CCMT09T304-FW4 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance, the WSM10S grade designed for tough alloys, and precise geometry for reliable turning of rostfreier Stahl; order the CCMT09T304-FW4 WSM10S insert via Metav Werkzeuge or ask the consultants for application-specific advice. CCMT09T304-FW4 WSM10S indexable turning insert by Walter Tools — Tiger·tec Silver grade for rostfreier Stahl and superalloys The CCMT09T304-FW4 WSM10S is an indexable turning insert engineered for heavy-duty and heat-sensitive materials, combining a thermally resistant coating with a robust chipbreaker for stable metalcutting. Tiger·tec Silver coating for high thermal resistance WSM10S grade for rostfreier Stahl and superalloys FW4 chipbreaker for controlled chip formation Rhombus 80° geometry with 0.4 mm corner radius Consistent cutting performance where heat and toughness challenge the process The combination of Tiger·tec Silver coating and WSM10S grade provides improved thermal stability and edge life in applications with elevated cutting temperatures. This insert is optimised for machining rostfreier Stahl and heat-resistant superalloys, where conventional grades struggle with built-up edge and rapid wear. The coated carbide substrate supports a secure cutting edge, while the FW4 chipbreaker promotes consistent chip control; together these features reduce edge failure and contribute to predictable tool life, supporting throughput and reducing unscheduled tool changes. Geometry that secures dimensional accuracy and surface quality Precision geometry matters for turning operations that demand repeatability. The Rhombus 80° form and 0.4 mm corner radius balance strength and fine finishing capability, while the 7° clearance minimises rubbing on the flank face. The insert’s size designation and plate thickness support stable clamping and stiffness in the toolholder, helping to maintain tolerances and deliver repeatable surface finishes. For workshops seeking a reliable mix of robustness and finish, this geometry helps to lower scrap rates and stabilise cycle times. Process efficiency and predictable tool management in production Designed for demanding materials and continuous production, this insert contributes to higher process security and cost-efficient machining. The engineered chip control reduces interruptions from troublesome chips, while the grade’s resistance to thermal loading prolongs edge life, which in turn reduces downtime for index changes. When paired with appropriate cutting data and a suitable toolholder, the insert supports a productive turning strategy that emphasises stability and consistent output—key for manufacturers aiming to optimise both throughput and component quality. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Silver inserts and expert guidance to match the CCMT09T304-FW4 WSM10S to specific rostfreier Stahl or superalloy turning tasks Technical data Article number: CCMT09T304-FW4-WSM10S-WALTER Designation: CCMT09T304-FW4 WSM10S Product type: indexable turning insert Series: Tiger·tec Silver Grade: WSM10S Manufacturer: Walter Tools Facts Clearance: 7° Corner radius: 0.4 mm Plate size: 09 Plate thickness: T3 Plate form: Rhombus 80° Tolerance class: M Special features Coating: Tiger·tec Silver Substrate: coated carbide Chipbreaker: FW4 Material groups: S / M Typical applications: rostfreier Stahl; heat-resistant superalloys and titanium FAQ What materials is this insert suitable for? The CCMT09T304-FW4 WSM10S is specified for machining rostfreier Stahl and heat-resistant superalloys (material groups M and S), reflecting the WSM10S grade’s thermal and edge stability. How does the FW4 chipbreaker influence performance? The FW4 chipbreaker on the CCMT09T304-FW4 WSM10S promotes controlled chip formation and evacuation, reducing interruptions and supporting a stable cutting process with improved surface results. Is this insert compatible with standard CCMT toolholders? The CCMT09T304-FW4 WSM10S follows the CCMT indexable insert geometry and fits standard CCMT-compatible turning toolholders; correct clamping and seat condition remain essential for optimal performance. What advantages does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases thermal resistance and wear protection, which is especially beneficial when turning tough, heat-prone materials such as rostfreier Stahl and nickel-based alloys. Can the CCMT09T304-FW4 WSM10S be used for finishing operations? With its 0.4 mm corner radius and Rhombus 80° geometry, the insert can achieve acceptable surface quality in many finishing passes; cutting parameters should be adapted to the component’s tolerance and surface requirements. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany; info@walter-tools.com Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
CCMT09T304-FW4 WSM20S FW4 Wendeplatten - Walter Tools
For reliable machining of stainless steels and heat‑resistant alloys, this turning insert combines a Tiger·tec Silver coated grade with the FW4 chipbreaker and a 0.4 mm corner radius for secure chip control and extended edge life; Order the CCMT09T304‑FW4 WSM20S turning insert directly via Metav Werkzeuge or ask our consultants if needed. CCMT09T304‑FW4 WSM20S turning insert — Tiger·tec Silver, 7° clearance (Walter Tools) The CCMT09T304‑FW4 WSM20S is a rhombic 80° indexable turning insert engineered for demanding turning in stainless steels and superalloys, offering a robust chipcontrol geometry and a coated carbide grade for improved thermal resistance. Tiger·tec Silver coating for heat resistance FW4 chipbreaker for secure chip control 7° clearance angle for consistent cutting Rhombic 80° shape with 0.4 mm corner radius High‑temperature performance for stainless steels and superalloys The coated carbide grade WSM20S, part of the Tiger·tec Silver series, is designed for the tribological and thermal challenges of groups M and S (stainless steels and heat‑resistant superalloys). The advanced coating reduces adhesion and supports a stable cutting edge, which helps to avoid built‑up edge and premature flank wear in tough materials. The chipbreaker geometry improves evacuation and reduces the risk of long, stringy chips, translating into fewer interruptions and higher process reliability — an important consideration for batch production and safety‑critical components. Precision geometry that improves surface quality and tool life The rhombic 80° shape combined with a 0.4 mm corner radius provides a balance between edge strength and finishing capability: the modest radius gives a robust cutting corner for interrupted cuts while still enabling a fine surface finish on profile turning. A 7° clearance angle helps to maintain a predictable contact geometry and reduces rubbing in heavy cuts, which benefits tool life and reduces heat generation. The FW4 chipbreaker is tuned to support consistent chip segmentation in loaded cutting conditions, making the insert a pragmatic choice where both reproducibility and part quality matter. Productivity benefits and shopfloor integration As a production‑oriented grade from Walter Tools, this insert supports repeatable performance and fewer tool changes under demanding conditions, which improves uptime and machining efficiency. Using a coated, application‑focused grade means higher cutting speeds and longer intervals between indexings compared with uncoated carbide in similar tasks. For users aiming to streamline tool inventories, the CCMT geometry and common dimensions simplify stocking and allow rapid replacement in standard toolholders. Selection of cutting data should follow manufacturer guidance and be adapted to the specific alloy and rigidity of the machine setup to unlock the full productivity potential. For bespoke application recommendations and to secure supply of Walter Tools Tiger·tec Silver inserts, contact Metav Werkzeuge for technical consultation and ordering support. Technical data SKU: CCMT09T304-FW4-WSM20S-WALTER Designation: CCMT09T304-FW4 WSM20S Product type: Turning insert Series: Tiger·tec Silver Grade: WSM20S Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Tolerance class: M Features / Applications Chipbreaker: FW4 Shape: Rhombic 80° Execution: T Suitable for: stainless steels (M) and superalloys (S) Applicable material groups: S / M FAQ Which materials is this insert intended for? The CCMT09T304‑FW4 WSM20S is specified for stainless steels (ISO group M) and heat‑resistant superalloys (ISO group S), the grade and chipbreaker support secure chip formation in these materials. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker on this insert promotes controlled chip segmentation and evacuation, reducing chip‑related interruptions when machining high‑temperature alloys with the CCMT09T304‑FW4 WSM20S. What advantage does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases thermal resistance and reduces adhesion, which helps maintain a stable cutting edge and extends tool life under elevated cutting temperatures. Is the 0.4 mm corner radius suitable for finishing? A 0.4 mm corner radius offers a compromise between a strong cutting edge and surface finish; it is suitable for many finishing and medium‑duty turning tasks using the CCMT09T304‑FW4 WSM20S. Can this insert be used in standard CCMT toolholders? Yes, the CCMT designation matches standard indexable turning toolholders, enabling straightforward integration into existing setups for the CCMT09T304‑FW4 WSM20S. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned solely for explanatory purposes and do not indicate any affiliation with our company. The offered article is an original, factory‑new product of Walter Tools.
CCMT09T304-FW4 WSM30S FW4 Wendeplatten - Walter Tools
The combination of Tiger·tec Silver coating and the WSM30S grade delivers high edge stability and extended tool life for demanding turning operations; the result is reliable performance when machining stainless steels and heat‑resistant superalloys. Order the insert directly via Metav Werkzeuge or consult the specialists for application‑specific cutting data. CCMT09T304-FW4 WSM30S rhombic 80° turning insert, Tiger·tec Silver — Walter Tools The CCMT09T304-FW4 WSM30S is a rhombic 80° indexable insert with a FW4 chipbreaker, designed for heavy duty machining of stainless steels and difficult‑to‑cut superalloys in industrial turning applications. Tiger·tec Silver coating for wear resistance Optimised for stainless steel and superalloys Rhombic 80° geometry with 0.4 mm radius FW4 chipbreaker for consistent chip control Improved process reliability for tough materials The combination of the WSM30S grade and Tiger·tec Silver coating is engineered to resist the thermal and mechanical loads typical of machining stainless steels and superalloys. This results in stable cutting edges and reduced flank wear over successive passes, which directly improves component consistency and reduces unexpected tool changes. For production environments where downtime and scrap cost are critical, the insert’s composition supports a predictable tool life and repeatable results. Consistent chip control for cleaner finishes The FW4 chipbreaker geometry promotes controlled chip formation even under adverse cutting conditions, which helps prevent chip entanglement and improves surface integrity. Controlled chips also reduce secondary operations and aid automatic chip evacuation in CNC lathes. The outcome is a better surface finish and fewer interruptions in the machining cycle, supporting higher throughput and reduced rework. Geometry that balances strength and precision With a rhombic 80° form and a 0.4 mm corner radius, this insert provides a robust cutting edge while still enabling precise profile work and reliable corner performance. The 7° clearance angle supports effective cutting without excessive rubbing, and the insert thickness (T3) contributes to rigidity in the toolholder. Together, these design choices ensure an appropriate compromise between component accuracy and the mechanical demands of heavier cuts. Practical benefits for workshop integration The insert’s ISO designation CCMT09T304‑FW4 simplifies selection for tooling systems and reduces set‑up time when matching inserts to holders. Its suitability for ISO material groups M (stainless steels) and S (heat‑resistant superalloys and titanium) means fewer grade changes across mixed batches, improving inventory efficiency. As part of Walter Tools’ Tiger·tec Silver family, the cutting grade is intended to deliver reproducible performance and easier process standardisation across series of parts. Contact Metav Werkzeuge for tailored cutting data and application guidance on Walter Tools Tiger·tec Silver inserts; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for expert recommendations Technical Data Article number: CCMT09T304-FW4-WSM30S-WALTER Product type: Turning insert (indexable insert) Designation: CCMT09T304-FW4 WSM30S Manufacturer: Walter Tools Core technical data Geometry: Rhombic 80° Corner radius: 0.4 mm Clearance angle: 7° Insert size: 09 Thickness: T3 Chipbreaker: FW4 Grade: WSM30S Special features Coating technology: Tiger·tec Silver Material suitability: stainless steels (ISO group M) Also suitable for: heat‑resistant superalloys / titanium (ISO group S) Tolerance class: M Series: Tiger‑tec Silver FAQ Which materials is this insert suited for? The CCMT09T304‑FW4 WSM30S insert from Walter Tools is specifically formulated for stainless steels (ISO group M) and is also suitable for difficult‑to‑cut superalloys and titanium (ISO group S). What benefit does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on the WSM30S grade increases heat and wear resistance, leading to improved edge stability and longer service life in demanding turning operations. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker promotes controlled chip formation and evacuation, which enhances surface finish quality and reduces the risk of chip‑related interruptions during automated turning. Is the 0.4 mm corner radius suitable for finishing operations? A 0.4 mm corner radius balances edge strength with the ability to achieve fine surface finishes; it is suitable for semi‑finish and many finishing passes depending on component geometry. Can this insert be used across mixed production batches? Yes — the WSM30S grade’s suitability for ISO groups M and S supports a wider range of materials, helping to streamline tooling choices across varied production requirements. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
CCMT09T304-MK4 WKK10S WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance, a dedicated MK4 chipbreaker and the rhombic 80° geometry for reliable cast iron turning; order directly via Metav Werkzeuge or consult our specialists for process optimisation. CCMT09T304-MK4 WKK10S — Walter Tools turning insert, Tiger·tec Silver for cast iron The CCMT09T304-MK4 WKK10S is a rhombic 80° indexable turning insert designed for efficient machining of cast iron, combining a coated carbide grade with a specialised chip control geometry Tiger·tec Silver coating for extended tool life Optimised for cast iron machining (K) Rhombic 80° insert with 0.4 mm corner radius 7° clearance angle for stable cutting performance Consistent chip control increases productive cutting time The combination of the Tiger·tec Silver coating and the WKK10S grade targets the specific challenges of cast iron, where abrasive wear and short, breaking chips are common. The MK4 chipbreaker is engineered to promote controlled chip formation, reducing frequent interruptions for chip clearing and lowering the risk of built-up edge. As a result, machining cycles achieve higher effective cutting time and a more predictable tool life, which supports stable production planning and fewer unscheduled tool changes. Geometry and edge design for repeatable surface quality The rhombic 80° insert geometry with a 0.4 mm corner radius and 7° clearance angle provides a balance between edge strength and accessibility for finishing passes. With a T3 plate thickness and tolerance class M, this design gives robust edge support under intermittent cutting typical in cast iron operations and improves repeatability across multiple indexings. The geometry supports consistent component finishes while maintaining a compromise between cutting forces and dimensional control in serial and small-batch runs. Process reliability and easy integration into turning cells As an indexable insert in the CCMT format, the component integrates into widely used toolholders for turning applications without the need for special fixtures. The coated carbide construction offers resistance to abrasive wear, contributing to predictable performance in abrasive cast iron grades. The product’s attributes promote process stability and support higher throughput with fewer tool interventions, making it suitable for workshops aiming to improve productivity while maintaining workpiece quality under varying production demands. Contact Metav Werkzeuge for application guidance and to secure Walter Tools CCMT09T304-MK4 WKK10S inserts for dependable cast iron turning Technical Data Article number: CCMT09T304-MK4-WKK10S-WALTER Designation: CCMT09T304-MK4 WKK10S Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Series: Tiger-tec Silver Grade: WKK10S Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 09 Plate thickness: T3 Geometry: Rhombic 80° Tolerance class: M Special features Coated carbide (Tiger·tec Silver) Chipbreaker: MK4 Optimised for cast iron (K) Suitable for indexable CCMT turning applications Stable cutting performance and abrasive wear resistance FAQ Is this insert suitable for different cast iron grades? The CCMT09T304-MK4 WKK10S grade is tailored for a broad range of cast iron materials and addresses abrasive wear and chip control specific to these grades. What benefit does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating enhances wear resistance and thermal stability, extending tool life and supporting more consistent cutting performance when machining cast iron. Can the insert be used for finishing as well as roughing? With its rhombic 80° geometry and a 0.4 mm corner radius, the insert is adaptable to both semi-finishing and finishing tasks, provided cutting data are adjusted according to the operation. How does the MK4 chipbreaker improve productivity? The MK4 chipbreaker promotes predictable chip formation in cast iron, minimising chip-related interruptions and enabling longer productive cutting intervals. Which toolholders are compatible with this insert format? The CCMT designation indicates compatibility with standard CCMT indexable turning toolholders; toolholder selection should match insert clamping and clearance requirements. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only; no connection exists between our company and the named brands. The offered item is original, brand-new goods of the manufacturer.
CCMT09T304-MM4 WMP20G MM4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, proven chip control and precise geometry for efficient turning of stainless steel; this yields reliable edge life and stable production. Order the CCMT09T304‑MM4 WMP20G directly via Metav Werkzeuge or consult the team for application advice. CCMT09T304‑MM4 WMP20G turning insert — Rhombic 80°, Tiger‑tec Gold (Walter Tools) A CCMT09T304‑MM4 WMP20G indexable turning insert engineered for machining stainless steel under medium to robust cutting conditions. Tiger‑tec Gold coating for extended tool life Optimised chip control with MM4 breaker Rhombic 80° shape, 0.4 mm corner radius 7° relief angle for secure cutting Proven coating and grade for longer production runs The Tiger‑tec Gold coating combined with the WMP20G grade provides a balanced performance for demanding turning tasks on stainless steel. The multilayer coating reduces adhesive wear and supports a stable cutting edge under elevated temperatures, which in turn extends component life and reduces tool-change frequency. This results in measurable cost benefits through longer intervals between regrinds and fewer scrap parts. The coated carbide composition is designed to maintain cutting-edge integrity during medium to robust operations, enhancing process reliability in series production. Geometry that stabilises chip formation and surface quality The insert’s MM4 chipbreaker and rhombic 80° geometry are configured to promote predictable chip control and a consistent surface finish. A 0.4 mm corner radius helps to balance strength and finish quality, while the 7° relief angle supports secure cutting engagement in stainless material, minimising built‑up edge. Together, these features reduce vibrations and improve dimensional repeatability. For workshops seeking improved cycle times without sacrificing quality, the engineered geometry offers a pragmatic route to higher throughput and fewer rework steps. Application scope and workshop integration This indexable insert is sized as a plate 09 with a T3 thickness, suitable for standard turning toolholders that accept CCMT‑style inserts. It is specifically intended for stainless steel machining under medium to heavy conditions where thermal stability and controlled chip evacuation are critical. The design supports straightforward indexation and predictable wear patterns, simplifying tool management and inventory planning. For precise selection of cutting data and holder compatibility, refer to machine specifications and holder manufacturer guidance to ensure optimal clamping and coolant strategies. For tailored advice on integrating the Walter Tools CCMT09T304‑MM4 WMP20G into production and to discuss cutting parameters for specific stainless steel grades, contact Metav Werkzeuge for expert consultation and order support. Technical data SKU: CCMT09T304-MM4-WMP20G-WALTER Designation: CCMT09T304‑MM4 WMP20G Series: Tiger‑tec Gold Grade: WMP20G Facts Relief angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Special features Coating: Tiger‑tec Gold Chipbreaker: MM4 Material group suitability: stainless steel Application: turning / indexable insert FAQ What materials is this insert suitable for? The CCMT09T304‑MM4 WMP20G from Walter Tools is optimised for machining stainless steel, designed to cope with the toughness and heat‑generation typical of these alloys. How does the MM4 chipbreaker affect performance? The MM4 chipbreaker promotes controlled chip formation and evacuation on the CCMT09T304‑MM4 WMP20G, contributing to improved surface finish and reduced risk of built‑up edge when turning stainless steels. What does the 0.4 mm corner radius deliver in practice? A 0.4 mm corner radius on this insert balances edge strength and finish quality, enabling reliable cuts with good surface integrity while offering resistance to mechanical and thermal loading. Is special tooling required to use this insert? The insert is a CCMT‑format indexable plate intended for compatible holders; ensure the chosen toolholder accepts CCMT09 plates and provides secure clamping for stable cutting conditions. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T304-MM4 WMP20S WMP20S Wendeplatten - Walter Tools
High wear resistance and reliable chip control make this coated carbide grade a solid choice for medium to robust turning in rostfreier Stahl; the 0.4 mm corner radius and MM4 chipbreaker improve surface finish and process stability. Order directly via Metav Werkzeuge or consult the specialists for application-specific recommendations. CCMT09T304‑MM4 WMP20S – Rhombic 80° indexable insert for rostfreier Stahl by Walter Tools, 7° clearance, 0.4 mm corner radius CCMT09T304‑MM4 WMP20S is a coated carbide turning insert intended for medium to robust machining of rostfreier Stahl, offering a balance of edge stability and surface quality in production environments Tiger·tec Silver coating for extended tool life Optimised MM4 chipbreaker for secure chip control Rhombic 80° form with 0.4 mm corner radius 7° clearance angle for medium to robust turning Consistent cutting performance for rostfreier Stahl The Tiger·tec Silver WMP20S grade combines a modern coating system with a robust carbide substrate to deliver reliable chip formation and reduced tendency to build up on the cutting edge when machining rostfreier Stahl. The coated surface reduces friction and supports thermal stability at the cutting zone, which in turn helps to maintain a sharper edge for longer. For production planners this translates into more predictable tool life and fewer unscheduled indexings, improving overall process efficiency. Enhanced process reliability and higher output per insert The insert geometry—a rhombic 80° form with a 0.4 mm corner radius and a 7° clearance angle—has been selected to balance strength and surface finish. The MM4 chipbreaker promotes controlled chip segmentation for medium to heavier feeds, reducing the risk of entangling swarf and enabling stable, continuous turning cycles. The practical result is improved productivity through longer tool cycles and fewer interruptions for regrinding or replacement. Clear identification and simple integration into tooling systems The designation indicates form, size, thickness, corner radius and chipbreaker, so the CCMT09T304‑MM4 marking helps to match inserts quickly to compatible tool holders and fixtures. The T3 thickness and size 09 format suit a wide range of commercial turning holders; the modest corner radius supports both finishing and light roughing passes depending on feed. For best results with rostfreier Stahl, use coolant where appropriate and verify insert seating and clamping torque to preserve repeatable performance and cutting-edge stability. Proven Walter Tools technology for dependable production Walter Tools designs its grades and geometries for consistent real‑world performance. The Tiger·tec Silver series focuses on wear resistance and stable edge behaviour in demanding materials such as rostfreier Stahl. Choosing a Walter grade means selecting an insert backed by engineering aimed at process reliability and reproducible results across batches, which supports predictable planning in series production and jobshop environments. For machining rostfreier Stahl with consistent results, contact Metav Werkzeuge to discuss the CCMT09T304‑MM4 WMP20S by Walter Tools and receive tailored advice for the intended application. Technical Data Article number: CCMT09T304-MM4-WMP20S-WALTER SKU: CCMT09T304-MM4 WMP20S Manufacturer: Walter Tools Product type: Indexable turning insert / Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Facts Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 80° Plate size: 09 Thickness: T3 Tolerance class: M Special features Series: Tiger·tec Silver Grade: WMP20S (coated carbide) Chipbreaker: MM4 Suitable for: rostfreier Stahl FAQ What does the designation CCMT09T304‑MM4 indicate? The marking CCMT09T304‑MM4 denotes form, size, thickness, corner radius and the MM4 chipbreaker so the insert can be matched to appropriate tool holders and applications. Is the WMP20S grade suitable for high heat applications in rostfreier Stahl? WMP20S, part of the Tiger·tec Silver series, is engineered for improved thermal stability and wear resistance during machining of rostfreier Stahl under medium to robust conditions. Which operations benefit most from the MM4 chipbreaker? The MM4 chipbreaker supports controlled chip formation in medium to heavier feeds, making it advantageous for stable roughing and semi‑finishing passes where chip control and process continuity matter. How does the 0.4 mm corner radius affect surface finish and strength? A 0.4 mm radius provides a compromise between edge strength and surface quality: it delivers better finish than larger radii while maintaining sufficient edge robustness for typical turning loads. Can this insert be used in standard CCMT holders? Yes; the CCMT09T304‑MM4 format is compatible with standard holders that accept CCMT‑style rhombic 80° inserts, provided correct seating and clamping are observed. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no association between our company and the named brands. The item offered is original, factory‑new goods from the manufacturer.
CCMT09T304-MM4 WMP30G WMP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold wear resistance, optimised MM4 chip control and a precise 0.4 mm corner radius for reliable stainless steel turning; order the inserts directly via Metav Werkzeuge or consult our team for application advice. CCMT09T304‑MM4 WMP30G – Indexable turning insert, rhombic 80°, for stainless steel machining by Walter Tools The CCMT09T304‑MM4 WMP30G is an indexable turning insert designed for robust and consistent performance when machining stainless steel, combining a specialised chipbreaker with a Tiger‑tec Gold coated, coated‑carbide grade for improved process stability. Tiger‑tec Gold coated for extended tool life Optimised MM4 chipbreaker for stable chips Rhombic 80° form with 0.4 mm corner radius Specifically for stainless steel machining Consistent cutting performance for stainless steel components The Tiger‑tec Gold coating and the WMP30G grade deliver stable chip formation and reduced tendency to build up on the cutting edge when machining tough alloys. This combination supports predictable wear behaviour and longer edge life, which translates directly into fewer tool changes and less unplanned downtime. The coated‑carbide substrate is engineered to withstand the heat and adhesion tendencies typical of austenitic and other stainless steels, ensuring that the machining process remains efficient even under medium to more demanding cutting conditions. Geometry that improves surface finish and process reliability A rhombic 80° insert form with a 0.4 mm corner radius and a 7° clearance angle provides a balanced geometry for both finishing and light roughing passes. The compact corner radius reduces cutting forces and helps to maintain a sharp, stable edge, producing consistent surface quality and repeatable dimensional results. These geometric choices are particularly effective in turning operations where control of cutting load and thermal influences is critical for maintaining tolerances on stainless steel parts. Chip control and productivity gains with the MM4 breaker The MM4 chipbreaker is optimised for the material behaviour of stainless steel, promoting short, controllable chips and preventing long stringing that can interrupt automated cycles. Improved chip control reduces the need for operator intervention and enhances throughput; combined with the Tiger‑tec Gold wear characteristics, the insert supports sustained productivity and lower unit costs over long production runs. The result is a pragmatic blend of tool life and process security that benefits batch production and single‑piece flows alike. For reliable stainless steel turning choose Walter Tools Tiger‑tec Gold inserts through Metav Werkzeuge — contact Metav Werkzeuge for tailored recommendations and fast delivery (email info@metav-werkzeuge.com, phone +49 2822 7131930) Technical Data SKU: CCMT09T304‑MM4‑WMP30G‑WALTER Designation: CCMT09T304‑MM4 WMP30G Grade: WMP30G Series: Tiger‑tec Gold Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Special features Coating: Tiger‑tec Gold Chipbreaker: MM4 Shape: Rhombus 80° Material group: M (stainless steel application) Manufacturer: Walter Tools FAQ What materials is this insert optimised for? This insert is optimised for machining stainless steel; the WMP30G grade and Tiger‑tec Gold coating specifically address the adhesion and heat issues common with those alloys. Which chipbreaker is fitted and what benefit does it provide? The MM4 chipbreaker integrated in this insert promotes short, controllable chips and improves process stability when turning stainless steel workpieces. How does the insert geometry affect surface quality? The rhombic 80° form with a 0.4 mm corner radius and 7° clearance reduces cutting forces and helps maintain a sharp edge, resulting in consistent surface finish and dimensional repeatability. Is this insert suitable for both finishing and light roughing? Yes; the combination of corner radius, clearance angle and chip control makes the insert suitable for finishing and light roughing operations on stainless steel components. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T304-MM4 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance and reliable chip control for consistent production; order the insert directly via Metav Werkzeuge or consult our advisors for process-specific recommendations. CCMT09T304-MM4 WSM01 turning indexable insert — 0.4 mm radius, rhombic 80°, Walter Tools A CCMT09T304-MM4 WSM01 insert designed for robust turning and boring work in stainless steels and heat-resistant superalloys, offering a balance of cutting-edge stability and chip control for demanding machining tasks. Tiger-tec Silver coating for enhanced wear resistance Suitable for stainless steels and superalloys M / S Rhombic 80° geometry, 0.4 mm corner radius MM4 chipbreaker for reliable chip control Optimised durability and edge stability for tough materials The Tiger-tec Silver series in combination with the WSM01 grade provides a coated carbide solution optimised for materials that challenge conventional grades. The chemistry and coating promote wear resistance and protect the cutting edge against thermal loading when machining stainless steels and superalloys (material groups M and S). The rhombic outline and small radius support a robust cutting edge, while the MM4 chipbreaker fosters repeatable chip formation; together these characteristics reduce unscheduled tool changes and support steady cycle times in production environments. For further process data or to confirm suitability for a specific alloy, contact Metav Werkzeuge via info@metav-werkzeuge.com or +49 2822 7131930. Process reliability and efficient chip management A focus on process reliability means fewer interruptions and more predictable component quality. The combination of geometry and chip control reduces the risk of built-up edge and erratic chips when turning materials that generate long, stringy swarf. The MM4 chipbreaker is designed to direct chips away from the cutting zone, improving surface finish and protecting the insert flank. With its 7° clearance and robust 0.4 mm corner radius, the insert handles moderate to demanding feeds while still enabling fine finishing passes; this balance supports economical tool life and consistent part tolerances across series production. Practical dimensions and selection guidance for tooling Key dimensions support straightforward selection for tool-holders and toolblocks: insert size 09, T3 thickness, rhombic 80° form and standard 7° clearance. The 0.4 mm corner radius is a compromise between cutting-edge strength and surface integrity — suitable for general-purpose turning where some strength at the nose is required without sacrificing finish. The CCMT designation aligns with common clamping systems, simplifying inventory management and holder compatibility checks. For application-specific recommendations and cutting-parameter ranges tailored to workpiece grade and machine capability, Metav Werkzeuge provides technical consultation to ensure optimal utilisation of the Walter Tools Tiger-tec Silver inserts. Contact Metav Werkzeuge today for tailored advice on Walter Tools Tiger-tec Silver WSM01 inserts and ensure optimal machining of stainless steels and superalloys Technical data Article number: CCMT09T304-MM4-WSM01-WALTER Designation: CCMT09T304-MM4 WSM01 Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombic 80° Plate size: 09 Plate thickness: T3 Special features Series: Tiger-tec Silver Grade: WSM01 (coated carbide) Chipbreaker: MM4 Material groups: S / M (superalloys, stainless steels) Tolerance class: M FAQ Which materials are suitable for this insert? The CCMT09T304-MM4 WSM01 insert from Walter Tools is suitable for stainless steels (M) and heat‑resistant superalloys/titanium (S) as indicated by its WSM01 grade and Tiger‑tec Silver series. What benefit does the MM4 chipbreaker provide? The MM4 chipbreaker on this insert improves chip formation and evacuation, helping to protect the cutting edge and stabilise the machining process during turning and boring operations. How does the 0.4 mm corner radius affect results? A 0.4 mm corner radius increases edge strength and supports consistent surface quality; it is a compromise that offers durability for moderate feeds while still enabling fine finishing where required. Is this insert compatible with standard CCMT tool-holders? Yes — the CCMT designation and insert size 09 correspond to common holder systems, but it is recommended to verify clamping geometry and seat angle before use. What series and coating does this grade belong to? This item is part of the Tiger‑tec Silver series and uses the WSM01 coated carbide grade, optimised for wear resistance and thermal stability in challenging materials. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T304-MM4 WSM10S MM4 Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Silver series and the WSM10S grade for reliable machining of stainless steels and heat-resistant alloys; the result is stable chip formation and extended edge life for continuous production. Order the insert directly via Metav Werkzeuge or consult our technical advisers for process-specific recommendations. CCMT09T304-MM4 WSM10S turning insert, rhombic 80° geometry, Walter Tools The CCMT09T304-MM4 WSM10S is a coated turning and boring insert designed for demanding work on stainless steels and superalloys, combining a wear-resistant coating with a robust chipbreaker for stable metal removal. Tiger·tec Silver coating for high wear resistance Grade WSM10S for stainless and superalloys Rhombic 80° CCMT shape for versatile turning MM4 chipbreaker with 0.4 mm corner radius Proven grade and coating for demanding alloys The combination of the Tiger·tec Silver coating and the WSM10S grade provides a balance between wear resistance and edge security that is particularly beneficial when machining stainless steels and heat‑resistant superalloys. The coated carbide construction reduces flank wear and helps maintain a consistent cutting edge under high temperatures, which leads to fewer tool changes and more predictable cycle times. This performance advantage translates directly into improved throughput and lower per‑part tooling costs. Geometry and chip control that support consistent processes The Rhombus 80° form of the insert, together with a 7° free angle and a modest 0.4 mm corner radius, gives a versatile cutting geometry that supports both finishing and medium‑duty roughing operations. The MM4 chipbreaker is engineered for secure chip formation when cutting tough materials, preventing long, stringy chips and promoting safe evacuation. The T3 thickness provides the rigidity needed to resist deflection during interrupted cuts, improving dimensional stability and surface quality. Industrial benefits for production environments Applied correctly in stable toolholders, this insert contributes to greater process reliability and a consistently high surface finish on parts made from challenging materials. The design reduces the risk of built‑up edge and thermal degradation at the cutting zone, which helps extend tool life and reduces unscheduled downtime. For workshop managers this means fewer tool interventions, steadier batch quality and easier planning of maintenance intervals. The CCMT09T304-MM4 WSM10S insert from Walter Tools is therefore suited to series production where reproducibility and tool life are priorities. Discuss machining requirements with Metav Werkzeuge to identify the optimal grades and geometries for a given application, or request a process review from our specialists at Metav Werkzeuge. Technical data SKU: CCMT09T304-MM4-WSM10S-WALTER Article: CCMT09T304-MM4 WSM10S Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Core specifications Free clearance angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Tolerance class: M Series: Tiger·tec Silver Design features Insert shape: Rhombus 80° Chipbreaker: MM4 Grade: WSM10S Material suitability: stainless steels (M), heat‑resistant superalloys/titanium (S) Material designation: coated carbide FAQ Which materials can be machined with this insert? The CCMT09T304-MM4 WSM10S insert from Walter Tools is specified for ISO group M (stainless steels) and S (heat‑resistant superalloys and titanium), making it suitable for demanding alloys that generate high temperatures and tend to work harden. What advantages does the Tiger·tec Silver series provide? Tiger·tec Silver coating on the WSM10S grade offers enhanced wear resistance and thermal stability, improving tool life and maintaining edge integrity during continuous turning operations. Is this insert suitable for both finishing and roughing? Yes. The Rhombus 80° geometry, combined with a 0.4 mm corner radius and the MM4 chipbreaker, allows the insert to perform well in finishing and moderate roughing tasks, depending on insert geometry and cutting parameters. How does the MM4 chipbreaker influence machining? The MM4 chipbreaker on the CCMT09T304-MM4 WSM10S promotes controlled chip formation for sticky or gummy materials, reducing the risk of long chips and enabling safer, more efficient material removal. What role does the 7° free angle and T3 thickness play? A 7° free angle helps reduce rubbing on the flank face, while the T3 thickness increases rigidity; together they support dimensional accuracy and resistance to vibration during interrupted or heavy cuts. Manufacturer/Responsible: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and registered trade names are used for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
CCMT09T304-MM4 WSM20S MM4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WSM20S grade for reliable performance in demanding materials, together with the MM4 chipbreaker for consistent chip control; order the insert directly via Metav Werkzeuge or contact the consultancy team for tailored process recommendations. CCMT09T304-MM4 WSM20S — Turning indexable insert, Tiger·tec Silver coating, Walter Tools The CCMT09T304-MM4 WSM20S is a rhombic 80° turning insert engineered for secure machining of rostfreier Stahl and heat‑resistant superalloys, combining a wear‑resistant grade with an optimised chip control geometry. Tiger·tec Silver coating for thermal stability Optimised MM4 chipbreaker for stable chips Rhombic 80° insert, 0.4 mm corner radius Robust cutting performance for difficult alloys and rostfreier Stahl The combination of the Tiger·tec Silver coating and the WSM20S carbide grade provides a significant improvement in thermal resistance and wear behaviour when machining rostfreier Stahl and other tough alloys. The multilayer coating reduces heat penetration to the carbide substrate and supports a stable cutting edge, which translates into longer tool life and fewer interruptions for insert changes. This technical advantage means smoother process windows when facing issues such as work hardening and built‑up edge, typical for these materials. Precision geometry that controls chips and improves surface quality The insert’s MM4 chipbreaker and Rhombic 80° form work together to deliver predictable chip formation and controlled evacuation during turning. The 0.4 mm corner radius and 7° clearance angle (freedom for clearance) offer a balance between edge strength and finishing capability, making the geometry suitable for medium to light roughing and semi‑finishing passes. The T3 thickness adds rigidity at the cutting edge, which helps maintain dimensional stability and contributes to improved component surface quality with fewer rework cycles. Productivity benefits and economical tool life By favouring stable chip control and high thermal stability, this insert reduces the risk of unplanned downtime and tool‑related rejects. The grade’s resistance to softening at elevated temperatures supports consistent cutting performance across longer running times, which yields better utilisation of machining centres and a lower cost per part in high‑mix production. The rhombic insert form also enables flexible indexing options, allowing multiple cutting edges per insert to be employed before disposal. Typical applications and process recommendations Designed for machining rostfreier Stahl and demanding superalloys (ISO groups M and S), the insert performs well where heat management and edge stability are critical. Preferred uses include interrupted and continuous turning of workpieces prone to strain‑hardening or thermal build‑up. For best results, pair the insert with a rigid toolholder, maintain stable cutting parameters, and use coolant strategies appropriate to the workpiece material and cycle times. For additional machining data or adaptation to a specific machine set‑up, Metav Werkzeuge offers technical support and material‑specific recommendations. Contact Metav Werkzeuge for tailored cutting data and to request the CCMT09T304-MM4 WSM20S insert from Walter Tools; phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Data SKU: CCMT09T304-MM4-WSM20S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCMT09T304-MM4 WSM20S Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Silver Grade: WSM20S Chipbreaker: MM4 Core technical values Clearance angle: 7° Corner radius: 0.4 mm Thickness: T3 Shape: Rhombus 80° Size designation: 09 Special features and applicability Coating: Tiger·tec Silver Carbide grade: WSM20S (coated cemented carbide) Material applicability: rostfreier Stahl; heat‑resistant superalloys and titanium (ISO groups M and S) Tolerance class: M Insert designation: CCMT09T304-MM4 FAQ Which materials are best machined with this insert? The CCMT09T304-MM4 WSM20S insert is intended primarily for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S); the WSM20S grade supports secure chip formation and edge stability in these challenging materials. What advantages does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on the WSM20S grade increases thermal resistance and reduces wear, which helps the CCMT09T304‑MM4 insert maintain a consistent cutting edge and extend useful tool life under elevated cutting temperatures. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker produces controlled chip shapes and improves evacuation, reducing the likelihood of chip entanglement and promoting steadier cutting forces; this benefits surface finish and reduces machine interruptions. Is the insert suitable for finishing passes? With a 0.4 mm corner radius and Rhombic 80° geometry, the insert is appropriate for semi‑finish and finish operations where a balance of edge strength and surface quality is required; final results depend on cutting parameters and holder rigidity. What is the full designation for ordering? Order under the designation CCMT09T304‑MM4 WSM20S (Walter Tools); the SKU is CCMT09T304‑MM4‑WSM20S‑WALTER. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Walter Tools is part of a leading group in precision machining solutions. Protected trademarks and product names belong to their respective owners. Mention of brand names serves explanation only; there is no affiliation between Metav Werkzeuge and the mentioned manufacturers. The offered item is original, factory‑new product of the manufacturer.
CCMT09T304-MM4 WSM30S MM4 Wendeplatten - Walter Tools
Take advantage of the combination of high thermal resistance, stable chip control, and proven insert geometry for dependable machining of stainless steels and heat-resistant alloys; order directly via Metav Werkzeuge or consult our specialists for application-matched advice. CCMT09T304-MM4 WSM30S turning and drilling indexable insert by Walter Tools — Tiger·tec Silver, MM4 chipbreaker CCMT09T304-MM4 WSM30S is an indexable insert designed for combined drilling/boring and turning applications, optimised for stainless steels and heat-resistant superalloys where heat resistance and edge stability are critical Tiger·tec Silver coating for heat resistance Optimised MM4 chip control Rhombic 80° form for versatile insert use 7° clearance with 0.4 mm corner radius High-temperature performance that stabilises the process The WSM30S grade from the Tiger·tec Silver series is a coated carbide solution engineered for materials that generate high cutting temperatures and tend to form built-up edge. Its microstructure and coating support a stable cutting edge and reduced adhesion, which in turn lowers the risk of premature wear and unplanned rework. As a result, the insert sustains consistent performance in interrupted cuts and demanding stainless steel operations while maintaining surface integrity. Geometry and chip control that improve productivity The Rhombic 80° insert geometry combined with the MM4 chipbreaker provides controlled chip formation across a range of feeds and depths of cut. The 7° clearance and 0.4 mm corner radius help to distribute cutting forces and reduce vibration, delivering a reliable balance between edge strength and surface finish. For shops seeking predictable chip flow and fewer machine stoppages, this geometry reduces manual chip handling and supports smoother cycle times. Practical specification for stable repeatability and handling Produced to tolerance class M, the insert’s T3 thickness and size 09 format make it compatible with a wide range of standard toolholders for drilling/boring and turning indexable applications. The combination of grade and form is tailored to deliver process reliability when machining rostfreier Stahl and heat-resistant alloys, offering an economical route to longer tool life and less frequent index changes. The insert’s characteristics simplify setup and reduce inspection time during production runs. For tailored selection support or to secure supply through Metav Werkzeuge, please contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for specialist advice and fast fulfilment. Technical Data Article number: CCMT09T304-MM4-WSM30S-WALTER Designation: CCMT09T304-MM4 WSM30S Series: Tiger·tec Silver Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Size: 09 Thickness: T3 Special features Coating / grade: WSM30S Chipbreaker: MM4 Material suitability: S / M Tolerance class: M Shape: Rhombic 80° Application: Designed for stainless steels and heat‑resistant superalloys FAQ Which materials are suitable for this insert? The CCMT09T304-MM4 WSM30S insert from Walter Tools is intended primarily for rostfreier Stahl (stainless steels) and heat‑resistant superalloys (ISO groups M and S), offering improved edge life in tough, heat‑generating materials. What benefits does the MM4 chipbreaker deliver? The MM4 chipbreaker on the CCMT09T304-MM4 WSM30S creates consistent chip segmentation and evacuation, which reduces machine downtime and improves surface finish during turning and drilling operations. Is the geometry suitable for both turning and boring? Yes — the Rhombic 80° form and the insert’s dimensions allow versatile use in both drilling/boring and turning applications, providing a balance between cutting edge strength and accessibility in a variety of toolholders. What does tolerance class M mean for shop practice? Tolerance class M indicates machining and seating accuracy appropriate for stainless and heat‑resistant materials, supporting repeatable clamping and minimal runout when fitted to compliant toolholders. How does the Tiger·tec Silver series affect tool life? The Tiger·tec Silver technology used on WSM30S enhances thermal stability and wear resistance, which typically leads to longer intervals between index changes and more stable performance in high‑temperature cutting scenarios. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original, factory‑new merchandise from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
CCMT09T304-MP4 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of the WEP10C cermet grade and the MP4 chipbreaker to achieve consistent finishing results with low wear; the rhombus 80° geometry and 7° relief angle support efficient edge life and stable cutting. Order the CCMT09T304-MP4 WEP10C inserts directly via Metav Werkzeuge or request application advice from the consultants. CCMT09T304-MP4 WEP10C cermet turning insert — Walter Tools, rhombus 80°, MP4 chipbreaker The CCMT09T304-MP4 WEP10C is a cermet indexable insert designed for precise finishing and semi-finishing turning operations where surface quality and repeatable edge life are required Walter Cermet grade WEP10C Rhombus 80° insert geometry MP4 chipbreaker for fine finishing 0.4 mm corner radius, 7° relief Consistent finishes through cermet performance The Walter Cermet WEP10C grade combines wear resistance with a fine cutting edge, making it particularly suited to finishing passes where surface integrity matters. As a cermet material, the grade offers improved hot hardness and edge stability compared with conventional carbides, which reduces built-up edge and helps maintain dimensional consistency. The result is a predictable tool life and improved batch-to-batch repeatability when the grade is applied in the correct cutting window. Suitability across workpiece materials should be verified in the product matrix to ensure the best match for the intended application. Machining advantages from geometry and chip control The rhombus 80° geometry provides a good balance between tool strength and access to the cutting zone, while the MP4 chipbreaker is optimised for fine finishing, producing short, manageable chips under light to moderate depths of cut. The modest 0.4 mm corner radius supports delicate edge transitions, enhancing surface finish without compromising edge stability. The 7° relief angle reduces rubbing at the flank face, lowering cutting forces in finishing passes and contributing to improved workpiece surface quality. Together, these attributes make the insert an effective choice where consistent finishes and reliable chip control are priorities. Practical integration and economic handling in the toolroom Designed as an indexable turning insert with designation CCMT, the component fits standard toolholders and is available in thickness code T3, tolerance class M, and plate size 09, enabling straightforward replacement and inventory management. The cermet grade and chipbreaker combination reduce the need for frequent re-grind cycles, supporting efficient shop-floor workflows and predictable tool-change planning. For application-specific recommendations or assistance with holder selection, Metav Werkzeuge provides tailored advice and can supply compatible components to ensure rapid integration into existing turning systems. Contact Metav Werkzeuge for tailored tooling recommendations and fast availability of Walter Tools CCMT inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T304-MP4-WEP10C-WALTER Designation: CCMT09T304-MP4 WEP10C Label: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCMT09T304-MP4 WEP10C Walter Tools Manufacturer: Walter Tools Series: Walter Cermet Facts Relief angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 80° Plate size: 09 Thickness: T3 Tolerance class: M Special features Grade: WEP10C (cermet) Chipbreaker: MP4 Execution: T Material: Katalogabhängig ISO designation: CCMT09T304-MP4 WEP10C FAQ What materials is this insert best suited to? The CCMT09T304-MP4 WEP10C insert uses a cermet grade that is optimised for finishing applications; material suitability should be checked against the product matrix to confirm compatibility with specific steels, alloys or other workpiece materials. How does the MP4 chipbreaker affect surface finish? The MP4 chipbreaker is designed for fine finishing, promoting short chip formation and stable cutting conditions that contribute to a consistent surface quality when using the CCMT09T304-MP4 WEP10C insert. Can the rhombus 80° geometry be used for light profiling? Yes, the rhombus 80° geometry offers a good compromise between cutting edge access and robustness, making it suitable for light profiling and finishing passes where controlled cutting engagement is required. What does the thickness code T3 indicate for tool mounting? The T3 thickness designation indicates the insert thickness series and ensures compatibility with toolholders specified for that thickness; verify holder compatibility to maintain clamping integrity and repeatable performance. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com
CCMT09T304-MP4 WPP10G - Walter Tools
Combine the Tiger·tec Gold coating with the MP4 chipbreaker and the compact Rhombus 80° geometry to achieve reliable steel machining and consistent surface quality; order the CCMT09T304‑MP4 WPP10G through Metav Werkzeuge or consult the technical advisors for application support. CCMT09T304-MP4 WPP10G – Rhombic 80° turning/boring insert, Tiger·tec Gold (Walter Tools) The CCMT09T304‑MP4 WPP10G is a coated carbide indexable insert for turning and boring steel, designed for stable chip formation and long tool life in general steel applications. Tiger·tec Gold coating technology Designed for steel machining (ISO P) MP4 chipbreaker for controlled chip formation 0.4 mm corner radius for consistent surface finish Optimised performance for steel turning operations The combination of Tiger·tec Gold coating and a dedicated MP4 chipbreaker provides a balance between wear resistance and consistent chip control, which helps maintain cutting performance over longer cycles. The coating improves thermal stability and reduces flank wear during continuous operation, while the chipbreaker is shaped to manage chip flow in typical steel cutting conditions. For shops aiming to increase uptime and reduce insert change frequency, this geometry delivers a measurable improvement in process stability and predictable tool life. Geometry that protects the workpiece and supports surface quality A Rhombus 80° form with a 0.4 mm corner radius gives a robust cutting edge that supports moderate finishing and semi‑roughing passes without excessive deflection. The nominal 7° clearance angle reduces rubbing on the flank while maintaining effective cutting engagement, which translates into consistent surface finish and reduced risk of built‑up edge when machining unalloyed and alloyed steels. The insert’s design helps achieve reproducible results across tool changes and operators. Practical benefits for production planning and tool selection The insert’s designation and tolerance class (M) support straightforward interchangeability in established toolholder systems that accept CCMT‑type inserts. The T3 thickness designation and size code 09 make it compatible with common clamping tools, simplifying inventory management. Specifying a coated, industry‑grade insert like this one can reduce the frequency of regrinds and the number of different grades held in stock, yielding a clearer cost‑benefit in medium‑ to high‑volume turning operations. Material suitability and application guidance This grade, WPP10G, is formulated for steel (ISO P) and offers an application range from wear‑resistant to universal to tougher grades as denoted by the manufacturer’s classification. The coated carbide substrate resists abrasive wear and thermal softening during typical speeds for steel turning. Use the insert where reliable chip control and repeatable surface quality are priorities, for instance in longitudinal turning, light profiling and certain boring operations where CCMT geometry fits the toolholder. For stainless or specialised alloys, select a grade specified for those materials. Discuss Walter Tools Tiger·tec Gold applications with Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations and application advice Technical data Article number: CCMT09T304-MP4-WPP10G-WALTER Designation: CCMT09T304‑MP4 WPP10G Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness designation: T3 Special features Series: Tiger·tec Gold Grade: WPP10G (coated carbide) Chipbreaker: MP4 Insert shape: Rhombus 80° Tolerance class: M FAQ Which materials is this insert intended for? The CCMT09T304‑MP4 WPP10G is intended for steel machining (ISO P) and is optimised for unalloyed and alloyed steels. What advantages does the Tiger·tec Gold series provide? Tiger·tec Gold coating offers improved thermal resistance and reduced flank wear, enhancing the insert’s performance in continuous steel turning operations. How does the MP4 chipbreaker influence machining? The MP4 chipbreaker on this indexable insert promotes controlled chip formation and safe evacuation, supporting reliable production cycles when machining steel. Is the insert suitable for finishing passes? With a 0.4 mm corner radius and Rhombus 80° geometry, the insert is suited to light finishing and semi‑finishing cuts that prioritise surface consistency. What does the tolerance class M indicate? Tolerance class M denotes a medium tolerance level for dimensional accuracy, ensuring good repeatability when swapping inserts in compatible CCMT toolholders. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only and do not imply any affiliation with our company. The offered item is an original, factory‑new product of the manufacturer Walter Tools. The Walter brand is part of the Walter AG group and is presented here for identification and technical clarity.
CCMT09T304-MP4 WPP20G WPP20G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Gold coating and the WPP20G universal grade for efficient steel machining; the CCMT geometry with a 0.4 mm corner radius and 7° clearance delivers consistent chip control and dependable tool life. Order directly via Metav Werkzeuge or consult their specialists for matching insert and holder recommendations. CCMT09T304-MP4 WPP20G – Indexable turning insert, Tiger‑tec Gold coating for steel (Walter Tools) A CCMT09T304‑MP4 WPP20G indexable turning insert engineered for productive steel turning, combining a Tiger‑tec Gold coated carbide grade with an MP4 chipbreaker and rhombic 80° geometry for versatile operations Tiger‑tec Gold coating for improved tool life Universal WPP20G grade optimised for steel Rhombic 80° geometry for versatile turning MP4 chipbreaker for reliable chip control High productivity through a coated grade optimised for steel The Tiger‑tec Gold coating in combination with the WPP20G grade provides a wear‑resistant, coated carbide substrate that is tailored to the heat and chip formation typical of steel machining. This combination promotes stable chip formation and extended tool life, which reduces changeover frequency and supports continuous production. The result is a measurable improvement in process efficiency and predictable machining outcomes when turning unalloyed and alloyed steels. Geometry and chip control that support consistent surface quality Rhombic 80° geometry paired with the MP4 chipbreaker yields flexible approach angles and dependable chip guidance across a range of turning tasks. The insert’s 0.4 mm corner radius and 7° clearance contribute to controlled engagement and a fine surface finish in finishing passes, while also enabling short‑chipping conditions in semi‑roughing. The chipbreaker design assists in breaking and evacuating chips reliably, lowering the risk of built‑up edge and protecting the workpiece from rework. Practical fit for workshop toolsets and process security With a standard insert size designation and T3 thickness in tolerance class M, the insert integrates into common indexable turning toolholders for straight‑forward set‑up. The universal characteristics of the grade support a broad spectrum of steel applications, delivering process security and repeatable results. Operators benefit from reduced downtime due to predictable wear behaviour and easy placement into existing tool systems, supporting both small batch and higher volume production runs. For application advice or to secure compatible toolholders for Walter Tools’ Tiger‑tec Gold inserts, contact Metav Werkzeuge for tailored recommendations at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: CCMT09T304-MP4-WPP20G-WALTER Designation: CCMT09T304-MP4 ISO designation: CCMT09T304-MP4 WPP20G Manufacturer: Walter Tools Grade: WPP20G Series: Tiger‑tec Gold Facts Relief angle: 7° Corner radius: 0.4 mm Insert form: Rhombic 80° Insert size: 09 Thickness: T3 Tolerance class: M Special features Coating: Tiger‑tec Gold (coated carbide) Chipbreaker: MP4 Geometry: Rhombic 80° Material application: Steel FAQ What materials is this insert intended for? The insert is specified for machining steel; the WPP20G grade is formulated to manage the heat and chip formation typically encountered when turning unalloyed and alloyed steels. How does the MP4 chipbreaker affect machining? The MP4 chipbreaker is designed to produce short, controllable chips and aid safe evacuation, improving process stability and surface finish during both semi‑finishing and finishing turns. Is the 0.4 mm corner radius suitable for finishing? A 0.4 mm corner radius balances edge strength and surface quality, making it suitable for fine finishing passes where a good surface is required while maintaining sufficient robustness. What does tolerance class M indicate for this insert? Tolerance class M denotes standard manufacturing tolerances for the insert dimensions, supporting consistent seating and repeatable positioning in compatible toolholders. Can this insert be used in existing toolholders? The insert follows common CCMT form and size conventions and, given the stated thickness T3 and rhombic geometry, is compatible with standard indexable turning toolholders designed for CCMT inserts. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation between Metav Werkzeuge and the trademark owners. The offered item is an original, factory‑new product from the manufacturer.
CCMT09T304-MP6 WPP10G Wendeplatten - Walter Tools
High wear resistance and predictable chip control from the Tiger·tec Gold grade combine with a compact MP6 chipbreaker and a 0.4 mm corner radius for reliable finishing of steel components. Order the insert directly via Metav Werkzeuge or consult their specialists for application-specific recommendations. CCMT09T304-MP6 WPP10G turning insert — MP6 chipbreaker, Rhombus 80°, Walter Tools The CCMT09T304-MP6 WPP10G is a rhombic 80° turning insert designed for efficient machining of steel in serial and finishing applications. Tiger·tec Gold coating for longer life MP6 chipbreaker for reliable chip control 0.4 mm corner radius for fine finishing Rhombic 80° form with 7° clearance Consistent productivity for steel turning The CCMT09T304-MP6 WPP10G delivers a balance of tool life and cutting performance thanks to the combination of the Tiger·tec Gold coating and a purpose-built MP6 chipbreaker. The coated carbide substrate stabilises the cutting edge under thermal load, which reduces flank wear and supports steady cutting conditions over longer cycles. For production environments this translates into fewer tool changes and more consistent component tolerances, improving throughput without sacrificing surface quality. Coating and material compatibility explained The insert is a coated carbide grade optimised for the ISO group P (steel). The Tiger·tec Gold technology combines wear-resistant layers with controlled adhesion to combat built-up edge and maintain a sharp cutting line at elevated temperatures. For machinists working with unalloyed or alloyed steel, this means improved resistance to abrasion and thermal softening. The result is predictable cutting behaviour and a reduced risk of unexpected rework in batch manufacturing. Geometry that enhances finish and reliability A rhombic 80° form with a 0.4 mm corner radius and a 7° clearance angle provides a compromise between strength and finesse. The moderate corner radius aids in producing a smooth surface finish while maintaining edge stability during interrupted cuts; the MP6 chipbreaker guides chips away from the cutting zone to prevent re-cutting. The plate thickness T3 and tolerance class M support repeatable clamping and dimensional conformity in automated toolholders, helping to protect both insert and workpiece integrity. Economic benefits and process integration Selecting this grade and geometry supports a cost-effective machining strategy: longer edge life reduces consumable spend, while consistent chip control lowers cleaning and machine downtime. The insert interfaces seamlessly with standard CCMT toolholders, allowing swift integration into existing setups. For manufacturers seeking steady results in serial turning of steel components, the combination of Tiger·tec Gold, MP6 chip control and robust geometry yields measurable gains in productivity and quality. Discuss machining parameters with Metav Werkzeuge to exploit Tiger·tec Gold performance for steel turning; contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: CCMT09T304-MP6-WPP10G-WALTER Product: Turning insert Designation: CCMT09T304-MP6 WPP10G Brand: Walter Tools Series: Tiger·tec Gold Facts Corner radius: 0.4 mm Clearance angle: 7° Insert size: 09 Plate thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold Material: coated carbide Chipbreaker: MP6 Suitable for: steel (ISO P) Shape: Rhombus 80° Series/sort description: WPP10G (wear-resistant grade for steel machining) FAQ What materials is this insert suitable for? The CCMT09T304-MP6 WPP10G turning insert (Walter Tools) is specified for steel machining under ISO group P and is designed to handle typical heat and chip formation encountered with unalloyed and alloyed steels. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating on the CCMT09T304-MP6 WPP10G reduces abrasive wear and improves thermal stability of the cutting edge, resulting in longer tool life and more consistent surface quality when turning steel. Which chipbreaker is fitted and what is its benefit? This insert uses the MP6 chipbreaker, which promotes controlled chip formation and evacuation, lowering the risk of chip entanglement and improving process reliability during continuous turning operations. Is the insert compatible with standard CCMT toolholders? Yes, the geometry and T3 thickness of the CCMT09T304-MP6 WPP10G are compatible with standard CCMT toolholders, enabling straightforward replacement and integration into existing turning setups. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T304-MP6 WPP20G Wendeplatten - Walter Tools
The combination of Tiger‑tec Gold coating and the MP6 chipbreaker ensures consistent edge life and stable chip control for steel turning; the rhombic 80° geometry with a 0.4 mm corner radius delivers improved surface finish and reliable process results. Order directly via Metav Werkzeuge or consult our advisers for application-specific recommendations. CCMT09T304-MP6 WPP20G Walter Tools — indexable turning insert with Tiger‑tec Gold coating for steel The CCMT09T304-MP6 WPP20G is an indexable turning insert engineered for productive steel machining, combining a robust MP6 chipbreaker with the Tiger‑tec Gold coated grade for long tool life. Tiger‑tec Gold coating for extended lifetime MP6 chipbreaker for stable chip control Rhombic 80° geometry for versatile turning Deliver consistent edge life and predictable machining economy The Tiger‑tec Gold coating and the WPP20G grade provide wear resistance and thermal stability designed specifically for machining steel (ISO P). This combination reduces flank wear and prolongs cutting-edge service life, which contributes directly to lower tool-change frequency and improved overall machining economy. Coated carbide grades such as this are optimised for the heat and chip formation typical when turning unalloyed and alloyed steels, resulting in reproducible performance across batch and single‑piece production. Achieve reliable chip control and improved surface quality The MP6 chipbreaker is tuned to produce short, manageable chips on typical steel turning tasks, reducing the risk of chip entanglement and supporting uninterrupted cycle times. Together with the 0.4 mm corner radius and the 7° clearance angle, the geometry helps to produce stable cutting forces and a finer surface finish. The rhombic 80° form gives a balanced mix of cutting-edge strength and accessibility for medium‑depth turning operations, enabling clean finishes with reduced vibration. Versatile insert design for workshop efficiency The insert’s shape and size designation (09, thickness T3) make it compatible with a wide range of standard toolholders, simplifying stocking and tool‑holder logistics on the shop floor. The tolerance class M ensures dependable interchangeability between inserts, supporting consistent set‑up and repeatable results. Designed for steel applications, this insert suits both serial production and flexible jobbing environments where process reliability and predictable tool behaviour are essential. Practical advantages at the machine and in procurement As an indexable insert, the item removes the need for regrinding and simplifies tool inventory management: only the worn insert is replaced, not the entire tool. The coated grade’s emphasis on stable chip formation and good edge retention reduces downtime and permits longer uninterrupted runs. For application matching, the grade is particularly suited to the typical heat generation and chip characteristics when turning steel, facilitating straightforward selection and predictable machining performance. For tailored advice on optimising Walter Tools Tiger‑tec Gold inserts for steel turning, contact Metav Werkzeuge to discuss tooling strategies and application-specific recommendations. Technical data Article number: CCMT09T304-MP6-WPP20G-WALTER Designation: CCMT09T304-MP6 Full designation: CCMT09T304-MP6 WPP20G Series: Tiger‑tec Gold Manufacturer: Walter Tools Core technical data Size: 09 Thickness: T3 Corner radius: 0.4 mm Clearance angle: 7° Geometry: Rhombic 80° Grade: WPP20G Chipbreaker: MP6 Tolerance class: M Special features Coating: Tiger‑tec Gold Applicable material group: Steel (ISO P) Execution/style: T Optimised for stable chip formation and productive machining FAQ What materials is this insert intended for? The CCMT09T304‑MP6 WPP20G insert is specified for machining steel (ISO P) and is designed to handle the heat and chip formation typical of unalloyed and alloyed steels. How does the MP6 chipbreaker affect machining? The MP6 chipbreaker promotes short, controllable chips and steady cutting forces, which supports continuous machining and reduces the chance of chip-related interruptions when using this Walter Tools insert. Can the insert be used for finishing operations? With a 0.4 mm corner radius and the rhombic 80° geometry, the insert suits medium finishing and general turning tasks, providing a good balance between surface quality and edge strength. What benefits does the Tiger‑tec Gold coating provide? Tiger‑tec Gold coating on the WPP20G grade enhances wear resistance and thermal stability during steel turning, improving edge life and enabling more predictable tool performance. Is the insert compatible with standard toolholders? The 09 size and T3 thickness correspond to common indexable insert standards, making the component compatible with a wide range of standard turning toolholders engineered for CCMT‑style inserts. Markennamen und geschützte Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
CCMT09T304-MP6 WPP30G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating, the MP6 chipbreaker geometry and the robust rhombic 80° form delivers reliable edge life and consistent chip control for steel machining. Order the insert directly via Metav Werkzeuge or consult our specialists for process optimisation and cutting data. CCMT09T304-MP6 WPP30G — Indexable turning insert, Tiger·tec Gold coating, for steel (Walter Tools) The CCMT09T304-MP6 WPP30G is a rhombic 80° indexable turning insert engineered for steel machining, offering coated carbide wear resistance and a geometry optimised for stable chip formation. Tiger·tec Gold coating for long tool life Optimised chip control MP6 geometry Rhombic 80° CCMT form, 7° relief Suitable for steel machining (ISO P) Maximised tool life and dependable process security The combination of the Tiger·tec Gold coating and the WPP30G grade creates a surface treatment and substrate pairing that resists abrasive and adhesive wear during the cyclic heat loads typical of steel turning. As a coated carbide insert, it offers predictable flank wear progression, which supports longer periods between tool changes and more consistent part quality. The economical performance of this grade is reflected in stable cutting results under standard finishing and medium-cutting conditions, making it suitable for production environments that prioritise uptime and repeatability. Precise chip control for consistent surface finish The MP6 chipbreaker geometry is developed to manage chips in common steel applications, reducing the risk of snarled swarf and improving evacuation at moderate feed rates. The CCMT rhombic 80° form with 7° relief and a 0.4 mm corner radius balances cutting-edge strength and accessibility for entering contours and shoulders. The controlled chip formation contributes directly to a consistent surface finish and lowers the likelihood of built-up edge, which in turn reduces scrap rates and downstream rework in series machining. Practical guidance for steel machining and application scope Designed for the ISO P group, this insert performs well on unalloyed and alloyed steel, where typical thermal and metallurgical conditions demand a resilient grade. The T3 insert thickness yields good rigidity in standard toolholders while the rhombic geometry facilitates indexability and economical corner usage. For roughing to finishing operations, select feeds and depths that match the toolholder stiffness and machine power; the grade’s behaviour supports a broad window of cutting parameters, helping to simplify tool selection across mixed steel jobs. For tailored recommendations on Walter Tools inserts with Tiger·tec Gold coating, contact Metav Werkzeuge for application advice and availability: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: CCMT09T304-MP6-WPP30G-WALTER Label: Drehwendeschneidplatte CCMT09T304-MP6 WPP30G Walter Tools Product type: Drehwendeschneidplatte (indexable turning insert) Manufacturer: Walter Tools ISO designation: CCMT09T304-MP6 WPP30G Facts Relief angle: 7° Corner radius: 0.4 mm Shape: Rhombic 80° Insert size: 09 Thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold Carbide grade: WPP30G (coated carbide) Chipbreaker: MP6 Application: Steel (ISO P) Series: Tiger-tec Gold Geometry: CCMT rhombic 80° FAQ What steels is this insert best suited for? The CCMT09T304-MP6 WPP30G is designed for ISO P materials and performs reliably on unalloyed and alloyed steel where typical heat and chip behaviour occurs. How does the MP6 chipbreaker affect machining? The MP6 geometry promotes controlled chip formation and evacuation in steel turning, which supports consistent surface quality and reduces the risk of chip-related interruptions. What does the WPP30G grade provide? WPP30G, part of the Tiger·tec Gold series, offers a balanced combination of wear resistance and toughness for productive machining across a broad range of steel applications. Which features improve edge stability during interrupted cuts? The rhombic 80° CCMT form, the 0.4 mm corner radius and the coated-carbide substrate together enhance edge strength and resistance to impact during light interruptions and entry cuts. Can this insert be indexed to use multiple cutting corners? Yes, the CCMT form allows indexing to utilise several corners, helping to extend usable tool life and reduce tooling costs per part. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T304-MW4 WKK20S Wendeplatten - Walter Tools
Benefit from the Tiger‑tec Silver coating and the MW4 chipformer for productive, abrasion‑resistant cast‑iron turning; order the CCMT09T304‑MW4 WKK20S insert directly via Metav Werkzeuge or consult our specialists for application advice. CCMT09T304-MW4 CCMT09T304-MW4 WKK20S indexable turning insert for cast iron — Walter Tools A robust CCMT09T304‑MW4 WKK20S indexable turning insert optimised for efficient machining of cast‑iron components in industrial turning applications Tiger‑tec Silver coating for long tool life Optimised MW4 chipformer for short chips 7° clearance angle, 0.4 mm corner radius Rhombic 80° shape for versatile turning Increased productivity through advanced coating and chip control The combination of the Tiger‑tec Silver coating and the WKK20S grade delivers enhanced resistance to abrasive wear and improved edge stability when machining cast iron. The coated carbide substrate is formulated for the specific demands of grey and nodular cast irons, which typically produce short, brittle chips. The integrated MW4 chipformer supports consistent chip breaking, reducing interruptions and increasing machining uptime. As a result, cycle times are shortened and tool change frequency is reduced, supporting a more productive turning process. Reliable surface quality and robust edge geometry The rhombic 80° geometry with a 0.4 mm corner radius provides a balanced combination of strength and finishing capability: the radius reinforces the cutting edge for interrupted cuts while still enabling good surface finish on workpieces. The modest 7° clearance angle minimises rubbing and helps maintain stable cutting conditions over longer tool life. A tolerance class M ensures repeatable seat fit and positioning in standard toolholders, supporting process stability and predictable results in series production. Versatile, application‑oriented design for shopfloor use Designed as an indexable turning insert, the plate format (size 09, thickness T3) and the rhombic form make it suitable for a range of turning tasks, from roughing to finishing passes in cast‑iron components. The grade and geometry combination favours short, easily controlled chips, which helps to keep the machining area clean and reduces rework risk. The insert is compatible with standard clamping systems and is a practical choice where consistent chip control and tool life are priorities. For further technical clarification or recommendations on parameter settings, Metav Werkzeuge provides detailed consultation by email or phone. For productive cast‑iron turning with Walter Tools' proven Tiger‑tec Silver grade, contact Metav Werkzeuge for ordering and tailored technical advice: info@metav-werkzeuge.com, +49 2822 7131930. Technical data Article number: CCMT09T304-MW4-WKK20S-WALTER Designation: CCMT09T304-MW4 WKK20S Product type: Indexable turning insert (drehwendeschneidplatte) Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Plate size: 09 Plate thickness: T3 Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKK20S (coated carbide) Chipformer: MW4 Plate form: Rhombic 80° Material application: Cast iron (K) Robust cutting edge for interrupted cuts FAQ What materials is this insert designed for? The CCMT09T304‑MW4 WKK20S from Walter Tools is designed primarily for cast iron machining and is optimised for the abrasive wear and short chip behaviour typical of these materials. How does the MW4 chipformer affect machining? The MW4 chipformer produces reliably short chips in cast‑iron turning, reducing chip control issues and improving process continuity when using the CCMT09T304‑MW4 WKK20S insert. Which toolholders are compatible with this insert? The rhombic 80° format and tolerance class M ensure compatibility with standard indexable turning toolholders that accept CCMT‑style inserts; correct clamping and seat condition remain essential for optimal performance. What benefits does the Tiger‑tec Silver coating provide? Tiger‑tec Silver coating improves abrasion resistance and edge life under the high‑wear conditions of cast‑iron turning, enhancing productivity and reducing tool change frequency for the Walter Tools insert. Can this insert be used for finishing cuts? Yes; the 0.4 mm corner radius and rhombic geometry balance edge strength and surface finish capability, making the insert suitable for both roughing and certain finishing passes in cast iron. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are used for explanatory purposes only. There is no connection between our company and the mentioned brands. The item offered is original, brand‑new merchandise from the manufacturer.
CCMT09T304-MW4 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of Tiger·tec Gold performance and the WPP10G grade for stable chip formation and extended tool life in Stahl turning operations; the combination of a reliable MW4 chipbreaker, a 7° clearance angle and a 0.4 mm corner radius supports consistent surface quality and process security. Order the insert directly via Metav Werkzeuge or request application advice from the consultants. CCMT09T304-MW4 WPP10G – Turning indexable insert for Stahl | Walter Tools The CCMT09T304-MW4 WPP10G is a rhombic 80° coated-carbide turning insert optimised for general-purpose Stahl machining, combining Tiger·tec Gold coating with a robust chipbreaker for reliable production. Tiger·tec Gold coating for high wear resistance MW4 chipbreaker for consistent chip control 7° clearance angle for secure cutting action Rhombic 80° form with 0.4 mm corner radius Boosted tool life through advanced coating technology The Tiger·tec Gold coating and the WPP10G grade are engineered for high wear resistance under the thermal and mechanical loads typical of ISO P applications. Because the cut is influenced by temperature and friction, the coated-carbide chemistry reduces flank wear and prolongs tool life, which in turn lowers machining costs and increases uptime. The coated surface also contributes to consistent edge behaviour, enabling predictable dressing intervals and fewer unscheduled tool changes. Stable cutting geometry for improved surface quality The insert’s Rhombic 80° geometry combined with the 0.4 mm corner radius and 7° clearance angle provides a balance between strength and finish. The MW4 chipbreaker promotes short, controllable chips in a range of cutting conditions, which reduces the risk of surface damage and improves process security. The plate thickness T3 ensures sufficient edge support, minimising vibration and helping to maintain dimensional repeatability in serial turning operations. Broad applicability and productivity in Stahl machining Designed for the ISO P material group, the insert covers a spectrum from wear-resistant to tougher Stahl ranges, as described in the Tiger·tec Gold series classification. The combination of geometry and grade supports both finish and light-medium roughing passes, allowing productive tool use across common turning tasks. Process planners will appreciate the predictable chip control and robust edge life, which simplify cutting-parameter selection and reduce downtime for regrinding or replacement. Contact Metav Werkzeuge for application-specific recommendations on Walter Tools Tiger·tec Gold inserts and to arrange supply of the CCMT09T304-MW4 WPP10G; specialists are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: CCMT09T304-MW4-WPP10G-WALTER Designation: Drehwendeschneidplatte CCMT09T304-MW4 WPP10G Walter Tools Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Plate form: Rhombus 80° Size: 09 Corner radius: 0.4 mm Clearance angle: 7° Thickness: T3 Chipbreaker: MW4 Tolerance class: M Special features Grade: WPP10G Coating: Tiger·tec Gold (coated carbide) Material group: ISO P (Stahl) Execution: T Series notes: Optimised for stable chip formation and broad Stahl coverage FAQ What materials is this insert suitable for? The CCMT09T304-MW4 WPP10G from Walter Tools is specified for the ISO P material group and is therefore suitable for machining a wide range of Stahl grades. How does the MW4 chipbreaker affect performance? The MW4 chipbreaker on this insert promotes short, controllable chips and consistent chip flow, improving surface quality and reducing the risk of chip-related interruptions during turning with the CCMT09T304-MW4 WPP10G. Which advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold coating on the WPP10G grade enhances wear resistance and edge stability under elevated temperatures, resulting in longer tool life and more predictable machining performance in Stahl turning. Is the 0.4 mm corner radius suitable for finishing? A 0.4 mm corner radius offers a compromise between strength and finish: the radius supports a stable cutting edge while enabling a good surface result in light to medium finishing passes with the CCMT09T304-MW4 WPP10G. Can this insert be used for roughing and finishing operations? Yes, the combination of geometry, T3 thickness and the WPP10G grade allows the insert to be applied for both productive roughing and reliable finishing in many Stahl turning scenarios. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, brand-new product from the manufacturer.
CCMT09T304-MW4 WPP20G Wendeplatten - Walter Tools
Taking advantage of the Tiger·tec Gold coating and the MW4 chipbreaker, this turning insert combines long tool life with reliable chip control for steel machining; order directly via Metav Werkzeuge or request application advice from the technical team. CCMT09T304-MW4 WPP20G turning insert — Tiger·tec Gold, Walter Tools A CCMT09T304-MW4 WPP20G indexable turning insert engineered for robust ISO P (steel) machining with a Tiger·tec Gold coated carbide grade. Tiger·tec Gold coating for long tool life Stable chip formation with MW4 breaker Rhombic 80° geometry for versatile turning Extended tool life from advanced coating technology The Tiger·tec Gold coating combined with the WPP20G coated carbide grade delivers a balance of wear resistance and toughness tailored for steel machining. This composition reduces flank and crater wear under the thermal and mechanical loads typical for ISO P materials, resulting in fewer indexings and longer intervals between tool changes. The outcome is a measurable improvement in uptime and a lower cost per machined component, especially in high-volume turning operations. Reliable chip control and consistent surface quality Designed with a MW4 chipbreaker and Rhombic 80° CCMT geometry, the insert promotes predictable chip formation and stable cutting forces. The 0.4 mm nose radius and 7° clearance angle help maintain radial stability and produce consistent surface finishes during finishing and medium-turning passes. Clear chip evacuation reduces the risk of built-up edge and improves process security when machining unalloyed and alloyed steels. Versatile use for a broad range of steel applications Classified for ISO P materials, this grade is suited to conventional unalloyed and alloyed steels where a combination of wear resistance and edge robustness is required. The grade’s composition supports a wide cutting window, enabling productive cutting parameters across roughing and finishing steps. Choosing this indexable insert contributes to stable cycle times and predictable part quality in mixed-batch production. Compact specification that simplifies tool selection With the CCMT09 format, T3 thickness and the CCMT-style insert geometry, the component fits common turning toolholders that accept CCMT inserts, facilitating fast tooling changes. The moderate 0.4 mm corner radius offers a compromise between strength and finish capability, making this insert suitable where reliable performance and surface integrity are priorities rather than extreme radii or special contours. Contact Metav Werkzeuge to discuss process optimisation with Walter Tools Tiger·tec Gold inserts and secure consistent machining results Technical Data Article number / SKU: CCMT09T304-MW4-WPP20G-WALTER Designation: CCMT09T304-MW4 WPP20G Range / Series: Tiger-tec Gold Grade / Sort: WPP20G Manufacturer: Walter Tools Core Data Free angle: 7° Nose / corner radius: 0.4 mm Plate form: Rhombic 80° Plate size: 09 Plate thickness: T3 Tolerance class: M Special features Chipbreaker: MW4 Material group: P (Steel) Suitable for: Steel (ISO P) Intended application: Turning / indexable insert Base material: Coated carbide (Tiger·tec Gold technology) FAQ Which materials can be machined with this insert? The CCMT09T304-MW4 WPP20G insert is specified for ISO P materials and is optimised for machining unalloyed and alloyed steel grades. What benefit does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WPP20G grade enhances wear resistance while retaining edge toughness, improving tool life and consistency in steel turning applications under variable cutting conditions. Is this insert suitable for finishing operations? Yes; with a 0.4 mm corner radius and the MW4 chipbreaker, the insert supports good surface finishes on finishing passes while maintaining edge security. Does the CCMT09T304-MW4 fit standard CCMT toolholders? The CCMT09 format conforms to common CCMT geometries and is compatible with toolholders designed for CCMT indexable inserts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The described item is an original, factory‑new product of the manufacturer.
CCMT09T304-MW4 WSM20S MW4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WSM20S grade and the MW4 chipbreaker for secure chip control and extended tool life; this insert suits demanding turning in stainless steel and heat‑resistant superalloys. Order the CCMT09T304‑MW4 WSM20S directly via Metav Werkzeuge or ask the consultants for application support. CCMT09T304‑MW4 WSM20S — Rhombic 80° turning insert with Tiger·tec Silver, Walter Tools The CCMT09T304‑MW4 WSM20S is a coated turning insert designed for productive machining of stainless steel and heat‑resistant superalloys in industrial turning applications. Tiger·tec Silver coating for heat resistance WSM20S grade for stainless steel & superalloys Rhombic 80° form, 7° relief for versatile turning MW4 chipbreaker for consistent chip control High‑temperature cutting performance for demanding alloys The combination of the Tiger·tec Silver coating and the WSM20S carbide grade provides improved resistance to thermal loading and abrasion when machining tough materials. The coating technology enhances heat management at the cutting edge, while the grade is tuned for stable edge life during the interrupted cutting and high temperatures typical of stainless steel and nickel‑base alloys. As a result, the indexable insert delivers a reliable balance between wear resistance and toughness, reducing unplanned tool changes and supporting consistent production throughput. Geometry tuned for stability and surface quality The rhombic 80° shape with a 0.4 mm corner radius and a 7° relief angle offers a versatile geometry for general turning tasks and finishing passes. The moderate corner radius helps to maintain a strong cutting edge without sacrificing surface finish, and the relief angle reduces rubbing on the flank to lower cutting temperatures. The MW4 chipformer actively shapes chips for predictable evacuation, which lowers the risk of built‑up edge and improves process security. Together these features promote repeatable part quality and longer indexable insert life. Practical benefits and process recommendations Configured as a standard turning insert in size 09 with thickness T3, this solution integrates easily into common toolholders and machining setups. The combination of coating, grade and chip control targets operators who require productivity and reproducible results in mixed‑batch or series production. For roughing of heavy cross‑sections, consider conservative feeds to preserve the cutting edge; for finishing, the insert geometry supports superior surface integrity on stainless steel. The tolerance class M indicates suitability for applications where consistent insert geometry is essential for precision turning. For machining stainless steel and high‑temperature superalloys, contact Metav Werkzeuge for tailored cutting data and secure the Walter Tools CCMT09T304‑MW4 WSM20S insert to increase process stability and tool life. Technical data Article number: CCMT09T304‑MW4‑WSM20S‑WALTER Name: Drehwendeschneidplatte CCMT09T304‑MW4 WSM20S Walter Tools Type: Drehwendeschneidplatte Manufacturer: Walter Tools Facts Grade: WSM20S Coating series: Tiger·tec Silver Relief angle: 7° Corner radius: 0.4 mm Insert size: 09 Thickness: T3 Special features Chipbreaker: MW4 Shape: Rhombic 80° Material suitability: S / M (stainless steel, superalloys) Tolerance class: M Series: Tiger‑tec Silver FAQ What materials is this insert suitable for? The CCMT09T304‑MW4 WSM20S insert is designed for stainless steel and heat‑resistant superalloys (material groups S and M), offering thermal stability and controlled chip formation for such alloys. How does the MW4 chipbreaker affect machining? The MW4 chipbreaker on this Walter Tools insert shapes chips for reliable evacuation, which improves process security and reduces the likelihood of built‑up edge during turning operations. What is the benefit of the 0.4 mm corner radius? A 0.4 mm corner radius provides a compromise between edge strength and surface finish, helping to maintain a durable cutting edge while delivering good workpiece quality in finishing passes. Is this insert suitable for both roughing and finishing? Yes; the geometry and coating enable productive roughing with appropriate cutting parameters and stable finishing with improved surface integrity on stainless steel. Which series and coating technology is used on the insert? The insert belongs to the Tiger‑tec Silver series and uses the associated coated carbide technology, optimised for thermal resistance and edge stability. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarked names and designations are the property of their respective owners. Brand names are mentioned for clarification of application and compatibility. The offered article is original and brand‑new from the manufacturer. Walter Tools is a brand of the Walter AG, part of the Sandvik Group.
CCMT09T304-RK4 WKK10S WKK10S Wendeplatten - Walter Tools
Combining the Tiger·tec Silver coating with the RK4 chipbreaker and a 7° clearance angle delivers reliable chip control and extended tool life for cast iron machining; order directly via Metav Werkzeuge or contact our technical team for application advice. CCMT09T304-RK4 WKK10S indexable insert — RK4 chipbreaker for cast iron (Walter Tools) A CCMT09T304-RK4 WKK10S insert engineered for productive cast iron turning and boring, offering Tiger·tec Silver performance in a rhombic 80° geometry. Tiger·tec Silver coated carbide Optimised RK4 chipbreaker Designed for cast iron machining Rhombic 80° insert geometry Stable chip control for higher process efficiency The combination of the RK4 chipbreaker and the Tiger·tec Silver coating is designed to control the short, breaking chips typical of cast iron. The chipformer geometry reduces interruptions and decreases tool changes, which in turn supports higher productivity in serial production. For operators with limited metrology background: a chipbreaker channels and fractures chips reliably, preventing blockages and improving cycle consistency while also protecting the cutting edge from irregular loading. Geometry that improves surface finish and insert life The rhombic 80° geometry together with a 7° clearance and a 0.4 mm corner radius offers a balanced compromise between cutting strength and accessibility in tight turning grooves. The modest corner radius supports a better surface finish on interrupted surfaces and extends the effective life of the cutting edge under abrasive conditions typical for cast iron. The tolerance class M ensures consistent seat fit and repeatable positioning in standard toolholders, which reduces rework and fixture adjustments on the shop floor. Versatile application across turning and boring operations Classified for cast iron workpieces, the grade WKK10S is a coated carbide solution optimised for abrasive wear and frequent short-chip formation. The insert is suitable for both turning and boring set-ups where reliable chip flow and stable cutting forces are required. In production environments the insert’s design supports straightforward integration into common toolholders and boring heads used in machining centres and lathes, allowing shops to standardise tooling across similar cast iron operations. Practical handling and performance guidance For best results, pair the insert with tool geometries and feeds matched to cast iron characteristics: medium cutting speeds and steady feed rates produce the intended chip shape and promote consistent wear. The Tiger·tec Silver technology improves thermal resistance and edge stability, which lowers tooling costs per component in longer runs. If application parameters require fine-tuning, consult the technical documentation or our specialists for recommended speed and feed windows tailored to specific cast iron grades. Contact Metav Werkzeuge for application-specific recommendations and secure delivery of Walter Tools inserts — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Details SKU: CCMT09T304-RK4-WKK10S-WALTER Article designation: CCMT09T304-RK4 WKK10S Manufacturer: Walter Tools Product type: drilling/boring and turning indexable insert Series: Tiger·tec Silver Core Data Clearance angle: 7° Corner radius: 0.4 mm Insert shape: Rhombic 80° Insert size: 09 Thickness: T3 Tolerance class: M Special features Grade: WKK10S (coated carbide) Chipbreaker: RK4 Optimised for: cast iron machining Suitable operations: turning and boring FAQ Which workpiece materials is this grade suitable for? The WKK10S grade and the CCMT09T304-RK4 WKK10S insert are optimised for cast iron; the coating and chipformer address abrasive wear and short-chip behaviour typical of these materials. How does the chipbreaker affect machining of cast iron? The RK4 chipbreaker on the CCMT09T304-RK4 WKK10S insert directs and fractures chips efficiently, reducing the risk of entanglement and improving process stability in cast iron turning and boring. What insert geometry and edge preparation does it have? This insert features a rhombic 80° shape with a 0.4 mm corner radius and a 7° clearance, balancing edge strength and accessibility for interrupted cuts. Is the insert suitable for both turning and boring setups? Yes, the CCMT09T304-RK4 WKK10S is specified for drilling/boring and turning operations and fits common toolholders used in lathes and machining centres. What does the Tiger·tec Silver designation mean for performance? Tiger·tec Silver denotes Walter Tools’ coating and substrate technology that enhances thermal resistance and edge stability, helping to extend tool life under abrasive cast iron conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
CCMT09T304-RK4 WKK20S RK4 Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability, cast iron-optimised grade and a consistent chip control that reduces rework and extends tool life. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. CCMT09T304-RK4 WKK20S indexable turning insert – Tiger-tec Silver, RK4 chipbreaker by Walter Tools The CCMT09T304-RK4 WKK20S is a coated carbide turning insert designed for productive cast iron machining with stable chip formation and long tool life Optimised for cast iron machining Tiger-tec Silver coated carbide grade RK4 chipbreaker for short, controlled chips Rhombus 80° geometry for versatile turning Consistent results on abrasive cast iron components The Tiger-tec Silver coating combined with the WKK20S grade is formulated to resist the abrasive wear typical of cast iron. This results in a clearly extended tool life and a more predictable wear pattern, which benefits batch production and tight-tolerance runs. The RK4 chipbreaker is tailored for the short, brittle chips produced by grey and nodular cast iron, reducing the risk of chip entanglement and improving surface integrity. In practical terms, these characteristics mean fewer interruptions for tool changes and a more stable process window, which supports higher throughput and consistent surface finish on critical diameters. Geometry and edge specification for accurate finishing The Rhombus 80° insert form and the 7° clearance angle combine to offer a reliable cutting geometry for general turning and finishing operations. The small 0.4 mm corner radius supports fine edge finishes and modest approach depths while preserving edge strength for repeatable results. With a compact T3 thickness and the established CCMT09T304-RK4 outline, the insert suits standard tool holders and clamping systems used in lathes and turning centres, enabling straightforward retrofit into existing tool inventories. The designation reflects a balance between robustness and the ability to achieve close tolerances on components where form and surface quality are decisive. Operational advantages: process safety and inventory efficiency Specifying a grade optimised for cast iron machining reduces scrap and rework. The WKK20S carbide offers a universal toughness level that copes with fluctuating cast iron microstructures while the coating minimises adhesion and flank wear. The tolerance class M ensures consistent dimensions between indexable edges, aiding rapid re-indexing and predictable cycle times. For purchasing and stock management, the standardised form factor and compatibility with widely used holders simplify logistics and reduce downtime. Overall, the insert supports a cost-effective machining strategy through lower tooling consumption per part and a reliable, repeatable cutting performance. Select the Walter Tools Tiger-tec Silver grade for demanding cast iron turning — contact Metav Werkzeuge for tailored recommendations and immediate availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: CCMT09T304-RK4-WKK20S-WALTER Designation: CCMT09T304-RK4 WKK20S Series: Tiger-tec Silver Grade: WKK20S Manufacturer: Walter Tools Facts Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Corner radius: 0.4 mm Free angle: 7° Chipbreaker: RK4 Tolerance class: M Special features Coated carbide grade optimised for cast iron Stable chip formation for short, breaking chips Productive wear resistance and consistent edge life Suitable for turning and boring applications on cast iron FAQ What materials is this insert suitable for? The CCMT09T304-RK4 WKK20S insert is optimised for machining cast iron; the WKK20S grade and chipbreaker geometry are tuned to abrasive, short-chip behaviour typical of these materials. How does the RK4 chipbreaker improve machining? The RK4 chipbreaker controls chip form for short, easily managed chips in cast iron turning, reducing chip-related interruptions and improving surface quality with consistent cutting forces. Can this insert be used for finishing operations? Yes, the small 0.4 mm corner radius and Rhombus 80° geometry make the insert suitable for light finishing cuts where surface integrity and dimensional accuracy are required. Is the CCMT09T304-RK4 compatible with standard tool holders? The CCMT-shaped insert and standard size designation mean it fits most conventional tool holders for indexable turning, allowing easy replacement and inventory harmonisation. What process benefits does the Tiger-tec Silver coating provide? The Tiger-tec Silver coating enhances wear resistance and reduces built-up edge tendencies on cast iron, delivering longer tool life and more predictable performance in production environments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools: The Walter AG (brand: Walter Tools) is part of the Sandvik Group and is a leading manufacturer of precision metalworking tools. Protected trademarks and product names are the property of their respective owners. The mentioned brand names are used for explanation only. There is no affiliation between Metav Werkzeuge and the named manufacturers. The offered item is original, factory-new goods of the manufacturer.
CCMT09T304-RM4 WMP20G RM4 Wendeplatten - Walter Tools
Combining the Tiger‑tec Gold grade with a robust RM4 chipbreaker and a 0.4 mm corner radius ensures secure chip formation and consistent edge life in demanding stainless steel turning. Order the CCMT09T304-RM4 WMP20G directly via Metav Werkzeuge or ask the Metav consultants for material‑specific recommendations. CCMT09T304-RM4 · CCMT09T304-RM20G WMP20G — Rhombic 80° turning insert for stainless steel, Tiger‑tec Gold, Walter Tools A CCMT09T304-RM4 WMP20G is a rhombic 80° turning insert developed for medium to robust machining conditions on stainless steel, providing stable cutting performance with Tiger‑tec Gold coating. Tiger‑tec Gold coated carbide grade WMP20G Optimised for stainless steel machining Rhombic 80° shape, 0.4 mm corner radius Greater throughput through coated‑grade performance The Tiger‑tec Gold coated carbide formulation combines wear resistance with thermal stability to maintain a stable cutting edge under the challenging conditions of machining stainless steel. This results in more predictable tool life and fewer interruptions for index changes, which improves overall shop throughput. The combination of the WMP20G grade and the RM4 chipbreaker promotes secure chip control, reducing the risk of built‑up edge that typically degrades surface finish and cycle time. Geometry that improves surface quality and process reliability The rhombic 80° geometry paired with a 0.4 mm corner radius and a 7° clearance provides a balanced contact area for turning operations. A defined corner radius supports smoother transitions and better load distribution on the cutting edge, which translates to improved surface finish and reduced micro‑chipping. The RM4 chipbreaker shapes chips for stable evacuation, lowering the chance of entanglement and easing handling. For those unfamiliar, the corner radius is the small rounded edge at the insert tip that influences strength and finish: larger radii increase strength but may raise cutting forces, while the 0.4 mm radius here offers a pragmatic compromise for stainless steels. Practical selection and application advice for shop environments The insert is supplied in the CCMT09T304 format with a T3 thickness and size designation 09, making it compatible with standard turning toolholders that accept rhombic 80° indexable inserts. Its specification for the ISO M group confirms suitability for stainless steel grades that generate toughness and heat; the coating reduces adhesion and extends edge life. When integrating this insert into production, select cutting parameters that mitigate heat build‑up—moderate cutting speeds and steady feed—so the coated grade can deliver its full potential. Walter Tools’ emphasis on process reliability supports consistent results across batch and single‑piece production. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger‑tec Gold inserts and to check stock availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CCMT09T304-RM4-WMP20G-WALTER Designation: CCMT09T304-RM4 ISO designation: CCMT09T304-RM4 WMP20G Grade: WMP20G Series: Tiger‑tec Gold Manufacturer: Walter Tools Facts Shape: Rhombus 80° Corner radius: 0.4 mm Clearance angle: 7° Insert size: 09 Thickness: T3 Chipbreaker: RM4 Special features Coated carbide Suited for stainless steel (ISO M) Designed for medium to robust cutting conditions Rhombic 80° insert geometry Walter Tools brand FAQ What materials is this insert best suited for? The CCMT09T304-RM4 WMP20G is optimised for stainless steel (ISO M), with the Tiger‑tec Gold coating and RM4 chipbreaker specifically designed to manage the toughness and heat sensitivity of these alloys. How does the RM4 chipbreaker affect machining? The RM4 chipbreaker on this Walter Tools insert shapes chips for reliable evacuation and reduces the likelihood of built‑up edge, improving surface finish and enabling more stable machining cycles. Can the insert be used for finishing operations? Yes, the combination of a 0.4 mm corner radius and controlled geometry permits good surface quality; however, finishing parameters should be selected with lower feeds and appropriate speeds for best results. Which toolholder types accept the CCMT09T304 format? Standard turning toolholders designed for rhombic 80° indexable inserts with CCMT format are compatible; ensure the holder supports the 09 size and T3 thickness for correct seating. What benefit does the Tiger‑tec Gold series provide? Tiger‑tec Gold enhances wear resistance and thermal stability, offering extended edge life and consistent cutting performance when machining demanding materials such as stainless steel. The Walter AG (brand: Walter Tools) is part of the Sandvik Group. Protected trademarks and trade names are mentioned for explanatory purposes only. There is no affiliation implied between our company and the mentioned brands. The listed article is an original, factory‑new product of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com