Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
12.01mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of precise tolerance, robust workshop construction and compact length for dependable inspection work. The clear diameter of 12.01 mm and the fine ±0.002 mm tolerance make this tool suitable for repeatable gauging tasks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if additional information is required. Gauge pin, single — 12.01 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin, single, 12.01 mm designed as a hardened datum for accurate bore checking and end‑measurement tasks in workshop metrology. 12.01 mm diameter 50 mm length Tolerance ±0.002 mm Workshop execution Repeatable inspection with micrometre-level tolerance The compact design provides a consistent datum for go/no‑go checks and comparative gauging tasks. Manufactured for high repeatability, this gauge pin features a defined diameter of 12.01 mm and a declared tolerance of ±0.002 mm, which supports reliable part verification and reduces downstream rework. The narrow tolerance converts directly into measurable process stability, so inspection steps become a dependable part of the production chain rather than a variable. Robust materials and workshop-ready construction Made from special steel for wear resistance and dimensional stability, the pin resists deformation under typical handling and fixture loading. The 50 mm length gives sufficient engagement for many bore depths while remaining easy to handle on the shop floor. The workshop version finish balances hardness and serviceability, ensuring long life in daily use and straightforward cleaning between shift changes to preserve measurement integrity. Practical use in production and assembly control The pin suits inline inspection, fixture calibration and quick functional checks during assembly. Its compact form and narrow tolerance help to verify critical bores and mating features during incoming inspection or final assembly checks. Integration into existing gauging sets or shadow boards is straightforward, and traceable marking such as the SKU allows consistent inventory and replacement planning in the quality workflow. Select the Metav IndustryLine gauge pin M323.C01 for consistent bore verification and contact Metav Werkzeuge for precise delivery from Emmerich and expert advice on integration into existing inspection procedures Technical data Article number: M323.C01 GTIN: 4061905064326 Label: Prüfstift, einzeln, 12,01 mm Länge 50 mm Core dimensions Diameter: 12.01 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & special features Material: Special steel Workshop execution Single gauge pin, hardened datum FAQ Is this gauge pin suitable for routine bore checks in the workshop? The Metav IndustryLine gauge pin M323.C01 is intended for routine bore verification and assembly checks thanks to its workshop execution and fine tolerance of ±0.002 mm. What material is the pin made from and how durable is it? The pin is made from special steel, providing a balance of hardness and wear resistance for sustained use in inspection routines. Can the pin be used as a datum in fixture setup? Yes, the 50 mm length and precise diameter make the pin suitable as a hardened datum in many fixture and alignment tasks. How is the product identified for inventory and traceability? Identification is possible via the article number M323.C01 and GTIN 4061905064326 for straightforward inventory control Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.02mm Test Pin Length 50mm Workshop Version, Special Steel in Case - Metav IndustryLine
Take advantage of precise end-measurement performance, robust workshop construction and straightforward handling for reliable inspection routines; the combination of 12.02 mm diameter, ±0.002 mm accuracy and a 50 mm length supports consistent go/no‑go checks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 12.02 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin, single, 12.02 mm diameter, 50 mm length is a workshop-grade cylindrical reference designed for end measurements, pin gauging and simple interchange tests in production and maintenance environments. Workshop version for everyday use Diameter 12.02 mm with ±0.002 mm accuracy Length 50 mm for end-measurements Supplied in transport case Repeatable, verifiable end‑measurements for inspection workflows A compact cylindrical reference delivers measurable benefits in process control. The 12.02 mm diameter with an accuracy of ±0.002 mm provides a reliable basis for quick go/no‑go checks and comparative measurements on production lines. Using a stable, single‑diameter gauge pin reduces setup time for checking bores and fit tolerances, so inspection cycles run more efficiently and non‑value time is minimised. Robust design that withstands workshop conditions Built as a workshop version from special steel, this measuring pin is engineered for frequent handling and routine use. The 50 mm shank gives sufficient mass to avoid accidental bending during short measurements while remaining easy to position by hand. The construction focuses on wear resistance and repeatability, supporting durable service life in busy maintenance and fabrication areas where tools are handled often. Simple integration into existing tool sets and fixtures The single‑piece gauge pin is straightforward to use alongside existing gauges, jigs and handheld comparators. Its plain cylindrical geometry makes it suitable as a quick reference for bore checks, fixture verification and as a physical standard for comparative measurements. Supplied in a transport case, the pin is protected during storage and transit, ensuring the preserved condition of the reference surface between uses. Contact Metav Werkzeuge today to discuss Metav IndustryLine gauge pins for dependable end‑measurement control and to arrange supply or technical clarification Technical data Article number: M323.C02 SKU: M323.C02 GTIN: 4061905064760 Label: Gauge pin, single, 12.02 mm diameter, length 50 mm Facts Diameter: 12.02 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Delivery: Transport case Category: Gauge pins FAQ What tolerance does this gauge pin offer? The gauge pin provides an accuracy of ±0.002 mm, making it suitable for precise go/no‑go checks and repeatable reference measurements with the Metav IndustryLine gauge pin (SKU M323.C02). Can the gauge pin be used for bore checks and fit verifications? Yes, the single‑diameter design serves as a simple reference for bore checks, fit verifications and quick interchange tests in production and maintenance tasks. What are the dimensions of the pin? The measuring diameter is 12.02 mm and the overall usable length is 50 mm, with a total weight of approximately 0.1 kg. How is the pin delivered and protected? The pin is supplied in a transport case to protect the reference surface during transit and storage, preserving measurement integrity. Is this product suitable for everyday workshop use? The Metav IndustryLine gauge pin is a workshop execution intended for frequent handling, offering robust performance and straightforward integration into routine inspection procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.03mm Test Pin Length 50mm Workshop Finish - Metav IndustryLine
Taking advantage of tight tolerance and robust construction, this gauge pin combines high repeatability (±0.002 mm) with a 12.03 mm diameter and a compact 50 mm length for reliable in‑process checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single Ø 12.03 mm, length 50 mm — Metav IndustryLine workshop version Gauge pin, single Ø 12.03 mm, length 50 mm is a precision ground inspection pin for reference measurements, fit checks and alignment tasks in workshop and production metrology. Precision ground to ±0.002 mm Diameter 12.03 mm, length 50 mm Made from special steel, workshop execution Single-piece design for repeatable reference Consistent inspection from a compact reference The gauge pin delivers measurable repeatability thanks to a declared tolerance of ±0.002 mm, a level of accuracy that supports tight go/no-go fits and fine inspection routines in component production. Machined from special steel, the pin resists wear and preserves its geometry across repeated seating and insertion cycles, which reduces rework and non‑conformances. Where traceable reference dimensions are required on the shop floor, this inspection pin functions as a robust, low‑complexity standard for quick dimensional verification. Practical dimensions that simplify handling and layout With a diameter of 12.03 mm and a length of 50 mm, the test pin is compact yet long enough to engage bore features and locating holes without excess overhang. The modest mass and short profile make it straightforward to seat in fixtures, jigs or test rigs, improving handling ergonomics and reducing measurement variability caused by operator influence. The single‑piece configuration avoids stacking tolerances and makes the item suitable for repetitive checks where consistent contact geometry matters. Integration into production and quality workflows Designed for workshop and light industrial use, this inspection pin serves as a dependable reference in assembly, inspection and setup operations. The hardened surface and precise ground shank support repeatable positioning in fixtures and aid rapid conformity checks during series production. For procurement and inventory control, the part is identifiable by SKU M323.C03 and GTIN 4061905064777, which simplifies traceability within quality documentation and material lists. Contact Metav Werkzeuge for ordering or technical selection support from Emmerich’s metrology specialists Technical Data Article number: M323.C03 GTIN: 4061905064777 SKU: M323.C03 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 12,03 mm Länge 50 mm Facts Diameter: 12.03 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Version: workshop execution Single piece inspection pin Category: gauge pin / test pin Intended use: reference measurement and fit checks FAQ What tolerance is guaranteed for this gauge pin? The specified tolerance for the gauge pin is ±0.002 mm, providing high repeatability for fit and inspection tasks. Is the pin suited for repeated seating in hardened fixtures? Yes, the special steel construction and ground finish make the pin suitable for repeated seating in fixtures used for assembly and inspection. Can this pin be used as a reference for centre‑line alignment in jigs? The 50 mm length and precise shank diameter are suitable for positioning and alignment duties; the pin is commonly applied as a reference element in jigs and test rigs. How is the item identified for stocking and traceability? The item is listed under SKU M323.C03 and GTIN 4061905064777, which supports clear identification in procurement and quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.04mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of tight tolerance (±0.002 mm), special-steel construction and a compact 50 mm length for consistent end-dimension checks. Order the gauge pin directly via Metav Werkzeuge or request advice from our technical consultants. Gauge pin M323.C04 — 12.04 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin designed for precise final-dimension checks and robust workshop use Diameter 12.04 mm precision Tolerance ±0.002 mm accuracy Workshop-grade special steel 50 mm length for final-dimension checks Consistent accuracy for reproducible quality control The compact cylindrical design delivers repeatable contact geometry, with a diameter of 12.04 mm and a verified tolerance of ±0.002 mm, making it suitable for high‑precision gauging and end‑dimension verification. The tight tolerance reduces measurement uncertainty during pass/fail inspections and in assembly checks, enabling straightforward decisions on part conformity. This level of accuracy supports process stability in serial testing and small‑batch production, where reproducibility is essential. Robust material and workshop-ready handling Manufactured from special steel, the pin combines wear resistance with dimensional stability under normal workshop conditions, ensuring a long service life when used for routine gauging. The 50 mm overall length provides a practical balance between reach and rigidity, reducing flex during insertion into bores or features. The workshop execution emphasises durability and straightforward handling for bench and fixture use, while keeping maintenance simple and predictable. Practical application and traceable identification Supplied as a single piece with a clear article reference, the pin is intended primarily for final‑dimension checks and end‑measurements in metalworking setups. Typical applications include bore verification, alignment checks and fixture validation in machine shops. The compact mass also minimises impact on delicate assemblies during inspection. For traceability and procurement, the article is identified by SKU M323.C04 and GTIN 4061905064784, facilitating inventory management and quality documentation. For measurements that demand ±0.002 mm reliability, contact Metav Werkzeuge for availability and technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 — Metav IndustryLine specialists will advise on suitability and supply. Technical data SKU: M323.C04 GTIN: 4061905064784 Label: Prüfstift, einzeln, 12,04 mm Länge 50 mm Manufacturer: Metav IndustryLine Core specifications Diameter: 12.04 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Version: Workshop execution Delivery: Single piece Intended use: Final‑dimension checks / end measurements FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin is manufactured to a nominal diameter of 12.04 mm with a stated tolerance of ±0.002 mm, providing tight control for verification tasks. Is this product suitable for repetitive bore checks in a production environment? Yes, the M323.C04 gauge pin from Metav IndustryLine is designed for routine end‑dimension checks and offers the dimensional stability required for repetitive bore inspections. What material is used and how does it affect durability? The pin is made from special steel, chosen for wear resistance and dimensional stability under typical workshop conditions, which enhances service life during frequent use. How is the product identified for procurement and documentation? The article is listed as SKU M323.C04 and carries GTIN 4061905064784 to support ordering and traceability in inventory or quality systems. Can the pin be used for alignment checks in fixtures? Yes, the 50 mm length and precise diameter make the pin suitable for alignment and fixture validation, where a stable datum and repeatable contact are required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.05mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Taking the combination of measured repeatability, robust workshop design and a special-steel construction provides dependable results for end‑dimension checks; order this precision gauge pin directly via Metav Werkzeuge or consult our specialists for specification advice. Gauge pin M323.C05 — Test pin, 12.05 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin, single item, 12.05 mm diameter and 50 mm length, intended for end‑dimension inspection and routine workshop measurement tasks. Workshop-grade design for daily use High precision ±0.002 mm tolerance Special-steel construction for durability Single gauge pin for targeted inspection Keep production tolerances under control with micrometric repeatability This inspection pin delivers ±0.002 mm repeatability, a tolerance level that supports tight quality criteria in assembly and inspection environments. The nominal diameter of 12.05 mm and a length of 50 mm produce a stable contact surface that translates into reproducible measurements across successive checks. Such dimensional stability reduces scrap rates and rework, improving throughput without adding complexity to existing gauge benches or plug‑gauge fixtures. The emphasis is on measurable benefit: consistent results, fewer stoppages and predictable quality outcomes. Built for workshop conditions and frequent handling Designed as a workshop variant, the component combines practical handling with corrosion‑resistant special steel for extended service life under daily use. The compact geometry and balanced mass (approx. 0.1 kg) make the pin easy to position in bores or alignment jigs while resisting premature wear. The single‑item supply is suitable for targeted inspection points where bespoke checks are required rather than bulk gauge sets. Robust material choice and a simple geometry lower maintenance needs and keep calibration intervals manageable, supporting continuous operation on the shop floor. Simple to incorporate into measurement and assembly routines The pin integrates smoothly into existing verification sequences, from first‑off inspections to in‑process checks and final acceptance trials. Use as a reference mandrel, plug gauge or alignment aid in fixtures that require a reliable datum of 12.05 mm. The compact length of 50 mm minimises bending moment in handheld checks and eases handling in confined setups. Marked traceability (SKU M323.C05) by the manufacturer facilitates inventory control and makes replacement straightforward when pins are rotated through wear cycles. The result is faster decision‑making and fewer interruptions to production flow. For supply and specification advice on the Metav IndustryLine gauge pin (M323.C05), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for a tailored recommendation Technical data Article number: M323.C05 GTIN: 4061905064791 Brand: Metav IndustryLine Label: Gauge pin, single, 12.05 mm diameter, 50 mm length Core specifications Diameter: 12.05 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features Workshop version Material: special steel Single item delivery Application: end‑dimension checks FAQ What is the dimensional tolerance of this gauge pin? The gauge pin from Metav IndustryLine (M323.C05) has a specified tolerance of ±0.002 mm, suitable for precise end‑dimension verification. Which material is used for the pin and what does that mean for durability? The test pin is made from special steel, chosen to provide wear resistance and stable performance under routine workshop use. Can this pin be used as an alignment mandrel in fixtures? Yes, the 12.05 mm diameter and 50 mm length make the pin suitable as an alignment mandrel or plug in many fixture and assembly applications. How is the product supplied and identified for inventory? The item is supplied as a single gauge pin; identification is via the article number M323.C05 and GTIN 4061905064791 for straightforward stock management. Is this pin appropriate for handheld in‑process checks? The compact length and balanced mass make the component practical for handheld checks where short, repeatable contact is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.07mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
A compact workshop gauge pin combining robust special-steel construction, a 12.07 mm diameter with ±0.002 mm tolerance and a 50 mm working length delivers reliable repeatable locating and end-measure checks; order directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin, single, 12.07 mm diameter — 50 mm length (Metav IndustryLine) A gauge pin (12.07 mm, 50 mm length) designed for precise locating and end-measure verification in workshop and fixture applications. Workshop-grade construction Diameter 12.07 mm for precision fits Tolerance ±0.002 mm for repeatability 50 mm special-steel body for durability Precise locating and repeatable measurements for production control The pin is engineered for repeatable positioning and end‑measurement tasks, with a diameter of 12.07 mm held to ±0.002 mm. This level of precision supports tight tolerances in jigs, fixtures and gauge sets and reduces rework by providing a stable datum for dimensional checks. The specified accuracy is consistent with workshop‑grade inspection tools and enables quick verification of bores and positional references without complex setup. Durable construction suited to frequent workshop use Constructed from special steel in a workshop version, the pin withstands routine handling and offers wear resistance for repeated insertion and withdrawal cycles. The 50 mm length provides sufficient engagement for many locating and end‑measure situations while remaining compact and easy to manipulate during assembly or checking tasks. Supplied as a single gauge pin, the item integrates readily into existing gauge sets and fixture arrays. Practical benefits for inspection and fixture building Using a dedicated gauge pin simplifies alignment of components and streamlines end‑of‑line checks; the precision diameter and low runout expectation support consistent results across repeated measurements. The product is designed for pragmatic workshop use rather than laboratory-only environments, combining precision, robustness and simple handling to improve throughput in production and maintenance operations. Contact Metav Werkzeuge for application guidance, compatibility checks and a bespoke delivery estimate for this 12.07 mm workshop gauge pin Technical data SKU: M323.C07 GTIN: 4061905065538 Material: Special steel Category: Gauge pin, single Facts Diameter: 12.07 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Single item supply Suitable for end‑measure and locating tasks Robust construction for frequent use FAQ What level of accuracy can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, making it suitable for precise locating and repeatable end‑measure checks in workshop environments. Which material is used for the pin and how does it affect durability? The pin is made from special steel, selected to provide wear resistance and longevity under frequent insertion and withdrawal typical for workshop use. Is this pin delivered as a single item or in sets? This product is supplied as a single gauge pin (SKU M323.C07), intended for integration into existing gauge sets or fixture arrangements. For which applications is the 50 mm length most suitable? A 50 mm working length gives adequate engagement for many locating and end‑measurement tasks while remaining easy to handle in assembly, inspection and fixture building. Can this pin be used for precision bore gauging and fixture alignment? Yes; the 12.07 mm diameter combined with ±0.002 mm tolerance makes the pin suitable for bore checking and accurate alignment duties in a workshop setting. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.08mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
A compact inspection solution that combines ±0.002 mm tolerance with a nominal diameter of 12.08 mm and a practical 50 mm length, enabling reliable pass/fail checks and repeatable gauging in workshop environments. Order this gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.C08 – single, Ø 12.08 mm, length 50 mm (Metav IndustryLine) Gauge pin M323.C08 is a single inspection pin designed for dimensional inspection and reference checks in metalworking and quality control contexts. Workshop version for robust daily use Nominal diameter 12.08 mm for precise fit control Length 50 mm for handheld and bench inspection Tolerance ±0.002 mm for high repeatability Reliable metrology for pass/fail and fit checks The inspection pin delivers consistent dimensional accuracy with a specified tolerance of ±0.002 mm, making it suitable for tight tolerance checks and plug-gauge comparisons. Its nominal diameter of 12.08 mm is produced to a controlled finish that reduces seating errors and wobble during insertion, which in turn improves repeatability when validating bores or mating parts. This level of precision supports efficient quality decisions and reduces the need for repeated rework or time-consuming measurements. Workshop-grade construction for everyday handling Manufactured in special steel, this inspection pin is engineered for the demands of a shop floor: wear resistance, stable geometry and straightforward handling. The 50 mm length offers a good balance between engagement depth and rigidity, while the workshop version construction resists nicks and deformation during routine use. The comparatively low mass and compact form factor make the pin easy to position in fixtures and jigs, and its finish minimises the risk of surface transfer or contamination during frequent checks. Seamless integration into inspection routines The pin is supplied with clear identification for traceability, enabling straightforward inventory and process control in production and inspection areas. As a single gauge element it pairs readily with comparator setups, ring gauges or simple go/no‑go fixtures, supporting fast decisions on conformity. The compact format also simplifies storage and handling in busy workstations; the component’s technical attributes make it a practical choice when reliable, repeatable gauging is required without complex accessories. For robust, repeatable inspection choose the Metav IndustryLine gauge pin M323.C08 and contact Metav Werkzeuge for tailored application guidance and procurement: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.C08 GTIN: 4061905065545 Category: Messstifte Dimensions & tolerances Diameter: 12.08 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Version: Workshop execution Accuracy class: ±0.002 FAQ What is this pin intended for? The gauge pin is intended for dimensional inspection and fit checks in quality control; the M323.C08 from Metav IndustryLine is suitable for verifying bore diameters and mating component fits. How precise is the gauge pin? This inspection pin is manufactured to a tolerance of ±0.002 mm, offering high repeatability for workshop‑level gauging tasks. Which material is used for the pin? The pin is made from special steel, selected for wear resistance and durability in routine inspection environments. Can the pin be used with go/no‑go fixtures? Yes. The nominal Ø12.08 mm diameter and controlled tolerance make the pin compatible with comparator setups and simple go/no‑go gauging arrangements. How is the item identified for inventory and traceability? The product is listed under SKU M323.C08 and GTIN 4061905065545 to support clear identification and traceability in procurement and quality systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.09 mm Gauge Pin, 50 mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.002 mm repeatability and a compact 50 mm length for reliable end-dimension checks; order directly via Metav Werkzeuge or consult our specialists for batch supply and technical advice. Gauge pin M323.C09 — Precision gauge pin, Ø 12.09 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.C09 is a single precision checking pin for end‑dimension verification and go/no‑go gauging in workshop inspection and production control environments. Workshop-grade precision design Diameter 12.09 mm tolerance ±0.002 50 mm hardened special-steel length Delivered in protective transport case High-accuracy checking for routine inspection The M323.C09 is engineered for consistent measurement accuracy in everyday workshop use. With an indicated accuracy of ±0.002 mm, this checking pin reduces measurement uncertainty during pass/fail checks and fits precision bores for end‑dimension verification. The compact 50 mm shank length and nominal 12.09 mm diameter allow quick insertion into gauges and fixtures, enabling faster throughput on inspection benches without sacrificing repeatability. This technical consistency supports tighter quality control and fewer downstream rejects. Built for the workshop: durability and handling Manufactured from special steel, the pin is finished to withstand regular handling and contact with measurement fixtures. The hardened surface provides resistance to wear, preserving the gauge diameter over many cycles and ensuring long service life in a production environment. Supplied individually and presented in a protective transport case, the component arrives ready for use and for safe storage between measurement tasks, reducing the risk of damage in transit or on the shop floor. Practical traceability and integration The compact design suits integration into existing inspection workflows, from handheld checks to fixture-mounted gauging stations. The single-item supply and clear labelling support traceability in small-batch production and calibration records. Its nominal dimension and tight tolerance make the pin suitable for precise end‑mass checks and use in selective fit testing, helping to maintain consistent assembly quality across repeated cycles. Contact Metav Werkzeuge for availability of the Metav IndustryLine gauge pin M323.C09 and for tailored supply or batch‑calibration guidance; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.C09 GTIN: 4061905065552 Manufacturer: Metav IndustryLine Label: Gauge pin, single, Ø 12.09 mm; Length 50 mm Facts Diameter: 12.09 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Supplied individually Delivered in plastic/wooden transport case Intended for end-dimension checking FAQ What is the specified tolerance for this gauge pin? The M323.C09 gauge pin is specified with an accuracy of ±0.002 mm, suitable for high‑precision workshop checks. Is the pin supplied as a single item or in sets? The product is supplied individually and delivered in a protective transport case for safe handling and storage. Which applications suit this gauge pin? This checking pin is intended for end‑dimension verification, go/no‑go gauging and precise fit checks in production and inspection workflows. What material is the pin made from and how does that affect wear? The pin is made from special steel with a hardened finish, offering good wear resistance for routine use in workshop environments. Where can the product identifiers be found for ordering and traceability? Use the article number M323.C09 and GTIN 4061905065552 when ordering or recording the item for traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.11mm Gauge Pin Length 50mm Workshop Finish, ±0.002 Accuracy - Metav IndustryLine
Reliable precision with robust workshop geometry: 12.11 mm diameter, 50 mm length and a guaranteed tolerance of ±0.002 mm make this single gauge pin ideal for repeatable end‑measurements. Order the gauge pin directly via Metav Werkzeuge or speak to our consultants for application guidance. Gauge pin M323.C11 – single precision gauge pin, 12.11 mm × 50 mm (Metav IndustryLine) The Gauge pin M323.C11 is a precision‑ground single gauge pin intended for end‑dimension checks and plug gauge assemblies in workshop and quality‑control environments. Diameter 12.11 mm precision ground Length 50 mm workshop version Tolerance ±0.002 mm ensured Special steel construction for durability Accuracy that secures repeatable end‑measurements High‑precision components demand stable reference pins; this gauge pin delivers by combining a 12.11 mm nominal diameter with a verified ±0.002 mm deviation. The tight tolerance is particularly beneficial where a measurable reference is required for go/no‑go checking, calibration jigs or end‑dimension verification of turned parts. The precision grinding process reduces surface irregularities and runout, which means fewer repeat measurements and a clearer pass/fail decision — an operational advantage for shops aiming to reduce inspection time without sacrificing reliability. Robust workshop design for everyday use Designed as a workshop version, the pin is machined from special steel to offer resilience against wear while retaining dimensional stability. The 50 mm length provides sufficient engagement for many plug and end‑measure scenarios while remaining easy to handle and position. At approximately 0.1 kg, the component is light enough for frequent use yet substantial enough to avoid flex under typical manual handling. The material choice and finish support repeated contact with mating parts, contributing to longer service intervals and predictable inspection outcomes. Integration into inspection processes and handling advice As a single measuring element, the pin suits insertion into fixture bores, feeler stacks and comparative checks; it can also be combined with other pins for stepped or nested gauges. Supplied individually, the unit fits compact inspection kits and can be stored alongside other reference standards. Routine practice such as gentle cleaning after use and protected storage will preserve the precision surface. For bespoke assemblies or batch requirements, the SKU M323.C11 and the Metav IndustryLine designation allow straightforward procurement and traceability within existing inspection workflows. For supply enquiries or technical advice on the Metav IndustryLine gauge pin M323.C11, contact Metav Werkzeuge in Emmerich – consultants are available to advise on suitability and dispatch arrangements Technical data Article number: M323.C11 GTIN: 4061905065576 Manufacturer: Metav IndustryLine Key measurements Diameter: 12.11 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Materials & features Material: Special steel Special feature: Workshop version Delivery form: Single gauge pin FAQ What is the stated tolerance of this gauge pin? The gauge pin M323.C11 is specified with a tolerance of ±0.002 mm, suitable for precise end‑measurement tasks in workshop environments. Which material is used for the pin and what does that mean for wear? The pin is made from special steel; this provides a durable surface that resists wear during repeated contact and maintains dimensional stability under normal workshop use. Can this pin be used in plug gauge arrangements? Yes, the single pin is intended for end‑dimension checks and can be integrated into plug gauge assemblies or fixtures where a 12.11 mm reference is required. Is the product supplied individually or in sets? This article is supplied as a single gauge pin under SKU M323.C11, allowing selective replacement or custom assembly of gauge nests. How should the pin be stored to preserve accuracy? After inspection use, clean the pin and keep it in a dry, protected compartment within the inspection kit to prevent corrosion and surface damage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.12mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, workshop‑grade durability and compact dimensions to streamline end‑dimension checks and fixture set‑ups; order the test pin directly via Metav Werkzeuge or consult their specialists for application advice. Test pin M323.C12 — 12.12 mm diameter · 50 mm length (Metav IndustryLine) The test pin M323.C12 is a workshop‑grade measurement pin designed for precise end‑dimension checks, gauge inserts and compact fixture applications in industrial and trade environments. Workshop‑grade construction Nominal diameter 12.12 mm 50 mm length for compact fixtures Tolerance ±0.002 mm high precision Precision that secures repeatable end‑dimension checks The test pin delivers a nominal diameter of 12.12 mm with a declared tolerance of ±0.002 mm, giving reliable repeatability for comparative checks and go/no‑go gauges. This level of accuracy supports consistent measurement outcomes in assembly and inspection routines, reducing the need for repeated adjustments. The narrow tolerance also simplifies statistical process control by lowering measurement scatter in small‑part verifications. Robust build tailored to workshop conditions Constructed from special steel and offered in a workshop‑execution, the pin resists ordinary shop wear while maintaining a true shaft profile for secure seating in fixtures. The compact 50 mm length combines rigidity with accessibility, allowing easy handling when installing into plates, pins or nested gauge blocks. The moderate mass supports stable placement without unnecessary inertia during manual operations. Designed for seamless integration with gauges and fixtures With its compact geometry and standardised dimensions, the pin is suited to retrofitting into existing inspection fixtures and bespoke gauges. The item’s M323.C12 identification and GTIN ensure traceable inventory handling and quick reordering. Where precision dowel alignment or end‑face reference is required, the pin provides a straightforward mechanical datum that reduces setup time and supports reproducible assembly references. For reliable end‑dimension controls and workshop‑ready durability, request the M323.C12 test pin from Metav Werkzeuge for tailored advice and fast procurement assistance. Technical details Article number: M323.C12 GTIN: 4061905065583 Material: Special steel Nominal diameter: 12.12 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special designation: Workshop execution Facts Category: Test pins Accuracy class: ±0.002 mm Intended use: End‑dimension checks, gauge inserts, fixture datum Special features Compact shaft for tight fixtures Robust surface finish suitable for repeated use Traceable identification (SKU and GTIN) Workshop‑grade mechanical stability FAQ What is the nominal diameter of this test pin? The test pin has a nominal diameter of 12.12 mm, providing a standard shaft size for tight‑tolerance datum applications. How precise is the pin for inspection use? The pin is specified with a tolerance of ±0.002 mm, which makes it suitable for high‑repeatability checks and fine gauge work in workshop environments. What material is used and is the design for workshop use? The component is manufactured from special steel and delivered in a workshop‑grade execution, optimised for routine handling and repeated insertion into fixtures. Which applications suit this test pin best? Typical uses include end‑dimension verification, insertion into go/no‑go and custom gauges, fixture datum points and alignment tasks where a compact, high‑precision pin is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.13mm Test Pin Length 50mm Workshop Version, Special Steel Case Included - Metav IndustryLine
Take advantage of the combination of high repeatability, workshop‑ready robustness and tight manufacturing tolerance for reliable end‑measure checks and fixture alignment; order directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin, single, 12.13 mm, 50 mm length — Metav IndustryLine workshop version Gauge pin, single, 12.13 mm is a precision inspection pin designed for end‑measure verification and fixture positioning in metalworking and quality‑control environments. Diameter 12.13 mm precision fit Length 50 mm workshop grade Tolerance ±0.002 mm accuracy Made from special steel for durability Consistent positioning for faster set‑ups A precisely matched cylindrical pin ensures repeatable locating and reduces alignment time. The 12.13 mm nominal diameter and a verified ±0.002 mm tolerance give a predictable interference or slip fit depending on the application, which translates to fewer trial adjustments during fixturing. In practical terms, two or three accurate locating points created with such a pin can shorten set‑up sequences and increase first‑pass yield; the result is a measurable improvement in throughput without requiring additional process steps. Robust construction for shopfloor demands The 50 mm length and special steel construction make this item suitable for daily workshop use where knocks and frequent handling occur. The workshop grade finish balances surface integrity with cost‑effective manufacturability, so the pin resists premature wear while remaining straightforward to replace when necessary. For users who require a compact, single‑piece solution for gauging or assembly jigs, this design delivers a durable locating element that keeps maintenance and inventory uncomplicated. Clear application scope and measurement benefits Use this inspection pin for end‑measure checks, fixture alignment, and transfer of reference dimensions in production and inspection routines. As a single, traceable component it integrates well into localisation tasks and manual quality checks, where geometric certainty of a reference point is required. Where tighter process control is sought, the tight ±0.002 mm specification supports statistical process control by reducing one source of measurement variation, helping to stabilise downstream machining and assembly operations. For workshop‑ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and procurement support via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.C13 SKU: M323.C13 GTIN: 4061905066191 Brand: Metav IndustryLine Facts Nominal diameter: 12.13 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Accuracy class: ±0.002 Special features Workshop version Material: special steel Single piece delivery Suitable for end‑measure and fixture alignment FAQ What nominal size does the pin provide? The pin is manufactured to a nominal 12.13 mm diameter and is suitable where that specific gauge is required for locating or measurement. How precise is the component for gauging tasks? The Metav IndustryLine gauge pin is produced to a ±0.002 mm tolerance, making it appropriate for precision inspection and reliable fixture positioning. Which applications are typical for this inspection pin? Typical uses include end‑measure checks, fixture alignment, transfer of reference points in machining centres and manual inspection benches. Is the item supplied as a single piece or in sets? This article is supplied as a single gauge pin and is identified by SKU M323.C13 for ordering and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.14mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise end‑dimension control with a robust gauge pin made from special steel, featuring an exact diameter of 12.14 mm and a length of 50 mm plus a tight tolerance of ±0.002 mm for repeatable inspection results; order directly via Metav Werkzeuge for reliable workshop supply and expert advice. Gauge pin, single, 12.14 mm — inspection pin, 50 mm length (Metav IndustryLine) A gauge pin, single, 12.14 mm designed for end‑dimension checks, alignment and reference measurements in workshop metrology. Workshop version, robust design Diameter precisely 12.14 mm Tolerance ±0.002 mm Delivered in protective box Accurate reference for end‑dimension checks As a compact inspection element, the gauge pin provides an uncompromising reference for short‑run checks and fixture alignment. The defined diameter of 12.14 mm and the declared tolerance of ±0.002 mm mean that the component is suitable where reproducible go/no‑go conditions or reference fits are required. The workshop‑grade construction keeps handling straightforward while the 50 mm length offers adequate engagement for many common bores and locating tasks, reducing set‑up time on the shop floor. Durable material and reliable handling Manufactured from special steel, the pin resists wear under normal inspection cycles and maintains dimensional stability during repeated use. The workshop version includes a protective case for transport and storage, which helps preserve the measuring surface and prolongs service life. Delivered clean and ready for use, this inspection pin simplifies routine quality checks and promotes repeatable measurement outcomes with minimal preparation. Practical fitment and process benefits Incorporating a hard, accurately turned reference pin into inspection sequences reduces measurement variation and shortens inspection loops. The compact geometry and robust finish make the item suitable for integration with gauges, fixtures and manual verification procedures commonly found in maintenance, toolrooms and small‑batch production. Backed by Metav’s focus on dependable supply, the component supports consistent process control without overcomplication. Contact Metav Werkzeuge today to secure workshop‑ready inspection pins and discuss fitment options—Metav Werkzeuge can advise on stock, delivery and compatible gauge systems at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.C14 GTIN: 4061905066207 Label: Gauge pin, single, 12.14 mm length 50 mm Facts Diameter: 12.14 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Supplied in protective box Category: Gauge pins (Messstifte) FAQ What are the exact dimensions of the pin? The gauge pin has a nominal diameter of 12.14 mm and a length of 50 mm; it is listed as M323.C14 from Metav IndustryLine. What tolerance and repeatability can be expected? The pin is specified with a tolerance of ±0.002 mm, providing tight repeatability suitable for workshop inspection and reference uses. Is the pin delivered protected for storage and transport? Yes, the item is supplied in a protective box to preserve the measuring surface during transport and storage. Which material is used for the inspection pin? The pin is made from special steel, chosen for dimensional stability and wear resistance in routine inspection tasks. What are the typical applications for this gauge pin? Typical uses include end‑dimension checks, locating and alignment in fixtures, reference checks in maintenance and small‑batch production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.15mm Gauge Pin Single 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade special steel, tight ±0.002 mm tolerance and compact dimensions to secure repeatable end‑dimension checks and reliable fixture alignment on small components. Order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Gauge Pin M323.C15 — 12.15 mm diameter, 50 mm length The Metav IndustryLine Gauge Pin M323.C15 is a single precision test pin designed for end‑dimension verification and alignment tasks in small‑component metrology. High-precision tolerance ±0.002 mm Special-steel, hardened construction 12.15 mm nominal diameter, 50 mm length Consistent, measurable precision for inspection workflows The compact test pin delivers a repeatable reference for go/no‑go checks and fixture set‑up, offering an industrial grade tolerance of ±0.002 mm. Such tight dimensional control reduces inspection scatter and shortens cycle time when measuring small bores or alignment features. The measured accuracy is stated as a clear numerical value, enabling straightforward integration into quality plans and statistical process control routines where traceable, reproducible measurements are required. Durable material and dimensional stability for workshop use Constructed from special steel, the pin provides a good balance of wear resistance and dimensional stability under normal workshop conditions. The 50 mm shank length and 12.15 mm nominal diameter suit a wide range of locating and checking tasks on small assemblies and precision parts. Robust material selection minimises fretting and profile change during repeated seating, which preserves tolerances over many cycles and supports longer service intervals before replacement is necessary. Practical application and system compatibility The single pin format is suitable for integration into inspection benches, gauge blocks, fixture tooling and manual plug checks. Its compact size makes it well adapted to precise end‑dimension checks and alignment in confined spaces typical of toolrooms and small‑batch production. Supplied as an individual reference pin, the component complements a set of standard gauges and assists in rapid verification without the need for complex fixtures, supporting efficient shop‑floor workflows and reliable pass/fail decisions. For assured measurement repeatability with the Metav IndustryLine gauge pin M323.C15 (±0.002 mm), contact Metav Werkzeuge in Emmerich for procurement and technical guidance. Technical data SKU: M323.C15 GTIN: 4061905066634 Item: Test pin, single, 12.15 mm nominal diameter, 50 mm length Manufacturer: Metav IndustryLine Facts Nominal diameter: 12.15 mm Length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.1 kg eClass: 21170231 Special features Workshop version Material: special steel Single precision gauge pin for end‑dimension checks FAQ What level of accuracy does this gauge pin offer? The gauge pin provides a dimensional tolerance of ±0.002 mm, specified for the Metav IndustryLine M323.C15 test pin. Which material is the pin made from and how does that affect wear? The pin is made from special steel; this construction balances hardness and stability to reduce wear and maintain dimensional integrity during repeated use. For which applications is the pin intended? The pin is intended for end‑dimension verification, fixture alignment and plug checks on small components; the Metav IndustryLine gauge pin M323.C15 is suited to inspection benches and manual verification tasks. Is this pin suitable for integration into fixture tooling? Yes, the single format and compact dimensions of the M323.C15 make it compatible with fixture tooling and gauge setups where a precise reference bore or shaft is required. What is the nominal size and length of the pin? The nominal diameter is 12.15 mm and the overall length is 50 mm for the Metav IndustryLine M323.C15. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.16mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact workshop gauge that combines repeatable dimensional control and robust material construction for dependable end‑dimension checks. The combination of 12.16 mm nominal diameter, 50 mm overall length and an accuracy of ±0.002 mm supports consistent in‑process verification; order directly via Metav Werkzeuge or consult our specialists for application advice. Inspection pin, single — 12.16 mm diameter, 50 mm length (Metav IndustryLine) A single inspection pin designed for end‑dimension verification and simple gauge applications in workshop metrology, offering precise contact and repeatable measurements. High precision ±0.002 mm tolerance Diameter 12.16 mm for end‑dimension checks 50 mm overall length, workshop specification Precise dimensional control for routine checks The inspection pin functions as a compact, high‑accuracy reference for end‑dimension measurements in production and assembly tasks. With a declared tolerance of ±0.002 mm, the pin is suitable for fine verification where small deviations matter; this precision reduces uncertainty during repetitive checks and supports quality control processes. The specification reflects industrial metrology practice and enables confident comparison against drawing tolerances or gauge limits. Robust construction for everyday workshop use Constructed from special steel, the gauge pin resists wear while maintaining contact integrity over repeated cycles, which preserves measurement reliability in busy workshop environments. The 50 mm overall length and 12.16 mm diameter provide a balance between handling convenience and sufficient engagement for end‑face inspection. The workshop designation indicates suitability for regular use without the need for bespoke mounting or fixtures. Integration into shop workflows and traceability As a single reference element, the pin simplifies quick go/no‑go checks and can be incorporated into existing fixture setups or bench gauges with minimal modification. Marking and the supplied article identifiers help maintain traceability in stock and inspection logs; the compact form factor also eases storage and rapid selection at the point of use. Where repeatability is essential, the gauge pin offers a straightforward, low‑complexity solution that supports consistent production quality. For reliable dimensional verification, request the Metav IndustryLine inspection pin from Metav Werkzeuge by phone or email for tailored technical advice and prompt supply Technical data Article number: M323.C16 GTIN: 4061905066641 Manufacturer: Metav IndustryLine Facts Nominal diameter: 12.16 mm Overall length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Material: Special steel Special features Workshop version Single inspection pin for end‑face checks Category: Gauge pin / Inspection pin ECLASS: 21170231 FAQ What is the intended use of this inspection pin? The inspection pin is intended for end‑dimension checks and simple gauge applications where a compact reference element with ±0.002 mm accuracy is required. Which materials is the pin manufactured from? The pin is made from special steel, selected to provide longevity and wear resistance in routine workshop use. Can the inspection pin be mounted in fixtures or bench gauges? Yes, the pin’s 12.16 mm diameter and 50 mm length suit integration into existing fixtures and bench‑style checking arrangements. How repeatable are measurements taken with this pin? Repeatability is supported by the declared tolerance of ±0.002 mm, which is suitable for precise routine verifications and narrow tolerance assessments. What identifiers accompany the product for traceability? The article is supplied with the SKU M323.C16 and GTIN 4061905066641 to assist stock control and inspection documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.17mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high dimensional accuracy ±0.002 mm, robust special steel construction and a compact 50 mm length for reliable end‑measure checks and fixture verification. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.C17 — precision ground plug gauge Ø 12.17 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.C17 is a precision ground plug gauge intended for end‑measurement, go/no‑go checks and alignment tasks in inspection and assembly environments. Precision tolerance ±0.002 mm Diameter Ø 12.17 mm 50 mm overall length Workshop‑grade special steel Reliable fit control for inspection and assembly A precision ground gauge pin such as this provides a consistent, verifiable datum for small‑bore checks and fixture set‑ups. The tight tolerance of ±0.002 mm reduces uncertainty when validating bores, locating holes or verifying mating parts, which in turn speeds up quality inspections and prevents costly rework. The compact form and 50 mm overall length make the pin easy to handle while still providing enough engagement for secure measurement contact; the result is repeatable verification without elaborate fixturing. Built for durability and repeatable results Constructed from special steel, the pin is hardened and finished to resist wear under repetitive use in workshop conditions. The hard, ground surface maintains diameter stability and surface quality so that measurement drift is minimised across many cycles. This durability supports predictable inspection intervals and contributes to a smoother production flow, since less frequent replacement or reshaping of gauges is required. Practical precision for everyday metrology tasks Engineered as a single‑piece plug gauge, the component is suited to end‑measure tests, alignment of assemblies and go/no‑go checks in quality control. The Ø 12.17 mm nominal diameter is manufactured to close tolerance and labelled accordingly for straightforward traceability. For shops standardising inspection procedures, this plug gauge serves as a compact, low‑complexity reference that complements calipers and micrometres and integrates easily into routine measuring stations. For precise fit validation and robust routine use, contact Metav Werkzeuge to request this Metav IndustryLine gauge pin or to discuss application suitability at your facility. Technical Data Article number: M323.C17 GTIN: 4061905066658 Manufacturer brand: Metav IndustryLine Category: Gauge pin / Plug gauge Facts Nominal diameter: 12.17 mm Length: 50 mm Mass: 0.1 kg Tolerance / accuracy: ±0.002 mm ECLASS: 21170231 Special features Material: special steel Single gauge, precision ground Workshop execution (robust design) Intended applications: end‑measure checks, alignment, go/no‑go testing FAQ What is the intended use of this gauge pin? The gauge pin M323.C17 from Metav IndustryLine is intended for end‑measurement checks, bore verification and fixture alignment in inspection and assembly tasks. How tight is the tolerance and what does it mean for inspection? The pin is manufactured to an accuracy of ±0.002 mm, which provides fine control for fit checks and reduces measurement uncertainty in routine quality inspections. Which material is the plug gauge made from and why does that matter? The M323.C17 is made from special steel, chosen for wear resistance and dimensional stability so the gauge maintains its diameter and surface quality over many cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.18mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
With a ±0.002 mm tolerance, Ø 12.18 mm diameter and 50 mm length, this single gauge pin provides workshop‑grade repeatability for end‑measure checks and fit verification; order the gauge pin directly via Metav Werkzeuge or consult our specialists for matching inspection sets. Gauge pin M323.C18 — single test pin, Ø 12.18 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.C18 is a compact, precision test pin designed for end‑measure and fit inspection in workshop and inspection environments. Precision tolerance ±0.002 mm Ø 12.18 mm — length 50 mm Workshop‑grade special steel construction Consistent precision for repeatable end‑measure checks The compact test pin delivers repeatable measurements thanks to its tight tolerance of ±0.002 mm, which places it in the high‑precision class for workshop gauges. Manufactured from special steel, the probe body retains form under handling and routine use, reducing measurement variation caused by wear. For practical inspection tasks such as checking hole diameters, plug fits or end‑masses, the hardened geometry and defined cylindrical form ensure that roundness and diameter remain reliable across multiple checks, supporting quality control workflows where reproducibility is essential. Designed for workshop handling and fast inspection routines As a workshop‑grade single pin with a 50 mm length and an intermediate diameter, this test pin balances reach with rigidity. The medium‑short shank keeps the probe stable during insertion and extraction, making it suitable for rapid sampling and repetitive checks on assemblies and components. The pin’s size and weight also simplify manual handling and storage in tool trays; when combined with a controlled inspection routine, the result is shorter cycle times and fewer measurement errors, which improves overall process efficiency on the shop floor. Fits micro‑range metrology and compatibility with inspection systems Classified within the micro measurement range (10–100 mm), this gauge pin is intended for fine mechanical work where compactness and accuracy are priorities. The single‑piece design serves as a reliable reference for go/no‑go tests, alignment checks and end‑measure verification. Where traceable comparison to master gauges is required, the pin can be integrated into inspection jigs or used alongside micrometres and bore gauges to cross‑check results. Its straightforward geometry also makes it a practical choice for custom fixtures and batch inspection setups. Contact Metav Werkzeuge for Metav IndustryLine gauge pins or request expert advice at info@metav-werkzeuge.com to configure inspection sets tailored to specific tolerance needs Technical data SKU: M323.C18 GTIN: 4061905066665 Diameter: 12.18 mm Length: 50 mm Material: Special steel Tolerance: ±0.002 mm Weight: 0.1 kg Facts Category: Gauge pins (Messstifte) eClass: 21170231 Label: Prüfstift, einzeln, 12,18 mm Länge 50 mm Special features Workshop version Single pin delivery Micro measurement range (10–100 mm) FAQ How precise is this gauge pin for routine inspection tasks? The gauge pin M323.C18 from Metav IndustryLine offers a precision of ±0.002 mm, making it suitable for high‑accuracy workshop checks and repeatable go/no‑go verifications. Is this pin suitable for measuring small bores and tight fits? Yes, the Ø 12.18 mm diameter and micro‑range classification make the pin appropriate for small bores, shaft fits and precision plug checks in fine mechanical and production environments. What material is the pin made from and how does that affect durability? Constructed from special steel, the pin provides enhanced wear resistance and dimensional stability, supporting long service life under normal workshop use. Can the single pin be used alongside other inspection tools in a quality workflow? The M323.C18 functions well as a reference element within jigs or as part of a cross‑check routine with micrometres and bore gauges; consult for set composition if multiple sizes are needed. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.19mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of tight tolerance, robust special‑steel construction and compact dimensions for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification support. Gauge pin M323.C19 — single inspection gauge pin, Ø 12.19 mm, length 50 mm (Metav IndustryLine) A M323.C19 single gauge pin engineered for precise end‑dimension verification and workshop inspection tasks. Workshop‑grade special steel construction Diameter 12.19 mm with ±0.002 mm tolerance Compact 50 mm length for confined checks Supplied in transport case for damage protection Precision where end‑dimensions matter The gauge pin delivers measurable confidence in rapid inspection routines. With a nominal diameter of 12.19 mm and a verified tolerance of ±0.002 mm, this inspection pin supports reproducible go/no‑go and feeler checks that cut rework and machine downtime. The controlled tolerance assists traceable quality assurance steps and makes the pin suitable as a reference for end‑dimension verification in incoming inspection and in‑process sampling. Robust workshop design for everyday inspection Manufactured in a workshop‑grade special steel, the inspection pin balances hardness and toughness for repeated seating and extraction. The 50 mm overall length and low mass (approx. 0.1 kg) make the pin easy to handle in confined jigs and assembly fixtures, while the supplied transport case reduces the risk of nicks that would affect measurement reliability. This practical design supports fast throughput in busy inspection benches without compromising tool life. Practical benefits and application scope Designed primarily for end‑dimension checks, the pin is ideal for quick verification of bore sizes, alignment checks and as a reference in fixture set‑up. The compact form factor suits workshop workflows where space and speed are priorities, and the tight tolerance enhances decision‑making in first‑article inspections. Traceable identification (GTIN and SKU available) simplifies inventory and document control, helping to integrate the pin into established quality processes. Contact Metav Werkzeuge to secure the Metav IndustryLine gauge pin Ø 12.19 mm (M323.C19) and to discuss its suitability for specific inspection or fixture applications Technical data SKU: M323.C19 GTIN: 4061905066672 Description: Single gauge pin, Ø 12.19 mm, length 50 mm Brand: Metav IndustryLine Facts Diameter: 12.19 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version (Werkstatt‑Ausführung) Supplied in transport case for protection Application: end‑dimension verification FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, providing the repeatability required for reliable go/no‑go and dimensional spot checks with the M323.C19 inspection pin. Which material is used for the pin? The pin is made from special steel in a workshop‑grade finish, chosen to resist wear while maintaining dimensional stability during routine use. Is the pin suitable for use in confined fixtures or jigs? Yes. The 50 mm length and compact diameter make it well suited for confined spaces, alignment checks and fixture set‑up in machine and assembly environments. How is the pin delivered and protected in transit? The pin is supplied in a transport case to protect the measuring surface from damage during storage and transport, preserving measurement integrity. For which inspection tasks is the pin most appropriate? Typical uses include bore verification, end‑dimension checks, alignment and fixture referencing where a precise, single‑diameter reference is required Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.1mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Compact gauge pin with workshop-grade durability: 12.1 mm nominal diameter and 50 mm length, offering repeatable checks with a tight tolerance of ±0.002 mm. Benefit from a small, robust inspection pin that speeds up end‑measure and go/no‑go routines; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 12.1 mm Ø × 50 mm (Metav IndustryLine) Gauge pin, single, 12.1 mm Ø and 50 mm length, designed for precise end‑measure and go/no‑go inspections in workshop and production settings High precision ±0.002 mm 12.1 mm nominal diameter 50 mm length for deeper checks Special steel construction Reliable accuracy for routine quality control The gauge pin delivers measurable benefits where reproducibility matters: a geometric reference with ±0.002 mm tolerance that reduces variability in pass/fail decisions and shortens inspection cycles. As a hardened inspection element with a defined nominal diameter of 12.1 mm, it is ideal for repeat checking of bore diameters, plug fits and end‑measure comparisons. The tight tolerance supports consistent results across multiple operators and fixtures, converting measurement certainty directly into lower rework rates and faster throughput. Robust, workshop‑grade design for everyday handling Constructed from special steel and finished for durable contact performance, this inspection pin is engineered for repeated use in workshop environments. The 50 mm active length gives enough reach for deeper sockets or assembly checks while remaining easy to handle; the listed mass of 0.1 kg balances stability and manoeuvrability. The M323.C10 designation aids traceability in stock and tooling lists, ensuring the part is quickly identified during process planning or exchange with metrology equipment. Practical integration into inspection workflows Use the pin as a reference probe for manual gauges, simple go/no‑go fixtures or as a tactile check during assembly inspection. Its straightforward geometry makes it compatible with common holding fixtures and gauge plates, supporting fast set‑up and minimal operator training. Clear identification via SKU and GTIN simplifies procurement and inventory management, and the workshop‑oriented specification makes it a dependable choice for maintenance, production sampling and calibration checks. For workshop‑grade precision and smooth procurement, contact Metav Werkzeuge to request availability or ask technical advisers about integration with existing gauges; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.C10 GTIN: 4061905065569 Category: Gauge pins Facts Diameter: 12.1 mm Length: 50 mm Accuracy/tolerance: ±0.002 mm Weight: 0.1 kg eClass: 21170231 Special features Material: special steel Workshop‑grade execution Single item delivery SKU: M323.C10 FAQ What tolerance can be expected from this inspection pin? The gauge pin is specified with a tolerance of ±0.002 mm, making it suitable for precise go/no‑go and end‑measure checks in workshop environments. Which material is used for the pin and why does it matter? Made from special steel, the pin offers wear resistance and stable contact properties, which preserves diameter integrity during repeated use. Is the pin suitable for deeper bore checks? Yes; the 50 mm length provides additional reach for deeper sockets and assemblies while remaining easy to handle for manual inspections. How is the item supplied — single or as a set? This is a single gauge pin supplied individually under SKU M323.C10. How can the pin be ordered or referenced in procurement? Refer to SKU M323.C10 or GTIN 4061905065569 when ordering to ensure the correct 12.1 mm × 50 mm gauge pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.2 mm Gauge Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop-grade gauge pin that pairs a 12.20 mm reference diameter with a 50 mm working length and a tight ±0.002 mm tolerance for reproducible setup and go/no-go checks — order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.C20 – 12.20 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.C20 designed for precise bore checking, fixture setting and end‑measurement tasks in a workshop environment Workshop version for robust daily use Diameter 12.20 mm for tight fit checks Length 50 mm for standard gauge setups Tolerance ±0.002 mm for high repeatability Reduce setup time with measurable repeatability The compact cylindrical design ensures a constant reference when aligning fixtures or checking bore sizes. With a 12.20 mm reference diameter and a stated ±0.002 mm variation, the pin delivers measurable repeatability that shortens setup and inspection cycles. The close tolerance reduces back‑and‑forth adjustments during assembly, translating into fewer stoppages on production lines and a clearer pass/fail decision in quality routines. Built to withstand workshop handling Manufactured from Special steel, the pin is configured for hands‑on use where robustness matters. The 50 mm working length is long enough for reliable engagement in common jigs while remaining easy to handle and store. The workshop version construction balances surface hardness and resistance to everyday knocks so that reference geometry remains stable over repeated use, lowering the need for premature replacements. Integrates into inspection and tooling workflows As a standard gauge‑style reference, this test pin fits into measuring benches, plug checkers and fixture arrays without requiring special adapters. The straightforward geometry simplifies documentation and traceability in inspection protocols and helps maintain consistent results across shifts. Combining durable materials with tight tolerance makes the pin suitable for routine quality control, sample testing and comparative checks in component production. For reliable, repeatable gauging in workshop environments contact Metav Werkzeuge for tailored supply and expert guidance from Emmerich Technical data Article number: M323.C20 GTIN: 4061905067495 Manufacturer: Metav IndustryLine Core measurements Diameter: 12.20 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Material & features Material: Special steel Workshop execution Category: Gauge pin / Messstifte FAQ What applications suit this gauge pin? The gauge pin M323.C20 is suitable for bore checking, fixture setting and end‑measurement tasks in workshop and production inspection environments. How precise is the reference diameter? The pin provides a reference diameter of 12.20 mm with a tolerance of ±0.002 mm, enabling tight fit checks and repeatable measurements. Is the pin suitable for everyday workshop use? Yes, the workshop execution and special steel construction make the pin durable enough for routine handling and integration into standard gauging setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.21mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme dimensional precision, robust special‑steel construction, and compact 50 mm length for reliable end‑measurement tasks in everyday workshop environments; order the component directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine Gauge Pin M323.C21 – 12.21 mm Ø, 50 mm length The gauge pin, single, 12.21 mm, length 50 mm is a hardened inspection pin designed for precise end‑measure checks, fixture alignment and reference gauging in metalworking and inspection stations. Workshop design for daily use Special steel construction Diameter 12.21 mm for end‑measure checks High repeatability ±0.002 mm Reduce rejects with measurable accuracy The compact inspection pin delivers a guaranteed accuracy of ±0.002 mm, making it suitable where consistent repeatability is essential for quality control. Manufactured from special steel, the pin resists wear and maintains its profile under frequent engagement, which reduces the need for repeated adjustments or replacements. For production lines that rely on small tolerances, this level of precision shortens inspection cycles and lowers rework rates, representing a clear efficiency gain for machining and assembly operations. Built for workshop routines and robust handling With a length of 50 mm and a precise diameter of 12.21 mm, this single gauge pin is optimised for routine use in jigs, fixtures and end‑of‑line inspection fixtures. The workshop execution means the geometry and surface finish are selected to withstand daily handling while preserving measurement integrity. As a straightforward hardened pin, it integrates with standard holders and clamping systems, so retrofitting into existing setups is uncomplicated and fast, supporting uninterrupted production workflows. Traceability, identification and practical benefits The item is supplied with clear identification (SKU M323.C21, GTIN 4061905067501) to simplify inventory and traceability. The modest weight of 0.1 kg and compact envelope allow storage close to the workstation and make handling effortless during rapid test cycles. Where process documentation is required, the stable material properties of special steel ensure that dimensional drift is minimised, supporting stable measurement data over time and improving confidence in inspection results. Contact Metav Werkzeuge for tailored advice on integrating the Metav IndustryLine gauge pin into inspection fixtures or for ordering information via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.C21 GTIN: 4061905067501 Brand: Metav IndustryLine SKU: M323.C21 Facts Diameter: 12.21 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Workshop execution Material: Special steel Single inspection pin Story trigger: endmasse FAQ Is this pin suitable for fixture alignment? Yes. The Metav IndustryLine gauge pin (M323.C21) is intended for fixture alignment and end‑measurement tasks where a 12.21 mm reference is required. What accuracy can be expected in routine use? Typical repeatability is reflected by the stated ±0.002 mm accuracy for the M323.C21 gauge pin when used in stable fixtures and handled according to good measurement practice. Which material is the pin made from and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability, which helps maintain measurement integrity over frequent use. Can the pin be used as a go/no‑go reference? Yes. As a precisely manufactured single gauge pin, it serves as a reliable reference for go/no‑go checks when combined with appropriate holders or limit gauges. How is the product identified for stock and traceability? The item is listed under SKU M323.C21 and GTIN 4061905067501, facilitating inventory control and traceability Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.22mm Gauge Pin Length 50mm Workshop Finish, Special Steel - Metav IndustryLine
Take advantage of workshop-grade robustness, special steel construction and a tolerance of ±0.002 mm for reliable small-part inspection; order the gauge pin directly via Metav Werkzeuge or consult our specialists if clarification is required. Metav IndustryLine gauge pin, single — 12.22 mm Ø, 50 mm length Gauge pin, single, 12.22 mm Ø, 50 mm length for precision end‑form checks and fixture set‑up in workshop metrology and quality control. Workshop-grade execution Diameter 12.22 mm, length 50 mm Special steel construction Tolerance ±0.002 mm Precision for small-part inspection Engineered for micro‑range measurement tasks, this gauge pin delivers a tolerance of ±0.002 mm, which places it in the realm of high‑precision workshop gauges. The nominal 12.22 mm diameter and 50 mm usable length allow stable engagement in bore and alignment checks while keeping thermal and handling influences low. For metrology routines that require repeatable end‑form verification, the tight tolerance reduces rework and shortens inspection cycles by providing a clear, objective reference dimension. Durable workshop design that endures daily use The special steel construction and workshop specification ensure mechanical resilience under routine handling and fixture contact. With a compact mass of 0.10 kg, the pin is easy to position while still offering sufficient mass to sit securely in place during manual or semi‑automatic checks. The robust finish resists galling and maintains the gauge surface geometry for long service intervals, supporting consistent measurement results and a lower total cost of ownership in production environments. Simple integration into inspection and setup processes Designed as an individual test element, the pin is ideal for plug‑gauge checks, go/no‑go fixtures and end‑dimension confirmations during set‑up or final inspection. Clear identification by SKU and GTIN facilitates traceability in inventory and quality records; this supports audit trails and process control in regulated production. The compact form factor and standard cylindrical geometry make the component straightforward to incorporate into existing gauge sets or bespoke jigs, improving throughput without extensive adaptation. For precise micro inspection tasks, contact Metav Werkzeuge to discuss the Metav IndustryLine gauge pin (SKU M323.C22) and arrange rapid supply from Emmerich; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.C22 GTIN: 4061905067518 Label: Gauge pin, single, 12.22 mm Ø, 50 mm length Facts Diameter: 12.22 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.10 kg Special features Material: Special steel Execution: Workshop version Application hint: End‑form inspection / fixture set‑up Story trigger: end masses FAQ What tolerance can be expected from this gauge pin? The gauge pin is specified with a tolerance of ±0.002 mm, providing high repeatability for micro‑range inspection tasks. Is this pin suitable for integration into fixture jigs? Yes. The single‑piece design and standard cylindrical geometry make the pin suitable for incorporation into go/no‑go fixtures and alignment jigs; the SKU M323.C22 identifies the exact item. Which materials is the pin made from? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability under typical workshop conditions. How is the item identified for inventory and traceability? Identification is possible via SKU M323.C22 and GTIN 4061905067518, which support ordering and quality‑record linkage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.23mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a combination of high precision, compact dimensions and robust workshop construction for consistent checking and alignment tasks; order the component directly via Metav Werkzeuge or request technical advice from our consultants. Gauge pin, single – Ø 12.23 mm, length 50 mm (Metav IndustryLine) A gauge pin for precise end‑measurement and fixture alignment in workshop and inspection environments, supplied as a single, workshop‑grade measuring pin Workshop-grade construction Diameter 12.23 mm, length 50 mm Tolerance ±0.002 mm for high precision Made from special steel for durability Precision engineering that reduces rework The pin is manufactured to a tight production tolerance of ±0.002 mm, which translates into reliable repeatability during routine checks and setup operations. Such precision ensures that positional checks, bore gauging and plug‑fit tests produce verifiable results rather than sporadic readings; the numerical tolerance gives a clear basis for acceptance criteria in quality control and reduces the need for corrective rework. The compact form factor keeps handling straightforward in busy workshop flows while maintaining measurement integrity. Robust material and workshop design for long service life Constructed from special steel and specified as a workshop‑grade item, the measuring pin resists wear and retains its nominal diameter over many insertion cycles. The 12.23 mm diameter together with a 50 mm overall length provides a balance between reach and rigidity, suitable for checking bores, alignment pins and reference points in jigs and fixtures. The material choice and finishing minimise surface damage and preserve concentricity, which supports repeatable fits and consistent part assembly. Practical traceability and simple integration into inspection routines Marked and stocked under SKU M323.C23, the component is ready for immediate incorporation into existing inspection sets or as a single‑item spare for fixture maintenance. The modest mass (0.1 kg) and single‑piece supply make logistical handling straightforward while the clear specification supports procedure documentation. Use in end‑measurement, go/no‑go checks or fixture referencing benefits from the pin's defined diameter and documented tolerance, enabling efficient decisions on assembly acceptance and process capability. Contact Metav Werkzeuge for procurement and expert guidance on how this workshop‑grade Metav IndustryLine gauge pin can be integrated into existing measurement routines Technical Data Article number: M323.C23 GTIN: 4061905067525 Brand: Metav IndustryLine Category: Gauge pins / Messstifte Facts Diameter: 12.23 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Material: Special steel Single pin supply SKU: M323.C23 FAQ What is the nominal diameter and length of this pin? The pin has a nominal diameter of 12.23 mm and an overall length of 50 mm. What tolerance can be expected from this Metav IndustryLine gauge pin? The component is produced to a tolerance of ±0.002 mm, suitable for precise checking and alignment tasks. For which applications is this measuring pin suitable? Typical uses include bore gauging, fixture alignment, end‑measurement and plug‑fit checks in workshop and inspection environments. Is the pin supplied as a single item or in sets? This product is supplied as a single gauge pin under SKU M323.C23. Can the pin be used for hardened or abrasive environments? The pin is made from special steel and designed for workshop use; for specific abrasive or extreme‑hardness applications, select materials and coatings should be considered. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.24mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of robust workshop construction, precise 12.24 mm nominal diameter and a tight tolerance of ±0.002 mm for reproducible end‑measure checks; order this gauge pin directly via Metav Werkzeuge or ask the consultants for application guidance. Gauge pin, single — 12.24 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single 12.24 mm — 50 mm length, engineered for precise end‑measure inspection and workshop applications Workshop-grade construction Nominal diameter 12.24 mm 50 mm overall length Tolerance ±0.002 mm Compact accuracy for fine inspection work A compact gauge pin with a nominal diameter of 12.24 mm delivers reliable repeatability for end‑measure checks and reference tests. The short, rigid geometry minimises elastic deformation during probing, which helps preserve measurement consistency in tight assemblies. Specified with a tolerance of ±0.002 mm, this pin supports fine evaluation tasks where small deviations matter; the result is reduced rework and more predictable quality control in routine inspection flows. Built for the workshop: durable material and handling benefits The workshop configuration combines a 50 mm length with special steel construction to withstand daily use on the shop floor. The chosen material provides wear resistance and dimensional stability, so the pin keeps its form under repetitive seating and withdrawal cycles. Lightweight handling characteristics improve ergonomics during fixture changes, while the robust design lowers the risk of deformation in common handling scenarios, ensuring longer service life and fewer replacement intervals. Integrates into established inspection processes Designed as a practical reference component, this gauge pin easily integrates into gauge fixtures, bores and comparative test setups. Its nominal diameter and defined tolerance support reproducible seating against datum surfaces, improving the traceability of measurement results across batches. For laboratories and workshop controls alike, the precise nominal value simplifies inventorying of reference parts and contributes to consistent pass/fail decisions during visual and dimensional inspections. For dependable end‑measure performance choose the Metav IndustryLine gauge pin and contact Metav Werkzeuge for tailored application advice and fast supply from Emmerich. Technical data Article number: M323.C24 GTIN: 4061905067532 Brand: Metav IndustryLine Category: Gauge pins Material: Special steel Facts Diameter: 12.24 mm Measuring range max: 12.24 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Workshop version End‑measure application Story trigger: end‑measure FAQ What is the nominal diameter of this gauge pin? The nominal diameter of the gauge pin is 12.24 mm; the product is listed as M323.C24 in the Metav IndustryLine range. What tolerance can be expected from the pin? The pin is specified with a tolerance of ±0.002 mm, suitable for tight end‑measure checks where high repeatability is required. How is this pin intended to be used in inspection? This gauge pin is designed for end‑measure inspection, integration into fixtures and for use as a reference pin in comparative checks and go/no‑go assemblies. Is the construction robust enough for regular workshop use? Yes — the workshop version is manufactured from special steel, providing wear resistance and durability for frequent handling on the shop floor. Can this pin be combined with standard test fixtures and gauge blocks? The gauge pin M323.C24 is suitable for use with common fixtures and reference setups, where a defined nominal diameter and tight tolerance improve measurement reproducibility. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.25mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop‑grade durability, pinpoint ±0.002 mm accuracy and compact dimensions for reliable end‑measure checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists in Emmerich for application advice. Gauge pin, single, 12.25 mm diameter, 50 mm length — Metav IndustryLine workshop version The gauge pin, single, 12.25 mm diameter, 50 mm length is a compact test pin designed for precision end‑measurement and bore checking tasks in workshop and inspection environments. Workshop version for industrial use Diameter 12.25 mm, length 50 mm High accuracy ±0.002 mm Supplied in transport case Precision tailored to compact inspection tasks The compact test pin is classified in the micro range (measurement range up to 100 mm), which makes it ideal for fine mechanical and small‑part inspection routines. The ±0.002 mm specification communicates the manufacturing tolerance and ensures tight repeatability when used as a reference or checking pin in gauge fixtures. For quality control, a defined tolerance reduces measurement variation and shortens decision times during go/no‑go assessments. Built for workshop handling and repeatable checks Constructed from special steel, the pin is presented in a workshop configuration that accepts frequent handling without sacrificing form stability. The short, stiff geometry and 50 mm overall length reduce flexing during insertion and extraction from bores, supporting consistent contact conditions. Supplied in a protective transport case, the item is protected during storage and transit, maintaining its surface condition for longer service life. Practical integration into inspection routines As a single gauge element, the pin suits quick interchange in fixture stacks, manual checking rigs and end‑measurement setups where compact, precise references are required. The 12.25 mm diameter is suitable for plug‑type verification and functional fit tests. Using a standardised, high‑accuracy pin simplifies logbooks and inspection records and harmonises measurement steps across several workstations, improving throughput and traceability. For reliable bore and end‑measure verification, specify the Metav IndustryLine gauge pin through Metav Werkzeuge or contact our Emmerich team for assistance with process integration Technical data Article number: M323.C25 GTIN: 4061905064104 Label: Gauge pin, single, 12.25 mm diameter, 50 mm length Manufacturer: Metav IndustryLine Facts Diameter: 12.25 mm Length: 50 mm Weight: 0.1 kg Accuracy / tolerance: ±0.002 mm Measurement range: 12.25 mm (fixed) Special features Workshop version Material: Special steel Supplied in transport case Category: Gauge pins ECLASS: 21170231 FAQ Is this pin suitable for precision bore checking? Yes. The gauge pin is specified for end‑measurement and bore checking; its ±0.002 mm tolerance supports precise go/no‑go assessments and repeatable inspection results. What material is the pin made from and why does it matter? The pin is made from special steel, chosen for dimensional stability and resistance to wear in workshop use; this maintains surface integrity and consistent fit during repeated checks. Can the pin be used in fixture stacks or manual gauges? Yes. The compact geometry and fixed 12.25 mm diameter allow the pin to be integrated into fixture stacks, manual checking rigs and inspection benches as a reference element. Is the product delivered ready for storage and transport? The item is supplied in a protective transport case, which preserves the pin's condition during transit and storage and reduces handling damage. Which SKU identifies this gauge pin? This gauge pin is listed as SKU M323.C25 and sold under the Metav IndustryLine label for workshop applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com