Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
11.79mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of precision and robust workshop execution to ensure reliable hole checks and fast fixture set‑ups; the 11.79 mm diameter and 50 mm length offer a stable reference with a tolerance of ±0.002 mm. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.B79 (single) — 11.79 mm ⌀, 50 mm length (Metav IndustryLine) A single gauge pin M323.B79 designed for precise hole inspection and fixture alignment in workshop environments Precision diameter 11.79 mm, tolerance ±0.002 Hardened special-steel construction 50 mm length for standard inspection use Workshop-grade finish for robust daily handling Consistent dimensional control for routine inspection The pin provides a reliable reference for bore checks and alignment tasks, reducing rework by offering repeatable measurements. With a diameter of 11.79 mm and a specified deviation of ±0.002 mm, the component is suited to applications where small tolerances decide part acceptance. The precision-ground surface minimises measurement uncertainty and enables quick comparison against drawing limits, which supports faster decision-making on the shop floor. Simple integration into gauges and fixtures As a single, straight reference pin, this item fits into existing fixture bores and gauge plates without modification, helping to shorten set‑up times. The 50 mm length provides sufficient engagement for stable locating while remaining easy to handle, and the special steel construction ensures dimensional stability under normal workshop stresses. The result is improved setup repeatability and fewer adjustments during production runs. Built for everyday workshop use and traceability The workshop-grade execution delivers durability for frequent handling and regular inspection cycles. At a nominal weight of 0.1 kg the pin is straightforward to position and transport between workstations. Supplied as an individual item with the declared technical data, the pin supports consistent quality routines and integrates into inspection protocols where a clear, measurable reference is required. Contact Metav Werkzeuge today to specify the M323.B79 gauge pin for fixture or inspection tasks, or consult our specialists for application-specific recommendations Technical Data Article number: M323.B79 GTIN: 4061905064869 Brand: Metav IndustryLine Material: Special steel EClass: 21170231 Facts Diameter: 11.79 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Single gauge pin Workshop-grade execution Precision-ground finish FAQ What tolerance can be expected from this gauge pin? The M323.B79 gauge pin is specified with a tolerance of ±0.002 mm, suitable for fine inspection and control applications. Is the pin suitable for use as a locating dowel in fixtures? Yes, the single pin design and special steel construction make it appropriate for use as a locating reference in many fixture set-ups where the diameter and length match the task. How does the pin support repeatable measurements? A precision-ground surface and a tightly held diameter of 11.79 mm ensure repeatability by providing a stable, invariant reference for successive checks. Can this pin be used on automated inspection benches? The robust finish and precise dimensions allow integration into mechanical gauge assemblies and many automated test stations that accept single reference pins. What maintenance is recommended to keep accuracy? Regular cleaning to remove swarf and corrosion protection after use will preserve the precision surface and maintain the declared tolerance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.7mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Taking advantage of high repeatability, ±0.002 mm tolerance and robust special‑steel construction ensures reliable end‑dimension checks in production and inspection. Order the test pin directly via Metav Werkzeuge or consult our advisors for application guidance. Test pin M323.B70 — Single gauge pin, Ø 11.7 mm, 50 mm length (Metav IndustryLine) A Test pin M323.B70 for precise end‑dimension checks and simple gauging tasks in workshop and quality‑control environments. Tolerance ±0.002 mm Special steel construction Ø 11.7 mm gauge diameter 50 mm overall length Accuracy that reduces rework and speeds inspection The gauge is engineered for consistent metrological performance: with a tolerance of ±0.002 mm and a compact form, it offers dependable comparative measurements during incoming inspection or final checks. The compact geometry minimises deflection and enables rapid validation of bore sizes or end dimensions, helping to reduce non‑conformances and downstream rework. The construction concentrates on repeatability and clear go/no‑go assessment rather than complex adjustment, which translates into faster cycle times at the inspection bench. Robust design for everyday workshop use A special‑steel body provides mechanical resilience against knocks and repeated handling typical in a production environment. The 50 mm overall length with a 11.7 mm diameter gives a solid feel in the hand and easy seating in gauges, sockets and fixtures without excess overhang. As a workshop execution item, the component balances durability with serviceability: the simple geometry is tolerant to standard cleaning and storage routines and supports predictable contact behaviour during manual measurements. Practical benefits and trust in supply Selected for routine end‑dimension controls, this single gauge pin suits batch checks, fixture making and quick functional tests where clear, objective results matter. The compact format and proven material choice allow integration into existing gauge sets and checks with minimal adaptation. Supply is secured through Metav’s European distribution network, which combines a broad product range with local stock control—an advantage for consistent replenishment and traceable sourcing. Speak to Metav Werkzeuge in Emmerich to request supply of the workshop‑grade test pin M323.B70 with ±0.002 mm tolerance and to discuss availability and delivery options Technical data Article number: M323.B70 GTIN: 4061905063732 Manufacturer: Metav IndustryLine Facts Diameter: 11.7 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Single test pin ECLASS: 21170231 FAQ What material is the gauge pin made from? The M323.B70 test pin is manufactured from special steel, selected for its mechanical resilience and stable contact behaviour. Is the tolerance suitable for precision inspection work? Yes, the ±0.002 mm tolerance positions the pin for precise comparative checks and reliable end‑dimension verification in workshop and QA settings. Can this pin be used with standard gauge holders and sockets? The Ø 11.7 mm diameter and 50 mm length make the pin compatible with common holders and fixtures used for go/no‑go and seating checks. Is the pin intended for laboratory calibration or everyday workshop use? The design and designation indicate a workshop execution, optimised for robust, routine use rather than delicate laboratory-only applications. What is the SKU for ordering and traceability? Order reference: M323.B70; GTIN 4061905063732 for inventory and traceability purposes Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.81mm Gauge Pin 50mm Length Workshop Version Special Steel - Metav IndustryLine
Benefit from workshop‑grade construction combined with 11.81 mm diameter accuracy and a tight ±0.002 mm tolerance for reliable end‑measurement results; order directly via Metav Werkzeuge or consult our specialists for supply and application advice. Gauge pin, single — 11.81 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.B81 is a precision test pin designed for dimensional verification and end‑measure checks in workshop and light‑production environments. Diameter 11.81 mm precision Tolerance ±0.002 mm 50 mm special‑steel length Workshop‑grade construction Accuracy that stabilises production quality The compact test pin delivers a measurable improvement in repeatability through its ±0.002 mm specification, which corresponds to high fine‑measurement performance in workshop settings. Such a tolerance reduces measurement scatter during inspection and supports consistent pass/fail decisions on small batches. The pin’s geometry ensures a defined contact surface for end‑gauging, which simplifies comparative checks and lowers the probability of false rejects during routine quality control. Micro‑range dimensions for fine components Classified in the micro measurement range, the pin’s 11.81 mm diameter and 50 mm length suit tasks where minimal intrusion and precise seating are necessary. This size is advantageous for toolrooms, small assembly stations and precision‑parts inspection where reach and stiffness must be balanced. The short, stiff profile helps to keep deflection negligible, improving confidence when measuring shafts, bores or dowel seats that demand tight dimensional control. Built for workshop use and lasting service Manufactured from special steel, the component combines surface integrity with the mechanical resilience required for regular handling in a production environment. The workshop‑oriented finish assists sliding and seating during repeated checks, while the modest mass keeps handling straightforward. As a single‑piece gauge pin it integrates easily into existing inspection jigs or hand‑held verification routines, offering a durable alternative to improvised measurement methods and supporting consistent results over many cycles. Select the Metav IndustryLine M323.B81 when precise micro‑gauging is required and contact Metav Werkzeuge GmbH for customised delivery or product advice from Emmerich’s precision specialists Technical Data SKU: M323.B81 GTIN: 4061905064883 Manufacturer: Metav IndustryLine Facts Diameter: 11.81 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Precision class: fine micro measurement FAQ What inspection tasks is this gauge pin suited for? The gauge pin is intended for end‑measure checks, seating verification and dimensional pinpointing of small shafts and bores; the M323.B81 from Metav IndustryLine performs reliably in micro‑measurement applications. How precise is the M323.B81 in practical use? With a specified tolerance of ±0.002 mm, the pin provides high repeatability suitable for workshop and small‑series inspection tasks, supporting strict dimensional control. Can this pin be integrated into measurement fixtures? Yes, the single‑piece construction and standard dimensions allow straightforward integration into jigs and fixture setups for comparative or reference measurements. What material properties support long service life? Produced from special steel, the pin combines wear resistance with dimensional stability, ensuring consistent contact geometry over extended inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.82mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise, workshop‑grade reference measurement with a 11.82 mm diameter gauge pin manufactured from special steel, offering a defined tolerance of ±0.002 mm and a stable 50 mm working length for repeatable end‑measure tasks. Order the gauge pin M323.B82 directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.B82 — Workshop‑grade precision pin, 11.82 mm diameter, 50 mm length (Metav IndustryLine) The M323.B82 gauge pin provides a compact, robust reference for end‑measurement and setting operations in inspection benches and fixture setups, designed for everyday workshop use. Workshop‑grade construction Diameter 11.82 mm, tolerance ±0.002 mm Stable 50 mm working length Special steel for wear resistance Exact, measurable repeatability for inspection work A compact reference pin with a nominal diameter of 11.82 mm and a declared geometric deviation of ±0.002 mm delivers quantifiable repeatability that supports reliable inspection routines. The controlled tolerance reduces ambiguity during go/no‑go checks and comparative gauging, which shortens decision cycles on the shop floor and improves throughput. Built as a single precision pin, it functions as a stable reference for end‑measure operations, enabling clear pass/fail outcomes in fixture setups and component validation. The data‑driven advantage is particularly relevant where traceable, repeatable dimensions prevent rework and downstream assembly issues. Robust workshop design that stands up to daily use Constructed from special steel, the pin balances hardness and toughness to withstand regular seating and withdrawal in holders and nests without premature wear. The 50 mm length provides a solid contact surface that minimises tilting during measurement while keeping handling straightforward for technicians. The workshop‑grade finish lowers the need for frequent replacement, supporting predictable service intervals and reducing indirect costs associated with downtime. Its compact mass and geometry simplify integration into established inspection jigs and portable gauge sets. Practical applications and process benefits Designed primarily for end‑measure and reference applications, the pin is suited to fixture alignment, dimensional spot checks and use as a datum in assembly operations. Marked traceability via SKU and GTIN supports inventory control and quality documentation in regulated production environments. When used consistently within a measurement routine, the pin helps tighten process control, offering a measurable improvement to inspection consistency and a corresponding reduction in non‑conforming parts. Compatibility with standard pin holders and nests makes retrofitting into existing workflows straightforward. Request supply of Metav IndustryLine gauge pins via Metav Werkzeuge for dependable end‑measure accuracy and hands‑on advice from the Emmerich team Technical Data Article number: M323.B82 GTIN: 4061905064890 Manufacturer: Metav IndustryLine Category: Gauge pins / Messstifte Material: Special steel Version: Workshop‑grade Core measurements Diameter: 11.82 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features and applications Workshop‑grade construction End‑measure reference pin Fixture alignment and spot checks Traceable SKU/GTIN for inventory control Suitable for repetitive inspection tasks FAQ What is the declared tolerance of the gauge pin? The M323.B82 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.002 mm for reliable comparative measurements. Which material is used for the pin body? This gauge pin is manufactured from special steel, selected for wear resistance and suitability for repeated seating in holders and nests. Can the pin be used for fixture alignment and end‑measure checks? Yes — the Metav IndustryLine M323.B82 is intended as a workshop‑grade reference pin for fixture alignment, end‑measure tasks and spot checks. How is the product referenced for ordering and traceability? The item is listed under SKU M323.B82 and GTIN 4061905064890 to support inventory, ordering and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.83mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact inspection solution that combines a 11.83 mm diameter, ±0.002 mm tolerance and a 50 mm length for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for set compatibility. Gauge pin, single — 11.83 mm diameter, ±0.002 mm accuracy (Metav IndustryLine) A Gauge pin (single), 11.83 mm diameter and 50 mm length designed for precise end measurements, fixture checks and workshop inspection tasks 11.83 mm diameter for precise fits Tolerance ±0.002 mm for tight control 50 mm length for fixture and end measurements Workshop execution, robust single item Engineered for measurable accuracy The design delivers a measurable advantage where tolerance matters: with an indicated ±0.002 mm variation the pin supports quality control tasks that demand close dimensional conformity. Specified as a compact reference element with a 11.83 mm diameter, this inspection pin enables repeatable checks on mating bores, alignment seats and end faces. The use of special steel provides a stable contact surface that resists wear during routine use; this reduces rework and preserves downstream process stability. Engineers and inspectors will value the clear numeric performance that feeds directly into statistical process control and first‑article inspection routines. Built for everyday workshop inspection Configured as a single, workshop version component, the pin’s 50 mm length balances handling and reach for common inspection stations and fixture set‑ups. The robust execution makes it suitable for frequent loading into gauges and holders, while the modest 0.1 kg mass keeps handling straightforward during manual procedures. As a compact reference part, the item integrates easily into inspection kits or bench sets and helps standardise go/no‑go confirmations and alignment tasks. Confidence in physical checks contributes to a smoother production flow and fewer stoppages. Integration that supports process reliability Incorporating this test element into inspection plans provides a direct benefit to traceability and documentation: the pin serves as a simple, numeric reference that can be recorded alongside measurement results and process audits. The single‑piece configuration suits bespoke measurement routines as well as replacement stock for larger gauge assemblies. For procurement, the Metav IndustryLine label indicates availability through an established supply channel, backed by a European quality filter that keeps inventory reliable and deliveries transparent. The clear specification streamlines selection for maintenance teams and quality engineers alike. For workshop‑grade precision and compatibility advice, contact Metav Werkzeuge to specify matching gauges, replacement parts or set‑up recommendations at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: M323.B83 GTIN: 4061905064906 Material: special steel Type: workshop execution Item: single gauge pin Category: gauge pins Core dimensions Diameter: 11.83 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Designed for end measurements Robust workshop design Single‑piece supply Suitable for fixture and inspection use FAQ What is the exact diameter of this gauge pin? The gauge pin is specified at 11.83 mm diameter for tight fit and alignment tasks. What tolerance can be expected during inspection use? The item is rated at ±0.002 mm, enabling precise comparative and go/no‑go checks. Which material is used for the pin? The pin is made from special steel, chosen for wear resistance in routine workshop inspection. Is this supplied as a single piece or in sets? This listing describes a single gauge pin supplied individually; sets can be assembled from individual items as required. For which applications is this pin best suited? Ideal for end‑measure checks, bore verification and fixture alignment in workshop and inspection environments; it functions as a compact reference element for dimensional control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.84mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combining ±0.002 mm repeatability with a special steel construction and a compact 50 mm length delivers a reliable solution for end‑measure inspections in busy workshops; ideal where reproducible results and robust handling matter. Order the test pin directly via (Metav Werkzeuge) or ask our consultants if needed. Test pin, single, 11.84 mm, length 50 mm — Metav IndustryLine gauge pin with ±0.002 mm tolerance The Test pin, single, 11.84 mm, length 50 mm is a compact workshop gauge pin designed for precise end‑measure verifications and fixture checks in production and inspection environments. Tolerance ±0.002 mm Workshop version, robust design Supplied in transport case Precise checks for compact components This compact gauge element is intended for fast, repeatable end‑measure readings where a short, stiff probe delivers low deflection. Constructed from special steel, the pin maintains geometric stability during routine handling and fits inspection jigs and go/no‑go fixtures without excessive setup time. The ±0.002 mm tolerance gives clear, measurable confidence in small‑part inspection and supports efficient quality control workflows by reducing rework and ambiguity in pass/fail decisions. Reproducibility and handling benefits With a nominal diameter of 11.84 mm and a 50 mm overall length, the probe is classed within the Micro measurement range, making it particularly suitable for fine mechanical tasks and compact assemblies. The short gauge length minimises bending and operator influence, so measurements are more reproducible compared with longer pins. The workshop version finish balances corrosion resistance with the wear resistance needed for regular contact checks, enabling longer service intervals and consistent performance on the shop floor. Integration, packaging and everyday applications The design supports straightforward integration into inspection benches, thread‑gauging rigs and component end‑face tests. Supplied in a transport case, the pin is protected during storage and transit and arrives ready for use in maintenance rounds or small series inspection. Typical uses include end‑measure verification of machined shafts, fixture alignment checks and reference pins for pneumatic or manual assembly stations. The robust material choice reduces the risk of surface damage during handling and preserves the calibrated geometry under normal workshop conditions. Contact Metav Werkzeuge today to reserve the Metav IndustryLine test pin M323.B84 and discuss batch quantities or inspection integration via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.B84 GTIN: 4061905064913 Label: Prüfstift, einzeln, 11.84 mm Länge 50 mm Manufacturer: Metav IndustryLine Dimensions & accuracy Diameter: 11.84 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & features Material: special steel Workshop version Supplied in transport case eClass: 21170231 FAQ What applications is this test pin designed for? The test pin (Test pin, single, 11.84 mm, length 50 mm) from Metav IndustryLine is designed for end‑measure checks, fixture alignment and small‑part inspection where a compact, stiff gauge pin is required. What accuracy can be expected with this gauge pin? This Metav IndustryLine gauge pin offers a tolerance of ±0.002 mm, providing the high repeatability needed for precise workshop inspections (SKU M323.B84). Is the pin protected for transport and storage? Yes, the test pin is supplied in a transport case to protect the probe during transit and storage and to keep the geometry free from handling damage. Which material is used for this test pin and what does that mean for wear? Manufactured from special steel, the Metav IndustryLine test pin combines surface robustness with dimensional stability, which helps reduce wear during regular contact inspections. Into which measurement class does this test pin fall? With a maximum measuring range of 11.84 mm, the pin falls into the Micro measurement class, suitable for fine mechanical work and compact component testing. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.85mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Precision engineering for end-dimension checks: this gauge pin combines ±0.002 mm tolerance, Ø11.85 mm diameter and a 50 mm length in a robust workshop design. Ideal where repeatable fit verification is required, it offers compact handling and reliable traceability — Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single Ø11.85 mm × 50 mm (M323.B85) — Workshop version, high precision, Metav IndustryLine Gauge pin, single Ø11.85 mm × 50 mm is a compact workshop test pin for fast end-measurements and fit checks in production and inspection environments. Workshop-ready design Precision tolerance ±0.002 mm Diameter Ø11.85 mm for end measurements Special-steel construction for durability Consistent results for critical end-measurements The gauge pin delivers high reproducibility thanks to its fine tolerance of ±0.002 mm, which keeps measurement scatter to a minimum during go/no-go or comparative checks. Such accuracy ensures that mating parts and bores meet functional requirements without repeated adjustments. The reduced measurement uncertainty translates into fewer rework cycles and a steadier production flow, supporting efficient quality control routines. Robust construction tailored to workshop use Manufactured from special steel, the pin withstands handling and typical workshop influences while preserving its measuring surface. The workshop version balances hardness and corrosion resistance to retain roundness and length under frequent use. The 50 mm overall length with Ø11.85 mm diameter provides a compact feel that is easy to position in fixtures and test rigs, helping operators perform quick, repeatable checks on finished components. Practical role in inspection workflows As a single precision gauge pin, this item is suited for end-dimension verification, fit gaging and go/no-go applications where a defined cylindrical reference is required. Its compact geometry allows straightforward integration into manual or jig-based inspections and it is particularly helpful for final checks during assembly. The compact classification places it in the micro measurement range (max 10–100 mm), making it especially useful for small to medium components where stiffness and handling are decisive. Confidence from a specialist supplier Sourcing from an experienced metrology partner brings additional assurance: Metav IndustryLine supplies the component with clear identification and logistic support from Emmerich. The combination of a specialist steel grade and a workshop-oriented finish ensures durable performance across repetitive inspection tasks, which supports production reliability and reduces the risk of unexpected downtime. Request M323.B85 from Metav Werkzeuge in Emmerich — our specialists can advise on application suitability, compatibility with existing fixtures and arrange supply to match inspection cycles Technical data Article number: M323.B85 GTIN: 4061905065682 SKU: M323.B85 Facts Diameter: 11.85 mm Length: 50 mm Tolerance/variation: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Design: Workshop version Application focus: end-dimension checks / fit verification Category: Gauge pin (single) FAQ What level of accuracy does this gauge pin provide? The gauge pin offers a declared variation of ±0.002 mm, making it suitable for fine workshop inspections and repeatable fit checks where tight tolerances are required. Is the pin supplied as a single item or in a set? This product is supplied as a single gauge pin (single item), sold individually under SKU M323.B85 for flexible use in inspection routines. For which measurement range is this pin intended? With a diameter of Ø11.85 mm and a 50 mm length, the pin falls into the micro measurement range (max 10–100 mm) and is aimed at small to medium-sized components and end-measurements. What material is the pin made from and why does that matter? The shaft is produced from special steel, which provides a balance of surface hardness and durability so that roundness and length stability are maintained under regular workshop use. How is this component typically used in quality control? The pin is used for end-dimension verification, fit gaging and quick go/no-go checks in assembly and inspection stations; it serves as a compact cylindrical reference for mating parts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.86mm Gauge Pin, Workshop Version, 50mm Length, ±0.002 Accuracy - Metav IndustryLine
Take advantage of a compact, workshop-ready gauge pin that combines tight tolerance and robust material for consistent end‑measure verification. The combination of 11.86 mm diameter, ±0.002 mm accuracy and a 50 mm length ensures reliable fit checks and repeatable measurements; order via Metav Werkzeuge or consult our advisors for rapid delivery. Gauge pin M323.B86 — 11.86 mm diameter, 50 mm length (Workshop version) by Metav IndustryLine The gauge pin M323.B86 is a single precision test pin designed for end‑measure verification and fit inspection in workshop and production‑control environments. Workshop version for daily inspection 11.86 mm precision diameter ±0.002 50 mm length for compact components Delivered in protective transport case Precision where it matters This test pin delivers consistent dimensional control thanks to a diameter of 11.86 mm produced to a tolerance of ±0.002 mm. Such accuracy supports tight assembly and clearance checks where repeatability is essential; the small form factor and controlled surface finish make the pin suitable for validating bores, alignment seats and mating parts. By converting nominal dimensions into verifiable pass/fail results, the pin reduces rework and increases throughput during incoming inspection and in‑process checks. Built for workshop reliability Manufactured from special steel, the component is specified as a workshop version that balances durability with handling convenience. The material choice provides resistance to everyday wear while maintaining the measuring diameter over repeated cycles; the pin’s manageable 50 mm length and 0.1 kg mass make it easy to position and stable during visual and tactile inspection routines. The design minimises operator influence on the result, supporting reliable comparisons between batches and production shifts. Handling and storage that speeds inspection To protect accuracy in transit and at the bench, the item is delivered in a protective transport case appropriate for workshop use. The storage solution reduces the risk of surface damage or contamination that could affect the ±0.002 mm tolerance, so the pin remains ready for immediate use when required. Compact storage also simplifies kit assembly for mobile metrology setups and keeps inspection stations tidy, improving workflow efficiency during repetitive quality checks. Typical applications and compatibility Ideal for end‑measure verification, fit checks and short‑run inspection tasks, the pin is suited to component assemblies, jigs and fixtures where a single, stable reference plug is required. The gauge pin performs well for bore gauging and alignment validation of compact components and is a practical complement to more complex measuring systems in the workshop. Where a straightforward, repeatable reference is needed, this pin provides a cost‑effective solution without sacrificing measured certainty. For precise inspection work with Metav IndustryLine components, contact Metav Werkzeuge for personalised advice on using the M323.B86 in production and to arrange prompt shipment from Emmerich; info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.B86 GTIN: 4061905065699 Label: Gauge pin, single, 11.86 mm diameter, 50 mm length Facts Diameter: 11.86 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Delivered in protective transport case FAQ What tolerance does the gauge pin offer? The gauge pin is manufactured to an accuracy of ±0.002 mm, making it suitable for tight fit and clearance checks. Which material is the pin made from? The tool is made from special steel, specified for workshop durability and consistent dimensional retention. Is the pin suitable for bore gauging and fit checks? Yes, the gauge pin M323.B86 is intended for end‑measure verification, bore gauging and simple fit inspections in workshop environments. How is the item supplied to protect accuracy? The item is supplied in a protective transport case to reduce the risk of surface damage and maintain the specified tolerance. What is the product identifier for ordering? Order using article number M323.B86 or GTIN 4061905065699 for clear reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.87mm Gauge Pin 50mm Length, Workshop Version, ±0.002 Accuracy - Metav IndustryLine
The robust workshop gauge pin combines a precise Ø 11.87 mm diameter, a 50 mm working length and a tight tolerance of ±0.002 mm for dependable end‑measurement and alignment; order the M323.B87 directly via Metav Werkzeuge or consult our technical advisors for application support. M323.B87 gauge pin — Ø 11.87 mm, 50 mm length (Metav IndustryLine) A M323.B87 gauge pin engineered for accurate end‑measurement and component alignment in workshop environments. Workshop design for daily shop use Precision tolerance ±0.002 mm Diameter 11.87 mm, length 50 mm Supplied in protective transport case Consistent end‑measurement that keeps production moving The solid gauge pin delivers highly repeatable measurements thanks to its ±0.002 mm specification, which supports precise verification of bores, dowel seats and mating features. The compact geometry and defined shaft diameter provide a reliable datum for pass/fail checks; with a controlled tolerance, inspectors and machinists gain a measurable reduction in rework and inspection uncertainty. This section emphasises the practical benefit of improved process control rather than abstract features. Durability and workshop handling for everyday use Manufactured from special steel, the pin is designed as a workshop version able to withstand frequent handling and routine use in inspection benches and jigs. The 50 mm effective length balances reach and stiffness, reducing the risk of bending during insertion. Supplied in a protective transport case, the item remains protected during storage and transit, extending service life and preserving the calibrated condition achieved in production. Practical compatibility and application areas This single‑piece inspection pin suits a broad range of metrology tasks: alignment, plug checking, fixture set‑up and go/no‑go verification in assembly or inspection routines. The defined 11.87 mm diameter makes it suitable for accurate checks of nominal bores and for use as a reference pin in bespoke fixtures. Lightweight and easy to handle, the component integrates with standard measurement workflows and bench‑level tooling. Contact Metav Werkzeuge today to confirm the suitability of the M323.B87 gauge pin for specific production tasks and arrange delivery from our Emmerich warehouse Technical data Article number: M323.B87 GTIN: 4061905065705 Label: Prüfstift, einzeln, 11,87 mm Länge 50 mm Manufacturer: Metav IndustryLine Material: Spezial‑Stahl Facts Diameter: 11.87 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Supplied in transport case Single item (individual gauge pin) Category: Messstifte FAQ What level of precision can be expected from this gauge pin? The M323.B87 gauge pin is specified with a tolerance of ±0.002 mm, providing high repeatability for end‑measurements and alignment tasks. Which materials is the pin suitable for checking? As an inspection tool, the gauge pin is intended for dimensional verification of components made from metals and assemblies where a defined diameter reference is required. Is the pin supplied ready for use out of the box? The M323.B87 is delivered as an individual precision pin in a protective transport case; any specific calibration certificates can be requested if required for quality documentation. Can this pin be used in fixtures and jigs? Yes—its defined 11.87 mm diameter and 50 mm length make it suitable as a reference element in fixtures, alignment tools and go/no‑go checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.88mm Gauge Pin 50mm Length, Workshop Version, ±0.002 Accuracy - Metav IndustryLine
Take advantage of workshop-grade robustness and laboratory-level repeatability: the pin’s special steel construction and ±0.002 mm tolerance make it ideal for end measurements and fixture checks. Order the test pin directly via Metav Werkzeuge or consult our specialists for application guidance. Prüfstift, einzeln, 11.88 mm, length 50 mm — workshop test pin with ±0.002 mm accuracy Prüfstift, einzeln, 11.88 mm, length 50 mm is a single, precision test pin designed for repeatable end-measurement checks and gauge applications in workshop environments Workshop design for robust use Diameter 11.88 mm for precise fits Tolerance ±0.002 mm for repeatable checks Engineered precision for repeatable end measurements The workshop-grade test pin is made from special steel and finished to tight tolerances, delivering ±0.002 mm consistency for critical dimension checks. As a single-item probe with a 50 mm overall length and a nominal 11.88 mm diameter, it suits insertion gauges, plug gauges and fixture verification where repeatability matters. The compact mass (approx. 0.1 kg) reduces handling inertia and helps maintain stable seating in fixtures; such mechanical stability translates directly into fewer measurement scatter points and more reliable process control. Practical advantages for quality control workflows Designed as a workshop execution, the pin balances durability with measurement fidelity. The solid construction withstands routine handling on production floors while preserving the calibrated geometry required for accurate end measurements. Use as a reference element in inspection jigs or as a replacement gauge pin to restore conformity without recalibrating entire assemblies. The combination of special steel and careful manufacture reduces wear and ensures sustained contact geometry, minimising rework and downtime in serial inspection situations. Easy integration into existing inspection sets The single supplied pin format simplifies stocking and replacement logistics; its nominal 11.88 mm diameter matches precision fit requirements in standard gauge sets. Traceability is supported via the item identifiers provided, enabling clear part control within inspection documentation. Where matching to existing reference standards is required, the pin’s defined tolerance band and material homogeneity ensure predictable thermal and mechanical behaviour during short measurement cycles, facilitating consistent readings across shifts and operators. Reliable component for demanding measurement tasks Where compact, hard-wearing measurement elements are needed, this test pin performs as a dependable component in dimensional control chains. The workshop specification prioritises resistance to knocks and frequent use while maintaining the ±0.002 mm accuracy that underpins reliable pass/fail decisions. For operations that require straightforward, robust gauge elements—such as end-of-line checks, fixture validation and plug gauge replacements—this single test pin is a pragmatic choice that supports steady production quality. Contact Metav Werkzeuge to secure this workshop-grade test pin (SKU M323.B88) from the Metav IndustryLine range and discuss its suitability for specific gauge or fixture applications Technical Data Article number: M323.B88 GTIN: 4061905065712 Category: Test pin / Gauge pin Core specifications Diameter: 11.88 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Single item supply Workshop execution Material: special steel Intended use: end measurements FAQ What is the exact diameter and length of the test pin? The test pin has a diameter of 11.88 mm and a length of 50 mm, matching common gauge-fit requirements for end-measurement tasks. What tolerance can be expected from this workshop test pin? The pin is produced to an accuracy of ±0.002 mm, providing the repeatability needed for routine inspection and fixture checks. Is the pin suitable for use in production fixtures and plug gauges? Yes, the workshop execution and special steel construction make the pin suitable for use in production fixtures, plug gauges and similar inspection setups. How is the item identified for inventory and traceability? The item is listed under SKU M323.B88 with GTIN 4061905065712, enabling straightforward traceability in inspection records. Which applications benefit most from this test pin? Typical uses include end measurements, fixture verification and replacement of worn gauge pins where consistent dimensional control is required; the design supports repeatable checks in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.89mm Go/No-Go Gauge Pin 50mm Workshop Version Special Steel - Metav IndustryLine
Take advantage of high repeatability and robust special steel construction for reliable end‑measurements; the compact format and tight tolerance make this gauge pin ideal for workshop inspection and fixture setting. Order or enquire via Metav Werkzeuge for tailored advice and fast delivery. Gauge pin M323.B89 — single precision gauge pin, 11.89 mm ⌀, 50 mm length (Metav IndustryLine) The Gauge pin M323.B89 is a single precision measuring pin for end‑measurement, fixture alignment and go/no‑go checks in workshop and inspection environments. *Workshop version for robust on‑bench use *Precision tolerance ±0.002 mm *Diameter 11.89 mm, length 50 mm *Supplied in protective transport case Consistent accuracy that speeds up inspection cycles The M323.B89 delivers ±0.002 mm positional consistency, a level of repeatability suited for fine mechanical checks and quality control where narrow tolerances are required. Such accuracy reduces rework and inspection time by providing a reliable physical reference for gauging operations. In practice, the tight tolerance supports efficient quick‑checks and dimensional verification during production runs, improving throughput without sacrificing measurement confidence. Durable construction for everyday workshop handling Manufactured from special steel, this workshop‑grade pin withstands frequent handling and contact with fixtures while maintaining geometric stability. The 50 mm overall length and hardened finish keep deformation to a minimum under normal use, preserving the reference diameter 11.89 mm across repeated cycles. The robust build suits bench use and mobile inspection kits, offering a durable measuring element that retains form and functionality in daily industrial environments. Protected transport and predictable storage Delivery in a protective transport case safeguards the calibrated geometry and surface condition during transit and storage, reducing the risk of nicks or corrosion that would affect measurement integrity. A compact, protected package simplifies integration into tooling sets and inspection trolleys, ensuring the pin remains ready for immediate use on site or at the control bench. This reduces downtime associated with reconditioning or replacement. Practical uses and integration into workshop workflows The single‑pin format is tailored to end‑measurements, datum checks and fixture set‑up; it functions as a straightforward physical reference for pass/fail assessments and alignment tasks. Compatibility with standard handling tools and holders makes the element easy to incorporate into existing inspection procedures. The clear, robust design supports fast decisions on production floors and in maintenance operations where a simple, precise gauge is required. For reliable workshop metrology, request the Metav IndustryLine Gauge pin M323.B89 from Metav Werkzeuge — expert advice and ordering assistance are available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.B89 GTIN: 4061905065729 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 11,89 mm Länge 50 mm Dimensions and accuracy Diameter: 11.89 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Features and delivery Material: special steel Workshop version Single gauge pin Supplied in protective transport case Category: Messstifte eClass: 21170231 FAQ What level of accuracy does the M323.B89 provide? The M323.B89 gauge pin is specified with an accuracy of ±0.002 mm, offering high repeatability for precision end‑measurements and inspection tasks. Which material is the pin made from and why does that matter? The pin is made from special steel, chosen for wear resistance and dimensional stability so that the measuring diameter remains consistent during repeated use. How is the gauge pin supplied for transport and storage? The tool is supplied in a protective transport case, which protects the gauge from mechanical damage and environmental exposure during transport and storage. What are the typical applications for this gauge pin? Typical uses include end‑measurements, fixture alignment, datum setting and simple go/no‑go checks on the shop floor or in inspection benches. Which SKU identifies this product for orders and inventory? This item is listed as M323.B89 (Gauge pin M323.B89) and can be ordered via Metav Werkzeuge or referenced when requesting technical details. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.8mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Reliable probe for workshop inspection with ±0.002 mm repeatability and special steel durability — ideal for end-measure checks and fixture integration. Benefit from a compact Ø 11.8 mm profile and a 50 mm overall length for stable seating in gauge blocks. Order the test pin directly via Metav Werkzeuge or consult our advisors for specification matching. M323.B80 Test pin – probe pin Ø 11.8 mm, 50 mm length (Metav IndustryLine) The M323.B80 Test pin is a workshop-grade probe pin designed for end-measure and inspection applications, providing a compact, hard-wearing solution for repeatable gauging in production and quality control. Workshop version for routine use Diameter Ø 11.8 mm for tight fits Length 50 mm for stable seating High repeatability with ±0.002 mm accuracy Consistent precision for routine inspection A compact probe pin engineered to deliver consistent precision in repetitive checks. The specified ±0.002 mm variation indicates a tight manufacturing tolerance that reduces measurement scatter when used as a seating or reference element in inspection jigs. By keeping the functional diameter at 11.8 mm, the component offers reliable engagement in standard bores and fixtures, so axial positioning and contact consistency are improved. This level of control enhances process capability and reduces downstream rework. Robust workshop design that endures daily handling Constructed from special steel, the probe pin is built for frequent handling and workshop environments. The 50 mm overall length provides sufficient engagement without excess overhang, which helps to limit bending moments and maintain repeatability during quick checks. The workshop version designation reflects a balance between machinability and durability so that the element integrates well into repair benches, inspection stands and series gauging setups while keeping handling straightforward for operators. Easy integration into gauging workflows The component fits into common verification and end-measure tasks, functioning as a reference or contact pin in manual and semi‑automated fixtures. Traceability is supported by the visible SKU and GTIN for inventory and quality records; the compact form factor simplifies storage and replacement logistics. For procurement and process design the combination of workshop robustness and narrow tolerance makes this probe pin a pragmatic choice where stable contact geometry and short inspection cycles are required. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine test pin and to arrange delivery or technical matching by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: M323.B80 GTIN: 4061905064876 Brand: Metav IndustryLine Label: Test pin, single, Ø 11.8 mm, length 50 mm Category: Test pins Facts Diameter: 11.8 mm Length: 50 mm Tolerance / variation: ±0.002 mm Weight: 0.1 kg eCl@ss: 21170231 Special features Material: special steel Version: workshop execution Story trigger: end-measure applications Single item delivery FAQ What accuracy can be expected from this probe pin? The M323.B80 test pin is manufactured with a variation of ±0.002 mm, providing narrow scatter suitable for routine inspection and fixture reference duties. Is the probe pin suitable for integration into existing gauges and fixtures? Yes, the probe pin’s Ø 11.8 mm diameter and 50 mm length are intended for straightforward seating in common fixture designs and manual gauges; the Metav IndustryLine probe pin (SKU M323.B80) is optimised for such tasks. What material is used for the pin and how does that affect durability? The component is made from special steel, chosen to balance surface hardness and workshop durability so it withstands repeated contact and handling. Can the probe pin be used for end-measure checks on small bores? The compact diameter and short overall length make the pin suitable as an end-measure contact for small to medium bores where a stiff, repeatable contact element is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.91mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact workshop pin combining 11.91 mm gauge size, 50 mm length and a tight ±0.002 mm tolerance for reliable end‑measure checks; order the test pin directly via Metav Werkzeuge or consult our advisors if further specification is required. Test pin, single, 11.91 mm diameter — 50 mm length (M323.B91, Metav IndustryLine) Test pin, single, 11.91 mm diameter for workshop gauging and end‑measure verification in production and maintenance environments. Workshop‑grade construction Diameter 11.91 mm precision 50 mm length for fixture checks Tolerance ±0.002 mm Consistent repeatability for everyday inspection The compact pin offers a repeatable reference thanks to its ±0.002 mm manufacturing tolerance, which corresponds to a deviation of just two micrometres; this level of accuracy supports reliable end‑measure checks and reduces rework in component inspection. Where process stability matters, the reproducible seating and minimal runout ensure that comparative measurements and go/no‑go routines yield consistent results with each cycle. Robust workshop design that handles practical use Constructed in special steel and delivered as a single workshop‑grade gauge, the component is designed for practical handling and frequent use on the shop floor. The 50 mm overall length provides a convenient reach for fixture and bore checks without becoming unwieldy, while the compact diameter keeps the pin suitable for tight locating bores and gauge setups. Durability and ease of handling lower downtime for routine inspection tasks. Integrates into inspection workflows and fixtures The pin is intended as a simple, dependable datum in assembly, verification and jigs; its standardised size aids interchangeability between fixtures and common measuring tools. Marked with its SKU for traceability, the item supports organised inventory and quick replacement in calibrated inspection benches, enabling teams to maintain throughput without complex setup changes while retaining measurement confidence. Order the M323.B91 test pin through Metav Werkzeuge for dependable workshop gauging; contact our consultants in Emmerich for tailored advice and application support. Technical data Article number: M323.B91 GTIN: 4061905065743 Brand: Metav IndustryLine Facts Diameter: 11.91 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: special steel Workshop version Single test pin Category: measuring pins FAQ What tolerance is specified for this test pin? The M323.B91 test pin is manufactured to a tolerance of ±0.002 mm, providing micrometre‑level repeatability for end‑measure checks. Which material is used for the pin? The pin is made from special steel, chosen for its wear resistance and suitability for repeated locating and inspection operations. Is this pin suitable for fixture and bore checking? Yes — the 11.91 mm diameter and 50 mm length make the pin well suited to fixture locating, bore verification and assembly gauging tasks. How is the item supplied and identified? The product is supplied as a single test pin and is identified by SKU M323.B91 and GTIN 4061905065743 for traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.92mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact, workshop‑ready measuring component that combines tight tolerance and robust construction for reliable end‑dimension verification; order or request further advice via Metav Werkzeuge for professional procurement and technical guidance. M323.B92 Gauge Pin – 11.92 mm Diameter, 50 mm Length (Metav IndustryLine) The M323.B92 gauge pin is a single, precision test pin designed for end‑dimension checking and fixture alignment in workshop metrology. Workshop version for robust daily use Diameter 11.92 mm for precise fit Length 50 mm, hardened special steel Tolerance ±0.002 mm for high precision Accuracy that protects process quality This gauge pin is manufactured to a tight nominal tolerance of ±0.002 mm, making it suitable where small deviations can disrupt assembly or functional performance. The small diameter of 11.92 mm and the short, rigid length produce minimal deflection during insertion, which supports high repeatability in go/no‑go checks and end‑dimension verification. For production environments that run serial checks or set up fixtures, the measurable benefit is lower scrap rates and fewer rework cycles thanks to dependable dimensional reference. Built for the workshop — durable and easy to handle Engineered as a workshop version, the pin combines a compact profile with a 50 mm overall length that suits many standard locating and checking applications. The component is made from special steel, chosen for wear resistance under frequent contact; this ensures sustained geometric integrity in daily use. The modest mass (0.1 kg) and straightforward single‑piece design simplify handling and insertion into test nests or alignment jigs, reducing set‑up time without compromising the stability required for repeatable measurements. Integrates smoothly into inspection routines As a dedicated measuring element, the gauge pin functions as a simple reference for end‑dimension checks, fixture set‑up and pass/fail testing. The clear specification and compact dimensions enable quick selection when matching pin size to bore or groove dimensions. The item is traceable by its SKU and GTIN for inventory control and procurement; the M323.B92 gauge pin therefore fits both reactive workshop checks and planned quality‑assurance sequences where documentation and consistent part identity matter. Contact Metav Werkzeuge for procurement and technical advice on selecting the right gauge pin for workshop or fixture use — our Emmerich team supports specification checks and order handling. Technical Data Article number: M323.B92 GTIN: 4061905065750 Label: Prüfstift, einzeln, 11,92 mm Länge 50 mm Core specifications Diameter: 11.92 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Features / Materials Workshop version Material: Special steel Single test pin design FAQ What inspection tasks is this gauge pin intended for? The M323.B92 gauge pin is intended for end‑dimension verification, fixture alignment and simple go/no‑go checks where a precise reference diameter is required. Can the pin be used in alignment jigs and locating fixtures? Yes, the single‑piece design and 11.92 mm diameter make the M323.B92 suitable for locating, alignment and fixture set‑up applications in workshop environments. How does the stated tolerance affect measurement certainty? With a tolerance of ±0.002 mm, the gauge pin provides a stable reference that reduces uncertainty in repetitive insertion checks and helps maintain consistent assembly tolerances. Is the material suitable for repeated contact with steel components? The M323.B92 is made from special steel and is designed for durability under frequent contact; it offers good wear resistance for routine workshop use. How should the gauge pin be stored to retain accuracy? Store the pin in a dry, clean area away from heavy impact; keep it protected from contaminants and mechanical shocks to preserve the dimensional accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.93mm Test Pin Length 50mm Workshop Version, Precision ±0.002mm - Metav IndustryLine
Precise workshop-grade gauge pin with 11.93 mm diameter and 50 mm length, offering ±0.002 mm accuracy in a robust special steel construction. Designed for repeatable dimensional checks and supplied in a protective transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.B93 gauge pin – 11.93 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.B93 is a workshop-grade test pin for dimensional verification and go/no-go checks in production, inspection and assembly settings. Workshop-grade execution Diameter 11.93 mm, length 50 mm Accuracy ±0.002 mm Supplied in protective transport case Precision that lowers rejection rates The pin is manufactured to a tight ±0.002 mm tolerance, providing measurable improvements in process control and fewer false rejects on the production line. As a hardened, single-piece test element, it gives consistent repeatability during successive checks, so measurement personnel can rely on stable results even under frequent use. The compact geometry and precise diameter make it suitable for pinpoint verification tasks where microscopic deviations affect assembly quality. Built for daily workshop use and straightforward handling With a workshop-grade design and special steel construction, this test pin stands up to routine handling, quick fits and bench checks. The 50 mm length and smooth surface simplify insertion and withdrawal from gauges or bores, reducing time spent aligning items for inspection. Supplied in a protective transport case, the component remains protected from contamination and damage between shifts, which helps preserve its calibrated condition and extends service life. Integration into inspection routines and documentation The component integrates easily into existing inspection jigs and hand-held comparators, enabling quick pass/fail decisions without extensive setup. Traceable identification (SKU and GTIN included in the technical data) allows straightforward record keeping for quality systems. Lightweight at approximately 0.1 kg and manufactured for workshop environments, the pin supports efficient spot checks and regular sampling plans while maintaining measurement integrity. Contact Metav Werkzeuge in Emmerich for advice on workshop measurement solutions and to arrange supply of the M323.B93 workshop-grade gauge pin Technical Data Article number: M323.B93 GTIN: 4061905065767 Label: Gauge pin, single, 11.93 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 11.93 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Measurement range min/max: 11.93 mm / 11.93 mm Special features Workshop-grade execution Material: special steel Supplied in protective transport case Single piece (individual pin) FAQ What tolerance does this gauge pin provide? The M323.B93 gauge pin is manufactured to a tolerance of ±0.002 mm, suitable for high-precision workshop checks and repeatable dimensional verification. Which materials suit inspection with this test pin? The test pin itself is made from special steel for durability; it is used to check dimensions of components made from metals and common engineering materials where a hardened verification element is required. How is the pin supplied and protected during transport? Delivery is in a protective transport case to prevent damage and contamination between uses, preserving the pin’s condition for reliable measurements. Can this pin be used for both production checks and laboratory sampling? Yes, the robust construction and fine tolerance make it appropriate for regular production spot checks and controlled sampling in quality inspection areas. Is the component traceable for quality records? Identification details such as SKU and GTIN are provided in the technical data, enabling straightforward documentation for quality systems and traceability Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.94mm Gauge Pin Precision Steel 50mm Workshop Version - Metav IndustryLine
The combination of a Ø 11.94 mm nominal size, ±0.002 mm tolerance and a compact 50 mm length delivers repeatable end‑dimension checks with minimal setup time; benefit from robust workshop construction and consistent inspection results. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.B94 — inspection gauge pin, Ø 11.94 mm, 50 mm length (Metav IndustryLine) A Test pin M323.B94 designed for precise end‑dimension checks and quality control in workshop and inspection environments. High accuracy ±0.002 mm Diameter Ø 11.94 mm Length 50 mm for compact set-ups Made from special steel Workshop version for robust use Reliable dimensional control for fast inspection The gauge pin is engineered for end‑dimension verification where repeatability matters. With a stated tolerance of ±0.002 mm, the pin allows confident go/no‑go or comparative checks against master gauges and fixtures. This degree of precision reduces uncertainty in acceptance testing, shortens inspection cycles and lowers the risk of downstream rework. The nominal 11.94 mm dimension is ideal for fine tolerancing in component seating, bore gauging and fixture calibration. Robust construction suited to workshop routines Manufactured from special steel, this inspection pin offers a balance of surface stability and wear resistance appropriate to daily use. The compact 50 mm length and modest weight (0.1 kg) keep handling straightforward while preserving stiffness during seated measurements. As a workshop version, the design tolerates routine handling and is compatible with bench clamps or carrier plates used in assembly and testing environments, enabling durable service under regular throughput conditions. Integration into quality workflows and fixtures Designed as a simple but precise metrology element, the pin supports rapid integration into inspection jigs and dimensional control stations. The solid construction and tight tolerance make it suitable for comparative measurements and batch sampling as part of statistical process control. Labelling and identifiers (SKU M323.B94, GTIN 4061905066238) simplify inventory tracking and document control within quality systems, helping to maintain traceability across production runs. Practical handling, storage and usage notes For best long‑term performance, handle the pin with care to avoid impact or abrasion to the measuring surfaces and store it protected from corrosive environments. Cleaning with a lint‑free cloth and light machining oil after use preserves the contact faces and supports consistent readings. The compact form factor makes the element simple to place into dedicated holders for repeatable alignment during multi‑part inspection cycles. For a reliable workshop test pin tailored to end‑dimension control, contact Metav Werkzeuge to discuss availability of the M323.B94 and delivery options from Emmerich. Technical data SKU: M323.B94 GTIN: 4061905066238 Brand: Metav IndustryLine Core measurements Nominal diameter: 11.94 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.1 kg Materials & special features Material: Special steel Version: Workshop execution Intended application: End‑dimension checks and inspection FAQ What tolerance does the M323.B94 deliver? The M323.B94 test pin is specified with a tolerance of ±0.002 mm, suitable for precise end‑dimension inspection tasks. Which nominal size and length apply to this gauge pin? This inspection pin has a nominal diameter of 11.94 mm and a length of 50 mm, designed for compact fixture use. What material is used for the inspection pin? The pin is manufactured from special steel, selected for stability and wear resistance in workshop conditions. Is the M323.B94 suitable for fixture and jig integration? Yes, the compact dimensions and robust construction make the pin well suited for inclusion in inspection jigs and comparative fixtures. How is the product identified for stock and traceability? Identification is provided via SKU M323.B94 and GTIN 4061905066238 for inventory control and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.95mm Gauge Pin, 50mm Length Workshop Version, Special Steel, ±0.002mm - Metav IndustryLine
Take advantage of the combination of high repeatability, workshop-ready robustness and a compact form factor for efficient end‑dimension checks. Order the gauge pin directly via Metav Werkzeuge or consult our advisers for specification support and delivery guidance. Gauge pin, single, 11.95 mm diameter — 50 mm length (Metav IndustryLine) The Gauge pin, single, 11.95 mm, length 50 mm is a workshop‑grade measuring pin for precise end‑dimension verification and plug‑fit control in production and inspection tasks. Workshop version for robust daily use Diameter 11.95 mm for end‑dimension control Length 50 mm suited to plug and gap checks Tolerance ±0.002 mm for high repeatability Precision for end‑dimension control that reduces rework The single measuring pin is manufactured from special steel and finished for a consistent fit; this delivers repeatable results when checking bores, plug fits or mating parts. With a nominal diameter of 11.95 mm and an accuracy of ±0.002 mm, the pin supports tight tolerance control that lowers scrap rates and shortens inspection time. Classified as a Micro measuring instrument (measuring range 10–100 mm), this compact gauge is tailored to fine mechanical work where short jaw lengths and low distortion are advantageous. Built for workshop reliability and straightforward handling This workshop execution combines a short 50 mm length with a durable surface to withstand everyday use on the shop floor. The moderate mass and ergonomic proportions make single‑handed placement simple, speeding up repetitive checks during assembly or quality control. The use of special steel ensures wear resistance and dimensional stability, so calibration intervals are extended and measurement drift is reduced. The straightforward geometry avoids complex handling, enabling faster throughput in routine inspection tasks. Practical applications and how the pin integrates into quality workflows Ideal for end‑dimension checks, plug‑gauge comparisons and reference stacking, the pin provides a reliable physical standard for quick go/no‑go assessments or for setting up comparator fixtures. In automated or semi‑automated inspection stations, these pins act as fixed references for alignment and runout checks. Specifying a high‑accuracy pin such as this one helps to maintain process capability and provides clear, measurable evidence for production tolerance conformance — an immediate operational benefit in serial manufacturing environments. For procurement or application advice on the Metav IndustryLine gauge pin M323.B95, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for detailed consultation and rapid supply. Technical data SKU: M323.B95 GTIN: 4061905063541 Brand: Metav IndustryLine Material: Special steel Weight: 0.1 kg Label: Gauge pin, single, 11.95 mm length 50 mm Facts Nominal diameter: 11.95 mm Length: 50 mm Measuring range: 11.95 mm Measuring range min/max: 11.95 / 11.95 mm Accuracy / deviation: ±0.002 mm Special features Workshop execution Classified: Micro (measuring range 10–100 mm) Suitable for end‑dimension and plug‑fit checks Single pin format for targeted measurements FAQ What is the intended use of this gauge pin? The gauge pin is intended for end‑dimension verification, plug‑fit testing and quick go/no‑go assessments in production and inspection environments. Is the nominal diameter 11.95 mm suitable for standard plug checks? Yes, the 11.95 mm nominal diameter provides a precise reference for plug and gap tests and is specified for controlled end‑dimension checks. What level of accuracy can be expected from this pin? The measuring pin offers an accuracy of ±0.002 mm, ensuring high repeatability for routine quality control tasks. What material is the pin made from and does that affect wear? Manufactured from special steel, the pin is engineered for wear resistance and dimensional stability in workshop use. Can the pin be used as a reference in fixture set‑up or automated stations? Yes, the single gauge pin is suitable as a fixed reference for alignment and fixture set‑up in semi‑automated or manual inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.96mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Milling and inspection tasks benefit from the combination of high geometric accuracy, compact handling and robust special-steel construction for dependable end measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.B96 — 11.96 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.B96 for precise end-measurements and small-part inspection, designed as a workshop-grade single inspection pin for repeatable plugging and checking tasks. Diameter 11.96 mm for precise end measurements Length 50 mm, compact and easily handled Special steel construction for wear resistance Tolerance ±0.002 mm for high repeatability Precision that reduces uncertainty in end checks The gauge pin is manufactured to a nominal diameter of 11.96 mm with a declared tolerance of ±0.002 mm, providing measurement confidence for tight-fit inspections and go/no-go verifications. This level of geometric accuracy reduces rework by ensuring that dimensional checks are both repeatable and traceable. Where a fixed-diameter reference or plug is required, a single, high-accuracy inspection pin replaces iterative trial fits and accelerates in-process decisions, supporting measurable improvements in throughput and quality control. Durable workshop design for frequent use Constructed from special steel, this inspection pin is optimised for workshop conditions where durability and surface integrity matter. The workshop version specification indicates a finish and hardness balance that resists fretting and maintains gauge form under repeated insertion cycles. The robust material choice also simplifies handling requirements: less frequent replacement is needed, and wear patterns remain predictable, which helps planners schedule maintenance and replacement without unexpected downtime. Compact format for tight spaces and precise alignment With a length of 50 mm the pin offers a compact footprint that is convenient for jigs, fixtures and confined inspection stations. The short, stiff shank minimises deflection during insertion, improving measurement reliability for end-face and bore-entry checks. As a single plug gauge, it excels where a precise nominal diameter is needed for alignment, fixture set-up or final-pass verification; the compact geometry makes it easy to position, clamp or integrate into handheld or bench-based routines without elaborate fixturing. Practical integration into quality workflows The inspection pin supports streamlined inspection processes: its nominal size and documented tolerance simplify pass/fail criteria in quality plans and inspection sheets. Traceable identifiers such as GTIN and the SKU are provided for inventory control, while the simple geometry makes the pin compatible with mechanical gauges and optical measurement devices. Sourcing through an experienced partner ensures a consistent supply chain and clear provenance for audit purposes, supporting shopfloor planners and quality engineers in meeting inspection standards efficiently. Contact Metav Werkzeuge for availability and technical guidance on the M323.B96 gauge pin — email info@metav-werkzeuge.com or call +49 2822 7131930 for bespoke advice and fast delivery from Emmerich Technical data Article number: M323.B96 GTIN: 4061905063558 Weight: 0.1 kg Material: Special steel Core figures Diameter: 11.96 mm Length: 50 mm Tolerance: ±0.002 mm Mass: 0.1 kg Special features Workshop version Single gauge pin for end measurements Suitable for plug/fit inspection and alignment FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin M323.B96 has a nominal diameter of 11.96 mm with a tolerance of ±0.002 mm. Which materials is the pin made from and how does that affect wear? The inspection pin is produced from special steel; this material choice improves wear resistance and preserves the gauge form under frequent use. For which inspection tasks is this pin best suited? This single plug gauge is intended for end-measurements, fit checks and alignment tasks in workshop and inspection environments. How can the M323.B96 be referenced in inventory and ordering? Use the GTIN 4061905063558 or article number M323.B96 to ensure correct identification and replenishment in purchasing systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.97mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise end‑dimension control with a robust 11.97 mm nominal diameter and ±0.002 mm tolerance in a compact 50 mm length. Combine workshop‑grade construction and special steel for repeatable contact and long service life — order directly via Metav Werkzeuge or consult our specialists for application guidance. Gauge pin M323.B97 — single test gauge, 11.97 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.B97 offers a dedicated workshop solution for end‑dimension checks and bore verification in production and inspection areas Workshop-grade construction 11.97 mm nominal diameter Length 50 mm for stable contact High accuracy ±0.002 mm Consistent end‑dimension verification that keeps production running The compact test pin gives a reliable reference for verifying final dimensions on mating parts and bores. With a nominal diameter of 11.97 mm and a tight tolerance of ±0.002 mm, the pin supports precise go/no‑go checks and assembly trials, reducing rework and machine downtime. The short overall length of 50 mm ensures a stable seated contact point, improving repeatability during batch inspections and making the pin suitable for routine production control. Robust workshop design for everyday handling and durability Designed as a workshop‑grade item, the test pin withstands frequent use in shop environments without compromising accuracy. Manufactured from special steel, the component provides wear resistance at contact zones and stable dimensional retention over time. The single‑piece configuration simplifies traceability and inventory management while delivering the tactile feedback expected in mechanical gauging tasks. Accuracy and what ±0.002 mm means in practice An accuracy specification of ±0.002 mm denotes narrow variation margins for the measurement reference, which translates directly into fewer false rejects and more consistent assembly fits. For typical production and quality control contexts, this level of precision allows reliable verification of mating tolerances and ensures that calibrated fixtures and checking jigs remain aligned with design intent. The numerical clarity supports decisions based on measurable criteria rather than approximation. Easy integration into inspection workflows The compact form factor and standard diameter make the pin straightforward to incorporate into existing inspection stations, plug gauges and fixture set‑ups. Its balanced mass and dimensioning allow rapid handling and repeat checks, so cycle times remain short while maintaining traceable measurement outcomes. For parts requiring final verification before shipment or assembly, this type of pin becomes an expedient tool for securing consistent quality. Secure precise end‑dimension verification with Metav IndustryLine gauge pins — contact Metav Werkzeuge in Emmerich for availability, delivery options and tailored application advice (info@metav-werkzeuge.com · +49 2822 7131930) Technical data Article number: M323.B97 GTIN: 4061905063565 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 11.97 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features / Versions Workshop‑grade construction Material: special steel Single piece test pin Suitable for end‑dimension and bore checks FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 11.97 mm with a tolerance of ±0.002 mm, providing a precise reference for dimensional checks. Can this test pin be used for routine production checks? Yes, the workshop‑grade construction and compact 50 mm length make the test pin well suited to frequent production and assembly verification tasks. What material is the pin made from and why does it matter? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability under repeated contact, which helps maintain measurement consistency. Is the pin supplied as a single piece or in sets? The product is supplied as a single test pin, simplifying traceability and inventory handling for specific diameter checks. Which inspection tasks is this pin optimised for? It is optimised for end‑dimension verification, bore checks and plug gauge applications where a stable contact point and tight tolerance control are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.98mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precision and repeatability thanks to the ground 11.98 mm diameter and ±0.002 mm tolerance, combined with a robust 50 mm length in specialist steel for reliable end‑dimension checks; order the test pin directly via Metav Werkzeuge or consult the sales team for further application advice Gauge pin M323.B98 — single precision test pin, 11.98 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.B98 is a single, cylindrical test pin designed for end‑dimension verification and go/no‑go inspection tasks in workshop and assembly environments Precision tolerance ±0.002 mm Diameter 11.98 mm, ground finish 50 mm solid test pin length Delivered in protective transport box Repeatable accuracy for routine inspection This single cylindrical test pin delivers repeatable measurement performance thanks to its very fine manufacturing tolerance of ±0.002 mm. The combination of a ground diameter and a compact, solid design reduces run‑out and misalignment during seating, which shortens inspection cycles and lowers rework rates. The construction in special steel gives dimensional stability under typical workshop handling, turning individual checks into consistent quality evidence for production decision‑making. Compact geometry for confined and production use With a nominal diameter of 11.98 mm and an overall length of 50 mm, the test pin is tailored to confined inspection points and tight fixture interfaces. The small footprint and single‑piece construction make handling straightforward and minimise orientation errors when inserted into bores or jigs. This geometry supports efficient inline checks and makes the component suitable for both spot checks and repeated assembly controls where ergonomic handling and rapid positioning accelerate throughput. Robust preparation and transport for the workshop Items are supplied ready for immediate use and packaged for workshop environments in a protective transport box, reducing the risk of damage in transit and simplifying storage on the shop floor. The solid material choice and workshop version finish are aimed at hard‑wearing everyday use; the compact form factor also helps to keep the test pin accessible at inspection benches without occupying excessive space. This practical approach supports steady, dependable inspection routines across shifts. Choose the Metav IndustryLine gauge pin for dependable end‑dimension checks — contact Metav Werkzeuge for purchasing guidance and technical clarification at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.B98 GTIN: 4061905063572 Name: Gauge pin, single, 11.98 mm, length 50 mm Numbers / Core technical data Diameter: 11.98 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Single test pin (individual) Workshop version Protective transport box for delivery FAQ What level of accuracy can be expected from this test pin? The M323.B98 gauge pin is manufactured to a tolerance of ±0.002 mm, providing very fine control for end‑dimension checks in workshop inspections. Is the material specified for the pin suitable for routine workshop use? Yes — the pin is made from special steel, offering the dimensional stability and surface durability expected for regular handling and insertion into jigs or measuring fixtures. Does the delivery include protective packaging? Delivery for the M323.B98 includes a protective transport box to reduce the risk of damage during shipment and store the pin safely on the shop floor. Is a calibration certificate supplied with the pin? No calibration information is specified for this item; there is no indication of an ISO 17025 calibration certificate being included. Which applications is this gauge pin intended for? The test pin is intended for end‑dimension verification, go/no‑go checks and fixture alignment tasks where a compact, accurate cylindrical master is required Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.99mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of workshop‑grade robustness, ±0.002 mm repeatability and the special steel construction for dependable end‑measure and fit tests; order directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single 11.99 mm — Workshop‑grade plug gauge, special steel, ±0.002 mm (Metav IndustryLine) The gauge pin, single 11.99 mm provides a compact, workshop‑ready solution for end‑measure verification and fit testing in gauges, fixtures and assembly controls Workshop version for robust daily use Diameter 11.99 mm, tolerance ±0.002 mm Made from special steel for wear resistance Supplied in protective transport case Precise fit and end‑measure verification that reduces rework A compact plug for dimension checks, the gauge pin delivers high repeatability thanks to its declared ±0.002 mm variation. With a nominal diameter of 11.99 mm, this test pin is suited to tight clearance and end‑measure checks where small deviations matter. The controlled tolerance offers a reliable pass/fail criterion during assembly and inspection routines, translating directly into fewer rejects and less rework on the shop floor. The pin’s geometry supports quick insertion into bores and gauges, enabling rapid go/no‑go decisions without complex setup. Built for everyday workshop use to keep production moving Engineered as a workshop‑grade instrument, the pin is machined from special steel to withstand repeated handling and contact with mating parts. The 50 mm overall length balances reach and rigidity for common fixture depths, while the supplied protective transport case reduces the risk of surface damage during storage and transit. These practical choices reduce downtime and extend service intervals, making the component a pragmatic addition to inspection kits in maintenance departments and small production lines. Simple integration, traceability and suitability for micro‑scale measurements Classified within the Micro class (10–100 mm) of inspection tools, this plug gauge fits applications that demand compactness without compromising on accuracy. With a mass of 0.1 kg and a nominal length 50 mm, the pin is easy to handle and store alongside hand tools. Identification is straightforward for procurement and traceability: SKU M323.B99 and GTIN 4061905063589 support repeat orders and inventory control. The combination of compact form, robust material and tight tolerance makes the pin a dependable element of routine quality assurance. Contact Metav Werkzeuge for tailored application advice and secure supply of Metav IndustryLine workshop‑grade gauge pins with proven ±0.002 mm performance Technical data SKU: M323.B99 GTIN: 4061905063589 Manufacturer: Metav IndustryLine Facts Diameter: 11.99 mm Length: 50 mm Tolerance/variation: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Supplied in protective transport case Category: Gauge pins (Messstifte) FAQ What level of accuracy can be expected from this gauge pin? The gauge pin offers a declared variation of ±0.002 mm, making it suitable for fine fit and end‑measure checks where tight tolerances are required; see SKU M323.B99 for ordering. Which materials is the pin made from and how does that affect wear? Machined from special steel, the pin balances hardness and toughness for improved wear resistance in daily inspection tasks, helping to maintain dimensional integrity over repeated use. Is this test pin suitable for deep bore checks? With a length of 50 mm and a compact diameter of 11.99 mm, the pin is designed for common bore depths and fixture checks typical in workshop inspection and assembly routines. Does the product include a protective case for transport? Yes, the item is supplied in a protective transport case to prevent damage during storage and transit, ensuring surface quality at the point of use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11.9mm Gauge Pin 50mm Length Workshop Version, Precision ±0.002mm - Metav IndustryLine
Combining 11.9 mm diameter, 50 mm length and workshop‑grade special steel construction, this test pin achieves repeatable end measurements with a verified runout of ±0.002 mm; order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin, single, 11.9 mm Ø, 50 mm length — Metav IndustryLine A Test pin, single, 11.9 mm Ø, 50 mm length designed for precise end‑measurement and fixture verification in workshop and inspection jig environments Workshop‑grade construction Diameter precisely 11.9 mm Length 50 mm for deep checks Special steel for dimensional stability Consistent measurement accuracy for repeatable production The pin delivers a ±0.002 mm runout that supports reproducible end‑measurements and reduces the need for rework. In production and quality control contexts, a small tolerance directly translates into fewer scrapped parts and faster go/no‑go decisions. The compact geometry and fixed diameter allow secure seating in gauges and fixture bores, so measurement variance caused by locating errors is minimised. By choosing a component with defined mechanical behaviour, process capability and inspection throughput can be improved without complex retrofit work. Practical design for workshop workflows and fixtures Engineered as a workshop version, the probe length of 50 mm gives access to deeper locating points while remaining easy to handle and position. The combination of compact mass and robust form factor supports rapid manual use during setup checks, while still being suitable for light automated fixtures. The single‑piece configuration simplifies stocking and replacement logistics in busy shops; a standardised dimension means fewer bespoke adapters and quicker exchange when wear occurs. As a result, fixture verification becomes a straightforward, low‑risk step in the assembly or machining cycle. Material selection that prioritises dimensional stability Manufactured from special steel, the pin is specified to hold its geometry under normal workshop loads and temperature swings common at the machine table. The choice of material emphasises dimensional stability and resistance to everyday mechanical wear, contributing to long service intervals and predictable performance. For users who require reliable seating and repeatability rather than decorative finishes, this construction offers the best balance between durability and handling. Typical uses and integration into inspection routines The pin is intended for end‑measurements, jig and fixture checks, and quick verification of bore seating; it integrates with common locating systems and check gauges. In inspection benches it serves as a precise datum or contact element for comparing component ends and establishing reproducible reference points. Using a standardised test pin simplifies documentation and makes layout planning easier across multiple machines or workstations. Overall, the pin supports a pragmatic approach to reducing measurement uncertainty and increasing confidence in inspection results. For reliable end‑measurement and fixture checks, request the Metav IndustryLine test pin M323.B90 from Metav Werkzeuge for stock availability and tailored technical advice Technical Data Article number: M323.B90 GTIN: 4061905065736 Label: Test pin, single, 11.9 mm diameter, 50 mm length Manufacturer: Metav IndustryLine ECLASS: 21170231 Core technical data Diameter: 11.9 mm Length: 50 mm Tolerance / runout: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Single test pin SKU: M323.B90 FAQ What tolerance can be expected from this test pin? The Test pin, single, 11.9 mm Ø, 50 mm length provides a runout tolerance of ±0.002 mm, suitable for high‑repeatability end‑measurements and fixture checks. Is this pin suitable for use in jigs and gauges? Yes. The 50 mm length and 11.9 mm diameter are designed for secure seating in jigs, gauges and fixture locating points; the workshop‑grade construction supports frequent handling. Which material is used and what are the benefits? The pin is made from special steel, selected for dimensional stability and wear resistance under normal workshop conditions, which helps preserve measurement accuracy over time. How can the product be identified for ordering or stock purposes? This item is listed as SKU M323.B90 with GTIN 4061905065736 and is part of the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
11mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise repeatability and robust workshop construction: the 11.00 mm gauge pin delivers ±0.002 mm positional certainty with a compact 50 mm length, supplied in a protective transport case for secure handling — order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.B00 — Single gauge pin, Ø 11.00 mm, length 50 mm (Metav IndustryLine) the Test pin, single, Ø 11.00 mm, length 50 mm is a workshop-grade gauge pin designed for reliable end‑measure checks and alignment tasks in fine mechanical and assembly environments Workshop-grade construction Precision ±0.002 mm Supplied in transport case Accuracy where repeatability matters The compact gauge pin is manufactured for high repeatability, with a stated positional variation of ±0.002 mm, which places it well within fine workshop tolerances. This level of precision reduces setup variation when used as an end gauge or locating pin, helping to shorten inspection cycles and improve process stability. The small diameter and short length limit bending moments, so readings remain consistent even under manual handling. Explaining the figure: ±0.002 mm denotes the maximal permitted deviation under typical workshop conditions, giving a clear, verifiable basis for quality control decisions. Durable workshop design for everyday use Built in a workshop execution and made from special steel, the pin combines wear resistance with dimensional stability. The 50 mm overall length provides sufficient engagement for secure seating while minimising leverage that can distort results. Delivered in a protective transport case, the item arrives ready for safe storage and transport. The modest mass (approx. 0.1 kg) aids practical handling and contributes to a reassuring feel during repetitive positioning tasks, without adding unnecessary bulk to tool kits or inspection benches. Practical applications and handling benefits Intended for end‑measure verification and location duties in jigs, fixtures and assembly checks, the gauge pin simplifies go/no‑go evaluations and alignment procedures. In production contexts where small, repeatable accuracy is required, the pin functions as a straightforward reference standard for mating bores, locators and gauge blocks. The compact format is classified in the micro range (10–100 mm), making it particularly suited to fine mechanical work, small components and watch‑type parts where space and stiffness are equally important. Choose the Metav IndustryLine gauge pin for consistent end‑measure control — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for procurement and technical advice. Technical data Article number: M323.B00 GTIN: 4061905065606 EClass: 21170231 Label: Prüfstift, einzeln, 11,00 mm Länge 50 mm Facts Diameter: 11.00 mm Length: 50 mm Mass: 0.1 kg Accuracy (variation): ±0.002 mm Special features Material: Special steel Version: Workshop execution Packaging: Supplied in transport case Application hint: End‑measure checks / alignment FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.B00 offers a positional variation of ±0.002 mm, making it suitable for fine workshop tolerances where repeatable end‑measure checks are required. Is the pin suitable for use as a locating dowel in fixtures? Yes, the workshop‑grade construction and 50 mm length of this test pin support reliable locating duties and alignment in jigs and fixtures, with the compact form reducing bending influence. How is the test pin supplied and protected during transport? The M323.B00 is supplied in a protective transport case to prevent damage and maintain dimensional integrity during handling and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12,01- 13,00mm Messstift-Sätze, Werkstatt-Ausführung, ± 0,004 mm
- aus Spezial-Stahl Werkstatt-Ausführung, Länge 50 mm Genauigkeit < ± 0,004 mm im Behältnis/KastenTechnische Daten- Messbereich: 12,01- 13,00mm- Stufung: 0,01mm- Anzahl/Satz: 100
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com