Quick, secure clamping with lever clamps
Lever clamps provide rapid, repeatable workholding for fixture building, assembly, welding and testing, using the kinematic knee-lever principle to deliver self-locking retention and resist process vibrations. Designed for metalworking applications and made from high-strength materials such as zinc-plated steel or stainless steel, these clamps reduce setup and handling times while enabling high holding forces with minimal operator effort. Available in vertical and horizontal versions as well as thrust bar and closure styles, lever clamps ensure consistent positioning, long service life and enhanced process reliability for serial production. Key advantages include self-locking mechanism, high repeatability, reduced setup time and robust construction.
90° 100mm Pneumatic Clamp With Massive Holding Arm, 3,000N Thrust 3,300N Hold, Galvanised - Kukamet
Benefit from the combination of a 100 mm holding arm, galvanised construction and up to 3,300 N holding force for secure, repeatable clamping in production environments. Order the pneumatic clamp directly via Metav Werkzeuge or consult our specialists for fixture configuration. Pneumatic clamp 651 — Kukamet, 100 mm arm, vertical base The Pneumatic clamp 651 is a compact lever clamp intended for vertical mounting, providing a robust 100 mm holding arm and precise 90° positioning for repeatable workholding. Robust 100 mm holding arm Vertical base for stable mounting Galvanised finish resists corrosion Up to 3,300 N holding force Consistent clamping for reliable cycle times The pneumatic actuation and specified force ratings ensure repeatability across long production runs. With a maximum holding force of 3,300 N and a maximum pressing force of 3,000 N, the unit secures components reliably without frequent retightening, which reduces cycle interruptions and rejects. The pneumatic drive converts compressed-air input into a rapid, consistent clamping motion, making the solution suitable for automated or semi-automated stations where predictable clamping behaviour is essential. Clear numerical ratings support process planning and fixture design. Durable construction for tough workshop environments A galvanised finish and a massive holding arm provide long service life in demanding conditions. The vertical base offers a compact footprint while enabling secure attachment to jigs and fixture plates; the lever clamp layout concentrates force into a short, stiff clamp lever to minimise deflection. Corrosion-resistant coating extends maintenance intervals and preserves tolerances in mixed-material workshops. The robust mechanical design is intended to withstand repetitive loads and retain clamping accuracy over thousands of cycles, supporting consistent quality control. Simple integration and predictable positioning Designed for 90° clamping applications, the unit installs via a vertical base that simplifies alignment in common fixture geometries. The combination of a defined clamp angle and 100 mm arm length reduces the need for extensive adapter hardware, accelerating assembly of modular fixtures. Standardised eClass and ETIM identifiers support parts lists and CAD procurement, while the compact actuator requires minimal space on the assembly table. The consistent stroke and force values ease the calculation of required air pressure and safety margins when integrating the clamp into pneumatic systems. Practical benefits for workshop and production planners Specification-driven data—arm length, angle, material and rated forces—translates directly into operational advantages: shorter setup times, improved throughput and lower rework rates. The galvanised body and sturdy lever design reduce service downtime and extend replacement intervals, which improves total cost of ownership for fixture fleets. When selection or integration questions arise, product documentation and technical codes allow straightforward comparison with existing clamps and ensure coherent fixture planning across multiple lines. Discuss fixture requirements and specify the Kukamet 651 with Metav Werkzeuge to ensure optimal clamping performance in your production set-up Technical data Article number: 651-4-D-C1 Manufacturer: Kukamet Model: 651 Brand: Kukamet Material: Galvanised Mounting: Vertical base Facts Arm length: 100 mm Angle: 90° Max pressing force: 3,000 N Max holding force: 3,300 N eClass: 21021004 ETIM: EC011973 Special features Massive holding arm Lever clamp design Galvanised finish Vertical base for stable mounting FAQ What clamping forces does this unit provide? The Kukamet pneumatic clamp 651 delivers up to 3,300 N holding force and a maximum pressing force of 3,000 N, suitable for medium-duty fixture applications. Is the clamp suitable for outdoor or humid workshop conditions? The galvanised finish on the unit provides enhanced corrosion resistance, making it better suited to humid environments than uncoated alternatives. How is the clamp mounted to a fixture plate? Mounting is via a vertical base designed for stable attachment to fixture plates and modular assembly tables. Can the clamp be used in automated stations? Yes, the pneumatic actuation and repeatable stroke make the clamp appropriate for automated and semi-automated production lines. Does the clamp support 90° positioning only? The design provides a defined 90° clamping orientation; adaptations for other angles would require custom fixturing or adapters. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 108mm Horizontal Clamp Massive Holding Arm, 2.5kN Hold Force - Kukamet
Compact, robust and easy to integrate: the Kukamet Horizontal clamp 113 combines a massive holding arm, a compact 108 mm reach and a blackened finish to provide repeatable clamping up to 2,500 N; order the clamp directly via Metav Werkzeuge or consult their specialists for fixture integration. Kukamet Horizontal clamp 113 – horizontal lever clamp with angle foot mounting and heavy-duty arm The Horizontal clamp 113 is a horizontal lever clamp designed for jigs, fixtures and general workshop applications where strong, repeatable clamping at a right angle is required Heavy-duty holding arm for stable clamping Angle foot mounting for secure installation 2,500 N maximum holding force Compact 108 mm arm reach for tight setups Blackened finish for workshop resilience Consistent, high-force clamping for reliable production A robust clamp construction ensures consistent clamping with a maximum holding force of 2,500 N and a maximum clamping force of 2,300 N. The combination of a massive holding arm and compact design reduces elastic deformation under load, improving repeatability in fixture work. This makes the component particularly suitable for mechanical assembly, welding jigs and machining fixtures where a stable, right‑angle hold is essential. Technical figures like force values and arm reach enable straightforward planning for fixture safety factors and cycle reliability. Space-efficient mounting and durable surface for workshop use The integrated angle foot mounting lets the clamp be mounted close to the workpiece, saving valuable fixture space and enabling low-profile layouts. The blackened finish offers increased resistance to surface wear and a discreet appearance that suits industrial environments. With a compact mass of 0.414 kg and a 108 mm arm length, the unit is easy to position on pallets and plates without adding unnecessary bulk, while the sturdy mounting connection keeps the clamping plane fixed at 90° during repeated cycles. Easy integration into existing tooling and long-term operation Designed as a straightforward mechanical solution, this lever clamp fits conventional fixture patterns and can be combined with locating pins, stops and other clamping elements. The compact footprint and well-defined mechanical data simplify fixture design and allow predictable energy distribution across the clamping system. For production environments seeking durability and predictable behaviour, the clamp supports long service intervals with basic inspection and lubrication rather than extensive upkeep, reducing downtime and maintenance overhead. For reliable, high-force clamping from a trusted brand, order the Kukamet Horizontal clamp 113 via Metav Werkzeuge for secure supply from Emmerich; contact info@metav-werkzeuge.com or call +49 2822 7131930 for technical advice and order coordination Technical data Article number: B113-3-D-C2 GTIN: 8680731507461 eClass: 21041719 ETIM: EC011973 Facts Arm length: 108 mm Angle: 90° Holding force: 2,500 N Clamping force: 2,300 N Weight: 0.414 kg Special features Mounting: angle foot mounting Massive holding arm Finish: blackened finish Category: Spanner Manufacturer: Kukamet FAQ What is the maximum holding force of the clamp? The Kukamet Horizontal clamp 113 delivers a maximum holding force of 2,500 N and a clamping force of 2,300 N. Can this clamp be mounted on a fixture plate at low profile? Yes, the angle foot mounting is intended for secure, space-saving installation close to the workpiece. Is the arm suitable for repetitive production cycles? The heavy-duty arm and robust construction of this lever clamp are designed for repeated clamping operations with predictable repeatability. Which surface treatment does the clamp have? The unit is supplied with a blackened finish, offering improved surface resilience for workshop environments. What size reach does the clamp provide? The compact arm reach is 108 mm, allowing use in tight fixturing situations without excessive overhang. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 108mm Horizontal Clamp With Massive Holding Arm And Safety Lock, 2.5kN Clamping Force - Kukamet
Combine robust galvanised construction with a 2,500 N holding capacity and a compact 90° mounting for reliable, space-saving fixturing; order the horizontal clamp directly via Metav Werkzeuge or consult our advisors if further specification is required. Horizontal Clamp 113 — Kukamet lever clamp with 108 mm arm and safety lock The Horizontal Clamp 113 is a lever-operated horizontal clamp with an angled foot, engineered for secure fixture work in jigs, assembly and repetitive production tasks. Galvanised steel body for corrosion resistance 108 mm heavy-duty holding arm 2,500 N maximum holding force 90° angled foot with safety locking mechanism Consistent clamping force for repeatable results The clamp delivers a 2,500 N maximum holding capacity combined with a robust 108 mm holding arm, providing consistent force across repeated cycles. This lever clamp design converts simple manual actuation into reliable clamping pressure, reducing variability in production runs. The result is fewer rework steps and a measurable improvement in process stability when used in fixtures and assembly jigs where constant force matters. Fits tight layouts and supports flexible mounting A 90° angled foot enables edge-mounted installation on plates and frames, saving workspace and improving tool accessibility. At approximately 0.42 kg, the unit is light enough for compact fixtures yet substantial enough to remain stable during operation. The angled attachment prevents interference with adjacent components and allows integration into modular tooling systems without complex adapters or extensive modification. Durable construction that lowers maintenance requirements Constructed from galvanised steel with a massive holding arm, the clamp resists corrosion and mechanical wear in workshop environments. The integrated safety lock secures the lever in the clamped position, preventing accidental release during handling or vibration-prone processes. These features reduce downtime for upkeep and inspection, delivering longer service intervals and predictable lifecycle performance in everyday industrial use. Streamlines assembly while offering simple adjustment As a compact, toggle-style fixture, this clamp speeds up manual cycle times and simplifies workholding setup. The combination of quick lever action and positive locking provides immediate tactile feedback, which helps operators maintain uniform clamping across batch work. For bespoke fixtures or series production the clamp suits welding, finishing and inspection stations where fast, repeatable operation is required. If clarification on selection or integration is needed, Metav’s technical advisors can provide specification guidance and compatibility checks. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet Horizontal Clamp 113 into production jigs — our Emmerich team will advise on mounting options and delivery: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data Article number: 113-3-D-L-C2 GTIN: 8680731500875 Manufacturer: Kukamet Facts Arm length: 108 mm Weight: 0.42 kg Holding force: 2,500 N Maximum pressing force: 2,300 N Angle: 90° Special features Material: Galvanised Mounting: Angled foot (Winkelfuß) Massive holding arm and safety locking mechanism Category: Spanners eClass: 21041719 ETIM: EC011973 FAQ What holding force does the clamp provide? The clamp provides a maximum holding force of 2,500 N, suitable for secure fixture tasks in assembly and jig applications. How is the clamp mounted? Mounting is via an angled foot at 90°, allowing edge installation on plates and fixture frames for compact layouts. Is the clamp suitable for workshop environments with moisture? Yes, the galvanised finish protects the clamp against corrosion, improving durability in workshop conditions. What are the key dimensions to consider for fixture design? Important values are the 108 mm arm length and the overall weight of 0.42 kg; these determine reach and balance in the fixture. Does the clamp include a locking feature for safety? A mechanical safety lock secures the lever in the clamped position to prevent accidental release during operation. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 110mm Horizontal Clamp With Massive Holding Arm And Safety Lock, 1 200N Hold Force - Kukamet
Take advantage of a compact, corrosion‑resistant clamping solution that combines a massive holding arm, a safety lock and a 110 mm lever for reliable fixturing; order the clamp directly via Metav Werkzeuge or consult our specialists if specification guidance is required. Horizontal clamp 113 — horizontal lever clamp with 110 mm arm, galvanised finish (Kukamet) The Horizontal clamp 113 is a right‑angle lever clamp designed for secure, repeatable clamping in workshop and light industrial fixturing applications Robust holding arm with safety lock Galvanised finish for corrosion resistance 110 mm lever arm for extended reach 1,200 N maximum hold capacity Secure, repeatable clamping for production use The 113 is built as a toggle clamp for consistent repeatability in fixture setups. The combination of a massive holding arm and an integrated safety lock reduces the risk of accidental release during machining or assembly, converting manual leverage into stable holding force. With a clearly defined maximum pressing force and a separate holding capacity, the clamp enables precise selection of fixturing components for repeat processes. For production environments where cycle consistency matters, the mechanical simplicity of the design minimises maintenance requirements while maintaining high functional reliability. Fit and functionality for workshop and jigs A galvanised finish protects the clamp against corrosion, making the unit suitable for workshop benches and moderate ambient humidity. The 110 mm arm provides extra reach when working on fixtures where clearance is limited, and the right‑angle orientation supports fixtures that require perpendicular clamping. The compact mass and modest weight allow straightforward retrofitting to existing jigs and tooling boards without compromising rigidity. Where a compact footprint and dependable clamping are required, this lever clamp offers a pragmatic balance between holding capability and ease of integration. Installation, durability and operational benefits Mounting is via an angled base that secures the clamp at a fixed 90° orientation, simplifying alignment during installation and ensuring consistent clamping geometry. The galvanised material finish contributes to long‑term durability under typical workshop conditions, while the mechanical safety lock adds a layer of operational security during handling and transfer. The robust mechanical design reduces the need for frequent adjustments and supports uninterrupted workflows, helping to lower downtime and keep small‑batch or series production running smoothly. Discuss the suitability of the Kukamet 113 horizontal clamp with Metav Werkzeuge — for specification advice and supply from Emmerich please contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 113-2-D-L-C2 GTIN: 8680731500790 Model: 113 Brand: Kukamet Core specifications Arm length: 110 mm Angle: 90° Max pressing force: 1,000 N Max holding capacity: 1,200 N Weight: 0.27 kg Materials and special features Material: galvanised steel Mounting type: angled base (Winkelfuß) Massive holding arm Safety lock Right‑angle lever (toggle) clamp FAQ What maximum holding force can be expected from this clamp? The Horizontal clamp 113 (Kukamet, SKU 113-2-D-L-C2) specifies a maximum holding capacity of 1,200 N and a maximum pressing force of 1,000 N, which should be considered when designing fixtures. Is the clamp suitable for use in a humid workshop environment? The galvanised steel finish on the 113 provides corrosion resistance suitable for typical workshop conditions, extending service life compared with untreated components. How is the clamp mounted and aligned on a fixture? The unit mounts via an angled base at a fixed 90° orientation; this simplifies alignment and ensures consistent clamping geometry for repeatable assembly or machining operations. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 110mm Horizontal Clamp With Massive Holding Arm, 1,200N Clamp Force - Kukamet
Combining a massive 110 mm holding arm, galvanised construction and up to 1,200 N holding force, this clamp secures workpieces at 90° for reliable production routines; order the clamp directly via Metav Werkzeuge or request advice from our consultants to confirm suitability for the application. Horizontal Clamp 113 — Kukamet angled-base clamp with 110 mm arm A robust Horizontal Clamp 113 for repeatable 90° clamping in jigs and fixtures, featuring a massive galvanised holding arm and an angled base for stable mounting Massive 110 mm holding arm Galvanised construction for corrosion resistance 1,200 N maximum holding force Angled base for stable 90° mounting Reliable right‑angle clamping for fixtures and jigs The design centres on consistently reproducible 90° positioning, enabled by a solid 110 mm arm and a compact body that keeps the clamping point stable under load. Measured performance figures—1,200 N holding force and 1,000 N pressing force—provide a clear basis for selecting the clamp for light to medium production tasks. The compact build and specified forces allow engineers and workshop planners to calculate clamping layouts and safety margins with confidence. Lever-action mechanism for fast, repeatable operation A lever-based actuation delivers quick engagement and release while maintaining clamping integrity. The lever action converts manual input into secure clamping without complex adjustments, making cycle times predictable in assembly processes. The difference between holding and pressing forces is explained by the mechanism geometry: the holding force denotes resistance to part movement, while the pressing force indicates the clamp’s direct contact pressure—both metrics assist process engineers in tooling decisions. Space-saving angled mounting that cuts setup time The angled base allows installation directly on vertical or horizontal fixture plates, reducing the need for additional brackets. Its 90° orientation and compact footprint support denser tooling layouts on fixture plates and welding jigs. The clamp’s low mass and small profile permit multiple clamps to be installed in close succession, enabling efficient workpiece locating and secure fixation without excessive added weight to tooling assemblies. Corrosion-resistant finish for workshop durability Constructed in galvanised steel, the clamp resists surface corrosion common in workshop environments, extending service intervals and reducing replacement cycles. The massive holding arm is dimensioned for long-term rigidity, limiting deformation under repeated loads and thereby preserving clamping accuracy. The finish also simplifies maintenance routines: occasional cleaning and inspection are typically sufficient to retain dependable operation. Practical suitability and planning advantages The clamp suits applications where a predictable manual clamp with a robust arm is required—examples include assembly, light welding jigs and general fixture work. Its measurable specifications make it straightforward to integrate into bills of materials and technical layouts, supporting procurement and production planning alike. The combination of compact form, clear force ratings and corrosion protection supports consistent throughput and reduces uncertainty in everyday shopfloor use. For reliable right‑angle clamping from Kukamet, contact Metav Werkzeuge for ordering and technical clarification — telephone +49 2822 7131930 or eMail info@metav-werkzeuge.com — and benefit from Metav’s workshop expertise and fast supply from Emmerich. Technical data SKU: 113-2-D-C2 GTIN: 8680731500769 Manufacturer: Kukamet Core specifications Arm length: 110 mm Angle: 90° Max holding force: 1,200 N Max pressing force: 1,000 N Weight: 0.282 kg Materials & features Galvanised steel construction Massive holding arm Angled base (Winkelfuß) Lever clamp design FAQ What is the maximum holding force of the clamp? The Kukamet Horizontal Clamp 113 provides a maximum holding force of 1,200 N, a specification intended to help determine suitability for fixture and jig applications. How much pressing force does the clamp deliver at the contact point? The clamp delivers up to 1,000 N pressing force at the contact surface; this value indicates the clamp’s contact pressure for securing workpieces. Can the clamp be mounted for vertical or horizontal clamping planes? Yes, the angled base enables mounting on plates to achieve secure 90° clamping, suitable for both vertical and horizontal fixture orientations. What finish protects the clamp in workshop environments? The clamp is galvanised, offering corrosion resistance to extend service life under typical workshop conditions. Is the clamp suitable for dense fixture layouts where space is limited? The compact design, combined with a 110 mm arm and low mass, supports close‑packed installations on fixture plates for efficient tooling arrangements. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 110mm Horizontal Clamp With Massive Holding Arm, Safety Lock, 1 200N Hold Force - Kukamet
Take advantage of the combination of a heavy-duty clamping arm, a reliable safety lock, and compact mounting to keep fixture setup fast and repeatable. Order the Horizontal clamp 113 directly via Metav Werkzeuge or ask our consultants if technical matching is required. Kukamet Horizontal clamp »113« – 90° angle-foot toggle clamp with 110 mm arm The Horizontal clamp 113 is a robust toggle clamp for fixture and jig applications, offering a 90° clamping orientation with an angled mounting foot for compact, secure installation Heavy-duty clamping arm with safety lock 90° horizontal clamp with 110 mm arm Blackened finish for corrosion resistance Closing force 1,000 N · holding force 1,200 N Secure, repeatable clamping to reduce setup time The heavy-duty construction and integrated safety lock ensure that workpieces remain clamped without accidental release, which lowers rework and improves throughput on repetitive operations. The lock engages positively when the handle is closed, providing a consistent clamping position for batch production. This mechanical reliability supports efficient fixture cycles and contributes to predictable process quality. Compact mounting that fits tight fixtures and jigs Designed with an angle foot and a 110 mm arm, this toggle clamp offers reach while keeping the mounting footprint small. The 90° orientation is suited to side-loading and edge-clamping tasks in assembly, machining preparation and inspection fixtures. With a low mass of approximately 0.27 kg, the unit integrates easily into modular tooling systems where minimised inertia and quick manipulation are beneficial. Robust performance and corrosion-resistant finish With a closing force of 1,000 N and a holding force of 1,200 N, the clamp secures medium-sized components reliably for downstream processing. The blackened finish provides enhanced resistance to surface corrosion and reduces the need for frequent maintenance, extending service life in workshop environments. Built for sustained use, the clamp balances force capacity with compact dimensions to support dependable production performance. Arrange a technical consultation with Metav Werkzeuge to specify the Kukamet Horizontal clamp 113 for fixture integration and ensure fast, reliable supply from Emmerich Technical data Article number: B113-2-D-L-C2 Manufacturer: Kukamet Model: 113 Core specifications Arm length: 110 mm Clamping angle: 90° Closing force: 1,000 N Holding force: 1,200 N Weight: 0.27 kg eClass: 21041719 ETIM: EC011973 Special features Angle foot mounting Robust clamping arm Safety locking mechanism Blackened finish (Schwarz brüniert) Suitable as a lever/toggle clamp SKU: B113-2-D-L-C2 FAQ What clamping forces are provided by this clamp? The Kukamet Horizontal clamp 113 delivers a closing force of 1,000 N and a holding force of 1,200 N, suitable for securing medium-sized components in fixtures. Can the clamp be fixed to a fixture plate with an angled mounting? Yes, the clamp uses an angle foot for 90° mounting, allowing secure attachment to plates and frames in compact jig designs. Is the surface finish suitable for workshop environments? The blackened finish on the Horizontal clamp 113 provides increased resistance to corrosion and wear, reducing maintenance intervals in standard workshop conditions. For which applications is this toggle clamp most suitable? This toggle clamp is intended for assembly fixtures, inspection jigs and general workshop clamping tasks where a compact, reliable horizontal hold is required. What are the dimensions relevant to fixture planning? Key dimensions for planning are a 110 mm arm length and a 90° clamping orientation; refer to technical drawings for exact mounting-hole positions Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 111 Horizontal Clamp With Massive 116mm Holding Arm, 1,200 N Grip, Galvanised - Kukamet
Take advantage of the combination of robust clamping force, compact dimensions and a corrosion‑resistant finish for reliable fixture performance; order the clamp directly via Metav Werkzeuge or ask our consultants if needed. Horizontal clamp 111 by Kukamet — solid holding arm, 90° mounting A Horizontal clamp 111 designed for secure right‑angle clamping in jigs and fixtures, offering a compact 116 mm arm and a galvanised finish for workshop durability. Solid holding arm for robust clamping 116 mm holding arm length Galvanised finish for corrosion resistance 90° mounting with horizontal foot Consistent clamping performance that keeps production steady The clamp delivers measurable, repeatable results: a maximum holding force of 1200 N and a thrust capability of 1000 N ensure secure fixation of components during machining and assembly. The solid holding arm reduces flex under load, which helps to maintain part position and reduces rework. For production engineers and fixture designers, this means fewer interruptions and a predictable process window. Technical terms: holding force denotes the static retention capability, while thrust indicates the applied clamping force during engagement. Compact footprint with practical mounting for fixtures With an arm length of 116 mm and a 90° mounting angle, the clamp fits into confined jig layouts without compromising accessibility. The horizontal foot mounting allows the component to sit flush with fixture plates, simplifying alignment and saving valuable bench or machine table space. At a weight of only 0.23 kg, the clamp is easy to position during assembly and contributes minimally to the overall fixture mass, which can be important when tool balance or handling is considered. Durable construction for long service life in workshops Constructed from galvanised steel, the device resists corrosion in everyday workshop environments, reducing maintenance intervals and replacement cycles. The robust design and materials support long‑term reliability, which is particularly relevant for small series production or maintenance departments seeking a durable and cost‑effective clamping solution. The clamp is suitable for integration into standard fixture plates and can be combined with other clamping elements to build modular, adaptable tooling. Choose Kukamet’s 111 horizontal clamp for dependable right‑angle clamping and contact Metav Werkzeuge for supply and technical advice. Technical Data SKU: 111-2-D-C2 GTIN: 8680731500073 eClass: 21041719 ETIM: EC011973 Facts Arm length: 116 mm Weight: 0.23 kg Angle: 90° Maximum holding force: 1200 N Maximum thrust force: 1000 N Special features Material: galvanised steel Mounting: horizontal foot Design feature: solid holding arm Category: clamps Manufacturer: Kukamet FAQ What materials can the Horizontal clamp 111 be used on? The Horizontal clamp 111 is intended for general clamping in fixture and jig applications; material suitability depends on the workpiece and fixture design rather than the clamp itself. What is the maximum clamping force of this clamp? The clamp provides a maximum holding force of 1200 N and a thrust capability of 1000 N, giving secure retention for most light to medium production tasks. How is the clamp mounted in a fixture? The unit uses a horizontal foot for 90° mounting; it is designed to sit flush on fixture plates for straightforward alignment and secure attachment. Is the finish suitable for humid workshop environments? The galvanised finish offers corrosion resistance suitable for standard workshop conditions, extending service life and reducing maintenance. Does the clamp require frequent maintenance? Due to its robust construction and galvanised surface, regular maintenance is minimal; periodic inspection for wear and lubrication of moving joints is recommended. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 111 Horizontal Clamp With Safety Lock, 2.5 kN Holding Force, Blackened Finish - Kukamet
Benefit from a compact, high-performance clamp with a 2,500 N holding force and an integrated safety lock for consistent, secure workholding; the M8x50 pressure spindle and horizontal base ensure fast mounting and reliable repeatability. Order the (Horizontal toggle clamp 111) directly via (Metav Werkzeuge) or ask our consultants if needed. Horizontal toggle clamp 111 — horizontal base, integrated safety lock (Kukamet) Horizontal toggle clamp 111 is a robust lever clamp designed for horizontal mounting in jigs, fixtures and assembly benches where secure, repeatable clamping is essential. Horizontal base for stable mounting Integrated safety lock for secure clamping Max. holding force 2,500 N Pressure spindle M8x50 included Keep production running with consistent clamping power The clamp delivers a combination of 2,300 N clamping force and 2,500 N holding force, providing strong, repeatable restraint for manual and semi-automatic operations. Expressed in practical terms, the holding force equates to roughly 255 kgf, which helps prevent component movement during machining, welding or assembly. The robust force ratings reduce the need for frequent re-positioning, lowering cycle times and cutting the risk of rejects. The result is an efficient workholding component that supports steady throughput and reliable fixture performance. Safety features that protect parts and personnel An integrated safety lock prevents accidental release of the lever and secures the clamped workpiece during pauses or handling. The clamp’s 90° locking angle provides a clear mechanical stop, making engagement and disengagement predictable for operators. This design reduces incidental loosening under vibration and contributes to a safer bench environment, particularly when used in repetitive processes. The locking mechanism is mechanical and visible, offering instant confirmation that the workpiece remains secure without electronic aids. Compact format for simple integration into existing tooling With a horizontal mounting foot and a light overall mass of 0.34 kg, the device is easy to fit into existing fixtures, rails or custom jigs without adding excessive bulk. The included M8x50 pressure spindle allows adjustable contact pressure and compensation for part-height variance, enabling precise set-up in confined spaces. The low profile and modest footprint make it suitable for tight assemblies and transfer systems where space and weight are critical considerations, while still delivering industrial-level clamping performance. Practical applications and finish for workshop use Engineered as a lever-style workholding element, the clamp is ideal for assembly benches, inspection fixtures and clamping points on manual or semi-automated tooling. The blackened finish provides a durable, low-reflective surface that integrates well into professional workshop environments and helps to mask surface wear. The mechanical simplicity supports quick maintenance and long service life, making the component a pragmatic choice for workshops seeking dependable, low-complexity clamping solutions. For technical advice on integrating the Kukamet 111 into fixtures or to request dimensions and mounting recommendations, contact Metav Werkzeuge at +49 2822 7131930 or info@metav-werkzeuge.com — Metav’s specialists will assist with application guidance and suitability checks Technical data SKU: B111-3-L GTIN: 8680731507027 Article name: Horizontal toggle clamp 111 Manufacturer: Kukamet Facts Max. clamping force: 2,300 N Max. holding force: 2,500 N Clamping angle: 90° Weight: 0.34 kg Pressure spindle: M8x50 Special features Horizontal base (waagerechter Fuß) Safety lock present Blackened finish (Schwarz brüniert) Lever-style clamp (hebelspanner) ECLASS: 21041719 ETIM: EC011973 FAQ What clamping and holding forces does the clamp provide? The Kukamet Horizontal toggle clamp 111 delivers a clamping force of 2,300 N and a maximum holding force of 2,500 N, suitable for robust manual and semi-automatic workholding. Does the clamp include a safety device to prevent accidental release? Yes — the clamp features an integrated safety lock that secures the lever in the engaged position to reduce the risk of accidental opening during handling. How is the clamp mounted and what spindle is supplied? Mounting is via a horizontal foot and the unit is supplied with an M8x50 pressure spindle for adjustable contact pressure and compensation for part tolerances. Is the clamp suitable for tight or compact fixtures? The device’s low weight (0.34 kg) and horizontal base make it well suited to compact fixtures, assembly benches and narrow tooling spaces. What surface finish does the clamp have? The clamp is supplied with a blackened finish, offering a professional, low-reflective appearance and corrosion-resistant surface treatment. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 111 Horizontal Clamp With Safety Lock, Stainless Steel, 2.3 kN Hold Force - Kukamet
The compact stainless steel horizontal clamp combines a secure 2,500 N holding force, adjustable pressure via an M8x50 pressure spindle and an integrated safety lock to keep fixtures stable and operators safe. Order the horizontal clamp directly via Metav Werkzeuge or ask our consultants if needed. 111 Horizontal clamp (S111-3-L) by Kukamet — stainless steel, safety lock The 111 horizontal clamp is a compact stainless steel toggle clamp for secure workholding in jigs and fixtures, designed for horizontal mounting and repeatable production clamping. *Stainless steel construction *Safety locking mechanism *2,500 N holding force *Horizontal base for stable mounting Durable stainless steel body for long service life The clamp's stainless steel construction delivers corrosion resistance and high wear tolerance, ensuring consistent performance in workshop and light industrial environments. A robust material choice reduces replacement frequency and supports continuous production, while the compact design keeps the overall fixture footprint small. This combination of durability and space efficiency helps to maintain throughput without sacrificing reliability. Measurable clamping and holding performance for stable machining Designed to provide precise workholding, the unit offers a clamping force of 2,300 N and a holding force of 2,500 N, values that translate directly into stable fixturing during machining and assembly operations. The M8x50 pressure spindle allows fine adjustment of clamping pressure and compensates for small part tolerances, improving repeatability and reducing the need for rework. These quantifiable specifications make the clamp suitable for repeat production runs where consistent clamping is essential. Safety and mounting that support efficient workflows Fitted with an integrated safety lock, the clamp prevents accidental release and secures the toggle in the closed position, enhancing operator safety and process reliability. The horizontal base (waagerechter Fuß) and a 90° lever angle provide straightforward installation into benches, plates or fixture plates, enabling rapid integration into existing jigs. At only 0.34 kg, the component is easy to handle during assembly yet substantial enough to withstand production use. Low-maintenance design that keeps machines running With a simple mechanical design and corrosion-resistant materials, maintenance requirements are minimal: periodic inspection and light lubrication are typically sufficient. The compact toggle mechanism minimises moving-part exposure and reduces the risk of contamination affecting function. For customers seeking dependable, low-intervention clamping, this clamp supports reduced downtime and predictable handling in daily production. Choose Kukamet quality with the S111-3-L horizontal clamp — contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich. Technical data Article number: S111-3-L GTIN: 8680731508901 Manufacturer: Kukamet Core specifications Weight: 0.34 kg Holding force max: 2,500 N Clamping force max: 2,300 N Pressure spindle: M8x50 Angle: 90° Features and versions Material: Stainless steel Mounting: horizontal base Safety lock: yes ECLASS: 21041719 ETIM: EC011973 FAQ What materials is the clamp suitable for? The Kukamet horizontal clamp S111-3-L is a general-purpose toggle clamp with a stainless steel body; suitability for specific materials depends on the workpiece and process rather than the clamp itself. How is the clamping pressure adjusted? Adjustment is by the M8x50 pressure spindle, which permits fine tuning of the contact pressure to accommodate part tolerances and improve repeatability with the S111-3-L. Does the clamp lock in the closed position? Yes, the unit features an integrated safety lock that secures the toggle in the closed position to prevent accidental release and to enhance operator safety. Can the clamp be mounted on fixture plates? The clamp is designed for a horizontal base mounting and a 90° lever angle, making it suitable for installation on fixture plates, benches and jigs in production settings. What are the measurable forces for selection? Key values are a clamping force of 2,300 N and a holding force of 2,500 N, which allow accurate assessment for workholding requirements with the S111-3-L. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 111 Horizontal Clamp With Safety Lock, Zinc Plated, 4.5 kN Closing Force / 5 kN Holding Force - Kukamet
Benefit from robust galvanised construction, a positive safety lock and reliable holding capacity to secure fixtures with minimal downtime; order the horizontal clamp directly via Metav Werkzeuge or consult the company’s specialists if required. Horizontal clamp 111 – galvanised lever clamp with safety lock (Kukamet) The Horizontal clamp 111 is a compact 90° lever clamp designed for secure, repeatable workholding on machining and assembly fixtures, suited to integration where a horizontal base is required. Galvanised steel construction Safety lock for secure clamping Horizontal base for fixed mounting 5,000 N holding force Stable, repeatable clamping that reduces setup variance The galvanised lever device delivers a 5,000 N holding force combined with a maximum clamping thrust of 4,500 N, offering a reliable margin between holding and actuation. This performance ensures consistent part retention under machining loads and reduces the frequency of manual re-adjustment; the positive safety lock maintains clamping position during secondary operations, lowering the risk of accidental release. By converting mechanical input into secure workholding, the unit supports higher process repeatability and predictable cycle outcomes. Durable construction engineered for workshop environments A corrosion-resistant galvanised finish and robust steel construction provide long service life in industrial environments. The clamping spindle is specified as M12x80, allowing straightforward replacement or integration with standard fixture hardware. With a compact mass of 1.52 kg the clamp combines rigidity with low bulk, making it suitable for tight assemblies where space is at a premium. The 90° lever orientation yields a low-profile footprint while maintaining mechanical advantage for swift actuation. Straightforward mounting and flexible fixture integration Configured with a horizontal base, the clamp is intended for secure bolting to plates and tooling blocks, facilitating rapid installation into existing jigs or welding tables. The lever-style mechanism enables fast manual operation and simple visual confirmation of engagement, supporting efficient fixture changeovers and short setup times. As a lever clamp the device is well suited to repetitive production tasks and smaller batch runs where reliable, fast clamping is required. The combination of compact design and robust holding characteristics makes this model a practical choice for general workshop and light production use. For specification matching or a tailored quotation, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: 111-5-L GTIN: 8680731500370 Brand: Kukamet Category: Spanner Facts Holding force: 5,000 N Max clamping force: 4,500 N Weight: 1.52 kg Angle: 90° Spindle thread: M12x80 Design & features Material: galvanised Mounting: horizontal base (waagerechter Fuß) Safety lock: present Clamping type: lever clamp FAQ What clamping and holding capacities does the Horizontal clamp 111 provide? The Kukamet Horizontal clamp 111 (SKU 111-5-L) offers a maximum clamping thrust of 4,500 N and a holding force of 5,000 N for secure fixturing during machining and secondary operations. Is the clamp suitable for use in humid or workshop environments? Yes, the Horizontal clamp 111 features a galvanised finish that improves corrosion resistance, making the Kukamet horizontal clamp appropriate for general workshop and light industrial settings. How is the clamp mounted to a fixture or table? The clamp uses a horizontal base for fixed bolting to plates or tooling blocks; the design supports straightforward integration into existing fixtures and welding tables. What spindle connection does the clamping spindle use? The clamping spindle is specified as M12x80, allowing compatibility with standard fastening components and facilitating replacement or adjustment. Does the device include a mechanism to prevent accidental release during operations? Yes, the Kukamet horizontal clamp 111 is equipped with a positive safety lock that secures the lever in the clamped position and reduces the risk of unintended opening. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp Heavy-Duty Arm Vertical Base 2.5 kN Hold Force Galvanised - Kukamet
Take advantage of a robust, galvanised construction and a massive holding arm to secure workpieces reliably; combine this with a compact vertical-foot mount and a holding force of up to 2,500 N for steady production processes. Order the clamp directly via Metav Werkzeuge or contact our consultants for specification advice. Horizontal clamp 112 — Kukamet lever toggle clamp with 2,500 N holding force Horizontal clamp 112 is a lever-type toggle clamp designed for fastening workpieces in fixtures and jigs, offering a compact mounting footprint and workshop-grade durability. Galvanised steel construction 118 mm arm length for versatile reach Holding force up to 2,500 N Vertical-foot mount for secure installation Secure clamping that speeds up throughput The clamp delivers a clear mechanical advantage through a lever toggle design, providing a holding force of 2,500 N and a maximum pressing force of 2,300 N. These figures translate into reliable retention of components during machining, welding or assembly, reducing part movement and minimising rework. The term holding force here refers to the clamping capacity that resists displacement under load; expressed in newtons, it is a comparable, objective indicator of performance. Integrating this clamp into production fixtures supports repeatable results and shorter cycle times thanks to fast actuation and robust contact pressure. Compact, corrosion-resistant design for workshop environments With a galvanised finish and a massive holding arm, the clamp resists surface corrosion while providing torsional stability under load. The 118 mm arm length offers a balance between reach and compactness, allowing fixtures to remain slim without compromising clamping leverage. The vertical foot mounting suits bench plates and welded fixtures, and the 90° orientation ensures predictable positioning of the clamped part. These design choices mean longer service intervals and fewer replacements, which is particularly valuable where tool changeover costs and downtime must be kept low. Practical supply and integration for professional users Supplied by Kukamet and available through Metav Werkzeuge, this lever toggle clamp fits workshop and industrial settings where dependable mechanical clamping is needed. The clamp’s straightforward geometry simplifies integration into jigs, pallet systems and welded frames; fixing points and orientation are standardised for rapid installation. Metav’s role as a central supplier provides access to stock, technical information and ordering from Emmerich, with the benefit of consolidated sourcing for measurement and clamping systems. The combination of robust clamping, corrosion protection and supply reliability supports consistent quality across production runs. Request a tailored quote from Metav Werkzeuge for the Kukamet Horizontal clamp 112, specifying required clamping configuration and mounting preference — phone +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: 112-3-D-C2 GTIN: 8680731500509 Manufacturer: Kukamet Numbers / Core technical data Arm length: 118 mm Weight: 0.326 kg Holding force (max): 2,500 N Pressing force (max): 2,300 N Angle: 90° Design / Special features Material: galvanised steel Mounting: vertical foot Massive holding arm Type: lever toggle clamp FAQ What holding and pressing forces does the clamp provide? The Horizontal clamp 112 (Kukamet, SKU 112-3-D-C2) offers a holding force of up to 2,500 N and a pressing force of up to 2,300 N for secure retention under load. What is the clamp made from and how resistant is it to corrosion? The clamp is made from galvanised steel, which provides a protective zinc finish for improved resistance to rust in workshop conditions. How is the clamp mounted and what orientation does it have? Mounting is via a vertical foot, with the clamp designed to operate at a 90° orientation suitable for bench plates and welded fixture assemblies. Which applications suit this lever toggle clamp? The clamp is appropriate for fixture work, assembly jigs, welding fixtures and general workshop clamping tasks where a compact, strong toggle clamp is required. What is the reach of the clamping arm? The clamping arm measures 118 mm, offering practical reach for a wide range of component sizes. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp Heavy-Duty Holding Arm, 2.5 kN Holding Force, Galvanised - Kukamet
Combine the galvanised construction, massive holding arm and 90° lever action for reliable, repeatable clamping; order the 112 horizontal clamp via Metav Werkzeuge or consult their specialists for procurement and application advice. 112 Horizontal Clamp — Kukamet lever clamp with 90° action and 168 mm arm The 112 horizontal clamp is a galvanised lever clamping device designed for fixed-angle holding in workshop, jig and assembly applications Massive holding arm for stable clamping Galvanised finish for corrosion resistance 90° lever action for secure positioning 168 mm arm reach for deep fixtures Faster, more reliable clamping for production workflows The lever-style design delivers a high clamping force with compact movement, turning manual operations into reproducible tasks. With a maximum clamping force of 2,300 N and a peak holding force of 2,500 N, the device secures workpieces reliably while reducing rework and downtime. The massive holding arm concentrates force where it is needed, improving stability in jigs and fixtures. This repeatability supports efficient batch work and helps maintain consistent part quality on assembly lines. Compact mounting and rapid operation for tight spaces Fitted with a vertical foot for simple installation, the clamp occupies minimal bench space while providing a robust anchoring point. The 168 mm arm reach allows engagement over deeper fixtures without compromising access, and the lever action enables quick open/close cycles that shorten handling times. At 0.354 kg, the unit is lightweight enough for retrofitting existing fixtures yet sturdy in operation. The combination of compact footprint and rapid actuation supports ergonomic handling and smoother process flows in small to medium workshops. Durable finish and low-maintenance service life Constructed from galvanised steel, the clamp resists corrosion in workshop environments, extending service intervals and lowering life-cycle costs. The simple mechanical design limits wear points and enables straightforward inspection; when regular checks are scheduled, the fixture retains accuracy for longer. Suitable for repetitive use in production and maintenance settings, the 112 is designed to integrate into existing tooling setups with minimal adjustment, delivering long-term reliability for demanding clamping tasks. Contact Metav Werkzeuge for a tailored quote or technical advice on integrating the 112 horizontal clamp into existing fixtures — Metav Werkzeuge provides specialist procurement and application support from Emmerich. Technical Data SKU: 112-3-D-C3 GTIN: 8680731500516 ECLASS: 21041719 ETIM: EC011973 Facts Weight: 0.354 kg Arm length: 168 mm Angle: 90° Max clamping force: 2,300 N Max holding force: 2,500 N Special features Material: galvanised Mounting: vertical foot Design: lever clamp Massive holding arm Category: clamp / fixture component FAQ What clamping and holding forces does the clamp provide? The 112 horizontal clamp offers a maximum clamping force of 2,300 N and a holding force of 2,500 N, suitable for robust fixture work in production environments. What material and finish are used for the clamp? The clamp is made from galvanised steel, giving the assembly enhanced resistance to corrosion and longer service life in workshop conditions. How is the clamp mounted and what space does it require? Mounting is via a vertical foot; the lever clamp is compact with a 168 mm arm reach and a weight of 0.354 kg, allowing integration into tight jigs and benches. Is the clamp suitable for repetitive production use? Yes — the lever action and massive holding arm deliver repeatable performance for batch production and jig applications, maintaining clamping consistency over many cycles. Which SKU identifies this product for ordering? Order reference is SKU 112-3-D-C3; the clamp is supplied by Kukamet and can be procured through Metav Werkzeuge for European distribution. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With 1,000 N Thrust, Massive Holding Arm, Galvanised - Kukamet
Benefit from a compact, high-performance clamp that combines a galvanised finish, a solid holding arm and reliable holding power for repeatable workshop tasks. Use the robust 166 mm reach and up to 1,200 N holding force to speed fixture setup — order via Metav Werkzeuge or contact their consultants for application advice. Horizontal clamp 112 by Kukamet — galvanised, 166 mm arm, 90° mounting A horizontal lever clamp designed for secure, repeatable fixing in jigs and fixtures across small-scale production and maintenance environments. Robust solid holding arm design 166 mm arm for versatile clamping reach Max holding force 1,200 N for secure fixing Vertical foot mounting at 90° for space-saving setup Reliable clamping performance for repetitive workflow The clamp delivers consistent mechanical performance via a lever-actuated mechanism that converts operator motion into secure locking force. With a maximum holding capacity of 1,200 N and a maximum clamping (pressing) force of 1,000 N, the device is suitable for repetitive clamping cycles where repeatability and safety matter. The compact reach of 166 mm gives flexibility in fixture layouts while the light overall mass supports quick repositioning of tooling. These measurable specifications allow planners to integrate the clamp into production cells with predictable outcomes. Compact mounting and ergonomic integration Engineered for a vertical foot installation at 90°, the clamp minimises footprint on benches and fixture plates, making it suitable for dense tooling arrangements and modular jigs. The 90° mounting orientation simplifies alignment with mating parts and reduces the need for additional brackets. Operation is straightforward thanks to the lever design, enabling rapid engagement and release during manual assembly or inspection steps. This combination of compact mounting and intuitive actuation improves throughput without compromising operator ergonomics. Durable material choice and workshop suitability Constructed in galvanised steel, the clamp resists corrosion in typical workshop atmospheres while keeping maintenance requirements low. The solid holding arm increases stiffness and wear resistance under lateral loads, supporting long service life even under frequent cycling. At 0.254 kg, the unit is light enough for easy handling yet engineered for secure fixation when mounted. Its practical design suits small-batch production, maintenance rigs and laboratory fixtures where dependable clamping and low upkeep are priorities. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet horizontal clamp 112 into existing fixtures or production lines — Metav Werkzeuge provides industry-grade guidance and rapid supply from Emmerich. Technical Data Article number: 112-2-D-C3 GTIN: 8680731500431 Brand: Kukamet Weight: 0.254 kg SKU: 112-2-D-C3 Facts Arm length: 166 mm Max holding force: 1,200 N Max clamping (pressing) force: 1,000 N Angle: 90° Special features Material: galvanised steel Mounting: vertical foot Design: lever clamp (horizontal) Feature: solid holding arm FAQ What clamping forces can be expected from this clamp? The Kukamet horizontal clamp 112 provides a maximum holding force of 1,200 N and a maximum clamping force of 1,000 N, enabling secure fixing for many workshop fixtures. Is the clamp suitable for compact fixture arrangements? Yes, the 90° vertical foot mounting and 166 mm arm make the clamp suitable for space-conscious installations and dense jig configurations. What material is the clamp made from and how does that affect maintenance? The clamp is made from galvanised steel; this finish reduces corrosion risk and lowers routine maintenance compared with untreated components. Can the clamp be used in high-cycle production environments? The lever mechanism and solid holding arm are designed for repeatable operation, making the clamp appropriate for repetitive manual or semi-automated clamping tasks in production or maintenance. Which product code should be referenced when ordering accessories or spare parts? Reference the article number / SKU 112-2-D-C3 and the Kukamet brand when enquiring about spare parts or compatible fittings. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With Massive Holding Arm And Safety Lock, 5 000 N Holding Force, Zinc-Plated - Kukamet
Take advantage of the combination of a massive holding arm, a secure safety lock and a zinc-plated finish for dependable, repeatable clamping in workshop fixtures; order the Horizontal clamp 112 directly via Metav Werkzeuge or ask our consultants if needed. Horizontal clamp 112 — Kukamet heavy-duty horizontal lever clamp with safety lock The Horizontal clamp 112 is a zinc-plated horizontal lever clamp designed for secure workholding and fixture use in workshops and light industrial jigs. Massive holding arm and safety lock Zinc-plated corrosion-resistant finish Holding force up to 5,000 N 179 mm reach with vertical base mount Consistent clamping performance that reduces rework The clamp delivers reliable clamping with a holding force of 5,000 N and a maximum clamping force of 4,500 N, values that support repeatable setups and reduced part movement during machining or assembly. The lever mechanism provides fast actuation and stable force transmission; this makes the device especially suitable for fixtures where cycle time and positional accuracy matter. Technical terms: "holding force" refers to the maximum static retention, while "clamping force" denotes the applied compressive force during closure. Built for workshop conditions and long service life Constructed from zinc-plated steel and equipped with a massive holding arm, the clamp resists corrosion and mechanical wear typical in busy shops. The vertical foot mounting simplifies fixture attachment and maintains a compact footprint on the workbench or jig plate. With a reach of 179 mm, the arm offers clearance for a wide range of components while the unit weight of 1.42 kg balances stability with ease of handling. Zinc plating is a sacrificial barrier that slows rust formation and prolongs component life. Safe, easy integration into existing fixtures A robust safety lock secures the lever in the clamped position, preventing accidental release during operation and enhancing operator safety. The clamp operates at a fixed 90° angle, facilitating standardised positioning in production fixtures. The lever action means rapid engagement and disengagement, reducing set-up time and increasing throughput in repetitive tasks. The compact design allows integration into bespoke jigs or modular fixture systems without complex modifications. Typical applications and practical benefits Designed as a horizontal lever clamp, the unit is well suited to workholding in assembly benches, inspection fixtures and light machining jigs. It supports tasks requiring repeatable positioning or quick part loading and unloading. The combination of a heavy-duty arm and safety locking mechanism offers confidence when clamping irregular or tall workpieces. Delivered through Metav’s European supply chain, the clamp benefits from local quality oversight and straightforward logistics for professional users. For secure, repeatable clamping choose the Kukamet Horizontal clamp 112 — contact Metav Werkzeuge for purchasing and detailed technical advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 112-5-D-L-C2 GTIN: 8680731500691 SKU: 112-5-D-L-C2 eClass: 21041719 ETIM: EC011973 Facts Weight: 1.42 kg Arm length: 179 mm Max clamping force: 4,500 N Max holding force: 5,000 N Angle: 90° Special features Material: Zinc-plated Mounting: Vertical foot Massive holding arm Safety lock Lever clamp type FAQ What clamping forces can be expected from the clamp? The Kukamet horizontal clamp 112 provides a maximum clamping force of 4,500 N and a holding force of up to 5,000 N for secure retention in fixtures. How is the clamp mounted to a fixture plate? Mounting is by the vertical foot, which allows the clamp to be bolted directly to a bench or jig plate for a compact installation. Is the clamp suitable for outdoor or humid workshop environments? The zinc-plated finish provides corrosion resistance that is appropriate for humid workshop conditions; periodic inspection and maintenance will extend service life. What safety features prevent accidental release? A dedicated safety lock secures the lever in the clamped position, preventing unintended opening during handling or machine operation. Can the clamp be used for quick-change fixturing and repeated cycles? Yes, the lever action and robust construction make it well suited to repeated engagement and fast part changes in production setups. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With Massive Holding Arm And Safety Lock, 66mm Reach, 1 000N Thrust - Kukamet
Take advantage of a compact, lever-operated horizontal clamp that combines robust holding power and a space-saving vertical base for dependable fixture work; order the clamp directly via Metav Werkzeuge or contact the consultants for clarification. Horizontal clamp 112 — lever clamp with 66 mm arm, 90° orientation (Kukamet) The 112 is a horizontal lever clamp engineered for fixture and workholding tasks, featuring a 90° arm and a vertical base for compact mounting in jigs and assembly stations. Massive holding arm with safety lock Vertical base for compact assembly 66 mm arm length for precise reach Holding force 1,200 N; clamping force 1,000 N Black oxide finish for corrosion resistance Consistent clamping performance for production use The lever-operated horizontal clamp delivers measurable holding and clamping capability: holding force 1,200 N and clamping force 1,000 N, values that define secure fixation under machining and assembly loads. The distinction between holding and clamping force is relevant for fixture planning: holding force indicates the static retention capacity, while clamping force denotes the direct pressure applied by the lever mechanism. These specifications support predictable cycle times and reduced rework in small-batch and repetitive production environments. Compact vertical mounting saves bench space Designed with a vertical base, the clamp enables installation on narrow fixture plates and tooling blocks without compromising reach. The 66 mm arm and 90° orientation provide a defined clearance envelope that simplifies layout planning in compact jigs. Vertical mounting reduces the footprint of the workholding setup and allows closer packing of clamps along a rail or plate, supporting efficient use of table space in crowded benches and automated cells. Robust construction for workshop reliability A massive holding arm and integrated safety lock ensure stable engagement and resistance to vibration during operation. The component’s black oxide finish offers practical corrosion resistance and a non-reflective surface for workshop environments. At approximately 0.2 kg, the unit balances low mass with mechanical resilience, making it suitable for frequent handling and retrofit use in existing fixtures without heavy additional load on tooling plates. Quick integration into fixtures and jigs The lever-action design facilitates fast clamping and unclamping to speed up workstation throughput while maintaining consistent pressure. The horizontal orientation and standardised dimensions make the clamp suitable for a wide range of fixture concepts, including manual jigs and semi-automated stations. The unit’s straightforward mechanics reduce maintenance effort and support uninterrupted operation in production and repair workshops; the clamp is particularly suited to tasks where reliable, repeatable fixation is required. Choose the Kukamet lever clamp via Metav Werkzeuge for dependable fixture clamping; contact Metav Werkzeuge for tailored advice or to confirm compatibility with existing tooling at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: B112-2-D-L-C1 Manufacturer: Kukamet SKU: B112-2-D-L-C1 Facts Arm length: 66 mm Angle: 90° Holding force: 1,200 N Clamping force: 1,000 N Weight: 0.2 kg Special features Vertical base (senkrechter Fuß) Massive holding arm Safety locking mechanism Black oxide finish (Schwarz brüniert) Lever-operated horizontal clamp FAQ What clamping and holding forces can be expected from this clamp? The clamp provides a clamping force of 1,000 N and a holding force of 1,200 N, values specified for the Kukamet horizontal clamp 112 to indicate safe fixation under typical workshop loads. Is the clamp suitable for compact fixture layouts? Yes, the vertical base and 66 mm arm make the unit well suited to tight layouts and close-packed clamping arrangements in jigs and small benches. Does the product include a safety feature to prevent accidental release? A built-in safety lock is integrated into the clamp design to secure the lever in the closed position and reduce the risk of unintended release during machining or handling. What surface treatment is applied to the clamp? The product features a black oxide finish, providing corrosion resistance and a matt surface ideal for workshop conditions. Can the clamp be used in manual and semi-automated stations? Yes, the lever-action mechanism and standard geometry allow straightforward use in manual jigs and many semi-automated fixturing systems. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With Massive Holding Arm And Safety Lock, 850 N Thrust, Galvanized - Kukamet
Take advantage of a compact, corrosion‑resistant clamp that combines robust holding capacity, a massive holding arm with safety locking, and straightforward vertical mounting for reliable fixture in repetitive production tasks; order directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Horizontal clamp 112 by Kukamet — galvanised lever clamp with safety lock The Horizontal clamp 112 is a galvanised horizontal lever clamp designed for fixed mounting on vertical bases and for secure 90° clamping in small‑scale production and workshop jigs. Galvanised steel construction for corrosion resistance Massive holding arm with integrated safety lock Vertical base fixing for secure installation 93 mm arm length, 90° clamping angle Dependable clamping force that secures workpieces reliably The clamp delivers a maximum holding force of 1,000 N and a maximum pressing force of 850 N, providing measurable resistance to slipping during machining or assembly. The distinction between holding force and pressing force is important: the first indicates the resistant force that keeps the workpiece in place, while the second describes the compressive load the clamp applies. These figures support rational planning of fixture layouts and allow engineers to compare clamping capacity with process forces, reducing reject rates and improving cycle reliability. The galvanised finish contributes to longevity in harsher shop environments. Robust mechanics minimise unplanned downtime A massive holding arm and an integrated safety locking mechanism reduce the risk of accidental release under vibration or impact, increasing operator safety and process stability. The clamp’s lever actuation operates with a direct mechanical linkage that is easy to inspect and service; simple maintenance routines preserve repeatability. The vertical base configuration ensures the clamp remains rigid after mounting, helping to keep set‑ups consistent across batches and limiting fixture adjustments during production changeovers. Compact design for flexible fixture integration With an arm length of 93 mm and a 90° clamping angle, the unit fits into confined jig spaces while maintaining effective reach. The low unit weight supports quick replacement and easy handling during fixture assembly without adding significant mass to tooling. The clamp’s compact geometry is suitable for repeatable positioning in fixtures where space is at a premium, enabling designers to pack multiple clamps around complex part geometries without compromising access for machining or inspection. Corrosion protection and workshop suitability The galvanised surface treatment provides a corrosion‑resistant layer that extends service life in environments subject to coolant mists or elevated humidity. Galvanisation also reduces the frequency of surface maintenance, supporting a straightforward upkeep regime and a predictable lifecycle cost for workshop managers. Combined with the clamp’s solid mechanical construction, the finish contributes to a tool that performs consistently under day‑to‑day production conditions. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet horizontal clamp 112 into your fixtures — telephone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: 112-1-D-L-C2 GTIN: 8680731502312 Model designation: 112 ECLASS: 21041719 ETIM: EC011973 Facts Arm length: 93 mm Maximum pressing force: 850 N Maximum holding force: 1,000 N Weight: 0.1 kg Clamping angle: 90° Special features Material: galvanised Fixing: vertical base Massive holding arm Safety locking mechanism Lever clamp FAQ What maximum holding force does the clamp provide? The clamp provides a maximum holding force of 1,000 N as stated for the Horizontal clamp 112 (SKU 112-1-D-L-C2). Is the clamp suitable for wet or humid workshop environments? Yes, the galvanised finish on the Kukamet clamp provides corrosion resistance suitable for humid shop conditions and reduces surface maintenance needs. How is the clamp mounted to a fixture? Mounting is performed via a vertical base fixing; the clamp is designed for secure installation on vertical fixture plates. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With Massive Holding Arm, 4.5 kN Thrust / 5 kN Holding Force, Zinc Plated - Kukamet
Compact durability for reliable clamping: the galvanised, heavy‑duty construction and 4,500 N clamping force combine to deliver consistent fixture stability and low maintenance. Order the clamp directly via Metav Werkzeuge or consult our specialists for application advice. 112 Horizontal clamp (lever clamp) by Kukamet — 4,500 N clamping force, 179 mm arm A robust horizontal lever clamp 112 designed for fixtures and jigs, featuring a vertical foot mounting and galvanised steel construction for lasting workshop performance Massive holding arm, 179 mm reach Vertical foot mounting for secure fit Galvanised steel construction, rust-resistant 4,500 N clamping force, 5,000 N hold force Consistent clamping power for production use The lever clamp delivers a 4,500 N rated clamping force and a maximum 5,000 N holding force, providing measurable stability for repetitive operations. Such numeric values indicate the clamp's capacity to resist displacement under load, which reduces rework and maintains machining tolerances. The clear specification of forces supports process planning and risk assessment in fixtures and assembly stations, enabling informed decisions about clamping points and safety margins. Built for durability and low upkeep Constructed from galvanised steel, the unit resists corrosion in workshop environments, which extends service life and reduces replacement frequency. The massive holding arm with a reach of 179 mm gives improved leverage and load distribution compared with slim-profile alternatives, lowering the risk of deformation under heavy use. The vertical foot mounting at a 90° angle ensures a compact footprint on fixture plates while providing robust attachment to stands or baseplates. Fast integration and dependable operation The horizontal lever mechanism offers straightforward actuation and repeatable clamping behaviour, simplifying jigs and fixture design and shortening setup times. The clamp’s moderate weight (1.485 kg) balances portability and stability, allowing relocation between stations without compromising rigidity. For workshop planners, this means predictable cycle performance and minimal adjustment during batch changes, supporting efficient production flow and fewer stoppages. For tailored guidance on integrating the Kukamet 112 horizontal clamp into fixtures or assemblies, contact Metav Werkzeuge for expert advice and secure supply from our Emmerich operations. Technical data Article number: 112-5-D-C2 GTIN: 8680731500660 ECLASS: 21041719 ETIM: EC011973 Facts Arm length: 179 mm Angle: 90° Clamping force: 4,500 N Holding force: 5,000 N Weight: 1.485 kg SKU: 112-5-D-C2 Special features Material: galvanised steel Mounting: vertical foot Massive holding arm Suitable for fixture and jig use Category: clamps FAQ What clamping and holding forces can be expected from this clamp? The Kukamet 112 horizontal clamp provides a clamping force of 4,500 N and a holding force up to 5,000 N, suitable for medium‑to‑heavy fixture applications. How is the clamp mounted to a workbench or fixture plate? Mounting is via a vertical foot arrangement; the vertical foot mounting ensures a compact, secure attachment to plates or stands for stable operation. Is the clamp suitable for use in humid or dusty workshop environments? The galvanised steel construction offers enhanced corrosion resistance, making the clamp appropriate for typical workshop conditions where moisture or airborne particles may occur. What reach does the holding arm provide and why does it matter? The holding arm extends 179 mm, offering increased leverage and better load distribution, which helps reduce the risk of deformation during repeat clamping cycles. Can this clamp be used for automated fixture systems? The lever action and defined clamping values make the clamp compatible with many fixture concepts; integration depends on the specific automation interfaces and mounting requirements. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With Massive Holding Arm, Safety Lock, 5 000 N Hold Force, Galvanised - Kukamet
Robust galvanised construction and a 129 mm arm combine with up to 5,000 N holding force to deliver dependable, repeatable clamping for jigs and fixtures; the built-in safety lock and vertical-foot mounting speed up setup and reduce downtime. Order the 112 horizontal clamp via Metav Werkzeuge or consult our advisors for application-specific recommendations. Kukamet 112 — Horizontal lever clamp, galvanised finish, 129 mm arm The Kukamet 112 is a horizontal lever clamp designed for secure fixturing in assembly and machining applications, offering a compact profile with a robust locking mechanism. Galvanised steel body for corrosion resistance Compact 129 mm arm for tight setups Safety lock prevents unintentional release Consistent, measurable clamping for reliable production The clamp delivers a clear performance advantage through its combination of 4,500 N clamping force and 5,000 N holding force, ensuring workpieces remain stable during processing. The specification values are directly relevant for fixture design: the holding force reflects the device’s resistance to shear and vibration, while the clamping force defines the pressure applied to the workpiece. For planners and shop managers this means fewer reworks and predictable process stability. Built for durability and operator safety A galvanised finish and a robust arm structure reduce maintenance cycles and protect against surface corrosion in workshop environments. The integrated safety lock provides a positive mechanical stop, preventing accidental opening under load and improving workplace safety. Mounted via a vertical foot, the clamp can be installed on plates or fixturing blocks and oriented at a 90° angle to suit horizontal clamping stations, combining compactness with secure operation. Fast installation and versatile application in fixtures The clamp’s 129 mm arm length and compact footprint make it suitable for use in confined jig spaces and automated assemblies. At only 1.42 kg, the device is easy to position during setup yet sufficiently heavy to remain stable once fixed. Its lever-style actuation allows quick engagement and release, shortening cycle times and supporting higher throughput. The design is particularly suitable for repetitive production, fixture retrofits and toolroom applications where reliable, repeatable clamping is required. Contact Metav Werkzeuge today for tailored guidance on integrating the Kukamet 112 into production fixtures and to confirm suitability for specific materials or machining processes. Technical Data Article number: 112-5-D-L-C1 GTIN: 8680731500684 Manufacturer: Kukamet Facts Weight: 1.42 kg Arm length: 129 mm Clamping force max: 4,500 N Holding force max: 5,000 N Angle: 90° eCl@ss: 21041719 ETIM: EC011973 Special features Material: galvanised steel Mounting: vertical foot Massive holding arm Safety lock Suitable for lever clamping applications FAQ What materials can the Kukamet 112 clamp reliably secure? The Kukamet 112 is designed for general-purpose clamping in jigs and fixtures; its galvanised steel body and robust arm make it suitable for a wide range of common workshop materials used in assembly and machining. How much space is required for installation of the clamp? Installation requires consideration of the 129 mm arm and the vertical-foot mounting; allocate clearance for lever travel and a 90° orientation when integrating the clamp into a fixture. Does the clamp include a locking mechanism to prevent accidental release? Yes, the Kukamet 112 is fitted with a safety lock that provides positive retention of the lever under load to reduce the risk of unintentional opening. Which SKU should be ordered for this horizontal clamp? Order the unit under SKU 112-5-D-L-C1; this refers to the Kukamet 112 horizontal lever clamp in the galvanised finish. Is the clamp suitable for demanding production environments? The galvanised surface and solid arm construction of the Kukamet 112 support durability in regular production use; the quick lever action also helps maintain cycle times in repetitive operations. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp With Vertical Base, Massive Holding Arm, 1,200 N Hold Force - Kukamet
Take advantage of a compact, high‑force clamping solution that combines a massive holding arm with a vertical foot for secure installation; the result is reliable, repeatable workholding that supports efficient production. Order the clamp directly via Metav Werkzeuge or consult our specialists for application advice. Horizontal clamp 112 — compact toggle clamp with massive holding arm and vertical foot (Kukamet) The Horizontal clamp 112 is a compact toggle clamp designed for secure workholding in jigs and fixtures, suitable for light‑duty assembly, welding and general workshop tasks Massive holding arm for rigid clamping Vertical foot for stable installation Max clamp force 1,000 N Lightweight 0.228 kg Increased process reliability through rigid construction The clamp’s massive holding arm provides consistently high clamping stiffness, reducing part movement during machining or assembly and improving repeatability. A robust lever design converts operator input into a controlled clamping action, so fixtures remain stable even under variable loads. The blackened finish offers basic surface protection and reduces visible wear, supporting longer intervals between replacement components and fewer unplanned stops. High clamping and holding forces for small fixtures With a clamp force of 1,000 N and a holding force of 1,200 N, the device supplies notable restraint for its size. The 116 mm arm length balances reach and mechanical advantage, allowing secure engagement with a variety of workpiece profiles while keeping the overall footprint small. These measurable values enable planners to calculate safety margins and select appropriate clamps for specific tasks, avoiding over‑engineering and ensuring efficient use of fixture space. Simple mounting and effortless integration into production Designed with a vertical foot and a 90° operating angle, the clamp is straightforward to attach to standard fixture plates or stops. At 0.228 kg, the component is light enough for rapid assembly into modular jigs yet rigid enough to withstand repetitive cycles. The unit’s toggle mechanism gives a clear locked position, making it suitable for assembly lines, inspection stations and welding jigs where fast manual operation and unmistakable engagement are required. For bespoke fixture concepts, the compact lever clamp adapts well to confined spaces and repetitive handling processes. Contact Metav Werkzeuge for procurement or technical advice on the Kukamet horizontal clamp 112 — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: B112-2-D-C2 GTIN: 8682843522189 Manufacturer: Kukamet Facts Arm length: 116 mm Clamp force: 1,000 N Holding force: 1,200 N Weight: 0.228 kg Operating angle: 90° Special features Vertical foot mounting Massive holding arm Blackened finish Compact toggle clamp Model: 112 FAQ What load capacities does this clamp support? The Kukamet horizontal clamp 112 provides a clamp force of 1,000 N and a holding force of 1,200 N, values suitable for many light‑duty fixtures and assembly tasks. Can the clamp be mounted on standard fixture plates? Yes, the vertical foot design of the clamp allows direct mounting to standard fixture plates and modular jig systems. Is the finish corrosion‑resistant? The unit has a blackened finish that offers basic surface protection against wear and light corrosion during normal workshop use. What is the reach of the clamping arm? The clamping arm measures 116 mm, offering a balance between reach and mechanical advantage for typical small‑part applications. Which applications are suitable for this clamp? The clamp is intended for light‑duty assembly, welding jigs, inspection fixtures and general workshop workholding where a compact, repeatable toggle clamp is required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 112 Horizontal Clamp, Heavy-Duty Arm, 2.3 kN Thrust, 2.5 kN Hold Force, Black Oxide Finish - Kukamet
Take advantage of a compact, heavy-duty clamp that combines a massive holding arm, reliable vertical-foot mounting and a verified 2,500 N max hold to secure repeatable production results; order the Horizontal clamp 112 directly via Metav Werkzeuge or consult the technical team for integration advice. Horizontal clamp 112 — Kukamet horizontal toggle clamp with 2.5 kN holding force A Horizontal clamp 112 designed for fixture and jig applications where a robust, compact toggle clamp with vertical-foot mounting and a blackened finish is required Massive holding arm construction Vertical-foot mounting for secure fixing Max holding force 2,500 N Blackened finish for wear resistance Secure clamping for consistent machining results The clamp delivers a clear, measurable benefit: 2,500 N maximum holding force paired with a clamping pressure of 2,300 N, providing stable fixation for repeated cycles. This level of force reduces part movement and vibration during machining, which leads to fewer rejects and less rework. The combination of a rigid arm and defined closing travel supports repeatable workholding, increasing throughput on small and medium-sized production runs without complex adjustments. Compact mounting that fits into jigs and fixtures With vertical-foot mounting and a right-angled orientation of 90°, the component integrates easily into tight fixture layouts. The short arm length and low mass (approx. 0.354 kg) make it suitable where minimised inertia and compact design matter. These attributes aid in straightforward jig retrofits and new fixture designs, shortening assembly time and maintaining a low profile on the workbench while still delivering industrial clamping performance. Durable construction for long service life Finished in a blackened coating, the clamp resists surface wear and provides corrosion protection for workshop environments. The massive holding arm and robust lever components are engineered for repeated manual actuation, so maintenance intervals remain long and unexpected downtime is minimised. The solid build quality supports continuous use in metalworking and assembly operations, where durability translates directly into lower lifecycle costs. Simple toggle mechanism for fast, repeatable operation The lever-style toggle design offers fast engagement and reliable locking without complex controls. The mechanism delivers consistent clamping travel and lock position, simplifying set-up and enabling predictable cycle times. For production contexts that need dependable manual clamps, this solution offers straightforward operation and low maintenance, so fixture repeatability and operator ergonomics are improved without added system complexity. Contact Metav Werkzeuge to discuss Kukamet clamp integration and to arrange prompt supply from Emmerich with application-specific advice and technical documentation Technical Data Article number: B112-3-D-C3 GTIN: 8680731507256 Manufacturer: Kukamet Numbers Arm length: 168 mm Max holding force: 2,500 N Max clamping pressure: 2,300 N Weight: 0.354 kg Angle: 90° Special features Mounting type: vertical foot Finish: blackened Massive holding arm Category: toggle clamp FAQ What is the maximum holding force of this clamp? The clamp provides a maximum holding force of 2,500 N; the clamping pressure is specified as 2,300 N for the Horizontal clamp 112 from Kukamet. How is the clamp mounted in a fixture? Mounting is by a vertical foot, intended for secure attachment to fixtures and jigs using standard fastening methods compatible with the clamp’s base. Is the finish suitable for workshop environments? Yes, the blackened finish offers surface wear resistance and basic corrosion protection ideal for general workshop and production use. Can this clamp be used for repeated production cycles? The toggle mechanism and massive holding arm are designed for repeatable manual actuation, supporting continuous use with low maintenance requirements. What is the arm length and overall weight? Arm length is 168 mm and the unit weight is approximately 0.354 kg, making it suitable for compact fixtures with limited mass allowance. Does the clamp lock at a specific angle? The clamp has a 90° orientation and provides a defined locked position typical for horizontal toggle clamps. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 113 Horizontal Clamp Heavy-Duty Arm With Safety Lock, Zinc-Plated - Kukamet
Combining a galvanised construction with a 217 mm lever arm and up to 5,000 N holding force, this horizontal clamp delivers secure, repeatable workpiece retention for fixture and jig applications. Benefit from a robust design with a safety locking mechanism and straightforward mounting on a 90° angle base; order the clamp directly via Metav Werkzeuge or consult our specialists for application advice. Horizontal clamp 113 (Kukamet) — galvanised, 5,000 N holding force The Horizontal clamp 113 is a lever clamp designed for stable, repeatable clamping in jigs, fixtures and production benches Galvanised steel construction Massive holding arm with safety lock 5,000 N holding force 90° angle base for stable mounting Secure, measurable clamping performance for production The 113 delivers clearly defined figures for industrial use: a holding force of 5,000 N and a maximum clamping/pressing force of 4,500 N, transmitted via a 217 mm lever arm. These values describe different aspects of performance — the clamping force reflects the active pressing action, while the holding force indicates the static retention capability once the clamp is engaged. On-shop-floor decision-making benefits from these objective numbers, as they enable direct comparison with other clamping elements and ensure that fixtures meet necessary retention and safety margins. The galvanised finish adds a predictable layer of protection in moderate workshop environments. Built for durability and safe repetition A massive holding arm combined with a positive safety lock reduces the risk of accidental release during repeated cycles. The structural design focuses on longevity under frequent use: components that take the load are dimensioned to limit deformation, and the locking feature secures the lever in the closed position for safe handling and transport of clamped assemblies. For production lines and jigs where consistency and operator safety are priorities, the combination of robust mechanics and a locking device supports uninterrupted operation and fewer rejects caused by shifting workpieces. Flexible mounting and compact integration The right‑angle or 90° angle base enables straightforward mounting to plates, fixture blocks and assembly tables while keeping the clamp profile compact. With a lever length of 217 mm, the device offers useful leverage without excessive reach, permitting close placement to neighbouring clamps or tooling. At 1.84 kg the unit is light enough for simple positioning yet heavy enough to remain stable once fixed. This balance supports integration into existing fixture designs and makes retrofitting on modular clamping plates uncomplicated. Low maintenance, high repeatability Designed for workshop reliability, the clamp requires only basic upkeep — periodic lubrication of the pivot points and occasional inspection of the locking mechanism. The galvanised body helps reduce surface corrosion and the solid lever geometry minimises play over the life cycle, ensuring repeatable clamping cycles and predictable positioning tolerance. For operations seeking to reduce rework and set-up time, the clamp contributes to a stable production flow by delivering consistent clamp engagement with minimal intervention. Discuss the Kukamet horizontal clamp 113 and mounting options with Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and specification support Technical data SKU: 113-5-D-L-C3 GTIN: 8680731501063 Category: Spanner EClass: 21041719 ETIM: EC011973 Core figures Arm length: 217 mm Holding force (max): 5,000 N Clamping/pressing force (max): 4,500 N Angle: 90° Weight: 1.84 kg Special features Galvanised steel body Angle base (right-angle) mounting Massive holding arm Safety locking mechanism Lever clamp type FAQ What is the difference between holding force and clamping force? The holding force refers to the static retention after the clamp is engaged (the 113: 5,000 N), while the clamping or pressing force is the active force applied during closure (4,500 N for this unit). Is the clamp corrosion-resistant? The horizontal clamp 113 has a galvanised finish that provides basic corrosion protection suitable for general workshop and production environments. How is the clamp mounted in a fixture? Mounting uses the 90° angle base to fasten the clamp to plates or fixture blocks; the right‑angle foot allows secure attachment and compact placement in jig assemblies. What routine maintenance does the clamp require? Maintenance is limited to periodic lubrication of pivots and visual checks of the safety locking mechanism and lever for wear to ensure long-term repeatability. Which applications are best suited to this lever clamp? The 113 is intended for jigs, fixtures and assembly benches where a reliable, repeatable horizontal clamping action is required and a clear specification for holding and clamping forces is needed. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 113 Horizontal Clamp With Massive 90mm Arm, 850 N Closing Force, Zinc Plated - Kukamet
Reliable clamping performance is delivered by the combination of a massive holding arm and 1,000 N holding force, while the galvanised 90 mm arm offers corrosion resistance for workshop environments; order the Horizontal toggle clamp 113 via Metav Werkzeuge or consult the technical team for application guidance. Horizontal toggle clamp 113 — 90 mm arm, galvanised, angle base Horizontal toggle clamp 113 is a compact horizontal hold-down clamp intended for secure fixturing in jigs and assembly fixtures, equipped with a 90° opening angle and an angle base for stable mounting. Massive holding arm for reduced deflection 1,000 N holding force for secure fixturing Galvanised finish for corrosion protection Angle base with 90° clamp position Secure clamping for repeatable setups The clamp offers a 1,000 N holding force combined with a pressing force of 850 N, providing consistent retention during repetitive operations. The robust toggle mechanism converts handle movement into reliable clamping action, reducing cycle times and the need for rework. Where repeatability and speed are priorities, the substantial holding performance of this clamp helps maintain process stability and improves throughput on assembly lines and fixture stations. Built for workshop conditions and long service life Constructed from galvanised steel and featuring a massive holding arm, the unit resists wear and environmental exposure while remaining compact and lightweight at approximately 0.156 kg. The solid arm reduces bending and improves load distribution, which translates into longer service intervals and lower maintenance demands. Corrosion-resistant coatings preserve function in humid or workshop environments, supporting dependable operation over time without frequent replacement. Simple integration into existing fixtures The clamp is supplied with an angle base for straightforward mounting at a 90° orientation, enabling fast incorporation into standard jigs and benches. The 90 mm arm length provides a balance between reach and leverage, making it suitable for a wide range of fixturing tasks. Its compact footprint and standardised mounting pattern facilitate retrofitting to existing tooling, while the mechanical toggle design ensures tool-free actuation for rapid clamping and unclamping during production cycles. For purchasing information or application advice on the Kukamet Horizontal toggle clamp 113, contact Metav Werkzeuge for ordering and technical consultation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 113-1-D-C2 GTIN: 8680731502930 Manufacturer: Kukamet SKU: 113-1-D-C2 Facts Weight: 0.156 kg Arm length: 90 mm Opening angle: 90° Holding force: 1,000 N Pressing force: 850 N eClass: 21041719 ETIM: EC011973 Special features Galvanised material Massive holding arm Angle base mounting Category: Clamp (Spanner) FAQ What materials is the clamp suitable for? The Horizontal toggle clamp 113 (Kukamet, SKU 113-1-D-C2) is designed for general-purpose fixturing and performs well on common workshop materials when used in appropriate setups. How is the clamp mounted to a fixture? Mounting is achieved via the supplied angle base; the Kukamet Horizontal toggle clamp 113 installs at a 90° position for secure attachment to jigs and benches. What are the key forces provided by the clamp? The device delivers a holding force of 1,000 N and a pressing force of 850 N, ensuring reliable retention during repetitive assembly tasks with the Kukamet Horizontal toggle clamp 113. Is the finish suitable for humid workshop environments? Yes, the galvanised finish on the Kukamet Horizontal toggle clamp 113 provides enhanced corrosion resistance suited to typical workshop conditions. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 113 Horizontal Clamp With Massive Holding Arm, 2.5 kN Hold Force, Galvanised - Kukamet
Combine a heavy-duty 108 mm arm, galvanised steel construction and a reliable 2,500 N holding force for consistent, repeatable fixturing; order the clamp directly via Metav Werkzeuge or consult our technical advisors for specification support. Horizontal clamp 113 — angle-foot mounting with galvanised heavy-duty arm (Kukamet) A Horizontal clamp 113 designed for robust 90° fixturing in jigs and production fixtures, supplied with an angle-foot mount for compact and repeatable installation. Heavy-duty holding arm Galvanised steel construction 90° angle-foot mounting Max holding force 2,500 N Secure, repeatable clamping for production workflows The Horizontal clamp 113 from Kukamet delivers dependable clamping where repeatability matters. Its heavy-duty holding arm and lever-style actuation ensure a firm mechanical hold with a max holding force of 2,500 N and a maximum clamping (pressing) force of 2,300 N, giving a clear distinction between sustained retention and instantaneous clamp pressure. This separation supports safer setup design and consistent cycle-to-cycle performance, reducing rework and downtime in batch production. Space-efficient mounting with corrosion-resistant construction Designed for compact fixturing, the clamp’s 90° angle-foot mounting and 108 mm arm length enable low-profile installation on fixtures and benches where space is limited. The body is galvanised, which provides a practical level of corrosion resistance suitable for general workshop and assembly environments; the light overall mass (approx. 0.414 kg) makes the unit easy to incorporate into portable jigs while still offering stable performance for repetitive operations. Durable design for long service life and simple integration Built with a massive holding arm and straightforward mounting, the clamp is aimed at production and maintenance settings that require long-lasting components. The compact horizontal layout and lever actuation allow integration into welding jigs, assembly stations and machining fixtures with minimal modification. The robust construction reduces maintenance intervals and, when combined with simple inspection routines, helps maintain clamping accuracy throughout the service life. For reliable clamping performance and tailored advice, request a technical consultation or quote from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for expert assistance. Technical data Article number: 113-3-D-C2 GTIN: 8680731500844 SKU: 113-3-D-C2 Brand: Kukamet Model: 113 Facts Arm length: 108 mm Angle: 90° Weight: 0.414 kg Max clamping force: 2,300 N Max holding force: 2,500 N eCl@ss: 21041719 ETIM: EC011973 Special features Material: galvanised steel Mounting: angle foot Massive holding arm Category: horizontal clamp / spanner Suitable for lever clamping applications FAQ What clamping and holding forces does the Horizontal clamp 113 provide? The Horizontal clamp 113 by Kukamet offers a maximum clamping (pressing) force of 2,300 N and a maximum holding force of 2,500 N, values that distinguish initial clamp pressure from sustained retention for reliable fixture performance. Is the Horizontal clamp 113 suitable for corrosive or humid workshop environments? The Horizontal clamp 113 has a galvanised steel finish that provides practical corrosion resistance for general workshop and assembly environments; for aggressive or specialised atmospheres, additional surface protection should be considered. How is the clamp mounted and what footprint is required? The Horizontal clamp 113 is fitted with an angle-foot mount for secure 90° installation; the arm length is 108 mm, allowing a compact footprint suitable for jigs, fixtures and bench mounting. Which applications are best suited to this horizontal lever clamp? Kukamet’s Horizontal clamp 113 is designed for jigs, welding fixtures, assembly stations and light production fixturing where a secure, repeatable hold and compact mounting are required. What are the key identifiers and dimensions for ordering and integration? The Horizontal clamp 113 (SKU 113-3-D-C2, GTIN 8680731500844) has an arm length of 108 mm, angle 90°, weight approx. 0.414 kg, and is supplied in galvanised steel for straightforward integration. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 113 Horizontal Clamp With Massive Holding Arm, 3.65 kN Holding Force - Kukamet
The combination of a massive holding arm and a compact, angled mounting makes this clamp a reliable choice for repetitive horizontal fixturing; its 3,500 N rated clamping force supports stable production processes. Order the clamp directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Horizontal clamp 113 — Kukamet lever clamp with 3,500 N clamping force and 191 mm arm The Horizontal clamp 113 is a robust lever clamp designed for secure horizontal fixturing in workshop and production environments, offering a compact footprint with an angled base for straightforward attachment. Massive holding arm for high rigidity 191 mm arm for extended reach 3,650 N maximum holding force Angle foot for secure horizontal mounting Stable, measurable clamping for reliable processes A focus on measurable performance ensures predictability on the shop floor: the fixture delivers 3,500 N rated clamping force with a maximum holding capability of 3,650 N, values that support repeatable workholding under load. The substantial holding arm reduces elastic deformation during clamping, which in practice means fewer reworks and faster cycle times. These objective figures enable planners to match the clamp to specific jigs or fixtures and to calculate safety margins for machining or assembly tasks. Built for rigidity and simple installation The lever clamp features a 191 mm arm that increases reach without substantially raising the overall bulk of the device. The angled mounting plate (Winkelfuß) allows secure horizontal attachment to tables or fixtures, simplifying integration into existing setups. A blackened finish provides basic surface protection and a discrete industrial appearance. The overall weight of 0.98 kg keeps the clamp manageable for retrofit work while the massive holding arm contributes to torsional stability during operation. Practical advantages that support daily workshop use Designed as a lever-operated horizontal clamp, the unit suits repetitive fixturing where quick engagement and secure retention are required. The compact dimensions and the angled base reduce interference with neighbouring clamps, supporting denser workholding layouts and therefore higher throughput. Robust metalwork and a focused feature set translate into lower maintenance requirements; the simple mechanical design supports long service intervals and straightforward spare-part logic. Discuss application specifics with Metav Werkzeuge for tailored fixturing solutions and the best variant for the intended workload — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: B113-4-D-C3 GTIN: 8680731507522 Model: 113 Core specifications Arm length: 191 mm Weight: 0.98 kg Clamping force (max): 3,500 N Holding force (max): 3,650 N Angle: 90° Special features Angle foot mounting Massive holding arm Finish: blackened Category: Spanner eClass: 21041719 ETIM: EC011973 FAQ What materials can be clamped with this lever clamp? The horizontal clamp 113 is a mechanical fixture intended for use with typical workshop workpieces; suitability depends on the clamping surface and fixture design rather than the clamp alone. How is the clamp mounted to a fixture plate? Mounting is achieved via the angled foot, which provides a stable horizontal mounting surface for bolting to tables or fixture plates. Does the clamp resist corrosion in a workshop environment? The device has a blackened finish that offers basic surface protection; further corrosion protection should be considered for aggressive environments. Is the lever arm replaceable if damaged? The clamp’s straightforward mechanical design allows for individual component servicing; check spare-part availability with the supplier or manufacturer. What distinguishes this clamp from lighter-duty fixtures? The combination of a massive holding arm, a 191 mm reach and a 3,500 N clamping rating delivers greater rigidity and holding capacity compared with lighter-duty clamps. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fast, secure workpiece clamping with toggle clamps
Toggle clamps, also known as knee lever clamps or lever clamps, are mechanical clamping elements used to fix components quickly and reliably in fixture construction, assembly, welding and testing. Their kinematic knee lever principle provides a one-motion closure that locks beyond a mechanical dead centre, delivering consistent clamping force with minimal operator effort.
How the locking principle benefits production
The kinematic dead-centre action means the clamp self-locks once closed, so no continuous force is required on the handle and the workpiece remains form-stable even under process-induced vibration. That behaviour translates directly into higher process reliability and faster cycle times: operators close the clamp in one swift move, parts stay in position during machining or inspection, and changeover times are reduced.
Practical advantages for everyday workshop use
- Reduced set-up time through single-motion clamping
- Consistent repeatability and process stability under vibration
- High holding force with low operator effort thanks to the dead-centre mechanism
- Durable construction for long service life in repetitive production
- Versatile mounting options for vertical, horizontal, push‑rod and draw applications
Technical overview
- principle: kinematic knee lever (dead-centre) locking
- application areas: fixture construction, assembly, welding, testing
- design variants: vertical clamp, horizontal clamp, push-rod clamp, draw/closure clamp
- material: high-strength zinc-plated steel; stainless steel options
- handle: ergonomic, oil-resistant handles
- joints: wear-resistant joint bushes
- process suitability: holds under strong, process-induced vibration; enables high repeatability
Metav as your precision partner
Metav combines decades of specialist knowledge with a broad, dependable assortment for industry and trade. With more than 48,000 customers, a catalogue exceeding 250,000 products and a quality filter based in Emmerich, Metav offers a practical, low-risk route to robust toggle clamps and accessories—ideal for buyers who need dependable stock, expert selection and consistent product quality.
In short: toggle clamps (knee lever clamps / lever clamps) deliver rapid, repeatable clamping with minimal operator effort, making them a straightforward productivity upgrade for demanding production environments.
FAQ
What exactly is a toggle clamp and how does it lock?
A toggle clamp uses a kinematic knee lever that passes a mechanical dead centre during closure; once over‑centre, the clamp self-locks, maintaining clamping force without continuous pressure on the handle.
Which toggle clamp type should I choose for sheet assembly or for pulling covers together?
Use vertical or horizontal toggle clamps for holding sheets and assemblies; choose draw/closure clamps when axial pulling or form closing is required. The variety of toggle clamp designs matches different fixture geometries and force directions.
Are toggle clamps suitable for high-vibration processes?
Yes. The dead‑centre locking of toggle clamps secures the workpiece even under strong, process-induced vibration, ensuring positional stability during machining or testing.
What materials and handle options are available for toggle clamps?
Common materials: zinc-plated steel and stainless steel. Handles are typically ergonomic and oil-resistant; joints use wear-resistant bushes for extended service life.
Can Metav help specify the right toggle clamp for my application?
Metav supplies a wide selection of toggle clamps and technical information, enabling selection based on application, material and required holding force; the assortment is supported by decades of precision experience and a large customer base.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com