Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
13.29mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Thanks to its combination of high repeatability and robust workshop construction, this gauge pin delivers reliable end-measurement results with minimal setup time. Benefit from ±0.002 mm accuracy and a compact 50 mm length for stable handling; order directly via Metav Werkzeuge or consult our specialists for integration into inspection routines. Gauge pin, single — 13.29 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single, 13.29 mm, length 50 mm is a precision measurement pin designed for end-dimension checks and routine inspection tasks in workshop and production environments. Workshop execution, robust construction Diameter 13.29 mm for precise end measurements Length 50 mm for stable handling Accuracy ±0.002 mm for repeatable results Repeatable end measurements with micron-level precision The precision pin offers an accuracy of ±0.002 mm (±2 µm), providing a measurable advantage where repeatability matters. Manufactured from special steel, the pin resists routine wear and maintains contact geometry during serial checks. This level of precision reduces measurement scatter in incoming inspection and process control, translating into fewer rejects and more reliable pass/fail decisions on the shop floor. Built for workshop use and straightforward handling A compact 50 mm length pairs with the 13.29 mm diameter to give a stiff, easy-to-handle gauge that stays stable during placement. The workshop execution balances toughness and dimensional stability so that the pin can be used repeatedly in test benches, fixtures or manual go/no-go checks without complex fixturing. Its modest weight and straightforward geometry simplify handling, which speeds up inspection cycles and reduces operator fatigue. Integration into inspection workflows and traceable documentation This single gauge pin is suited to end-measurement tasks in inspection benches, gauges and comparative setups. As a standardised measurement element, it can be incorporated into modular test fixtures or used as a reference pin for quick checks during setup. The compact dimensions and industry-standard construction allow easy interchange with other precision plugs in inspection sets, supporting consistent quality assurance across production steps. Contact Metav Werkzeuge today for product matching and ordering of the Metav IndustryLine gauge pin — Metav’s specialists in Emmerich will advise on application fit and supply logistics via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.D29 GTIN: 4061905067907 Brand: Metav IndustryLine Facts Diameter: 13.29 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Execution: Workshop version Application: End measurements ECLASS: 21170231 FAQ What tolerance does the gauge pin provide? The gauge pin has an accuracy of ±0.002 mm, suitable for repeatable end-dimension checks in routine inspection. Which material is used for the pin? The pin is manufactured from special steel, chosen for dimensional stability and wear resistance in workshop applications. Is the pin suitable for bench and fixture use? Yes; the workshop execution and the 50 mm length make this pin appropriate for test benches, fixtures and manual comparative checks. What are the exact dimensions and identifiers for ordering? Diameter 13.29 mm, length 50 mm, SKU M323.D29, GTIN 4061905067907; brand Metav IndustryLine. How does the pin support process control? As a standardised measurement element, the pin provides repeatable end measurements that reduce scatter in inspections and support consistent quality decisions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.2mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
The combination of 13.2 mm diameter, a 50 mm length and a verified tolerance of ±0.002 mm delivers reliable hole gauging for workshop and production checks; ideal for repeated use in assembly and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. M323.D20 – Single Gauge Pin (13.2 mm Ø, 50 mm length) by Metav IndustryLine The M323.D20 is a single precision gauge pin designed for workshop measurement and hole verification in machining and inspection workflows. Workshop version for robust daily use Diameter 13.2 mm for accurate hole checking Length 50 mm suitable for through and blind holes Special steel construction, precision ground Precision where it matters for production control The gauge pin provides a clear, measurable reference for bore and fit inspection. With a 13.2 mm diameter produced to an allowance of ±0.002 mm, the pin supports tight tolerance checks in serial production and manual inspection stations. The special steel construction is precision ground, reducing surface variations that can skew measurements and ensuring consistent contact with mating bores. This focus on dimensional stability reduces rework and speeds up quality decisions on the shop floor. Robust design for workshop environments Designed as a workshop version, this single gauge pin tolerates everyday handling and repeated seating in jigs and fixtures. At an overall 50 mm length it offers good accessibility for both through and partially blind bores while remaining manageable for single-operator use. The construction balances stiffness and wear resistance, so the pin maintains its geometry through repeated cycles and provides a reproducible reference for pass/fail checks in maintenance, incoming inspection and assembly. Practical benefits and inspection efficiency Using a dedicated gauge pin simplifies go/no-go assessments and streamlines inspection routines: a clearly defined diameter and certified tolerance removes subjective judgement from fit checks. The compact weight and form factor allow quick swapping between gauges in a bench set-up or insertion into holders and mandrels. For traceability and inventory, the item is listed under SKU M323.D20 and GTIN 4061905066276, which helps integrate the pin into existing procurement and quality records. For precise bore verification and dependable workshop performance trust Metav IndustryLine—contact Metav Werkzeuge for procurement and technical guidance at info@metav-werkzeuge.com or by phone; support is available from the Metav team. Technical data Article number: M323.D20 GTIN: 4061905066276 Label: Prüfstift, einzeln, 13,2 mm Länge 50 mm Facts Diameter: 13.2 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: Special steel Precision ground surface SKU: M323.D20 FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, making the M323.D20 suitable for fine inspection tasks that require tight dimensional control. Which materials is the pin suitable for checking? The M323.D20 serves as a dimensional reference for bores regardless of workpiece material; the pin itself is made from special steel to ensure durability and wear resistance during repeated checks. How is the gauge pin identified for inventory and traceability? Identification is supported by SKU M323.D20 and GTIN 4061905066276, which can be recorded in quality systems and procurement lists for traceable handling. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.3 mm Gauge Pin Length 50 mm Workshop Version Plastic Case - Metav IndustryLine
Take advantage of the combination of precision, robust workshop construction and practical traceability for reliable end‑measurement checks; the 13.3 mm diameter and 50 mm length ensure consistent fit control while the delivery in a protective case supports safe transport and storage. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.D30 — single precision test pin, Ø13.3 mm, 50 mm length (Metav IndustryLine workshop version) The gauge pin M323.D30 is a single, workshop‑grade test pin designed for precise end‑measurements and fit verification of bores and components with a 13.3 mm nominal diameter and a 50 mm shank. Workshop‑grade execution Diameter 13.30 mm for tight fits Length 50 mm with robust shank Tolerance ±0.002 mm for precise checks Precision that supports repeatable end‑measurements The pin provides a stable reference for checking seatings, bores and mating fits thanks to its ±0.002 mm specification, which delivers highly repeatable results for routine validation tasks. This level of control reduces uncertainty in pass/fail decisions and shortens inspection cycles, transforming measurement data into reliable evidence for quality documentation. The 13.3 mm diameter is optimised for tight fits where small deviations matter, so operators benefit from reduced rework and clearer acceptance criteria. Built for workshop durability and safe handling Manufactured from special steel and specified as a workshop version, the probe combines surface strength with form stability for frequent handling. The 50 mm shank offers a comfortable gripping length without compromising stiffness, making the pin suitable for bench inspection, fixture checks and slip‑fit controls. Delivery in a protective case ensures the item arrives ready for use and remains protected during transport, preventing nicks that would otherwise affect measurement integrity. Practical use and straightforward operation The design is intentionally simple: a single, precision ground pin that serves as a direct reference in assembly checks, gauge stacks or comparator setups. The compact geometry and robust shank enable quick manual positioning and easier access into deep or recessed bores. Operators unfamiliar with specialist terminology will appreciate that the device performs a single, clear function — accurate end‑measurement — with no additional adjustment required, which speeds up inspection routines and lowers the training threshold. Confidence through specification and distribution Traceability is supported by clear technical data and Metav’s quality infrastructure, which acts as a practical quality filter for the European market. The combination of defined tolerance, resilient construction and controlled delivery reduces the risk of non‑conforming checks entering production. For workshop and maintenance environments where reproducibility matters, this small tool contributes directly to process reliability and the documentation chain required for internal QA. For procurement or technical queries about Metav IndustryLine gauge pins, contact Metav Werkzeuge for personalised advice and ordering—email info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: M323.D30 GTIN: 4061905067914 Brand: Metav IndustryLine Category: Gauge pins Label: Gauge pin, single, Ø13.3 mm, length 50 mm Core measurements Diameter: 13.3 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials and features Material: special steel Workshop version Delivered in protective case FAQ What is the intended use of this gauge pin? The gauge pin M323.D30 is intended for end‑measurement checks, bore verification and fit control where a 13.3 mm reference is required. What tolerance can be expected from the test pin? The test pin is specified with a tolerance of ±0.002 mm, providing repeatable checks for workshop inspection tasks. Is the pin supplied ready to use and protected? Yes, the M323.D30 is delivered in a protective case suitable for transport and safe storage to preserve the measurement surface. Which material is used for the probe? The probe is manufactured from special steel chosen for dimensional stability and resistance to frequent handling. Can this pin be used for precision gauge stacking? The robust shank and precise diameter make the pin suitable for incorporation into gauge stacks and comparative setups in workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.31mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of precise diameter control, workshop-grade robustness and traceable identification for reliable inspection results; order directly via Metav Werkzeuge or consult our specialists for application advice M323.D31 Gauge pin — single gauge pin, 13.31 mm diameter, 50 mm length (Metav IndustryLine) A M323.D31 gauge pin designed for accurate end‑measurements, alignment and inspection tasks in workshop and quality‑control environments Workshop version for robust daily use Diameter 13.31 mm with ±0.002 mm accuracy Compact 50 mm length for tight inspection spaces Single item with clear traceability via SKU and GTIN Precision that reduces rework and speeds inspection A compact inspection pin with a nominal diameter of 13.31 mm, manufactured from special steel, delivers repeatable contact geometry for small bores and gauge fixtures. The tight tolerance of ±0.002 mm provides the confidence needed for go/no‑go checks, bore alignment and plunger‑style verification. By standardising on a precisely ground reference pin, measurement loops become more predictable and setup times fall, which supports improved throughput in repetitive inspection tasks. Built for everyday workshop conditions This workshop‑grade reference pin combines a short, firm profile with low mass (approx. 0.1 kg) and a 50 mm working length, making it easy to handle during rapid checks and tool setting. The robust material choice ensures dimensional stability under typical shop temperatures and handling. Supplied as a single unit, the component integrates seamlessly into jigs and test rigs and serves as a dependable reference in small‑part production, reducing uncertainty at the inspection stage. Traceability and inventory integration for quality systems Identification by SKU M323.D31 and GTIN 4061905067921 supports inventory control and audit trails within quality management systems. The simple, unambiguous specification (diameter, length, material and tolerance) makes the pin straightforward to list in bills of materials and measurement plans. Using clearly referenced master parts such as this pin helps maintain reproducibility across shifts and sites and simplifies procurement within larger supply chains. For secure, repeatable inspection with the M323.D31 gauge pin, contact Metav Werkzeuge for availability and expert advice—Metav Werkzeuge is your partner for precision tools and can be reached at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data SKU: M323.D31 GTIN: 4061905067921 Manufacturer: Metav IndustryLine Facts Diameter: 13.31 mm Length: 50 mm Accuracy/Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Delivery: single gauge pin Designation: Workshop execution eClass: 21170231 Story trigger: end‑measurements FAQ What is the nominal diameter and tolerance of the pin? The nominal diameter is 13.31 mm with a dimensional tolerance of ±0.002 mm for the M323.D31 gauge pin. Which material is used for this gauge pin? The pin is manufactured from special steel, chosen for dimensional stability and workshop suitability. Is the pin supplied as a single item or in a set? This product is supplied as a single gauge pin marked as SKU M323.D31. What applications is this pin suited to? The pin is intended for end‑measurements, bore alignment, fixture setting and routine inspection tasks in workshop and production contexts. How does the M323.D31 support quality systems? Traceability via SKU M323.D31 and GTIN 4061905067921 allows easy integration into inventory lists, measurement plans and audit documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.32mm Go/No-Go Gauge Pin 50mm Workshop Version, Special Steel - Metav IndustryLine
Benefit from the combination of a 13.32 mm diameter, ±0.002 mm accuracy and robust special steel construction for consistent inspection results; the compact 50 mm length supports safe handling in fixtures and gauges. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D32 — single precision test pin, 13.32 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.D32 is a single precision test pin designed for end‑measure checks and workshop inspection tasks where repeatable diameter reference and compact handling are required. Precision diameter 13.32 mm, ±0.002 accuracy Short 50 mm length for secure fixture handling Special steel for long wear resistance Delivered in a protective box for transport Reduce rework with measurable precision A consistent production flow depends on measurable, repeatable checks. The gauge pin provides a 13.32 mm reference diameter with a verified ±0.002 mm deviation, which translates into reliable pass/fail verification at assembly or inspection stations. This level of control reduces rework and scrap by tightening the dimensional gate early in process chains. The calculation of tolerances and the narrow accuracy band support efficient quality decisions and fewer stoppages during serial checks. Robust construction for everyday workshop use Constructed from special steel, the pin resists wear and maintains dimensional integrity under frequent insertion and withdrawal cycles. The workshop‑grade finish and material selection minimise surface damage that can bias measurements over time. As a result, maintenance intervals are extended and replacement costs are reduced — a practical advantage for production environments where tools are used continuously and downtime carries a measurable cost. Compact format that fits tight assemblies With a length of 50 mm, the test pin offers safe handling in confined fixturing and gauge housings without excess overhang. The short form factor improves accessibility to end faces and bores in compact components, while retaining sufficient mass for steady handling. This balance between reach and rigidity benefits measurement technicians who require a stable datum in tight assemblies and in-process inspection jigs. Protected delivery for transport and workshop logistics The article is supplied in a protective box suitable for transport, reducing the risk of accidental knocks or corrosion during storage or transit; the packaging is primarily intended to safeguard the tool rather than for permanent storage. Robust packaging supports reliable logistics and ensures the pin reaches the bench ready for immediate use, preserving the factory calibration and surface condition expected for precision inspection tools. Practical application and integration in inspection routines The gauge pin serves as a straightforward reference for go/no‑go checks, comparator setups and quick end‑measure verification in a wide range of workshop and inspection workflows. Its compact dimensions and tight tolerance make it suitable for routine quality control in metalworking and assembly processes. For operations seeking standardised reference artefacts, this test pin integrates easily into existing gauge sets and fixture designs. Contact Metav Werkzeuge to discuss how the Metav IndustryLine gauge pin M323.D32 with a 13.32 mm diameter and ±0.002 mm accuracy fits into inspection workflows, or to place an order by phone (+49 2822 7131930) or e‑mail (info@metav-werkzeuge.com) Technical data Article number: M323.D32 GTIN: 4061905067938 Manufacturer: Metav IndustryLine Label: Gauge pin, single, 13.32 mm diameter, length 50 mm Facts Diameter: 13.32 mm Length: 50 mm Weight: 0.1 kg Accuracy / tolerance: ±0.002 mm Category: Gauge pins (Messstifte) Special features Material: special steel Workshop execution (Werkstatt‑Ausführung) Supplied in a protective box for transport Single test pin for end‑measure checks Compact format for tight fixtures FAQ What is the declared tolerance of this gauge pin? The gauge pin M323.D32 is specified with a tolerance of ±0.002 mm, which defines the acceptable deviation from the nominal 13.32 mm diameter for inspection tasks. Is the pin suitable for repeated use in production checks? Yes, the special steel construction and workshop design make the test pin suitable for frequent insertion and withdrawal cycles common in production verification. Can the pin be used as a reference in comparator fixtures? The compact 50 mm length and stable diameter make the pin appropriate as a reference element in comparator setups and custom fixture applications. How does the protective box affect storage? The protective box is supplied to safeguard the pin during transport and handling; it offers short‑term protection but is not recommended as the primary long‑term storage solution for precision artefacts. Which industries or applications benefit most from this gauge pin? The pin is well suited to metalworking inspections, assembly line end‑measure checks and small‑part verification where a high‑precision diameter reference is required; it integrates easily with standard gauge sets and fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.33mm Gauge Pin, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop‑grade reliability and repeatable end‑measure checks through a combination of special steel construction, tight tolerance control and compact geometry; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D33 — 13.33 mm diameter, 50 mm length (Workshop version) The gauge pin M323.D33 is a single verification pin for precise end‑measure checks in workshop environments, designed as a robust workshop version for routine inspection and fixture testing. Workshop version, robust design Diameter 13.33 mm, precision ±0.002 mm Length 50 mm for standard end‑measure checks Supplied in protective transport case Precision for end‑measure verification The gauge pin M323.D33 offers a compact solution for accurate plug‑type inspections and end‑measure verification. With a nominal diameter of 13.33 mm and an indicated accuracy of ±0.002 mm, this pin is engineered for situations where tight tolerance control matters. Classified within the Micro range (10–100 mm), it is particularly suited to small components and fine mechanical assemblies where repeatability across multiple checks reduces rework and ensures consistent assembly fits. The short, stable geometry minimises bending and contributes to reproducible results when used in gauges, jigs or fixture setups. Built for workshop durability and easy handling Manufactured from special steel, the pin combines wear resistance with dimensional stability under routine workshop use. Its overall 50 mm length balances reach and stiffness, making it simple to handle during rapid inspection cycles while remaining resistant to distortion. Supplied in a protective transport case, the item is protected during storage and shipment, which preserves surface quality and measurement integrity. The workshop specification signals a focus on functionality and longevity rather than fragile laboratory finish, ensuring a practical tool for day‑to‑day quality control. Smooth integration into inspection processes This single verification pin integrates cleanly into existing inspection and fixture workflows, allowing straightforward assembly checks and go/no‑go validation steps. The compact form factor reduces the need for extensive fixture adaptations and the consistent diameter supports repeatable locating and alignment tasks. For procurement and stock management, Metav IndustryLine provides a reliable supply channel and a quality filter that serves the European market from Emmerich, helping workshops and small manufacturers maintain steady availability of essential inspection items. For bespoke bundle requirements or inventory planning, the M323.D33 can be listed by its SKU when coordinating orders. For workshop‑grade end‑measure verification and reliable supply, request availability from Metav Werkzeuge—phone +49 2822 7131930 or email info@metav-werkzeuge.com for tailored advice and rapid delivery Technical data Article number: M323.D33 GTIN: 4061905067945 SKU: M323.D33 Category: Gauge pins Facts Diameter: 13.33 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Material: Special steel Workshop version Single pin delivery Supplied in protective transport case FAQ What are the principal dimensions of this pin? The gauge pin M323.D33 has a diameter of 13.33 mm and an overall length of 50 mm. What accuracy can be expected during checks? The specified accuracy for the M323.D33 is ±0.002 mm, suitable for fine mechanical inspection tasks. What material is used for the pin? The M323.D33 is made from special steel and designed for workshop durability. Is the pin supplied ready for transport and storage? Yes, the M323.D33 is supplied in a protective transport case to preserve surface condition and dimensional integrity. Which applications suit this gauge pin? Designed for end‑measure checks and plug‑type inspections, the M323.D33 is classified as a micro gauge ideal for small components and fixture testing. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.34mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the ±0.002 mm accuracy and robust special steel in a compact 50 mm form to ensure consistent end‑measurement results; order the gauge pin directly via Metav Werkzeuge or request technical advice from our consultants. Gauge pin M323.D34 — 13.34 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.D34 designed for precise end‑measurements, inspection and workshop use *Precision tolerance ±0.002 mm *Special steel for durable contact *50 mm length for end‑measurement tasks Reliable repeatability for end‑measurement checks The ±0.002 mm specification gives this gauge pin a level of precision suitable for fine inspection tasks where repeatability matters. As a hardened, cylindrical reference, the pin is intended for consistent end‑measurement and fit checks in fixtures and gauges; the clearly defined 13.34 mm diameter provides a single, traceable datum that minimises ambiguity in pass/fail evaluations. Using a dedicated gauge pin for end dimensions reduces setup time and the risk of measurement scatter compared with improvised mandrels or worn reference plugs. Built for everyday workshop resilience Constructed from special steel and offered in a workshop‑grade configuration, the pin withstands routine handling and contact with mating parts. The compact 50 mm length balances rigidity and ease of handling, limiting deflection during seating and making the pin comfortable to position in tight inspection stations. Supplied as a single tool for direct use, the design focuses on long service life and repeatable contact surfaces, helping to maintain measurement quality across repetitive production processes. Easy integration into inspection workflows The single‑piece format fits straightforwardly into existing go/no‑go fixtures, plug gauges and assembly checks; its simple geometry streamlines gauging procedures and speeds throughput on the shop floor. Delivered with transport protection, the pin arrives ready for storage in a toolbox or for daily use at the bench, supporting a predictable inspection routine. Metav Werkzeuge’s sourcing and stock approach further reduces lead times and supports uninterrupted production by keeping precision references available when needed. Talk to Metav Werkzeuge in Emmerich for application advice and fast supply of the M323.D34 — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.D34 GTIN: 4061905068119 Manufacturer: Metav IndustryLine Facts Diameter: 13.34 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Single gauge pin for end measurements Delivered in protective transport case (plastic or wooden) FAQ What measurement accuracy does this gauge pin offer? The M323.D34 gauge pin is specified with an accuracy of ±0.002 mm, suitable for fine inspection and repeatability checks. Which material is used for the pin? The pin is made from special steel in a workshop‑grade finish, chosen for durable contact surfaces and longevity. For which tasks is this pin best suited? It is intended for end‑measurement checks, fit and assembly testing, and use as a reference plug in inspection fixtures. Is the gauge pin delivered with protective packaging? Yes, delivery includes a protective transport case (plastic or wooden) to safeguard the pin during shipment and storage. What are the article number and GTIN for ordering? Article number (SKU): M323.D34; GTIN: 4061905068119 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.35mm Test Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of workshop-grade robustness and high repeatability thanks to 13.35 mm diameter, 50 mm length and an accuracy of ±0.002 mm; order the gauge pin directly via Metav Werkzeuge or consult our experts for supply and application support. M323.D35 gauge pin — 13.35 mm Ø, 50 mm length (Metav IndustryLine) The M323.D35 is a single gauge pin designed for precise end measurements and reference checks in workshop and quality‑control environments. Gauge pin Ø 13.35 mm, length 50 mm Workshop-grade special steel construction Dimensional accuracy ±0.002 mm Compact format for end measurements Consistent precision for end‑of‑line inspection The compact design focuses on repeatable, measurable outcomes: with a diameter of 13.35 mm and a stated accuracy of ±0.002 mm, this pin is suited to tight tolerance checks where small deviations have large consequences. The specified tolerance supports reliable Go/No‑Go and reference measurements in fixtures and gauges, reducing rework and inspection time. As a single‑piece reference, the component minimises alignment ambiguity and simplifies the measurement workflow. Built for everyday workshop use Constructed from special steel and labelled as a workshop‑grade item, the pin balances toughness with dimensional stability. The 50 mm length provides sufficient engagement for end measurements while remaining easy to handle and store. The robust material choice helps resist surface damage during frequent seating and withdrawal operations, extending service life and lowering life‑cycle cost compared with softer test pieces. Simple integration into inspection routines Intended for end measurements and reference tasks, the pin slots easily into existing plug gauge sets, fixture pockets and bench checks. The clear specification of 13.35 mm and the compact format support efficient inventory management and rapid identification in busy quality departments. Traceability is supported by the offer of a manufacturer SKU and GTIN for catalogue procurement and process documentation. For workshop‑ready precision from Metav IndustryLine, contact Metav Werkzeuge GmbH in Emmerich for availability and tailored advice. Technical data Article number: M323.D35 GTIN: 4061905068928 Manufacturer: Metav IndustryLine Core data Diameter: 13.35 mm Length: 50 mm Weight: 0.1 kg Accuracy (tolerance): ±0.002 mm Special features Material: special steel Workshop version Intended use: end measurements FAQ What measurement tasks is this pin intended for? The M323.D35 gauge pin is intended primarily for end measurements and use as a reference or checking pin in workshop and quality‑control applications. What tolerance can be expected from this gauge pin? The pin is specified with a dimensional accuracy of ±0.002 mm, which supports repeatable checks for tight tolerance workflows. Which material is used for the pin and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability during frequent seating and removal. Can this gauge pin be used in fixture locating holes? Yes — the compact 50 mm length and accurate diameter make it suitable for locating, reference checks and integration in fixture pockets. How is the item identified for ordering and documentation? Order and documentation can reference the article number M323.D35 and GTIN 4061905068928 for unambiguous procurement and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.36mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise dimensional control with a 13.36 mm / 50 mm gauge pin that combines tight tolerance, robust material and safe transport packaging for reliable inspection workflows; order directly via Metav Werkzeuge or request application advice from our consultants. Gauge pin, single M323.D36 – 13.36 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin, single, 13.36 mm, length 50 mm is a precision test pin designed for end‑measurement and reference checks in workshop inspection and assembly environments. Precision tolerance ±0.002 mm Diameter 13.36 mm, length 50 mm Special steel for durability Supplied in protective case Precise checks that speed up inspection routines This gauge pin delivers repeatable dimensional checks thanks to a nominal diameter of 13.36 mm and a verified tolerance of ±0.002 mm. Such fine tolerance supports fast Go/No‑Go and reference measurements within quality control processes, reducing rework by making deviations visible at first inspection. The compact 50 mm length keeps handling straightforward while ensuring contact stability for end‑face and through‑hole assessments, helping to maintain steady production throughput. Built for workshop use and long service life Constructed from Special steel in a workshop version finish, the pin combines surface hardness with corrosion resistance appropriate for routine metrology tasks. The robust material choice enhances wear resistance during repeated engagement with housings and bores, extending service intervals and lowering replacement frequency. Supplied in a protective case, the pin arrives ready for storage or transport without risking surface damage, preserving measurement integrity between uses. Easy integration into inspection setups Designed as a straightforward reference element, this plug‑style test pin integrates with benches, fixture arrays and manual gauge sets. The consistent geometry of the shaft simplifies comparative measurement and calibration checks when used alongside other reference tools. By specifying a component with ±0.002 mm accuracy, inspection plans can rely on narrower acceptance bands and clearer pass/fail criteria, supporting tighter quality targets and traceable processes. Clear identification and handling information Product identification is straightforward for inventory and traceability: the item is listed under SKU M323.D36 and packaged for safe handling. The modest mass and compact dimensions mean the pin is convenient to include in inspection kits and portable measuring sets, providing a dependable reference that fits alongside other workshop gauges without adding bulk. Discuss application requirements with Metav Werkzeuge to ensure optimal use of this Metav IndustryLine gauge pin and arrange supply directly from our Emmerich site. Technical Data SKU: M323.D36 GTIN: 4061905068935 Brand: Metav IndustryLine Facts Diameter: 13.36 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Packaging: Supplied in protective case Category: Gauge pins (Messstifte) FAQ What are the exact dimensions of the pin? The gauge pin has a diameter of 13.36 mm and a length of 50 mm; identified as SKU M323.D36. What tolerance can be expected from this gauge pin? The pin is specified with a dimensional tolerance of ±0.002 mm. Which material is used for the pin? The shaft is made from Special steel in a workshop‑grade finish for enhanced durability. Is the pin delivered ready for safe storage and transport? Yes, the item is supplied in a protective case to prevent surface damage during storage and transit. What inspection tasks is this pin suited for? It is suitable for end‑measurement, reference checks and bore verification as part of routine workshop quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.37mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of workshop-grade precision and compact handling: the 13.37 mm diameter with a manufacturing variation of ±0.002 mm and the 50 mm overall length ensure repeatable gauging in inspection and assembly routines. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.D37 — 13.37 mm test pin, 50 mm length | Metav IndustryLine The Gauge pin M323.D37 is a single, workshop-grade test pin designed for accurate diameter checks and fit verifications in inspection, fixture and assembly operations. Workshop-grade for industrial use Diameter 13.37 mm with ±0.002 mm tolerance Length 50 mm, special steel construction Consistent accuracy for routine inspection needs The compact test pin delivers a 13.37 mm diameter with a verified manufacturing variation of ±0.002 mm, providing a reliable reference for pass/fail checks and gauge-fitting tasks. This level of dimensional control makes the pin suitable for repetitive inspection routines where small deviations influence assembly quality. The tight tolerance reduces rework and speeds up decision-making on the shop floor by giving measurable, comparable results that can be recorded in quality logs. Robust, workshop-ready construction that lasts Constructed from special steel in a workshop-grade finish, the pin is engineered for repeated handling and contact with mating parts. The 50 mm overall length offers secure grip without excessive overhang, improving repeatability when used with gauge blocks, fixtures or hand-held checking tools. Low mass (approx. 0.1 kg) and a compact profile simplify handling and storage in typical inspection kits while preserving surface integrity and roundness over many cycles. Practical integration into inspection flows Sold as a single test pin, this component integrates straightforwardly into existing gauge sets, assembly jigs and inspection benches. The clear labelling and traceable identifiers simplify inventory and part matching during process audits. Workshop environments benefit from the combination of small footprint and high repeatability, which supports quicker takt times in assembly verification and reduces the need for multiple compensating checks. Choose the Metav IndustryLine workshop-grade gauge pin for reliable, repeatable diameter checks and contact Metav Werkzeuge for procurement or technical guidance at info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.D37 GTIN: 4061905068942 Manufacturer: Metav IndustryLine Facts Diameter: 13.37 mm Length: 50 mm Accuracy variation: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop-grade (Werkstatt-Ausführung) Sales form: single test pin (einzeln) SKU: M323.D37 FAQ What applications is this test pin suited for? The M323.D37 gauge pin is suited for diameter verification, fit checks, fixture alignment and routine inspection tasks in production and workshop environments. How precise is the diameter of the pin? The pin is manufactured to a diameter of 13.37 mm with a variation of ±0.002 mm, providing consistent reference values for gauging and acceptance testing. What material is used for the pin and why does it matter? The pin is made from special steel, which offers high wear resistance and dimensional stability during repeated use in inspection and assembly operations. Is the pin supplied as part of a set or individually? This item is supplied as a single test pin; it is intended for standalone use or integration into existing gauge kits and fixtures. Can this pin be used with gauge blocks and fixtures? Yes, the compact 50 mm length and stable diameter make it compatible with standard gauge blocks, fixtures and jig checks commonly used in workshops. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.38mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop-grade test pin that combines 13.38 mm diameter accuracy, a ±0.002 mm tolerance and robust special-steel construction for reliable reference measurements; order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.D38 — gauge pin with 13.38 mm diameter and 50 mm length (Metav IndustryLine) Test pin M323.D38 is a precision reference pin for end-measure checks and small-part inspection, designed as a workshop-grade gauge pin for routine use in quality control and assembly environments Workshop-grade test pin Diameter 13.38 mm, length 50 mm Tolerance ±0.002 mm Special steel construction Reliable reference for small-part inspection and repeatable results The gauge pin serves as a stable reference for end-measure tasks, offering precision where repeatability matters. With a nominal diameter of 13.38 mm and a certified machining tolerance of ±0.002 mm, the component provides a clear measurement baseline for go/no-go checks and comparative gauging. The tight tolerance reduces uncertainty in pass/fail decisions and shortens inspection loops, which supports smoother production flow and faster in-line quality verification. Built for the workshop: robust material and ergonomic dimensions Constructed from special steel, this workshop-grade pin resists wear from frequent handling and maintains dimensional integrity during regular use. At 50 mm overall length and approximately 0.1 kg mass, the pin is compact yet sufficiently rigid for handheld gauging or for use in simple fixtures. The design balances stiffness and manageability to limit deflection during contact measurements, so operators can obtain repeatable readings without complex fixturing. Seamless integration into inspection processes and micro-range classification Classified for the micro measurement range (10–100 mm), the pin fits applications that demand compact gauges for small parts, such as fine mechanical components and precision assemblies. The simple geometry of the gauge pin allows straightforward use with micrometres, bore gauges and comparator setups, enabling quick verification of end dimensions. The design supports efficient inspection routines in workshops where space and handling speed are critical, and it complements existing metrology toolsets from Metav IndustryLine. Contact Metav Werkzeuge in Emmerich to discuss the suitability of the Metav IndustryLine test pin M323.D38 for specific inspection tasks, or request further technical details by phone at +49 2822 7131930 or via email at info@metav-werkzeuge.com Technical Data Article number: M323.D38 GTIN: 4061905068959 SKU: M323.D38 Facts Diameter: 13.38 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Category: Gauge pin / test pin Intended use: end-measure inspection FAQ What measurement tolerance does the test pin offer? The Metav IndustryLine test pin M323.D38 is manufactured to a tolerance of ±0.002 mm, providing a stable reference for fine inspection tasks. Is this pin suitable for handheld checks and small fixtures? Yes; the 50 mm length and compact diameter make the pin appropriate for handheld gauging and for use in basic fixture setups during routine inspection. What material is the pin made from and why does that matter? The pin is made from special steel, chosen for wear resistance and dimensional stability to ensure consistent performance through repeated use. Which measurement range category does this pin belong to? The pin falls into the micro measurement range (10–100 mm), which is ideal for precision work on small components and fine mechanical parts. Can the pin be used as a reference for go/no-go checks? Yes; the simple cylindrical geometry and tight tolerance make the pin suitable as a reference for go/no-go comparisons and basic pass/fail checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.39mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precision fit, workshop robustness and traceable repeatability for reliable end‑measure checks and fixture verification; the combination of a 13.39 mm diameter, a 50 mm shaft and a tolerance of ±0.002 mm supports consistent Go/No‑Go and gauge‑maker workflows. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.D39 – single test pin, 13.39 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.D39 is a single, workshop‑grade test pin designed for end‑measure checks, gauge inserts and fixture set‑ups in industrial maintenance and metrology benches. Workshop-grade design Diameter 13.39 mm precision Tolerance ±0.002 mm Ensure measurement certainty with micrometric tolerance control The pin delivers a tolerance of ±0.002 mm, providing a measurable advantage where repeatability determines part acceptance. Manufactured for dimensional stability, the test pin reduces uncertainty in Go/No‑Go checks and in gauge‑maker templates. This level of accuracy supports reliable pass/fail decisions during incoming inspection and in‑process controls, so measurement processes run with fewer rechecks and less downtime. The focus on numerical precision underpins the rational case for replacing worn or improvised pins with a verified gauge component. Built for workshop handling and long service life Made from special steel and finished for consistent surface quality, the pin resists everyday wear encountered in workshop use. The 50 mm length gives secure engagement in standard fixtures while limiting overhang, and the compact mass aids quick handling during repetitive checks. Robust construction means reduced risk of deformation under normal use, which preserves repeatability between operators and measurement cycles. The material choice and workshop execution combine to lower lifecycle maintenance and deliver practical durability where throughput and reliability are priorities. Simple integration into gauges, fixtures and inspection routines As a single test pin, this item suits insertion into pinbanks, plug gauges and dedicated fixtures for bore and shaft verification. The nominal 13.39 mm diameter enables a precise reference for mating parts and assembly checks and is particularly helpful when establishing master sizes or performing comparative trials. The straightforward geometry allows rapid replacement and minimal fixture redesign; standard mounting practices and common gauge housings will accept this pin with no special adaptation, supporting efficiency in both small shops and larger production environments. Secure workshop‑grade precision with Metav IndustryLine test pins—contact Metav Werkzeuge for specification matching and delivery details at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.D39 SKU: M323.D39 GTIN: 4061905068966 Label: Prüfstift, einzeln, 13,39 mm Länge 50 mm Facts Diameter: 13.39 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Workshop execution Category: Gauge pins Single test pin FAQ What is the declared tolerance of this test pin? The test pin is supplied with a declared tolerance of ±0.002 mm, which defines its permitted dimensional deviation for precision inspection tasks. Which material is the pin made from and what does that mean for durability? The pin is made from special steel, chosen for wear resistance and dimensional stability under normal workshop conditions, ensuring consistent long‑term performance. Can this pin be used in standard plug gauges and fixtures? Yes, the geometry and lengths are compatible with common gauge housings and fixture insertions, allowing the pin to be integrated without special adapters. Is the 13.39 mm size suitable for establishing master sizes? A diameter of 13.39 mm provides a reliable reference for master checks and comparative measurements where a matched nominal is required. Is the product supplied individually or in sets? This entry describes a single test pin item supplied individually; for set requirements, consult product listings or contact Metav Werkzeuge for options. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.41 mm Test Pin, Single, 50 mm Length Workshop Version - Metav IndustryLine
Precision workshop gauge pin with a 13.41 mm diameter, 50 mm length and an accuracy of ±0.002 mm provides repeatable end‑measure checks and robust daily use; supplied in a protective transport case and made from special steel for long service life. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin, 13.41 mm Ø, 50 mm Length – Metav IndustryLine The Gauge Pin, 13.41 mm Ø, 50 mm is a workshop‑grade precision pin for end‑measure verification and tight‑tolerance checking of small components Diameter 13.41 mm, accuracy ±0.002 mm 50 mm length, workshop design Supplied in a protective transport case Reliable end‑measure verification for small components The precision pin delivers measurable repeatability thanks to its ±0.002 mm tolerance, enabling reliable verification of bores, fits and end‑dimensions in production and inspection tasks. Such a tight tolerance corresponds to two micrometres of deviation allowance, which supports quality control where small variances affect assembly performance. By using a hardened and ground pin, the tool reduces uncertainty at the point of contact and helps maintain consistent production outcomes. Robust workshop construction for daily handling Manufactured from special steel, the unit is designed for everyday workshop use where resilience and surface integrity matter. The 50 mm shank length offers a practical balance between handling comfort and reach, while the workshop design resists wear under frequent insertion and extraction cycles. Classified for the Micro range (10–100 mm), this pin is particularly suited to fine mechanical tasks such as gauge setting, bore checking and fixture validation where compact, stiff measuring tools are required. Clear handling benefits and application scope The solid construction simplifies handling on the shop floor: one compact tool provides precise reference measurements for jigs, fixtures and incoming inspection. Supplied in a protective transport case, the pin stays protected during storage and transit, reducing the risk of damage that would alter its dimensional performance. As a gauge pin in the Messstifte category, it integrates readily into measurement routines that demand consistent contact geometry and minimal deformation under light manual force. Contact Metav Werkzeuge for tailored application advice and secure supply of the Metav IndustryLine 13.41 mm gauge pin; Metav Werkzeuge can advise on suitability for specific inspection tasks and arrange fast delivery from Emmerich. Technical Data SKU: M323.D41 GTIN: 4061905068980 Material: Special steel Weight: 0.1 kg Accuracy: ±0.002 mm Length: 50 mm Diameter: 13.41 mm Feature: Workshop version Delivery: Protective transport case Numbers / Core technical data Length: 50 mm Diameter: 13.41 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features / Applications Material: Special steel Workshop design for everyday use Suitable for Micro range measurements (10–100 mm) Protective transport case included Category: Gauge pin (Messstifte) FAQ What tolerance does this gauge pin offer? The gauge pin is specified with an accuracy of ±0.002 mm, providing micrometre‑level repeatability suitable for precision end‑measure checks. Is the gauge pin suitable for bore inspection on small parts? Yes. The 13.41 mm diameter and the 50 mm length make this gauge pin well suited to bore checking, fit verification and fixture validation in small component inspection. What material is used for the pin and how does it affect durability? The pin is made from special steel; this material ensures surface hardness and wear resistance, supporting long service life under frequent use. Does the product include protective packaging? The pin is supplied in a protective transport case to reduce the risk of damage during storage and transit and to help preserve dimensional accuracy. Which product identifiers should be quoted when ordering? Please quote the SKU M323.D41 and the GTIN 4061905068980 to ensure the correct gauge pin from the Metav IndustryLine is supplied. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.42mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Benefit from workshop-grade durability, a compact 50 mm length and a fine accuracy of ±0.002 mm for reliable end-dimension checks. Take advantage of the special steel construction and precise 13.42 mm diameter to maintain consistent production quality. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D42 — single test pin, Ø 13.42 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.D42 is a single precision test pin intended for end-dimension verification and alignment tasks in workshop and jig-making applications. Workshop version for robust use Diameter 13.42 mm Length 50 mm Accuracy ±0.002 mm Special steel construction Precise measurement where it matters The M323.D42 is engineered for repeatable end-dimension control, delivering a declared positional accuracy of ±0.002 mm. This level of precision places the pin firmly in the realm of fine workshop metrology, where small deviations can affect assembly fit or running clearance. Because the diameter is specified as 13.42 mm, it functions as a reliable reference in bore gauges, alignment jigs and verification fixtures. The clear numeric specification reduces ambiguity during quality checks and supports traceable inspection routines. Compact format for fine mechanical work With a 50 mm length and a diameter in the micro range, the pin belongs to the micro measurement category (10–100 mm). That classification means the tool is particularly suited to tasks that require high stiffness in a compact form: small bores, precision fixtures and components for subassemblies. The short overall length helps to keep bending and measurement uncertainty low, so measurements remain reproducible without complex support arrangements. Durability and workshop readiness Constructed from special steel, the pin has been designed for routine workshop use and frequent handling. The workshop version emphasises robustness while still preserving the dimensional stability required for reference checks. Supplied as a single test pin, it is easy to integrate into existing gauge sets or to use as a dedicated master for pass/fail tests. The material choice supports wear resistance, which helps maintain the nominal diameter over many inspection cycles. Practical benefits for production and quality control Using a dedicated test pin simplifies setup and shortens inspection time by providing a direct mechanical reference for go/no-go checks and alignment operations. The compact form factor and clear specification minimise setup errors and ease communication between production and quality teams. When paired with documented inspection procedures, the pin contributes to a predictable measurement process and fewer ambiguous results during incoming or in‑process checks. For procurement advice or stock information on the Metav IndustryLine gauge pin M323.D42, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to discuss availability and suitability for specific applications Technical data Article number: M323.D42 GTIN: 4061905069734 Brand: Metav IndustryLine Facts Diameter: 13.42 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Single piece supply Category: gauge pins / test pins Application: end-dimension checks FAQ What tolerance can be expected from this pin? The gauge pin M323.D42 is specified with an accuracy of ±0.002 mm, providing a fine tolerance suitable for precision workshop checks. What is the pin made of? The pin is manufactured from special steel, chosen for its wear resistance and dimensional stability in routine workshop use. Is the product supplied individually or as part of a set? This item is supplied as a single test pin (single piece), making it straightforward to use as a dedicated reference or to add to an existing set. Which measurement category does this pin fall into? With a diameter of 13.42 mm and a 50 mm length, the pin fits the micro measurement category (10–100 mm), ideal for fine mechanical and small‑part applications. How can the product be identified in orders or inventory? Identification is possible via the article number M323.D42 and GTIN 4061905069734 for unambiguous ordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.43mm Gauge Pin Length 50mm, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of tight dimensional control, robust workshop design and simple traceability for consistent end-measure checks; order the inspection pin directly via Metav Werkzeuge or contact our consultants for application support. Inspection pin M323.D43 — 13.43 mm diameter, 50 mm length (Metav IndustryLine) A Metav IndustryLine inspection pin for routine end‑measurement and gauge checks in workshop and inspection environments Workshop-grade inspection design Diameter 13.43 mm for accurate fits Tolerance ±0.002 mm for precision checks Precision where it counts for assembly and inspection The Metav IndustryLine inspection pin (M323.D43) is manufactured for applications that demand reproducible end‑measurement results. With a nominal diameter of 13.43 mm and a geometric tolerance of ±0.002 mm, the pin is intended for use as an end gauge or reference mandrel in assembly, inspection and go/no‑go testing. The controlled tolerance reduces measurement uncertainty during pass/fail checks and simplifies matching to mating bores or locating features. Built to withstand workshop routines while remaining easy to handle This single inspection pin combines a compact 50 mm length with a lightweight mass, making it straightforward to position in fixtures or measuring jigs. The workshop execution ensures surface and finish tolerances that tolerate frequent handling and insertion cycles without compromising fit. The compact geometry also supports use in confined setups where long probes would impede access, so operators benefit from quick, repeatable positioning during batch checks. Material selection and functional reliability explained Produced from special steel, the gauge pin offers a balance between surface hardness and dimensional stability, supporting repeated use in metalworking environments. The material choice minimises wear on contact surfaces while maintaining the required roundness and cylindricity for accurate fits. For traceability and inventory control, the item is supplied with its SKU and GTIN, enabling straightforward integration into quality documentation and inspection records. Practical integration into measuring workflows As a simple, robust reference element, the inspection pin suits a range of metrology tasks: end‑dimension verification, alignment of mating parts and use as a physical limit gauge in manual or semi‑automatic checks. The product’s measured form and tight tolerance support efficient decision‑making on the shop floor, reducing rework and supporting consistent assembly outcomes. Compatibility with common fixture designs and standard gauge blocks makes it a pragmatic choice for maintenance and small series production environments. Order the Metav IndustryLine inspection pin M323.D43 from Metav Werkzeuge for dependable workshop accuracy — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored technical advice Technical Data Article number: M323.D43 GTIN: 4061905069741 Manufacturer: Metav IndustryLine Material: Special steel Label: Inspection pin, single, 13.43 mm diameter, 50 mm length Numerical data Diameter: 13.43 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Workshop execution Single inspection pin Application: end measurement Category: Gauge pins / Messstifte FAQ What is the nominal diameter and tolerance of this inspection pin? The inspection pin has a nominal diameter of 13.43 mm and a stated tolerance of ±0.002 mm for precise end‑measurement tasks. Is the M323.D43 suitable for repeated use in a production environment? Yes, the M323.D43 is designed in a workshop execution with special steel to withstand frequent handling and insertion cycles while maintaining dimensional stability. Can this pin be used as an alignment or reference gauge? The inspection pin is suitable as an end gauge or reference mandrel for alignment, mating‑feature checks and simple go/no‑go evaluations in workshop settings. How is the product identified for traceability? The item is supplied with SKU M323.D43 and GTIN 4061905069741 for integration into inspection records and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.44mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Precision and durability in a compact format: the single gauge pin offers a 13.44 mm nominal diameter with a 50 mm overall length and an industrial tolerance of ±0.002 mm, ensuring reliable reference measurements in production and inspection. Benefit from a robust special steel construction and workshop-ready finish — order the single gauge pin M323.D44 directly via Metav Werkzeuge or ask our consultants if needed. Single gauge pin M323.D44 — 13.44 mm Ø, 50 mm length (Metav IndustryLine) Single gauge pin M323.D44 designed for reference measurements and go/no-go checks in workshop and small-series inspection tasks Accurate to ±0.002 mm 13.44 mm nominal diameter 50 mm overall length Delivered in protective transport box High-precision reference for repeatable checks The M323.D44 is built to provide repeatable dimensional references, with a verified tolerance of ±0.002 mm that places it in the high-precision class for gauging pins. Manufactured from special steel, the pin maintains roundness and dimensional stability under typical workshop handling, which reduces setup time for measuring routines and improves throughput during in-process checks. This mechanical reliability supports faster decision-making on the shop floor and fewer measurement-induced reworks. Compact design that suits micro-range inspection Classified within the micro range (measurement spans between 10 mm and 100 mm), the pin’s 13.44 mm diameter and 50 mm length combine reach with low bending sensitivity, making it suitable for fine mechanical tasks and small components. The compact dimensions ensure easy handling during fixture setup and manual gauging, while the workshop-oriented finish aids grip and alignment. The result is a practical inspection aid that simplifies handling without compromising metrological performance. Workshop-ready delivery and practical traceability Supplied as a workshop version and packaged in a protective transport box, this gauge pin is ready for immediate use at the bench or in assembly jigs. The robust packaging reduces risk during storage and transport and supports organised inventory management on the shop floor. As a Metav IndustryLine item, the pin benefits from accessible supply and the company’s quality filter in Emmerich, which helps ensure consistent availability and traceable sourcing for production-critical tools. Contact Metav Werkzeuge today to obtain the Metav IndustryLine single gauge pin M323.D44, check compatibility with specific measuring fixtures or request tailored advice from our consultants at the Emmerich team Technical data SKU: M323.D44 GTIN: 4061905069758 Category: Messstifte Facts Diameter: 13.44 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Delivered in a protective transport box Accuracy suited to fine inspection tasks FAQ What material is the gauge pin made from? The single gauge pin M323.D44 is manufactured from special steel, selected for dimensional stability and workshop durability. Is the tolerance of ±0.002 mm sufficient for precision inspection? Yes, the ±0.002 mm tolerance specified for this gauge pin positions it for precise reference measurements and reliable go/no-go checks in fine mechanical and workshop applications. Does the product come with a calibration certificate? This item is not indicated as supplied calibrated; a calibration certificate is only provided if the product is explicitly labelled as calibrated. For which applications is this gauge pin most suitable? The M323.D44 is best used for small-part inspection, fixture set-up and reference checks within the micro measurement range where compact dimensions and high repeatability are required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.45mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Combine ±0.002 mm tolerance with a compact 13.45 mm diameter and a 50 mm working length to secure reproducible fit checks and end-measurements; rely on the workshop-grade construction and specialist steel for long service life. Order the gauge pin directly via Metav Werkzeuge or consult our team for specification advice. M323.D45 gauge pin — 13.45 mm diameter, 50 mm length (Metav IndustryLine) The M323.D45 gauge pin is a workshop-grade checking pin designed for precise fit verification and end‑measurement tasks in production and inspection environments. Diameter 13.45 mm, tolerance ±0.002 50 mm length in workshop version Manufactured from special steel for durability Single item for individual inspection tasks Accurate fit control for assembly and inspection A ground checking pin with a declared tolerance of ±0.002 mm provides a reliable reference when verifying bore sizes and mating parts. The tight tolerance reduces uncertainty in go/no‑go decisions and shortens inspection cycles, which improves throughput in quality control. By converting dimensional data into clear pass/fail outcomes, the pin removes ambiguity from routine checks and supports traceable acceptance criteria for small series and batch production alike. Robust construction that endures workshop routines Manufactured in special steel and offered in a workshop configuration, this checking pin resists wear from repeated insertion and contact with common mating materials. The 50 mm length offers sufficient engagement for many fits while remaining compact for handheld use or bench fixtures; the modest mass also aids steady handling during manual inspections. This combination of material and design reduces the frequency of replacements and maintains measurement integrity over many cycles. Simple integration into quality workflows Marked and stocked under the SKU M323.D45 with an assigned GTIN for traceability, the pin is suited for standardised inspection procedures and documentation. Using a single, calibrated reference piece accelerates setup of comparative checks on production lines and simplifies tool lists for incoming inspection. The result is fewer process interruptions, faster decision-making at the inspection station and a more consistent record of conformity across repeating production steps. Contact Metav Werkzeuge for application advice or to arrange supply of the M323.D45 gauge pin and ensure the right fit verification tools for production needs Technical data SKU: M323.D45 GTIN: 4061905066016 Category: Gauge pins / Messstifte Manufacturer: Metav IndustryLine Facts Diameter: 13.45 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: Special steel Sold individually Suitable for end‑measurements and fit checks FAQ What tolerance does the gauge pin offer? The M323.D45 gauge pin is specified with a tolerance of ±0.002 mm, providing a high degree of repeatability for fit and end‑measurement applications. Which materials is the pin suitable for testing against? The checking pin, manufactured from special steel, is suitable as a reference for mating parts made of common engineering materials where a hard, wear‑resistant probe is required. Is the pin supplied as a single item or in sets? This article is supplied as a single item; the product is listed and stocked under SKU M323.D45 for individual inspection tasks. How does the pin support production inspection workflows? With a defined diameter and traceable identification (GTIN and SKU), the pin simplifies standard operating procedures and documentation for repetitive quality checks. Can the pin be used for assembly verification on small components? Yes, the compact diameter and 50 mm length make this gauge pin well suited to assembly and fit verification of small to medium components where controlled insertion depth is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.46mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise diameter control and minimal runout in a compact inspection element; the 13.46 mm diameter combined with a ±0.002 mm tolerance and 50 mm overall length supports repeatable end‑dimension checks in production and inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Gauge pin M323.D46 — 13.46 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin for precise end‑dimension verification and go/no‑go testing in workshop and inspection fixtures. Precision diameter 13.46 mm, tolerance ±0.002 mm 50 mm overall length for end‑face checks Made from special steel for wear resistance Reliable dimensional control for process stability The compact gauge pin delivers consistent dimensional references that reduce measurement uncertainty during frequent checks. With a nominal diameter of 13.46 mm and an indicated ±0.002 mm runout tolerance, the element provides the level of precision required for small‑part inspection and fixture alignment. The controlled tolerance helps to identify process drift early, improving first‑pass yield and reducing rework costs. Durable construction that keeps inspection intervals predictable Manufactured from special steel, the pin resists surface wear and preserves the reference diameter over repeated use. The material selection offers improved wear resistance compared with standard steels, which supports longer service life in high‑cycle inspection settings. The compact 50 mm length balances handling convenience with sufficient contact area for reliable end‑dimension verification. Simple integration into gauges and inspection jigs The gauge pin is suitable for insertion into fixture bores, stack gauges or as a reference plug in bench checks; its compact design enables quick interchangeability and minimal set‑up time. Marked with the internal SKU and traceable GTIN, the item simplifies inventory control and ensures reproducible identification across workstations. The low mass and straightforward geometry aid fast positioning while maintaining repeatability. Measurable benefits for workshop and production teams Using a tightly specified pin reduces subjective assessment in go/no‑go routines and supports objective acceptance criteria in quality documentation. The element's nominal dimensions and tolerance are suitable for precision fit checks, enabling faster decision cycles at incoming inspection and during in‑process verification. The robust finish reduces polishing and dressing frequency, lowering maintenance effort. Choose the Metav IndustryLine gauge pin M323.D46 for dependable, repeatable end‑dimension checks and contact Metav Werkzeuge for tailored advice on integrating this element into existing inspection fixtures Technical data Article number: M323.D46 GTIN: 4061905066023 Manufacturer: Metav IndustryLine Facts Nominal diameter: 13.46 mm Length: 50 mm Tolerance / runout: ±0.002 mm Weight: 0.1 kg Material: special steel Special features Workshop version (Werkstatt‑Ausführung) Single piece delivery Compact geometry for fixture insertion Traceable GTIN and SKU M323.D46 FAQ What inspection tasks is this gauge pin best suited for? It is ideal for end‑dimension verification, go/no‑go checks and fixture alignment where a compact, precision pin with 13.46 mm nominal diameter is required; the Metav IndustryLine gauge pin M323.D46 supports quick, repeatable checks. How accurate is the diameter of the pin? The pin is specified with a runout/tolerance of ±0.002 mm, which enables high repeatability for small‑part inspection and reduces ambiguity in pass/fail assessments. What material is the pin made from and why does it matter? Made from special steel, the gauge pin offers enhanced wear resistance compared with standard grades, extending service life and preserving reference dimensions under frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.47mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the workshop-grade build, tight ±0.002 mm accuracy and compact 13.47 mm diameter for reproducible end‑measure checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin (single) – 13.47 mm, 50 mm length (Metav IndustryLine) The gauge pin 13.47 mm is a workshop-grade inspection pin for precise end‑measure verification and hole gauging in component checks. Workshop-grade design for daily use Diameter 13.47 mm with ±0.002 mm accuracy Length 50 mm for recessed measurements Supplied in transport case Precision that speeds routine inspection This inspection pin delivers a measured outcome thanks to its ±0.002 mm specification, reducing uncertainty during rapid go/no‑go checks and repeat measurements. The compact 13.47 mm diameter is suited to fine hole gauging and end‑measure verification in assembly and machining operations; the close tolerance translates into fewer rechecks and a smoother quality workflow. The result is quantifiable time savings in standard inspection cycles. Robust workshop design for everyday handling Constructed from special steel and offered in a workshop version, the pin resists wear during frequent insertion and offers consistent contact geometry over repeated use. The 50 mm length provides reach into recesses while maintaining a rigid profile that limits bending. Supplied in a protective transport case for safe movement between workstations, the tool is set up for practical shopfloor use without additional packaging effort. Simple integration into existing inspection routines As a single measuring pin, it functions as a reliable reference gauge for production sampling, first‑article checks and occasional verification of hole diameters. The compact format supports handheld gauging as well as fixture‑based checks; its reproducible dimensions make it a practical complement to calipers and bench gauges, enhancing throughput in standard quality control tasks. Clear technical attributes for procurement and traceability The pin’s straightforward specification—13.47 mm diameter, 50 mm overall length and ±0.002 mm dimensional variation—makes it easy to compare with existing standards and procurement lists. The modest mass and compact footprint simplify storage and handling on the shopfloor. For teams focused on reproducible inspection outcomes, this measuring pin provides a low‑complexity, high‑precision option. For Metav IndustryLine precision and workshop suitability, contact Metav Werkzeuge in Emmerich for tailored advice and ordering: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.D47 GTIN: 4061905066030 Manufacturer: Metav IndustryLine Weight: 0.1 kg Facts Diameter: 13.47 mm Length: 50 mm Accuracy: ±0.002 mm Mass: 0.1 kg Special features Material: Special steel Workshop version Supplied in transport case (plastic or wooden) Category: Gauge pin / Measuring pin FAQ What applications suit this gauge pin best? The gauge pin M323.D47 is ideal for end‑measure verification, hole gauging and routine go/no‑go checks in machining and assembly workflows. Is the dimensional accuracy suitable for standard workshop control? Yes; the ±0.002 mm accuracy of this Metav IndustryLine measuring pin meets tight workshop tolerances for component inspection and sampling. How is the pin supplied and stored? The inspection pin is supplied in a protective transport case (plastic or wooden) to protect the contact geometry during handling and storage. What material is used for the pin and why does that matter? Made from special steel, the pin offers wear resistance and stable contact surfaces, supporting reproducible measurements over time. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.49mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a workshop‑grade construction, 13.49 mm diameter accuracy and a compact 50 mm length for reliable end‑measurement checks; order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.D49 — gauge pin Ø 13.49 mm, 50 mm length (Metav IndustryLine) A Test pin M323.D49 designed for precise end‑measurements and fixture checks in workshop and inspection environments Workshop version, robust design Diameter 13.49 mm, precision ±0.002 Compact 50 mm length for tight fixtures Reproducible checks with industrial accuracy The gauge pin delivers high repeatability thanks to its tight manufacturing tolerance of ±0.002 mm, which supports quantitative go/no‑go and end‑dimension assessments. In practical terms, this level of control converts into fewer reworks and faster setup times on the shop floor: a stable reference dimension reduces variation when aligning fixtures or verifying bore sizes. The design is therefore particularly suitable where measurable, documentable results are required for quality control processes. Robust construction for daily workshop use Built as a workshop version, the pin is made from special steel to withstand handling and routine use. The material choice prioritises wear resistance and dimensional stability under normal operating conditions; this means less frequent replacement and maintained accuracy over many inspection cycles. The compact format and balanced mass ensure the pin is easy to position in jigs and comparators while resisting minor knocks and scratches that commonly occur in production environments. Small footprint, wide applicability With a diameter of 13.49 mm and a length of 50 mm, the pin is optimised for confined spaces and smaller assemblies where bulkier gauges are impractical. Its geometry makes it useful for end‑measurement, checking plug fits, and verifying mating components in assemblies. The single‑piece supply format (individual pin) keeps inventory flexible: it can be incorporated into bespoke sets or used as a stand‑alone reference for targeted inspection tasks. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich (+49 2822 7131930, info@metav-werkzeuge.com) for procurement advice and reliable supply to the workbench Technical data SKU: M323.D49 GTIN: 4061905066054 Manufacturer: Metav IndustryLine Material: Special steel Special feature: Werkstatt‑Ausführung Story trigger: endmasse Facts Diameter: 13.49 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Supplied individually Suitable for end‑measurement and plug checks Compact form factor for tight fixtures FAQ What tolerance can be expected from the M323.D49? The M323.D49 gauge pin is manufactured to a tolerance of ±0.002 mm, offering the precision required for fine measurement tasks in workshop inspection routines. Which material is used for this gauge pin? The pin is produced from special steel, providing a balance of wear resistance and dimensional stability for repeated checking operations. For which applications is this test pin intended? This gauge pin is intended for end‑dimension checks, plug‑fit verification and fixture alignment in workshop and light production settings; its workshop version construction supports everyday use. Is the pin delivered as part of a set or individually? The product is supplied as an individual test pin (SKU M323.D49), allowing integration into custom inspection sets or use as a single reference gauge. How should the pin be handled to maintain accuracy? Handle the pin with care to avoid contamination and impact; store it clean and dry and inspect surfaces before measurement to preserve the ±0.002 mm accuracy. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.4mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, compact workshop design and robust material for dependable end‑dimension checks; the precision of ±0.002 mm reduces rework and speeds quality decisions. Order the gauge directly via Metav Werkzeuge or ask the consultants for application advice. Single pin gauge M323.D40 — 13.4 mm diameter, 50 mm length (Metav IndustryLine) The single pin gauge M323.D40 is a compact inspection pin for fast end‑dimension verification in workshop and production environments High repeatability ±0.002 mm Diameter 13.4 mm for tight fits 50 mm hardened length for stable support Workshop version made from special steel Precision that shortens inspection cycles The compact inspection pin is designed for decisive dimensional checks where repeatability and clear tolerances matter. With a stated variation of ±0.002 mm, the gauge pin delivers measurement certainty that supports faster go/no‑go decisions on the shop floor and reduces downstream rework. The controlled diameter of 13.4 mm combined with a 50 mm length provides sufficient engagement depth for most end‑dimension checks while remaining easy to handle. This makes the tool particularly effective in series inspection, jigs and fixture checks where quick validation is required rather than lengthy measurement setups. Built for workshop handling and durability Constructed in special steel and specified as a workshop execution, the pin gauge resists everyday wear and maintains form under routine use. The design prioritises secure seating in fixtures and comfortable handling during repetitive tasks, supporting steady workflows in machining and assembly operations. Weight and balance have been tuned to ensure stable placement during inspection; the solid construction helps maintain dimensional stability over many cycles, giving a consistent reference that teams can rely on for serial checks and final inspections. Integrates with measurement routines and documentation The pin gauge fits into existing inspection processes as a stable reference instrument. Marked with SKU M323.D40 and traceable by GTIN 4061905068973, the part is straightforward to catalogue in quality systems and batch records. Its compact geometry reduces setup time compared with larger gauges, allowing technicians to validate bores and seating faces quickly. When used alongside calibrated gauges and documented control plans, this single pin gauge supports repeatable results and clear audit trails for internal quality control. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss suitability for specific inspection tasks or to request the M323.D40 pin gauge directly. Technical data SKU: M323.D40 GTIN: 4061905068973 Category: Messstifte Facts Diameter: 13.4 mm Length: 50 mm Variation / Repeatability: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Version: workshop execution Application: end‑dimension checks, fixture verification FAQ What tolerance class does this pin gauge provide? The supplied single pin gauge offers a variation of ±0.002 mm, making it suitable for tight workshop inspections where high repeatability is required. Is the material corrosion‑resistant for humid environments? The gauge is manufactured from special steel and specified in a workshop execution; further surface protection options can be checked with Metav Werkzeuge if environmental resistance is required. Can this gauge be used for bore verification and seating checks? Yes, the 13.4 mm diameter and 50 mm engagement length are suitable for many bore verifications and seating face checks in fixtures and jigs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.51mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade measuring reference that combines 13.51 mm nominal diameter, a 50 mm length and a confirmed ±0.002 mm dimensional tolerance for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Pin gauge, single, 13.51 mm, length 50 mm (M323.D51) — workshop version, special steel The pin gauge, single, 13.51 mm, length 50 mm is a hardened test pin intended for precision end‑measure inspection and gauge setting in workshop and production metrology. Workshop version for rugged use Diameter 13.51 mm with ±0.002 mm accuracy Length 50 mm for reach and stability Reliable dimensional reference for everyday workshop control This workshop‑grade gauge pin provides a stable reference for end‑measure tasks and quick dimensional checks. The declared ±0.002 mm accuracy positions the pin as a high‑precision reference suitable where repeatable, traceable checks are required. Made from special steel, the pin resists routine wear and maintains its profile under typical workshop handling. The compact geometry and 50 mm length deliver a practical balance of reach and rigidity, reducing bending and measurement variation during use. Compact format with industrial precision for small components Classified in the micro measuring range (10–100 mm), this pin is optimised for fine mechanical parts and assembly jigs where space is limited but tolerance demands are high. The nominal 13.51 mm diameter gives a definitive mating size for end‑measure and plug checks, while the workshop specification ensures compatibility with bench fixtures, gauge blocks and sizing inserts. The simple, single‑pin format is convenient for sorting, go/no‑go checks and rapid process verification without the overhead of complex fixturing. Durable design and practical delivery for immediate deployment Built as a workshop execution item, the pin combines a hardened surface finish with a geometry that supports repeatable touch and feel measurements over many cycles. Delivery includes a protective case to safeguard the pin in transit and storage, ensuring the measuring face stays free of damage prior to use. Lightweight at approximately 0.1 kg, the pin is easy to handle and integrates smoothly into inspection kits and portable measuring sets, making it a reliable tool for production lines and maintenance benches. Choose Metav IndustryLine pin gauges from Metav Werkzeuge for dependable workshop measurement—contact our specialists via info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and ordering support. Technical Data Article number: M323.D51 GTIN: 4061905067013 Manufacturer: Metav IndustryLine Weight: 0.1 kg Core specifications Nominal diameter: 13.51 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Category: Gauge pin (Messstifte) Special features Material: special steel Workshop version (robust execution) Delivered in protective case Suitable for end‑measure and gauge setting FAQ What applications suit this gauge pin best? This gauge pin is ideal for end‑measure inspection, plug checks and gauge setting in workshop and production environments; the Metav IndustryLine pin gauge M323.D51 is optimised for small components and fixture checks. Is the nominal diameter exactly 13.51 mm? Yes, the pin is specified as 13.51 mm nominal diameter and is manufactured to an accuracy of ±0.002 mm to ensure a precise reference size. Does the pin come ready for use or is additional preparation required? The Metav IndustryLine pin gauge is delivered in a protective case and ready for immediate use; routine cleaning before first use is recommended to remove handling residues. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.52mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Combine 13.52 mm diameter, 50 mm length and a tight ±0.002 mm tolerance to ensure repeatable end‑measure checks and faster set‑up times; robust special steel construction suits workshop use. Order directly via Metav Werkzeuge or consult our advisors for application support. M323.D52 Gauge pin — 13.52 mm diameter, 50 mm length (Metav IndustryLine) M323.D52 Gauge pin is a single precision pin for end‑measure verification and fixture alignment in inspection and production environments Single 13.52 mm gauge pin Length 50 mm for deep bore checks High repeatability with ±0.002 mm tolerance Workshop version for daily use Repeatable measurements that reduce downtime The compact geometry and the nominal 13.52 mm diameter, combined with a ±0.002 mm specification, make this pin a reliable reference for end‑measurements and go/no‑go verifications. Built to deliver consistent contact geometry over repeated cycles, the component helps to reduce measurement scatter and downstream rework. The controlled tolerance translates directly into fewer set‑up iterations on production lines and a steadier output quality in inspection routines. Durable construction for everyday workshop conditions Manufactured from special steel and supplied in a workshop configuration, the pin stands up to routine handling and frequent insertion cycles. The 50 mm length offers sufficient engagement for many fixture and bore checks while remaining compact for easy storage. The weight and balance support stable seating during measurement, which contributes to consistent readings and a longer service life under regular shopfloor conditions. Straightforward use across inspection and assembly tasks As a single precision test pin, the item is suitable for end‑measure checks, gauge setting and fixture verification across inspection, assembly and production stages. The simple, single‑piece design ensures fast positioning and minimal adjustment time, allowing teams to maintain throughput without sacrificing measurement confidence. Its form factor also eases integration into existing gauge sets and modular test fixtures. Traceability and identification for process control Identification by SKU M323.D52 and GTIN is available for inventory and process traceability. The clear technical specification supports documentation in quality records and assists in maintaining consistent inspection standards across shifts. The construction and stated tolerance support the rational decision to standardise on a single reference pin where repeatable end‑measure control is essential. For precision end‑measure checks, rely on Metav IndustryLine quality—contact Metav Werkzeuge in Emmerich for ordering details and technical guidance Technical data SKU: M323.D52 GTIN: 4061905067020 ECLASS: 21170231 Facts Diameter: 13.52 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Item type: Single gauge pin Intended use: End‑measure checks, fixture alignment FAQ What applications is this gauge pin suitable for? This M323.D52 gauge pin (Metav IndustryLine) is intended for end‑measure verification, fixture alignment and gauge setting in inspection and production contexts. Is the stated ±0.002 mm accuracy sufficient for precision inspection tasks? Yes, the ±0.002 mm specification provides a high level of repeatability appropriate for precision end‑measure checks and for reducing set‑up variability in manufacturing. Which material is the pin made from and what benefit does this provide? The pin is made from special steel, which offers robust performance for daily workshop handling and prolonged engagement cycles. How is the product identified for stock and quality records? Identification is via SKU M323.D52 and GTIN 4061905067020, supporting straightforward traceability in inventory and quality documentation. Can this test pin be integrated into existing gauge sets? The single‑piece design and standard form factor make the pin easy to integrate into modular fixtures and gauge sets used for routine inspection and assembly. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.53mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the 13.53 mm diameter and ±0.002 mm tolerance in a compact, workshop-grade design to secure repeatable reference measurements; the 50 mm length offers easy handling and insertion depth for bore checks. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin, single 13.53 mm (50 mm length) – workshop-grade precision from Metav IndustryLine A gauge pin, single 13.53 mm (50 mm length) designed for end‑measure verification and bore checking in workshop metrology, combining compact handling with tight dimensional control Workshop-grade execution Diameter 13.53 mm with ±0.002 mm tolerance 50 mm special steel length for stable handling Single pin for reference and inspection tasks Precision that reduces uncertainty on the shop floor With a nominal diameter of 13.53 mm and a stated tolerance of ±0.002 mm, this single gauge pin functions as a stable reference for go/no‑go checks and alignment tasks. The tight tolerance limits measurement scatter and supports quality control routines where repeatability matters. Such accuracy is especially valuable in small‑bore inspection, pin gauges for fixture alignment, and final inspection steps where a compact reference element simplifies comparison to nominal values. The clear numerical specification enables straightforward inclusion in inspection protocols and process sheets. Built for regular workshop use and straightforward handling The workshop execution reflects a focus on durability and everyday usability: manufactured from special steel, the pin maintains dimensional stability during normal handling and routine use. Its 50 mm length gives sufficient insertion depth while remaining easy to manipulate by hand or with simple clamping devices. The modest mass makes the item convenient for frequent checks without adding handling fatigue, and the single‑piece design minimises features that could trap debris—helping to maintain consistent contact and reproducible results across repeated measurements. Practical applications and process benefits This single gauge pin serves several clear roles in a production environment: reference checking of bores, end‑dimension verification, and use as a datum in quick inspection jigs. As a compact reference element it speeds up routine checks, reducing machine downtime caused by lengthy measurement procedures and allowing faster decision points on accept/reject flows. The combination of a defined 13.53 mm nominal size and ±0.002 mm tolerance supports traceable in‑process control and simplifies documentation when integrating the pin into quality records or inspection plans. Choose the Metav IndustryLine gauge pin for reliable 13.53 mm reference measurement and contact Metav Werkzeuge for tailored application advice and rapid supply Technical data Article number: M323.D53 GTIN: 4061905067037 Brand: Metav IndustryLine Core dimensions Diameter: 13.53 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & features Material: Special steel Special feature: Workshop execution Category: Gauge pins (Messstifte) Accuracy class: ±0.002 mm FAQ What is the primary use of this gauge pin? The single gauge pin M323.D53 is intended for bore checking, end‑measure verification and use as a compact reference in inspection jigs. Does the pin provide traceable tolerance information? The M323.D53 from Metav IndustryLine is specified with a tolerance of ±0.002 mm, suitable for workshop calibration and process checks; a calibration certificate can be requested if required for documentation. What material is the gauge pin made from and how does that affect use? Made from special steel, the pin offers dimensional stability under normal workshop handling and resists minor wear during routine inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com