SNMX090408-F67 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of a Tiger·tec Gold coating and the WSM35G grade for stable cutting in demanding materials; the robust F67 chipbreaker and square 90° form ensure reliable chip control and long tool life. Order the SNMX090408-F67 WSM35G milling insert directly via Metav Werkzeuge or ask our consultants for application advice. SNMX090408-F67 WSM35G milling indexable insert – Walter Tools, Tiger·tec Gold, square 90°, negative geometry The SNMX090408-F67 WSM35G is a square 90° milling insert designed for productive machining of rostfreier Stahl and heat-resistant superalloys, combining a wear-resistant coating with a stable cutting edge for demanding milling operations. Tiger·tec Gold coating for heat resistance Designed for rostfreier Stahl and superalloys F67 chipbreaker for secure chip control Square 90° form with 0.8 mm corner radius High-performance grade and coating for consistent metal removal The insert’s WSM35G grade, part of the Tiger·tec Gold series, provides a coated carbide substrate tuned for high thermal and mechanical loads. This combination reduces flank wear and supports a stable cutting edge, which in turn lowers tool-change frequency and improves process reliability. For shops facing stainless and heat-resistant materials, the grade’s design promotes safer chip formation and helps avoid built-up edge—translating into more predictable component quality and fewer interruptions in production. Geometry and chip control engineered for industrial milling The square 90° shape with a corner radius of 0.8 mm delivers a balance between edge strength and surface quality for shoulder and face milling. The F67 chipbreaker is optimised to break and evacuate chips efficiently during interrupted cuts and heavy engagement passes, reducing recutting and heat concentration. The insert’s 0° (negative) clearance provides a positive influence on cutting forces and stability, making it particularly suitable where rigidity and repeatability are required. Application guidance and machining benefits Specifically developed for difficult-to-machine alloys, the insert is recommended for operations involving rostfreier Stahl and nickel‑based superalloys where heat resistance and edge stability are paramount. The coated carbide composition and chip former reduce thermal load on the cutting edge, extending insert life and maintaining surface finish consistency. When selecting cutting data, lean towards conservative feed and incremental increases in speed to establish optimum parameters for the workpiece and machine rigidity. Contact Metav Werkzeuge for tailored recommendations on fixtures, cutting data and availability of SNMX090408-F67 WSM35G; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for direct consultation Technical Data SKU: SNMX090408-F67-WSM35G-WALTER Article designation: SNMX090408-F67 WSM35G Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WSM35G Core data Insert size: 09 Thickness: 04 Corner radius: 0.8 mm Clearance angle: 0° (negative) Insert form: Square 90° Chipbreaker: F67 Tolerance class: M Special features Coating: Tiger·tec Gold Material: coated carbide Suitable for rostfreier Stahl and heat‑resistant superalloys Geometry: square insert for shoulder and face milling Designed for stable chip formation and robust cutting edge FAQ Which materials are best processed with this insert? The SNMX090408-F67 WSM35G insert is suitable for machining rostfreier Stahl and heat‑resistant superalloys; its Tiger·tec Gold coating and WSM35G grade support secure chip formation in these materials. What does the F67 chipbreaker achieve in milling operations? The F67 chipbreaker on the SNMX090408-F67 promotes reliable chip control and evacuation, reducing recutting and improving surface quality during heavy or interrupted cuts. How does the 0° (negative) clearance affect cutting performance? Negative clearance increases edge strength and process stability; with the SNMX090408-F67 this geometry helps maintain repeatable cutting forces and supports high‑pressure engagements. Is the insert suitable for shoulder milling and face milling? Yes. The square 90° form and 0.8 mm corner radius provide the edge strength needed for shoulder and face milling while delivering consistent surface finish. Which coating advantages does Tiger·tec Gold provide? Tiger·tec Gold on the SNMX090408-F67 offers enhanced heat resistance and reduced wear, which contributes to longer tool life and steadier machining of demanding alloys. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX090408-F67 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger·tec Gold PVD-coated grade, proven suitability for steel, stainless steels and superalloys, and a stable negative rake to maintain consistent production cycles; order directly via Metav Werkzeuge or consult our technical team for application guidance. SNMX090408-F67 WSP45G indexable milling insert – square 90°, Tiger·tec Gold, Walter Tools SNMX090408-F67 WSP45G is an indexable milling insert designed for robust slotting and face milling in demanding materials, combining a Tiger·tec Gold PVD-coated carbide grade with a secure cutting geometry for industrial machining. Tiger·tec Gold PVD-coated carbide Suitable for steel, stainless and superalloys 0° negative rake for stable cutting Square 90° form with 0.8 mm corner radius Consistent machining performance for reliable output The Tiger·tec Gold PVD-coated grade delivers a balance of edge stability and thermal resistance that supports repeatable machining results. Thanks to the WSP45G grade, the insert sustains stable chip formation under typical milling loads in alloyed workpieces. This reduces unplanned stops and supports predictable tool life, which in turn contributes to improved process throughput and lower overall machining variation. Versatile material range reduces tool changes Designed for use with steel, stainless steels and superalloys/titanium, the insert’s substrate and coating chemistry enable reliable performance across material groups that differ in heat conduction and toughness. The result is a single insert option that lowers the need for frequent tool changes between operations, promoting workflow efficiency and less inventory complexity in production environments. Geometry engineered for secure cutting and surface quality The 0° negative rake and square 90° profile provide a robust cutting edge that resists deformation under heavy milling forces. Combined with a 0.8 mm corner radius, this geometry helps maintain edge strength while balancing allowable feed and surface finish. Operators benefit from predictable burr formation and fewer edge failures when heavy engagement and intermittent cuts occur. Practical procurement and application support Supplied in Walter Tools’ Tiger·tec Gold series and manufactured to tolerance class M, the insert is suitable for standard milling toolholders accepting SNMX-style plates. The clear specification of grade, breaker and form simplifies the selection process for production engineers. For detailed cutting data or to match the insert with a specific holder, Metav Werkzeuge can provide the relevant application tables and recommendations. Contact Metav Werkzeuge for tailored application advice on the SNMX090408-F67 WSP45G, request cutting parameters or order technical documentation via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: SNMX090408-F67-WSP45G-WALTER Designation: SNMX090408-F67 WSP45G Brand: Walter Tools Product type: Milling indexable insert Series: Tiger·tec Gold Grade: WSP45G Facts Corner radius: 0.8 mm Thickness: 4.0 mm Shape: Square 90° Relief angle: 0° (negative) Breaker: F67 Plate size: 09 Tolerance class: M Special features Substrate/coating: PVD-coated carbide (Tiger·tec Gold) Material suitability: steel (P), stainless steels (M), superalloys and titanium (S) Execution: X Ideal for milling applications with secure chip control FAQ What materials can this insert machine effectively? The SNMX090408-F67 WSP45G insert from Walter Tools is specified for machining steel, stainless steels and superalloys/titanium, offering a versatile solution for mixed-production environments. What does the 0° negative rake mean for cutting? A 0° negative rake on the SNMX090408-F67 WSP45G increases edge strength and resistance to chipping under heavy loads, improving stability during interrupted cuts and roughing operations. How does the Tiger·tec Gold coating benefit tool life? The Tiger·tec Gold PVD coating on the WSP45G grade enhances wear resistance and thermal stability, which supports longer edge life and consistent performance across a range of cutting conditions. Which milling operations suit this insert form? The square 90° form with a 0.8 mm corner radius is suitable for face milling and slotting where a robust corner is required; the profile helps maintain surface integrity during higher engagement milling. What does tolerance class M indicate? Tolerance class M signifies medium dimensional tolerances appropriate for general industrial milling inserts, balancing precision and cost for standardised toolholder systems. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanation. There is no affiliation between our company and the named brands. The offered article is original factory-new goods of the manufacturer.
SNMX0904ANN-F27 WKP35G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating with the WKP35G grade ensures prolonged tool life and consistent chip control in demanding milling tasks; the square 90° format and 0° negative rake deliver mechanical stability for interrupted cuts. Order the SNMX0904ANN-F27 WKP35G insert directly via Metav Werkzeuge or ask our consultants if needed. SNMX0904ANN-F27 WKP35G — Indexable milling insert, Tiger·tec Gold (Walter Tools) SNMX0904ANN-F27 WKP35G is a square indexable insert designed for high-performance milling in steel and cast iron applications Tiger·tec Gold coating for long life Optimised chipbreaker F27 for controlled chips Square 90° geometry for sturdy milling Suitable for steel (P) and cast iron (K) Extended life through advanced coating and grade The combination of Tiger·tec Gold coating and the WKP35G coated-carbide grade provides a clear advantage where tool life and consistency are decisive. The multilayer coating reduces flank and crater wear, resulting in less frequent index changes and stable cutting edge performance. For process planners, this translates into higher machine uptime and lower tooling costs per finished part. The coated-carbide chemistry is optimised for thermal and abrasive loads typical of machining steel and cast iron, supporting longer tool cycles without sacrificing surface quality. Predictable chip control for reliable production Equipped with the F27 chipbreaker, this insert improves chip formation and evacuation during milling. Consistent chip segmentation lowers the risk of chip entanglement and reduces secondary operations for chip removal. The 0° negative rake and the square 90° geometry contribute to mechanical rigidity, making the configuration especially suitable for heavy cuts and interrupted operations. As a result, shops see fewer process interruptions and a steadier surface finish, helping to meet tight tolerances with predictable cycle times. Robust geometry and tolerance for machinist confidence The SNMX0904ANN-F27 WKP35G insert is manufactured to tolerance class M and a compact plate size 09 with thickness 04, ensuring repeatable seating and stable clamping in standard indexable cutter bodies. The negative rake and square form deliver a strong cutting edge that resists chipping under shock loads. This design focus supports productive milling strategies where component integrity and dimensional stability are priority criteria. For engineering teams seeking dependable milling performance, this insert offers a balanced mix of durability and process security. For application-specific advice on Walter Tools Tiger·tec Gold inserts or to confirm suitability for a machining task, contact Metav Werkzeuge for detailed consultation and availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: SNMX0904ANN-F27-WKP35G-WALTER Designation: SNMX0904ANN-F27 WKP35G Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WKP35G Facts Insert size: 09 Thickness: 04 Corner angle: 90° Free angle: 0° (negative) Tolerance class: M Chipbreaker: F27 Plate form: Square 90° Special features Coating technology: Tiger·tec Gold Material: Coated carbide (WKP35G) Suitable for: steel (P) and cast iron (K) Execution: X Series description: Optimised for stable chip formation and productive machining FAQ What materials is this insert designed to machine? The SNMX0904ANN-F27 WKP35G insert is specified for steel (P) and cast iron (K) machining, reflecting the WKP35G grade and Tiger·tec Gold coating suitability. Which chipbreaker does the insert use and why does it matter? This insert features the F27 chipbreaker, which promotes controlled chip formation and evacuation, improving machining stability and reducing the likelihood of chip-related interruptions when milling steel and cast iron. How does the insert geometry support interrupted cuts? The square 90° geometry combined with a 0° negative rake provides increased edge strength and rigidity, making the insert well suited to interrupted milling where edge resilience is needed. What tolerance and size can be expected from this insert? The insert is produced to tolerance class M, with size 09 and thickness 04, ensuring repeatable seating and consistent positioning in standard indexable milling cutters. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
SNMX0904ANN-F57 WKK25G WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, a square 90° geometry and targeted optimisation for cast iron to maintain productive, repeatable milling operations; order the SNMX0904ANN-F57 WKK25G milling insert directly via Metav Werkzeuge or ask our consultants if needed. SNMX0904ANN-F57 WKK25G — milling insert, Tiger·tec Gold, for cast iron (Walter Tools) A SNMX0904ANN-F57 WKK25G milling insert engineered for productive machining of cast-iron components using Tiger·tec Gold coating technology Tiger·tec Gold coating for wear resistance Optimised for cast iron machining Square 90° insert geometry 0° negative rake for robust cutting Boosted productivity when machining cast iron The combination of the Tiger·tec Gold technology and the grade WKK25G delivers markedly improved wear resistance and consistent edge life when working with abrasive cast-iron materials. The coated cemented-carbide formulation is designed to manage the short, breaking chips typical of cast iron, which reduces unexpected tool changes and supports longer uninterrupted cutting cycles. These characteristics contribute to measurable cycle-time stability and cost-efficiency in serial production and high-volume milling tasks. Geometry made for stability and reliable chip control A square 90° geometry paired with a 0° negative rake offers a robust cutting edge that tolerates intermittent cuts and varying depths of cut without sacrificing surface integrity. The insert’s F57 chipbreaker is optimised to form and evacuate chips reliably in brittle materials, lowering the risk of built-up edge and improving process security. This structural robustness translates into fewer machine stops for maintenance and simpler tool management on mixed-job shop floors. Consistent results for production environments Selected for its balanced performance profile, the WKK25G grade is a practical choice where repeatability and predictable tool life are priorities. The insert’s specification supports stable cutting forces and good surface finish in cast-iron applications, enabling predictable planning of tool replacement intervals. Together with Walter Tools’ manufacturing standards, the component is suited for shops seeking a dependable, industrial-grade solution that integrates easily into existing toolsets. Discuss Walter Tools Tiger·tec Gold inserts with Metav Werkzeuge to optimise cast-iron milling processes — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical advice and order support Technical data Article number: SNMX0904ANN-F57-WKK25G-WALTER Designation: SNMX0904ANN-F57 WKK25G Product type: Milling insert Manufacturer: Walter Tools Series: Tiger·tec Gold Numbers / Core data Size: 09 Thickness: 04 Relief angle: 0° (negativ) Shape: Quadrat 90° Chipbreaker: F57 Tolerance class: M Execution: X Material code: K Designs / Special features Grade: WKK25G (coated cemented carbide) Application: Cast iron (ISO group K) Series characteristics: Tiger·tec Gold coating technology Chip control optimised for short, breaking chips FAQ What materials is this insert suited for? The SNMX0904ANN-F57 WKK25G milling insert (Walter Tools) is optimised for cast iron (ISO group K) and performs well where abrasive wear and short, breaking chips occur. How does the Tiger·tec Gold technology help in production? Tiger·tec Gold coating on the WKK25G grade enhances wear resistance and edge stability, which supports longer tool life and more consistent machining results in production environments. What is the benefit of the square 90° geometry? The square 90° geometry provides a strong cutting edge and dimensional stability, enabling robust milling operations and repeatable results with the SNMX0904ANN-F57 WKK25G insert. Which chipbreaker is fitted and why does it matter? The fitted chipbreaker is F57, optimised to form and evacuate short, brittle chips typical of cast-iron machining, improving chip control and reducing the risk of built-up edge. Can this insert be used for finishing operations? While primarily designed for productive cast-iron machining, the insert’s stable cutting edge and Tiger·tec Gold performance can deliver acceptable surface quality where process parameters are set accordingly for finishing passes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX0904ANN-F57 WKP35G Wendeplatten - Walter Tools
Combining Tiger·tec Gold coating with the WKP35G grade and a 0° negative rake, the insert delivers robust wear resistance and dependable chip control for machining Stahl and Gusseisen; order directly via Metav Werkzeuge or consult our specialists for process optimisation. SNMX0904ANN-F57 WKP35G milling indexable insert — square 90° format, 0° negative rake, Walter Tools The SNMX0904ANN-F57 WKP35G is a square 90° milling insert engineered for productive machining of Stahl and Gusseisen, featuring Tiger·tec Gold coating for extended tool life. Tiger·tec Gold coating for high wear resistance WKP35G grade for stable chip formation Square 90° geometry for versatile milling 0° negative rake for secure edge strength High wear resistance that keeps production running The combination of the Tiger·tec Gold coating and the WKP35G carbide grade provides a clear advantage where abrasion and edge wear limit cycle times. Designed as a coated carbide cutting edge, the insert resists the thermal and mechanical stresses typical when machining Stahl and Gusseisen, which reduces flank wear and the need for frequent index changes. This results in longer uninterrupted runs and a more predictable tool-change schedule, supporting higher overall equipment effectiveness in serial production environments. Geometry and edge design for reliable chip control A square 90° format with a 0° negative rake offers enhanced edge strength and stability, particularly under interrupted cuts or mixed-material components. The integrated F57 chipbreaker pattern promotes controlled chip fragmentation when working with the P and K groups, so chips evacuate efficiently and surface finish is maintained without additional manual intervention. The insert’s tolerance class M ensures consistent seating and repeatable results across toolholders, simplifying inventory management and setup routines. Practical machining benefits and process guidance The insert’s specification supports operations that demand both productivity and robustness: milling shoulders, face milling and moderate roughing passes in Stahl and Gusseisen. The coating and grade selection are optimised for common industrial conditions, balancing wear resistance with edge toughness. For unfamiliar applications, consider conservative cutting data initially and increase speeds incrementally while monitoring tool wear and chip shape; the combination of Tiger·tec Gold and the WKP35G grade generally yields stable performance under such tuned conditions. Discuss machining parameters and availability for the SNMX0904ANN-F57 WKP35G with Metav Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 — technical advisors ready to recommend the best process settings Technical data Article number: SNMX0904ANN-F57-WKP35G-WALTER Designation: SNMX0904ANN-F57 WKP35G Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Insert shape: Square 90° Insert size: 09 Thickness: 04 Free rake angle: 0° (negative) Chipbreaker: F57 Tolerance class: M Material group: P / K Special features Coating: Tiger·tec Gold Grade: WKP35G (coated carbide) Application: Stahl and Gusseisen Execution: X (standard geometry) FAQ What materials is this insert suitable for? The SNMX0904ANN-F57 WKP35G by Walter Tools is specified for machining Stahl (P) and Gusseisen (K) according to the grade and coating characteristics. How does the Tiger·tec Gold coating benefit wear life? Tiger·tec Gold on the WKP35G grade enhances abrasive wear resistance and thermal stability on the insert, extending service life during demanding milling of Stahl and Gusseisen. What cutter geometry is represented by SNMX0904ANN-F57? The designation denotes a square 90° insert with a specific chipbreaker (F57) and a 0° negative rake, optimised for robust edge strength and consistent chip control. Is the insert suitable for interrupted cuts? Yes, the 0° negative rake and the WKP35G grade provide increased edge toughness, making the insert well suited to interrupted milling conditions commonly encountered in industry. How does tolerance class M affect toolholding? Tolerance class M delivers consistent seating accuracy and repeatable positioning in standard toolholders, which supports predictable machining results and easier tool setup. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Mention of Walter Tools is for informational purposes only. The offered article is an original, factory-new product of the manufacturer.
SNMX0904ANN-F57 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the proven Tiger·tec Gold coating and the robust chip control of the WSM35G grade for dependable machining of stainless steels and heat‑resistant alloys; combine long tool life, stable cutting edges and consistent chip evacuation for a reliable milling process. Order directly via Metav Werkzeuge or consult the technical team for application advice. SNMX0904ANN-F57 WSM35G indexable milling insert — square 90°, Tiger·tec Gold, Walter Tools The SNMX0904ANN-F57 WSM35G is an indexable milling insert engineered for high‑performance machining of stainless steels and heat‑resistant superalloys, offering a square 90° form with a negative rake for demanding operations Tiger·tec Gold coated for extended tool life Optimised chip control with F57 breaker Square 90° geometry for stable milling Suitable for stainless and heat‑resistant alloys Durable coating and predictable wear for continuous production The combination of the Tiger·tec Gold coating and the WSM35G cutting grade delivers a balance of heat resistance and edge stability that is essential when machining stainless steels and nickel‑based alloys. The coated carbide construction supports steady wear behaviour under thermal and mechanical stress, reducing the risk of unexpected tool failure. This reliability translates into fewer tool changes and a more consistent process window, which helps maintain productivity in batch and serial machining. The coating also improves resistance against built‑up edge and flank wear, so surface finish and dimensional consistency remain predictable over longer tool lives. Stable chip formation and reduced machining interruptions Equipped with the F57 chipbreaker, the insert promotes controlled chip fragmentation and evacuation during milling of tough materials. Effective chip control lowers the chance of entanglement and improves coolant access to the cutting zone, which in turn helps preserve the cutting edge. For machining centres and production cells where uninterrupted cycles are critical, the enhanced chip management contributes to shorter cycle times and reduced manual intervention. The insert’s design supports efficient swarf flow without sacrificing cutting stability, which benefits both roughing and profile milling operations. Robust geometry for secure cutting and part quality The square 90° plate shape with a 0° negative rake provides a strong cutting edge and resistance to mechanical shock during interrupted cuts or when encountering hard inclusions. This geometry is particularly advantageous in heavy milling where edge strength and stiffness are priorities. The negative rake angle helps distribute cutting forces and lowers the risk of chipping, while the square form offers four usable cutting edges, improving economy per insert. As a result, component tolerances and surface integrity remain consistent even under demanding conditions. Application guidance and material suitability The WSM35G grade is tailored for ISO groups M and S, meaning it is suitable for stainless steels and heat‑resistant superalloys and titanium respectively. When selecting cutting parameters, prioritise moderate feed rates and appropriate coolant strategy to exploit the grade’s heat resistance and to maintain stable chip formation. For shops seeking to adapt the insert to existing toolholders, the designation SNMX0904ANN‑F57 indicates the plate form and chipbreaker combination; matching the insert to the correct cutter body ensures optimum clamp and run‑out characteristics. For customised advice on parameter windows and holder compatibility, technical consultation is available to support process optimisation. Discuss Walter Tools Tiger·tec Gold inserts with Metav Werkzeuge for tailored machining solutions — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: SNMX0904ANN-F57-WSM35G-WALTER Designation: SNMX0904ANN-F57 WSM35G Product type: Fräswendeschneidplatte (indexable milling insert) Brand: Walter Tools Core specifications Plate form: Quadrat 90° Plate size: 09 Plate thickness: 04 Breaker: F57 Free cutting angle: 0° (negative) Tolerance class: M Grade/series: WSM35G / Tiger·tec Gold Execution: X Special features Coating / grade: Tiger·tec Gold (coated carbides) Material suitability: S / M Applicable for: rostfreier Stahl (ISO group M) Typical application: Heavy and difficult‑to‑cut materials, depending on geometry Insert family: SNMX series FAQ What materials is the SNMX0904ANN‑F57 WSM35G suited for? The SNMX0904ANN‑F57 WSM35G from Walter Tools is specified for ISO groups M and S, making it suitable for stainless steels and heat‑resistant superalloys or titanium depending on the cutter geometry. How does the F57 chipbreaker affect machining performance? The F57 chipbreaker promotes controlled chip formation and evacuation, improving swarf management during milling with the SNMX0904ANN‑F57 WSM35G and helping to maintain edge life and surface quality. Is the square 90° geometry beneficial for interrupted cuts? Yes, the square 90° plate with a negative rake provides a robust cutting edge that is resistant to chipping, which supports secure performance in interrupted and heavy milling operations with the SNMX0904ANN‑F57 WSM35G. How many cutting edges are available per insert and what is the implication? The square plate form offers multiple usable cutting edges; this increases economy per insert and, when combined with the Tiger·tec Gold coating, extends effective tool life for the SNMX0904ANN‑F57 WSM35G. Can the SNMX0904ANN‑F57 WSM35G be used in existing cutter bodies? Compatibility depends on the cutter’s insert pocket and clamping system; the SNMX0904ANN‑F57 designation indicates the form and size, so matching the insert to the proper cutter body is recommended to ensure correct clamping and run‑out. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only and do not indicate any affiliation with our company. The offered article is an original, factory‑new product of the manufacturer Walter Tools.
SNMX0904ANN-F57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating, versatile WSP45G grade and robust square 90° geometry for reliable milling performance; order this insert directly via Metav Werkzeuge or ask our consultants for application support. SNMX0904ANN-F57 WSP45G Milling Insert — Square 90°, 0° Negative Rake (Walter Tools) The SNMX0904ANN-F57 WSP45G is a square 90° milling insert engineered for secure, versatile milling on steel, stainless steel and heat-resistant alloys, suitable for productive roughing and finishing tasks. Tiger·tec Gold PVD coating for long life Suitable for steel, stainless and superalloys Square 90° geometry for stable milling 0° negative rake for secure cutting High-process security from the Tiger·tec Gold grade The SNMX0904ANN-F57 WSP45G combines the Tiger·tec Gold PVD coating with a WSP45G substrate to deliver consistent, wear-resistant performance. The coated carbide composition supports stable cutting edges and extended tool life under the thermal loads typical of milling steel and stainless steels. The designation P/M/S indicates suitability for steel, stainless steel and superalloys/titanium, so the grade is intentionally versatile: it manages typical heat and chip‑formation behaviours for these groups while reducing flank wear. This reliability translates into fewer index changes and steadier production cycles. Geometry designed for rigidity and repeatable results The square 90° insert form with 0° negative rake offers a robust geometry that resists edge chipping in interrupted cuts and heavy engagement. A zero-degree relief produces a more positive support under the cutting edge, improving edge stability when machining tough materials. The chipformer F57 is tuned to promote controlled chip flow, which supports safer evacuation and reduces the risk of built-up edge on stainless steels. Together, these elements improve process security and contribute to consistent surface quality and dimensional control. Clear process guidance for material compatibility Rated with tolerance class M, this insert provides a consistent seat and fit in indexable tooling where medium tolerance stability is required. The WSP45G grade’s balanced properties make it suitable for operations that demand both tool life and surface finish, such as semi-finishing and mixed rough/finish passes. When machining stainless grades or heat-resistant alloys, the combination of coating and carbide substrate helps to maintain a stable cutting edge despite higher cutting temperatures and tougher chip behaviour, leading to predictable cycle times and lower scrap rates. Practical handling and economic benefits for production As an indexable milling insert, this SNMX0904ANN-F57 style component allows multiple edges to be used before regrinding or replacement, supporting efficient spare-part management and reduced tooling costs per component. The standardised square 90° shape enables straightforward integration in holders designed for SNMX09-type plates and simplifies tool setup. The coated carbide construction offers a compromise between toughness and wear resistance, so fewer tool changes are required and machine uptime is improved. These operational advantages help to increase throughput and reduce process interruptions. For high process security with Tiger·tec Gold, contact Metav Werkzeuge for matching toolholder recommendations and application support: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: SNMX0904ANN-F57-WSP45G-WALTER Article designation: SNMX0904ANN-F57 WSP45G Product type: Milling insert (Fräswendeschneidplatte) Brand: Walter Tools Series: Tiger·tec Gold Facts Insert size: 09 Plate thickness: 04 Geometry: Square 90° Relief angle: 0° (negative) Chipbreaker: F57 Tolerance class: M Materials & features Coating / grade: WSP45G (PVD Tiger·tec Gold) Applicable materials: Steel (P), Stainless steel (M), Superalloys / Titanium (S) Base material: coated carbide Execution: X Plate form / ISO designation: SNMX0904ANN-F57 WSP45G FAQ What materials is this milling insert suitable for? The SNMX0904ANN-F57 WSP45G is suitable for machining steel, stainless steel and heat-resistant superalloys/titanium (material groups P, M, S) thanks to its Tiger·tec Gold coating and adapted carbide substrate. What does the WSP45G grade offer compared with conventional grades? WSP45G is a Walter PVD-coated grade from the Tiger·tec Gold family that emphasises a balance of toughness and wear resistance, providing good edge stability and extended tool life in mixed milling applications. When is the 0° negative rake geometry preferable? A 0° negative rake is preferable for applications requiring robust edges and secure cutting, such as interrupted cuts, heavy engagement milling or when machining tough alloys where edge chipping must be avoided. How does the chipbreaker F57 affect machining? The F57 chipformer promotes controlled chip formation and evacuation, reducing the chance of built-up edge and improving surface finish, especially on materials prone to stringy or sticky chips like some stainless steels. Is this insert suitable for finishing operations? Yes, the insert’s coating and grade combination supports both semi-finishing and finishing passes; the square 90° geometry and tolerance class M offer a repeatable seating and stable finish when cutting parameters are optimised. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only; there is no affiliation between our company and the named manufacturers. The offered item is an original, factory-new product of the stated manufacturer.
SNMX0904ANN-F67 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and a robust F67 chipbreaker to achieve stable cutting edges and reliable chip control during heavy-duty machining of stainless steel and heat-resistant alloys; order the SNMX0904ANN-F67 WSM35G milling indexable insert directly via Metav Werkzeuge or consult our team for application advice. SNMX0904ANN-F67 WSM35G milling indexable insert — Tiger·tec Gold coating, F67 chipbreaker (Walter Tools) SNMX0904ANN-F67 WSM35G is a square 90° milling indexable insert designed for demanding applications in stainless steel and high-temperature alloys Tiger·tec Gold coating WSM35G For stainless steel and superalloys Square 90° insert, 0° negative rake Stable chip control with F67 breaker Consistent performance on challenging materials The Tiger·tec Gold grade WSM35G is a coated carbide specifically engineered for machining tough-to-cut materials such as stainless steel and heat-resistant superalloys. The coating and substrate combination promotes stable cutting-edge behaviour under high thermal and mechanical load, reducing the risk of built-up edge and premature flank wear. In practice this translates into fewer tool changes and more predictable component quality during medium-to-heavy cutting operations, while the material designation S / M signals suitability across superalloys and stainless steels as defined by ISO 513. Robust geometry and controlled chip formation A square geometry with a 90° cutting corner and a 0° negative rake provides a mechanically strong cutting edge, ideal for interrupted cuts and heavy engagement. The integrated F67 chipbreaker supports reliable chip control across variable feeds, forming compact chips that evacuate efficiently from the cutter body. This combination improves process stability and allows consistent surface quality even in long production runs. Negative rake designs like this absorb shock better and preserve edge integrity, making the insert a practical choice where mechanical robustness is prioritised. Production-ready reliability and economical machining Built to deliver repeatable results, the insert benefits from Walter Tools’ focus on durable grades and optimised chip formers. The design promotes a balanced trade-off between wear resistance and edge toughness, contributing to extended tool life and reduced machining costs per part in series production. Integration into existing tooling systems is straightforward when the correct SNMX toolholder is used; the result is less downtime and more throughput. Where process security and surface consistency matter, this solution supports a dependable manufacturing flow backed by a recognised tooling brand. For machining stainless steel and high-temperature alloys with confidence, contact Metav Werkzeuge for a tailored recommendation and procurement: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: SNMX0904ANN-F67-WSM35G-WALTER Name: Fräswendeschneidplatte SNMX0904ANN-F67 WSM35G Walter Tools Manufacturer: Walter Tools Facts Series: Tiger·tec Gold Grade: WSM35G Chipbreaker: F67 Shape: Square 90° Size: 09 Thickness: 04 Rake angle: 0° (negative) Tolerance class: M Material designation: S / M Special features Coated carbide (Tiger·tec Gold) Optimised for stainless steel and superalloys/titanium Robust cutting edge for interrupted and heavy cuts Reliable chip control with F67 chipbreaker Walter Tools quality and application focus FAQ What materials is this insert suitable for? The SNMX0904ANN-F67 WSM35G insert is intended for stainless steel and heat-resistant superalloys (designations M and S), supporting stable machining of tough, heat-generating materials. What advantage does the 0° negative rake offer? A 0° negative rake increases edge strength and resistance to mechanical shock; the SNMX0904ANN-F67 WSM35G therefore performs well in interrupted cuts and heavy engagement conditions. How does the F67 chipbreaker improve production? The F67 chipbreaker on this insert produces compact, controllable chips, enhancing evacuation from the cutter and reducing the likelihood of chip-related workpiece marks during continuous machining runs. Is the insert coated and what does that mean for tool life? Yes; the SNMX0904ANN-F67 WSM35G uses the Tiger·tec Gold coating technology on a coated carbide substrate, which improves wear resistance under thermal stress and supports longer cutting intervals. Which cutter geometry is represented by the designation SNMX0904ANN-F67? The designation indicates a square 90° insert with size 09 and thickness 04, equipped with the F67 chipbreaker and a negative 0° rake suitable for robust milling operations. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The offered article is an original, factory-new product of the manufacturer Walter Tools.
SNMX0904ZNN-F57 WKK25G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold wear protection, the robust WKK25G grade and a square 90° geometry for reliable cast‑iron milling performance; order the SNMX0904ZNN-F57 WKK25G milling insert directly via Metav Werkzeuge or consult the technical team for process parameters. SNMX0904ZNN-F57 WKK25G – Milling indexable insert, Tiger‑tec Gold for cast iron (Walter Tools) The SNMX0904ZNN-F57 WKK25G is a square 90° milling insert developed for productive machining of cast iron components, combining a coated carbide grade with a chipbreaker tuned to short, controlled chips. Tiger‑tec Gold coated for abrasion resistance Optimised for cast iron (ISO K) Square 90° geometry for robust cutting 0° negative rake for stable machining High-efficiency cast‑iron machining The SNMX0904ZNN-F57 WKK25G is designed to deliver consistent tool life and predictable wear behaviour when machining abrasively acting cast‑iron grades. The Tiger‑tec Gold coating, applied to a coated carbide substrate, provides enhanced abrasion resistance and thermal stability; this reduces flank wear and supports longer operating intervals between indexings. For production environments where repeatability and process stability are decisive, the combination of a coated grade and a square, 90° geometry ensures secure cutting forces and simple tool path planning, which contributes to improved cycle times and part throughput. Consistent chip control and cutting stability Chip management and edge security are central to efficient milling of brittle materials. The integrated chipbreaker F57 is configured to produce short, readily broken chips that evacuate easily from the-cut, reducing the risk of built‑up edge and workpiece damage. The negative 0° rake promotes a stiff cutting edge and reduces the tendency for vibration in interrupted cuts, while the square 90° form gives a robust cutting corner for heavier engagement. Together, these features enable stable roughing and semi‑finishing operations with an emphasis on dimensional control and surface consistency. Application guidance and measurable benefits Key dimensional values such as insert size 09 and thickness 04 define the mechanical interfaces and clamping stability; the tolerance class M reflects machining precision suitable for standard production requirements. The WKK25G grade, optimised for material group K (cast iron) under ISO 513, is intended for abrasive, short‑chip conditions typical of these alloys and is therefore well suited to both general‑purpose and focused cast‑iron strategies. Process planners will find the insert supports predictable wear curves, facilitating tool‑change scheduling and lowering total machining costs per part while maintaining surface quality. For reliable cast‑iron productivity and technical advice on implementing Tiger‑tec Gold inserts, contact Metav Werkzeuge – our consultants will assist with cutting data and availability to match the SNMX0904ZNN-F57 WKK25G to specific applications Technical Data Article number/SKU: SNMX0904ZNN-F57-WKK25G-WALTER Designation: SNMX0904ZNN-F57 WKK25G Brand: Walter Tools Series: Tiger‑tec Gold Facts Size: 09 Thickness: 04 Relief angle: 0° (negative) Geometry: Square 90° Tolerance class: M Special features Grade: WKK25G (coated carbide) Chipbreaker: F57 Material group: K (cast iron) Execution: X Suitable for ISO K materials FAQ What materials is this insert intended for? The SNMX0904ZNN-F57 WKK25G is developed for cast iron machining and corresponds to ISO material group K, offering abrasion‑resistant performance for typical cast‑iron applications. How does the Tiger‑tec Gold coating benefit machining? The Tiger‑tec Gold coating on the WKK25G grade improves abrasion resistance and thermal stability, which in turn enhances tool life and keeps flank wear predictable under continuous cast‑iron cutting. What is the effect of the chipbreaker F57? The chipbreaker F57 produces short, controllable chips suitable for brittle materials; this supports efficient chip evacuation and reduces the risk of surface damage or tool‑clogging during interrupted cuts. Is the insert suitable for heavy machining or finishing? The square 90° geometry and 0° negative rake provide a strong cutting edge for heavier engagement; the insert is appropriate for roughing and semi‑finishing in cast iron where rigidity and edge security are required. Which size and clamping considerations apply? This product is offered in size 09 with thickness 04 and tolerance class M; ensure the toolholder is specified for SNMX0904ZNN‑style inserts and that clamping conforms to the holder manufacturer's instructions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Mention of brand names is for explanatory purposes only; no connection between our company and the brands is implied. The offered item is an original, factory‑new product of the manufacturer.
SNMX0904ZNN-F57 WKP25S Wendeplatten - Walter Tools
Efficient, coated carbide insert combining Tiger·tec Silver durability with a robust chipbreaker for stable machining of steel and cast iron; square 90° form and 0° negative rake ensure reliable edge life and process security. Order directly via Metav Werkzeuge or consult our specialists for application advice. SNMX0904ZNN-F57 WKP25S – milling indexable insert, Tiger·tec Silver, for steel & cast iron – Walter Tools A SNMX0904ZNN-F57 WKP25S indexable milling insert designed for productive milling of steel and cast iron, providing consistent cutting performance in demanding industrial applications Tiger·tec Silver coating for extended life Chipbreaker F57 for reliable chip control Square 90° form for versatile milling 0° negative rake for robust cutting Increased productivity through advanced coating and grade The combination of Tiger·tec Silver technology and a coated-carbide substrate delivers longer tool life and improved wear resistance compared with uncoated grades. The WKP25S grade is optimised for the thermal and mechanical demands of steel and cast iron machining according to ISO classifications, enabling longer uninterrupted production runs. The coated carbide structure reduces flank wear and maintains cutting-edge integrity, which translates into fewer index changes and lower overall machining costs. Stable cutting and predictable chip formation for consistent results The dedicated chipbreaker F57 provides reliable chip control across a range of cutting depths, reducing the risk of built-up edge and improving surface finish. With a square 90° geometry and 0° negative rake, the insert offers mechanical strength for interrupted or heavy cuts while maintaining dimensional consistency. These features support process reliability in series production and help achieve repeatable results with fewer tool interventions. Versatile geometry that simplifies tool selection and handling The insert’s compact dimensions and standard form make it suitable for a wide variety of milling holders and cutter bodies used in workshops and production environments. The tolerance class M and standardised seat geometry support straightforward replacement and minimise set‑up time. For customers seeking application-specific parameters, technical enquiries can be directed to Metav Werkzeuge for cutting data recommendations and compatibility checks. For application advice or to order SNMX0904ZNN-F57 WKP25S inserts from Walter Tools, please contact Metav Werkzeuge for direct supply and recommendations: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: SNMX0904ZNN-F57-WKP25S-WALTER Designation: SNMX0904ZNN-F57 WKP25S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKP25S Facts Insert size: 09 Thickness: 04 Free angle: 0° (negative) Plate form: Square 90° Chipbreaker: F57 Tolerance class: M Special features Material application: Steel (P), Cast iron (K) Coated carbide grade via Tiger·tec Silver technology Suitable for industrial milling operations Robust geometry for heavy and interrupted cuts FAQ What materials is this insert suitable for? The SNMX0904ZNN-F57 WKP25S is designed for machining steel (P) and cast iron (K) according to ISO classifications and offers optimised performance on these material groups. How does the Tiger·tec Silver coating benefit production? The Tiger·tec Silver coating on the WKP25S grade increases wear resistance and edge stability, extending tool life and reducing the frequency of index changes during production. Which chip behaviour can be expected with chipbreaker F57? The chipbreaker F57 promotes controlled, breaking chips in a wide range of cutting conditions, improving evacuation and reducing the risk of re-cutting or built-up edge. Is the insert suitable for heavy or interrupted milling? Yes, the square 90° geometry combined with a 0° negative rake provides mechanical robustness suited to heavy and interrupted milling tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used exclusively for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article is original, factory-new goods of the manufacturer Walter Tools.
SNMX0904ZNN-F57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WKP35G grade for reliable wear resistance and consistent chip control during demanding milling of Stahl and Gusseisen; for fast replenishment and technical advice contact Metav Werkzeuge. SNMX0904ZNN-F57 WKP35G — Milling indexable insert, Square 90°, 0° negative rake (Walter Tools) SNMX0904ZNN-F57 WKP35G is a Tiger‑tec Gold coated milling insert designed for productive face and shoulder milling in industrial environments, optimised for use on Stahl and Gusseisen. Tiger‑tec Gold coating for extended tool life Suitable for ISO P/K (Stahl and Gusseisen) Square 90° geometry with 0° negative rake F57 chipbreaker for stable chip formation Durable coating that reduces downtime and tooling costs The combination of the Tiger‑tec Gold coating and the WKP35G substrate provides enhanced wear resistance and improved edge stability, which translates into longer intervals between index changes and fewer unplanned stops. The coating reduces abrasive and adhesive wear under typical milling temperatures, while the grade is tuned for the thermal and mechanical demands of Stahl and Gusseisen machining. Firms seeking predictable performance in serial production will benefit from the reduced rework and consistent component tolerances delivered by this insert. Stable geometry for reliable chip control and surface quality The insert’s square 90° form and 0° negative rake provide a robust cutting edge that resists chipping during interrupted cuts or heavier engagements. The F57 chipbreaker is engineered to produce short, controlled chips on the targeted workpiece groups, improving evacuation and reducing heat concentration at the cutting edge. Together, these geometry choices support reproducible surface finish and dimensional accuracy, making the insert suitable for applications where process security and consistent part quality matter. Precision fit and predictable interchangeability for efficient workflows Manufactured to tolerance class M, the insert ensures repeatable seating and indexing in compatible toolholders, reducing setup time and minimising positional variance between insert changes. The standardised size and thickness codes make tool planning and CAD/CAM programming straightforward, while the robust substrate chemistry maintains edge integrity during medium-duty to demanding milling cycles. This combination of features supports higher productivity and easier planning in both one-off and batch production environments. Contact Metav Werkzeuge for application guidance and availability of genuine Walter Tools Tiger‑tec Gold milling inserts, or request tailored advice at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: SNMX0904ZNN-F57-WKP35G-WALTER Article designation: SNMX0904ZNN-F57 WKP35G Manufacturer: Walter Tools Facts Size code: 09 Thickness code: 04 Geometry: Quadrat 90° Rake angle: 0° (negative) Chipbreaker: F57 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKP35G (coated carbide) Material suitability: P / K (Stahl, Gusseisen) Execution: X Base designation: SNMX0904ZNN-F57 FAQ Which workpiece materials is this insert suited for? This SNMX0904ZNN-F57 WKP35G insert is specified for Stahl and Gusseisen, matching the P/K classification and delivering stable performance on both groups. What benefit does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold coating on the WKP35G grade enhances wear resistance and edge stability, extending service life and improving process reliability during milling. How does the F57 chipbreaker influence machining? The F57 chipbreaker produces short, controlled chips for predictable evacuation, which supports surface quality and reduces the risk of chip-related interruptions in production. What does tolerance class M mean for toolholders? Tolerance class M indicates consistent dimensional tolerances that ensure repeatable seating and interchangeability in compatible toolholders, aiding quick index changes and stable positioning. Is the square 90° geometry suitable for shoulder milling? Yes; the square 90° form combined with the 0° negative rake delivers a sturdy cutting edge suited to face and shoulder milling tasks, particularly where interrupted cuts or heavier depths of cut occur. Hersteller: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand‑new goods from the manufacturer.
SNMX0904ZNN-F57 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the high wear resistance of the Tiger·tec Gold grade combined with a secure chip control geometry for reliable machining of stainless steels and superalloys; order directly from Metav Werkzeuge or consult the product experts for application advice. SNMX0904ZNN-F57 WSM35G milling indexable insert — Tiger·tec Gold for stainless steels and superalloys — Walter Tools The SNMX0904ZNN-F57 WSM35G is a square 90° milling indexable insert designed for heavy and demanding machining of stainless steels and heat-resistant superalloys, providing stable cutting edges and optimised chip formation. Tiger·tec Gold coating for high wear resistance Optimised for stainless steel and superalloys Square 90° form with 0° negative rake Chipbreaker F57 for stable chip formation Durable grade and coating extend tool life under heat The insert is based on the WSM35G grade within the Tiger·tec Gold family, a coated cemented carbide solution developed for materials that are difficult to machine. The combination of a wear-resistant coating and a robust substrate reduces flank wear and supports a consistent cutting edge over multiple passes. This behaviour lowers the frequency of index changes and contributes to a more predictable tool-life cycle, which supports production planning and reduces unplanned downtime. The coated grade is particularly effective where high temperatures and adhesive wear would otherwise degrade performance. Geometry engineered for stable cutting and chip control A square 90° form with a 0° negative rake provides a strong cutting edge and a versatile clamping position, while the chipbreaker F57 promotes controlled chip segmentation. The insert thickness and tolerance class ensure reliable seating in standard milling toolholders, so the mechanical interface remains repeatable. These geometric features translate into fewer vibrations, improved surface integrity on the workpiece and consistent engagement behaviour during interrupted cuts, making the insert suitable for demanding operations where stability is essential. Targeted for ISO 513 groups M and S — practical advantages This grade is specified for ISO 513 material groups M (stainless steels) and S (heat-resistant superalloys and titanium), reflecting its focus on heat resistance and edge stability. In practice, the chemistry and coating of the grade reduce the tendency for built-up edge and thermal softening at the cutting zone. The result is improved dimensional consistency and a reduced risk of rework for components that require tight tolerances and good surface finish, such as aerospace and process-industry parts. Process reliability and shop-floor efficiency By combining a proven coating technology with an optimised chipbreaker and robust geometry, the insert supports steady machining parameters and repeatable outcomes. This predictability helps to increase throughput while maintaining component quality. The association with Walter Tools and the Tiger·tec Gold series signals established engineering and quality control in production; the insert therefore contributes to overall process reliability and supports continuous manufacturing targets. Contact Metav Werkzeuge to confirm application suitability and stock availability of the Walter Tools SNMX0904ZNN-F57 WSM35G Tiger·tec Gold insert — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number / SKU: SNMX0904ZNN-F57-WSM35G-WALTER Product type: milling indexable insert Manufacturer: Walter Tools Series / grade: Tiger·tec Gold / WSM35G Facts Insert size: 09 Thickness: 04 Free angle: 0° (negative) Form: Square 90° Tolerance class: M Special features Chipbreaker: F57 Coating technology: Tiger·tec Gold (coated carbide) Material suitability: stainless steels (ISO group M), superalloys/titanium (ISO group S) Execution: X Designation: SNMX0904ZNN-F57 WSM35G FAQ What materials is this insert suitable for? The SNMX0904ZNN-F57 WSM35G insert is specified for ISO material groups M and S, making it suitable for stainless steels and heat-resistant superalloys or titanium, depending on geometry. How does the chipbreaker F57 affect machining? Chipbreaker F57 promotes controlled chip segmentation and stable chip flow, which supports secure chip evacuation and consistent surface quality during milling operations. Why choose the Tiger·tec Gold grade WSM35G? The WSM35G grade in the Tiger·tec Gold family offers a balance of wear resistance and thermal stability tailored to difficult-to-machine materials, extending tool life and improving process reliability. Is the square 90° form advantageous for heavy cuts? Yes; the square 90° geometry combined with a 0° negative rake provides a robust cutting edge and allows multiple indexed positions, which is beneficial for heavy-duty milling and interrupted cuts. Can this insert be used in standard Walter toolholders? The insert is produced to common industry dimensions and tolerance class M, ensuring compatibility with standard clamping systems designed for SNMX-style square inserts. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only and do not indicate any affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
SNMX0904ZNN-F57 WSP45G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold PVD coating and the tough WSP45G grade together with a robust F57 chipbreaker for secure chip control and extended edge life; the square 90° geometry with 0° (negative) rake ensures stable, repeatable milling results. Order directly via Metav Werkzeuge or contact our consultants for application advice. SNMX0904ZNN-F57 SNMX0904ZNN-F57 WSP45G — Square 90° milling insert, Tiger‑tec Gold (Walter Tools) A SNMX0904ZNN-F57 WSP45G square 90° milling insert optimised for versatile milling of steel, stainless steel and heat-resistant superalloys and titanium in demanding production environments Tiger‑tec Gold PVD coating Grade WSP45G – tough and versatile Suitable for P / M / S workpiece groups Square 90° form with 0° negative rake Confident performance across steel, stainless steel and superalloys The combination of the Tiger‑tec Gold coating and the WSP45G cutting grade delivers a balance of wear resistance and edge toughness that is tailored to typical milling stresses. Designed for the ISO groups P / M / S, this grade addresses the heat and strain encountered when machining steels, the chip‑forming challenges of stainless steels and the thermal demands of superalloys and titanium. The coated carbide substrate reduces flank wear and helps maintain dimensional stability over longer tool life, which translates into fewer interruptions and more predictable production cycles. Robust geometry for secure cutting and repeatable quality A square 90° insert with 0° (negative) rake combines strength at the cutting edge with the ability to withstand interrupted cuts and heavier engagement. The integrated F57 chipbreaker supports controlled chip formation and evacuation, reducing the risk of built‑up edge on sticky materials and improving surface finish consistency. Because the insert is designed for mechanical stability rather than aggressive shear, the result is reliable tool behaviour under varying feed and depth conditions, which supports higher process security in batch and series production. Easy integration, consistent tolerance and industrial readiness The insert is supplied in a proven format (size code 09, thickness code 04) with tolerance class M, enabling straightforward replacement in standard Walter toolholders and compatible milling heads. The defined geometry and chipbreaker minimise set‑up variability, allowing shops to standardise feeds and speeds across similar operations. For tool planners and production managers, this means improved throughput and reduced variability in component quality while retaining the flexibility to address a broad range of materials typical for mixed‑material production runs. Contact Metav Werkzeuge today to discuss how Walter Tools' Tiger‑tec Gold grade WSP45G can improve milling stability and tool life in your processes — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: SNMX0904ZNN-F57-WSP45G-WALTER Name: Fräswendeschneidplatte SNMX0904ZNN-F57 WSP45G Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Series: Tiger‑tec Gold Grade: WSP45G Facts Plate size: 09 Plate thickness: 04 Plate form: Quadrat 90° Rake/relief angle: 0° (negativ) Tolerance class: M Special features Coating: Tiger‑tec Gold (PVD) Material application: P / M / S Chipbreaker: F57 Execution: X Series description: Tough, versatile PVD‑coated carbide for milling applications FAQ What materials is this insert suitable for? The SNMX0904ZNN‑F57 WSP45G insert from Walter Tools is designed for the ISO material groups P, M and S — covering steel, stainless steel and heat‑resistant superalloys/titanium. What benefit does the F57 chipbreaker provide? The F57 chipbreaker on this insert promotes controlled chip formation and evacuation, supporting improved surface finish and reduced risk of built‑up edge during milling. Why is the 0° (negative) rake useful in milling applications? A 0° (negative) rake increases cutting edge strength and resistance to chipping, making it particularly suitable for interrupted cuts, roughing passes and materials that impose high mechanical loads on the tool edge. How does tolerance class M affect replacement and setup? Tolerance class M denotes standardised dimensional accuracy, which simplifies insert replacement and helps maintain consistent machining parameters across tool changes. Is this insert compatible with standard Walter toolholders? Yes, the insert format (size 09, thickness 04, square 90°) is compatible with corresponding Walter toolholders and many industry standard milling bodies designed for SNMX‑style inserts. Walter Tools: Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
SNMX0904ZNN-F67 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of sharp cutting geometry, a dedicated F67 chipbreaker and the WAK15 uncoated carbide for productive machining of aluminium and other non‑ferrous metals. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. SNMX0904ZNN‑F67 WAK15 milling indexable insert — square 90°, WAK15 for aluminium (Walter Tools) The SNMX0904ZNN‑F67 WAK15 is a square 90° milling insert engineered for efficient machining of aluminium and non‑ferrous metals in high‑productivity environments Square 90° geometry for stable positioning WAK15 uncoated carbide for aluminium applications F67 chipbreaker optimised for non‑ferrous materials 0° negative rake for secure cutting action High productivity for aluminium and non‑ferrous machining The SNMX0904ZNN‑F67 is designed around the WAK15 uncoated carbide grade and an F67 chipbreaker, delivering reliable chip control when machining aluminium and other non‑ferrous alloys. The combination of a sharp cutting edge and a purpose‑built chipformer reduces built‑up edge and material adhesion, which in turn maintains cutting performance over longer runs. For production shops this translates into fewer interruptions, more consistent surface quality and predictable cycle times — a clear efficiency advantage in series milling. Secure cutting and repeatable positioning for robust production A square 90° insert form with 0° negative rake provides a secure seat and stable cutting attitude in the pocket, reducing vibration and improving repeatability across workpieces. The symmetric square shape enables indexable rotations for multiple cutting edges, supporting cost‑effective tool use. The substrate and geometry combination focuses on process stability and repeatable performance, so operators and CAM programmers can rely on consistent tool behaviour in milling cycles and light slotting tasks. Practical handling and application guidance for shop floors This insert is part of the Walter N‑sort system, created for uncomplicated selection and fast tool setup. The uncoated carbide composition favours applications where sharp edges and low friction are required, such as machining soft alloys, copper alloys and brass. When selecting cutting parameters, favour moderate chip loads and appropriate speeds for non‑ferrous materials; the optimised chipbreaker simplifies evacuation but benefits from stable feed rates to avoid built‑up material. The insert is suitable for high‑volume production where surface finish and reproducibility are key. Contact Metav Werkzeuge for tailored cutting data and application advice on Walter Tools inserts at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: SNMX0904ZNN-F67-WAK15-WALTER Designation: SNMX0904ZNN-F67 WAK15 Type: Milling indexable insert Series: Walter N‑Sortensystem Grade: WAK15 (uncoated carbide) Chipbreaker: F67 Shape: Square 90° Size: 09 Thickness: 04 Relief angle: 0° (negative) Tolerance class: M Execution: X Material group: N (aluminium and non‑ferrous metals) Facts Application: Aluminium and non‑ferrous metals (ISO group N) Indexable edges: 4 (square geometry) Coating: uncoated Intended use: Milling operations, light slotting, shoulder milling Special features Sharp cutting geometry for low adhesion Optimised chipforming for non‑ferrous alloys Symmetric design for economical indexing Stable seating with 0° negative rake for secure cutting FAQ What materials is this insert suitable for? The SNMX0904ZNN‑F67 WAK15 insert is intended for aluminium and other non‑ferrous metals (ISO group N); the WAK15 uncoated carbide and F67 chipbreaker are optimised for these materials. How many usable edges does the insert provide? The square 90° geometry provides multiple usable edges, enabling economical indexing and consistent performance across several settings. Is this grade coated or uncoated? WAK15 is an uncoated carbide grade designed for sharpness and low adhesion when machining non‑ferrous materials. Which series or system does this insert belong to? This insert is part of the Walter N‑Sortensystem, which simplifies selection for specific material groups and cutting tasks. What is the relief angle and why does it matter? The insert has a 0° negative rake, which improves seat stability and resists chip collapse in interrupted or heavier cuts, contributing to secure cutting action. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX120512-D27 WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, a D27 chipbreaker optimised for cast iron and a square 90° geometry for stable milling results — order the SNMX120512-D27 WKK25G directly via Metav Werkzeuge or ask the consultants for application support. SNMX120512-D27 WKK25G — Indexable milling insert, Tiger·tec Gold for cast iron (Walter Tools) A SNMX120512-D27 WKK25G indexable milling insert engineered for reliable, high‑productivity machining of cast iron components in industrial milling operations Tiger·tec Gold coating for wear resistance Optimised D27 chipbreaker for cast iron Square 90° insert with 1.2 mm corner radius 0° negative rake for stable cutting performance Consistent wear resistance tailored for cast iron The Tiger·tec Gold grade WKK25G is formulated for abrasive cast iron applications and provides enhanced wear resistance under the short, breaking‑type chip conditions typical of these materials. The coated carbide chemistry balances toughness and hardness to limit flank wear and protect the cutting edge, while the D27 chipbreaker is designed to control chip formation and evacuate fragments reliably. This results in a stable machining process with fewer unplanned tool changes and consistent component quality. Measurable productivity gains and process security With a square 90° geometry and 0° negative rake, the insert offers predictable cutting forces and robust edge support for interrupted or heavy milling of cast iron. The defined 1.2 mm corner radius contributes to improved tool life and surface integrity, helping to reduce cycle times and increase metal removal rates. These characteristics support a favourable cost‑per‑part calculation by lowering tooling consumption and minimising downtime, thus improving throughput in production environments. Practical integration and machining benefits The insert’s shape and tolerance class M enable straightforward use in standard milling tool bodies that accept square indexable plates. The compact design facilitates stable clamping and repeatable positioning, which helps to maintain dimensional accuracy across batches. The D27 chip control geometry simplifies swarf management in automated cells and manual setups alike. Where application parameters are critical, the combination of the grade and chipbreaker makes the component particularly suitable for aggressive roughing and semi‑finishing passes in cast iron. For specification checks, cutter compatibility advice or stock enquiries regarding Walter Tools inserts such as the SNMX120512‑D27 WKK25G, contact Metav Werkzeuge for tailored support and ordering information at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: SNMX120512-D27-WKK25G-WALTER Designation: SNMX120512-D27 WKK25G Product type: Fräswendeschneidplatte / indexable milling insert Manufacturer: Walter Tools Specifications Plate size: 12 Corner radius: 1.2 mm Plate form: Square 90° Rake angle: 0° (negative) Tolerance class: M Plate thickness: 05 Materials / Special features Series: Tiger·tec Gold Grade: WKK25G (coated carbide) Chipbreaker: D27 Suitable for: Cast iron Execution: X FAQ What materials is this insert intended for? The SNMX120512‑D27 WKK25G is specified for cast iron applications; the WKK25G grade and D27 chipbreaker are optimised for the abrasive and short‑chip behaviour of cast iron. How does the Tiger·tec Gold grade improve performance? Tiger·tec Gold provides a coated carbide surface that increases wear resistance and supports longer tool life under the high‑abrasion conditions encountered when machining cast iron. What is the advantage of a 0° negative rake? A 0° negative rake gives greater edge stability and resistance to chipping, which is beneficial for interrupted cuts and heavy roughing passes typical in industrial milling. Can the insert be used for finishing as well as roughing? The SNMX120512‑D27 WKK25G is primarily designed for robust roughing and semi‑finishing in cast iron; the 1.2 mm corner radius helps maintain surface quality but final finishing may require a dedicated geometry depending on tolerance and surface‑finish targets. How does the D27 chipbreaker affect chip control? The D27 design promotes predictable chip segmentation and evacuation in cast iron, reducing the risk of built‑up edge and improving machine uptime. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany; www.walter-tools.com The Walter AG (brand presentation: Walter Tools) with its headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes and do not imply any affiliation between our company and the manufacturers. The offered item is an original, factory‑new product of the manufacturer.
SNMX120512-D27 WKP25S Wendeplatten - Walter Tools
Take advantage of a high‑productivity, coated carbide solution combined with reliable chip control and a robust square geometry for predictable tool life and consistent part quality; order the insert directly via Metav Werkzeuge or consult the technical advisers if further specification is required. SNMX120512‑D27 WKP25S milling insert — Tiger·tec Silver, for steel & cast iron, square 90° — Walter Tools The SNMX120512‑D27 WKP25S is a square 90° milling insert with Tiger·tec Silver technology, designed for productive machining of steels and cast iron in demanding production environments. Tiger·tec Silver coated for high productivity Optimised for steel and cast iron machining Square 90° form with 1.2 mm corner radius 0° negative rake with D27 chipbreaker Built for high material removal and repeatable productivity The Tiger·tec Silver coating combined with the WKP25S grade offers a balanced mix of wear resistance and toughness, enabling sustained performance in serial machining. As a coated carbide insert engineered for ISO groups P and K, it handles the typical heat and chip behaviour of steel and the abrasive, short‑breaking chips of cast iron. The result is longer tool life and fewer insert changes, which supports stable cycle times and reduced tooling costs in production runs. Geometry that improves stability and surface quality A square 90° form with a 1.2 mm corner radius gives a robust cutting edge that tolerates higher cutting forces and interrupted cuts. The 0° negative rake increases edge strength where heavy engagement occurs, while the D27 chipbreaker promotes reliable chip control under varying cutting conditions. Together these features lower the risk of edge chipping and help maintain consistent surface finish, reducing rework and inspection time on finished components. Practical benefits for workshop efficiency Tolerance class M and the standardised SNMX120512 designation simplify tool selection and replacement for automated tool changers or manual toolrooms. The insert’s proven combination of coating and grade supports both roughing and semi‑finishing strategies: higher feed rates with confidence in the cutting edge, or conservative parameters for fine surface requirements. The design therefore supports process optimisation and quicker ramp‑up when introducing new parts or batch sizes. How the insert integrates into existing processes With a plate size code of 12 and thickness code 05, the insert fits common seat types used across many milling cutters; the square geometry offers flexible cutting orientations for pocketing, shoulder milling and peripheral operations. The chipbreaker geometry reduces the need for specialised tooling downstream and simplifies coolant and chip evacuation planning. For users less familiar with insert selection, specifying the Tiger·tec Silver WKP25S grade clarifies expectations for wear behaviour and suitable cutting ranges, making procurement and process documentation more straightforward. For reliable, high‑productivity milling in steel and cast iron, contact Metav Werkzeuge to specify Walter Tools' SNMX120512‑D27 WKP25S milling insert for your application; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number / SKU: SNMX120512-D27-WKP25S-WALTER Product name: SNMX120512‑D27 WKP25S Product type: milling insert (indexable insert) Series: Tiger·tec Silver Grade: WKP25S Manufacturer: Walter Tools Data Corner radius: 1.2 mm Plate size: 12 (code) Thickness: 05 (code) Rake angle: 0° (negative) Chipbreaker: D27 Tolerance class: M Special features Coating/technology: Tiger·tec Silver (coated carbide) Material suitability: steel (P), cast iron (K) Plate form: square 90° Application focus: productive milling, stable chip formation Execution: X FAQ What materials is the SNMX120512‑D27 WKP25S suitable for? The SNMX120512‑D27 WKP25S is targeted at steel (ISO group P) and cast iron (ISO group K) applications, reflecting the WKP25S grade’s balance for these material groups. What advantages does the Tiger·tec Silver technology provide? Tiger·tec Silver gives the insert improved wear resistance and toughness, supporting longer tool life and consistent cutting performance across varied steel and cast iron workloads. How does the D27 chipbreaker affect machining? The D27 chipbreaker promotes predictable chip formation and evacuation, reducing the chance of chip entanglement and aiding surface quality during continuous and interrupted cuts. Why choose a square 90° insert with a 1.2 mm corner radius? A square 90° geometry with a 1.2 mm radius offers strong cutting edges for both heavy engagement and flexible tool orientations, improving stability and lowering the risk of edge failure. Is this insert suitable for roughing and finishing operations? Yes, the combination of the WKP25S grade, Tiger·tec Silver coating and the D27 chipbreaker allows use in higher‑feed roughing as well as controlled semi‑finishing, depending on the selected cutting parameters. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. The Walter brand is mentioned for identification and explanatory purposes only; there is no connection implied between Metav Werkzeuge and the trademark holders. The offered article is an original, factory‑new product of the manufacturer.
SNMX120512-D27 WKP35G Wendeplatten - Walter Tools
Efficient, long-life performance from the WKP35G grade and Tiger·tec Gold coating provides stable cutting and reduced tool changes for high-output machining of steel and cast iron. Order the SNMX120512-D27 WKP35G directly via Metav Werkzeuge or ask our consultants for application advice. SNMX120512-D27 WKP35G - Milling insert, Tiger·tec Gold coating by Walter Tools A SNMX120512-D27 WKP35G milling insert engineered for robust shoulder and face milling, offering reliable chip control and long wear life in steel and cast iron applications Tiger·tec Gold coating for long tool life Optimised D27 chipbreaker geometry Square 90° insert for shoulder milling Suited for steel and cast iron machining Outstanding productivity through advanced grade and coating The combination of the WKP35G grade with Tiger·tec Gold technology gives this insert a coated carbide surface that improves wear resistance and maintains a stable cutting edge under demanding conditions. The multilayer coating reduces abrasive wear and helps to retard thermal damage during continuous milling, which results in fewer tool changes and longer productive cycles. In practice, that means more consistent component quality and lower process-related downtime, particularly on medium-to-high volume production runs where repeatable performance is critical. The insert’s design supports predictable tool life, aiding planning and cost-efficiency across production batches. Consistent chip control and secure cutting geometry The square 90° format together with the D27 chipbreaker provides reliable chip formation and evacuation during shoulder and face milling operations. A 1.2 mm corner radius delivers robust edge strength for moderate to heavy engagement while the 0° (negative) relief angle increases robustness for interrupted cuts and heavy radial depths of cut. These geometric choices improve stability at the cutting edge and reduce the likelihood of edge chipping when machining complex contours or interrupted surfaces. The net effect is a balance between good surface finish and tool resilience, with chip control that supports safer, more predictable machining cycles on demanding workpiece geometries. Application guidance for steel and cast iron with reliable process results Designed specifically for ISO groups P and K, the insert is optimised for machining steel and cast iron, where thermal loading and abrasive wear are typical concerns. The SNMX120512-D27 WKP35G is suitable for shoulder milling, face milling and similar operations where robust edge life and chip control matter. To exploit the insert’s advantages, pair it with rigid toolholding and stable workpiece setups; moderate depths of cut combined with steady feed rates typically deliver the best compromise between removal rate and tool life. For production environments seeking process reliability, this insert reduces unplanned stops and supports predictable output, making it a practical choice for workshops aiming for consistent part quality and throughput. Technical application support is available through Metav Werkzeuge for fine‑tuning cutting data to a specific machine and material combination. Contact Metav Werkzeuge for tailored application support and order handling for the SNMX120512-D27 WKP35G by Walter Tools Technical Data Article number: SNMX120512-D27-WKP35G-WALTER Designation: SNMX120512-D27 WKP35G Product type: Fräswendeschneidplatte (milling insert) Series: Tiger-tec Gold Grade: WKP35G Facts Insert size: 12 mm Corner radius: 1.2 mm Thickness: 0.5 mm Relief angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: D27 Shape: Square 90° Execution: X Material suitability: P (steel), K (cast iron) FAQ What materials is this insert suited for? The SNMX120512-D27 WKP35G is optimised for steel (ISO group P) and cast iron (ISO group K), matching the wear and chip formation characteristics of those materials. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating on the WKP35G grade improves wear resistance and thermal stability, which extends tool life and supports more consistent machining cycles. What milling applications suit a square 90° insert? A square 90° insert is ideal for shoulder milling and face milling where a strong cutting edge and reliable indexing are required. Why is the 0° (negative) relief angle advantageous? A 0° (negative) relief increases edge robustness for interrupted cuts and heavy engagement, reducing the risk of chipping under shock loads. Is there support for selecting cutting data for specific machines? Yes, Metav Werkzeuge can advise on cutting parameters and setup to match the SNMX120512-D27 WKP35G to a given machine and workpiece material. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory-new goods of the manufacturer.
SNMX120512-D27 WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the WPP35G grade and a 0° negative rake for robust, repeatable steel machining; the square 90° geometry with a 1.2 mm corner radius supports stable cutting and predictable tool life. Order the SNMX120512-D27 WPP35G directly via Metav Werkzeuge or consult our advisers if alignment with existing toolholders is required. SNMX120512-D27 WPP35G — Walter Tools milling indexable insert with Tiger·tec Gold coating, square 90° A SNMX120512-D27 WPP35G milling indexable insert optimised for steel machining, combining a coated carbide grade and a stable negative rake geometry for consistent cutting performance Tiger·tec Gold coating for wear resistance Designed for steel machining (P group) Square 90° insert, 1.2 mm corner radius Negative 0° rake for stable cutting Higher productivity through durable coated carbide The combination of Tiger·tec Gold surface technology and the WPP35G coated-carbide grade delivers increased abrasion resistance and more consistent edge life under typical steel cutting conditions. Coated carbide uses multiple thin layers to protect the substrate and to manage thermal loads; this reduces flank wear and supports longer intervals between indexing. For production environments this means fewer interruptions for insert changes and a steadier process output, which translates into measurable productivity gains and less variance in finished part quality. Stable geometry for predictable cutting behaviour The square 90° geometry with a 1.2 mm corner radius and a 0° negative rake creates a robust cutting edge suited to face and shoulder milling in steel (ISO group P). A square insert offers four cutting corners and defined entry angles, while the modest corner radius balances edge strength and surface finish. The zero-degree rake increases edge stability and is particularly advantageous for interrupted cuts or when machining heavier sections of steel where a stronger cutting edge is needed. The chipbreaker D27 supports controlled chip formation, helping to maintain surface quality and reduce recutting. Practical integration and selection guidance for toolrooms When integrating this indexable insert into a milling system, match the SNMX120512-D27 WPP35G with a compatible cutter body that accepts square 90° inserts and provides correct seating and clamping. Correct clamping and the use of appropriate torques preserve the insert seat and ensure repeatable runout. Selection should consider the desired balance between tool life and surface finish: the WPP35G grade is aimed primarily at steel machining with a weighted focus on wear resistance and universality across common steel grades. For assistance with toolholder compatibility or process optimisation, Metav Werkzeuge can provide application-oriented advice and supply matching cutter bodies. Contact Metav Werkzeuge for tailored recommendations on Walter Tools milling inserts and assistance with toolholder matching — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 Technical data SKU: SNMX120512-D27-WPP35G-WALTER Article designation: SNMX120512-D27 WPP35G Series: Tiger·tec Gold Grade: WPP35G Manufacturer: Walter Tools Facts Size: 12 mm Corner radius: 1.2 mm Plate thickness: 05 Free rake: 0° (negative) Tolerance class: M Special features Coating technology: Tiger·tec Gold Substrate: coated carbide Geometry: Square 90° Chipbreaker: D27 Suitable for: Steel (ISO group P) FAQ What materials is this insert suitable for? The SNMX120512-D27 WPP35G insert from Walter Tools is designed for machining steels classified under ISO group P; the WPP35G grade and Tiger·tec Gold coating are optimised for typical steel heat generation and chip formation. What is the geometry and corner radius of the insert? The insert features a square 90° form with a 1.2 mm corner radius, delivering a balance of edge strength and surface finish for general milling applications. Which coating and grade does the insert use? This item is supplied in the Tiger·tec Gold coating technology and the WPP35G coated-carbide grade, ensuring good wear resistance and broad applicability in steel machining. How does the 0° negative rake affect performance? A 0° negative rake increases cutting-edge robustness and stability, making the insert suitable for heavier cuts and interrupted milling where a stronger edge is beneficial. How should this insert be integrated into a milling system? Pair the SNMX120512-D27 WPP35G with a cutter body designed for square inserts, ensure proper seating and clamping, and check that the chipflow and coolant application align with the D27 chipbreaker characteristics. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original, factory-new goods of the manufacturer.
SNMX120512-F27 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Silver coating, a reinforced 1.2 mm corner radius and a square 90° geometry for stable, productive milling of steel and cast iron. Order the insert directly via Metav Werkzeuge or consult Metav Werkzeuge's technicians for process optimisation. SNMX120512-F27 WKP25S square milling insert, Tiger·tec Silver — for steel and cast iron | Walter Tools A SNMX120512-F27 WKP25S square 90° indexable insert engineered for robust roughing and reliable semi-finishing in demanding steel and cast iron applications Tiger·tec Silver coating for long tool life Designed for steel and cast iron machining Square 90° insert with 1.2 mm corner radius Negative 0° rake for stable cutting Proven wear resistance that extends tool life The combination of the Tiger·tec Silver coating and the WKP25S grade offers pronounced resistance against abrasive wear and thermal degradation, which translates into longer tool life under typical milling conditions. Coated carbide technology reduces flank wear and maintains cutting-edge integrity during prolonged operation, making it suitable for high-volume production where predictable tool change intervals and consistent part quality are priorities. This behaviour supports lower running costs through fewer interruptions and better process predictability. Geometry engineered for stable material removal A square 90° plate form with a 1.2 mm corner radius increases edge robustness and enables heavier radial engagement while preserving acceptable surface finish. The 0° negative rake provides a more robust cutting edge and reduces the tendency for chipping during interrupted cuts or when machining irregular surfaces. Together, these geometric features support stable cutting forces and make the insert particularly effective for roughing passes and mixed operation cycles where tool reliability is essential. Optimised chip control and thermal management The integrated F27 chipbreaker geometry and the Tiger·tec Silver technology promote controlled chip formation when cutting both unalloyed and alloyed steels as well as cast iron. By guiding chip flow and dissipating heat more evenly across the cutting edge, the system lowers the risk of built-up edge and edge failure. Improved chip control reduces rework and contributes to a safer, more efficient machining environment, especially on tougher workpiece grades commonly encountered in production workshops. Process reliability and application scope Manufactured to tolerance class M, the insert is suitable for systematic indexability and repeatable seating in multi-insert toolholders, which helps to reduce setup variation and improve cycle-time stability. The component’s compact dimensions and standardised design enable compatibility with a wide range of milling bodies used in industry applications. Metav Werkzeuge can supply the insert in matching tool systems and advise on cutting data to achieve the best compromise between productivity and tool life. For tailored cutting data, availability and application advice on Walter Tools’ Tiger·tec Silver inserts, contact Metav Werkzeuge – info@metav-werkzeuge.com or call +49 2822 7131930 for immediate support and delivery options. Technical data Article number: SNMX120512-F27-WKP25S-WALTER Designation: SNMX120512-F27 WKP25S Manufacturer: Walter Tools Facts Insert size: 12 mm Corner radius: 1.2 mm Plate thickness: 05 Tolerance class: M Rake angle: 0° (negative) Plate form: Square 90° Chipbreaker: F27 Special features Coating: Tiger·tec Silver Grade: WKP25S (coated carbide) Material suitability: P (steel) and K (cast iron) Series: Tiger-tec Silver Execution: X FAQ What materials is this insert suitable for? The SNMX120512-F27 WKP25S insert from Walter Tools is designed for machining steel (ISO group P) and cast iron (ISO group K), offering optimised performance for those material families. How does the Tiger·tec Silver coating benefit machining? Tiger·tec Silver increases wear resistance and thermal stability, which helps to maintain edge life and reduce flank wear when cutting abrasive or heat-generating materials. Why choose a square 90° insert with a 1.2 mm corner radius? A square 90° geometry with a 1.2 mm corner radius provides a strong cutting edge for heavier engagements and interrupted cuts, improving stability and reducing the likelihood of chipping. Is this insert suitable for interrupted cutting and roughing operations? Yes, the combination of 0° negative rake, sturdy geometry and the F27 chipbreaker makes the insert well suited to roughing and interrupted cutting tasks that demand edge robustness. How does the tolerance class affect installation? Tolerance class M ensures consistent seating and indexability in standard toolholders, supporting repeatable positioning and reliable production results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only; no connection exists between Metav Werkzeuge and the named brands. The offered article is original, factory-new goods of the manufacturer Walter Tools.
SNMX120512-F27 WKP35G Wendeplatten - Walter Tools
Combine long tool life, precise chip control and a robust square geometry to keep milling cycles productive and predictable; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. SNMX120512-F27 WKP35G – Milling Insert (Tiger·tec Gold), F27 Chipbreaker by Walter Tools SNMX120512-F27 WKP35G is a coated milling insert designed for medium- to heavy-duty milling in steel and cast iron, offering a durable cutting grade and a geometry optimised for stable chip formation. Tiger·tec Gold coating for long tool life Optimised F27 chipbreaker for stable chips Square 90° geometry with 1.2 mm corner radius Suited for steel and cast iron machining Maximise uptime with a proven coating system The insert’s Tiger·tec Gold technology and WKP35G grade provide a balanced combination of wear resistance and toughness, resulting in extended tool life under real production conditions. The coated carbide construction resists abrasive wear typical when machining cast materials, while maintaining edge stability during interrupted cuts. For operations where predictable tool change intervals and consistent component quality matter, this insert delivers measurable improvements in process reliability and cost per part. Geometry engineered for reliable chip control A dedicated F27 chipbreaker and square 90° shape generate compact, controlled chips even on varying feeds. The 1.2 mm corner radius increases edge strength and reduces vibration in heavy engagement, while the 0° (negative) relief angle supports robust cutting edges for roughing operations. These design choices together minimise unexpected downtime and produce repeatable surface finishes, making the insert a practical choice for demanding milling tasks. Designed specifically for steel and cast iron workloads The grade is tailored for the ISO groups steel (P) and cast iron (K), so the cutting geometry and coating are aligned with the thermal and wear characteristics of these materials. For steel, the insert copes with continuous heat generation and ductile chip formation; for cast iron, the coating and edge preparation handle abrasive inclusions and short, breakable chips. This targeted suitability simplifies tool selection and reduces the need for frequent trial cuts. Seamless integration into productive machining cells With a tolerance class M and a standard square format, the insert fits established tool holders and indexable systems, enabling fast index changes and consistent positioning. The combination of predictable wear behaviour and Walter Tools manufacturing standards supports process stability and easier planning of tool inventories. For workshops aiming to increase throughput without sacrificing repeatability, the insert contributes directly to higher machining efficiency. Contact Metav Werkzeuge for tailored application advice on Tiger·tec Gold inserts and secure optimal milling performance with Walter Tools. Technical Data SKU: SNMX120512-F27-WKP35G-WALTER Article: SNMX120512-F27 WKP35G Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Insert size: 12 mm Corner radius: 1.2 mm Relief angle: 0° (negative) Tolerance class: M Thickness: 05 Special features Coating / grade: WKP35G (coated carbide) Chipbreaker: F27 Shape: Square 90° Applicable materials: Steel (P) and Cast iron (K) Execution: X FAQ What materials is this insert suitable for? The SNMX120512-F27 WKP35G insert is designed primarily for steel (P) and cast iron (K) applications, with the coating and geometry optimised for both material groups. How does the F27 chipbreaker benefit milling? The F27 chipbreaker on this insert produces compact, controllable chips, improving evacuation and reducing the risk of re-cutting, which supports stable cutting forces and better surface integrity. Can this insert be used for roughing operations? Yes, the square 90° geometry combined with the 1.2 mm corner radius and negative relief angle make it suitable for robust roughing passes where a strong cutting edge is required. What does the Tiger·tec Gold series offer in practice? Tiger·tec Gold brings a balanced wear resistance and toughness profile; in the SNMX120512-F27 WKP35G this translates into longer in-process life and consistent performance across variable cutting conditions. Is the insert compatible with standard toolholders? The insert’s format and tolerance class M ensure compatibility with common indexable milling holders, enabling straightforward integration into existing tooling setups. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names are used for explanatory purposes only; there is no connection between our company and the mentioned brands. The offered item is original, factory-new goods from the manufacturer.
SNMX120512-F27 WKP35S Wendeplatten - Walter Tools
Take advantage of the proven Tiger·tec Silver coating and the WKP35S grade for robust machining of steel and cast iron; the square 90° geometry with a 1.2 mm corner radius and F27 chipbreaker delivers stable chip control and extended tool life. Order the SNMX120512-F27 WKP35S directly via Metav Werkzeuge or consult the Metav team for application advice. SNMX120512-F27 WKP35S – Square indexable milling insert, Tiger·tec Silver coating for steel and cast iron, Walter Tools A SNMX120512-F27 WKP35S indexable milling insert designed for productive face and shoulder milling operations in steel and cast iron applications, combining a robust square geometry with a chipbreaker tuned for secure chip control. Tiger·tec Silver coating for high wear resistance Optimised F27 chipbreaker for stable chips Square 90° geometry with 1.2 mm corner radius Designed for steel and cast iron machining Confident machining performance for steel and cast iron The SNMX120512-F27 WKP35S is engineered to deliver consistent results when machining ferrous materials. The combination of the Tiger·tec Silver surface treatment and the WKP35S grade produces a coated carbide cutting edge that resists abrasive wear typical of cast materials and the adhesive wear seen in steel. The designation P/K indicates suitability for ISO group P (steel) and K (cast iron); this means optimised heat resistance and chip behaviour for common turning and milling scenarios, helping maintain dimensional stability and reducing unexpected tool changes. Longer service life through coating and grade selection A key economic advantage lies in the coating and substrate pairing. The Tiger·tec Silver coating reduces flank and crater wear, which in turn extends indexable insert life and increases productive cutting time between index changes. Choosing the WKP35S grade improves process reliability under interrupted cuts and variable feed conditions, lowering tool consumption per component. For production environments, this translates directly into fewer tool exchanges and steadier cycle times. Geometry and chip control that protect the process The insert’s square 90° form and 1.2 mm corner radius provide a strong cutting edge that tolerates higher radial forces and supports aggressive feeds where geometry allows. The F27 chipbreaker is optimised for predictable chip fragmentation, promoting safe evacuation in both steel and cast iron machining. A 0° negative rake further strengthens the cutting edge, improving resistance to impact at entry and when passing interruptions—an important factor in mixed-operation cell manufacturing where part geometry varies. Practical productivity benefits on the shop floor Using this indexable insert reduces setup complexity: the square shape supports multiple cutting orientations and straightforward pocketing on standard toolholders, while the measured tolerance class M ensures repeatable seating and reliable indexing. For milling operations that demand both surface quality and durability, the insert offers a balance of finish and economy. The simplified tool handling and predictable wear behaviour help planners forecast tooling costs and maintain consistent part quality in medium- to high-volume runs. For application-specific recommendations or to secure fast delivery of the Tiger·tec Silver SNMX120512-F27 WKP35S from Metav Werkzeuge, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 — experts are available to advise on toolholder pairing and cutting data Technical data Article number: SNMX120512-F27-WKP35S-WALTER Product type: Fräswendeschneidplatte Designation: SNMX120512-F27 WKP35S Brand: Walter Tools Facts Size: 12 mm Corner radius: 1.2 mm Thickness: 0.5 mm Relief angle: 0° (negative) Tolerance class: M Special features Series: Tiger-tec Silver Grade: WKP35S Chipbreaker: F27 Plate form: Square 90° Material applicability: P / K (steel, cast iron) Substrate: Coated carbide Execution: X FAQ What materials is this insert suited for? The SNMX120512-F27 WKP35S is designed for steel and cast iron (ISO groups P and K), making it suitable for a wide range of ferrous machining tasks where predictable chip control and wear resistance are required. How does the Tiger·tec Silver coating benefit production? The Tiger·tec Silver coating on this insert reduces abrasive and adhesive wear, extending tool life and improving process stability for longer uninterrupted production runs. What does F27 chipbreaker mean in practice? The F27 chipbreaker is optimised for fragmenting chips reliably in both steel and cast iron, improving evacuation and reducing the risk of entanglement or surface damage during milling. Can this insert be used in interrupted cuts? Yes. The square geometry, 1.2 mm corner radius and 0° negative rake provide a robust cutting edge that tolerates impact and interrupted machining typical in shoulder milling and complex part profiles. Which toolholders are compatible with this insert designation? The SNMX120512-F27 WKP35S fits standard Walter-compatible indexable milling holders designed for SNMX-style square inserts; verify seat type and clamping style with toolholder specifications. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX120512-F27 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a robust 1.2 mm corner radius, and an optimised F27 chipbreaker for stable, economical milling of steel; contact Metav Werkzeuge for application advice or to place an order through their consulting team. SNMX120512-F27 WPP35G — milling insert, square 90°, Tiger·tec Gold, Walter Tools A SNMX120512-F27 WPP35G is a square milling insert developed for machining steel, combining the Tiger·tec Gold coating technology with a defined negative rake for secure, repeatable cutting performance. Tiger·tec Gold coated carbide for long life Square 90° design for versatile milling 1.2 mm corner radius for robust edge strength Optimised F27 chipbreaker for steel machining Reliable, cost-effective cutting with Tiger·tec Gold The Tiger·tec Gold coating and the Walter WPP35G designation mark a coated carbide solution engineered for endurance in steel milling. The coating reduces flank wear and supports consistent cutting-edge behaviour, which translates into extended tool life and fewer index changes. For production settings this means predictable component quality and reduced tooling costs per part. The combination of a wear-resistant grade and dedicated coating improves resistance to the thermal and mechanical stresses that occur during standard steel machining (ISO P). Stable geometry for secure cuts and predictable tool life The square 90° plate form with a 1.2 mm corner radius creates a stable cutting geometry that sustains edge strength during interrupted or heavy cuts. The defined negative 0° rake contributes to a stronger cutting edge and reduced tendency to chip under load, making the insert suitable for demanding finishing and roughing operations where edge security matters. This geometry supports consistent dimensional results and reduces the need for frequent tool changeovers. Efficient chip control and process reliability The integrated F27 chipbreaker is optimised for steel applications and enhances chip segmentation and evacuation, which helps maintain machine uptime and surface quality. Classified for ISO group P, the grade handles the typical heat and chip-formation behaviour of unalloyed and alloyed steels. Together with the tolerance class M, the insert supports reliable seating and repeatability in clamping systems, contributing to uniform surface finish and reduced rework. Simple integration and practical workshop benefits The insert’s dimensions and indexable format allow straightforward integration into standard milling tool holders that accept SNMX-style plates. The square form offers multiple usable cutting edges, reducing tooling consumption per edge compared with single‑edge solutions. For production planners and shopfloor technicians, the result is a pragmatic balance of performance and handling: fewer tool changes, stable process windows and the capacity to maintain throughput without sacrificing component quality. The SNMX120512-F27 WPP35G thus fits well where productivity and repeatability are priorities. Contact Metav Werkzeuge to discuss the suitability of the Walter Tools SNMX120512-F27 WPP35G for specific steel applications and to request tailored cutting data or ordering assistance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: SNMX120512-F27-WPP35G-WALTER Designation: SNMX120512-F27 WPP35G Product type: milling insert Manufacturer: Walter Tools Core specifications Size: 12 mm Corner radius: 1.2 mm Cutting geometry: square 90° Rake: 0° (negative) Chipbreaker: F27 Grade / sort: WPP35G Series: Tiger·tec Gold Thickness code: 05 Tolerance class: M Features and suitability Coating: Tiger·tec Gold (coated carbide) Material application: steel (ISO P) Execution: X Plate form: square Series description: coated carbide grade for steel machining Optimised for process stability and surface quality FAQ What materials is this insert intended for? The SNMX120512-F27 WPP35G is designed primarily for machining steel and is specified for ISO P materials. How does the Tiger·tec Gold coating benefit production? Tiger·tec Gold on the SNMX120512-F27 WPP35G reduces wear and improves thermal resistance, extending edge life and helping to maintain consistent part quality. What is the advantage of the F27 chipbreaker? The F27 chipbreaker on this insert supports controlled chip formation and evacuation when machining steel, contributing to stable machining and improved surface finish. Can the square plate deliver multiple cutting edges? Yes; the square 90° geometry of the SNMX120512-F27 WPP35G provides several usable cutting edges, which lowers tooling consumption per edge. What does tolerance class M mean for workshop use? Tolerance class M indicates a standardised dimensional accuracy that supports reliable fit and repeatability in indexable tool holders when using the SNMX120512-F27 WPP35G. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are mentioned for explanation only. There is no connection between our company and the listed brands; the offered article is an original, factory-new product of the manufacturer.
SNMX120512-F57 WKK25G WKK25G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and the WKK25G carbide grade for consistent, productive machining of cast iron; the optimised F57 chipbreaker and square 90° geometry ensure reliable chip control and reproducible edge life. Order directly via Metav Werkzeuge or consult our specialists for tailored machining advice. SNMX120512-F57 WKK25G milling indexable insert by Walter Tools — Tiger·tec Gold for cast iron The SNMX120512-F57 WKK25G is a square milling insert designed for productive machining of cast iron, combining a coated carbide grade from the Tiger·tec Gold family with a dedicated F57 chipbreaker for improved process security. Tiger·tec Gold coated grade WKK25G Optimised chip control F57 Square 90° insert geometry Proven performance on cast iron Higher productivity on abrasive cast iron The coated carbide WKK25G grade, part of the Tiger·tec Gold series, is formulated to resist the abrasive wear typical for cast iron machining. The insert's combination of coating technology and carbides delivers stable chip formation and longer tool life under demanding conditions, allowing higher material removal rates without sacrificing surface quality. For operations that require predictable performance on abrasive workpieces, this insert reduces unscheduled tool changes and supports continuous production. Predictable chip control and surface finish Equipped with the F57 chipbreaker, the insert produces short, easily evacuable chips that lower the risk of re-cutting and machine stoppages. Short, well-formed chips assist coolant flow and simplify swarf handling, which in turn supports consistent part finish and reduces secondary cleaning. The focused chip control also enables machining parameters to be set more aggressively while maintaining process stability, yielding faster cycle times and improved throughput. Robust geometry for secure cutting conditions The square 90° shape with a 1.2 mm corner radius and 0° negative rake provides a robust cutting edge suited to interrupted cuts and medium-to-heavy milling loads. The insert's 12 mm size and standard thickness code ensure compatibility with a wide range of toolholders designed for square inserts. Together, these geometric features give stable seating and repeatable edge position, which benefits repeatability and dimensional control in serial production. Practical selection and application guidance When specifying inserts for cast iron operations, consider the benefits of a coated grade tailored to abrasive materials and a chipbreaker that matches the intended feed and depth of cut. The combination of the Tiger·tec Gold coating and the F57 chip geometry makes this insert particularly suitable for finishing to medium roughing steps on grey and nodular cast iron. For customers seeking to increase uptime and maintain consistent surface quality, this insert offers a pragmatic balance of wear resistance and chip control. Contact Metav Werkzeuge for expert advice on Walter Tools Tiger·tec Gold inserts and assistance with selecting the correct grade and chipbreaker for specific cast iron applications: info@metav-werkzeuge.com • +49 2822 7131930 Technical Data Article number: SNMX120512-F57-WKK25G-WALTER SKU: SNMX120512-F57-WKK25G-WALTER Product type: Fräswendeschneidplatte / milling indexable insert Manufacturer: Walter Tools Grade: WKK25G Facts Insert size: 12 mm Corner radius: 1.2 mm Relief angle: 0° Plate shape: square 90° Chipbreaker: F57 Thickness code: 05 Tolerance class: M Special features Series: Tiger·tec Gold Material: coated carbide Optimised for: cast iron machining Performance attributes: stable chip formation, wear resistance, productive machining Execution code: X ISO designation: SNMX120512-F57 WKK25G FAQ What materials is this insert designed for? The SNMX120512-F57 WKK25G milling insert from Walter Tools is designed primarily for cast iron; the WKK25G grade is optimised for abrasive cast materials and short, breaking chips. What benefits does the Tiger·tec Gold grade provide? The Tiger·tec Gold coating on the WKK25G grade improves wear resistance and process stability, allowing longer edge life and consistent performance in repetitive machining of cast iron. How does the F57 chipbreaker affect machining? The F57 chipbreaker produces short, controlled chips that improve evacuation and reduce the risk of chip entanglement, contributing to reliable machining and improved surface quality. What are the key geometry features to note? This insert features a square 90° shape, a 1.2 mm corner radius and 0° negative rake, providing a robust edge for interrupted cuts and stable seating in the toolholder. Is the SNMX120512-F57 WKK25G suitable for aggressive cutting parameters? Thanks to its coated carbide grade and F57 chip control, the insert supports more aggressive feeds and depths of cut while maintaining process reliability on cast iron, but final parameters should be validated under actual cutting conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SNMX120512-F57 WKP25S Wendeplatten - Walter Tools
Take advantage of the WKP25S grade's combination of high wear resistance and stable chip formation together with the Tiger‑tec Silver coating for reliable, productive milling of Stahl and cast iron; order directly via Metav Werkzeuge or consult the Metav Werkzeuge team for application advice. SNMX120512-F57 WKP25S Milling Insert (Square 90°, Tiger‑tec Silver) by Walter Tools A SNMX120512-F57 WKP25S milling insert engineered for high‑productivity finishing and roughing in Stahl and cast iron with a Tiger‑tec Silver coated carbide grade. SNMX120512-F57 WKP25S by Walter Tools Tiger‑tec Silver coated carbide grade Square 90° insert with 1.2 mm corner radius Optimised for Stahl and cast iron machining Increased productivity through a wear‑resistant grade The coated carbide WKP25S grade, part of the Tiger‑tec Silver series, offers a clear performance advantage when machining Stahl and cast iron. Designed to tolerate the higher thermal loads and typical chip formation of these materials, the grade provides improved tool life and consistent cutting performance. By combining the coating technology with a geometry tuned for robust engagement, the insert reduces flank and crater wear, which translates into fewer tool changes and higher machine uptime. The result is a measurable gain in productivity and process economy for both finishing and semi‑roughing operations. Reliable chip control and stable cutting geometry The square 90° form with a 1.2 mm corner radius and the F57 chipbreaker create predictable chip shapes and evacuation, especially in interrupted or variable cuts. The 0° (negative) relief angle increases edge strength and resists edge chipping under higher feed rates. In practice, this means the insert maintains dimensional stability on demanding passes and improves surface integrity on the workpiece. The chipbreaker geometry is optimised to break and guide swarf away from the cutting zone, reducing recutting and the risk of built‑up edge—advantages that directly affect cycle times and part quality. Consistent part quality with industrial robustness Tolerance class M and the Tiger‑tec Silver production standards ensure repeatable performance across batches. The combination of the coated carbide substrate and the engineered chipbreaker supports repeatable surface finishes and reliable process security across production runs. For manufacturing environments that demand predictable tool life and steady results, this insert is suited to catalogue‑ and geometry‑dependent applications in both steel and cast iron ISO groups. The robust execution and Walter Tools system compatibility provide an industrially proven choice for shops seeking dependable milling solutions. Contact Metav Werkzeuge for tailored application recommendations or to request a process suitability assessment for the Walter Tools SNMX120512-F57 WKP25S milling insert. Technical data Article number: SNMX120512-F57-WKP25S-WALTER Designation: SNMX120512-F57 WKP25S Product type: Fräswendeschneidplatte Facts Insert shape: Quadrat 90° Corner radius: 1.2 mm Relief angle: 0° (negativ) Insert size: 12 mm Thickness: 05 Special features Series: Tiger‑tec Silver Grade: WKP25S (beschichtetes Hartmetall) Chipbreaker: F57 Material suitability: Stahl, cast iron Tolerance class: M Execution: X FAQ Which materials is this insert suitable for? The SNMX120512-F57 WKP25S insert is designed for machining Stahl (ISO group P) and cast iron (ISO group K) as indicated by the WKP25S grade and Tiger‑tec Silver series. What is the purpose of the F57 chipbreaker? The F57 chipbreaker on the SNMX120512-F57 WKP25S promotes controlled chip formation and evacuation, improving surface finish and reducing the chance of recutting in interrupted cuts. How does the 0° negative relief affect performance? A 0° (negative) relief increases edge strength and stability under heavy or interrupted cutting, which enhances tool life and process reliability for demanding milling tasks. Can this insert be used for both finishing and roughing? Yes, the combination of the WKP25S grade, robust geometry and 1.2 mm corner radius makes the insert suitable for both finishing and semi‑roughing applications, depending on the specific machining parameters. What tolerance class does the insert comply with? The insert is supplied to tolerance class M, supporting consistent seating and repeatable performance in standard toolholders. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is original and brand‑new from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com