How do I read the Bügelmessschraube correctly?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

The combination of precise self‑centring contact, a compact 10–12 mm measuring range and robust carbide faces ensures fast, repeatable blind‑hole measurements with minimal setup. Order the instrument directly via Metav Werkzeuge or consult the team for application advice. Metav IndustryLine Three‑Point Internal Micrometre MS908.652 — self‑centring, 10–12 mm range The Three‑Point Internal Micrometre MS908.652 is a compact analogue micrometre designed for precise diameter measurement inside blind holes and small bores in the 10–12 mm range. Self‑centring three‑point contact Measuring range 10–12 mm Accuracy 0.004 mm Carbide measuring faces Reliable centring for blind‑hole measurement A three‑point contact ensures rapid and reproducible alignment in blind holes, reducing repositioning time and measurement scatter. The micrometre’s self‑centring mechanism automatically locates the bore centre, so the operator obtains a consistent contact geometry on each measurement. With a measuring span of 10–12 mm the instrument is tailored to micro components and small bores where repeatability and short setup times are essential, improving throughput in small‑part inspection tasks. Durable contact surfaces for longer service life The measuring faces are manufactured as carbide contacts to resist wear and preserve accuracy during frequent use. The unit’s analogue design gives a tactile feel and straightforward reading, paired with a fine adjustment capability to approach tight fits carefully. The compact body (length approx. 54.5 mm) is suited to constrained access, while a setting ring (size 10) is included for verification and quick zeroing, supporting stable traceability in routine quality checks. Practical workflow advantages and workshop integration This three‑point micrometre combines simple operation with technical reliability: measurements are quick, calibration checks are straightforward and the tool integrates easily into existing inspection benches. Classified in the Micro range (max. 10–100 mm), it fulfils typical needs of precision engineering, watchmaking and small‑component production where stiffness, reach and single‑hand operation must be balanced. Metav’s distribution ensures European stock and reliable delivery from Emmerich. Request application guidance or order details from Metav Werkzeuge for the Metav IndustryLine three‑point internal micrometre MS908.652 — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.652 Brand: Metav IndustryLine Category: Micrometres Type: Three‑point internal micrometre Measuring range: 10.0–12.0 mm Minimum range: 10 mm Maximum range: 12 mm Accuracy: 0.004 mm Length: 54.5 mm Setting ring: 10 Self‑centring three‑point contact Carbide (hard metal) measuring faces Analogue operation (nonius style) Suitable for blind‑hole bores FAQ How does the three‑point contact improve measurement in blind holes? The three‑point geometry of the MS908.652 centres automatically in a bore, giving a stable contact triangle that reduces wobble and improves repeatability compared with single‑point probes. What measurement accuracy can be expected from this instrument? The instrument is specified with an accuracy of 0.004 mm; in routine use this delivers repeatable diameter readings for small‑bore inspection tasks. Is the micrometre suitable for workshop use or only for laboratory conditions? Designed for practical workshop use, the robust carbide faces and analogue adjustment make the MS908.652 resilient to frequent handling while keeping measurement quality high. How is the instrument returned to zero or checked on site? A setting ring (size 10) is provided for quick verification and zeroing of the micrometre before inspection runs. Which components and applications benefit most from this micrometre? Small bores, precision fittings, watch‑ and micro‑mechanical parts and any blind‑hole diameters in the 10–12 mm range benefit from the compact form, self‑centring contact and carbide faces of the MS908.652. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of high accuracy, wireless + USB data transfer and full ISO 17025 calibration with certificate for reliable measurements in precision workshops; order the three-point internal micrometre directly via Metav Werkzeuge or ask our consultants for tailored advice. Three‑Point Internal Micrometre – Digital internal measuring tool with wireless + USB and 1.5" colour touchscreen (Microtech Metrology) The Three‑Point Internal Micrometre is a compact digital instrument engineered for precise internal diameter measurement in small bores and precision components within the micro measurement category. *Digital display: 1.5" colour touchscreen *Wireless and USB data output *ISO 17025 calibrated with certificate *Measuring range 12–16 mm, 0.004 mm accuracy Accurate measurements for micro components Classified in the Micro category (suitable for very compact tasks), this instrument covers a measuring range of 12.0–16.0 mm, offering a practical reach for miniature assemblies and precision parts. The instrument combines a fine resolution of 0.0001 mm with a guaranteed accuracy of ±0.004 mm, which reduces measurement uncertainty and supports reproducible inspection results. Such precision is particularly valuable when inspecting small bores in sub‑assemblies where even slight deviations can affect fit and function. Traceable data capture and delivered calibration Designed for modern production environments, the micrometre provides wireless and USB connectivity for straightforward data transfer into inspection logs and SPC systems. The 1.5" colour touchscreen simplifies reading and setting adjustments on the shop floor, while the supplied setting ring ensures fast zeroing and repeatable reference points. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate, enabling formal traceability and immediate use in processes that require accredited measurement results. Ergonomic handling that speeds up inspections The three‑point contact design centres measurement force, improving contact consistency inside bores and reducing operator‑induced variation. The compact format supports single‑hand operation in confined spaces and the intuitive touchscreen speeds routine checks, lowering cycle times and decreasing the likelihood of rework. The included setting ring and clear digital readout combine to make daily inspection routines both ergonomic and efficient. Integration into workshop quality routines With its digital outputs and compact form factor, the device integrates easily into existing inspection stations and handheld workflows. The substantial measuring depth of 230 mm provides versatility when accessing deeper bores or assemblies, while the three‑point mechanism ensures stable centring for reliable interior measurements. Together, these features support a consistent quality chain from initial inspection through to final acceptance. Contact Metav Werkzeuge in Emmerich for a suitability review or to request a quotation for this Microtech Metrology three‑point internal micrometre with ISO 17025 calibration; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 133701610 GTIN: 4061905074219 Manufacturer: Microtech Metrology ECLASS: 21170335 Facts Measuring range: 12.0–16.0 mm Resolution: 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 230 mm Special features Digital colour 1.5" touchscreen Data output: Wireless and USB Included setting ring ISO 17025 calibration with certificate Three‑point internal measuring spindle FAQ What bore sizes can be inspected with this instrument? The Three‑Point Internal Micrometre is designed for bores in the 12.0–16.0 mm range and is classified in the micro category for compact internal measurements. Is the micrometre delivered calibrated for traceability? Yes, the instrument is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate traceable use. How are measurement results transferred to a PC or inspection system? Measurement data can be transmitted via the micrometre’s wireless interface or exported using the USB connection for integration into inspection logs. What level of precision can be expected during routine checks? Routine measurements with the Three‑Point Internal Micrometre offer a resolution of 0.0001 mm and an accuracy of ±0.004 mm, suitable for high‑precision shopfloor inspections. Does the tool include accessories for initial setup? The micrometre is supplied with an inclusive setting ring to establish a reproducible zero reference and support repeatable measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of compact design, repeatable self‑centring measurement and wear‑resistant carbide faces to maintain consistent bore quality in small components. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.653 — self‑centring three‑point head, carbide measuring faces (Metav IndustryLine) A Three‑point internal micrometer MS908.653 engineered for precise measurement of blind bores in workshop and quality‑control environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Precise range 12–16 mm with 0.004 mm accuracy Compact 80 mm body length for confined spaces Accurate measurements in confined bores The three‑point geometry provides a self‑centring effect that stabilises the measuring axis in blind holes, reducing eccentricity and improving repeatability. With a declared accuracy of 0.004 mm and a vernier reading increment of 0.005 mm, this analogue instrument delivers the fine mechanical resolution expected in micro‑component inspection. The design minimises operator variation by ensuring the measuring anvils expand symmetrically, which translates into faster decision‑making during incoming inspection or in‑process checks. Small format, specialist capability Classified in the Micro category (measuring range 12–16 mm), the tool combines a short 80 mm body length with a compact head that is easy to manoeuvre inside tight bores. The carbide measuring faces resist wear during repetitive use, extending the interval between maintenance cycles and preserving measurement integrity. An adjustment ring (size 16) allows repeatable pre‑settings for batch measurements, so set‑ups for small series or precision assemblies remain consistent without excessive rework. Built for blind‑hole tasks and straightforward handling Designed specifically for blind‑hole measurement, the three‑point micrometer eliminates the need for improvised measuring aids. Its analogue, non‑electronic construction favours robustness in workshop conditions and simplifies routine maintenance compared with electronic gauges. The combination of mechanical simplicity and the self‑centring head reduces measurement time and supports reliable dimensional control of bores used in bearings, housings and valve seats. Workshop integration and supplier confidence Metav IndustryLine supplies a practical measuring solution that fits established inspection routines and supports traceable quality processes. The instrument’s proven geometry and durable contact faces make it suitable for precision toolrooms and production lines where compact accuracy is required. For specification matching, calibration options and integration into existing quality workflows, Metav Werkzeuge acts as a single, reliable partner with rapid technical guidance and supply across Europe. Contact Metav Werkzeuge today for tailored technical advice and reliable supply of the MS908.653 three‑point internal micrometer via Metav Werkzeuge GmbH in Emmerich Technical data Article number: MS908.653 Brand: Metav IndustryLine Category: Messschrauben Facts Measuring range: 12.0–16.0 mm Measuring range (min): 12 mm Measuring range (max): 16 mm Body length: 80 mm Accuracy: 0.004 mm Reading increment: 0.005 mm Adjustment ring: 16 Special features Self‑centring three‑point head Carbide measuring faces Designed for blind‑hole measurement Analog/vernier design Compact micro‑class instrument FAQ What types of bores is this instrument intended for? This three‑point internal micrometer MS908.653 is designed for precise measurement of blind bores and internal diameters within its 12–16 mm range. How precise is the measurement and what resolution is readable? The instrument offers an accuracy of 0.004 mm with a vernier reading increment of 0.005 mm, providing fine mechanical resolution suitable for micro‑component inspection. Are the measuring faces durable for repetitive workshop use? Yes, the micrometer is fitted with carbide measuring faces to increase wear resistance during repetitive measurements and to maintain dimensional integrity. Is the micrometer suitable for small‑batch production set‑ups? Its compact 80 mm body and adjustment ring (size 16) enable repeatable pre‑settings, making the MS908.653 well suited to small series and frequent set‑ups. Can calibration or certification be arranged for this instrument? Calibration options and certificates can be arranged through Metav Werkzeuge; contact the supplier for available services and lead times. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a self‑centring three‑point measuring head and a 0.005 mm accuracy across a compact 50–63 mm range for reproducible blind‑bore inspections; order the instrument directly via Metav Werkzeuge or consult the specialists for application advice. Three‑point internal micrometer MS908.659 — Metav IndustryLine, self‑centring, 50–63 mm The Three‑point internal micrometer is a precision instrument designed for accurate measurement of blind bores and other internal diameters within the 50–63 mm range, combining a self‑centring three‑point head with robust analogue mechanics for repeatable results. Self‑centring three‑point measuring head Range 50–63 mm Accuracy 0.005 mm Carbide measuring faces Reproducible internal measurements through self‑centring design The instrument’s self‑centring three‑point measuring head converts small operator variations into consistent contact across the bore, which reduces eccentricity and minimises measurement scatter. With a declared accuracy of 0.005 mm and an analogue readout, this tool offers a clear, verifiable performance baseline that supports process control and reduces rework in production environments. The three‑point geometry is particularly effective on short to medium blind bores, where central alignment is critical to obtain reliable diameter values. Built for workshop use: durable faces and compact handling Equipped with carbide measuring faces, the device resists wear from regular contact with machined surfaces and maintains form integrity during frequent use. The compact overall length of 114 mm and a setting ring of 62 support comfortable handling in workshop and inspection‑bench situations, enabling efficient measurement cycles without sacrificing stiffness. As an analogue instrument, it delivers straightforward operation and low maintenance while providing the tactile feedback many technicians prefer for repeat measurements. Practical benefits for quality assurance and inspection routines Integrating this internal micrometer into quality checks provides a direct improvement to inspection throughput and measurement consistency. The tool is explicitly suitable for blind‑bore applications and mechanical assembly checks, offering a reliable technical solution where calipers or telescoping gauges may be less repeatable. The combination of a robust three‑point head and carbide contact faces translates into fewer measurement-related interruptions and a steadier conformity assessment across batches. Contact Metav Werkzeuge in Emmerich for tailored advice on application and availability of the MS908.659 three‑point internal micrometer Technical data Article number: MS908.659 Product: Three‑point internal micrometer Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 50–63 mm Minimum range: 50 mm Maximum range: 63 mm Reading / resolution: 0.005 mm Accuracy: 0.005 mm Length: 114 mm Setting ring: 62 Special features / Designs Self‑centring three‑point head Carbide (hard‑metal) measuring faces Analogue mechanical operation Suitable for blind bores FAQ What degree of accuracy can be expected from this three‑point internal micrometer? The MS908.659 from Metav IndustryLine delivers an accuracy of 0.005 mm with a 0.005 mm reading increment, suitable for precise workshop inspection tasks. Is this instrument suitable for blind‑bore measurement only? While optimised for blind bores, the three‑point internal micrometer is also applicable to other internal diameter checks where central alignment and repeatability are required. How does the self‑centring feature improve measurement results? The self‑centring three‑point head ensures even contact around the circumference, reducing eccentricity and enabling more reproducible diameter readings during routine inspections. What maintenance is recommended to retain measurement reliability? Regular cleaning of the carbide faces and periodic verification against a calibrated ring gauge will preserve the instrument’s performance; the analogue mechanics favour simple, on‑site care. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining self-centring operation with a guaranteed 0.005 mm accuracy across an 87–100 mm measuring band, this instrument delivers repeatable results for blind-hole inspection and internal-diameter checks. Order via Metav Werkzeuge or request expert advice from our consultants for application-specific guidance. Three-Point Internal Micrometer MS908.662 — Self-centring, 87–100 mm, 0.005 mm accuracy (Metav IndustryLine) A compact, three-point internal micrometer MS908.662 engineered for precise measurement of blind bores and internal diameters in the 87–100 mm range. Self-centring measuring head 87–100 mm measurement range 0.005 mm graduation and accuracy Carbide measuring faces for durability Precision for blind-hole measurements that must be repeatable The three-point measuring principle combines three symmetrically arranged anvils to centre automatically within the bore, reducing alignment errors and improving repeatability. With a declared accuracy of 0.005 mm and a matching reading resolution of 0.005 mm, the instrument is configured for reliable internal measurements where tight tolerances apply. The mechanical three-point arrangement compensates for minor irregularities in bore geometry and, compared with single-anvil probes, significantly reduces positional uncertainty; this is particularly important when inspecting blind bores where full insertion of contact probes is not possible. Durable, workshop-ready design for routine inspection Constructed with carbide measuring faces, the unit withstands abrasive and repetitive contact without rapid wear, thus maintaining measurement integrity over time. The analogue vernier operation provides a dependable mechanical reading method that does not rely on batteries, ensuring continuous availability on the shop floor. The compact overall length (114 mm) and a preset setting ring at 87 mm allow straightforward setup for the nominal range and make the tool suitable for tight-access tasks. These attributes combine to reduce downtime and simplify daily inspection routines in toolrooms and maintenance departments. Micro-class capability and typical use cases With a maximum measuring range of 100 mm, this instrument falls within the micro classification for compact internal gauges, a category valued for high precision in confined spaces. Typical applications include fine mechanical assembly, toolmaking, quality control of small to medium-sized components, and inspection of blind-hole bores in housings and castings. The self-centring function and carbide contacts make it an effective choice for repeated checks during production runs and for settings where consistent, operator-independent measurement behaviour is required. For tailored application advice or to secure this self-centring internal micrometer from Metav Werkzeuge in Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for consultancy and delivery options Technical Data Article number: MS908.662 Product: Three-point internal micrometer Brand: Metav IndustryLine Facts Measuring range: 87–100 mm Reading / Resolution: 0.005 mm Accuracy: 0.005 mm Overall length: 114 mm Setting ring: 87 mm Special features Self-centring three-point head Carbide measuring faces Analogue vernier operation Suitable for blind-hole bores FAQ Is this instrument suitable for measuring blind bores? Yes. The MS908.662 three-point internal micrometer from Metav IndustryLine is specifically designed for accurate measurement of blind-hole bores within the 87–100 mm band. What accuracy and resolution are provided? The tool offers a declared accuracy of 0.005 mm with a reading resolution of 0.005 mm, making it suitable for precise workshop inspection tasks. What are the measuring faces made from? The measuring faces are carbide-tipped to provide wear resistance and long-term dimensional stability under repeated use. Does the instrument require batteries or electronics? No. The device uses an analogue vernier principle and is entirely mechanical, eliminating the need for batteries and reducing maintenance points. For which workshop tasks is the micrometer best suited? Ideal for fine mechanical work, toolroom checks and production inspection of internal diameters and blind holes where compact, high-precision measuring tools are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com