Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
2.54mm Gauge Pin, Single, ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
The combination of micrometre-level accuracy (±0.001 mm), robust special steel construction and compact 50 mm length ensures repeatable end‑measure checks in production. Order the pin directly via Metav Werkzeuge or consult the technical team for application advice. M323.254 Test pin — Gauge pin, 2.54 mm, ±0.001 mm (Metav IndustryLine) The M323.254 is a single gauge pin designed for precise end‑measure and assembly verification in workshop and inspection environments High precision ±0.001 mm Diameter 2.54 mm, length 50 mm Workshop‑grade special steel Single test pin for end‑measure checks Reliable micrometre‑level accuracy for production control Manufactured for tasks that demand minimal dimensional deviation, this gauge pin delivers ±0.001 mm accuracy, translating to consistent pass/fail decisions on tight fits and assembly tolerances. The defined diameter of 2.54 mm and compact 50 mm length make the pin suited to end‑measure checks, plug‑fit verification and small‑component gauging. Where reproducible measurement is essential, the narrow tolerance reduces rework and speeds up quality control cycles by providing an objective, verifiable reference. Durable workshop execution that withstands routine use The workshop‑grade construction and special steel composition combine wear resistance with dimensional stability so that the pin retains form under repeated handling. Surface condition and material choice minimise the risk of galling and preserve mating fits during inspection. For maintenance planning, the robust build reduces the need for frequent replacement, supporting predictable tool‑life and steady throughput in inspection benches and assembly stations. Practical fit‑check tool for inspection and assembly workflows Compact and straightforward to deploy, this single gauge pin integrates into go/no‑go checks, fixture validation and end‑of‑line sampling without complex setup. Traceability and clear specification allow integration into quality documentation and production records, while the small mass supports handheld use and rapid interchange in batch testing. The product’s precise specification assists calibration planning and simplifies comparison with CAD tolerances during design reviews. For secure supplies and expert guidance on integrating the Metav IndustryLine M323.254 into inspection routines, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss availability and technical matching. Technical data Article number: M323.254 GTIN: 4061905056260 Manufacturer: Metav IndustryLine Facts Diameter: 2.54 mm Length: 50 mm Accuracy/Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Version: Workshop execution Single test pin Category: Gauge pin (Messstifte) FAQ What tolerance can be expected from this gauge pin? The M323.254 test pin from Metav IndustryLine is specified at ±0.001 mm, providing micrometre‑level repeatability suitable for precise fit and end‑measure checks. Is this pin suitable for plug‑fit verification in assemblies? Yes; the 2.54 mm diameter and tight tolerance make the pin suitable for plug‑fit and end‑measure verification during assembly and inspection processes using the M323.254 gauge pin. What material is the pin made from and how does that affect wear? The pin is manufactured from special steel, chosen for durability and dimensional stability to minimise wear during repetitive inspection cycles. Can this pin be used for small‑component inspection in a workshop environment? Designed as a workshop‑grade test pin, the M323.254 is intended for routine inspection tasks, bench gauging and small‑component verification where compact, accurate references are required. How is the product identified for procurement and inventory? The product is listed as M323.254 with GTIN 4061905056260 to ensure clear identification in procurement and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.55mm Precision Probe ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Benefit from the combination of workshop‑grade construction, sub‑micron accuracy and compact dimensions for reliable end‑dimension checks. Take advantage of the precise diameter control and robust material to reduce scrap and inspection time. Order the inspection pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.255 — Inspection pin, Dia. 2.55 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.255 is a precision inspection pin designed for end‑dimension verification and go/no‑go checks in fine mechanical and workshop metrology. Workshop version for robust daily use Diameter 2.55 mm with ±0.001 mm tolerance 50 mm active length for deep checks Made from special steel for wear resistance Precision that minimises rework and inspection time The inspection pin delivers ±0.001 mm repeatability, a level of accuracy that supports tight end‑dimension control in serial checking and quality assurance. Manufactured to strict tolerances, the component reduces uncertainty in gauge stacks and plug tests, enabling faster go/no‑go decisions and fewer rejects. The combination of a precisely turned 2.55 mm diameter and a 50 mm length offers a reliable reference for small‑bore verification and end‑dimension measurement, translating directly into lower rework costs and improved process throughput. Tailored for micro‑range and fine mechanical tasks Classified for the micro range, this compact inspection pin suits tasks where minimal deflection and high positional accuracy are essential. Its dimensions make it particularly appropriate for small bores, connector pins and precision components found in watchmaking, instrumentation and miniature assemblies. The small footprint means handling is straightforward while maintaining stiffness at the contact point, so repeatable measurements are achievable even in confined setups. This focus on micro‑scale inspection supports consistent production quality where tolerances are measured in micrometres. Robust workshop design and material benefits The workshop version construction and special steel composition prioritise durability under frequent use. The material selection provides good wear resistance and dimensional stability, important for repeated insertion and extraction in production environments. A single‑piece design reduces potential error sources and eases traceability; the supplied unit is marked with the article identifier for inventory control. These factors combine to give a practical, long‑lasting inspection tool that integrates cleanly into existing bench equipment and inspection routines. For a precise match to production requirements and availability of Metav IndustryLine inspection tools, contact Metav Werkzeuge in Emmerich to discuss specifications and delivery options. Technical data Article number: M323.255 GTIN: 4061905056277 Category: Messstifte SKU: M323.255 Numbers / Core technical data Diameter: 2.55 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.005 kg Precision class: ±0.001 Special features Single inspection pin (einzeln) Workshop execution (Werkstatt‑Ausführung) Material: special steel Intended use: end‑dimension verification (endmasse) FAQ What applications is this inspection pin suited for? This inspection pin is ideal for end‑dimension checks, small‑bore verification and fine mechanical assemblies; the M323.255 from Metav IndustryLine is tailored to micro‑range inspection tasks. Is the tolerance of ±0.001 mm achievable in regular workshop conditions? Yes, when used with stable fixturing and consistent insertion force, the ±0.001 mm tolerance of the M323.255 can be realised, supporting reliable go/no‑go assessments and quality control. What material is used and how does it affect longevity? The inspection pin is made from special steel, chosen for wear resistance and dimensional stability under frequent use in workshop inspection routines. How is the pin identified for inventory and traceability? Each unit is supplied with the article identifier M323.255 and GTIN 4061905056277 to simplify stock management and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.56mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact, workshop‑grade test pin that combines ultra‑tight tolerance, robust special steel construction and a form factor made for repeatable end‑measure checks; order the item directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single, 2.56 mm, ±0.001 mm — 50 mm length (Metav IndustryLine) The Gauge pin, single, 2.56 mm, ±0.001 mm, length 50 mm is a workshop‑grade test pin for precise end‑measure inspections, plug and bore checking, and gauge setting in production and maintenance environments Workshop‑grade construction Diameter 2.56 mm ±0.001 mm 50 mm overall length for deep reaches Made from special steel Precision where small deviations matter Designed for applications that demand sub‑micrometre reliability, this compact test pin brings repeatable accuracy to routine checks. The diameter 2.56 mm combined with a tolerance of ±0.001 mm (one micrometre) ensures reliable fit‑up verification and end‑measure confirmation. In practice, that level of precision reduces setup time for inspection routines and lowers the risk of assembly rejects by providing a consistent physical reference for gauges and small bores. Robust build for workshop use and longevity Manufactured in special steel, the test pin resists wear and preserves the working diameter through repetitive use. The workshop‑grade execution prioritises handling and resilience over ultra‑fragile lab finishes, so the pin endures frequent insertion and removal in jigs, fixtures and inspection benches. The compact 50 mm shaft length balances reach and stiffness, keeping measurements steady without unnecessary flex. Efficient tool for quality control and gauge setting As a single gauge pin with a clearly defined nominal size and tolerance, this component streamlines go/no‑go workflows and manual gauge setting tasks. Where small bores or precise clearances are inspected, the pin serves as an objective reference that complements optical and dimensional checks. Its slim profile is ideal for confined geometries and end‑measure verification of small components, helping to accelerate routine checking and maintain consistent production quality. Contact Metav Werkzeuge for tailored advice and to reserve the workshop‑grade gauge pin M323.256 — call +49 2822 7131930 or eMail info@metav-werkzeuge.com to discuss compatibility and delivery options Technical data Article number: M323.256 GTIN: 4061905057144 Manufacturer: Metav IndustryLine Facts Nominal diameter: 2.56 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Workshop‑grade construction Material: special steel Intended use: end‑measure checks, plug and bore verification FAQ What is the nominal diameter and tolerance of this test pin? The gauge pin M323.256 has a nominal diameter of 2.56 mm with a tolerance of ±0.001 mm, making it suitable for high‑precision fit checks. Is this pin suitable for checking small bores and plug gauges? Yes. The M323.256 is designed as a single test pin for plug and bore verification and for setting mechanical gauges in workshop and production environments. What material is used for the pin? The M323.256 is manufactured from special steel, selected for wear resistance and dimensional stability under frequent use. How long is the pin and what reach does it provide? The overall length is 50 mm, which provides adequate reach for many confined geometries while maintaining stiffness for reproducible measurements. Can this component be used in assembly inspection to reduce rejects? Using the M323.256 as a defined physical reference for small clearances and end‑measure checks helps to standardise inspection results and can contribute to fewer assembly‑related rejects. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.57mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of absolute measurement precision, compact handling and workshop‑robust design for reliable end‑dimension checks; enquire with Metav Werkzeuge for matching sets or order the Test pin directly via Metav Werkzeuge. Test pin M323.257 — single gauge pin, 2.57 mm diameter, ±0.001 mm The Test pin M323.257 is a workshop‑grade gauge pin designed for high‑precision end‑measure verification and fixture alignment in fine mechanical applications. High‑precision Ø 2.57 mm ±0.001 mm Workshop‑grade special steel construction Compact 50 mm length for fixture and end‑measure Supplied in protective transport case Precision that secures process quality The production process benefits from a 2.57 mm diameter pin with an exceptional ±0.001 mm tolerance, delivering repeatable results when verifying final dimensions. Classified in the micro measurement range for compact instruments, this gauge pin is intended where minimal clearance and high reproducibility matter. Using a tight tolerance reduces rework and scrap rates, so inspection routines become a dependable part of the quality chain rather than a bottleneck. The compact geometry also minimises thermal and handling distortion during short‑cycle checks. Robust handling for busy workshops Built as a workshop‑grade component from special steel, the pin balances hardness with wear resistance to maintain dimensional integrity under routine use. With a length of 50 mm and a low mass (approx. 0.005 kg), the component is easy to position in jigs or fixture pockets while offering sufficient stiffness for manual placement. Supplied in a protective transport case, the pin arrives ready for immediate storage and safe transit between workstations, preserving the calibration state and surface finish important for accurate mating and alignment. Straightforward integration into inspection routines As a single, traceable gauge element, the pin is suited to end‑dimension checks, plug gauges and assembly alignment tasks where tight fits are required. Its compact size and workshop specification make it simple to include in existing gauge sets or to use as a reference for functional checks on small bores and pins. The straightforward design minimises ambiguity during inspection and speeds up operator training because the purpose and handling are immediately apparent. For series inspection, multiple identical pins can be ordered to establish fixtures with consistent reference points. For precise end‑measure verification or to configure a matched set from Metav IndustryLine, contact Metav Werkzeuge to secure the Test pin M323.257 or discuss technical matching options; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.257 GTIN: 4061905057366 Material: Special steel Length: 50 mm Diameter: 2.57 mm Accuracy: ±0.001 mm Weight: 0.005 kg Design: Workshop execution Facts Diameter: 2.57 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg GTIN: 4061905057366 Special features Workshop‑grade execution Supplied in protective transport case Single test pin for end‑measure verification Compact geometry for micro measurement range FAQ What material is the test pin made from? The Test pin M323.257 is manufactured from special steel designed for workshop use and wear resistance. Is the accuracy of ±0.001 mm suitable for fixture alignment? Yes, the ±0.001 mm tolerance of the Test pin M323.257 provides the precision required for demanding fixture alignment and end‑dimension checks. Does the pin come ready for transport or storage? The pin is supplied in a protective transport case to preserve surface integrity and dimensional accuracy during handling and transit. Can this pin be used for small bore checks and plug‑gage tasks? The compact 50 mm length and Ø 2.57 mm diameter make the Test pin M323.257 well suited to small bore checks, plug‑gage uses and mating‑part verification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.58mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of micron-level accuracy and robust workshop design for reliable end-dimension checks; the compact diameter and 50 mm length ensure secure seating and repeatable results. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. M323.258 gauge pin – 2.58 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The gauge pin (2.58 mm, ±0.001 mm) is a single precision test pin intended as a reference for dimensional inspection and end‑dimension verification in workshop and inspection environments. 2.58 mm diameter with ±0.001 mm tolerance Length 50 mm for stable engagement Manufactured from high-grade special steel Supplied in protective case for transport Micron-level accuracy for dependable inspection results This workshop‑grade test pin delivers a ±0.001 mm tolerance, making it suitable where micrometre‑scale reproducibility is required. The extremely fine tolerance is a rational choice for precision jigs, go/no‑go checks and calibration routines where small deviations translate directly into production quality. By using a dedicated reference pin with a defined diameter of 2.58 mm, inspection processes become measurable and comparable, which reduces uncertainty and supports faster go/no‑go decisions on the shop floor. Durable construction and handling designed for everyday use Constructed from special steel, the pin combines surface integrity with a compact form factor to resist wear during repeated seating and withdrawal. A length of 50 mm ensures stable engagement in bores and fixtures, simplifying alignment and reducing handling variability. Delivered in a protective case for transport, the item arrives ready for safe storage and mobility between workstations; this practical packaging protects the pin during transit and will help preserve its measurement integrity over time. Practical integration into inspection workflows The M323.258 pin is designed to be a straightforward metrology companion that fits existing gauges, fixture sets and inspection routines. Its compact mass (approximately 0.005 kg) minimises disturbance during delicate placements and supports repeatable results in serial checks. Using a dedicated gauge pin shortens measurement time and diminishes rework through more consistent acceptance criteria — a clear efficiency argument for production and quality teams that prioritise throughput without compromising on tolerances. For availability and personalised application advice on Metav IndustryLine precision pins, contact Metav Werkzeuge in Emmerich for technical support and stock information Technical data Article number: M323.258 GTIN: 4061905057373 Manufacturer: Metav IndustryLine Weight: 0.005 kg Facts Diameter: 2.58 mm Tolerance: ±0.001 mm Length: 50 mm Special features Material: Special steel Workshop version Supplied in a protective case for transport Category: Gauge pins (Messstifte) Story trigger: end-dimension checks FAQ What level of accuracy can be expected from this gauge pin? The M323.258 gauge pin is specified with a tolerance of ±0.001 mm, suitable for micron‑sensitive inspection tasks and precision checks. Can the pin be used in production fixtures and jigs? Yes, the pin’s 2.58 mm diameter and 50 mm length provide stable seating for fixtures and jigs used in workshop inspection and alignment operations. What material is the pin made from and how does that affect durability? The pin is made from special steel, chosen for its robustness in workshop use and resistance to wear during repeated engagement. Is the pin supplied with any protective packaging? The product is supplied in a protective case for transport, which helps maintain measurement integrity when moving between workstations. Which applications suit this gauge pin best? Typical uses include end‑dimension verification, bore checks and reference measurements where a precise, single‑diameter gauge pin is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.59mm Gauge Pin Single ±0.001mm Length 50mm Workshop Finish - Metav IndustryLine
Combine submicrometre accuracy with a robust workshop design to speed up inspections and reduce rework; rely on the 2.59 mm diameter and ±0.001 mm tolerance for repeatable end‑measurements and order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.259 — 2.59 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.259 is a single inspection pin designed for precise end‑dimension checks in workshop and metrology environments, ideal where tight fits and repeatable go/no‑go tests are required. Diameter 2.59 mm precision pin Tolerance ±0.001 mm for tight fits 50 mm overall length for depth checks Made from special steel, workshop grade Precision that minimises rejects A tolerance of ±0.001 mm (1 µm) positions this inspection pin in the high‑precision class for dimensional control. The very fine tolerance ensures reliable verification of bore and shaft fits during incoming inspection and final assembly, translating into fewer rejects and less rework. By using a dedicated precision pin rather than improvised probes, measurement uncertainty is reduced and decision limits become more consistent, which supports production efficiency and traceable quality control. Robust workshop construction for everyday use Engineered as a workshop execution, the pin is manufactured from special steel to withstand repeated use under industrial conditions. The 50 mm overall length provides sufficient reach for depth checks while remaining compact for easy handling and fixture use. The combination of stable material and compact geometry preserves roundness and dimensional stability over time, so maintenance intervals are extended and repeatability is maintained across inspection routines. Practical inspection workflow and compatibility Supplied as a single item, this gauge pin is aimed at bench inspection, fixture verification and go/no‑go testing of critical end measurements. The 2.59 mm diameter is suited to fine tolerances and small bores where accurate end measurements are decisive for assembly quality. Integrating the pin into existing inspection gauges or depth checks is straightforward and supports faster throughput by simplifying the verification step: a quick physical check replaces lengthy adjustment cycles and contributes to a smoother production flow. The compact weight also favours handheld checks and rapid fixture changes. Contact Metav Werkzeuge GmbH for specialist advice from Emmerich and to discuss how the M323.259 can be integrated into existing inspection routines Technical data Article number: M323.259 GTIN: 4061905057380 Material: Special steel Tolerance: ±0.001 mm Length: 50 mm Data Diameter: 2.59 mm Length: 50 mm Weight: 0.005 kg Tolerance: ±0.001 mm Special features Workshop execution Single item supply Category: Gauge pins (Messstifte) ECLASS: 21170231 Story trigger: end measurements FAQ What is the dimensional tolerance of this inspection pin? The M323.259 gauge pin is specified with a tolerance of ±0.001 mm, providing micron‑level control for precision fits. Is the pin suitable for depth and end‑face measurements? Yes — the 50 mm overall length makes this gauge pin suitable for depth checks and end‑measurement tasks in fixtures and bench inspections. What material is used for the pin and why does it matter? The pin is made from special steel, selected for dimensional stability and wear resistance so that measurement accuracy remains consistent under workshop conditions. How is the gauge pin supplied and intended to be used? The item is supplied individually as a single inspection pin, intended for direct use in go/no‑go checks, fixture verification or handheld dimensional checks. Which applications benefit most from this pin? Applications with tight bore tolerances, precision assemblies and end‑measurement controls benefit most; the pin supports repeated, repeatable checks that reduce rework. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.5mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial‑grade accuracy and robust workshop design for reliable end‑measurement in fixture and gauge production; the fine ±0.001 mm tolerance and slim 2.50 mm diameter ensure repeatable results and fast inspection cycles. Order the test pin directly via Metav Werkzeuge or contact their consultants for specification support. Test pin M323.250 — inspection pin, 2.50 mm diameter, ±0.001 mm (Metav IndustryLine) A single test pin, the M323.250, for precise end‑dimension checks and gauge fixtures in workshop metrology. Workshop design for rugged use Diameter 2.50 mm with ±0.001 mm tolerance 50 mm length suited to end‑dimension checks Made from special steel for long service life Consistent, measurable accuracy for routine inspection A compact inspection pin with a 2.50 mm diameter and ±0.001 mm tolerance delivers measurable improvements in process control. The narrow tolerance band permits reliable detection of micrometre‑level deviations during plug and gauge checks, which translates into fewer false rejects and more consistent lot acceptance. Where repeatability is critical, the controlled geometry and tight tolerance reduce uncertainty in comparative measurements and support efficient quality decisions. Built for workshop use and repeated handling The workshop design prioritises durability without compromising precision. Manufactured from special steel, the pin resists wear under frequent contact and maintains dimensional stability across repeated cycles. Supplied in a protective case for secure transport and storage, the test pin is ready for daily use at the inspection bench or as part of a gauge set. The robust finish and compact form factor keep maintenance intervals long and handling straightforward. Streamlined integration into inspection workflows This inspection pin suits end‑dimension verification and gauge fixtures where small‑diameter probes are required. The simple geometry makes the pin easy to seat in holders, mandrels or comparator fixtures, speeding up setup times and lowering per‑check overhead. Using standard identifiers such as SKU M323.250 and GTIN 4061905056222 helps with inventory control and traceability in production environments, supporting lean workflows and audit preparedness. Supports traceable quality processes and documentation Although supplied as a workshop tool, the component is designed to fit into documented quality systems. The material choice and tight tolerance facilitate reproducible measurements within established traceability chains; calibration to specific standards can be organised through usual metrology services if required. The combination of small form factor and high reproducibility makes the pin suitable for routines that demand both speed and documented measurement confidence. For precise end‑measurement components, request the Metav IndustryLine test pin M323.250 from Metav Werkzeuge — technical advice and order handling are available from Metav Werkzeuge at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: M323.250 GTIN: 4061905056222 Manufacturer: Metav IndustryLine Material: special steel Length: 50 mm Diameter: 2.50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Design: workshop version Delivery: supplied in protective case Numbers / Core technical data Diameter: 2.50 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Measuring range: 2.5 mm Special features / Versions Workshop construction for daily use Special steel for wear resistance Supplied in protective plastic or wooden case GTIN and SKU for traceability FAQ What applications is this test pin suitable for? The test pin M323.250 is intended for end‑dimension checks, plug‑gauge inserts and small‑bore inspections where a 2.50 mm reference probe with ±0.001 mm tolerance is required. Is the material corrosion‑resistant? The M323.250 is made from special steel selected for durability; surface condition and environmental exposure determine long‑term corrosion behaviour and should be considered when storing or using the pin. Can this pin be fitted into standard gauge holders? Yes, the simple cylindrical geometry of the inspection pin suits standard holders and mandrels used in gauge sets and comparator fixtures, facilitating quick integration into existing inspection rigs. Does the product come with a calibration certificate? The standard supply is the workshop version of the inspection pin; calibration to specific standards can be arranged through usual metrology services if a traceable certificate is required for the M323.250. How is the test pin supplied for transport and storage? The test pin is supplied in a protective case to safeguard the measuring surface during transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.61mm Test Pin Single ±0.001mm 50mm Workshop Finish - Metav IndustryLine
The combination of ±0.001 mm accuracy, a 2.61 mm diameter and a 50 mm length provides reliable end‑dimension control and reduced scrap in repetitive checks — order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.261 — single precision gauge pin, 2.61 mm, ±0.001 mm, 50 mm Gauge pin M323.261 is a single‑piece measuring pin designed for precise end‑measurement tasks in workshop environments and fixture set‑up Single gauge pin, 2.61 mm diameter Tolerance ±0.001 mm high precision 50 mm length for end measurement tasks Workshop version, robust workmanship Precision that reduces inspection uncertainty The M323.261 gauge pin delivers ±0.001 mm repeatability, making it suitable where tight dimensional control is required. Such fine tolerance significantly lowers the risk of false rejects and rework when used for end‑dimension checks or in assembly gauges. The close tolerance is achieved through controlled material selection and finish, which ensures consistent contact geometry; this reduces measurement scatter and supports reliable go/no‑go verifications and transfer measurements in serial inspection. Durable construction for daily workshop use Manufactured from special steel, the pin is engineered for repeated seating and withdrawal in hardened bushings and fixtures. The 50 mm shaft length combined with the 2.61 mm diameter offers a favourable stiffness-to-length ratio for end‑measure applications, improving handling stability compared with shorter or thinner pins. The workshop version designation reflects a focus on robustness and straightforward integration into everyday tooling — less downtime for replacement and consistent fit in gauges or locating plates. Practical application: where this pin adds value Used individually as a reference or locating element, the pin is ideal for end‑measure tasks, setting up jigs and verifying mating bores. Its single‑piece design simplifies stockkeeping and replacement in repair situations. Where equipment or fixtures require a precise datum pin for repetitive positioning, the combination of tight tolerance and durable material reduces variation between cycles and streamlines quality control routines. The pin supports efficient measurement workflows and contributes to reproducible assembly and testing processes. Contact Metav Werkzeuge for availability and tailored advice on integrating this precision gauge pin into existing fixtures or inspection routines Technical data Article number: M323.261 GTIN: 4061905057403 Manufacturer: Metav IndustryLine Facts Diameter: 2.61 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Delivery form: single piece Intended use: end‑measurement / locating tasks Version: workshop execution FAQ What is the intended application for this gauge pin? This gauge pin is intended for end‑measurement, locating and fixture work where a precise reference pin with ±0.001 mm tolerance is required. Is the material suitable for repeated seating in hardened bores? Yes, the pin is made of special steel designed for robust workshop use and repeated engagement in hardened bushings and locating holes. How does the 50 mm length affect handling and stiffness? A 50 mm shaft provides a good balance between reach and rigidity for end measurements; the 2.61 mm diameter helps keep deflection low for reliable positioning. Can this pin be used as a reference in assembly jigs? The single‑piece construction and tight tolerance make it suitable as a datum or locating element in assembly jigs and inspection fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.62mm Gauge Pin, ±0.001 mm Accuracy, Length 50 mm, Workshop Version - Metav IndustryLine
Precision measurement in a compact form: the combination of ±0.001 mm tolerance, a 2.62 mm diameter and a 50 mm length delivers reproducible end‑measure checks with minimal set‑up time; supplied in a protective transport case for safe handling. Order the pin gauge directly via Metav Werkzeuge or consult our experts for application advice. M323.262 Gauge pin – 2.62 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.262 gauge pin is a workshop‑grade inspection pin designed for precise end‑measure checks and fine positioning in toolmaking and quality control. ±0.001 mm tolerance for high precision Diameter 2.62 mm, length 50 mm Workshop‑grade special steel construction Supplied in protective transport case Accuracy that secures production tolerances High‑accuracy measurement reduces rejects and shortens inspection routines. With a declared tolerance of ±0.001 mm, this gauge pin offers micrometric repeatability that supports tight process windows and reliable end‑of‑line checks. The small nominal diameter of 2.62 mm places the component in the micro range, where compact dimensions and low deflection are essential; this makes the pin suitable for precision checks on small bores, jigs and delicate assemblies. The technical specification gives a clear, verifiable basis for pass/fail decisions and traceable production documentation. Built for workshop conditions and longevity A workshop‑grade design and special steel material provide a balance of wear resistance and dimensional stability under repeated use. The pin is supplied individually and protected in a transport case, which reduces the risk of handling damage and preserves the calibrated geometry during storage and transfer between measurement stations. The compact mass also makes the pin easy to position in fixtures and gauges, while the durable surface minimises maintenance intervals and supports consistent measurement results across production batches. Practical use and typical applications This gauge pin serves as an end‑measure reference for finishing, a setting aid for fixtures and a precise master for inspection benches—especially where small diameters must be verified. The compact form factor improves accessibility in confined setups and simplifies measurement sequences in toolmaking and small‑component assembly. Where traceable dimension checks are required, the pin integrates into existing inspection workflows and complements gauge blocks and plug‑gauge systems for quick comparative checks. Its single‑piece supply suits bespoke repairs, replacement tasks and occasional calibration routines without overstocking full sets. For workshop‑ready precision and fast availability from Emmerich, contact Metav Werkzeuge to discuss the M323.262 pin gauge and its use in production or inspection workflows; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.262 GTIN: 4061905057410 Brand: Metav IndustryLine Category: Gauge pins Core data Diameter: 2.62 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Workshop‑grade design Supplied in protective transport case Single‑piece supply Application: end‑measure checks and precision set‑ups FAQ What tolerance can be expected from this gauge pin? The M323.262 gauge pin is specified with a tolerance of ±0.001 mm, providing micrometric repeatability suitable for tight inspection criteria. Is the pin supplied individually or as part of a set? This item is supplied individually; the single‑piece supply supports targeted replacement and small‑batch testing without purchasing full sets. Which materials and applications are typical for this pin? Made from special steel, the pin is intended for workshop use in end‑measure checks, fixture set‑ups and small‑component inspection where compact reference diameters are required. How should the pin be stored to maintain accuracy? Storage in the provided protective transport case preserves the measuring face and reduces contamination, ensuring consistent measurement performance over time. Can the pin be used in confined or hard‑to‑reach fixtures? Yes, the compact 2.62 mm diameter and 50 mm length make the pin well suited to confined access situations and small‑bore measurements. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.63mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of extreme precision (±0.001 mm), a compact 2.63 mm diameter and a 50 mm length suited to deep seats; this workshop-grade gauge pin ensures reproducible end-measurements and secure fits. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin (single) M323.263 — 2.63 mm, ±0.001 mm tolerance The gauge pin for precise end-measurements and tight-fit checks in workshop and inspection environments, supplied as a single probe in a transport case. Tolerance ±0.001 mm for highest precision Nominal diameter 2.63 mm for tight fits Length 50 mm suitable for deep measurements Workshop version supplied in transport case Precision that keeps production within tolerance The M323.263 is manufactured to an exacting ±0.001 mm specification, which places it in the range of very high-precision plug gauges for small bores and end measurements. Such a tight tolerance reduces ambiguity during go/no-go checks and minimises the risk of defective assemblies. The small 2.63 mm nominal diameter is ideal where repeatability on micro-scale fits matters; the geometry and finish are optimised to reduce measurement scatter and to interact predictably with seating surfaces. Durable material and workshop-ready packaging Made from special steel, this single gauge pin is designed for routine use in production and workshop settings. The workshop version emphasises robustness while keeping handling straightforward: the 50 mm length provides reach into deeper features without sacrificing control. Delivery in a protective transport case preserves the reference surface during storage and transit, helping to maintain the pin’s metrological condition between inspection cycles and reducing unplanned downtime. Integrates into quality control workflows with ease As a compact reference probe, this item supports rapid inspection steps and clear go/no-go decisions, helping to speed up throughput while safeguarding quality. The small mass and simple geometry make the pin easy to position in inspection fixtures or manual test benches; traceable marking (SKU M323.263) eases inventory control and process documentation. Using a dedicated gauge pin for end-measurements contributes to a predictable measurement process and fewer returns due to assembly misfits. Choose the Metav IndustryLine gauge pin for reliable end-measurements—contact Metav Werkzeuge in Emmerich for tailored delivery and expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.263 GTIN: 4061905058226 Manufacturer: Metav IndustryLine Facts Nominal diameter: 2.63 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Supplied in transport case FAQ What is the intended use for this gauge pin? This gauge pin (M323.263) is intended for precise end-measurements, plug checks and tight-fit verification in workshop and inspection routines. Is the tolerance of ±0.001 mm sufficient for precision fitting? Yes — the ±0.001 mm tolerance places the pin among very high-precision gauges suitable for small-diameter fits and critical assembly checks. What material is the pin made from and how does that affect durability? The pin is made from special steel; this provides a wear-resistant surface and stability in typical workshop conditions. Does the product include protective packaging? Yes — the workshop version of the gauge pin is supplied in a transport case to protect the reference faces during storage and transit. How can the gauge pin be identified in stock or ordering systems? The gauge pin is listed under SKU M323.263 and GTIN 4061905058226 for inventory and ordering purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.64mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high measurement accuracy (±0.001 mm), a compact 2.64 mm diameter and a robust workshop design for reliable end‑measurement tasks; order the M323.264 directly via Metav Werkzeuge or consult our specialists for application advice. M323.264 gauge pin — precision test pin in workshop design, 2.64 mm diameter, ±0.001 mm tolerance M323.264 is a single precision gauge pin intended for end‑measurement and inspection tasks in production and workshop environments. Workshop version for robust handling Diameter 2.64 mm, high-precision fit Tolerance ±0.001 mm for end measurements Delivered in protective transport case Accuracy that secures final inspection results A tolerance of ±0.001 mm positions this gauge pin in the high‑precision class used for final checks and dimensional verification. The extremely fine tolerance ensures repeatable results when measuring critical end dimensions, so measurements become a reliable basis for pass/fail decisions in small‑part production. The compact 2.64 mm diameter and short 50 mm length minimise flex and contact variation, supporting consistent repeatability during routine use. Built for workshop use and straightforward handling The workshop version is manufactured from special steel, providing wear resistance and a tactile feel suited to frequent handling. At just 0.005 kg the pin is easy to manoeuvre while its solid construction maintains stability under normal contact forces. Delivery in a protective transport case keeps the pin secure between uses and during transport, reducing the risk of damage and preserving measurement integrity on the shop floor. Practical applications and production fit Designed for end‑measurements and small‑component inspection, this single test pin is suitable for slot, hole and bore verification where a tight gauge is required. The compact geometry and high accuracy make it a practical choice for quality control benches, toolrooms and precision assembly stations. The designation M323.264 and the clear specification simplify inventory management and traceability within production control systems, supporting documented inspection routines. Contact Metav Werkzeuge today for precise specification sheets or to request the M323.264 from Metav IndustryLine via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.264 GTIN: 4061905058233 Label: Prüfstift, einzeln, 2,64mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 2.64 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Delivered in a transport case Category: Messstifte Intended use: end measurements FAQ What are the exact diameter and length of the pin? The M323.264 gauge pin has a diameter of 2.64 mm and a length of 50 mm, as specified in the product label. What tolerance can be expected from this test pin? The test pin is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision end measurements. Which material is used for the pin? The pin is made from special steel, chosen for durability and stable dimensional behaviour in workshop conditions. Is the pin supplied ready for workshop use? Yes, the workshop execution and delivery in a protective transport case make the M323.264 ready for safe handling and storage in production environments. What typical tasks suit this gauge pin? The pin is ideal for end‑measurement tasks such as hole and bore checks, precision inspection of small components and final dimensional verification on assembly benches. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.65mm Test Pin, ±0.001 mm, Length 50 mm, Workshop Version, Special Steel - Metav IndustryLine
Benefitting from a ±0.001 mm tolerance and a Ø 2.65 mm precision ground diameter, this single gauge pin delivers reliable end‑measure checks in workshop environments; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.265 — single precision gauge pin, Ø 2.65 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.265 is a workshop‑grade single inspection pin designed for precise end‑measure and fit checks in small‑component assembly and inspection tasks. Tolerance ±0.001 mm for high accuracy Diameter 2.65 mm, precision ground Length 50 mm for end‑measure applications Workshop‑grade special steel construction Faster, measurable inspection with micrometric accuracy The gauge pin offers a repeatable ±0.001 mm tolerance that significantly reduces measurement uncertainty during quick pass/fail checks. Because the pin is precision ground to Ø 2.65 mm, it provides a defined reference diameter for end‑measure tasks and go/no‑go assessments. This level of consistency shortens inspection cycles and supports faster decision making on the shop floor, improving throughput without sacrificing traceability or measurement credibility. Built for daily workshop use and safe transport Designed as a workshop‑grade tool, the inspection pin combines a durable special steel construction with a compact 50 mm length that is easy to handle in confined assembly or inspection stations. The low mass contributes to swift handling, while the supplied transport case protects the measuring surface during storage and transfer. The rugged finish helps resist wear from repeated seating in bores and gauges, so the item remains reliable over many inspection cycles. Simple integration into inspection routines and tooling sets The single‑piece design makes the pin straightforward to incorporate into existing pin sets, plug gauges or fixture checks as a reference element for end‑measure verifications. Traceable identification via the SKU simplifies inventory control and replacement planning. For workshops seeking controlled, reproducible fits on small components, this inspection pin provides a compact, low‑maintenance means of verifying critical diameters and mating fits. Discuss specific measurement requirements with Metav Werkzeuge — our specialists in Emmerich advise on application suitability and delivery options for Metav IndustryLine products Technical data SKU: M323.265 GTIN: 4061905054860 Label: Prüfstift, einzeln, 2,65mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.65 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: special steel Workshop execution Delivered in transport case Category: Gauge pins (Messstifte) FAQ What level of accuracy does this gauge pin provide? The gauge pin M323.265 offers an accuracy of ±0.001 mm, making it suitable for fine end‑measure checks and tight tolerance verifications in workshop settings. Is the M323.265 suitable for repeated fit checks in production? Yes, the workshop‑grade construction and precision ground surface of the M323.265 are intended for repeated go/no‑go and end‑measure inspections as part of production workflows. What material is the inspection pin made from? This inspection pin is manufactured from special steel, chosen for wear resistance and dimensional stability under typical workshop conditions. Does the product come with a protective case? The M323.265 is supplied with a transport case to protect the measuring surface during storage and transfer. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.66mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, compact 2.66 mm diameter and rugged workshop design—ideal for repeatable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.266 — single inspection pin, 2.66 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The Gauge pin M323.266 is a single inspection pin designed for precise end‑measurement and fit checks in workshop and inspection environments Diameter 2.66 mm with ±0.001 mm tolerance Length 50 mm for end‑measurement checks Workshop design in special steel Supplied in a transport case for secure handling Precision that reduces rework and inspection time The small diameter and tight ±0.001 mm tolerance turn this inspection pin into a reliable reference for dimensional checks where minimal deviation is critical. High repeatability during pin gauging helps to reduce rework and scrap rates by providing a deterministic fit check; the 2.66 mm diameter is manufactured to narrow tolerances to ensure a consistent go/no‑go feel in fixtures and assemblies. In practice, using such a precise reference component shortens inspection cycles and supports faster decision making on the shop floor. Durable construction for everyday workshop use Built as a workshop version and made from special steel, the pin resists routine handling and contact wear while maintaining its measurement properties. The 50 mm length provides sufficient reach for most end‑measurement tasks without compromising stiffness; the small mass (approx. 0.005 kg) aids rapid manual handling and positioning. Supplied in a protective transport case, the pin arrives ready for safe storage and reduces the risk of damage during transit or on the bench—important where repeatability and surface condition affect measurement quality. Practical applications and integration into inspection routines This single inspection pin is suitable for end‑measurements, fit verification and component matching in toolmaking, small‑series assembly and quality control. As a compact, purpose‑built reference part it integrates straightforwardly into existing fixtures and gauges or can be used as a handheld check whenever a defined reference diameter is required. For customers seeking traceable procedures, the component supports standardised inspection routines and can be combined with working gauges to create robust, repeatable measurement steps. Contact Metav Werkzeuge for specific application recommendations on the Metav IndustryLine gauge pin M323.266 or to request a technical data sheet—phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: M323.266 GTIN: 4061905054877 Label: Gauge pin, single, 2.66 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 2.66 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Workshop version Material: special steel Supplied in transport case Single inspection/gauge pin Intended for end‑measurement checks FAQ What tolerance does the gauge pin provide? The gauge pin M323.266 is manufactured to a tolerance of ±0.001 mm, providing a high‑precision reference for tight fit and end‑measurement checks. Which material is used for this inspection pin? The inspection pin is made from special steel, chosen for wear resistance and durability in workshop environments. What applications suit this pin best? Typical uses include end‑measurements, fit verification and fixture checks in toolmaking, small‑series assembly and general quality control tasks where a precise reference diameter is required. How is the pin delivered and protected? The pin is supplied in a transport case to protect the measuring surface during storage and transportation and to ensure consistent condition at first use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.67mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
This high-precision gauge pin combines ±0.001 mm dimensional accuracy with a 2.67 mm nominal diameter and robust special-steel construction for consistent end‑mass control; supplied in a transport case for safe handling. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if further specification advice is required. Gauge pin M323.267 — 2.67 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.267 is a workshop-grade precision pin for end-mass checks and dimensional inspection in metrology and production control. 2.67 mm diameter, ±0.001 mm tolerance 50 mm length, workshop version Special-steel construction for wear resistance Delivered in transport case for safe handling Ensure repeatable, sub-micron-capable measurements High repeatability is at the core of this pin's design: the ±0.001 mm tolerance and fine-ground 2.67 mm shaft give a measurable improvement in positional certainty when used for end-mass checks or concentricity verification. In practical terms, the tight tolerance reduces rework and scrap by enabling earlier detection of out-of-tolerance conditions on assembly fixtures and test rigs. The result is a measurable increase in quality-control throughput and fewer downstream interruptions. Built for workshop handling and long service life The workshop-grade construction, realised in special steel, balances hardness with resistance to surface damage so that dimensional integrity persists under frequent use. At 50 mm overall length and approximately 0.005 kg weight, the pin is easy to manoeuvre for manual inspection while still offering a stable engagement in small bores. Supplied in a transport case, the pin remains protected during transit and storage, preserving the ground surface and ensuring consistent contact conditions at the measuring interface. Seamless fit into inspection routines and traceable stockkeeping Supplied under the designation M323.267 (GTIN 4061905054884), this pin integrates neatly into warehouse and inspection processes that rely on clear identification and reproducible artefacts. As a compact gauge pin, it supports quick pass/fail checks and can be used as a reference element in comparative measurement sequences. Backed by the Metav IndustryLine offering, the component benefits from established distribution and quality assurance channels, giving purchasing and QA teams the confidence of a consistent supply. Select the Metav IndustryLine gauge pin M323.267 for precise end‑mass verification and contact Metav Werkzeuge in Emmerich for procurement and specification guidance. Technical Data Article number: M323.267 GTIN: 4061905054884 Label: Gauge pin, single, 2.67 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.67 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Workshop version Material: Special steel Supplied in transport case Category: Gauge pin / measuring pin FAQ What is the permitted dimensional tolerance of this pin? The gauge pin M323.267 from Metav IndustryLine is manufactured to a tolerance of ±0.001 mm, suitable for high-precision end-mass checks. For which inspection tasks is the pin intended? The pin is intended for end-mass control, dimensional inspection and comparative checks in workshop and production metrology as a reference or go/no-go element. What material is used and how durable is it? Made from special steel, the pin offers enhanced wear resistance and maintains contact surface quality under routine workshop conditions. Can this pin be used for small-bore verification? Yes — the 2.67 mm diameter and fine ground finish make the pin appropriate for verification of small bores and locating features within its dimensional range. How is the product delivered and identified? The pin is supplied in a transport case and labelled with SKU M323.267 and GTIN 4061905054884 for clear identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.68mm Test Pin Length 50mm ±0.001mm Workshop Finish, Supplied in Case - Metav IndustryLine
Take advantage of the combination of workshop robustness, ultra‑fine ±0.001 mm tolerance and a compact 2.68 mm diameter in a 50 mm length to secure reliable end‑measure checks. Order the test pin directly via Metav Werkzeuge or consult the technical advisers for application‑specific guidance. Test pin M323.268 (Metav IndustryLine) — 2.68 mm, ±0.001 mm, 50 mm length A Test pin M323.268 designed as a high‑precision inspection pin for end‑measure reference and workshop gauging applications Ultra‑fine tolerance ±0.001 mm Diameter 2.68 mm for end‑measure checks 50 mm length in workshop execution Made from special steel for stability Consistent results through measurable precision The primary advantage of this inspection component is its ±0.001 mm tolerance, which places it in the high‑precision segment for plug and test pins. Such accuracy reduces ambiguity at the pass/fail boundary and improves repeatability in short‑run inspection tasks. The narrow 2.68 mm diameter, combined with a 50 mm length, makes the component especially suitable for end‑measure verification of small bores and stepped features. In practical terms, the tight specification shortens decision time during quality control and supports fine tolerancing in assembly processes. Material integrity and workshop suitability Constructed from special steel, the pin is engineered for dimensional stability and wear resistance in workshop environments. The material choice balances hardness with sufficient toughness to resist deformation under typical handling and insertion stresses. The workshop configuration indicates a robust finish and handling profile that resists nicks and accidental damage during frequent use. This makes the pin a dependable reference tool for bench inspection as well as for use in simple gauging fixtures where repeatable results matter. Integration into inspection routines and benefits Focusing on workflow, the component is configured as a single test pin that can be adopted directly into existing gauge sets or used as a standalone end‑measure reference. Its compact geometry supports access to confined features and stepped bores where larger gauges cannot reach. The design reduces set‑up time for small‑batch verification and simplifies traceable measurements in production. As a result, quality engineers and machinists gain a pragmatic balance of reach and rigidity for routine checks without the overhead of more complex gauging systems. Traceability, identification and practical notes The test pin carries a manufacturer SKU for clear identification and inventory control and is categorised under gauge pins for straightforward procurement. Where strict process documentation is required, the clear specification of 2.68 mm, 50 mm length and ±0.001 mm tolerance aids in traceable record‑keeping. For applications that demand particular surface conditions or additional finishing, consult the technical advisers to confirm suitability; the supplied data ensures compatibility with standard inspection procedures and end‑measure references. Contact Metav Werkzeuge today for tailored delivery of Metav IndustryLine test pins, specification advice and stock information via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data Article number: M323.268 GTIN: 4061905054891 Manufacturer: Metav IndustryLine Material: Special steel Diameter: 2.68 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Category: Messstifte (gauge pins) Facts Diameter: 2.68 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg GTIN: 4061905054891 Special features Workshop execution Single test pin Intended for end‑measure checks SKU: M323.268 FAQ What tolerance can be expected from this test pin? The test pin is specified with a tolerance of ±0.001 mm, ensuring high‑precision pass/fail decisions for end‑measure verification. Is the pin suitable for small bore inspection and stepped features? Yes, the 2.68 mm diameter and 50 mm length make the pin appropriate for confined bores and stepped measurements common in precision assembly. What material is used and how does it affect durability? The pin is manufactured from special steel, chosen for a balance of hardness and toughness to provide stability and wear resistance in workshop use. Can this pin be integrated into existing gauge sets? The single‑pin configuration is designed for direct incorporation into standard gauge assemblies or for standalone reference use in inspection routines. How is the product identified for ordering and inventory? The product is listed under SKU M323.268 and GTIN 4061905054891 for unambiguous procurement and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.69mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme dimensional accuracy, compact handling and workshop‑ready robustness to secure reproducible end measurements. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin M323.269 — single test pin, 2.69 mm, ±0.001 mm, 50 mm The Gauge pin M323.269 is a precision test pin for end‑measurement and alignment tasks in workshop metrology, suited to component verification and go/no‑go checks. Workshop version, robust design Diameter 2.69 mm with ±0.001 mm accuracy 50 mm length and low weight 0.005 kg High accuracy for reliable end measurements The gauge pin delivers substantial repeatability by offering a nominal diameter of 2.69 mm with a manufacturing tolerance of ±0.001 mm, making it suitable where tight dimensional control is required. The compact geometry and minimal mass contribute to reduced thermal and handling influences during short‑range checks, so measurements remain consistent. The component is crafted from special steel, providing wear resistance and surface integrity that support repeated insertion and withdrawal in inspection jigs and alignment fixtures. Practical workshop design that speeds up inspection Engineered as a workshop version, the pin combines robust construction with straightforward handling: a 50 mm shaft length and overall low weight (0.005 kg) allow easy positioning in small bores, fixtures or assembly gauges. The simple single‑piece design reduces sources of play and simplifies storage on inspection benches. Clear dimensional marking and compact form factor aid rapid identification and allow efficient use in production sampling routines, saving time while maintaining traceable measurement quality. Seamless fit into metrology and production workflows Traceability and repeatable results are supported by the unit’s clear identification: SKU M323.269 and GTIN 4061905054907 facilitate inventory and inspection documentation. The pin is particularly useful for end‑measurement, alignment and go/no‑go assessment in machining and quality control processes. Reliance on quantifiable characteristics such as diameter, tolerance and length enables objective pass/fail criteria and straightforward integration into existing inspection plans. Metav’s role as a precision partner further emphasises dependable supply and product support for industry and trade. Contact Metav Werkzeuge for application guidance on the Gauge Pin M323.269 — Metav Werkzeuge GmbH can advise on suitability for specific inspection setups; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for detailed information Technical data Article number: M323.269 GTIN: 4061905054907 SKU: M323.269 Facts Nominal diameter: 2.69 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.005 kg Special features Material: special steel Version: workshop execution Category: gauge pin / test pin Intended use: end measurement and alignment FAQ What accuracy can be expected from this test pin? The gauge pin M323.269 is manufactured to a tolerance of ±0.001 mm, suitable for tasks that require high repeatability in end measurements. Which material is used for the pin and why does it matter? The pin is made from special steel; this material selection ensures surface durability and resistance to wear during repeated use in inspection fixtures. Is the M323.269 suitable for go/no‑go checks on small bores? Yes, the 2.69 mm diameter and rigid single‑piece design make the M323.269 appropriate for go/no‑go assessment and alignment in small bore applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.6mm Test Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micron accuracy (±0.001 mm), a compact Ø 2.60 mm profile and a practical 50 mm length for dependable end‑measurement checks in routine production. Order the item directly via Metav Werkzeuge or consult Metav's specialists for application advice. M323.260 Gauge pin — Ø 2.60 mm, ±0.001 mm (Metav IndustryLine) The M323.260 gauge pin is a workshop‑grade inspection pin designed for precise plug and bore checks and end‑measurement tasks in production and inspection environments. Workshop version for routine inspection Diameter 2.60 mm, tolerance ±0.001 mm 50 mm special steel pin for easy handling Supplied in a protective transport case Suitable for end‑measurement and go/no‑go checks Precision that secures production quality The core advantage of this inspection pin is its ±0.001 mm tolerance — equivalent to 1 µm — which provides a level of dimensional certainty that reduces rejects and accelerates quality decisions on the shop floor. Used as a reference for end‑measurements and final size checks, the compact Ø 2.60 mm diameter and consistent geometry improve the repeatability of go/no‑go inspections and comparative gauging. Such micron‑level accuracy is particularly valuable where small clearances and tight fits determine assembly performance or where final dimensions are critical to downstream processes. Built for everyday workshop use Manufactured in special steel, the pin balances wear resistance with manageable handling in daily operations. The 50 mm length offers enough engagement for reliable contact while remaining compact for use in confined setups and fixtures. As a workshop‑grade article, the design supports frequent handling and straightforward integration into inspection rigs or gauges without introducing unnecessary bulk. Delivery includes a protective transport case, ensuring safe transit between stores, machines and measuring benches and preserving the pin's geometry during routine movement. Practical application and operational benefits This inspection pin suits a wide range of tasks — from precise end‑measurements and bore verification to use as a reference gauge in assembly verifications. The single‑piece supply simplifies traceability and storage: each pin can be recorded by its SKU and GTIN and kept ready for immediate use in measurement sequences. Because the design focuses on consistent contact geometry, cycle times for checks can be shortened and measurement uncertainty reduced, supporting leaner control loops and steadier production throughput. For supplementary technical details or application recommendations, Metav's measurement specialists are available to advise on best practices and integration. Order the M323.260 from Metav Werkzeuge for reliable micron‑level checks or contact Metav Werkzeuge's consultants at info@metav-werkzeuge.com / +49 2822 7131930 for tailored application advice Technical data Article number: M323.260 GTIN: 4061905057397 ECLASS: 21170231 Label: Prüfstift, einzeln, 2,60mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.60 mm Tolerance: ±0.001 mm (1 µm) Length: 50 mm Weight: 0.005 kg Special features Workshop version (Werkstatt‑Ausführung) Material: special steel Supplied individually Delivered in a protective transport case Intended for end measurements / final size checks FAQ What is the dimensional tolerance of the pin? The M323.260 gauge pin is specified at ±0.001 mm, which corresponds to 1 µm, ensuring very fine dimensional control for inspection tasks. What material is the gauge pin made from? The pin is manufactured from special steel, chosen for durability in workshop and production use. For which inspection tasks is this pin suitable? The inspection pin is suitable for end measurements, plug and bore verification, go/no‑go checks and use as a reference in small‑part assembly and quality control. How is the item delivered and identified? The pin is supplied individually and shipped in a protective transport case. Identification is by SKU M323.260 and GTIN 4061905057397. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.71mm Gauge Pin Single, ±0.001 mm, Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm tolerance, a compact Ø 2.71 mm diameter and a resilient special steel finish for reproducible end‑measure checks. Order directly via Metav Werkzeuge or contact the consultants for application advice. Test pin M323.271 — single test pin, Ø 2.71 mm, ±0.001 mm, 50 mm (Metav IndustryLine) A Test pin M323.271 designed for precise end‑measure verification and fixture referencing in workshop metrology environments. ±0.001 mm tolerance Ø 2.71 mm diameter Length 50 mm for end‑measure checks Consistent precision that speeds inspection Engineered for repeatable reference measurements, this gauging pin delivers a tolerance of ±0.001 mm, which substantially reduces measurement uncertainty during routine checks. The fine tolerance makes the pin suitable for tasks that demand minimal deviation, such as end‑face gauging, alignment of fixtures and verification of bore fits. Using a reference pin with defined geometry reduces rework and accelerates quality control cycles, providing a clear productivity advantage on the shop floor. Robust construction for workshop conditions Manufactured from special steel, the component balances hardness and wear resistance while retaining the dimensional stability needed for repeated contact with mating parts. The workshop execution ensures the pin is suitable for everyday use in industrial environments where handling and surface contacts are frequent. A length of 50 mm provides sufficient reach for many fixturing situations, while the compact diameter keeps the pin easy to guide and position in narrow bores or alignment jigs. Practical benefits for inspection and assembly As a single‑piece test pin, the component integrates into existing gauging sets and can be used as a master reference in go/no‑go setups or as a datum for assembly fixtures. The small mass and rigid geometry ensure low thermal drift during short inspection cycles, supporting faster measurement routines. Clear, verifiable specifications simplify documentation and traceability in quality processes, helping to maintain consistent product tolerances across batches. For reliable end‑measure checks, choose the Metav IndustryLine test pin and contact Metav Werkzeuge for procurement and technical guidance. Technical data Article number: M323.271 GTIN: 4061905054921 Manufacturer: Metav IndustryLine Dimensions and accuracy Diameter: 2.71 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Materials and special features Material: special steel Version: workshop execution Delivery: single test pin FAQ What tolerance can be expected from this test pin? The test pin M323.271 has a specified tolerance of ±0.001 mm, making it suitable for high‑precision reference and inspection tasks in workshop metrology. Is the material suitable for frequent contact with hardened mating parts? The pin is made from special steel designed for wear resistance; for contact with heavily hardened components, inspection intervals should be matched to the application to monitor wear. Can this pin be used as a master for go/no‑go gauging? Yes, the single test pin functions as a master reference for go/no‑go arrangements and datum setting within assembly and inspection fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.72mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Benefit from workshop‑grade robustness combined with sub‑micron accuracy: the pin's ±0.001 mm tolerance and precision ground finish ensure reliable end‑measure checks and repeatable fits. Order the item directly via Metav Werkzeuge or consult the technical team for application advice. M323.272 gauge pin — workshop test pin, 2.72 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.272 is a workshop‑grade gauge pin designed for precise end‑measure and fit checks in inspection, fixture set‑up and pin‑block assemblies. Sub‑micron tolerance ±0.001 mm Diameter 2.72 mm, precision ground Length 50 mm, workshop‑grade design Delivered in transport box for protection Consistent sub‑micron accuracy for inspection tasks The M323.272 functions as a dedicated gauge pin for end‑measure verification and gauge assembly work. Its ±0.001 mm tolerance combined with a precision ground surface minimises measurement uncertainty and ensures stable contact conditions during go/no‑go checks or plug‑gauge comparisons. In practical terms, the tight tolerance reduces make‑or‑break decisions at assembly and inspection points, shortening rework loops and supporting tighter process control. Robust workshop construction for reliable handling Constructed from special steel, the pin offers a balance of wear resistance and dimensional stability suited to everyday workshop use. The 50 mm length and compact 2.72 mm diameter make the pin easy to seat in fixtures and pin blocks while retaining sufficient overhang for handling. The workshop‑grade finish tolerates normal handling and protects functional surfaces; delivery in a transport box keeps the part protected between uses and during transport, preserving the measuring edge and extending service life. Designed for repeatable workflows and fast inspection Integration into inspection benches, pin holders or comparison setups is straightforward thanks to the standardised size and the pin's repeatability. The robust geometry supports fast exchange in testing sequences and reduces setup time in small‑batch or series production. The product is traceable via GTIN 4061905055379, supporting inventory management and procurement processes; Metav IndustryLine’s quality filter further ensures consistent supply and suitability for industrial inspection applications. For precision end‑measure checks, request the M323.272 from Metav Werkzeuge — Metav’s Emmerich team can advise on fitment, set composition and supply at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.272 GTIN: 4061905055379 Manufacturer: Metav IndustryLine Core specifications Diameter: 2.72 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Materials & features Material: Special steel Workshop‑grade design Precision ground surface Supplied in transport box FAQ What is the diameter and tolerance of this gauge pin? The gauge pin has a diameter of 2.72 mm with a tolerance of ±0.001 mm, suitable for tight fit‑checking and precise inspection tasks. Can the pin be used in pin blocks and fixture plates? Yes, the pin’s standard geometry and 50 mm length make it compatible with common pin‑block systems and fixture set‑ups. Is the material specified for the pin suitable for workshop use? The pin is made from special steel, selected for wear resistance and stability under typical workshop conditions. Is there a calibration certificate included with the item? No specific calibration certificate is stated in the product data; any calibration requirements should be clarified with Metav Werkzeuge prior to purchase. How is the pin delivered to protect the measuring surface? The part is supplied secured in a transport box to protect the precision surface during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.73mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of a compact, highly‑accurate gauge pin that combines ±0.001 mm tolerance with a 2.73 mm diameter and a robust 50 mm length for reliable end‑measure verifications; supplied in a protective transport case, the workshop‑grade design supports repeatable inspections and easy handling — order via Metav Werkzeuge or request advice from our consultants. M323.273 Gauge Pin — 2.73 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The M323.273 gauge pin is a workshop‑grade precision pin designed for end‑measure checks, go/no‑go verifications and fixture set‑up tasks in inspection and toolmaking environments Workshop-grade construction Diameter 2.73 mm, tolerance ±0.001 mm Length 50 mm for repeatable end measurements Supplied in protective transport case Accuracy that shortens inspection cycles A ±0.001 mm tolerance places this gauge pin in the high‑precision segment for workshop inspection tools. The exceptionally tight tolerance reduces measurement uncertainty and speeds decision making during incoming inspection or in‑process checks. Because the pin is manufactured from special steel, dimensional stability and wear resistance are improved, which sustains repeatability over many cycles and reduces the need for frequent replacement. This combination of tight tolerance and durable material supports faster throughput in quality control workflows. Robust handling and protected transport for daily use With a 50 mm active length and workshop‑grade finishing, the pin balances reach and rigidity for routine end‑measure tasks. The shorter overall form factor makes it easy to position in fixtures and jigs while remaining resistant to bending under normal handling. Delivery includes a protective transport case, intended to prevent transit damage and maintain the pin’s calibrated condition during storage and movement — the case is optimised for transport rather than permanent storage. These practical design choices reduce handling errors and protect the critical gauge surface. Simple integration into measurement routines The gauge pin is suitable for plug‑gauge style checks, verification of end‑masses and dimensional references in assembly fixtures. Its 2.73 mm nominal diameter matches common small‑bore inspection needs, enabling consistent reference points across inspection plans. The high precision and stable material allow the pin to serve as a transfer standard between manual gauges and CMM fixturing, improving traceability and helping to maintain process capability indices in serial production. Fewer rejections and clearer tolerance decisions are the direct benefits. Ready for workshop procurement and stock management As a compact, high‑accuracy test pin, the item is straightforward to specify and stock. The M323.273 designation and compact packaging make it easy to identify in stores and on inventory lists, while the special steel construction supports long service life under typical workshop conditions. For purchasing and planning, inclusion in routine inspection kits or as a replacement reference in jigs reduces downtime and keeps measurement baselines consistent across shifts. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge for technical advice or to secure the M323.273 gauge pin for immediate dispatch — Metav Werkzeuge provides detailed product guidance and reliable logistics from Emmerich. Technical data Article number: M323.273 GTIN: 4061905055386 Manufacturer: Metav IndustryLine Dimensions & tolerances Diameter: 2.73 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Features & materials Workshop version Material: special steel Supplied in transport case Category: gauge pin (Messstifte) FAQ What is the intended use of this gauge pin? The gauge pin is intended for end‑measure verifications, plug‑gauge checks and fixture set‑up tasks; the M323.273 provides a stable reference diameter of 2.73 mm with ±0.001 mm tolerance for these operations. How durable is the M323.273 under regular workshop use? Made from special steel and delivered in a protective transport case, the M323.273 is designed for durable routine use and maintains dimensional stability across repetitive checks. Is the transport case suitable for long‑term storage? The supplied case is intended for safe transport and short‑term storage to protect the measuring surface; it is optimised for transit rather than permanent long‑term storage of precision gauges. Can this pin be used as a reference in fixture calibration? Yes — its tight tolerance and stable material make the M323.273 suitable as a transfer standard between manual gauges and fixture set‑ups in quality control processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.74mm Test Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra-fine ±0.001 mm tolerance, a compact 2.74 mm diameter and a stable 50 mm reference length to reduce inspection uncertainty and rework in serial production; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application support. M323.274 gauge pin — single precision plug, 2.74 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.274 gauge pin is a single precision measuring plug designed for end-dimension verification and hole inspection in workshop and inspection environments. High precision ±0.001 mm tolerance Diameter 2.74 mm for precise fits 50 mm length for reliable reference Workshop version in special steel Precision that cuts rework and inspection time This measuring plug delivers industrial-grade accuracy with a tolerance of ±0.001 mm, making it suitable for high-precision fit checks and final inspection of critical end dimensions. Such a fine tolerance reduces the need for repeat measurements and downstream rework, which translates directly into improved throughput and lower scrap rates. The small 2.74 mm diameter is ideal for tight holes and dowel seats where micron-level clearance matters; by explaining the practical effect of the tolerance, non-specialists can understand that less variation at the gauge stage means more consistent assembly quality on the line. Robust form for repeatable handling in the workshop Manufactured from special steel and specified as a workshop version, the pin balances wear resistance with tactile stability during manual gauging. The 50 mm length offers a reliable reference for both end-face and through-hole checks, helping technicians maintain consistent measurement posture and contact. A compact, single-pin format simplifies storage and transport within inspection kits, while the nominal weight supports steady seating in fixtures. The construction focuses on repeatability rather than decorative finishes, so longevity in everyday shop use is prioritised. Seamless fit into inspection routines and traceable part checks Designed for straightforward integration in common metrology routines, the gauge pin suits go/no-go tests, plug gauges and ad hoc verification stations for end dimensions. Labelling and the SKU allow simple stock identification and traceability in quality records; the pin assists in establishing a reproducible reference that upstream and downstream teams can rely on. Backed by Metav’s positioning as a precision partner, the product supports lean inspection workflows and helps smaller operations access the measurement accuracy typically reserved for larger shops. Choose the Metav IndustryLine gauge pin when critical tolerances demand dependable reference measurement — contact Metav Werkzeuge in Emmerich for specialist advice and assured supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.274 GTIN: 4061905055393 eClass: 21170231 Facts Diameter: 2.74 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.005 kg Special features Material: Special steel Workshop version Single gauge pin for end-dimension checks FAQ What tolerance does the gauge pin provide? The M323.274 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm, suitable for very fine inspection and fit verification. Which applications suit this measuring pin? It is intended for end-dimension checks and hole inspection tasks where a compact 2.74 mm reference helps verify fit and clearance in assemblies. What material is used for the pin? The plug is made of special steel, selected to balance wear resistance and stable seating during repeated measurements. Is the M323.274 supplied as a single item or part of a set? This SKU is a single gauge pin supplied individually for insertion into inspection kits or fixtures. How does this pin support production quality? By providing a reproducible reference with tight tolerance, the pin reduces measurement variation and helps prevent rework and assembly issues. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.75mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ±0.001 mm repeatability, special steel stability and a compact 50 mm length for reliable end‑measure checks and streamlined workshop inspection workflows. Order directly via Metav Werkzeuge or consult the technical team for application support. Pin gauge, single — 2.75 mm, ±0.001 mm accuracy (Metav IndustryLine) The pin gauge, single 2.75 mm is a workshop‑grade end‑measure reference pin designed for precise gauging, quick go/no‑go checks and repeatable inspection tasks in mechanical and assembly environments. High-precision ±0.001 mm tolerance Special steel for stable dimensional integrity 50 mm overall length, compact design Supplied in protective transport case Reliable end‑measure references for repeatable inspection A workshop‑grade gauge pin with a ±0.001 mm tolerance provides a measurable improvement in process certainty for dimensional checks. The very small incremental deviation means the pin functions as a dependable reference when verifying bore sizes, plug gauges or mating features. By reducing measurement uncertainty, the pin contributes to fewer reworks and more consistent assembly acceptance rates, which translates into better throughput in production and inspection loops. Robust material and compact form suited to busy benches Constructed from special steel, the pin resists wear and preserves calibrated dimensions under frequent handling. The compact 50 mm overall length and 2.75 mm nominal diameter make it especially suited to confined inspection points and end‑measure tasks where access is limited. The workshop‑execution design balances stiffness with manoeuvrability so that operators can perform quick checks without compromising the integrity of the measured interface. Practical handling, protection and workflow traceability Delivery in a protective transport case ensures the gauge pin arrives ready for use and stays protected during storage or transit. The single‑unit configuration supports targeted replacements in tooling sets and simplifies inventory control. Clear labelling and the provided identifiers make it straightforward to include the item in existing quality documentation, improving traceability within metrology routines and supporting a structured inspection regime. For repeatable end‑measure confidence choose the Metav IndustryLine pin gauge M323.275 — contact Metav Werkzeuge for ordering or precise application advice via info@metav-werkzeuge.com or telephone +49 2822 7131930 Technical data Article number: M323.275 GTIN: 4061905055911 Material: Special steel Accuracy: ±0.001 mm Length: 50 mm Diameter: 2.75 mm Weight: 0.006 kg Packing: Protective transport case included Version: Workshop execution Category: Gauge pin (single) Facts Nominal diameter: 2.75 mm Overall length: 50 mm Tolerance: ±0.001 mm Weight: 0.006 kg Special features Single gauge pin for end‑measure tests Workshop execution for frequent use Protective transport case for handling and storage Category: Messstifte (gauge pins) Story trigger: end‑measure applications FAQ What is the declared tolerance of this gauge pin? The gauge pin is specified with a tolerance of ±0.001 mm, providing a high level of dimensional stability for exacting inspection tasks with the Metav IndustryLine M323.275. Is the pin suitable for routine workshop use? Yes; the workshop‑execution construction and special steel material make the pin robust enough for frequent handling and quick go/no‑go checks at the inspection bench. Does the item come with protective packaging? Delivery includes a protective transport case, ensuring the pin remains undamaged in transit and during storage. Can this gauge pin be used for calibration reference in quality documentation? The pin’s declared accuracy and clear identification make it suitable for inclusion in traceability records and routine inspection documentation within a quality system. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.76mm Test Pin ±0.001 mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade construction, sub-micron accuracy and compact handling to ensure reliable end‑measurement in the workshop; order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. M323.276 Pin Gauge (2.76 mm, ±0.001 mm) — Metav IndustryLine The M323.276 pin gauge is a single precision test pin designed for high‑accuracy end‑measurement and dimensional verification in workshop and inspection routines. Precision ±0.001 mm tolerance Diameter 2.76 mm, length 50 mm Workshop-grade special steel construction Compact single-pin format for end measurements Repeatable accuracy for end‑dimension checks The pin delivers a stated ±0.001 mm manufacturing tolerance, which translates into highly repeatable results when used as a reference for end‑measurements and fit checks. In practical terms, this level of precision supports tight quality requirements and helps to identify deviations at the micrometre scale, reducing the risk of assembly issues or rework. The specification is especially relevant where small clearance fits and interchangeability must be proven reliably. Robust build tailored to workshop use Constructed from special steel in a workshop execution, the pin balances wear resistance with straightforward handling. With a nominal diameter of 2.76 mm and a 50 mm overall length, the format is compact enough for quick manual checks yet long enough to reach recessed seats and short bores. The solid construction minimises deformation during normal use and contributes to consistent contact geometry, which in turn maintains measurement integrity over repeated cycles. Practical integration into inspection workflows This single‑pin format is intended for end‑measurement tasks such as final diameter verification, go/no‑fit checks and small‑bore gauging within production or service environments. The M323.276 can be incorporated into routine inspection sets or used as a trusted reference when validating machined components. Clear identification via GTIN and SKU simplifies traceability in stock lists and documentation, supporting transparent quality management and auditability. Contact Metav Werkzeuge today to clarify suitability for specific inspection tasks or to arrange supply of the M323.276 pin gauge directly from Emmerich — our specialists provide application guidance and reliable delivery. Technical data Article number / SKU: M323.276 GTIN: 4061905055928 Manufacturer: Metav IndustryLine Facts Diameter: 2.76 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg Special features Material: special steel Workshop execution Single pin delivery Intended use: end‑measurement and verification FAQ What level of precision does this pin achieve? The M323.276 pin gauge is manufactured to a tolerance of ±0.001 mm, providing micrometre‑class repeatability suitable for high‑precision end‑measurements. Is the pin suitable for routine workshop fitting checks? Yes, the workshop‑grade construction and compact 2.76 mm / 50 mm format make the pin well suited for daily fit and verification tasks on small bores and assemblies. How is the product identified for ordering and documentation? The pin is listed under SKU M323.276 with GTIN 4061905055928, simplifying inventory control and traceability. Which material is used for the pin? The gauge is produced from special steel, chosen for its balance of hardness and resistance to wear in typical workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.77mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high repeatability and workshop durability: the precise ±0.001 mm tolerance combined with a 2.77 mm gauge diameter and a 50 mm length ensures consistent end‑dimension checks and reduced rework. Order the gauge pin directly via Metav Werkzeuge or consult the team for specification matching. Gauge pin M323.277 — 2.77 mm diameter, ±0.001 mm tolerance The Gauge pin M323.277 is a workshop‑grade inspection pin designed for end‑dimension verification and fixture probing in precision assembly and quality control. Diameter 2.77 mm precision pin Tolerance ±0.001 mm for exact gauging 50 mm length for probe and fixture use Workshop‑grade special steel construction Reduce measurement uncertainty with sub‑micron repeatability This inspection pin delivers a measured tolerance of ±0.001 mm, enabling reliable go/no‑go checks and tight dimensional control on small bores and component ends. The extremely fine tolerance reduces the need for secondary checks and helps shorten inspection cycles in repetitive production. By using a stable gauge diameter of 2.77 mm, setup variance is minimised, which supports faster decision‑making on the shop floor and a more efficient quality workflow. Built for everyday workshop handling and repeat use Constructed from special steel and specified as a workshop‑grade item, the pin withstands routine handling and repetitive seating in gauges and fixtures without rapid wear. The material choice balances hardness and machinability to keep contact surfaces intact while preserving the reference diameter. Robust construction ensures dimensional stability over many inspection cycles, which translates into dependable readings and fewer rejected parts due to measurement artefacts. Practical form factor for fixture access and traceability With a 50 mm length the pin provides sufficient reach for recessed features and can be used as a fixed reference in modular checking rigs. Supplied as a single item, it integrates easily into bespoke inspection assemblies as an end‑stop or probe. Traceability is supported by the assigned SKU and GTIN, aiding inventory control and quality documentation for batch records and process audits. Contact Metav Werkzeuge for tailored advice on integrating this workshop‑grade gauge pin into inspection routines or to request batch availability and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.277 GTIN: 4061905055935 Label: Gauge pin, single, 2.77 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.77 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.006 kg ECLASS: 21170231 Special features Material: special steel Supply: single piece Execution: workshop‑grade Category: gauge pins FAQ What is the intended use of this gauge pin? The gauge pin M323.277 from Metav IndustryLine is intended for end‑dimension verification, fixture probing and simple go/no‑go gauging tasks in production and inspection environments. Is the tolerance of ±0.001 mm achievable in daily shop use? Yes, when used with stable fixturing and calibrated reference equipment the ±0.001 mm tolerance of this Metav IndustryLine gauge pin can be maintained for routine checks. Can this pin be used in modular checking fixtures? The 50 mm length and precise 2.77 mm diameter make the pin suitable for integration as an end‑stop or probe in modular and bespoke checking fixtures. How is the material specified and what does it mean for wear? The pin is made of special steel, a balanced choice that offers good wear resistance for workshop applications while maintaining the reference diameter over many cycles. What identifiers support traceability for audits and reorders? Traceability is provided via SKU M323.277 and GTIN 4061905055935, enabling straightforward inventory management and documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com