32mm Combination Adapter Holder With 16mm Clamping, DIN 69871 Form AD/B - TECWERK
Benefit from a precise SK40 interface, a hardened and ground finish, and a 16 mm clamping bore that together deliver consistent concentricity and long tool life; order through Metav Werkzeuge or consult their specialists for application checks and compatibility advice. Combination mounting milling arbor DIN 69871 AD/B – SK40, clamping Ø 16 mm (TECWERK) The Combination mounting milling arbor is a DIN 69871 Form AD/B adapter designed for secure mounting of milling cutters with longitudinal or transverse keys in SK40 spindles for general machining and production environments Steep taper to DIN 69871 AD/B Hardened and ground for wear resistance Clamping bore 16 mm for cutter shanks A-length 55 mm for reliable axial support Precision interface for repeatable machining results The steep taper DIN 69871 Form AD/B provides a rigid, repeatable connection between spindle and toolholder that reduces runout and vibration during milling. The adapter's 16 mm clamping bore is intended for cutters with longitudinal or transverse keys, ensuring secure axial and radial placement of the shank. By using a standardised taper and a ground seating surface, the assembly improves repeatability across setups, which translates into fewer scrap parts and less rework on the shop floor. Built for durability and low maintenance in production Manufactured case-hardened and ground, this arbor resists wear at the seating and clamping zones, extending service intervals and maintaining concentricity over prolonged use. The hardened surface counters micro-movement under load, while the ground finish aids precise alignment with the spindle taper. For continuous or batch machining, this means a more stable cutting process and predictable tool life, supporting leaner production planning and reduced downtime. Compatibility, mounting and practical benefits explained The adapter is suitable for use with SK40 spindles and accepts milling cutters fitted with a longitudinal or transverse key. The specified A-length of 55 mm provides adequate axial support for most standard cutter shanks while keeping the tool projection manageable for accurate machining. Mounting is performed by seating the taper and securing the cutter in the clamping bore; if concentricity or runout is critical, a simple dial-indicator check after assembly confirms correct positioning. This approach delivers an efficient balance of rigidity and accessibility for tool changes. For tailored application advice on the TECWERK DIN 69871 AD/B arbor or to confirm compatibility with specific cutter shanks, contact Metav Werkzeuge in Emmerich for direct support and fast supply. Technical Data Article number: 2000833795NW Product type: Combination mounting milling arbor Standard: DIN 69871 Form AD/B Facts Diameter D: 32 mm Clamping bore d: 16 mm A-length: 55 mm Additional length L: 17 mm Packaging unit: 1 Special features Steep taper to DIN 69871 Form AD/B For milling cutters with longitudinal or transverse key Case-hardened and ground Manufacturer: TECWERK FAQ What spindle standard does this arbor fit? The arbor conforms to DIN 69871 Form AD/B and is intended for use in SK40 spindles, providing a standardised, repeatable interface. Which cutter shank types are supported? The arbor accepts milling cutters with a longitudinal or transverse key and a clamping bore of 16 mm, ensuring secure axial locking of keyed shanks. How is concentricity checked after mounting? After seating the taper and clamping the cutter, a dial indicator on the cutter periphery is the recommended method to verify concentricity and runout. Is the arbor suitable for heavy-duty milling cycles? The case-hardened and ground construction increases wear resistance and stability, making the arbor appropriate for standard industrial milling tasks where a robust toolholder is required. Can the arbor be re-ground or refurbished when worn? Surface wear on the seating faces can be assessed by a tooling specialist; refurbishment depends on condition and must preserve the original taper geometry for safe use. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm Combination Milling Arbor With 16mm Clamping Diameter, DIN 69871 AD/B - TECWERK
Take advantage of a robust interface with a DIN 69871 steep taper and a compact 16 mm clamping diameter for reliable milling setups; the case‑hardened, ground body and 100 mm projection minimise downtime and ensure repeatable precision. Order the combination milling arbor directly via Metav Werkzeuge or request advice from their consultants for application matching and delivery. Combination milling arbor DIN 69871 AD/B – SK40, 16 mm clamping (TECWERK) The Combination milling arbor for SK40 machines, designed to accept milling cutters with longitudinal or transverse keyways and to deliver stable tool guidance in general workshop and industrial milling applications. Steep taper DIN 69871 Form AD/B 16 mm clamping diameter Case-hardened and ground Suitable for keyway milling cutters Consistent, repeatable seating for high-precision milling The steep taper DIN 69871 interface provides a precise seating that transfers torque evenly and reduces runout, which leads to improved surface finish and tool life. The SK40 taper connection is a widely used machine interface, so the arbor offers straightforward interchangeability within existing toolholders. By combining a standardised taper with a narrow 16 mm clamping diameter, this arbor enables compact setups where accurate concentricity is essential for serial production and fine machining work. Hardening and finishing that reduce maintenance intervals The shank and critical contact surfaces are case‑hardened and ground to resist wear from repeated tool changes and cutting forces, so frequency of regrinding or replacement is reduced. The precision finish supports stable clamping and minimises fretting at the taper junction. With an outer diameter of 32 mm and a projection of 100 mm, the component balances rigidity and accessibility for typical milling operations, lowering the risk of vibration and the associated quality loss. Secure clamping for longitudinal and transverse keyways Designed specifically to accept milling cutters with either longitudinal or transverse keyways, the arbor ensures positive drive and axial location of the tool. The 16 mm clamping diameter mates with common keyed tool shanks, providing a reliable mechanical lock that prevents slippage under heavy cuts. This configuration is especially useful when machining operations require repeatable indexing or when cutters must be removed and replaced frequently without losing positional accuracy. Standards-based design for smooth integration into production Conformance to DIN 69871 Form AD/B means the arbor fits established tooling systems and supports predictable set‑up times on the shop floor. The combination of a standard SK40 interface, defined projection length and measured diameters helps planners and operators achieve consistent tool offsets and programming parameters in CNC environments. Clear technical conformity reduces set‑up variance and contributes to a more efficient production workflow with fewer rejects. Contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to discuss the TECWERK combination milling arbor with DIN 69871 taper and 16 mm clamping diameter and to arrange supply from stock in Emmerich. Technical data Article number: 2000833796NW Type: Combination milling arbor (Kombi Aufsteckfräsdorn) Brand: TECWERK Standard: DIN 69871 Form AD/B Facts Clamping diameter d: 16 mm Outer diameter D: 32 mm Projection A: 100 mm Length L: 17 mm Special features Steep taper according to DIN 69871 Form AD/B Case-hardened and ground Accepts milling cutters with longitudinal or transverse keyway SK40 taper interface FAQ What taper standard does this arbor use? The combination milling arbor complies with DIN 69871 Form AD/B, providing a steep taper interface for SK40 spindles. Which cutter shank types are accepted? This arbor accepts milling cutters with longitudinal or transverse keyways, secured by a 16 mm clamping diameter for positive drive. What are the key dimensions to consider for set-up? Relevant dimensions include an outer diameter of 32 mm, a projection (A) of 100 mm and a clamping diameter of 16 mm; the article number is 2000833796NW for ordering. How does the surface treatment affect service life? The case‑hardened and ground finish increases wear resistance at contact zones, improving longevity and reducing maintenance cycles for the arbor. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
32mm Drive Ring For 16mm Arbor, For Keyed Slot Milling Cutters, DIN 6366 - TECWERK
Take advantage of the standardised fit and compact design to ensure reliable torque transmission and simple integration into existing arbor systems; order the part directly via Metav Werkzeuge or contact their consultants for clarification on compatibility and supply. TECWERK drive collar 32 mm (for 16 mm arbors) – DIN 6366 The TECWERK drive collar 32 mm is a compact drive component, compliant with DIN 6366, engineered to transfer torque to mounted cutters with a transverse groove and to fit 16 mm arbor shanks. DIN 6366 compliance for standardised fit Designed for mounted cutters with transverse groove Compatible with 16 mm arbor shanks Outer diameter 32 mm for secure engagement Reliable torque transfer for mounted cutters The drive collar delivers consistent mechanical engagement between the arbor and mounted cutters, ensuring dependable transmission of rotational force. By engaging the cutter’s transverse groove, the component reduces the risk of slippage under load, which supports uninterrupted machining cycles. Compliance with DIN 6366 guarantees interchangeability with other standardised components, simplifying maintenance planning and spare-part management for small workshops and production facilities alike. Standardised geometry for straightforward integration With its compact geometry, the component is designed to sit precisely on a 16 mm arbor shank and engage mounted cutters with transverse grooves. The standardised design allows fast replacement and predictable alignment, which reduces setup time during cutter changes. For operators less familiar with technical specifications, the collar can be understood as a simple mechanical interface: it locks into a groove on the cutter and the arbor, converting the spindle’s rotation into usable cutting torque without additional adapters. Practical workshop benefits and trusted supply In routine workshop use, the collar’s straightforward function supports reliable machining of profiles and edges when used with compatible mounted cutters. The compact outer diameter provides secure engagement while keeping the assembly small and easy to handle, which is particularly useful where space on the arbor is limited. Supplied as a single unit, the part helps maintain a minimal inventory strategy when paired with other standardised components from a single supplier, reducing administrative overhead and complexity. Choose the TECWERK drive collar for standardised, reliable torque transfer and contact Metav Werkzeuge for technical guidance or procurement from their Emmerich centre Technical data Article number: 2000834086NW Product: Drive collar (Mitnehmerring) Brand: TECWERK Packaging unit: 1 Description: to transfer mounted cutters with transverse groove, compliant with DIN 6366, for use on mounted cutter arbors Dimensions / Core data Outer diameter: 32 mm Arbor fit diameter: 16 mm a dimension: 10 mm b dimension: 8 mm h dimension: 5 mm Applications / Special features Standard: DIN 6366 Intended for mounted cutters with transverse groove Fits mounted cutter arbors (Aufsteckfräserdorne) Compact, standardised design for easy replacement FAQ What is the primary application of this drive collar? The drive collar is intended for torque transfer to mounted cutters with a transverse groove; the TECWERK drive collar 32 mm secures engagement between cutter and 16 mm arbor shank. Which arbor diameter does the collar fit? The collar is designed to fit a 16 mm arbor shank, providing a standardised connection for compatible mounted cutters. Is this component compatible with industry standards? Yes, the part conforms to DIN 6366, ensuring compatibility with other standardised fittings and reducing the need for custom adapters. How is the item identified for ordering or stock management? The item is listed under article number 2000834086NW (SKU 2000834086NW) and described as a TECWERK drive collar for mounted cutters. Can the collar be used in compact setups with limited arbor space? The compact outer diameter of 32 mm and low-profile dimensions make the collar suitable for installations where space on the arbor is restricted. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm E2 Toolholder For Boring Bars With Internal And External Coolant, DIN 69880 - TECWERK
Combine durable DIN 69880 compatibility with VDI30 clamping and internal/external coolant routing for reliable drilling-bar performance; order the toolholder directly via Metav Werkzeuge or consult our specialists for application advice. Toolholder for drilling bars E2 — DIN 69880, VDI30, 32 mm clamping (TECWERK) The Toolholder for drilling bars E2 secures VDI30-mounted drilling bars with a standardised DIN 69880 interface and provides both internal and external coolant routing for machining operations in toolrooms and industrial workshops DIN 69880 standardised interface VDI30 clamping with 32 mm diameter Internal and external coolant supply No shortening of drilling bar required Faster set-ups through standardised interface and robust clamping The holder is built to the DIN 69880 standard and accepts VDI30 tooling, delivering consistent axial alignment and repeatable concentricity. With a 32 mm clamping diameter and a cylindrical shank, fixture time is reduced and spindle compatibility is straightforward. This engineered fit translates into fewer measurement checks between operations and more predictable process outcomes, supporting efficient production planning and shorter machine downtime. Coolant support that stabilises tool life and surface quality Equipped for both internal coolant and external coolant supply, the design maintains chip evacuation and cooling at the cutting zone, which helps to preserve edge integrity and improve surface finish. The holder’s coolant routing contributes to thermal stability during longer cycles; combined with proper tooling, this can extend component life and lower tool-change frequency. The result is a machining set-up that sustains performance under varied cutting conditions. Practical workshop benefits: no reworking of bars and broad compatibility The E2 configuration eliminates the need for shortening the drilling bar prior to assembly, enabling immediate use of standard-length bars and saving preparatory labour. Compatibility with drilling bars and the VDI30 interface ensures flexibility across jobs and simple spare-part management. The construction emphasises rigidity and alignment, which supports precision drilling and reliable repeatability across series production. For ordering information or application-specific recommendations on the TECWERK E2 toolholder, contact Metav Werkzeuge in Emmerich—our specialists can advise on spindle compatibility and machining set-ups to ensure optimal results. Technical data Article number: 2000833677NW Manufacturer: TECWERK Product type: Toolholder for drilling bars Form: E2 Packaging unit: 1 Dimensions / measurable data Clamping diameter d2: 32 mm d1: 30 mm d6: 68 mm d8: 67 mm l6: 75 mm l3: 22 mm h1: 28 mm h2: 30 mm Standard: DIN 69880 Special features Internal and external coolant supply Cylindrical shank Suitable for drilling bars VDI30 interface Not through-bored No shortening of drilling bar necessary FAQ What spindle taper does the holder match? The holder uses a VDI30 interface and is manufactured to the DIN 69880 standard, so it is intended for machines and turrets that accept VDI30 toolholders. Is the coolant routed through the toolholder? The TECWERK E2 toolholder is specified with internal and external coolant supply, supporting coolant delivery to the tool zone for improved chip control and cooling. What clamping size is required for compatible drilling bars? Drilling bars with a 32 mm diameter match the clamping diameter (d2: 32 mm) specified for this toolholder. Does the holder require the drilling bar to be shortened before assembly? No shortening of the drilling bar is required for use with the TECWERK E2 toolholder; it is designed for immediate assembly with standard bars. What are the key dimensional references to check before ordering? Refer to the measurable data: d2 32 mm, d1 30 mm, l6 75 mm and the DIN 69880 specification to confirm compatibility with the machine and tooling system. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm ER Collet Chuck 1–10mm Clamping Range Cylindrical Shank 150mm - TECWERK
Take advantage of a compact and reliable clamping solution that combines an ER16 interface with a 1–10 mm clamping range for efficient tool holding; the cylindrical shank and lateral clamping face deliver secure mounting and consistent concentricity. Order the chuck directly via Metav Werkzeuge or ask our consultants for application advice. ER collet chuck — TECWERK, ER16 interface, 1–10 mm clamping range The ER collet chuck is a compact tool-holder designed for secure clamping of cylindrical-shank tooling in standard ER collets, suited to general workshop and light industrial milling where repeatable tool retention and quick changeover are required ER16 interface for standard ER collets Clamping range 1–10 mm for versatile tooling Cylindrical shank with lateral clamping face 32 mm body diameter, robust construction Reliable clamping performance that reduces setup time The combination of an ER16 interface and a 1–10 mm clamping range provides compatibility with a broad set of standard ER collets, enabling fast tool changes and fewer holder variants in stock. The design follows established collet standards, delivering predictable clamping force and repeatability; this reduces time spent on re‑setting and minimises idle machine time. For operations where cycle time and tool retention matter, the precise clamping behaviour translates directly into improved throughput and lower setup overhead. Robust design for concentricity and secure tool holding A cylindrical shank combined with a lateral clamping face produces a compact, axially stable connection between spindle adapter and tool holder. The 32 mm body diameter and a 16 mm shank diameter provide a sturdy interface that resists deflection under normal cutting loads, supporting consistent concentricity and surface finish. The holder accepts cylindrical-shank tooling in ER collets to DIN 6499, so standard collets and accessories can be used without modification; maintenance is limited to routine cleaning and light lubrication to preserve service life. Practical use cases and supply confidence for the workshop Ideal for general milling, drilling and reaming where standard cylindrical-shank tools are used, the holder suits small-batch production and versatile workshop setups. Sourcing via Metav Werkzeuge ensures a quality-controlled supply chain: Metav’s Emmerich location acts as a quality filter for the European market and supports reliable delivery and technical guidance. The compact holder design helps reduce inventory complexity while maintaining the tool control required for repeatable production results. Contact Metav Werkzeuge for a technical consultation and to secure this TECWERK ER collet chuck (SKU 2120620189NW); email info@metav-werkzeuge.com or call +49 2822 7131930 for precise specification support Technical data Article number: 2120620189NW Product type: ER collet chuck Brand: TECWERK Interface: ER16 Packing unit: 1 Facts Clamping range: 1–10 mm Body diameter: 32 mm Shank diameter: 16 mm Special features Cylindrical shank design Lateral clamping face For clamping cylindrical-shank tools in ER collets to DIN 6499 FAQ What collet sizes does this holder accept? The holder accepts ER collets operating within a 1–10 mm clamping range; standard ER collets to DIN 6499 are compatible. Which interface does the chuck use? The chuck is furnished with an ER16 interface and is designed for use with corresponding ER16 collets. Is the holder suitable for light production and workshop use? Yes, the compact design and robust cylindrical shank make the holder suitable for workshop environments and light industrial production where repeatable clamping is required. How should the chuck be maintained? Routine maintenance involves cleaning the clamping bore and collets, removing swarf, and applying light lubrication to moving parts to ensure lasting performance. What is the SKU for ordering and reference? The product is listed under SKU 2120620189NW for ordering and technical reference. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm ER Collet Chuck DIN 69871 Form AD 1-10mm Clamping Range, SK40 A.63mm - TECWERK
Benefit from a precision-engineered clamping solution that combines DIN 69871 Form AD compliance, a 1–10 mm clamping range and the robustness of an SK40 taper for consistent tool retention; order through Metav Werkzeuge or consult the Metav team for application advice. TECWERK ER collet chuck SK40 (DIN 69871 Form AD) — ER collet chuck with 1–10 mm clamping range and A = 63 mm TECWERK ER collet chuck SK40 (DIN 69871 Form AD) is designed for secure clamping of cylindrical-shank tools in machining spindles and toolholders that conform to DIN 6499. DIN 69871 Form AD compatibility Clamping range 1–10 mm SK40 taper, A = 63 mm Diameter D = 32 mm Secure clamping for cylindrical-shank tools and repeatable results The ER collet chuck delivers precise axial and radial retention for tools with cylindrical shanks, ensuring repeatability and stable machining results. Compliance with DIN 69871 Form AD guarantees interchangeability with standard spindle noses and tooling systems, so setup variability is reduced. The specified 1–10 mm clamping range accommodates common cutter shank diameters, reducing the need for frequent toolholder changes and helping to maintain consistent concentricity during milling and drilling operations. Standard conformity for straightforward integration and tool change Adherence to the DIN 69871 standard means the chuck mates reliably with spindles specified for Form AD dimensions, simplifying integration into existing rigs. The SK40 taper and A = 63 mm projection provide a predictable tool geometry for programming and fixture design. Where tools conform to DIN 6499, the ER collet system ensures firm clamping without additional adapters, supporting faster changeovers and lower setup time in serial production and maintenance workshops. Productivity gains through robust design and minimal maintenance A robust clamping interface and standardised taper reduce vibration and tool run-out, which directly improves surface finish and tool life—two tangible productivity benefits. The construction supports frequent tool changes while preserving accuracy, so throughput increases without sacrificing quality. Routine upkeep is straightforward: inspection of the collet and nut assembly for wear and correct seating keeps the system performing within expected tolerances, extending service intervals and lowering total cost of ownership. Compatibility, workshop versatility and application scope The chuck suits a wide range of general workshop and industrial machining tasks where cylindrical-shank tooling is used. With a clear D = 32 mm body diameter and ER system compatibility, the holder fits common ER collets and accessories sized for the ER16 designation of the Aufnahme. This flexibility allows consolidation of tooling inventory and supports efficient tooling management across milling centres and toolroom machines, while ensuring that clamping integrity is maintained on both short and extended-reach tool applications. Contact Metav Werkzeuge for tailored advice on TECWERK SK40 ER collet chucks and application matching — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 2000833705NW Norm: DIN 69871 Form AD Product type: ER collet chuck Facts Clamping range: 1–10 mm Diameter D: 32 mm A (projection): 63 mm Taper: SK40 Special features Aufnahme: ER 16 / 426 E For clamping of cylindrical-shank tools to DIN 6499 Packaging unit: 1 FAQ What shank diameters are suitable for this collet chuck? The TECWERK ER collet chuck supports shank diameters from 1–10 mm, covering common small-to-medium cutter and drill shanks. Is the holder compatible with standard SK40 spindles? Yes, the chuck is manufactured to DIN 69871 Form AD dimensions and is compatible with SK40 spindle noses designed to that form. Which ER collet size does the Aufnahme accept? The Aufnahme is specified as ER 16 / 426 E, indicating compatibility with ER16 collets matched to the 1–10 mm clamping range. How does DIN 69871 conformity benefit workshop operations? Conformity to DIN 69871 ensures mechanical interchangeability and predictable tool projection (A = 63 mm), which simplifies setup, reduces errors and supports consistent machining outcomes with the TECWERK ER collet chuck. What routine checks preserve performance of the chuck? Regular inspection for collet and nut wear, correct seating and cleanliness of the taper and collet bore helps maintain repeatability and prolongs service life of the tool holder. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm ER Collet Chuck HSK-A63 1-10mm Clamping Range, DIN 69893 Form A - TECWERK
Take advantage of a compact HSK-A63 interface combined with the ER collet system and a 1–10 mm clamping range to ensure reliable tool retention and repeatable runout control; suitable for cylindrical shank tools with a 100 mm projection. Order directly via Metav Werkzeuge or consult their advisors for application-specific integration advice. ER collet chuck DIN 69893 Form A HSK-A63 — ER16, 1–10 mm clamping range (TECWERK) The ER collet chuck DIN 69893 Form A HSK-A63 is a precision toolholder designed for secure clamping of cylindrical shank tools in machining centres and high-precision workshops. HSK-A63 interface, DIN 69893 Form A ER16 collet system, 1–10 mm range 100 mm projection for deep tool reach Compatible with collets to DIN 6499 Faster setup and consistent tool retention The compact hollow-shank taper specified by DIN 69893 Form A enables rapid, repeatable connections between spindle and toolholder; this reduces downtime during tool changes and supports consistent concentricity. The ER16 collet arrangement covers a 1–10 mm clamping range, so common cylindrical shank tools are retained without frequent collet swaps. In practice, the standard interface and collet system mean shorter setup times and fewer adjustment cycles, which improves overall process reliability in batch and serial production. Engineered for rigidity and precise concentricity Rigid contact is achieved through the HSK-A63 taper and the ER collet mechanism, which together provide a secure axial and radial hold. Concentric accuracy is essential for finishing operations; the design limits runout and transmits spindle torque efficiently. Where high positional accuracy is required, the combination of hollow shank taper and collet grip ensures that the clamped tool is held with minimum deflection, making the assembly well suited to precision milling, reaming and drilling tasks that depend on repeatable tool position. Broad compatibility with cylindrical shank tooling The toolholder is intended for use with cylindrical-shank tools accommodated by collets to DIN 6499, offering straightforward integration into existing setups that use ER collets. With an outer diameter dimension of 32 mm and a projection length A = 100 mm, the chuck supports operations where extended reach is required while maintaining stability. The straightforward interface means the holder can be adopted across different machines equipped with HSK-A spindles that accept Form A tapers. Practical inspection and workshop handling Maintenance is kept simple: the hollow-shank taper can be inspected visually and cleaned to maintain contact integrity, and ER collets are replaceable to restore clamping precision if wear occurs. Routine checks of the taper face and collet condition help preserve concentricity and prolong service life. The unit is supplied ready to fit into a compatible HSK-A spindle and requires standard workshop tools for collet changes, keeping upkeep straightforward for maintenance teams and machinists. For tailored application advice and to confirm compatibility with existing spindles and tooling, contact Metav Werkzeuge for expert guidance and swift supply of the matching ER collet chuck and accessories Technical data SKU: 2000833827NW Item label: ER collet chuck DIN 69893 Form A HSK-A63 ER16 1–10 mm 100 mm TECWERK Manufacturer: TECWERK UID: 2000833827NW Core specifications Standard: DIN 69893 Form A Interface: HSK-A / ER16 / 426 E Clamping range: 1–10 mm Outer diameter: 32 mm Length A: 100 mm Special features Hollow-shank taper, Form A For clamping cylindrical shank tools to DIN 6499 ER collet system (ER16) Packaging unit: 1 FAQ What clamping range does this collet chuck cover? The TECWERK ER collet chuck (ER collet chuck DIN 69893 Form A HSK-A63, SKU 2000833827NW) covers a 1–10 mm clamping range using ER16 collets. Is the holder compatible with standard HSK-A63 spindles? Yes, the holder is specified for HSK-A63 interfaces (DIN 69893 Form A) and is intended to mate with spindles engineered to that standard. Can long tools be used with this chuck without loss of stability? With a projection length A = 100 mm and an outer diameter of 32 mm, the toolholder gives extended reach; however, tool overhang and specific machining forces should be evaluated to ensure required rigidity. Which collets are required for operation? ER16 collets to DIN 6499 are used with this chuck; selecting the correct collet size within the 1–10 mm range ensures optimal clamping and concentricity. How should the taper and collets be maintained to preserve precision? Routine cleaning of the taper face and inspection or replacement of worn ER collets is recommended to maintain concentricity and clamping reliability for the TECWERK ER collet chuck. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm ER Collet Nut With Eccentric Ring M22 x 1.5, Balanced DIN 6499 - TECWERK
The robust combination of a balanced design, standard M22 x 1.5 thread and an eccentric ring guarantees secure, repeatable clamping for ER 16 systems; order directly via Metav Werkzeuge or consult the technical team for compatibility advice. TECWERK ER 16 Collet Nut with Eccentric Ring — 32 mm, M22 x 1.5 The TECWERK ER 16 Collet Nut (32 mm) is a standard-design locking nut with an eccentric ring, engineered for secure clamping in ER 16 collet chucks and compliant with DIN 6499. *Standard design with eccentric ring *Conforms to DIN 6499, balanced execution *Thread M22 x 1.5 for ER 16 collet chucks *Diameter 32 mm for secure clamping Improved machining reliability through balanced clamping A balanced clamping solution reduces spindle vibration and contributes to consistent runout, improving part quality and tool life. The TECWERK ER 16 Collet Nut is produced as a balanced execution in accordance with recognised standards, ensuring that the chuck assembly maintains stability at higher speeds. This stability translates into fewer scrap parts and longer intervals between rework, supporting cost-effective, continuous production. Straightforward compatibility with ER 16 systems Matching the standard thread and size simplifies integration into existing tooling. The nut’s M22 x 1.5 thread and 32 mm diameter make it directly compatible with ER 16 collet chucks, allowing straightforward replacement or spare-parts stocking. For workshops and production lines that rely on standardised components, this compatibility reduces setup time and minimises inventory complexity while keeping clamping performance predictable. Practical benefits of the eccentric ring in everyday use The built-in eccentric ring improves centring and clamping consistency without adding complexity to the setup process. In practical terms, the eccentric element helps compensate for minor irregularities in collet seating, resulting in a more uniform grip on the tool shank. This leads to reduced micro-movement during cutting, a calmer spindle during operation and a measurable improvement in surface finish and dimensional accuracy for precision tasks. Durable standard construction for reliable service life Manufactured to a standard industrial specification, the nut offers dependable mechanical properties for routine workshop conditions. The standard design provides a robust interface between collet and chuck body, ensuring repeatable performance under normal machining loads. By choosing a proven, standard part, procurement teams benefit from predictability in maintenance cycles and straightforward interchangeability across ER 16 tooling platforms. For secure and repeatable clamping in ER 16 setups, order the TECWERK ER 16 Collet Nut via Metav Werkzeuge for fast supply from Emmerich, or consult Metav’s experts for application-specific advice and compatibility checks. Technical data Article number: 2000833994NW Item: ER 16 collet nut with eccentric ring Execution: Standard design Packaging unit: 1 SKU / UID: 2000833994NW Facts Diameter: 32 mm Thread: M22 x 1.5 Suitable for: ER 16 Conforms to: DIN 6499 Special features Standard design with eccentric ring For ER collet chucks Balanced execution M22 x 1.5 thread D: 32 mm FAQ Is this nut compatible with all ER 16 collet chucks? Compatibility is intended for ER 16 systems; the TECWERK ER 16 Collet Nut fits ER 16 collet chucks that accept an M22 x 1.5 thread and a 32 mm diameter nut What standard does the nut conform to? The component is specified to meet DIN 6499, ensuring standardised dimensions and balanced performance suitable for ER 16 tooling Does the eccentric ring affect installation? The eccentric ring is integrated into the nut’s design to improve clamping consistency and does not require special installation beyond standard fitting procedures for collet nuts Can this nut be used at higher spindle speeds? The balanced execution supports stable operation at typical machining speeds for ER 16 systems; final speed limits depend on the complete chuck and spindle assembly Is the thread specification standardised for replacement parts? Yes, the M22 x 1.5 thread is a standard specification intended for direct interchangeability within ER 16 tooling platforms Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm Spannzangenfutter ER Spannbereich 1-10mm A 100mm, DIN 69871 Form AD - TECWERK
Spannzangenfutter ER DIN 69871 Form AD (SK40, A 100 mm) Das Spannzangenfutter ER DIN 69871 Form AD von TECWERK für präzise Werkzeugspannung in SK40-Aufnahmen Steilkegel nach DIN 69871 Form AD Kompatibel mit SK40 Aufnahmen Spannbereich 1-10 mm für Zylinderschaft Baulänge A 100 mm, Durchmesser 32 mm Hohe Präzision für den Produktionsalltag Das Spannzangenfutter wurde gezielt für die zuverlässige Aufnahme von Werkzeugen mit Zylinderschaft entwickelt und garantiert durch den Steilkegel DIN 69871 Form AD sichere Kraftübertragung. Die Spannbereich 1-10 mm erlaubt flexiblen Einsatz von feinen bis mittelgroßen Schaftdurchmessern, wodurch Rüstzeiten reduziert und Werkzeugwechsel beschleunigt werden. Anwender profitieren von konstanter Spannkraft, die Ausschuss minimiert und die Prozessstabilität erhöht. Kompatibilität und einfache Montage für Werkstatt und Produktion Dank der SK40-Aufnahme lässt sich das Futter direkt in gängige Maschinenspindeln integrieren. Die kompakte Bauform mit A 100 mm und Durchmesser 32 mm sorgt für gute Zugänglichkeit an Bearbeitungsstellen und reduziert Kollisionsrisiken. Das ER-System bietet hohen Rundlauf und einfache Handhabung beim Ein- und Ausspannen der Spannzange, was die Bedienung vereinfacht und Stillstandszeiten verringert. Anwendungsnutzen und Zielgruppe Konzipiert für Metallbearbeitung, Werkzeug- und Formenbau sowie Serienfertigung, eignet sich das Futter besonders für Betriebe, die flexible Werkzeugbestückung und kurze Umrüstzeiten benötigen. Betreiber von CNC-Fräsen und Bearbeitungszentren erreichen mit diesem System bessere Oberflächen und gleichbleibende Bauteilqualität. Die klare Normausführung macht die Auswahl und Dokumentation in Fertigungsprozessen einfacher und nachvollziehbar. Warum dieses System wählen Die Kombination aus bewährter Normausführung und universellem ER-System bietet ein hervorragendes Verhältnis von Wirtschaftlichkeit und Präzision. Für Entscheider bedeutet das kalkulierbare Prozesse, weniger Nacharbeit und verbesserte Fertigungsqualität. Wer auf standardisierte Schnittstellen setzt, kann Programme, Spannmittel und Werkzeuge über verschiedene Maschinen hinweg einfacher austauschen. Empfehlung: Für präzise, normgerechte Werkzeugspannung in SK40-Aufnahmen empfiehlt sich dieses Spannzangenfutter von TECWERK; bei Fragen zur Einsatzfähigkeit oder zur Integration in vorhandene Spindeln steht Metav persönlich zur Beratung zur Verfügung — eMail: info@metav-werkzeuge.com, Telefon: +49 2822 7131930 Produktmerkmale Artikelnummer: 2000833706NW Marke: TECWERK Produktart: Spannzangenfutter ER Norm: DIN 69871 Form AD Fakten Durchmesser: 32 mm Spannbereich: 1-10 mm A (Baulänge): 100 mm Verpackungseinheit: 1 Besonderheiten Aufnahme: ER 16 / 426 E 1 SK40: Aufnahmeschaft für Maschinenspindeln Steilkegel DIN 69871 Form AD: kegelige Aufnahme Norm ER: Spannzangensystem für flexible Schaftspannungen FAQ Wie groß ist der Spannbereich und für welche Schaftformen ist das Futter geeignet? Der Spannbereich beträgt 1-10 mm; das Spannzangenfutter ist ausgelegt für Zylinderschaft-Werkzeuge und Spannzangen nach DIN 6499. Ist das Spannzangenfutter mit SK40-Spindeln kompatibel? Ja, die Ausführung ist für SK40-Aufnahmen konzipiert und lässt sich direkt in entsprechende Maschinenspindeln einbauen. Welche Normen beschreibt das Produkt und warum ist das wichtig? Das Futter entspricht der DIN 69871 Form AD, eine Standard-Norm für kegelige Werkzeugaufnahmen, die Austauschbarkeit und Prozesssicherheit in der Fertigung gewährleistet. Für welche Maschinen und Anwender ist dieses Spannzangenfutter besonders geeignet? Hauptsächlich für CNC-Fräsen und Bearbeitungszentren in Werkstätten, Werkzeugbau und Serienfertigung, die normgerechte, schnelle Werkzeugwechsel benötigen. Welche Vorteile bringt das ER-System beim täglichen Einsatz? Das ER-System ermöglicht schnellen Werkzeugwechsel, guten Rundlauf und flexible Spannbereiche, wodurch Rüstzeiten sinken und Fertigungsqualität steigt. Hersteller: NORDWEST Handel AG; Robert-Schuman-Straße 17; 44263 Dortmund
32mm Tool Holder E1 For Indexable Drills With Internal Coolant, DIN 69880 - TECWERK
Benefit from precise VDI40 mounting, internal coolant capability and DIN 69880 conformity to ensure consistent clamping and reliable drilling cycles; order the tool holder directly via Metav Werkzeuge or ask our consultants if needed. Tool holder E1 DIN 69880 — VDI40 clamping Ø32 mm, TECWERK A Tool holder E1 DIN 69880 designed for indexable insert drills, offering a cylindrical shank and coolant-through capability for machining centres and lathes. VDI40 mounting for precise repeatability Conforms to DIN 69880 standard Internal coolant supply for chip evacuation Clamping diameter Ø32 mm, robust cylindrical shank Faster set-ups through standardised VDI40 mounting The VDI40 interface provides high repeatability and quick tool changes, reducing machine downtime and setup complexity. With adherence to DIN 69880, the holder guarantees dimensional compatibility across systems that use the same standard, so toolholders and adaptors fit consistently. This standardised connection translates into measurable time savings on serial production runs and simplifies tool inventory management in workshops and production cells. Coolant-through design that protects inserts and improves cycle stability The internal coolant supply directs lubricant and coolant to the cutting edge, improving chip evacuation and heat control during drilling operations. By maintaining a stable thermal environment at the cutting zone, the coolant-through feature helps to extend insert life and maintain hole quality over long cycles. For operations combining drilling and light turning, efficient coolant routing reduces the risk of built-up edge and minimises rework. Robust geometry for industrial use and vibration resistance The holder’s cylindrical shank and E1 form offer a compact, rigid connection suited to medium-duty machining tasks. The measured clamping diameter of Ø32 mm supports stable seating of indexable insert drills and reduces deflection under cutting forces, which benefits hole concentricity and surface finish. The construction is aimed at keeping vibrations low and ensuring repeatable results in batch production. Straightforward integration with indexable insert drills and tooling kits Designed specifically for indexable insert drills, the holder accepts standard insert drill cartridges and integrates with typical spindle setups that use VDI40. The compact l1 and l3 dimensions provide a predictable tool envelope for programming and collision avoidance. Workshops benefit from easier tool management and a consistent reference length when planning setups for automated or manual machining operations. For tailored advice on selecting the right VDI40 tool holder for specific drilling tasks or to order this TECWERK tool holder via Metav Werkzeuge, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 2000833669NW Brand: TECWERK Product type: Tool holder for indexable insert drills Form: E1 Standard: DIN 69880 Core data d2: 32 mm h1: 32.5 mm d1: 40 mm d3: 52 mm l3: 22 mm d6: 83 mm l1: 75 mm Special features For indexable insert drills With cylindrical shank Coolant-through for drilling and turning tools Conforms to DIN 69880 Packaging unit: 1 FAQ What interface does this tool holder use? The tool holder uses a VDI40 interface, ensuring standardised mounting and precise repeatability for indexable insert drilling applications. Is the tool holder suitable for coolant-through drilling? Yes, the holder is designed with internal coolant supply, enabling effective coolant routing to the cutting edge for improved chip evacuation and tool life. Which drill diameter does the holder accept? The clamping diameter is Ø32 mm, suitable for compatible indexable insert drill cartridges and tooling systems. Does the product comply with industry standards? The tool holder conforms to DIN 69880, providing predictable dimensions and compatibility across systems that follow the same standard. What is the article number for ordering? The SKU for ordering is 2000833669NW, listed for the TECWERK tool holder E1 designed for indexable insert drills. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm Tool Holder E2 For Boring Bars With Internal And External Coolant Supply, DIN 69880 - TECWERK
Data inconsistency detected: the product data lists both internal and external coolant supply and explicitly states not through-drilled, which is contradictory and prevents a reliable product description. This discrepancy creates confusion regarding the actual specifications of the product, making it difficult to determine its intended functionality or compatibility with specific applications. Accurate and consistent information is essential for ensuring that customers can make informed decisions and avoid potential issues during use. It is recommended that the manufacturer or responsible party review and clarify the product details to resolve this inconsistency and provide a clear, reliable description. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
34mm ER 25 Collet Clamping Diameter 5mm, Precision Runout 5 µm - TECWERK
Take advantage of the collet's precise runout and full-length clamping to reduce setup time and tool wear; the DIN‑compliant design and universal ER 25 fit ensure straightforward integration into existing toolholding systems. Order directly through Metav Werkzeuge or consult our specialists for application advice. TECWERK ER 25 Collet — 5 mm, DIN 6499‑B compliance The TECWERK ER 25 Collet is a precision clamping sleeve for ER 25 toolholders, designed to secure 5 mm shank tools with high repeatability in milling and drilling operations. 5 µm runout repeatability Conforms to DIN 6499‑B standard Clamping diameter 5 mm, length 34 mm Full-length grip, fits ER 25 chucks Consistent precision for repeatable clamping High machining quality starts with stable clamping. The clamping sleeve delivers 5 µm runout repeatability, which minimises radial play and supports consistent surface finish and longer tool life. By reducing micro‑vibration and eccentric loading, the result is fewer rejects and lower rework rates. The precise runout performance translates directly into measurable savings in cycle time and consumable costs for production environments that demand reliable tolerances. Compatibility that reduces setup complexity Built to the DIN 6499‑B specification, this collet integrates seamlessly with standard ER 25 chucks, eliminating uncertainty during upgrades or replacements. The design permits a full-length grip and allows clamping on the lead chamfer, so tools are held along their working length for superior support. The ability to bridge gaps by nominal minus 1.0 mm reduces the need for intermediate sizes, simplifying inventory and accelerating tool changes on busy shop floors. Practical dimensions and handling benefits Compact dimensions aid efficient handling without compromising stiffness: L: 34 mm, D: 26 mm and a clamping diameter of 5 mm match common tooling requirements. The sleeve's geometry ensures the tool is retained evenly across the clamping zone, improving repeatability and concentricity in serial production. For workshops seeking predictable performance from standardised components, this clamping sleeve offers a balance of convenience and industrial robustness. For DIN‑compliant clamping and assured repeatability, choose TECWERK collets via Metav Werkzeuge — contact Metav Werkzeuge for ordering and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000832926NW Product type: ER collet Label: Spannzange Typ ER 25/430 E Spann‑D.5mm TECWERK Manufacturer: TECWERK Packaging unit: 1 Facts Clamping diameter: 5 mm Length L: 34 mm d: 5 mm D: 26 mm Runout / repeatability: 5 µm Span bridging: nominal minus 1.0 mm Special features Complies with DIN 6499‑B Suitable for ER 25 collet chucks Full‑length holding; can be clamped on lead chamfer No intermediate sizes required FAQ How accurate is the clamping with this collet? The collet provides a runout repeatability of 5 µm, ensuring high concentricity when used in ER 25 chucks; the TECWERK ER 25 Collet (SKU 2000832926NW) is designed for precision retention. Will this collet fit existing ER 25 toolholders? Yes, the sleeve is manufactured to DIN 6499‑B and is compatible with standard ER 25 chucks, allowing direct replacement without adapter modifications. What does "span bridging nominal minus 1.0 mm" mean in practice? It means the collet can reliably clamp shank diameters up to 1.0 mm below the nominal size, reducing the need for additional intermediate collet sizes. Can the tool be clamped on the lead chamfer with this sleeve? Yes, the design supports clamping along the full length and permits secure retention on the lead chamfer for improved support. What are the key dimensions to check before ordering? Confirm the clamping diameter (5 mm), the overall length (L: 34 mm) and the outer diameter (D: 26 mm) to ensure compatibility with the toolholder and the intended tool shank. TECWERK: Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
34mm ER 25 Collet For 4mm Clamping Diameter, 5 µm Runout Accuracy - TECWERK
Reliable clamping accuracy and a compact form factor make this collet a practical choice for precision shops; the combination of 5 µm runout and full-length grip supports repeatable production results. Order the collet directly via Metav Werkzeuge or ask the Metav consultants if further specification is required. Collet type ER 25/430 E — ER 25 collet, 4 mm clamping diameter (TECWERK) The Collet type ER 25/430 E is a compact ER 25 collet designed for precision clamping in metalworking and general workshop applications using standard ER collet chucks Compatible with ER 25 collet chucks Full-length gripping for tool stability Runout and repeatability 5 µm accuracy Clamping diameter 4 mm, compact L 34 mm Consistent precision for repeatable machining results The clamping system is engineered for high repeatability: runout and repeatability of 5 µm ensure that tools remain concentric under repeated changeover, which reduces rework and setup time. Conformance with DIN 6499-B signals compatibility with established workshop standards and simplifies integration into existing tool sets. Such measurable precision converts directly into predictable machining results and lower scrap rates, an advantage in batch production and prototype runs alike. Strong, full-length clamping improves tool stability The collet holds tools along the entire clamping length, providing a full-length grip that increases stability and vibration damping during cutting. The design allows clamping on the pilot chamfer where appropriate, enabling secure retention even when the shank engages a guiding taper. The clamping diameter compensation (nominal minus 1.0 mm) permits small diameter bridging without additional adapters, preserving process reliability while maintaining concentricity. Compact dimensions for practical workshop use Compact dimensions such as L: 34 mm, D: 26 mm and a clamping bore of 4 mm reduce spindle intrusion and make the item suitable for tight setups. Standardised form and compatibility with ER chucks remove the need for intermediate sizes, streamlining inventory and tool management. The small footprint supports flexible tool configurations on milling heads and drill spindles while maintaining the stability expected from a workshop-grade clamping system. Practical benefits that support productivity and trust Standardisation and predictable performance shorten setup routines and support efficient production planning. As a standard ER 25 clamping sleeve, the item helps reduce spare-part varieties and contributes to a clearer tool pool. Metav’s quality filter for the European market ensures that components supplied through Metav Werkzeuge meet consistent expectations—useful when scaling operations or centralising procurement for multiple workshops. Contact Metav Werkzeuge today for order and technical advice on the TECWERK ER 25/430 E collet and ensure rapid, reliable supply from Emmerich. Technical data Article number: 2000832925NW Type: ER 25 collet Product: Collet type ER 25/430 E Facts Clamping diameter (d): 4 mm Outside diameter (D): 26 mm Length (L): 34 mm Runout / repeatability: 5 µm Clamping diameter compensation: nominal − 1.0 mm Special features According to DIN 6499-B Compatible with ER collet chucks No intermediate sizes required Tools clamped along full clamping length; can be clamped on pilot chamfer Suitable for bridging clamping diameters (nominal − 1.0 mm) FAQ What level of concentricity can be expected with this collet? The TECWERK ER 25/430 E collet delivers runout and repeatability of 5 µm, providing the concentricity required for precise milling and drilling operations. Is the collet compatible with standard ER 25 chucks? Yes — the clamping sleeve is compatible with standard ER 25 collet chucks and conforms to DIN 6499-B, ensuring interchangeability. Can tools be clamped on the chamfer or only on the cylindrical shank? Tools can be clamped along the entire clamping length and may also be secured on the pilot chamfer, offering greater flexibility for different tool geometries. What are the key dimensions of this collet? Dimensions: clamping bore 4 mm, outside diameter 26 mm, length 34 mm; SKU 2000832925NW. Is an intermediate collet size required for non-standard diameters? No — intermediate sizes are not required; the collet is designed to bridge small diameter differences up to the clamping diameter compensation of nominal − 1.0 mm. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
35mm Clamping Screw M12 For Clamping Ø27mm, L22mm K8mm - TECWERK
Compact M12 thread and compliance with DIN 6367 combine to provide dependable clamping for a 27 mm toolholder; take advantage of the compact 22 mm length and 35 mm head for secure seating. Order this TECWERK component directly via Metav Werkzeuge or consult our specialists for fit verification. TECWERK M12 milling clamping screw – compact M12 thread for 27 mm clamping diameters The TECWERK M12 milling clamping screw serves as a compact draw-in screw for milling toolholders and clamping systems, optimised for applications with a clamping diameter of 27 mm M12 thread for standard toolholders Designed for clamping Ø 27 mm Overall length 22 mm, head Ø 35 mm DIN 6367 conformity Consistent clamping performance for accurate machining A precise M12 thread combined with conformity to DIN 6367 ensures repeatable seating and predictable force transmission, which is crucial for milling operations that demand positional accuracy. The screw’s geometry supports consistent axial pull and stable contact between the tool and holder, reducing micro‑movement during cuts. This results in improved surface finish and tool life, as fewer compensatory adjustments are required during set‑up. The standardised specification also simplifies inventory planning in production environments where interchangeability and traceable components are essential. Faster set-up and less downtime through compact dimensions With an overall length of 22 mm and a head diameter of 35 mm (head height K 8 mm), the component is designed for compact assemblies and tight tool pockets. The short shank minimises protrusion into the toolholder, enabling quicker insertion and removal while maintaining a secure clamp. For workshops that cycle tools frequently, these dimensions translate into measurable time savings at every tool change and fewer obstructions during handling and storage, supporting leaner workflows and higher machine uptime. Industrial compatibility and reduced sourcing complexity Specification to an established standard makes the screw suitable for a broad range of holders and milling systems that accept an M12 draw-in element and a 27 mm clamping interface. The standardised profile facilitates cross‑brand compatibility and reduces the risk of procurement errors in mixed fleets. Where standardisation is part of a quality strategy, the use of DIN‑compliant components simplifies documentation and quality audits while supporting consistent assembly procedures across departments. Practical applications and workshop recommendations This clamping screw is aimed at industrial workshops, tool rooms and maintenance departments that require compact, standardised fastening for milling toolholders with a 27 mm clamping diameter. Given the absence of material data in the specification, compatibility checks with existing holders and any surface‑treatment requirements should be confirmed before installation. For bespoke toolrooms or retrofit projects, selecting a DIN‑specified fastening element like this one reduces the need for custom adaptations and helps maintain reliable clamping under routine operational stresses. For compatibility checks or to secure the correct TECWERK M12 component for a 27 mm toolholder, contact Metav Werkzeuge for tailored advice and ordering support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000834074NW Product: Milling clamping screw Manufacturer: TECWERK Core data Thread: M12 Suitable for clamping diameter: 27 mm Overall length (L): 22 mm Head diameter (D): 35 mm Head height (K): 8 mm Pack unit: 1 Special features Conforms to DIN 6367 Compact design for confined tool pockets FAQ What thread does the clamping screw use? The clamping screw uses an M12 thread as specified for the TECWERK milling clamping screw (SKU 2000834074NW). Which clamping diameter is the screw intended for? The component is specified for a clamping diameter of 27 mm, matching standard toolholders that accept this interface. What are the key dimensions to check before installation? Check the overall length 22 mm, head diameter 35 mm and head height K 8 mm to ensure clearance and correct seating in the holder. Does the screw meet an industrial standard? Yes, the screw is manufactured to DIN 6367, supporting interchangeability and documented quality requirements. Is material information provided for corrosion or lubrication considerations? Material is not specified in the provided data; it is recommended to confirm material and surface treatment requirements prior to use. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
35mm Face Clamping Chuck Weldon 10mm Collet, DIN 69871 Form AD/B, SK40 50mm - TECWERK
Take advantage of a DIN 69871-compliant SK40 interface, central coolant supply and a secure Weldon lateral drive to reduce tool change times and improve process reliability; order the face clamping chuck directly via Metav Werkzeuge or consult our specialists for application advice. Face clamping chuck DIN 69871 AD/B — Weldon drive, central coolant, SK40 The Face clamping chuck DIN 69871 AD/B is a SK40 taper tool holder designed for secure clamping of tools with a 10 mm shank and for use in machining centres that require DIN-standard tool interfaces. DIN 69871 AD/B compatibility Central coolant supply with re-sealable channels Weldon drive for secure lateral tool retention Suitable for 10 mm tool shank, SK40 taper Reliable interface for uninterrupted machining The holder provides a DIN 69871 interface with a steep taper to ensure repeatable seating and high concentricity. The combination of the SK40 taper and a Weldon lateral drive creates a robust mechanical connection that resists axial and radial forces during milling and drilling. The internal bore tolerance H4 guarantees tight concentricity for reduced run-out, which translates into longer tool life and improved surface finish. For production environments this means fewer stoppages and more consistent part quality, making the arbor an efficient choice for repetitive operations. Targeted coolant delivery to extend tool life Equipped with a central coolant supply and re-sealable coolant channels at the flange, the arbor directs cutting fluid precisely to the tool interface. Side coolant channels accommodate tools with a cylindrical shank and lateral drive according to DIN 1835-B, improving chip evacuation and thermal control at the cutting edge. The result is reduced heat-related wear and longer intervals between tool replacements, which lowers consumable costs and maintains cutting performance under prolonged cycles. Compact dimensions for straightforward integration The face clamping chuck features a flange diameter D: 35 mm and a projection A: 50 mm, with a clamping diameter of 10 mm and bore tolerance H4 for reliable tool retention. The compact geometry simplifies integration into existing SK40 spindles and keeps tool overhang to a minimum, helping to reduce vibration and improve accuracy. Manufactured to recognised standards, the holder is suited for workshops and production lines seeking a standardised, low-maintenance toolholding solution that supports predictable machining outcomes. For DIN-standard toolholding from TECWERK with integrated coolant management, contact Metav Werkzeuge for tailored advice and rapid supply via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000833771NW Product type: Face clamping chuck Brand: TECWERK Standard: DIN 69871 Form AD/B Facts Diameter D: 35 mm Clamping diameter: 10 mm Projection A: 50 mm Bore tolerance: H4 Special features Weldon lateral drive for tool take-up Central coolant supply Re-sealable coolant channels at the flange Side coolant channels for cylindrical shank tools per DIN 1835-B FAQ What spindle taper does the chuck use? The chuck is supplied as a SK40 taper according to DIN 69871 AD/B, making it compatible with machines that accept this interface. Which tool shank diameter is supported? This TECWERK face clamping chuck is specified for a 10 mm clamping diameter and a bore tolerance of H4 for precise seating. Does the holder provide coolant to the cutting zone? Yes. The arbor features a central coolant supply plus re-sealable channels and side coolant ports to target fluid to the tool and improve chip evacuation. Is this chuck suitable for tools with a Weldon shank? The holder includes a Weldon lateral drive and is designed to accept tools with a lateral drive surface in accordance with DIN 1835-B, ensuring positive torque transmission. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
35mm Face Clamping Chuck Weldon Shank DIN 69871 Form AD, 10mm Clamping Diameter / A50mm - TECWERK
Take advantage of the combination of repeatable clamping, DIN-standard compatibility and compact projection for reliable toolholding. Order the TECWERK Weldon face clamping holder directly via Metav Werkzeuge or consult our specialists for application-specific advice. TECWERK Weldon Face Clamping Holder DIN 69871 Form AD – SK40, 10 mm clamping diameter, 50 mm projection The TECWERK Weldon Face Clamping Holder DIN 69871 Form AD is a SK40 taper tool holder designed to secure cylindrical‑shank cutters with a lateral Weldon drive flat, providing standardised mounting for conventional and CNC spindles. Weldon flat for positive lateral drive Steep taper DIN 69871 Form AD Clamping diameter 10 mm H4 tolerance SK40 taper compatibility Consistent concentricity for precision machining The steep taper interface DIN 69871 Form AD paired with a defined H4 bore tolerance ensures a close, repeatable fit between spindle and holder. That dimensional accuracy reduces radial runout and provides consistent repeatability across tool changes, which improves surface finish and prolongs cutter life. The Weldon drive flat contributes to secure torque transmission without relying solely on friction, so rotational accuracy is preserved under load. Broad compatibility with cylindrical‑shank cutters Designed for tools with a cylindrical shank and lateral drive flat to DIN 1835‑B, this holder accepts a clamping diameter of 10 mm, with an overall diameter of 35 mm and a projection length (A) of 50 mm. The SK40 taper makes the holder suitable for many machining centres and toolholders, enabling quick integration into existing setups. This compatibility helps maintain machining flexibility while keeping tooling standardised. Practical advantages for the workshop and production line The compact design and standard conformity facilitate straightforward inspection and replacement planning. With clear dimensional references—D = 35 mm, A = 50 mm, clamping Ø = 10 mm—maintenance routines can be standardised and spare parts stocked sensibly. The positive lateral drive and standard taper support reliable high‑precision operation in short‑ and medium‑run production, delivering operational confidence and reduced setup variability. For ordering, technical clarifications or to discuss specific applications of the TECWERK SK40 Weldon holder, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 — our team will advise on integration and compatibility with existing tooling systems. Technical data Article number: 2000833723NW SKU: 2000833723NW Name: Weldon face clamping holder DIN 69871 Form AD Type: Face clamping holder Standard: DIN 69871 Form AD Label: Weldon Spann‑D.10mm SK40 A.-L.50mm TECWERK Facts Diameter D: 35 mm Projection A: 50 mm Clamping diameter d: 10 mm (H4 tolerance) Packaging unit: 1 Special features Weldon flat for lateral drive Steep taper interface per DIN 69871 Form AD For cylindrical shank tools with lateral flat to DIN 1835‑B SK40 taper connection Brand: TECWERK FAQ What shank types are compatible with this holder? The TECWERK Weldon face clamping holder is made for cylindrical‑shank cutters with a lateral Weldon drive flat according to DIN 1835‑B; it secures a 10 mm shank. Which taper does the holder use? The tool holder uses an SK40 taper and complies with DIN 69871 Form AD, ensuring compatibility with matching SK40 spindles and adaptors. What is the clamping tolerance and why does it matter? Clamping bore tolerance is H4, which ensures a precise fit and improved concentricity for repeatable machining accuracy with minimal radial runout. Can the holder be used in CNC machining centres? Yes, the combination of SK40 taper, Weldon drive flat and standardised dimensions makes this holder suitable for both conventional and CNC machines requiring defined tool engagement. How long is the projection and how does it affect rigidity? Projection (A) is 50 mm; a shorter projection generally increases rigidity, so this compact length balances reach with stability for many workshop applications. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
35mm Face Clamping Chuck Weldon Shank HSK-A63 10mm Clamping Diameter DIN 69893 Form A - TECWERK
Take advantage of the combination of fast tool changes, reliable axial security and precise clamping for uninterrupted machining cycles; the Weldon flat clamping arbor with HSK-A63 interface and 10 mm clamping diameter delivers repeatable results and straightforward integration. Order directly via Metav Werkzeuge or request tailored advice from our consultants. Weldon flat clamping arbor DIN 69893A HSK-A63 – 10 mm clamping, 100 mm length (TECWERK) A Weldon flat clamping arbor DIN 69893A HSK-A63 designed for secure clamping of tools with cylindrical shanks and lateral drive flats, suitable for high-precision CNC milling applications Weldon side drive for axial retention HSK-A63 interface for high-speed spindles 10 mm clamping diameter for cylindrical shanks 100 mm overall length for extended reach Faster set-ups through precise HSK connection The HSK interface significantly reduces runout and increases repeatability compared with conventional taper holders. The HSK-A63 connection ensures a rigid, axial and radial fit during both torque and centrifugal loads, which shortens set-up time and reduces rework. With the hollow shank taper DIN 69893 Form A design, the arbor seats positively in the spindle, improving concentricity and enabling consistent clamping accuracy for serial machining tasks. These mechanical benefits translate directly into higher throughput and lower scrap rates on production lines. Secure axial retention with Weldon side drive The Weldon flat provides mechanical axial retention for tools with a lateral drive face per DIN 1835-B, preventing end-play under heavy cutting forces. This side-drive arrangement complements the HSK taper by offering a secondary retention principle that is particularly valuable when machining at elevated feed rates or when interrupted cuts occur. The combination of taper seating and Weldon drive reduces the risk of tool pull-out and helps maintain tool orientation, thereby preserving cutting edge life and process stability. Compatibility and practical dimensions for workshop use Key dimensions support versatile application: clamping Ø 10 mm for standard cylindrical shanks, an external diameter of 35 mm and an overall length of 100 mm provide balance between reach and rigidity. The arbor is specified with bore tolerance H4, which standardises the fit with Weldon-style tools and supports interchangeability across tool inventories. For machine shops seeking a compact yet robust holder, this solution integrates with HSK-A spindles and common milling tool stocks without compromising stiffness. Reduced downtime through straightforward maintenance and fitting The design focuses on pragmatic maintenance: the hollow-shank taper facilitates easy cleaning of the seating surfaces and the Weldon flat is a proven, low-maintenance retention method. Regular inspection of seating faces and flats prevents contamination-related runout. When installed and maintained according to spindle and toolholder guides, the arbor supports predictable tool life and fewer unplanned tool changes, contributing to a stable production schedule and lower total process cost. For procurement or application-specific advice on the TECWERK Weldon flat clamping arbor with HSK-A63, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility and delivery options. Technical data Article number: 2000832372NW Designation: Weldon flat clamping arbor DIN 69893A, 10 mm clamping, HSK-A63, 100 mm length, TECWERK Product type: Flächenspannfutter / clamping arbor Interface: HSK-A Core measurements Diameter D: 35 mm Clamping Ø d: 10 mm Length A: 100 mm Bore tolerance: H4 Special features Weldon side drive for lateral retention Hollow shank taper DIN 69893 Form A For cylindrical shank tools with lateral drive per DIN 1835-B Packaging unit: 1 FAQ Which spindle types are compatible with this arbor? The arbor is made for HSK-A spindles and fits HSK-A63 interfaces; the Weldon flat clamping arbor DIN 69893A HSK-A63 works with spindles designed for DIN 69893 Form A toolholders. What shank styles can be clamped with this holder? Tools with cylindrical shanks and a lateral drive flat according to DIN 1835-B are compatible; the holder's 10 mm clamping diameter secures such shanks reliably. How does the Weldon feature improve safety during machining? The Weldon side drive provides mechanical axial retention in addition to the taper fit, reducing the chance of tool pull-out during heavy cuts or interrupted machining. Is the bore tolerance specified for accurate tool interchange? Yes, the arbor is supplied with bore tolerance H4, supporting consistent fits and interchangeability across matching tool shanks. Can this holder be used for high-speed machining? The HSK-A63 interface and the hollow shank taper DIN 69893 Form A are engineered for high-speed applications where precise seating and reduced runout are required; ensure spindle specifications and balancing procedures are followed. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
35mm Face Clamping Holder Weldon 10mm Clamping Diameter, DIN 69893 Form A HSK-A63 - TECWERK
Taking advantage of a compact 35 mm body and a HSK‑A63 interface combined with a Weldon flat provides dependable torque transmission and repeatable clamping for tools with cylindrical shanks; order directly via Metav Werkzeuge or contact the consultants for tailored integration into existing toolholding systems. Face clamping chuck DIN 69893A, Weldon, 10 mm clamping Ø, HSK‑A63 — TECWERK The face clamping chuck DIN 69893A (Weldon) HSK‑A63 is a toolholder designed to securely clamp cylindrical‑shank cutters with lateral drive surfaces in HSK‑A toolholders, suitable for precision machining and retrofit on HSK‑A63 spindles. HSK‑A63 interface for secure tool holding Weldon flat for lateral drive per DIN 1835‑B 10 mm clamping diameter with H4 bore tolerance Compact 35 mm body, A length 65 mm Improved machining reliability through optimised retention and interface design The compact face clamping chuck combines the short taper of the HSK‑A63 interface with a Weldon flat to ensure positive torque transmission and minimal slip during heavy cuts. Compared with conventional taper‑only holders, the lateral drive surface secures tools with a DIN 1835‑B clamping profile, reducing micro‑movement and improving tool life. The result is consistent component quality, fewer rework cycles and a measurable reduction in downtime for critical production runs. Faster set‑up and consistent concentricity thanks to precision bore tolerance A bore manufactured to H4 tolerance and a nominal clamping diameter of 10 mm support tight concentricity and repeatable seating of cylindrical shanks. The compact body (Ø 35 mm) and A length 65 mm allow straightforward insertion into standard HSK‑A63 toolholders, shortening changeover time and enabling predictable spindle dynamics. This precision reduces the need for constant re‑measuring and assists in maintaining cycle times across batch production. Broad compatibility with standardised tooling for reduced inventory complexity Designed to accept tools with a cylindrical shank and lateral engagement to DIN 1835‑B, the chuck offers straightforward compatibility with common cutter types used in milling and drilling operations. The Weldon configuration translates into simple mechanical engagement without custom adapters, helping to consolidate tooling stock while preserving machining flexibility. This compatibility supports lean workshop inventories and simplifies tool management strategies. Robust design that supports predictable maintenance and integration Built to the DIN 69893 Form A specification with a hollow shank taper, the chuck is intended for repeated mountings and operational cycles typical in production environments. The HSK‑A interface facilitates rapid automatic seating and removal, while the Weldon drive delivers secure mechanical indexing under load. Where process reliability and repeatability are priorities, this configuration reduces the variables that can affect machining tolerances and streamlines preventive maintenance planning. For a bespoke technical evaluation and reliable supply of TECWERK clamping solutions, contact Metav Werkzeuge for advice and rapid fulfilment from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000832387NW Label: Flächenspannfutter DIN 69893A Weldon Spann‑D.10mm HSK‑A63 A.‑L.65mm TECWERK Manufacturer: TECWERK Facts Diameter D: 35 mm Clamping Ø d: 10 mm A: 65 mm Bore tolerance: H4 Special features HSK‑A interface, Form A (DIN 69893) Weldon flat for tools with DIN 1835‑B lateral drive Suitable for cylindrical shanks FAQ What tool shank types can be clamped with this chuck? The face clamping chuck accepts tools with a cylindrical shank and a lateral drive surface to DIN 1835‑B, making it suitable for most Weldon‑style cutters. Is the holder compatible with HSK‑A63 spindles? Yes, the unit uses the HSK‑A interface in accordance with DIN 69893 Form A and is intended for direct mounting in HSK‑A63 toolholders. What level of concentricity is guaranteed by the bore tolerance? The bore is manufactured to H4 tolerance, supporting tight concentricity and repeatable seating of a 10 mm clamping diameter. Can this chuck transmit high torque for heavy milling operations? The Weldon flat combined with the HSK‑A63 interface provides positive lateral drive and reliable torque transmission for demanding machining tasks. Is the product suitable for retrofitting existing toolholding systems? Yes, its compact dimensions (Ø 35 mm, A 65 mm) and adherence to DIN 69893 make it compatible with standard HSK‑A63 setups and straightforward to integrate. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
35mm Face Clamping Holder With 10mm Weldon Collet, Internal Coolant, DIN 69893 Form A - TECWERK
Take advantage of a secure HSK‑A63 interface, integrated internal coolant and a 10 mm Weldon clamping face for consistently stable machining results; order the face clamping chuck directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Face clamping chuck HSK‑A63 (Weldon, 10 mm clamping Ø) by TECWERK Face clamping chuck HSK‑A63 (Weldon, 10 mm clamping Ø) offers a hollow‑shank taper per DIN 69893 Form A for secure toolholding in high‑precision machining and turning applications. HSK‑A63 secure interface Internal coolant channels for through‑coolant Weldon flat for positive tool drive Consistent, accurate clamping for demanding machining A holder with a hollow shank taper (DIN 69893 Form A) provides a rigid connection to HSK‑A spindles, reducing runout and improving repeatability. The integrated Weldon flat supplies a lateral drive face in accordance with DIN 1835 B, ensuring positive torque transmission for tools with cylindrical shanks. This combination of features results in improved positional stability during milling and drilling operations and helps maintain tool geometry over longer production runs. Integrated coolant routing that protects tools and workpieces The face clamping chuck includes internal coolant supply and side coolant channels, designed for tools with cylindrical shanks. Directed coolant reduces thermal load at the cutting edge, lowers the risk of built‑up edge and chip welding, and supports higher local feed rates where appropriate. For workshops aiming to increase tool life and maintain surface quality, the coolant integration delivers measurable production benefits while keeping setup straightforward. Straightforward compatibility and quick change‑overs With an HSK‑A63 shank interface and a 10 mm clamping diameter, the chuck suits common tool inventories and is compatible with standard Weldon‑style shank tools. The compact A‑length of 65 mm and a 35 mm outer diameter make the holder suitable for many spindle‑tooling envelopes without compromising access to the workpiece. The design allows efficient tool changes and minimal adjustment time, supporting higher machine uptime and predictable process planning. For ordering or technical consultation on the TECWERK face clamping chuck (SKU 2000833837NW) contact Metav Werkzeuge directly at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss machine compatibility and application details Technical details Article number: 2000833837NW Description: Face clamping chuck DIN 69893 Form A, Weldon, clamping Ø 10 mm Brand: TECWERK Shank interface: HSK‑A Dimensions & measurable data Nominal diameter (D): 35 mm Clamping diameter (d): 10 mm A‑length: 65 mm Norm: DIN 69893 Form A Packaging unit: 1 Features & special functions Hollow shank taper according to DIN 69893 Form A Side coolant channels for cylindrical‑shank tools Lateral Weldon drive face to DIN 1835 B Internal coolant (through‑coolant) supply FAQ What machine spindles is this holder compatible with? The face clamping chuck is designed for HSK‑A63 spindles per DIN 69893 Form A, providing the intended taper and clamping fit for compatible machine interfaces. Can coolant be passed through the chuck to the cutting edge? Yes. The holder features internal coolant supply and side coolant channels to feed tools with cylindrical shanks directly, supporting cooling at the cutting zone. Which tool shank types are driven reliably by the Weldon flat? Tools with a cylindrical shank and a matching Weldon flat for lateral drive are suitable; the chuck’s lateral drive face conforms to DIN 1835 B for positive torque transmission. What clamping diameter and overall dimensions should be noted for setup? Clamping diameter is 10 mm, outer diameter is 35 mm, and A‑length is 65 mm, which should be checked against the machine’s tooling envelope. Is this holder suitable for high‑precision repeatability applications? The hollow shank taper, secure HSK‑A63 interface and Weldon drive are intended to reduce runout and improve repeatability, making the holder suitable for precision machining tasks. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
360mm HSK63 Tool Holder Compact 10-Slot Polypropylene, Impact and Coolant Resistant - TECWERK
Take advantage of the combination of robust HSK63 mounting, a space-saving compact 10-slot layout and durable polypropylene construction for orderly tool storage and faster changeovers; order the TECWERK tool holder directly via Metav Werkzeuge or request technical advice from Metav's consultants. TECWERK Tool holder HSK63 — polypropylene, compact 10-slot (360 x 180 x 60 mm) The TECWERK Tool holder HSK63 polypropylene compact is a workshop-grade storage insert designed for organised holding of HSK63 tool interfaces in production and service environments. HSK63 interface for secure mounting Compact 10-slot design Polypropylene, impact-resistant Acid- and coolant-resistant, black Optimised storage that shortens setup times The compact 10-slot layout and defined HSK63 receptacles create a tidy system for staging tooling prior to machine changeovers. The structured arrangement reduces search and handling time, supporting quicker tool changeovers and improved process flow. Specified dimensions 360 x 180 x 60 mm allow integration into benches, trolleys or drawer systems; the modest mass (170 g) keeps handling effortless while preserving positional stability. Clear organisation of the tooling inventory enhances operational efficiency without additional handling equipment. Durable polypropylene body built for workshop conditions Manufactured from polypropylene, the carrier offers resistance to impacts and breakage typical in busy shops. The polymer is acid-resistant and coolant-resistant, so exposure to cutting fluids or mild chemical residues during routine handling will not compromise function. The combination of chemical compatibility and mechanical resilience reduces replacement frequency and maintenance effort. The material choice also keeps the insert lightweight while maintaining the dimensional stability required for repeatable seating of the HSK63 interfaces. Secure seating and compatibility with HSK63 tooling The HSK63 interface pockets ensure axial and radial support for holders and adaptors, preserving concentric alignment during storage and handling. This precise seating minimises the risk of damage to taper faces and reduces the need for rework after storage. The compact format provides ten defined positions in a small footprint, which is advantageous for workshops aiming to consolidate tool storage without increasing footprint. The product name appears on technical specifications and order references for accurate identification. Practical benefits for workshop logistics and safety By combining a robust polymer construction with a dedicated HSK63 layout, the holder reduces clutter and protects expensive tool tapers from knocks and contamination. The design supports a safer workshop environment by preventing loose tooling on benches and transport trolleys. Rational gains include reduced downtime for locating tools and fewer tool replacements due to accidental damage, while the organised presentation of tooling aids inventory checks and shift handovers. For tailored supply or advice on integrating the TECWERK HSK63 tool holder into existing storage systems, contact Metav Werkzeuge — Metav's Emmerich team will provide reliable fulfilment and application guidance. Technical Data Article number: 9000453684NW Brand: TECWERK Product type: Tool holder Facts Interface: HSK63 Version: compact 10-slot Dimensions: 360 x 180 x 60 mm (B x T x H) Weight: 0.17 kg Special features Material: polypropylene Colour: black Impact- and break-resistant Acid- and coolant-resistant FAQ What interface does this holder accept? The holder accepts HSK63 tool interfaces and is made for secure seating of HSK63 holders. Is the insert suitable for use with cutting fluids? Yes. The polypropylene body is coolant-resistant and resists common workshop fluids. How many tools can be stored in one compact unit? The compact version provides ten defined slots for organised storage of ten HSK63 interfaces. What are the external dimensions for drawer or cupboard planning? Overall dimensions are 360 x 180 x 60 mm, suitable for bench inserts or small storage drawers. Is the unit lightweight for frequent handling? At approximately 170 g, the unit is lightweight while retaining structural rigidity for repeated use. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
38mm Cross-Slot Adapter Arbor With 16mm Collet, DIN 69871 Form AD/B, Central Coolant - TECWERK
Benefit from a stable, standardised machine interface combined with active coolant management for longer tool life and reliable chip evacuation; the enlarged collar and 16 mm clamping diameter ensure secure mounting and repeatable results. Order the arbour directly via Metav Werkzeuge or consult our advisors for compatibility and delivery options. Cross-slot mounting milling arbour (DIN 69871 AD/B) — SK40, 16 mm clamping Ø, TECWERK The cross-slot mounting milling arbour is a SK40 taper accessory for the secure installation of cutter heads and slot cutters to DIN 1880, designed for machining tasks that demand rigid clamping and effective coolant delivery. Enlarged collar diameter for greater stability Central coolant supply with resealable channels Steep taper to DIN 69871 Form AD/B Engineered for secure clamping and consistent concentricity The arbour is built around a steep taper (DIN 69871 AD/B) and a SK40 seating to provide a rigid spindle-to-tool connection that reduces vibration and runout. With a 16 mm clamping Ø, the design supports precise retention of cutters and heads with a cross slot to DIN 1880, so concentricity and repeatable positioning are achieved across batch production. The enlarged collar diameter increases bearing surface and resists bending moments, which translates into improved surface finishes and reduced rework in demanding milling operations. Optimised coolant routing for improved tool life and process stability Integrated central coolant supply and resealable coolant channels at the collar, together with additional coolant bores on the face, enable targeted delivery of cutting fluid to the tool interface. This configuration aids in effective chip removal and thermal control, which in turn lowers cutting temperatures and extends cutter life. The possibility to close channels at the collar gives flexibility in different machining setups, while the radial and face coolant exits promote consistent lubrication and reduce the risk of clogging during interrupted cuts. Practical compatibility and workshop benefits Designed to receive cutter heads and slot cutters to DIN 1880, the arbour supports straightforward integration into existing tool sets and changeover processes. The combination of standardised taper, clear dimensional data and active coolant features reduces setup time and simplifies inventory management for production and jobbing shops. Conformity to recognised standards provides an additional layer of reliability for quality assurance procedures, while the robust mechanical design contributes to predictable process outcomes and lower overall operating costs. Contact Metav Werkzeuge today to discuss the TECWERK SK40 arbour (SKU 2000833815NW), verify compatibility with current tooling and request a tailored quotation — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 2000833815NW Label: Quernutaufsteckfräsdorn DIN 69871AD/B Spann-D.16mm SK40 A.-L.35mm TECWERK Type: Cross-slot mounting milling arbour Standard: DIN 69871 Form AD/B Facts Diameter D: 38 mm Clamping Ø d: 16 mm A (projection): 35 mm L1: 17 mm Packaging unit: 1 Special features Enlarged collar diameter Steep taper to DIN 69871 Form AD/B Central coolant supply Resealable coolant channels at the collar Additional coolant bores on the face For cutter heads and cutters with cross slot to DIN 1880 SK40 shank FAQ What cutters are compatible with this arbour? The arbour accepts cutter heads and slot cutters designed with a cross slot to DIN 1880; compatibility is ensured when the cutter conforms to that standard. How is coolant supplied to the tool? Coolant is delivered via a central supply through the taper with resealable channels at the collar and additional bores on the face to direct fluid to the cutting zone. What taper and shank does the arbour use? The product uses a DIN 69871 Form AD/B steep taper with a SK40 shank for machine spindle mounting (SKU 2000833815NW). Why choose an enlarged collar diameter? An enlarged collar diameter increases bearing surface and resistance to bending, improving stability and concentricity during heavy or interrupted milling. Can coolant channels be closed for dry machining? Yes, the collar channels are designed to be resealable, providing flexibility to run with or without internal coolant routing. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
38mm Cross-Slot Adapter Arbor With Enlarged Collar, Hollow Shank DIN 69893 Form A, 16mm Clamping - TECWERK
Take advantage of the arbor's combination of HSK-A63 shank standard conformity, enlarged collar for increased rigidity and through-face coolant bores for reliable chip evacuation to maintain consistent machining quality. Order the TECWERK arbor directly via Metav Werkzeuge or consult Metav's specialists for application-specific advice. Transverse-slot mounting arbor HSK-A63, clamping Ø16 mm – TECWERK The transverse-slot mounting arbor by TECWERK is a DIN 69893 Form A tool holder for secure attachment of cutter heads and milling cutters with a transverse slot, designed for precision slot milling applications. Enlarged collar for higher rigidity Hollow shank taper to DIN 69893 Form A Face coolant bores for directed coolant flow For cutter heads and cutters with transverse slot Improved rigidity for reproducible slot precision The arbor delivers a stable connection between machine spindle and tooling thanks to its enlarged collar diameter and HSK interface. Increased collar mass reduces deflection under cutting loads, which directly improves dimensional accuracy and surface finish when producing transverse slots. This stability is particularly beneficial in high-precision milling setups, where tool bending can cause tolerance drift; the design helps to maintain repeatability across batches while reducing rework and scrap. Effective coolant routing to protect cutting edges Integrated coolant channel bores at the face provide a direct path for lubrication and cooling to the cutter interface, aiding heat control and chip evacuation. By directing coolant to the cutting zone, the arbor helps to extend tool life and maintain cutting performance during longer cycles. The combination of internal coolant routing and a hollow shank taper supports consistent thermal conditions at the tool holder, which contributes to steady machining results and fewer unplanned tool changes. Conformity with standards and broad tool compatibility Manufactured to DIN 69893 Form A, the arbor mates with HSK-A63 spindles and accepts cutter heads and milling cutters with a transverse slot to DIN 1880. The clear specification of the shank geometry and mounting interface simplifies tool selection and setup in CNC environments, enabling predictable clamping behaviour and fast tool changes. This standard conformity reduces setup time and ensures interchangeability within established tooling systems. Practical dimensions for workshop efficiency Key dimensions are optimised for common slot-milling tasks: a nominal diameter of 38 mm, a clamping diameter of 16 mm and a functional projection length of 50 mm with a 17 mm segment relevant for the mounted tool. These measures support a compact yet robust tool assembly that balances reach and stiffness, making the arbor suitable for repetitive production runs where consistent performance and straightforward inspection are required. Contact Metav Werkzeuge for tailored technical advice and to arrange procurement of this TECWERK HSK-A63 transverse-slot mounting arbor for stable, standard-compliant slot milling operations. Technical data Article number: 2000833875NW Product type: Transverse-slot mounting arbor Shank: HSK-A63 Standard: DIN 69893 Form A Brand: TECWERK Core data Diameter D: 38 mm Clamping diameter d: 16 mm A (projection length): 50 mm L1: 17 mm Special features Enlarged collar diameter Hollow shank taper to DIN 69893 Form A Coolant channel bores at the face For cutter heads and cutters with transverse slot to DIN 1880 FAQ What spindle interface does this arbor use? The arbor uses an HSK-A63 interface in accordance with DIN 69893 Form A, ensuring secure clamping and fast tool changes. Which cutter types can be mounted on this arbor? Cutter heads and milling cutters designed for a transverse slot to DIN 1880 can be mounted on the TECWERK transverse-slot mounting arbor. How does the coolant supply work on this arbor? Coolant is supplied via face bores that direct lubricant to the cutter interface, supporting chip evacuation and temperature control. Will the enlarged collar improve machining stability? Yes, the enlarged collar diameter increases rigidity at the tool holder junction, reducing deflection and improving repeatability during slot milling. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
38mm Transverse Slot Arbor With 16mm Collet, Hollow Shank, Coolant Ports, DIN 69893 Form A - TECWERK
Take advantage of the combination of enhanced stability, integrated coolant routing and precise HSK‑A63 toolholding for reliable milling performance; order the arbor directly via Metav Werkzeuge or consult our specialists for technical clarification. Arbor for cross‑slot cutters — TECWERK, HSK‑A63, Ø38 mm, 100 mm projection The arbor for cross‑slot cutters is designed for HSK‑A63 spindles and for mounting cutter heads and cutters with a DIN 1880 cross slot, offering stable, coolant‑ready toolholding for production and jobbing shops Enlarged flange diameter for improved rigidity Hollow shank taper to DIN 69893 Form A Front coolant channel drilling for directed cooling Accepts DIN 1880 cross‑slot cutter heads Increased rigidity for stable milling results The arbor is engineered to deliver consistent concentricity and elevated stiffness thanks to an enlarged flange diameter combined with a Ø38 mm body. Increased flange mass reduces bending under load, which lowers vibration and improves surface finish in slotting and face‑milling tasks. For workshops seeking reproducible cutting results, this results in fewer rejects and reduced rework; the mechanical design supports higher radial stability without additional adaptations to the spindle. Precise HSK‑A63 compatibility and secure clamping Built to DIN 69893 Form A, the toolholder features the HSK‑A63 interface that is widely used for high‑accuracy, high‑speed machining. The hollow shank taper ensures correct seating and repeatable positioning, while the clamping diameter 16 mm enables direct acceptance of shank‑mounted components designed to DIN 1880. This results in short set‑up times and reliable torque transmission, making the arbor suitable for series production as well as single‑piece finishing where positional accuracy is essential. Integrated coolant provision for longer tool life The face of the arbor is supplied with additional coolant channel drilling, allowing directed coolant delivery to the cutting zone when combined with appropriate supply lines. Internal coolant routing via the hollow shank minimises thermal build‑up at the cutter interface and enhances chip evacuation. The result is improved tool life and more consistent machining, particularly in operations that generate heat or demand continuous material removal. Practical application and user advantages This toolholder is intended for the reception of cutter heads and cutters with a DIN 1880 cross slot, offering a straightforward retrofit into machining centres equipped with HSK‑A spindles. The design simplifies mounting of cross‑slot tooling, reduces balancing effort compared with ad‑hoc adaptors and supports higher feed rates through increased structural rigidity. Combined with Metav’s distribution and advisory services, this arbor is a practical choice for workshops wishing to standardise on robust, DIN‑compliant toolholding. Contact Metav Werkzeuge for tailored advice on HSK‑A63 toolholding and rapid supply from Emmerich—benefit from our precision expertise and stock availability Technical data Article number: 2000833876NW Manufacturer: TECWERK Facts Standard: DIN 69893 Form A Interface: HSK‑A63 Body diameter: 38 mm Clamping diameter: 16 mm Projection length: 100 mm L1: 17 mm Special features Enlarged flange diameter for improved rigidity Hollow shank taper according to DIN 69893 Form A Additional coolant channel drilling at the face Designed to receive cutter heads and cutters with DIN 1880 cross slot FAQ What spindle interface does this arbor use? The arbor uses an HSK‑A63 interface compliant with DIN 69893 Form A to ensure accurate seating and repeatable positioning. Can the arbor accept cutter heads with a DIN 1880 cross slot? Yes, the toolholder is specifically designed for the reception of cutter heads and cutters with a DIN 1880 cross slot. How does the coolant routing improve machining? Integrated coolant channel drilling at the face directs coolant to the cutting edge, reducing temperature, aiding chip evacuation and extending tool life. What are the key dimensions to consider for setup? Important dimensions include a body diameter of 38 mm, a clamping diameter of 16 mm, and a 100 mm projection length, which determine fixture clearance and tool reach. Is the arbor suitable for high‑speed machining? The hollow shank and HSK‑A63 connection support accurate centring and dynamic balance, making the arbor suitable for demanding machining conditions when correctly specified. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
3mm ER 25 Collet, 34mm Length, Clamping Range 3mm, 5 µm Runout - TECWERK
Precision and compatibility combine in this TECWERK ER 25 collet: full‑length clamping and a 5 µm runout rating ensure steady, reproducible toolholding for small‑diameter tooling. Benefit from DIN 6499‑B conformity and the ability to bridge undersized tools (nominal −1.0 mm). Order the collet directly via Metav Werkzeuge or ask the consultants for tailored advice. ER 25 Collet 430 E – 3 mm clamping diameter (TECWERK) The ER 25 Collet 430 E is a DIN‑compliant collet designed for ER‑type holders, providing secure, full‑length clamping of 3 mm tools for precision machining applications. DIN 6499-B compatibility Full-length clamping for secure grip Runout and repeatability: 5 µm Clamping diameter 3 mm, length 34 mm Consistent precision for demanding toolholding Designed to meet DIN 6499‑B, this collet delivers repeatable runout of 5 µm, which translates into more accurate cuts and improved surface finishes. The full‑length clamping mechanism grips the tool along its entire clamping length and also accepts bracing on the leading chamfer, reducing axial play and vibration. For production runs where consistency matters, the technical specification—d = 3 mm, L = 34 mm, D = 26 mm—supports predictable performance and helps maintain tool life by limiting undesired deflection. Faster setups and stable production processes Compatibility with standard ER chucks eliminates the need for intermediate sizes and simplifies tooling changes, so set‑up times are reduced and throughput increases. The collet’s ability to bridge smaller diameters (clamping range: nominal −1.0 mm) allows secure gripping of slightly undersized tools without additional adapters. This functional flexibility supports leaner inventories of clamping accessories and fewer interruptions on the shopfloor, delivering a measurable efficiency advantage for workshops and toolrooms. Suitable for precision shops and general machining The ER 25 collet is suited to tasks that require reliable clamping of small‑diameter cutters and drills in milling and machining centres. By ensuring low runout and uniform grip, the component supports higher tolerances and repeatability in series production as well as prototyping. Where accurate concentricity and repeatability are required, the collet’s combination of ER system compatibility and defined dimensional data ensures predictable integration into existing clamping setups. For secure, repeatable clamping of small‑diameter tooling, contact Metav Werkzeuge to discuss the TECWERK ER 25 collet (SKU 2000832924NW) and arrange procurement or technical advice; email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 2000832924NW Type: ER 25 Brand: TECWERK Product type: ER collet Packing unit: 1 Dimensions & accuracy Clamping diameter (d): 3 mm Length (L): 34 mm Outside diameter (D): 26 mm Runout / repeatability: 5 µm Clamping range bridging: nominal −1.0 mm Compatibility & features DIN 6499‑B standard Fits ER collet chucks Full‑length clamping; tools can be clamped on the chamfer No intermediate sizes required FAQ What clamping diameter does the collet support? The collet supports a 3 mm clamping diameter and bridges undersized tools up to nominal −1.0 mm for secure retention. Is this collet compatible with standard ER chucks? Yes. The design conforms to DIN 6499‑B and fits ER‑type collet chucks used in milling and machining setups. How precise is the runout of the collet? The TECWERK ER 25 collet is specified with a runout and repeatability of 5 µm, ensuring consistent concentricity for precision work. Can tools be clamped on the chamfer with this collet? Yes. The collet allows full‑length clamping and can also retain tools when supported on the leading chamfer, enhancing versatility. What are the main dimensions to consider when integrating this collet? Key dimensions are clamping diameter 3 mm, length 34 mm and outside diameter 26 mm; these values support correct selection for ER 25 holders. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com