Quick, secure clamping with lever clamps
Lever clamps provide rapid, repeatable workholding for fixture building, assembly, welding and testing, using the kinematic knee-lever principle to deliver self-locking retention and resist process vibrations. Designed for metalworking applications and made from high-strength materials such as zinc-plated steel or stainless steel, these clamps reduce setup and handling times while enabling high holding forces with minimal operator effort. Available in vertical and horizontal versions as well as thrust bar and closure styles, lever clamps ensure consistent positioning, long service life and enhanced process reliability for serial production. Key advantages include self-locking mechanism, high repeatability, reduced setup time and robust construction.
90° 4500 N Pneumatic Vertical-Handle Clamp, Zinc-Plated, 5000 N Holding Force - Kukamet
Compact, corrosion-resistant and designed for secure fixture work: the Kukamet 651 combines a galvanised housing, a vertical base for straightforward mounting and a vertical handle to save space, delivering 4,500 N actuation and 5,000 N holding force for reliable clamping — order the product directly via Metav Werkzeuge or ask our consultants if needed. 651 Pneumatic clamp — vertical-foot design, 90° handle (Kukamet) The 651 pneumatic clamp is a compact pneumatic clamping solution intended for fixture and production-line applications where a right‑angled hold and robust retention are required. Pneumatically actuated for fast cycles Vertical handle for compact operation Galvanised finish for corrosion resistance 4,500 N actuation, 5,000 N holding Reliable clamping where repeatability matters The pneumatic actuation of this clamping unit provides a consistent clamping force that suits repetitive production tasks. With a maximum actuation force of 4,500 N and a maximum holding force of 5,000 N, the device is built to maintain secure fixation during machining, assembly or welding processes. The controlled, pneumatic operation reduces cycle variability when compared with manual lever clamps, enabling a more predictable throughput and fewer rejects. The relatively low mass of 3.9 kg supports installation in compact jigs without adding excessive weight. Robust construction for industrial environments Constructed from galvanised components, the clamp resists corrosion in workshop conditions and offers extended service life where occasional exposure to moisture or coolants occurs. The vertical base simplifies attachment to fixture plates, while the 90° handle orientation creates a clear load path and occupies minimal lateral space on the workbench. These mechanical choices reduce the need for frequent replacement and contribute to stable clamping geometry, which is essential for precision operations and repeatable part placement. Simple integration and practical maintenance The upright actuation concept with a vertical handle enables compact layouts on fixtures and jig assemblies. The clamp is supplied as a compact unit ready for pneumatic connection and mechanical fixing to a vertical baseplate. Routine maintenance is limited to standard pneumatic practice — checking supply cleanliness and connection integrity — which keeps downtime low and service requirements straightforward. Clear, measurable values for actuation and holding force aid planning when integrating the unit into automated or semi‑automated systems. Suited applications and process benefits Engineered for use in fixture construction and series production, the clamp supports fast cycle times and secure part retention where right‑angled clamping is necessary. The combination of a galvanised finish, defined clamping forces and compact mounting makes the device appropriate for jigs in metalworking and general workshop setups where robust, repeatable fixation is required. By specifying a component with known technical figures, process engineers and workshop managers gain transparency for layout and force calculations during fixture design. For tailored advice on Kukamet pneumatic clamps and reliable supply from Emmerich, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 651-5-H GTIN: 8682843521670 eClass: 21021004 ETIM: EC011973 Core specifications Weight: 3.9 kg Material: galvanised Mounting: vertical base Angle: 90° Arm: Not applicable Special features Vertical handle Pneumatic actuation Max. actuation force: 4,500 N Max. holding force: 5,000 N Compact design for fixture integration FAQ What maximum clamping force does the unit provide? The Kukamet 651 pneumatic clamp delivers a maximum actuation force of 4,500 N and a maximum holding force of 5,000 N for reliable fixation in production fixtures. How is the clamp mounted in a fixture? Mounting is achieved via the vertical base supplied on the unit; the vertical base allows secure attachment to fixture plates and jigbeds. Is the clamp suitable for humid workshop environments? The galvanised finish of the 651 provides corrosion resistance appropriate for typical workshop conditions, helping to extend service life. What is the weight and how does it affect fixture design? The clamp weighs 3.9 kg; its modest mass simplifies placement within jigs and minimises additional structural demands on the fixture. Does the clamp include a manual lever or is it fully pneumatic? Operation is pneumatic with a vertically oriented handle arrangement for compact actuation; manual lever operation is not part of the standard design. Which document should be consulted for integration details? Refer to the technical datasheet and the product catalogue page provided by Kukamet for mounting dimensions and pneumatic connection recommendations for the 651 pneumatic clamp (SKU 651-5-H). Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 5,000 N Horizontal Clamp With Right-Angle Base Zinc-Plated - Kukamet
Take advantage of the combination of robust clamping performance, galvanised durability and compact design to improve fixture reliability and reduce rework. Order the Horizontal clamp 113 directly via Metav Werkzeuge or consult our specialists for integration advice. Horizontal clamp 113 — galvanised horizontal clamp with 5,000 N holding force (Kukamet) The Horizontal clamp 113 is a galvanised lever-style clamp intended for stable 90° fixtures and jig applications, offering high clamping and holding forces with an angled base for secure mounting. Holding force 5,000 N for secure clamping Clamping force 4,500 N for high-pressure fixation Galvanised steel resists corrosion and wear Angle base fixed at 90° for consistent positioning Secure production through measurable clamping performance The clamp delivers a defined holding force of 5,000 N and a clamping force of 4,500 N, values that translate directly into reliable piece stability during machining and assembly. These figures reduce part movement, lower scrap rates and shorten setup times by enabling a predictable workholding environment. The forces are particularly relevant for repeatable fixtures and batch production, where reproducible results underpin throughput and cost-efficiency. Compact, corrosion-resistant design for durable jigs Constructed from galvanised steel, the unit withstands workshop atmospheres and maintains functional surfaces over time, reducing the need for frequent replacement. The angled base (Winkelfuß) and fixed 90° orientation simplify integration into existing jigs and plates, while the moderate mass of 1.84 kg balances solidity with ease of handling. These aspects support long service life and low maintenance, offering an economical route to dependable clamping. Straightforward integration and workshop versatility As a lever-style fixture component with an angle base, the clamp suits a wide range of applications from assembly benches to bespoke tooling frames. The compact footprint and clearly specified performance figures permit straightforward planning for fixture design and risk assessment. Identifiable by SKU 113-5 and a clear GTIN, the item can be logged into inventory systems and specified on engineering drawings for traceable part management. Contact Metav Werkzeuge to discuss Kukamet’s Horizontal clamp 113 for reliable fixture upgrades and bespoke integration advice from our specialists Technical data Article number: 113-5 GTIN: 8680731501001 Brand: Kukamet Core specifications Weight: 1.84 kg Holding force: 5,000 N Clamping force: 4,500 N Angle: 90° Mounting thread for pressure spindle: M12x80 Design & features Material: galvanised steel Mounting type: angled base (Winkelfuß) Arm: not applicable Special feature: none FAQ What clamping forces does the Horizontal clamp 113 provide? The Kukamet Horizontal clamp 113 delivers a holding force of 5,000 N and a clamping force of 4,500 N, enabling stable fixation for machining and assembly operations. Is the clamp suitable for corrosive workshop environments? Yes, the clamp is made from galvanised steel, which provides enhanced resistance against corrosion and extends service life in typical workshop conditions. How is the clamp mounted within a fixture? The unit uses an angled base fixed at 90°, designed for direct mounting to plates or jigs where consistent right-angle positioning is required. Can the clamp be specified in assembly documentation? Yes, the product can be referenced by SKU 113-5 and GTIN 8680731501001 for clear identification in bills of materials and engineering drawings. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 5,000 N Pneumatic Clamp Vertical Handle Massive Zinc Arm, 4,500 N Closing Force - Kukamet
Robust galvanised construction and a heavy holding arm ensure dependable, repeatable clamping with up to 5,000 N holding force and 4,500 N clamping force; the pneumatic actuation also delivers consistent cycle times for production environments. Order the Kukamet 651 directly via Metav Werkzeuge or consult our specialists for application support. 651 Pneumatic Clamp (Kukamet) – Vertical handle, galvanised heavy holding arm 651 is a pneumatic clamp for right-angle holding in jigs and fixtures, combining a vertical handle with a massive galvanised holding arm for secure positioning in assembly and machining setups Vertical handle for compact operation Heavy-duty galvanised holding arm 5,000 N maximum holding force 90° clamp angle for right-angle clamping Secure, repeatable clamping for production use The combination of pneumatic actuation and a long 230 mm arm delivers a measured balance between reach and force: with a maximum holding force of 5,000 N and a clamping output rated at 4,500 N, the device maintains consistent pressure cycle after cycle. This level of performance supports repeatability in high-volume tasks and reduces the need for readjustment during shift changes. Pneumatic control ensures strokes are uniform, which helps preserve tolerances on fixtures and mating parts. Built to withstand workshop conditions and minimise downtime Constructed from galvanised materials and fitted with a massive holding arm, the unit resists corrosion and mechanical wear in demanding environments. The vertical handle layout and solid arm design reduce flex under load, lowering the likelihood of unexpected maintenance. The robust design translates into longer service intervals and predictable tool life, supporting continuous operation on the shop floor and contributing directly to reduced unplanned downtime. Compact mounting and straightforward integration into fixtures Designed for a vertical foot mounting arrangement, the clamp occupies minimal lateral space and fits neatly into standard jig plates or dedicated fixtures. The 90° clamp orientation is particularly suited to right-angle clamping tasks in welding, assembly and machining fixtures. Integration is simplified by a clear mechanical interface; the pneumatic actuation can be incorporated into existing compressed-air circuits without complex controls, enabling a rapid set-up of automated or semi-automated stations. Practical advantages for industry and craft Engineered for metalworking and industrial assembly, the unit is suitable for production lines, toolroom jigs and fixture setups where secure, repeatable clamping is essential. The solid construction and measured force ratings make it appropriate for heavy-duty tasks while remaining manageable for smaller workshops that require industrial-grade reliability. Supplied via Metav Werkzeuge, the clamp benefits from a quality filter at the European logistics hub in Emmerich, backed by a wide product range and longstanding service expertise. Contact Metav Werkzeuge to discuss how the Kukamet 651 pneumatic clamp can increase clamping reliability on production lines and to arrange delivery from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: 651-5-H-D-C3 Manufacturer: Kukamet Core specifications Arm length: 230 mm Max clamping force: 4,500 N Max holding force: 5,000 N Clamp angle: 90° Materials and features Material: galvanised Vertical handle and massive holding arm Mounting: vertical foot Heavy-duty construction eClass: 21021004 ETIM: EC011973 FAQ What maximum holding force does the clamp provide? The Kukamet 651 pneumatic clamp provides a maximum holding force of 5,000 N, suitable for robust fixture applications. Is the clamping force delivered by pneumatic actuation adjustable? Yes, the pneumatic actuation of the 651 allows clamping force adjustment via pressure regulation in the compressed-air supply to match process requirements. What mounting method is required for installation? The unit uses a vertical foot mounting arrangement; the 651 is designed for secure attachment to jig plates or fixture bases in a vertical orientation. Can the clamp be used in corrosive workshop environments? The galvanised finish on the 651 offers enhanced corrosion resistance compared with plain steel, improving suitability for shop-floor conditions. Which industries and applications suit this clamp? The Kukamet 651 is intended for metalworking, assembly and welding fixtures where repeatable right-angle clamping is required; it is also applicable in automated production cells when integrated with pneumatic control systems. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 5,000N Horizontal Toggle Clamp With Safety Lock, Blackened Finish - Kukamet
Take advantage of a high holding force and a secure safety lock combined with a compact, horizontally mounted design to keep production cycles consistent and safe; order via Metav Werkzeuge or contact our consultants for technical guidance. Horizontal toggle clamp 111 (B111-5-L) by Kukamet — horizontal base, safety lock The Horizontal toggle clamp 111 (B111-5-L) is a robust lever clamp designed for repetitive workholding at a 90° angle, suited to jigs, fixtures and assembly stations in industrial and workshop environments. Safety lock for secure holding Horizontal base for stable mounting Holding force up to 5,000 N Pressure spindle M12×80 Reliable high-force clamping for repeatable processes The lever mechanism delivers a consistent 4,500 N clamping force with a maximum 5,000 N holding force, providing dependable retention for machining and assembly operations. The integrated M12×80 pressure spindle enables fine adjustment of contact pressure, so clamping can be adapted to different workpiece geometries without changing the fixture. These measurable values translate into fewer repositionings, reduced process variation and improved throughput in batch production. Safe, durable build for everyday workshop use Constructed with a blackened finish for corrosion resistance and a compact mass of 1.52 kg, the unit combines wear resistance with easy handling during installation. The built-in safety lock prevents accidental release under load, improving operator safety and protecting fixtures during vibration-prone processes. The horizontal base design allows secure attachment to plates or machine beds, offering a stable mounting solution that minimises setup time and preserves alignment across repeated cycles. Versatile integration that speeds up assembly and jigs As a classic lever clamp, this model is straightforward to incorporate into bespoke fixtures or standard clamping racks, delivering consistent clamping action without complex controls. The 90° operating angle provides clear actuation space and predictable kinematics, which supports faster cycle times and simplifies process planning. Transparent technical values and rugged construction make this clamp a practical choice where reliable, manual workholding must be combined with repeatability and safety. Contact Metav Werkzeuge for tailored technical advice and a quotation for the Kukamet Horizontal toggle clamp 111 (B111-5-L), available from our Emmerich warehouse Technical data SKU: B111-5-L GTIN: 8680731507102 Model: 111 Brand: Kukamet ECLASS: 21041719 ETIM: EC011973 Performance data Clamping force max: 4,500 N Holding force max: 5,000 N Pressure spindle: M12×80 Angle: 90° Weight: 1.52 kg Design & features Horizontal mounting foot Safety lock Blackened finish Lever clamp type FAQ What maximum holding and clamping forces does this clamp provide? The Kukamet Horizontal toggle clamp 111 (B111-5-L) offers a maximum clamping force of 4,500 N and a holding force up to 5,000 N. How is the clamp mounted to a fixture or machine table? Mounting is via the horizontal base; the horizontal mounting foot on the 111 (B111-5-L) allows secure attachment to plates or beds used in jigs and fixtures. Is there an adjustable contact point on the clamp? Yes, the clamp uses an M12×80 pressure spindle for adjustment of the contact pressure and to accommodate varying workpiece heights. Does the clamp include any feature to prevent accidental release? The unit is fitted with a safety lock to maintain engagement under load and to reduce the risk of unintentional opening during operation. What finish and durability can be expected from this model? The clamp is supplied with a blackened finish, providing corrosion resistance and a robust surface suitable for daily workshop use. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 58mm Horizontal Clamp With Massive Holding Arm And Safety Lock, 2500N Holding Force - Kukamet
Robust 58 mm arm combined with a massive holding arm and a secure safety latch ensures consistent clamping performance up to 2.3 kN; the angled base enables fixed 90° mounting for repeatable jig setups. Order the clamp through Metav Werkzeuge or consult our advisers for application-specific recommendations. Horizontal toggle clamp 113 — Kukamet horizontal clamp with 58 mm arm and 2.3 kN clamping force The Horizontal toggle clamp 113 is a compact, 90° horizontal workholding clamp with an angled foot for stable mounting in fixtures and jigs. Massive holding arm and safety latch 58 mm arm for compact clamping reach 2.3 kN clamping force, 2.5 kN holding force Angled base for 90° horizontal mounting Reliable clamping performance for production use The toggle clamp delivers a defined clamping force of up to 2,300 N, supported by a maximum holding force of 2,500 N, offering predictable behaviour in repetitive operations. Such reproducible force levels reduce set-up variance and contribute to shorter cycle times when used in fixtures or assembly jigs. The concise arm length of 58 mm provides a compact reach that fits tight toolroom spaces while maintaining effective leverage. These measurable values allow planners to calculate clamp placement and fixture stability in advance, improving process planning and operational efficiency. Durable design that stands up to daily workshop demands Constructed with a massive holding arm and finished in a black oxide finish, the clamp resists wear and handling in busy environments. The integrated safety latch secures the lever in the closed position, preventing accidental release and enhancing operator safety in semi-automated and manual workflows. At approximately 0.42 kg, the unit combines low mass with structural robustness, enabling easy integration into portable jigs without compromising strength. Material choices and mechanical locking ensure long service life and minimal maintenance, supporting continuous production without unexpected downtime. Simple mounting and fast operation for versatile fixtures The clamp features an angled foot mounting design set at 90°, allowing direct attachment to plates and fixture boards for horizontal workholding. This geometry simplifies alignment when clamping flat or profiled parts and reduces the need for additional brackets. The toggle mechanism offers quick actuation for rapid part loading and unloading, improving throughput in batch tasks. Its compact footprint and standard mounting arrangement make the component suitable for a wide range of applications, from inspection stations to light-duty press or assembly fixtures, while maintaining consistent clamping behaviour across cycles. Contact Metav Werkzeuge for tailored fixture advice or to secure the Kukamet Horizontal toggle clamp 113 (SKU B113-3-D-L-C1) for your production line; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: B113-3-D-L-C1 SKU: B113-3-D-L-C1 ECLASS: 21041719 ETIM: EC011973 Facts Clamping force (max): 2,300 N Holding force (max): 2,500 N Arm length: 58 mm Weight: 0.42 kg Angle: 90° Special features Angled foot (Winkelfuß) mounting Massive holding arm Safety latch (Sicherheitsverriegelung) Black oxide finish (Schwarz brüniert) Model designation: 113 Category: Spanner FAQ What maximum clamping force does the clamp provide? The Kukamet Horizontal toggle clamp 113 provides a maximum clamping force of 2,300 N with a holding force rated up to 2,500 N. Is the clamp suitable for fixture mounting at 90°? Yes. The clamp is designed with an angled foot for direct 90° horizontal mounting, making it suitable for plates and fixture boards in jigs. What is the arm length and how does it affect reach? The unit has a 58 mm arm length, offering a compact reach that is ideal for confined fixture spaces while maintaining effective leverage. Does the clamp include any safety features to prevent accidental release? The clamp is equipped with a safety latch that secures the lever in the closed position to reduce the risk of unintended opening. Which finish and materials contribute to durability? The clamp is supplied with a black oxide finish, and a massive holding arm construction designed to withstand regular workshop use. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 58mm Horizontal Clamp With Massive Holding Arm, 2.5kN Hold Force, Zinc Plated - Kukamet
Benefit from a combination of high holding performance and durable construction: a 58 mm solid holding arm, zinc-plated corrosion protection and a rated holding force of 2,500 N provide reliable, repeatable clamping for production and assembly tasks. Order the clamp directly via Metav Werkzeuge or contact our consultants for application advice. Kukamet Horizontal toggle clamp 113 — 58 mm arm, zinc-plated The Horizontal toggle clamp 113 is a 90° horizontal clamp with an angled foot mount, designed for secure workpiece fixation in workshop and assembly environments Massive 58 mm holding arm Zinc-plated corrosion protection Clamping force up to 2,500 N 90° angle foot mounting Reliable holding power for repeatable processes The clamp delivers a measurable holding capacity, with a holding force of 2,500 N and a pressing force of 2,300 N, providing the mechanical certainty required for repeatable clamping operations. These numerical values translate into stable fixation during machining, welding or assembly, reducing re-clamping and cycle interruptions. The compact, 58 mm arm ensures short lever travel and consistent contact pressure, which supports process consistency on production lines and in small-batch workshops. Built to endure workshop conditions Constructed with a zinc-plated finish and a solid holding arm, the device resists corrosion and mechanical wear typical of industrial environments. The combination of robust materials and a lightweight design (approx. 0.37 kg) keeps handling and integration straightforward while extending service life under frequent use. The corrosion-resistant coating reduces maintenance intervals and preserves appearance and function where exposure to humidity or coolant splash is present, supporting lower total cost of ownership over time. Fast integration and versatile mounting The 90° angle foot mounting simplifies installation on jigs, fixtures and machine tables, allowing the clamp to be positioned close to the workpiece for efficient space utilisation. The compact base profile and standardised fixing pattern make retrofitting into existing tooling straightforward, while the clamp’s solid construction ensures secure engagement even in repetitive production cycles. For advice on specific mounting configurations or to confirm compatibility with a particular fixture, technical guidance is available. Contact Metav Werkzeuge for technical guidance on integrating the Kukamet horizontal toggle clamp 113 into production setups — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: 113-3-D-C1 GTIN: 8680731500837 Brand: Kukamet Core data Arm length: 58 mm Angle: 90° Holding force: 2,500 N Pressing force: 2,300 N Weight: 0.37 kg Material: zinc-plated Special features Mounting type: angle foot Solid holding arm Category: clamp (Spanner) eClass: 21041719 ETIM: EC011973 FAQ What holding capacity does the clamp offer? The Kukamet horizontal toggle clamp 113 provides a holding force of 2,500 N and a pressing force of 2,300 N (SKU 113-3-D-C1), suitable for many light to medium production tasks. Is the clamp suitable for humid or coolant-prone environments? The clamp’s zinc-plated finish offers corrosion resistance, making the Kukamet horizontal toggle clamp 113 appropriate where occasional moisture or coolant exposure occurs. How is the clamp mounted to a fixture? Mounting is via a 90° angle foot; the compact base allows secure attachment to jigs, fixtures and machine tables for close workpiece access. Can the clamp be used in automated fixtures? The clamp’s compact design and solid holding arm support integration into fixtures and assembly lines; consult Metav Werkzeuge for compatibility details with specific automation setups. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 58mm Horizontal Clamp With Massive Holding Arm, Safety Lock, 2.5 kN Hold Force, Zinc Plated - Kukamet
Combine robust safety locking and a zinc‑plated 58 mm arm with reliable clamping performance up to 2,300 N to secure fixtures in repetitive production tasks—order the clamp directly via Metav Werkzeuge or consult our technical advisors for application support. Horizontal toggle clamp 113 — Kukamet horizontal clamp with angled foot and zinc finish The Horizontal toggle clamp 113 is a right‑angle mounting clamp designed for workshop jigs and industrial fixturing, offering a compact profile with a reinforced holding arm and a safety locking mechanism. Massive holding arm with safety lock Angled foot for secure right‑angle mounting Clamping force up to 2,300 N Zinc‑plated finish for corrosion resistance Reliable high‑force holding for repeated operations The clamp delivers a defined clamping force of up to 2,300 N and a holding force of 2,500 N, features that translate into secure, vibration‑resistant workholding in series production. The reinforced arm and toggle mechanism reduce play under load, which improves positional accuracy on jigs and fixtures. For users replacing makeshift clamps with a robust solution, the mechanical design provides predictable performance and repeatability in every cycle. Easy integration into right‑angle jigs and assemblies Engineered for right‑angle mounting via an angled foot, the device mounts cleanly to plates and fixture bases at a 90° orientation, saving setup time and aligning with standard jig geometry. The compact 58 mm arm length balances reach and clearance, making the clamp suitable where space is limited yet a firm hold is required. At just 0.42 kg, the assemble‑friendly weight simplifies handling during fixture build‑up and reduces load on moving sub‑assemblies. Corrosion protection, safety and application range A zinc‑plated surface provides corrosion resistance suitable for workshop environments, extending service life where moisture or splash is present. The massive holding arm combined with a positive safety lock prevents accidental release under vibration, supporting secure clamping in automation and manual production lines. Typical applications include fixture clamping, welding jigs, assembly benches and repetitive machining operations where a robust, right‑angle clamp improves throughput and operator confidence. Choose the Kukamet 113 horizontal clamp for dependable high‑force fixture holding—contact Metav Werkzeuge for tailored application advice and reliable supply from Emmerich Technical data Article number: 113-3-D-L-C1 GTIN: 8680731500868 ECLASS: 21041719 ETIM: EC011973 Core specifications Arm length: 58 mm Clamping force: 2,300 N Holding force: 2,500 N Angle: 90° Weight: 0.42 kg Materials and special features Material: zinc‑plated Mounting: angled foot Massive holding arm Safety locking mechanism Category: clamp FAQ What maximum clamping and holding forces does the clamp provide? The Kukamet Horizontal toggle clamp 113 offers a clamping force of up to 2,300 N and a holding force of 2,500 N for secure fixture retention. Which mounting method is required for installation? Mounting is via an angled foot at a 90° orientation, intended for secure right‑angle attachment to fixture plates and bases. Is the clamp suitable for corrosive or humid workshop environments? The zinc‑plated finish on the Horizontal toggle clamp 113 provides corrosion resistance appropriate for typical workshop conditions. What are typical use cases for this clamp? Common applications are welding jigs, assembly benches, machining fixtures and repetitive production tasks where a compact, reliable right‑angle clamp is needed. How compact is the clamp for tight fixtures? With a 58 mm arm and a lightweight 0.42 kg construction, the clamp fits into confined setups while maintaining substantial clamping performance. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 60mm Horizontal Clamp With Massive Holding Arm, Safety Lock, 1,200N Holding Force - Kukamet
The robust construction with a massive holding arm and integrated safety lock ensures consistent part retention and safe operation under repeated cycles. With a compact 60 mm lever and an angled base for stable mounting, this clamp delivers up to 1,200 N holding force and 1,000 N operating force for dependable fixture performance. Order the Horizontal clamp 113 directly via Metav Werkzeuge or ask our consultants if needed. Horizontal clamp 113 — Kukamet horizontal toggle clamp with 60 mm arm and safety lock The Horizontal clamp 113 is a compact horizontal toggle clamp designed for secure workpiece fixation in fixtures, jigs and assembly stations where space and repeatable clamping force are essential. Massive holding arm with safety lock 60 mm lever arm for compact fixtures Holding force up to 1,200 N Angled base (90°) for secure mounting Reliable clamping force for consistent production results The 113 delivers a measurable holding force of 1,200 N and a maximum operating force of 1,000 N, providing predictable clamping performance for medium-duty applications. These values indicate the clamp’s ability to resist displacement under lateral and withdrawal loads, which is particularly relevant for repeatable assembly and light machining tasks. Specified forces allow engineers to calculate safety margins and cycle reliability when designing fixtures and jigs, reducing scrap rates and improving overall process stability. Compact mounting and durable finish for workshop environments Equipped with a 60 mm lever arm and an angled base (90°), the clamp integrates into confined fixture layouts without compromising accessibility. The blackened finish offers surface protection against corrosion while maintaining a low-reflective appearance for inspection and optical setups. The component’s low mass (approx. 0.27 kg) makes it suitable for portable fixtures and modular clamping plates, and the compact footprint supports higher density of clamping points where space is limited. Safety features and long-term operational benefits A massive holding arm combined with a dedicated safety lock reduces accidental release during handling or vibration-heavy processes, enhancing operator safety and protecting delicate workpieces. The mechanical toggle principle ensures repeatable closure with minimal adjustment, which shortens fixture setup times and contributes to faster cycle throughput. As part of a workshop’s clamping strategy, this clamp supports robust, low-maintenance operation and helps maintain consistent quality across production runs. For reliable fixture clamping and specification advice, contact Metav Werkzeuge to discuss the Kukamet 113 or request a tailored quotation by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: B113-2-D-L-C1 Manufacturer: Kukamet Arm length: 60 mm Holding force: 1,200 N Maximum operating force: 1,000 N Angle: 90° Weight: 0.27 kg ECLASS: 21041719 ETIM: EC011973 Mounting: Angled base (Winkelfuß) Finish: Blackened finish Feature: Massive holding arm Feature: Safety lock Category: Clamping elements (toggle clamp) FAQ What is the difference between holding force and operating force? Holding force refers to the maximum retention capacity under static load, while operating force is the input force required to engage the clamp; the Horizontal clamp 113 specifies 1,200 N holding force and 1,000 N operating force. Can the clamp be mounted on angled plates or at 90° positions? Yes, the 113 features an angled base (90°) designed for secure mounting on angled plates and fixture blocks. Is the safety lock suitable for vibration-prone environments? The integrated safety lock prevents accidental opening and is intended to improve retention during vibration and frequent cycle conditions with the Kukamet horizontal clamp. Which materials and applications suit this clamp best? The clamp’s robust lever and finish make it suitable for general workshop applications such as assembly, light machining and jigs requiring reliable repeatable clamping. What are the physical dimensions relevant for fixture design? Key dimensions for integration are the 60 mm lever arm, the 90° base angle and the unit weight of approx. 0.27 kg, which support compact and portable fixture designs. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 60mm Horizontal Clamp With Solid Holding Arm, 1,000 N Thrust / 1,200 N Hold - Kukamet
Compact galvanised construction and a 60 mm massive holding arm deliver dependable clamping with low maintenance and long service life, while the 1,200 N maximum holding force and 1,000 N clamping force ensure secure workpiece fixation. Order the clamp directly via Metav Werkzeuge or contact our consultants for specification support. Horizontal toggle clamp 113 — galvanised horizontal clamp with 60 mm arm The Horizontal toggle clamp 113 is a horizontal toggle clamp designed for secure, repeatable workholding in production, assembly and jig applications, providing a compact solution for fixtures that require a firm 90° mounting orientation. Robust galvanised finish 60 mm massive holding arm 1,200 N maximum holding force 90° angle foot mounting Consistent, measurable clamping performance for production use The clamp delivers 1,000 N nominal clamping force and 1,200 N maximum holding capacity, values that translate into improved process stability and fewer rejects in repetitive operations. The distinction between clamping and holding force reflects the dynamic pressure applied during locking and the static resistance to displacement once the toggle is engaged; this combination supports both short-cycle clamping and longer-term fixturing. Documented force values aid planning and risk assessment in fixture design. Galvanised finish and a rigid arm for harsh workshop environments A galvanised surface finish provides enhanced corrosion protection compared with raw steel, reducing downtime for maintenance and extending service intervals. The 60 mm massive holding arm reduces bending and wear at the contact zone, increasing repeatability over many cycles. The clamp’s 90° angle foot mount allows straightforward integration into plates and jig bases, simplifying layout and ensuring a rigid connection between fixture and workbench. Fast toggle action and lightweight installation for efficient workflows The toggle mechanism offers rapid engagement and release, cutting changeover times in assembly and inspection processes; the device is optimised for quick manual operation while delivering reliable locking. The clamp’s compact construction and 0.215 kg weight make it suitable for modular fixtures and relocatable jigs, where minimising added mass is beneficial for handling and machine loading. The toggle design also reduces the need for frequent readjustment, supporting consistent cycle times. Secure supply and specification support are available from Metav Werkzeuge — for product ordering or application advice contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 113-2-D-C1 GTIN: 8680731500752 Manufacturer: Kukamet Material: galvanised steel Mounting: angle foot SKU: 113-2-D-C1 Facts Arm length: 60 mm Weight: 0.215 kg Max clamping force: 1,000 N Max holding force: 1,200 N Mounting angle: 90° Special features Massive holding arm Galvanised finish Angle foot mounting Toggle clamp design Compact, lightweight construction FAQ Is the clamp suitable for production jigs and fixtures? Yes. The Horizontal toggle clamp 113 is designed for production jigs and fixtures, providing standardised forces (1,000 N clamping, 1,200 N holding) that support repeatable workholding. What is the mounting arrangement for the clamp? The clamp uses a 90° angle foot mount for secure attachment to plates and jig bases, simplifying integration into existing fixture layouts. Which materials are used for the clamp’s construction? The clamp is made from galvanised steel, offering improved corrosion resistance for workshop environments and reduced maintenance compared with untreated steel. How does the toggle mechanism affect cycle times? The toggle action enables fast engagement and release, reducing changeover time in assembly and inspection tasks and increasing overall process throughput. Can the clamp be used in modular, lightweight fixtures? Yes. With a weight of 0.215 kg and a compact footprint, the clamp is suitable for modular fixtures where low added mass and easy repositioning are required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 62mm Pneumatic Clamp Vertical Base, 1,200 N Push / 1,400 N Hold, Galvanised Massif Arm - Kukamet
Robust, galvanised construction combined with a 62 mm reach and reliable pneumatic actuation delivers consistent clamping performance — ideal for fixture builders who demand repeatability. Order the Kukamet 651 through Metav Werkzeuge or consult our specialists for integration advice. Pneumatic clamp 651 — vertical-base, 62 mm arm, Kukamet The Pneumatic clamp 651 is a 90° pneumatic clamping unit with a vertical base and a massive holding arm, designed for repeatable fixturing and industrial assembly applications Massive holding arm for high rigidity 62 mm reach arm for compact fixturing Vertical base mounting for bench or plate fixing Galvanised finish for corrosion resistance Consistent clamping and holding for fewer rejects Pneumatic actuation provides repeatable, measurable force that reduces variability across production runs. The unit delivers a 1,200 N actuation force and a 1,400 N holding capacity, which separates the initial clamping action from the static resistance once the part is secured. This distinction means reliable immobilisation during machining or assembly, lowering rework rates and improving throughput. The predictable performance of pneumatic actuation also simplifies cycle-time planning on automated lines. Rigid, compact design that improves process accuracy A massive holding arm combined with a 62 mm arm length and a fixed 90° orientation gives a high stiffness-to-size ratio. The vertical base mounting ensures stable anchoring to benches or fixture plates, reducing deflection under load and maintaining alignment during operations. The galvanised finish protects the mechanism in workshop environments while the compact footprint supports dense fixture layouts, freeing up space without sacrificing stability. Faster cycles with safer, low-effort operation Pneumatic operation allows rapid actuation and consistent closing speed, contributing to consistent cycle times and reduced operator fatigue compared with manual levers. The clamping motion is powered by compressed air and controlled via valves, which enables simple integration with existing pneumatic systems or PLC controls. The result is a clamping unit that accelerates repetitive tasks while maintaining a high safety margin through controlled motion and fixed geometry. Practical fit for workshops and production lines The clamping unit suits assembly jigs, welding fixtures and light machining setups where fixed-angle, repeatable clamping is required. Its combination of vertical base mounting and compact reach makes it particularly useful in modular fixtures and confined spaces. For procurement, Metav combines broad availability with a quality filter based in Emmerich, offering a straightforward supply chain for standardised fixturing components and specialist advice when planning installations. Contact Metav Werkzeuge to discuss how Kukamet's 651 pneumatic clamp with 1,200 N actuation and 1,400 N holding force can be specified for current fixtures and production needs Technical data SKU: 651-2-D-C1 Model: 651 Type: Pneumatic clamp Mounting: Vertical base Arm reach: 62 mm Angle: 90° Actuation force (max): 1,200 N Holding force (max): 1,400 N Material: Galvanised Special feature: Massive holding arm eClass: 21021004 ETIM: EC011973 Performance figures Arm: 62 mm Max actuation force: 1,200 N Max holding force: 1,400 N Angle: 90° SKU: 651-2-D-C1 Features and materials Galvanised finish Massive holding arm Vertical base mounting Pneumatic actuation Lever-style clamping concept (hebelspanner) FAQ What clamping and holding forces does the unit provide? The Kukamet 651 provides a maximum actuation force of 1,200 N and a holding capacity of 1,400 N, as stated in the technical data for reliable immobilisation during operations. Can the clamp be mounted on a fixture plate or bench? Yes. The vertical base mounting is designed for secure fixing to benches or fixture plates, enabling stable installation in modular fixturing systems. Is the arm suitable for tight or compact fixture layouts? The 62 mm arm reach and compact design make the clamp appropriate for confined fixturing arrangements while maintaining stiffness and alignment. How does pneumatic actuation benefit production environments? Pneumatic actuation on the Kukamet 651 offers fast, repeatable motion and predictable cycle times, supporting automation and reducing manual effort in repetitive tasks. Does the finish protect the clamp in workshop settings? The galvanised material provides corrosion resistance suitable for standard workshop environments, helping to extend service life and maintain consistent performance. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 62mm Pneumatic Clamp With Vertical Handle And Solid Holding Arm, 1,200N Thrust / 1,400N Hold - Kukamet
Take advantage of a robust, pneumatically driven clamping solution combining consistent 1,200 N operating force, a massive galvanised holding arm, and compact mounting for space-efficient fixtures; order the unit directly via Metav Werkzeuge or consult our specialists for integration advice. 651 Pneumatic clamp — vertical-handle design with 1,200 N clamping force (Kukamet) The 651 is a pneumatic clamp for secure fixture clamping in production jigs and workshop assemblies Vertical handle with robust holding arm 1,200 N operating force for repeatable clamping 1,400 N holding force for secure locking Galvanised construction for corrosion resistance Consistent clamping force for reliable production The pneumatically actuated design delivers a consistent 1,200 N operating force that keeps parts fixed during machining and assembly, reducing variability between cycles. Built-in pneumatic actuation ensures uniform strokes and predictable pressure across repeated operations, which shortens setup time and lowers scrap rates. The unit also provides a 1,400 N holding force, offering a safety margin for transient loads; both values enable clear planning of fixture capacity and allow engineers to match the clamp to process force requirements. Compact mounting and ergonomic handling to speed workflows Designed with a vertical-foot mounting and a vertical handle, the clamp fits neatly into tight fixture layouts while remaining easy to operate during manual loading or automated cycling. The 62 mm arm gives a practical reach for many workpiece geometries without adding bulk, and the 90° orientation suits typical right-angle fixture arrangements. The combination of compact installation and an intuitive handle contributes to faster part changes and smoother cycle integration on both manual benches and automated stations. Robust construction that reduces maintenance and downtime A galvanised finish and a massive holding arm deliver resistance to corrosion and mechanical wear, which extends service intervals and supports continuous operation in demanding workshop environments. Heavy-duty components limit deformation under load, maintaining clamping accuracy over long production runs. The simple mechanical principle behind the clamp also makes servicing straightforward: fewer moving parts mean less to maintain, so assembly lines and fixtures stay productive with predictable upkeep. For specification guidance, mounting options or fast supply of the Kukamet 651 pneumatic clamp, contact Metav Werkzeuge in Emmerich—email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance and technical advice Technical data Article number: 651-2-H-D-C1 Product: Pneumatic clamp 651 Manufacturer: Kukamet Performance data Max operating force: 1,200 N Max holding force: 1,400 N Arm: 62 mm Angle: 90° eCl@ss: 21021004 ETIM: EC011973 Construction & features Galvanised finish Vertical handle Massive holding arm Vertical-foot mounting Catalogue: 611-612-631-651-652-katalogseite.pdf FAQ What clamping and holding forces does the clamp provide? The Kukamet 651 pneumatic clamp provides a maximum operating force of 1,200 N and a holding force of 1,400 N, suitable for secure part fixation in many production and fixture applications. Can the clamp be mounted in a vertical orientation? Yes, the clamp features a vertical-foot mounting and a vertical handle, making the 651 suitable for right-angle fixtures and space-limited mounting configurations. How does the construction influence service life? The galvanised finish and massive holding arm of the 651 reduce corrosion and mechanical wear, extending service intervals and supporting long-term, repetitive use on workshop and production lines. Is the 62 mm arm suitable for varied workpiece geometries? The 62 mm arm provides a practical reach for a wide range of small to medium workpieces and is designed to balance reach with compact fixture integration. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 6500 N Pneumatic Clamp With Pneumatic Cylinder, Zinc Plated, 30000 N Holding Force - Kukamet
Take advantage of the combination of robust galvanised construction, high holding force 30,000 N and repeatable pneumatic actuation for reliable fixture performance; this clamp supports stable production cycles and reduces rework. Order the (Kukamet Pneumatic toggle clamp 682) directly via (Metav Werkzeuge) or ask our consultants if needed. Pneumatic toggle clamp 682 by Kukamet — Pneumatic cylinder, 30,000 N holding force A pneumatic toggle clamp 682 engineered for secure horizontal mounting in jigs, fixtures and production tooling where consistent clamping and high holding performance are required. Galvanised construction for corrosion resistance Holding force 30,000 N Pneumatic cylinder actuation Horizontal base for stable mounting Consistent, measurable clamping for repeatable processes The pneumatic actuation and toggle mechanism deliver a consistent clamping force that supports repeatable cycle times and predictable process results. With a max press force of 6,500 N generated by the pneumatic cylinder and a holding force of 30,000 N once the clamp is engaged, the unit separates actuation force from static retention, reducing slip and part movement during machining or welding. This separation of functions translates into fewer rejects and shorter setup checks, a tangible efficiency argument for production lines and fixture designers. Durable construction that minimises maintenance and downtime Constructed from galvanised components and fitted with a horizontal mounting foot, the clamp provides mechanical robustness and enhanced corrosion resistance suitable for workshop environments. The substantial mass (21.269 kg) contributes to stability under dynamic loads and helps maintain alignment over repeated cycles. The galvanised finish reduces surface corrosion, extending service life and lowering lifetime maintenance effort. Simple mechanical geometry of the toggle means inspections focus on seals and pneumatic fittings rather than complex transmission elements. Integration-friendly design for industrial fixtures and automated cells The 90° toggle geometry and horizontal base facilitate straightforward integration into jigs, presses and automated assemblies, providing a compact clamping solution with a defined clamping direction. The combination of pneumatic cylinder actuation and toggle linkage enables fast actuation speeds and controlled closing behaviour, suitable for pick-and-place sequences or welding fixtures where cycle speed and safety interlocks are critical. Adjustment options in the clamping interface permit alignment with existing datum points, supporting installation in both manual and robotic workstations while maintaining repeatability across production batches. For a technical consultation or a tailored quotation for the Kukamet 682 pneumatic toggle clamp, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: 682-8 GTIN: 8680731505153 Manufacturer: Kukamet Eclass: 21021004 ETIM: EC011973 Facts Weight: 21.269 kg Max holding force: 30,000 N Max press force: 6,500 N Angle: 90° Special features Material: Galvanised Mounting: Horizontal base Actuation: Pneumatic cylinder FAQ What is the difference between pressing force and holding force on this clamp? The pneumatic cylinder of the Kukamet 682 generates the pressing force of 6,500 N used to engage the toggle; the holding force of 30,000 N is the static retention capacity provided by the toggle mechanism once clamped. For which applications is this clamp most suitable? The clamp is intended for fixtures, jigs, welding and assembly operations where a defined clamping direction, fast pneumatic actuation and high retention are required; the horizontal base simplifies mounting in production tooling. How is the clamp mounted and aligned in a fixture? Mounting is via the horizontal base; alignment is achieved by positioning the base on the datum surface and securing with appropriate fasteners. The 90° toggle geometry provides a clear clamping direction for fixture design. What routine maintenance is required? Maintenance focuses on pneumatic fittings, seal condition and the toggle pivot points; periodic inspection and replacement of seals or pneumatic hoses preserves performance and repeatability. Is the galvanised finish suitable for humid or mildly corrosive environments? The galvanised surface improves corrosion resistance for workshop conditions; for continuous outdoor exposure or aggressive chemical environments, supplementary protection or specific material selection should be considered. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 6500 N Pneumatic Clamp Without Cylinder, Zinc-Plated, 30 kN Holding Force - Kukamet
Take advantage of the combination of robust holding force, galvanised durability and a compact horizontal-foot design to secure high-repeatability workholding in production. The clamp’s compatibility with customer-specified pneumatic cylinders and its lever-style 90° configuration make it a flexible choice for fixture systems; order via Metav Werkzeuge or consult our specialists for integration advice. Pneumatic clamp 681 – Horizontal-foot 90° lever clamp (Kukamet) The Pneumatic clamp 681 is a horizontal-foot, lever-style clamp designed for secure, repeatable workholding in industrial fixture applications and supplied without a pneumatic cylinder Galvanised steel construction Max holding force 30,000 N Actuating force up to 6,500 N Horizontal foot mounting 90° lever clamp configuration Secure clamping that improves process reliability The lever-style clamping mechanism delivers a clear distinction between actuating force and holding force, with an actuating peak of 6,500 N and a steady holding capacity of 30,000 N. This separation ensures that short control pulses from valve systems achieve fast closure while the high retention force maintains parts reliably during machining or assembly, reducing rework and scrap. The galvanised finish contributes corrosion resistance and long-term dimensional stability in workshop environments. Compact mounting for flexible fixture integration Designed with a horizontal foot and a 90° lever angle, this clamp suits fixture plates and custom jigs where lateral clearance and predictable clamp geometry are essential. The unit’s mass (approx. 11.3 kg) provides inherent stability without excessive bulk, allowing straightforward bolting to tooling plates. The compact footprint supports tight nest arrangements and faster changeovers, which is beneficial for medium- to high-volume production runs demanding short cycle times. Adaptable supply concept and low-maintenance operation Delivered without pneumatic cylinder, the clamp allows selection of a cylinder to match system pressure and control schemes, enabling tailored actuation speeds and integration with existing pneumatics. The galvanised material minimises surface wear and eases maintenance cycles, while the lever configuration offers simple mechanical inspection points. Supplied by Kukamet and distributed through Metav Werkzeuge’s quality-filtered supply chain, the device is intended for reliable workshop use across a range of production environments. Contact Metav Werkzeuge today to discuss integrating the Kukamet Pneumatic clamp 681 into existing fixtures or to request application-specific advice from our specialists Technical data Article number: 681-8-M GTIN: 8680731506624 Brand: Kukamet Core specifications Weight: 11.3 kg Max holding force: 30,000 N Max actuating force (closing): 6,500 N Angle: 90° eClass: 21021004 ETIM: EC011973 Features & materials Material: galvanised steel Mounting: horizontal foot Supplied without pneumatic cylinder Lever-style clamp (hebelspanner) Category: clamp FAQ What is the difference between actuating and holding force for this clamp? The actuating force is the force required to drive the clamp into the closed position (6,500 N), while the holding force (30,000 N) is the retention capacity once the clamp is engaged; the Pneumatic clamp 681 separates these functions for efficient control and strong retention. Is a pneumatic cylinder included with the clamp? No, the clamp is supplied without a pneumatic cylinder so that an appropriate cylinder can be selected to match system pressure and cycle requirements when integrating the Kukamet clamp 681. How is the clamp mounted to a fixture plate? The clamp uses a horizontal foot mounting that is bolted to tooling plates or fixture bases; the horizontal-foot design and 90° lever geometry facilitate predictable clamping positions for jigs and fixtures. Can the clamp be used in corrosive or humid workshop environments? The galvanised steel construction provides enhanced corrosion resistance compared with untreated components, supporting longer service life in standard workshop conditions for the Kukamet Pneumatic clamp 681. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 650mm Pneumatic Clamp Vertical Handle Massive Arm, 4 500 N Pressure / 5 000 N Holding Force, Zinc Plated - Kukamet
Robust galvanised construction combined with a 5,000 N holding capacity and a 130 mm holding arm delivers reliable, repeatable fixturing for industrial production. Order the clamp directly via Metav Werkzeuge or consult our advisors for application support. Pneumatic clamp 651 – Vertical-handle pneumatic clamp with massive holding arm (Kukamet) A Pneumatic clamp 651 designed for secure, repeatable workholding in industrial jigs and fixtures with a vertical handle and galvanised, heavy-duty arm Vertical handle for compact actuation Massive galvanised holding arm for durability Holding force up to 5,000 N for secure fixturing Pressure force rating 4,500 N for pneumatic drive 130 mm arm length with 90° operating angle Stable, measurable clamping for efficient production The clamp delivers a quantifiable improvement in workholding: holding force 5,000 N and a pressure force of 4,500 N ensure components remain stationary through machining or assembly. This measurable performance reduces rework and inspection time by improving process stability. The vertical-actuation layout provides predictable force transfer into the fixture, supporting repeatable clamping cycles and consistent quality control across batches. Durable design reduces downtime and maintenance Constructed with a galvanised finish and a massive holding arm, the unit resists corrosion and mechanical wear in workshop environments. The vertical foot mounting secures the clamp rigidly to fixture plates, while the robust arm geometry distributes load away from the fastenings. As a consequence, equipment service intervals are lengthened and fixture downtime is reduced, supporting continuous production and lower total cost of ownership. Compact integration that speeds up setup and cycle time With a 130 mm arm and a fixed 90° operating angle, the clamp is engineered for compact integration into jigs and automated cells. The vertical handle orientation saves lateral space on tooling plates and enables simple pneumatic line routing. Pneumatic actuation provides rapid, controllable motion suitable for short cycle times, aiding throughput and process automation without extensive mechanical complexity. Suitable use cases and operational guidance The device is aimed at heavy-duty fixturing tasks in industrial workshops, assembly lines and machining fixtures where stable, repeatable holding is required. The galvanised construction and solid arm make it particularly appropriate where robustness and corrosion resistance are expected. Basic preventive checks—visual inspection of mounting points and air connections—help preserve long-term reliability and consistent clamping performance. For secure, high-force clamping from Kukamet, contact Metav Werkzeuge in Emmerich for tailored advice and ordering: info@metav-werkzeuge.com • +49 2822 7131930 Technical data SKU: 651-5-H-D-C1 Model: 651 Type: Pneumatic clamp Brand: Kukamet Core specifications Arm length: 130 mm Holding force max: 5,000 N Pressure force max: 4,500 N Angle: 90° eCl@ss: 21021004 ETIM: EC011973 Special features Mounting: vertical foot Handle: vertical handle Holding arm: massive, galvanised Material: galvanised steel Image asset: 651-H-D-main.jpg FAQ What is the maximum holding force of this clamp? The clamp provides a maximum holding force of 5,000 N as specified for the Pneumatic clamp 651 (SKU 651-5-H-D-C1). Is the clamp designed for vertical mounting? Yes, the unit features a vertical foot for mounting and a vertical handle for compact actuation in fixtures. What material is used for the clamp's arm and body? The main components are finished in galvanised steel; the holding arm is delivered as a massive, durable element. Which angle does the clamp operate at? The mechanism is set to operate at a 90° angle, suitable for many standard fixture geometries. Is the clamp suitable for automated production lines? The pneumatic actuation and compact footprint make this clamp suitable for automated jigs and short-cycle production environments. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 652 Pneumatic Clamp With Vertical Base, 2,000 N Stroke Force, Zinc Plated — Kukamet
Combine a massive 67 mm clamping arm with up to 2,500 N holding force and a galvanised finish for dependable, low-maintenance fixture control; order the pneumatic clamp directly via Metav Werkzeuge or consult our advisors for specification support. Pneumatic Clamp 652 by Kukamet — 67 mm arm, 2,500 N holding force The pneumatic clamp 652 is a vertical-foot lever clamp engineered for rapid, repeatable workpiece securing in production, assembly and fixture applications. Massive 67 mm clamping arm Galvanised corrosion protection Vertical-foot mounting for bench use Up to 2,500 N holding force 90° lever angle for compact clamping Consistent clamping force for stable production output The clamp delivers measurable performance: a holding force of 2,500 N and a pressing force of 2,000 N, providing reliable retention during machining, assembly or inspection operations. The pronounced 67 mm arm length and robust lever geometry reduce vibration and movement under load, which improves process stability and reduces rework. Specified forces are primary indicators for fixture design and allow planners to calculate safety margins and clamping layouts; the clear numeric values support rapid integration into existing jigs and fixtures. Easy integration and compact mounting for workshop efficiency Built for bench and fixture use, the device features vertical-foot mounting and a 90° lever angle, enabling compact installation and unobstructed access to the clamped area. The vertical-foot base simplifies attachment to plates or tooling blocks and keeps the clamp profile low, which is advantageous where space is limited. The galvanised finish contributes to long-term durability in busy workshop conditions, lowering maintenance intervals and enabling uninterrupted production runs. These design choices accelerate set-up times and contribute to smoother workflow. Durable construction with maintenance-focused design The clamp’s galvanised construction and massive clamping arm provide corrosion resistance and structural longevity in industrial environments. The lever-style actuation offers straightforward pneumatic operation compatible with standard shop air systems and control valves; the compact mechanism reduces points of wear and simplifies routine inspection. Supplied as a model with clear identification (SKU: 652-3-D-C1), the device is suitable where repeatable, high-load clamping is required and where robustness and low lifecycle maintenance are priorities. Kukamet’s design emphasis on solid materials supports high-utilisation settings. For tailored procurement or specification advice on the Kukamet pneumatic clamp 652, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical support and reliable supply. Technical data SKU: 652-3-D-C1 Manufacturer: Kukamet Model: 652 eClass: 21021004 ETIM: EC011973 Core measurements Arm length: 67 mm Max holding force: 2,500 N Max pressing force: 2,000 N Lever angle: 90° Materials & special features Material: galvanised Mounting: vertical-foot Massive clamping arm Lever-type pneumatic clamp Category: Spanner FAQ What maximum holding force does this clamp provide? The clamp offers a maximum holding force of 2,500 N as stated for the Kukamet pneumatic clamp 652 (SKU 652-3-D-C1). Can the clamp be mounted on a tooling plate or bench? Yes. The vertical-foot mounting of the 652 is intended for secure attachment to plates or benches and supports compact fixture layouts. What is the arm length and why does it matter? The device has a 67 mm clamping arm; arm length affects leverage, access to the workpiece and the distribution of clamping force within a fixture. Is the clamp suitable for harsh workshop environments? The galvanised finish and solid arm construction of the Kukamet unit are intended to resist corrosion and withstand continuous workshop use, reducing maintenance frequency. Which forces should be considered when designing a fixture with this clamp? Use the 2,000 N pressing force and 2,500 N holding force figures to calculate safety margins and to determine the number and placement of clamps in the fixture. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 652 Pneumatic Clamp With Vertical Base, 2 000 N Stroke Force, 2 500 N Holding Force, Galvanised - Kukamet
Take advantage of a robust combination of high holding force (2,500 N), reliable pneumatic actuation (2,000 N) and a zinc-plated finish that resists corrosion — delivering secure, repeatable clamping for production environments. Order directly via Metav Werkzeuge or consult the specialists for integration advice. 652 Pneumatic Clamp by Kukamet — vertical-foot mounting, zinc-plated, 2,500 N holding force 652 Pneumatic Clamp designed for secure, space-saving vertical installation in production jigs and assembly fixtures. Massive holding arm for stable clamping Zinc-plated corrosion-resistant finish Vertical-foot mounting with 90° clamping angle Holding force up to 2,500 N, pneumatic force 2,000 N Secure, high-force clamping for repeatable production The 652 pneumatic clamp offers a combination of holding force (2,500 N) and pneumatic actuation (2,000 N) that ensures components remain fixed during machining, welding and assembly. High clamping capacity reduces vibration and part movement, which in turn lowers scrap rates and rework. The result is a measurable improvement in process stability and component quality; operators benefit from predictable repeatability and reduced inspection workload. Technical planners will value the clear specification of force values when calculating fixture safety margins. Built for longevity and easy integration into fixtures Constructed with a zinc-plated surface and a massive holding arm, the clamp resists corrosion and maintains rigidity under cyclic loading, extending service intervals and preserving clamping accuracy. The unit is supplied for vertical-foot mounting, offering a compact footprint and a 90° clamping angle that suits many standard jig layouts. With an arm reach of 167 mm, the design balances accessibility and stiffness for a broad range of part sizes. These attributes simplify fixture design and help maintain clamping geometry during repeated cycles, supporting consistent machining tolerances. Practical benefits in the workshop and on the production line This pneumatic clamping solution fits into automated feed systems and manual fixtures alike; pneumatic actuation enables fast, controlled clamping cycles that reduce set-up time and lift throughput. The clamp requires minimal routine maintenance thanks to its robust construction and corrosion protection; scheduled inspections typically focus on pneumatic connections and wear points only. Engineers will find the device straightforward to specify for benches, jigs and small-batch production, while purchasing benefits from a proven component supplied through established distribution channels. Integration with existing compressed-air systems is direct, offering immediate functional gains without complex retrofits. For technical consultation, delivery options and integration support for the Kukamet 652 pneumatic clamp, contact Metav Werkzeuge for professional advice and reliable supply from Emmerich. Technical Data Article number: 652-3-D-C3 Manufacturer: Kukamet Model: 652 Facts Holding force (max): 2,500 N Pneumatic force (max): 2,000 N Arm length: 167 mm Clamping angle: 90° eClass: 21021004 ETIM: EC011973 Special features Vertical-foot mounting Zinc-plated finish Massive holding arm Pneumatic actuation Category: Clamps FAQ What clamping forces can be expected from this unit? The Kukamet 652 pneumatic clamp provides a holding force of up to 2,500 N with pneumatic actuation delivering up to 2,000 N, suitable for demanding production clamping tasks. How is the clamp mounted to a fixture? Mounting is by a vertical foot designed for secure attachment; the vertical-foot mounting and 90° clamping angle allow compact installation in standard fixture plates. Is the surface finish suitable for workshop environments? Yes. The clamp features a zinc-plated finish that offers corrosion resistance and helps maintain performance in typical workshop atmospheres. What applications is the clamp best suited for? The device is intended for jigs, fixtures, assembly and light machining operations where fast pneumatic actuation and consistent clamping force improve throughput and part quality. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 66mm Horizontal Clamp With 1000N Closing Force, Zinc Plated, Massive Arm & Safety Lock - Kukamet
Combining a massive holding arm, 1,000 N clamping force and a zinc-plated finish yields a compact, robust fixture that secures workpieces reliably in demanding shop environments; order directly via Metav Werkzeuge or consult our specialists for integration advice. Horizontal clamp 112 — zinc-plated, 1,000 N clamping force, vertical-foot mount (Kukamet) Horizontal clamp 112 is a compact lever-style clamp designed for secure horizontal fixturing in metalworking and general workshop applications, mounted via a vertical foot for 90° operation. *Zinc-plated steel body for corrosion resistance *1,000 N maximum clamping force *Massive holding arm with safety lock *Vertical-foot mounting, 90° operation Consistent holding for repeatable production The combination of a 1,000 N clamping force and a 1,200 N holding force provides a clear technical basis for repeatable fixture performance in small-batch production or jigs. The lever mechanism is configured for horizontal action at 90°, ensuring the clamping direction is constant and predictable. A massive holding arm with an integrated safety lock reduces the risk of unintentional release during machining or assembly, which contributes to process reliability and fewer reworks. Thanks to the robust mechanical design, cycle-to-cycle variation is minimised, supporting tighter tolerances on finished parts. Space-saving design that integrates easily into jigs With a vertical-foot mounting and a compact 66 mm arm, this clamp is intended for fixtures where space is limited but secure holding is mandatory. The low profile and small mass (approx. 0.2 kg) facilitate multiple mounting positions without adding bulk to a fixture plate. The zinc-plated finish protects exposed surfaces, helping maintain appearance and function in humid or mildly corrosive workshop atmospheres. These characteristics make the clamp suitable for retrofitting into existing tooling layouts or for inclusion in new fixture concepts where accessibility and orientation are constraints. Robust materials and simple upkeep for long service life Constructed from zinc-plated steel and featuring a massive holding arm, the clamp is built to withstand workshop conditions while keeping maintenance straightforward. The lever action and the mechanical safety catch are designed for long duty cycles with minimal interventions; routine checks and lubrication are generally sufficient to preserve function. The simple geometry avoids complicated service procedures, enabling faster turnaround during maintenance windows and reducing overall downtime. For purchasers seeking dependable clamping hardware from a trusted supply channel, the unit’s specification supports continued operation with predictable maintenance effort. For supply, compatibility checks or delivery from stock, contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com; our specialists advise on application and fast dispatch Technical data Article number: 112-2-D-L-C1 GTIN: 8680731500448 Manufacturer: Kukamet Facts Arm: 66 mm Angle: 90° Maximum clamping force: 1,000 N Maximum holding force: 1,200 N Weight: 0.2 kg EClass: 21041719 ETIM: EC011973 Special features Material: zinc-plated steel Mounting: vertical foot Massive holding arm Safety lock Category: clamps FAQ What is the maximum clamping force of the clamp? The clamp delivers a maximum clamping force of 1,000 N; the holding capacity is specified as 1,200 N for the Horizontal clamp 112 (SKU 112-2-D-L-C1). Is the clamp suitable for humid or mildly corrosive environments? The zinc-plated steel finish provides corrosion resistance, making the clamp suitable for workshops where occasional moisture or mild corrosion risk is present. How is the clamp mounted and what is the operating angle? Mounting is via a vertical foot and the clamp operates at a 90° angle, enabling horizontal clamping action while saving fixture plate space. What safety features are incorporated? A mechanical safety lock is integrated into the lever system and the design includes a massive holding arm to reduce the chance of accidental release. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 66mm Horizontal Clamp with Heavy Duty Arm, Safety Locked, 1,200 N Holding Force - Kukamet
Benefit from a robust, compact clamping solution that combines a massive holding arm, a secure safety lock, and galvanised corrosion resistance for dependable fixture performance. Order the Horizontal clamp 111 directly via Metav Werkzeuge or consult our specialists for application advice. Horizontal clamp 111 — Kukamet horizontal lever clamp with 66 mm arm and safety lock The Horizontal clamp 111 is a compact horizontal lever clamp designed for reliable fixture and assembly work, offering a strong holding capability and a galvanised finish for extended service life. Robust holding arm with safety lock Zinc-plated for corrosion resistance Holding force up to 1,200 N Compact 66 mm arm and 90° locking Dependable clamping power for fixtures and jigs The clamp delivers reliable holding force and controlled pressure that suits repetitive assembly and jigging operations. With a maximum holding force of 1,200 N and a maximum pressure of 1,000 N, the device provides the mechanical stability required for secure workholding. The safety-locking mechanism reduces the risk of unintended release during handling, while the massive arm construction minimises elastic deformation under load. These technical characteristics translate into fewer repositioning steps and more consistent process quality in production environments. Long service life thanks to corrosion protection and compact design Constructed from galvanised steel, the unit resists corrosion in workshop environments and maintains dependable operation over time. The small 66 mm arm and the 90° locking position make the clamp suitable for tight fixture layouts where space is limited. At just 0.2 kg, the component adds minimal mass to assemblies, simplifying jig balance and reducing dynamic stresses during automated handling. The horizontal mounting foot ensures a low-profile attachment to plates and rails, enabling straightforward integration into existing tooling. Easy integration and safe operation in production workflows As a lever clamp with horizontal base mounting, the product supports fast manual locking and quick visual confirmation of engagement, improving throughput at assembly stations. The safety lock provides secondary retention to prevent accidental opening, which benefits both manual workbenches and automated cells where inadvertent release can cause downtime. The compact form factor and standardised mechanical parameters make it suitable for serial installations, reducing complexity when specifying multiple clamping points and simplifying spare-part management. For secure and immediate supply of Kukamet lever clamps, contact Metav Werkzeuge for product selection and delivery from our Emmerich stock; our specialists are available at info@metav-werkzeuge.com or +49 2822 7131930. Technical Data Article number: 111-2-D-L-C1 GTIN: 8680731500097 Manufacturer: Kukamet eCl@ss: 21041719 ETIM: EC011973 Facts Arm length: 66 mm Locking angle: 90° Maximum pressure force: 1,000 N Maximum holding force: 1,200 N Weight: 0.2 kg Special features Galvanised (zinc-plated) finish Waagerechter Fuß (horizontal foot) mounting Massive holding arm and safety-locking Lever clamp type (lever action) Catalogue PDF available FAQ What materials can be clamped with this device? The Horizontal clamp 111 is designed for general workholding; its galvanised steel construction suits common workshop materials and fixture components rather than acting as a cutting or machining tool. How is the clamp mounted to a fixture plate? Mounting is effected via the horizontal foot; the clamp’s low-profile base allows attachment to plates or rails in standard jig and fixture setups. How does the safety lock function improve operational safety? The safety lock secures the lever in the engaged position, preventing accidental release and maintaining the set clamping force during handling and intermittent loads. Is the 66 mm arm suitable for confined spaces? Yes. The 66 mm arm combined with a 90° locking position provides a compact footprint that is beneficial in tight fixture arrangements. Are technical drawings or catalogue pages available for planning? A catalogue PDF is available for specification and planning purposes, showing dimensions and installation guidance for the Horizontal clamp 111. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 66mm Horizontal Clamp With Massive Holding Arm, 1,200N Holding Force, Zinc Plated - Kukamet
Take advantage of the combination of a solid holding arm, galvanised construction and compact form factor for consistent clamping in fixtures and jigs. Order the component directly via Metav Werkzeuge or consult our specialists for application advice. 111 horizontal clamp by Kukamet — Solid-arm design, galvanised steel The 111 horizontal clamp is a compact horizontal clamping unit designed for secure fixture and jig applications in workshops and light industrial environments. Solid holding arm for increased stability Galvanised steel for corrosion resistance 1200 N retaining force, 1000 N clamping force Horizontal foot mount with 90° clamping angle Reliable clamping performance for machining and assembly The clamp delivers clear, measurable performance: a clamping force (1000 N) for workpiece securing and a higher retaining force (1200 N) to resist lateral movement during handling. These figures support repeatable, process-stable results when used in small-series production or fixture setups. The forces quoted refer to static capacities under recommended mounting conditions; this ensures predictable behaviour during light machining, assembly or inspection tasks. Such quantified performance facilitates integration into process planning and reduces the need for over‑engineering of fixtures. Durable construction that lowers maintenance needs A galvanised finish protects the unit against corrosion, extending service life in humid or mildly corrosive environments. The clamp’s solid holding arm is engineered for torsional rigidity, reducing deflection under load and maintaining alignment of clamped parts. The compact 66 mm arm length supports close-packed fixturing without compromising stability. This combination of protective coating and robust geometry results in fewer replacements and less unscheduled downtime, which contributes to measurable savings over the lifespan of the fixture. Space-efficient layout for versatile fixture design The horizontal foot mounting and the 90° clamping orientation allow the clamp to be positioned flush to surfaces or rails, optimising bench and fixture real estate. The 90° clamping angle provides a consistent stop for workpieces, simplifying repeatable positioning in jigs. The compact footprint is particularly valuable for modular tooling systems where accessible clamping and unobstructed tool paths are critical. This design supports both manual and semi‑automated processes by keeping the clamp out of the immediate work envelope while still delivering secure hold. Straightforward specification and workshop suitability Identified by SKU and GTIN for easy procurement, the clamp is suitable for workshop and small industrial settings that require robust, easy-to-specify components. The combination of measurable forces, a 66 mm arm and a galvanised finish makes the unit a practical choice for general fixturing tasks, repetitive assembly or inspection stations. The design is compatible with common bench and fixture standards, enabling rapid retrofitting into existing jigs. The 111 is therefore a reliable building block for consistently repeatable clamping solutions. For tailored application advice or to secure the Kukamet 111 horizontal clamp for your fixtures, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and supply from Emmerich Technical data SKU: 111-2-D-C1 GTIN: 8680731500066 Category: Spanner ETIM: EC011973 ECLASS: 21041719 Facts Arm length: 66 mm Clamping force: 1000 N Retaining/holding force: 1200 N Clamping angle: 90° Weight: 0.204 kg Special features Material: galvanised steel Mounting: horizontal foot Massive/solid holding arm Suitable for fixture and jig applications FAQ What clamping and holding forces does the unit provide? The unit provides a clamping force of 1000 N and a retaining (holding) force of 1200 N as specified for the Kukamet 111 horizontal clamp. Is the clamp suitable for use in humid or mildly corrosive environments? Yes, the galvanised finish of the clamp offers corrosion resistance, making it suitable for humid conditions and typical workshop atmospheres. Can the clamp be mounted on common bench plates or T-slot rails? The clamp uses a horizontal foot mount and a 90° clamping orientation, which allows mounting on flat surfaces and many standard fixture layouts. How does the arm length affect fixture layout? The 66 mm arm length provides a compact reach that supports dense fixture arrangements while maintaining effective leverage and stability. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 66mm Horizontal Clamp With Solid Arm, 1,000 N Thrust / 1,200 N Hold - Kukamet
Take advantage of a compact, robust clamping solution that combines a solid holding arm with reliable forces of up to 1,200 N for repeatable fixation in small jigs and fixtures. Order the unit through Metav Werkzeuge or contact our consultants for technical advice and stock information. Horizontal Clamp 111 — Horizontal lever clamp with 1,200 N holding force (Kukamet) A Horizontal Clamp 111 designed as a horizontal lever clamp for secure workpiece fixation in machining, assembly and inspection setups, offering a compact footprint and dependable repeatability. Solid 66 mm holding arm Horizontal foot for flush mounting 1,200 N max holding force 90° locking angle, robust lever Stable clamping in confined workspaces The clamp is engineered for fixtures where space is limited and repeatable results are required. Its solid holding arm with a length of 66 mm provides a stable contact area, while a lightweight body (approx. 0.204 kg) keeps fixture mass low. The rated 1,200 N holding force is provided by the lever mechanism, enabling consistent retention of components during light machining and assembly tasks. For planners and production engineers, this combination reduces rework and accelerates setup cycles without adding significant mass to the jig. Precise mounting and reliable locking Designed with a horizontal foot for flush or base mounting, the device is suited to perpendicular and lateral clamping arrangements on workbenches and tooling plates. The 90° locking angle ensures a clear audible and tactile engagement, simplifying operator verification of a secure clamp. The lever action converts manual input into a controlled clamping force; explained simply, the mechanical linkage amplifies hand movement into holding force, which means consistent clamping pressure is achieved with limited operator effort. Durable finish and straightforward integration A blackened finish provides basic surface protection and reduces glare in bright production environments, while the massive holding arm and robust lever design are intended for repetitive industrial use. The compact unit integrates smoothly into modular fixture systems and can be combined with standard dowels and fasteners for quick retrofitting. Component identification is straightforward for procurement and inventory: SKU B111-2-D-C1 and GTIN are available for ordering and traceability purposes. Contact Metav Werkzeuge for delivery options and technical guidance on the Kukamet horizontal lever clamp from our Emmerich stock. Technical data Article number: B111-2-D-C1 GTIN: 8680731506952 Manufacturer: Kukamet Facts Arm length: 66 mm Angle: 90° Weight: 0.204 kg Max clamping force: 1,000 N Max holding force: 1,200 N Special features Solid/massive holding arm Horizontal foot for flush/base mounting Blackened finish Robust lever mechanism FAQ What maximum holding force does the clamp provide? The clamp delivers a maximum holding force of 1,200 N for secure retention; the mechanical drive also allows a maximum clamping thrust of 1,000 N for operational force considerations. Is the clamp suitable for mounting on a flat tooling plate? Yes. The horizontal foot design allows flush mounting on tooling plates and ensures stable positioning in modular fixtures for machining and assembly. How compact is the unit for confined fixtures? With a 66 mm holding arm and a weight of approximately 0.204 kg, the clamp is compact and well suited to confined workstations and lightweight jigs. What surface protection does the clamp have? The device features a blackened finish that provides basic corrosion resistance and reduces reflected light in bright environments. Which SKU should be ordered for inventory and procurement? Order using SKU B111-2-D-C1; the GTIN 8680731506952 is available for catalogue and system entry. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 682 Pneumatic Clamp Without Cylinder, 6500 N Thrust / 30000 N Hold, Galvanised - Kukamet
Benefit from a 30,000 N maximum holding force combined with a 6,500 N clamping capacity in a galvanised pneumatic clamp supplied without an integrated pneumatic cylinder; this combination delivers robust fixture retention and straightforward integration into existing actuator systems. Order or request specification support via Metav Werkzeuge for reliable delivery and technical consultancy. Kukamet 682 Pneumatic clamp — galvanised, 30,000 N holding force The Kukamet 682 is a heavy-duty pneumatic clamp designed for horizontal-foot mounting in industrial fixturing, supplying high holding and clamping capacities while allowing external actuation. Galvanised construction for corrosion resistance Maximum holding force 30,000 N Maximum clamping force 6,500 N Horizontal-foot mounting for stable installation Dependable clamping capacity for demanding fixtures The clamping unit delivers a high holding force of 30,000 N and a clamping force of 6,500 N, ensuring secure retention of workpieces in repetitive production and machining tasks. These figures indicate suitability for medium to heavy-duty fixturing where reliable workpiece retention prevents slippage and reduces rework. The numerical performance supports planning of fixture layouts and cycle times and allows comparison with alternative clamping solutions. Corrosion resistance and mechanical longevity Constructed with a galvanised surface, the device resists corrosion in workshop environments and maintains consistent contact geometry over long service intervals. The protective finish reduces the frequency of surface maintenance and minimises the risk of contamination in production processes. The relatively compact mass of 11.6 kg balances robustness with manageable handling during installation, while the zinc coating supports longevity under typical shop-floor conditions. Flexible integration and mounting advantages With a horizontal foot mounting arrangement, the clamp is intended for stable attachment to fixture plates and subplates, simplifying alignment within modular tooling systems. Supplied without a pneumatic cylinder, the unit is compatible with third-party actuators or central pneumatic systems, allowing planners to select stroke and pressure characteristics that match specific cycle requirements. The design therefore supports customisation of actuation while keeping the clamp’s core mechanical ratings constant. Practical operation and service considerations The mechanism’s straightforward design reduces downtime for routine inspection and replacement of wear parts. Where regular cycle rates and high clamping loads are expected, the clear specification of maximum holding and clamping forces enables maintenance scheduling based on measured loads rather than guesswork. Integration into production cells benefits from the unit’s clear numeric data and the absence of an integrated cylinder, which simplifies both procurement and spares management. Contact Metav Werkzeuge for tailored integration advice or to arrange procurement from Emmerich; technical consultants are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: 682-8-M Model: 682 GTIN: 8680731505108 ETIM: EC011973 Core figures Maximum holding force: 30,000 N Maximum clamping force: 6,500 N Weight: 11.6 kg Materials & features Galvanised surface Horizontal foot mounting Supplied without pneumatic cylinder Category: Clamp FAQ What is the maximum holding force of the Kukamet 682? The Kukamet 682 pneumatic clamp provides a maximum holding force of 30,000 N, specified for stable retention in demanding fixturing applications. Is a pneumatic cylinder included with the clamp? No, the clamp is supplied without a pneumatic cylinder, enabling integration with external actuators or central pneumatic systems to match specific stroke and pressure requirements. What mounting arrangement does the device use? The unit features a horizontal foot mounting style, designed for secure attachment to fixture plates and modular tooling systems. Which surface treatment does the clamp have? The clamp is galvanised, offering corrosion resistance suitable for industrial workshop environments and reducing surface maintenance. How heavy is the clamp and does weight affect installation? The device weighs 11.6 kg, a mass that balances durability with manageable handling during installation and alignment. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 68mm Horizontal Clamp With Massive Clamping Arm And Safety Lock, 2300 N Closing Force - Kukamet
Robust combination of a galvanised body, massive holding arm and up to 2,500 N holding force ensures secure, repeatable clamping for jigs and fixtures; order the Horizontal clamp 112 directly via Metav Werkzeuge or consult their specialists for application advice. Horizontal clamp 112 — Kukamet horizontal toggle clamp with vertical-foot mounting and 2,500 N holding force A Horizontal clamp 112 engineered for reliable workholding in fixtures and production jigs, mounted on a vertical foot for compact installation and rapid lever action clamping. Galvanised steel construction 68 mm arm reach for compact fixtures Up to 2,500 N holding force Vertical-foot mounting for low-profile set-ups Safety locking mechanism and robust arm Secure, measurable clamping for series production The clamp provides clearly defined performance values: a maximum clamping force (push) of 2,300 N and a maximum holding force of 2,500 N, specified in newtons for objective comparison in procurement and machine design. These figures support predictable seating forces when securing parts for machining, assembly or inspection, reducing rework. The massive holding arm and integrated safety locking convert lever motion into a positive toggle action that resists accidental release, which is particularly valuable in repetitive tasks where consistent clamping is essential. Compact mounting and fast cycle times Designed for installation on a vertical foot, the clamp minimises lateral space while delivering a horizontal clamping action at a right angle (90°). The 68 mm arm reach balances compactness with clearance for most small to medium fixtures; at only 0.3 kg the component adds negligible mass to a jig while remaining robust. The lever-style mechanism permits rapid engagement and disengagement, improving throughput on manual pick-and-place or semi-automated stations. Where set-up time is critical, the clamp’s simple mechanics allow quick integration without complex drives or pneumatics. Durability and low-maintenance operation for the workshop Constructed from galvanised steel, the unit resists corrosion and keeps maintenance intervals long even in humid environments. The solid arm and zinc coating ensure longevity under frequent cycling, while the simple mechanical design reduces points of failure. Specification and SKU data allow traceability in procurement and spare-part planning: the model is a straightforward toggle clamp suited to production environments where reliability and predictable performance are the primary criteria. For robust, repeatable clamping with a galvanised 2,500 N hold, contact Metav Werkzeuge for purchase options and technical advice. Technical Data SKU: 112-3-D-L-C1 GTIN: 8680731500523 eClass: 21041719 ETIM: EC011973 Facts Arm length: 68 mm Angle: 90° Weight: 0.3 kg Max clamping force: 2,300 N Max holding force: 2,500 N Materials & Features Material: Galvanised steel Mounting: Vertical foot Massive holding arm Safety locking mechanism Category: Clamp / toggle clamp FAQ What maximum holding force does this clamp provide? The Kukamet Horizontal clamp 112 delivers a maximum holding force of 2,500 N, specified to support predictable workholding in fixtures. How is the clamp mounted in a jig or fixture? Mounting is via a vertical foot; the design provides a low-profile horizontal clamping action suited for compact fixture layouts. Is the clamp suitable for corrosive or humid environments? The galvanised steel construction of the Horizontal clamp 112 offers enhanced resistance to corrosion compared with untreated steel, extending service life in damp conditions. What is the effective arm reach and how does it affect clearance? The clamping arm measures 68 mm, providing a balance between compact installation and sufficient clearance for small to medium workpieces. Does the clamp include a safety mechanism to prevent accidental release? Yes, the unit features a safety locking mechanism and a robust holding arm to prevent unintended opening during operations. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 68mm Horizontal Clamp With Massive Holding Arm And Safety Lock, 2.3kN Thrust - Kukamet
Take advantage of the combination of compact design, high holding force and a secure safety lock for reliable clamping in fixtures and jigs. Order the Horizontal clamp 112 directly via Metav Werkzeuge or ask the consultants for application-specific advice. Horizontal clamp 112 — 68 mm arm, 90° lever clamp (Kukamet) The Horizontal clamp 112 is a robust 90° lever clamp designed for secure horizontal workholding in jigs, fixtures and fixed machining stations. Massive hold arm with safety lock 68 mm arm for compact setups Holding force up to 2,500 N Vertical-foot mounting for fixed stations Consistent, measurable clamping performance for production use The clamp delivers quantifiable results: clamping force of 2,300 N and a holding force of 2,500 N, providing stable fixation during machining and assembly operations. These values translate into fewer rework cycles and a predictable process window when the clamp is integrated into repetitive production tasks. The lever mechanism ensures quick actuation while the pressure figures support use with medium-duty fixtures, making the component suitable for series production and workshop jigs alike. Space-saving format that eases fixture design With a compact 68 mm arm and an overall mass close to 0.3 kg, the unit is intended for applications where space is limited but process reliability remains essential. The vertical-foot mounting facilitates direct attachment to plates and bases without elaborate adapters, simplifying layout and reducing setup time. The 90° lever orientation helps keep the clamping profile low, allowing close stacking of clamps on a fixture plate and efficient use of working area. Built for durability and operator safety Constructed with a blackened finish for surface protection and featuring a massive hold arm and mechanical safety lock, the clamp is designed to withstand regular workshop use while maintaining consistent clamping geometry. The safety lock prevents accidental release under load, supporting safer changeover procedures and reducing the risk of component movement during machining. The robust build quality reduces long-term maintenance requirements and contributes to consistent process quality. Easy integration into standard tooling and fixtures As a 90° lever clamp, the unit is compatible with a wide range of jigs, fixtures and assembly stations where repeatable horizontal clamping is required. The combination of compact dimensions, measurable force ratings and standard mounting style enables rapid substitution into existing setups or incorporation into new fixture designs. For buyers seeking a reliable, no-frills clamping solution for medium-duty applications, this lever clamp offers a practical balance of performance and simplicity. Choose Kukamet’s Horizontal clamp 112 for secure, repeatable clamping — contact Metav Werkzeuge for procurement guidance or detailed technical clarification. Technical data Article number: B112-3-D-L-C1 Manufacturer: Kukamet eCl@ss: 21041719 ETIM: EC011973 Facts Arm length: 68 mm Clamping force (max): 2,300 N Holding force (max): 2,500 N Angle: 90° Weight: 0.3 kg Special features Vertical-foot mounting Massive hold arm Safety locking mechanism Blackened finish 90° lever clamp FAQ What clamping and holding forces does the clamp provide? The clamp achieves a maximum clamping force of 2,300 N and a holding force up to 2,500 N, suitable for medium-duty workholding applications. Can the clamp be mounted on a fixture plate? Yes, the vertical-foot mounting is designed for direct attachment to plates and bases, enabling straightforward integration into fixtures. What material protection is applied to the surface? The component has a blackened finish for surface protection and improved wear resistance during workshop use. Is there a safety feature to prevent accidental release? A mechanical safety lock is incorporated to prevent unintended opening under load and to support safe operation during changeovers. Which SKU identifies this model for ordering? The clamp is listed under SKU B112-3-D-L-C1 for procurement and inventory purposes. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
90° 68mm Horizontal Clamp With Massive Holding Arm, 2.5kN Hold, 2.3kN Thrust - Kukamet
Take advantage of a compact, robust lever clamp that combines a massive holding arm with a high clamping capability to secure components reliably in tight fixtures. The combination of a 68 mm reach, a vertical-foot mounting and proven holding capacity supports steady production processes. Order directly via Metav Werkzeuge or consult the technical team for integration advice. Kukamet Horizontal Clamp 112 — 68 mm reach, 2,300 N clamping force The Horizontal Clamp 112 is a compact lever clamp designed for secure horizontal workholding in jigs, fixtures and small assembly stations. Massive holding arm for extra rigidity 68 mm reach for compact clamping setups 2,500 N maximum holding force Vertical-foot mounting for stable installation Stable contact and repeatable positioning A massive holding arm and defined lever geometry deliver consistent pressure across cycles, transforming applied actuation into a reliable clamping result. With a rated 2,300 N clamping force and a 2,500 N holding force, the unit keeps workpieces immobile during machining or assembly, reducing rework and inspection time. The design supports precise positioning in production tooling, where stable contact and repeatability are essential for quality assurance. Compact layout for space-constrained fixtures The compact 68 mm reach and right-angled orientation make this clamp suited to dense fixture arrangements and small workstations. The vertical-foot mounting allows secure attachment to baseplates or tooling plates while keeping the clamping profile low. At approximately 0.292 kg, the component contributes minimal mass to moving subassemblies, simplifying dynamic balance and handling in automated setups. Durable finish and dependable duty cycle A blackened finish provides basic surface protection and a uniform appearance that resists light abrasion in workshop environments. The clamp operates as a lever clamp, converting operator or machine input into a strong holding action with minimal maintenance requirements. Specified forces indicate suitability for repetitive clamping tasks in production runs, and the construction supports long-term wear resistance under typical industrial conditions. Easy integration into existing tooling systems Mounting by a vertical foot and a 90° working angle allow straightforward incorporation into existing fixture plates and jig systems. The compact form factor and clear mechanical specification simplify layout calculations and ensure predictable interaction with neighbouring clamps or locators. The robust arm and defined force ratings support secure workholding without complex adjustments, enabling efficient setup changes and reduced downtime. Enquire with Metav Werkzeuge for tailored integration advice or a quotation on the Kukamet Horizontal Clamp 112 — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: B112-3-D-C1 GTIN: 8680731507232 Manufacturer: Kukamet Facts Arm length: 68 mm Clamping force, max: 2,300 N Holding force, max: 2,500 N Angle: 90° Weight: 0.292 kg Special features Mounting: vertical foot Material/finish: blackened finish Massive holding arm Category: Clamps FAQ What materials is this clamp suitable for? The Kukamet Horizontal Clamp 112 is a mechanical lever clamp suitable for general workholding applications; material compatibility depends on the fixture design rather than the clamp itself. How does clamping force differ from holding force? Clamping force (2,300 N for this model) refers to the generated actuation pressure, while holding force (2,500 N) indicates the maximum static retention capacity once the clamp is engaged in the Kukamet Horizontal Clamp 112. What mounting options are available? This model features a vertical-foot mounting style for attachment to baseplates and tooling plates, enabling low-profile installation in jigs and fixtures. Is the clamp corrosion-resistant? The blackened finish provides basic surface protection and improved wear characteristics for workshop environments when used as intended with the Kukamet Horizontal Clamp 112. Can the clamp be used in automated production cells? Yes, the compact design, defined force specifications and repeatable lever action make the clamp suitable for use in automated fixtures and assembly stations where mechanical actuation is compatible. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Fast, secure workpiece clamping with toggle clamps
Toggle clamps, also known as knee lever clamps or lever clamps, are mechanical clamping elements used to fix components quickly and reliably in fixture construction, assembly, welding and testing. Their kinematic knee lever principle provides a one-motion closure that locks beyond a mechanical dead centre, delivering consistent clamping force with minimal operator effort.
How the locking principle benefits production
The kinematic dead-centre action means the clamp self-locks once closed, so no continuous force is required on the handle and the workpiece remains form-stable even under process-induced vibration. That behaviour translates directly into higher process reliability and faster cycle times: operators close the clamp in one swift move, parts stay in position during machining or inspection, and changeover times are reduced.
Practical advantages for everyday workshop use
- Reduced set-up time through single-motion clamping
- Consistent repeatability and process stability under vibration
- High holding force with low operator effort thanks to the dead-centre mechanism
- Durable construction for long service life in repetitive production
- Versatile mounting options for vertical, horizontal, push‑rod and draw applications
Technical overview
- principle: kinematic knee lever (dead-centre) locking
- application areas: fixture construction, assembly, welding, testing
- design variants: vertical clamp, horizontal clamp, push-rod clamp, draw/closure clamp
- material: high-strength zinc-plated steel; stainless steel options
- handle: ergonomic, oil-resistant handles
- joints: wear-resistant joint bushes
- process suitability: holds under strong, process-induced vibration; enables high repeatability
Metav as your precision partner
Metav combines decades of specialist knowledge with a broad, dependable assortment for industry and trade. With more than 48,000 customers, a catalogue exceeding 250,000 products and a quality filter based in Emmerich, Metav offers a practical, low-risk route to robust toggle clamps and accessories—ideal for buyers who need dependable stock, expert selection and consistent product quality.
In short: toggle clamps (knee lever clamps / lever clamps) deliver rapid, repeatable clamping with minimal operator effort, making them a straightforward productivity upgrade for demanding production environments.
FAQ
What exactly is a toggle clamp and how does it lock?
A toggle clamp uses a kinematic knee lever that passes a mechanical dead centre during closure; once over‑centre, the clamp self-locks, maintaining clamping force without continuous pressure on the handle.
Which toggle clamp type should I choose for sheet assembly or for pulling covers together?
Use vertical or horizontal toggle clamps for holding sheets and assemblies; choose draw/closure clamps when axial pulling or form closing is required. The variety of toggle clamp designs matches different fixture geometries and force directions.
Are toggle clamps suitable for high-vibration processes?
Yes. The dead‑centre locking of toggle clamps secures the workpiece even under strong, process-induced vibration, ensuring positional stability during machining or testing.
What materials and handle options are available for toggle clamps?
Common materials: zinc-plated steel and stainless steel. Handles are typically ergonomic and oil-resistant; joints use wear-resistant bushes for extended service life.
Can Metav help specify the right toggle clamp for my application?
Metav supplies a wide selection of toggle clamps and technical information, enabling selection based on application, material and required holding force; the assortment is supported by decades of precision experience and a large customer base.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com