Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
13.54mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of workshop-grade durability, Ø 13.54 mm sizing and a ±0.002 mm tolerance to keep inspection and fixturing tasks consistent; order the gauge pin directly via Metav Werkzeuge or consult our technicians for application advice. Gauge pin M323.D54 — Workshop inspection pin, Ø 13.54 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.D54 is a single, workshop-grade inspection pin intended for dimensional checking, fixture alignment and reference gauging in production and quality-control environments Workshop-grade construction for daily use Diameter 13.54 mm for precise fit checks Tolerance ±0.002 mm for high-precision checks Reliable dimensional control for small bores and fits The pin delivers repeatable alignment and verification where tight clearances matter: with a Ø 13.54 mm diameter and 50 mm usable length, it is configured for accurate insertion and measurement of bores, dowel seats and mating parts. The specified ±0.002 mm tolerance denotes the manufacturing limit for deviation and supports reliable go/no-go assessments and comparative checks on the shop floor. This makes the pin suitable for routine inspection tasks that require consistent, quantifiable results rather than subjective judgement. Durable workshop design that suits daily handling Manufactured from special steel, the component is produced for dimensional stability and resistance under frequent use. The workshop version specification indicates a construction geared towards everyday handling and storage in industrial environments, combining practical robustness with the precise geometry necessary for insertion and withdrawal without compromising fit. As a single-unit supply, the pin is straightforward to replace or stock as a spare part in maintenance kits and inspection drawers. Traceability and simple integration into QC workflows Supplied as an individual inspection pin, the item supports clear inventory and traceability: the M323.D54 SKU and GTIN enable straightforward ordering and record keeping within quality-management systems. The compact 50 mm length eases manual handling and placement in jigs or fixtures, while the tight tolerance reduces measurement uncertainty when used as a reference or master pin. For tasks from assembly checks to in-process verification, this pin offers a low-complexity solution that aligns with standard metrology procedures. For dependable workshop measurement with Metav IndustryLine quality, request the M323.D54 gauge pin from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for availability and technical guidance Technical Data SKU: M323.D54 GTIN: 4061905067044 Label: Prüfstift, einzeln, 13,54 mm Länge 50 mm Facts Diameter: 13.54 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Special features Material: special steel Workshop version Supplied as single unit FAQ What applications suit this gauge pin best? The M323.D54 gauge pin is ideal for bore checking, fixture alignment and fit verification in production and inspection processes. What tolerance can be expected from this inspection pin? Tolerance is specified as ±0.002 mm, which supports high-precision checks and reproducible comparative measurements. Is the pin supplied individually or in sets? This item is supplied as a single unit, making it suitable for selective replacement or stocking as a spare part. Which material is used for the pin and why does it matter? The pin is made of special steel, chosen for dimensional stability and wear resistance under repetitive insertion and extraction. How is the item identified for ordering and traceability? The product can be ordered using SKU M323.D54 and GTIN 4061905067044 for clear traceability in inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.55mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high repeatability and compact handling thanks to the 13.55 mm diameter, ±0.002 mm tolerance and robust special steel construction; the compact gauge pin arrives in a protective transport case and can be ordered directly via Metav Werkzeuge or discussed with our technical consultants. Gauge pin M323.D55, single — 13.55 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.D55 is a workshop-grade cylindrical test pin for end-face checks, fit verification and assembly inspections in production and maintenance environments. Single gauge pin 13.55 mm diameter Workshop-grade special steel construction Precision tolerance ±0.002 mm Supplied in protective transport case Reliable fit checks for assembly and inspection A compact cylindrical test pin provides a dependable reference for go/no-go assessments and shaft-fit checks. The 13.55 mm nominal diameter with a tolerance of ±0.002 mm ensures that dimensional verifications are consistent across repeated measurements, reducing the risk of assembly rejects. The workshop design permits quick handling on the shop floor, while the solid construction keeps deformation low during routine use. This combination supports faster quality decisions and lower rework rates in mechanical assembly and maintenance operations. Consistent measurement accuracy under workshop conditions Precision is the primary rational advantage of this tool: the specified tolerance translates into measurable control for clearance and interference checks. The material selection—special steel—maintains surface integrity under frequent contact and resists wear that would otherwise alter the functional size. By using a dedicated measurement pin instead of improvised substitutes, inspection routines gain traceable repeatability and a clear pass/fail criterion, which streamlines quality documentation and speeds up throughput in production and repair tasks. Practical handling and secure storage for everyday use At 50 mm overall length the pin balances reach with manoeuvrability, making it suitable for confined assemblies as well as bench inspections. Delivery in a protective transport case preserves the finished surface and ensures safe storage between uses, so calibration drift and handling damage are minimised. The workshop-oriented configuration supports frequent deployment by technicians and inspectors, offering a robust, low-complexity solution that integrates smoothly into established inspection workflows. Contact Metav Werkzeuge for stock availability and tailored technical advice on the M323.D55 gauge pin, shipped from Emmerich with reliable supply and expert support Technical data SKU: M323.D55 GTIN: 4061905067051 Category: Messstifte Key measurements Diameter: 13.55 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Features & materials Material: Special steel Version: Workshop execution Delivery: Protective transport case Image file: m323a01-main.jpg FAQ What checks is this gauge pin best suited for? The M323.D55 gauge pin is intended for end-face checks, fit verification and quick go/no-go assessments in assembly and inspection tasks. Is the accuracy of the pin suitable for fine mechanical work? Yes, the specified ±0.002 mm tolerance makes the M323.D55 suitable for demanding workshop inspections where tight dimensional control is required. How is the pin delivered and protected during transport? The test pin is supplied in a protective transport case to preserve the measuring surface and prevent handling damage. Can the M323.D55 be used for routine machine shop inspections? The workshop-grade construction and nominal dimensions of the M323.D55 make it practical for repetitive checks on shafts, housings and assembly fittings in machine shops. Which material is used and why does it matter? Constructed from special steel, the pin offers good surface hardness and wear resistance, maintaining dimensional stability over frequent use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.56mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
Precise, compact and workshop‑graded: the combination of ±0.002 mm tolerance, 13.56 mm diameter and 50 mm length provides a reliable reference for end‑dimension verification and fixture alignment; order the test pin directly via Metav Werkzeuge or consult our specialists for application advice. Test pin, single, 13.56 mm diameter, length 50 mm (M323.D56) The Test pin, single, 13.56 mm, length 50 mm (M323.D56) serves as a precision gauge pin for end‑measure verification, alignment and plug‑gauge tasks in workshop and inspection environments Precision ±0.002 mm tolerance Diameter 13.56 mm for end‑measure checks 50 mm overall length for compact fixtures Workshop version in special steel Engineered for dependable end‑dimension verification The gauge pin is produced to a tight ±0.002 mm manufacturing tolerance, making it suitable as a reference element in repetitive inspection tasks where reproducible results are required. With a nominal diameter of 13.56 mm, the pin functions as a standardised plug for checking final dimensions and seating in bores or sockets; the narrow tolerance reduces the risk of false rejects and supports faster decision cycles on the shop floor. The construction emphasises dimensional accuracy and consistent repeatability rather than decorative finishes, which benefits quality control routines and process stability. Compact design that suits fixtures and inspection rigs At 50 mm overall length and weighing approximately 0.1 kg, the component offers a low‑profile solution for confined set‑ups and fixture blocks. The special steel composition grants mechanical robustness under frequent insertion and removal, while the short form factor helps maintain alignment integrity in tight assemblies. This compact, workshop‑grade configuration simplifies handling and reduces set‑up time compared with longer or heavier reference pins, so throughput in small‑batch inspection and jigs is improved without compromising measurement certainty. Reliable integration into production and measurement workflows Designed for straightforward use in end‑measure control, the pin complements common plug‑gauge and alignment procedures; it is appropriate for controlled checks during assembly, final inspection and part acceptance. The production tolerance and simple geometry make the element compatible with established metrology equipment and manual verification steps, providing a clear pass/fail reference or a repeatable datum. The workshop specification supports frequent, practical use where traceable results and limited handling complexity are priorities. Contact Metav Werkzeuge for ordering details or application support for the Metav IndustryLine test pin M323.D56 with 13.56 mm diameter and ±0.002 mm precision and ensure the correct reference parts are supplied for the inspection task at hand Technical Data Article number: M323.D56 GTIN: 4061905067068 Label: Test pin, single, 13.56 mm, length 50 mm Facts Diameter: 13.56 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Material: Special steel Special features Workshop version Suitable for end‑dimension verification Compact form for fixture integration FAQ What tolerance does this gauge pin provide and what does it mean for inspection? The test pin is manufactured to a ±0.002 mm tolerance; this level of precision delivers a stable reference point for end‑dimension checks and reduces measurement variability in routine inspection workflows with the Metav IndustryLine M323.D56 test pin. Is the material suitable for frequent use in a workshop environment? Yes, the M323.D56 is made from special steel and specified as a workshop version, giving mechanical resilience for repeated insertion and handling in fixtures and measurement set‑ups. Can this pin be used as a plug gauge for bore verification? The 13.56 mm diameter and tight tolerance make the pin appropriate as a plug‑type reference for bore seating and end‑measure verification within compatible inspection procedures. Does the product come with traceability or calibration documentation? The product data does not indicate supplied calibration certificates; any calibration or traceability requirements should be confirmed with Metav Werkzeuge prior to purchase to ensure alignment with specific quality system needs. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.57mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
A compact gauge that combines tight dimensional control and workshop robustness: the precise 13.57 mm diameter and ±0.002 mm tolerance ensure reproducible end‑measure checks, while the 50 mm shaft and special steel construction withstand routine use; order the gauging pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauging pin M323.D57 – Test pin, Ø 13.57 mm, 50 mm length (Metav IndustryLine) A gauging pin (M323.D57) designed for fast end‑dimension checks and go/no‑go inspection in workshop environments Workshop version for everyday use Diameter exactly 13.57 mm for end‑dimension checks 50 mm length for stable engagement Accuracy ±0.002 mm for reproducible results Precision that lowers inspection uncertainty The inspection pin delivers a reliably repeatable reference with a stated accuracy of ±0.002 mm, making it suitable where small deviations affect assembly or fit. The defined 13.57 mm measuring dimension is provided as a fixed end‑measure, reducing interpretation in routine checks and accelerating process control. Using a dedicated gauging element simplifies decision chains in quality control: the measured result is clear, the need for rework is reduced and the throughput of inspection stations is increased, which supports leaner production cycles. Robust construction for workshop routines Manufactured from special steel, the pin is configured as a workshop version that balances durability with handling comfort. The 50 mm shaft provides sufficient engagement depth for many end‑measure applications while remaining compact for fast manual use. The listed mass of 0.1 kg gives a stable feel without unnecessary bulk. Where repeated insertion and withdrawal occur, this construction reduces wear on mating surfaces and keeps replacement intervals low, which contributes to predictable maintenance planning. Practical benefits for process control As an individual test pin, this product fits into both dedicated inspection fixtures and ad‑hoc checks at the machine or assembly bench. It is intended specifically for end‑dimension verification and is therefore effective for quick go/no‑go decisions, first‑article checks and in‑process sampling. The clear numeric specification and single‑dimension design lower the operator training threshold and shorten measurement cycles, delivering a measurable productivity gain on routine inspection tasks. Traceability and workshop logistics The pin is supplied as a single item with clear identification via SKU M323.D57 and GTIN 4061905067952, which eases stock keeping and traceability in ERP systems. Delivery includes a transport case to protect the gauge in transit and storage, reflecting the workshop focus on robustness and ease of handling. The combination of distinct labelling and protective packaging supports orderly shelf management and fast retrieval during production. Contact Metav Werkzeuge for supply and application support on the Metav IndustryLine M323.D57 gauging pin—the team in Emmerich will advise on suitability and delivery options Technical data Article number: M323.D57 GTIN: 4061905067952 Manufacturer: Metav IndustryLine Core dimensions Diameter: 13.57 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Material: special steel Workshop version Supplied in transport case Single, individual test pin FAQ What is the intended use of this gauge? The M323.D57 gauging pin is intended for end‑dimension checks and go/no‑go inspection in workshop and production settings where a single, clearly defined reference diameter is required. Is the diameter tolerance suitable for precision assemblies? Yes, the ±0.002 mm accuracy of the inspection pin meets the demands of tightened assembly tolerances and provides reproducible results for serial inspection. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen to provide resistance to routine wear in workshop applications while maintaining dimensional stability. Does the product include protective packaging? The gauging pin is supplied as a single item and is delivered in a transport case to protect the gauge during storage and transport. How can the M323.D57 be identified in stock systems? Identification is via SKU M323.D57 and GTIN 4061905067952, simplifying inventory control and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.58mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise bore verification thanks to the combination of a 13.58 mm nominal diameter, tight ±0.002 mm tolerance and a 50 mm length in a robust workshop design; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D58 — 13.58 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.D58 for precise checking of bores and fits in workshop and inspection environments. Diameter 13.58 mm precision check Dimensional tolerance ±0.002 mm 50 mm overall length for deeper bores Workshop version with protective transport box Consistent accuracy for fewer rejects and faster inspection This single test pin is manufactured for repeatable dimensional checks where reliable tolerance control matters. With a nominal diameter of 13.58 mm and a verified positional variation of ±0.002 mm, the pin supports tight go/no‑go decisions on fits and clearances. The combination of exact nominal size and low variation reduces measurement uncertainty, helping to lower scrap rates and shorten inspection cycles — a clear efficiency benefit for production and quality control. The instrument’s compact length is suited to component bores and fixtures where controlled insertion depth is required. Built for the workshop — durable handling and safe transport Designed as a workshop execution, the pin is made from special steel, giving a balance of mechanical integrity and handling robustness appropriate for everyday use at the bench or on the shop floor. Supplied as a single item with a protective transport box, the pin is easy to store and carry without risking damage in transit. The modest mass facilitates quick manual handling during repetitive checking tasks and integration into inspection jigs or assembly stations, preserving throughput without compromising on measurement stability. Simple integration into quality workflows and supplier assurance The test pin is suitable for routine verification tasks and set‑up checks in batches or fixtures, providing a straightforward physical reference that complements electronic measurement systems. The clear identification (SKU M323.D58, GTIN 4061905067969) and the workshop specification simplify procurement and inventory management. Metav’s role as a precision partner, with a broad catalogue and logistics base in Emmerich, ensures reliable supply and supportive consultancy when matching measuring hardware to particular process requirements. Contact Metav Werkzeuge for tailored advice on integrating this gauge pin into inspection routines and for delivery directly from our Emmerich quality hub Technical data SKU: M323.D58 GTIN: 4061905067969 Label: Prüfstift, einzeln, 13,58 mm Länge 50 mm Manufacturer brand: Metav IndustryLine Weight: 0.1 kg Core specifications Nominal diameter: 13.58 mm Length: 50 mm Dimensional variation: ±0.002 mm Special features Workshop version Delivered in protective transport box Material: Special steel Single test pin FAQ What nominal diameter does the pin have? The gauge pin M323.D58 has a nominal diameter of 13.58 mm. What tolerance is achieved with this test pin? The workshop pin from Metav IndustryLine is specified with a dimensional variation of ±0.002 mm. What material is used for the pin? The pin is made from special steel, supplied as a single test pin (SKU M323.D58). How is the pin supplied for transport and storage? Delivery is in a protective transport box to prevent damage during handling and transit. Can this pin be used in inspection fixtures and jigs? Yes, the 50 mm length and precise diameter make it suitable for use as a reference or checking element in fixtures and inspection setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.59mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise small‑diameter gauging combined with rugged workshop design and reliable transport protection; the compact gauge pin streamlines end‑dimension checks and reduces inspection rework. Order the item directly via Metav Werkzeuge or consult our specialists for application advice. Test pin M323.D59 — Gauge pin, 13.59 mm diameter, 50 mm length (Metav IndustryLine) A Test pin M323.D59 designed for precise end‑dimension verification and use in workshop jigs and inspection fixtures. Workshop version for industrial use Tolerance ±0.002 mm for fine repeatability Diameter 13.59 mm, length 50 mm Precision where small differences matter The compact gauge pin delivers high precision for measurement tasks in which millimetre fractions decide accept/reject outcomes. With a nominal diameter of 13.59 mm and a declared accuracy of ±0.002 mm, this pin is classified for the micro measurement range suitable for fine mechanical work; that classification reflects the balance between minimal probe deflection and the reach required for typical small components. The immediate benefit is faster, reproducible inspection: fewer ambiguous readings, fewer rework cycles and a clearer quality record for serial checks. Built to withstand workshop routines Manufactured from special steel and specified as a workshop version, the pin combines corrosion‑resistant durability with dimensional stability under frequent handling. A 50 mm shaft length provides sufficient engagement for end‑dimension checks while remaining easy to seat in chimed holders or simple fixtures. Supplied in a transport case, the component arrives protected against knocks and contamination, reducing the time needed to prepare inspection tools and preserving the pin’s metrological condition between uses. Practical integration in inspection setups The gauge pin is intended for end‑dimension and positional checking in jigs, go/no‑go fixtures and single‑point inspection tools. Its compact form factor supports quick replacement and low‑effort alignment in series testing, which increases throughput in repetitive QA tasks. Where traceable calibration is required, the listing does not include a calibration certificate; nevertheless, the pin’s combination of nominal diameter and fine tolerance makes it a reliable reference element for shop‑floor control and batch sampling processes. For workshop‑grade, small‑diameter gauging rely on Metav IndustryLine’s test pin M323.D59 — contact Metav Werkzeuge for availability and supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: M323.D59 GTIN: 4061905067976 Manufacturer: Metav IndustryLine Weight: 0.1 kg Facts Diameter: 13.59 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Material: Special steel Special features Workshop version Supplied in transport case for protection Intended use: end‑dimension checks Measurement category: Micro (10–100 mm range) FAQ What tolerance does the gauge pin offer? The Test pin M323.D59 (Metav IndustryLine) is specified with a tolerance of ±0.002 mm, suitable for fine workshop inspections. Is the pin supplied ready for transport and storage? The item is delivered in a transport case to protect the gauge pin during handling and transit. Which applications suit this pin best? Its design targets end‑dimension verification, quick go/no‑go fixtures and small‑component checks in workshop and production environments. What material is used for the pin and how does it behave under use? The gauge pin is made from special steel, selected for dimensional stability and resistance to everyday workshop influences. Is a calibration certificate included with the product? The product listing does not include a calibration certificate; the standard delivery comprises the gauge pin and transport case. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.5mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of high-precision tolerance (±0.002 mm), 13.5 mm diameter and robust special-steel construction for repeatable go/no-go checks on workshop gauges; supplied as a workshop-grade part with transport case for safe handling — order or consult Metav Werkzeuge for application advice. Gauge pin, single, Ø13.5 mm, length 50 mm (M323.D50) — Metav IndustryLine Gauge pin M323.D50 is a single plug gauge pin designed for end‑limit checks and precise reference measurements in jigs and fixtures High-precision tolerance ±0.002 mm Diameter 13.5 mm, length 50 mm Special-steel construction Workshop version, transport case included Precision that reduces rework and inspection time For repetitive dimensional checks the primary benefit is predictable accuracy: the pin’s tolerance of ±0.002 mm minimises ambiguity in pass/fail tasks and reduces downstream rework. Compact and purpose-built for workshop use, the solid cylindrical design provides a stable reference that integrates easily into measuring fixtures and checking assemblies. The tight tolerance translates directly into fewer ambiguous decisions on the shop floor, which improves throughput in batch inspections and speeds routine quality gates without adding complexity to existing processes. Robust material and handling for heavy use Constructed from special steel, this gauge pin resists wear and maintains form under frequent insertion cycles, extending service life compared with untreated pins. The workshop version specification means the finish and hardening balance durability with practical handling; the result is a component that performs consistently in demanding environments. Supplied in a transport case, the pin arrives protected from damage in transit and is ready for immediate use or secure storage between shifts, preserving calibration and minimising downtime for replacements. Practical application and compatibility with inspection workflows Engineered as a simple, reliable reference for go/no‑go checks and alignment tasks, the single gauge pin matches common workshop routines where end‑measurements and fitting checks are required. The cylindrical form and standard diameter make it straightforward to pair with bore gauges, alignment fixtures or comparator setups. Marked with the SKU M323.D50, the component suits production and maintenance environments where small, repeatable gauges are used to confirm assembly tolerances or to check tooling runs quickly without elaborate setup. Contact Metav Werkzeuge for tailored advice and secure immediate supply of the M323.D50 gauge pin for your inspection tasks Technical Data Article number: M323.D50 GTIN: 4061905066290 Material: Special steel Diameter: 13.5 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Facts Category: Gauge pins Single, plain cylindrical design Workshop-grade finish Transport case for delivery Special features Suitable for fixture and jig checks Durable against repeated insertion cycles Compact for easy storage and handling SKU marking for inventory control FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, providing high repeatability for go/no‑go checks and reference measurements in workshop applications. Which materials is the pin suitable for checking? As a dimensional reference, the pin itself is made from special steel; it is intended for use in verifying bores, seats and alignment features across typical metallic components. Is the M323.D50 ready for immediate use upon delivery? Yes, the M323.D50 is supplied as a workshop version and arrives in a transport case, protected for immediate deployment or safe storage without additional packaging work. How does the M323.D50 support production efficiency? By offering a compact, precisely made reference with a tight tolerance, the pin reduces ambiguity in inspection steps, speeds routine checks and lowers the risk of rework in serial production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.61mm Gauge Pin, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop-grade robustness, ±0.002 mm verification accuracy and a compact 13.61 mm reference diameter for repeatable go/no‑go checks; order the gauge pin directly via Metav Werkzeuge or request guidance from our consultants. Gauge pin M323.D61 — single gauge pin, 13.61 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.D61 is a single reference pin designed for precise fit checks and dimensional verification in workshop and inspection environments Workshop-grade construction for daily use Diameter 13.61 mm for precision fits Length 50 mm with robust special steel Tolerance ±0.002 mm for tight verification Precise verification that speeds approval processes The compact reference diameter and tight tolerance make this pin a reliable instrument for repeatable acceptance checks. With a nominal diameter of 13.61 mm and a verified tolerance of ±0.002 mm, the component supports decisive go/no‑go evaluations and reduces measurement uncertainty during routine inspections. This direct performance data helps to shorten decision loops in quality control and to maintain consistent assembly tolerances across batches. Workshop-ready build for frequent handling Built as a workshop version, the pin is manufactured from special steel and configured for everyday use where robustness and handling matter. The 50 mm length provides secure engagement with small assemblies while keeping the tool compact for rapid exchange on benches. Supplied ready for transport in a protective case, the item is dimensionally stable and simple to store between shifts, supporting continuous operation without time‑consuming setup. Designed for small-part inspection and precision fits Classified in the micro range (measurement span around 10–100 mm), this reference pin is suitable for fine mechanical tasks such as connector seating checks, small bearing trials and precision mating tests. Its compact geometry combines stiffness with accessibility for confined spaces, making it well suited to inspection benches, jig stations and final acceptance routines. The combination of material choice and dimensional accuracy supports reliable checks that integrate directly into standard workshop workflows. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to secure the M323.D61 and discuss application suitability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.D61 GTIN: 4061905067990 Material: Special steel Diameter: 13.61 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Delivery: Transport case included Facts Nominal diameter: 13.61 mm Measurement range: 13.61 mm Length: 50 mm Weight: 0.1 kg Resolution / accuracy class: ±0.002 mm Special features Workshop version Robust special steel construction Compact geometry for small components SKU: M323.D61 FAQ What is the intended use for this gauge pin? The gauge pin M323.D61 is intended for fit checks, go/no‑go verification and dimensional confirmation of small components in workshop and inspection settings. Is the material corrosion‑resistant? The pin is made from special steel; specific corrosion properties depend on the alloy treatment and environment, so storage in the supplied protective case is recommended. How precise is the pin for dimensional checks? The pin is manufactured to a tolerance of ±0.002 mm, making it suitable for tight verification tolerances in quality control. Can this gauge pin be used in confined assemblies? Yes. The 50 mm length and compact diameter are designed to access confined areas and to support checks on small assemblies and connectors. Does the product come with a transport or storage solution? The M323.D61 is supplied with a protective transport case to simplify handling and safe storage between uses. Is this part suitable for serial inspection workflows? Yes. The workshop design and repeatable dimensional accuracy make the pin appropriate for serial inspection and routine quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.62mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact 13.62 mm diameter and a 50 mm length in a rugged workshop version, manufactured from special steel and finished to a tight ±0.002 mm tolerance; the result is a reliable gauge pin that keeps inspection cycles short and rejects low. Order the test pin directly via Metav Werkzeuge or contact our consultants for specification checks. Test pin M323.D62 — workshop test pin, Ø 13.62 mm, 50 mm length Test pin M323.D62 for end‑dimension checks and fixture gauging in workshop and inspection environments. Workshop version, robust design Diameter 13.62 mm for precise gauging Length 50 mm for standard fixtures Tolerance ±0.002 mm ensures tight accuracy Reliable accuracy for daily inspection tasks A compact gauge pin that prioritises precision for routine measurement work: the diameter of 13.62 mm and the manufacturing tolerance of ±0.002 mm deliver reproducible results when inspecting end dimensions or confirming fit within assemblies. Machined from special steel, the component resists wear and maintains contact geometry over repeated cycles, which reduces the need for frequent replacements and supports a steady quality flow on the shop floor. Compact design for fixture and gauge compatibility The moderate 50 mm length and standard diameter make this measuring pin suitable for common jigs, plug gauges and handheld verification tools; it slips into existing set‑ups without custom adapters. The workshop version is optimised for handling and resilience rather than delicate laboratory storage, and the item is supplied in a protective transport box to safeguard the measuring face during transit. Such packaging helps preserve the pin’s geometry until the moment of use. Integration into efficient workshop routines Built for fast repeatability, the gauge pin reduces adjustment time and simplifies go/no‑go checks in production and maintenance workflows. As part of the Metav IndustryLine range, the component benefits from a robust supply chain and consistent quality control, which supports predictable stock and fast replenishment when instruments wear. Technical teams benefit from a low‑complexity replacement policy and straightforward interchangeability with matching fixtures and gauges. For workshop-ready precision from Metav IndustryLine, request availability and tailored advice from Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.D62 GTIN: 4061905068003 Manufacturer: Metav IndustryLine Facts Diameter: 13.62 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Supplied in transport box Intended for end-dimension checks and gauging FAQ What tolerance does the test pin offer? The test pin is manufactured to a tolerance of ±0.002 mm, providing the close dimensional control required for workshop gauging. Which material is used for this gauge pin? This gauge pin is made from special steel to ensure wear resistance and long service life in routine inspection tasks. What are the main applications for this measuring pin? The measuring pin is intended for end‑dimension checks, fixture verification and plug gauge applications in production and maintenance. Is the pin compatible with standard fixtures? The 13.62 mm diameter and 50 mm length were chosen for compatibility with common fixtures and gauges, allowing simple integration into existing setups. How is the item packaged for delivery? The pin is supplied protected in a transport box to preserve the measuring faces during storage and shipment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.63mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop-ready robustness, traceable precision and compact handling to speed up inspection routines and reduce rework; order the gauge pin directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Gauge pin M323.D63 – Ø 13.63 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.D63 is a single precision test pin intended for end-dimension checks and hole gauging in workshop and metrology settings. Precision tolerance ±0.002 mm Diameter Ø 13.63 mm for accurate gauging Hardened special-steel construction Precision that keeps production moving The gauge pin is manufactured for precision inspection tasks where repeatable results matter. With a specified tolerance of ±0.002 mm, the pin supports fine dimensional checks that reduce the risk of rejected parts or costly rework. The nominal diameter Ø 13.63 mm matches common hole sizes, enabling straightforward verification of bores and plug fits. For operators and quality engineers, the measurable benefit is lower scrap rates and faster go/no-go decisions thanks to consistently narrow uncertainty margins. Workshop-ready design for practical use Designed as a single test pin for hands-on inspection, this tool combines a 50 mm length with a compact form that is easy to handle and position in production environments. The special steel construction provides wear resistance and dimensional stability during repeated use, so calibration intervals can be extended compared with softer materials. The workshop version is optimised for routine checks on assemblies and components, helping technicians complete verification steps quickly without compromising on accuracy. Seamless fit into quality workflows The M323.D63 integrates simply into established inspection procedures and jigs, making it suitable for incoming inspection, in-process checks and final dimensional control. Supplied as a single, labelled pin, it supports traceable measurements when recorded in inspection logs and contributes to a consistent quality culture on the shop floor. Sourcing from Metav IndustryLine ensures access to a wide range of complementary measurement aids and fast replenishment from Metav Werkzeuge, shortening procurement cycles and keeping production lines supplied. Choose Metav IndustryLine gauge pins via Metav Werkzeuge for traceable precision and straightforward supply — contact Metav Werkzeuge for technical advice or to request the gauge pin M323.D63 Technical Data Article number: M323.D63 GTIN: 4061905068010 Brand: Metav IndustryLine Numbers / Core technical data Diameter: 13.63 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features / Design Single test pin Workshop design Material: special steel Application: end-dimension checks, hole gauging FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.D63 is specified with a tolerance of ±0.002 mm, suitable for precision inspection tasks requiring close dimensional control. Which materials is the pin suitable for checking? As a measurement artefact, the pin itself is made of special steel and is used to inspect holes and fits in a wide range of component materials; the pin verifies dimensions rather than cutting or shaping materials. Is the gauge pin supplied individually or as a set? This article is supplied as a single test pin (single unit) and is intended for direct use in inspection routines or as a reference piece. Can the pin be used for plug-fitting tests and go/no-go checks? Yes, the gauge pin is suitable for plug-fitting checks and for use within go/no-go procedures when incorporated into the appropriate inspection jigs. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.64mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of high dimensional accuracy (±0.002 mm), workshop‑grade design, and protected delivery in a transport case for dependable inspection results; order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.D64 — Precision gauge pin, Ø 13.64 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.D64 is a single precision checking pin intended for dimensional inspection and end‑measure verification in workshop and quality‑control environments Workshop-grade design for robust use Diameter 13.64 mm with ±0.002 mm accuracy Length 50 mm for end‑measure verification Precision where repeatability matters A compact measuring reference, this checking pin delivers ±0.002 mm dimensional accuracy, which supports tight tolerance control during fit and end‑measure checks. The defined diameter of 13.64 mm provides a stable datum for quick go/no‑go assessments and reference comparisons on production benches. By using a fixed‑size reference pin, measurement variability is reduced and inspection throughput is increased, enabling faster decision making in production control without compromising traceability. Built for the workshop — robust and reliable Manufactured from special steel, the pin is offered in a workshop‑grade execution that balances durability with dimensional stability. The 50 mm shank provides sufficient engagement for end‑measure tasks while remaining easy to handle during repetitive checks. Delivered individually and protected for transport, the component is ready for immediate use in inspection fixtures or hand‑held verification routines, ensuring low downtime between setup and measurement. Practical application and efficiency gains The test pin performs as a reliable reference for manual inspection, fixture verification and rapid fit trials in assembly or maintenance workflows. Its single‑piece design simplifies inventory and replacement logic, while the narrow tolerance reduces the need for repeat measurements and rework. For operations seeking to streamline quality checks, the pin offers a practical combination of precision, robustness, and straightforward integration into existing inspection zones. For precision end‑measure verification, specify the Metav IndustryLine gauge pin M323.D64 through Metav Werkzeuge — contact our Emmerich team for product matching and delivery options Technical Data Article number: M323.D64 GTIN: 4061905068997 Brand: Metav IndustryLine Facts Diameter: 13.64 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Delivered in transport case Single checking pin FAQ What tolerance can be expected from this gauge pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, making the Metav IndustryLine M323.D64 suitable for precise end‑measure verification. Which materials is the pin made from? This test pin is produced from special steel, offering a balance of dimensional stability and workshop durability. How is the pin supplied for transport and storage? The M323.D64 is delivered individually and protected in a transport case to prevent damage during handling and transit. What typical tasks is the pin suited for in quality control? The checking pin is intended for dimensional inspection, fit trials and end‑measure checks on production benches and fixtures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.65mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of tight dimensional control with a 13.65 mm diameter test pin manufactured in special steel and finished to a ±0.002 mm tolerance; the compact 50 mm length makes it ideal for routine end‑measure verification. Order the item directly via Metav Werkzeuge or ask our consultants for application advice. M323.D65 gauge pin — 13.65 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.D65 for precise end‑measurement checks and workshop inspection tasks Workshop‑grade design Ø 13.65 mm nominal 50 mm overall length Tolerance ±0.002 mm Precision where small tolerances matter The compact test pin delivers repeatable dimensional checks for end‑measure verification, combining a 13.65 mm nominal diameter with a certified ±0.002 mm tolerance. Such specification supports efficient quality control by reducing rework and lowering measurement uncertainty during pass/fail assessments. The tight tolerance is particularly useful for short production runs or in‑process inspection where small deviations have immediate downstream effects, enabling faster decision‑making and more consistent part acceptance rates. Durable construction for everyday workshop use Manufactured from special steel and executed for workshop conditions, this single test pin balances stiffness and handling convenience in a 50 mm overall length. The material choice provides wear resistance during repeated seating in fixture bores and maintains surface integrity over numerous inspection cycles. At approximately 0.1 kg, the pin is easy to position in gauges and jigs while offering the mass needed for stable contact during verification tasks, minimising measurement error caused by movement. Designed for straightforward integration into inspection routines The compact format and clear identification make the product simple to incorporate into existing inspection benches and fixture systems. Traceability is supported through the SKU and GTIN, aiding inventory control and audit trails within production quality workflows. The pin is supplied as a single unit intended for end‑measure checks and is particularly suited to workshops that require reliable, repeatable small‑diameter verification without complex handling or calibration regimes. For workshop‑ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and supply via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: M323.D65 GTIN: 4061905069000 Label: Gauge pin, single, 13.65 mm, length 50 mm Facts Diameter: 13.65 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Single test pin for end‑measure verification High‑precision finishing FAQ What tolerance does this gauge pin provide? The Metav IndustryLine M323.D65 gauge pin is finished to a ±0.002 mm tolerance, suitable for tight end‑measure verification tasks. What material is the pin made from? The pin is manufactured from special steel, chosen for wear resistance and suitability for frequent use in workshop inspection. Which tasks is this pin best suited for? This compact gauge pin is intended for end‑measurement checks, final size verification and plug‑type inspections in workshop and small‑series production. Can the pin be used in standard fixture gauges and test benches? Yes, the 50 mm overall length and 13.65 mm diameter make the pin compatible with common fixture setups and bench gauges designed for short‑range verification. How is the item identified for procurement and traceability? Identification is via SKU M323.D65 and GTIN 4061905069000 for stock control and audit purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.66mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of precise dimensional control and robust workshop design: the combination of ±0.002 mm tolerance and special steel construction ensures reliable end‑measure checks with low rework rates. Order the gauge pin directly via Metav Werkzeuge or request advice from our consultants for specification matching. Gauge pin M323.D66 — Test pin, 13.66 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.D66 is a precision test pin designed for accurate dimensional verification and alignment tasks in workshop environments, offering a compact format for micro components and inspection fixtures. Workshop version for robust everyday use Diameter 13.66 mm, length 50 mm Tolerance ±0.002 mm for high precision Supplied in protective transport box Precise micro-range performance for small parts Designed for measurements within the micro class, this test pin fits the profile of compact inspection tools used where repeatability and small footprint matter. With a nominal diameter of 13.66 mm and a working length of 50 mm, the component is suited to fine‑mechanical applications and end‑dimension verification. The stated ±0.002 mm tolerance reflects a tight manufacturing specification that reduces uncertainty in assembly checks and bore gauging. For quality control workflows, the narrow tolerance helps distinguish acceptable parts from those requiring rework, speeding decision cycles in production. Robust workshop construction for daily use The workshop version is engineered for routine handling and rapid integration into inspection jigs. Manufactured from special steel, the pin withstands frequent contact and offers dimensional stability under normal workshop conditions. Supplied in a protective transport box, the item arrives ready for secure storage and safe transport between stations. The compact mass and ergonomics enable quick manual positioning while maintaining the stiffness necessary for reproducible measurements during alignment and go/no‑go assessments. Practical application, handling and benefits As a dedicated test pin for end‑measure checks, the component simplifies tasks such as bore gauging, alignment dowelling and reference setting on fixtures. The combination of compact geometry and high repeatability improves measurement throughput and lowers the risk of false rejects. Routine handling tips include keeping contact surfaces clean and using gentle seating force to preserve the repeatability of the measurement. The product’s standard format makes it straightforward to integrate into inspection routines and replace within modular gauge assemblies where interchangeability is required. For reliable workshop inspection from our Emmerich quality centre, contact Metav Werkzeuge to request the Metav IndustryLine gauge pin M323.D66 or technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.D66 GTIN: 4061905069017 Material: Special steel Length: 50 mm Diameter: 13.66 mm Tolerance: ±0.002 mm Weight: 0.1 kg Version: Workshop execution Delivery: Protective transport box Facts Length: 50 mm Diameter: 13.66 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Protective transport box Category: Gauge pins Application: End‑measure checks FAQ What applications is this gauge pin suited for? This gauge pin is intended for dimensional verification, bore gauging and alignment tasks; the M323.D66 from Metav IndustryLine is particularly useful for end‑measure checks on small to medium components. How precise is the measurement standard of the pin? The test pin is manufactured to a tolerance of ±0.002 mm, providing a high level of precision suitable for tight inspection criteria and reproducible reference measurements. Is the pin delivered ready for use and how is it packaged? The item is supplied in a protective transport box and delivered as a workshop version ready for immediate integration into inspection workflows. What material is used and how does it affect durability? Made from special steel, the pin combines dimensional stability with resistance to routine wear, supporting frequent handling in workshop environments. Can the pin be used as a reference in fixture assemblies? Yes; the standardised diameter and tight tolerance make the pin suitable as a reference dowel or locating element within modular fixtures and gauge assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.67mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop robustness, tight diameter tolerance and compact length for reliable end‑dimension checks and quick fixture set‑up; order the item directly via Metav Werkzeuge or consult the team for application advice. M323.D67 gauge pin — workshop version, Ø 13.67 mm, 50 mm length (Metav IndustryLine) The M323.D67 gauge pin is a single plug gauge designed for precise end‑dimension verification and fixture alignment in workshop metrology. Workshop version for robust everyday use Diameter precisely ground to 13.67 mm Length 50 mm for compact checking tasks Tight tolerance ±0.002 mm ensures repeatability Precision for end‑dimension verification The M323.D67 from Metav IndustryLine is manufactured for applications where small deviations matter: the 13.67 mm diameter with a declared tolerance of ±0.002 mm provides consistent results when checking end‑masses, seating positions or locating holes. Made from special steel, the gauge pin combines wear resistance with stable dimensional behaviour, so measurements remain reproducible across inspection cycles. This level of control reduces rework and shortens set‑up time on jigs and fixtures. Robust handling and workshop suitability Designed as a workshop version, the test pin balances stiffness and handling for daily use. At a compact 50 mm length and an approximate weight of 0.1 kg, the pin is easy to manoeuvre during assembly checks and bench inspections while maintaining the necessary rigidity for accurate placement. The surface finish and material selection limit fretting and preserve the ground diameter, supporting repeatable seating and minimising measurement drift over time. Practical integration into inspection workflows The pin serves as a dependable reference in go/no‑go sequences, fixture positioning and comparative checks. As a single, individually supplied plug gauge it is suitable for rapid verification tasks and for inclusion in gauge sets. Clear dimensional data and a precise tolerance make it straightforward to document inspection results and to trace measurement deviations back to process steps, improving both quality assurance and throughput in small‑batch or serial production environments. For workshop‑grade precision and specification advice, contact Metav Werkzeuge for availability and tailored application guidance regarding the Metav IndustryLine M323.D67 gauge pin Technical data Article number: M323.D67 GTIN: 4061905069024 Manufacturer: Metav IndustryLine Material: Special steel Facts Diameter: 13.67 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Single test pin (individual delivery) Intended for end‑dimension checks and fixture alignment FAQ What tolerance does the gauge pin offer? The M323.D67 gauge pin is specified with a tolerance of ±0.002 mm for high repeatability in end‑dimension checks. Which material is used for this plug gauge? The plug gauge is made from special steel, chosen for wear resistance and stable dimensional behaviour under workshop conditions. Is the M323.D67 suitable for fixture alignment? Yes, the M323.D67 gauge pin is intended for fixture alignment and quick go/no‑go verification due to its compact 50 mm length and precise diameter. How is the gauge pin delivered? The product is supplied as a single item (individual test pin) suitable for immediate inclusion in inspection routines. Can the pin be used for serial production checks? The tight tolerance and workshop design of the M323.D67 make it well suited to repetitive checks in small‑batch and serial production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.68mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise diameter control and robust workshop construction to keep inspections consistent and rework rates low; the compact format and tight manufacturing tolerance ensure reliable end‑dimension verification — order directly via Metav Werkzeuge or consult our specialists for application matching. Gauge pin M323.D68 — 13.68 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.D68 is a single precision reference pin designed for fast end‑dimension checks and assembly verification in inspection and workshop environments. Precision diameter 13.68 mm Length 50 mm for compact checks Manufacturing tolerance ±0.002 mm Made from special steel workshop grade Assured dimensional accuracy to reduce rejects and rework The compact gauge pin delivers a reliably machined 13.68 mm diameter with a tight production tolerance of ±0.002 mm, providing a measurable improvement in repeatability for everyday inspection tasks. By using a defined reference pin rather than subjective visual gauging, process control becomes demonstrably more effective: measurement deviation sources are reduced and non‑conforming parts are identified earlier, which supports lean production and lowers downstream correction costs. Durable construction for repeated workshop use Constructed from Special steel and finished for workshop environments, this reference pin combines wear resistance with easy handling in short‑reach checks. The 50 mm length balances stiffness and accessibility for common plug checks, enabling single‑hand operation on benches and inspection stations. The workshop version is optimised for everyday use, resisting abrasion from frequent insertion into bores and providing consistent contact geometry throughout its service life. Traceable identification and simple stock integration Designed as an individual inspection tool, the pin is supplied with clear identification for inventory control: GTIN 4061905069031 and SKU M323.D68 ensure fast reordering and unambiguous traceability in quality documentation. As a compact reference for end‑dimension verification, this component fits into standard inspection routines and complements plug‑gauge sets or comparative checks, helping to document conformity within production records and audit trails. For reliable end‑dimension control in the workshop, request the Metav IndustryLine gauge pin M323.D68 via Metav Werkzeuge or speak with our consultants in Emmerich to confirm suitability for specific inspection tasks Technical data Article number: M323.D68 GTIN: 4061905069031 Category: Messstifte Facts Diameter: 13.68 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Supplied individually Precision manufacturing FAQ What tolerance does this gauge pin offer? The M323.D68 gauge pin is manufactured to a tolerance of ±0.002 mm, allowing it to serve as a reliable reference for precise end‑dimension checks. Is the material suitable for frequent use in a workshop? Yes, the M323.D68 is made from special steel in a workshop configuration, offering wear resistance appropriate for regular insertion and removal. Can this pin be used in documentation and stock systems? The gauge pin carries clear identifiers — GTIN 4061905069031 and SKU M323.D68 — to simplify traceability and replenishment in inventory systems. Is the pin supplied individually or as part of a set? This item is supplied as an individual gauge pin, designed for targeted end‑dimension verification rather than as a set component. Which applications benefit most from this type of gauge pin? Typical uses include bore verification, assembly checking and incoming inspection where a compact, accurate reference is needed for end‑dimension control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.69mm Gauge Pin, 50mm Length, Workshop Version - Metav IndustryLine
Precise workshop-grade gauge pin with a 13.69 mm diameter and 50 mm length, offering a measurement tolerance of ±0.002 mm for repeatable locating and end-measure checks; its special steel construction increases wear resistance in daily use. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.D69 — 13.69 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.D69 designed for accurate end-measure verification, alignment and fixture locating in workshop inspection and toolmaking applications Workshop version for robust shop use Diameter 13.69 mm, precision ±0.002 mm 50 mm effective length for reliable locating Made from special steel for long service life Precision that makes routine checks dependable The inspection pin combines a finely controlled diameter of 13.69 mm with a verified tolerance of ±0.002 mm, providing the dimensional stability required for repeatable processes. In practical terms, this level of accuracy reduces rework and speeds up set‑up because measurement variation is minimised; where alignment or end‑measure checks are frequent, consistent pin dimensions translate into fewer adjustments and a steadier production flow. The tight tolerance is particularly beneficial when used as a reference or locating datum in jigs and fixtures, where small geometric deviations can otherwise accumulate. Built for daily workshop demands As a workshop execution item, the pin is manufactured from special steel, chosen for a balance of toughness and wear resistance to withstand repeated insertions and withdrawal in hardened bores or locating holes. The 50 mm length provides sufficient engagement for stable locating while remaining compact enough for easy handling. Delivered in a transport case to protect the surface finish during storage and movement, the component’s construction focuses on longevity and low-maintenance operation, which supports continuous shop-floor use without frequent replacement. Practical use and compatibility in inspection workflows The pin serves multiple metrology tasks: use as a locating element for fixture set‑up, as a reference for plug checks, and for alignment during assembly operations. The compact geometry makes the part suitable for machine-shop inspection benches as well as toolroom jigs. Because the component is a standard workshop gauge pin, it integrates smoothly into existing measurement routines and fixture geometries; traceable dimensioning and consistent form give staff confidence in go/no‑go assessments and in-process checks, supporting faster decision-making and less downtime. For a tailored parts recommendation or technical clarification from Metav Werkzeuge in Emmerich, request a quotation or specification check via email or phone to ensure the M323.D69 suits the intended inspection task Technical data Article number: M323.D69 GTIN: 4061905069048 Label: Prüfstift, einzeln, 13,69 mm Länge 50 mm Facts Diameter: 13.69 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Delivered in a transport case SKU: M323.D69 FAQ What is the dimensional tolerance of this gauge pin? The gauge pin M323.D69 is specified with a tolerance of ±0.002 mm, ensuring high repeatability for locating and end-measure tasks. Which material is used for the pin? The M323.D69 is made from special steel, selected for a durable surface and resistance to wear under frequent use. Is the pin suitable for fixture locating and alignment? Yes, this inspection pin is intended for locating, alignment and end-measure verification in workshop and toolmaking fixtures. Does the product come with protection for transport? Delivery of the M323.D69 is in a transport case to safeguard the finished surface during storage and movement. Can the gauge pin be used in hardened bores or precision holes? The gauge pin M323.D69 is suitable for use in precision holes and hardened locating bores where tight dimensional stability is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.6mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Combine ±0.002 mm repeatability with a 13.6 mm ground diameter and 50 mm hardened length for consistent end‑dimension checks; order the inspection pin directly via Metav Werkzeuge or consult our specialists for application guidance. Inspection pin M323.D60 — gauge pin, 13.6 mm diameter, 50 mm length (Metav IndustryLine) The Inspection Pin M323.D60 is a single gauge pin designed for precise end‑dimension verification in workshop and inspection settings ±0.002 mm tolerance for high repeatability 13.6 mm ground diameter for precise fits 50 mm hardened shaft for stable probing Workshop execution in special steel material Accuracy that reduces rework and inspection time The pin offers a ±0.002 mm tolerance, which translates into reliable repeatability for serial checks and incoming inspection tasks. Such a tight specification minimises ambiguous pass/fail results and helps to reduce downstream rework and scrap rates. In practical terms, high repeatability shortens inspection cycles because fewer cross‑checks are required; this benefits production throughput while maintaining quality control standards. The precision finish on the measuring surface supports consistent seating in gauges and jigs, ensuring that measurement uncertainty stays low even under frequent use. Compact gauge for precise micro‑range measurements Classified in the micro range (measurement span 10–100 mm), this compact gauge pin is optimised for small components and tight tolerance fits. The 13.6 mm diameter and 50 mm length make it suitable for bores, bushings and mating features where a stable reference diameter is required. The small form factor eases handling in dense assemblies and fixture checks, while the ground surface finish ensures accurate engagement with mating parts. The device is particularly useful where dimensional checks must be repeatable across many parts, providing a simple physical reference that complements dimensional measuring systems and reduces interpretation time. Durable, workshop‑grade construction for everyday metrology Manufactured in special steel with a hardened shaft, the pin balances wear resistance with geometric stability for routine workshop use. The workshop execution designation indicates robustness in surface treatment and handling tolerances tailored to industrial environments. The modest weight and solid construction support stable probing and resistance to accidental deformation, preserving the specified tolerance during standard handling and storage. As a basic but critical tool in the gauge set, this pin provides a dependable mechanical reference that integrates with inspection benches, plug gauge sets and functional test fixtures. Contact Metav Werkzeuge today to specify the right gauge pin for inspection tasks or to discuss compatibility with existing gauge sets; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.D60 GTIN: 4061905067983 Manufacturer: Metav IndustryLine Facts Diameter: 13.6 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pin (Messstifte) FAQ What nominal diameter does this gauge pin have? The gauge pin has a nominal diameter of 13.6 mm and is supplied as the single inspection pin M323.D60 for dimensional reference. What level of repeatability can be expected? Repeatability is specified at ±0.002 mm, enabling consistent comparative checks and reducing ambiguous inspection results with the Metav IndustryLine inspection pin. For which applications is this pin best suited? This pin is intended for end‑dimension checks in workshops, fixture verification and plug‑fit testing of bores and mating features where micro‑range accuracy is required. What material and construction define its durability? The pin is made from special steel in a workshop‑grade execution with a hardened shaft to resist wear and maintain geometric stability during routine use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.71mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Compact workshop-grade gauge pin precision and rugged construction combine to deliver reliable dimensional checks: 13.71 mm diameter with a manufacturing tolerance of ±0.002 mm, made from special steel and supplied ready for workshop use; order the component directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.D71 — 13.71 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.D71 is a single workshop-grade test pin for fast, repeatable dimensional checks in machining, fixture set‑up and quality inspection. Workshop-grade construction Precision ±0.002 mm Diameter 13.71 mm Length 50 mm single pin Accurate checks for production and inspection Designed for straightforward dimensional verification, the gauge pin delivers precision where repeatability matters. The specified manufacturing tolerance of ±0.002 mm ensures that the pin is suitable for tight control tasks in machine shops and jig set‑ups, providing a clear numerical basis for pass/fail decisions. Using a defined-diameter reference such as 13.71 mm reduces interpretation effort during in-line checks and supports efficient process control. Robust build for everyday workshop use Built in a workshop version and manufactured from special steel, this test pin tolerates regular handling and contact with typical workshop environments. The robust material choice provides wear resistance for frequent seating and withdrawal operations; as a result, inspection intervals are extended and tool turnover is reduced. Supplied in a protective transport case, the single pin remains secure during storage and transit, helping to keep the dimensionally critical surface free from nicks or contamination. Practical handling and integration into workflows At 50 mm overall length and approximately 0.1 kg in mass, the pin is compact enough for manual use yet long enough for stable engagement in most fixtures. The single‑piece design suits uses where a dedicated reference pin is required — for locating bores, checking plug fits or setting up mandrels. Supplied under the Metav IndustryLine label (SKU M323.D71), the component benefits from Metav’s logistics and quality filter based in Emmerich, providing reliable supply and straightforward reordering for ongoing production needs. Contact Metav Werkzeuge for a targeted recommendation on how the Metav IndustryLine 13.71 mm gauge pin fits specific inspection routines, or request technical details via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.D71 GTIN: 4061905069789 Brand: Metav IndustryLine Material: Special steel Weight: 0.1 kg Core dimensions Diameter: 13.71 mm Length: 50 mm Manufacturing tolerance: ±0.002 mm Design & special features Workshop-version finish Single gauge pin configuration Supplied in a transport case FAQ What tolerance can be expected from this pin? The gauge pin is manufactured to a tolerance of ±0.002 mm, making it suitable for tight dimensional checks. What material is the pin made from? The pin is produced from special steel, specified for durability and wear resistance in workshop environments. Is the pin supplied ready for use and how is it packaged? Yes — the single test pin is finished for immediate use and is supplied protected in a transport case to prevent damage during handling. Which SKU and GTIN identify this product? This item is listed as SKU M323.D71 and GTIN 4061905069789 under the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.72mm Test Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, compact micro‑range sizing and robust workshop construction for reliable hole verification and assembly checks; order this gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, Ø 13.72 mm, 50 mm length — Metav IndustryLine Gauge pin, single, 13.72 mm for precise hole verification and end‑measure controls in workshop and inspection environments Workshop version for robust use Diameter 13.72 mm, precision ±0.002 Length 50 mm, hardened special steel Supplied in protective case Precision where tight fits are required The gauge pin is manufactured to deliver repeatable dimensional checks for bores and mating parts. With a nominal diameter of 13.72 mm and a stated tolerance of ±0.002 mm, this inspection pin supports axial and end‑measurement routines where small deviations matter. The compact geometry and controlled diameter make it suitable for comparative fits and functional checks in small assemblies; the specification helps to reduce ambiguous interpretations in routine quality control. Designed for frequent workshop use Built as a workshop version, the pin combines wear resistance with straightforward handling. The 50 mm length provides an accessible engagement depth for many standard components while keeping the probe lightweight at approximately 0.1 kg, aiding manual alignment and positioning. The choice of special steel ensures surface integrity under frequent contact, which translates into longer service intervals and fewer replacements in a production environment. How this aids quality assurance processes Integrating the pin into inspection sequences shortens go/no‑go decisions: the tight ±0.002 mm specification directly supports objective acceptance criteria, reducing rework and improving throughput. As a micro‑range instrument (appropriate for measurements under 100 mm), it is especially suited to precise tasks in precision engineering, toolmaking and component finishing where dimensional certainty is required at the point of assembly or during final inspection. Handling, storage and practical benefits The delivery in a protective case reduces the risk of transit or workshop damage and simplifies storage between uses. The compact form factor and clear dimensional specification make the pin easy to catalogue and retrieve for recurring checks. For users seeking dependable reference tools for hole gauges, plug checks or end‑dimension confirmation, this inspection pin offers a robust balance of precision, durability and workshop practicality. Contact Metav Werkzeuge for specification matching and to reserve this Metav IndustryLine gauge pin (SKU M323.D72) for your inspection equipment from our Emmerich stock Technical data Article number: M323.D72 GTIN: 4061905069796 Label: Gauge pin, single, 13.72 mm, length 50 mm Facts Diameter: 13.72 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Delivered in protective case Story trigger: end‑measure checks FAQ Is this gauge pin delivered ready for use? The gauge pin is supplied as a ready‑to‑use inspection item; the Metav IndustryLine gauge pin (SKU M323.D72) arrives protected in a case for immediate integration into inspection routines. What level of precision can be expected from the pin? The inspection pin is manufactured to a diameter of 13.72 mm with a tolerance of ±0.002 mm, providing the repeatability required for fine tolerance hole verification. Which materials is this pin suitable for checking? The gauge pin is intended for dimensional checks of holes and mating parts across typical workshop materials; the Metav IndustryLine gauge pin is used for end‑measure and bore verification in metal and engineered components. How should the pin be stored between uses? Store the pin in its protective case to prevent surface damage and contamination; keeping the tool dry and secured prolongs dimensional stability and service life. Can this pin be used for functional fit checks on assemblies? Yes, the pin’s controlled diameter and workshop‑grade construction make it suitable for plug‑fit and end‑measure checks within assembly and inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.73mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of ±0.002 mm tolerance and a robust special steel construction to secure reliable end‑measure checks in the workshop; order the pin via Metav Werkzeuge or consult our advisors for specification support. Gauge pin M323.D73 – single test pin, Ø 13.73 mm, length 50 mm (Metav IndustryLine) The gauge pin M323.D73 is a workshop‑grade test pin designed for accurate dimensional verification and end‑measurement tasks in production and inspection environments. Precision tolerance ±0.002 mm Diameter 13.73 mm, length 50 mm Workshop design, hardened special steel Accurate dimensional checks that reduce rework and scrap The M323.D73 delivers repeatable measurement accuracy thanks to its rolled and finished diameter of 13.73 mm and a verified tolerance of ±0.002 mm. In practice, this level of precision minimises false rejects and shortens inspection loops: a single, calibrated reference pin replaces time‑consuming comparisons and reduces the need for iterative machining corrections. The special steel construction preserves roundness and surface integrity under regular use, supporting consistent contact conditions for go/no‑go or reference gauging. For production planners, the measurable benefit is straightforward — fewer process stoppages and more predictable part yields. Robust workshop design for everyday handling and traceable checks Built as a workshop‑execution tool, the pin balances durability with manageable weight, making frequent handling straightforward. The 50 mm length provides ample engagement for end‑face and depth checks while remaining compact enough for handheld or fixture use. Ground and hardened surfaces reduce wear and maintain dimensional stability over long service intervals; this supports repeatability across batch inspections. Delivery includes a protective transport case to prevent damage during storage and transit, ensuring the instrument arrives ready for immediate use on the shop floor. Simple integration into inspection routines and fixtures The geometry of this test pin suits a variety of quality workflows: it functions as a reference for end‑measure tests, plug checks and fixture alignment. Where traceable calibration is required, the defined tolerance lets quality engineers set clear acceptance bands and document measurement uncertainty. The compact form factor eases incorporation into bespoke gauges or custom jigs without imposing undue mass or lever effects. With clear, numeric specification and a stable material base, the pin supports lean inspection setups and faster decision making in the quality loop. For workshop‑grade precision and dependable inspection results, request the Metav IndustryLine gauge pin M323.D73 from Metav Werkzeuge or contact our technical advisors via info@metav-werkzeuge.com for application advice and supply options Technical Data Article number: M323.D73 GTIN: 4061905069802 Manufacturer: Metav IndustryLine Facts Diameter: 13.73 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop execution Material: special steel Supplied in a transport case FAQ What tolerance does this gauge pin offer? The gauge pin M323.D73 is specified with a tolerance of ±0.002 mm, suitable for fine workshop and production checks. Is the pin suitable for fixture reference and alignment? Yes, the robust form and precise diameter of the M323.D73 make it appropriate for fixture alignment, plug checks and as a reference in jigs. What material is the pin made from and why does it matter? The pin is manufactured from special steel, selected to preserve roundness and resist wear during repeated contact measurements. Does the product arrive protected for transport? The test pin is supplied in a protective transport case to prevent handling damage and to keep the measuring surface intact. Can this pin be used for end‑measure checks on machined components? Its geometry and tolerance make the M323.D73 well suited to end‑measure verification and repeatable dimensional checks in production. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.74mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of 13.74 mm diameter, 50 mm length and a tight ±0.002 mm tolerance to secure repeatable end‑size inspections in the workshop; order the gauge pin directly via Metav Werkzeuge or consult our technical team for sizing advice. M323.D74 gauge pin — 13.74 mm Ø, 50 mm length (Metav IndustryLine) A M323.D74 gauge pin for precise end‑size inspection and plug checking in precision metrology and workshop quality control. Diameter 13.74 mm for end‑size checks Length 50 mm workshop version Tolerance ±0.002 mm high precision Special steel for robust everyday use Reliable accuracy for routine inspection The gauge pin delivers consistent dimensional control where repeatability matters. With a nominal diameter of 13.74 mm and a manufacturing tolerance of ±0.002 mm, this inspection pin supports high‑precision checks during incoming inspection, final control or setting tasks. The tight tolerance reduces rework and ambiguous decisions, so process stability and throughput improve without increasing cycle complexity. The compact form factor is optimised for insertion checks and ring or bore verification where a defined end measurement is required. Workshop design that endures daily use Built in a workshop execution and manufactured from special steel, the inspection pin is designed for frequent handling and rapid checks at the bench. The 50 mm active length gives a practical contact area while keeping handling simple for single‑handed operations or quick fixture checks. The choice of material and the rugged finish provide durability in standard shop environments, helping to maintain nominal diameter and surface condition over repeated use and ensuring a long service life under typical workshop stresses. Fits into quality workflows and gauge sets This inspection pin integrates easily into established quality routines and accessory fixtures. The straightforward geometry makes it suitable for use as a reference plug in gauges, for go/no‑go verification or as a master for visual comparison. Measurable benefits include faster inspection cycles and reduced measurement uncertainty due to the pin’s high repeatability. Documentation of the product specifications simplifies traceability and aids in audit situations, supporting quality management objectives without extra administrative burden. Contact Metav Werkzeuge for personalised advice on integrating the M323.D74 gauge pin into inspection routines or for assistance selecting matching sizes and holders — Metav Werkzeuge is ready to advise from Emmerich. Technical data Article number: M323.D74 GTIN: 4061905069819 Material: special steel Net weight: 0.1 kg Facts Diameter: 13.74 mm Length: 50 mm Tolerance: ±0.002 mm Category: single inspection pin Special features Workshop execution Story trigger: end‑size inspection ECLASS: 21170231 FAQ What material is the pin made from? The M323.D74 gauge pin is manufactured from special steel, selected to provide durability and dimensional stability for workshop inspection tasks. What accuracy can be expected from this inspection pin? The pin is produced to a tolerance of ±0.002 mm, delivering high precision suitable for reliable end‑size checks and repeatable measurements. For which applications is the pin intended? Designed for end‑size inspection, plug checking and use as a reference in gauge sets, the pin is suited to incoming inspection and routine shop checks. Is the length suitable for fixture use? The active length of 50 mm offers a practical balance between engagement depth and handling, making it compatible with common fixtures and quick verification routines. How is the product delivered? The item is supplied as a single inspection pin, ready for immediate use in workshop quality control and inspection procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.75mm Test Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise diameter control and a compact, workshop‑ready design to reduce inspection time and rework. The combination of ±0.002 mm repeatability, special steel construction and a rigid 50 mm length supports reliable end‑measure checks in production. Order the gauge pin directly via Metav Werkzeuge or consult the team for set configurations. Gauge pin, single, 13.75 mm, 50 mm length (Metav IndustryLine) The Gauge pin, single, 13.75 mm, 50 mm length is a workshop‑grade precision pin designed for end‑measure verification and fit checks in metrology and inspection environments. High precision ±0.002 mm Special steel construction 50 mm working length Supplied in transport case Consistent diameter control for fewer rejects The compact diameter of 13.75 mm combined with a verified positional accuracy of ±0.002 mm makes this pin suitable for fast go/no‑go checks and repeatable fit verification. Using a highly stable reference diameter reduces measurement scatter and prevents costly rework by ensuring that bores and mating parts comply with specified end dimensions. The result is a measurable improvement in process reliability and a lower rate of non‑conforming parts. Durable workshop design for everyday use Built as a workshop grade tool, the pin is manufactured from special steel to withstand handling and routine inspection cycles. With a 50 mm working length and a compact overall mass, the item balances rigidity with manoeuvrability for handheld checks and jigs. For transport and site handling the pin is supplied in a protective transport case, which keeps the measuring surface safe and simplifies storage between shifts. Easy integration into inspection routines As a single gauge pin, the component is intended for end‑measure and fit tests on shafts, bore gauges and assembly fixtures. Its small envelope supports quick insertion checks and compatibility with existing inspection rigs. When introduced into standard operating procedures, the pin accelerates quality gates and complements both manual and semi‑automated measurement setups, offering a straightforward way to raise daily inspection throughput. Trusted supply and practical service advantages Sourced via Metav IndustryLine, the product benefits from a European quality filter and the distributor’s long experience in metrology. Metav’s broad range and dependable logistics mean matching accessories or complementary sizes are readily available, helping workshops assemble coherent gauge sets without long lead times. The provenance and supply chain transparency support reproducible results across production batches. Contact Metav Werkzeuge to specify matching pins or to discuss batch supply and delivery options for the workshop‑grade gauge pin M323.D75 Technical data Article number: M323.D75 GTIN: 4061905065651 Label: Gauge pin, single, 13.75 mm length 50 mm Weight: 0.1 kg Facts Diameter: 13.75 mm Length: 50 mm Accuracy: ±0.002 mm Material: Special steel Special features Workshop execution Supplied in a transport case Single gauge pin for end‑measure applications FAQ What is the primary use of this gauge pin? The gauge pin M323.D75 is intended for end‑measure checks and fit verification in inspection routines, enabling rapid control of bore and shaft dimensions. What accuracy can be expected from this workshop pin? The gauge pin offers an accuracy of ±0.002 mm, providing reliable repeatability for routine production checks. What material is the pin made from and why does it matter? The pin is produced from special steel; this enhances surface durability for repeated insertion checks and supports longevity in a workshop environment. How is the pin delivered and stored? The pin is supplied in a protective transport case to preserve the measuring surface during handling and storage. How can the article be identified for reorder? Use the article number M323.D75 or GTIN 4061905065651 when reordering or specifying the item in procurement systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.76mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Combining workshop-grade construction, a compact Ø 13.76 mm diameter and a tight tolerance of ±0.002 mm, this single gauge pin delivers reproducible end‑measure checks and fixture alignment. Order the part directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single — Ø 13.76 mm, 50 mm length (Metav IndustryLine) The gauge pin is a workshop‑grade precision pin intended for end‑measure verification, alignment and plug‑gauge tasks in small‑part assembly and quality control. Workshop‑grade precision pin Diameter Ø13.76 mm, length 50 mm Tolerance ±0.002 mm for tight fits Made from special steel for durability Consistent fits for precision assemblies The compact design delivers repeatable positioning where small tolerances determine part function. With a diameter of Ø13.76 mm and a measured tolerance of ±0.002 mm, the pin provides the dimensional reliability required for final checks and go/no‑go verifications. Classified in the Mikro class (suitable for 10–100 mm gauges), this format combines short contact lengths with low flex, making it particularly suitable for delicate components and micro‑assemblies. The tight specification reduces rework and supports faster inspection cycles in production environments. Robust construction that endures workshop use Constructed from special steel in a workshop version, the pin balances wear resistance with dimensional stability during repeated use. The 50 mm length offers sufficient engagement for stable measurements while remaining manageable at the bench, and the single‑piece design simplifies handling and storage. The hardened surface preserves the nominal diameter under frequent contact, extending service life and maintaining the precision required for alignment jigs and fixture set‑ups. Practical handling and traceable performance Supplied as an individual test pin, the part streamlines inventory and enables targeted replacement in modular fixtures. The compact mass and familiar geometry make it easy to integrate into measurement routines without additional tooling. Identified as M323.D76, the gauge pin suits applications where consistent end‑measure checks and plug‑gauge comparisons are part of the quality workflow; documentation and batch identification support process control and traceability in standard workshop settings. For procurement and technical advice on the Metav IndustryLine M323.D76 gauge pin, contact Metav Werkzeuge to discuss suitability for specific fixtures or inspection plans and to arrange supply direct from Emmerich. Technical data Article number: M323.D76 GTIN: 4061905065668 Label: Prüfstift, einzeln, 13,76 mm Länge 50 mm Core specifications Diameter: Ø 13.76 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features / Materials Material: special steel Workshop version Single gauge pin, individual supply Suitable for end‑measure checks and fixture alignment Classified as Mikro (10–100 mm) FAQ What are the exact dimensions and tolerance of this pin? The M323.D76 gauge pin measures Ø13.76 mm with a length of 50 mm and a tolerance of ±0.002 mm, suitable for tight fit verifications. Is the gauge pin suitable for workshop use? Yes, the Metav IndustryLine workshop version is designed for routine bench use and offers enhanced durability for repeated checks. Is the item supplied as a set or individually? This entry is supplied as a single gauge pin; the product designation is M323.D76 and it is provided individually. What material is used and how does this affect wear? Made from special steel, the pin combines hardness with dimensional stability to resist wear during frequent contact operations. Which applications is this pin intended for? The pin is intended for end‑measure verification, plug‑gauge tasks, alignment and fixture checks in small‑part assembly and quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
13.77mm Gauge Pin 50mm Length Workshop Version, Special Steel ±0.002mm - Metav IndustryLine
Take advantage of a compact, workshop‑ready solution that combines a Ø 13.77 mm diameter with a 50 mm effective length and a tight accuracy of ±0.002 mm for consistent end‑dimension checks; the part is made from special steel and supplied in a transport case for protected handling. Order the gauge pin directly via Metav Werkzeuge or consult our technical advisors for application support. Gauge pin, single – Ø 13.77 mm, 50 mm length (Metav IndustryLine) A gauge pin, single, 13.77 mm Ø, 50 mm length designed for precise end‑dimension inspection, alignment checks and fixture set‑up in workshop and inspection environments. Precision tolerance ±0.002 mm Ø 13.77 mm, length 50 mm Special steel construction Workshop version, transport case included Reliable accuracy for end‑dimension inspection The measurement pin delivers industrial‑grade repeatability with a declared accuracy of ±0.002 mm, making it suitable for tight fit checks and dimensional verification tasks. With a nominal Ø 13.77 mm and a 50 mm usable shank, the component supports go/no‑go assessments and fine tolerance comparisons in inspection benches and gauge assemblies. The specified tolerance helps reduce rework and supports quality control protocols where measurable, repeatable results are required. Durable design for everyday workshop use Manufactured from special steel, the pin combines wear resistance and dimensional stability to withstand frequent insertion and handling typical in workshop environments. The workshop version designation indicates robustness and practicality: protected edges, straightforward geometry and a finish that eases cleaning. Delivery in a dedicated transport case preserves the gauge during storage and transit, reducing the risk of dings and maintaining measurement integrity between uses. Easy integration into inspection workflows This measurement pin is supplied individually and is simple to incorporate into existing fixtures or pin sets; the compact geometry reduces handling complexity and enables fast swap‑outs during set‑up. Traceable identifiers such as SKU and GTIN facilitate inventory control and documentation within quality systems. The combination of compact size, controlled tolerance and durable material supports efficient inspection cycles and reliable pass/fail decisions on the shop floor. Choose the Metav IndustryLine gauge pin for dependable, workshop‑ready inspection results and contact Metav Werkzeuge in Emmerich for tailored procurement or technical guidance. Technical data Article number: M323.D77 GTIN: 4061905065675 Eclass: 21170231 Label: Gauge pin, single, 13.77 mm length 50 mm SKU: M323.D77 Facts Diameter: 13.77 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Supplied in transport case Single piece delivery FAQ What accuracy can be expected from this gauge pin? The gauge pin is specified with an accuracy of ±0.002 mm, which supports tight dimensional checks and repeatable go/no‑go assessments for precision inspection tasks. Is the pin suitable for workshop use and transport? Yes, this Metav IndustryLine measurement pin is a workshop version and is supplied in a transport case to protect the pin during handling and transit. How is the product identified for inventory and traceability? Identification is provided via SKU M323.D77 and GTIN 4061905065675, enabling integration into inventory systems and quality documentation for the gauge pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com