Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
2.05mm Gauge Pin 50mm Length ±0.001mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra-fine one-micron tolerance, a compact 50 mm length and robust workshop construction for reliable end measurements; order directly via Metav Werkzeuge or request technical advice from our specialists. M323.205 gauge pin — 2.05 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.205 gauge pin is a workshop-grade inspection pin designed for precise end measurements and integration into fixtures and jigs. Ultra-fine tolerance ±0.001 mm Diameter nominal 2.05 mm Length 50 mm for end measurements Workshop-grade special steel construction Dependable one‑micrometre accuracy for quality control The inspection pin delivers a certified mechanical tolerance of ±0.001 mm, corresponding to a resolution at the 1 µm level that supports high-precision go/no-go checks and micrometric inspections. Such repeatable accuracy reduces measurement uncertainty in sampling and control operations, enabling faster decisions on conformity. The narrow tolerance makes this pin particularly suitable where dimensional consistency is critical, for example when validating pin gauges, assembly fits or small-bore seating in routine workshop inspections. Robust workshop construction that withstands daily use Built as a workshop-grade item from special steel, the pin combines wear resistance with consistent performance under regular handling. The material choice gives a reliable surface that resists deformation during insertion and withdrawal, which in turn preserves the geometric integrity of the nominal 2.05 mm diameter over many cycles. The compact weight and balanced geometry facilitate safe manual handling and make the component easy to seat in fixture pockets or controlled instrument holders. Compact form for precise end‑measurement applications At a length of 50 mm and a nominal diameter of 2.05 mm, the pin is optimised for end‑measurements and tight‑tolerance checks in small assemblies. Its small form factor allows straightforward integration into test rigs and makes it a practical choice for bench inspection tasks and inline fixtures alike. The low mass contributes to controlled insertion dynamics, helping to avoid measurement artefacts from impact or excessive force while delivering consistent contact conditions across repeated checks. For technical advice or to request the M323.205 from the Metav IndustryLine range, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.205 GTIN: 4061905054471 Brand: Metav IndustryLine Core specifications Diameter: 2.05 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Features Material: special steel Workshop version Supplied individually Application: end measurements FAQ What tolerance does this gauge pin offer? The M323.205 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.001 mm, suitable for micrometric inspection tasks. What material is used for the pin? This inspection pin is manufactured from special steel, chosen for its wear resistance and stability under workshop conditions. For which applications is this pin intended? The pin is intended for end measurements, fixture checks and small‑bore inspections where a nominal 2.05 mm diameter and one‑micrometre tolerance are required. Can the pin be used in inspection jigs and fixtures? Yes — the 50 mm length and compact form factor make the pin suitable for integration into test rigs and bench fixtures in routine quality control. How is the product identified for ordering? Order reference is SKU M323.205; the product is listed under the Metav IndustryLine range and carries GTIN 4061905054471. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.06mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Reliable inspection requires both fine tolerance and durable construction: benefit from the combination of a ±0.001 mm tolerance, special steel hardness and a practical protective case for safe transport; order the gage pin directly via Metav Werkzeuge or ask our consultants for application advice. Gage pin M323.206 — 2.06 mm, ±0.001 mm, 50 mm The Gage pin M323.206 is a precision measuring pin for verifying end dimensions and bore fits in workshop metrology, designed as a robust workshop version for routine inspection tasks. High-precision ±0.001 mm tolerance Diameter 2.06 mm for tight bore checks Length 50 mm workshop design Delivered in protective case Precision where measurement matters A finely matched tolerance is the core benefit when checking bore sizes or end dimensions. The ±0.001 mm specification guarantees a high level of reproducibility for pass/fail checks and comparative inspections, reducing guesswork during quality control. For everyday workshop routines, a narrow tolerance helps to avoid rework and scrap by making acceptance criteria clear and repeatable. Robust workshop design for repeated handling Engineered as a workshop-grade instrument, the pin uses special steel to withstand frequent use and handling. The 50 mm length offers a secure grip and adequate engagement depth for most small-bore verifications, while the compact mass facilitates quick positioning. Delivery in a protective case ensures safe transport between benches or job sites, protecting the measuring surface from knocks and contamination that could otherwise affect accuracy. Simple integration and traceability in inspection workflows The test pin is suitable for quick plug checks, end-dimension verification and assembly validation in production and maintenance settings. Marked and traceable with SKU M323.206 and GTIN details, the component can be recorded in inspection logs and inventory systems for audit-friendly traceability. The compact geometry and industry-standard dimensions allow easy use with comparison fixtures and visual inspection jigs, improving throughput without complex set-up. Choose the Metav IndustryLine M323.206 for dependable bore verification and contact Metav Werkzeuge GmbH in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for availability and expert guidance Technical data SKU: M323.206 GTIN: 4061905054488 Manufacturer: Metav IndustryLine Facts Diameter: 2.06 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg ECLASS: 21170231 Special features Workshop version Delivered in protective case for transport Material: special steel Suitable for verification of end dimensions and bore fits FAQ What tolerance is specified for this gage pin? The gage pin is specified to ±0.001 mm, offering high repeatability for precise bore and end-dimension checks with SKU M323.206. Which materials is the pin made from? The pin is made of special steel, selected for wear resistance and durability under frequent workshop use. Is the pin supplied ready for transport? Yes, the item is delivered in a protective case intended for safe transport and to preserve the measuring surface. For which inspection tasks is this pin best suited? This pin is ideal for plug checks, verification of end dimensions and quick bore checks in production and maintenance environments. How can this test pin be recorded for traceability? Use the SKU M323.206 and GTIN 4061905054488 in inspection logs and inventory systems to maintain traceable records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.07mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Taking advantage of high repeatability, submicrometre tolerance and a compact length, this test pin ensures repeatable dimensional checks in workshop and inspection tasks; combine robustness and precision for smoother quality routines. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.207 — 2.07 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.207 is a single test pin designed for precise dimensional inspection and fixture setting across metrology and production environments. Workshop-grade construction Diameter 2.07 mm with ±0.001 mm tolerance Length 50 mm for compact checks Supplied as a single test pin Reliable precision for routine inspection The compact gauge element delivers a 2.07 mm nominal diameter with an exceptional ±0.001 mm tolerance, making it suitable where tight limits are required in small bores or pin gauges. Manufactured as a workshop-grade tool, the component supports consistent pass/fail assessment and short-cycle quality checks. The combination of close tolerance and moderate length reduces deflection risk during use, which translates into fewer measurement repeats and more efficient inspection throughput. Robust material and practical handling Constructed from special steel, the pin balances surface hardness with corrosion resistance to withstand frequent handling and insertion cycles on the shop floor. The 50 mm length is intentionally compact to suit fixture set-up, gauge blocks and pin plates while keeping handling simple. At approximately 0.004 kg, the part is easy to position and integrate into existing inspection jigs. The solid design minimises burr-related errors and affords long-serving dimensional stability under normal workshop conditions. Integration into quality workflows As a single-item solution, the component is well suited for selective checks, calibration aids and fixture references where a dedicated nominal diameter is required. Traceable identification via SKU and GTIN facilitates stock control and documentation in quality management systems, while the clear specification supports supplier audits and inspection planning. Metav IndustryLine provides the necessary product data for procurement and inspection documentation to maintain repeatable measurement routines. For workshop-grade dimensional control, contact Metav Werkzeuge in Emmerich to secure the M323.207 gauge pin and discuss supply options or technical details. Technical data Article number: M323.207 GTIN: 4061905054495 Manufacturer: Metav IndustryLine Facts Diameter: 2.07 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Version: Workshop version Delivery form: single test pin Category: Gauge pins FAQ What is the primary use of this test pin? The M323.207 is intended for precise dimensional checks, fixture setting and selective inspection tasks where a defined nominal diameter of 2.07 mm is required. How accurate is the pin for quality checks? The pin is specified with a tolerance of ±0.001 mm, suitable for tight tolerance checks and applications that demand sub-micrometre repeatability. What material is the pin made from and is it durable? The component is made from special steel and delivered in a workshop-grade design, giving good wear resistance and durability for regular use in production environments. Is a calibration certificate supplied with this item? No calibration certificate is specified in the product data for this item Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.08mm Gauge Pin Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
The combination of high repeatability, submicron tolerance and a compact 50 mm form factor ensures reliable end‑measure checks and straightforward integration into workshop test fixtures. Order the gauge pin directly via Metav Werkzeuge or consult the team for specification matching. Gauge pin M323.208 — 2.08 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) A single, precision gauge pin designed for exact end‑measure references and workshop inspection tasks, supplied as an individual test pin for fixture setting and quality control. Workshop version for robust handling Diameter 2.08 mm with ±0.001 mm accuracy 50 mm special-steel construction Reliable reference for repeatable measurements The M323.208 gauge pin provides a stable reference for end‑dimension verification and fixture alignment. Manufactured in a workshop execution, the pin combines compact geometry with machining that prioritises consistent contact surfaces; this results in repeatable positioning when used for plug checks or in assembly jigs. The documented ±0.001 mm tolerance supports narrow acceptance windows in precision production and reduces the risk of rework caused by measurement variation. Precision explained and practical benefits A declared tolerance of ±0.001 mm places the gauge pin in a high‑precision category suitable for fine inspection tasks and fit verification. In practice, this means the pin can be used to establishing reference points where dimensional certainty is critical; the tight tolerance reduces measurement uncertainty and supports faster decision‑making in process control. The small diameter of 2.08 mm and the 50 mm length make the component especially suitable for compact bores, dowel checks and contact probing where minimal intrusion and high positional accuracy are required. Durable material and workshop suitability Constructed from special steel, the pin combines surface hardness with resistance to wear typical of workshop environments; this supports sustained dimensional integrity over repeated use. The single‑piece supply, low mass (approx. 0.004 kg) and precise machining enable easy handling and rapid interchange in test setups. The robust finish and geometry are tailored to withstand regular insertion without immediate loss of accuracy, supporting consistent inspection routines and minimising machine downtime. For reliable workshop calibration and procurement of the Metav IndustryLine M323.208 gauge pin, contact Metav Werkzeuge for ordering and technical guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.208 GTIN: 4061905054501 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 2,08mm, +/- 0.001 mm Länge 50 mm Numerical data Diameter: 2.08 mm Length: 50 mm Declared accuracy: ±0.001 mm Weight: 0.004 kg Materials & features Material: Special steel Delivery: Single gauge pin Version: Workshop execution Intended use: End‑measure reference / fixture and inspection tasks FAQ What tolerance does the gauge pin have? The gauge pin is specified with an accuracy of ±0.001 mm, allowing high‑precision end‑measure checks with narrow acceptance limits. Which materials is the M323.208 suitable for inspecting? The M323.208 gauge pin is a reference component for dimensional checks and is applicable when verifying bores, dowel seats and fixture positions irrespective of workpiece material. Is the pin supplied as a single item or in sets? This article is supplied as a single gauge pin (individual delivery); the designation and SKU are M323.208. How durable is the material under frequent use? Made from special steel, the pin is produced for workshop environments and offers wear resistance appropriate for repeated insertion and inspection cycles. Can the M323.208 be used for precision probing in measuring machines? Yes; the small diameter and tight tolerance make the gauge pin suitable as a contact reference for manual and machine‑assisted inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.09mm Gauge Pin, Workshop Version, ±0.001mm Accuracy, 50mm Length - Metav IndustryLine
Take advantage of the combination of ±0.001 mm accuracy, a compact 2.09 mm diameter and a robust 50 mm length for reliable small‑bore inspection and repeatable end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult the technical team for application advice. M323.209 Gauge pin (2.09 mm, ±0.001 mm) – Metav IndustryLine The M323.209 gauge pin is a single, high‑precision inspection pin designed for small‑bore verification and end‑measurements in workshop and inspection environments. High accuracy ±0.001 mm 2.09 mm diameter for fine bores 50 mm length for reliable reach Workshop version for robust handling Highest measurement confidence for small bores Engineered for tasks where small dimensional deviations matter, this pin delivers a ±0.001 mm positional tolerance that classifies it as a high‑precision inspection tool. Such tolerance helps reduce rejects and rework by providing a clear go/no‑go reference for tight fits. The fine 2.09 mm diameter makes it suitable for verification of small holes, plug gauges and end stops where conventional gauges are too coarse. Durable design that supports everyday metrology Constructed from special steel and specified as a workshop version, the pin combines surface hardness with a finish optimised for repeatable contact. The 50 mm length provides sufficient reach for many bench and fixture checks while maintaining stiffness to avoid deflection. These properties translate into reliable measurements over many cycles and minimise downtime linked to premature wear. Practical use in inspection and production workflows Ideal for inspection benches, jigs and assembly verification, the single‑piece pin simplifies inventory and traceability in quality processes. Its compact form factor allows easy integration into gauge sets and takedown checks. The robust construction supports frequent handling in production areas, and the clearly defined tolerance assists metrology teams in documenting conformity during incoming inspection and in‑process checks. For specialist advice or to arrange supply of the M323.209 gauge pin, contact Metav Werkzeuge in Emmerich for tailored technical guidance and prompt delivery. Technical data Article number: M323.209 GTIN: 4061905054518 Manufacturer: Metav IndustryLine Facts Diameter: 2.09 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Workshop version Single test pin FAQ What is the primary use of this gauge pin? The M323.209 gauge pin is intended for small‑bore verification and end‑measurement tasks in workshops and inspection areas. What precision class does the pin belong to? With a tolerance of ±0.001 mm, the pin falls into the high‑precision inspection category suitable for fine metrology checks. Which materials is the pin suitable for when used as a reference? The pin serves as a dimensional reference for bore and end‑measure checks and can be used alongside components made from a wide range of materials; selection of mating materials should follow usual metrological practice. Is the M323.209 suitable for integration into gauge sets? Yes, its compact form and defined length make it suitable for gauge sets, fixtures and inspection benches where small‑bore references are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.10mm Test Pin Single ±0.001 mm Accuracy Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometre-grade accuracy, robust workshop design and practical transport packaging for reliable end-dimension checks. Order the gauge pin directly via Metav Werkzeuge or ask the Metav consultants for application advice. Metav IndustryLine gauge pin M323.210 — 2.10 mm, ±0.001 mm, 50 mm length A Metav IndustryLine gauge pin for precise end-dimension verification in workshop and inspection environments, designed as a single-piece, workshop-grade test pin for micromechanical checks. Workshop version for durable everyday use Diameter 2.10 mm with ±0.001 mm tolerance 50 mm length for end-dimension verification Supplied in transport case for secure handling Measure end dimensions with micrometre-class certainty A test pin with a nominal diameter of 2.10 mm and a tolerance of ±0.001 mm delivers measurable, repeatable outcomes for tight-fit and finishing checks. The listed tolerance is a technical specification that directly reduces uncertainty in go/no-go assessments and gauge-based inspection routines. Where component fits matter, the reduced dimensional scatter shortens decision loops in production control and lowers the risk of rework. The combination of small diameter and fine tolerance positions this pin within the micro-range expected for precision bench and component work. Built for the workshop: robust material and safe transport Constructed from special steel and rated as a workshop version, the pin tolerates routine handling while retaining its measuring geometry. The 50 mm overall length provides adequate grip for insertion and withdrawal without compromising alignment when checking bores or mating parts. Delivery in a transport case (plastic or wooden) protects the gauge during storage and transit, preserving the measured surface and minimising the need for frequent rework or replacement. The single-piece format simplifies handling and reduces potential assembly errors that could otherwise affect measurement consistency. Practical integration into inspection workflows This precision test pin is intended for end-dimension and fit verification on small bores, jigs, and assembled components. Traceability is supported by the product identifiers included in the technical data, enabling simple inventory control and record-keeping for quality systems. As a compact measuring implement, it complements bench calipers and micrometres by providing a direct physical reference for mating features, accelerating in-process checks and pass/fail assessments. The design focuses on a single, well-defined task—reliable verification of critical diameters—so inspection steps remain straightforward and efficient. For application guidance or to source the Metav IndustryLine gauge pin M323.210 for your inspection bench, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss suitability and delivery options Technical data Article number: M323.210 GTIN: 4061905054525 Weight: 0.004 kg Material: Special steel Nominal diameter: 2.10 mm Tolerance: ±0.001 mm Length: 50 mm Facts Diameter (nominal): 2.10 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg GTIN: 4061905054525 Special features Workshop version Single-piece gauge pin Supplied in transport case (plastic or wood) for secure handling Intended for end-dimension verification FAQ What tolerance does this gauge pin offer? The gauge pin provides a tolerance of ±0.001 mm, enabling micrometre-level control for end-dimension checks. Is the pin suitable for routine workshop use? Yes; the workshop-grade construction and special steel material make the pin robust enough for regular inspection tasks. What is the length and how does that affect handling? At 50 mm length the pin offers a practical balance between handling comfort and measurement stability for manual checks. Can this pin be used for go/no-go checks on small bores? It is suitable for direct diameter verification and go/no-go style assessments where a 2.10 mm reference is required. How is the product identified for inventory and traceability? The product is listed as Metav IndustryLine gauge pin M323.210 with GTIN 4061905054525 for straightforward traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.11mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of industrial accuracy and workshop durability: the M323.211 precision gauge pin delivers a ±0.001 mm tolerance on a 2.11 mm diameter with a 50 mm functional length, enabling reliable end-dimension checks in routine quality control. Order directly via Metav Werkzeuge or consult our advisors for application support. M323.211 — precision gauge pin, 2.11 mm diameter, ±0.001 mm (Metav IndustryLine) The M323.211 is a single precision gauge pin designed for end-dimension verification and small-part inspection in workshop and laboratory quality-control environments. Workshop version for rugged everyday use Diameter 2.11 mm with ±0.001 mm tolerance 50 mm functional length for deep measurements Supplied in transport case for secure storage Accurate control for repeatable quality A gauge pin with a ±0.001 mm tolerance provides sub-micron-level repeatability that supports tight production tolerances and reduces scrap rates. The very small diameter of 2.11 mm makes this instrument suitable for fine bores and micro features where standard plugs cannot access. By offering a defined reference diameter and a stable length of 50 mm, the pin enables consistent pass/fail checks and comparative measurements that align with industrial metrology practices, improving process control and reducing measurement uncertainty. Built for workshop handling and longevity Manufactured from special steel and specified as a workshop version, the pin balances hardness and corrosion resistance to withstand frequent use. The compact mass and slim geometry allow easy handling during rapid inspection routines, while the supplied transport case protects the gauge during storage and transit. Robust design minimises deformation risk during everyday use, giving reliable reference points across many inspection cycles and supporting efficient inspection flows in busy production environments. Micro-class suitability and application scenarios With a maximum measuring range of 2.11 mm, this pin falls into the micro class of measuring tools, developed for fine mechanical assemblies, micro components and precision fixtures. Typical uses include verification of small-bore diameters, calibration of holding fixtures, end-dimension checks for turned parts and comparative gauging in inspection benches. The compact dimensions and high tolerance make the instrument a practical choice where tight fits and fine geometries are common. Practical integration and operational benefits The instrument's simple geometry allows straightforward use with common gauging procedures: insert for go/no-go checks, reference against calibrated master gauges or employ as a datum in manual measurement setups. Because the component is supplied ready for workshop use, it integrates quickly into existing inspection routines and reduces setup time. Complementary documentation and Metav's advisory services are available for users seeking to incorporate the pin into quality-control plans or to specify compatible fixtures. Choose the Metav IndustryLine precision gauge pin for controlled micro-dimension checks and contact Metav Werkzeuge in Emmerich for ordering and technical guidance: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.211 GTIN: 4061905054532 Brand: Metav IndustryLine Facts Diameter: 2.11 mm Tolerance / accuracy: ±0.001 mm Functional length: 50 mm Weight: 0.004 kg Special features Material: special steel Workshop version Supplied in transport case Category: gauge pins (Messstifte) FAQ What level of accuracy does this gauge pin provide? The M323.211 gauge pin from Metav IndustryLine is specified to ±0.001 mm, making it suitable for high-precision end-dimension checks. Is the pin suitable for use in a production workshop? Yes, the workshop version is made from special steel and supplied in a transport case for protection, designed for routine use on production benches. Which applications are best suited to this gauge pin? Compact bores, micro components and end-dimension verification are ideal applications; the 2.11 mm diameter and 50 mm length support checks in fine mechanical assemblies. Can the pin be used as a reference for fixture setup? Yes, the pin’s tight tolerance and stable length make it suitable as a reference datum for fixture calibration and comparative gauging tasks. What protective packaging is provided with the product? Delivery includes a transport case to protect the gauge pin during storage and handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.12mm Gauge Pin Precision ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
The combination of ±0.001 mm measurement accuracy, a compact 2.12 mm diameter and a robust 50 mm length ensures reliable end‑measurement and repeatable checking results; order the gauge pin directly via Metav Werkzeuge or consult our specialists for integration advice. Gauge pin M323.212, single 2.12 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) A gauge pin M323.212 designed for precision end‑measurement and go/no‑go checking in workshop and production quality control ±0.001 mm measurement accuracy 2.12 mm hardened special-steel pin 50 mm compact length for easy handling Cut inspection time with traceable precision The compact pin is engineered to deliver high repeatability through a manufacturing tolerance of ±0.001 mm, which reduces uncertainty in routine checks and accelerates go/no‑go decisions on the shop floor. A defined diameter of 2.12 mm and a consistent 50 mm length mean the part suits fixture reference points and microscopic fits without the need for frequent compromise adjustments. This measurable precision translates into fewer rechecks and higher throughput during batch acceptance and first‑article inspections. Built for daily workshop use and robust handling Constructed from special steel and finished for workshop execution, the pin resists wear under standard use while maintaining its measurement integrity. The compact 50 mm dimension improves ergonomics when handling small parts or when used inside confined fixtures, enabling quick placement and removal. The straightforward single‑pin format simplifies stocking and replacement; maintenance teams benefit from a durable, easily exchanged reference component that keeps inspection points operational. Easy integration into quality procedures and fixtures Designed as a practical measuring tool, the pin integrates smoothly into comparative checks, plug‑gauge arrays and fixture verification routines. Its clear numeric specification—diameter, length and tolerance—supports traceable documentation in quality reports and process control sheets. For shops adopting systematic quality measures, the pin offers an economical way to establish stable reference points without elaborate calibration requirements noted in the product data. For application advice or to confirm compatibility with specific jigs or measuring stations, Metav’s technical advisers are available to provide guidance. For purchasing or technical advice on the Metav IndustryLine gauge pin M323.212, contact Metav Werkzeuge directly by phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for production and delivery options Technical Data Article number: M323.212 GTIN: 4061905054549 SKU: M323.212 Brand: Metav IndustryLine Facts Diameter: 2.12 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Workshop execution Single gauge pin Category: Gauge pins FAQ What level of accuracy can be expected from the gauge pin? The gauge pin M323.212 is specified with a tolerance of ±0.001 mm, offering precision suitable for fine inspection tasks and reliable go/no‑go checks. Which materials is the pin made from? The M323.212 is manufactured from special steel and finished for workshop use to provide wear resistance and stable measurement performance. Is the pin supplied as a single item or in a set? This listing describes the gauge pin supplied individually as a single unit (SKU M323.212). Can the pin be used inside fixture assemblies and plug‑gauge checks? Yes. The defined 2.12 mm diameter and 50 mm length make the pin suitable as a reference element in fixtures, plug‑gauge arrangements and comparative inspection setups. Are calibration certificates included with the pin? The product data does not specify a calibration certificate; please contact Metav Werkzeuge for details on calibration services or certificate options. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.13mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of workshop-grade 2.13 mm gauging with ±0.001 mm repeatability and robust special-steel construction for dependable end‑size checks; order directly via Metav Werkzeuge or consult the team for application advice. Pin gauge, single, 2.13 mm, ±0.001 mm, length 50 mm — Metav IndustryLine The pin gauge, single, 2.13 mm is a workshop-grade inspection pin designed for precise end‑size and fit verification in metalworking and precision assembly. Workshop-grade construction Diameter 2.13 mm ±0.001 mm Length 50 mm for compact inspections Special-steel construction Consistent metrology for repeatable end‑size checks The gauge pin delivers ±0.001 mm positional consistency, making it suitable where tight tolerances determine part acceptance. With a diameter of 2.13 mm and a solid 50 mm length, the component provides a measurable reference for plug fits, bore verification and comparative checks. Such a fine tolerance translates into measurable process reliability: production decisions based on this reference reduce rework and avoid downstream quality issues. The small form factor also supports use in confined inspection fixtures and bench routines without sacrificing stiffness or contact stability. Robust workshop design that stays dimensionally stable Built from special steel, this single inspection pin is specified for frequent workshop use where handling and contact wear must be controlled. The workshop‑grade construction reduces the risk of surface damage under repeated insertion and extraction cycles, preserving roundness and diameter integrity over time. At approximately 0.004 kg, the pin remains easy to position in fixtures and gauge blocks while offering sufficient mass for stable contact. The combination of material choice and compact geometry supports a long service life and predictable measurement behaviour. Practical benefits for production and inspection workflows Using a dedicated inspection pin streamlines routine verifications: quick go/no‑go testing, comparative gauging and fit assessments become straightforward and reproducible. The clear numerical specification and traceable SKU simplify inventory and quality documentation—supporting lean inspection routines and orderly tool management. Where accuracy matters, a defined reference such as this pin reduces subjective judgement and speeds up decision cycles on the shop floor, contributing directly to throughput and fewer rejects. Contact Metav Werkzeuge for tailored guidance on integrating the Metav IndustryLine pin gauge M323.213 into existing inspection routines; expert advice and procurement assistance are available from Emmerich. Technical data Article number: M323.213 GTIN: 4061905055232 Material: Special steel Label: Pin gauge, single, 2.13 mm, ±0.001 mm, length 50 mm Facts Diameter: 2.13 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg ECLASS: 21170231 Special features Workshop execution Single test pin configuration SKU: M323.213 Story trigger: endmasse FAQ What tolerance can be expected from this inspection pin? The pin gauge is specified with a tolerance of ±0.001 mm; the Metav IndustryLine pin gauge M323.213 is intended for high‑precision end‑size checks where such repeatability is required. Which applications suit a 2.13 mm gauge pin? Small bore verification, plug‑fit checks, fixture setup and compact assembly inspection benefit from a 2.13 mm diameter pin, providing a clear reference for acceptance testing. Is the pin suitable for routine workshop use? Yes — the workshop‑grade construction and special‑steel material make the pin robust enough for frequent insertion and extraction in daily inspection routines. How is the pin identified for stock and quality records? The inspection pin is supplied as SKU M323.213 with GTIN 4061905055232 for unambiguous inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.14mm Gauge Pin Length 50mm ±0.001mm Workshop Finish - Metav IndustryLine
Take advantage of ultra-fine dimensional control with a 2.14 mm diameter and ±0.001 mm positional accuracy, combined with a compact 50 mm length and workshop-grade construction for consistent fit checks. Order this gauge pin directly via Metav Werkzeuge or consult our advisors for tailored supply. M323.214 Gauge Pin — 2.14 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.214 gauge pin offers micro‑range diameter verification for fine mechanical and end‑dimension checks in workshop environments ±0.001 mm tolerance Diameter 2.14 mm nominal Length 50 mm workshop design Made from special steel Precision that minimises rework and speeds inspection A nominal diameter of 2.14 mm combined with a tight ±0.001 mm tolerance (one micrometre) provides the dimensional certainty required for high‑accuracy go/no‑go checks and final inspection steps. The compact 50 mm length keeps the contact area stiff and reduces deflection during insertion, so repeatable results are achieved rapidly. This level of precision translates directly into lower scrap rates and fewer assembly mismatches, delivering a clear cost‑efficiency argument for production and quality teams. Designed for reliable fit checks and end‑dimension control Used as a reference pin in gauges, fixtures or as an end‑diameter master, this precision pin supports fast verification of bore sizes and assembly fits. The special steel construction gives consistent surface finish and contact behaviour, which is essential when working at micron‑scale tolerances. The workshop execution emphasises practical handling: small mass and compact geometry suit both hand operation and use within checking rigs, enabling efficient inspection cycles without complex setup. Practical durability for daily workshop use Although compact, the pin is manufactured to withstand routine handling in production environments. The workshop design ensures robustness where frequent insertion and withdrawal occur, while the small overall weight supports quick tool changes and minimal inertia in automated gauge heads. For quality engineers and toolroom technicians, the combination of fine nominal diameter and robust execution makes this item a dependable reference for dimension control in micro‑mechanical contexts. For micro‑precision gauging with 1 µm repeatability, contact Metav Werkzeuge GmbH in Emmerich to arrange supply or discuss application details — eMail: info@metav-werkzeuge.com • Phone: +49 2822 7131930 Technical Data SKU: M323.214 GTIN: 4061905055249 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 2,14mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.14 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Measurement range (max): 2.14 mm Special features Material: Special steel Workshop execution Application: End‑dimension and fit checks Story trigger: end dimensions FAQ What tolerance can be expected from this gauge pin? The M323.214 gauge pin is specified with a tolerance of ±0.001 mm, corresponding to 1 µm accuracy for high‑precision fit verification. Is the pin suitable for use in fixture gauges and plug checks? Yes, the precision pin is intended for fixture and plug checks where micro‑scale diameter control and repeatable insertion are required. What material is the pin made from and why does it matter? The pin is made from special steel, chosen to ensure consistent surface quality and contact behaviour during repeated measurements and fit tests. Can this pin be used in automated measuring stations? Its compact 50 mm length and low mass make the pin suitable for both manual and automated gauge heads designed for micro‑range diameter verification. How is the item identified for ordering or inventory? Order or reference this product by its SKU M323.214 or GTIN 4061905055249; both identifiers are listed above for procurement and inventory control. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.15mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Benefit from absolute measuring confidence thanks to the combination of ultra‑fine tolerance, compact dimensions and a robust workshop finish; this pin is intended for repeatable end‑measurement tasks and fixture reference points. Order the M323.215 gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.215 Gauge Pin — 2.15 mm, 50 mm, ±0.001 mm (Metav IndustryLine) The M323.215 gauge pin is a single precision inspection pin designed for end‑measurement, go/no‑go verification and fixture referencing in workshop and production metrology. Ultra‑fine tolerance ±0.001 mm Compact 2.15 mm diameter for fine bores 50 mm length for extended datum reach Workshop version with transport case Achieve repeatable end‑measurement with micrometre‑grade tolerance The small, solid inspection pin provides an ultra‑fine tolerance of ±0.001 mm, delivering micrometre‑level confidence when establishing reference points or checking bore sizes. Manufactured for workshop environments, the pin’s dimensional stability reduces measurement scatter and helps lower scrap rates in serial inspection. Tight tolerance control makes this tool especially suitable for precision end‑measurements and verifying hardened bore diameters where reproducibility is essential. Compact form factor that fits confined assemblies With a 2.15 mm diameter and 50 mm length, the pin is tailored for measuring small bores, locating holes in assemblies and acting as a reference mandrel in jigs. The slender profile allows access to narrow features without compromising stiffness for short to medium reaches. This compact geometry also facilitates hand‑held probing and integration into gauge blocks or fixture systems where space is restricted. Durable material and workshop configuration for daily use Constructed from special steel and specified as a workshop version, the pin resists wear under regular contact inspection and retains edge definition for longer periods. The robust finish is optimised for handling and frequent insertion cycles, reducing the need for premature replacement and ensuring consistent contact geometry during measurement operations. Designed for integration into inspection routines As an end‑measurement artifact, the pin serves both as a direct measuring probe and as a reference element within inspection jigs. Its defined nominal diameter supports repeatable go/no‑go checks and positional calibration. The combination of small diameter and precise length makes the item suitable for fine mechanical parts, toolmaking and quality control stations that require compact, high‑accuracy gauges. Protected delivery and practical handling The item is supplied in a transport case, ensuring protection during storage and transit and simplifying organisation within a tool crib. The packaging choice supports safe handling for small, precision parts and reduces the risk of surface damage that would otherwise affect measurement reliability. Traceable identification for production use Each pin is shipped with clear identification to support traceability in the quality process. The compact design and workshop specification mean the pin is an unobtrusive yet reliable addition to standard inspection sets and fixture references, contributing to stable production tolerances and fewer non‑conforming parts. For traceable end‑measurement and fixture reference tasks, request the Metav IndustryLine M323.215 gauge pin from Metav Werkzeuge and speak with our technical advisors to confirm fit‑up and application suitability. Technical data Article number: M323.215 GTIN: 4061905055256 Manufacturer: Metav IndustryLine Facts Diameter: 2.15 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: special steel Workshop version Delivered in transport case Single gauge pin for end measurements FAQ Is this gauge pin suitable for bore inspection and end‑measurement? Yes. The M323.215 gauge pin is intended for end‑measurement, bore checks and as a reference pin in fixtures where micrometre‑grade tolerance is required. What accuracy and repeatability can be expected? The inspection pin is specified to ±0.001 mm, offering high repeatability for fine measurement tasks and go/no‑go verifications. What are the exact dimensions of the pin? The pin measures 2.15 mm in diameter and 50 mm in length, providing a compact profile with extended reach for small features. What material is used and how is it supplied? Manufactured from special steel in a workshop finish and supplied in a transport case to protect the contact surfaces during storage and transit. Can the pin be used as a reference in jigs and fixtures? Yes. The dimensional stability and compact diameter make this pin suitable as a reference or locating element in inspection jigs and production fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.16mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometric accuracy, compact dimensions and robust workshop design for reliable end‑dimension checks and repeatable inspection results. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. M323.216 Precision Gauge Pin (Ø 2.16 mm, ±0.001 mm) — Metav IndustryLine A M323.216 precision gauge pin designed for end‑dimension verification and workshop inspection tasks; single pin, diameter 2.16 mm with a 50 mm length for accessible component checks Micrometric tolerance ±0.001 mm Ø 2.16 mm hardened special steel pin 50 mm length for end‑dimension inspection Workshop execution for everyday use Consistent micrometric reference for critical checks The M323.216 delivers a ±0.001 mm tolerance that positions it among high‑precision reference pins. Such a fine tolerance corresponds to a 1 µm deviation margin, enabling tight go/no‑go assessments and precise end‑dimension verification on small bores or locating holes. By using a defined diameter of 2.16 mm, the pin provides a clear, repeatable datum for comparative measurements and go/no‑go testing. The accuracy specification supports statistical process control by reducing measurement scatter and improving the reliability of inspection data. Durable workshop design that withstands routine handling Constructed from special steel, this pin balances hardness and corrosion resistance for repeated use in production and workshop environments. The workshop execution indicates reinforced finishing and dimensional stability under handheld and fixture use, so checks remain reproducible across shifts. With a 50 mm shank length, the geometry is long enough to engage through a workpiece while short enough to avoid excessive bending or vibration, maintaining repeatability during manual insertion and fixture mounting. Straightforward integration into inspection workflows As a single‑piece precision reference, the pin simplifies calibration and setup routines: it functions as a direct reference for end‑dimension checks, alignment of fixtures or verification of locating holes. The compact form factor allows use in bench comparators, pin holders or bespoke gauges without significant modification to existing inspection jigs. Because the pin is specified to tight limits, adoption often reduces setup time and the need for frequent rechecks, supporting faster throughput in routine quality control. Supply reliability and a partner for precision Sourcing through Metav IndustryLine combines product consistency with logistical dependability. Metav’s position as a precision specialist and its broad product range deliver continuity of supply and access to compatible metrology accessories. The combination of tight tolerance, engineered material properties and workshop‑ready finish offers a pragmatic balance of precision and durability, making the pin suitable as a small yet crucial component of a robust inspection strategy. Secure consistent end‑dimension control with Metav IndustryLine gauge pins — contact Metav Werkzeuge for tailored supply and technical guidance on integration at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.216 GTIN/EAN: 4061905055690 Label: Prüfstift, einzeln, 2,16 mm, ±0.001 mm, length 50 mm Manufacturer: Metav IndustryLine Numerical data Diameter: 2.16 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Execution: Workshop version Single unit delivery Category: Gauge pin / Test pin FAQ What tolerance does this gauge pin offer? The M323.216 gauge pin is specified with a tolerance of ±0.001 mm, providing a 1 µm allowance suitable for high‑precision end‑dimension verification. Which material is used for the pin? The pin is made from special steel, selected for hardness and dimensional stability appropriate to workshop inspection tasks. Is the pin suitable for checking small bores and locating holes? Yes, with a diameter of 2.16 mm and a 50 mm length, the pin serves as a precise reference for small bores, locating holes and related end‑dimension checks. Can the gauge pin be used in fixtures and pin holders? The compact, single‑piece design allows integration into bench fixtures and pin holders for comparative or assembly verification tasks. Who supplies this product and where can more information be obtained? Metav IndustryLine supplies the M323.216 precision gauge pin; further technical details and purchasing information are available through Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.17mm Gauge Pin Single ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of micron-level accuracy, robust workshop construction and compact length for reproducible end‑measure checks; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. M323.217 gauge pin — 2.17 mm diameter, ±0.001 mm accuracy by Metav IndustryLine A precision M323.217 gauge pin designed for fine end‑measure verification and dimensional checks in workshop environments. Precision diameter 2.17 mm ±0.001 mm Length 50 mm for deep or recessed checks Workshop‑grade special steel construction Supplied in protective transport case Micron-level accuracy for critical dimensional checks The core benefit of this measuring pin is its ±0.001 mm tolerance, equivalent to 1 µm, which supports high‑precision verification tasks where repeatability matters. Such accuracy is suitable for end‑measure inspections, plug‑gauge comparisons or tactile checks on small bores and mating parts. The tight tolerance reduces uncertainty in pass/fail decisions and shortens inspection cycles, delivering measurable gains in quality assurance procedures. Compact form and durable workshop design for everyday use With a nominal diameter of 2.17 mm and a length of 50 mm, the pin reaches into recessed features while remaining easy to handle. The special steel construction provides wear resistance in repetitive measurement routines and keeps the contact geometry stable over many cycles. Supplied in a protective transport case, the tool remains protected during storage and transit, preserving the calibrated condition and minimising downtime due to damage. Integrates into inspection routines and fixture setups This single gauge pin is ideal for quick reference checks, fixture setting and comparative measurement tasks in metalworking and precision assembly. Its compact mass supports fast manual handling and repeat measurements with minimal operator fatigue. Traceability is supported through the clear product identification and packaging, enabling straightforward inventory control and replacement planning in serial inspection workflows. For precise end‑measure control choose the Metav IndustryLine M323.217 gauge pin and contact Metav Werkzeuge for personalised technical guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.217 GTIN: 4061905055706 Label: Prüfstift, einzeln, 2,17mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.17 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg Special features Material: Special steel Workshop version Supplied in protective transport case Category: Messstifte FAQ What level of accuracy does the pin provide? The M323.217 gauge pin offers an accuracy of ±0.001 mm, corresponding to 1 µm, suitable for high‑precision dimensional checks. Which materials is the pin suitable for inspecting? The pin is a measuring artefact for dimensional control and is used to check bores and mating parts produced from a wide range of workshop materials. How is the gauge pin delivered? The M323.217 is supplied in a protective transport case to prevent damage during storage and transport. Can the pin be used for embedded or recessed measurements? Yes, the 50 mm length allows checking of recessed features and bores that require slightly deeper reach. Is this item intended for continuous workshop use? The workshop‑grade construction and special steel material make this pin well suited to routine inspection tasks in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.18mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of sub‑micrometre repeatability, robust workshop design and convenient transport packaging for reliable end‑dimension checks. The precise ±0.001 mm tolerance together with a 2.18 mm diameter and a 50 mm length suits compact gauging tasks and repeatable measurements. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test Pin M323.218 — single precision test pin, Ø 2.18 mm, ±0.001 mm (Metav IndustryLine) The Test Pin M323.218 is a single, workshop‑grade precision pin intended for end‑dimension verification and compact gauge assemblies in production and inspection environments. Diameter 2.18 mm, tolerance ±0.001 mm Length 50 mm workshop version Made from special steel Supplied in protective case Precision that supports reproducible end‑dimension checks The core advantage of this instrument is its measuring accuracy of ±0.001 mm, which provides a reliable reference for tight tolerance work. The ground 2.18 mm diameter establishes a clear nominal dimension while the 50 mm length offers sufficient engagement for many plug, pin and end‑mass applications. Because the component is machined from special steel, dimensional stability under normal workshop conditions is improved, reducing drift between checks. This level of precision makes the item suitable as a reference element in comparative gauging setups and in-process spot checks where small deviations must be detected early. Compact design for micro‑scale gauging and micromechanics Classified within the micro measuring range (suitable for tools with a maximum measuring span between 10 and 100 mm), the pin is optimised for confined fixtures, small bores and micromechanical assemblies. The compact geometry lowers the influence of bending and improves handling when fitted into tight gauge housings. For users who assemble or service instruments for watchmaking, small hydraulic components or precision connectors, the combination of minimal footprint and high repeatability supports quicker set‑up times and more consistent results during routine control sequences. Workshop robustness and protected transport packaging This workshop edition has been specified for regular use on the shop floor. The construction from special steel and the workshop finish increase resistance to surface wear while keeping the thread and seating geometry stable. Delivery in a protective case safeguards the reference surface and assists safe storage and transport between inspection stations. The case also simplifies traceability in multi‑station operations, allowing the datum pin to be moved without incidental knocks or contamination that would otherwise compromise measurement reliability. Practical uses and process reliability Typical applications include acting as an end‑mass for plug gauges, a datum pin for fixture alignment and a wear‑reference in routine production sampling. The pin supports efficient pass/fail decisions in go/no‑go workflows and can be integrated into gauge blocks or small adaptors for comparative checks. Metav IndustryLine’s position as a distributor with an on‑site quality filter for the European market adds an additional layer of assurance: the component is offered within a curated selection intended for industrial users who demand reproducibility and straightforward integration into existing quality control processes. Contact Metav Werkzeuge today to specify the Metav IndustryLine test pin for precision end‑dimension checks and to confirm packaging and calibration options tailored to workshop requirements Technical Data SKU: M323.218 GTIN: 4061905055713 Manufacturer: Metav IndustryLine Material: Special steel Length: 50 mm Diameter: 2.18 mm Tolerance: ±0.001 mm Weight: 0.004 kg Facts Length: 50 mm Diameter: 2.18 mm Accuracy: ±0.001 mm Weight: 0.004 kg Special features Workshop version Supplied in protective case for transport Intended for end‑dimension checks and gauge use Ground nominal diameter for repeatable seating FAQ What is the nominal diameter and tolerance of the pin? The pin has a nominal diameter of 2.18 mm with a tolerance of ±0.001 mm, making it suitable for tight tolerance reference tasks. Is the pin supplied ready for storage and transport? Yes, the pin is supplied in a protective case that protects the measuring surface during transport between inspection stations. Which materials is the pin made from? The component is manufactured from special steel chosen for dimensional stability and workshop durability. Can this pin be used as an end mass in plug gauges? The design and length make it suitable for use as an end‑mass or datum pin in compact plug gauges and fixture applications. Who supplies and distributes this test pin? The pin is part of the Metav IndustryLine range and is offered through Metav Werkzeuge with European distribution and quality control procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.19mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm accuracy combined with a 2.19 mm diameter and a 50 mm length for consistent end-measure verification; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.219 — single gauge pin, 2.19 mm diameter, high-precision The M323.219 is a compact gauge pin designed for precise end-measure and limit checks in workshop environments, combining a small footprint with industrial repeatability. High precision ±0.001 mm 2.19 mm diameter for end-measure checks 50 mm length, workshop-ready Special steel construction, protective case included Consistent precision for end-measure verification The gauge pin delivers ±0.001 mm tolerance, equivalent to 1 µm, which supports highly repeatable verification of end measures and small bores. Such accuracy is typically sought where dimensional limits are stringent and a clear go/no-go decision is required. The narrow 2.19 mm diameter makes the pin suited for checking finished bores, seating dimensions and component ends with minimal disturbance to surrounding geometry. The specification allows straightforward integration into quality-control routines where measurable, objective results are needed. Durable, shop-ready design for everyday use Built in a workshop version, the pin is made from special steel chosen for wear resistance and dimensional stability under regular handling. Its 50 mm length provides enough engagement for many end-measure checks while remaining compact for bench or fixture use. The robust material choice reduces fretting and surface wear over time, maintaining the stated tolerance longer than untreated options. Supplied in a protective transport case, the pin arrives ready for safe storage and immediate use on the shop floor. Practical handling, traceability and documentation The single-pin format is lightweight (approx. 0.004 kg), which aids rapid manual inspections and minimises operator fatigue during repeated checks. Clear identification by SKU M323.219 and GTIN 4061905055720 supports traceability in inspection logs and inventory systems. For workshops that prioritise process reliability, the combination of compact size, traceable labelling and robust packaging reduces non-productive time and simplifies stock management. Typical applications and compatibility This pin is intended for precision end-measure checks and small-bore verification in mechanical workshops, toolrooms and quality-control benches. The construction suits routine inspection tasks where simple, rapid verification of final dimensions is required, and where a compact gauge is preferable to larger measuring systems. Its specifications align with common metrology workflows, enabling integration into inspection jigs or comparator setups that demand repeatable point contacts and clear tolerance decisions. Contact Metav Werkzeuge for a consultation on integrating the M323.219 gauge pin into inspection processes or to request application guidance from our measurement specialists. Technical data Article number: M323.219 GTIN: 4061905055720 Label: Prüfstift, einzeln, 2,19mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Category: Messstifte Numbers / Core technical data Diameter: 2.19 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.004 kg Special features / Versions Workshop version Material: Special steel Delivered in protective case (plastic or wooden) Story trigger: end-measure checks FAQ What tolerance does the M323.219 provide? The M323.219 gauge pin is specified at ±0.001 mm, suitable for micrometre-level end-measure verification. Which material is the pin made from? The pin is manufactured from special steel, selected for stability and wear resistance in routine inspection use. Is the pin supplied ready for storage and transport? Yes, the gauge pin is delivered in a protective transport case to preserve the measuring surface and ensure safe handling. Can this pin be used for checking small bores and seating dimensions? The 2.19 mm diameter and precise tolerance make this pin ideal for small-bore checks, seating verification and end-measure inspections in workshop environments. How is the product identified for inventory and traceability? Identification is provided via SKU M323.219 and GTIN 4061905055720 to support traceable inspection records and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.21mm Gauge Pin, ±0.001mm, Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the workshop-grade gauge pin with ±0.001 mm tolerance and a compact 50 mm length for reliable end measurements; combine exceptional accuracy, rugged special-steel construction and straightforward handling to reduce inspection time and rework. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.221 – workshop-grade gauge pin, Ø 2.21 mm, ±0.001 mm A gauge pin M323.221 designed for precise end measurements and go/no-go checking in workshop quality control and inspection tasks. Workshop-grade tolerance ±0.001 mm Diameter 2.21 mm for precision fits Hardened special steel construction 50 mm overall length for depth access Consistent accuracy for production control Built for tasks where every micrometre matters, this gauge pin delivers a tolerance of ±0.001 mm, which translates into dependable repeatability during frequent checks. That level of precision supports quick acceptance or rejection of mating bores and alignment features, reducing downstream rework and scrap. The stated accuracy is a measurable quality parameter that helps maintain process stability and supports traceable inspection routines. Robust design that suits everyday workshop use The shaft is manufactured from special steel, providing a balance of hardness and wear resistance appropriate for shop-floor handling. The 50 mm overall length gives enough reach for many internal depth checks while remaining easy to manoeuvre. A compact, lightweight design means the gauge pin can be used continuously without fatigue, and its workshop specification ensures it withstands regular use in assembly, fixture set-up and incoming inspection operations. Practical integration into inspection workflows As a single precision gauge pin, it is suitable for end measurements, plug checking and fixture calibration where close fits must be verified. The small diameter of 2.21 mm is ideal for fine bores and precision components commonly found in tooling, miniature assemblies and calibration tasks. Combined with Metav’s quality assurance, the tool supports a consistent measurement chain and helps create reliable documentation for quality records and audits. Contact Metav Werkzeuge for tailored advice on selecting precision gauge pins or to discuss suitable inspection routines — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: M323.221 GTIN: 4061905056468 Manufacturer: Metav IndustryLine Facts Diameter: 2.21 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg Special features Material: Special steel Workshop version Single gauge pin delivery FAQ What accuracy does this gauge pin offer? The gauge pin provides an accuracy of ±0.001 mm, making the M323.221 suitable for high-precision end measurements and repeatable plug checks. Which materials is the pin made from? The shaft is made from special steel, chosen for its hardness and wear resistance appropriate to regular workshop inspection use. For which applications is this gauge pin intended? Typical uses include end measurements, plug checking, fixture verification and inspections of small bores in tooling and miniature assemblies. Is the length suited to deep bores? With a 50 mm overall length, the gauge pin offers sufficient reach for many depth checks while remaining easy to handle during repetitive inspections. How does this gauge pin support quality documentation? The defined tolerance and repeatability of the M323.221 enable reliable pass/fail decisions and support traceable inspection records for quality control and audits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.22mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑ready inspection tool that combines ±0.001 mm tolerance and a 2.22 mm controlled diameter with a 50 mm overall length for reliable end‑dimension checks; order directly via Metav Werkzeuge or ask the Metav consultants for application advice. M323.222 gauge pin — Gauge pin, 2.22 mm diameter, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.222 is a single precision gauge pin designed for end‑dimension verification and go/no‑go checks in workshop and production environments Precision tolerance ±0.001 mm Diameter 2.22 mm, ground to size 50 mm overall length for bore checks Workshop version, robust construction Precision that reduces rework and speeds inspection The pin delivers a tight ±0.001 mm tolerance on a nominal 2.22 mm diameter, enabling reproducible go/no‑go and limit tests that reduce measurement uncertainty and scrap rates. Ground to size from special steel, the hardened and finished shaft offers stable contact geometry so repeatability improves throughput in small‑bore inspection routines. This combination of accuracy and robustness supports faster in‑process decisions and fewer downstream corrections. Practical design for repeatable fit‑up and handling With a 50 mm overall length and a controlled shaft diameter, the tool is optimised for verifying end dimensions, plug fits and alignment in jigs, fixtures and mating parts. The workshop version balances wear resistance with everyday handling: its compact mass ensures quick placement into bores and minimal deflection, while the surface finish maintains a consistent fit. The lightweight construction also assists rapid manual checks without special fixtures, saving cycle time on repetitive inspections. Integrates cleanly into inspection workflows The gauge pin is suitable for routine production control and finishing inspections where end‑dimension conformity is critical. Marking and traceable identification simplify log keeping and batch control, while the compact size supports storage alongside standard hand tools. When combined with systematic sampling, the pin contributes to a measurable improvement in first‑pass yield and a consistent quality record across batches. Contact Metav Werkzeuge for tailored advice on using the Metav IndustryLine M323.222 gauge pin in specific inspection processes and to confirm availability from Emmerich stock Technical data Article number: M323.222 GTIN: 4061905056475 Manufacturer: Metav IndustryLine Facts Diameter: 2.22 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg Material designation: Special steel Special features Workshop execution Ground to size shaft Intended for end‑dimension and bore checks Single piece delivery FAQ What tolerance is specified for this gauge pin? The M323.222 gauge pin is specified with a tolerance of ±0.001 mm on the 2.22 mm diameter. What applications is the pin intended for? The pin is intended for end‑dimension verification, go/no‑go checks in bores, fit‑up and alignment tasks in workshop and production inspection. What material is the pin made from? This gauge pin is manufactured from special steel with a ground finish for wear resistance and consistent contact geometry. Is the tool suitable for production spot checks? Although labelled as a workshop version, the M323.222 offers precision suitable for regular production spot checks and inspection tasks requiring tight diametral control. What are the physical dimensions and mass of the pin? Nominal diameter 2.22 mm, overall length 50 mm, weight approximately 0.004 kg. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.23mm Test Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial durability, sub‑micrometre repeatability and compact handling for reliable end‑dimension checks. Order the pin directly via Metav Werkzeuge or consult the team for application advice. Test pin M323.223 — single measuring pin, 2.23 mm, ±0.001 mm, 50 mm length The test pin M323.223 is a workshop‑grade measuring pin designed for precise end‑dimension and fit verification in production and inspection environments. Workshop edition for industrial use Diameter 2.23 mm for tight fit checks Accuracy ±0.001 mm for high precision 50 mm hardened shaft for stable handling Consistent, traceable precision for end‑dimension checks Manufactured for repeatable measurement, this single measuring pin delivers an accuracy of ±0.001 mm, making it suitable where narrow tolerances determine part acceptance. The 2.23 mm diameter and 50 mm effective length are optimised for end‑mass and small‑bore verification tasks; the compact geometry reduces bending and measurement noise. By relying on a finely ground shaft and controlled production, the pin supports consistent contact conditions that reduce operator influence and improve batch‑to‑batch comparability — a clear rational advantage for shop floor and laboratory routines. Durable workshop design with machinist‑grade material The pin is produced from special steel, selected for wear resistance and dimensional stability under repeated contact. The workshop edition construction emphasises robustness: a hardened shaft and precise ground ends maintain form over many cycles, and the single, standalone format simplifies storage and interchangeability in common gauge sets. These material choices lower the frequency of replacement and contribute to predictable measurement results, which in turn supports efficient quality workflows and reduces unplanned downtime. Practical integration into quality control and inspection flows As a measuring tool for end‑dimensions and fit checks, the pin suits incoming inspection, final acceptance, and in‑process control. The compact form factor allows quick handling in fixtures, bores and gauges; the M323.223 designation eases ordering and inventory. For applications that demand documented traceability, the pin can be logged into inspection plans and paired with established procedures to validate assembly clearances or mating fits. Contact channels are available for technical clarification to ensure the pin meets the required inspection context. Speak to Metav Werkzeuge for tailored advice and procurement — the team can confirm suitability for specific inspection tasks and support efficient integration into existing control plans Technical data Article number: M323.223 GTIN: 4061905056482 Material: Special steel Weight: 0.004 kg Facts Diameter: 2.23 mm Length: 50 mm Tolerance / accuracy: ±0.001 mm Category: Measuring pin (single) Special features Workshop edition (Werkstatt‑Ausführung) Ground ends for accurate contact Single pin delivery for flexible use FAQ What is the primary application for this measuring pin? The measuring pin M323.223 is intended for precise end‑dimension and fit verification in production inspection and quality control. Does the pin require special handling to maintain accuracy? Regular cleanliness and correct seating in fixtures preserve the ±0.001 mm accuracy of the test pin; avoid impacting the ground ends and store in a protective compartment when not in use. Is the material specified for wear resistance? Yes, the pin is made from special steel, chosen to provide durable contact surfaces and maintain dimensional stability under repeated use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.24mm Gauge Pin Length 50mm ±0.001mm Workshop Finish, Special Steel - Metav IndustryLine
Take advantage of the combination of extreme dimensional accuracy and a compact, robust design to secure reliable end‑dimension checks and stable routine inspection work. The precise ±0.001 mm tolerance together with a 50 mm length ensures reproducible results in production control; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Precision Gauge Pin M323.224 — 2.24 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Precision Gauge Pin M323.224 is a single test pin designed for high‑precision end‑dimension verification and small‑bore inspection in workshop and production environments. Precision tolerance ±0.001 mm Diameter 2.24 mm for fine checks Length 50 mm suitable for deep fittings Special steel workshop version Confidence from measurable accuracy With a tolerance of ±0.001 mm, this gauge pin provides a level of accuracy that supports critical fit and clearance checks on small components. The extremely tight tolerance reduces uncertainty in acceptance decisions and helps to avoid downstream rework. Interpreting the figure: a deviation of one thousandth of a millimetre corresponds to micrometric control of bore and shaft fits, which is pivotal for final inspection and functional testing. Robust, compact design for routine inspection Constructed from special steel, the test pin combines surface hardness with dimensional stability for repetitive use in a workshop setting. The 50 mm length gives sufficient reach for deeper holes while maintaining stiffness to minimise bending during handling. The compact mass contributes to quick handling and fast cycle checks, making the component suitable for both bench inspection and integration into simple gauging fixtures. Practical integration into quality processes The pin is intended for end‑dimension (end size) verification and routine plug checks where consistent pass/fail assessment is required. The small diameter and fine tolerance make it ideal for control tasks in component manufacturing and assembly inspection. Identification is straightforward via article number and GTIN, facilitating procurement and traceability in quality documentation; the item is supplied as a single test pin ready for immediate use in inspection workflows. Contact Metav Werkzeuge today to discuss how the M323.224 precision gauge pin can be matched to existing inspection routines or to arrange supply through our Emmerich distribution centre. Technical data Article number: M323.224 GTIN: 4061905056499 Label: Prüfstift, einzeln, 2,24mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 2.24 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg EClass: 21170231 Special features Material: Special steel Workshop execution Single test pin for end‑dimension checks Compact, high‑precision design FAQ What level of precision does this gauge pin provide? The M323.224 gauge pin is specified to ±0.001 mm, providing micrometric accuracy suitable for tight fit and final inspection tasks. Is the material suitable for regular workshop use? Yes, the pin is made from special steel, selected to offer durability and dimensional stability for frequent handling and routine checks in a workshop environment. Can the pin be used for deeper bore checks? With a 50 mm length, the pin is appropriate for many deeper bore inspections while retaining sufficient stiffness for reproducible results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.25mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm accuracy and the compact 50 mm length for reliable end‑dimension checks; the robust special‑steel shaft and protective transport box keep measurement ready in the workshop. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.225 — 2.25 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.225 is a workshop-grade precision pin for end‑dimension and go/no‑go gauging in industrial metrology. Workshop-grade precision ±0.001 mm Diameter 2.25 mm for end‑dimension checks 50 mm hardened special‑steel shaft Supplied in transport box for protection High accuracy that speeds up inspection The compact gauge pin delivers ±0.001 mm tolerance, reducing measurement uncertainty in short‑run and serial checks. That level of precision ensures repeatable go/no‑go assessments and accurate verification of end dimensions, which shortens inspection cycles and lowers the risk of downstream rejects. The hardened special‑steel construction preserves geometry under repeated contact, so calibration intervals remain practical and downtimes are minimised. Compact design for workshop robustness At 50 mm overall length and 2.25 mm diameter, the pin is optimised for confined measurement points and assembly control tasks. The small mass and sturdy shaft provide good handling and minimal deflection during use, enabling fast placement in jigs or bore checks. The workshop specification means the component resists typical shopfloor wear while remaining easy to store and deploy for spot checks or batch sampling. Practical traceability and handling Supplied ready for use in a protective transport box, the pin is convenient to move between benches without risk of damage. The clear SKU and GTIN support inventory control and traceability in quality workflows, while the simple geometry makes the pin compatible with standard holders and checking fixtures. For routine inspection needs, this solution balances operability with the metrological performance required in production environments. Contact Metav Werkzeuge for application consultation or to order the Metav IndustryLine M323.225 gauge pin and ensure fit with existing inspection processes. Technical data Article number: M323.225 GTIN: 4061905056505 Manufacturer: Metav IndustryLine Facts Diameter: 2.25 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: special‑steel Workshop version Supplied in transport box Intended for end‑dimension gauging (end mass) FAQ What accuracy can be expected from this pin? The M323.225 gauge pin from Metav IndustryLine is manufactured to ±0.001 mm tolerance, suitable for precise end‑dimension checks and repeatable go/no‑go measurements. Is the pin suitable for use in production fixtures? Yes, the hardened special‑steel shaft and compact 50 mm length make the pin appropriate for integration into jigs, holders and quick‑check fixtures on the shopfloor. How is the product delivered and protected? The gauge pin is supplied in a protective transport box to prevent handling damage and simplify storage between inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.26mm Gauge Pin Length 50mm ±0.001 mm, Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade inspection pin that combines micrometre‑level precision and robust construction for reliable end‑dimension checks; its 2.26 mm diameter with ±0.001 mm accuracy and 50 mm overall length make it a practical choice for repetitive gauge and reference measurements. Order the M323.226 test pin directly via Metav Werkzeuge or ask our consultants for application advice. M323.226 Test Pin — 2.26 mm, ±0.001 mm — Workshop version by Metav IndustryLine The M323.226 test pin is a single, workshop‑grade inspection pin designed for precision end‑dimension checks and gauge use in small‑component inspection. Workshop‑grade precision Diameter 2.26 mm, tolerance ±0.001 mm Robust special‑steel construction 50 mm overall length Faster, repeatable checks with micrometre precision A compact inspection tool with a declared accuracy of ±0.001 mm, the pin is tailored for tasks that demand tight end‑dimension control. The combination of a slim 2.26 mm shaft and short overall length reduces lever effects and improves repeatability during insertion into bore gauges or fixture seats. Classified in the Mikro measurement group (very compact instruments for fine mechanical work), this design shortens inspection loops and reduces rework by delivering unambiguous results at the production bench. Built for workshop durability and consistent handling Constructed from special steel, the pin withstands routine handling and resists surface damage that could affect reference measurements. The 50 mm length provides a useful engagement depth for many gauge housings while keeping the tool easy to manoeuvre with standard workshop tooling. The workshop version specification balances wear resistance with the dimensional stability needed for frequent use, so measurement cycles remain efficient without sacrificing service life. Practical integration into quality control processes The single‑piece design makes this inspection pin straightforward to incorporate into gauge stacks, plug gauges or fixture checks for end‑dimension verification. Its light weight and compact form factor aid rapid alignment and reduce cycle time for repetitive measurements. When documented traceability is required, Metav Werkzeuge offers technical advice and supply reliability from Emmerich to support continuous inspection routines and procurement planning. Choose Metav IndustryLine's workshop‑grade M323.226 test pin for consistent end‑dimension control — contact Metav Werkzeuge for tailored technical advice and secure supply from Emmerich. Technical Data Article number: M323.226 GTIN: 4061905056512 Category: Messstifte Brand: Metav IndustryLine Facts Diameter: 2.26 mm Length: 50 mm Accuracy / tolerance: ±0.001 mm Weight: 0.004 kg Special features Workshop version Material: special steel Single test pin for inspection and gauge use Measurement classification: Mikro (max. 10–100 mm) FAQ What declared accuracy does the M323.226 offer? The M323.226 test pin from Metav IndustryLine is specified with an accuracy of ±0.001 mm for precise end‑dimension verification. Is the M323.226 supplied with a calibration certificate? The M323.226 is supplied as a workshop test pin; it is not delivered with an ISO 17025 calibration certificate unless explicitly stated on a specific article label. What material is the inspection pin made from? This inspection pin is manufactured from special steel, selected for dimensional stability and resistance to wear in routine workshop use. Which inspection tasks suit this pin best? The M323.226 is intended for end‑dimension checks, plug‑gauge support and reference measurements in small‑component inspection and fixture validation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.27mm Gauge Pin Length 50mm ±0.001mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of high reproducibility, micrometre-level accuracy and a compact 50 mm length to perform repeatable end‑measure and hole gauging with minimal setup time. Order the gauge pin directly via Metav Werkzeuge or consult the team for application matching and calibration advice. Gauge pin M323.227 – 2.27 mm, tolerance ±0.001 mm (Metav IndustryLine) A Gauge pin M323.227 designed for precise end‑measure checks and hole gauging in workshop inspection and fixture set‑ups Diameter 2.27 mm with ±0.001 mm tolerance Length 50 mm for deep insertion checks Special steel, workshop execution Consistent micrometre accuracy for critical checks The principal advantage of this precision pin is its ±0.001 mm specification, which provides clearly defined limits for go/no‑go assessment and reference measurements. Such a tolerance reduces uncertainty in serial inspection and tool setup, allowing measurement routines to be standardised across shifts. The small diameter of 2.27 mm and compact 50 mm length make the item particularly useful where access is restricted or when multiple pins are used to establish datum lines; the design supports repeatable contact conditions and predictable elastic deflection during insertion. Durable construction for routine workshop use Manufactured in special steel and delivered in a workshop configuration, the pin is built for frequent handling and insertion cycles. The material choice balances hardness and surface finish to preserve the cylindrical form and minimise wear on measurement faces, which directly supports long‑term repeatability. At about 0.004 kg, the component is easy to position and integrates well with handheld probes, bench fixtures or automated pick‑and‑place routines without adding significant inertia to assemblies. Fits into common inspection and tooling workflows As a compact test pin, this component is suited to a range of tasks: end‑measure verification, hole alignment checks, locating and fixture validation. Traceable identification via GTIN and the SKU ensures straightforward inventory and process documentation when the pin is included in quality plans or inspection reports. The form factor also allows straightforward pairing with comparator setups and indexing plates, helping to speed up changeovers and reduce machine downtime through faster verification steps. Select the Metav IndustryLine M323.227 when accuracy and workshop durability are decisive — contact Metav Werkzeuge for specification matching and procurement at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: M323.227 GTIN: 4061905056529 Manufacturer: Metav IndustryLine Facts Diameter: 2.27 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Material: Special steel Workshop execution ECLASS: 21170231 FAQ What level of accuracy does this pin provide? The pin offers a tolerance of ±0.001 mm, making the M323.227 suitable for micrometre‑level checks and repeatable reference measurements. What material is used for the test pin and why? The test pin is made from special steel to provide a durable contact surface and long service life under regular insertion and inspection cycles. Which applications are typical for this gauge pin? Typical uses include end‑measure verification, hole gauging, fixture alignment and datum establishment in workshop and inspection environments. How is the pin identified for inventory and documentation? The product is identifiable by its article number M323.227 and GTIN 4061905056529 for traceability in quality systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.28mm Gauge Pin Length 50mm ±0.001mm Workshop Finish, Supplied in Case - Metav IndustryLine
Take advantage of the combination of high-precision measurement, robust workshop construction and compact handling for reliable end‑dimension checks. The tight ±0.001 mm tolerance and special steel construction support consistent inspection results; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.228 — precision 2.28 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) A Gauge pin M323.228 designed for precise end‑measurements and assembly checks in workshop and inspection environments Precision tolerance ±0.001 mm Diameter 2.28 mm nominal Length 50 mm for end measurements Workshop version in special steel Repeatable accuracy for end‑measurement tasks The small diameter and fine tolerance deliver consistent measurement certainty where fit and clearance matter. With a nominal 2.28 mm diameter and a manufacturing tolerance of ±0.001 mm, this test pin provides the repeatability required for go/no‑go checks, pin gauges and reference measurements in toolrooms and production control. The compact form factor reduces positional error during placement, meaning fewer reworked parts and more dependable quality control outcomes. Robust workshop construction with compact handling Made from special steel, the test pin is built for regular use in workshop conditions and resists wear in contact applications. The 50 mm length gives enough engagement for reliable end‑face checks without adding unnecessary overhang, and the low mass supports swift, single‑hand operation in assembly or inspection routines. The workshop specification ensures practical handling while maintaining the surface integrity needed for accurate end measurements. Fits into standard inspection workflows and traceability systems Designed as a single, purpose‑made inspection pin, this item integrates easily into measurement jigs, height gauges and checking fixtures. The compact design promotes rapid exchangeability in batch inspections and reduces set‑up time. Clear identification via SKU and GTIN supports traceability in quality documentation and stock management, helping to uphold process consistency and audit readiness while minimising production interruptions. For immediate procurement or technical advice on application and traceability, contact Metav Werkzeuge – our specialists can advise on using the M323.228 gauge pin in inspection sequences and inventory systems Technical data Article number: M323.228 GTIN: 4061905057175 Manufacturer: Metav IndustryLine Facts Diameter: 2.28 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.004 kg Special features Workshop version Material: Special steel Single test pin for end measurements Category: Messstifte FAQ What tolerance does this gauge pin offer? The gauge pin M323.228 is manufactured to a tolerance of ±0.001 mm, ensuring high repeatability for end‑measurement tasks. Which material is used for the test pin? This workshop version is made from special steel, chosen for wear resistance and dimensional stability under routine inspection use. Is the length suitable for fixture checks? The 50 mm length provides sufficient engagement for end‑face inspections and is compatible with common checking fixtures and jigs. Can the gauge pin be used for serial inspection? Yes; the combination of tight tolerance and robust material makes the M323.228 suitable for batch control, go/no‑go checks and assembly verification. How is the item identified for stock and traceability? Identification is possible via SKU M323.228 and GTIN 4061905057175 to support stock management and audit trails. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2.29mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of workshop‑grade robustness and 1 µm (±0.001 mm) measurement certainty in a compact 50 mm length; the combination of special steel construction and delivery in a transport case supports reliable in‑process checks and safe storage. Order the pin gauge directly via Metav Werkzeuge or consult our specialists for application advice. Pin Gauge M323.229 — 2.29 mm, ±0.001 mm, 50 mm (Metav IndustryLine) A Pin Gauge M323.229 designed for precise end‑dimension verification and repeatable inspection work in workshop and quality‑control environments. Workshop design for robust daily use Diameter 2.29 mm with ±0.001 mm accuracy Length 50 mm, compact inspection pin Supplied in transport case for safe storage Faster, reliable measurements with micrometric accuracy This compact inspection pin delivers a 2.29 mm nominal diameter with a guaranteed ±0.001 mm deviation, corresponding to a 1 µm tolerance band. Such accuracy shortens the decision loop during routine checks, because pass/fail conclusions can be reached without additional adjustment steps. The pin is especially suited for end‑dimension control and fits directly into gauges, fixtures or measuring jigs, making it a practical tool for fast inspection tasks. The use of special steel ensures dimensional stability under typical workshop conditions and improves long‑term repeatability of results. Built for the workshop: robustness and handling benefits Manufactured in a workshop execution, the probe combines a practical length of 50 mm with a low mass (approx. 0.004 kg) to simplify handling and minimise operator fatigue during repetitive checks. The compact form factor reduces the risk of bending and allows insertion into confined fixtures and bores. Supplied in a transport case, the pin is protected during storage and transit, reducing injury risk and preserving the calibrated surface. The robust finish reduces susceptibility to light knocks and abrasion, maintaining the measurement surface and therefore the integrity of inspection routines. Practical application and integration into quality workflows Intended for end‑dimension and go/no‑go checks, the inspection pin is an efficient reference element in assembly lines, inspection benches and toolrooms. Its narrow diameter makes it suitable for small‑bore verification and finishing checks where traceable, repeatable contact points are required. The product supports standardised measurement procedures and can be incorporated into fixtures to reduce setup time during series inspection. As a single‑piece gauge, it simplifies stockkeeping while providing a precise reference for comparative measurements. Choose the Metav IndustryLine M323.229 for dependable, workshop‑ready precision; contact Metav Werkzeuge in Emmerich for ordering or technical consultation at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: M323.229 GTIN: 4061905057557 Manufacturer: Metav IndustryLine Facts Diameter: 2.29 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.004 kg Special features Material: special steel Workshop execution Supplied in transport case Category: Pin gauges (Messstifte) FAQ What is the tolerance of this inspection pin? The Metav IndustryLine pin gauge M323.229 is specified with a tolerance of ±0.001 mm (1 µm). Is the pin suitable for small‑bore end‑dimension checks? Yes, the 2.29 mm diameter and compact 50 mm length make this inspection pin appropriate for small‑bore and end‑dimension measurements. How is the gauge delivered and protected? Delivery of the M323.229 includes a transport case to protect the pin during storage and shipment. Which material is used for the pin? The inspection pin is made from special steel, chosen for dimensional stability and workshop durability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com