Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
16.57mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of exact ±0.002 mm tolerance, a 16.57 mm diameter and a compact 50 mm length for reliable end‑measurement checks on the shop floor; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.G57 Gauge pin (16.57 mm × 50 mm) — Metav IndustryLine workshop version A M323.G57 single gauge pin for precise end‑measure verification and hole checking in workshop and inspection routines. Workshop version for heavy use Diameter 16.57 mm for end‑measure control Tolerance ±0.002 mm for high repeatability Length 50 mm for compact handling Reliable metrology for repeatable end measurements The compact design delivers consistent results when verifying hole diameters, dowel fits and end‑measure tolerances. With a nominal diameter of 16.57 mm and a stated accuracy of ±0.002 mm, the component offers a measurable reduction in rework and inspection variation compared with standard pins. The short, rigid profile maintains repeatability over repeated contact points, making it suitable for final checks during assembly and quality control. The specified tolerance is indicated in the technical data so measurement decisions rest on verifiable numbers rather than estimates. Robust build tailored to workshop environments Constructed from special steel, this single gauge pin is finished for frequent handling and offers stable mechanical contact under normal workshop conditions. The 50 mm overall length balances reach and control, keeping the centre of gravity close to the hand for steady guidance during insertion and withdrawal. At approximately 0.15 kg, the component feels substantial without being cumbersome, supporting efficient manual inspection cycles. The workshop version designation ensures the part withstands everyday wear while preserving dimensional integrity for sustained use. Traceability and integration into inspection workflows Supplied as an individual test pin, the item integrates cleanly with existing inspection routines and fixtures used for end‑measurement processes. The product is identified as M323.G57 with GTIN 4061905069437, allowing clear traceability in inventory and quality records. Its dimensions and material specification support compatibility with common gauge blocks, pin jigs and visual inspection procedures. Where documented tolerances are required for process control, the stated ±0.002 mm accuracy provides a firm basis for pass/fail criteria and reduces subjective judgement in routine checks. Contact Metav Werkzeuge for application guidance and to confirm fitment of the M323.G57 gauge pin into production inspection setups Technical data Article number: M323.G57 GTIN: 4061905069437 Brand: Metav IndustryLine Facts Diameter: 16.57 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Supply: Single gauge pin for end‑measurement FAQ What is the intended use for this gauge pin? The M323.G57 gauge pin is intended for end‑measure verification, hole checking and plug‑fit inspections in workshop and inspection environments. How precise is the M323.G57 during routine checks? The gauge pin is specified with an accuracy of ±0.002 mm, providing high repeatability for production control and final inspections. What material is the pin made from and why does it matter? Made from special steel, the pin combines wear resistance with dimensional stability, which preserves measured values over frequent use. Can the M323.G57 be used with standard pin jigs and fixtures? Yes, the dimensions (16.57 mm × 50 mm) and conventional geometry allow use with common jigs, blocks and measuring assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.58mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
A workshop-grade inspection pin combines compact dimensions, high repeatability and robust material for reliable end‑dimension checks; the ±0.002 mm tolerance and special steel construction make it a dependable reference in routine quality control. Order directly via Metav Werkzeuge or consult our specialists for selection and traceability. M323.G58 Gauge Pin (Ø 16.58 mm, 50 mm) — Workshop Version by Metav IndustryLine A M323.G58 gauge pin designed for precise reference and end‑dimension verification in workshop metrology, offering tight tolerance and compact handling for repeatable checks Workshop-grade precision component Diameter 16.58 mm, length 50 mm Tolerance ±0.002 mm for repeatable checks Supplied in protective transport case Precision that supports efficient quality control The compact cylindrical reference element delivers repeatable dimensional checks thanks to a specified tolerance of ±0.002 mm. In practice this level of accuracy reduces rework and speeds up inspection routines: when a reference component consistently returns near‑nominal values, process variation is easier to spot and correct. The pin’s dimensions — 16.58 mm diameter and 50 mm length — are chosen to provide a stable contact area while remaining easy to handle in a busy workshop environment. The component’s classification in the micro measuring range reflects its suitability for fine, short‑span reference tasks typical in toolrooms and small‑part inspection. Robust design for repeatability and handling Machined from special steel, this inspection pin resists wear and maintains a consistent bearing surface over repeated cycles, which preserves measurement confidence without frequent replacement. The plain cylindrical geometry simplifies calibration and seating, minimising sources of error that can originate from uneven contact or burrs. The workshop‑oriented execution ensures practical features for daily use: compact mass for single‑hand handling, a moderate overall weight for stable placement, and a finish that eases cleaning. Together, these aspects support quicker set‑ups and fewer interruptions during production or inspection runs. Traceability, delivery and integration into workflows Supplied individually and packaged in a protective transport case, the pin arrives ready for controlled storage and safe transport between benches or sites. Although the item is not marketed with a factory ISO 17025 certificate in the available data, the product is suitable for use as a stable reference in calibration chains and internal quality procedures. The clear numeric specification and the included GTIN make inventory and traceability straightforward for procurement and quality departments. For workshops seeking to streamline inspection points, small‑format gauge pins like this one integrate well into gaging sets or fixture checks and contribute to faster decision cycles on conformity. Choose the Metav IndustryLine M323.G58 gauge pin via Metav Werkzeuge for a compact, workshop‑ready reference standard that supports repeatable checks and straightforward inventory integration — contact Metav Werkzeuge for order and advice. Technical data Article number: M323.G58 GTIN: 4061905069444 ECLASS: 21170231 Manufacturer: Metav IndustryLine Weight: 0.15 kg Facts Diameter: 16.58 mm Length: 50 mm Accuracy: ±0.002 mm Special features Material: Special steel Workshop execution Supplied individually Protective transport case Single inspection/gauge pin FAQ Is the gauge pin suitable for routine workshop inspections? Yes. The M323.G58 gauge pin is intended for workshop metrology and routine reference checks where a compact, reliable cylindrical reference with ±0.002 mm tolerance is required. Can the pin be used for end‑dimension verification of turned parts? Yes. Its diameter and length make the gauge pin suitable for end‑dimension checks and reference seating in turned or machined components during inspection. How should the M323.G58 be stored to maintain accuracy? Store the gauge pin in the supplied protective transport case to avoid nicks and contamination; keeping the pin clean and dry preserves its measurement surface and repeatability. Is the material wear‑resistant enough for repeated contact checks? The pin is machined from special steel, providing good wear resistance for workshop applications and helping to maintain repeatable contact geometry over many cycles. Does the product come as a single item or in sets? The M323.G58 is supplied individually as a single inspection pin and packaged for safe transport and handling Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.59mm Gauge Pin Single, 50mm Length, Workshop Version - Metav IndustryLine
A robust choice for precise end measurements: the gauge pin combines 16.59 mm diameter accuracy with a 50 mm length and a manufacturing tolerance of ±0.002 mm, delivering reproducible checks on bores and fits. Built from special steel for wear resistance and supplied as a single-piece inspection pin, it supports efficient quality control routines. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.G59 — 16.59 mm diameter, 50 mm length (Metav IndustryLine) The Gauge pin M323.G59 is a precision cylindrical inspection pin designed for bore verification and end‑measurement tasks in workshop inspection and assembly environments. Precision diameter 16.59 mm Workshop version construction Length 50 mm for deeper bores Supplied in protective transport case Repeatable bore checks that reduce rework The cylindrical design with a nominal diameter of 16.59 mm and a verified accuracy of ±0.002 mm provides consistent contact geometry for repeatable measurements. Such stability minimises rework and shortens inspection cycles by reducing measurement scatter. The pin’s dimensional consistency supports go/no‑go assessment workflows and fixture validation, enabling machines and jigs to be set up with measurable predictability. Durable materials and handling suited to daily shop use Manufactured from special steel, the inspection pin is dimensionally stable under typical workshop conditions and offers elevated wear resistance compared with untreated steels. The 50 mm length gives access to moderately deep bores while maintaining a compact form factor that is easy to position in fixtures or hand inspections. A measured mass of 0.15 kg ensures steady contact during manual checks without excessive inertia, supporting reliable tactile feedback and handling. Traceability and practical integration into inspection routines The item is supplied as a single precision pin (SKU M323.G59) for straightforward inventorying and traceability within inspection records. The design suits use as an end‑measurement or reference pin in bench checks, assembly validation and alignment tasks. Clear identification via GTIN and SKU allows integration into stock systems and quality documentation, helping to maintain audit trails and assembly records. Contact Metav Werkzeuge in Emmerich for purchasing advice on the Metav IndustryLine gauge pin M323.G59: info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: M323.G59 GTIN: 4061905069963 Product label: Gauge pin, single, 16.59 mm diameter, length 50 mm Material: Special steel Weight: 0.15 kg Facts Length: 50 mm Diameter: 16.59 mm Accuracy: ±0.002 mm Mass: 0.15 kg SKU: M323.G59 Special features Workshop version Single-piece supply Category: Gauge pins Application: End measurements Protective transport case included FAQ Is this gauge pin suitable for bore verification in inspection fixtures? Yes. The gauge pin M323.G59 is designed for bore verification and integration into fixtures for end‑measurement and alignment tasks. What tolerance and resolution does the pin offer? The inspection pin provides a nominal diameter of 16.59 mm with a documented dimensional tolerance of ±0.002 mm, suitable for fine inspection work. What material is used and how does it affect durability? The pin is made from special steel, chosen for dimensional stability and enhanced wear resistance under regular workshop conditions. Is the product delivered as a single unit or in sets? This item is supplied as a single precision gauge pin (SKU M323.G59) for straightforward replacement and inventory management. Can the pin be used for alignment and assembly checks? Yes. The geometry and length make the pin suitable for alignment, assembly checks and as a reference element in inspection procedures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.5mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the workshop-grade construction, special steel and ±0.002 mm tolerance to secure repeatable end‑dimension checks in small-batch production; the compact form and transport case simplify handling and storage. Order the test pin directly via Metav Werkzeuge or consult the team for application advice. Test pin, single, 16.5 mm Ø, 50 mm length — Metav IndustryLine workshop gauge The test pin, single, 16.5 mm Ø, 50 mm length is a workshop-grade inspection gauge for fast end‑dimension verification and fixture checks in production and maintenance environments. Workshop-grade construction Diameter 16.5 mm precision Length 50 mm for compact checks Tolerance ±0.002 mm Stable measurement performance for routine inspection The compact test pin offers a reliably small contact diameter of 16.5 mm, backed by a declared measurement tolerance of ±0.002 mm. This level of precision supports consistent pass/fail decisions during final inspections and helps reduce rework rates by ensuring repeatable contact geometry. The low mass and rigid shank reduce bending and positional error when seated in pin blocks or fixture bosses, so dimensional checks become a deterministic step rather than a variable one. The choice of special steel improves wear resistance under frequent contact cycles, extending service intervals and lowering lifecycle cost. Robust design that suits shop-floor use Built as a true workshop version, the inspection pin tolerates everyday handling without sacrificing reference quality. The 50 mm overall length keeps the gauge short enough for confined fixtures while still providing adequate engagement for reliable measurements. Supplied for transport in a protective transport case, the pin arrives ready for safe storage and on‑bench use; the case mitigates shock and contamination risks during transit. The modest mass (approx. 0.15 kg) balances ease of handling with sufficient heft to avoid accidental displacement, supporting quick, one‑person inspection routines. Ready-to-fit into quality workflows and documentation Marked and traceable as M323.G50, the pin integrates smoothly into established inspection plans and inventory systems; the included GTIN enables barcode-driven part management. As a single‑piece gauge, it is ideal for end‑dimension checks, go/no‑go verification and use as a reference in jig and fixture set‑ups. The compact geometry and consistent contact surface simplify automation or semi‑automated inspection steps, shortening cycle times and improving throughput. Metav IndustryLine’s practical focus on accessibility and supply reliability means well-documented, workshop-suitable gauges are available without long lead times. For application guidance or to secure the Metav IndustryLine M323.G50 test pin for your inspection routine, contact Metav Werkzeuge in Emmerich to discuss fitment and availability Technical Data Article number: M323.G50 GTIN: 4061905068546 Label: Test pin, single, 16.5 mm Ø, 50 mm length Facts Diameter: 16.5 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop-grade construction Material: special steel Supplied in protective transport case Category: Gauge pin / inspection pin FAQ What materials is this test pin suitable for when used as a reference in fixtures? The M323.G50 test pin is made from special steel, suitable as a reference contact in fixture and gauge applications rather than as a cutting or machining tool. Can this pin be used for automated pick-and-place inspection systems? Yes, the compact geometry and consistent contact surface of the inspection pin make it suitable for integration into automated or semi‑automated inspection cycles. How does the declared tolerance affect pass/fail limits in quality control? The ±0.002 mm tolerance provides a predictable uncertainty band for end‑dimension checks, enabling narrowly defined acceptance criteria and reducing false rejects in high‑precision assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.61mm Gauge Pin 50mm Length Workshop Finish, Special Steel in Plastic Case - Metav IndustryLine
Take advantage of precision ground dimensions and tight tolerance for consistent end‑measure verification; combine ±0.002 mm accuracy, a 16.61 mm diameter and robust special steel construction for reliable workshop use. Order directly via Metav Werkzeuge or consult our specialists for procurement and availability. Gauge pin, 16.61 mm Ø, 50 mm length — Metav IndustryLine Gauge pin 16.61 mm (50 mm length) is a single, precision‑ground inspection pin suitable for end‑measure checks and go/no‑go verification in the workshop High precision ±0.002 mm Diameter 16.61 mm exact fit 50 mm length, workshop version Special steel construction Precision that reduces rework and speeds inspection The gauge pin provides a guaranteed reference for end‑measure checks thanks to its ±0.002 mm tolerance. With a hard, machined diameter of 16.61 mm and a compact 50 mm length, the pin enables fast, repeatable go/no‑go testing and positional verification on small to medium components. By using a dedicated inspection pin rather than improvised gauges, measurement uncertainty is reduced and process rejects can be identified earlier, improving throughput and lowering rework costs. Robust construction for routine workshop environments Manufactured in special steel and supplied as a single, workshop‑grade item, this inspection pin is designed for everyday handling and repeated use. The workshop version balances hardness and toughness to withstand knocks and frequent insertion without immediate wear, preserving the calibrated diameter over many cycles. The straightforward geometry and solid material simplify cleaning and upkeep, making the tool an efficient choice for production checks and inline inspection points. Practical integration and traceability for quality routines The compact form factor and clear specification make the pin easy to incorporate into fixture checks, bore verification and dimensional control routines. Marked identification and the supplied article data enable traceability within inspection logs and process documentation. Using standardised, precision reference pins supports consistent measurement results across shifts and operators, contributing to a measurable improvement in quality assurance. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge for technical advice and availability to secure this gauge pin for your inspection kit. Technical details Article number: M323.G61 GTIN: 4061905070433 Label: Gauge pin, single, 16.61 mm Ø, length 50 mm Measurements Diameter: 16.61 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.15 kg Measuring range min/max: 16.61 mm Features & construction Material: special steel Version: workshop execution Single inspection pin Category: gauge pins FAQ What applications suit this gauge pin? This gauge pin is intended for end‑measure checks, bore verification and go/no‑go inspection in workshop and production environments; the M323.G61 from Metav IndustryLine serves as a compact reference for routine dimensional checks. How precise is the measurement reference provided by the pin? The pin is manufactured to an accuracy of ±0.002 mm, giving a stable reference for tight inspection limits and repeatable go/no‑go testing. Which material is used for the pin and what does that mean in practice? Made from special steel, the pin offers a balance of hardness and durability suitable for regular workshop use while maintaining its dimensional integrity under normal handling. Can this pin be integrated into inspection fixtures? Yes — the clear diameter and length specifications allow straightforward incorporation into fixtures, measurement jigs and standardised inspection routines. Is the pin supplied individually or in sets? The product is supplied as a single inspection pin (single unit), intended for direct use in inspection or as a replacement reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.62 mm Gauge Pin, Single, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of high metrological certainty, a compact workshop design and certified traceability to keep inspection cycles short and reproducible. With a 16.62 mm diameter, a ±0.002 mm tolerance and a stable 50 mm shank, the pin supports reliable end‑dimension checks; order directly via Metav Werkzeuge or ask our consultants if needed. M323.G62 gauge pin — 16.62 mm diameter, 50 mm length (Metav IndustryLine) The M323.G62 gauge pin is a workshop‑grade measuring pin designed for precise end‑dimension checks and repeatable gauging in production and inspection environments. Workshop version for everyday use Precision diameter 16.62 mm Tight tolerance ±0.002 mm 50 mm length for secure seating Accuracy that shortens inspection loops A measuring tool with a specified ±0.002 mm deviation establishes a clear, technical basis for decisions in quality control. The tight tolerance reduces ambiguous readings and minimises rework by delivering consistent contact conditions during verification. Used as a fixed‑dimension reference, the pin converts a subjective feel for fit into an objective pass/fail criterion, which improves throughput where small deviations carry production consequences. The combination of diameter control and low variation supports statistical process control and simplifies acceptance protocols. Rugged workshop design for dependable handling Produced in a workshop version and made from special steel, the pin is engineered for the handling patterns common in daily shop use. The 50 mm shank length gives sufficient engagement for stable seating in gauge plates, fixtures or assembly checks while keeping the overall bulk compact. At roughly 0.15 kg the component is easy to place and reposition without compromising stiffness. The simple, fixed geometry means no adjustments are required on the shop floor, so checks can be executed quickly and with reproducible force application. Traceability and practical integration into inspection workflows Marked by SKU and GTIN for inventory control, the pin supports orderly storage and traceable insertion into inspection plans. Intended for end‑dimension checks, the tool fits into existing gauging stations and handheld verification routines alike. The clear specification of 16.62 mm diameter and accuracy allows planners to allocate it to tolerance stacks and first‑article inspections with confidence. Metav IndustryLine combines broad product availability with a quality filter at the Emmerich site, which improves supply reliability and reduces the administrative effort of sourcing calibrated references. Contact Metav Werkzeuge to discuss Metav IndustryLine gauge pins and ensure the M323.G62 meets specific inspection plans and fixture interfaces Technical data SKU: M323.G62 GTIN: 4061905070440 ECLASS: 21170231 Label: Prüfstift, einzeln, 16,62 mm Länge 50 mm Brand: Metav IndustryLine Facts Diameter: 16.62 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.15 kg Measurement range min/max: 16.62 mm Special features Workshop execution Material: Special steel Intended use: end‑dimension checks Category: Measuring pins FAQ What applications suit this measuring pin best? The M323.G62 gauge pin is intended primarily for end‑dimension checks and repeatable fit verification in production and inspection contexts, supporting plug, seat and go/no‑go style assessments. How precise is the M323.G62 in routine use? Specified at ±0.002 mm, the pin provides a high level of dimensional certainty suitable for fine inspection tasks where small deviations influence assembly or function. Is the material suitable for regular workshop handling? Constructed from special steel, the pin combines durability with the surface integrity required for repeated contact during everyday gauging operations. How is the item identified for stock and traceability? The product is listed under SKU M323.G62 with GTIN 4061905070440, which facilitates inventory control and integration into inspection documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.63mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of the combination of high repeatability, compact dimensions and robust workshop design to ensure reliable end‑dimension checks. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for specification advice. Gauge pin M323.G63 — Single precision test pin, Ø 16.63 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.G63 is a single precision test pin for end‑dimension verification and setting tasks in fine mechanical and workshop environments. High repeatability ±0.002 mm Ø 16.63 mm diameter 50 mm overall length Special steel, workshop version Precision where small tolerances matter This test pin delivers repeatable measurements with a stated tolerance of ±0.002 mm, making it suitable for setup and verification tasks where small deviations are critical. As a compact measuring master, the pin's dimensions provide a clear reference for bore checks, go/no‑go verifications and fixture setting. The narrow tolerance reduces rework and shortens inspection loops while the simple geometry minimises uncertainty caused by alignment. Compact design for micro‑range applications Classified in the micro range, the pin is tailored for very compact measuring tasks with a maximum range of 16.63 mm. Such dimensions suit fine mechanical workshops and precision assemblies where short gauge lengths reduce flex and improve handling stability. The overall 50 mm length balances reach and rigidity, allowing accurate placement in shallow bores or when setting gauges without compromising control. Robust materials for workshop durability Manufactured from special steel, the pin combines surface hardness and corrosion resistance needed for repeated use in workshop environments. The workshop version construction emphasises durability under frequent handling and transport. Delivered in a dedicated transport case, the item remains protected between uses, preserving geometry and ensuring consistent performance across measurement cycles. Practical benefits for production and inspection Using a dedicated test pin simplifies routine checks: fewer setup steps, faster alignment and clear go/no‑go criteria. As a single, well‑defined master, the component supports traceable inspections and can serve as a reference in quality control procedures. The compact format also makes it convenient to store alongside other precision tools, improving workflow efficiency on the shopfloor. Contact Metav Werkzeuge in Emmerich for procurement and specification support on the Metav IndustryLine gauge pin M323.G63; technical advice and delivery coordination are available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.G63 GTIN: 4061905070457 Label: Prüfstift, einzeln, 16,63 mm Länge 50 mm Brand: Metav IndustryLine Facts Diameter: 16.63 mm Length: 50 mm Weight: 0.15 kg Accuracy: ±0.002 mm Special features Material: Special steel Workshop version Delivered in transport case Measurement range classification: Micro (max 10–100 mm) FAQ What is the intended use of this test pin? The gauge pin M323.G63 is intended for end‑dimension checks, bore verification and fixture setting in precision workshop and fine‑mechanical applications. Is the measurement accuracy sufficient for quality control tasks? With an accuracy of ±0.002 mm, the M323.G63 gauge pin provides the repeatability required for tight tolerance checks and routine quality inspections. Which materials is the pin suitable to be used with during inspection? The test pin itself is made from special steel and is designed for non‑destructive checking of components made from typical engineering materials; it functions as a dimensional reference rather than a cutting tool. How is the pin supplied and protected during transport? The M323.G63 is supplied as a single pin in a transport case appropriate for workshop handling, ensuring the measuring surface remains protected between uses. Can this pin be used for both go/no‑go and setting applications? Yes, the compact geometry and precise diameter of the M323.G63 make it suitable as a master for go/no‑go assessments and for setting gauges or fixtures. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.64mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from tight diameter control and a robust workshop design for reliable end‑measure checks; the high dimensional repeatability and protective transport case reduce downtime and handling risks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.G64 — Ø 16.64 mm, 50 mm length (Metav IndustryLine) A gauge pin M323.G64 designed for precise end‑measurement and set‑up tasks in workshop and inspection environments. Workshop version for daily use Diameter tolerance ±0.002 mm Made from special steel 50 mm length for end measurements Precise tolerances for repeatable end‑measure checks The gauge pin delivers a diameter of 16.64 mm with a documented tolerance of ±0.002 mm, providing the dimensional stability required for tight go/no‑go checks and assembly verification. Such accuracy ensures consistent results when used as an end‑measure or reference pin in fixtures and jigs, reducing the need for repeated adjustments and supporting efficient quality workflows. The compact 50 mm length suits confined spaces while still offering sufficient engagement for many inspection tasks. Built for the workshop — durable materials and handling Designed as a workshop version, the pin is manufactured from special steel chosen for wear resistance and dimensional stability under frequent use. The solid construction keeps weight low (approx. 0.15 kg) while supporting robust handling during routine checks. Supplied in a protective transport case, the component is easier to store and move between workstations, lowering the risk of damage and preserving calibration between uses. Practical uses in inspection, set‑up and end‑measure applications The inspection pin is ideal for end‑measure tasks, alignment of mating parts, and setting reference points in assembly processes. Its specification makes it suitable for precision checks on shafts, bores and fixture faces where a defined diameter is required to verify clearance or concentricity. Using a dedicated gauge pin streamlines calibration of measurement fixtures and contributes to faster set‑up times on production and maintenance jobs. Integration with shop processes and supply reliability As part of the Metav IndustryLine, the component complements a broader programme of workshop tools and measuring aids that aim to make precision accessible across industry. The straightforward geometry reduces training effort for operators, while the documented tolerance supports traceable quality control steps. For procurement, the compact format simplifies storage and reuse in multi‑station environments. For a reliable supply of workshop‑grade gauge pins from Metav IndustryLine and to discuss tolerance suitability for specific applications, please contact Metav Werkzeuge at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article: Gauge pin M323.G64 GTIN: 4061905070464 Brand: Metav IndustryLine Data Diameter: 16.64 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Single piece delivery Supplied in protective transport case FAQ What dimensional tolerance does the gauge pin offer? The gauge pin is specified with a tolerance of ±0.002 mm, ensuring high repeatability for end‑measure tasks with the M323.G64 from Metav IndustryLine. Is the pin suitable for everyday workshop use? Yes, the workshop design and the choice of special steel make the pin resilient under frequent handling and routine inspection work. Can this pin be used as a reference for assembly set‑ups? The pin’s precise diameter and short length make it suitable for fixture alignment, reference positioning and quick go/no‑go checks during set‑up. What protection is provided for transport and storage? The item is supplied in a protective transport case to reduce handling damage and maintain dimensional integrity between uses. How is this product identified for ordering? Ordering can be done using the designation M323.G64 (gauge pin) and the GTIN 4061905070464 for unambiguous identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.65mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of high repeatability and workshop-ready robustness thanks to a special-steel construction and a narrow tolerance of ±0.002 mm; the pin gauge delivers reliable end-measurements in small-batch inspection. Order the component directly via Metav Werkzeuge or consult the Metav team for specification matching and stock information. Pin gauge, single, Ø 16.65 mm, length 50 mm (Metav IndustryLine) The pin gauge, single, Ø 16.65 mm, length 50 mm is a precision end-measurement pin designed for repeatable dimensional checks and gaging applications in workshop and inspection environments Diameter Ø16.65 mm precision Tolerance ±0.002 mm accuracy Length 50 mm workshop version Made from special steel Reliable dimensional control for end-measurements A compact, single pin gauge engineered for precise end-measurement tasks. The nominal diameter 16.65 mm with an indicated tolerance of ±0.002 mm establishes a tight baseline for go/no-go checks and comparator routines. Such accuracy reduces ambiguity during final inspections and supports consistent pass/fail decisions on small components. The marked tolerance corresponds to industrial inspection practice where reproducibility between operators and measuring stations is essential, so the item functions well as a reference in short-range verification workflows. Built for workshop handling and longevity Constructed from special steel, this workshop-grade gauge pin balances wear resistance with stable geometry over repeated use. The 50 mm length gives sufficient engagement for many end-measurement setups while remaining easy to handle during frequent checks. The workshop specification highlights robust finishing and dimensional stability, which means less frequent replacement and a predictable service life. Where measuring jigs and fixture interfaces demand repeatable contact geometry, the pin's profile and material choice preserve accuracy across routine cycles. Practical use cases and system compatibility The single-pin format suits small-batch inspection, fixture validation and integration into gauge sets or calibration jigs. It is appropriate for short-range comparative measurements, end-face checks and sampling routines in machining, assembly and quality-control shops. Identification for procurement and inventory is straightforward via SKU M323.G65 and GTIN 4061905070471, enabling clear traceability within toolrooms and stores. As a compact, workshop-ready element, the pin complements broader metrology equipment where space and repeatability are priorities. For precise end-measurement requirements, contact Metav Werkzeuge for detailed advice on the Metav IndustryLine pin gauge and to secure SKU M323.G65 for immediate workshop replenishment. Technical Data Article number: M323.G65 GTIN: 4061905070471 Manufacturer: Metav IndustryLine Facts Diameter: 16.65 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Material: Special steel Workshop version Single pin for end measurements FAQ What tolerance does the pin provide and what does that mean in practice? The pin gauge specified with a tolerance of ±0.002 mm gives a tight dimensional band for acceptance testing; this level of precision supports consistent go/no-go decisions and reduces measurement scatter in routine inspection with the Metav IndustryLine pin gauge (SKU M323.G65). Which material is used and how does it affect durability? The component is made from special steel, selected to provide stable geometry and wear resistance under typical workshop conditions; this material choice helps the pin retain its dimensional integrity during frequent contact operations. For which measurement tasks is this pin most suitable? This single pin is intended for end-face checks, fixture validation and comparative measurements in machining and assembly environments where compact reference elements are needed for rapid inspections. Is the item supplied individually or as part of a set? The product is supplied as a single pin, suitable for addition to existing gauge sets or for use as a standalone inspection element in the workshop. How can the item be identified for ordering or inventory? Use SKU M323.G65 and GTIN 4061905070471 when ordering or updating stock records to ensure accurate procurement and traceability. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.66mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact, workshop‑ready test pin that combines a precise 16.66 mm diameter with an industrial‑grade ±0.002 mm tolerance and a robust 50 mm length for reliable end‑measurement and setting tasks; order via Metav Werkzeuge or consult the in‑house specialists for application advice. Gauge pin, single — 16.66 mm dia, 50 mm length (M323.G66) — Metav IndustryLine Gauge pin, single — 16.66 mm dia, 50 mm length (M323.G66) is a workshop‑grade test pin for end‑measurement, go/no‑go checks and master setting in production and inspection environments Workshop‑grade construction for daily use Diameter 16.66 mm with ±0.002 mm accuracy Length 50 mm for stable handling Made from special steel for wear resistance Repeatable accuracy where it matters Engineered for reproducible end‑measurements, this gauge pin delivers a measured tolerance of ±0.002 mm, making it suitable for precise inspection tasks and repeat checks on production lines. The close tolerance reduces measurement uncertainty when used as a reference or setting master, and the compact geometry supports quick, successive checks without complex fixturing. The item is identified as M323.G66, enabling straightforward integration into inventory and quality documentation. Robust construction minimises maintenance intervals The workshop execution reflects a focus on durability: a special steel composition and a short, solid design provide resistance to wear and bending during frequent handling. The 50 mm body length ensures a firm grip and stable seating in holders or between centres while the nominal 16.66 mm diameter maintains contact geometry for consistent results. The relatively low mass (0.15 kg) eases handling and reduces the risk of accidental impact damage compared with longer, heavier pins. Simple traceability and practical use in inspection routines Marked and stocked under SKU M323.G66 and GTIN 4061905070488, the test pin is easy to track in inspection workflows and parts lists. Its single‑piece configuration is intended for direct use in end measurement, master setting and go/no‑go checks; the short length supports rapid insertion and extraction during batch inspections. Documentation of dimensions and tolerance simplifies acceptance criteria in quality plans and inspection reports. Request the M323.G66 specification sheet from Metav Werkzeuge or ask our Emmerich team for an application recommendation tailored to production requirements Technical data Article number: M323.G66 GTIN: 4061905070488 Category: Messstifte SKU: M323.G66 Core specifications Diameter: 16.66 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Material: Special steel Features Workshop version Single test pin Application: End measurements Identification: M323.G66 FAQ What measurement tolerance does this test pin provide? The M323.G66 gauge pin is specified with a tolerance of ±0.002 mm for repeatable end‑measurement tasks. Which material is used for the pin? The pin is made from special steel, selected for durability and wear resistance in workshop environments. Is this item suitable as a setting master for inspection fixtures? Yes, the 16.66 mm diameter and stable 50 mm length make the pin suited for use as a reference or setting master in fixtures and inspection aids. How is the product identified for procurement and stock control? Identification is via SKU M323.G66 and GTIN 4061905070488 for clear traceability in procurement and quality documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.67mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, compact form and wear‑resistant construction to secure consistent fit checks and reduce rework. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for specification advice. Gauge pin M323.G67 — Test pin, Ø 16.67 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.G67 is a single workshop‑grade test pin for checking bores, fits and alignment in production and maintenance environments. Workshop‑grade construction for daily use Diameter Ø 16.67 mm with ±0.002 mm accuracy Length 50 mm for fixture and gauge checks Made from wear‑resistant special steel Consistent precision for repeatable fits Inspection tasks demand predictable results; the workshop test pin delivers this through a tight tolerance of ±0.002 mm on a nominal Ø 16.67 mm diameter. The small geometric deviation reduces uncertainty in bore and fit control, which in turn cuts time spent on rework and adjustments. In practice, the pin functions as a reliable reference for alignment checks and go/no‑go verifications, supporting a measurable increase in first‑pass quality. Durable construction tailored to everyday workshop use A workshop‑grade design and special steel construction combine to offer abrasion resistance and dimensional stability under frequent handling. At 50 mm length and approximately 0.15 kg, the pin is compact yet substantial enough to resist deformation during routine use, giving long service life in production and maintenance benches. The robust finish simplifies cleaning and preserves contact geometry, so downtime for replacement is reduced. Easy integration into inspection workflows and inventory systems The single‑piece pin is straightforward to deploy within fixtures, go/no‑go arrays and manual inspection jigs, enabling quick checks without elaborate setup. Clear identification via SKU and GTIN ensures traceability and simplifies stock management when multiple sizes are used across departments. Sourcing from a supplier with an established European logistics base supports steady replenishment and coherent quality control across sites. For precise fit verification choose Metav IndustryLine’s M323.G67; contact Metav Werkzeuge in Emmerich for tailored advice and prompt supply coordination Technical Data Article number: M323.G67 GTIN: 4061905071317 Manufacturer: Metav IndustryLine Material: Spezial‑Stahl Facts Diameter: 16.67 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop execution Single gauge pin for bore and fit checks Category: Gauge pins FAQ What tolerance can be expected from this gauge pin? The M323.G67 gauge pin is specified with a tolerance of ±0.002 mm, making it suitable for tight fit and bore verification in workshop environments. Is the pin suitable for repeated use in production fixtures? Yes; the workshop‑grade construction and special steel material make the pin resilient to frequent handling and routine contact with fixtures. How is the item identified for inventory and traceability? Identification is provided via the SKU M323.G67 and the GTIN 4061905071317, which support straightforward stock management and traceability. Can this pin be used for alignment checks as well as bore gauging? The pin’s nominal diameter and accurate geometry allow it to be used for both alignment and bore gauging tasks where a solid reference mandrel is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.68mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, tight ±0.002 mm accuracy and compact 50 mm length for repeatable end‑dimension checks; order this item directly via Metav Werkzeuge or consult the Metav team for application advice Gauge pin, single Ø 16.68 mm – 50 mm length (Metav IndustryLine) The Gauge pin, single Ø 16.68 mm is a workshop-grade measuring pin designed for precise end‑dimension inspection and layout in mechanical workshops and production environments Workshop-grade construction Diameter specified to 16.68 mm Accuracy ±0.002 mm Supplied in a protective case Reliable precision where small tolerances matter This measuring pin is engineered to deliver consistent precision for end‑dimension checks and gauging tasks. Manufactured from special steel, the component combines surface hardness with dimensional stability to resist wear over repeated use. The ±0.002 mm accuracy rating underlines suitability for fine measurement tasks where tight tolerances are required; this level of exactness supports quality control in assembly and final inspection operations and reduces the need for repetitive rework. Compact format that simplifies handling and setup With a 50 mm overall length and a defined diameter of Ø 16.68 mm, the pin offers a compact footprint that is simple to position and align in jigs, fixtures or measuring plates. The short, stiff profile assists in repeatable seating and minimises bending during single‑hand handling, which speeds up routine checks on production lines. The design is particularly effective for end‑mass measurements and small component verification where accessibility and repeatability are critical. Workshop readiness and durable delivery Supplied in a protective case appropriate for workshop transport, the pin is ready for daily use without additional packaging work. The workshop-grade execution reflects practical demands: robustness for routine handling, resistance to incidental knocks and an overall build geared to frequent use. For procurement and logistics, the compact package reduces storage space while keeping the measuring surface protected between uses. Fit for standard inspection workflows The pin is ideal for being integrated into manual inspection sequences, plug‑gauge checks and layout procedures. Its material composition and dimensional definition simplify pairing with comparator stands or go/no‑go setups. Where traceable measurements are required for part acceptance, the clear specification of diameter and accuracy makes documentation straightforward and supports conformity checks during in‑process and final inspections. Contact Metav Werkzeuge for detailed application advice and to arrange supply of this Metav IndustryLine gauge pin; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.G68 Brand: Metav IndustryLine GTIN: 4061905071324 Facts Length: 50 mm Diameter: 16.68 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop-grade execution Material: Special steel Supplied in protective case FAQ What is the primary use of this gauge pin? The gauge pin M323.G68 from Metav IndustryLine is intended for end‑dimension inspection and routine gauging tasks in workshop and production settings What material is the pin made from and how does that help? The Metav IndustryLine gauge pin is manufactured from special steel, which provides wear resistance and dimensional stability for repeatable measurements How precise is the measuring pin for inspection tasks? The measuring pin is specified with an accuracy of ±0.002 mm, making it suitable for fine inspection and acceptance checks where tight tolerances are required Is the pin delivered ready for workshop use? Yes, the gauge pin is supplied in a protective case, enabling safe transport and immediate use in workshop environments Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.69mm Gauge Pin, Workshop Version, 50mm Length, Special Steel, Calibrated, Packed in Case - Metav IndustryLine
Take advantage of a combination of workshop-grade robustness and fine dimensional control: the gauge pin is produced from special steel, measures Ø 16.69 mm with a 50 mm length and delivers a repeatable ±0.002 mm tolerance for reliable end‑dimension checks; order directly via Metav Werkzeuge or consult our specialists for application support. Gauge pin M323.G69 — Single test pin, Ø 16.69 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.G69 is a single precision test pin designed for end‑dimension verification and fixture alignment in workshop metrology. Single precision gauge pin Ø 16.69 mm 50 mm length, workshop-grade design Dimensional tolerance ±0.002 mm Supplied in protective transport case Precise results for routine end‑dimension checks A compact, single test pin offers straightforward verification of final dimensions and reference points. With a nominal diameter of Ø 16.69 mm and an indicated ±0.002 mm dimensional variation, this tool reduces uncertainty in repeat measurements and supports consistent quality control. The tight tolerance suits fine inspection tasks where deviation margins are narrow, enabling process stability and fewer rejects. The gauge pin functions as a clear mechanical reference for go/no‑go comparisons and fixture set‑up without the need for complex instrumentation. Built for workshop durability and handling ease Constructed from special steel and finished in a workshop-grade execution, the pin withstands daily handling and maintains dimensional integrity. The 50 mm length balances reach and rigidity to simplify insertion and removal in fixtures or bores, while a modest mass ensures safe, ergonomic handling. Delivery in a protective transport case preserves the measuring surface during storage and transport, helping to retain calibration and extend service life. This robustness translates into lower lifetime costs because frequent replacements and handling damage are minimised. Practical uses and measurement workflow benefits Engineered primarily for end‑dimension checks, the test pin is suitable for setting up jigs, verifying bore sizes and establishing datum points during assembly. Its single‑piece design provides a tactile reference that complements optical or digital measuring systems, serving as a quick check during setup or in-process inspection. For workshops working with small series or custom fixtures, the gauge pin speeds routine checks and simplifies operator workflows by offering a reliable mechanical standard that integrates easily into existing measurement routines. Why Metav IndustryLine is the pragmatic choice Metav IndustryLine supplies a wide range of precision tools with a focus on practical workshop use; the M323.G69 benefits from this approach in its balanced specification and protective packaging. Metav’s presence in Emmerich functions as a quality filter for the European market, backed by decades of distribution experience and a broad product range that reduces the need for multiple suppliers. This proximity and product breadth support reliable replenishment and consistent quality control for day‑to‑day production requirements. For workshop-ready precision, request the M323.G69 from Metav Werkzeuge — contact our Emmerich team for tailored advice and prompt dispatch Technical Data Article number: M323.G69 GTIN: 4061905071331 Label: Prüfstift, einzeln, 16,69 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 16.69 mm Length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop version Supplied in protective transport case Application: End‑dimension checks Material: Special steel FAQ What tolerance can be expected from this test pin? The gauge pin delivers a dimensional tolerance of ±0.002 mm, making the M323.G69 suitable for fine workshop checks where close repeatability is required. Is the pin supplied ready for storage and transport? Yes, the M323.G69 is supplied in a protective transport case to preserve the measuring surface during storage and transit. What are the typical applications for this gauge pin? The pin is intended for end‑dimension verification, fixture alignment and quick go/no‑go checks in workshop metrology. Which material is the gauge pin made from? The test pin is manufactured from special steel, selected for dimensional stability and durability under workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.6mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop‑grade robustness, ±0.002 mm dimensional accuracy and a compact 50 mm length for repeatable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin M323.G60 (single) – Ø 16.6 mm, 50 mm length, Metav IndustryLine A gauge pin M323.G60 engineered for precise end‑measurements and routine inspection tasks in workshop and production environments Workshop version for robust handling Precision tolerance ±0.002 mm Special steel, hardened for wear resistance High precision for decisive inspection results The single measuring pin delivers a tolerance of ±0.002 mm, which establishes it as a reliable reference for tight fit checks and end‑measurement tasks. This level of accuracy reduces uncertainty in pass/fail evaluations and supports consistent assembly outcomes. The nominal diameter Ø 16.6 mm is manufactured to tight limits so that repeat measurements remain comparable; in practice this means fewer reworks and clearer go/no‑go decisions at the inspection stage. Built to withstand workshop routines Constructed from special steel, this workshop configuration resists wear during frequent use and maintains contact geometry over time. The compact 50 mm length provides a stable, easy‑to‑handle measuring element that fits standard bench fixtures and quick‑check stations. Supplied in a protective transport box, the pin stays organised and protected in transit or on the shop floor, simplifying storage and reducing the risk of damage between shifts. Practical use and handling benefits Designed for routine end‑measurements, the gauge pin is suitable for verifying bore sizes, checking alignment and validating mating parts in small‑batch production. The moderate mass supports steady hand placement while remaining light enough for repeated manual checks; the construction supports quick introduction into pre‑existing fixtures and measuring rigs. The single design and workshop finish mean dependable performance where clarity and repeatability are essential—ideal for production inspectors and toolroom technicians seeking a robust reference pin. Contact Metav Werkzeuge for tailored advice or to arrange supply from our Emmerich warehouse; technical consultants are available to confirm fit and application for Metav IndustryLine products Technical data Article number: M323.G60 GTIN: 4061905070426 Label: Gauge pin, single, 16.6 mm, length 50 mm Facts Nominal diameter: 16.6 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop version Material: Special steel Supplied in a protective transport box Application focus: end measurements eClass: 21170231 FAQ What is the dimensional tolerance of this gauge pin? The gauge pin M323.G60 offers a dimensional tolerance of ±0.002 mm, making it suitable for precision end‑measurement tasks in workshop and inspection settings. What material is used for the pin? This Metav IndustryLine gauge pin is made from special steel, selected for wear resistance and stability under frequent contact use. Is the pin delivered ready for storage and transport? Yes, the pin is supplied in a protective transport box to keep the measuring face and shaft secure during storage and transit. For which inspection tasks is this pin suitable? The M323.G60 single gauge pin is intended for end‑measurements such as bore checking, alignment verification and plug‑type fit assessments in routine production controls. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.7 mm Precision Gauge Pin, 50 mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of precise end‑dimension checks, robust workshop construction and a compact form factor for fast, repeatable inspections. Order the gauging pin directly via Metav Werkzeuge or consult the Metav team for assistance with application-specific recommendations. Gauging pin (single) — 16.7 mm Ø × 50 mm, workshop version (Metav IndustryLine) The gauging pin (single) 16.7 mm Ø × 50 mm is a compact precision check pin designed for routine end‑dimension verification in workshop and production environments Workshop version for robust daily use Diameter 16.7 mm, length 50 mm Manufactured from special steel Tolerance ±0.002 mm for precise checks Rapid, measurable assurance for end‑dimension inspection The Metav IndustryLine gauging pin provides a measurable and repeatable reference for end‑dimension checks, thanks to its ±0.002 mm tolerance. That level of accuracy reduces uncertainty in comparative checks and helps to detect deviations early in the process, shortening inspection times and lowering rework rates. The compact geometry makes the pin well suited to tight fixtures and end‑face checks, while the hard, consistent surface finish supports repeated seating without measurable wear during normal workshop use. Durability and handling that suit everyday workshop routines Constructed from special steel and released as a workshop version, the pin resists routine knocks and handling typical of production environments. Its 50 mm length and balanced mass (approx. 0.15 kg) make it easy to position in jigs or between centres, while the solid shaft minimises bending and distortion during contact checks. Delivery in a protective transport case ensures the gauge arrives ready for use and remains protected when carried between workstations. Integrates with inspection workflows to increase throughput The single pin is intended for straightforward go/no‑go and dimensional comparison tasks on finished parts and assemblies. Used as a reference mandrel or plug, it speeds up repeat checks and can be incorporated into fixture‑based routines for quick verification of bores, seats and end faces. For consistent results, pair the pin with a calibrated comparator or micrometre and document readings as part of the quality record; the result is a traceable, efficient inspection step that supports production control and process confidence. For tailored advice on using the Metav IndustryLine gauging pin M323.G70 in specific applications, contact Metav Werkzeuge in Emmerich for guidance and ordering options Technical data Article number: M323.G70 GTIN: 4061905071348 Brand: Metav IndustryLine Version: workshop execution Core measurements Diameter: 16.7 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Materials & special features Material: special steel Delivered in transport case for protection Workshop execution for daily use Intended use: end‑dimension checks FAQ What is the declared tolerance of the gauging pin? The Metav IndustryLine gauging pin M323.G70 is specified with a tolerance of ±0.002 mm, making it suitable for fine comparative checks and repeatable workshop inspection tasks. Which material is the pin made from? The pin is made from special steel, chosen for mechanical stability and resistance to wear during routine use. Is the pin supplied ready for use and protected for transport? Yes — the gauging pin M323.G70 is supplied in a protective transport case to safeguard the surface and maintain dimensional integrity during handling. Can this pin be used for go/no‑go checks on finished bores and seats? The single pin is well suited to go/no‑go and plug checks on end faces, bores and seats; it integrates easily into fixture‑based inspection routines for fast verification of end dimensions. Is the Metav IndustryLine pin intended for workshop environments? The M323.G70 is the workshop version, designed specifically for robust daily use in production and workshop settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.71mm Gauge Pin Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of the combination of tight tolerance, compact design and robust construction for reliable end‑measurements and repeatable inspection results. Order directly via Metav Werkzeuge or consult our specialists for application advice. Metav IndustryLine Gauge Pin — 16.71 mm Ø, 50 mm Length A gauge pin (16.71 mm, 50 mm) designed for precision end‑measurements, alignment checks and inspection tasks in workshop and quality environments High accuracy ±0.002 mm Special steel for durable service 16.71 mm diameter, 50 mm length Single-piece supply for flexible inventory Precision where it matters The gauge pin delivers a measured accuracy of ±0.002 mm, which corresponds to a dimensional deviation of just 2 µm and supports tasks that demand fine tolerances. With a nominal diameter of 16.71 mm and a compact 50 mm length, this cylindrical reference is ideal for tight end‑measurements, plug checks and alignment operations. The small form factor reduces operator influence and helps maintain consistent contact conditions, improving repeatability during serial inspection and set‑up procedures. Workshop-ready durability and handling benefits Constructed from special steel, the pin is engineered for repeated use in demanding workshop environments. The material choice balances wear resistance with manageable handling weight (approx. 0.15 kg), allowing single‑handed placement during quick checks and minimising fixture downtime. Supplied as a single unit, this workshop version simplifies stocking and rotation in tool cabinets while reducing the risk of mix‑ups during inspection routines. Integration, traceability and practical use This item is intended as a precise reference for end‑measurements and go/no‑go verification in assembly, maintenance and incoming inspection. The product is identified by article number M323.G71 and GTIN 4061905071874, which supports traceability and inventory control in production environments. For customers needing clarification on application scenarios or measurement set‑ups, Metav Werkzeuge provides technical guidance to ensure the gauge pin is applied in a way that preserves accuracy and reduces rework. Choose Metav IndustryLine's precision gauge pin for dependable end‑measurements; contact Metav Werkzeuge in Emmerich for tailored advice and order handling via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.G71 GTIN: 4061905071874 Manufacturer: Metav IndustryLine Label: Gauge pin, single, 16.71 mm, length 50 mm Facts Diameter: 16.71 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version (Werkstatt‑Ausführung) Single‑piece supply Intended use: end measurements / inspection FAQ What tolerance can be expected from this gauge pin? The gauge pin from Metav IndustryLine offers a tolerance of ±0.002 mm, suitable for inspection tasks requiring micrometre‑level precision. Which materials is the pin suitable for when used as a reference during inspection? As a dimensional reference, the gauge pin is material‑agnostic in use; it provides a stable datum when checking components made from steel, aluminium or other workpiece materials. How is the product supplied and identified for inventory? The item is supplied single‑piece and identified as M323.G71 with GTIN 4061905071874 to support traceability and stock management. Can this gauge pin be used for alignment and plug checks on assemblies? Yes, the 16.71 mm diameter and compact 50 mm length make the gauge pin well suited to alignment tasks, plug checks and end‑dimension verification in workshop and production settings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.72mm Gauge Pin Workshop Version 50mm Length - Metav IndustryLine
Take advantage of precise end‑measurement capability, a compact 50 mm usable length and ±0.002 mm tolerance for reproducible inspection results; order the gauge pin directly via Metav Werkzeuge or request advice from our consultants for integration into quality workflows. Gauge pin M323.G72 – precision 16.72 mm Ø, 50 mm length | Metav IndustryLine The gauge pin M323.G72 is a workshop‑grade precision pin for end‑measurement and bore inspection in fine mechanical and assembly applications. Precision diameter 16.72 mm ±0.002 mm 50 mm usable length for end‑measurements Workshop version, robust special steel Supplied in protective transport case Repeatable inspection with sub‑10‑micrometre control The gauge pin is manufactured to a tight ±0.002 mm tolerance, which equates to a repeatability in the low micrometre range suitable for demanding inspection tasks. Made from special steel, the pin offers stable behaviour under repeated measuring cycles; the narrow dimensional tolerance supports reliable comparison measurements, pass/fail checks and reference gauging without frequent rework of the measuring stack. This level of accuracy positions the item for quality control procedures where small deviations must be detected and documented. Compact micro class design for fine assemblies Classified in the Micro class, the diameter of 16.72 mm and the short, stiff 50 mm profile provide excellent handling for fine mechanical components. The compact geometry reduces flex and twisting during engagement, improving positional certainty when inspecting small bores, plug fits or end‑faces. These characteristics make the pin well suited to precision sub‑assemblies and tasks where space is limited but measurement certainty remains critical. Robust workshop execution and transport protection Engineered as a workshop version, the pin combines practical durability with metrological stability: corrosion‑resistant finishing and the choice of special steel ensure dimensional integrity across normal shop use. Supplied in a protective case for secure transport, the pin is ready for field inspections or bench storage while reducing the risk of impact damage. The compact mass (approx. 0.15 kg) keeps handling straightforward during repetitive quality checks. Select the Metav IndustryLine gauge pin M323.G72 for precision end‑measurements and contact Metav Werkzeuge for availability and order coordination at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.G72 GTIN: 4061905071881 Brand: Metav IndustryLine Facts Diameter: 16.72 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Delivery: workshop version Packaging: protective transport case Item type: single gauge pin FAQ What is the intended use of this gauge pin? The gauge pin M323.G72 is intended for end‑measurements and bore inspection in fine mechanical assembly and quality control. How precise is the M323.G72 in practical terms? With a tolerance of ±0.002 mm, the M323.G72 delivers micrometre‑level repeatability suitable for tight inspection limits and reliable pass/fail gauging. Is the pin suitable for portable inspections? Yes, the workshop version is supplied in a protective transport case and is designed for both bench and field inspection tasks. Which measurement class does this product belong to? This gauge pin falls into the Micro class, offering compact dimensions and stiffness appropriate for small parts and fine mechanical applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.73mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a combination of high dimensional accuracy (±0.002 mm), a workshop‑grade special‑steel construction and compact handling for reliable process checks — ideal where repeatable reference measurements are required. Order the gauge pin directly via Metav Werkzeuge or request further information from our consultants. Gauge pin M323.G73 — single test pin, 16.73 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin designed as a workshop‑grade reference and go/no‑go aid for inspection and assembly tasks in industrial metrology. Single gauge pin, diameter 16.73 mm, length 50 mm Workshop-grade special steel construction Dimensional tolerance ±0.002 mm for fine precision Supplied in protective transport case Repeatable reference measurements with micrometre‑level accuracy This test pin delivers a concise metrological basis for routine inspection and reference tasks. The specified tolerance of ±0.002 mm supports precise pass/fail checks and dimensional comparisons where small deviations matter; this level of accuracy is suitable for quality control tasks that demand consistent, repeatable results. By referencing a stable diameter rather than relying on temporary setups, process variability is reduced and measurement throughput is improved. The hard‑wearing geometry maintains form under repeated seating, so inspection cycles remain predictable. Durable workshop design for daily use Constructed from special steel, the pin is tailored to withstand the knocks and handling of a busy shop floor while keeping its measuring surface intact. The compact form factor — 16.73 mm diameter and 50 mm length — provides a balance between reach and rigidity, simplifying insertion into bores or jig features without flexing. Supplied in a protective transport case, the item is delivered ready for safe storage and transfer between workstations. The robust finish aids corrosion resistance and prolongs service life, which reduces replacement frequency and supports continuous operation. Practical integration into inspection and assembly workflows As a single test pin, the component is straightforward to deploy for assembly verification, fixture setting, and dimensional control on the production line. The compact mass and consistent geometry make it suitable for slotting into existing inspection fixtures or for use as a tactile reference in manual checks. Identification is clear through the item code M323.G73, which streamlines ordering and stock management. Where traceable calibration or certificates are required, additional services are available from Metav Werkzeuge to match enterprise traceability needs. Contact Metav Werkzeuge for procurement assurance and reliable supply from Emmerich — request item M323.G73 from our consultants via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.G73 GTIN: 4061905071898 Label: Prüfstift, einzeln, 16,73 mm Länge 50 mm Key figures Diameter: 16.73 mm Length: 50 mm Weight: 0.15 kg Dimensional tolerance: ±0.002 mm Special features Workshop‑version construction Material: special steel Supplied in transport case Single gauge/test pin FAQ What is the material of the pin and how robust is it? The pin is made from special steel and the workshop‑grade construction is intended for regular use in inspection and assembly environments. What accuracy can be expected during routine checks? The item is manufactured to a dimensional tolerance of ±0.002 mm, allowing fine precision for pass/fail and reference measurements. Is the pin suitable for use in bore gauging and fixture alignment? Yes — the diameter and length combination provides a stable reference for bore checking, fixture setup and tactile alignment tasks. How can the part be identified for reordering? Reorder using the article number M323.G73 and GTIN 4061905071898 for clear identification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.74mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of workshop-grade construction, pinpoint ±0.002 mm tolerance and a compact Ø 16.74 mm × 50 mm format for reliable end‑measure checks. Order the gauging pin directly via Metav Werkzeuge or consult the team for specification support. Gauging pin M323.G74 – Gauge pin Ø 16.74 mm, 50 mm length (Metav IndustryLine) Gauging pin M323.G74 designed for precise end‑dimension verification in workshop and inspection environments; compact format ideal for fine fixtures and component end‑measurements. Workshop‑grade finish and robust design Tolerance ±0.002 mm for high reproducibility Solid special steel construction Supplied in a protective transport case Accuracy that reduces rework and inspection time The compact cylindrical pin delivers consistent dimensional references thanks to its ±0.002 mm specification, minimising measurement scatter in repetitive checks. With a Ø 16.74 mm diameter and 50 mm length the component serves as a stable datum for end‑face and bore checks, improving throughput by reducing the need for repeat setups. The tolerance is stated as a deviation value, helping quality teams plan acceptance limits and SPC procedures with confidence. Built for workshop conditions and daily handling Constructed from special steel with a workshop‑grade finish, the pin resists wear from routine contact while remaining straightforward to clean and store. The chosen material offers a balance between hardness and toughness appropriate for frequent use in jigs, fixtures and shop inspection benches. Its compact dimensions make it easy to position in tight assemblies and to integrate into measuring routines without complex fixturing. Practical integration into quality control workflows Marked for traceable identification as M323.G74, the pin is suitable for use as a reference artefact in incoming inspection, in‑process checks and final acceptance tests. The small footprint allows storage in standard tooling drawers or transport in the supplied protective case, ensuring repeatable handling and reducing the risk of transit damage. The detailed dimensional specification supports exchange of data with inspection protocols and documentation systems. Why this format is often preferred for fine measurements Pins in this size class fall into the micro category of reference gauges, where stiffness, minimal bending and exact diameter control are decisive for accurate end measurements. The combination of a short gauge length and robust material keeps deflection low, which is particularly valuable when verifying small parts, gauge blocks or finishing fixtures. This format therefore complements both manual gauges and optical checking methods, supporting consistent results across different measurement stages. For procurement or technical queries regarding the M323.G74 from Metav IndustryLine, contact Metav Werkzeuge for tailored advice and local delivery from Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M323.G74 GTIN: 4061905071904 Manufacturer: Metav IndustryLine Facts Diameter: 16.74 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Special features Workshop‑grade design Material: special steel Supplied in protective transport case Label: Gauging pin, single, Ø 16.74 mm, length 50 mm FAQ What is the dimensional tolerance of this gauging pin? The gauging pin M323.G74 is specified with a dimensional tolerance of ±0.002 mm, suitable for high‑repeatability inspection tasks. Is the pin suitable for routine use in a machine shop environment? Yes, the workshop‑grade construction and special steel material make the pin well suited for regular handling in machine shop and inspection bench settings. How is the M323.G74 supplied for transport and storage? The pin is supplied in a protective transport case to prevent handling damage and to simplify storage between uses. Can the M323.G74 be used as a reference for end‑face and bore checks? The compact Ø 16.74 mm × 50 mm format is intended for end‑dimension verification and is appropriate for both end‑face and small‑bore reference checks. Which identifier should be quoted when ordering spare or replacement pins? Please refer to the article number M323.G74 (GTIN 4061905071904) for orders and specification requests. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.75mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of precision and workshop-ready robustness combined with a protective transport case for reliable end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or contact our consultants for specification advice. M323.G75 gauge pin — Ø 16.75 mm, 50 mm length (Metav IndustryLine) The M323.G75 gauge pin is a workshop‑grade cylindrical reference pin designed for end‑dimension verification and assembly checks in metalworking environments. High concentricity ±0.002 mm Ø 16.75 mm, 50 mm length Workshop‑grade special steel Supplied in protective transport case Precision that keeps production within tolerance The gauge pin delivers high concentricity with a stated tolerance of ±0.002 mm, making it suitable for fine inspection tasks and final size verification. This degree of accuracy supports repeatable pass/fail assessments and reduces uncertainty when checking shafts, bores and mating parts. The numerical tolerance represents the maximum permissible deviation in diameter and is indicative of the component’s suitability for precision assembly and quality control routines. Robust construction for everyday workshop use Manufactured from special steel and specified as a workshop‑grade product, the test pin resists wear during routine handling and in-line checks. The material choice balances hardness and toughness to maintain dimensional stability during repeated use, while the single‑piece design minimises sources of error. Robustness in this context translates into longer service life and fewer replacements, which supports steady production throughput. Practical handling and traceable identification With a 50 mm length and a diameter of 16.75 mm, the pin provides a compact, easy‑to‑manipulate reference that fits typical inspection fixtures and gauges. The unit is supplied as a single piece, cleared for immediate integration into measurement benches or go/no‑go jigs. Clear identification via SKU and GTIN ensures simple inventory control and traceability in documentation and inspection records. Protects accuracy in transport and storage Delivered in a protective transport case, the pin arrives shielded from shocks and contamination that could compromise surface finish and dimensional integrity. The case is intended for safe transport and handling between workstations or job sites; by protecting the reference surface, it helps preserve the pin’s calibration and reduces the need for premature rework or replacement. Suited for rigorous workshop inspection routines As a workshop tool, the gauge pin supports fast, rational inspection workflows: set the reference, perform the check, and document results. Its compact geometry and stable material properties enable consistent measurements with micrometre and caliper systems, helping to streamline quality control and minimise downtime in production or maintenance cycles. For reliable end‑dimension checks request the Metav IndustryLine M323.G75 via Metav Werkzeuge — technical advice and stock information available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.G75 GTIN: 4061905068645 Numbers / core technical data Diameter: 16.75 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Designs / special features Workshop‑grade execution Material: special steel Supplied single (single unit) Protective transport case for delivery FAQ What is the intended application for this gauge pin? The M323.G75 gauge pin is intended for end‑dimension verification, assembly checks and pass/fail testing of shafts and bores in workshop environments. How precise is the diameter of the pin? The diameter tolerance for the pin is ±0.002 mm, which ensures tight concentricity for reliable inspection results. Is the gauge pin supplied ready for use? Yes, the pin is supplied as a single unit in a protective transport case and is ready for integration into inspection fixtures. What material is the pin made from and why does it matter? The M323.G75 is made from special steel, chosen to provide a balance of wear resistance and dimensional stability for repeated workshop use. Can the pin be used for traceable inventory and documentation? The product is identified by SKU M323.G75 and GTIN 4061905068645 to support inventory control and inspection record keeping. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.76mm Gauge Pin Workshop Version Length 50mm - Metav IndustryLine
Take advantage of the combination of workshop‑grade construction, special steel and ±0.002 mm tolerance for consistent fit control in production and inspection tasks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if additional information is required. Gauge pin M323.G76 — Precision gauge pin Ø 16.76 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.G76 is a workshop‑grade precision plug designed for end‑measure checks and fit verification in assembly and inspection contexts. Precision diameter 16.76 mm Tolerance ±0.002 mm 50 mm hardened length Delivered in transport case Consistent, measurable accuracy for fit verification A hardened gauge pin with a diameter of 16.76 mm and an indicated accuracy of ±0.002 mm provides a reliable reference for go/no‑go and clearance checks. The tightly specified tolerance transforms ambiguous fit assessments into verifiable decisions, reducing rework and stoppages. By using a fixed‑size, hardened pin, repeatable results are achieved in serial inspection or setup tasks, which improves process stability and quality documentation. Robust construction that suits the workshop environment Built in a workshop‑grade layout and made from special steel, this plug offers durability against everyday handling and light knocks during bench work. The 50 mm length gives secure support in bores while remaining compact for quick handling and insertion. Supplied in a transport case, the item is protected during storage and transport between inspection buggies or workstations, maintaining the reference surface and prolonging service life. Efficient integration into inspection routines and traceability Marked for easy identification and traceability, the pin fits into standard plug‑gauge workflows and supports rapid dimension checks during assembly or incoming inspection. The compact mass and simple geometry allow ergonomic handling during repetitive checks, speeding up throughput without compromising measurement certainty. GTIN and article details facilitate inventory management and reordering within procurement systems. For reliable workshop measurement and long‑term repeatability, contact Metav Werkzeuge in Emmerich to discuss the Metav IndustryLine gauge pin M323.G76 and its suitability for specific fit‑control tasks. Technical data Article number: M323.G76 GTIN: 4061905068652 Brand: Metav IndustryLine Facts Diameter: 16.76 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop execution Delivered in transport case Category: Gauge pins FAQ What is the exact diameter and tolerance of this gauge pin? The gauge pin has a diameter of 16.76 mm with a tolerance of ±0.002 mm as listed for M323.G76 from Metav IndustryLine. Is the pin suitable for repeated use in a workshop? Yes, the workshop‑grade construction and special steel material make the plug robust for repeated insertion and removal during standard inspection cycles. How does the 50 mm length affect usability? A 50 mm length provides stable seating in standard bores while remaining compact enough for quick handling and minimal overhang during bench checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.77mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial‑grade precision, robust special steel construction and convenient transport protection to keep inspection routines efficient and reproducible; order the test pin directly via Metav Werkzeuge or consult our specialists for specification matching. M323.G77 test pin — gauge pin, 16.77 mm diameter, 50 mm length (Metav IndustryLine) The M323.G77 test pin is a single precision gauge pin for end‑measure and limit checks in workshop and incoming‑inspection environments, offering a defined 16.77 mm diameter and a 50 mm overall length. Precision tolerance ±0.002 mm Diameter 16.77 mm, length 50 mm Special steel for enhanced wear resistance Delivered in a transport case Precision where repeatable decisions are required The M323.G77 is manufactured to a tight tolerance ±0.002 mm, making it suitable for fine end‑measure tasks and pass/fail checks where small deviations affect assembly quality. The defined diameter of 16.77 mm and the 50 mm working length provide a clear reference for gauges, go/no‑go fixtures and calibration routines. Using a single, hard‑finished gauge pin reduces measurement variation compared with improvised checking tools, which in turn lowers the risk of rework and improves throughput in serial inspection processes. Durable workshop design for daily handling Constructed from special steel, this workshop version is designed for repeated use under industrial conditions. Surface hardness and finishing ensure dimensional stability and resistance to contact wear, while the compact mass (approx. 0.15 kg) keeps handling comfortable during fast inspection cycles. The delivery in a transport case protects the datum faces and minimises the need for frequent rework or replacement, so production lines and quality stations remain productive with minimal downtime. Practical integration and operational benefits As a standard gauge pin for metrology benches and control fixtures, the component supports straightforward integration into existing measurement setups and inspection jigs; its clear nominal diameter simplifies documentation and traceability. The measured certainty provided by precision components from Metav IndustryLine helps purchasing and quality teams standardise inspection procedures, shorten decision loops and make compliance reporting more reliable. For complex queries, technical clarification or batch procurement, direct consultation keeps the process efficient and aligned with shop‑floor needs. For specification matching and procurement of the Metav IndustryLine M323.G77 test pin, contact Metav Werkzeuge for tailored advice and reliable delivery from Emmerich. Technical Data SKU: M323.G77 GTIN: 4061905068669 Label: Test pin, single, 16.77 mm diameter, length 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 16.77 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Configuration: Workshop version Delivery: Transport case included FAQ What inspection tasks is this gauge pin suitable for? The M323.G77 test pin is intended for end‑measure and limit checks, making it suitable for incoming inspection, fixture verification and simple go/no‑go evaluations in the workshop. Is the material specified for long‑term wear resistance? Yes, the gauge pin is made from special steel; this material choice improves surface durability and supports repeatable dimensional performance. Can the pin be used directly in existing jig and fixture systems? The nominal diameter and fixed length allow straightforward use as a reference element in jigs, fixtures and comparative gauges; integration is typically direct provided the fixture accepts the 16.77 mm datum. Does the delivery include protective packaging? Delivery includes a transport case to protect the datum faces and maintain dimensional integrity during storage and transit. How can procurement or quality teams get further technical details? For batch sizes, material certificates or application advice, Metav Werkzeuge can provide tailored technical information and procurement support. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.78mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
The compact design and workshop-grade construction make this gauge pin a reliable choice for routine inspection and fixture set-up; its 16.78 mm nominal diameter with a 50 mm length and a close ±0.002 mm tolerance ensure consistent results on repeat measurements—order the gauge pin directly via Metav Werkzeuge or consult our specialists for tailored advice. Gauge pin M323.G78 – 16.78 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.G78 is a single precision pin for diameter verification and fixture alignment in inspection and workshop environments Precise Ø 16.78 mm nominal Compact 50 mm length for fixtures Tolerance ±0.002 mm for tight control Workshop-grade special steel construction Accuracy that stabilises process control This inspection pin delivers industrial-grade repeatability through a ±0.002 mm dimensional window, which corresponds to a deviation of just two micrometres. The closely held tolerance supports consistent go/no-go checks, in-process gauges and alignment operations, reducing scrap and rework. With a nominal Ø 16.78 mm and a 50 mm functional length, the pin is sized for compact fixtures and jigs where axial run-out and seating precision matter; the relatively low mass contributes to easy handling while maintaining the rigidity required for quick tactile gauging. Built for everyday workshop use Constructed from special steel in a workshop configuration, this single gauge pin balances corrosion resistance and wear performance for frequent use. The surface finish and material selection help maintain mating fits with bore gauges and bushings, which means fewer adjustments during production runs and less downtime for replacements. Lightweight yet robust at approximately 0.15 kg, the pin is suited to manual handling and fits common inspection trays and holders, offering a practical combination of durability and operator convenience that supports steady throughput. Practical benefits for inspection and fixture set-up As a dedicated measuring and alignment element, this gauge pin integrates easily into inspection routines and fixture checks. The nominal size and tolerance make it suitable for final-size verification and for establishing reference positions in modular tooling. Traceable identification such as the SKU and GTIN simplify inventory and quality records: the product is listed under SKU M323.G78 and GTIN 4061905069451, supporting systematic stock control. The simple geometry reduces interpretation effort during checks, enabling technicians and inspectors to focus on measurement outcomes rather than on complex set-up procedures. Discuss the workshop-grade gauge pin M323.G78 with Metav Werkzeuge for precision fixture checks or request a customised quotation through Metav Werkzeuge. Technical data Article number: M323.G78 GTIN: 4061905069451 Brand: Metav IndustryLine Facts Diameter: 16.78 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: special steel Single gauge pin design Workshop version FAQ How precise is this gauge pin for routine checks? The gauge pin M323.G78 offers a tolerance of ±0.002 mm, providing micrometre-level precision suitable for routine inspection and go/no-go verification. Is the material suitable for frequent handling and light exposure to workshop environments? Yes, the pin is made from special steel in a workshop-grade configuration, which combines wear resistance and practical durability for everyday use. Can this pin be used for fixture alignment as well as dimensional checks? The nominal Ø 16.78 mm and 50 mm length make the pin well suited to both fixture alignment and final-size verification in toolrooms and assembly jigs. What identifiers help with stock and quality management? The product is listed as SKU M323.G78 and GTIN 4061905069451, which assists with traceability and inventory control. Is this gauge pin compatible with standard bore gauges and holders? The simple cylindrical geometry and standard nominal diameter ensure compatibility with common bore gauges and fixture holders; the close tolerance supports reliable seating. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16.79mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of precise diameter control (16.79 mm) and a tight tolerance of ±0.002 mm to standardise end‑of‑line inspections and reduce rework. The 50 mm length and workshop‑grade construction ensure durable handling during routine checks. Order via Metav Werkzeuge or consult the technical team for selection and supply. Gauge pin M323.G79 – single test pin, 16.79 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.G79 is a single‑piece test pin designed for rapid limit and reference checks in workshop and inspection settings. Diameter 16.79 mm ±0.002 mm accuracy 50 mm overall length for end measurements Special steel construction for workshop use Single-piece gauge pin, delivered individually Consistent, measurable accuracy that shortens inspection cycles The pin's 16.79 mm diameter combined with an accuracy of ±0.002 mm provides a reliable reference for go/no‑go checks and comparative measurements. A stable nominal size reduces variation between successive measurements and simplifies decision rules during quality control. Using a defined hardened reference in inspection routines makes tolerance assessments reproducible and speeds up throughput by lowering the need for repeat checks. Robust workshop design for everyday handling Manufactured from special steel and specified as a workshop version, the pin tolerates frequent handling and the knocks associated with shop‑floor use. The 50 mm length offers good engagement for end measurements without excess overhang, improving handling safety and repeatability. The single‑piece design removes joint‑related uncertainties, making it suitable as a fixed reference in fixtures and manual gauging tasks. Practical integration into inspection workflows The item is supplied individually for straightforward inventory control and quick access during batch inspections. As a simple mechanical reference, the test pin integrates directly into visual and tactile inspection processes, complementing digital gauges or calipers where a hard physical limit is required. Clear labelling and the compact form factor support portable measurement kits and mobile quality checks across multiple production points. For procurement or technical clarification regarding the Metav IndustryLine gauge pin M323.G79, please contact Metav Werkzeuge GmbH in Emmerich via info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss fitment and delivery options. Technical data SKU: M323.G79 GTIN: 4061905069468 Name: Gauge pin, single, 16.79 mm, length 50 mm Weight: 0.15 kg Material: Special steel Facts Diameter: 16.79 mm Length: 50 mm Accuracy: ±0.002 mm Mass: 0.15 kg Special features Workshop version Single-piece delivery Application: end gauge / reference pin Supplied individually FAQ What are the main dimensions and tolerance of this gauge pin? The gauge pin M323.G79 from Metav IndustryLine has a diameter of 16.79 mm, an overall length of 50 mm and a tolerance of ±0.002 mm. Can this pin be used as a fixed reference in a fixture? Yes, the single‑piece construction and workshop‑grade special steel make the gauge pin suitable for use as a fixed reference in fixtures and manual gauging operations. Is the item supplied individually or as a set? This product is supplied individually; the M323.G79 is delivered as a single test pin for immediate use or inventory stocking. Which applications suit this test pin best? Typical applications include go/no‑go checks, end‑of‑line limit inspections, reference measurements and incorporation into portable measurement kits. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com