CPMT 060208 AH6225 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp, stable cutting edge, universal applicability for stainless steel and ISO compatibility to keep turning operations reliable and productive; order directly via Metav Werkzeuge or request application advice from the consultants. CPMT060208 AH6225 — Tungaloy turning insert (ISO CPMT) A CPMT060208 AH6225 rhombic turning insert designed for external and internal turning, engineered for universal use on stainless steel with a sharp, stable cutting edge. PVD-coated carbide grade AH6225 ISO CPMT 06 (060208) compatible design Rhombic plate with 11° clearance angle Cylindrical hole with one-sided countersink 40°–60° Reliability and cutting performance for turning The CPMT060208 AH6225 insert combines a PVD-coated carbide substrate with a geometry optimised for medium cutting depths, delivering a sharp, stable cutting edge that is particularly suited to machining stainless steel. The PVD layer reduces flank wear under variable conditions, which translates into more predictable tool life and fewer interruptions in production. For operations where consistent surface finish and repeatability matter, the engineered grade ensures efficient metal removal while maintaining dimensional accuracy. Clear compatibility to reduce setup time Compatibility with toolholders is determined by form, clearance angle 11°, tolerance class, fastening method, size and thickness. The ISO CPMT form and ISO designation 060208 allow straightforward selection of suitable external holders or boring bars and fitting components. Specifying the plate size (06) and the 2.38 mm thickness avoids mismatches at the tool post, reducing setup iterations. Clear guidance on mounting geometry helps maintain clamping security and repeatable cutting conditions for series production. Productivity through controlled chip formation The single-sided chipbreaker and the universal AH6225 grade are designed to promote stable chip control when machining stainless steel, which supports higher uninterrupted cycle times. A modest corner radius 0.8 mm balances edge strength with cutting efficiency, enabling reliable performance across mixed batch operations. By focusing on chip control and a robust edge, the insert helps reduce tool-change frequency and supports a predictable process cost per component. Practical assembly and system approach The recommended system comprises the ISO insert plus a matching external holder or boring bar, an appropriate underlay/clamping set and replacement screws. The plate’s cylindrical hole with countersink (40°–60°) ensures secure clamping and simplifies alignment during replacement. Using standardised ISO components streamlines inventory and spare-part management, while the insert’s geometry supports both external and internal turning tasks with minimal rework between setups. Contact Metav Werkzeuge for an application check or a tailored recommendation for the Tungaloy CPMT060208 AH6225 turning insert and compatibility advice Technical data Article number: 6951141 SKU: 6951141-Tungaloy Manufacturer SKU: TUN6951141 Model series: ISO turning inserts Grade: AH6225 Material: Hartmetall Facts ISO designation: 060208 Plate size: 06 Thickness: 2.38 mm Corner radius: 0.8 mm Clearance angle: 11° Main angle: 80° Special features PVD-coated carbide Rhombic plate (CPMT) Cylindrical hole with one-sided countersink (40°–60°) Single-sided chipbreaker Designed for stainless steel Compatible with ISO holders and boring bars FAQ What materials is this insert suitable for? The AH6225 grade is formulated for machining stainless steel; the CPMT060208 geometry supports both external and internal turning tasks. How does the AH6225 PVD coating benefit machining? The PVD-coated carbide of the AH6225 grade on the CPMT insert improves wear resistance and helps maintain a stable cutting edge under varying conditions, resulting in more consistent tool life. Which holder features are required for correct compatibility? Compatibility depends on holder form, fastening method, tolerance class, size and thickness; the ISO CPMT 06 form and 2.38 mm thickness should match the chosen holder or boring bar. What does the 0.8 mm corner radius influence? A corner radius of 0.8 mm increases edge strength compared with finer radii, improving robustness in interrupted cuts while preserving an acceptable surface finish. Is the insert supplied with screws or shims? The product is the indexable plate; the standard system includes the ISO insert plus a matching holder, underlay/clamping set and replacement screws available separately. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 AH6235 Wendeplatten - Tungaloy
A proven solution for demanding turning operations: the combination of a PVD-coated cemented carbide grade and a rhombic ISO geometry delivers increased resistance to chipping and consistent surface quality in stainless-steel and interrupted-cut applications. Order the CPMT060208 AH6235 insert directly via Metav Werkzeuge or ask the consultants for application-specific cutting data. CPMT 060208 AH6235 Tungaloy turning insert — PVD-coated carbide, 0.8 mm radius A CPMT060208 AH6235 indexable insert for turning, engineered for stainless steels and interrupted cuts with a rhombic ISO geometry and single-sided chipbreaker. PVD-coated carbide grade AH6235 Suited to stainless steel and interrupted cuts Rhombic ISO CPMT 060208, 11° clearance 0.8 mm corner radius, 2.38 mm thickness Robust edge performance for interrupted cuts and stainless steel The CPMT060208 AH6235 insert is a PVD-coated cemented carbide plate developed to reduce edge failure in high-risk conditions. The AH6235 grade is intentionally tougher, which enhances resistance to fracture during interrupted cuts and when machining stainless steels. The 0.8 mm corner radius balances edge strength and surface finish, so chip formation remains controlled while flank wear is delayed. This results in fewer tool changes and more stable cycle times on the shop floor. Consistent process reliability through coating and geometry A thin, uniform PVD layer improves the insert’s adhesion properties and increases resistance to built-up edge without compromising toughness. The rhombic ISO geometry and an 11° clearance support secure engagement and predictable cutting forces; the single-sided chipbreaker is designed to promote reliable chip control in typical turning operations. Together, coating and geometry contribute to steady tool life and repeatable part quality—advantages that enhance throughput and reduce unplanned downtime. Clear mounting and system compatibility for easy integration Compatibility is determined by form, clearance, tolerance class, clamping method, size and thickness; the indexable plate is intended to be used with a matching external holder or boring bar, plus an appropriate shim/clamp set and replacement screws. Correct selection of the clamping components ensures rigid fixation and minimises vibration, which protects the cutting edge and improves surface finish. The insert’s hole and seat dimensions are compatible with standard CPMT holders when the correct tolerance class is observed. Practical guidance for application and grade selection The CPMT format offers an 80° approach orientation that provides a robust cutting-edge alignment for external and internal turning tasks. For interrupted cuts and components with a risk of edge breakout, the AH6235 grade is recommended due to its greater fracture resistance; for highly abrasive or continuous finishing tasks, alternative grades may be considered. When choosing corner radii, smaller values favour finer surface finishes while slightly larger radii increase edge strength—select the radius that matches the required part tolerance and machine stability. Contact Metav Werkzeuge for tailored application advice, availability of Tungaloy CPMT inserts and detailed cutting data at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6903461-Tungaloy Manufacturer SKU: TUN6903461 Manufacturer article number: 6903461 Model series: ISO turning inserts Name: CPMT060208 AH6235 Tungaloy insert Core specifications Corner radius: 0.8 mm Thickness: 2.38 mm Clearance angle: 11° Insert size: 06 Included hole: with hole Hole/countersink style: cylindrical hole with one-sided countersink 40°–60° Included angle: 80° Features and applications Material: cemented carbide Coating / grade: PVD-coated AH6235 Chipbreaker: single-sided Shape: rhombic Primary application: turning Suitable for: stainless steels and interrupted cuts Recommended system: matched external holder or boring bar, shim/clamp set and replacement screws FAQ What materials is this insert suitable for? The CPMT060208 AH6235 insert is formulated for machining stainless steels and performs well in interrupted-cut conditions due to the tougher AH6235 grade. How does the AH6235 grade affect tool life? The AH6235 PVD-coated grade increases edge toughness and resistance to chipping; in practice, the CPMT060208 AH6235 insert sustains more reliable performance under interrupted cuts compared with harder, more brittle grades. Which holders are compatible with this insert? Compatibility is governed by geometry, clearance and size; CPMT060208 inserts are mounted in matching CPMT external holders or boring bars when the holder accepts ISO CPMT 060208 plates and the correct clamp and shim are used. What is the significance of the 0.8 mm corner radius? A 0.8 mm corner radius offers a compromise between edge strength and surface finish—sufficient robustness for general turning while maintaining acceptable part finish on most stainless-steel applications. Does the insert require a special chipbreaker or coolant strategy? The single-sided chipbreaker integrated in this plate supports controlled chip formation for many turning tasks; coolant strategy depends on material and cycle, but emphasising stable clamping and appropriate feed rates reduces edge stress for the AH6235 grade. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 AH725 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide AH725, ISO conformity and precise geometry for consistent process reliability and long tool life; order the CPMT060208 insert directly via Metav Werkzeuge or ask the consultants for holder compatibility. CPMT060208 AH725 — CPMT 060208 turning insert by Tungaloy, PVD-coated carbide The CPMT060208 AH725 is an ISO-standard indexable insert for turning, engineered to deliver reliable machining performance on Stahl and rostfreier Stahl in both external and internal operations. PVD-coated carbide for high process security Universal grade for Stahl and rostfreier Stahl ISO rhombic shape with 0.8 mm nose radius Cylindrical hole with 40°–60° countersink Consistent performance across mixed materials The AH725 grade is a PVD-coated carbide developed for universality and fracture resistance. Its composition and coating stabilise the cutting edge when machining Stahl and rostfreier Stahl, reducing the risk of chipping in varying material batches. This universality translates into fewer tool changes and a steadier production flow, supporting a predictable tool life and consistent surface quality even when workpiece material varies. Geometry tailored for stability and repeatability A rhombic ISO profile combined with an 80° cutting geometry and 0.8 mm nose radius ensures stable contact and repeatable form accuracy. The 11° clearance reduces rubbing and heat build-up at the flank, while the cylindrical hole with single-sided countersink (40°–60°) enables secure clamping and correct seating in compatible holders. These features make the indexable insert suitable for small-tool applications where repeatable positioning and stability are essential. Improved productivity and controlled chip formation Equipped with a single-sided chipbreaker, the insert promotes controlled chip flow and helps maintain cutting forces within stable limits. The PVD coating improves wear resistance and reduces built-up edge formation, which is especially beneficial in applications requiring high process security. For production environments aiming to balance uptime and cost efficiency, this insert offers a practical combination of performance and longevity that supports shorter cycle times and predictable maintenance intervals. Practical integration and application advice The insert is supplied as an ISO-standard component and is intended for use with matching external holders or boring bars; compatibility depends on form, clearance, tolerance class, fastening method, size and thickness. Typical applications include external and internal turning where a robust, universal grade is required. For specific holder pairing, cutting data or to select the most suitable chipbreaker for an application, consult Metav Werkzeuge for tailored recommendations and machining parameters. Secure consistent process reliability with the Tungaloy AH725 insert — contact Metav Werkzeuge for application advice and holder matching at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6856704 Manufacturer SKU: TUN6856704 Seller SKU: 6856704-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Designation: CPMT060208 AH725 Tungaloy-Wendeplatte Core specifications Nose radius: 0.8 mm Clearance angle: 11° Insert size: 06 Thickness: 2.38 mm Cutting angle: 80° Countersink angle: 40°–60° Features & materials PVD-coated carbide (AH725) Rhombic plate form Single-sided chipbreaker Cylindrical hole with one-sided countersink ISO-standard turning insert Application: Drehen FAQ Which materials is this insert suitable for? The CPMT060208 AH725 insert by Tungaloy is designed as a universal grade for machining Stahl and rostfreier Stahl, offering reliable performance across mixed batches. Is the insert compatible with standard ISO turning holders? Compatibility depends on holder form, clearance, tolerance class, fastening and thickness; the ISO profile of the CPMT060208 supports straightforward matching with standard external holders and boring bars. What benefit does the AH725 grade provide in daily production? AH725 delivers fracture resistance and stable chip formation; the PVD-coated carbide prolongs edge life and improves process reliability in both roughing and finishing passes. How does the single-sided chipbreaker affect machining? The single-sided chipbreaker controls chip flow and reduces vibration risk, supporting consistent surface finish and safer chip evacuation during turning operations. Can this insert be used for both external and internal turning? Yes — the insert’s geometry and secure clamping make it suitable for both external and internal turning tasks when paired with the appropriate holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 AH8015 Wendeplatten - Tungaloy
Take advantage of a PVD-coated carbide insert (AH8015) that balances wear resistance with edge stability, and a compact 0.8 mm corner radius with 11° clearance for reliable ISO-compatible turning operations; order the insert directly via Metav Werkzeuge or consult Metav's advisers for holder compatibility and cutting data. CPMT 060208 AH8015 — CPMT ISO turning insert for turning, PVD-coated carbide, 0.8 mm radius (Tungaloy) The CPMT060208 AH8015 is an ISO rhombic turning insert engineered for external and internal turning of heat-resistant alloys, combining a one-sided chipbreaker with a cylindrical hole and single-sided countersink for secure clamping and predictable chip formation. PVD-coated carbide for heat-resistant alloys Balanced wear resistance and edge stability Rhombic ISO insert with 11° clearance angle Cylindrical hole with single-sided countersink 40°–60° Optimised cutting performance for heat-resistant alloys The AH8015 grade is a PVD-coated carbide designed as a first choice for general machining of heat-resistant alloys, offering an even compromise between wear resistance and edge stability. The coating reduces adhesion and thermal loading at the cutting edge, which translates into longer tool life and more consistent component quality. For production environments where repeatability matters, this insert provides predictable tool change intervals and contributes to reduced process variability. Geometry that ensures secure clamping and consistent surface finish The combination of a rhombic ISO profile with an 11° clearance angle and a 0.8 mm corner radius improves stability during light to medium cuts while maintaining a defined cutting edge for acceptable surface finishes. The one-sided chipbreaker promotes controllable chip formation for turning operations, and the cylindrical hole with a single-sided countersink (40°–60°) ensures positive seat and repeatable alignment in standard ISO holders. Such geometry minimises chatter risk and supports reliable dimensional control. Simple integration into ISO turning systems for efficient workflow The component functions as part of a system: an ISO turning insert paired with an appropriate external holder or boring bar, plus the necessary clamping set and replacement screws. Compatibility depends on form, clearance, tolerance class, fixing method, size and thickness, so the selection of holder and clamp should follow these parameters to achieve optimal performance. The grade and chipbreaker selection can be adapted according to workpiece material and machine stability to balance productivity and tool life. For tailored advice on using Tungaloy’s AH8015 grade or to confirm holder compatibility for the CPMT 060208, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 6951203 Manufacturer SKU: TUN6951203 SKU: 6951203-Tungaloy Designation: CPMT060208 AH8015 Model series: ISO turning indexable inserts Manufacturer: Tungaloy Core specifications Insert size: 06 Thickness: 2.38 mm Corner radius: 0.8 mm Clearance angle: 11° Included angle: 80° Hole: cylindrical with single-sided countersink (40°–60°) Design & special features Rhombic shape (ISO CPMT) One-sided chipbreaker PVD-coated carbide grade AH8015 For turning: external and internal Compatibility determined by shape, clearance, tolerance class, fixing, size and thickness With hole and single-side countersink for positive clamping FAQ Is this insert suitable for machining heat-resistant alloys? The AH8015 grade of the CPMT 060208 insert is formulated as a primary choice for general machining of heat-resistant alloys, offering a balance of wear resistance and edge stability for consistent performance. Which holder types are compatible with this insert? Compatibility is governed by the insert’s form, clearance, tolerance class, fixing, size and thickness; the CPMT profile and the 06 size fit standard ISO CPMT holders that accept rhombic inserts with the specified thickness and hole geometry. What does the 0.8 mm corner radius mean for machining? A 0.8 mm corner radius increases edge strength and distributes cutting forces, improving tool life in interrupted cuts while producing a predictable edge profile on turned surfaces. How does the PVD coating benefit the cutting process? The PVD coating on the AH8015 grade reduces adhesion and thermal impact at the cutting edge, which helps to maintain edge integrity and extends usable tool life compared with uncoated grades. How can the insert be identified on delivery? Identification is by the ISO designation CPMT060208 and the grade AH8015; the item is listed under SKU 6951203-Tungaloy for ordering and inventory purposes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 AH8015 Wendeplatten - Tungaloy
Take advantage of the combination of PVD-coated carbide AH8015, a 0.8 mm corner radius and a precisely defined 11° clearance angle for consistent turning results and predictable tool life; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CPMT 060208 AH8015 – Turning insert (Tungaloy) The CPMT060208 AH8015 Tungaloy insert is an ISO‑standard rhombic turning insert designed for general machining of heat‑resistant alloys in external and internal turning applications. ISO rhombic turning insert CPMT060208 PVD-coated carbide grade AH8015 11° clearance angle, 0.8 mm corner radius Suitable for heat‑resistant alloys, single‑sided chipbreaker Engineered for efficient, predictable cutting performance The insert is manufactured from PVD‑coated carbide in grade AH8015, a combination engineered for a balanced performance between wear resistance and edge stability. The coating process produces a hard, thin surface layer that reduces abrasive wear and helps maintain cutting geometry at elevated temperatures. As a result, the tool offers consistent dimensional accuracy over longer tool life, which supports stable production runs and fewer index changes. The rhombic geometry with an included angle of 80° and a 0.8 mm corner radius provides a compromise between edge strength and finishing capability, making the insert suitable for a broad range of turning tasks. Geometry and chip control that reduce process risk Designed as an ISO‑normed insert with an 11° clearance angle, a thickness of 2.38 mm and a single‑sided chipbreaker, the cutting geometry aims to control chip formation and evacuation during medium to heavy cuts. The single‑sided chipbreaker helps to produce short, controllable chips where that is advantageous, or to direct chips away from the workpiece and toolholder. The combination of corner radius and chipbreaker contributes to improved surface quality and reduced vibration in interrupted cuts, which is particularly beneficial when machining heat‑resistant alloys that tend to generate higher cutting temperatures. Practical compatibility and workshop integration The indexable insert is supplied in the familiar ISO format, which simplifies mounting in compatible external holders or boring bars. Compatibility is defined by insert form, clearance angle, tolerance class, attachment method, size and thickness; a suitable clamping shim or set and replacement screws complete a robust system. Because the insert features a hole with a cylindrical bore and a one‑sided countersink (40°–60°), it fits holders designed for centrally fastened inserts and ensures secure seating under cutting loads. The system approach—insert, holder, shim/clamp set and fasteners—enables quick replacement and straightforward stock management in production environments. Clear selection for demanding materials and stable production This grade is recommended as a first choice for general machining of heat‑resistant alloys, offering a balanced response to thermal loading and abrasive conditions. The combination of a stable cutting edge and a wear‑resistant coating reduces the frequency of tool changes and supports consistent part quality, resulting in lower process variance and improved machine uptime. For shops focused on productivity and repeatability, the insert offers a technically sound solution that can be integrated into existing tool systems without complex adaptations. For reliable machining of heat‑resistant alloys, contact Metav Werkzeuge for tailored advice or order the Tungaloy CPMT060208 AH8015 insert via Metav Werkzeuge; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for fast assistance. Technical Data Article number: 6951174 SKU: 6951174-Tungaloy Manufacturer SKU: TUN6951174 Model series: ISO turning inserts Description: CPMT060208 AH8015 Tungaloy insert Facts Insert size: 06 Shape: rhombic, 80° included angle Corner radius: 0.8 mm Clearance angle: 11° Thickness: 2.38 mm Hole: with hole; cylindrical hole + one-sided countersink (40°–60°) Special features Material: PVD‑coated carbide (AH8015) Chipbreaker: single‑sided Application: turning; suitable for heat‑resistant alloys Compatibility: ISO‑standard insert – holder compatibility depends on form, angle, tolerance, attachment, size, thickness System components: insert, external holder or boring bar, shim/clamping set, replacement screws FAQ What materials is this insert best suited for? The CPMT060208 AH8015 insert is optimised for machining heat‑resistant alloys, offering a balance of wear resistance and edge stability for such materials. Which holders are compatible with the CPMT060208 geometry? Holders compatible with ISO‑normed rhombic inserts that accept a size 06 insert and a centrally fastened design (cylindrical hole with countersink) are suitable for this Tungaloy insert. How does the AH8015 grade affect tool life compared with uncoated carbide? The PVD coating on AH8015 reduces abrasive wear and improves edge retention at elevated temperatures, which typically extends usable tool life versus uncoated carbide under comparable conditions. What does the single‑sided chipbreaker provide in practical use? The single‑sided chipbreaker promotes consistent chip control and evacuation, reducing the risk of entanglement and improving surface finish in many turning operations. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CPMT 060208 AH8015 Wendeplatten - Tungaloy
Take advantage of the combination of wear-resistant PVD coating, stable AH8015 carbide grade and ISO compatibility for consistent turning performance and predictable tool life; order directly via Metav Werkzeuge or consult the team for application support. CPMT060208 AH8015 ISO turning insert for general-purpose turning — Tungaloy The CPMT060208 AH8015 is an ISO‑conforming rhombic turning insert designed for external and internal turning of heat‑resistant alloys in general machining applications PVD-coated carbide AH8015 for heat-resistant alloys ISO 060208 rhombic insert, 80° geometry Single-sided chipbreaker, cylindrical hole with countersink 0.8 mm nose radius and 2.38 mm plate thickness Consistent cutting performance for heat‑resistant alloys The PVD coating applied to this carbide grade delivers a balanced combination of wear resistance and edge stability, making it suitable for the machining of difficult, heat‑resistant alloys. The AH8015 grade is optimised for general‑purpose turning where a compromise between tool life and reliable edge strength is required. In practice, this means fewer insert changes and more predictable process windows when machining stainless or nickel‑based materials, contributing directly to improved component throughput and reduced downtime. Secure seating and broad holder compatibility reduce setup time Compatibility with toolholders is governed by the insert form, relief angle, tolerance class, fastening method, size and thickness. The rhombic shape with an 80° main angle and an 11° relief angle ensures a widely compatible geometry for standard ISO clamping systems. The insert’s cylindrical central hole with a 40°–60° one‑sided countersink allows secure fixing and repeatable location in a matching clamp or shim set. This mechanical reliability reduces rework from improper clamping and simplifies the selection of a matching external holder or boring bar in mixed production environments. Small radius and chip control for improved surface finish A 0.8 mm nose radius together with a single‑sided chipbreaker delivers controlled chip formation and a consistent surface texture on turned parts. The moderate nose radius helps achieve good surface quality without excessive cutting forces, while the chipbreaker directs swarf away from the cutting zone, aiding swarf evacuation and process stability. For shops processing component batches where surface finish and process repeatability matter, this insert affords an efficient balance between finish and productivity. Practical system benefits that support productive machining The insert forms part of a complete ISO turning system: the plate itself, a matching external holder or boring bar, and the appropriate shim/clamp set and replacement screws. The 2.38 mm plate thickness enhances stiffness at the cutting edge and contributes to vibration dampening during interrupted cuts. Together with the ISO 060208 format, these attributes simplify tool management on the shop floor and help standardise tooling across similar turning tasks, supporting lean tooling inventories and quicker tool changeovers. Choose the Tungaloy AH8015 grade for reliable turning of heat‑resistant alloys and contact Metav Werkzeuge for availability and application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6951142 SKU: 6951142-Tungaloy Manufacturer SKU: TUN6951142 Model series: ISO-Drehwendeschneidplatten WPL designation: CPMT060208 Facts Geometry angle: 80° Relief angle: 11° Nose radius: 0.8 mm Plate thickness: 2.38 mm Plate size: 06 ISO code: 060208 Design and application Material: carbide Coating: PVD Grade: AH8015 Chipbreaker: single-sided Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Plate shape: rhombic Application: turning Typical uses: external and internal turning System composition: ISO insert, matching external holder or boring bar, shim/clamp set and replacement screws FAQ What materials is this insert best suited for? The insert in AH8015 grade with PVD coating is intended for machining heat‑resistant alloys; its balanced wear resistance and edge stability make it suitable for stainless and nickel‑based materials as well as other demanding steels. How does the insert locate in the holder? Clamping relies on the rhombic form, the central cylindrical hole with a one‑sided countersink and the ISO geometry; correct matching of holder form, tolerance class and clamping set ensures repeatable location. Can this insert be used for both roughing and finishing? Yes, the combination of a 0.8 mm nose radius and a single‑sided chipbreaker provides sufficient versatility for both light finishing passes and more aggressive material removal, depending on cut parameters and holder rigidity. Which system components are required to fit the insert? A compatible external holder or boring bar, a suitable shim/clamp set and the correct replacement screws are required to assemble the ISO turning system for secure and repeatable operation. What distinguishes AH8015 from other grades? AH8015 is a PVD‑coated carbide grade optimised for a balance between edge strength and wear resistance, making it a first choice for general machining of heat‑resistant alloys where consistent tool life is important. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 NS9530 Wendeplatten - Tungaloy
High surface quality and low cutting forces make this insert ideal for precision finishing in external and internal turning; its ISO compatibility simplifies toolholder selection. Benefit from the NS9530 uncoated cermet grade and the stable 80° rhombic geometry — order the insert directly via Metav Werkzeuge or consult our specialists for application support. CPMT 060208 NS9530 CPMT turning insert by Tungaloy — uncoated cermet, 80° rhombic A CPMT 060208 NS9530 indexable insert designed for precision external and internal turning, optimised for finishing cuts on steel and continuous cutting conditions CPMT 060208 geometry, 80° rhombic NS9530 uncoated cermet for finishing Sharp edge for low cutting forces Compatible with ISO turning holders Reliable finishing performance for steel components The NS9530 uncoated cermet grade is formulated to deliver a sharp cutting edge and consistently high surface finish when machining steel. As a finishing grade, the material reduces cutting forces and helps preserve dimensional accuracy during light cuts and continuous feed conditions. This results in lower burr formation and reduced need for secondary finishing, improving process efficiency and part quality. The performance is particularly evident when small depths of cut are applied, where the combination of edge geometry and substrate hardness delivers repeatable results. Geometry and dimensions that support consistent tool life The rhombic 80° geometry with a 0.8 mm corner radius and 11° clearance balances strength and finesse for finishing operations. The 2.38 mm plate thickness and the ISO CPMT form ensure mechanical stability in suitable holders, while the cylindrical hole with single-side countersink (40°–60°) secures repeatable clamping and orientation. These dimensions reduce vibration and support steady chip evacuation with the one-sided chipbreaker, translating into more reliable tool life and uniform surface integrity across production batches. System integration and practical selection guidance Installed as part of a standard ISO turning system, the insert pairs with appropriate external holders or boring bars, a matching shim/clamp set and replacement screws to complete the cutting system. Selection should consider workpiece material, required finish and machine stability; the one-sided chipbreaker and uncoated cermet backing make this insert particularly suitable for continuous turning of steel where minimal cutting forces and excellent finishes are priorities. For mixed production runs, pairing this finishing grade with a complementary roughing grade supports a productive machining sequence and simplified inventory. For detailed application advice on Tungaloy NS9530 finishing inserts or to discuss batch availability with Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored assistance. Technical data Article number: 6951143 Manufacturer SKU: TUN6951143 SKU: 6951143-Tungaloy ISO designation: CPMT060208 Grade: NS9530 Manufacturer: Tungaloy Dimensions & core data Corner radius: 0.8 mm Plate size: 06 Thickness: 2.38 mm Clearance angle: 11° Included angle: 80° Hole: cylindrical hole + single-side countersink (40°–60°) Materials & features Material: Cemented carbide Cutting material type: uncoated cermet NS9530 Chipbreaker: one-sided Application: Turning (external and internal) Plate form: rhombic Model series: ISO turning indexable inserts FAQ Which materials is this insert intended for? The CPMT 060208 NS9530 insert is designed primarily for steel finishing operations; the NS9530 uncoated cermet backing prioritises low cutting forces and excellent surface finish when machining steel components. Can this insert be used for both external and internal turning? Yes, the ISO rhombic form and the secure clamping provided by the cylindrical hole with countersink make the insert suitable for both external and internal turning tasks within appropriate holder systems. How does the NS9530 grade affect process stability? The NS9530 grade offers a sharp cutting edge and reduced cutting forces; in combination with the 80° geometry and one-sided chipbreaker, this supports stable cutting behaviour and consistent surface quality under continuous feed conditions. What holder compatibility factors must be checked? Compatibility depends on ISO form, clearance angle, tolerance class, clamping method, plate size and thickness; the CPMT 060208 form and 2.38 mm thickness must match the intended ISO turning holder or boring bar. What are the distinguishing geometry features to note? Key geometry features include the 80° rhombic shape, 0.8 mm corner radius, 11° clearance angle and the cylindrical hole with single-side countersink (40°–60°), all contributing to secure clamping and smooth finishing performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 NS9530 Wendeplatten - Tungaloy
Benefit from precise finishing, low cutting forces and ISO compatibility to keep turning processes consistent and productive. Order the CPMT 060208 NS9530 turning inserts via Metav Werkzeuge or consult technical advisers for application-specific recommendations. CPMT 060208 NS9530 – Tungaloy ISO turning insert for finishing applications A CPMT 060208 NS9530 turning insert engineered for finishing cuts on steel, offering a sharp cutting edge and reliable chip control. ISO-format rhombic insert 06 size Sharp cermet grade NS9530 for fine finishing Single-sided chipbreaker for continuous cuts 11° relief angle, 0.8 mm corner radius Consistent, high-quality surface finish for steel components The uncoated cermet grade NS9530 is designed specifically for finish turning of steel, delivering low cutting forces and an excellent surface quality. The fine-grain composition ensures a sharp edge that resists built-up edge during continuous cuts, which translates into fewer reworks and more predictable part quality. With an included angle of 80° and a 0.8 mm corner radius, the insert supports delicate finishing passes while preserving edge integrity for form and profile turning. Stable chip control and productivity in light-depth operations A single-sided chipbreaker combined with the sharp cermet substrate provides controlled chip formation under small depths of cut, minimising interruptions and enabling steady cycle times for repetitive finishing tasks. The grade’s low-friction contact with the workpiece reduces heat generation and wear, extending tool life in continuous-feed applications. This balance of performance and economy supports higher uptime and reliable surface outcomes when machining longer runs. Secure mounting and ISO compatibility for straightforward tool management The ISO-format rhombic geometry and standard hole arrangement mean the insert fits common external holders and boring bars that accept ISO indexable turning inserts. The central hole with a cylindrical bore and one-sided countersink (40°–60°) ensures positive clamping and repeatable seating, simplifying tool changes and inventory management. A thickness of 2.38 mm and the specified tolerance class make replacement and indexing straightforward within established tool systems. Technical clarity for informed tooling decisions Key machining parameters such as relief angle (11°), corner radius (0.8 mm) and the finishing-focused uncoated cermet composition should guide selection for thin or interrupted cuts on steels. The finishing grade prioritises surface integrity over roughing removal rates; therefore, optimising feed and speed for fine passes will maximise component quality and insert life. For uncertain applications, matching the chipbreaker and grade to material, machining stability and desired surface finish yields the best results. For precision finishing with Tungaloy NS9530 inserts, contact Metav Werkzeuge for specification support and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6951175 SKU: 6951175-Tungaloy Manufacturer SKU: TUN6951175 Model series: ISO indexable turning inserts Facts Insert designation: CPMT060208 Insert size: 06 Thickness: 2.38 mm Included angle: 80° Relief (free) angle: 11° Corner radius: 0.8 mm Special features Grade: uncoated cermet NS9530 Chipbreaker: single-sided Shape: rhombic Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Application: turning, finish cutting on steel FAQ What materials is this insert suitable for? The uncoated cermet NS9530 is optimised for finishing on steel and performs best in continuous cutting and small depth-of-cut operations with stable machining conditions. Is the CPMT 060208 compatible with standard ISO holders? Yes, the CPMT060208 is an ISO-format rhombic insert designed for compatibility with external holders and boring bars that accept ISO indexable turning inserts; the central hole and countersink enable secure clamping. Which aspects of surface finish does the NS9530 grade improve? The NS9530 cermet offers a sharp cutting edge and reduced built-up edge, resulting in finer surface quality and consistent part finish when used for finish turning. How does the single-sided chipbreaker affect machining? The single-sided chipbreaker on this insert promotes predictable chip control during continuous cuts, helping to maintain steady cycle times and reducing the risk of chip-related interruptions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 NS9530 Wendeplatten - Tungaloy
Data inconsistency detected: the product is described as 'carbide' in one place while the cutting grade is specified as an 'uncoated cermet' (NS9530). These material descriptions contradict one another, which could lead to confusion or errors in understanding the product's properties, performance, or intended applications. It is crucial to resolve this discrepancy to ensure accurate communication of the product's characteristics, as well as to maintain consistency across technical documentation and marketing materials. Please confirm the correct material specification, whether it is indeed carbide, uncoated cermet, or another material entirely, before a full and accurate product description can be produced and finalised.
CPMT 060208 T5115 Wendeplatten - Tungaloy
Take advantage of the combination of a CVD-coated carbide grade (T5115), a 0.8 mm corner radius and ISO-standard geometry to achieve stable, predictable turning results in cast iron. Order genuine Tungaloy inserts directly via Metav Werkzeuge or consult the specialists for grade and chipbreaker selection. CPMT060208 T5115 — ISO indexable turning insert, CVD-coated carbide by Tungaloy A CPMT060208 T5115 indexable insert engineered for turning applications, offering balanced wear resistance and edge stability for cast iron machining. ISO 80° rhombic geometry CVD-coated carbide T5115 Single-sided chipbreaker design Cylindrical hole with 40°–60° countersink Precise chip control for reliable cast iron turning The insert is designed to deliver consistent chip formation when machining cast iron, thanks to the CVD-coated carbide combination and the T5115 grade, which balances wear resistance with edge stability. The single-sided chipbreaker is optimised for common turning operations, so chip evacuation is improved and cutting forces remain stable. This leads to fewer unplanned tool changes and reduced cycle-time variability. The coating’s function is to protect the cutting edge at elevated temperatures and abrasion, which in turn supports longer periods of uninterrupted production. Secure seating and geometry that support process stability Compatibility with clamping systems is governed by geometry — form, relief angle, tolerance class, fixing, size and thickness — which is why the insert follows ISO-standard dimensions. The 80° rhombic shape provides versatile orientation options for both external and internal turning tasks and helps distribute cutting loads evenly. A cylindrical hole combined with a one-sided countersink ensures positive locating and repeatable clamping. The specified 11° relief angle and corner radius 0.8 mm enable a controlled transition between roughing and finishing, reducing vibration and supporting consistent surface finish. Predictable tool life and practical handling in production With a plate thickness of 2.38 mm and the single-sided chipbreaker, the insert offers a predictable wear curve that simplifies inventory planning and tool-change scheduling. The universal characteristics of the grade make it suitable for many cast iron grades; matching the chipbreaker and ISO geometry to workpiece stability and machining strategy will pay off in reduced scrap and higher throughput. The design supports economical stockkeeping by allowing one insert style to cover a range of operations, while the robust CVD-coated carbide substrate contributes to reliable, repeatable performance across batches. For tailored grade selection or to procure genuine Tungaloy CPMT060208 T5115 indexable inserts, contact Metav Werkzeuge — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 for prompt application advice and ordering support. Technical Data Article number: 6864677 SKU: 6864677-Tungaloy Manufacturer SKU: TUN6864677 Name: CPMT060208 T5115 Tungaloy insert Facts ISO code: 060208 Geometry angle: 80° Corner radius: 0.8 mm Relief angle: 11° Thickness: 2.38 mm Special features Shape: Rhombic Hole: With cylindrical hole + one-sided countersink (40°–60°) Coating/grade: T5115, CVD-coated carbide Chipbreaker: Single-sided Application: Turning, suitable for cast iron FAQ Which materials is this insert best suited for? The CPMT060208 T5115 insert is formulated for cast iron machining; the T5115 grade and CVD-coated carbide combine wear resistance with edge stability for consistent results. How does the geometry affect holder compatibility? Compatibility depends on form, relief angle, tolerance class, fixing, size and thickness; the ISO-standard CPMT060208 geometry ensures repeatable seating in compliant holders. What is the benefit of the 0.8 mm corner radius? A 0.8 mm corner radius offers a balanced compromise between edge strength and surface finish, allowing stable cutting on varied turning operations without excessive cutting forces. What does the cylindrical hole with countersink provide? The cylindrical hole plus one-sided countersink (40°–60°) enables positive locating and secure clamping, which supports repeatable tool positioning and reduced assembly variation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of robust CVD-coated carbide, precise ISO geometry and straightforward holder compatibility for consistent turning performance and low downtime. Order the CPMT060208 T6215 insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. CPMT 060208 T6215 – ISO turning insert by Tungaloy CPMT060208 T6215 is an ISO-format rhombic turning insert designed for stable to lightly interrupted turning operations, particularly on stainless steels. CVD-coated carbide grade T6215 For turning of stainless steels 11° clearance angle, rhombic 80° shape One-sided chipbreaker, hole with countersink Corner radius 0.8 mm, thickness 2.38 mm Reliable wear resistance for continuous production The CVD-coated carbide composition of this insert (grade T6215) provides elevated wear resistance and consistent edge retention when machining stainless steel under steady or lightly interrupted conditions. CVD coating enhances surface hardness and thermal stability, which translates into longer cutting life and fewer insert changes during production runs. For operations where repeatability and predictable tool life are priorities, this turning insert reduces unplanned downtime and contributes to a smoother production flow. Geometry that ensures repeatable clamping and predictable cuts The insert’s ISO rhombic 80° geometry, combined with an 11° clearance angle and a 0.8 mm corner radius, offers a balance between cutting-edge strength and surface finish. The presence of a cylindrical hole with a single‑sided countersink (40°–60°) ensures secure fastening in standard ISO holders; compatibility is determined by form, clearance, tolerance class, fastening, size and thickness. Clear, standardised geometry simplifies tool changeover and makes the insert straightforward to integrate into existing tool systems, improving process reliability. Chip control and practical application guidance A one-sided chipbreaker is optimised for chip formation when turning ductile or work‑hardening materials such as stainless steel, promoting controlled chips and safer swarf evacuation. The insert is intended for both external and internal turning; select a matching external holder or boring bar, a suitable clamp or clamping set and spare screws to complete the system. Because the grade and chipbreaker are designed for stable to lightly interrupted cuts, maintain consistent setup rigidity and check cutting parameters against material characteristics to achieve the best balance of productivity and surface quality. For precise tool selection and integration of the Tungaloy CPMT060208 T6215 insert into existing turning systems, contact Metav Werkzeuge for tailored advice and ordering — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application suitability and compatible holders. Technical data Article number: 6903094 SKU: 6903094-Tungaloy Manufacturer SKU: TUN6903094 Model series: ISO turning inserts ISO designation: 060208 Grade / sort: T6215 Material: carbide Shape: rhombic (80°) Size: 06 Thickness: 2.38 mm Clearance angle: 11° Corner radius: 0.8 mm Hole style: cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: one-sided Application: turning Facts Thickness: 2.38 mm Radius: 0.8 mm Clearance angle: 11° ISO code: 060208 Article number: 6903094 Special features CVD-coated carbide (grade T6215) Designed for stainless steels under stable to lightly interrupted conditions Compatible with ISO holders when form, tolerance and fastening match System components: insert + appropriate holder or boring bar + clamping set + spare screws FAQ Which materials is this insert suitable for? The CPMT060208 T6215 insert from Tungaloy is optimised for machining stainless steels; the CVD-coated carbide grade T6215 offers wear resistance and thermal stability for stable to lightly interrupted turning tasks. How can compatibility with holders be checked? Compatibility depends on the insert form, clearance angle, tolerance class, fastening type, size and thickness; the ISO-format CPMT060208 is designed to fit standard ISO rhombic holders when these parameters match. What advantage does the one-sided chipbreaker provide? The one-sided chipbreaker on this indexable insert helps control chip shape and evacuation during turning, reducing the risk of snarled swarf and improving process safety and surface finish. When is the 0.8 mm corner radius recommended? A 0.8 mm corner radius balances edge strength and surface finish, making it suitable for general finishing and semi-finishing of stainless steel components where a robust cutting edge is required. Is this insert suitable for interrupted cuts? The Tungaloy grade T6215 is intended for stable to lightly interrupted conditions; for heavily interrupted cuts, review the application demands and consider a geometry or grade specifically rated for severe interruptions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of a wear‑resistant T6215 grade, precise 80° rhombic geometry and reliable clamping features for consistent turning performance — order directly via Metav Werkzeuge or request advice from our consultants. CPMT 060208 T6215 indexable insert for turning by Tungaloy — rhombic 80° geometry, CVD-coated carbide CPMT 060208 T6215 is an ISO‑standard indexable insert designed for external and internal turning applications, optimised for rostfreier Stahl under stable to slightly interrupted cutting conditions and compatible with ISO turning holders. CVD-coated carbide grade T6215 80° rhombic geometry for stable cutting Designed for turning rostfreier Stahl Cylindrical hole with single countersink Longer tool life and consistent cutting with CVD coating The CVD-coated carbide composition of this insert provides a wear‑resistant cutting edge suited to sustained production runs. The coating reduces adhesive wear and extends edge life when machining rostfreier Stahl, lowering the need for frequent insert changes. By choosing a T6215 grade, the combination of substrate and coating offers a balance between toughness and hardness, supporting repeatable surface quality and reduced downtime through fewer interventions. Geometry that improves chip control and stability The 80° rhombic geometry and the corner radius 0.8 mm contribute to a positive cutting action and controlled chip formation. The single‑sided chipbreaker is matched to the grade to help fragment chips reliably during continuous and slightly interrupted cuts. This geometry also increases edge support in the holder, offering improved stability when turning components where dimensional consistency matters, such as shafts or precision cylindrical parts. Practical compatibility and secure clamping for reliable use Designed to ISO standards, the insert fits a wide range of ISO turning holders when form, relief angle, tolerance class, fixings, size and thickness correspond. The insert features a cylindrical hole with a single‑sided countersink (40°–60°) for secure clamping and straightforward replacement, reducing set‑up time and ensuring repeatable seat positioning. The nominal thickness of 2.38 mm and the ISO size designation simplify selection for standard turning tool systems. Application guidance for productivity and process security Selecting this insert for machining rostfreier Stahl under stable conditions delivers good edge life and predictable results. The T6215 grade is optimised to maintain a stable cutting edge and broad material coverage in practical workshop scenarios, making it suitable for batch production or single‑piece precision work. Where cutting conditions become heavily interrupted or highly abrasive, consider adapting cutting data or insert geometry to preserve tool life and part quality. For a tailored recommendation based on specific workpiece material or holder compatibility, please contact Metav Werkzeuge — Metav Werkzeuge can advise on clamping options and supply original Tungaloy inserts for immediate use. Technical data Article number: 6951200 Manufacturer SKU: TUN6951200 SKU: 6951200-Tungaloy Model series: ISO-Drehwendeschneidplatten Designation: CPMT060208 Facts ISO code: 060208 Insert size: 06 Thickness: 2.38 mm Relief angle: 11° Corner radius: 0.8 mm Insert angle: 80° Special features Material: carbide Coating: CVD Grade: T6215 Shape: rhombic 80° Hole: with hole Hole style: cylindrical hole with single‑sided countersink (40°–60°) Chipbreaker: one‑sided Application: turning Suitable for: rostfreier Stahl FAQ What materials is this insert best suited for? The CPMT 060208 T6215 insert is formulated for machining rostfreier Stahl and offers a balanced combination of wear resistance and edge stability for such alloys. Which holders are compatible with this ISO insert? Compatibility depends on the holder form, relief angle, tolerance class, fastening method, size and thickness; the CPMT 060208 conforms to ISO standards to ensure fitment with matching ISO turning holders. How does the T6215 grade affect tool life? The T6215 CVD coating and carbide substrate enhance wear resistance, providing longer edge life under stable cutting conditions compared with uncoated grades. Is the insert suitable for interrupted cuts? The insert performs well under stable to slightly interrupted conditions; for heavy interruptions, toolpath and cutting data adjustments are recommended to maintain edge integrity. Are replacement screws and underplates required for mounting? Standard practice is to use the matching underlay/clamping set and fastening hardware specified for the holder system; secure seating is ensured by the cylindrical hole and countersink design. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CPMT 060208 T6215 Wendeplatten - Tungaloy
High wear resistance from the CVD-coated carbide T6215, combined with a precise 0.8 mm corner radius and 11° relief, ensures stable turning of rostfreier Stahl with long tool life and consistent surface quality — order the insert directly via Metav Werkzeuge or contact our consultants for application advice. CPMT 060208 T6215 ISO rhombic insert for turning by Tungaloy — 11° relief, 0.8 mm radius CPMT 060208 T6215 is an ISO-standard rhombic turning insert designed for external and internal turning operations, optimised for rostfreier Stahl under stable to lightly interrupted cutting conditions CVD-coated carbide for high wear resistance Designed for rostfreier Stahl turning Rhombic ISO insert, 11° relief angle 0.8 mm corner radius, single-sided chipbreaker Longer tool life through CVD-coated carbide and tailored grade The combination of a CVD-coated carbide substrate and the T6215 grade delivers a wear-resistant cutting edge that maintains geometry over extended cycles. This results in fewer insert changes and more predictable tool life, which reduces downtime and contributes to a more economical process. The hard-wearing coating also supports consistent surface finish in serial production, making the insert suitable for shops that prioritise throughput and repeatability. Geometry engineered for stable chips and reliable surface quality The rhombic ISO insert form, paired with a single-sided chipbreaker, controls chip flow and minimises vibration during turning. The 11° relief angle and 0.8 mm corner radius provide a balance between edge strength and dimensional accuracy, enabling secure finishes on shafts and bores. For less experienced readers: a larger corner radius increases edge robustness and improves surface finish, while the relief angle reduces rubbing behind the cutting edge to avoid excessive heat generation. Practical compatibility and straightforward integration into holders Compliance with ISO dimensions ensures that the insert mates with compatible holders; compatibility depends on form, relief angle, tolerance class, fastening, size and thickness. The insert comes with a cylindrical hole and a single-side countersink (40°–60°) for secure fastening and repeatable seating. With a plate thickness of 2.38 mm and standard size designation 06, the component integrates into common turning tool systems and supports routine replacement without special adapters. For production-tested reliability with the T6215 wear grade, contact Metav Werkzeuge for availability and technician-led application support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6951172 Manufacturer SKU: TUN6951172 Model series: ISO-Drehwendeschneidplatten Material: Carbide Coating / Grade: T6215 (CVD-coated) Core technical data Corner radius: 0.8 mm Plate thickness: 2.38 mm Relief angle: 11° Insert size: 06 Included angle: 80° Special features Rhombic plate form With hole: cylindrical hole + single-side countersink (40°–60°) Single-sided chipbreaker ISO-standard turning insert Suited for turning rostfreier Stahl under stable to lightly interrupted conditions FAQ What materials is this insert suitable for? The Tungaloy CPMT 060208 T6215 insert is designed primarily for rostfreier Stahl and offers good wear resistance for that material class. How does the chipbreaker affect machining? The single-sided chipbreaker on this insert improves chip control in turning operations, helping the tool maintain stable cutting and consistent surface quality. Which holders are compatible with this ISO insert? Compatibility is determined by form, relief angle, tolerance class, fastening, size and thickness; the ISO format of the CPMT 060208 supports standard external and internal turning holders. What does the T6215 designation indicate? T6215 denotes a CVD-coated carbide grade optimised for wear resistance and stable cutting when machining rostfreier Stahl. How does the 0.8 mm corner radius influence performance? A 0.8 mm corner radius increases edge strength and helps achieve robust surface finishes, while balancing cutting forces for dimensional stability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T6215 Wendeplatten - Tungaloy
Take advantage of the combination of durable CVD-coated carbide, precise ISO geometry and a secure clamping design to improve productivity and surface finish in stainless steel turning. The robust cutting grade T6215 and the rhombic 06 form ensure dependable performance under stable to slightly interrupted cuts — order the insert directly via Metav Werkzeuge or consult the technical team for application matching. CPMT060208 T6215 — Turning insert CPMT 060208 for turning by Tungaloy The CPMT060208 T6215 is an ISO-standard turning insert designed for reliable external and internal turning of stainless steels under stable to lightly interrupted conditions CVD-coated carbide for high wear resistance Rhombic insert shape (06) for versatile turning 11° clearance angle for stable cutting Central hole with 40°–60° countersink for secure clamp Longer tool life where stainless steels challenge productivity The CVD-coated carbide composition of this ISO turning insert delivers a wear-resistant cutting edge engineered for the demands of machining stainless steel. The selected grade, identified as T6215, balances toughness and hardness to resist abrasive wear while preserving edge integrity during extended cycles. This results in fewer changeovers and more consistent component quality, making the insert a rational choice when process efficiency and predictable tool life are priorities. Geometry and clamping designed for repeatability and surface finish The rhombic 06 form combined with a corner radius of 0.8 mm and an 11° clearance angle provides a stable cutting geometry that supports fine surface finishes and dimensional control. The single-sided chipbreaker is matched to the grade for controlled chip formation when turning stainless steels, reducing vibration and improving tool life. The central hole with a 40°–60° countersink ensures positive seating and repeatable clamping in compatible holders, minimising runout and set-up time. System compatibility and application guidance for shop-floor reliability Supplied as part of the ISO turning insert series, the component is intended for use in a complete system: ISO insert, suitable external holder or boring bar, support pad/clamping kit and replacement screws. Compatibility depends on insert form, relief angle, tolerance class, fixation type, size and thickness; observe these parameters when selecting a holder to secure consistent performance. The 2.38 mm plate thickness and rhombic shape make the insert adaptable across common turning operations where stainless steels are encountered, helping to reduce cycle time and support sustained production runs. Contact Metav Werkzeuge for tailored application advice on the Tungaloy CPMT060208 T6215 insert and specify SKU TUN6951139 when enquiring — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6951139 SKU: 6951139-Tungaloy Manufacturer SKU: TUN6951139 Brand: Tungaloy Model series: ISO turning indexable inserts Application: Turning Facts Corner radius: 0.8 mm Plate thickness: 2.38 mm Clearance angle: 11° ISO designation: CPMT060208 Insert size: 06 Insert included hole style: central hole with one-sided countersink (40°–60°) Included angle: 80° Special features CVD-coated carbide grade T6215 Rhombic 06 insert form Single-sided chipbreaker Central hole with cylindrical bore and countersink Suitable for stable to slightly interrupted cuts in stainless steel ISO-standardised geometry for holder compatibility FAQ What materials is the CPMT060208 T6215 optimised for? The CPMT060208 T6215 insert is optimised for machining stainless steel; the CVD-coated carbide grade provides wear resistance suited to this material group. Can the insert handle interrupted cuts? The T6215 grade and the insert geometry permit stable to lightly interrupted cuts; heavy interruptions may require a different grade or a more robust cutting strategy. What is the exact corner radius and why does it matter? This indexable insert has a 0.8 mm corner radius, which helps balance cutting-edge strength and surface finish—larger radii increase edge strength, while smaller radii favour finer finishes. Which clamping arrangement is required for secure seating? A holder that matches the rhombic CPMT form with a central screw and a countersink matching 40°–60° is required to ensure correct seating and repeatability. What is the SKU and manufacturer article number for ordering? Order using SKU 6951139-Tungaloy or the manufacturer article number 6951139; the manufacturer SKU is TUN6951139. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9215 Wendeplatten - Tungaloy
Take advantage of high wear resistance, stable chip control and a geometry optimised for productive turning to maintain consistent cycle times. Order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. CPMT 060208 T9215 ISO turning insert — rhombic, CVD-coated, 11° relief (Tungaloy) The CPMT060208 T9215 is an ISO‑standard rhombic indexable insert designed for external and internal turning in medium‑grade steel, offering a balanced combination of wear resistance and fracture toughness for continuous to lightly interrupted cuts ISO‑standard rhombic turning insert CVD‑coated cemented carbide grade T9215 One‑sided chipbreaker for medium steel 0.8 mm corner radius, 11° relief High productivity through material and grade selection The combination of a CVD‑coated cemented carbide substrate and the T9215 grade delivers reliable performance in medium steel machining. The coating increases wear resistance, while the substrate keeps the cutting edge stable under load, which results in predictable tool life and fewer insert changes. For production environments where uptime and repeatability matter, this grade supports sustained cutting speeds and stable surface finishes without compromising edge integrity. Compatibility and system integration for safe clamping Designed to ISO plate dimensions, the insert integrates into common external holders and boring bars where form, relief angle, tolerance class, fixing method, size and thickness match the holder geometry. The central cylindrical hole with a single‑side countersink (40°–60°) ensures secure seating and simple fastening with standard clamping sets and replacement screws; a correctly chosen shim or clamp reduces vibration, improves chip control and extends service intervals. Practical machining benefits and parameter guidance With an 11° relief angle and an 80° cutting edge orientation, the geometry helps maintain cutting force direction and radial stability during turning. The 0.8 mm corner radius offers an effective balance between edge strength and surface finish; choose this radius for general finishing to semi‑roughing operations in medium steel. The one‑sided chipbreaker is tuned for continuous to slightly interrupted cuts—select feed and depth of cut accordingly to avoid overloads and to exploit the grade's fracture resistance. Ease of selection and reduced process risk Using an ISO‑coded insert simplifies procurement and tool inventory while enabling quick identification of compatible holders. The plate size code and standardised hole style reduce the risk of mismatched assemblies. Where process safety and consistent part quality are priorities, this insert supports stable chip formation and predictable wear patterns, contributing to fewer unscheduled stops and more consistent throughput. For application advice or to secure original Tungaloy inserts for your production, contact Metav Werkzeuge — specialists are available to recommend the optimal holder and machining parameters for this grade and geometry Technical data Article number: 6951133 Manufacturer SKU: TUN6951133 SKU: 6951133-Tungaloy Manufacturer: Tungaloy Facts ISO designation: 060208 Plate size: 06 Plate thickness: 2.38 mm Corner radius: 0.8 mm Relief angle: 11° Cutting edge angle: 80° Special features Shape: rhombic Hole: cylindrical hole with single‑side countersink (40°–60°) Chipbreaker: one‑sided Grade/coating: T9215, CVD‑coated cemented carbide Intended application: turning, external and internal Typical system: insert, appropriate external holder or boring bar, shim/clamp set and replacement screws FAQ What materials is this insert best suited for? The CPMT060208 T9215 insert is optimised for medium‑grade steel machining; the CVD coating and T9215 grade combine wear resistance with edge toughness for continuous to lightly interrupted cuts. Is the insert compatible with standard ISO clamping systems? Yes, the insert follows ISO plate dimensions (060208) and features a central cylindrical hole with a single‑side countersink, allowing mounting in holders and boring bars that match the form, size and tolerance class. What cutting geometry gives the best surface finish? The combination of an 11° relief, 80° cutting edge orientation and a 0.8 mm corner radius provides a stable cutting condition that yields consistent surface quality in finishing and semi‑finishing operations. Can this grade handle light interruption such as workpiece irregularities? The T9215 grade is designed with fracture resistance in mind, making it suitable for continuous to slightly interrupted cuts; however, for heavy interruptions a more robust geometry or different grade may be preferable. How should chip control be optimised with this insert? Use the one‑sided chipbreaker together with appropriate feeds and depths of cut for medium steel. Secure clamping and the correct holder alignment reduce vibration and help achieve consistent chip formation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9215 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, fracture toughness and precise geometry for reliable production results; the CVD-coated grade T9215 enables productive turning of medium-strength steel with continuous to slightly interrupted cuts. Order the CPMT060208 T9215 turning insert directly via Metav Werkzeuge or request consultancy for process optimisation. CPMT060208 T9215 — ISO turning indexable insert for medium steel, rhombic 80° CPMT060208 T9215 is an ISO-conform rhombic turning insert designed for external and internal turning in medium-strength steel, combining a CVD-coated carbide grade with an optimised single-sided chipformer. CVD-coated carbide grade T9215 Optimised for medium steel machining Rhombic 80° insert, 0.8 mm corner radius Cylindrical hole with single-side countersink Productivity and wear resistance for medium steel turning The CVD-coated T9215 grade provides a balanced combination of wear resistance and fracture toughness, making it well suited for sustained production. The coating reduces abrasive wear and heat impact during longer runs, so machining cycles remain consistent even under elevated cutting speeds. For shops aiming to raise throughput, the combination of a robust substrate and protective CVD coating supports longer tool life and stable component quality, especially in continuous to lightly interrupted cutting conditions. Reliable chip control and surface quality The single-sided chipbreaker and 80° rhombic geometry deliver reliable chip formation and evacuation, which helps maintain a consistent surface finish on turned components. A 0.8 mm corner radius strikes a compromise between edge strength and the ability to achieve fine contours; an 11° clearance angle supports cutting stability by reducing flank contact. Together these features reduce process variation and simplify parameter setting when switching between similar turning tasks. Compatibility, mounting and application guidance Compatibility with clamping systems depends on insert shape, clearance angle, tolerance class, clamping style, size and thickness; the insert is supplied with a cylindrical hole and a single-side countersink (40°–60°) to match standard ISO rotatable-holding systems. The ISO designation aids in selecting the correct holder and underlay set. For selection support, Metav Werkzeuge can advise on the holder match, clamping torque and suitable cutting parameters to achieve the intended productivity while protecting the cutting edge. For tailored advice on integrating the Tungaloy CPMT060208 T9215 into production and prompt supply via Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 6951197 Manufacturer SKU: TUN6951197 Brand: Tungaloy Model series: ISO turning indexable inserts Facts Corner radius: 0.8 mm Clearance angle: 11° Plate thickness: 2.38 mm Main angle: 80° Special features Grade: T9215 CVD-coated carbide Rhombic plate form, size 06 One-sided chipbreaker With cylindrical hole and single-side countersink (40°–60°) ISO designation: CPMT060208 Suitable application: turning (external and internal) Compatibility depends on form, clearance, tolerance, clamping, size and thickness FAQ What materials is this insert best suited for? The CPMT060208 T9215 insert is primarily specified for medium-strength steel and performs well in continuous to lightly interrupted turning where the T9215 grade provides balanced wear resistance and toughness. How does the chipbreaker influence machining? The single-sided chipbreaker on this indexable insert supports consistent chip formation and evacuation, improving surface finish and reducing the risk of chip-related interruptions during machining. What holder characteristics are required for correct mounting? Correct mounting requires a holder that matches the rhombic shape, 80° main angle, 11° clearance and the plate thickness; the cylindrical hole with countersink must align with the clamping screw and underlay used. Is this insert suitable for interrupted cuts? The CVD-coated carbide grade is designed for continuous to slightly interrupted cuts; for heavily interrupted operations, a grade with higher fracture resistance may be preferred. What is the manufacturer article number and how can it be referenced? The manufacturer article number is 6951197 and the manufacturer SKU is TUN6951197; citing these identifiers ensures accurate procurement and traceability. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9215 Wendeplatten - Tungaloy
The combination of CVD-coated cemented carbide in grade T9215, a 0.8 mm corner radius and ISO compatibility delivers high wear resistance with reliable edge stability for productive medium-steel turning; order the CPMT060208 T9215 directly via Metav Werkzeuge or ask the consultants for application advice CPMT 060208 T9215 CPMT060208 Tungaloy turning insert for Drehen A CPMT060208 T9215 indexable turning insert designed for medium-steel external and internal turning, offering robust wear resistance and consistent performance in continuous to slightly interrupted cuts CVD-coated cemented carbide grade T9215 Rhombic ISO form CPMT 06 for versatile turning 0.8 mm corner radius for stable edge strength Cylindrical hole with single-sided countersink Reliable performance for medium-steel turning The CPMT060208 T9215 indexable insert combines a CVD-coated cemented carbide substrate with a geometry engineered for balance between wear resistance and fracture toughness. This makes the insert particularly suited to medium-steel machining where consistent tool life and predictable results are essential. The one-sided chipbreaker promotes controlled chip formation, reducing heat concentration at the cutting edge and enabling stable material removal during both continuous and slightly interrupted cutting cycles. Dimensional and mounting benefits that reduce downtime With a 0.8 mm corner radius, 2.38 mm thickness and an 11° clearance, the insert provides a reliable cutting edge that tolerates moderate feed and depth of cut without premature edge failure. The cylindrical hole with a 40°–60° single-sided countersink ensures secure clamping in compatible holders; compatibility depends on holder form, clearance angle, tolerance class, fastening method, size and thickness. Using correctly matched clamping sets and replacement screws reduces setup time and helps maintain process repeatability. Productivity advantages and process suitability Grade T9215 is optimised for productive turning where wear resistance and breakage prevention are priorities. The coated carbide formulation supports higher cutting speeds and sustained throughput while preserving surface finish, which benefits batch production and medium-volume runs. Selecting the insert as part of a system—appropriate outer holder or boring bar, shim or clamp set and the correct fastening hardware—ensures the cutting edge performs reliably, improving machine uptime and process economy. Practical guidance for selection and integration When integrating this insert into a tooling system, choose the holder and clamping arrangement that match the rhombic form, CPMT 06 size and the insert’s 2.38 mm thickness to guarantee stable seating and accurate positioning. The insert’s geometry and chip control suit external and internal turning tasks on medium steels; for other materials or highly interrupted cuts, compare alternative grades and chipbreakers. If clarification is required on fitment or cutting parameter recommendations, technical advice is available. Contact Metav Werkzeuge today to discuss how Tungaloy’s T9215 grade can increase throughput and tool life in medium-steel turning applications and to receive tailored holder recommendations from our specialists Technical data Manufacturer article number: 6951170 SKU: 6951170-Tungaloy Manufacturer SKU: TUN6951170 Model series: ISO turning indexable inserts Facts Corner radius: 0.8 mm Thickness: 2.38 mm Clearance angle: 11° Insert angle: 80° Size: 06 Special features Grade/coating: T9215, CVD-coated cemented carbide Plate form: rhombic (CPMT) Hole: cylindrical hole with single-sided countersink (40°–60°) Chipbreaker: one-sided Typical application: external and internal turning on medium steel System components: matching outer holder or boring bar, shim/clamp set, replacement screws FAQ What material is this insert optimised for? The CPMT060208 T9215 insert is optimised for medium-steel machining and combines wear resistance with fracture toughness for productive turning. Which holders are compatible with this insert? Compatibility depends on holder form, clearance angle, tolerance class, fastening, size and thickness; the insert fits holders designed for CPMT 06 rhombic inserts with a 2.38 mm plate thickness. How does the T9215 grade affect cutting performance? Grade T9215 delivers high wear resistance and good edge stability, making it suitable for higher cutting speeds and continuous to slightly interrupted cuts in medium-steel applications. Can this insert be used for internal turning? Yes, the geometry and chip control of the insert make it suitable for both external and internal turning where the holder permits correct mounting. What mounting features ensure secure clamping? The cylindrical hole combined with a single-sided countersink (40°–60°) provides positive clamping when used with the appropriate shim or clamp set and fastening screws. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of CVD-coated carbide toughness and ISO-standard geometry for reliable medium to heavy steel turning; the robust T9225 grade and 0.8 mm corner radius ensure consistent chip control and extended tool life — order directly via Metav Werkzeuge or consult our specialists for application advice. CPMT060208 T9225 Tungaloy indexable insert for turning (ISO 060208) CPMT060208 T9225 Tungaloy — an ISO-standard indexable turning insert designed for medium to heavy steel machining with a robust universal grade and single-sided chipbreaker CVD-coated carbide grade T9225 ISO rhombic insert, size 06 11° clearance angle for stable cutting 0.8 mm corner radius with single-sided chipbreaker Consistent performance for medium to heavy steel turning This CVD-coated carbide insert was developed to deliver reliable performance in demanding turning operations. The T9225 grade offers a balanced combination of hardness and toughness, making it suitable for variable engagement conditions and light interruptions in the cut. As part of an ISO system, the insert supports predictable wear behaviour, which helps maintain process stability and reduces unplanned downtime. The design focuses on effective chip control and repeatable edge life, translating into fewer tool changes and steadier part quality on the shop floor. ISO compatibility and secure clamping for straightforward integration The insert follows ISO geometry, so holder compatibility is defined by form, clearance angle, tolerance class, fixation, size and thickness. The rhombic shape and the specified 11° clearance ensure proper orientation in standard carriers, while the central hole with cylindrical bore and one-sided countersink (40°–60°) enables secure fastening and reliable repeatability. A thickness of 2.38 mm and the ISO code 060208 simplify selection from established toolholders and enable quick replacement without complex adjustments, supporting shorter set-up times and consistent machining results. Practical selection guidance and measurable shop-floor benefits Choose a single-sided chipbreaker and the 0.8 mm corner radius for a blend of surface finish and tool strength suited to external and internal turning tasks. The rhombic insert format facilitates varied approach angles, and the 0.8 mm corner radius provides robustness against shock while still allowing acceptable surface quality. The system approach — insert, matching external holder or boring bar, shim/clamp and spare screws — ensures predictable assembly and serviceability. For operations prioritising productivity and repeatability, this insert delivers stable cutting performance and controlled chip formation. Contact Metav Werkzeuge for tailored advice on using Tungaloy inserts in specific turning applications and to arrange supply directly from stock Technical data Article number: 6951199 SKU: 6951199-Tungaloy Manufacturer SKU: TUN6951199 Facts ISO designation: 060208 Insert size: 06 Clearance angle: 11° Corner radius: 0.8 mm Thickness: 2.38 mm Included hole: with hole; cylindrical bore + one-sided countersink (40°–60°) Insert angle: 80° Special features CVD-coated carbide Grade: T9225 Rhombic plate form Single-sided chipbreaker Application: turning (external and internal) System components: compatible external holder or boring bar, shim/clamp and replacement screws FAQ What materials is this insert best suited for? The insert is formulated in T9225 CVD-coated carbide and is intended primarily for medium to heavy steel turning, offering good toughness under variable engagement. How does the ISO designation affect holder selection? The ISO code 060208 defines the geometry and helps match the insert to compatible holders; users should check form, clearance angle, tolerance and fixation to ensure proper fit. What benefits does the single-sided chipbreaker provide? A single-sided chipbreaker promotes predictable chip formation and evacuation during turning, improving surface finish and reducing the risk of chip entanglement on standard turning operations. Is the corner radius suitable for finish turning? The 0.8 mm corner radius is a compromise between strength and finish — it enhances tool life under heavier cuts while still achieving acceptable surface quality for many applications. Does the insert require specific mounting hardware? The insert uses a central hole with a cylindrical bore and one-sided countersink; a matching clamp/shim set and the appropriate screw ensure secure, repeatable mounting in standard ISO holders. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9225 Wendeplatten - Tungaloy
Take advantage of the combination of a robust, CVD-coated cemented carbide grade and ISO compatibility for consistent productivity in medium-to-heavy steel turning; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. CPMT060208 T9225 rhomboid turning insert by Tungaloy — CVD-coated, 11° clearance The CPMT060208 T9225 is an ISO-standard rhomboid indexable insert for turning, designed for medium-to-heavy steel machining and featuring a CVD-coated cemented carbide grade with an 11° clearance CVD-coated carbide grade T9225 ISO CPMT060208 rhomboid insert Optimised one-sided chipbreaker 11° clearance; 0.8 mm corner radius Greater process stability for demanding turning operations The CVD-coated cemented carbide grade T9225 delivers a balanced combination of hardness and toughness, making the insert suitable for medium-to-heavy steel machining where variable engagement or slight interruptions occur. The coating improves wear resistance and thermal stability while the substrate provides toughness for consistent cutting performance. This results in stable chip formation and fewer unplanned tool changes, supporting continuous production and predictable component quality. Simple integration and assured compatibility with ISO systems As an ISO-sized rhomboid insert, the part conforms to the CPMT060208 designation; compatibility with a holder depends on form, 11° clearance, tolerance class, attachment method, size and thickness. The standardised geometry simplifies tool selection for existing carriers and reduces setup time. The insert’s hole and seating arrangement — a cylindrical hole with a single-sided countersink (40°–60°) — enable secure clamping and repeatable positioning in most ISO-compatible external holders and boring bars. Designed chip control and application economy The built-in one-sided chipbreaker and a 0.8 mm corner radius are optimised for steel turning, offering controlled chip formation and reduced cutting forces in typical turning tasks. Using this grade and geometry can extend effective tool life and improve surface finish, lowering per‑component tooling cost in batch and series production. For interrupted cuts or fluctuating feed, the combination of coating and substrate hardness provides a reliable balance between wear resistance and edge toughness. For tailored advice on the Tungaloy CPMT060208 T9225 insert and to secure reliable supply, contact Metav Werkzeuge—call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for a technical consultation. Technical data Article number: 6951137 SKU: 6951137-Tungaloy Manufacturer SKU: TUN6951137 Manufacturer: Tungaloy Model series: ISO turning indexable inserts Facts Size: 06 Thickness: 2.38 mm Clearance angle: 11° Corner radius: 0.8 mm Insert angle: 80° Special features Grade: T9225 Cutting material type: CVD-coated cemented carbide One-sided chipbreaker Rhomboid insert with cylindrical hole and one-sided countersink (40°–60°) Application: turning Compatibility determined by form, clearance angle, tolerance class, attachment, size and thickness FAQ What materials is this insert best suited for? The CPMT060208 T9225 indexable insert (Tungaloy, SKU 6951137-Tungaloy) is engineered primarily for medium-to-heavy steel turning and performs well under variable engagement and light interruptions. Is the insert compatible with standard CPMT holders? Yes. The CPMT060208 geometry follows ISO conventions, so compatibility depends on holder form, clearance angle, tolerance class, attachment and thickness; the insert’s cylindrical hole plus countersink ensures secure seating. What benefits does the CVD coating provide? The CVD-coated cemented carbide composition of the T9225 grade enhances wear resistance and thermal stability for longer edge life during continuous and semi-continuous turning operations. Can the insert cope with interrupted cuts? The combination of a tough carbide substrate and the T9225 coating gives the insert improved resistance to shock and mild interruptions, making it suitable for interrupted cutting conditions in steel. How does the chipbreaker affect machining? The optimised one-sided chipbreaker promotes controlled chip flow and reduces cutting forces, improving surface finish and reducing the likelihood of chip-related disruption in turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9225 Wendeplatten - Tungaloy
Take advantage of a CVD-coated carbide T9225 grade for robust medium-to-heavy steel turning and ISO standard geometry for reliable holder compatibility; order directly via Metav Werkzeuge or consult technical advisors for application-specific selection. CPMT 060208 T9225 Turning insert (ISO) — CVD-coated carbide, rhombic 80° — Tungaloy A CPMT 060208 T9225 indexable turning insert designed for durable external and internal turning in steel, offering a robust universal grade for slightly interrupted cuts and variable engagement conditions CVD-coated carbide grade T9225 Universal grade for medium to heavy steel ISO CPMT 060208 rhombic insert Cylindrical hole with 40°–60° countersink Consistent cutting performance for steel turning The insert delivers stable machining under variable engagement thanks to the T9225 CVD-coated carbide grade, which combines wear resistance with increased toughness. The composition is optimised for medium-to-heavy steel work, making it suitable when occasional interruptions or changes in cutting conditions occur. As an ISO-standardised component, the geometry supports predictable performance and simplifies process planning for production environments aiming for consistent cycle times and surface quality. Geometry and clamping that ensure interchangeability The rhombic plate form with an 80° included angle and a 11° clearance angle provides a secure cutting edge while maintaining straightforward seat compatibility. Key dimensions such as insert size 06, thickness 2.38 mm, and corner radius 0.8 mm make the part compatible with commonly used external holders when the correct tolerance class and fixing method are observed. The cylindrical hole with a single-side countersink (40°–60°) supports positive clamping and stable seating, reducing the risk of movement under higher cutting loads. Coating, chip control and edge stability explained A CVD coating on a carbide substrate improves resistance to abrasive wear and thermal degradation, extending tool life in longer turning cycles. The one-sided chipbreaker is tuned for chip form and evacuation during steel turning, helping to maintain consistent surface finish and reducing downtime for chip clearing. These technical attributes translate into fewer insert changes and more predictable tool costs over a production run, supporting productivity targets in small-batch and continuous operations alike. Practical application and selection guidance for productivity Intended primarily for turning, the insert performs in both external and internal operations when paired with a compatible external holder or boring bar, the appropriate support shim and correct clamping set. Selection of the chipbreaker and grade should follow the workpiece material, stability of the setup and expected cut interruptions. For process optimisation, match the insert with a holder that accommodates the ISO CPMT 060208 geometry and the specified thickness to ensure repeatable positioning and minimal setup variation. For supply and application advice on Tungaloy inserts such as the CPMT 060208 T9225, contact Metav Werkzeuge for precise recommendations and ordering — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6951171 SKU (vendor): 6951171-Tungaloy Manufacturer SKU: TUN6951171 Model series: ISO indexable turning inserts Facts Insert size: 06 Thickness: 2.38 mm Corner radius: 0.8 mm Clearance angle: 11° Included angle: 80° Grade: T9225 Material: carbide Special features Rhombic plate form Cylindrical hole with single-side countersink (40°–60°) One-sided chipbreaker ISO designation: CPMT060208 Application: Turning FAQ What materials is this insert suitable for? The CPMT 060208 T9225 is formulated as a robust universal grade for steel machining and performs well in medium-to-heavy cutting of steel workpieces, particularly where occasional interruptions occur. How does the T9225 grade affect tool life? The T9225 CVD-coated carbide grade improves wear resistance and edge stability, which typically extends insert life in steel turning compared with uncoated grades under similar cutting conditions. Which holder features are required for correct use? Use a holder compatible with ISO CPMT 060208 geometry: correct seat form, matching thickness (2.38 mm), the specified clearance angle and proper clamping to accommodate the cylindrical hole with countersink. Can this insert be used for finishing operations? Yes; when combined with appropriate feeds, speeds and a stable setup, the insert and its one-sided chipbreaker can achieve good surface finishes in turning, though finish requirements may call for a smaller corner radius where applicable. Is the CPMT 060208 compatible with internal boring bars? The geometry supports internal applications where the holder accepts ISO rhombic inserts of size 06 and the clamping system matches the insert thickness and hole style; verify toolholder clearance for the 80° included angle prior to application. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 060208 T9225 Wendeplatten - Tungaloy
Benefit from the combination of CVD-coated carbide toughness, ISO compatibility and a stable rhombic geometry for reliable medium to heavy steel turning; order directly via Metav Werkzeuge or consult our specialists for application-specific guidance. CPMT 060208 T9225 — Tungaloy ISO turning insert, 0.8 mm corner radius CPMT 060208 T9225 is an ISO-format rhombic turning insert designed for robust medium to heavy steel machining with a focus on stability and secure clamping CVD-coated carbide grade T9225 ISO-compatible geometry for easy replacement Rhombic 80° shape for stable turning Cylindrical hole with single-sided countersink High-performance grade and material benefits for longer tool life The CVD-coated carbide composition of this insert combines wear resistance with increased toughness, making the T9225 grade especially suitable where cuts are intermittent or cutting conditions vary. As a result, cycle times are stabilised and tool-change frequency is reduced, which directly supports productivity gains on batch and job-shop operations. The indexable insert design enables quick replacement and consistent cutting-edge geometry, lowering set-up time and helping to maintain repeatable surface quality. Geometry and clamping that ensure process security and fitment Engineered as an ISO-series rhombic plate with an 80° working angle and 11° clearance angle, the insert offers good contact stability in common external and internal turning holders. The 0.8 mm corner radius provides a balance between edge strength and surface finish, while the cylindrical hole with single-sided countersink (40°–60°) ensures reliable mechanical clamping. Compatibility with a given holder depends on form, clearance angle, tolerance class, fastening, size and thickness, so straightforward retrofitting is possible where ISO dimensions are observed. Practical application guidance that reduces machining risk Intended for turning, the robust universal grade performs well in medium to heavy steel machining and supports operators who must handle variable engagement or semi-interrupted cuts. The single-sided chipbreaker and the insert’s geometry promote predictable chip formation and evacuation under stable clamping conditions, helping to lower the risk of edge breakage and improve process reliability. For optimized results, match the chipbreaker and grade to the workpiece material, machining stability and the chosen cutting parameters; Metav Werkzeuge can advise on the best combination for a given job. Contact Metav Werkzeuge for application-specific recommendations on the CPMT 060208 T9225 insert and to secure original Tungaloy products (info@metav-werkzeuge.com, +49 2822 7131930) Technical Data Article number: 6781188 Manufacturer article number: 6781188 Manufacturer SKU: TUN6781188 SKU: 6781188-Tungaloy Model series: ISO turning indexable inserts Core specifications Corner radius: 0.8 mm Approach/working angle: 80° Clearance angle: 11° Plate thickness: 2.38 mm Plate size: 06 Materials and special features Material: carbide Coating / grade: T9225 (CVD-coated) Plate form: rhombic Chipbreaker: one-sided Hole style: cylindrical hole + single-sided countersink (40°–60°) Application: turning FAQ Is this insert suitable for interrupted cuts? The CPMT 060208 T9225 turning insert (SKU 6781188-Tungaloy) is a robust universal grade with increased toughness, making it suitable for light to moderate interruptions in steel turning applications. Which workpiece materials are recommended for this grade? The T9225 CVD-coated carbide grade is designed primarily for medium to heavy steel machining, offering a broad material coverage under varying engagement conditions. Can this plate be used for internal and external turning? Yes, the ISO-format rhombic geometry of the CPMT 060208 insert supports both external and internal turning when combined with the appropriate holder and clamping configuration. What determines compatibility with a toolholder? Compatibility is governed by plate form, clearance angle, tolerance class, fastening method, plate size and thickness; matching these parameters ensures secure clamping and correct seating of the insert. How does the hole and countersink benefit clamping reliability? The cylindrical hole with a single-sided countersink (40°–60°) provides positive seating and improved axial stability under clamping, which contributes to consistent cutting performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 080202 AH6225 Wendeplatten - Tungaloy
High-performance PVD-coated AH6225 carbide insert delivers a sharp yet stable cutting edge for stainless steels, combined with ISO-standard geometry for straightforward holder compatibility and secure clamping. Benefit from predictable chip control and extended tool life; order directly via Metav Werkzeuge or consult our specialists for application advice. CPMT080202 AH6225 ISO turning insert — PVD-coated carbide, 80° rhombic | Tungaloy The CPMT080202 AH6225 Tungaloy insert is an ISO-standard rhombic turning insert engineered for external and internal turning in stainless steels, offering a robust cutting edge for medium machining under changing conditions. PVD-coated carbide for tough performance 80° rhombic geometry for versatile turning 11° clearance angle for stable cutting Single-sided chipbreaker; hole with countersink Consistent cutting performance for stainless steels The CPMT080202 AH6225 grade is a PVD-coated carbide developed as a universal solution for stainless steels, optimised to maintain a sharp, stable cutting edge during medium cutting operations. The coating increases surface hardness and provides wear resistance, which translates into longer tool life and fewer insert changes in mixed-production environments. The combination of grade and geometry enables reproducible results on a range of components where consistent dimensional accuracy and predictable tool behaviour are required. Secure seating and reliable chip control reduce downtime Featuring an 80° rhombic shape together with an 11° clearance angle, the insert seats confidently in ISO-standard holders and promotes stable cutting conditions. The single-sided chipbreaker and the centre hole with cylindrical bore plus a single-side countersink (40°–60°) support controlled chip formation and evacuation, reducing the risk of built-up edge and minimising vibration. These design choices improve surface finish and help to keep cycle times steady across batches, especially where workpiece stability varies. Productivity gains through fewer tool changes and easy integration Because the grade is tailored for varied machining conditions, the insert helps to lower process costs by reducing tool turnover and improving uptime. The ISO-standard format simplifies tool management: form, clearance angle, tolerance class, fastening, size and thickness determine holder compatibility, allowing rapid replacement with predictable results. For manufacturing operations focused on throughput and repeatability, the PVD-coated carbide insert supports higher productivity and consistent part quality. Choose the original Tungaloy CPMT080202 AH6225 insert via Metav Werkzeuge for stable performance in stainless steel turning; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored application advice or ordering assistance Technical data Article number: 6903273 SKU: 6903273-Tungaloy Manufacturer SKU: TUN6903273 Manufacturer: Tungaloy Numbers / Core technical data Geometry angle: 80° Clearance angle: 11° Thickness: 2.38 mm Corner radius: 0.2 mm Size: 08 Designs / Special features Shape: rhombic insert Hole: with cylindrical hole + single-side countersink (40°–60°) Chipbreaker: single-sided Grade/coating: AH6225, PVD-coated carbide Application: Turning; suited for stainless steels Model series: ISO turning inserts FAQ Which materials is this insert intended for? The CPMT080202 AH6225 insert is intended primarily for stainless steels; the AH6225 grade and PVD coating are chosen to provide wear resistance and a stable cutting edge in those materials. How does the 0.2 mm corner radius affect machining? A corner radius of 0.2 mm on the CPMT080202 AH6225 balances edge strength and surface finish, making it suitable for medium cutting depths where both accuracy and edge robustness are required. What holder features are required for proper compatibility? Compatibility depends on the insert form, clearance angle, tolerance class, fastening, size and thickness; the CPMT080202 fits ISO pockets designed for 80° rhombic inserts with the corresponding clamping system. Is the chip control suitable for long, continuous cuts? The single-sided chipbreaker combined with the insert geometry promotes reliable chip formation and evacuation, supporting longer continuous cuts under appropriate cutting conditions with the AH6225 grade. Is this an ISO-standard insert and how does that help tool management? Yes, the CPMT080202 is an ISO-standard turning insert; using ISO formats simplifies tool inventory, replacement and process planning across compatible holders and tool systems. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 080202 AH6235 Wendeplatten - Tungaloy
Combine robust PVD-coated carbide toughness with precise chip control for reliable turning in challenging materials; the insert’s ISO format and defined geometry simplify tool selection and reduce downtime. Order the CPMT080202 AH6235 insert directly via Metav Werkzeuge or consult their specialists for holder compatibility and cutting-condition advice. CPMT080202 AH6235 Tungaloy indexable turning insert — PVD-coated carbide, single-sided chipbreaker The CPMT080202 AH6235 is an ISO-standard indexable turning insert designed for external and internal turning, optimised for rostfreier Stahl and interrupted cuts. PVD-coated carbide for toughness ISO-standard form CPMT for straightforward matching Single-sided chipbreaker for controlled chips Cylindrical hole with 40°–60° countersink Increase uptime with consistent edge stability The PVD-coated AH6235 grade is formulated for increased toughness, offering improved resistance to chipping in heavy or interrupted cuts. By prioritising edge stability, the insert delivers predictable chip formation and fewer unplanned tool changes, which increases productive machine time. For applications in rostfreier Stahl, the tougher coating and substrate combination reduces the risk of built-up edge and premature failure, translating into more consistent component quality and less rework. Easier integration through ISO conformity and clear geometry As an ISO-standard insert in the CPMT family, the component integrates into existing toolholder systems where the holder match depends on form, relief angle, tolerance class, fixing method, size and thickness. Key geometry values such as the 11° relief angle, 80° included angle, 2.38 mm thickness and 0.2 mm nose radius help to select the right holder and set up cutting parameters quickly. The cylindrical hole with single-side countersink (40°–60°) ensures secure clamping and repeatable seating, reducing set-up time and limiting variability between inserts. Reliable performance for interrupted and demanding turning With a single-sided chipbreaker and a tough carbide substrate, this insert is tailored to operations with increased breakout risk and intermittent engagement. The chipbreaker design supports consistent chip evacuation and improved surface finish while the grade’s fracture resistance helps maintain a reliable cutting edge under shock loads. Use this insert where steady dimensional results and reduced post-process finishing are priorities; the combination of geometry and PVD coating provides a balanced compromise between wear resistance and toughness. Contact Metav Werkzeuge for a compatibility check and recommendations on cutting data for the CPMT080202 AH6235 insert to ensure the optimal combination of holder and grade for the application Technical Data Article number: 6903457 Manufacturer SKU: TUN6903457 SKU: 6903457-Tungaloy Facts Included angle: 80° Relief angle: 11° Thickness: 2.38 mm Nose radius: 0.2 mm Size: 08 Special features ISO turning insert series CPMT080202 PVD-coated AH6235 carbide grade Single-sided chipbreaker Cylindrical hole + single-side countersink (40°–60°) Suitable for rostfreier Stahl and interrupted cuts FAQ What materials is this insert suitable for? The CPMT080202 AH6235 insert is designed primarily for rostfreier Stahl and applications with interrupted cuts, where its tougher PVD-coated carbide grade helps to prevent edge fracture. How does the AH6235 grade affect tool life? AH6235’s combination of a tough substrate and PVD coating improves resistance to chipping and edge breakage, which often leads to longer effective tool life under heavy or interrupted turning conditions. Which holders are compatible with this ISO insert? Compatibility depends on holder form, relief angle, tolerance class, fixing method, size and thickness; the CPMT080202 form is an ISO-standard shape used with matching CPMT external holders or boring bars. What does the CPMT080202 code mean? The CPMT designation identifies the rhombic insert geometry and size; 080202 specifies the size and nose radius class, allowing consistent selection across ISO-compliant tool systems. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CPMT 080202 AH725 Wendeplatten - Tungaloy
The proven AH725 grade and PVD-coated carbide deliver stable chip formation and high process security, while the ISO‑conforming rhombic geometry with an 80° included angle and 11° clearance ensures compatibility with standard holders; order directly via Metav Werkzeuge or request specialist advice for optimal tool pairing. CPMT080202 AH725 ISO turning insert — rhombic 80° geometry, 11° clearance — Tungaloy A CPMT080202 AH725 ISO‑standard insert designed for reliable external and internal turning where universal, breakage‑resistant performance across Stahl and rostfreier Stahl is required PVD-coated carbide grade AH725 Universal for Stahl and rostfreier Stahl Rhombic 80° geometry, 11° clearance Cylindrical hole with one‑side countersink Dependable, universal cutting performance for varied turning tasks The combination of a PVD‑coating and the AH725 carbide grade provides a balance between wear resistance and edge toughness, making this insert particularly suited for mixed material runs and applications demanding consistent results. The universal character of the grade reduces tool inventory complexity while maintaining cutting stability for both roughing and finishing passes. Emphasis on stable chip formation and predictable tool life helps to reduce unplanned downtime and supports steady production throughput. ISO conformity and secure mounting for rapid tool changes Dimensionally consistent with ISO specifications, the insert’s rhombic form and 80° included angle make it compatible with a wide range of external holders and boring bars when form, clearance, tolerance class, fastening, size and thickness are matched. The cylindrical hole with one‑side countersink (40°–60°) enables secure clamping and repeatable seating; the plate thickness 2.38 mm and 0.2 mm corner radius are optimised for small to medium tool blocks. Clear information about holder compatibility simplifies selection and shortens change‑over times in machining cells. Improved process security and practical system integration A single‑sided chipbreaker and the insert’s fracture‑resistant construction support reliable swarf control and stable machining in variable conditions. The insert is intended to operate within a system comprising an ISO insert, a suitable external holder or boring bar, a shim/clip and replacement screws, allowing straightforward replacement and maintenance. Choosing the correct chipbreaker style and grade for the workpiece material will maximise tool life and surface quality while supporting consistent cycle times. For tailored application advice on the Tungaloy AH725 grade and to confirm holder compatibility, contact Metav Werkzeuge for specialist consultation and prompt supply arrangements via email or phone Technical data Article number: 6865480 Manufacturer SKU: TUN6865480 Label / name: CPMT080202 AH725 Tungaloy‑insert Series: ISO‑Drehwendeschneidplatten Material: Hartmetall Facts Included angle: 80° Clearance angle: 11° Corner radius: 0.2 mm Plate thickness: 2.38 mm Size designation: 08 Special features PVD‑coated carbide, grade AH725 Single‑sided chipbreaker Rhombic plate form Cylindrical hole with one‑side countersink (40°–60°) Universal, breakout‑resistant for Stahl and rostfreier Stahl Intended application: Drehen (external and internal turning) System components: ISO insert, external holder/boring bar, shim/clip, replacement screws FAQ What materials are suitable for this insert? The AH725 grade is designed as a universal solution for machining Stahl and rostfreier Stahl, offering good resistance to edge chipping while maintaining wear performance. How is the insert mounted and secured in the holder? Mounting relies on the ISO‑conforming geometry: the cylindrical hole with a one‑side countersink (40°–60°) ensures stable clamping when used with the correct shim/clip and fastening screws in the designated external holder. Which chipbreaker should be selected for best performance? Selection depends on the operation; the supplied single‑sided chipbreaker is suitable for a wide range of turning tasks, but choosing a chipbreaker variant matched to material grade and cutting parameters improves swarf control and surface finish. Is the CPMT080202 AH725 suitable for small‑diameter toolholders? Yes. The insert’s 2.38 mm thickness and compact 08 size make it appropriate for smaller tools where space and rigidity constraints require a balance between strength and insert footprint. Can this insert be used for both roughing and finishing? The AH725 grade and the insert’s edge geometry make it versatile for both heavier cuts and finishing passes when cutting data and tool setup are optimised for the workpiece. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com