Which micrometer is used to measure the inner diameter of a bore?

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Benefit from the combination of three-point contact stability, a colour touchscreen readout and ISO 17025 traceable calibration to secure reproducible internal measurements in the 10.0–12.0 mm range. Order the Three‑Point Internal Micrometer directly via Metav Werkzeuge or consult our specialists for integration advice. Three‑Point Internal Micrometer — digital instrument with Wireless + USB (Microtech Metrology) The Three‑Point Internal Micrometer is a precision instrument for stable internal diameter measurement in small bores, suitable for quality control and bench metrology in workshops and production. Three-point contact for stable internal measurements Colour 1.5" touchscreen for clear readouts Wireless and USB data output for traceable transfer Delivered calibrated to ISO 17025 with certificate Dependable accuracy where tight tolerances matter The instrument combines a three-point contact measuring head with a high‑precision mechanism to reduce runout and centring error, delivering an accuracy of ±0.004 mm across its measuring span. With a measuring range of 10.0–12.0 mm, this device is aimed at fine internal dimensions where repeatability and a low measurement uncertainty are decisive. The robust contact geometry and confirmed specification make it well suited to small‑bore inspection tasks in component finishing and final inspection workflows, supporting a rational decision process for integrating metrology into production control. Seamless data capture for quality documentation Digital measurement is presented on a Colour 1.5" touchscreen for fast reading and reduced interpretation errors; the unit also provides Wireless and USB data output for direct transfer into SPC systems or inspection software. Combined with the included calibration trace, this workflow supports rapid documentation and traceability. The instrument’s readable display and straightforward data export reduce process steps and the risk of transcription mistakes, promoting efficiency and error‑resilient quality reporting in serial inspection and laboratory environments. Practical design for everyday workshop use A compact measuring head with an extended measuring depth of 154 mm keeps handling comfortable while reaching into bores and recesses. A setting ring is included to simplify zeroing and periodic checks. Delivered fully calibrated to ISO 17025, the micrometer arrives with a formal calibration certificate, providing immediate confidence for compliance audits and internal quality routines. The combination of robust measuring geometry, clear digital feedback and certified calibration supports both operational ease and trustworthy results, reinforcing productive workflows and peace of mind in routine inspections. For traceable high‑precision internal measurement solutions from Microtech Metrology, contact Metav Werkzeuge for ordering and application support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 133701210 GTIN: 4061905074202 Manufacturer: Microtech Metrology Numbers Measuring range: 10.0–12.0 mm Measuring depth: 154 mm Accuracy: ±0.004 mm Resolution/readout: 0.0001 mm Special features Digital display: Colour 1.5" touchscreen Data output: Wireless and USB Setting ring: included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered with a calibration certificate? Yes. The Three‑Point Internal Micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the calibration certificate for traceability. What measurement range is covered by this micrometer? The device covers internal diameters from 10.0 to 12.0 mm and is designed specifically for high‑precision work within that span. How is measured data transferred to a PC or quality system? Measurement results can be exported via both Wireless and USB connections, enabling straightforward integration into inspection software and SPC workflows. What advantage does the three‑point contact offer? Three contact points centre in the bore automatically, reducing eccentricity and improving repeatability compared with two‑point methods, which is why this geometry is preferred for small‑bore internal measurements. Can the micrometer reach recessed bores? Yes. The instrument’s 154 mm measuring depth allows access to deeper internal features while maintaining the necessary measurement stability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the self‑centring three‑point contact, the 175–200 mm measuring range and the proven 0.005 mm accuracy to ensure reliable blind‑hole checks in routine inspection. Order the instrument directly via Metav Werkzeuge or ask the consultants for application advice. Three‑Point Internal Micrometer (MS908.666) — Self‑centring, 175–200 mm range; 0.005 mm accuracy Three‑Point Internal Micrometer (MS908.666) is a mechanical measuring instrument designed for precise measurement of blind holes in the standard workshop range. Self‑centring three‑point contact system Measuring range 175–200 mm High accuracy 0.005 mm Interchangeable measuring anvils Reliable centring for blind‑hole measurement The self‑centring three‑point contact design guarantees consistent alignment with the bore axis, reducing operator‑dependent variance during inspections. With a measuring range of 175–200 mm, this instrument falls into the standard class for workshop metrology: it combines sufficient reach with manageable stiffness for repeatable checks on housings and medium‑sized components. The mechanical, analog construction gives direct tactile feedback when seating the contacts, which supports quick decision‑making on the shop floor and lowers cycle time for routine checks. Accurate results with carbide measuring faces Equipped with carbide measuring faces, the gauge provides wear resistance where contact durability matters most. The specified accuracy of 0.005 mm positions the instrument for high‑precision internal measurement tasks where sub‑hundred‑micrometre reproducibility is required. This level of accuracy is communicated as a clear, quantifiable benefit: fewer reworks, more reliable acceptance testing and better conformity with drawing tolerances during incoming or in‑process inspections. Adaptable anvils for different bore conditions Interchangeable measuring anvils increase the micrometer’s versatility: the exchangeable heads allow adaptation to varying bore geometries and surface finishes without sacrificing the calibration baseline. For workshops that encounter a range of blind‑hole diameters, the ability to switch measuring faces minimises downtime and reduces the need for multiple dedicated gauges, thereby improving operational efficiency and tool inventory management. Robust, workshop‑ready mechanical design The analogue mechanism with a precise reading increment of 0.005 mm is robust and straightforward to maintain in industrial environments. The solid mechanical construction suits regular use in inspection benches and quality departments where resilience and uncomplicated operation are priorities. The compact feel combined with the instrument’s length makes it practical for ergonomic handling during repeated measurements, supporting consistent measurement practice and traceable results. For precise blind‑hole inspections, contact Metav Werkzeuge to discuss the Three‑Point Internal Micrometer MS908.666 and its interchangeable anvils for seamless integration into existing inspection routines. Technical data Article number: MS908.666 Product type: Three‑point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 175–200 mm Minimum range: 175 mm Maximum range: 200 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 145 mm Operation: Analog Special features Self‑centring three‑point contact Interchangeable measuring anvils Carbide measuring faces Suitable for blind‑hole measurement Mechanical design for workshop use FAQ What measuring range does the instrument cover? The Three‑Point Internal Micrometer MS908.666 from Metav IndustryLine covers a 175–200 mm measuring range. How precise is the three‑point internal micrometer? The gauge delivers an accuracy of 0.005 mm, offering high repeatability for internal bore checks. Can the measuring faces be changed for different bores? Yes, the instrument features interchangeable measuring anvils, allowing adaptation to varying bore geometries without replacing the whole tool. Is the micrometer suitable for blind‑hole measurements? Designed specifically for blind‑hole (sackloch) inspection, the self‑centring three‑point design ensures reliable centring in such applications. What construction ensures long service life in the workshop? The MS908.666 uses carbide measuring faces and a robust analogue mechanism to withstand frequent use in industrial inspection environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of self‑centring three‑point measurement and carbide measuring faces for consistent, reproducible results in blind‑hole bores; the interchangeable measuring inserts allow flexible adaptation across the nominal range. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.668 — self‑centring, carbide faces (Metav IndustryLine) The MS908.668 is a three‑point internal micrometer for accurate measurement of blind‑hole bores in workshop and inspection environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Interchangeable measuring inserts Delivered in protective case Faster, repeatable centring in blind‑hole measurement The self‑centring three‑point measuring head significantly reduces setup time when inspecting blind‑hole bores. By contacting the bore with three equidistant measuring points the instrument centres itself automatically, which improves repeatability compared with two‑point probes and speeds up routine checks. The analogue mechanism keeps the operation straightforward for technicians and maintenance staff who require reliable results without complex electronics. Metrology performance you can rely on Designed for industrial use, the instrument offers a stated accuracy 0.007 mm and a resolution 0.005 mm, values that make it well suited for quality control in machining and assembly. These specifications mean the device detects small deviations while providing a clear mechanical indication of the measurement. The combination of robust mechanical gearing and a clear, fine graduation supports precise readings under standard workshop conditions, helping to maintain product tolerances and reduce the risk of costly rework. Durable contact surfaces and flexible inserts The measuring faces are carbide tipped to resist wear during frequent use, preserving the nominal geometry and ensuring long‑term stability. Interchangeable measuring inserts permit adaptation across the stated measuring span so one instrument can cover a range of bore diameters without compromising accuracy. Supplied in a protective case, the tool is ready for transport to the machine or for storage in an inspection cabinet, keeping the measuring faces protected between uses. Trusted partner for precision tasks As part of the Metav IndustryLine range, this three‑point internal micrometer benefits from the supplier’s focus on accessibility and reliability. Metav’s approach to precision brings workshop‑grade metrology within reach, backed by a broad product portfolio and proven logistical support from Emmerich. The instrument suits metrology labs, maintenance teams and production lines that prioritise consistent centring, wear resistance and straightforward operation. For expert advice or to purchase the Metav IndustryLine three‑point internal micrometer MS908.668 with interchangeable inserts and carbide faces, please contact Metav Werkzeuge for tailored assistance and fast supply Technical data Article number: MS908.668 Brand: Metav IndustryLine Category: Messschrauben Numbers / Facts Measuring range: 225–240 mm Resolution (reading): 0.005 mm Accuracy: 0.007 mm Length: 145 mm Analogue instrument Special features / Versions Self‑centring three‑point measuring head Carbide measuring faces Interchangeable measuring inserts Suitable for blind‑hole bores Supplied in protective case FAQ What measuring range does the instrument cover? The MS908.668 three‑point internal micrometer covers a measuring span from 225 mm to 240 mm as delivered. Is this tool suitable for blind‑hole measurements? Yes; the three‑point, self‑centring design is specifically intended for reliable measurement of blind‑hole bores. Can the measuring inserts be replaced to adjust for different bore sizes? Interchangeable measuring inserts are provided, allowing the instrument to be adapted across its nominal measuring span. How precise are the readings from this analogue instrument? The instrument provides a resolution of 0.005 mm with a stated accuracy of 0.007 mm, suitable for workshop and production quality checks. Are the measuring faces durable under regular workshop use? The contact points are carbide tipped to increase wear resistance and maintain geometric integrity over extended use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, self-centring three-point measuring head and 0.004 mm accuracy to inspect blind bores with confidence; the instrument’s fine graduations and carbide measuring faces ensure repeatable results in precision workshops. Order directly via Metav Werkzeuge or consult our specialists for application advice. Three-point internal micrometer MS908.651 — self-centring three-point head, 8.0–10.0 mm range (Metav IndustryLine) A three-point internal micrometer designed for precise measurement of blind bores in fine mechanical and workshop environments Self-centring three-point head Carbide measuring faces for durability 0.004 mm measurement accuracy 0.001 mm reading increment Precision engineered for blind-bore measurement The compact three-point design centres automatically on the bore, so alignment errors are reduced and repeatability improves for series checks. The instrument combines a finely graduated analogue spindle with a 0.001 mm reading increment and a verified measurement accuracy of 0.004 mm, which supports quality-controlled machining and inspection routines. This level of reproducibility is particularly valuable when measuring short, deep blind bores where radial run-out and offset would otherwise distort results. Durable contact surfaces and compact ergonomics for workshop use Carbide-tipped measuring faces give long service life under frequent contact and resist wear from abrasive contaminants, maintaining measurement integrity over time. The micrometer’s compact form — overall length 54.5 mm — places it in the micro class for instruments intended for extremely compact, fine‑mechanical tasks; the short, stiff geometry helps to keep handling-induced deflection to a minimum and is ideal for toolrooms, gauges and precision workshops where space and access are limited. Simple analogue operation that integrates with quality processes As an analogue instrument with a clear mechanical spindle, the device delivers tactile feedback and fast, direct readings that can speed up routine inspections without reliance on batteries or electronics. The self-centring action and carbide faces reduce setup time and scrap, while the fine reading increment enables informed pass/fail decisions at the bench. For traceable documentation, the micrometer’s technical values support incorporation into existing inspection protocols and measurement logs. Enquire with Metav Werkzeuge for tailored application advice or to procure the Metav IndustryLine three-point internal micrometer MS908.651 for precision blind‑bore inspection Technical data Article number: MS908.651 Type: Three-point internal micrometer Manufacturer: Metav IndustryLine Facts Measurement range: 8.0–10.0 mm Minimum range: 8.0 mm Maximum range: 10.0 mm Accuracy: ±0.004 mm Reading increment: 0.001 mm Length: 54.5 mm Special features Self-centring three-point head Carbide measuring faces Analogue operation Setting ring: 8 Suitable for blind bores FAQ What measurement range does the instrument cover? The MS908.651 covers a range of 8.0–10.0 mm for internal measurements. How precise is the three-point internal micrometer? The instrument provides a measurement accuracy of ±0.004 mm with a reading increment of 0.001 mm. Are the measuring faces wear-resistant? Yes, the measuring faces are carbide tipped to ensure long-term durability and consistent contact behaviour. Is the device suitable for routine workshop checks of blind bores? The three-point centring head and compact geometry make the MS908.651 well suited to routine blind-bore inspections in toolrooms and precision workshops. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com