ZDGT200508R-K85 WK10 Wendeplatten - Walter Tools
Take advantage of the combination of WK10 uncoated carbide, K85 chipbreaker and a 15° clearance angle for predictable chip formation and efficient milling; order directly via Metav Werkzeuge or consult our specialists for application advice. ZDGT200508R-K85 WK10 milling insert, K85 chipbreaker, 15° clearance — Walter Tools ZDGT200508R-K85 WK10 is a milling insert intended for face and shoulder milling in general machining, offering robust edge geometry and controlled chip formation for medium to high-volume production Uncoated carbide WK10 grade K85 chipbreaker for stable chips 0.8 mm corner radius for robust edges 15° clearance angle for versatile milling Reliable cutting performance through optimised geometry The insert combines the WK10 uncoated carbide grade with a defined K85 chipbreaker to deliver consistent chip control across a range of common machining tasks. The controlled chip splitting reduces interruptions and helps maintain machining stability, which is particularly important when cycle times must be kept short. The geometry promotes predictable cutting forces, enabling efficient material removal while supporting repeatable surface quality on machined components. Durable edge design for longer productivity windows A 0.8 mm corner radius and the specific edge preparation ensure better resistance to edge chipping during intermittent cuts. This robust form reduces the frequency of insert changes and supports a steady production flow with fewer machine stops. Where tool life and reproducibility matter, the combination of edge radius and uncoated carbide base provides mechanical strength rather than relying solely on coating technologies, making it suitable for many standard milling operations. Practical machining flexibility and set-up simplicity The 15° clearance angle enables secure engagement in face-milling and shoulder operations while minimising rubbing and heat build-up at the flank. The insert’s dimensional coding and thickness designation allow straightforward selection for compatible toolholders, simplifying inventory and changeover. For toolrooms aiming to standardise on versatile insert types, this indexable design reduces complexity and eases logistical planning without compromising machining capability. Material suitability and application notes The insert is supplied in the Walter Schneidstoffsorte - Serie offen and the WK10 grade is an uncoated carbide; refer to the product matrix for exact material recommendations. Where high surface finish or very hard materials are required, check the specific suitability of the grade before series adoption. For common steels and typical workshop alloys, the insert offers a balanced performance profile, producing controlled chips and maintaining dimensional stability across standard milling tasks. Contact Metav Werkzeuge to discuss the ZDGT200508R-K85 WK10 for specific applications or to arrange supply and technical clarification Technical Data Article number: ZDGT200508R-K85-WK10-WALTER Label: Fräswendeschneidplatte ZDGT200508R-K85 WK10 Walter Tools Product type: Fräswendeschneidplatte (milling insert) Manufacturer: Walter Tools ISO designation: ZDGT200508R-K85 WK10 Facts Clearance angle: 15° Corner radius: 0.8 mm Size: 20 Thickness code: 05 Special features Chipbreaker: K85 Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Tolerance class: G Execution: T Material: Katalogabhängig FAQ What materials is this insert suitable for? The WK10 grade is an uncoated carbide offered in the Walter Schneidstoffsorte series; suitability depends on the product matrix, but the ZDGT200508R-K85 WK10 is typically used for common steels and workshop alloys. How does the K85 chipbreaker affect machining? The K85 chipbreaker provides controlled chip formation and evacuation, which improves process stability and reduces the risk of re-cutting chips during milling operations with the Walter Tools insert. What does the thickness code 05 mean? The thickness is given as the designation code 05 for toolholder compatibility; refer to the toolholder documentation to select the correct seat and clamping for the insert size. Is the corner radius suitable for roughing? The 0.8 mm corner radius offers a robust cutting edge that is well suited to many roughing and semi-finishing applications where stronger edge strength is desired. How is the clearance angle relevant to setup? The 15° clearance angle reduces flank contact and heat generation, allowing consistent engagement in face and shoulder milling and supporting reliable surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT200508R-K85 WNN15 WNN15 Wendeplatten - Walter Tools
Take advantage of the combination of a coated carbide grade (WNN15), the chipbreaker K85 and a 15° relief for consistent chip control and dependable edge life; order directly via Metav Werkzeuge or consult the specialists for application-specific recommendations. ZDGT200508R-K85 WNN15 milling indexable insert — chipbreaker K85, 15° relief, Walter Tools ZDGT200508R-K85 WNN15 is a milling indexable insert designed for versatile milling tasks in industrial production, featuring a chipbreaker for controlled chips and a geometry optimised for repeatable results Coated carbide grade WNN15 Chipbreaker K85 for consistent chip control 15° relief angle for versatile milling 0.8 mm corner radius for reliable edge strength Increased productivity through controlled chip formation and stable cutting The coated carbide composition of this insert (grade WNN15) combines wear resistance with reliable cutting performance, making it well suited to production environments where predictable tool life matters. The integrated chipbreaker K85 reduces long, stringy chips and promotes efficient evacuation, which in turn supports higher feed rates and reduces downtime for chip clearing. With a 15° relief angle, the geometry offers a balance between strength and cutting action, enabling consistent surface finish and improved cycle times in repetitive milling operations. The insert designation appears as ZDGT200508R-K85 WNN15 in technical documentation. Clear technical advantages explained for practical decision‑making The 0.8 mm corner radius strengthens the cutting edge and improves resistance to edge chipping during interrupted cuts, while the chipbreaker design shapes the chip to limit heat concentration and machine wear. These characteristics translate into fewer tool changes and more stable process windows on CNC milling centres. The insert’s coded thickness and plate size are supplied as specified; for exact workpiece compatibility and cutting data, please consult the product matrix—the material suitability must be checked against the specific application. This pragmatic overview supports selection decisions in job shops and volume production alike. Reliability, brand backing and application orientation Walter Tools’ engineering pedigree ensures the insert is manufactured to tight tolerance standards and designed for repeatable performance in demanding machining scenarios. The combination of coated carbide, a proven chip control geometry and a moderate relief angle delivers a tool solution that favours longer edge life and consistent part quality. For manufacturers seeking process stability and predictable tool behaviour, this variant offers a technically clear, application‑oriented option that integrates into existing tool systems with familiar handling and indexable insert workflows. Contact Metav Werkzeuge to discuss suitability for specific materials and to arrange supply of ZDGT200508R-K85 WNN15 inserts with tailored cutting data and delivery options Technical data Article number: ZDGT200508R-K85-WNN15-WALTER Designation: ZDGT200508R-K85 WNN15 Product type: Milling indexable insert (Fräswendeschneidplatte) Manufacturer: Walter Tools Execution code: T Series: Walter Schneidstoffsorte - Serie offen Specifications Relief angle: 15° Corner radius: 0.8 mm Plate size: 20 Thickness: 05 Tolerance class: G Features Grade: WNN15 (coated carbide / beschichtetes Hartmetall) Chipbreaker: K85 Material specification: catalogue-dependent Series description: WNN15 is a Walter grade; verify workpiece suitability via product matrix FAQ What materials is this insert suitable for? Material suitability should be checked against the product matrix; the WNN15 grade is a coated carbide designed for a broad range of applications, but specific workpiece compatibility must be verified for the intended machining task. How does the chipbreaker K85 affect performance? The K85 chipbreaker shapes and breaks chips to improve evacuation and reduce heat build-up, leading to more stable cutting conditions and fewer interruptions for chip removal when using ZDGT200508R-K85 WNN15 inserts. What does the 0.8 mm corner radius mean for milling results? A 0.8 mm corner radius increases edge robustness and resistance to chipping during interrupted cuts, which helps maintain surface quality and prolong tool life under mixed cutting conditions. Is the relief angle fixed and what is its benefit? The relief angle is 15°, which balances cutting aggressiveness with edge strength to provide versatile performance across a variety of milling operations. Where can further cutting data be obtained for this insert? Cutting parameters and application guidance are available from Metav Werkzeuge; consult the technical documentation and product matrix to match ZDGT200508R-K85 WNN15 to the specific machine, holder and workpiece material. Manufacturer: Walter Tools; Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT200512R-K85 WK10 Wendeplatten - Walter Tools
The combination of WK10 uncoated carbide and the K85 chipbreaker delivers consistent chip control and reliable cutting performance; coupled with a 1.2 mm corner radius and 15° clearance, this insert supports stable milling cycles and predictable tool life. Order directly via Metav Werkzeuge or consult our advisers for specification checks and availability. ZDGT200512R-K85 WK10 milling indexable insert by Walter Tools The ZDGT200512R-K85 WK10 is a milling indexable insert designed for general milling operations where robust chip control and repeatable edge performance are required. Walter WK10 uncoated carbide grade K85 chipbreaker for reliable chip control 15° clearance angle for smooth entry 1.2 mm corner radius for robust edges Precision grade for dependable material removal Manufactured in the Walter WK10 grade, this insert combines uncoated carbide properties with a dedicated K85 chipbreaker to enhance chip formation and evacuation. The result is improved process stability and a more consistent surface finish compared with less optimised geometries. In practice, the optimised chip control reduces the need for frequent manual clearing and helps maintain cycle times — a direct benefit for workshops pursuing higher throughput with fewer interruptions. Suitability for specific workpiece materials should be verified using the product matrix supplied by Walter Tools. Geometry engineered to reduce tool changes and downtime The insert’s 15° clearance angle and 1.2 mm corner radius provide a balance between edge robustness and accessibility in interrupted cuts. These design choices lower the risk of premature chipping and extend the interval between indexings, supporting steady production flow. With a nominal inscribed circle of 20 mm and a plate thickness of 0.5 mm, the component offers compact geometry for use in modular milling cutters where small form factors are required without compromising strength. The tolerance class G further ensures consistent fitment and interchangeability in standard toolholders. Workshop integration and manufacturing benefits As part of the Walter open series, this insert is intended for straightforward integration into existing milling systems that accept the ZDGT style insert. The K85 chipbreaker is tuned to promote predictable swarf behaviour, which in turn supports automated or semi-automated material handling downstream. Clear, repeatable seating and indexing reduce setup variability and support quality assurance processes. For materials guidance, note that the grade and series are described as catalogue-dependent; therefore the precise material suitability must be checked in the manufacturer’s matrix to match the machining strategy and achieve the best performance. For technical compatibility checks, stock confirmation or to request cutting data for Walter Tools WK10 inserts, contact Metav Werkzeuge for tailored advice and rapid procurement. Technical data Article number: ZDGT200512R-K85-WK10-WALTER Designation: ZDGT200512R-K85 ISO designation: ZDGT200512R-K85 WK10 Product type: Fräswendeschneidplatte (milling indexable insert) Manufacturer: Walter Tools Core specifications Free angle: 15° Corner radius: 1.2 mm Inscribed circle / size: 20 mm Thickness: 0.5 mm Tolerance class: G Materials and special features Grade: WK10 (uncoated carbide) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Execution: T Recommendation: Check suitability using the product matrix FAQ What material is the WK10 grade intended for? The WK10 grade is an uncoated carbide formulation; material suitability for the ZDGT200512R-K85 WK10 insert should be checked using Walter Tools’ product matrix for precise recommendations. How does the K85 chipbreaker influence machining? The K85 chipbreaker in this insert promotes controlled chip formation and evacuation, improving process security and reducing the likelihood of chip-related interruptions during milling. What does the designation ZDGT200512R-K85 indicate? The designation describes the insert geometry and features: the ZDGT form, the size parameters, right-hand orientation (R), and the fitted K85 chipbreaker, as used by Walter Tools. Can this insert be used in small-diameter modular cutters? With an inscribed circle of 20 mm and a thickness of 0.5 mm, the insert suits compact cutter systems designed for ZDGT-style plates; compatibility should be confirmed against the cutter manufacturer’s specifications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is part of the Sandvik group. Protected trademarks and trade names remain the property of their respective owners and are mentioned here for identification purposes only. There is no partnership between our company and the named brands; the offered item is an original, factory-new product of the listed manufacturer.
ZDGT200516R-K85 WK10 T Wendeplatten - Walter Tools
Reliable machining performance is achieved by combining the WK10 uncoated carbide grade with the K85 chipbreaker and a 15° relief, delivering stable chip formation and reproducible results; order directly via Metav Werkzeuge or request specialist advice from our consultants. ZDGT200516R-K85 WK10 milling indexable insert by Walter Tools — uncoated carbide, 15° relief A versatile ZDGT200516R-K85 WK10 milling insert designed for general milling operations where controlled chip flow and consistent surface quality are required. Uncoated carbide grade WK10, robust cutting edge 15° relief angle for secure cutting geometry 1.6 mm corner radius for repeatable finishes K85 chipbreaker for controlled chip formation Efficient cutting through stable chip control and productivity The combination of the WK10 substrate and the K85 chipbreaker supports stable chip formation, which reduces interruptions caused by tangled or long chips and improves machine uptime. The insert’s uncoated carbide composition is intended for demanding machining cycles where a reliable cutting edge and predictable wear behaviour are priorities. This results in higher process efficiency and more consistent cycle times, making the product suitable for workshops seeking measurable improvements in throughput and tool-life stability. Geometry that promotes surface quality and dimensional constancy A 15° relief angle and a 1.6 mm corner radius contribute directly to improved component finish and repeatable geometrical accuracy. The relief angle reduces rubbing on the flank, lowering heat generation at the cutting edge, while the corner radius evens out local cutting forces to minimise micro-chatter. Together these features support a consistent surface finish and reduce the need for secondary finishing operations, which in turn lowers overall production effort and time per workpiece. Practical integration and selection guidance for reliable results The insert is supplied in the series Series: Walter Schneidstoffsorte - Serie offen and carries tolerance class G, which facilitates predictable clamping and interchangeability in standard milling toolholders. The designation and execution code reflect industry-standard format and should be cross-checked with the machine setup and the product matrix for optimal grade selection. For specialised materials or unusual process demands, consult the product matrix to confirm suitability and to identify alternative grades if required. The ZDGT200516R-K85 WK10 insert is engineered to support stable cutting processes in repetitive production environments. For tailored recommendations or a delivery quote concerning Walter Tools inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for technical clarification and ordering support Technical data Article number: ZDGT200516R-K85-WK10-WALTER Designation: ZDGT200516R-K85 WK10 Manufacturer: Walter Tools Product type: Fräswendeschneidplatte / milling indexable insert Facts Relief angle: 15° Corner radius: 1.6 mm Plate size: 20 Plate thickness code: 05 Special features Chipbreaker: K85 Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T Tolerance: G FAQ What materials is this insert intended for? The WK10 grade is an uncoated carbide designed for a range of machining tasks; verify the material suitability for the ZDGT200516R-K85 WK10 insert against the product matrix before use. How does the K85 chipbreaker affect machining? The K85 chipbreaker on the ZDGT200516R-K85 WK10 insert promotes controlled chip formation, reducing the risk of chip entanglement and improving process stability. Is the corner radius suitable for finishing operations? A 1.6 mm corner radius balances tool strength with surface quality, supporting good finishes while maintaining edge robustness for repetitive milling tasks. What does tolerance class G mean for toolholders? Tolerance class G indicates the manufacturing tolerance standard of the insert, which helps ensure consistent clamping fit and repeatable positioning in compatible toolholders. Are there restrictions for high-speed cutting? The uncoated carbide WK10 provides predictable wear behaviour; for very high cutting speeds or specialised alloys, consult the product matrix or contact Metav Werkzeuge for grade alternatives. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT200520R-K85 WK10 Wendeplatten - Walter Tools
The combination of the WK10 uncoated carbide grade with a K85 chipbreaker and a 15° relief angle delivers stable chip control and consistent surface quality in finishing operations; benefit from predictable tool life and repeatable results. Order the insert directly via Metav Werkzeuge or request application advice from the consultants if clarification is required. ZDGT200520R-K85 WK10 — Walter Tools milling indexable insert, K85 chipbreaker, 15° relief The ZDGT200520R-K85 WK10 is a milling indexable insert intended for controlled chip formation and reliable finishing tasks across a broad range of applications. Uncoated carbide grade WK10 K85 chipbreaker for secure chip control 15° relief angle reduces cutting forces Corner radius 2 for consistent surface finish Improved productivity through controlled chip formation The insert uses an uncoated carbide grade WK10 combined with the K85 chipbreaker to promote consistent chip breaking and evacuation. That combination helps reduce the risk of built-up edge and allows for reliable cutting under varying feeds and depths. The moderate 15° relief angle lowers cutting forces, which contributes to smoother power draw and can reduce vibrations in less rigid set-ups. For process planners, this translates into steadier cycle times and better repeatability when machining components that demand consistent surface quality. Precision finishing and surface integrity with a defined corner radius A defined corner radius of 2 supports a predictable transition between passes and reduces the occurrence of chatter marks in finishing cuts. The geometry is suited to operations where surface integrity matters: the insert delivers a balance between edge strength and fine surface generation. Where the application requires explanation of terms, the corner radius denotes the rounded edge at the insert tip that influences scallop height and micro-roughness; a 2 radius typically gives improved finish while maintaining adequate edge robustness. Practical guidance for selection and integration The insert is provided in a manufacturer coding system (size code 20, thickness code 05, execution T) and must be matched to the cutter body and seat geometry. Material suitability is not universal — the product matrix from Walter Tools should be consulted to confirm optimal cutting parameters and recommended workpiece materials. For customers planning process changes, the geometry and chipbreaker support conservative parameter windows for safe implementation and reduce the need for repeated trial cuts. Discuss the ZDGT200520R-K85 WK10 with Metav Werkzeuge for tailored application advice—email info@metav-werkzeuge.com or call +49 2822 7131930 for a detailed consultation. Technical Data Article number: ZDGT200520R-K85-WK10-WALTER Designation: ZDGT200520R-K85 WK10 Product type: milling indexable insert Manufacturer: Walter Tools Specifications Relief angle: 15° Corner radius: 2 Insert size code: 20 Thickness code: 05 Chipbreaker: K85 Tolerance class: G Materials & Special features Carbide grade: WK10 (uncoated) Series: Walter Schneidstoffsorte - Serie offen Execution: T Note: Check product matrix for material suitability FAQ What materials is this insert suitable for? Material suitability should be verified in the Walter Tools product matrix; the WK10 grade is an uncoated carbide and may cover a broad range, but checks for specific alloys are required. Is WK10 a coated grade? No, WK10 is specified as an uncoated carbide grade in the product information for the ZDGT200520R-K85 WK10 insert. What is the purpose of the K85 chipbreaker? The K85 chipbreaker is designed to shape and control chips during milling, promoting reliable evacuation and helping to protect the cutting edge for consistent surface quality. Which codes identify the insert size and thickness? The insert is designated with size code 20 and thickness code 05; full identification is ZDGT200520R-K85-WK10-WALTER. How to ensure compatibility with a cutter body? Compatibility depends on seat geometry and clamping style; match the insert coding and execution T with the cutter body specifications and consult the Walter Tools documentation or the product matrix. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Mark names and protected designations are used solely for explanation and identification; there is no connection between our company and the named brands. The offered article is original, factory-new goods of the manufacturer.
ZDGT200520R-K85 WNN15 WNN15 Wendeplatten - Walter Tools
Take advantage of the K85 chipbreaker and the 2 mm corner radius for stable chip control and longer edge life; combine this with the 15° relief angle for consistent cutting geometry — order the insert via Metav Werkzeuge or request tailored cutting data from the consultants. ZDGT200520R-K85 WNN15 — indexable milling insert, K85 chipbreaker, 15° relief (Walter Tools) The ZDGT200520R-K85 WNN15 is an indexable milling insert designed for versatile metal machining applications, combining a coated-carbide grade with a K85 chipbreaker to support controlled chip evacuation and reliable performance. Coated carbide grade WNN15 for general machining K85 chipbreaker for reliable chip control 15° relief angle for stable cutting geometry 2 mm corner radius for robust edge strength Consistent cutting performance for mixed-material production The insert is based on a coated carbide grade that aims to deliver stable chip formation and broad workpiece coverage. The WNN15 grade is engineered for general machining tasks where a balance between wear resistance and toughness is required; this results in more predictable tool behaviour across varying batches. Using a defined chipbreaker geometry reduces the risk of irregular chips, which in turn supports continuous production and fewer interruptions for manual chip clearing. The design therefore supports higher uptime in milling operations and helps to maintain surface quality without frequent insert changes. Built-in durability and precise edge geometry for longer tool life A 2 mm corner radius together with the specified 15° relief angle produces a robust cutting edge that resists chipping under moderate loads and promotes even wear distribution. The K85 chipbreaker further contributes to controlled cutting forces and reduced vibrations, which benefits both component finish and insert lifetime. For process planners this combination means more consistent cycle times and improved repeatability when set-up data are transferred between machines; the geometry supports a favourable compromise between strength and sharpness for typical finishing and semi-finishing passes. Practical application and integration into production workflows As an indexable milling solution, the insert fits established toolholders that accept the ZDGT geometry and enables quick indexing to restore a fresh cutting edge. The ZDGT200520R-K85 WNN15 is supplied in a standard form factor that eases inventory handling and simplifies tool selection for production engineers. Material suitability should be verified against the supplier’s product matrix, but the coated-carbide class and chipbreaker design make the insert a practical choice for mixed-material shops seeking predictable chip control and straightforward integration into existing milling tool systems. For machining tasks that demand reliable chip control and extended edge life, contact Metav Werkzeuge for specific cutting parameters, availability and technical consultation regarding the Walter Tools ZDGT200520R-K85 WNN15 insert. Technical data SKU: ZDGT200520R-K85-WNN15-WALTER Article designation: ZDGT200520R-K85 Product label: Fräswendeschneidplatte ZDGT200520R-K85 WNN15 Walter Tools Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 2 mm Plate size: 20 mm Plate thickness: 05 Special features Grade: WNN15 (coated carbide) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material designation: Katalogabhängig Tolerance class: G ISO designation: ZDGT200520R-K85 WNN15 FAQ What materials is the insert suited for? The WNN15 graded insert is a coated carbide type; material suitability should be checked against the supplier product matrix for specific workpiece materials. How does the K85 chipbreaker benefit milling operations? The K85 chipbreaker on the ZDGT200520R-K85 WNN15 insert promotes reliable chip control and reduced vibration, supporting consistent surface quality and longer edge life. What does the 2 mm corner radius mean for component finish? A 2 mm corner radius provides a robust edge that limits chipping and helps maintain stable cutting conditions, which contributes to uniform finishing results. Is this insert compatible with standard ZDGT toolholders? The ZDGT200520R-K85 WNN15 follows the ZDGT ISO designation and is intended for use in matching ZDGT indexable-milling toolholders. How should the WNN15 grade be selected for production runs? Selection of the WNN15 grade should be based on the product matrix and the specific mix of materials in the production process to balance tool life and surface requirements. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT200530R-K85 WK10 T Wendeplatten - Walter Tools
Robust uncoated carbide WK10 combined with the K85 chipbreaker and a 15° clearance angle delivers stable swarf control and consistent edge life for reliable milling operations; order inserts directly via Metav Werkzeuge or consult our specialists for application-specific advice. ZDGT200530R-K85 WK10 — Walter Tools milling indexable insert, K85 chipbreaker, 15° clearance The ZDGT200530R-K85 WK10 is a milling indexable insert engineered for controlled chipbreaking and consistent finishing in medium-duty milling applications. Uncoated carbide grade WK10 K85 chipbreaker for controlled swarf 15° clearance angle for smooth cutting 3 mm corner radius for robust edge strength Predictable performance through material and geometry The uncoated WK10 grade is designed for a balance of toughness and productive cutting; combined with the K85 chipbreaker, it promotes stable chip formation and reduces the risk of built-up edge in a range of operations. The geometry coded by ZDGT200530R-K85 and the 15° clearance angle contribute to lower cutting forces and a more consistent contact pattern between insert and workpiece, which in turn supports repeatable results on conventional milling setups. Clear advantages for surface quality and tool life A 3 mm corner radius and the specified tolerance class G help protect the cutting edge under intermittent cutting and light finishing passes, resulting in improved surface finish and predictable wear progression. While the grade is an uncoated carbide, its mechanical properties make it suitable for cost-conscious operations where stable edge behaviour and straightforward regrinding or replacement strategies are preferred. For exact material suitability, refer to the manufacturer’s product matrix to match the insert to the specific workpiece material. Installation, compatibility and process stability The insert’s ISO designation and series information simplify the selection of compatible toolholders and clamping systems; the execution code provides guidance for correct seat fitment and orientation. The modest clearance angle and the K85 chipbreaker reduce vibration sensitivity in many cutter assemblies, supporting higher process reliability and less frequent intervention for insert changes. Tolerance class G supports interchangeability across standardised tool lines. Practical use cases and selection advice This insert is positioned for general finishing and soft roughing tasks where consistent chip control and edge robustness are priorities. The open-series Walter grade is uncoated, which can be advantageous in operations that favour mechanical toughness over high-temperature resistance. For specialised materials or demanding high-speed operations, consult the Walter technical matrix to confirm the grade and chipbreaker match the machining strategy. Contact Metav Werkzeuge for application advice and to order Walter Tools ZDGT200530R-K85 WK10 inserts directly; please quote SKU ZDGT200530R-K85-WK10-WALTER — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: ZDGT200530R-K85-WK10-WALTER ISO designation: ZDGT200530R-K85 WK10 Manufacturer: Walter Tools Numbers / Core technical data Plate size: 20 Corner radius: 3 mm Clearance angle: 15° Plate thickness code: 05 Tolerance class: G Special features / Material & versions Chipbreaker: K85 Grade: WK10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T FAQ What is the primary function of this insert? The insert is a milling indexable insert intended for controlled chipbreaking and consistent finishing; the ZDGT200530R-K85 WK10 combines the K85 chipbreaker with a WK10 uncoated carbide grade for stable swarf control. Which materials is the WK10 grade suitable for? The WK10 grade is an uncoated carbide suited to a broad range of general machining tasks; specific suitability should be checked against the Walter Tools product matrix for exact workpiece materials. How does the K85 chipbreaker affect machining? The K85 chipbreaker promotes predictable chip formation and evacuation, which helps maintain process stability and can improve surface quality during finishing passes. How important is the 15° clearance angle? A 15° clearance angle reduces rubbing on the flank face and contributes to smoother cutting action, which benefits surface finish and helps moderate cutting forces in many milling applications. Is the insert compatible with standard ISO toolholders? The ISO designation ZDGT200530R-K85 indicates geometry and seat form that are compatible with standard clamping systems designed for this insert family; verify holder compatibility by matching the ISO code. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany; www.walter-tools.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT200530R-K85 WNN15 WNN15 Wendeplatten - Walter Tools
Take advantage of the combination of WNN15 coated carbide, the K85 chipbreaker and the 15° relief geometry for consistent chip control and predictable tool life; order the ZDGT200530R-K85 WNN15 directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. ZDGT200530R-K85 WNN15 indexable milling insert — Walter Tools, K85 chipbreaker, 15° relief ZDGT200530R-K85 WNN15 is an indexable milling insert designed for productive milling operations where stable chip formation and repeatable edge life are required Coated carbide grade WNN15 K85 chipbreaker for stable chip control 15° relief angle for versatile milling Corner radius R3 for reliable edge strength Engineered for stable chip formation and higher productivity The insert is based on the WNN15 coated carbide grade and is shaped to promote stable chip formation under a wide range of cutting conditions. The integrated K85 chipbreaker optimises chip flow during interrupted and continuous cuts, reducing the risk of built-up edge and improving process reliability. By combining a wear-resistant coating with a balanced geometry, this solution aims to extend the tool life and maintain consistent component quality, which supports higher effective productivity in series production. Geometry that balances strength and surface finish A 15° relief angle and a corner radius R3 provide a compromise between cutting edge strength and achievable surface finish. The moderate relief angle contributes to lower cutting forces in many milling operations, while the R3 corner increases resistance to chipping on entry and exit. This geometry is particularly useful when machining with variable engagement or when surface quality and dimensional repeatability are priorities, allowing operators to obtain consistent results with fewer insert changes. Coating and grade explained — what WNN15 delivers The WNN15 designation indicates a coated carbide grade optimised for a broad range of materials; the coating improves wear resistance and thermal stability at the cutting zone. The specific substrate and coating stack are catalog-dependent, so the final composition and recommended cutting parameters should be checked in the product matrix. The combination of coating and K85 chip control is intended to reduce downtime for regrinding and replacement, contributing to lower process costs over the tool life. Practical integration and recommendations for use The insert is supplied in the ZDGT geometry and is intended for mounting in compatible indexable milling cutters that accept this ISO-style designation. Tolerance class G ensures dimensional consistency for repeatable indexation and balance. For best results, match the insert to the appropriate cutter body and consult the product matrix for recommended cut data; if material suitability or cutting parameters are unclear, Metav Werkzeuge can provide application advice to align the insert’s strengths with the machining task. Contact Metav Werkzeuge for tailored selection and to secure Walter Tools ZDGT200530R-K85 WNN15 inserts — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data SKU: ZDGT200530R-K85-WNN15-WALTER Designation: ZDGT200530R-K85 WNN15 Product type: indexable milling insert Brand: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Grade: WNN15 Execution: T Tolerance class: G Facts Relief angle: 15° Corner radius: 3 Plate size: 20 Plate thickness: 05 Chipbreaker: K85 Special features Coated carbide (beschichtetes Hartmetall) K85 chipbreaker for stable chips Catalog-dependent substrate material Check product matrix for material suitability Designed for ZDGT insert holders Tolerance class G for repeatable indexation FAQ Which materials is this insert suitable for? The ZDGT200530R-K85 WNN15 insert is a coated carbide grade intended for a broad range of materials; specific suitability should be verified in the product matrix for the WNN15 grade. What benefit does the K85 chipbreaker provide? The K85 chipbreaker on the Walter Tools insert promotes controlled chip formation and evacuation, reducing build-up and improving process stability during interrupted and continuous milling. Why is the R3 corner radius important? A corner radius of 3 increases edge strength and resistance to chipping, which helps achieve more reliable tool life and consistent surface quality with the ZDGT geometry. Can this insert be used in standard ZDGT holders? The insert is supplied with the ISO-style designation ZDGT200530R-K85 and is intended for compatible ZDGT holders; correct mounting and clamp type should be checked against the cutter body. How is the coating specified for this grade? Coating and substrate details are catalog-dependent for the WNN15 grade; consult the product matrix or Metav Werkzeuge for the definitive coating specification and recommended cutting data. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and do not imply any affiliation between our company and the listed manufacturers. The offered item is an original, factory-new product of the respective brand (Walter Tools).
ZDGT200540R-K85 WK10 T Wendeplatten - Walter Tools
Take advantage of the combination of WK10 uncoated carbide, the K85 chipbreaker and a compact r4 corner radius for stable, repeatable milling results; order directly via Metav Werkzeuge or consult our specialists for process support. ZDGT200540R-K85 WK10 — Milling indexable insert with K85 chipbreaker, r4, 15° — Walter Tools A ZDGT200540R-K85 WK10 milling indexable insert designed for reliable chip control and economical machining in general milling applications. WK10 uncoated carbide grade K85 chipbreaker for stable chips r4 corner radius for versatile edge strength 15° clearance angle for controlled engagement Consistent chip management for stable processes The combination of the K85 chipbreaker and the WK10 uncoated carbide grade is engineered to produce predictable chip shapes and reduced cutter load variation. Stable chips lower the risk of re-cutting and reduce machine downtime, which contributes directly to higher productivity in serial milling. The insert’s geometry, including the r4 corner radius, balances edge strength and form accuracy, enabling smoother engagement at a recommended 15° clearance. This results in fewer interruptions and a more consistent surface finish when compared with less optimised geometries. Clear technical benefits that improve throughput Built for dependable performance, the insert’s key dimensions and features promote efficient material removal while preserving tool life. The uncoated carbide substrate of the WK10 grade provides a cost-effective option where high-temperature coatings are not required, and the chipbreaker profile reduces the tendency for long, stringy chips in many machining scenarios. Where process reliability and predictable wear patterns are priorities, the insert supports stable cutting conditions that help maintain cycle times and reduce secondary operations caused by poor chip control. Easy identification and integration into existing toolsets The insert is supplied under the designation ZDGT200540R-K85 and is compatible with standard indexable milling holders that accept this form factor. Its compact plate size and defined corner radius make it suitable for a range of pocketing and face-milling tasks where a medium edge strength and good versatility are required. For planning purposes, consult the manufacturer’s product matrix for specific workpiece-material recommendations; where precise matching of insert grade to component material is essential, the WK10 grade should be cross-checked against the intended application to ensure optimal outcomes. For reliable milling using the proven WK10 grade and K85 chipbreaker, contact Metav Werkzeuge for availability and application advice — Metav Werkzeuge can support selection and supply directly. Technical data Article number: ZDGT200540R-K85-WK10-WALTER ISO designation: ZDGT200540R-K85 WK10 Manufacturer: Walter Tools Facts Free angle: 15° Corner radius: 4 Plate size: 20 Plate thickness: 05 Tolerance class: G Special features Grade: WK10 (uncoated carbide) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Execution: T FAQ What materials is this insert intended for? The WK10 grade in the ZDGT200540R-K85 WK10 insert is an uncoated carbide type; specific workpiece suitability should be verified against the product matrix to ensure the grade matches the intended material and machining strategy. How does the K85 chipbreaker improve performance? The K85 chipbreaker is designed to form short, controllable chips, reducing the chance of chip entanglement and improving machining stability when using the ZDGT200540R-K85 insert. What advantages does the r4 corner radius provide? An r4 corner radius increases edge strength and helps absorb cutting forces during interrupted cuts, offering a balance between robustness and achievable surface finish for many milling operations. Is the free angle important for cutter engagement? Yes, the 15° free angle affects tool-workpiece contact and the load on the cutting edge; this geometry supports controlled penetration and contributes to consistent cutting conditions. How can the correct insert be identified for an application? Refer to the ISO designation ZDGT200540R-K85 WK10 and compare the grade, chipbreaker and radius to the machining requirements; Metav Werkzeuge can assist with matching the insert to specific applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original factory-new goods of the manufacturer.
ZDGT200540R-K85 WNN15 Wendeplatten - Walter Tools
Take advantage of the combination of a coated carbide grade (WNN15), a K85 chipbreaker and a 15° clearance for reliable chip control and productive milling performance; order the insert directly via Metav Werkzeuge or consult the technical advisers for application-specific recommendations. ZDGT200540R-K85 WNN15 – Indexable milling insert, coated carbide, K85 chipbreaker (Walter Tools) The ZDGT200540R-K85 WNN15 is an indexable milling insert developed for productive face and profile milling applications, offering a coated carbide grade for broad material coverage and stable chip formation. Coated carbide WNN15 for wide material range K85 chipbreaker for controlled chip formation 15° clearance for versatile milling applications Corner radius 4 for balance of strength and finish Engineered for productive, predictable cutting The insert is built around the WNN15 coated carbide grade and the K85 chipbreaker, which together enable consistent chip control and efficient material removal. The coating reduces wear, extending tool life under many machining conditions, while the chipbreaker shapes chips to improve evacuation and reduce rework caused by tangling. For production environments this translates into fewer stoppages and steadier cycle times. The insert’s geometry supports reliable cutting forces and contributes to a smoother workflow on milling machines. Improved surface finish and tool longevity A 15° clearance combined with a corner radius of 4 helps achieve a compromise between cutting-edge strength and surface quality. The clearance angle reduces rubbing on the flank face, lowering heat build-up and minimising abrasion, while the corner radius distributes cutting loads to resist chipping. This results in a more consistent surface finish and longer intervals between indexings or insert changes, helping to reduce overall tooling costs without sacrificing component quality. Simple integration and verified material guidance The ISO designation and series information facilitate correct selection and mounting in standard toolholders; refer to the product matrix to confirm suitability for specific alloys. The insert carries the ISO marking ZDGT200540R-K85 WNN15, simplifying procurement and replacement. Because the material specification is catalogue-dependent, it is advisable to check the detailed product matrix for optimal cutting parameters for each workpiece material. This step ensures the insert is matched to both the machining strategy and the chosen workpiece metallurgy. Process security and shop-floor benefits The geometry and grade are designed for stable chip formation and repeatable performance, contributing to predictable tool life and reduced scrap rates. Reliable chip control and the coated substrate help protect adjacent components from scatter and minimise manual chip clearing. The combination of stable cutting behaviour and clear ISO identification supports fast decision-making in production planning and tool management, strengthening overall process security and productivity. For process-proven milling performance with Walter Tools' coated grade WNN15 and the K85 chipbreaker, contact Metav Werkzeuge for technical advice and stock availability of the ZDGT200540R-K85 WNN15 insert. Technical Data SKU: ZDGT200540R-K85-WNN15-WALTER Article: ZDGT200540R-K85 WNN15 Product type: Indexable milling insert (Fräswendeschneidplatte) Manufacturer: Walter Tools Facts Clearance angle: 15° Corner radius: 4 Plate size: 20 Plate thickness: 05 Tolerance class: G Special features Grade: WNN15 (coated carbide) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen ISO designation: ZDGT200540R-K85 WNN15 Execution: T Material specification: Katalogabhängig FAQ What materials is the ZDGT200540R-K85 WNN15 suited for? The ZDGT200540R-K85 WNN15 insert uses the WNN15 coated carbide grade and is intended for a broad material range; consult the product matrix to determine suitability for specific steels, alloys and non-ferrous materials. How does the K85 chipbreaker affect machining? The K85 chipbreaker on the ZDGT200540R-K85 WNN15 shapes and breaks chips to improve evacuation and reduce recutting, which supports stable cutting and fewer interruptions during milling cycles. What are the dimensional key points to check when ordering replacements? Ensure the ISO designation ZDGT200540R-K85 WNN15, the plate size (20), plate thickness (05) and the corner radius (4) match the holder and application to guarantee proper seating and performance. Is the WNN15 grade a coated or uncoated carbide? WNN15 is specified as a coated carbide grade; the coating enhances wear resistance and helps maintain the cutting edge under typical milling conditions. How does the 15° clearance improve operation? A 15° clearance reduces flank contact, lowering heat and abrasive wear while maintaining cutting efficiency, which helps achieve consistent surface quality and longer insert life with the ZDGT200540R-K85 WNN15. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the brands named. The offered article is original, factory‑new goods of the manufacturer.
ZDGT200550R-K85 WK10 Wendeplatten - Walter Tools
Take advantage of the WK10 uncoated carbide and the K85 chipbreaker with a 15° relief angle for productive milling and consistent surface quality; order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. ZDGT200550R-K85 WK10 milling indexable insert, K85 chipbreaker, 15° — Walter Tools The ZDGT200550R-K85 WK10 is a milling indexable insert designed for versatile finishing and general-purpose milling, combining a K85 chipbreaker with a 15° relief for stable cutting performance. Uncoated carbide grade WK10 K85 chipbreaker for improved chip control 15° relief angle for consistent surface finish Robust indexable geometry ZDGT200550R-K85 Consistent surface quality and process stability The WK10 grade is an uncoated carbide designed for reliable, repeatable performance across a broad range of tasks. Its composition gives a stable cutting edge, which helps to maintain surface finish in cyclic machining operations. The 15° relief reduces rubbing on the flank, lowering cutting forces during finishing passes and supporting predictable results even under changing conditions. For production environments this means fewer scrapped parts and more consistent batch quality. Efficient chip control that reduces downtime The integrated K85 chipbreaker is tailored to form short, controllable chips in typical milling conditions. Improved chip formation enhances evacuation from the cutting zone, which in turn reduces the risk of re-cutting and tool damage. The combination of geometry and chipbreaker promotes continuous cutting and minimises unplanned interruptions, contributing to higher process uptime and more economical cycle times on shoulder and face milling applications. Practical selection guidance and material considerations Selection should follow the tool matrix and the intended workpiece material; the insert is supplied in the Walter open-series for flexible application. The spare geometry ZDGT200550R-K85 supports common clamping systems and simple indexing, which aids quick replacements and tool management. When used in line with application data, the insert offers an effective balance between edge robustness and productivity, making it suitable for a range of standard finishing and light roughing tasks. Contact Metav Werkzeuge for tailored application support and to supply genuine Walter Tools inserts directly from stock — Metav Werkzeuge is available for technical consultation and order processing Technical data Article number: ZDGT200550R-K85-WK10-WALTER Label: Fräswendeschneidplatte ZDGT200550R-K85 WK10 Walter Tools Product type: Fräswendeschneidplatte Numbers / Core technical data Free angle: 15° Corner radius: 5 Plate size: 20 Plate thickness: 05 Tolerance class: G Designs / Special features Chipbreaker: K85 Grade: WK10 Series: Walter Schneidstoffsorte - Serie offen Execution: T Base designation: ZDGT200550R-K85 Material: Katalogabhängig ISO designation: ZDGT200550R-K85 WK10 Manufacturer: Walter Tools FAQ What materials is this insert intended for? The ZDGT200550R-K85 WK10 insert is provided in a Walter open series; material suitability should be checked against the specific product matrix, with WK10 typically used where an uncoated carbide performs well. How does the K85 chipbreaker improve machining? The K85 chipbreaker on this insert promotes short, controllable chips and better evacuation, which reduces the chance of re-cutting and supports continuous milling operations. Is the relief angle important for finishing? Yes — the 15° relief angle reduces flank contact and cutting forces during finishing, helping to deliver a consistent surface finish and stable process behaviour. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Walter Tools: The Walter AG (brand Walter Tools) with headquarters in Tübingen is among the world's leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, brand-new product from the manufacturer.
ZDGT200550R-K85 WNN15 WNN15 Wendeplatten - Walter Tools
Take advantage of a robust combination of stable chip formation and proven coated-carbide performance for reliable milling results. The WNN15 grade and K85 chipbreaker deliver consistent chip control and predictable wear behaviour, helping to maintain productivity; order this insert directly via Metav Werkzeuge or consult our specialists for application support. ZDGT200550R-K85 WNN15 milling indexable insert – 15° relief, K85 chipbreaker (Walter Tools) ZDGT200550R-K85 WNN15 is a coated carbide milling insert suitable for industrial milling applications, designed to provide controlled chips and consistent edge life Coated carbide grade WNN15 for general use 15° relief angle for reliable entry and stability K85 chipbreaker for controlled chip formation Series: Walter Schneidstoffsorte – Serie offen Controlled chip formation for process stability The insert is engineered for consistent chip control, thanks to the integrated K85 chipbreaker and the coated-carbide WNN15 grade. For milling processes where predictable chips reduce downtime and improve surface quality, the chipbreaker geometry separates and evacuates material efficiently, lowering the risk of built-up edge and tool jamming. In practise, this means fewer interruptions in production and a steadier cycle time when compared with unguided chip profiles. Precision geometry that supports repeatable tool life A defined 15° relief angle combined with the specified cutting-edge geometry contributes to extended tool life and repeatable cutting behaviour. The relief angle reduces friction on the flank face during cutting, which helps to maintain the cutting edge and stabilise cutting forces. For operators monitoring tooling costs and machine uptime, this geometry helps to balance wear and performance across batches of identical inserts, enabling predictable reconditioning or replacement intervals. Material compatibility and application guidance The insert is supplied in the Walter WNN15 coated-carbide grade; users should verify the exact material suitability against the product matrix for specific workpiece materials. Coated carbide typically performs well across a broad range of steels and cast alloys when matched to appropriate cutting data. For applications requiring improved surface finish or where chip control is critical, the combination of the WNN15 coating characteristics and K85 chipbreaker supports finishing and semi-finishing operations under stable machining parameters. Handling, indexing and practical benefits on the shop floor As an indexable insert, the part facilitates quick edge changes without the need to replace an entire cutter body, reducing setup time and waste. The defined geometry and series designation support simple tool assembly and inventory management in toolrooms that standardise on Walter Tools inserts. For maintenance planning, the predictable wear pattern simplifies decisions on regrinding, indexing or replacement, aiding both production planning and cost accounting. For tailored advice on the Walter Tools ZDGT200550R-K85 WNN15 milling insert and to discuss suitability for specific materials or machining strategies, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: ZDGT200550R-K85-WNN15-WALTER Designation: ZDGT200550R-K85 WNN15 Product type: Milling indexable insert Manufacturer: Walter Tools Grade / Series: WNN15 — Walter Schneidstoffsorte - Serie offen Execution: T Tolerance class: G Core dimensions Relief angle: 15° Chipbreaker: K85 Corner radius: 5 Plate size: 20 Plate thickness: 05 Materials & special features Coated carbide (WNN15) Controlled chip formation via K85 chipbreaker Series note: Check product matrix for workpiece suitability FAQ What machining tasks is this insert best suited for? The ZDGT200550R-K85 WNN15 insert is designed for milling operations where controlled chip formation and reliable edge life are required; the K85 chipbreaker and WNN15 grade support finishing and semi-finishing tasks. How does the 15° relief angle affect performance? A 15° relief angle reduces flank contact and friction during cutting, which improves tool stability and contributes to predictable wear behaviour for the ZDGT200550R-K85 WNN15 insert. Is WNN15 suitable for hardened steels? WNN15 is a coated-carbide grade; material suitability depends on the specific workpiece and cutting data. It is recommended to verify compatibility using the product matrix or to consult Metav Werkzeuge for application-specific advice. Can the insert be indexed to multiple edges? Yes, the indexable design allows multiple edge positions, enabling efficient edge rotation to extend service life before replacement. What maintenance or inspection routines are advised? Regular monitoring of edge wear and chip form is advised; when chip control degrades or surface finish falls below tolerance, reindexing or replacement of the ZDGT200550R-K85 WNN15 insert should be performed. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanation only. There is no affiliation between our company and the named brands. The offered item is original and brand-new from the manufacturer.
ZDGT200560R-K85 WK10 Wendeplatten - Walter Tools
Take advantage of the combination of a reliable uncoated carbide grade, a dedicated K85 chipbreaker and a flexible 15° relief angle to improve machining stability and repeatability in milling operations. Order the insert directly via Metav Werkzeuge or contact the team for application-specific advice. ZDGT200560R-K85 WK10 — milling indexable insert with K85 chipbreaker, 15° relief | Walter Tools The ZDGT200560R-K85 WK10 is an indexable milling insert designed for general milling tasks where consistent chip control and long tool life are required Uncoated carbide grade WK10 for robust performance K85 chipbreaker for controlled chip formation 15° relief angle for versatile milling applications 6 mm corner radius, 20 mm plate size Consistent chip control and reliable machining results The ZDGT200560R-K85 WK10 insert combines an uncoated carbide substrate with a dedicated K85 chipbreaker to ensure predictable chip formation, especially in interrupted cuts and mixed-material batches. The engineered chip geometry reduces re-cutting of chips and helps maintain stable cutting forces, which directly contributes to improved process stability and fewer tool-related stoppages. For production environments seeking repeatable outcomes, this insert supports a steady surface quality with fewer secondary operations. Versatility across common milling tasks with clear technical benefits With a 15° relief angle and a 6 mm corner radius, the indexable insert offers a balance between edge strength and cutting aggressiveness: the relief angle aids entry and exit on a range of workpiece contours, while the corner radius increases resistance to chipping under moderate feed rates. The 20 mm plate dimension and the thickness code provided allow straightforward integration into standard toolholders. These dimensional characteristics make the insert suitable for a wide variety of milling set-ups without sacrificing the durability needed in batch production. Material suitability and operational guidance for planners The cutting grade WK10 is specified as uncoated carbide; compatibility with particular workpiece materials should be verified against the manufacturer’s product matrix. The insert’s design is aimed at offering broad applicability, but for optimised performance—especially with alloys or tougher steels—feed, speed and coolant strategy should be matched to the application. The robust chip control delivered by the K85 breaker reduces thermal spikes and contributes to longer edge life, lowering the frequency of index changes and increasing uptime. Integration into the production process with low handling complexity Installation and handling are straightforward: the insert’s standardised designation and geometry simplify stockkeeping and tool assembly. The stable cutting edge geometry reduces vibration and supports higher depth-of-cut choices where machine rigidity permits, delivering economic advantages through reduced cycle times. For customers requiring further specification data or process recommendations, detailed technical guidance is available from Metav Werkzeuge to assist with parameter selection and toolholder matching. Contact Metav Werkzeuge for tailored advice on the Walter Tools ZDGT200560R-K85 WK10 insert, compatibility checks and application-specific recommendations Technical data SKU: ZDGT200560R-K85-WK10-WALTER Designation: ZDGT200560R-K85 WK10 Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Dimensions & core data Relief angle: 15° Corner radius: 6 mm Plate size: 20 mm Thickness code: 05 Tolerance class: G Features & suitability Carbide grade: uncoated WK10 Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Design: T Material specification: catalogue-dependent FAQ What materials is this insert suitable for? The insert uses the WK10 uncoated carbide grade; material compatibility should be checked against the Walter product matrix for the ZDGT200560R-K85 WK10 insert to determine best performance with specific steels or alloys. How does the K85 chipbreaker influence machining? The K85 chipbreaker promotes controlled chip segmentation and evacuation, which improves thermal stability and reduces the likelihood of re-cutting; the result is more consistent surface finish and longer edge life for this milling insert. Is the 15° relief angle suitable for finishing and roughing? A 15° relief angle offers a versatile compromise: it supports clean finishing passes while providing enough clearance and edge strength for many light-to-moderate roughing operations with the ZDGT200560R-K85 WK10 insert. How should the 6 mm corner radius be applied in production planning? The 6 mm corner radius increases edge robustness and is well suited to operations where moderate feeds are used; it helps prevent chipping at interrupted cuts and should be considered when specifying tolerances and surface finish requirements. Where can users obtain parameter recommendations for this insert? Parameter and application recommendations for the ZDGT200560R-K85 WK10 insert are available from Metav Werkzeuge and the Walter Tools technical documentation to ensure optimal cutting speed, feed and coolant strategy. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
ZDGT200564R-K85 WK10 T Wendeplatten - Walter Tools
Take advantage of Walter Tools' proven WK10 cutting grade combined with the K85 chipbreaker and a 15° free angle to achieve stable chip control and consistent edge life in milling operations; consult Metav Werkzeuge for application matching or order the insert directly through their sales team. ZDGT200564R-K85 WK10 — Fräswendeschneidplatte (milling indexable insert), Walter Tools — 15° free angle, K85 chipbreaker The ZDGT200564R-K85 WK10 is a milling indexable insert engineered for general‑purpose milling where robust edge strength and controlled chip formation are required. Uncoated carbide for versatile machining 15° free angle for reduced cutting forces 6.4 mm corner radius for increased edge stability K85 chipbreaker for predictable chip control Improve cycle times with a dependable uncoated grade The WK10 grade is an uncoated carbide designed to offer a balance between toughness and wear resistance; this makes the insert suitable for a wide range of milling tasks where a stable cutting edge is important. An uncoated grade avoids the sensitivity to thermal shock that can affect coated alternatives, which benefits operations with interrupted cuts or variable feeds. Choosing a hardmetal grade like WK10 supports longer tool life in many applications and reduces the need for frequent index changes, contributing to lower overall machining costs and steadier production output. Consistent surface quality through optimised geometry Geometry directly affects process reliability: the 15° free angle lowers radial cutting forces and improves engagement in shoulder and slot milling, while the 6.4 mm corner radius strengthens the cutting edge against chipping. The K85 chipbreaker is configured to produce short, controllable chips that evacuate reliably, preventing entanglement and improving surface finish. With a nominal plate size of 20 mm, this insert provides a stable contact area, and its tolerance class G supports predictable clamping and repeatable machining results on automated equipment. Material compatibility and selection guidance Material suitability for this insert should be verified against the manufacturer’s product matrix; the grade information indicates broad applicability but exact performance depends on workpiece material, cutting data and machine characteristics. Where data are limited, testing with representative parameters and close consultation with Metav Werkzeuge or Walter Tools technical literature is recommended. Proper selection of spindle speed, feed and depth of cut—combined with the insert’s geometry—will unlock its potential for efficient, reliable machining. For technical consultation or to specify the ZDGT200564R-K85 WK10 for a production process, contact Metav Werkzeuge for application advice and procurement via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: ZDGT200564R-K85-WK10-WALTER Product type: Fräswendeschneidplatte Designation: ZDGT200564R-K85 ISO designation: ZDGT200564R-K85 WK10 Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Core specifications Free angle: 15° Corner radius: 6.4 mm Plate size: 20 mm Plate thickness: 05 Tolerance class: G Design and features Chipbreaker: K85 Grade: WK10 (uncoated hardmetal) Material specification: Katalogabhängig Execution: T FAQ What materials is this insert suitable for? The ZDGT200564R-K85 WK10 is specified as an uncoated hardmetal grade; material suitability should be checked in the Walter Tools product matrix and aligned with the intended application. How does the K85 chipbreaker affect machining? The K85 chipbreaker promotes controlled, short chips and consistent chip evacuation, which helps to maintain surface quality and reduces the risk of chip-related interruptions when using the insert. What is the effect of the 15° free angle and 6.4 mm radius in practice? A 15° free angle reduces radial cutting forces and improves engagement in common milling operations; a 6.4 mm corner radius increases edge robustness and helps to prevent premature chipping under heavier cuts. How should the correct grade be selected for a specific job? Selection should be based on the workpiece material, cutting conditions and the Walter Tools matrix; for precise matching of cutting data to the ZDGT200564R-K85 WK10, consult Metav Werkzeuge technical advisors. Trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original, brand‑new manufacturer goods. Walter Tools is used where appropriate to identify the product brand. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
ZDGT20A508R-K85 WMG40 Wendeplatten - Walter Tools
Benefit from the combination of the coated carbide WMG40 grade and the K85 chipbreaker for reliable chip control and extended edge life; the 15° relief angle and 0.8 mm corner radius support precise finishing and repeatable results. Order the ZDGT20A508R-K85 WMG40 indexable milling insert directly via Metav Werkzeuge or consult the technical team for application-specific guidance. ZDGT20A508R-K85 WMG40 Indexable milling insert — 15° relief, 0.8 mm corner radius | Walter Tools The ZDGT20A508R-K85 WMG40 is an indexable milling insert designed for versatile finishing and light to medium roughing where a coated carbide grade with controlled chip formation is required. Coated carbide grade WMG40 15° relief angle for smooth engagement 0.8 mm corner radius for consistent edge integrity K85 chipbreaker for reliable chip control 20 mm nominal insert size Increased productivity through stable chip control The combination of the WMG40 grade and the K85 chipbreaker is engineered to deliver consistent chip formation and reduced edge degradation, which directly improves cycle times and tool life. As a coated carbide solution, the insert offers a balance between wear resistance and toughness, making it suitable for many general milling tasks. The measurable benefit is fewer interruptions for tool changes and a more predictable machining process, supporting higher throughput in batch and single-piece production alike. Precision benefits from geometry and tolerance A 15° relief angle together with a 0.8 mm corner radius stabilises cutting forces and helps maintain a consistent cutting edge during finishing passes. The specified tolerance class G and the plate thickness A5 ensure dimensional stability in clamping and indexing, which contributes to repeatable part quality. For applications sensitive to surface finish and dimensional accuracy, these geometric characteristics reduce the risk of chatter and minimise rework. Application guidance and material suitability Material suitability for this insert is catalog-dependent; the grade description therefore recommends checking the manufacturer’s product matrix for specific recommendations. The WMG40 grade is described as a coated carbide class in the series information, and the insert is intended for a broad material spectrum when the correct cutting data are applied. For unfamiliar materials or specialised alloys, consult the product matrix to select cutting parameters that preserve tool life and component integrity. For tailored recommendations on using Walter Tools ZDGT20A508R-K85 WMG40 inserts and to obtain the current product matrix, contact Metav Werkzeuge for technical consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical Data Article number: ZDGT20A508R-K85-WMG40-WALTER Product name: ZDGT20A508R-K85 WMG40 Product type: Indexable milling insert Manufacturer: Walter Tools Facts Insert size: 20 mm Relief angle: 15° Corner radius: 0.8 mm Thickness: A5 Tolerance class: G Special features Grade: WMG40 Chipbreaker: K85 Material: Catalog-dependent Coated carbide Series: Walter Schneidstoffsorte - Serie offen FAQ Which materials is this insert suitable for? Material suitability should be verified against the manufacturer product matrix; the ZDGT20A508R-K85 WMG40 is a coated carbide grade and the matrix lists the recommended materials and cutting ranges. What advantage does the K85 chipbreaker provide? The K85 chipbreaker promotes controlled chip formation, improving evacuation and reducing the risk of built-up edge, which supports consistent surface finish and longer tool life with the ZDGT20A508R-K85 WMG40 insert. How does the 15° relief angle influence cutting behaviour? A 15° relief angle reduces the contact area behind the cutting edge, lowering friction and heat generation during engagement; this helps achieve smoother finishes and limits premature edge wear. Can the insert be used for finishing and roughing operations? The geometry, including the 0.8 mm corner radius, makes the insert suitable for finishing and light to medium roughing when matched with appropriate cutting data from the product matrix. What does tolerance class G indicate for this insert? Tolerance class G specifies the dimensional tolerances for the insert to ensure reliable seating and repeatable indexing in toolholders, which is important for maintaining part accuracy in serial production. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no connection between our company and the brands named. The offered item is an original, factory-new article of the manufacturer.
ZDGT20A516R-K85 WMG40 Wendeplatten - Walter Tools
Benefit from the combination of reliable chip control and robust edge life provided by the WMG40 grade and the K85 chipbreaker; the result is steady machining performance and predictable process stability. Order the insert directly via Metav Werkzeuge or consult the advisers for material-specific recommendations. ZDGT20A516R-K85 WMG40 indexable milling insert, K85 chipbreaker (15°) — Walter Tools The ZDGT20A516R-K85 WMG40 is an indexable milling insert engineered for stable milling operations across a range of workpiece materials; designed primarily for industrial metalcutting where reliable chip formation and repeatable edge life are required. Coated carbide grade WMG40 K85 chipbreaker for chip control 15° relief angle for stable cutting 1.6 mm corner radius for robustness Consistent chip control and efficient material removal The combination of the K85 chipbreaker and the WMG40 coating provides controlled chip formation, which reduces interruptions and promotes continuous material removal. The insert's geometry is optimised to produce short, manageable chips under a variety of cutting conditions; this leads to fewer downtimes for chip clearing and contributes directly to higher process efficiency. The clear, engineered chip flow also helps to reduce heat concentration on the cutting edge, supporting longer tool life and more predictable component quality. Reproducible edge life and cutting stability With a 15° relief angle and a 1.6 mm corner radius, the insert is designed to balance sharpness and edge strength. The specified relief minimises rubbing while maintaining sufficient support behind the cutting edge, and the larger corner radius enhances resistance to edge chipping during interrupted cuts. Specified tolerance class G and A5 thickness provide mechanical stability in the toolholder, which translates to consistent dimensional accuracy on the workpiece and fewer rejects during production. Material guidance and process integration The WMG40 grade is a coated carbide formulation intended for versatile performance; however, the exact suitability for specific alloys should be verified against the manufacturer's product matrix. Material data are catalogue-dependent and must be checked prior to application to ensure optimal cutting parameters. For integration into an existing toolchain, documentation of cutting conditions and a short trial run are recommended to confirm feeds and speeds, chip behaviour, and surface finish under the given machine and clamping conditions. Contact Metav Werkzeuge for tailored technical data and procurement of Walter Tools inserts; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: ZDGT20A516R-K85-WMG40-WALTER Label: Fräswendeschneidplatte ZDGT20A516R-K85 WMG40 Walter Tools Manufacturer: Walter Tools SKU/UID: ZDGT20A516R-K85-WMG40-WALTER Facts Plate size: 20 mm Corner radius: 1.6 mm Relief angle: 15° Thickness: A5 Tolerance class: G Special features Grade: WMG40 (coated carbide) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material specification: Katalogabhängig FAQ What materials is this insert suited for? The ZDGT20A516R-K85 WMG40 insert uses the WMG40 coated carbide grade and can machine a broad range of materials; exact compatibility should be checked in the Walter Tools product matrix for the specific workpiece alloy. How does the K85 chipbreaker influence machining performance? The K85 chipbreaker promotes controlled chip formation and evacuation, improving machining continuity and reducing the risk of chip-related interruptions when using the ZDGT20A516R-K85 WMG40 indexable insert. What do the geometry values mean for process reliability? A 15° relief angle reduces rubbing while maintaining support behind the edge, and the 1.6 mm corner radius increases edge robustness; together these features enhance stability and repeatable edge life for the ZDGT20A516R-K85 WMG40. Is the WMG40 grade a coated or uncoated substrate? The WMG40 designation refers to a coated carbide grade as specified by Walter Tools; further substrate details are catalogue-dependent and should be consulted in the product documentation. What tolerance and thickness specifications apply to this insert? This insert is specified with tolerance class G and a plate thickness A5, which support dimensional consistency and mechanical stability in standard toolholders when using the ZDGT20A516R-K85 WMG40. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT20A520R-K85 WMG40 WMG40 Wendeplatten - Walter Tools
Taking advantage of the combination of stable chip control, robust edge life and consistent dimensional tolerance ensures reliable machining and predictable tool performance; order the ZDGT20A520R-K85 WMG40 milling insert directly via Metav Werkzeuge or consult the product specialists for application-specific advice ZDGT20A520R-K85 WMG40 milling insert by Walter Tools — coated carbide grade with K85 chipbreaker The ZDGT20A520R-K85 WMG40 is a coated carbide indexable milling insert intended for general milling tasks where consistent chip formation and durable cutting edges are required Coated carbide grade WMG40 15° relief angle for low cutting forces 2 mm corner radius for durable edges K85 chipbreaker for stable chip control Productive cutting with controlled chip formation The coated carbide grade WMG40 is formulated for reliable performance across common milling applications, combining wear resistance with predictable flank behaviour. The K85 chipbreaker is engineered to promote stable chip control, which reduces the risk of entanglement and supports continuous material evacuation in medium to heavy cutting conditions. Thanks to the 15° relief, cutting forces are moderated, resulting in smoother engagement and reduced spindle load. These attributes translate into measurable process advantages: fewer interruptions, consistent component quality and improved machine utilisation. For materials suitability, the product matrix should be consulted to match the grade to the workpiece material. Durable geometry for repeatable accuracy The insert’s 2 mm corner radius and tolerance class G are core contributors to long-term dimensional stability during series production. A larger nose radius improves corner strength and edge life, particularly when offsetting slightly increased cutting loads, while the defined tolerance class supports interchangeability and consistent placement in clamping systems. The thickness designation A5 indicates the robust plate body that resists deformation under cutting stress. Together, these geometric features help maintain surface finish and positional accuracy across repeated tool changes and re-indexing, making the insert suitable for workflows that prioritise repeatable results. Simple integration into milling operations Designed as an indexable milling plate with a nominal size of 20 mm, this insert fits typical milling setups where standardised insert geometries are used. The series information — Walter Schneidstoffsorte - Serie offen — and the execution code T identify the manufacturing variant and assist in selecting the correct counterpart in tool assemblies. The ISO designation ZDGT20A520R-K85 WMG40 enables clear ordering and inventory control. While the insert is engineered for broad applicability, checking holder compatibility and cutting data against the workpiece and machine capability is recommended to achieve the best balance of material removal rate and tool life. For precise selection and application support of Walter Tools milling inserts, contact Metav Werkzeuge for tailored recommendations and prompt supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: ZDGT20A520R-K85-WMG40-WALTER Label: Fräswendeschneidplatte ZDGT20A520R-K85 WMG40 Walter Tools Manufacturer: Walter Tools Type: milling insert ISO designation: ZDGT20A520R-K85 WMG40 Grade: WMG40 Series: Walter Schneidstoffsorte - Serie offen Facts Relief angle: 15° Corner radius: 2 mm Plate size: 20 mm Thickness: A5 Tolerance class: G Special features Chipbreaker: K85 Coating / material: coated carbide (check catalogue) Execution: T Product note: Check material suitability according to the product matrix UID / SKU: ZDGT20A520R-K85-WMG40-WALTER FAQ What materials is this insert suitable for? The WMG40 grade is a coated carbide designed for broad application; always verify specific workpiece compatibility with the product matrix for the ZDGT20A520R-K85 WMG40 milling insert. How does the K85 chipbreaker affect machining? The K85 chipbreaker supports controlled chip formation and evacuation, improving process stability and reducing interruptions during longer machining cycles. What does the 15° relief angle provide in practice? A 15° relief reduces cutting forces and helps smoother engagement, which can extend edge life and lower machine load under comparable cutting conditions. Is the geometry suitable for series production? Yes—the combination of a 2 mm corner radius and tolerance class G provides robust edge strength and dimensional consistency for repeatable results. How should the insert be specified when ordering? Order by the ISO designation ZDGT20A520R-K85 WMG40 and the SKU ZDGT20A520R-K85-WMG40-WALTER to ensure correct grade and chipbreaker selection. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the named manufacturers. The offered item is original, brand-new goods supplied by the manufacturer. The brand in this listing is Walter Tools.
ZDGT20A530R-K85 WMG40 Wendeplatten - Walter Tools
Benefit from the combination of a modern coated carbide grade, controlled chip formation and robust geometry for reliable milling performance; order genuine inserts directly via Metav Werkzeuge or consult the team for application matching. ZDGT20A530R-K85 WMG40 milling insert — Walter Tools — 15° relief, 3 mm corner radius ZDGT20A530R-K85 WMG40 is a milling indexable insert designed for productive machining where consistent edge life and controlled chips are required Coated carbide grade WMG40 for wear resistance 15° relief angle for stable milling 3 mm corner radius for enhanced edge strength K85 chipbreaker for controlled chip formation Increased process reliability through a modern coated grade The WMG40 grade is specified as a coated carbide cutting material and provides a baseline for wear resistance and repeatable performance. The coated substrate supports longer tool life under varied operating conditions; however, material compatibility should be checked against the manufacturer product matrix before final selection. This insert designation, ZDGT20A530R-K85 WMG40, allows predictable indexable performance and reduced unplanned downtime when integrated into a matched toolholder and cutting data set. Geometry tuned for consistent surface quality and edge life A 15° relief angle and a 3 mm corner radius combine to deliver both cutting stability and edge strength. The relief angle reduces rubbing and heat build-up, while the larger corner radius disperses cutting forces across a broader edge, improving resistance to chipping during interrupted cuts. These geometric choices translate into more consistent surface finish and extended intervals between insert changes when the machining parameters and feed conditions are adapted to the component geometry. Controlled chip formation to support efficient production The K85 chipbreaker is engineered for reliable chip control in typical milling tasks, helping to avoid entanglement and enabling uninterrupted chip evacuation. Better chip management lowers cycle-time variability and reduces the need for secondary cleaning operations. In production contexts where repeatability and process stability are priorities, the chipbreaker design helps maintain tool performance across batches. Practical identification and inventory benefits The base designation ZDGT20A530R-K85 and the clear grade marking WMG40 simplify stock management and reorder planning. The tolerance class G and the specified thickness and shape codes permit easy cross-referencing with toolholder specifications and NC programmes. For precise application guidance and to confirm suitability for specific materials or cutting strategies, Metav Werkzeuge’s technical advisers can provide the validated cutting data required for a safe and productive implementation. Contact Metav Werkzeuge for tailored application advice or to order genuine Walter Tools inserts by emailing info@metav-werkzeuge.com or calling +49 2822 7131930 Technical data Article number: ZDGT20A530R-K85-WMG40-WALTER Designation: ZDGT20A530R-K85 WMG40 Product type: Milling insert Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 3 mm Plate size: 20 mm Thickness: A5 Tolerance class: G Special features Grade: WMG40 (coated carbide) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Execution: T Base designation: ZDGT20A530R-K85 FAQ What materials is this insert suitable for? Material compatibility depends on the chosen cutting data and the product matrix; the ZDGT20A530R-K85 WMG40 insert is a coated carbide grade and suitability should be checked against the manufacturer’s application chart. How does the K85 chipbreaker affect machining? The K85 chipbreaker promotes controlled chip formation, aiding chip evacuation and reducing the risk of entanglement during milling with this milling insert. Can the corner radius be changed for different finishes? Different corner radii offer trade-offs between edge strength and surface finish; the 3 mm corner radius on this insert prioritises edge robustness for interrupted or heavy cuts. How can the insert be identified for reordering? Use the full designation ZDGT20A530R-K85 WMG40 and the SKU ZDGT20A530R-K85-WMG40-WALTER when reordering to ensure the correct Walter Tools grade and geometry are supplied. The Walter AG (brand: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. No affiliation between our company and the named manufacturers is implied. The offered article is original and brand-new. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
ZDGT20A540R-K85 WMG40 WMG40 Wendeplatten - Walter Tools
Combining the WMG40 coated carbide with the K85 chipbreaker and a 15° relief angle results in a milling insert that balances reliable chip control with consistent edge life; order the ZDGT20A540R-K85 via Metav Werkzeuge or consult our specialists for application-specific advice. ZDGT20A540R-K85 WMG40 indexable milling insert — 15° relief, K85 chipbreaker — Walter Tools The ZDGT20A540R-K85 WMG40 is an indexable milling insert intended for general high-productivity milling operations where controlled chip formation and consistent cutting performance are required. 15° relief angle for stable cutting 4 mm corner radius for edge strength K85 chipbreaker for controlled chips WMG40 coated carbide grade High-output milling through engineered chip control The combination of a K85 chipbreaker and a WMG40 coated carbide grade is designed to improve machining stability and reduce interruptions due to poor chip evacuation. The chipbreaker geometry promotes predictable chip segmentation, which lowers the risk of recutting and tool damage during medium to high material removal rates. The 15° relief angle contributes to a reduced cutting force and helps maintain a steady engagement with the workpiece, so production cycles run more reliably and tool changes can be planned rather than improvised. Precision, edge security and surface quality A 4 mm corner radius increases edge robustness and distributes cutting stresses over a larger area, which supports longer edge life and more consistent surface finish in finishing and semi-finishing passes. The insert’s tolerance class G ensures repeatable positioning within the toolholder pocket, helping to maintain dimensional accuracy across a batch. The plate thickness code A5 and the standardised ISO designation facilitate correct seating and replacement, reducing set-up time and avoiding costly mismatches during changeovers. Practical use and material considerations for reliable machining This insert is delivered in the ZDGT20A540R-K85 format and belongs to the Walter Schneidstoffsorte — Serie offen. Material designation is catalogue-dependent, so suitability for specific substrates should be verified against the manufacturer matrix before cutting. The insert’s geometry and coated-carbide grade make it well suited to general milling tasks where consistent chip control and long tool life are priorities. For tailored recommendations on feeds, speeds and toolholder selection, request the technical data sheet or task-specific guidance. For application-specific selection or to order Walter Tools inserts such as the ZDGT20A540R-K85 WMG40, contact Metav Werkzeuge for expert advice and prompt supply: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: ZDGT20A540R-K85-WMG40-WALTER Label: Fräswendeschneidplatte ZDGT20A540R-K85 WMG40 Walter Tools Manufacturer: Walter Tools ISO designation: ZDGT20A540R-K85 WMG40 Designation without grade: ZDGT20A540R-K85 Facts Relief angle: 15° Corner radius: 4 mm Plate size: 20 mm Thickness: A5 Tolerance class: G Special features Chipbreaker: K85 Grade: WMG40 (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: Catalogue-dependent FAQ What machining tasks is this insert suitable for? The ZDGT20A540R-K85 WMG40 insert is intended for general milling operations where controlled chip formation and steady cutting performance are required. What benefit does the K85 chipbreaker provide? The K85 chipbreaker on the ZDGT20A540R-K85 promotes predictable chip segmentation and improved chip evacuation, reducing recutting and the risk of tool damage. How does the 4 mm corner radius affect performance? A 4 mm corner radius increases edge strength and distributes cutting loads, which improves tool life and supports a consistent surface finish during finishing and semi-finishing passes. What does the WMG40 grade mean in practice? WMG40 denotes a coated carbide grade used by Walter Tools that aims to provide a balance between wear resistance and toughness; compatibility with specific materials should be checked against the product matrix. How is the insert identified for reordering? Reorder using the ISO designation ZDGT20A540R-K85 WMG40 or the article number ZDGT20A540R-K85-WMG40-WALTER to ensure the correct grade and chipbreaker are supplied. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
ZDGT20A550R-K85 WMG40 Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide performance and a K85 chipbreaker for reliable chip control; with a 15° relief angle and a robust 5 mm corner radius, the insert supports stable machining and long tool life. Order the insert directly via Metav Werkzeuge or consult our advisors for application-specific guidance. ZDGT20A550R-K85 WMG40 milling indexable insert — Walter Tools, 15° relief & K85 chipbreaker The ZDGT20A550R-K85 WMG40 is a precision milling indexable insert designed for general milling applications; it combines a coated-carbide grade with a K85 chipbreaker for predictable chip formation and consistent edge stability. Coated carbide grade WMG40 15° relief angle for stable cutting 5 mm corner radius for robust edge K85 chipbreaker for reliable chip control Increased process reliability for stable machining The combination of a WMG40 coated-carbide grade and a defined 15° relief angle reduces cutting forces and contributes to consistent engagement during milling. This technical pairing promotes stable chip formation, which in turn minimises tool vibration and helps maintain dimensional accuracy across batches. For production environments where repeatability matters, the insert’s geometry supports steady metal removal and reduces the need for frequent rework. Robust edge life and wear resistance A 5 mm corner radius and the coated-carbide construction provide a durable cutting edge capable of withstanding intermittent heavy cuts. The coating and substrate combination improves resistance to adhesive and abrasive wear, extending effective tool life under varied conditions. As a result, machining cycles can run longer between indexings, helping to maintain throughput without sacrificing surface quality. Predictable chip control and machining outcomes The integrated K85 chipbreaker is engineered to control chips in a wide range of cutting conditions, improving evacuation and reducing the risk of recutting. Better chip management leads to improved surface finish and easier handling at the machine. Because the material specification is catalogue-dependent, verification against the product matrix is recommended to confirm suitability for specific alloys or machining strategies. Practical guidance for application and selection This insert is supplied in the ZDGT20A550R-K85 designation and should be matched to appropriate cutter bodies and clamping systems. The plate thickness and form (A5) and the tolerance class G ensure compatibility with standard milling holders; consult the product matrix where necessary. For unfamiliar materials or critical surface requirements, trial cuts and parameter optimisation will secure the best combination of feed, speed and coolant strategy. Contact Metav Werkzeuge today for technical pairing advice, cutter compatibility checks or to request the detailed product matrix for the ZDGT20A550R-K85 WMG40 milling insert — Metav Werkzeuge is ready to assist with application-specific recommendations. Technical Data Article number: ZDGT20A550R-K85-WMG40-WALTER Designation: ZDGT20A550R-K85 Grade: WMG40 Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 5 mm Plate size: 20 Thickness: A5 Tolerance class: G Special features Coated carbide (catalogue-dependent) Chipbreaker: K85 Series: Walter Schneidstoffsorte - Serie offen Execution: T Sortenbeschreibung: coated carbide grade; verify material suitability in product matrix FAQ What materials is this insert suitable for? The ZDGT20A550R-K85 WMG40 insert is a coated-carbide grade; suitability depends on the product matrix and should be checked against the specific workpiece material before application. How does the K85 chipbreaker improve performance? The K85 chipbreaker promotes consistent chip formation and evacuation, leading to improved surface finish and fewer interruptions during machining with this Walter Tools milling insert. What does the 5 mm corner radius mean for cutting behaviour? A 5 mm corner radius provides a more robust cutting edge, reducing the risk of chipping under interrupted cuts and contributing to longer edge life for the ZDGT20A550R-K85 insert. Is the coating specified in the data? The coating is described as catalogue-dependent for this insert; consult Metav Werkzeuge or the product matrix for the exact coating specification for the WMG40 grade. Which cutter bodies are compatible with this designation? The ZDGT20A550R-K85 designation corresponds to standard indexable milling holders; match the insert to the cutter body and clamping system recommended by Walter Tools for secure fit and optimal performance. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only and do not imply any affiliation between our company and the trademark owners. The item offered is original, brand-new merchandise from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com