: Walter Tools Facts Size: 12 Thickness: 05 Insert form: Square 90° Relief angle: 0° (negative) Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKP35G Material groups: P / K Chipbreaker: F57 Execution: X Product type: Milling indexable insert FAQ What materials is this insert designed for? The SNMX1205ANN-F57 WKP35G insert is designed for steel (P) and cast iron (K) applications according to ISO 513, benefiting from the WKP35G grade and Tiger‑tec Gold coating. How does the 0° negative rake affect cutting? A 0° negative rake provides a strong cutting edge and greater resistance to chipping under heavy loads, which is why the SNMX1205ANN-F57 WKP35G performs well in interrupted milling and higher engagement operations. Which chipbreaker is integrated and what is its purpose? The insert uses an F57 chipbreaker designed to promote controlled chip segmentation and efficient evacuation when machining both steel and cast iron. Is this insert compatible with standard cutter bodies? The standard designation and size 12 / thickness 05 format mean the insert fits commonly used milling cutter systems; check holder compatibility and seat geometry before assembly. What production benefits can be expected from Tiger‑tec Gold? Tiger‑tec Gold coating improves wear resistance and thermal stability, leading to longer tool life and more consistent performance in serial milling, particularly when paired with the WKP35G grade for steel and cast iron workpieces. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered marks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original, factory‑new goods from the manufacturer (Walter Tools).
SNMX1205ANN-F57 WPP35G WPP35G Wendeplatten - Walter Tools
High-process reliability and extended tool life result from the combination of a robust cutting grade and targeted chip control. Benefit from the Tiger·tec Gold coating together with the F57 chipbreaker and square 90° geometry for efficient steel machining; order the insert directly via Metav Werkzeuge or consult their specialists. SNMX1205ANN-F57 WPP35G – Milling indexable insert, Tiger·tec Gold, for steel by Walter Tools SNMX1205ANN-F57 WPP35G is a square 90° indexable milling insert designed for demanding steel applications, combining a coated cemented-carbide grade with a dedicated chipbreaker for stable material removal Tiger·tec Gold coating for long life Designed for steel machining (P) Square 90° geometry for robust milling F57 chipbreaker for reliable chip control Process security from a modern coating technology The Tiger·tec Gold coating on this grade provides improved wear resistance and consistent performance under the thermal and mechanical loads typical of steel machining. As a coated cemented-carbide solution, the insert sustains cutting edge integrity for longer tool life, which improves uptime and lowers per-part tooling cost. The choice of a coated grade is particularly advantageous where repeatable surface finish and predictable flank wear are required for series production. Geometry and chip control that stabilise machining A square 90° plate form combined with the F57 chipbreaker delivers stable cutting forces and efficient chip formation when working with unalloyed and alloyed steels. The plate’s 0° negative free angle provides a secure cutting edge for interrupted cuts and shoulder milling, while the chipbreaker design reduces recutting of chips. These features translate into fewer tool changes and more consistent cycle times on the machine. Tailored for steel: grade and series benefits The WPP35G grade is developed for the P material class and balances wear resistance with toughness to handle the heat and chip behaviour of steels. Belonging to the Tiger·tec Gold series, the insert offers a universality across a range of steel types—helpful when machines tackle mixed-production runs. The practical result is improved process reliability and a measurable contribution to productivity in milling operations. Practical application and handling advantages The insert’s designation and matching indexable system allow swift seat-and-clamp replacement in compatible toolholders, reducing downtime. The standardised square format and tolerance class M ensure interchangeability within industrial tool inventories. Where operators require simple specification checks, the ISO designation and clear grade marking support fast tool selection and ordering. For production-critical steel machining, contact Metav Werkzeuge to discuss the Walter Tools SNMX1205ANN-F57 WPP35G insert and secure the right cutting strategy for reliable, economical milling. Technical data Article number: SNMX1205ANN-F57-WPP35G-WALTER Product label: Fräswendeschneidplatte SNMX1205ANN-F57 WPP35G Walter Tools Manufacturer: Walter Tools Product type: Milling indexable insert Facts Plate size: 12 Plate thickness code: 05 Free angle: 0° (negative) Plate form: Square 90° Tolerance class: M Chipbreaker: F57 Special features Series / coating technology: Tiger·tec Gold Grade: WPP35G Material suitability: Steel (P) Execution code: X Plate designation: SNMX1205ANN-F57 ISO designation: SNMX1205ANN-F57 WPP35G Sort description: Coated cemented carbide, balanced wear resistance and toughness FAQ What materials is this insert intended for? The SNMX1205ANN-F57 WPP35G insert is intended for the P group (steel), including unalloyed and alloyed steels, as specified by the WPP35G grade. How does the Tiger·tec Gold technology benefit milling operations? Tiger·tec Gold coating on the WPP35G grade improves wear resistance and heat management, resulting in longer tool life and more consistent surface quality when milling steel. Which geometry features support interrupted cuts? The square 90° plate form together with the 0° negative free angle provides a secure cutting edge that is well suited to interrupted cuts and shoulder milling applications. What is the role of the F57 chipbreaker? The F57 chipbreaker is designed to control chip formation and evacuation in steel machining, reducing recutting and helping to stabilise forces during milling. Is this insert compatible with standard SNMX toolholders? The ISO designation SNMX1205ANN-F57 WPP35G indicates compatibility with holders designed for SNMX inserts; confirm holder specifications against the plate designation for interchangeability. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no commercial affiliation between Metav Werkzeuge and the named brands; the offered item is an original, factory-new product of the manufacturer. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
SNMX1205ANN-F67 WAK15 Wendeplatten - Walter Tools
Take advantage of precise chip control, sharp cutting edges and proven suitability for aluminium and other non‑ferrous metals to improve cycle stability and surface quality; order directly via Metav Werkzeuge or request tailored advice from our consultants. SNMX1205ANN-F67 WAK15 — Walter Tools milling indexable insert, uncoated carbide for aluminium, square 90°, 0° (negative) SNMX1205ANN-F67 WAK15 is a square milling insert designed for productive machining of aluminium and other non‑ferrous metals within the Walter N‑series, offering a sharp uncoated cutting edge and a dedicated chipbreaker geometry for stable material removal. Square 90° geometry for versatile milling Optimised for aluminium and non‑ferrous metals Uncoated carbide for sharp edges and low adhesion Chipbreaker F67 for controlled chip formation Consistent performance for non‑ferrous applications The SNMX1205ANN‑F67 WAK15 insert is engineered for reliable performance when machining aluminium and other non‑ferrous alloys. The WAK15 grade is an uncoated carbide formulation that preserves a very sharp cutting edge, reducing built‑up edge and improving surface finish in soft, ductile materials. Combined with the chipbreaker F67, the indexable plate promotes predictable chip segmentation and evacuation, which reduces downtime and minimises secondary operations. This results in measurable productivity gains on production‑oriented machines. Geometry and relief that simplify process planning A square 90° shape and 0° (negative) relief deliver mechanical strength at the cutting edge while enabling versatile toolpaths and stable clamping. The insert’s compact insert size 12 and thickness 05 make it suitable for light to medium engagement milling strategies, where rigidity and repeatability are required. The geometry supports straightforward tool setup and predictable cutting forces, so programmers and operators can rely on consistent cycle times and surface quality across batches. Benefits for workshop efficiency and quality assurance Using the Walter N‑series insert brings practical benefits: lower frequency of insert changes due to the robust edge condition, improved surface finishes thanks to the sharp carbide grade, and reduced risk of material adhesion during cuts. The uncoated carbide composition also simplifies post‑process handling and inspection because there is no coating wear layer to affect tolerance checks. For users seeking a balance of precision and economic machining in non‑ferrous production, this insert offers an efficient choice that integrates with common milling systems. Contact Metav Werkzeuge for application advice and fast delivery — our specialists will recommend the optimal Walter Tools inserts and cutting parameters for specific aluminium alloys and machining setups, email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: SNMX1205ANN-F67-WAK15-WALTER Designation: SNMX1205ANN-F67 WAK15 Manufacturer: Walter Tools Product type: milling indexable insert Facts Insert size: 12 Thickness: 05 Relief angle: 0° (negative) Geometry: square 90° Tolerance class: M Special features Grade: WAK15 (uncoated carbide) Series: Walter N‑series Chipbreaker: F67 Application: aluminium and non‑ferrous metals Execution: X Material group: N (non‑ferrous metals) FAQ What materials is this insert best suited for? The SNMX1205ANN‑F67 WAK15 insert is designed specifically for aluminium and other non‑ferrous metals; the WAK15 grade and F67 chipbreaker reduce adhesion and support clean chip control. Is the insert coated or uncoated? This Walter Tools insert is an uncoated carbide grade (WAK15), chosen to maintain a sharp cutting edge and minimise material sticking when machining soft alloys. How does the F67 chipbreaker affect machining? The chipbreaker F67 provides defined chip segmentation and improved evacuation, which enhances process stability and reduces the risk of long, stringy chips in non‑ferrous machining. What geometry and relief does the insert have? The insert features a square 90° geometry with a 0° (negative) relief, offering a robust cutting edge for versatile milling operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand presence: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered item is original and factory new.
SNMX1205ANN-F67 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance, the F67 chipformer for controlled chip breaking, and the robust square 90° geometry for stable milling operations; order directly via Metav Werkzeuge or consult the team for application advice. SNMX1205ANN-F67 WKP25S – Milling indexable insert, Tiger·tec Silver, for Stahl and cast iron, Walter Tools The SNMX1205ANN-F67 WKP25S is a square 90° milling insert with a 0° negative rake, designed for reliable high-productivity machining of Stahl and cast iron components. *Tiger·tec Silver coating for improved wear resistance *Optimised for Stahl and cast iron machining *Square 90° form with 0° negative rake *F67 chipformer for controlled chip breaking Consistent performance where predictable results matter The SNMX1205ANN-F67 WKP25S belongs to the Tiger·tec Silver series and combines a coated carbide substrate with the WKP25S grade to deliver consistent wear behaviour in demanding milling cycles. Designed for the ISO material groups P and K (see ISO 513), the insert addresses the typical thermal and abrasive conditions of machining Stahl and cast iron. The result is a predictable tool life and fewer tool changes, which directly supports higher machine utilisation and a steadier production flow. The combination of coating technology and grade selection makes the insert particularly suitable where both economy and repeatable part quality are priorities. Better chip control and stable cutting geometry for safe production The integrated F67 chipformer promotes efficient chip breaking and evacuation, reducing the risk of built-up edge and machine stoppages. The Square 90° shape with a 0° negative rake creates a rigid cutting geometry that enhances process stability under interrupted cuts or heavy engagement. For machining operations that require regular surface quality and dimensional reliability, this geometry assists in maintaining cutting forces within predictable limits. The term chipformer refers to the engineered topography on the insert that shapes the chip during cutting; controlled chips mean less manual intervention and cleaner swarf handling at the machine. Straightforward specification and production-ready integration Available in size 12 with thickness 05 and tolerance class M, the insert is specified for straightforward replacement in compatible milling cutters and tool holders. The WKP25S grade is a coated tungsten-carbide solution tuned for broad applicability across Stahl and cast iron workpieces, delivering a balance between economy and lifetime. Process planners will appreciate the clear designation and series information when matching the insert to machining strategies. For additional machining parameters or holder compatibility, technical consultation is advised to ensure optimal feeds and speeds for the chosen workpiece material. Discuss application options with Metav Werkzeuge for optimal use of Walter Tools inserts and request tailored recommendations via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number / SKU: SNMX1205ANN-F67-WKP25S-WALTER Designation: SNMX1205ANN-F67 WKP25S Manufacturer: Walter Tools Facts Size: 12 Thickness: 05 Free rake: 0° (negative) Plate form: Quadrat 90° Tolerance class: M Special features Series: Tiger·tec Silver Grade: WKP25S Chipformer: F67 Grade material: coated carbide Applicable material groups: P / K (Stahl / cast iron) Execution: X FAQ Which materials is this insert suited for? The SNMX1205ANN-F67 WKP25S from Walter Tools is specified for ISO groups P and K, meaning it is tailored for machining Stahl and cast iron workpieces. What does the F67 chipformer achieve? The F67 chipformer on the insert shapes and breaks chips reliably during milling; this reduces swarf handling issues and contributes to a stable process when using the Walter Tools SNMX1205ANN-F67 WKP25S insert. How does the 0° negative rake affect cutting? A 0° negative rake generates a robust cutting edge and higher process stability, which is beneficial for heavy milling or interrupted cuts when using the SNMX1205ANN-F67 WKP25S insert. Is the Tiger·tec Silver series suitable for high-production environments? Yes, the Tiger·tec Silver series, as used in this insert, is designed for good wear resistance and broad material coverage, supporting productive and repeatable milling operations. What tolerance and dimensions are specified for this insert? The insert is listed with tolerance class M, size 12 and thickness 05; these specifications help to match the SNMX1205ANN-F67 WKP25S to appropriate cutter bodies. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are mentioned only for explanation. There is no affiliation between the seller and the manufacturers named. The offered item is an original, brand-new product from the manufacturer Walter Tools.
SNMX1205ANN-F67 WKP35G Wendeplatten - Walter Tools
Taking advantage of the Tiger‑tec Gold technology and the wear-resistant WKP35G grade, this insert delivers consistent edge stability when machining steel and cast iron; its square 90° form and 0° negative relief provide reliable geometry for robust milling operations. Order directly via Metav Werkzeuge or request application advice from our consultants. SNMX1205ANN-F67 WKP35G — Milling indexable insert, square 90°, Tiger‑tec Gold (Walter Tools) A robust SNMX1205ANN-F67 WKP35G indexable milling insert engineered for productive machining of steel and cast iron, featuring Tiger‑tec Gold coating and a square 90° geometry for stable cutting performance Tiger‑tec Gold coating for edge stability Suitable for steel (P) and cast iron (K) Square 90° geometry for versatile milling Chipbreaker F67 for controlled chip formation Greater productivity through stable cutting performance The Tiger‑tec Gold coating and the WKP35G cutting grade combine to improve wear resistance and maintain a sharp cutting edge over extended cycles. Designed for demanding milling, this insert reduces the frequency of tool changes, increasing net machining time and lowering process interruptions. The chipbreaker F67 promotes predictable chip control, which supports higher feed rates while preserving surface quality. Such technical characteristics are particularly valuable in series production where repeatability and uptime are decisive. Clear advantages in machining steel and cast iron Conforming to ISO material groups P (steel) and K (cast iron), the geometry and substrate selection are tailored to the thermal and abrasive conditions typical of these workpiece families. The term P denotes suitability for unalloyed and alloyed steels, with a focus on managing heat and continuous chips; K identifies effectiveness on abrasive cast materials with short, breaking chips. By matching the insert to these classes, process reliability and tool life are optimised without complex parameter adjustments. Robust geometry for universal milling applications The square 90° plate form with 0° negative relief provides a stable cutting edge and straightforward seat positioning in standard toolholders. This geometry supports face and shoulder milling with consistent contact conditions and reduced risk of chipping under heavier cut engagements. The insert’s tolerance class M ensures dimensional consistency for repeatable clamping and predictable tool behaviour across production batches. Practical selection and application guidance The SNMX designation and the F67 chipformer make this insert a practical choice for operations requiring a balance of material removal rate and surface integrity. When paired with appropriate cutting data for the targeted steel or cast iron grade, the combination of Tiger‑tec Gold technology and WKP35G grade offers measurable improvements in tool life and process stability. For specific cutting speeds and feeds, consult technical sheets or contact a specialist to align parameters with machine capability and workpiece hardening. Contact Metav Werkzeuge today for tailored cutting data, availability of Walter Tools SNMX1205ANN-F67 WKP35G inserts and expert advice on optimal toolholder selection Technical Data Article number: SNMX1205ANN-F67-WKP35G-WALTER Name: SNMX1205ANN-F67 WKP35G Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Plate size: 12 Plate thickness: 05 Relief angle: 0° (negative) Tolerance class: M Special features Plate form: Square 90° Grade: WKP35G Chipbreaker: F67 Execution: X Material suitability: P (steel), K (cast iron) FAQ What materials is this insert designed for? The insert is engineered for steel (P) and cast iron (K) applications; the WKP35G grade and Tiger‑tec Gold technology address both the thermal behaviour of steels and the abrasive nature of cast materials. How does the Tiger‑tec Gold technology benefit tool life? Tiger‑tec Gold coating on the SNMX1205ANN-F67 WKP35G improves edge stability and wear resistance, which typically extends tool life and supports sustained productivity in milling operations. What does the 0° negative relief mean for stability? A 0° negative relief produces a robust cutting edge and secure seating in the toolholder, lowering the risk of chipping during heavy cuts and providing stable engagement for face and shoulder milling. Is the chip formation predictable with chipbreaker F67? Yes, the F67 chipbreaker promotes controlled chip fragmentation, aiding evacuation and reducing the chance of long, tangled chips that can affect surface finish and machine safety. Can this insert be used in standard square toolholders? The square 90° geometry is compatible with common square-seat toolholders; the M tolerance class supports consistent clamping and repeatable positioning for series production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarked names and product designations are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer Walter Tools.
SNMX1205ANN-F67 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and a purpose-built F67 chipbreaker for consistently productive machining of steel; the robust square 90° form and negative 0° rake enable heavy cuts with controlled chip formation. Contact Metav Werkzeuge for tailored grade recommendations and production support. SNMX1205ANN-F67 WPP35G milling insert — square 90°, for steel — Walter Tools The SNMX1205ANN-F67 WPP35G is a square milling insert designed for reliable, high-productivity machining of steel components in demanding production environments. Tiger·tec Gold coating for high wear resistance Optimised F67 chipbreaker for stable chip control Square 90° geometry for versatile milling Negative 0° rake for heavy-duty cutting Higher throughput through a wear-resistant grade The combination of the Tiger·tec Gold coating and the WPP35G grade delivers enhanced wear resistance and thermal stability during continuous milling of steels. The coated carbide composition is engineered to tolerate the typical heat and chip formation of ISO P materials, which translates into longer tool life and fewer index changes. In production terms, this means reduced downtime and more predictable cycle times, supporting a steady output rate and improved process efficiency. Precise chip control and secure cutting performance The F67 chipbreaker is optimised for steel machining and promotes short, controllable chips even under higher feed rates. The insert’s square 90° form and negative 0° rake create a robust cutting edge that resists deformation during interrupted cuts and heavy engagements. For workshops without in-depth carbide metallurgy knowledge, the term "chipbreaker" denotes a surface geometry that shapes chips to avoid tangling and to ease evacuation, improving both surface quality and operator safety. Designed for integration and process reliability With tolerance class M and a compact plate size, this insert fits common milling toolholders and repeatable tool systems. The WPP35G grade targets steel (ISO P) applications and offers a balanced blend of toughness and wear resistance for a wide range of steels—from less demanding to more abrasive batches. Consistent indexable performance supports reliable batch-to-batch reproducibility, which is especially valuable where dimensional accuracy and uptime are critical. For specific machining strategies or parameter recommendations, Metav Werkzeuge can assist with feed and speed guidance tailored to the workpiece and machine capability. Contact Metav Werkzeuge for customised cutting data and grade matching for Walter Tools inserts to ensure optimal performance in steel machining applications Technical data SKU: SNMX1205ANN-F67-WPP35G-WALTER Article: Fräswendeschneidplatte SNMX1205ANN-F67 WPP35G Walter Tools Product type: Milling insert Manufacturer: Walter Tools ISO designation: SNMX1205ANN-F67 WPP35G Facts Plate size: 12 Thickness: 05 Free angle: 0° (negative) Chipbreaker: F67 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP35G (coated carbide) Plate form: Square 90° Execution: X Material application: Steel (ISO P) Story trigger: wendeplatten FAQ What materials is this insert suited for? The SNMX1205ANN-F67 WPP35G insert is formulated for steel (ISO P) and performs well across a broad range of unalloyed and alloyed steels. How does the F67 chipbreaker affect machining? The F67 chipbreaker on the WPP35G grade shapes chips to be short and controllable, improving chip evacuation and surface finish during medium to heavy milling of steel. Is the negative 0° rake suitable for heavy cuts? Yes; the negative 0° rake and square 90° geometry provide a robust cutting edge that withstands greater radial and axial forces, making it suitable for heavier engagements. Can this insert be used in high-speed milling? The Tiger·tec Gold coating enhances thermal resistance, which supports higher cutting speeds in many steel applications; machining parameters should be adapted to machine rigidity and coolant strategy. What does tolerance class M mean for toolholders? Tolerance class M indicates standardised manufacturing precision; the SNMX1205ANN-F67 format ensures reliable fit and repeatability in compatible milling cutter bodies. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX1205ENN-F57 WKK25G Wendeplatten - Walter Tools
Take advantage of Tiger‑tec Gold technology and the WKK25G grade for reliable cast‑iron machining; the square 90° design with a 0° negative relief ensures robust cutting and consistent chip control. Order the insert directly via Metav Werkzeuge or ask the Metav consultants for application support. SNMX1205ENN-F57 WKK25G milling indexable insert — Tiger‑tec Gold, cast‑iron application — Walter Tools The SNMX1205ENN-F57 WKK25G is a square, negative‑geometry milling insert developed for efficient machining of cast iron, combining Tiger‑tec Gold coating with a dedicated chipbreaker for stable cutting. Tiger‑tec Gold coating for high wear resistance Optimised for cast iron machining (ISO group K) Square 90° insert, 0° negative relief Increased productivity through durable coating and grade The combination of Tiger‑tec Gold technology and the WKK25G grade delivers enhanced wear resistance and longer tool life when machining abrasive cast‑iron materials. The coated cemented carbide substrate resists abrasive flank wear, which translates into fewer indexings and longer productive running times. As a result, cycle times can be reduced by maintaining cutting parameters closer to optimal values for longer periods, improving overall process efficiency and lowering unit costs without compromising component quality. Stable machining and reliable chip control for repeatable results Designed with a dedicated F57 chipbreaker and a Square 90° shape, the insert promotes consistent chip formation and evacuation during interrupted cuts typical of cast‑iron work. The 0° negative relief delivers a robust cutting edge that tolerates heavier depths of cut and adverse cutting conditions, enhancing stability in milling operations. This geometry supports predictable forces and vibrations, which helps to achieve uniform surface quality and repeatable dimensional results across production batches. Application insight and material suitability explained The cutting grade is specifically tuned for the ISO group K (cast iron), addressing the abrasive wear and typically short, brittle chips of these materials. The tolerance class M indicates medium dimensional precision for consistent seating and interchangeability in standard toolholders. The chipbreaker function reduces the risk of entangling chips and supports safer handling while maintaining good surface finishes. For shops seeking a balance between economy and dependable performance in cast‑iron milling, this insert offers a straightforward, technically sound solution. For machining cast iron with proven Tiger‑tec Gold performance, contact Metav Werkzeuge for detailed application advice or to arrange procurement via Metav Werkzeuge; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: SNMX1205ENN-F57-WKK25G-WALTER Designation: SNMX1205ENN-F57 WKK25G Product type: milling indexable insert Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WKK25G Execution: X Tolerance class: M Data Insert size: 12 Thickness: 05 Free angle: 0° (negative) Geometry: Square 90° Chipbreaker: F57 Special features Coating / technology: Tiger‑tec Gold Cutting grade: WKK25G Material suitability: Cast iron (K) Robust negative geometry for stable cutting Square insert for secure clamping FAQ What materials is this insert suitable for? The SNMX1205ENN-F57 WKK25G by Walter Tools is formulated for machining cast iron (ISO group K) and is optimised to cope with abrasive wear typical of that material. How does the F57 chipbreaker affect machining? The F57 chipbreaker integrated in the SNMX1205ENN-F57 WKK25G promotes controlled chip formation and evacuation, improving surface finish and reducing the likelihood of chip entanglement during milling. Can the insert be used for heavy cutting depths? The 0° negative relief and square 90° geometry provide a robust cutting edge for heavier depths of cut and interrupted milling operations, offering increased stability in demanding conditions. What does the WKK25G grade mean in practice? WKK25G is a Walter Tools cutting grade within the Tiger‑tec Gold family aimed at cast‑iron applications; it balances wear resistance and toughness to extend tool life under abrasive conditions. Is this insert compatible with standard toolholders? The SNMX1205ENN-F57 WKK25G is manufactured to tolerance class M and the common SNMX ISO designation, allowing interchangeability with holders designed for square 90° inserts following the same standards. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. The mentioned brand is included for descriptive purposes only. The offered item is an original, factory‑new product from the manufacturer. The Walter AG (brand appearance: Walter Tools) is part of the Sandvik Group.
SNMX1205ENN-F57 WKP25S Wendeplatten - Walter Tools
Combining Tiger‑tec Silver coating and the WKP25S grade, this insert provides reliable wear resistance and controlled chip formation for steel and cast iron machining. The square 90° form with an F57 chipbreaker ensures repeatable surface quality and stable cutting behaviour. Order the SNMX1205ENN‑F57 WKP25S directly via Metav Werkzeuge or ask our consultants if needed. SNMX1205ENN-F57 SNMX1205ENN-F57 WKP25S — milling indexable insert for steel and cast iron | Walter Tools The SNMX1205ENN‑F57 WKP25S is a coated-carbide milling insert designed for demanding steel and cast iron operations; its negative 0° relief and square 90° form suit interrupted cuts and robust machining tasks Tiger‑tec Silver coating technology WKP25S grade for steel and cast iron Square 90° form for stable mounting F57 chipbreaker for controlled chips High productivity through consistent wear resistance The insert’s core advantage is its Tiger‑tec Silver coating paired with the WKP25S coated‑carbide grade, which together deliver extended tool life and predictable flank wear. This combination reduces the frequency of index changes and supports longer uninterrupted production runs. Stable chip formation from the F57 geometry minimises clogging and eases chip evacuation, leading to fewer machine stops and improved overall throughput. Predictable surface quality and secure cutting geometry A square 90° form and the 0° (negative) relief create a rigid cutting edge that resists edge chipping during interrupted cuts or heavy engagement. The F57 chipbreaker is tuned to produce short, manageable chips in P (steel) and K (cast iron) groups, which supports consistent surface finish and dimensional stability. The tolerance class M contributes to repeatable seating and indexing in multi‑insert holders, helping to maintain process consistency across batches. Easy integration and practical handling in production With a clearly defined insert form and series, integration into existing toolholders and systems is straightforward. The standardised geometry supports quick indexing and reduces setup variation, while the coated design lowers the need for frequent tool changes. For applications requiring robust performance in mixed steel and cast‑iron runs, this insert offers a balance between durability and precision that favours predictable cycle times and efficient machining. For tailored application advice or a quotation for the SNMX1205ENN‑F57 WKP25S in the Tiger‑tec Silver series, contact Metav Werkzeuge’s technical team at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the optimal grade and geometry for the intended material and cutting parameters. Technical data SKU: SNMX1205ENN-F57-WKP25S-WALTER Label: Fräswendeschneidplatte SNMX1205ENN-F57 WKP25S Walter Tools Series: Tiger-tec Silver Grade: WKP25S Manufacturer: Walter Tools Facts Insert form: Square 90° Size: 12 Thickness: 05 Relief angle: 0° (negative) Chipbreaker: F57 Tolerance class: M Special features Coated‑carbide technology Suitable for steel (P) and cast iron (K) Robust geometry for interrupted cuts Optimised chip control for reliable evacuation FAQ What materials is this insert suitable for? The SNMX1205ENN‑F57 WKP25S is specified for machining steel (P) and cast iron (K) material groups according to its WKP25S grade and Tiger‑tec Silver coating. How does the F57 chipbreaker benefit production? The F57 chipbreaker on this insert produces short, controllable chips that improve chip evacuation and surface quality when cutting steel and cast iron. Is the negative 0° relief suitable for interrupted cuts? Yes. The 0° (negative) relief increases edge strength on the SNMX1205ENN‑F57, making it well suited to interrupted cuts and applications with variable engagement. Can this insert be used in existing square‑insert toolholders? The square 90° form and standard tolerance class M facilitate integration into compatible toolholders and support reliable indexing and repeatability. What does the Tiger‑tec Silver series provide? Tiger‑tec Silver coating enhances wear resistance and thermal stability, leading to longer tool life and steadier machining performance with the WKP25S grade. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are used solely for explanation. There is no affiliation between our company and the named brands; the offered item is an original, factory‑new product from the manufacturer.
SNMX1205ENN-F57 WKP35G Wendeplatten - Walter Tools
Take advantage of the proven Tiger·tec Gold coating and the WKP35G grade for reliable chip control and extended tool life; the SNMX1205ENN-F57 family combines robust square geometry and a controlled chipformer for productive milling of steel and cast iron. Order directly via Metav Werkzeuge or consult our specialists for application guidance. SNMX1205ENN-F57 WKP35G — square 90° milling insert, Tiger·tec Gold, suitable for steel and cast iron, Walter Tools The SNMX1205ENN-F57 WKP35G is a square 90° indexable milling insert optimised for productive machining of steel (P) and cast iron (K) with a Tiger·tec Gold coating for extended performance Tiger·tec Gold coating for long tool life Optimised chipformer F57 for controlled chips Square 90° geometry for versatile milling Suitable for steel and cast iron (P / K) Productive chip control for consistent surface quality The combination of the WKP35G grade and the Tiger·tec Gold coating ensures consistent chip control and improved wear resistance when machining steel and cast iron. The integrated chipformer F57 is designed to break and evacuate chips reliably, which reduces rework and supports a stable cutting process. For workshops running mixed batches, this leads to fewer tool changes and a more predictable surface finish on workpieces. Geometry and clamping for secure, repeatable performance The square 90° plate form and negative 0° rake promote rigidity during milling operations, making the insert well suited to plunge and face milling where stability matters. The ISO-style designation facilitates straightforward toolholder matching and exchange. The execution X and tolerance class M help ensure reproducible seating and clamping, contributing to constant machining results and reduced setup times. Versatile use and economical inventory management Thanks to its ISO-style reference and broad material suitability (P / K), this indexable plate is a practical choice for job shops and production lines seeking to streamline tooling inventories. The combination of a coated, wear-resistant grade and a robust chip control geometry delivers long in-service life, lowering the frequency of replacement and supporting cost-efficient production without compromising productivity. Practical recommendations for reliable machining For best results with steels and cast irons, select feeds and speeds that match the work material and machine rigidity; the robust chipformer and coating respond well to stable cutting conditions. The plate thickness and square shape provide resistance to deflection, so the insert performs steadily under interrupted cuts and moderate depths of cut. When in doubt about parameter ranges, Metav Werkzeuge can advise on starting values for the specific component and setup. For tailored advice on using this Walter Tools milling solution and fast supply, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and ordering assistance. Technical data Article number / SKU: SNMX1205ENN-F57-WKP35G-WALTER Designation: SNMX1205ENN-F57 WKP35G Product type: Fräswendeschneidplatte (milling insert) Manufacturer: Walter Tools Core specifications Plate form: Quadrat 90° Size: 12 Plate thickness: 05 Free angle: 0° (negativ) Chipformer: F57 Tolerance class: M Design & features Series: Tiger·tec Gold Grade: WKP35G (coated carbide) Material suitability: P (steel), K (cast iron) Execution: X Indexable plate geometry for stable clamping FAQ What materials is this insert suitable for? The SNMX1205ENN-F57 WKP35G indexable milling insert from Walter Tools is suitable for machining steel (P) and cast iron (K), with the WKP35G grade optimised for these material groups. How does the F57 chipformer affect machining? The F57 chipformer promotes controlled chip breaking and evacuation, which helps to maintain a stable cutting process and consistent surface quality when using this Walter Tools plate. Which geometry makes this insert useful for versatile milling tasks? The square 90° geometry combined with a negative 0° rake provides rigidity and repeatable positioning, making the insert appropriate for a variety of milling operations including face and plunge milling. Can the SNMX1205ENN-F57 WKP35G be used in mixed-production environments? Yes, the ISO-style designation and material versatility (P / K) make this Walter Tools insert a practical option for shops running mixed batches, easing inventory management and tool exchanges. Is the grade coated and what benefit does that bring? The WKP35G grade is part of the Tiger·tec Gold coating family, offering enhanced wear resistance and tool life under typical cutting conditions for steel and cast iron. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
SNMX1205ZNN-F57 WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, precise square geometry and reliable chip control for consistent, productive milling of cast iron; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. SNMX1205ZNN-F57 WKK25G indexable milling insert — Tiger‑tec Gold, for cast iron, square 90°, Walter Tools SNMX1205ZNN-F57 WKK25G is an indexable milling insert engineered for stable, productive machining of cast iron components, offering a robust edge and tailored chip control for industrial milling operations Tiger‑tec Gold coating for high wear resistance Optimised for cast iron (ISO group K) Square 90° geometry for robust milling Chipbreaker F57 for short, controlled chips Increased tool life and process stability for abrasive cast iron work The Tiger‑tec Gold coating combined with the WKK25G grade addresses the typical abrasive wear and short, breaking chips of cast iron. This results in extended tool life and fewer tool changes, which reduces downtime and raises overall productivity. The combination of coating and substrate is engineered for stable chip formation, so operations benefit from consistent cutting behaviour even under interrupted cuts or challenging cast-iron microstructures. For production environments aiming to lower tooling costs per part, this insert delivers a measurable improvement in run time and repeatability. Robust geometry for heavy milling and reproducible surface quality A square 90° form and a 0° (negative) rake deliver a strong cutting edge that resists chipping under high radial loads. The insert’s geometry is designed to offer secure edge stability during heavy machining, supporting higher depths of cut with predictable forces. The integrated chipbreaker F57 aids in creating short, manageable chips that reduce recutting and improve surface finish. These features together provide manufacturers with reproducible component quality and fewer scrap parts when machining cast iron workpieces. Ease of integration and consistent productivity in series production As an indexable insert from Walter Tools, this grade is suitable for automated tool change systems and standard milling cutters that accept SNMX-style inserts. The standardised form and tolerance class allow quick indexing and reliable clamping, minimising process variation between shifts. With the insert optimised specifically for cast iron, process engineers obtain predictable tool behaviour across production batches, improving cycle-time stability and simplifying tool inventory management. The predictable performance supports planning for maintenance intervals and reduces unforeseen stoppages. For dependable cast-iron milling with Walter Tools’ Tiger‑tec Gold technology, contact Metav Werkzeuge for availability and application guidance – Metav Werkzeuge can advise on cutter compatibility and batch supply to meet production needs. Technical data SKU: SNMX1205ZNN-F57-WKK25G-WALTER Product: indexable milling insert SNMX1205ZNN-F57 WKK25G Manufacturer: Walter Tools Facts Insert size: 12 Plate thickness: 05 Free rake angle: 0° (negative) Corner angle: 90° Tolerance class: M Special features Coating: Tiger‑tec Gold Grade: WKK25G Chipbreaker: F57 Geometry: square 90° Material group suitability: cast iron (ISO group K) Series: Tiger‑tec Gold Execution: X FAQ Is this insert suitable for machining cast iron? Yes. The SNMX1205ZNN-F57 WKK25G insert from Walter Tools is optimised for cast iron (ISO group K) and offers coating and grade characteristics tuned to abrasive cast-iron conditions. What benefit does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold coating on this insert improves wear resistance and extends tool life under abrasive cutting conditions, which is particularly beneficial when machining cast iron components. How does the chipbreaker F57 affect machining performance? The F57 chipbreaker promotes short, controlled chips that reduce recutting and help maintain a consistent surface finish; this leads to more stable processes and easier chip evacuation. Can the insert be used in standard SNMX cutter systems? The insert follows the SNMX geometry and tolerance class, so it is compatible with standard SNMX-style milling cutters that accept this format and clamping. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names are used solely for explanation and identification of compatible products. The item offered is an original, factory‑new product from the manufacturer.
SNMX1205ZNN-F57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of high process security, broad material coverage and a stable cutting geometry for efficient milling cycles; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. SNMX1205ZNN-F57 WKP25S – milling indexable insert, Tiger·tec Silver, square 90° (Walter Tools) The SNMX1205ZNN-F57 WKP25S is a square 90° milling insert engineered for productive machining of steel and cast iron in demanding milling operations. Tiger·tec Silver coating for process reliability WKP25S grade for steel and cast iron machining Square 90° form for stable cutting edges Negative 0° relief for robust interrupted cuts Reliable metal removal with consistent chip control The insert’s core advantage is its Tiger·tec Silver coating combined with a coated carbide substrate, designed to deliver consistent chip control and extended edge life. This combination reduces flank wear and lowers the frequency of index changes in continuous production runs, which contributes to tangible productivity gains. The geometry and coating work together to moderate temperature at the cutting edge, so cycle times can be maintained under stable conditions while keeping surface finish demands within tighter tolerances. Optimised for steel and cast iron applications Designed to address the ISO groups P (steel) and K (cast iron), the grade WKP25S provides a balance between toughness and wear resistance suitable for a broad range of steels and grey or nodular cast irons. For steel, the grade copes with the heat and continuous chips typical of alloyed and unalloyed steels; for cast iron, the insert’s abrasion resistance and tailored chipbreaking help to control short, fragmented chips. This makes the tool a practical choice where versatility across different workpiece materials is required without frequent tool changes. Geometry that promotes stability and repeatability The square 90° insert form and negative 0° relief deliver a robust edge for interrupted cuts and heavy engagement milling. The listed F57 chipbreaker is tuned to produce manageable chip shapes in mid-range feeds, reducing the risk of chip entanglement and helping coolant access. The tolerance class M supports repeatable seating and indexing in standard toolholders, ensuring positional accuracy between index changes. Overall, this geometry is aimed at stable, repeatable machining rather than ultra-fine finishing, so it is particularly suitable for roughing and mixed roughing/finishing operations. Integration into production and handling guidance The insert is provided in execution X, intended for common pocket types in modular milling systems; this aids fast replacement and reduces machine downtime. Due to the coated carbide construction and the chosen grade, users can expect predictable wear progression and a clear criterion for index replacement. For customers new to the grade, trialing the insert in a controlled production run is recommended to establish optimal speeds and feeds; the insert’s construction supports a wide processing window, which simplifies initial setup and shortens ramp-up time in serial production. The brand heritage behind the design also supports confidence in consistent manufacturing quality. For process-secure milling with Tiger·tec Silver, contact Metav Werkzeuge to discuss application suitability and availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: SNMX1205ZNN-F57-WKP25S-WALTER Designation: SNMX1205ZNN-F57 WKP25S Product type: milling indexable insert Brand: Walter Tools Series: Tiger·tec Silver Grade: WKP25S Chipbreaker: F57 Execution: X Tolerance class: M Material group: P / K Numbers / Core technical data Size: 12 Thickness: 05 Relief angle: 0° (negative) Special features / Applications Coated carbide (Tiger·tec Silver) Suitable for steel (P) and cast iron (K) Square 90° insert form Robust geometry for interrupted cuts Stable chip control and wear behaviour FAQ What materials can this insert machine effectively? The SNMX1205ZNN-F57 WKP25S insert by Walter Tools is specified for ISO groups P and K, meaning it is suitable for machining both steel and cast iron with reliable chip control. How does the Tiger·tec Silver series improve performance? The Tiger·tec Silver coating on the SNMX1205ZNN-F57 WKP25S increases thermal and abrasion resistance, which leads to longer edge life and better process stability in continuous milling operations. Is the insert suitable for interrupted cuts or heavy engagement? Yes; the square 90° form combined with a negative 0° relief and the F57 chipbreaker makes this insert robust for interrupted cutting and operations with heavy axial or radial engagement. What tolerance and seating accuracy can be expected? With tolerance class M, the SNMX1205ZNN-F57 WKP25S provides repeatable seating and indexing, supporting stable positional accuracy in modular milling toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation or endorsement implied between Metav Werkzeuge and the named manufacturers. The offered item is an original, factory-new product of the listed manufacturer.
SNMX1205ZNN-F57 WKP35G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold combination of wear-resistant coating and a dedicated WKP35G grade to secure consistent chip control and extended tool life; the square 90° geometry with 0° negative rake ensures robust edge support and repeatable seating for stable production. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. SNMX1205ZNN-F57 WKP35G milling insert — Walter Tools, Tiger·tec Gold, for Steel (P) and Cast iron (K), 0° negative rake The SNMX1205ZNN-F57 WKP35G is a square 90° milling insert with a 0° negative rake, designed as a coated carbide grade for demanding steel and cast iron machining applications, offering a balance of wear resistance and chip control Tiger·tec Gold coating, WKP35G for durable cutting Square 90° insert with 0° negative rake Chipbreaker F57 for controlled chip formation Suited to Steel (P) and Cast iron (K) applications High-performance cutting that boosts productivity The combination of Tiger·tec Gold coating and the WKP35G grade is engineered to resist abrasive wear and maintain a sharp cutting edge under continuous loads. The insert’s coated carbide substrate and the F57 chipbreaker are tuned for stable chip formation, which reduces machining interruptions and helps maintain consistent cycle times. Where process reliability and component surface integrity matter, this specification supports longer tool life and fewer changeovers, improving overall shop-floor efficiency. Robust geometry for repeatable seating and fewer tool changes The square 90° form with a 0° negative rake provides solid edge support for interrupted cuts and heavy engagement typical in roughing or mixed operations. The specified tolerance class M ensures consistent dimensions between lots, so insert seating and repeatability are maintained across tool changes. As a result, fixture adjustments and set-up times are minimised and component tolerances are easier to hold, which contributes to lower production variance and increased machine utilisation. Clear material guidance and straightforward process integration This insert conforms to ISO material groupings P and K, meaning it is suitable for a broad range of steel and cast iron applications. For clarity: P indicates suitability for steels (unalloyed and alloyed), while K indicates suitability for cast irons with typically abrasive wear characteristics and brittle chip forms. Integration into existing toolholders is straightforward thanks to the standard SNMX geometry; the F57 chipbreaker supports controllable chip flow across typical cutting parameters. For further technical clarifications or recommendations on cutting data and toolholder pairing, Metav Werkzeuge can provide practical guidance to match the insert to specific machining tasks and production goals. For machining enquiries relating to Walter Tools Tiger·tec Gold inserts, contact Metav Werkzeuge for tailored advice and ordering assistance via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: SNMX1205ZNN-F57-WKP35G-WALTER Article: SNMX1205ZNN-F57 WKP35G Type: milling insert (indexable) Brand: Walter Tools Facts Insert size: 12 Thickness: 05 Free rake: 0° (negativ) Shape: Square 90° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WKP35G (coated carbide) Chipbreaker: F57 Material suitability: Steel (P) and Cast iron (K) Execution: X FAQ What materials is this insert suitable for? The SNMX1205ZNN-F57 WKP35G insert from Walter Tools is specified for ISO groups P and K, making it suitable for steel and cast iron workpieces. How does the F57 chipbreaker affect machining? The F57 chipbreaker on the SNMX1205ZNN-F57 WKP35G promotes controlled chip formation, which improves evacuation and reduces the risk of entanglement in both steel and cast iron operations. Is the insert compatible with standard SNMX toolholders? Yes, the SNMX1205ZNN-F57 geometry is compatible with toolholders designed for SNMX square inserts and will seat reliably when the correct clamping is applied. What benefit does the 0° negative rake provide? A 0° negative rake enhances edge support and wear resistance during heavy cutting or interrupted cuts, helping to preserve flank life under demanding conditions. Can this insert be used for finishing operations? While optimised for wear resistance and robust cutting, the SNMX1205ZNN-F57 WKP35G can be applied in finishing under appropriate cutting parameters; process validation for surface finish requirements is advised Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is original, brand-new goods from the manufacturer.
SNMX160620-F27 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, the WPP35G grade and the square 90° geometry for a durable, predictable milling solution in steel applications; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. SNMX160620-F27 WPP35G — milling indexable insert by Walter Tools (Tiger‑tec Gold, square 90°) The SNMX160620-F27 WPP35G is a square 90° indexable milling insert from Walter Tools’ Tiger‑tec Gold series, designed for robust and efficient machining of steel with a balanced wear resistance and toughness. Tiger‑tec Gold coating for extended tool life WPP35G grade optimised for steel machining Square 90° shape with 2 mm corner radius Negative 0° rake with F27 chipbreaker Higher throughput through coating and grade selection The Tiger‑tec Gold series and the WPP35G grade combine a coated carbide substrate with an optimised coating stack to extend edge life and reduce downtime. The combination is designed specifically for the thermal and mechanical demands of machining steel, offering a compromise between wear resistance and toughness that suits a wide range of operations. The enhanced coating reduces flank wear and supports more consistent component quality over longer tool life, which improves productivity and lowers the cost per part in serial production. Predictable cutting behaviour thanks to geometry and chip control A square 90° form with a 2 mm corner radius provides a sturdy cutting edge that resists chipping under intermittent or heavy engagement. The 0° negative rake increases edge strength and supports roughing passes where robustness is required, while the F27 chipbreaker controls chip formation during steel cutting to protect workpiece integrity and tool stability. Together, these geometrical features translate into predictable results, easier process set-up and improved surface finish where rigidity and repeatability are priorities. Seamless integration into productive tool systems The insert’s designation supports straightforward replacement routines and repeated indexability in compatible milling cutters, contributing to short machine downtimes and consistent part output. The product is intended for professional machining contexts where process reliability matters; its composition and chip control are aligned with common shop-floor strategies for high-volume steel machining. For toolrooms seeking reliable milling inserts with reduced variation between edges, this insert provides the necessary combination of robustness and chip management to maintain cycle time and part quality. For tailored recommendations on the Walter Tools SNMX160620-F27 WPP35G insert, or to discuss the optimal insert selection for specific steel grades, contact Metav Werkzeuge’s technical consultants at info@metav-werkzeuge.com or call +49 2822 7131930 for application support. Technical data SKU: SNMX160620-F27-WPP35G-WALTER Article designation: SNMX160620-F27 WPP35G Product type: Fräswendeschneidplatte (milling indexable insert) Brand: Walter Tools Series: Tiger‑tec Gold Grade: WPP35G Execution: X Core specifications Corner radius: 2 Inscribed size: 16 Thickness: 06 Free angle: 0° (negativ) Tolerance class: M Materials & special features Coating technology: Tiger‑tec Gold Chipbreaker: F27 Shape: Quadrat 90° Application group: P (steel) Material designation: coated carbide Suitable for machining: steel FAQ What materials is this insert intended for? The SNMX160620-F27 WPP35G insert is designed for machining steel (material group P); the WPP35G grade is specifically balanced for the thermal and chip-formation characteristics of steel. How does the Tiger‑tec Gold coating benefit production? Tiger‑tec Gold on the SNMX160620-F27 WPP35G improves wear resistance and edge stability, which extends tool life and supports more consistent component quality across production runs. What does the 2 mm corner radius mean for part finish and tool life? A 2 mm corner radius increases edge strength and reduces the risk of chipping, improving tool life under heavy loads and helping to achieve a reliable surface finish in robust milling operations. Is the negative 0° rake suitable for heavy-duty milling? Yes; the negative 0° rake on this insert enhances edge robustness, making it appropriate for heavier engagements and intermittent cuts where a stronger cutting edge is required. Which chipbreaker is integrated and what is its purpose? The insert features an F27 chipbreaker that is engineered to produce controlled chips during steel machining, reducing the risk of entanglement and improving process stability. Manufacturer/Responsible: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
SNMX160620-F57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the WKP25S grade for high productivity and consistent chip control in milling Stahl and Gusseisen; the robust square geometry with a 2 mm corner radius ensures repeatable edge stability and predictable tool life. Order directly via Metav Werkzeuge or consult the technical team for application-specific cutting data. SNMX160620-F57 WKP25S – Milling indexable insert, Tiger‑tec Silver, for Stahl and Gusseisen | Walter Tools SNMX160620-F57 WKP25S is a coated milling insert designed for productive face and shoulder milling of Stahl and Gusseisen in industrial machining environments Tiger‑tec Silver coating for high productivity WKP25S grade for Stahl and Gusseisen Square insert 90° with 2 mm corner radius High productivity through proven coating technology The combination of the Tiger‑tec Silver coating and the WKP25S coated carbide substrate provides a measurable increase in process efficiency when machining Stahl and Gusseisen. The coating is formulated for stable wear behaviour and improved thermal resistance, which translates into longer tool life and fewer tool changes during batch runs. As the grade is aligned with ISO cutting group requirements, operators will notice consistent chip formation and reduced flank wear under typical milling parameters. This results in a more reliable production flow and a lower overall tool cost per component. Geometry engineered for stable cutting performance The insert’s square 90° profile combined with a 2 mm corner radius and chipbreaker F57 gives a balance between cutting edge strength and surface finish capability. The 0° (negative) rake angle contributes to a robust cutting edge, particularly beneficial in interrupted cuts or heavier radial engagement. The design maintains dimensional stability and supports predictable insert wear, aiding programming and process planning. Tolerance class M ensures interchangeability and reliable mounting, which supports repeatable machining results across multiple toolholders. Broad application range and process reliability Designed primarily for groups P and K according to ISO 513, this insert is suitable for general-purpose milling in Stahl and Gusseisen applications, where abrasive wear and varying chip forms are common. The chip control geometry combined with the coating means fewer built-up edge events and improved surface integrity on the workpiece. For shops seeking to standardise inserts across variable component families, the SNMX series offers a pragmatic option to reduce complexity while maintaining productivity. For detailed cutting data or optimisation strategies, the technical advisors at Metav Werkzeuge provide application-focused recommendations. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger‑tec Silver inserts and to request cutting data or a suitability assessment via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: SNMX160620-F57-WKP25S-WALTER Designation: SNMX160620-F57 WKP25S Grade / Coating: WKP25S, Tiger‑tec Silver Form: Square 90° Size: 16 Thickness: 06 Corner radius: 2 Chipbreaker: F57 Rake angle: 0° (negative) Tolerance class: M Material application: P / K Facts Insert size: 16 mm Thickness: 06 Corner radius: 2 mm Rake angle: 0° (negative) Tolerance: M Special features Tiger‑tec Silver coating technology WKP25S coated carbide grade Suitable for Stahl and Gusseisen Square geometry 90° Chipbreaker F57 Ausführung: X Serie: Tiger‑tec Silver FAQ Which materials are best machined with this insert? The SNMX160620-F57 WKP25S by Walter Tools is optimised for Stahl (ISO group P) and Gusseisen (ISO group K), providing stable chip control and wear resistance for these material families. What benefits does the Tiger‑tec Silver coating deliver? The Tiger‑tec Silver coating on the WKP25S grade enhances thermal resistance and reduces abrasive wear, resulting in longer tool life and improved process reliability when milling medium to heavy cuts. How does the insert geometry affect surface finish? The square 90° geometry with a 2 mm corner radius and chipbreaker F57 balances edge strength and surface quality, offering predictable wear patterns and consistent finishing for shoulder and face milling operations. Is this insert suitable for interrupted cuts or heavy engagement? Yes, the 0° (negative) rake and the robust edge preparation make this insert well suited to interrupted cuts and applications requiring a durable cutting edge and high process security. Manufacturer: Walter Tools (the Walter AG brand, headquartered in Tübingen, Germany). Protected trademarks and brand names are the property of their respective owners. Brand names are used solely for identification and explanatory purposes. The offered item is original, factory‑new goods of the manufacturer.
SNMX160620-F57 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WPP35G carbide grade for robust, repeatable steel machining; the F57 chipbreaker and square 90° geometry deliver stable chip control and secure clamping. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. SNMX160620-F57 WPP35G Indexable milling insert for steel — Walter Tools The SNMX160620-F57 WPP35G is a square 90° indexable milling insert developed for high-productivity machining of steel, combining a Tiger‑tec Gold coating with an F57 chipbreaker for controlled chip formation. Tiger‑tec Gold coated carbide Optimised chip control F57 breaker Square 90° geometry for stability Corner radius 2 mm for robust cutting Consistent performance through advanced coating technology The Tiger‑tec Gold coating in this insert provides a balanced combination of wear resistance and thermal stability, which is particularly beneficial when machining steel (ISO group P). The WPP35G grade is a coated carbide designed to maintain a stable cutting edge under the heat and forces typical of steel machining, reducing flank wear and helping to extend edge life. As a result, process reliability improves and tool-change frequency is lowered, supporting uninterrupted production cycles and predictable component tolerances. Stable chip control and secure cutting geometry The integrated F57 chipbreaker is engineered for reliable chip formation when removing steel material, promoting efficient evacuation and reducing the risk of built-up edge. The insert’s square 90° profile and 0° negative rake create a robust, vibration‑resistant cutting geometry that supports heavy cuts and interrupted operations. The 2 mm corner radius contributes to stronger cutting edges for roughing passes, improving tool life and surface consistency without sacrificing dimensional control. Simple integration for productive toolpaths The SNMX160620 format and compact dimensions allow straightforward replacement in compatible milling toolholders, enabling rapid index and return to production. The tolerance class M ensures consistent fit and repeatability across inserts, which simplifies tool set‑up and reduces variability between tools. Together with the coated carbide substrate, these characteristics support higher feed rates and longer tool life, translating to improved throughput and lower machining costs per component. Optimised for steel applications and a wide process window This insert is specified for machining steel, including unalloyed and alloyed variants as covered by ISO group P. The combination of the Tiger‑tec Gold coating and the WPP35G tool grade offers a versatile balance between wear resistance and toughness, making it suitable for general milling, face milling and shoulder operations in steel components. For applications outside steel, consult machining data sheets or contact our advisers to verify suitability and cutting parameters. Discuss machining parameters for the SNMX160620-F57 WPP35G with Metav Werkzeuge — our application engineers will recommend the optimal grade and toolholder setup for Walter Tools inserts Technical Data SKU: SNMX160620-F57-WPP35G-WALTER Designation: SNMX160620-F57 ISO designation: SNMX160620-F57 WPP35G Product type: Indexable milling insert Manufacturer: Walter Tools Grade: WPP35G Series: Tiger‑tec Gold Execution: X Tolerance class: M Numbers / Core data Corner radius: 2 mm Insert form: Square 90° Size: 16 Thickness: 06 Relief angle: 0° (negative) Chipbreaker: F57 Special features Coating: Tiger‑tec Gold (coated carbide) Material suitability: Steel (ISO group P) Stable chip control Robust cutting edge for heavy cuts FAQ Which materials is this insert intended for? The SNMX160620-F57 WPP35G is intended for machining steel (ISO group P), where the Tiger‑tec Gold coating and WPP35G grade provide balanced wear resistance and toughness. What are the key geometry specifications of the insert? This square insert features a 90° form, a 2 mm corner radius and a 0° negative rake, combined with the F57 chipbreaker for controlled chip formation. Which machining operations benefit most from this insert? The insert is suitable for general milling tasks in steel, including face milling and shoulder milling, where durable edges and consistent chip control are required. Is the SNMX160620-F57 format compatible with standard SNMX toolholders? The insert uses the SNMX160620 format and is designed for use in compatible indexable milling toolholders; matching the holder to the insert format ensures correct clamping and repeatability. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and brand names remain the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named manufacturers. The offered article is an original, factory‑new product of the manufacturer (Walter Tools).
SNMX160620-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating combined with the WSP45G grade and the F57 chipbreaker to achieve stable chip control and prolonged edge life in steel, stainless steel and superalloy milling; order the SNMX160620-F57 WSP45G directly via Metav Werkzeuge or request tailored advice from our consultants. SNMX160620-F57 SNMX160620-F57 WSP45G – Indexable milling insert for steel, stainless steel and superalloys (Walter Tools) SNMX160620-F57 WSP45G is a square indexable milling insert designed for versatile finishing and light roughing in demanding materials Tiger·tec Gold PVD coating for durable edges Suited to steel, stainless steel and superalloys Square 90° form with 2 mm corner radius Negative 0° rake for stable chip control Greater productivity through a resilient grade and coating The combination of the WSP45G grade and the Tiger·tec Gold coating delivers a balance between toughness and wear resistance that supports longer tool life under common milling workloads. The coated carbide substrate resists abrasive and adhesive wear, which reduces the need for frequent index changes and helps maintain consistent cutting conditions. This leads to measurable process efficiencies: fewer interruptions, more stable cycle times and improved overall productivity for batch and series production. Consistent surface quality with controlled chip formation Designed with a dedicated F57 chipbreaker and a square 90° geometry, the insert promotes predictable chip flow and reduced tendency for built-up edge when cutting heat-prone alloys. The 2 mm corner radius offers a compromise between edge strength and surface finish: it supports robust corner performance while still enabling fine finishing passes. Explained simply, the chipbreaker shapes the chips to avoid entanglement, lowering the risk of re-cutting and helping to achieve repeatable surface quality in one or two passes. Process security and application scope for mixed production This insert is specified for machining groups P / M / S — that is, unalloyed and alloyed steels, stainless steels and heat-resistant superalloys/titanium — making it suitable for workshops handling mixed materials. The 0° negative rake provides a stable cutting edge under variable cutting forces, which is especially beneficial where clamping or machine stiffness may vary. As a result, the insert supports reliable, repeatable results across small and medium batch sizes and reduces trial-and-error at process start-up. Contact Metav Werkzeuge for detailed process recommendations and assistance sourcing Walter Tools SNMX160620-F57 WSP45G; our team can advise on optimum cutting data and immediate supply options Technical data Article number: SNMX160620-F57-WSP45G-WALTER Designation: SNMX160620-F57 WSP45G (indexable milling insert) Manufacturer: Walter Tools Series: Tiger·tec Gold Core data Size: 16 mm Corner radius: 2 mm Thickness code: 06 Rake angle: 0° (negative) Tolerance class: M Plate form: Square 90° Features & applications Grade: WSP45G (Tiger·tec Gold PVD-coated carbide) Chipbreaker: F57 Suitable for: Steel (P), Stainless steel (M), Superalloys/Titanium (S) Execution: X (standard geometry) Series description: Tough, versatile PVD grade for milling applications FAQ What materials is this insert suitable for? The SNMX160620-F57 WSP45G is specified for machining steel, stainless steel and heat‑resistant superalloys (P / M / S), reflecting the grade’s balanced toughness and wear resistance. How does the F57 chipbreaker affect performance? The F57 chipbreaker shapes chips for controlled evacuation and reduces the risk of re-cutting, improving surface finish and process stability during interrupted or continuous milling. What advantage does the 0° negative rake offer? A 0° negative rake provides a more robust cutting edge that tolerates variable cutting forces and improves edge stability, particularly useful when machine stiffness or clamping varies. Can this insert be used for finishing and light roughing? Yes, the square 90° form with a 2 mm corner radius is suitable for finishing passes and light roughing, offering a balance of edge strength and surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned for explanation only. There is no affiliation between our company and the named brands; the offered item is an original, factory‑new product of the manufacturer.
SNMX160640-F57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of high process security, a Tiger·tec Silver cutting grade and precise square geometry for consistent milling results; order the insert through Metav Werkzeuge or consult the technical team for application advice. SNMX160640-F57 WKP35S indexable milling insert by Walter Tools — Tiger·tec Silver, 4 mm corner radius SNMX160640-F57 WKP35S is a square 90° milling insert designed for productive machining of steel and cast iron in general milling applications Tiger·tec Silver coating for long life Suitable for P (Stahl) and K (Gusseisen) Square 90° format with 4 mm radius Negative relief angle 0° for sturdy cutting Boosted tool life through advanced coating technology The Tiger·tec Silver coating and the WKP35S grade combine to offer a robust, coated carbide solution that reduces abrasive wear and extends edge life under typical milling loads. Coated inserts provide a thin protective layer that lowers friction and delays flank wear; this results in fewer indexings and more predictable tool-change intervals. The cutting material classification P / K indicates suitability for P (Stahl) and K (Gusseisen) workpiece groups according to ISO 513, so the insert is appropriate where both steel and cast-iron components are processed. The technological focus on stable chip formation and abrasion resistance helps maintain surface quality over longer production runs. Geometry engineered for stable milling and reliable chip control A square 90° insert with a 4 mm corner radius provides rigidity at the cutting edge and supports higher radial engagement without compromising stability. The chipbreaker F57 is matched to this geometry to encourage controlled, short chips when machining brittle or semi-brittle materials, lowering the risk of entanglement and improving surface finish. The negative relief angle (0°) increases edge strength for interrupted cuts and heavy shoulder milling. Together, these features contribute to repeatable dimensional results and reduced vibration, which is particularly relevant for medium to heavy milling operations where tool robustness is prioritised. Practical advantages for workshop efficiency and process reliability The insert’s tolerance class M and standardised square shape simplify tool management and replacement routines, enabling consistent set-ups across multiple machines. A clearly defined insert thickness and size allow straightforward specification in tool lists and CAM setups, while the coated grade supports sustained machining performance, translating to lower overall tooling costs through extended life and fewer tool changes. Walter Tools’ focus on process security and a stable cutting edge aligns this insert with production contexts demanding both productivity and repeatable results. Contact Metav Werkzeuge GmbH for specification matching or to reserve SNMX160640-F57 WKP35S inserts—email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical guidance and ordering support Technical Data Article number: SNMX160640-F57-WKP35S-WALTER Name: SNMX160640-F57 WKP35S Manufacturer: Walter Tools Series: Tiger-tec Silver Grade: WKP35S Product type: Fräswendeschneidplatte Core dimensions Insert size: 16 Insert thickness: 06 Corner radius: 4 mm Relief angle: 0° (negative) Plate form: Square 90° Tolerance class: M Special features Chipbreaker: F57 Material group suitability: P / K (Stahl and Gusseisen) Execution: X Baureihe: Tiger-tec Silver FAQ What materials is this insert suitable for? The SNMX160640-F57 WKP35S insert is formulated for machining P (Stahl) and K (Gusseisen) workpiece groups, making it suitable for a wide range of steel and cast-iron applications. How does the Tiger·tec Silver grade benefit production? The Tiger·tec Silver coating on this insert reduces abrasive wear and helps maintain a stable cutting edge, which supports longer tool life and consistent surface quality during extended milling operations. Why use a square 90° insert with a 4 mm radius? A square 90° geometry with a 4 mm radius offers enhanced edge strength and rigidity, allowing higher radial engagement and better resistance to shock loads, particularly for shoulder milling and interrupted cuts. What role does the chipbreaker F57 play? The F57 chipbreaker is designed to produce controlled, short chips when machining steel and cast iron, improving chip evacuation and reducing the chance of chip-related interruptions in the machining process. Is this insert suitable for heavier milling and interrupted cuts? Yes; the negative relief angle 0° and robust coated grade make the insert especially suited to heavier milling operations and intermittent cutting conditions where edge strength is critical. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX160640-F57 WSP45G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the robust WSP45G grade for extended tool life and reliable performance in demanding milling tasks; order directly via Metav Werkzeuge or request tailored advice from the consultants if process optimisation is required. SNMX160640-F57 WSP45G square milling insert — Tiger·tec Gold, for Stahl, rostfreier Stahl and superalloys/titanium (Walter Tools) SNMX160640-F57 WSP45G is a square Fräswendeschneidplatte designed for general and heavy milling applications across a wide range of materials; the insert combines a wear-resistant coating with a stable geometry for productive machining in steel, rostfreier Stahl and heat-resistant alloys. Tiger·tec Gold PVD coating for extended tool life WSP45G grade for versatile milling of P/M/S Square 90° insert with corner radius 4 Negative 0° rake for stable heavy cutting High wear resistance for uninterrupted production The SNMX160640-F57 WSP45G insert is built on a coated carbide base and benefits from the Tiger·tec Gold PVD technology, which is formulated to reduce flank wear and maintain a stable cutting edge under high thermal and mechanical loads. For machining operations in Stahl, rostfreier Stahl and high-temperature alloys, the WSP45G grade promotes consistent chip formation and reduces the frequency of index changes. This leads to measurable improvements in process uptime and tool-life economics, since fewer tool changes are required and component tolerances remain stable during longer tool cycles. Geometry engineered for strength and precision The square 90° format with corner radius 4 and a 0° (negativ) rake angle provides a rigid cutting geometry that is especially effective for interrupted cuts and robust engagement. The combination of the insert thickness designation 06 and the tolerance class M supports predictable clamping and repeatable positioning in indexable toolholders, which contributes to consistent surface finishes and dimensional accuracy. The integrated chipbreaker F57 is optimised to control chip flow during medium to heavy milling, thereby reducing the risk of built-up edge and improving component surface quality during both roughing and semi-finishing operations. Reliable choice across diverse applications Designed as a versatile solution, this insert suits a broad production spectrum — from conventional roughing in carbon and alloyed Stahl to demanding machining of rostfreier Stahl and temperature-resistant nickel or titanium alloys. The coated carbide construction and the WSP45G chemistry provide a balance between toughness and thermal stability, enabling secure material removal rates while protecting the cutting edge. Process engineers and shop floor planners will find the product particularly useful where a single insert family is desired to cover multiple material groups, simplifying tooling inventories and streamlining setup changes. For application-specific cutting data, availability or to request tailored recommendations for Walter Tools Tiger·tec Gold inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — technical consultants are available to support process integration and optimisation. Technical data Article number: SNMX160640-F57-WSP45G-WALTER SKU: SNMX160640-F57-WSP45G-WALTER Product type: Fräswendeschneidplatte Designation: SNMX160640-F57 WSP45G Brand: Walter Tools Facts Plate size: 16 Plate thickness: 06 Corner radius: 4 Rake angle: 0° (negativ) Tolerance class: M Special features Series: Tiger·tec Gold Grade: WSP45G (coated carbide) Chipbreaker: F57 Plate shape: Quadrate 90° Execution: X Material suitability: Stahl; rostfreier Stahl; Superalloys/Titanium FAQ What materials is this insert suitable for? The SNMX160640-F57 WSP45G insert is specified for machining Stahl, rostfreier Stahl and superalloys/titanium, reflecting the P/M/S designation of the cutting grade. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold PVD coating on this insert improves wear resistance and thermal stability, allowing longer cutting cycles and more consistent edge life with Walter Tools quality control. What cutting tasks are best suited to the square 90° geometry? Square 90° inserts excel at face and shoulder milling where a robust cutting edge is required; the corner radius 4 adds strength for heavy engagement and interrupted cuts. Is the chipbreaker F57 suitable for finishing operations? The F57 chipbreaker is engineered for controlled chip flow during medium to heavy milling; it is most effective for roughing and semi-finishing where chip evacuation and edge protection are priorities. Does the negative 0° rake affect feed and cutting forces? A 0° (negativ) rake increases edge strength and is advantageous for stable cutting under high loads; it typically requires slightly higher cutting forces but improves resistance to chipping in demanding operations. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are cited solely for explanation. There is no affiliation between our company and the named brands. The offered article is an original factory-new product of the manufacturer Walter Tools.
SPEB090308-A67 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the combination of robust edge life, optimised chip control and thermal stability for reliable milling in demanding materials; order directly via Metav Werkzeuge or consult our specialists for process advice. SPEB090308-A67 WSM35G indexable milling insert — Tiger·tec Gold, square 90° (Walter Tools) The SPEB090308-A67 WSM35G is an indexable milling insert engineered for machining stainless steels and heat‑resistant superalloys, offering a balance of edge stability and wear resistance within the Tiger·tec Gold family. Tiger·tec Gold coating for high thermal stability Optimised chipformer A67 for secure chip control Square 90° form with 0.8 mm corner radius Suited to stainless steel and superalloys (M, S) Greater productivity through thermal stability and wear resistance The Tiger·tec Gold combination of a coated carbide substrate and modern multilayer coating provides enhanced thermal stability and wear resistance during heavy or interrupted cuts. This means more consistent tool life in applications with elevated cutting temperatures and tendencies to build up on the edge. The result is a reduction in unplanned tool changes and a steadier production rhythm when machining stainless steels and nickel‑based alloys, where heat and ductility strain the cutting edge. Reliable chip control and geometric advantages for safer machining Thanks to the designated A67 chipformer and the square 90° geometry, chip evacuation is more predictable and chips are broken into manageable segments, lowering the risk of re‑cutting and surface damage. The corner radius R0.8 mm and the relief angle 11° together promote a robust cutting edge that tolerates higher feed rates while maintaining acceptable surface finish. For workshops seeking repeatable results, this combination supports stable process windows and easier optimisation of cutting data. Purposeful grade selection for demanding materials The WSM35G grade is a coated carbide designed specifically for the M and S ISO groups: M denotes stainless steels, which require secure chip formation and chipping resistance; S covers heat‑resistant superalloys and titanium, demanding excellent edge stability and heat resistance. Selecting this grade reduces the compromise between tool life and component integrity, providing a predictable balance between wear performance and cutting reliability for difficult‑to‑machine alloys. Integration into machining processes and shopfloor benefits As a square insert with a compact thickness and standard size code, the insert integrates easily into conventional milling holders and indexable cutter systems, enabling quick index changes and minimal setup time. The tolerance class E and the execution B ensure consistent seating in the pocket and reproducible running behaviour, which simplifies process documentation and quality control. For production runs where downtime must be minimised, this insert supports higher availability and simplified tooling logistics. Contact Metav Werkzeuge today for tailored recommendations on cutting data and holder selection, or request assistance from our technical advisors to implement the SPEB090308-A67 WSM35G insert in production Technical data Article number: SPEB090308-A67-WSM35G-WALTER Designation: SPEB090308-A67 WSM35G Product type: indexable milling insert Series: Tiger·tec Gold Grade: WSM35G Chipformer: A67 Brand: Walter Tools Facts Shape: square 90° Corner radius: R0.8 mm Relief (free) angle: 11° Size code: 09 Thickness code: 03 Tolerance class: E Execution: B Special features Coated carbide (Tiger·tec Gold) Suitable for ISO groups M and S Optimised for stainless steel and superalloys Stable edge behaviour and reliable chip control Designed for productive milling applications FAQ What materials is this insert suitable for? The SPEB090308-A67 WSM35G insert is formulated for stainless steels (ISO group M) and heat‑resistant superalloys/titanium alloys (ISO group S). How does the Tiger·tec Gold coating benefit shopfloor performance? The Tiger·tec Gold coating on the WSM35G grade increases thermal stability and wear resistance, which extends effective tool life and supports higher cutting temperatures often encountered in machining stainless steels and superalloys. What does the A67 chipformer provide during milling? The A67 chipformer promotes consistent chip breaking and evacuation, reducing the likelihood of long, tangled chips and helping to protect the workpiece surface from recutting and damage. Is the square 90° geometry suitable for heavy interrupted cuts? The square 90° configuration combined with a 0.8 mm corner radius and a robust grade gives the insert good edge strength, making it suitable for a range of milling tasks including moderate interrupted cuts when mounted in appropriate tooling. Which machineholders are compatible with this insert? The SPEB090308-A67 WSM35G follows standard indexable insert dimensions and fits conventional milling cutter systems that accept a 09 size square insert; confirm holder compatibility and clamping standards before use. Walter Tools: Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and product names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is original, brand‑new manufacturer goods.
SPEB090308-A67 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger‑tec Gold coating, versatile P/M/S material capability and stable edge geometry for consistent, productive milling results; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. SPEB090308-A67 WSP45G – Tiger‑tec Gold square milling insert (P/M/S compatibility) by Walter Tools A SPEB090308-A67 WSP45G indexable milling insert engineered for versatile finishing and semi‑finishing of steel, stainless steel and heat‑resistant superalloys in general machining applications. Tiger‑tec Gold PVD coating Suitable for steel, stainless and superalloys Square 90° geometry, 0.8 mm nose radius 11° relief angle for secure cutting edge Longer tool life from Tiger‑tec Gold for continuous production The coated, PVD‑treated carbide grade delivers enhanced wear resistance and stable edge retention, which reduces the frequency of tool changes and supports uninterrupted machining cycles. The Tiger‑tec Gold technology combines a hard coating with a tough substrate, enabling dependable performance in runs with varying cutting conditions. For production planners this means fewer tool interventions and more predictable output: the result is a measurable increase in throughput and reduced downtime. The term PVD‑coated refers to a physical vapour deposition process that strengthens the cutting surface without sacrificing core toughness. Broad material coverage for mixed‑material shops Designed for the ISO material groups P/M/S, the insert is suitable for conventional unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys/titanium, providing flexibility across mixed production tasks. The WSP45G grade is tuned for secure chip formation in tougher materials, which lowers the risk of built‑up edge and promotes consistent surface finish. For machining engineers, the universality of the grade simplifies tooling lists and reduces inventory complexity while maintaining performance across diverse workpieces. Geometry and chip control that improve process reliability The square 90° plate form combined with a 0.8 mm nose radius gives a balance between strength and surface quality for semi‑finishing and finishing operations. The A67 chipbreaker is configured to control chip shape and evacuation, reducing recutting and improving tool life. With an 11° relief angle, the insert maintains a secure cutting edge and reduces rubbing on the flank face, which helps to conserve cutting forces and to stabilise tool‑holder behaviour during high engagement cuts. In practical terms, operators see fewer interruptions from poor chip control and more consistent component tolerances. Simple integration and predictable handling in tool setups The insert’s standard dimensions and tolerance class E make it straightforward to integrate into existing cutter bodies and to replicate setups across machines. Its designation and format adhere to common indexable insert conventions, so programming teams and machine operators can apply typical feeds and speeds while relying on the grade’s known performance envelope. Where application clarity is required, the insert’s A67 chipbreaker and square geometry provide clear benchmarks for cutting data optimisation, allowing process engineers to refine parameters with confidence. For reliable, high‑productivity milling using the Tiger‑tec Gold grade, contact Metav Werkzeuge for procurement or technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: SPEB090308-A67-WSP45G-WALTER Designation: SPEB090308-A67 ISO designation: SPEB090308-A67 WSP45G Manufacturer: Walter Tools Product type: Milling indexable insert Series: Tiger‑tec Gold Grade: WSP45G Core data Relief angle: 11° Corner radius: 0.8 mm Plate form: Square 90° Plate size: 09 Plate thickness: 03 Tolerance class: E Execution: B Features Chipbreaker: A67 Coating/technology: Tiger‑tec Gold (PVD) Material suitability: Steel (P), Stainless steel (M), Superalloys / Titanium (S) Typical applications: Finishing, semi‑finishing milling Design emphasis: Edge stability and chip control FAQ What materials can this insert machine effectively? The SPEB090308-A67 WSP45G insert is specified for the ISO groups P, M and S, meaning it machines steel, stainless steel and heat‑resistant superalloys/titanium with reliable chip formation and edge life. How does the Tiger‑tec Gold coating benefit production? Tiger‑tec Gold provides a hard, wear‑resistant surface while retaining substrate toughness; this combination improves the lifetime of the SPEB090308-A67 WSP45G and supports longer uninterrupted production runs. Which geometry aspects support good surface finish? The square 90° form together with a 0.8 mm nose radius and the A67 chipbreaker promote controlled cutting action and chip evacuation, helping to achieve consistent surface quality in finishing passes. Is this insert suitable for mixed‑batch workshops? Yes. The WSP45G grade and P/M/S suitability make the insert a versatile choice for mixed production environments, reducing the need for multiple specialised grades. How should chip control be adjusted for stainless steel? For stainless grades, prefer conservative feed rates and ensure sufficient coolant or appropriate cutting parameters; the A67 chipbreaker on this insert assists in forming short, manageable chips under these conditions. Manufacturer/Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is original, brand‑new goods from the manufacturer. The brand in this listing is Walter Tools.
SPEB120308-A67 WSP45G A67 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, a stable A67 chipbreaker and precision geometry to ensure consistent chip control and reproducible surface quality in mixed‑material production. Order the SPEB120308‑A67 WSP45G milling insert directly via Metav Werkzeuge or ask our consultants if needed. SPEB120308‑A67 WSP45G milling insert — square 90°, Tiger‑tec Gold (Walter Tools) A SPEB120308‑A67 WSP45G square milling insert designed for robust face and shoulder milling in steel, stainless steel and heat‑resistant alloys Tiger‑tec Gold PVD‑coated carbide Suitable for steel, stainless and superalloys Square 90° insert with 0.8 mm corner radius Chipbreaker A67 for stable chip control Consistent chip control for reliable milling cycles The combination of a dedicated A67 chipbreaker and the Tiger‑tec Gold coating delivers predictable chip formation and evacuation, which reduces interruptions and tool‑change frequency. The PVD‑coated carbide substrate maintains edge stability under intermittent cutting and elevated temperatures, so short cyclic stops for clearing stringy chips are less likely. This results in steadier cycle times and fewer rejects when machining demanding contours. Versatile material range reduces tooling complexity Designed for the ISO groups P / M / S, the grade supports machining of unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys/titanium. This single grade covers typical workshop mixes and lowers the number of inserts needed in the tool crib. The result is simplified inventory management and faster job changeovers while retaining process security and consistent surface quality. Precision geometry for reproducible part accuracy The square 90° format with a 0.8 mm corner radius and a 11° clearance angle gives predictable cutting engagement and robust corner strength for shoulder and slot milling. The manufacturing tolerance class E ensures interchangeability between inserts and holders, supporting repeatable clamping and dimensional accuracy across batches. The compact plate thickness and 12 format are optimised for stable seating and secure clamping in standard cutter bodies. Contact Metav Werkzeuge to discuss how the Walter Tools SPEB120308‑A67 WSP45G can streamline machining processes and to request tailored technical support Technical data Article number: SPEB120308-A67-WSP45G-WALTER Article designation: SPEB120308-A67 WSP45G Product type: milling insert Manufacturer: Walter Tools Facts Size: 12 Plate thickness: 03 Corner radius: 0.8 mm Free clearance angle: 11° Plate form: Square 90° Tolerance class: E Designs / Special features Series: Tiger‑tec Gold Grade: WSP45G (PVD coated carbide) Chipbreaker: A67 Material suitability: P / M / S (steel, stainless steel, superalloys/titanium) Execution: B FAQ Which materials can this insert machine reliably? The SPEB120308‑A67 WSP45G is formulated for ISO groups P, M and S, making it suitable for machining steel, stainless steel and heat‑resistant superalloys including titanium. What benefits does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold PVD coating on this Walter Tools insert improves wear resistance and thermal stability, leading to longer edge life and more consistent surface finishes under mixed cutting conditions. Is the insert suitable for finishing operations? With its 0.8 mm corner radius and tolerance class E, the insert supports reproducible dimensions and acceptable surface quality for many finishing passes, depending on holder rigidity and cutting parameters. Which chipbreaker is integrated and what advantage does it offer? The integrated A67 chipbreaker is optimised for controlled chip fragmentation and evacuation, reducing the risk of built‑up edge and stabilising the machining process in interrupted and continuous cuts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is original, factory‑new goods of the manufacturer (Walter Tools).
SPEB150408-A67 WSP45G A67 Wendeplatten - Walter Tools
High wear resistance from the Tiger·tec Gold coating, a stable cutting edge via the WSP45G grade and predictable chip control from the A67 chipbreaker combine to deliver efficient, repeatable milling results — order through Metav Werkzeuge or contact the consultants for application advice. SPEB150408-A67 WSP45G Fräswendeschneidplatte — Tiger·tec Gold PVD, square 90° by Walter Tools SPEB150408-A67 WSP45G is a high-performance milling insert designed for versatile milling applications across demanding materials Tiger·tec Gold PVD coating for long life Suitable for Stahl, rostfreier Stahl and high-temp alloys Square 90° form with 0.8 mm corner radius A67 chipbreaker for consistent chip control Durable coating that extends tool life and reduces downtime The Tiger·tec Gold coating applied to the WSP45G grade is a PVD-coated cemented carbide that prioritises wear resistance and edge stability. In practice this means longer intervals between indexings and fewer unexpected tool changes, which supports a more efficient production flow. The coating technology is optimised for milling and counteracts the thermal and mechanical loads typical for machining Stahl and rostfreier Stahl, so the end result is a more consistent surface finish and less rework in serial production. The combination of coating and grade enables higher process reliability and predictable tool behaviour under varying cutting conditions. Geometry and chip control that improve process stability A square 90° plate form with a 0.8 mm corner radius and an A67 chipbreaker produces controlled chips and a robust cutting edge suitable for many milling operations. The 11° clearance angle and tolerance class E contribute to repeatable seating and consistent engagement with the cutter body, helping to avoid chatter and reduce tool deflection in interrupted or heavy milling. These geometric choices favour stable cutting forces and simplified setup verification, so cycle times remain predictable and component tolerances are easier to maintain. Broad material suitability for demanding milling tasks The insert is specified for material groups P / M / S, which covers a wide production spectrum: P for unalloyed and alloyed Stahl, M for rostfreier Stahl, and S for heat-resistant superalloys and Titan-type materials. This breadth of applicability makes the insert a practical choice for job shops and production centres that handle mixed batches or require quick changeover between workpieces. The combination of a versatile grade and tailored chip control minimises the need for multiple tool inventories while supporting consistent surface quality across different alloys. For precise application advice or to secure genuine Walter Tools Tiger·tec Gold inserts, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations and order support Technical Data SKU: SPEB150408-A67-WSP45G-WALTER Product: Fräswendeschneidplatte SPEB150408-A67 WSP45G Manufacturer: Walter Tools Core specifications Plate size: 15 mm Corner radius: 0.8 mm Clearance angle: 11° Plate thickness: 04 Tolerance class: E Features & applications Grade: WSP45G Coating / series: Tiger·tec Gold Chipbreaker: A67 Material groups: P / M / S Plate form: Square 90° Execution: B FAQ Which materials is this insert suitable for? The SPEB150408-A67 WSP45G insert is specified for material groups P / M / S — suitable for machining Stahl, rostfreier Stahl and heat-resistant alloys such as superalloys and Titan-family materials. What are the advantages of the WSP45G grade? WSP45G is a PVD-coated carbide grade within the Tiger·tec Gold series that offers good wear resistance and a stable cutting edge for versatile milling applications, supporting consistent tool life across varying materials. How does the A67 chipbreaker affect performance? The A67 chipbreaker promotes stable chip formation and evacuation during milling, reducing the risk of built-up edge and improving surface quality while enabling reliable chip control in both continuous and interrupted cuts. Can this insert be used for finishing operations? With a 0.8 mm corner radius and square 90° geometry, the insert provides a balance between edge strength and finish capability; it is suitable for many semi-finish and finishing passes depending on machine rigidity and cutting parameters. What seating and tolerance features ensure repeatable mounting? The insert is supplied to tolerance class E with an 11° clearance angle, delivering predictable seating and repeatable engagement in compatible cutter bodies, which simplifies setup and inspection. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is an original, factory-new product of Walter Tools.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com