Which manufacturers offer high-quality 3-point internal micrometers?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of precise 0.005 mm reading, a self‑centring three‑point measuring mechanism and interchangeable measuring inserts to ensure reproducible internal measurements of blind bores in the standard workshop range. Order the instrument directly via Metav Werkzeuge or consult the Metav team for application advice. Three‑point internal micrometer MS908.665 — self‑centring, 150–175 mm range (Metav IndustryLine) The three‑point internal micrometer is an analogue internal measuring instrument designed for reliable measurement of blind bores and internal diameters in the workshop and production environment. Self‑centring three‑point design Measurement range 150–175 mm Analogue reading 0.005 mm resolution Hardened measuring faces, interchangeable insert Reliable metrology for internal diameters and blind bores The three‑point design offers consistent contact on the bore surface, enabling reproducible centring even in deep blind holes. With a measurement range of 150–175 mm this instrument fits the standard class of workshop metrology where reach, stiffness and one‑hand operation are required. The analogue scale provides a clear 0.005 mm reading and an equivalent stated accuracy, which supports routine quality checks and rapid go/no‑go decisions on the shop floor. Practical handling and application benefits for production Interchangeable measuring inserts allow adaptation to differing bore geometries without replacing the whole instrument, reducing downtime and consumable cost. The self‑centring mechanism simplifies alignment and lowers operator variability, which increases throughput and decreases rework. Designed for internal measurements including blind bores, the tool is particularly suitable for machine shops, toolrooms and maintenance departments that require straightforward, rugged measuring devices for repeat measurements. Construction and durability tailored to industrial use Hardened measuring faces reduce wear and maintain measurement fidelity over long service periods; the instrument’s analogue mechanics are engineered for robustness rather than electronic sensitivity. The combination of hardened anvils, an interchangeable insert system and solid construction ensures long‑term stability under workshop conditions and predictable measurement behaviour when performing internal diameter checks on components. Contact Metav Werkzeuge in Emmerich for tailored advice on the MS908.665 three‑point internal micrometer and to arrange delivery from stock — info@metav-werkzeuge.com | +49 2822 7131930 Technical Data Article number: MS908.665 Name: Three‑point internal micrometer (Dreipunkt‑Innenmessschraube) Manufacturer: Metav IndustryLine Core technical data Measurement range: 150–175 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 145 mm Analogue instrument Special features Self‑centring three‑point design Hardened measuring faces Interchangeable measuring insert Suitable for blind bores Analogue scale, workshop grade FAQ What measuring range does the MS908.665 cover? The MS908.665 three‑point internal micrometer by Metav IndustryLine covers a measurement range of 150–175 mm. How fine is the resolution and what accuracy is stated? The instrument provides an analogue reading with 0.005 mm resolution and a stated accuracy of 0.005 mm for routine workshop control. Is the design suitable for blind hole measurements? Yes, the three‑point geometry and self‑centring action of this micrometer make it particularly suitable for reliable measurements in blind bores. Can the measuring faces be replaced if worn? The MS908.665 features an interchangeable measuring insert system; hardened faces prolong service life and can be renewed through the insert mechanism. For which workshop tasks is this micrometer intended? The instrument is designed for internal diameter checks in machine shops, toolrooms and maintenance operations where robust, repeatable analogue measurement is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the self-centring three-point system and interchangeable measuring insert for reliable blind-hole measurements; combined with carbide measuring faces and an accuracy of ±0.007 mm, this instrument supports consistent quality control. Order the (three-point internal micrometer MS908.667) directly via (Metav Werkzeuge) or ask our consultants if needed. Three-point internal micrometer MS908.667 — self-centring, interchangeable insert The three-point internal micrometer for precise measurement of blind bores in workshop and inspection environments, designed as a mechanical instrument for repeatable internal diameter checks. Self-centring three-point system Interchangeable measuring insert Carbide measuring faces for wear resistance High precision ±0.007 mm Reliable blind-bore measurement with minimal operator influence The three-point system centres automatically within blind bores, reducing alignment errors and giving a reproducible contact geometry; this produces consistent results when inspecting bores. With a reading resolution of 0.005 mm (vernier) and a stated accuracy of ±0.007 mm, the instrument narrows measurement uncertainty to a level suitable for many workshop and production control tasks. The effect is a measurable reduction in rework and faster go/no-go decisions on turning and drilling operations. Durable contact surfaces and easy servicing save time Hard-wearing carbide measuring faces extend service intervals and maintain measurement integrity under repeated use. The measuring insert is exchangeable, which simplifies maintenance and allows quick replacement of worn contacts without discarding the whole instrument. The mechanical construction is straightforward and low-maintenance compared with electronic systems, making it suitable for environments where robustness and simple servicing are priorities. Size and handling tuned to everyday workshop needs Classified in the standard measuring range (measuring range 200–225 mm), this device offers a practical balance of reach and stiffness for typical machine‑shop components such as housings, sleeves and medium-sized bores. The instrument’s overall length of 145 mm supports good accessibility in confined bores while remaining easy to handle during repeated checks. As an analogue instrument with a vernier readout, it performs reliably where electronic readouts are unnecessary or undesired. Confidence for quality control and process stability Intended for routine inspection and in-process checks, the micrometer’s self-centring action and robust contact faces reduce operator-dependent variation and increase throughput in batch inspection. The interchangeable insert concept supports lifecycle planning: wear parts can be stocked and replaced quickly to maintain traceable measurement performance. The device is suitable for blind-hole measurement tasks and integrates well into manual quality-control workflows where mechanical verifiability is required. Contact Metav Werkzeuge today for ordering details and specification advice on the Metav IndustryLine three-point internal micrometer MS908.667 and its spare measuring inserts Technical Data Article number: MS908.667 Manufacturer: Metav IndustryLine Category: Micrometers (internal micrometer) Facts Measuring range: 200–225 mm Reading / Resolution: 0.005 mm Accuracy: ±0.007 mm Overall length: 145 mm Display: analogue (vernier) Features & Delivery Self-centring three-point system Carbide measuring faces Interchangeable measuring insert Designed for blind bores (blind-hole measurement) Mechanical, analogue instrument FAQ How does the three-point centring reduce measurement error? The self-centring three-point mechanism distributes contact forces evenly; the three-point internal micrometer MS908.667 centres itself in the bore to reduce eccentricity and improve repeatability. Can the measuring faces be replaced when worn? Yes — the instrument is fitted with an exchangeable measuring insert, so worn carbide faces can be renewed without replacing the entire micrometer. Is the reading digital or mechanical? The device uses a mechanical vernier readout with a reading resolution of 0.005 mm, offering a robust, electronics-free solution for workshop environments. For which bore types is this instrument intended? It is designed specifically for blind bores; the three-point configuration ensures reliable contact geometry in such applications. What is the measuring range and typical accuracy? The measuring range is 200–225 mm and the stated accuracy is ±0.007 mm, suitable for standard workshop inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of self‑centring three‑point measurement and carbide measuring faces for consistent, reproducible results in blind‑hole bores; the interchangeable measuring inserts allow flexible adaptation across the nominal range. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.668 — self‑centring, carbide faces (Metav IndustryLine) The MS908.668 is a three‑point internal micrometer for accurate measurement of blind‑hole bores in workshop and inspection environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Interchangeable measuring inserts Delivered in protective case Faster, repeatable centring in blind‑hole measurement The self‑centring three‑point measuring head significantly reduces setup time when inspecting blind‑hole bores. By contacting the bore with three equidistant measuring points the instrument centres itself automatically, which improves repeatability compared with two‑point probes and speeds up routine checks. The analogue mechanism keeps the operation straightforward for technicians and maintenance staff who require reliable results without complex electronics. Metrology performance you can rely on Designed for industrial use, the instrument offers a stated accuracy 0.007 mm and a resolution 0.005 mm, values that make it well suited for quality control in machining and assembly. These specifications mean the device detects small deviations while providing a clear mechanical indication of the measurement. The combination of robust mechanical gearing and a clear, fine graduation supports precise readings under standard workshop conditions, helping to maintain product tolerances and reduce the risk of costly rework. Durable contact surfaces and flexible inserts The measuring faces are carbide tipped to resist wear during frequent use, preserving the nominal geometry and ensuring long‑term stability. Interchangeable measuring inserts permit adaptation across the stated measuring span so one instrument can cover a range of bore diameters without compromising accuracy. Supplied in a protective case, the tool is ready for transport to the machine or for storage in an inspection cabinet, keeping the measuring faces protected between uses. Trusted partner for precision tasks As part of the Metav IndustryLine range, this three‑point internal micrometer benefits from the supplier’s focus on accessibility and reliability. Metav’s approach to precision brings workshop‑grade metrology within reach, backed by a broad product portfolio and proven logistical support from Emmerich. The instrument suits metrology labs, maintenance teams and production lines that prioritise consistent centring, wear resistance and straightforward operation. For expert advice or to purchase the Metav IndustryLine three‑point internal micrometer MS908.668 with interchangeable inserts and carbide faces, please contact Metav Werkzeuge for tailored assistance and fast supply Technical data Article number: MS908.668 Brand: Metav IndustryLine Category: Messschrauben Numbers / Facts Measuring range: 225–240 mm Resolution (reading): 0.005 mm Accuracy: 0.007 mm Length: 145 mm Analogue instrument Special features / Versions Self‑centring three‑point measuring head Carbide measuring faces Interchangeable measuring inserts Suitable for blind‑hole bores Supplied in protective case FAQ What measuring range does the instrument cover? The MS908.668 three‑point internal micrometer covers a measuring span from 225 mm to 240 mm as delivered. Is this tool suitable for blind‑hole measurements? Yes; the three‑point, self‑centring design is specifically intended for reliable measurement of blind‑hole bores. Can the measuring inserts be replaced to adjust for different bore sizes? Interchangeable measuring inserts are provided, allowing the instrument to be adapted across its nominal measuring span. How precise are the readings from this analogue instrument? The instrument provides a resolution of 0.005 mm with a stated accuracy of 0.007 mm, suitable for workshop and production quality checks. Are the measuring faces durable under regular workshop use? The contact points are carbide tipped to increase wear resistance and maintain geometric integrity over extended use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise 0.004 mm accuracy, a self‑centring three‑point measuring head and carbide measuring faces for consistent blind‑hole measurement; order directly via Metav Werkzeuge or contact the consultancy team for tailored advice. MS908.656 Three‑Point Internal Micrometer — Self‑centring, 25–30 mm range (Metav IndustryLine) A three‑point internal micrometer designed for accurate measurement of blind holes and restricted bores in the 25–30 mm range, combining a compact form with stable contact geometry. Three‑point self‑centring measuring head Measuring range 25–30 mm Carbide measuring faces for wear resistance Analogue drive with 0.005 mm resolution Consistent results for blind‑hole inspection The instrument's self‑centring three‑point system guarantees repeatable contact with bore surfaces, reducing setup variance and rework in production inspection. The compact contact geometry suits restricted bores where standard callipers cannot reach, while the analogue drive and fine spindle allow controlled approach to the measuring surfaces. This configuration translates directly into fewer rejected parts and more reliable pass/fail decisions on the shop floor. Precision that meets workshop demands With a documented accuracy of 0.004 mm and a readable resolution of 0.005 mm, the device sits between general workshop tools and high‑precision instruments. The mechanical design and robust spindle ensure stable readings even in routine quality control. For applications that require exact internal diameters in small assemblies, this micrometer provides a balance of sensitivity and practical handling without invoking complex electronic systems. Durable contact surfaces for long service life The measuring faces are made from carbide, offering superior wear resistance under frequent use and abrasive conditions. That hard contact material preserves the reference geometry over many cycles and keeps measurement uncertainty low. An adjustment ring marked 25 assists with quick reference when setting or checking the nominal diameter, making repetitive tasks more efficient and less error‑prone. Compact format for fine mechanical work Classified in the micro range by its 25–30 mm span, the tool is ideal where small, precise components are involved. The short overall length supports handling in confined environments and maintains torsional stiffness for reliable contact pressure. As an analogue internal measuring instrument, it offers familiar operation for technicians while delivering the benefits of a three‑point system designed specifically for blind‑hole measurement. For precise and repeatable blind‑hole measurement, contact Metav Werkzeuge to request the Metav IndustryLine three‑point internal micrometer MS908.656 or to speak with a specialist at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: MS908.656 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Facts Measuring range: 25–30 mm Resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features Self‑centring three‑point measuring head Carbide measuring faces Analogue micrometer design Adjustment ring marked 25 Suitable for blind‑hole measurement FAQ What measuring range does this instrument cover? The three‑point internal micrometer MS908.656 covers a measuring range of 25–30 mm, suited to small‑bore and blind‑hole applications. Is this micrometer suitable for blind‑hole measurement? Yes, the self‑centring three‑point system of the Metav IndustryLine three‑point internal micrometer is specifically designed to measure blind holes and restricted bores reliably. What accuracy and resolution can be expected? The instrument provides an accuracy of 0.004 mm with an analogue readable resolution of 0.005 mm, offering precise control for workshop inspections. Are the measuring faces durable for repeated use? The measuring faces are made of carbide, ensuring wear resistance and long‑term stability of the contact geometry under frequent measurement cycles. How is the instrument adjusted for repetitive tasks? An adjustment ring marked 25 is provided for quick reference and repeatable setting when working with the same nominal diameters. Is this a digital instrument? No, the MS908.656 is an analogue internal micrometer, combining mechanical reliability with a fine spindle for controlled readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com