Quick, secure clamping with lever clamps
Lever clamps provide rapid, repeatable workholding for fixture building, assembly, welding and testing, using the kinematic knee-lever principle to deliver self-locking retention and resist process vibrations. Designed for metalworking applications and made from high-strength materials such as zinc-plated steel or stainless steel, these clamps reduce setup and handling times while enabling high holding forces with minimal operator effort. Available in vertical and horizontal versions as well as thrust bar and closure styles, lever clamps ensure consistent positioning, long service life and enhanced process reliability for serial production. Key advantages include self-locking mechanism, high repeatability, reduced setup time and robust construction.
90° 167mm Horizontal Clamp With Massive Holding Arm, 4.5kN Thrust / 5kN Hold - Kukamet
Take advantage of the combination of robust clamping performance and compact mounting for reliable, repeatable setups. The clamp delivers up to 5,000 N holding force with a maximum clamping thrust of 4,500 N and a solid, massive holding arm for stable fixation in jigs and fixtures. Order the unit directly via Metav Werkzeuge or consult the team for specification support. Horizontal clamp 113 by Kukamet — 90° mounting, 5,000 N holding force Horizontal clamp 113 is a compact, right-angle clamp designed for secure workholding in production fixtures and assembly stations Massive holding arm for heavy-duty clamping 90° mounting with angled foot Holding force 5,000 N for secure fixation Blackened finish resists wear Consistent, measurable clamping performance that reduces rework The clamp provides a clear technical advantage where repeatability matters: a holding force of 5,000 N and a clamping thrust of 4,500 N ensure components remain immobile during machining, assembly or inspection. Specifying these figures in procurement and fixture design removes uncertainty about load capacity and enables reliable cycle times. The distinction between holding and clamping values is relevant for design: holding force describes the maximum retention under shear, while clamping thrust indicates the axial force the toggle mechanism can apply — both are decisive for preventing movement and subsequent quality faults. Robust construction and compact right-angle mounting for tight layouts A massive holding arm combined with a blackened finish delivers mechanical resilience and surface protection against abrasion in workshop environments. The angled foot mounting at 90° allows integration into vertical or horizontal fixture plates without adding excessive height, while the arm length 167 mm provides a balance between reach and rigidity. The compact mass (approx. weight 1.808 kg) simplifies handling during jig assembly and keeps load on sub-plates low, supporting modular fixture design and straightforward replacement when required. Designed for industrial fixtures and frequent operation Engineered for repetitive clamping cycles, the unit suits small-series production, assembly stations and bench fixtures where rapid, repeatable locking is required. The toggle-style action associated with this class of clamp delivers fast engagement and reliable mechanical advantage, reducing operator intervention and cycle time. The combination of decisive holding values and a sturdy arm instils confidence in process stability and contributes to lower scrap rates and less machine downtime. Procurement-friendly identifiers and integration details The clamp is catalogued for straightforward ordering and ERP integration with SKU B113-5-D-C2, GTIN 8680731507560, eClass 21041719 and ETIM EC011973, which supports accurate classification in purchasing systems. Key measurable data that assist specification and BOM entries include holding force 5,000 N, clamping thrust 4,500 N, arm length 167 mm, angle 90° and weight 1.808 kg. These entries facilitate compatibility checks, load calculations and fixture layout planning in design stages. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet Horizontal clamp 113 into fixtures and to confirm suitability for specific applications Technical Data SKU: B113-5-D-C2 GTIN: 8680731507560 Manufacturer: Kukamet Facts Weight: 1.808 kg Arm length: 167 mm Holding force: 5,000 N Clamping thrust (max): 4,500 N Angle: 90° eClass: 21041719 ETIM: EC011973 Special features Mounting: angle foot Finish: blackened Massive holding arm Designation: Horizontal clamp 113 FAQ What is the difference between holding force and clamping thrust? Holding force refers to the maximum retention under lateral load; clamping thrust is the axial force the mechanism applies. The Kukamet Horizontal clamp 113 specifies 5,000 N holding force and 4,500 N clamping thrust for clear engineering use. How is the clamp mounted in a fixture? The unit mounts via an angled foot at 90°, enabling secure attachment to jig plates and vertical or horizontal mounting faces for space-efficient fixture design. What materials and finish does the clamp have? The clamp features a blackened finish that resists abrasion. The robust arm construction is intended for workshop environments with frequent operation. Is the clamp suitable for automated or high-cycle stations? Yes, the toggle-style mechanism and massive holding arm provide reliable, fast engagement suited to repetitive cycles; reference SKU B113-5-D-C2 when specifying for automation. How can the clamp be referenced in procurement systems? Use the identifiers GTIN 8680731507560, eClass 21041719 and ETIM EC011973 to ensure correct classification and compatibility in purchasing systems. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 168mm Horizontal Clamp With Massive Holding Arm, Max Clamping Force 2,500 N - Kukamet
The combination of a massive holding arm, galvanised finish and a compact 168 mm reach ensures dependable clamping in assembly and fixture work; the device delivers up to 2,500 N holding force and 2,300 N clamping force for secure, repeatable results. Order the Horizontal clamp 111 directly via Metav Werkzeuge or ask our consultants if needed. Horizontal clamp 111 — Kukamet horizontal toggle clamp with galvanised finish and 168 mm arm The 111 Horizontal clamp secures components in jigs and fixtures with a robust holding arm and high holding capacity, designed for bench-mounted horizontal applications. Massive holding arm for secure clamping Galvanised finish for corrosion resistance Holding force up to 2,500 N Horizontal foot for bench mounting Dependable clamping where repeatability matters The robust construction of this horizontal toggle clamp provides consistent securing of workpieces, making it suitable for repetitive assembly and fixture tasks. The massive holding arm minimises deflection under load, which preserves part position and reduces rework. With a compact 168 mm arm, the clamp reaches into tight jigs while maintaining clearance for tool access, so throughput improves without sacrificing precision. Built to withstand workshop conditions A galvanised finish protects the clamp against corrosion in workshop environments, extending service life and reducing maintenance intervals. The unit’s light overall mass and durable components combine to offer a long-lasting clamping solution that resists wear from daily use. The combination of 2,500 N holding force and 2,300 N clamping force ensures reliable performance across a range of non-machining fixtures and manual assembly stations. Simple integration into fixture systems Designed with a horizontal foot for secure bench mounting, the clamp fits into existing jigs and modular tooling with minimal adaptation. The 90° locking angle provides a low-profile locked position, enabling stacked or adjacent clamping arrangements without interference. Where repeatable positioning and fast actuation are required, this clamp offers a compact, mechanically straightforward option that reduces cycle times. For fixture upgrades or bulk enquiries, request the Kukamet Horizontal clamp 111 from Metav Werkzeuge — Metav Werkzeuge can advise on compatibility and supply from Emmerich; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: 111-3-D-C3 GTIN: 8680731500165 eClass: 21041719 ETIM: EC011973 Facts Arm length: 168 mm Holding force: 2,500 N Clamping force: 2,300 N Weight: 0.362 kg Locking angle: 90° Special features Material: galvanised Mounting: horizontal foot Massive holding arm Category: Toggle clamp / horizontal clamp Brand: Kukamet FAQ What materials can this clamp be used with? The Kukamet Horizontal clamp 111 is suitable for general fixture work and is typically used to secure components made of metals and plastics in assembly and jigs; material compatibility depends on the fixture design and clamping strategy. How much force does the clamp hold reliably? Rated holding force for the Horizontal clamp 111 is up to 2,500 N, with a clamping force of 2,300 N, providing a stable and repeatable clamp for production fixtures. How is the clamp mounted to a workbench or jig? The clamp features a horizontal foot mounting arrangement, allowing secure bolting to benches, fixture plates or modular tooling systems for fixed-position clamping. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 168mm Horizontal Clamp With Solid Arm, Safety Lock, 2.3kN Press Force - Kukamet
Take advantage of a robust, low-maintenance clamping solution that combines solid holding arm construction, corrosion-resistant galvanised steel, and dependable holding force for stable jigs and fixtures. Order the clamp directly via Metav Werkzeuge or consult the Metav team for application advice. Horizontal toggle clamp 112 — Kukamet horizontal clamp with 2,500 N holding force, galvanised finish A Horizontal toggle clamp 112 designed for secure, repeatable workpiece retention in jigs and fixtures, featuring a vertical base and a 90° clamping angle for consistent positioning Solid holding arm with safety lock Up to 2,500 N holding force Galvanised steel construction Vertical base for secure mounting 90° clamping angle, 168 mm arm Consistent, measurable clamping performance for production use The clamp delivers clear technical figures: a maximum clamping force of 2,300 N and a maximum holding force of 2,500 N, values that support repeatable setup and reduced rework in series production. Stating these numeric characteristics makes selection straightforward for engineers who compare tools by mechanical performance. The distinct separation between clamping and holding values explains why the device holds components securely under load while allowing positive actuation during setting and release, improving cycle reliability on assembly or welding jigs. Corrosion resistance and compact integration reduce downtime Constructed from galvanised steel and weighing just 0.3 kg, the clamp combines durability with easy handling. The vertical base mounting allows direct attachment to fixture plates or workbenches, eliminating complex subframes. The 168 mm arm provides a practical lever reach for reliable engagement without excessive footprint. These design choices translate into less maintenance, longer service life in damp or workshop environments, and simplified retrofitting into existing tooling layouts. Secure operation and safe workshop handling A solid holding arm with an integrated safety lock prevents accidental release during machining or handling, while the fixed 90° clamping angle ensures consistent orientation of the workpiece every cycle. The mechanical design prioritises straightforward inspection and low upkeep: components are accessible for routine checks and replacement if required. This makes the clamp suitable for repetitive tasks where operator safety, process stability and quick visual inspection are priorities. Contact Metav Werkzeuge for application guidance and to request the Kukamet Horizontal toggle clamp 112 (SKU 112-3-D-L-C3) for robust, reliable holding in production fixtures — info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: 112-3-D-L-C3 GTIN: 8680731500547 Manufacturer: Kukamet Core specifications Arm length: 168 mm Clamping force (max): 2,300 N Holding force (max): 2,500 N Clamping angle: 90° Weight: 0.3 kg Materials & special features Material: galvanised steel Mounting: vertical base Special features: solid holding arm, safety lock eClass: 21041719 ETIM: EC011973 FAQ What holding and clamping forces can be expected from this clamp? The Kukamet horizontal toggle clamp 112 offers a maximum clamping force of 2,300 N and a maximum holding force of 2,500 N, providing measurable performance for fixture design and strength calculations. Is the clamp suitable for use in corrosive workshop environments? Yes, the galvanised steel finish gives the clamp enhanced corrosion resistance, making the unit appropriate for typical workshop exposure and long-term use. How is the clamp mounted and what space does it require? Mounting is via a vertical base, allowing direct attachment to fixture plates; the 168 mm arm provides practical reach while keeping the overall footprint compact. Does the clamp include safety features to prevent accidental release? The design includes a safety lock and a rigid holding arm that secures the workpiece at a fixed 90° angle, reducing the risk of unintended opening during operations. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 168mm Horizontal Clamp With Solid Holding Arm, 2.5kN Hold Force, Black Brown Oxide - Kukamet
Take advantage of a robust lever clamping solution that combines a massive holding arm, a compact 168 mm reach and a reliable 2,500 N holding force for steady fixture operation; order directly via Metav Werkzeuge or consult the specialists for integration advice. Kukamet Horizontal clamp 111 – horizontal lever clamp with 2,500 N holding force and 168 mm arm The Horizontal clamp 111 is a lever-operated horizontal clamp designed for secure, repeatable workpiece holding in assembly, welding and fixture applications. Massive holding arm, 168 mm reach Horizontal base for fixture mounting Holding force up to 2,500 N Durable blackened finish Dependable clamping performance that reduces rework The clamp combines a high holding force with precise mechanical leverage to secure components reliably during repetitive operations. Its rated holding force of 2,500 N and nominal clamping force of 2,300 N provide a measurable performance basis for process planning, enabling higher throughput and fewer stoppages due to loose workpieces. Where consistent positioning matters, repeatable clamping mitigates the need for remedial adjustments and supports stable cycle times on production lines. Robust build and compact integration for jigs and fixtures A massive holding arm with a 168 mm reach gives the clamp both strength and useful span for many fixture layouts, while the horizontal base is tailored for straightforward mounting to plates and welding jigs at a right angle. The 90° orientation simplifies alignment in common fixture frames and reduces the need for adapter parts. The blackened finish offers a hardwearing surface that lowers the visible wear rate in industrial environments and supports long-term alignment accuracy. Simple operation and pragmatic maintenance for busy workshops Designed as a lever-operated toggle clamp, operation is immediate and intuitive, shortening set-up time at the workbench. With a low mass of 0.362 kg, the clamp is easy to handle during assembly yet engineered for stable holding under load. Routine care is limited to periodic inspection of the pivot and hinge points and light lubrication of moving parts to maintain smooth motion and consistent clamping force. The compact design therefore delivers operational reliability with minimal downtime. For robust fixture clamping where repeatability matters—rely on Kukamet quality and arrange procurement or technical advice through Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: B111-3-D-C3 GTIN: 8680731507010 eClass: 21041719 ETIM: EC011973 Core technical data Arm length: 168 mm Maximum holding force: 2,500 N Maximum clamping force: 2,300 N Angle: 90° Weight: 0.362 kg Special features Horizontal base (waagerechter Fuß) Massive holding arm Lever-operated clamp (hebelspanner) Blackened finish (Schwarz brüniert) SKU: B111-3-D-C3 FAQ What is the maximum holding force of this clamp? The maximum holding force is 2,500 N for the Kukamet Horizontal clamp 111, giving a clear performance metric for fixture design. How is the clamp mounted to a fixture? Mounting is via a horizontal base suitable for bolting to plates or jigs; the horizontal orientation aligns the clamp at 90° for many standard fixtures. What reach does the holding arm provide? The holding arm provides a 168 mm reach, offering a balance between compact size and practical span for a range of workpieces. Is this clamp suitable for assembly and welding fixtures? Yes, the lever-operated design and robust arm make it suitable for assembly and welding fixtures that require secure, repeatable clamping. What maintenance does the clamp require? Maintenance is limited to regular inspection of pivots and light lubrication of moving joints to preserve consistent clamping action and service life. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 179mm Horizontal Clamp With Massive Arm And Safety Lock, 5 000 N Hold Force - Kukamet
Benefit from a compact, heavy-duty clamping solution that combines a 179 mm solid arm with a 5,000 N holding force and a secure safety lock for consistent, repeatable workholding. Order the clamp directly via Metav Werkzeuge or consult our specialists to confirm suitability for fixtures and production jigs. Horizontal toggle clamp 112 — horizontal clamp with 179 mm arm and 5,000 N holding force (Kukamet) Horizontal toggle clamp 112 is a horizontal clamping device designed for fixture, jig and workshop use, delivering repeatable positioning and robust retention for medium-duty production environments. 179 mm heavy-duty arm 5,000 N maximum holding force 4,500 N clamping force Safety locking mechanism Secure clamping where accuracy matters The clamp delivers a high holding force while keeping the kinematic footprint small, making it suitable for jigs and fixtures where repeatability matters. The combination of a 179 mm arm and a 5,000 N holding force produces secure retention with low elastic deformation, which reduces rework and inspection effort. The toggle mechanism converts manual lever action into stable clamping pressure; this mechanical advantage is reliable in series production and short-run assembly alike. Precision in positioning is aided by the rigid arm and defined stop angle, so parts are held consistently for machining, drilling or assembly operations. Designed for standardised mounting and integration A vertical foot mounting style allows straightforward attachment to fixture plates, frames and tooling bases at a right angle, enabling compact layout and predictable clamp orientation. The built-in 90° angle and the clamp’s modest weight of 1.42 kg help to keep masses low on moving fixtures and reduce load on positioning systems. The design supports quick retrofitting into existing jigs and the solid construction minimises maintenance intervals. In workshops where cycle times and changeover speed matter, this toggle clamp offers a pragmatic balance of sturdiness and compactness. Durable finish and built-in safety for everyday use The component features a black case-hardened finish that improves surface wear resistance and provides corrosion protection in typical workshop environments. A massive holding arm and an integrated safety locking mechanism prevent unintended release under vibration or shock, increasing operator confidence and process safety. The clamp’s mechanical simplicity means servicing is straightforward and spare parts are minimal, contributing to predictable lifecycle costs. For operations that prioritise both safety and uptime, this clamp provides a practical, long-lived workholding solution. Discuss application requirements with Metav Werkzeuge to ensure the Kukamet Horizontal toggle clamp 112 matches the fixture specifications and production demands — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice Technical data Article number: B112-5-D-L-C2 Name: Horizontal toggle clamp 112 Brand: Kukamet Mounting: vertical foot Core technical data Arm length: 179 mm Holding force: 5,000 N Clamping force (max): 4,500 N Weight: 1.42 kg Angle: 90° Special features Massive holding arm and safety locking Black case-hardened finish Vertical foot mounting Lever clamp mechanism FAQ What is the maximum holding force of this clamp? The Kukamet horizontal toggle clamp 112 provides a maximum holding force of 5,000 N, suitable for medium-duty fixture applications. What clamping force can be expected during operation? Operational clamping force is specified at 4,500 N, which is the effective clamping pressure achievable with the toggle mechanism on the Horizontal toggle clamp 112. How is the clamp mounted to a fixture plate? Mounting is via a vertical foot, allowing attachment at a right angle to plates or frames for compact layout and consistent clamp orientation. Is the finish suitable for workshop environments? The clamp has a black case-hardened finish that increases wear resistance and provides basic corrosion protection for typical workshop conditions. Does the clamp include a safety lock? Yes, the design incorporates a safety locking mechanism and a massive holding arm to reduce the risk of accidental release during vibration or handling. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 179mm Horizontal Clamp With Massive Holding Arm, 5 000 N Hold Force - Kukamet
Combine a 179 mm massive holding arm with up to 5,000 N holding force and a compact 1.485 kg body for stable, repeatable clamping in jigs and fixtures; order via Metav Werkzeuge or consult the specialists for application advice. Horizontal clamp 112 — heavy-duty lever clamp with 179 mm arm (Kukamet) The Horizontal clamp 112 is a lever-operated horizontal clamp designed for secure workpiece holding in jig, fixture and assembly applications where repeatable clamping force and fast operation are required Massive 179 mm holding arm Up to 5,000 N holding force Vertical-foot mounting for stability Blackened, corrosion-resistant finish Consistent clamping performance that improves throughput The robust toggle mechanism delivers a clearly defined clamping force of 4,500 N and a holding force up to 5,000 N, ensuring consistent part retention during machining, welding or assembly. The 179 mm arm gives an extended lever reach for better access and secure engagement at a 90° orientation, reducing rework and inspection needs. This measurable performance translates directly into predictable cycle times and fewer process interruptions, supporting continuous production environments. Rugged construction for long service life and simple mounting Constructed with a massive holding arm and a blackened finish, the clamp combines mechanical strength with surface protection against wear. The vertical-foot mounting provides a compact and stable interface to fixture plates or machine bases, while the unit’s 1.485 kg weight balances inertia and manoeuvrability. The surface treatment reduces corrosion risk and eases maintenance requirements, so downtime for upkeep is minimised and component replacement cycles are extended. Practical advantages for jig builders and workshop use As a lever clamp, the device enables fast manual operation and secure locking with a tactile, repeatable action that speeds set-up and assembly tasks. The compact footprint and robust arm make it suitable for dedicated fixtures, modular tooling systems and small-batch production. Clear numerical ratings and a straightforward mechanical design simplify integration into existing tooling arrangements and support predictable quality outcomes in demanding shop-floor conditions. Contact Metav Werkzeuge for application support or to secure the Kukamet Horizontal clamp 112 for prompt supply from Emmerich Technical data Article number: B112-5-D-C2 GTIN: 8680731507348 Manufacturer: Kukamet Facts Arm length: 179 mm Holding force (max): 5,000 N Clamping force (max): 4,500 N Angle: 90° Weight: 1.485 kg Special features Massive holding arm Vertical-foot mounting Blackened, corrosion-resistant finish Lever-operated horizontal clamp FAQ What maximum holding force does the clamp provide? The Kukamet Horizontal clamp 112 offers a holding force of up to 5,000 N; clamping force is specified at 4,500 N for secure workpiece retention. How is the clamp mounted? Mounting is via a vertical foot that provides a stable connection to fixture plates or machine beds for fixed jig and fixture installations. What are the key dimensions relevant to fixture design? Relevant dimensions include a 179 mm arm length and a locking angle of 90°, with a unit weight of 1.485 kg for handling and layout considerations. Is the surface suitable for workshop environments? The clamp features a blackened, corrosion-resistant finish that improves wear resistance and reduces maintenance requirements in industrial settings. Which SKU should be referenced when ordering spare parts or replacements? Reference SKU B112-5-D-C2 for this Kukamet horizontal clamp to ensure correct identification and supply. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 179mm Horizontal Clamp With Solid Holding Arm, 5,000 N Holding Force - Kukamet
Combine a 179 mm arm, 5,000 N holding force and a compact 1.48 kg construction for dependable, repeatable clamping in production environments; order the horizontal clamp directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Horizontal clamp 111 »B111-5-D-C2« – 5,000 N holding force, 179 mm arm (Kukamet) A Horizontal clamp 111 engineered for secure workholding in assembly and machining, featuring a horizontal foot mount and a massive holding arm for consistent clamping at right angles Massive holding arm Horizontal foot for secure mounting Holding force 5,000 N Clamping force 4,500 N Robust clamping for industrial workholding The clamp delivers industrial-grade performance through its 5,000 N holding force and 4,500 N clamping force, which together ensure reliable fixation of components during machining and assembly. The 179 mm arm provides a practical reach for many fixturing tasks while the compact mass keeps the device easy to integrate into existing jigs. By specifying measurable values for holding and clamping, the design supports consistent repeatability and reduces fixture adjustments, helping to maintain cycle-time targets on repetitive operations. Engineered durability to reduce downtime Durability is achieved by a massive holding arm and a hard-wearing blackened finish that resists wear in workshop conditions. The lever mechanism is designed for frequent operation and a long service life, reducing the likelihood of unexpected maintenance. The relatively low mass of 1.48 kg balances robustness with ease of handling, so replacement or repositioning on the production floor is straightforward. These features combine to lower total cost of ownership through fewer interruptions and longer intervals between part replacements. Straightforward installation and technical clarity The clamp is mounted via a horizontal foot, enabling stable, right-angled fixation without complex adapters. Measurable technical data—arm length, holding and clamping forces, weight and mounting type—simplify integration into existing fixtures and allow quick verification against engineering requirements. For users less familiar with clamping terminology: holding force refers to the static retention capacity, while clamping force describes the applied load during engagement. Clear specifications support confident selection and minimise installation uncertainty. Contact Metav Werkzeuge for tailored configuration and delivery from Emmerich; technical advice and specification checks are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: B111-5-D-C2 GTIN: 8680731507089 Model: 111 Facts Arm length: 179 mm Holding force: 5,000 N Clamping force: 4,500 N Weight: 1.48 kg Angle: 90° Special features Mounting: horizontal foot Material/finish: blackened finish Massive holding arm Category: Spanner eClass: 21041719 ETIM: EC011973 FAQ What materials can this clamp be used with? The Kukamet Horizontal clamp 111 (SKU B111-5-D-C2) is suitable for general workshop clamping and can be used with a wide range of workpiece materials when paired with appropriate fixturing; materialspecific limits depend on the overall fixture design. How is the clamp mounted to a fixture or machine table? Mounting is via the horizontal foot provided; the horizontal foot enables rigid, right-angled attachment to fixtures and plates for secure positioning. Does the lever require frequent maintenance? The lever mechanism is designed for high-frequency use and the robust construction of the Kukamet clamp 111 minimises routine maintenance; inspection intervals should follow in-house maintenance schedules. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 180mm Pneumatic Clamp With Vertical Base, Heavy-Duty Arm, 4.5kN Push / 5kN Hold, Galvanised - Kukamet
Take advantage of the combination of robust holding capacity, a substantial 180 mm arm and a corrosion-resistant finish for reliable, repeatable clamping in production fixtures; order the component or consult Metav Werkzeuge for specification support. Pneumatic Clamp 651 – Vertical-foot pneumatic lever clamp with 180 mm arm and galvanised finish Pneumatic Clamp 651 is a compact pneumatic lever clamp designed to secure workpieces at a fixed 90° angle in assembly, welding and fixture applications. 180 mm heavy-duty holding arm Vertical-foot mounting for stability Galvanised finish for corrosion protection 5,000 N maximum holding capacity Consistent, powerful clamping for repeatable production results The pneumatic actuation delivers fast, repeatable clamping cycles that reduce setup variation and rework. With a holding capacity of 5,000 N and a maximum actuation force of 4,500 N, the device provides measurable performance for medium-duty fixtures; the fixed 90° orientation ensures consistent part positioning in assemblies. Those figures describe objective capability and support decisions for jigs where repeatability and throughput are critical, enabling predictable cycle times and improved production quality. Robust construction that endures workshop use A galvanised finish and a massive holding arm make the unit resilient against mechanical wear and environmental exposure typical in industrial workspaces. The vertical-foot mounting provides a low centre of gravity and increases stability under lateral loads, so fixtures remain secured during machining or welding operations. The design focuses on long service life and low maintenance, translating technical durability into fewer interruptions on the shop floor and a dependable component for daily use. Easy integration into fixtures and flexible layout options The 180 mm arm length gives reach for a variety of clamping geometries while keeping a compact footprint for tight fixtures. As a lever clamp, the unit integrates directly into modular plates and bespoke jigs, enabling straightforward replacement of manual clamps with pneumatic operation for faster cycle rates. Pneumatic actuation also simplifies control integration with existing compressed-air systems, allowing automated or semi-automated clamp sequences without complex retrofitting. For specialised fixture requirements, technical documentation is available to verify dimensional fit and mounting clearances. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating the Kukamet Pneumatic Clamp 651 into production fixtures; technical consultants can confirm compatibility, delivery options and specification details via info@metav-werkzeuge.com or +49 2822 7131930. Technical data Name: Pneumatic clamp 651 SKU: 651-5-D-C2 Manufacturer: Kukamet Core specifications Arm length: 180 mm Holding force (max): 5,000 N Actuation force (max): 4,500 N Angle: 90° eClass: 21021004 ETIM: EC011973 Design & features Vertical-foot mounting Massive holding arm Galvanised material Lever clamp style (pneumatic) Category: Clamping devices FAQ What clamping force can be expected from this clamp? The Pneumatic Clamp 651 provides a holding capacity of up to 5,000 N and a maximum actuation force of 4,500 N, which suits medium-duty fixture tasks. Can the clamp be mounted directly on assembly plates? Yes, the vertical-foot configuration of the Pneumatic Clamp 651 is intended for fixed mounting on plates and ensures a stable base for fixture assemblies. Is the clamp suitable for welding environments? The galvanised finish on the Pneumatic Clamp 651 improves corrosion resistance and durability, making it a practical choice for shop-floor environments, including light welding stations. What reach does the clamping arm offer for bespoke jigs? The device features an arm length of 180 mm, offering extended reach for a variety of clamping geometries while maintaining a compact installation profile. Where can detailed dimensional data and installation information be obtained? Technical documentation for the Pneumatic Clamp 651, including mounting dimensions and integration notes, is available on request; Metav Werkzeuge can provide the specific files and guidance. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 180mm Pneumatic Clamp With Vertical Handle And Massive Arm, 4.5kN Push / 5kN Hold, Galvanised - Kukamet
Robust pneumatic clamping with 4,500 N actuation and up to 5,000 N holding force ensures stable, repeatable fixture performance. The vertical-foot mounting and zinc-plated heavy-duty arm provide corrosion resistance and long service life in busy production environments. Order directly via Metav Werkzeuge or consult the technical team for specification support. 651 Pneumatic toggle clamp — vertical handle, 4,500 N actuation (Kukamet) The 651 is a vertical-foot pneumatic toggle clamp engineered for secure workpiece retention in production fixtures, jigs and assembly lines, where space-efficient, repeatable clamping is required Vertical handle with heavy-duty arm 4,500 N pneumatic actuation force 5,000 N maximum holding force Zinc-plated finish for corrosion resistance Consistent clamping performance for continuous production The pneumatic drive provides consistent clamping force, ensuring reliable cycle-to-cycle performance and reduced rework. With an actuation force of 4,500 N and a maximum holding force of 5,000 N, the device maintains stable contact under varying loads, which improves process quality and repeatability. Pneumatic control removes manual variability, supporting automated or semi-automated lines and allowing predictable fixture behaviour that shortens set-up times and minimises downtime. Compact, robust design that withstands shopfloor demands A massive holding arm and a 180 mm reach deliver secure support for medium-weight components while keeping the overall footprint compact. The clamp is finished zinc-plated to resist corrosion and wear in industrial environments, and the vertical handle with a 90° orientation offers ergonomic actuation and reduced interference with neighbouring tooling. The vertical-foot mounting permits dense fixture layouts without compromising accessibility, combining durability with space efficiency. Straightforward integration and low-maintenance operation Designed for quick installation on a vertical foot, the clamp allows easy incorporation into existing jigs and modular fixture systems. Pneumatic supply requirements are standard, and the toggle mechanism is optimised for longevity, reducing maintenance intervals and service costs. Simple inspection and routine checks of seals and connections keep the clamp operational with minimal effort, supporting continuous production schedules and high equipment availability. For reliable heavy-duty clamping in fixtures, select the Kukamet 651 and contact Metav Werkzeuge for tailored advice and ordering: info@metav-werkzeuge.com • +49 2822 7131930 Technical Data Article number: 651-5-H-D-C2 Product: Pneumatic toggle clamp, 651 Brand: Kukamet Facts Actuation force: 4,500 N Maximum holding force: 5,000 N Arm length: 180 mm Angle: 90° eCl@ss: 21021004 ETIM: EC011973 Special features Vertical handle Massive holding arm Vertical foot mounting Material: zinc-plated Lever-clamp design FAQ What clamping and holding forces does this clamp provide? The Kukamet 651 offers an actuation force of 4,500 N with a maximum holding force of 5,000 N, providing secure retention for medium-weight workpieces. How is the clamp mounted in a fixture? Mounting is via the vertical foot, designed for straightforward integration into jigs and fixture plates; the 180 mm arm ensures adequate reach and clearance. Is the clamp suitable for automated production lines? Yes, the pneumatic actuation and repeatable toggle mechanism make the 651 appropriate for automated and semi-automated production environments. What material protection does the clamp have against corrosion? The clamp features a zinc-plated finish that provides corrosion resistance suitable for general workshop and light industrial conditions. What routine maintenance is required? Routine checks of pneumatic connections, seals and the toggle mechanism are recommended; the 651’s robust design minimises maintenance frequency. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 191mm Horizontal Clamp With Massive Holding Arm And Safety Lock, 3.65kN Holding Force - Kukamet
Secure, repeatable clamping is provided by the compact Horizontal clamp 113, featuring a 191 mm arm and up to 3.5 kN clamping force; its massive holding arm and integrated safety lock support safe operation in production and workshop environments. Order the clamp directly via Metav Werkzeuge or consult our specialists for technical matching and application advice. Horizontal clamp 113 — Kukamet horizontal lever clamp with 191 mm arm and safety lock A robust Horizontal clamp 113 intended for 90° workholding, combining a compact footprint with a massive holding arm and an integrated safety locking mechanism. Massive holding arm construction Integrated safety locking mechanism 191 mm arm for deep reach Up to 3,650 N holding force Reliable clamping for repetitive production The compact lever clamp is engineered to deliver consistent clamp force across repeated cycles, making it suitable for jigs, fixtures and serial production set-ups. The specified 3.5 kN clamping force and a rated 3.65 kN holding force provide a measurable basis for process planning and ensure that fixture designs remain stable under cutting and assembly loads. Using quantifiable force values enables predictable process control and reduces rework, while the lever-style actuation allows rapid engagement and disengagement for efficient takt times. Durable construction that endures workshop conditions Built with a massive holding arm and a protective black oxide finish, the clamp resists routine wear and offers basic corrosion protection without bulk. The solid construction contributes to low vibration sensitivity and long service life, yet the device remains compact at approximately 0.94 kg, simplifying integration into existing fixtures. The safety lock prevents accidental release during handling, improving operator safety and reducing the risk of workpiece movement during secondary operations. Simple mounting and precise positioning Designed for secure attachment with an angle foot mounting, the clamp locates reliably at 90° for common right-angle workholding arrangements. The 191 mm arm extends reach into deeper jigs while maintaining leverage for strong engagement, and the lever principle allows quick manual toggling where pneumatic or hydraulic systems are not required. Its compact dimensions and clear mechanical specifications support straightforward fixture design and shorter lead times for assembly — a practical benefit for small-batch manufacturing and maintenance tasks. Choose Kukamet’s Horizontal clamp 113 for dependable, compact workholding—contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for ordering and application guidance. Technical data SKU: B113-4-D-L-C3 Model: 113 Brand: Kukamet ECLASS: 21041719 ETIM: EC011973 Core specifications Arm length: 191 mm Mounting: angle foot Clamping force max: 3,500 N Holding force max: 3,650 N Angle: 90° Weight: 0.94 kg Special features Material: black oxide finish Massive holding arm Safety locking mechanism Suitable for lever clamping applications FAQ What is the difference between clamping force and holding force for this clamp? Clamping force refers to the applied force when the lever is actuated; the Horizontal clamp 113 is rated at 3.5 kN clamping force, while the holding force of 3.65 kN indicates the maximum sustained retention capacity under load. Can the clamp be mounted in compact fixtures or only on flat plates? The clamp uses an angle foot mounting, enabling installation in compact fixtures and typical right-angle setups; the footprint suits confined fixture layouts without compromising reach thanks to the 191 mm arm. Is the clamp finish suitable for industrial environments? The black oxide finish provides basic corrosion resistance and wear protection appropriate for workshop environments; the robust mechanical design also helps the unit withstand routine industrial use. How does the safety locking mechanism benefit workshop operations? The integrated safety lock prevents unintended release of the lever during handling and machining, improving process safety and reducing the chance of workpiece displacement during secondary operations with the Kukamet clamp (SKU B113-4-D-L-C3). Is the clamp suitable for manual toggling or does it require automation? The lever-style design is intended for manual actuation and rapid engagement; it is suitable where pneumatic or hydraulic systems are not required, delivering quick cycle times for hand-operated fixtures. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 191mm Horizontal Clamp With Massive Holding Arm And Safety Lock, Zinc-Plated - Kukamet
Take advantage of the combination of a compact, galvanised design, a 191 mm solid holding arm and dependable clamping performance (up to 3,500 N) for smooth, repeatable fixturing in small to mid-size assemblies. Order the clamp directly via Metav Werkzeuge or consult the specialists for application support and rapid supply. Horizontal lever clamp 113 — horizontal clamp with 191 mm arm and safety lock The Horizontal lever clamp 113 is a compact industrial clamp designed for secure 90° mounting in jigs, fixtures and workstation fixturing for metalworking and general workshop use. Galvanised steel construction 191 mm solid holding arm 90° angle-foot mounting Safety lock with high holding force Consistent clamping performance that keeps production moving The 113 lever clamp delivers reliable clamping with a maximum clamping force of 3,500 N and a holding force of 3,650 N, ensuring workpieces remain stable during machining, welding or assembly. These figures describe the difference between applied clamp force and sustained holding capacity: the former refers to the maximum force exerted when the lever is actuated, the latter to the sustained resistance against displacement. The compact form factor and low mass (approx. 0.94 kg) mean this clamp integrates easily into existing fixtures without adding excessive dead weight, contributing to faster cycle times and reduced fixture inertia. Space‑saving design and quick setup for workshop efficiency A short 191 mm arm and a 90° angle‑foot mounting allow the clamp to be positioned close to the workpiece and mounted in tight toolrooms or fixture plates. The galvanised finish gives corrosion resistance for long service life in daily use, while the solid holding arm and smooth lever action reduce set‑up time and permit repeatable positioning. For operations that demand frequent changeovers or multiple clamping stations, the compact horizontal form decreases interference with tooling and cutting paths, supporting uninterrupted workflow and maximised machine uptime. Robust safety features and material compatibility for practical use Built with a massive holding arm and an integrated safety lock, the clamp reduces the risk of unintentional release during processing and provides secure retention for medium‑duty applications. The galvanised steel construction is suitable for general workshop environments and offers durable surface protection. As a lever clamp suited to fixture and jig applications, it performs well on a range of workshop tasks where a sturdy, manually actuated clamp is required; the combination of robust mechanics and a positive locking feature supports operator confidence and safer handling in daily production. For secure, repeatable fixturing with the Kukamet Horizontal lever clamp 113, contact Metav Werkzeuge for tailored advice and prompt supply from Emmerich — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data SKU: 113-4-D-L-C3 GTIN: 8680731500974 Brand: Kukamet eClass: 21041719 ETIM: EC011973 Facts Arm length: 191 mm Maximum clamping force: 3,500 N Maximum holding force: 3,650 N Weight: 0.94 kg Mounting angle: 90° Special features Galvanised steel material Angle‑foot (Winkel‑foot) mounting Massive holding arm Safety locking mechanism Horizontal lever clamp design FAQ What is the maximum clamping force of this clamp? The Kukamet Horizontal lever clamp 113 offers a maximum clamping force of 3,500 N and a holding force of 3,650 N for secure retention during machining and assembly. Which mounting orientation is recommended for this model? The clamp is designed for 90° angle‑foot mounting, making it suitable for horizontal fixtures and jig plates where a compact footprint is required. Is the surface treated for corrosion resistance? Yes, the clamp features a galvanised steel finish that provides enhanced corrosion resistance for workshop environments. How heavy is the clamp and how does that affect fixture design? The clamp weighs approximately 0.94 kg, which keeps fixture deadweight low and simplifies handling during frequent changeovers. Does the clamp include a locking mechanism to prevent accidental release? The model includes a safety lock and a massive holding arm, offering a positive retention feature to prevent unintentional opening during operations. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 191mm Horizontal Clamp With Solid Holding Arm, 3.65kN Hold Force, Galvanised - Kukamet
Take advantage of a robust, zinc‑plated horizontal clamp that combines a massive holding arm, reliable clamping forces and compact installation to keep fixtures secure and processes uninterrupted. Order the clamp directly via Metav Werkzeuge or contact the consultants for technical advice and delivery options. Horizontal clamp 113 by Kukamet — zinc‑plated horizontal toggle clamp, 90° fixed angle The Horizontal clamp 113 secures workpieces at a 90° angle with a massive holding arm and zinc‑plated finish for reliable workshop and jig use Massive holding arm for secure clamping Zinc‑plated corrosion‑resistant finish 90° fixed angle for consistent positioning Holding force 3,650 N and clamping force 3,500 N Faster, repeatable clamping that reduces set‑up time The horizontal toggle provides consistent locking behaviour so cycle times are shortened and rework is reduced. With a high holding force and repeatable kinematics, the clamp maintains the same pressure every cycle, improving machining accuracy and operator confidence. The mechanical design enables quick manual actuation while stabilising the workpiece during light to medium operations, translating into measurable efficiency gains on production benches and assembly jigs. Built for longevity: corrosion resistance and sturdy construction Corrosion protection and robust components extend service life in busy workshops. The zinc‑plated surface slows surface degradation in humid or mixed‑use environments, while the massive arm resists bending and wear during repeated clamping. The solid construction means fewer replacements and lower maintenance overheads compared with lighter, stamped alternatives, supporting a reliable toolroom inventory and long‑term cost control. Compact mounting and versatile fixture integration A compact footprint and angle‑base mounting suit confined fixtures and retrofit applications, allowing secure installation without extensive rework of existing jigs. The 90° fixed orientation and a 191 mm arm length make the clamp suitable for repeatable edge and face clamping tasks. Lightweight assembly and standard mounting holes simplify retrofitting into existing assemblies; if uncertain whether this variant fits a specific fixture, technical advisors can clarify compatibility and suggest alternatives. Practical benefits for everyday workshop use The clamp delivers pragmatic advantages: faster throughput, safer workholding and dependable repeatability under routine loads. Thanks to the compact design and clear mechanical limits, setup errors are reduced and operator training time is minimised. Combined with supply reliability and product screening from Metav, this toggle clamp supports uninterrupted operations and predictable tool performance in both small workshops and larger production environments. Contact Metav Werkzeuge for tailored advice, fast supply and secure sourcing of Kukamet horizontal clamps to match production requirements Technical data Article number: 113-4-D-C3 GTIN: 8680731500943 Model: 113 Brand: Kukamet Core specifications Arm length: 191 mm Angle: 90° Clamping force: 3,500 N Holding force: 3,650 N Weight: 0.98 kg Materials & features Zinc‑plated material Massive holding arm Mounting: angle foot Suitable for lever‑type clamping (toggle clamp) eClass: 21041719 ETIM: EC011973 FAQ What maximum clamping force does this clamp provide? The Kukamet horizontal clamp 113 provides a clamping force of 3,500 N and a holding force of 3,650 N (SKU 113-4-D-C3) for secure workpiece retention in typical jigging and assembly tasks. Is the surface protected against corrosion? Yes, the clamp is zinc‑plated, which provides enhanced corrosion resistance for workshop environments and helps extend the component's service life. Can the clamp be fitted to existing fixtures with limited space? The compact design and angle‑foot mounting allow straightforward integration into constrained fixtures; the 191 mm arm length offers reach while keeping the overall footprint small. Which applications suit this type of toggle clamp? The device is suited to repetitive clamping tasks such as assembly jigs, light machining and inspection fixtures where a 90° fixed clamp orientation and reliable repeatability are required. Is the clamp durable under frequent use? Constructed with a massive holding arm and robust zinc plating, the clamp is designed for repeated operation with minimal deformation and predictable clamping behaviour. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 2000 N Pneumatic Clamp With Massive Hold Arm, Galvanised - Kukamet
Combine the robust 167 mm arm, galvanised construction and up to 2,500 N holding force to secure fixtures reliably and reduce setup times. Benefit from rugged pneumatic actuation and vertical-foot mounting for rapid, repeatable clamping — order the clamp directly via Metav Werkzeuge or consult the specialists for integration advice. Kukamet 651 Pneumatic Toggle Clamp – 2,500 N holding force, 167 mm arm The 651 is a pneumatic toggle clamp engineered for repetitive production clamping and jigs, delivering quick actuation and a 90° clamping angle with vertical-foot mounting for secure bench or fixture integration. Robust 167 mm holding arm Galvanised corrosion protection 2,500 N maximum holding force Vertical-foot mounting, 90° clamping angle Reliable high-force clamping for production environments The pneumatic toggle clamp provides consistent, measurable clamping performance that supports efficient machining and assembly. With a maximum holding force of 2,500 N and an actuation capacity up to 2,000 N, the device ensures workpieces remain immobile during secondary operations. The long 167 mm arm increases lever reach for deeper engagement while the massive holding arm construction minimises deformation and deflection under load. This combination reduces rework and improves process capability by lowering positional variation in fixtures. Technical distinctions such as the difference between actuation force and holding force are important: the pneumatic drive generates the actuation input, whereas the mechanical toggle multiplies this into a higher, sustained clamping load, delivering secure fixation without overloading the actuator. Designed for durability and straightforward integration into fixtures Corrosion resistance and robust mounting options extend service life and simplify installation. The clamp is finished in galvanised steel to resist workshop environments and maintain reliable surface properties over time. A vertical-foot mounting plate allows direct attachment to t-slots, plates or fixture bases, while the 90° clamping angle provides a low-profile solution for vertical or horizontal tooling arrangements. The reinforced arm and welded components are specified for industrial use, translating into lower maintenance frequency and predictable lifetime costs. Where space and alignment matter, the clamp’s defined geometry reduces the need for additional support hardware, saving assembly time and enabling compact fixture layouts. Fast, controllable actuation that improves throughput Pneumatic actuation delivers short cycle times and repeatable motion, making the clamp suitable for automated and semi-automated lines. The toggle mechanism converts compressed-air input into a secure clamping position quickly and with minimal operator effort, supporting higher cycle counts and reduced takt times. The massive holding arm and mechanical interlock improve safety against accidental release during vibration or shocks common in production. Integration with pneumatic control valves and simple exhaust-line fittings allows easy commissioning. For teams refining process flow, the unit’s predictable behaviour under varying air pressures enables straightforward tuning of clamp timing and sequencing to match downstream operations. For robust, high-force clamping from Kukamet, contact Metav Werkzeuge in Emmerich for tailored advice and supply solutions. Technical data Article number: 651-3-D-C3 GTIN: 8682843521649 Model: 651 Brand: Kukamet Facts Arm length: 167 mm Maximum actuation force: 2,000 N Maximum holding force: 2,500 N Clamping angle: 90° Special features Galvanised steel Vertical-foot mounting Massive holding arm Pneumatic actuation Category: Clamp ECLASS: 21021004 ETIM: EC011973 FAQ What is the difference between the actuation force and holding force? The actuation force refers to the pneumatic input capacity (2,000 N) that drives the mechanism; the holding force is the effective clamping result (2,500 N) achieved through the toggle mechanics of the 651 pneumatic clamp. Can the clamp be mounted on standard t-slot plates? Yes, the 651 is supplied with a vertical-foot mounting arrangement suitable for attachment to t-slot plates and fixture bases, enabling straightforward integration into standard tooling setups. Is the clamp suitable for repetitive, high-cycle production? The pneumatic actuation and reinforced construction of this toggle clamp are designed for frequent cycling in production environments, offering fast actuation and long service life under typical workshop conditions. What materials and environments is the clamp prepared for? Finished in galvanised steel, the clamp resists corrosion in general workshop atmospheres and is intended for robust industrial use where durability and surface protection are required. How does the 167 mm arm affect clamping applications? The extended arm reach facilitates deeper engagement and improved leverage in fixtures, allowing secure clamping of larger or irregularly positioned workpieces while maintaining mechanical stiffness. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 2000 N Pneumatic Clamp With Massive Holding Arm, Zinc Plated, Vertical Base - Kukamet
Take advantage of a robust pneumatic clamping solution that combines high holding force, corrosion-resistant galvanised construction and compact installation for reliable fixture performance; order via Metav Werkzeuge or request advice from our consultants to ensure the right configuration for the application. Pneumatic Clamp 651 by Kukamet — Vertical‑foot mounting, 67 mm arm, 90° The Pneumatic Clamp 651 is a compact pneumatic hold‑down clamp designed for fixture and jig applications where consistent 90° clamping and a vertical‑foot mounting are required. Pneumatic actuation for fast cycle times 2500 N holding force for secure clamping Galvanised finish resists corrosion Massive holding arm for high rigidity Reliable clamping for repetitive production The unit delivers repeatable clamping through pneumatic actuation that converts compressed air into controlled linear force, making it suitable for medium‑ to high‑volume assembly and machining operations. With a 67 mm arm and a defined 90° clamping angle, the device secures workpieces with minimal setup variation, reducing rework and downtime. The combination of actuation and mechanical design supports consistent part positioning, which is essential for automated or semi‑automated lines seeking measurable process stability. Strong hold and structural durability Engineered with a massive holding arm and a maximum holding capacity of 2500 N, the clamp ensures firm fixation even under lateral loads. The quoted actuation force of 2000 N provides an efficient transfer into the clamping element; the result is a high clamping force relative to footprint. The galvanised material offers a maintenance‑friendly surface that slows corrosion, preserving clamping geometry and service life in workshop environments where exposure to coolant or ambient humidity occurs. Compact mounting that integrates with fixtures Vertical‑foot mounting facilitates low‑profile installation at the edge of jigs or on fixture plates without compromising base‑plate access. The compact construction supports close part spacing and efficient use of workbench real estate. Where tooling designers need to maintain a clear tool path or integrate sensors and tooling stops, the vertical mounting and short arm length deliver installation flexibility while keeping the clamping vector predictable for process planning. Operational benefits and application guidance The clamp is suited to metalworking and general workshop environments that require secure, repeatable holds—examples include assembly, welding tacks, and secondary machining operations. The simple pneumatic control enables integration with common valve systems and PLC logic to achieve fast cycle times and safe interlocks. For users less familiar with pneumatic sizing, specifying supply pressure and valve response will determine cycle speed; the clamp’s mechanical data support straightforward system engineering and predictable performance. Contact Metav Werkzeuge for tailored application advice and to arrange supply of the Kukamet Pneumatic Clamp 651 (SKU 651-3-D-C1) for reliable, high‑force clamping in production environments — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data SKU: 651-3-D-C1 eClass: 21021004 ETIM: EC011973 Numbers / Core technical data Arm length: 67 mm Max actuation force: 2000 N Max holding force: 2500 N Clamping angle: 90° Design / Special features Vertical‑foot mounting Massive holding arm Galvanised finish Pneumatic actuation Category: Clamps (Spanner) FAQ What is the maximum holding force of this clamp? The Kukamet Pneumatic Clamp 651 offers a maximum holding force of 2500 N, suitable for secure fixation in many workshop and light industrial applications. How is the clamp mounted to a fixture plate? Mounting is by a vertical‑foot arrangement designed for secure installation at the edge of jigs or on fixture plates, enabling compact placement and clear tool paths. Is the surface treated to resist corrosion? Yes, the clamp is supplied with a galvanised finish that improves resistance to corrosion and supports longer service life in damp or coolant‑exposed environments. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 2000 N Pneumatic Clamp With Vertical Handle And Massive Arm, Galvanised - Kukamet
Combine a galvanised body with a 90° orientation and a vertical handle to achieve secure, repeatable clamping with up to 2,500 N holding force; order the clamp directly via Metav Werkzeuge or consult our specialists for integration advice. 651 Pneumatic clamp — vertical handle, galvanised construction, 90° orientation by Kukamet The 651 pneumatic clamp is a vertical-foot, right-angle clamping solution designed for fixture plates, jigs and automated workholding where compact, reliable clamping is required. Vertical handle for compact control Galvanised body for corrosion resistance 90° orientation for right-angle fixturing 2,500 N clamping force Reliable clamping performance for production use The unit delivers a consistent 2,500 N holding force with an actuation capacity of 2,000 N, providing a clear safety margin for medium-duty workholding. Pneumatic actuation enables fast cycle times and repeatable strokes, which reduces variability in batch production and supports stable machining results. The technical difference between actuation force and holding force is useful in design: actuation describes the force applied by the cylinder, while holding force indicates the maximum secure clamping load once the clamp is engaged. This separation ensures planners can size the actuator and supply pressure appropriately while preserving workpiece integrity. Built to last in demanding workshop environments Constructed from galvanised steel with a massive holding arm, the clamp resists corrosion and mechanical wear in industrial settings. The robust design minimises deflection under load and extends service life in repetitive production tasks. A compact arm length of 67 mm reduces intrusion into the workspace while still providing ample reach to secure components. The vertical-foot mounting simplifies integration into fixture plates and tooling blocks, allowing secure bolting and straightforward alignment in existing setups. Simple integration into automated cells and jigs Designed for a 90° clamping orientation, the clamp is suited to right-angle fixtures and pallets where space is constrained. The pneumatic mechanism and vertical handle allow reliable actuation from standard compressed-air supplies, enabling direct connection to solenoid valves and pneumatic control lines. The compact footprint and clear mechanical function make the component appropriate for retrofit projects and new automation designs alike, reducing engineering time for layout and signalling. Where cycle consistency matters, pneumatic actuation contributes to predictable process timing. Practical advantages for maintenance and workshop use The solid construction and straightforward mounting reduce the need for frequent adjustments, delivering low operational downtime. The vertical handle and accessible mounting points allow quick installation and inspection during routine checks. The absence of complex electronic control on the clamping unit itself keeps maintenance tasks mechanical and tangible, while the physical design supports easy replacement of wear parts when required. Technical documentation supplied with the component can be referenced during commissioning to confirm torque settings and mounting geometry. Contact Metav Werkzeuge for tailored advice on integrating the Kukamet 651 pneumatic clamp into fixtures and automated cells — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for technical consultancy and supply options Technical data Article number: 651-3-H-D-C1 Manufacturer: Kukamet Facts Arm: 67 mm Max actuation force: 2,000 N Max holding force: 2,500 N Angle: 90° Mounting: vertical foot SKU: 651-3-H-D-C1 ECLASS: 21021004 ETIM: EC011973 Special features Galvanised material Vertical handle Massive holding arm Right-angle (90°) clamping orientation Senkrechter Fuß (vertical foot) mounting FAQ What clamping capacity does this unit provide? The Kukamet 651 pneumatic clamp provides a holding force of up to 2,500 N, with an actuation force of 2,000 N specified for sizing the pneumatic supply. Is the clamp suitable for automated production cells? Yes, the pneumatic actuation and compact 90° orientation of the clamp make it well suited for integration into automated fixtures and pallet systems. What material is the clamp made from and how does that affect durability? The clamp is galvanised, which improves corrosion resistance and contributes to longer service life in workshop environments. How is the clamp mounted to a fixture plate? Mounting is via a vertical foot arrangement that secures the unit to the fixture plate, providing a compact and stable attachment for right-angle clamping setups. Can the clamp reach into tight spaces while maintaining stability? With a 67 mm arm and a massive holding arm design, the clamp offers a balance of reach and rigidity suitable for constrained tooling areas. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 2000 N Pneumatic Clamping Arm, Massive Hold Arm, Zinc-Plated, 2500 N Hold Force - Kukamet
Benefit from a robust clamping solution that combines a massive holding arm, a vertical-foot base and a galvanised finish for reliable performance on production jigs. With a maximum holding force of 2,500 N and an actuation force of 2,000 N, the unit secures workpieces consistently; order the Pneumatic clamp 651 via Metav Werkzeuge or consult our specialists for integration advice. Pneumatic clamp 651 — vertical-foot design with massive holding arm (Kukamet) The Pneumatic clamp 651 is a vertical-foot clamping device engineered for secure, repeatable workpiece fixation in jigs, fixtures and assembly lines. Massive holding arm for high rigidity Vertical-foot mounting for compact fixtures Holding force up to 2,500 N Galvanised finish for corrosion resistance Secure clamping that keeps production moving The unit delivers consistent holding force through pneumatic actuation, providing a measurable improvement in process stability. The combination of a massive holding arm and a vertical-foot mounting reduces vibration and movement during machining and assembly, which decreases rework and scrap rates. The design supports a clear clamping angle of 90°, ensuring that forces are applied in a controlled direction for repeatable results on jigs and fixtures. Durable construction for long service intervals Constructed with a galvanised finish, the clamp resists corrosion in workshop environments and maintains surface quality over time. The robust arm, specified at 117 mm, minimises deflection under load and extends service intervals by protecting critical contact points. These features translate into lower maintenance downtime and predictable component life, helping to sustain throughput without unexpected interruptions. Fast integration into existing setups The vertical-foot configuration simplifies mounting to plates and tooling plates where space is limited. Pneumatic actuation offers rapid cycle times and straightforward control integration with standard compressed-air systems. The design's maximum actuation force of 2,000 N pairs with the high holding capacity to provide an efficient clamp cycle that is compatible with automated and manual workstations alike. Versatile application across production tasks Engineered for general clamping duties within industrial workshops, the device suits a range of fixturing tasks that demand secure fixation and quick release. The unit’s properties make it appropriate for repetitive assembly, light machining and inspection fixtures where a reliable mechanical interface is required. The compact footprint and standard pneumatic control allow for straightforward adaptation into existing tooling concepts. For heavy-duty clamping requirements, contact Metav Werkzeuge to specify the Kukamet Pneumatic clamp 651 (SKU 651-3-D-C2) for production use or to request tailored technical guidance — Metav Werkzeuge GmbH, info@metav-werkzeuge.com, +49 2822 7131930. Technical data Article number: 651-3-D-C2 Manufacturer: Kukamet Designation: Pneumatic clamp 651 ECLASS: 21021004 ETIM: EC011973 Core technical data Maximum holding force: 2,500 N Maximum actuation force: 2,000 N Arm length: 117 mm Clamping angle: 90° Special features Vertical-foot mounting Massive holding arm Galvanised material Category: Spanner / Pneumatic clamp FAQ What maximum holding force does the clamp provide? The Kukamet Pneumatic clamp 651 offers a maximum holding force of 2,500 N, providing secure fixation for many fixturing tasks. How is the clamp mounted to a fixture? Mounting is via the vertical foot, which is designed for direct attachment to tooling plates and compact fixture bases. What actuation method is used and what force is required? The device uses pneumatic actuation with a reported maximum actuation force of 2,000 N, suitable for integration with standard compressed-air systems. Is the clamp suitable for harsh workshop environments? Yes; the galvanised finish provides enhanced corrosion resistance, increasing longevity in typical workshop conditions. Which applications are typical for this type of clamp? Typical uses include jigs, fixtures, assembly stations and light machining setups where reliable, repeatable clamping is required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 2000N Pneumatic Clamp With Vertical Handle And Massive 117mm Arm, Zinc Plated - Kukamet
Take advantage of robust pneumatic actuation, a vertical handle and a massive holding arm for dependable 90° workholding; the combination of clear force ratings and galvanised construction ensures consistent production performance. Order the unit directly via Metav Werkzeuge or consult Metav's specialists for integration advice. 651 Pneumatic clamp — vertical-handle toggle clamp with 90° mounting (Kukamet) 651 is a pneumatic toggle clamp intended for secure 90° fixture mounting in production and assembly environments, offering a compact 117 mm arm and galvanised construction for long-term service. Vertical handle for upright operation Massive holding arm for high rigidity Up to 2,500 N holding force Galvanised corrosion protection High clamping force for precise, repeatable holds The pneumatic mechanism delivers a defined actuation force of 2,000 N, which in combination with the clamp geometry produces a holding force of 2,500 N. This ratio of actuation to holding force ensures reliable workpiece retention during machining, assembly or testing cycles. By using pneumatic power for the closing motion, the device offers fast, consistent clamping action and reduced operator variability. The measured force values provide a verifiable basis for fixture design and allow planners to calculate safety margins and cycle loads with confidence. Durable construction that reduces maintenance and downtime Constructed in galvanised material and fitted with a massive holding arm, the clamp is engineered for resilience in daily industrial use. The vertical handle and vertical foot mounting create a compact footprint and simplify integration into benches and jigs where space is limited. The 117 mm arm provides a balance between reach and rigidity, reducing deflection under load. Galvanising delivers corrosion resistance to extend service life in humid or workshop environments, reducing the need for frequent replacement and lowering lifecycle costs. Designed for fast integration and consistent throughput This toggle clamp supports quick installation into existing fixtures and is suitable for series production where reliable repeatability and short cycle times matter. The 90° orientation makes it a practical choice for perpendicular clamping tasks and indexing stations. With clear specification data and a compact form factor, the clamp simplifies fixture engineering and shortens commissioning. The supplied SKU (651-3-H-D-C2) and technical ratings aid purchasing and inventory processes, while the robust design contributes to fewer interruptions in the production flow. For specification support or to arrange supply of the Kukamet 651 pneumatic clamp (SKU 651-3-H-D-C2), contact Metav Werkzeuge for expert advice and rapid delivery from Emmerich — info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 651-3-H-D-C2 Brand: Kukamet eClass: 21021004 ETIM: EC011973 Facts Arm length: 117 mm Actuation force: 2,000 N Holding force: 2,500 N Angle: 90° Special features Vertical handle Massive holding arm Vertical foot mounting Galvanised material Robust toggle mechanism FAQ What maximum holding force does the clamp provide? The clamp achieves a holding force of up to 2,500 N as specified for the Kukamet 651 pneumatic clamp (SKU 651-3-H-D-C2). What is the actuation force required for the pneumatic mechanism? The pneumatic actuation is specified at 2,000 N, which produces the rated holding performance for the 651 clamp. How is the clamp mounted to a fixture? Mounting is by a vertical foot, designed for 90° orientation to integrate into perpendicular fixture setups. What materials and surface treatment are used? The clamp is supplied in a galvanised finish with a massive holding arm for improved corrosion resistance and structural stability. Which reference should be used when ordering or specifying this clamp? Use the SKU 651-3-H-D-C2 and the Kukamet 651 pneumatic clamp designation when ordering or requesting technical documentation. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 200mm Horizontal Clamp With Massive Holding Arm, 3.65kN Hold Force, Zinc-Plated - Kukamet
Take advantage of a compact, corrosion‑resistant clamp that combines a 200 mm reach, a massive holding arm and up to 3.5 kN clamping force for dependable fixture work. Order the clamp through Metav Werkzeuge or consult our specialists for application‑specific advice. Horizontal Clamp 112 by Kukamet — 200 mm reach, 3.5 kN clamping force Horizontal Clamp 112 is a sturdy, galvanised horizontal clamp for secure workpiece holding in assembly, welding and fixture applications Massive holding arm for enhanced stability Galvanised construction for corrosion resistance 200 mm reach for versatile clamping positions 3.5 kN clamping force, 3.65 kN holding capacity Built for endurance and steady clamping The clamp’s galvanised finish and massive holding arm deliver a durable solution for repetitive production tasks where resistance to corrosion and mechanical stress matter. The robust construction reduces deformation under load and keeps clamping geometry consistent over time, which supports repeatable setups and lowers rework rates. The combination of a reinforced arm and a vertical base provides a stable interface for jigs and fixtures, helping maintain alignment during welding or machining. Measured performance for reliable process integration With a reach of 200 mm and a rated clamping force of 3.5 kN (holding capacity 3.65 kN), the unit supplies predictable holding power for medium‑duty operations. These figures enable planners to select an appropriate clamp based on quantified load requirements rather than estimation. The compact weight of 0.844 kg and the 90° orientation make it suitable for confined fixtures and modular tooling plates, simplifying integration into existing production cells and reducing cycle‑time impact. Easy mounting and long‑term operational benefits The vertical foot mounting allows secure attachment to workbenches, fixtures or weldments without complex adapters. The galvanised surface reduces maintenance frequency and extends service life in humid or workshop environments. Where repeated clamping is required, the solid arm construction minimises wear and preserves clamping accuracy, supporting consistent quality and lower total cost of ownership over many production cycles. Contact Metav Werkzeuge for tailored mounting options or to discuss the Horizontal Clamp 112 for specific fixture designs — expert advice and fast, reliable supply from our Emmerich location Technical Data SKU: 112-4-D-C3 GTIN: 8680731500592 Manufacturer: Kukamet Category: Spanner Key Figures Weight: 0.844 kg Arm length: 200 mm Maximum clamping force: 3,500 N Maximum holding force: 3,650 N Angle: 90° eCl@ss: 21041719 ETIM: EC011973 Features & Versions Galvanised finish Vertical foot mounting Massive holding arm Category: horizontal clamp Storytrigger: lever clamp (hebelspanner) FAQ What is the primary application for this horizontal clamp? The Horizontal Clamp 112 is designed for secure workpiece holding in assembly, welding and fixture applications where a compact, robust clamp with corrosion protection is required. Can the clamp be mounted on custom jigs and fixtures? Yes, the vertical foot mounting enables secure attachment to benches, fixture plates or custom jigs; the 200 mm reach helps position the clamping force where needed. What materials is the clamp suitable for? The clamp is a general‑purpose horizontal clamp; suitability depends on the workpiece and clamping requirements — the galvanised construction ensures durability in workshop environments. How much clamping force does the unit provide? Rated clamping force is 3,500 N with a maximum holding capacity of 3,650 N, giving quantifiable performance for fixture planning and safety margins. Is special maintenance required to preserve performance? Routine inspection and cleaning keep the clamp reliable; the galvanised finish reduces corrosion and maintenance frequency, while the massive arm design minimises wear. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 200mm Horizontal Clamp With Solid Holding Arm, 3.65 kN Holding Force, Galvanised - Kukamet
Take advantage of the combination of a massive holding arm, zinc-plated durability and a compact 200 mm reach to secure workpieces reliably on fixtures; order the clamp directly via Metav Werkzeuge or ask our consultants for application advice. 111 Horizontal clamp by Kukamet — zinc-plated toggle clamp with 3650 N holding force The 111 horizontal clamp is a compact horizontal toggle clamp designed for secure, repeatable workpiece holding in jigs, fixtures and light assembly lines. Massive holding arm 3650 N maximum holding force Zinc-plated steel construction 200 mm reach with horizontal foot Reliable clamping that keeps production moving The clamp delivers a consistently high holding force of 3650 N and a maximum clamping force of 3500 N, which translates into dependable fixation during loading, machining or inspection. The robust, heavy-duty arm reduces the risk of slippage under transverse loads, and the horizontal mounting foot makes it straightforward to fit into existing jigs. For production planners, this means fewer rejects and less rework because components remain stable during processing. Built for durability and simple integration Constructed from zinc-plated steel, the unit resists corrosion in workshop environments and keeps maintenance requirements low. The straightforward toggle mechanism requires minimal adjustment once aligned, enabling quick cycle times and reduced setup effort. A 200 mm reach provides improved access where space is constrained, while the compact form factor allows multiple clamps to be positioned closely on fixtures, improving workholding flexibility without increasing footprint. Practical performance data for workshop use The device combines compact weight (0.847 kg) with a massive holding arm design to deliver high clamping performance without unnecessary bulk. The 90° arm angle is suited to conventional fixture geometries and reduces interference with neighbouring tooling. Because the clamp is zinc-plated and mechanically simple, routine inspection consists mainly of visual checks and occasional lubrication, which supports continuous operation with predictable maintenance intervals. Select Kukamet quality for robust, repeatable clamping and contact Metav Werkzeuge in Emmerich for tailored advice and order support — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: 111-4-D-C3 GTIN: 8680731500257 eClass: 21041719 ETIM: EC011973 Core specifications Weight: 0.847 kg Arm length (reach): 200 mm Maximum clamping force: 3500 N Maximum holding force: 3650 N Angle: 90° Materials & special features Material: zinc-plated steel Mounting: horizontal foot Special feature: massive holding arm Category: Spanner Manufacturer: Kukamet FAQ What is the maximum holding force of this clamp? The clamp provides a maximum holding force of 3650 N, suitable for secure fixation in many light to medium-duty jigs and fixtures. Can the clamp be mounted on existing fixture plates? Yes, the horizontal foot mounting is compatible with standard fixture plates and is intended for easy integration into jigs and tooling. Is the surface finish suitable for humid workshop environments? The zinc-plated steel finish offers corrosion resistance appropriate for typical workshop and assembly settings. What is the effective reach of the clamp arm? The clamp has a 200 mm arm reach, giving improved access for parts positioned away from the mounting base. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 200mm Horizontal Clamp With Solid Holding Arm, 3.65kN Holding Force - Kukamet
Take advantage of a robust lever design, high clamping force and compact footprint for reliable fixture clamping; order the horizontal clamp directly via Metav Werkzeuge or ask their consultants for application advice. Horizontal clamp 112 — Kukamet, 200 mm lever, up to 3,650 N holding force Horizontal clamp 112 secures workpieces in horizontal jigs and fixtures with a solid lever arm and a vertical-foot mount for stable attachment in production and workshop environments. Massive solid holding arm 200 mm lever for extended reach Clamping force up to 3,500 N Vertical-foot mounting for stability Fast, reliable clamping for repetitive production The horizontal clamp offers an immediate solution for repeatable holding tasks: its lever geometry converts operator action into a consistent clamping force of up to 3,500 N, while the maximum holding force is 3,650 N, ensuring components remain fixed during machining, assembly or inspection. This consistent performance reduces setup variation and the need for rework, so cycle times remain predictable. The mechanism is designed for fast engagement and disengagement, supporting lean workflows in small-batch and series production alike. Robust construction that stands up to workshop use Built with a massive solid holding arm and a durable blackened finish, the clamp withstands abrasive and oily shop conditions without appearing corrosive at first signs of use. The vertical-foot mounting provides a secure base that minimises vibration transfer to the workpiece and fixture plate. At a weight of 0.844 kg, the device balances rigidity with a compact footprint, allowing integration into existing jigs without significant strengthening of carrier plates or tooling plates. Practical integration and straightforward handling Designed as a horizontal lever clamp suitable for fixtures, the device fits into manual and semi-automatic assemblies where a right-angle clamping action is required (90° actuation). The extended 200 mm arm provides added reach for clamping over obstructed or uneven surfaces, while the toggle-style action keeps the arm locked under load for safe handling. For workshop engineers and maintenance planners, the unit simplifies fixture design and supports repeatable quality control in assembly and light machining operations. For secure, high‑force horizontal clamping from a trusted partner, contact Metav Werkzeuge for Kukamet products — Metav IndustryLine supplies and supports this clamp; email info@metav-werkzeuge.com or call +49 2822 7131930 for technical advice and ordering. Technical data Article number: B112-4-D-C3 GTIN: 8680731507300 Model: 112 Facts Arm length: 200 mm Clamping force (max): 3,500 N Holding force (max): 3,650 N Angle: 90° Weight: 0.844 kg Special features Massive holding arm Vertical-foot mounting Blackened finish Horizontal toggle/lever clamp Category: Clamps FAQ What clamping force can be expected from this clamp? The clamp provides a clamping force of up to 3,500 N and a holding force of 3,650 N as specified for the Kukamet horizontal clamp 112. How is the clamp mounted to a fixture plate? Mounting is by a vertical-foot arrangement that secures the clamp to the fixture plate for stable, low-vibration clamping. Is the lever arm suitable for obstructed workpieces? Yes, the 200 mm lever gives extended reach for clamping over partially obstructed components and uneven surfaces. What surface treatment does the clamp have and why does it matter? The unit has a blackened finish which offers basic protection against wear in workshop environments and helps to reduce visible marks on the component support. Can this clamp be used in automated fixtures? The toggle-style mechanism and compact footprint make the clamp suitable for integration into manual and semi-automatic fixtures where horizontal clamping action is required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 200mm Horizontal Clamp, Massive Holding Arm with Safety Lock, 3.65 kN Hold Force - Kukamet
Take advantage of robust clamping performance, a massive holding arm with safety lock and a compact design that simplifies fixture layout. Order the clamp directly via Metav Werkzeuge or contact the consultants for configuration advice. Horizontal clamp 112 — Kukamet — robust lever clamp with safety lock and 200 mm arm Horizontal clamp 112 is a lever-style horizontal clamp designed for secure workholding in jigs, fixtures and bench mounting where repeatable clamping and quick operation are required. Massive holding arm with safety lock 3,650 N maximum holding force 200 mm arm for extended reach Vertical foot for secure mounting Consistent clamping power to reduce rework and increase uptime The clamp delivers a high and reliable holding force—rated at 3,650 N—with a corresponding closing force of 3,500 N, providing stable fixation for machining, assembly and inspection tasks. High, measurable forces reduce part movement during operations, which lowers scrap rates and minimises repeat runs. The numeric ratings enable planners and engineers to calculate fixture safety margins and select the clamp where the force figures match the application requirements. For users familiar with clamping technology, these values indicate suitability for medium-duty production and repetitive handling environments. Robust construction and integrated safety for everyday workshop use A massive holding arm combined with an integrated safety lock ensures that the clamp remains secure under load and during process interruptions. The component is finished in a blackened finish, which offers basic corrosion resistance and a professional appearance on the shop floor. The supplied design features a vertical foot for bench or fixture mounting and a fixed 90° lever orientation, which supports compact layouts and straightforward mechanical integration. These construction details translate into predictable wear behaviour, easier inspection intervals and a longer service life compared with lightweight alternatives. Easy integration into jigs and fixtures with defined reach and compact mass With a 200 mm arm, the clamp provides additional reach for larger workpieces or for positioning behind obstructing components while keeping a modest mass of 0.73 kg, which simplifies balancing of moving subassemblies. The lever-action mechanism enables fast clamping and unclamping cycles, shortening process times and improving throughput when integrated into assembly lines or test rigs. Installation is simplified by the vertical foot mounting; the design is compatible with conventional fixture plates and can be secured with standard fasteners. Clear, quantitative values for arm length, forces and angle support straightforward CAD integration and process planning. Select the Kukamet 112 horizontal clamp for dependable, measurable clamping performance — contact Metav Werkzeuge for supply and technical assistance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: B112-4-D-L-C3 Name: Horizontal clamp 112 Manufacturer: Kukamet Facts Arm length: 200 mm Max closing force: 3,500 N Max holding force: 3,650 N Weight: 0.73 kg Angle: 90° Special features Vertical foot mounting Massive holding arm Safety lock Blackened finish Lever-style horizontal clamp FAQ What clamping force can be expected from this clamp? The Kukamet horizontal clamp 112 offers a maximum holding force of 3,650 N and a closing force of 3,500 N, figures that support medium-duty fixturing and repetitive assembly tasks. Can the clamp be mounted to a workbench or fixture plate? Yes, the clamp features a vertical foot for secure mounting to bench tops or fixture plates using standard fasteners. Does the clamp include any safety mechanism to prevent accidental release? A built-in safety lock is integrated into the design to hold the lever in place under load and prevent unintended opening. What reach does the clamp provide for offset or recessed workpieces? The lever arm extends to 200 mm, giving improved reach behind obstructions and flexible placement within jigs and fixtures. Is the finish suitable for workshop environments? The blackened finish offers basic corrosion resistance and a durable surface for everyday workshop use. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 200mm Horizontal Toggle Clamp, Massive Arm And Safety Lock, Galvanised - Kukamet
Secure, repeatable clamping with a 200 mm solid arm and galvanised construction; benefit from up to 3,650 N holding force combined with a built-in safety lock for safe operation. Order the Kukamet horizontal toggle clamp 111 directly via Metav Werkzeuge or consult our team for application advice. Horizontal toggle clamp 111 — 200 mm arm, galvanised finish (Kukamet) The Horizontal toggle clamp 111 is a durable horizontal lever clamp designed for secure workholding in metalworking, assembly and general workshop applications. 200 mm solid holding arm Galvanised steel for corrosion resistance Horizontal base for easy bench mounting Safety locking mechanism for secure clamping Consistent clamping force for production environments The clamp delivers a reliable holding force of 3,650 N and a maximum operating thrust of 3,500 N, providing the mechanical certainty required for repetitive tasks. The lever mechanism converts operator effort into a firm, repeatable clamp action, which reduces repositioning and cycle time. Specified forces are a decisive factor when securing components for machining, drilling or welding; the numeric values enable straightforward selection against fixture requirements and process tolerances, ensuring the clamp meets production demands. Simple mounting and robust build minimise downtime Fitted with a horizontal base, this clamp is intended for easy bench or fixture mounting, allowing fast integration into jigs and assembly lines. The solid holding arm and galvanised finish offer resistance against mechanical wear and corrosion in busy workshop environments. A visible safety lock retains the clamp in the closed position, preventing accidental release during handling. These design choices reduce maintenance intervals and help maintain uptime, which supports steady throughput on the shop floor. Practical design that supports operator safety and versatility The 90° arm geometry and lever action enable secure engagement with a short operating stroke, making the clamp suitable where space is limited yet secure fixation is essential. The galvanised construction balances durability with affordability, delivering a corrosion-resistant surface without costly coatings. For fixtures that require quick manual clamping and dependable retention, this toggle clamp provides a compact, effective solution that fits standard workshop workflows while enhancing operator confidence through its locking feature. Contact Metav Werkzeuge for reliable supply and technical advice on the Kukamet horizontal toggle clamp 111 — email info@metav-werkzeuge.com or call +49 2822 7131930 to verify suitability and delivery from Emmerich Technical Data Article number: 111-4-D-L-C3 GTIN: 8680731500288 Manufacturer: Kukamet SKU: 111-4-D-L-C3 eClass: 21041719 ETIM: EC011973 Facts Arm length: 200 mm Holding force: 3,650 N Maximum thrust: 3,500 N Weight: 0.73 kg Clamping angle: 90° Special features Galvanised material Horizontal base mounting Solid/massive holding arm Safety locking mechanism Designed as a lever/lever-action clamp FAQ What holding force can be expected from this clamp? The Kukamet horizontal toggle clamp 111 provides a holding force of up to 3,650 N and a maximum thrust of 3,500 N, suited for medium-duty workholding. Which mounting method is used for installation? Mounting is via a horizontal base designed for bench or jig attachment, enabling straightforward integration into existing fixtures. Is the clamp suitable for corrosive workshop conditions? Yes, the galvanised finish of the clamp offers enhanced corrosion resistance for standard workshop environments. Can the clamp be used for repetitive machining operations? The lever mechanism and robust construction make the clamp well suited for repetitive tasks, offering consistent clamping and reduced repositioning time. What safety features are included? A mechanical safety locking mechanism secures the clamp in the closed position, preventing unintended release during handling or machining. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 200mm Pneumatic Clamp With Vertical Handle And Solid Arm, 3000N Push / 3300N Hold, Zinc-Plated - Kukamet
Benefit from 3.3 kN holding power, a massive zinc-plated arm and an ergonomic vertical handle for reliable, repeatable clamping in medium-duty production environments. Order the Pneumatic clamp 651 directly via Metav Werkzeuge or ask our consultants if needed. Pneumatic clamp 651 — Vertical handle, 3.3 kN holding force (Kukamet) Pneumatic clamp 651 is a workshop-grade pneumatic clamping device designed for secure fixturing at a 90° angle, suitable for assembly fixtures and production jigs. Vertical handle for easy operation Massive holding arm for stable clamping 3.3 kN maximum holding force Zinc-plated corrosion protection Consistent clamping force for dependable throughput The clamp delivers a maximum holding force of 3.3 kN, backed by a pneumatic operating force of 3,000 N, which supports consistent workholding across repeat cycles. This level of force reduces vibration and part movement during machining, leading to fewer rejects and less rework. The pneumatic actuation enables fast, uniform strokes for improved cycle times in repetitive tasks, while the clear separation between operating and holding forces contributes to predictable performance on the shop floor. Robust construction built for workshop conditions Constructed with a zinc-plated finish and a massive holding arm, the unit resists corrosion and mechanical wear in demanding environments. The solid arm and 90° orientation provide a stable reaction path, minimising deflection under load. These design choices extend service life and lower lifetime maintenance needs, delivering a durable clamping solution where longevity and reliability are priorities. Ergonomic layout and straightforward integration Featuring a vertical handle and a vertical foot mounting plate, the clamp is intended for installation at bench level or within fixture frames where space is limited. The 200 mm arm gives a practical reach for a wide range of workpieces without compromising stability. The vertical handle supports intuitive operation during manual loading, and the compact base simplifies positioning in modular fixtures or conveyor-based assemblies. Efficient for automated and manual workflows Thanks to pneumatic actuation and a lever-style concept, the clamp suits both semi-automated stations and manual assembly points. The design supports fast engagement and consistent clamping, promoting steady throughput and repeatable positioning. Integration into pneumatic control loops is straightforward, making it a practical choice for production lines that require dependable, medium-force clamping without complex control systems. Contact Metav Werkzeuge for application advice and reliable supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 651-4-H-D-C3 Model: 651 Product: Pneumatic clamp Brand: Kukamet Mounting: vertical foot Facts Maximum operating force: 3,000 N Maximum holding force: 3,300 N Arm length: 200 mm Angle: 90° ECLASS: 21021004 ETIM: EC011973 Special features Zinc-plated material Massive holding arm Vertical handle and solid holding arm Lever clamp design (hebelspanner) Material: Verzinkt FAQ What clamping force can be expected from this clamp? The Pneumatic clamp 651 offers a maximum holding force of 3,300 N and a pneumatic operating force of 3,000 N, providing reliable fixation for medium-duty applications. How is the clamp mounted in a fixture? Mounting is via a vertical foot; the clamp is designed for vertical-foot installation in bench fixtures or frame-mounted jigs. Which materials is the clamp suitable for handling? The clamp’s robust arm and zinc-plated finish make it suitable for typical workshop materials handled in assembly and light machining operations. Is the arm length sufficient for small to medium workpieces? With a 200 mm arm, the clamp provides practical reach for many small to medium components while maintaining stability under load. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 229mm Horizontal Clamp With Solid Holding Arm, 4 500 N Thrust / 5 000 N Hold - Kukamet
Benefit from a compact, heavy‑duty clamp that combines a 229 mm arm with a 5,000 N holding force and a robust blackened finish for dependable, repeatable workholding. Request tailored advice or place an order via Metav Werkzeuge for fast supply and local support. 111 horizontal clamp by Kukamet — 229 mm arm, 5,000 N holding force The 111 is a horizontal lever clamp designed for secure workholding in jigs, fixtures and production tooling where reliable repeatability and quick operation are essential 229 mm reach for extended clamping 5,000 N maximum holding force Robust blackened finish Horizontal-foot mounting at 90° Reliable clamp performance for production environments The lever design delivers a high holding force while remaining quick to operate, providing a dependable clamp for repetitive tasks. With a rated holding force of 5,000 N and a clamping force of 4,500 N, the unit ensures components are held securely during machining, assembly or inspection cycles. These measurable values support process planning and risk assessment in production lines, enabling planners to size clamps to the required safety margins and avoid slippage during operations. Durable construction that reduces downtime A massive holding arm and blackened finish create a combination of strength and surface protection that suits workshop conditions. The finish (blackened burnish) helps resist corrosion and conceal wear from regular handling, while sturdy arm construction limits deformation under load. A total weight of 1.58 kg balances robustness with ease of handling, keeping fixtures manageable during set-up and maintenance and reducing the need for frequent replacements. Space-saving mounting with precise positioning The clamp’s horizontal foot mounting and 90° angle are engineered for integration into fixtures where lateral clamping is required. The 229 mm arm gives extended reach for larger or offset workpieces without increasing the overall footprint of the jig, which supports compact station design and easier access for operators. The mounting style simplifies installation into standard plates or tooling blocks and supports repeatable positioning across multiple workstations. Fast operation and low-maintenance handling As a lever clamp in the toggle family, the mechanism enables quick engagement and release with clear tactile feedback, speeding up cycle times on assembly and machining processes. The simple mechanical design means routine upkeep is limited to periodic inspection and lubrication of pivot points rather than complex servicing. This straightforward maintenance profile contributes to consistent uptime and predictable lifecycle costs for production tooling. For procurement or technical integration of Kukamet clamping solutions, contact Metav Werkzeuge in Emmerich for expert advice and secure supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: B111-5-D-C3 GTIN: 8680731507096 Manufacturer: Kukamet Model: 111 Weight: 1.58 kg Facts Arm length: 229 mm Angle: 90° Holding force: 5,000 N Clamping force: 4,500 N Special features Mounting: horizontal foot Finish: blackened (brünierte Oberfläche) Massive holding arm Category: lever clamp / horizontal clamp eClass: 21041719 ETIM: EC011973 FAQ What is the maximum holding capacity of this clamp? The clamp provides a maximum holding force of 5,000 N; the rated clamping force is 4,500 N for the Kukamet 111 horizontal clamp (SKU B111-5-D-C3). Is the clamp suitable for integration into production fixtures? Yes. The horizontal-foot mounting and 90° orientation allow straightforward integration into jigs and fixture plates for repeatable positioning. What finish does the arm have and how does it affect durability? The arm has a blackened finish that improves corrosion resistance and conceals surface wear, supporting longer service intervals in workshop environments. How large is the working reach of the clamp? The working reach is provided by a 229 mm arm, which extends access to offset or larger workpieces while keeping the fixture compact. Does the clamp require special maintenance or tools? Maintenance is limited to routine inspection and lubrication of pivot points; no specialised tools are required for standard upkeep of the Kukamet lever clamp. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fast, secure workpiece clamping with toggle clamps
Toggle clamps, also known as knee lever clamps or lever clamps, are mechanical clamping elements used to fix components quickly and reliably in fixture construction, assembly, welding and testing. Their kinematic knee lever principle provides a one-motion closure that locks beyond a mechanical dead centre, delivering consistent clamping force with minimal operator effort.
How the locking principle benefits production
The kinematic dead-centre action means the clamp self-locks once closed, so no continuous force is required on the handle and the workpiece remains form-stable even under process-induced vibration. That behaviour translates directly into higher process reliability and faster cycle times: operators close the clamp in one swift move, parts stay in position during machining or inspection, and changeover times are reduced.
Practical advantages for everyday workshop use
- Reduced set-up time through single-motion clamping
- Consistent repeatability and process stability under vibration
- High holding force with low operator effort thanks to the dead-centre mechanism
- Durable construction for long service life in repetitive production
- Versatile mounting options for vertical, horizontal, push‑rod and draw applications
Technical overview
- principle: kinematic knee lever (dead-centre) locking
- application areas: fixture construction, assembly, welding, testing
- design variants: vertical clamp, horizontal clamp, push-rod clamp, draw/closure clamp
- material: high-strength zinc-plated steel; stainless steel options
- handle: ergonomic, oil-resistant handles
- joints: wear-resistant joint bushes
- process suitability: holds under strong, process-induced vibration; enables high repeatability
Metav as your precision partner
Metav combines decades of specialist knowledge with a broad, dependable assortment for industry and trade. With more than 48,000 customers, a catalogue exceeding 250,000 products and a quality filter based in Emmerich, Metav offers a practical, low-risk route to robust toggle clamps and accessories—ideal for buyers who need dependable stock, expert selection and consistent product quality.
In short: toggle clamps (knee lever clamps / lever clamps) deliver rapid, repeatable clamping with minimal operator effort, making them a straightforward productivity upgrade for demanding production environments.
FAQ
What exactly is a toggle clamp and how does it lock?
A toggle clamp uses a kinematic knee lever that passes a mechanical dead centre during closure; once over‑centre, the clamp self-locks, maintaining clamping force without continuous pressure on the handle.
Which toggle clamp type should I choose for sheet assembly or for pulling covers together?
Use vertical or horizontal toggle clamps for holding sheets and assemblies; choose draw/closure clamps when axial pulling or form closing is required. The variety of toggle clamp designs matches different fixture geometries and force directions.
Are toggle clamps suitable for high-vibration processes?
Yes. The dead‑centre locking of toggle clamps secures the workpiece even under strong, process-induced vibration, ensuring positional stability during machining or testing.
What materials and handle options are available for toggle clamps?
Common materials: zinc-plated steel and stainless steel. Handles are typically ergonomic and oil-resistant; joints use wear-resistant bushes for extended service life.
Can Metav help specify the right toggle clamp for my application?
Metav supplies a wide selection of toggle clamps and technical information, enabling selection based on application, material and required holding force; the assortment is supported by decades of precision experience and a large customer base.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com