CCMT09T308-FP4 WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, the FP4 chipbreaker and a rhombic 80° geometry to achieve stable chip control and extended tool life in steel turning; order directly via Metav Werkzeuge or consult our technical team for application support. CCMT09T308-FP4 WPP10G – Turning insert, Tiger‑tec Gold, for steel | Walter Tools The CCMT09T308-FP4 WPP10G is a coated turning insert designed for reliable steel machining, featuring a rhombic 80° shape and a robust chipbreaker for consistent metal removal. Tiger‑tec Gold coated carbide Optimised for steel machining Rhombic 80° geometry for stability Corner radius 0.8 mm, 7° clearance Boosted process reliability with advanced coating and chip control The combination of Tiger‑tec Gold and coated carbide technology delivers notably improved wear resistance and thermal protection during heavy-duty turning of steel. The FP4 chipbreaker supports controlled chip formation, reducing interruptions and tool‑change frequency; this converts directly into fewer downtimes and more predictable batch throughput. The chemistry and layering of the grade are tuned for the heat and chip characteristics typical of ISO P materials, helping to maintain cutting edge integrity under continuous operation. Geometry that enhances stability and surface quality A rhombic 80° geometry provides a stable cutting orientation and improved support for the cutting edge, which benefits both roughing and medium finishing passes. The corner radius 0.8 mm increases edge robustness for interrupted cuts, while the 7° clearance helps to avoid flank rubbing and heat build‑up. These geometric choices combine to give a balance between tool life and achievable surface finish, making the insert suitable for a range of turning strategies where consistent part quality is required. Predictable performance and broad steel coverage The WPP10G grade in the Tiger‑tec Gold series is crafted for broad applicability across unalloyed and alloyed steels, offering a mix of wear resistance and toughness that supports repeatable results. The CCMT09T308-FP4 WPP10G insert is designed to deliver consistent tool life and stable chip control, which simplifies process parameter selection and shortens setup times. For shops aiming to raise productivity while keeping machining parameters reliable, this insert delivers a convincing balance of economy and performance. For machining recommendations or availability of the Walter Tools CCMT09T308-FP4 WPP10G, contact Metav Werkzeuge for tailored advice and fast delivery: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: CCMT09T308-FP4-WPP10G-WALTER Designation: CCMT09T308-FP4 ISO designation: CCMT09T308-FP4 WPP10G Grade: WPP10G Series: Tiger‑tec Gold Manufacturer: Walter Tools Core specifications Geometry: Rhombus 80° Corner radius: 0.8 mm Clearance angle: 7° Insert size: 09 Thickness: T3 Tolerance class: M Chipbreaker: FP4 Materials & features Coating: Tiger‑tec Gold (coated carbide) Suitable for: steel (ISO P) Execution: T Plate form: CCMT (rhombic) Engineered for stable chip formation and reliable wear behaviour FAQ Which materials is this insert suitable for? The CCMT09T308-FP4 WPP10G is formulated for machining steel (ISO P), including unalloyed and alloyed grades commonly encountered in general turning. How does the Tiger‑tec Gold coating benefit machining? The Tiger‑tec Gold coating on the WPP10G grade improves thermal resistance and reduces abrasive wear on the cutting edge, which helps the insert maintain performance during prolonged turning cycles. What is the role of the FP4 chipbreaker? The FP4 chipbreaker promotes controlled chip formation and evacuation, reducing the risk of chip entanglement and supporting uninterrupted production when using the CCMT09T308-FP4 WPP10G. Is this insert suitable for interrupted cuts or heavy depths of cut? With a corner radius 0.8 mm and rhombic 80° geometry, the insert provides a robust cutting edge that tolerates intermittent engagement and offers improved stability under heavier loads. Can the CCMT09T308-FP4 WPP10G be used for finishing operations? Yes; by selecting appropriate feeds and speeds the insert can achieve good surface quality, thanks to the combined benefits of rhombic geometry and the Tiger‑tec Gold coating. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, brand‑new product of the manufacturer Walter Tools.
CCMT09T308-FP4 WPP20G Tiger-tec Gold Wendeplatten - Walter Tools
Take advantage of a coated‑carbide grade engineered for steel to increase uptime and cutting stability; the WPP20G composition with Tiger‑tec Gold technology delivers long tool life, while the FP4 chipbreaker and Rhombic 80° geometry secure predictable chip formation and consistent surface quality. Order the insert directly via Metav Werkzeuge or consult our technical team for process integration. CCMT09T308-FP4 WPP20G – Turning and boring indexable insert, Tiger‑tec Gold, Walter Tools A versatile indexable insert, CCMT09T308-FP4 WPP20G is a rhombic 80° turning and boring plate optimised for machining steel under ISO P conditions. Tiger‑tec Gold coating for extended tool life Engineered for ISO P (steel) machining FP4 chipbreaker for stable chip control Rhombic 80° form with 7° clearance angle Proven performance for steel turning The combination of the WPP20G grade and Tiger‑tec Gold coating provides a balanced wear resistance and toughness that is particularly effective when machining a wide range of steels. As a coated carbide insert designed for ISO P applications, it reduces the risk of thermal wear and flank wear in continuous and interrupted cuts, which supports higher productivity and fewer tool changes. The robust grade selection affords a reliable service life while preserving dimensional accuracy during extended production runs. Consistent chip control and surface quality The FP4 chipbreaker is engineered to produce predictable chip shapes during both roughing and finishing, reducing the likelihood of built‑up edge and improving chip evacuation in bore and turning operations. With a 0.8 mm corner radius and a 7° clearance angle, the insert helps secure a stable cutting engagement and enhanced surface finish on machined components. These geometric features translate into more consistent part quality and reduced rework rates in serial production. Robust geometry for process reliability The Rhombic 80° geometry and size 09 format provide a favourable compromise between cutting strength and accessibility in shoulder and profiling operations. The T3 thickness and tolerance class M ensure dimensional repeatability when indexing inserts and mounting in standard toolholders, supporting reproducible set‑ups across multiple machines. This stability helps to maintain cycle times and lower overall machining costs by limiting unexpected tool failures. Practical integration and application scope Rated primarily for steel (ISO P), this insert suits a broad mix of operations where a universal performance grade is required. The CCMT09T308-FP4 WPP20G insert integrates into common turning and boring toolholders in industrial workshops and is particularly effective where stable chip control and predictable wear behaviour are priorities. If additional process data or application‑specific recommendations are needed, technical consultation is available to match cutting parameters and clamping solutions to the machining task. Contact Metav Werkzeuge for tailored cutting data, availability and advice on integrating the CCMT09T308-FP4 WPP20G insert into production processes Technical Data Article number: CCMT09T308-FP4-WPP20G-WALTER Designation: CCMT09T308-FP4 ISO designation: CCMT09T308-FP4 WPP20G Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WPP20G Chipbreaker: FP4 Shape: Rhombic 80° Size: 09 Thickness: T3 Corner radius: 0.8 mm Clearance angle: 7° Tolerance class: M Execution: T Material group: P (steel) Facts Corner radius: 0.8 mm Clearance angle: 7° Size indicator: 09 Thickness code: T3 Tolerance: M Special features Coated carbide grade WPP20G Tiger‑tec Gold coating technology FP4 chipbreaker for predictable chips Geometry: Rhombic 80° Suitable for ISO P (steel) FAQ What materials is this insert intended for? The CCMT09T308-FP4 WPP20G insert is specified for ISO P applications and is designed primarily for machining steel. How does the Tiger‑tec Gold technology benefit production? The Tiger‑tec Gold coating on the WPP20G grade improves wear resistance and heat management, extending tool life and enabling more consistent results during prolonged turning or boring operations. Is the FP4 chipbreaker suitable for both roughing and finishing? The FP4 chipbreaker offers controlled chip formation that performs well across a range of feeds, supporting both robust roughing cuts and finer finishing passes when process parameters are adjusted accordingly. What does the 0.8 mm corner radius affect on the component surface? A 0.8 mm corner radius contributes to improved surface integrity and edge strength; it helps reduce cutting forces spikes and supports better surface finish compared with very small radii. Can this insert be indexed in standard CCMT toolholders? Yes, the CCMT09T308-FP4 format matches standard CCMT toolholders; the specified tolerance class M and T3 thickness ensure consistent fit and repeatability. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product from Walter Tools.
CCMT09T308-FP6 WPP10G FP6 Wendeplatten - Walter Tools
The high-wear Tiger·tec Gold grade and the optimised FP6 chipbreaker deliver reliable productivity and consistent surface finish; order directly via Metav Werkzeuge or consult our specialists for application advice. CCMT09T308-FP6 WPP10G — Turning insert, Tiger·tec Gold grade, Walter Tools A CCMT09T308-FP6 WPP10G indexable turning insert for steel machining, engineered for stable chip formation and long tool life Tiger·tec Gold coating for long tool life Optimised FP6 chipbreaker for stable chips 80° rhombic shape, 0.8 mm nose radius High-performance grade for steel turning and durability The WPP10G grade, part of the Tiger·tec Gold series, is a coated carbide designed specifically for ISO P (steel) applications. Its coating technology improves thermal stability and reduces flank wear, which translates into longer intervals between tool changes and predictable tool life in both roughing and finishing operations. As a result, process stability is enhanced and production throughput can increase without compromising surface integrity. The technical design focuses on managing the heat and chip formation typical of steel machining, making this insert a reliable option for general to demanding turning tasks. Geometry and chip control for consistent machining performance The 80° rhombic contour combined with a 7° clearance angle and an FP6 chipbreaker yields controlled chip formation and effective evacuation across a range of cutting parameters. The 0.8 mm nose radius supports good surface finish while still allowing robust cutting conditions where required. These geometric choices reduce the likelihood of built-up edge and improve surface consistency, especially on interrupted cuts or variable feed rates. The medium tolerance class M ensures interchangeability and repeatable mounting accuracy in standard toolholders, supporting efficient toolset management on the shop floor. Applications, handling and process guidance for reliable results This insert is intended primarily for machining steel (ISO P) and covers a broad span from wear-resistant to tougher steel grades. The plate thickness T3 and size 09 make it suitable for common toolholder families used in turning and light boring operations. When integrated into a stable holder and paired with appropriate cutting parameters, this indexable solution promotes reduced downtime and easier tool changeover routines. For first-time setups, start with conservative cutting values and monitor wear progression to dial in optimised feeds and speeds for each batch, benefiting from the grade’s balanced toughness and wear resistance. For high-productivity steel turning with proven Tiger·tec Gold performance, contact Metav Werkzeuge for application recommendations and stock information Technical data Article number: CCMT09T308-FP6-WPP10G-WALTER SKU: CCMT09T308-FP6-WPP10G-WALTER Designation: CCMT09T308-FP6 WPP10G Facts Clearance angle: 7° Corner radius: 0.8 mm Plate size: 09 Thickness: T3 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP10G (coated carbide) Chipbreaker: FP6 Shape: Rhombic 80° Application group: ISO P (steel) Execution: T Manufacturer brand: Walter Tools FAQ What materials is this insert designed for? The CCMT09T308-FP6 WPP10G insert is formulated for ISO P materials, primarily steel, and is optimised for the typical heat and chip formation encountered when turning steel. How does the FP6 chipbreaker affect machining? The FP6 chipbreaker on this Walter Tools turning insert promotes short, controllable chips and reliable evacuation, improving process stability and surface finish during steel turning. Can this insert be used for finishing as well as roughing? Yes, the combination of the 0.8 mm nose radius and the Tiger·tec Gold grade on this turning insert supports both finishing and more aggressive cuts, depending on chosen cutting parameters. What does tolerance class M mean for toolholders? Tolerance class M indicates a medium manufacturing tolerance, ensuring good repeatability and interchangeability in standard indexable insert toolholders when using this Walter Tools insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are mentioned for explanatory purposes only and indicate no affiliation between our company and the named brands. The offered item is an original, factory-new product of Walter Tools.
CCMT09T308-FP6 WPP20G WPP20G Wendeplatten - Walter Tools
Maximise turning performance with the Tiger·tec Gold WPP20G grade and the FP6 chipbreaker: precise chip control and extended tool life support efficient, repeatable steel machining — order directly via Metav Werkzeuge or consult the technical team for application advice. CCMT09T308-FP6 WPP20G — Turning insert, Tiger·tec Gold, FP6, Walter Tools CCMT09T308-FP6 WPP20G is a rhombic 80° indexable turning insert formulated for steel machining, combining a Tiger·tec Gold coating with a FP6 chipbreaker to deliver controlled chip formation and consistent surface finish. Tiger·tec Gold coated carbide grade WPP20G Geometry FP6 chipbreaker for stable chips Rhombic 80° shape, 0.8 mm corner radius Designed for steel (ISO P), free angle 7° Stable performance from a coated grade The WPP20G grade, part of the Tiger·tec Gold series, is a coated carbide solution optimised for the thermal and mechanical demands of turning steel (ISO P). Its coating technology improves wear resistance and reduces flank wear under typical steel cutting temperatures, which contributes to a longer tool life and fewer insert changes. For production environments that prioritise throughput and repeatability, the combination of this grade with a stable substrate ensures a measurable reduction in downtime and predictable replacement cycles. Precision geometry that controls chips and finish A well‑defined chipformer and rake geometry make the difference between frequent interruptions and uninterrupted cutting. The FP6 chipbreaker is engineered for consistent chip segmentation in common steel grades, reducing the risk of entangling long chips and improving process stability. The 0.8 mm corner radius and rhombic 80° shape support accurate profile reproduction and contribute to a superior surface finish on turned components, particularly where dimensional consistency is required across batches. Practical gains for machining productivity Using this insert family can lead to tangible production benefits: reduced cycle variability, stable cutting forces and improved edge life. The moderate 7° free angle supports finishing to medium depths of cut while maintaining edge strength, so operators experience a balance between cutting security and achievable surface quality. Explained plainly, the insert’s features translate into fewer interruptions for tool change, more consistent part quality and a better cost‑per‑component figure in serial turning operations. Handling and application guidance for the workshop The insert is supplied in the CCMT format and a T‑type execution, making it compatible with standard turning toolholders designed for rhombic 80° inserts. The series: Tiger·tec Gold and grade: WPP20G indicate suitability for a broad range of steel machining tasks, with reliable chip control in mixed material batches. For workshop planning, the insert’s designation and geometry simplify tool selection and inventory management, since the coding corresponds to widely used ISO insert standards and toolholder interfaces. For demanding steel turning applications, consider Walter Tools’ Tiger·tec Gold WPP20G inserts via Metav Werkzeuge for consistent chip control and extended edge life — contact Metav Werkzeuge for application-specific advice and supply options: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: CCMT09T308-FP6-WPP20G-WALTER Label: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCMT09T308-FP6 WPP20G Walter Tools ISO designation: CCMT09T308-FP6 WPP20G Core specifications Corner radius: 0.8 mm Free angle: 7° Plate size: 09 Plate thickness: T3 Tolerance class: M Materials & features Grade: WPP20G Series: Tiger·tec Gold Chipbreaker: FP6 Shape: Rhombus 80° Execution: T Intended application: Steel (ISO P) FAQ What material range is this insert intended for? This insert is specified for steel machining (ISO P) and the WPP20G grade of the Tiger·tec Gold series is tuned for the thermal and chip‑forming behaviour typical of unalloyed and alloyed steels. How does the FP6 chipbreaker affect machining? The FP6 chipbreaker promotes regular chip segmentation and stable evacuation when cutting steel, improving process reliability and reducing the likelihood of chip interference in turning operations. Which toolholders are compatible with this insert format? The CCMT form factor and rhombic 80° geometry are compatible with standard turning holders designed for 80° rhombic inserts; holders accepting CCMT‑type inserts will suit this product. Does the 0.8 mm corner radius suit finishing operations? A 0.8 mm corner radius provides a compromise between edge strength and surface finish, making it suitable for finishing and light semi‑finishing passes where dimensional control and surface integrity matter. Is this an original Walter Tools product? The article is an original factory‑new product from Walter Tools, presented under the manufacturer’s specified grade and series. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T308-FW4 WKP01G WKP01G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, the FW4 chipbreaker for reliable chip control and compatibility with steel and cast iron to maintain productive turning cycles; order via Metav Werkzeuge or consult the specialists for application advice. CCMT09T308-FW4 WKP01G indexable turning insert – Rhombic 80°, 0.8 mm nose radius | Walter Tools The CCMT09T308-FW4 WKP01G is an indexable turning insert crafted for general turning operations on steel and cast iron, offering a balance of wear resistance and consistent chip control. Tiger·tec Gold coating for enhanced wear resistance Coated carbide grade WKP01G for steel and cast iron Rhombic 80° form with 0.8 mm nose radius FW4 chipbreaker for stable chip control High productivity through coated-grade performance The combination of the WKP01G coated carbide grade and the Tiger·tec Gold coating is engineered to extend tool life under typical turning loads. This insert reduces unplanned tool changes by improving edge stability and abrasion resistance during continuous operation on steel and cast iron, which means fewer stoppages and a steadier production output. The result is measurable efficiency: longer tool life and more predictable change intervals contribute to a lower effective cost per part without sacrificing surface quality. Reliable chip control and geometry that aids process stability The FW4 chipbreaker is designed to form controllable chips in a wide range of turning passes, lowering the risk of entanglement in both roughing and light finishing cuts. The Rhombic 80° geometry, combined with a 0.8 mm nose radius, provides a favourable balance between cutting edge strength and surface finish capability. Together, these features support stable cutting forces and consistent part tolerances, particularly in serial production contexts where repeatability is essential. Practical application guidance and machining scope This insert is specified for materials classified under ISO groups P (steel) and K (cast iron), making it suitable for unalloyed and alloyed steels as well as abrasive cast materials where controlled chip breakage is needed. The 7° relief angle supports positive cutting engagement, while the tolerance class M ensures consistent dimensional quality across batches. For best results, pair the insert with suitable holder geometry and set cutting parameters according to workpiece machinability; specialist advice is available from Metav Werkzeuge for optimising parameters for specific machines and workpiece materials. For tailored machining recommendations for this Walter Tools insert or to confirm stock availability, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or +49 2822 7131930—our team will advise on the ideal grade and cutting data for the intended application. Technical data Article number: CCMT09T308-FW4-WKP01G-WALTER Designation: CCMT09T308-FW4 WKP01G Type: Indexable turning insert Series: Tiger·tec Gold Manufacturer: Walter Tools Facts Corner radius: 0.8 mm Relief angle: 7° Insert form: Rhombic 80° Insert size: 09 Thickness: T3 Tolerance class: M Special features Grade WKP01G – coated carbide Chipbreaker: FW4 Material suitability: Steel (P) and Cast iron (K) Coating: Tiger·tec Gold FAQ Which materials can be machined with this insert? The CCMT09T308-FW4 WKP01G is specified for ISO groups P and K, meaning it is suitable for a range of steel grades and cast iron applications. What benefit does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WKP01G grade improves wear resistance and edge life, contributing to longer service intervals and more stable machining on abrasive materials. Is the FW4 chipbreaker suitable for finishing passes? The FW4 chipbreaker offers stable chip formation across roughing and light finishing; for high-finishing demands, verify required surface finish and adjust feed and depth of cut accordingly. Does this insert suit stainless steel machining? Stainless steel is not listed among the specified ISO material groups for this grade; the CCMT09T308-FW4 WKP01G is optimised for steel and cast iron, so alternative grades should be considered for sustained stainless steel machining. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation purposes only. There is no affiliation between our company and the named brands. The offered item is an original, brand-new product from the manufacturer.
CCMT09T308-FW4 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating, the WPP10G grade and a precise 7° clearance angle for consistent, efficient steel turning; reliable chip control and a 0.8 mm corner radius support high process stability. Order the insert directly via Metav Werkzeuge or ask our consultants if needed. CCMT09T308-FW4 WPP10G – Turning insert for steel (Rhombic 80°) by Walter Tools A coated CCMT09T308-FW4 WPP10G turning insert engineered for stable medium-duty steel machining, offering consistent wear behaviour and dependable surface quality in production environments Tiger·tec Gold coating for long life Optimised for steel (ISO P) chipforming Rhombic 80° geometry, 0.8 mm corner radius 7° clearance angle for secure cutting Consistent cutting performance for production machining The insert delivers a balance of productivity and predictability: the combination of a coated carbide grade and a defined cutting geometry provides stable cutting forces and repeatable component quality. For series production or frequent tool changes, the consistency of the cutting edge reduces process variations and downtime. The rhombic geometry supports turning operations where access and clearance are critical, while the nominal corner radius improves tool life without compromising dimensional control. Coating and grade that extend tool life under heat The Tiger·tec Gold technology and WPP10G grade create a wear‑resistant surface with good heat resistance and adhesion, which translates into longer intervals between insert changes. The coated hardmetal construction reduces crater wear and supports higher cutting parameters compared with uncoated grades, enabling improved economy on steel workpieces. Explained simply: the coating acts as a thermal and chemical shield, slowing wear mechanisms and maintaining a sharper cutting edge for longer. Controlled chips and secure cutting geometry Chip control is essential for safe machining and consistent finishes; the FW4 chipbreaker is designed to produce predictable chip shapes when machining steel (ISO P), minimising entanglement and supporting automated workflows. The Rhombic 80° outline and 0.8 mm corner radius contribute to an even contact pattern and reliable edge strength, while the 7° clearance angle reduces rubbing and heat build‑up at the flank. Together these features improve surface finish and reduce the risk of built‑up edge. Practical application guidance for workshop and production This insert is tailored to steel turning tasks where a mix of wear resistance and toughness is required. With a nominal thickness of T3 and tolerance class M, it suits standard toolholders that accept ISO indexable inserts in the CCMT size family. The grade supports typical steel machining heat and chip formation patterns; for best results pair the insert with stable toolholding and adapt cutting data to part rigidity and machine capability. For specialists and general workshop users alike, the result is a dependable insert for everyday production. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger·tec Gold inserts and to discuss availability or technical matching to specific turning operations Technical Data SKU: CCMT09T308-FW4-WPP10G-WALTER Article designation: CCMT09T308-FW4 Full designation: CCMT09T308-FW4 WPP10G Manufacturer: Walter Tools Dimensions & key figures Clearance angle: 7° Corner radius: 0.8 mm Insert size: 09 Plate thickness: T3 Tolerance class: M Design & features Coating: Tiger·tec Gold Grade: WPP10G Shape: Rhombic 80° Chipbreaker: FW4 Application group: Steel (ISO P) Series: Tiger‑tec Gold FAQ What materials is this insert suitable for? The CCMT09T308-FW4 WPP10G insert from Walter Tools is specified for steel machining (ISO P) and is formulated to handle the typical heat and chip formation of unalloyed and alloyed steels. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating on the WPP10G grade improves wear resistance and thermal stability, which in turn extends tool life and supports higher cutting parameters in continuous production runs. What is the purpose of the FW4 chipbreaker? The FW4 chipbreaker is engineered to produce consistent, manageable chips when machining steel, reducing entanglement and improving process reliability with automatic and manual chip evacuation. Which insert dimensions and tolerance class apply to this product? The insert is a CCMT09T308 geometry with a 0.8 mm corner radius, thickness T3 and tolerance class M; the SKU is CCMT09T308-FW4-WPP10G-WALTER. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned solely for explanation. There is no connection between our company and the mentioned brands. The offered item is original, brand‑new goods from the manufacturer.
CCMT09T308-FW4 WPP20G FW4 Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating and the FW4 chipbreaker for consistent chip control and extended tool life; the rhombic 80° geometry with a 0.8 mm corner radius ensures robust edge strength for demanding steel machining. Order the insert directly via Metav Werkzeuge or consult the technical team for cutting data and toolholder compatibility. CCMT09T308-FW4 WPP20G indexable turning insert, Tiger‑tec Gold, for steel – Walter Tools The CCMT09T308-FW4 WPP20G is an indexable turning insert for steel machining, featuring a Tiger‑tec Gold coated carbide grade and a rhombic 80° geometry for reliable, productive cutting. Turning insert »CCMT09T308-FW4 WPP20G« by Walter Tools Tiger‑tec Gold coated for high process security Rhombic 80° geometry with 0.8 mm radius Optimised FW4 chipbreaker for steel applications Extended tool life through advanced coating technology The coated carbide grade WPP20G, part of the Tiger‑tec Gold series, delivers improved resistance to flank and crater wear under the thermal and mechanical loads typical of machining steels. The result is a longer service life of the cutting edge and fewer insert changes, which contributes directly to higher productivity and lower tooling costs per component. The coating also supports stable cutting at elevated speeds, offering a reliable balance between wear resistance and toughness for general steel applications. Predictable chip control and stable cutting for better productivity The FW4 chipbreaker, combined with the rhombic 80° format and a 7° relief angle, provides controlled chip formation and evacuation when machining ISO P materials. This geometry reduces chatter and vibration while promoting a consistent surface finish, particularly during medium-depth turning. With a 0.8 mm corner radius, the insert offers enhanced edge strength for intermittent cuts and shoulder work, improving process stability in roughing and finishing operations. Easy integration into machining processes and consistent quality Designed to fit standard CCMT toolholders, the insert’s T3 thickness and tolerance class M ensure reliable seating and repeatable performance in production setups. The grade is optimised for a broad range of steels under ISO P, making it a universal choice for batch production and job-shop environments where material mix and flexibility matter. For tailored cutting parameters and to maximise component quality, technical consultation is available via Metav Werkzeuge. Consult Metav Werkzeuge for tailored cutting data and quick supply of Walter Tools Tiger‑tec Gold inserts to match specific machining requirements Technical data Article number: CCMT09T308-FW4-WPP20G-WALTER Label: Drehwendeschneidplatte CCMT09T308-FW4 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte / indexable turning insert Grade: WPP20G Series: Tiger‑tec Gold Facts Free angle: 7° Corner radius: 0.8 mm Plate shape: Rhombus 80° Size: 09 Thickness: T3 Tolerance class: M Material code: P Special features Coating: Tiger‑tec Gold Chipbreaker: FW4 Coated carbide grade: WPP20G Suitable for: Steel (ISO P) Base geometry: CCMT09T308-FW4 FAQ What materials is this insert suitable for? The CCMT09T308-FW4 WPP20G insert by Walter Tools is designed primarily for machining steels in the ISO P group. How does the Tiger‑tec Gold coating affect performance? The Tiger‑tec Gold coating on the WPP20G grade increases wear resistance and enables stable cutting performance at higher speeds, improving insert life and process reliability. Which chipbreaker is fitted and what benefit does it provide? The insert features the FW4 chipbreaker, which promotes controlled chip formation and evacuation during turning of steel, reducing the risk of built-up edge and improving surface finish. Is this insert compatible with standard CCMT toolholders? Yes, the CCMT09T308-FW4 geometry and T3 thickness are compatible with standard CCMT toolholders, ensuring straightforward integration into existing tool systems. Trademarks and trade names are the property of their respective owners. Brand names are used for explanatory purposes only; there is no connection between our company and the named brands. The offered item is original, factory‑new merchandise from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
CCMT09T308-FW4 WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance and stable chip control for consistent productivity in demanding turning operations; the WSM10S coating and FW4 chipbreaker deliver reproducible cutting results and extended edge life. Order the insert directly via Metav Werkzeuge or consult our technical team for application support. CCMT09T308-FW4 WSM10S — Indexable turning insert, Rhombic 80°, for stainless steels and superalloys — Walter Tools The CCMT09T308-FW4 WSM10S is a rhombic indexable turning insert engineered for heavy-duty applications, optimised to machine stainless steels and heat‑resistant superalloys with reliable chip control. Tiger·tec Silver coating technology Suitable for stainless steels and superalloys Rhombic 80° form with 7° relief 0.8 mm corner radius, FW4 chipbreaker Consistent cutting performance in demanding materials The combination of Tiger·tec Silver and a coated carbide substrate provides the thermal and mechanical stability required when processing stainless steels and superalloys. The series and grade selection reduces the risk of built‑up edge and supports a stable cutting edge, which in turn improves surface finish and reduces unexpected downtime. Thanks to the specified relief angle and geometry, the insert maintains repeatable behaviour across batches, making process planning more predictable. Strengthened edge geometry for longer tool life A 0.8 mm corner radius increases the load capacity of the cutting edge, while the T3 thickness contributes to overall rigidity during interrupted or heavy cuts. Combined with the FW4 chipbreaker, this geometry balances edge strength and chip formation, resulting in predictable tool life and fewer insert changes. The outcome is a lower number of tool interventions and more stable cycle times on serial turning operations. Precise chip control and reliable machining The Rhombic 80° shape and FW4 chipbreaker enable consistent chip segmentation and evacuation when working with materials that tend to produce stringy or adhesive chips. That controlled chip behaviour reduces the risk of entanglement and supports safer, cleaner machining. For production environments where reproducibility matters, the insert’s design supports steady process security and contributes to overall productivity improvements. Easy selection and integration into existing setups The ISO designation and tolerance class M make the insert straightforward to specify for common toolholder systems that accept CCMT‑style inserts. With clearly defined geometry and coating characteristics, the grade simplifies tooling decisions for engineers and buyers seeking a versatile solution for tough alloys. The combination of series characteristics and chipformer design also eases interchangeability across a range of turning applications. For machining stainless steels and superalloys with improved reliability, order the Walter Tools CCMT09T308-FW4 WSM10S insert via Metav Werkzeuge or contact our consultants for tailored cutting data and process recommendations. Technical data Article number: CCMT09T308-FW4-WSM10S-WALTER Product type: Indexable turning insert Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.8 mm Insert size: 09 Plate thickness: T3 Tolerance class: M Special features Series: Tiger·tec Silver Grade: WSM10S Chipbreaker: FW4 Plate form: Rhombus 80° Material suitability: S / M (superalloys, stainless steels) FAQ Which materials can be machined with this insert? The CCMT09T308-FW4 WSM10S insert is intended for stainless steels (M) and heat‑resistant superalloys (S), offering thermal stability and controlled chip formation for these groups. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker promotes consistent chip segmentation and evacuation, reducing entanglement and improving safety and process reliability during turning of sticky or ductile materials. What is the advantage of the 0.8 mm corner radius? A 0.8 mm corner radius increases edge strength and resistance to chipping, which supports longer insert life and more stable cutting conditions in heavy or interrupted cuts. Is this insert compatible with standard CCMT toolholders? Yes, the ISO designation CCMT09T308‑FW4 aligns with common CCMT toolholder interfaces, facilitating straightforward integration into existing setups. What does the Tiger·tec Silver series provide? The Tiger·tec Silver series delivers a coated carbide solution optimised for thermal resistance and edge stability, particularly beneficial when machining demanding materials. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T308-FW4 WSM20S FW4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver heat resistance and a proven FW4 chipbreaker for steady chip control and reliable edge life; order the insert directly via Metav Werkzeuge or consult the team for cutting data and availability. CCMT09T308-FW4 WSM20S indexable turning insert — Tiger‑tec Silver, 0.8 mm corner radius (Walter Tools) The CCMT09T308-FW4 WSM20S is an indexable turning insert designed for medium to heavy-duty machining of stainless steels and heat‑resistant alloys, offering a robust balance of edge stability and thermal resistance for demanding turning tasks Tiger‑tec Silver coated grade for heat resistance Suited to stainless steels and superalloys Rhombic 80° shape for versatile turning 0.8 mm corner radius for balanced strength High productivity when machining stainless and heat‑resistant alloys The combination of the WSM20S coated carbide grade and the Tiger‑tec Silver coating addresses common challenges in machining stainless steels and superalloys: poor thermal conductivity and a tendency to form built‑up edge. As a result, the insert promotes stable chip formation and reduces unexpected edge failure, allowing a higher and more consistent metal removal rate. The specific FW4 chipbreaker helps to break and evacuate chips reliably, which is particularly relevant when processing long or stringy chips common in these materials. Predictable tool life and process security for production environments Built with a tolerance class of M and a clearance angle of 7°, this indexable insert offers predictable cutting behaviour that supports reproducible cycle times. The moderate 0.8 mm corner radius provides a compromise between edge strength and surface finish, extending time between indexings while maintaining acceptable component quality. For workshops focused on throughput and repeatability, the grade’s thermal robustness translates into fewer tool changes and more consistent batch results, which contributes directly to cost efficiency and reduced downtime. Geometry and handling tailored to versatile turning applications The rhombic 80° geometry and insert size 09 deliver versatility across external and light profiling operations; the geometry enables stable positioning in common toolholders and good access to varied turning contours. The T3 plate thickness supports secure clamping and edge support during interrupted cuts. For teams evaluating tooling options, the insert’s combination of coated carbide, chipbreaker form and geometry simplifies tooling decisions and shortens setup time while preserving quality of finish. Contact Metav Werkzeuge for tailored cutting data, batch availability and application advice on Walter Tools Tiger‑tec Silver inserts Technical Data SKU: CCMT09T308-FW4-WSM20S-WALTER Designation: CCMT09T308-FW4 WSM20S Series: Tiger‑tec Silver Manufacturer: Walter Tools Type: Indexable turning insert Core data Clearance angle: 7° Corner radius: 0.8 mm Insert size: 09 Thickness: T3 Geometry: Rhombic 80° Tolerance class: M Features Coating/grade: WSM20S (Tiger‑tec Silver coated carbide) Chipbreaker: FW4 Material applicability: Stainless steel (M), Superalloys/Titanium (S) Plate form: Rhombus 80° Series characteristics: thermal resistance, stable edge performance FAQ What materials is the CCMT09T308-FW4 WSM20S best suited for? The CCMT09T308-FW4 WSM20S (Walter Tools) is optimised for stainless steels and heat‑resistant superalloys; the WSM20S grade and Tiger‑tec Silver coating focus on thermal stability and reliable chip control. How does the FW4 chipbreaker affect performance? The FW4 chipbreaker on this insert promotes controlled chip formation and evacuation, reducing the risk of entanglement and improving surface consistency during turning of long‑chip materials. What does the 0.8 mm corner radius mean for productivity and finish? A 0.8 mm radius balances edge strength and surface finish: it increases resistance to edge chipping for productivity while still enabling an acceptable surface quality without excessive cutting forces. Is this insert suitable for interrupted cuts and roughing? Yes; the rhombic 80° geometry combined with the T3 plate thickness offers good edge support and clamping stability, making the insert appropriate for many interrupted‑cut and roughing scenarios. Can the insert be used in standard ISO toolholders? The insert’s CCMT geometry and size 09 match common ISO turning holders designed for rhombic inserts; ensure holder compatibility with the CCMT seat and clamping method. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T308-FW4 WSM30S FW4 Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating and the FW4 chipbreaker for stable chip control and extended tool life; the grade is specifically engineered for stainless steels and heat‑resistant alloys. Order the CCMT09T308-FW4 WSM30S directly via Metav Werkzeuge or contact our consultants for tailored cutting data and application support. CCMT09T308-FW4 WSM30S — Indexable turning insert, Tiger·tec Silver coating, 7° clearance (Walter Tools) A CCMT09T308-FW4 WSM30S indexable insert designed for precision turning of stainless steels and heat‑resistant superalloys, offering high wear resistance and dependable chip control for production environments Tiger·tec Silver coating for high wear resistance Suitable for stainless steels and superalloys FW4 chipbreaker for controlled chip formation 7° clearance and 0.8 mm corner radius Consistent cutting performance that reduces costs and downtime The combination of the Tiger·tec Silver coating and the WSM30S grade delivers a measurable improvement in wear resistance and tool life, which translates into fewer insert changes and reduced process interruptions. Designed for demanding materials, this solution supports secure chip formation when machining stainless steels and superalloys, minimising the risk of built-up edge and unpredictable tool wear. The result is a more economical production flow and consistent part quality, supporting tighter process windows and lowering overall machining costs. Controlled chip behaviour and reliable geometry for predictable results Geometry is crucial in turning operations: the FW4 chipbreaker is tuned for stable evacuation and predictable chip shapes, while the rhombus 80° form with 7° clearance and a 0.8 mm radius gives a balance between edge strength and finish capability. These features enable steady cutting forces and repeatable performance across batches. The insert’s form factor is compatible with standard CCMT toolholders, ensuring straightforward integration into existing toolsets and rapid changeover in multi‑shift production. Application flexibility and process security for production workshops With a tolerance class of M and a thickness of T3, this grade is suitable for serial production where reproducibility matters. The WSM30S grade is particularly effective on materials that are prone to work hardening or that generate high temperatures at the cutting zone, offering improved process security and surface integrity. Operators and process engineers benefit from the clear technical profile of the insert when selecting cutting data, making it easier to document and standardise setups across machines and sites. For application advice and supply of Walter Tools Tiger·tec Silver inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: CCMT09T308-FW4-WSM30S-WALTER Designation: CCMT09T308-FW4 ISO designation: CCMT09T308-FW4 WSM30S Manufacturer: Walter Tools Numbers / Core technical data Clearance angle: 7° Corner radius: 0.8 mm Plate size: 09 Thickness: T3 Tolerance class: M Plate form: Rhombus 80° Special features / Applications Coating: Tiger·tec Silver Grade: WSM30S Chipbreaker: FW4 Series: Tiger‑tec Silver Material suitability: S / M (superalloys/titanium and stainless steels) Product type: indexable turning insert FAQ Which materials is this insert designed for? The CCMT09T308-FW4 WSM30S from Walter Tools is optimised for stainless steels (M) and heat‑resistant superalloys (S), offering improved wear resistance and edge stability in these demanding material groups. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker promotes controlled chip formation and reliable evacuation, reducing the likelihood of entanglement and improving surface finish when using the CCMT09T308-FW4 WSM30S in turning operations. Is the geometry compatible with standard toolholders? Yes, the rhombus 80° form and CCMT designation mean the insert fits standard CCMT toolholders, enabling straightforward replacement and integration into existing turning tool assemblies. What advantage does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating enhances thermal and abrasive wear resistance, extending insert life under elevated cutting temperatures and contributing to consistent part quality with the WSM30S grade. Can Metav Werkzeuge supply cutting data for this insert? Metav Werkzeuge can provide recommended cutting parameters and availability information for the CCMT09T308-FW4 WSM30S; refer to the SKU CCMT09T308-FW4-WSM30S-WALTER when enquiring. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer Walter Tools.
CCMT09T308-MK4 WKK10S Wendeplatten - Walter Tools
High wear resistance and stable chip control deliver reliable performance in cast‑iron turning; the coated grade ensures long tool life and consistent surface quality for productive series machining. Order the CCMT09T308‑MK4 WKK10S directly via Metav Werkzeuge or ask our consultants if needed. CCMT09T308‑MK4 WKK10S — Rhombic 80° turning and boring insert, Tiger·tec Silver, Walter Tools A CCMT09T308‑MK4 WKK10S coated carbide insert designed for efficient machining of cast iron in turning and bore‑work, offering controlled chip formation and extended tool life. Tiger·tec Silver coating for wear resistance Optimised for cast‑iron machining Rhombic 80° form with 0.8 mm nose radius 7° clearance and MK4 chipbreaker design Increased productivity through a wear‑resistant coating The combination of the Tiger·tec Silver coating and the WKK10S grade provides pronounced resistance to abrasive wear typical of grey and nodular cast irons. This coated carbide technology reduces flank wear and extends service intervals, which in turn lowers tooling costs and minimises machine downtime. The result is a reliable cutting edge that keeps productivity high during repetitive turning operations while maintaining consistent dimensional accuracy. Better surface finish and chip control from optimised geometry The Rhombic 80° geometry paired with a 0.8 mm nose radius creates a favourable balance between cutting strength and accessibility, making the insert suitable for a wide range of turning and finishing passes. The MK4 chipbreaker is engineered to handle the short, brittle chips produced by cast iron, improving evacuation and reducing risk of built‑up edge. A 7° clearance angle helps prevent rubbing and supports smooth, repeatable surface finishes on components. Practical versatility for workshop and production environments Designed as a multi‑purpose turning and boring insert, the CCMT form supports both roughing and finishing steps when the process parameters are set accordingly. The insert’s specifications favour cast‑iron workpieces (ISO group K), offering predictable tool life and stable cutting behaviour. For operations seeking an economical, straightforward solution for series turning of cast‑iron parts, this insert provides a sound balance of performance and simplicity. Contact Metav Werkzeuge today to discuss Walter Tools inserts such as the CCMT09T308‑MK4 WKK10S for cast‑iron turning and secure tailored recommendations; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T308‑MK4‑WKK10S‑WALTER Designation: CCMT09T308‑MK4 ISO designation: CCMT09T308‑MK4 WKK10S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKK10S Product type: Boring/reboring and turning indexable insert Chipbreaker: MK4 Facts Clearance angle: 7° Corner radius: 0.8 mm Plate size: 09 Plate thickness: T3 Special features Coating: Tiger·tec Silver Material suitability: Gusseisen (cast iron) Plate form: Rhombic 80° Execution: T Tolerance class: M FAQ Which materials is this insert best suited for? The CCMT09T308‑MK4 WKK10S is optimised for cast iron (ISO group K) and is tuned to the abrasive wear and short‑breaking chips typical for these materials. What benefits does the Tiger·tec Silver coating provide? Tiger·tec Silver enhances wear resistance and cutting edge durability, improving tool life and consistency in machining cycles when using the WKK10S grade. Can the insert be used for both roughing and finishing? Yes, with appropriate parameter selection the rhombic 80° geometry and the MK4 chipbreaker allow both productive roughing and fine finishing steps. How does the MK4 chipbreaker affect chip formation? The MK4 chipbreaker promotes controlled, short chips for cast‑iron machining, aiding safe evacuation and reducing the likelihood of chip entanglement. Is this insert compatible with standard CCMT toolholders? The insert follows the CCMT designation and fits compatible toolholders designed for CCMT inserts; ensure correct clamping and seat condition for secure use. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer Walter Tools.
CCMT09T308-MK4 WKK20S WKK20S Wendeplatten - Walter Tools
The combination of Tiger‑tec Silver coating, the MK4 chipbreaker and the robust CCMT geometry delivers reliable, productive machining of cast iron components. Order the insert directly via Metav Werkzeuge or request technical consultancy if application advice is required. CCMT09T308-MK4 WKK20S drilling and turning indexable insert for cast iron, Tiger‑tec Silver, MK4 (Walter Tools) CCMT09T308-MK4 WKK20S is a versatile indexable insert designed for combined drilling/boring and turning operations in cast-iron applications Tiger‑tec Silver coating for enhanced wear resistance Optimised MK4 chipbreaker for controlled chip formation Rhombic 80° geometry for stable cutting performance 0.8 mm corner radius for durable cutting edge Durable coating for abrasive cast-iron machining The Walter grade WKK20S, produced within the Tiger‑tec Silver family, is a coated cemented carbide design optimised for abrasive cast-iron work. This grade balances hardness and toughness to resist the typical abrasive wear and the frequent short, breaking chips associated with cast materials. The result is extended tool life and predictable tool change intervals, which supports continuous production and reduces unplanned downtime. Geometry engineered for stability and repeatability A rhombic 80° cutting geometry combined with a 0.8 mm corner radius, 7° relief angle and T3 thickness gives the insert mechanical stability at the cutting edge and repeatable seating in the toolholder. The robust geometry reduces vibration in interrupted cuts and improves resistance to chipping, while the M tolerance class ensures consistent fit and reliable clamping across toolholders. These attributes support consistent surface quality and dimensional control in series production. Chip control that maintains throughput The integrated MK4 chipbreaker is designed to produce short, controllable chips when machining cast iron, reducing the risk of entanglement and ensuring uninterrupted operation. Controlled chip formation shortens cycle interruptions for chip evacuation and improves process reliability. Where intermittent cuts or varying depths are encountered, the chipbreaker helps maintain stable cutting forces and contributes to overall process security on the machine. Practical use and application advantages The insert is suitable for combined drilling and turning routines where flexibility and predictable performance are required. As a coated cemented carbide grade optimised for cast iron, it supports increased productivity through longer edge life and predictable wear behaviour. The insert designation and geometry allow easy integration into standard CCMT toolholders; cutting data should be selected in line with machine rigidity and component tolerances to exploit the full potential of the grade and chip control features. For application recommendations or to secure supply of Walter Tools CCMT09T308-MK4 WKK20S inserts, contact Metav Werkzeuge for direct ordering or specialist advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T308-MK4-WKK20S-WALTER Article designation: CCMT09T308-MK4 WKK20S Manufacturer: Walter Tools Product type: Drilling/boring and turning indexable insert SKU: CCMT09T308-MK4-WKK20S-WALTER Facts Relief angle: 7° Corner radius: 0.8 mm Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKK20S Coating: coated cemented carbide Chipbreaker: MK4 Application: drilling and turning Suitable for: cast iron FAQ What materials is this insert intended for? The CCMT09T308-MK4 WKK20S insert is developed primarily for machining cast iron, using the WKK20S grade within the Tiger‑tec Silver family. How does the MK4 chipbreaker help in production? The MK4 chipbreaker produces short, controllable chips when cutting cast iron, reducing chip-related interruptions and supporting continuous throughput with improved process stability. Which features contribute most to edge life? The combination of Tiger‑tec Silver coating, the robust 0.8 mm corner radius and the insert’s Rhombic 80° geometry delivers enhanced wear resistance and reliable edge strength, prolonging service life. Is the insert suitable for both turning and drilling operations? Yes, the insert’s designation and geometry support combined drilling and turning routines; appropriate toolholder selection and cutting data are recommended for optimal results. What tolerance and fit can be expected for the insert? The insert is manufactured to an M tolerance class, ensuring consistent seating and repeatable clamping accuracy in compatible toolholders. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanation. There is no relationship between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
CCMT09T308-MM4 WMP20G MM4 Wendeplatten - Walter Tools
The Tiger·tec Gold grade and WMP20G coating ensure stable chip formation and extended edge life in stainless steel machining; combined with the 0.8 mm corner radius and MM4 chipbreaker, this insert gives consistent surface quality and reliable cycle times. Order the CCMT09T308-MM4 WMP20G directly via Metav Werkzeuge or ask our consultants if needed. CCMT09T308-MM4 WMP20G indexable insert for stainless steel machining — Walter Tools The CCMT09T308-MM4 WMP20G is an indexable insert engineered for turning and boring tasks on stainless steel, offering robust performance under medium to heavy cutting conditions. Tiger·tec Gold coated carbide Optimised for stainless steel machining 7° clearance for stable cutting 0.8 mm corner radius for edge strength Greater productivity through material-adapted grade and coating The WMP20G grade, part of the Tiger·tec Gold series, is a coated carbide specifically formulated for machining stainless steel, a group of alloys prone to work hardening and poor chip control. Thanks to the coating’s thermal resilience and the substrate’s toughness, the insert supports stable chip formation, reducing the risk of built-up edge and improving process security. This translates into more predictable tool life and fewer interruptions on the shop floor, which benefits cycle times and overall throughput. Geometry and edge design that improve process reliability Built in a Rhombus 80° shape with 7° clearance, the insert provides a secure seating and a geometry that helps control cutting forces during interrupted or continuous cuts. The 0.8 mm radius increases edge strength for tougher engagement and contributes to a consistently good surface finish when roughing into finish passes. The MM4 chipbreaker has been designed to manage stainless steel chips effectively, lowering the likelihood of entangling or ropey chips and supporting steady heat dissipation, which helps maintain dimensional accuracy over longer runs. Practical benefits for workshop efficiency and tool management The insert’s dimensions and chip control features simplify process parameter setting and make tool life more predictable, supporting lean production practices. Compatibility with common toolholders for CCMT-style inserts means fast indexation and minimal setup time, while the robust grade reduces the frequency of insert changes. Combined, these aspects promote lower machine downtime and better overall equipment effectiveness. Application advice is available from Metav Werkzeuge to match holder choice and cutting data to the intended stainless steel grade and operation. For tailored application support or availability of the Walter Tools CCMT09T308-MM4 WMP20G insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for fast, expert guidance and supply Technical Data Article number: CCMT09T308-MM4-WMP20G-WALTER Designation: CCMT09T308-MM4 WMP20G Product type: Drilling/boring and turning indexable insert Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Clearance angle: 7° Corner radius: 0.8 mm Insert size: 09 Insert thickness: T3 Tolerance class: M Special features Chipbreaker: MM4 Geometry: Rhombus 80° Grade: WMP20G (coated carbide) Material group: M (for stainless steel) Execution: T FAQ Is this insert suitable for machining stainless steel? Yes. The CCMT09T308-MM4 WMP20G insert from Walter Tools is formulated for stainless steel and the Tiger·tec Gold coating helps control chips and heat when cutting these alloys. What advantages does the MM4 chipbreaker provide? The MM4 chipbreaker on this insert improves chip control during stainless steel turning, promoting consistent chip shapes and reducing the risk of built-up edge and chip entanglement for safer, more stable machining. Can the insert deliver a good surface finish on final passes? Yes. The combination of the 0.8 mm corner radius and the Tiger·tec Gold grade supports improved edge strength and stable cutting, which assists in achieving a reliable surface finish in finish and semi-finish operations. Is this insert compatible with standard CCMT toolholders? The CCMT09T308-MM4 WMP20G follows the CCMT indexable insert geometry and is compatible with holders designed for that format; correct clamping and seat condition remain important for best results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product from the manufacturer.
CCMT09T308-MM4 WMP20S MM4 Wendeplatten - Walter Tools
Take advantage of high process stability and optimised chip control for reliable stainless steel turning; the combination of Tiger·tec Silver coating and an MM4 chipbreaker reduces rework and extends tool life. Specify availability via Metav Werkzeuge for fast delivery and technical consultation. CCMT09T308-MM4 WMP20S turning insert — Walter Tools, Tiger·tec Silver, suited for stainless steel, 7° relief CCMT09T308-MM4 WMP20S is an indexable turning and boring insert designed for machining stainless steels with robust chip control and consistent cutting performance Tiger·tec Silver coating for stainless steel Stable chip formation under tough conditions Rhombic 80° geometry, 7° relief angle Improved cutting reliability for stainless steels The combination of the WMP20S grade and Tiger·tec Silver technology offers a coated carbide solution optimised for the challenges of machining stainless steel. The cutting material supports secure chip formation where work-hardening and built-up edge can otherwise disrupt production. With the MM4 chipbreaker the insert promotes predictable chip segmentation and evacuation, which directly reduces stoppages and the risk of surface defects. This increases overall process efficiency and contributes to lower scrap rates. Geometry that delivers repeatable surface quality The rhombic 80° insert geometry, in conjunction with a 7° relief angle and a 0.8 mm nose radius, provides controlled engagement and stable cutting forces. The Rhombic 80° form is particularly suited to both profile turning and light shoulder work, allowing a balance between accessibility and strength. The T3 thickness ensures sufficient support for the cutting edge, improving repeatability when clamped in standard tool holders and helping to maintain a consistent surface finish across multiple components. Practical benefits for production workflows Adopting this grade and geometry reduces tool change frequency and supports stable machining windows in medium to robust operating conditions. The insert’s design enables straightforward integration into existing tool assemblies and minimises adjustment time on the shop floor. Backed by the reputation of Walter Tools, this solution contributes to a predictable production routine, helping to meet batch tolerances and maintain cycle-time targets with fewer interruptions. For reliable stainless steel performance specify the CCMT09T308-MM4 WMP20S from Walter Tools and contact Metav Werkzeuge for availability and application advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CCMT09T308-MM4-WMP20S-WALTER Designation: CCMT09T308-MM4 WMP20S Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.8 mm Insert size: 09 Thickness: T3 Chipbreaker: MM4 Special features Series: Tiger·tec Silver Grade: WMP20S (coated carbide) Geometry: Rhombic 80° Material group: M (stainless steels) Application focus: stainless steel machining FAQ What materials is this insert intended for? This insert is specified for stainless steel applications; the WMP20S grade and Tiger·tec Silver technology support secure chip control when machining ISO M materials. How does the Tiger·tec Silver coating benefit processing? The Tiger·tec Silver coating on the CCMT09T308-MM4 improves wear resistance and thermal stability, helping the cutting edge remain sharp longer under stainless steel cutting conditions. Is the insert suitable for finishing operations? Yes, the combination of 0.8 mm nose radius and the rhombic 80° geometry provides good control for finishing and light profiling tasks with consistent surface quality. Which chipbreaker is fitted and what does it do? The insert uses an MM4 chipbreaker designed to promote stable chip formation and reliable evacuation in tougher cutting scenarios. Can this insert be used in existing tool holders? The CCMT form and dimensions follow standard insert interfaces, enabling compatibility with commonly used holders for turning and boring. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, brand-new product of the manufacturer.
CCMT09T308-MM4 WMP30G MM4 Wendeplatten - Walter Tools
Take advantage of the combination of proven chip control, robust edge stability and the Tiger·tec Gold coating for consistently productive stainless steel machining; order this insert directly via Metav Werkzeuge or consult our specialists for tailored recommendations. Drilling and turning indexable insert CCMT09T308-MM4 WMP30G for stainless steel – Walter Tools The CCMT09T308-MM4 WMP30G is a rhombic 80° indexable insert engineered for medium to heavy-duty machining of stainless steels, offering reliable chip formation and repeatable edge life. Tiger·tec Gold coating for process security Optimised MM4 chipbreaker for stable chips Rhombic 80° geometry, 0.8 mm corner radius Suitable for stainless steel machining Increased productivity through stable chip control The Tiger·tec Gold series grade delivers a combination of a high-performance coating and a wear-resistant substrate that together promote stable chip formation when cutting austenitic and other stainless steels. The integrated MM4 chipbreaker is designed to control chip flow at moderate to robust cutting parameters, which reduces interruptions for chip evacuation and minimises the risk of built-up edge. For production environments seeking higher throughput, this translates into fewer tool changes and a smoother process window without sacrificing surface quality. Reliable edge life and geometry for demanding operations The insert’s rhombic 80° shape with a 0.8 mm corner radius provides versatility between finishing and semi-finishing passes while the 7° clearance angle helps to reduce rubbing and heat generation at the cutting zone. These geometry choices support consistent contact conditions and reduce mechanical stress on the cutting edge, delivering improved tool life in tougher stainless steel grades. The nominal plate size and thickness mean stable seating in standard CCMT toolholders, helping to maintain reproducible results across batches. Simple specification and secure material match Specified as a coated carbide grade developed for material group M, the WMP30G designation indicates a Walter-developed solution optimised for stainless steel machining challenges, such as stickiness and work hardening. The insert is supplied in the ISO-style designation CCMT09T308-MM4, enabling straightforward selection against tooling data sheets and ensuring compatibility with common turning and drilling-holder systems. The robust indexable design supports predictable performance in series production and single-piece flow alike. Coating, substrate and application explained The Tiger·tec Gold technology combines a layered PVD/CVD-coated surface with a substrate tuned to resist crater wear and flank degradation. In practical terms, the coating reduces friction and thermal loading while the substrate sustains cutting-edge stability under intermittent loads typical in stainless steel operations. For workshops that run mixed lots or face variable material batches, this insert offers a balance of reliability and economy, reducing scrap risk and stabilising process capability indicators. Practical handling and tooling considerations The insert’s T3 thickness and CCMT format are compatible with standard tool clamps for turning and certain drilling/reaming adaptors; the rhombic form is suitable where approach angles and tool overhang vary. When paired with correctly selected cutting data for stainless steels, the combination of MM4 chip control and Tiger·tec Gold coating helps to maintain target surface finishes without excessive cycle-time increases. For optimisation support, Metav Werkzeuge can provide cutting data examples and selection advice for holder and grade pairing. Contact Metav Werkzeuge today at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss the CCMT09T308-MM4 WMP30G and secure the best inserts for stainless steel machining in specific applications Technical data Article number: CCMT09T308-MM4-WMP30G-WALTER Designation: CCMT09T308-MM4 WMP30G Manufacturer: Walter Tools Facts Series: Tiger-tec Gold Grade: WMP30G Plate form: Rhombus 80° Plate size: 09 Plate thickness: T3 Corner radius: 0.8 mm Clearance angle: 7° Chipbreaker: MM4 Material group: M (stainless steel) Special features Coated carbide grade optimised for stainless steel Designed for stable chip formation in medium to robust conditions Rhombic geometry for versatile turning and drilling use Standard CCMT format for common toolholders Walter Tools original product FAQ What materials is this insert intended for? The CCMT09T308-MM4 WMP30G is formulated for machining stainless steel (material group M) and performs best under medium to robust cutting conditions typical for these alloys. What does the MM4 chipbreaker do? The MM4 chipbreaker on the CCMT09T308-MM4 promotes consistent chip control and curl when machining stainless steel, reducing entanglement and improving process reliability. Can the insert be used in standard CCMT toolholders? Yes, the ISO designation CCMT09T308-MM4 indicates compatibility with standard CCMT-format holders commonly used for turning and certain drilling/reaming adaptors. How does the Tiger·tec Gold coating benefit production runs? Tiger·tec Gold provides a low-friction, wear-resistant surface that reduces thermal loading and helps maintain flank and crater wear resistance, thereby extending effective tool life in serial production. What geometry features support surface finish and tool life? The rhombic 80° form combined with a 0.8 mm corner radius and a 7° clearance angle helps to balance cutting forces and heat generation, supporting consistent surface quality and longer edge life. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
CCMT09T308-MM4 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of edge stability and reliable chip control for consistent component quality and longer tool life; the robust MM4 chipbreaker and Tiger‑tec Silver coating ensure stable cutting in stainless steels and superalloys. Order the insert directly via Metav Werkzeuge or consult our specialists for selection and application advice. CCMT09T308‑MM4 WSM01 indexable insert — Rhombic 80° geometry, 7° clearance | Walter Tools The CCMT09T308‑MM4 WSM01 is a coated carbide indexable insert designed for demanding turning and boring tasks, especially suited to stainless steels and heat‑resistant superalloys. Tiger‑tec Silver coating for edge stability Optimised MM4 chipbreaker for stainless steels Rhombic 80° form for versatile turning operations 0.8 mm corner radius for consistent surface finish Stable machining of stainless steels and superalloys for fewer interruptions The combination of the WSM01 grade and the Tiger‑tec Silver coating produces a cutting edge with improved thermal resistance and reduced tendency to build up material. For components made from stainless steels or heat‑resistant alloys, this leads to more reliable chip formation and fewer unscheduled tool changes. The MM4 chipbreaker is engineered to control chips in tough, gummy materials, which reduces manual intervention and helps maintain steady cycle times on production runs. Geometry tuned for dimensional consistency and surface finish The Rhombus 80° shape with a 7° clearance angle provides a balance between cutting edge strength and accessibility in shoulder and finishing cuts. A 0.8 mm corner radius supports a consistent surface finish while avoiding excessive cutting forces, which is particularly important when machining parts that require repeatable tolerances. Where accuracy matters, the tolerance class M ensures predictable insert dimensions for secure seating in toolholders and repeatable part results. Robust design that lowers unit cost and simplifies logistics Made as a coated carbide insert, this grade is intended for extended service life under thermal and mechanical stress. The plate thickness and T3 execution provide the rigidity needed for interrupted cuts and mixed‑operation turning. Taken together, the reduced scrap risk and longer indexable life contribute to a lower cost per component over extended production runs. For shops aiming to improve throughput without changing machining strategy, this insert offers an efficient path to more productive turning operations. For precision machining of stainless steels and superalloys with Walter Tools Tiger‑tec Silver inserts, contact Metav Werkzeuge for tailored recommendations and compatibility guidance. Technical data Article number: CCMT09T308-MM4-WSM01-WALTER Designation: CCMT09T308-MM4 WSM01 Series: Tiger‑tec Silver Grade: WSM01 Core data Clearance angle: 7° Corner radius: 0.8 mm Insert size: 09 Thickness: T3 Geometry: Rhombus 80° Chipbreaker: MM4 Tolerance class: M Features & applications Coating: Tiger‑tec Silver (coated carbide) Material suitability: stainless steels, heat‑resistant superalloys / titanium (S / M) Execution: T Typical uses: turning and boring operations, stable chip control, finishing and semi‑finishing FAQ What materials is this insert suitable for? The CCMT09T308‑MM4 WSM01 insert is formulated for stainless steels and heat‑resistant superalloys/titanium, combining the WSM01 grade with Tiger‑tec Silver coating for improved thermal stability. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker improves chip control in gummy and work‑hardening materials, helping to avoid built‑up edge and promoting continuous, safe chip flow during turning tasks. Will the 0.8 mm corner radius affect dimensional accuracy? A 0.8 mm corner radius offers a compromise between edge strength and surface finish; it helps maintain consistent part geometry while delivering improved tool life compared with very fine radii. Is the insert suitable for finishing operations? Yes, the combination of the Rhombus 80° geometry and the specified corner radius makes this insert suitable for finishing and light semi‑finishing passes where surface quality and repeatability are required. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory‑new product from the manufacturer (Walter Tools).
CCMT09T308-MM4 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of reliable edge life, Tiger·tec Silver coating and a geometry optimised for stainless steels to keep production steady and minimise downtime. Order Walter Tools inserts directly via Metav Werkzeuge for fast supply and expert advice. CCMT09T308-MM4 WSM10S indexable insert — Tiger·tec Silver coating, for stainless steels | Walter Tools The CCMT09T308-MM4 WSM10S is an indexable turning and boring insert engineered for demanding machining of stainless steels and heat‑resistant alloys in industrial production. Tiger·tec Silver coating WSM10S grade for stainless steels Rhombic 80° geometry for versatile use 0.8 mm corner radius for reliable edge life Consistent cutting performance for demanding materials The coated carbide composition and the WSM10S grade deliver consistent performance when machining stainless steels and heat‑resistant superalloys. The combination of a wear‑resistant coating and a substrate tuned for toughness supports stable chip formation and reduces the risk of built‑up edge under thermally aggressive cutting. This stability translates into fewer unplanned tool changes and a more predictable production rhythm, improving overall process efficiency. Coating and grade designed to extend tool life The Tiger·tec Silver coating enhances heat resistance and abrasion protection, which is particularly relevant when processing materials that generate high cutting temperatures. The grade balances toughness and hardness to sustain a sound cutting edge, so the insert maintains dimensional reliability over longer tool life. For production planners this means lower tooling consumption and more consistent component quality across batch runs. Geometry and chip control that protect the edge A rhombic 80° form with a dedicated MM4 chipbreaker provides reliable chip control in turning and light boring operations, supporting smooth evacuation even with sticky alloys. The 0.8 mm corner radius and a 7° clearance angle combine to deliver robust edge strength while preserving surface finish, making the insert suitable for applications where edge stability and repeatability are priorities rather than aggressive metal removal in a single pass. Integration into machining processes and handling benefits The insert’s designation and familiar CCMT form factor make it straightforward to integrate into standard toolholders, simplifying inventory and setup. As a coated indexable solution from a recognised brand, it supports consistent process parameters and helps maintain reproducible component tolerances. Where process security and traceable tool performance are required, this type of insert contributes to predictable cycle times and reduced scrap rates. Contact Metav Werkzeuge for application recommendations, stock availability and to order Walter Tools CCMT09T308-MM4 WSM10S inserts for immediate use in stainless steel machining operations Technical Data SKU: CCMT09T308-MM4-WSM10S-WALTER Designation: CCMT09T308-MM4 ISO designation: CCMT09T308-MM4 WSM10S Series: Tiger·tec Silver Grade: WSM10S Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.8 mm Plate size: 09 Thickness: T3 Special features Chipbreaker: MM4 Form: Rhombic 80° Coating technology: Tiger·tec Silver Applicable material groups: S / M (heat‑resistant alloys, titanium and stainless steels) Tolerance class: M FAQ What materials is this insert suitable for? The CCMT09T308-MM4 WSM10S insert is intended for stainless steels (ISO M) and can also be used for heat‑resistant superalloys and titanium (ISO S) depending on geometry and cutting conditions. What benefit does the Tiger·tec Silver coating provide? Tiger·tec Silver enhances heat and wear resistance on the insert, which helps to maintain a stable cutting edge and improves service life in thermally demanding stainless steel machining. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker is designed to control chip shape and evacuation in turning and light boring, reducing the chance of entanglement and supporting consistent surface quality. Is the CCMT form compatible with standard toolholders? Yes, the CCMT09T308-MM4 format corresponds to common CCMT indexable insert holders, facilitating easy replacement and inventory integration. What does the 0.8 mm corner radius imply for surface finish? A 0.8 mm corner radius offers a compromise between edge strength and finish—providing improved edge robustness while still achieving a good surface quality on most stainless steel turning applications. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original, factory‑new goods of the manufacturer.
CCMT09T308-MM4 WSM20S MM4 Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger·tec Silver coating and the MM4 chipbreaker for stable chip control and extended edge life; the result is reliable, productive machining of demanding alloys. Order the insert directly via Metav Werkzeuge or consult our technical advisers for cutting-data optimisation. CCMT09T308-MM4 WSM20S turning insert by Walter Tools — Tiger·tec Silver, for rostfreier Stahl and superalloys The CCMT09T308-MM4 WSM20S is a coated carbide turning insert designed for heavy-duty and finish turning of rostfreier Stahl and heat-resistant superalloys, offering a balance of edge stability and wear resistance in demanding production environments Tiger·tec Silver grade WSM20S Suitable for rostfreier Stahl and superalloys Rhombic 80° insert form MM4 chipbreaker for consistent chips Reliable performance on difficult-to-machine alloys The insert is built around the WSM20S grade within the Tiger·tec Silver family, a coated carbide formulation optimised for applications where temperature and material toughness challenge tool life. The MM4 chipbreaker promotes predictable chip formation, reducing interruption from long, stringy chips and helping maintain a steady process. For shops processing rostfreier Stahl (ISO group M) and heat-resistant alloys (ISO group S), this combination reduces rework and increases effective cutting time, supporting higher overall throughput with fewer unscheduled tool changes. Geometry that balances strength and versatility A rhombic 80° shape with a 7° relief angle provides a robust cutting edge and access for common turning operations; the 0.8 mm corner radius absorbs cutting loads and improves finish when used in light- to medium-depth cuts. The T3 insert thickness and the CCMT-style pocket compatibility ensure secure clamping and stability under moderate radial forces. In practical terms, these geometry choices translate into smoother surface quality and an extended margin against edge chipping when compared with more acute geometries. Process benefits: consistency, longevity and predictability Using an insert from the Tiger·tec Silver family supports greater process reliability via optimised coating properties and a stable substrate. The result is longer tool life and consistent component quality across batch runs. The insert’s design helps to maintain cutting-edge integrity at elevated temperatures typical of rostfreier Stahl and superalloy machining, which in turn reduces machine downtime and improves cost-efficiency per component. For production engineers, that means more predictable planning and less variation between shifts. Contact Metav Werkzeuge for tailored cutting data and fast availability of Walter Tools inserts — our consultants will advise on insert selection and recommended cutting parameters. Technical data SKU: CCMT09T308-MM4-WSM20S-WALTER Designation: CCMT09T308-MM4 WSM20S turning insert Manufacturer: Walter Tools Core specifications Relief angle: 7° Corner radius: 0.8 mm Insert size: 09 Thickness: T3 Tolerance class: M Materials & features Grade/series: Tiger·tec Silver — WSM20S Chipbreaker: MM4 Insert form: Rhombic 80° Applicable material groups: rostfreier Stahl (M), superalloys / titanium alloys (S) Execution: T Applicable material codes: S / M FAQ What materials is this insert intended for? The CCMT09T308-MM4 WSM20S insert is specified for rostfreier Stahl (ISO group M) and heat-resistant superalloys (ISO group S), offering temperature-resistant performance and controlled chip formation. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker produces short, manageable chips and stabilises cutting forces, which improves process consistency and reduces interruptions during turning operations with challenging materials. Which features increase tool life in this grade? The combination of the Tiger·tec Silver coating and the WSM20S carbide grade enhances wear resistance at elevated temperatures, while the geometry (0.8 mm corner radius, rhombic 80°) protects the cutting edge against chipping. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T308-MM4 WSM30S MM4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WSM30S grade for stable chip formation and extended edge life; the insert's Rhombic 80° geometry and 0.8 mm corner radius deliver strength and accessibility for demanding turning tasks. Order the CCMT09T308-MM4 WSM30S inserts via Metav Werkzeuge or consult our specialists for application-specific cutting data. CCMT09T308-MM4 WSM30S turning insert, Tiger·tec Silver — designed for rostfreier Stahl and heat-resistant alloys (Walter Tools) The CCMT09T308-MM4 WSM30S is a rhombic 80° turning insert developed for heavy-duty and difficult-to-machine materials, offering a balance of edge stability and chip control for modern production environments Tiger·tec Silver coating MM4 chipbreaker for controlled chips Suitable for rostfreier Stahl and superalloys Rhombic 80° form with 0.8 mm radius Consistent productivity when machining rostfreier Stahl and superalloys The combination of the Tiger·tec Silver coating and the WSM30S grade provides a clear productivity advantage when processing rostfreier Stahl and heat-resistant alloys. The advanced coating reduces thermal load and wear on the cutting edge, which translates into longer tool life and fewer indexings per workpiece. For production-oriented shops this means higher uptime and reduced tooling costs over time. The coated substrate supports a robust cutting edge that resists built-up edge and maintains dimensional consistency during extended runs. Reliable chip control and edge integrity for safer turning Built-in MM4 chip control ensures predictable chip breaking under a wide range of cutting conditions, improving swarf handling and machine safety. The 0.8 mm corner radius smooths load transitions at the cutting edge and reduces the tendency for notch formation during interrupted cuts. As a result, the insert promotes stable chip formation and reduces the need for secondary finishing, which benefits both cycle time and surface quality in serial production. Geometry that balances strength and access for varied applications The Rhombic 80° profile combines penetrating geometry with sufficient edge support to withstand moderate depths of cut. With a clearance angle of 7° and a plate thickness of T3, the insert is designed to offer a compromise between rigidity and cutting accessibility in confined tool holders. This geometry supports reliable performance in facing and turning operations where tool overhang or limited approach angles would otherwise restrict insert choice. Material grouping and recommended use cases explained The insert is optimised for ISO material groups M and S, meaning it is particularly suited to rostfreier Stahl (M) and heat-resistant superalloys or titanium (S). Materials in these groups generate heat at the cutting zone and can produce long, stringy chips; the WSM30S grade and the MM4 chipbreaker help to mitigate these issues by improving thermal resistance and chip breaking. For customers less familiar with ISO grouping: M = stainless steels; S = hot-work steels, superalloys and titanium. Selecting appropriate cutting data and coolant strategies further enhances tool life and process reliability. Contact Metav Werkzeuge for tailored cutting data, fast supply of Walter Tools CCMT09T308-MM4 WSM30S inserts and expert application advice Technical data Article number: CCMT09T308-MM4-WSM30S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte CCMT09T308-MM4 WSM30S Walter Tools Manufacturer: Walter Tools Grade: WSM30S Series: Tiger-tec Silver Material group: S / M Plate form: Rhombus 80° Relief angle: 7° Corner radius: 0.8 mm Plate size: 09 Thickness: T3 Chipbreaker: MM4 Facts Corner radius: 0.8 mm Relief angle: 7° Plate size designation: 09 Thickness: T3 Tolerance class: M Special features Coating technology: Tiger·tec Silver Substrate type: coated carbide Chip control: MM4 chipbreaker Main application: rostfreier Stahl and heat-resistant superalloys (ISO M / S) Series characteristics: designed for stable edge life and broad material coverage FAQ What materials is this insert suitable for? The CCMT09T308-MM4 WSM30S insert is specified for ISO groups M and S, making it suitable for rostfreier Stahl and heat-resistant superalloys depending on geometry and cutting data. How does the Tiger·tec Silver coating benefit performance? The Tiger·tec Silver coating on the WSM30S grade improves thermal resistance and wear behaviour, which enhances edge life and process stability in demanding turning applications. Which chipbreaker should be expected and what is its effect? This insert uses the MM4 chipbreaker, designed to produce controlled, short chips in a wide range of feed and depth combinations, aiding safe chip disposal and consistent surface finish. Can the insert handle interrupted cuts and heavier engagement? The Rhombic 80° geometry together with the 0.8 mm corner radius provides robust edge support that tolerates moderate interruptions and heavier engagement better than sharper radii. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is original factory-new goods of the manufacturer.
CCMT09T308-MP4 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of Walter Cermet cutting grade and the MP4 chipbreaker for consistent chip control and reliable finishing. The rhombic 80° geometry with a 7° rake angle and a 0.8 mm corner radius combines versatility and precision for turning and boring operations. Order directly via Metav Werkzeuge or consult their specialists for application-specific setup and tool recommendations. CCMT09T308-MP4 WEP10C – Turning and boring indexable insert with MP4 chipbreaker by Walter Tools The CCMT09T308-MP4 WEP10C is a rhombic 80° indexable insert from the Walter Cermet series, engineered for stable chip formation and precise finishing in a broad range of machining tasks. Walter Cermet WEP10C grade MP4 chipbreaker for stable chips Rhombic 80° geometry 7° rake angle for adaptable turning Reliable performance through cermet cutting grade The combination of Walter Cermet technology and the WEP10C grade delivers a balance of wear resistance and surface quality that benefits medium- to high-speed finishing. Cermet grades are optimised for fine finishes and reduced built-up edge, so abrasive wear is minimised while dimensional stability is maintained. This results in fewer tool changes and steadier process outputs, which contributes directly to lower cycle-time variability and improved workpiece quality. Consistent chip control and improved surface finish The dedicated MP4 chipbreaker shapes chips reliably across varying depths of cut, reducing clogging and the risk of interrupted cutting. Stable chip evacuation supports consistent contact conditions at the cutting edge, helping to achieve repeatable surface roughness and extending the interval between inspections. For applications where finish and repeatability matter, this insert offers tangible process advantages over general-purpose grades. Versatile geometry for turning and boring operations The rhombic 80° insert geometry combined with a 7° rake angle enables flexible use in both turning and light boring operations. The 0.8 mm corner radius supports controlled engagement when moderate radii are required, while the compact T3 thickness maintains rigidity in confined tool pockets. This geometry is particularly useful when alternating between external profiling and internal diameter adjustments on multi-operation setups. Practical integration and toolholder compatibility Designed for standard indexable systems, the insert’s CCMT form ensures straightforward seating and orientation in commonly used toolholders. The tolerance class M offers a reliable fit that reduces micro-movements during cutting, helping to preserve edge life and part accuracy. Check the product matrix for specific material suitability and verify that the chosen toolholder supports the insert thickness T3 and seat form for optimal clamping stability. Contact Metav Werkzeuge for tailored advice on integrating the Walter Tools CCMT09T308-MP4 WEP10C into production and to identify the best holder and parameters for the application Technical data SKU: CCMT09T308-MP4-WEP10C-WALTER Designation: CCMT09T308-MP4 WEP10C Manufacturer: Walter Tools Product type: Boring and turning indexable insert Facts Free angle: 7° Corner radius: 0.8 mm Insert size: 09 Thickness: T3 Tolerance class: M Special features Series: Walter Cermet Grade: WEP10C (cermet) Chipbreaker: MP4 Insert shape: Rhombus 80° Execution: T Material specification: catalogue-dependent Note: Check the product matrix for workpiece material suitability FAQ What materials is this insert suitable for? The CCMT09T308-MP4 WEP10C is a cermet-grade insert from Walter Tools; suitability depends on the specific workpiece material and should be verified against the product matrix provided by the manufacturer. How does the MP4 chipbreaker improve machining? The MP4 chipbreaker on the CCMT09T308-MP4 WEP10C promotes controlled chip formation and evacuation, reducing interruptions and supporting consistent surface finish when machining finishing passes. Can this insert be used for both external turning and boring? Yes, the rhombic 80° geometry and 7° rake angle make the insert versatile for external turning and light boring tasks; confirm holder compatibility for best results. What is the significance of the WEP10C grade? WEP10C is a Walter cermet grade formulated for good surface quality and wear resistance in finishing applications; reference the grade description for detailed application limits. Does the tolerance class M affect toolholder selection? Tolerance class M indicates the manufacturing tolerance of the insert and supports reliable seating; ensure the toolholder matches the CCMT form and T3 thickness for secure clamping. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the named brands. The offered item is an original, factory-new product from the manufacturer.
CCMT09T308-MP4 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating, an MP4 chipbreaker and a 0.8 mm corner radius for consistent chip control and long tool life in steel machining; order directly via Metav Werkzeuge or request advice from our consultants for the best application setup. CCMT09T308-MP4 WPP10G – Rhombic 80° turning and boring insert by Walter Tools, Tiger‑tec Gold coated, for steel machining The CCMT09T308-MP4 WPP10G is a rhombic 80° indexable insert designed for turning and boring tasks, optimised specifically for machining steel under ISO P conditions. Tiger‑tec Gold coated cutting grade WPP10G Optimised for steel machining (ISO P) MP4 chipbreaker for reliable chip control Rhombic 80° form with 0.8 mm nose radius Reliable wear resistance that extends productive runtime The Tiger‑tec Gold coating used on this grade delivers a balanced combination of wear resistance and toughness, so tool life is extended even under the thermal loads typical for steel. Coated cemented carbide technology reduces flank and crater wear, which leads to fewer insert changes and more predictable machining cycles. For production environments where consistent output and reduced downtime matter, this coated grade provides an efficient route to stable process windows while preserving workpiece quality. Stable chip formation and improved surface finish Thanks to the MP4 chipbreaker and the rhombic 80° geometry, chip flow is controlled and evacuation is reliable during both roughing and light finishing operations. The moderate 0.8 mm corner radius supports good surface integrity while still allowing reasonable cutting parameters. The result is fewer interruptions from built-up edge and consistently repeatable surface finishes, which simplifies downstream operations and reduces rework. Optimised for steel — predictable performance across material grades This insert is specified for the ISO P material group and is therefore suited to unalloyed and alloyed steel grades. The grade WPP10G is engineered for a broad steel coverage with a balance between wear resistance and toughness, making it suitable for a wide range of cutting conditions. The plate thickness T3 and tolerance class M provide mechanical stability and reproducible clamping behaviour, which helps maintain dimensional consistency in serial production and tool exchanges. Contact Metav Werkzeuge for tailored application advice or to discuss the best cutting data for Walter Tools Tiger‑tec Gold inserts and compatible toolholders Technical data Article number: CCMT09T308-MP4-WPP10G-WALTER Designation: CCMT09T308-MP4 WPP10G Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.8 mm Plate form: Rhombic 80° Plate size: 09 Plate thickness: T3 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WPP10G (coated cemented carbide) Chipbreaker: MP4 Material application: suitable for steel (ISO P) Intended use: turning and boring indexable insert FAQ What materials is this insert suitable for? The CCMT09T308-MP4 WPP10G insert is designed for the ISO P material group and is suitable for machining unalloyed and alloyed steel. How does the Tiger‑tec Gold coating improve performance? The Tiger‑tec Gold coating on the WPP10G grade increases wear resistance while retaining toughness, resulting in longer insert life and more consistent cutting performance on steel components. Which chipbreaker should be selected for stable chips? The MP4 chipbreaker on this indexable insert is intended for reliable chip control across common steel machining operations and supports secure evacuation in both continuous and interrupted cuts. Is the 0.8 mm corner radius suitable for finishing? A 0.8 mm corner radius strikes a balance between strength and surface finish, making it appropriate for light finishing and general-purpose turning where a smooth surface and tool robustness are required. Can this insert be used in production cycles requiring repeatable tolerances? Yes; with its T3 plate thickness and M tolerance class, the insert provides mechanical stability and repeatable clamping behaviour suitable for serial production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CCMT09T308-MP4 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of long tool life, consistent chip control and straightforward integration into existing turning processes for predictable productivity in steel machining. Order the insert directly via Metav Werkzeuge or consult our team for process parameters and availability. CCMT09T308-MP4 WPP20G — indexable turning insert, 0.8 mm corner radius, Walter Tools The CCMT09T308-MP4 WPP20G is an indexable turning insert optimised for steel machining, offering robust edge strength and reliable chip control for general turning applications. Tiger·tec Gold coating for steel machining MP4 chipbreaker for controlled chips 0.8 mm corner radius for robust edges Rhombic 80° profile for versatile turning Increased throughput through stable edge performance The combination of the WPP20G grade and Tiger·tec Gold coating delivers improved wear resistance and longer tool life when turning steels. The coated cemented carbide substrate reduces flank wear under cyclic loads, which translates into fewer insert changes and more consistent cycle times. This stability supports higher feed rates and enables predictable production planning in batch and single-piece flows. Controlled chip formation for safer, cleaner machining Equipped with the MP4 chipbreaker, this indexable insert promotes regular chip segmentation during longitudinal and transverse turning of steels. The chip control reduces the risk of entangling swarf and improves surface finish by maintaining a stable cutting zone. For shop floors where machine accessibility and operator safety are priorities, this behaviour minimises manual intervention and downtime. Robust geometry for flexible cutting strategies The Rhombic 80° shape combined with a 0.8 mm corner radius and a 7° clearance angle offers a balance between strength and accessibility for shoulder cuts and general turning operations. The geometry supports moderate depths of cut while protecting the cutting edge from mechanical overload, making it suitable for a wide range of workpiece geometries without compromising component accuracy. Simple specification and reliable tolerance class The insert is supplied in tolerance class M and the standard CCMT designation provides clear compatibility with common toolholders. As a coated carbide grade intended for ISO P applications, it is particularly suitable for unalloyed and alloyed steels where typical heat generation and chip formation characteristics are expected. This specification assists process planners and purchasing in matching the right grade to the application with confidence. For process advice or to secure stock of the Walter Tools CCMT09T308-MP4 WPP20G insert, contact Metav Werkzeuge for expert guidance and immediate availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CCMT09T308-MP4-WPP20G-WALTER Designation: CCMT09T308-MP4 WPP20G Facts Shape: Rhombus 80° Size: 09 Thickness: T3 Clearance angle: 7° Corner radius: 0.8 Special features Grade: WPP20G (Tiger·tec Gold) Chipbreaker: MP4 Application: Steel (ISO P) Tolerance class: M Series: Tiger-tec Gold FAQ What materials is this insert designed for? The CCMT09T308-MP4 WPP20G insert is designed for ISO P materials, specifically unalloyed and alloyed steel, where the WPP20G grade and Tiger·tec Gold coating provide reliable performance. Which chipbreaker should be used for reliable chip control? This insert uses the MP4 chipbreaker, which is integrated to produce controlled chips during turning operations in steels and helps maintain a clean cutting zone. Is the geometry suitable for shoulder and finishing cuts? The Rhombic 80° profile with a 0.8 mm corner radius and 7° clearance provides sufficient strength for shoulder cuts and can deliver good surface quality in finishing operations when paired with correct feeds and speeds. How does the Tiger·tec Gold technology benefit production? Tiger·tec Gold coating on the WPP20G grade enhances wear resistance and thermal stability, supporting longer tool life and more consistent results in repetitive turning cycles. What tolerance class is supplied and why does it matter? The insert is supplied in tolerance class M, which aids interchangeability and repeatable seating in compatible toolholders, reducing setup variation and supporting process reliability. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CCMT09T308-MP6 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold wear resistance, a proven MP6 chipbreaker and a compact rhombic geometry to secure consistent turning results in steel; order the inserts via Metav Werkzeuge or consult the technical team for cutting data and application advice. CCMT09T308-MP6 WPP10G Drehwendeschneidplatte (for steel) – Walter Tools, Tiger‑tec Gold CCMT09T308-MP6 WPP10G is a coated rhombic 80° indexable insert intended for general-purpose turning of steel, offering a balance of wear resistance and reliable chip control Tiger‑tec Gold coating for enhanced wear resistance Optimised MP6 chipbreaker for reliable chip control Rhombic 80° insert with 0.8 mm corner radius Suited for steel machining (ISO group P) Longer tool life through advanced coating technology The Tiger‑tec Gold series combines a wear‑resistant coating with a precisely graded substrate to extend productive service life. The WPP10G grade is a coated carbide designed for steel machining (ISO group P), which optimises performance under the typical heat and chip formation encountered during turning operations. By favouring controlled flank wear over catastrophic failure, the technology helps reduce tool changes and maintain consistent component quality. The result is measurable process stability and fewer production interruptions, supporting higher throughput in batch or continuous turning tasks. Predictable chip formation and stable cutting behaviour Chip control is a decisive factor for productivity; the MP6 chipbreaker is tuned to produce short, manageable chips when cutting a wide range of steels. The combination of the chipbreaker geometry and the insert’s medium tolerance class (M) ensures repeatable seating and consistent cutting line‑up in multi‑edge toolholders. That predictability translates into shorter setup times and reduced risk of surface damage from uncontrolled chips. With the 0.8 mm corner radius and a 7° clearance angle, the geometry provides a compromise between edge strength and the ability to achieve good surface finish on general turning operations. Application guidance: geometry and material match for efficient turning The rhombic 80° shape of the insert and its compact format (size 09, thickness T3) make it a versatile choice for external and light profiling tasks where access and chip evacuation are considerations. The small free angle supports stable cutting when facing and longitudinal turning of common unalloyed and alloyed steels. As a logical next step, pairing the insert with a rigid toolholder and appropriate coolant strategy will help leverage the Tiger‑tec Gold benefits for consistent component tolerances and surface quality. For customers seeking machining parameter suggestions or variant recommendations, technical consultation is available to align insert choice with specific workpiece materials and production aims. Contact Metav Werkzeuge for tailored application support and specify CCMT09T308-MP6 WPP10G inserts to optimise turning processes; email info@metav-werkzeuge.com or call +49 2822 7131930 for detailed cutting data and availability Technical data Article number: CCMT09T308-MP6-WPP10G-WALTER Label: Drehwendeschneidplatte CCMT09T308-MP6 WPP10G Manufacturer: Walter Tools Series: Tiger‑tec Gold Facts Free angle: 7° Corner radius: 0.8 mm Insert size: 09 Thickness: T3 Tolerance class: M Material group: P (steel) Special features Grade: WPP10G Chipbreaker: MP6 Plate form: Rhombus 80° Suitable for: Steel (ISO group P) Series description: Coated cemented carbide for steel machining FAQ What materials is this insert suitable for? The CCMT09T308-MP6 WPP10G insert is designed primarily for machining steel (ISO group P) and the WPP10G grade is optimised for typical heat and chip formation when turning unalloyed and alloyed steels. How does the MP6 chipbreaker affect machining? The MP6 chipbreaker delivers controlled, short chips and enhances process reliability; in combination with the Tiger‑tec Gold grade it supports predictable cutting behaviour and easier chip evacuation. What does the 0.8 mm corner radius mean for surface finish? A 0.8 mm corner radius offers a compromise between edge strength and surface integrity, enabling good finishing results on general turning while maintaining edge life under moderate cutting forces. Is this insert suitable for heavy roughing or fine finishing? The rhombic 80° geometry and the WPP10G grade make the insert suitable for general turning and light profiling; for heavy roughing or high‑precision finishing, toolholder and cutting parameter adjustments are recommended. Can the insert be used in standard CCMT toolholders? Yes, the CCMT09T308-MP6 format matches standard CCMT indexable insert holders; the medium tolerance class (M) supports consistent seating and repeatable clamping. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany. Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original factory‑new goods of the manufacturer.
CCMT09T308-MP6 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating, predictable chip control and a geometry optimised for steel turning to increase process reliability and reduce rework; order the CCMT09T308-MP6 WPP20G directly via Metav Werkzeuge or consult our technical team for application-specific recommendations. CCMT09T308-MP6 WPP20G turning insert for steel, Tiger·tec Gold — Walter Tools The CCMT09T308-MP6 WPP20G is an indexable rhombic 80° insert designed for robust steel turning and reliable surface quality in general and semi-finishing applications. Tiger·tec Gold coating WPP20G Designed for steel (ISO group P) MP6 chipbreaker for predictable chips Rhombic 80° CCMT, 0.8 mm corner radius High-performance steel machining with predictable chip flow The coated carbide grade WPP20G, part of the Tiger·tec Gold series, is formulated for the thermal and mechanical demands of steel machining and offers a balanced mix of wear resistance and toughness. The MP6 chipbreaker promotes controlled chip formation at typical cutting parameters for steel, reducing the risk of built-up edge and improving process stability. With a clearance angle of 7° and a compact profile, the insert supports efficient heat dissipation and consistent cutting forces, which translates directly into fewer interruptions and more productive machining cycles. Consistent surface finish and repeatable production results The rhombic 80° CCMT geometry combined with a 0.8 mm corner radius provides a secure edge for both finishing and light roughing, delivering repeatable surface quality part to part. The tolerance class M and plate thickness T3 ensure dimensional reliability when mounted in standard CCMT seats, making it simpler to maintain tight process windows. Favourable geometry and the coated top layer help to extend edge life, so workshops benefit from reduced dressing frequency and more predictable tool-change intervals. Straightforward integration and economical tool use Sized as an industry-standard CCMT09 insert, the part integrates into common holders and indexable tool systems, enabling quick replacement and multiple usable cutting edges per insert. The overall design reduces tool-change downtime and supports batch production where stability and low variance are key. For operations targeting a broad range of steels, the combination of Tiger·tec Gold grade and the MP6 breaker yields a cost-effective solution that keeps cycle times stable while preserving surface integrity. For specific holder compatibility or to optimally match cutting data, Metav Werkzeuge provides selection assistance and technical advice. Contact Metav Werkzeuge to specify Walter Tools Tiger·tec Gold inserts and to discuss the optimal CCMT setup for efficient steel turning and stable production results Technical Data SKU: CCMT09T308-MP6-WPP20G-WALTER Label: Drehwendeschneidplatte CCMT09T308-MP6 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte (indexable turning insert) Series: Tiger·tec Gold Grade: WPP20G Chipbreaker: MP6 Shape: Rhombus 80° Size: 09 Corner radius: 0,8 Clearance angle: 7° Thickness: T3 Tolerance class: M Material group: P (steel) Designation: CCMT09T308-MP6 WPP20G Facts Corner radius: 0.8 mm Clearance angle: 7° Size designation: 09 Thickness code: T3 Tolerance class: M Special features Tiger·tec Gold coating technology WPP20G coated carbide grade MP6 chipbreaker for steel Rhombic 80° CCMT form Suitable for machining steel (ISO group P) Indexable insert for standard CCMT holders Designed for reliable chip control and process stability FAQ What materials is this insert best suited for? The CCMT09T308-MP6 WPP20G by Walter Tools is optimised for steel (ISO group P), designed to handle the heat and chip characteristics typical of unalloyed and alloyed steels. How does the MP6 chipbreaker affect machining? The MP6 chipbreaker on the CCMT09T308-MP6 WPP20G promotes controlled chip formation, improving process stability and reducing the likelihood of built-up edge during steel turning. What does the CCMT09T308 designation indicate? CCMT denotes the rhombic 80° insert shape with a specific geometry; 09 indicates the nominal insert size, and T308 refers to thickness and nose radius geometry encoded in the designation used for toolholder compatibility. Can this insert be used for finishing operations? Yes, with its 0.8 mm corner radius and balanced Tiger·tec Gold grade, the insert is suitable for finishing and light semi-finishing where consistent surface quality is required. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. The mention of brand names such as Walter Tools serves explanatory purposes only and does not imply any affiliation with our company. The offered item is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com