How do you measure a micrometer?

Precision blind‑hole inspection is facilitated by the combination of a self‑centring three‑point head, carbide measuring faces and an accuracy of ±0.005 mm; order the MS908.663 via Metav Werkzeuge or consult our advisors for specification support. MS908.663 — three‑point internal micrometer with self‑centring head and ±0.005 mm accuracy (Metav IndustryLine) A self‑centring three‑point internal micrometer MS908.663 designed for fast, repeatable measurement of blind holes in workshop and production environments. Self‑centring three‑point measuring head Accuracy ±0.005 mm for repeatable results Carbide measuring faces for long service life Delivered in a protective transport case Precise blind‑hole measurement with minimal operator error The three‑point measuring concept produces a natural centre‑finding action that stabilises the instrument inside a blind hole, reducing eccentricity and operator influence. With an analogue reading of 0.005 mm and an accuracy of ±0.005 mm, this gauge is suited to quality‑critical internal diameter checks where small deviations matter. The vernier‑style scale enables direct mechanical reading without reliance on batteries or electronics, supporting uninterrupted inspections on the shop floor. This combination of mechanical reliability and fine resolution promotes consistent pass/fail decisions during incoming inspection and first‑off checks. Built for demanding workshop use and long‑term repeatability Constructed with carbide measuring faces, the instrument resists wear in daily use and preserves measuring integrity over longer service intervals. The instrument’s physical length of 145 mm and measuring span of 100–125 mm places it in the standard measuring range for general machine‑shop applications, offering a practical balance between reach and rigidity. The robust design and hardened contact surfaces make the micrometer tolerant of routine handling; the supplied protective transport case reduces the risk of damage during storage and transit, keeping calibration stability intact. Practical advantages for process control and inspection routines Using a self‑centring, three‑point internal gauge streamlines internal diameter checks in blind holes, bores and recesses, enabling faster set‑ups at the bench or on the machine. The instrument’s repeatable seating and fine resolution help to reduce scrap and rework by catching dimensional drift earlier in the process. As an analogue instrument it integrates easily into established measurement routines and inspection sheets, while its mechanical simplicity minimises downtime compared with devices that rely on electronics. Typical applications and handling guidance The micrometer is intended for blind‑hole and internal diameter measurements in general engineering, toolroom checks and production quality control. For best results, ensure clean contact surfaces and a stable seating in the bore before taking a reading; the three‑point head will centre itself, but careful alignment reduces measurement scatter. Periodic verification against a gauge block or master ring is recommended to confirm ongoing accuracy and to schedule recalibration when necessary. The instrument’s durability and simple operation make it a practical choice for repetitive internal measurements on ferrous and non‑ferrous components. For reliable blind‑hole inspection with Metav IndustryLine precision, contact Metav Werkzeuge for purchase and expert advice by email at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical data Article number: MS908.663 Name: Three‑point internal micrometer Brand: Metav IndustryLine Type: Analogue internal measuring instrument Numbers / Core technical data Measuring range: 100–125 mm Measuring length: 145 mm Reading / Resolution: 0.005 mm Accuracy: ±0.005 mm Special features / Design Self‑centring three‑point measuring head Carbide measuring faces Delivered in a protective transport case Suitable for blind‑hole (blind bore) measurement FAQ How does the three‑point head help with blind‑hole measurement? The three‑point geometry of the MS908.663 automatically centres inside a blind hole, reducing eccentricity and improving repeatability of internal diameter readings. What level of accuracy and resolution can be expected? The instrument provides a resolution of 0.005 mm with an accuracy of ±0.005 mm, making it suitable for tight tolerance internal checks in production and workshop environments. Is the gauge suitable for frequent workshop use? Yes; the carbide measuring faces and robust mechanical construction are designed for daily inspection tasks and extended service life. Can this micrometer measure other internal features besides blind holes? While optimised for blind holes, the instrument can be used for internal diameter checks, recesses and similar internal features where the three‑point contact can seat reliably. What is included with the instrument on delivery? The MS908.663 is supplied complete with a protective transport case to protect the gauge during storage and transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of self-centring three-point contact, hardened measuring faces and a protective case for reliable, repeatable blind-bore measurement; order directly via Metav Werkzeuge or request advice from our technical consultants. Three-point internal micrometer MS908.664 — self-centring design, 125–150 mm (Metav IndustryLine) The Three-point internal micrometer MS908.664 is a precision instrument for accurate measurement of blind bores and internal diameters in machine shops and inspection benches Self-centring three-point contact Accuracy ±0.005 mm Hardened measuring faces Supplied in protective case Consistent concentric measurement where it matters The instrument’s self-centring three-point contact mechanism converts small radial differences into a single, centred datum, ensuring high repeatability during blind-bore checks. With a mechanical resolution and accuracy of ±0.005 mm, the device supports tight tolerance verification and process control for internal diameters. This level of precision is particularly useful when comparing series parts or validating internal fits, as the three-point geometry minimises eccentricity and reduces operator-induced variation. Robust construction for repetitive workshop use A durable construction and hardened measuring faces protect the contact points from wear and maintain measurement integrity over prolonged use. The analogue, mechanical drive reduces complexity and avoids battery dependence, making the tool suitable for routine quality inspections on the shop floor. The overall length of 145 mm gives the reach required for its measurement range while keeping the instrument compact enough for stable handling during repeated checks. Ideal balance of reach and stiffness for standard applications Classified in the standard range for internal measurement instruments (125–150 mm), this micrometer offers the best compromise between measuring reach and structural rigidity. That balance is critical in metalworking and fixture assembly, where longer tools can introduce deflection and shorter tools lack coverage. The design is optimised for blind bores, providing reliable access and reproducible contact even when full through-access is not available. Delivered protected and ready for transport The instrument is supplied in a protective case to safeguard measuring faces and the mechanism during transport and storage. Built for regular inspection cycles, it integrates easily into workshop tool sets and measurement benches; its analogue readout is simple to interpret and maintain, supporting efficient quality routines without complex electronic calibration procedures. Contact Metav Werkzeuge for tailored advice on the Metav IndustryLine three-point internal micrometer MS908.664 and to arrange procurement or technical specification support; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.664 Manufacturer: Metav IndustryLine Type: Three-point internal micrometer Feature: Self-centring Measuring range: 125–150 mm Length: 145 mm Accuracy: 0.005 mm Reading: 0.005 mm Mechanism: Analogue Delivery: protective case Measuring faces: hardened Suitable for: blind bores Numeric data Measurement range: 125–150 mm Maximum measurement: 150 mm Minimum measurement: 125 mm Accuracy/resolution: 0.005 mm Length: 145 mm SKU: MS908.664 Design and special features Self-centring three-point contact Hardened measuring faces for wear resistance Analogue drive for low maintenance Compact length for stable handling Supplied in protective case for transport Intended for blind-bore measurement FAQ What measurement range does the instrument cover? The instrument covers a measurement range of 125–150 mm, placing it in the standard workshop range suitable for many machine‑building and metalworking applications; refer to MS908.664 for exact limits. What accuracy and resolution are specified? The device offers an accuracy and reading resolution of 0.005 mm, enabling reliable checks against typical tight tolerance requirements. Is the design suitable for blind bores? Yes — the self-centring three-point contact is engineered specifically to measure blind bores with improved concentricity and repeatability. Are the measuring faces wear-resistant? The measuring faces are hardened to resist wear and maintain consistent contact geometry during repetitive inspection tasks. Is a protective case included? The instrument is supplied in a protective case to secure the micrometer during transport and storage. Is the micrometer digital or analogue? This is an analogue instrument with a mechanical drive and a direct, tactile measuring feel appropriate for workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of self‑centring, carbide measuring faces and high repeatability for reliable blind‑hole inspection; the compact 20–25 mm range is ideal for fine mechanical and precision engineering tasks. Order the instrument directly via Metav Werkzeuge or request specification advice from our consultants. Three‑point internal micrometer MS908.655 — self‑centring, carbide measuring faces (20–25 mm) by Metav IndustryLine The Three‑point internal micrometer MS908.655 is a self‑centring internal measuring instrument designed for accurate measurement of blind holes in precision engineering and workshop environments, offering an analogue reading with fine resolution for repeatable results Self‑centring three‑point mechanism Carbide measuring faces for wear resistance Measurement accuracy 0.004 mm Compact range 20–25 mm for fine parts Precise blind‑hole measurement with minimal setup The instrument delivers high repeatability through its self‑centring three‑point mechanism, which ensures concentric contact inside blind bores without complex alignment. With a rated accuracy of 0.004 mm and an analogue reading of 0.005 mm, the device is engineered for tasks where micrometre‑level certainty matters; this combination reduces rework and measurement uncertainty in small components. The compact design is especially suited to micro fabrication and precision inspection of housings and bores. Durable contact faces and dependable mechanical operation Carbide contact faces provide excellent wear resistance, maintaining measurement integrity over extended use in workshop conditions. The analogue nonius construction offers tactile feedback preferred in many inspection routines and requires no batteries or electronic interfaces, supporting uninterrupted operation on the shop floor. The included adjustment ring (25) enables straightforward zeroing and fine setting, while the robust build keeps the mechanical play to a minimum for consistent results. Designed for micro‑range quality control and fine parts Classified in the micro range (suitable for 10–100 mm scales), the 20–25 mm span targets small‑format parts such as precision sleeves, bearing bores and microassemblies. Its compact dimensions and precise geometry make it practical for use in bench inspection and in‑process checks where access is restricted. The measuring faces and frame geometry have been selected to balance stiffness and accessibility, ensuring stable measurements even when handling delicate components. Integration into workshop procedures and traceability The analogue three‑point gauge complements digital and traditional inspection tools as part of a consistent metrology chain; repeatable manual results simplify tolerance checks and go/no‑go decisions. Further technical documentation and measurement data are available from Metav Werkzeuge for integration into QA processes and production control. For operators transitioning from standard calipers or bore gauges, the instrument provides a clear step up in concentricity control without introducing complex electronics. For specification advice or to secure the MS908.655 from Metav IndustryLine, contact Metav Werkzeuge for personalised guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.655 Manufacturer: Metav IndustryLine Product: Three‑point internal micrometer Numbers / Core technical data Measuring range: 20–25 mm Reading / resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features / Materials Self‑centring three‑point mechanism Carbide measuring faces Analogue nonius scale Suitable for blind‑hole measurement FAQ What measuring range does the MS908.655 cover? The MS908.655 covers a measuring range of 20–25 mm, making it suitable for small bores and fine mechanical components. How precise is the instrument for repeatable checks? The three‑point internal micrometer achieves a stated accuracy of 0.004 mm with an analogue reading of 0.005 mm, designed for consistent bench and in‑process inspection. Are the measuring faces wear resistant? Yes, the contact faces are made of carbide, providing enhanced wear resistance and long‑term dimensional stability for routine use. Is the gauge suitable for blind‑hole applications? The instrument is explicitly intended for blind‑hole measurement, featuring a self‑centring mechanism that ensures concentric contact within such bores. Does Metav IndustryLine provide technical support for integration into QA procedures? Metav IndustryLine and Metav Werkzeuge can supply further technical documentation and advice to assist with integration of the MS908.655 into quality control workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the self-centring three-point system and interchangeable measuring insert for reliable blind-hole measurements; combined with carbide measuring faces and an accuracy of ±0.007 mm, this instrument supports consistent quality control. Order the (three-point internal micrometer MS908.667) directly via (Metav Werkzeuge) or ask our consultants if needed. Three-point internal micrometer MS908.667 — self-centring, interchangeable insert The three-point internal micrometer for precise measurement of blind bores in workshop and inspection environments, designed as a mechanical instrument for repeatable internal diameter checks. Self-centring three-point system Interchangeable measuring insert Carbide measuring faces for wear resistance High precision ±0.007 mm Reliable blind-bore measurement with minimal operator influence The three-point system centres automatically within blind bores, reducing alignment errors and giving a reproducible contact geometry; this produces consistent results when inspecting bores. With a reading resolution of 0.005 mm (vernier) and a stated accuracy of ±0.007 mm, the instrument narrows measurement uncertainty to a level suitable for many workshop and production control tasks. The effect is a measurable reduction in rework and faster go/no-go decisions on turning and drilling operations. Durable contact surfaces and easy servicing save time Hard-wearing carbide measuring faces extend service intervals and maintain measurement integrity under repeated use. The measuring insert is exchangeable, which simplifies maintenance and allows quick replacement of worn contacts without discarding the whole instrument. The mechanical construction is straightforward and low-maintenance compared with electronic systems, making it suitable for environments where robustness and simple servicing are priorities. Size and handling tuned to everyday workshop needs Classified in the standard measuring range (measuring range 200–225 mm), this device offers a practical balance of reach and stiffness for typical machine‑shop components such as housings, sleeves and medium-sized bores. The instrument’s overall length of 145 mm supports good accessibility in confined bores while remaining easy to handle during repeated checks. As an analogue instrument with a vernier readout, it performs reliably where electronic readouts are unnecessary or undesired. Confidence for quality control and process stability Intended for routine inspection and in-process checks, the micrometer’s self-centring action and robust contact faces reduce operator-dependent variation and increase throughput in batch inspection. The interchangeable insert concept supports lifecycle planning: wear parts can be stocked and replaced quickly to maintain traceable measurement performance. The device is suitable for blind-hole measurement tasks and integrates well into manual quality-control workflows where mechanical verifiability is required. Contact Metav Werkzeuge today for ordering details and specification advice on the Metav IndustryLine three-point internal micrometer MS908.667 and its spare measuring inserts Technical Data Article number: MS908.667 Manufacturer: Metav IndustryLine Category: Micrometers (internal micrometer) Facts Measuring range: 200–225 mm Reading / Resolution: 0.005 mm Accuracy: ±0.007 mm Overall length: 145 mm Display: analogue (vernier) Features & Delivery Self-centring three-point system Carbide measuring faces Interchangeable measuring insert Designed for blind bores (blind-hole measurement) Mechanical, analogue instrument FAQ How does the three-point centring reduce measurement error? The self-centring three-point mechanism distributes contact forces evenly; the three-point internal micrometer MS908.667 centres itself in the bore to reduce eccentricity and improve repeatability. Can the measuring faces be replaced when worn? Yes — the instrument is fitted with an exchangeable measuring insert, so worn carbide faces can be renewed without replacing the entire micrometer. Is the reading digital or mechanical? The device uses a mechanical vernier readout with a reading resolution of 0.005 mm, offering a robust, electronics-free solution for workshop environments. For which bore types is this instrument intended? It is designed specifically for blind bores; the three-point configuration ensures reliable contact geometry in such applications. What is the measuring range and typical accuracy? The measuring range is 200–225 mm and the stated accuracy is ±0.007 mm, suitable for standard workshop inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of self‑centring three‑point contact, 0.005 mm accuracy and carbide measuring faces to secure reproducible blind‑hole measurements; order the MS908.658 directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.658 — self‑centring, 40–50 mm range (Metav IndustryLine) The Three‑point internal micrometer MS908.658 is a self‑centring, analogue instrument intended for precision measurement of blind holes and internal bores in small to medium components, offering a compact solution for fine mechanical and toolmaking tasks. Self‑centring three‑point measurement High precision: 0.005 mm accuracy Carbide measuring faces for durability Measuring range 40–50 mm for blind holes Reliable accuracy for critical fits and assemblies The MS908.658 delivers a resolution of 0.005 mm with a matching accuracy of 0.005 mm, providing measurable repeatability for tolerance‑sensitive internal features. The finely graduated analogue scale suits production and workshop environments where a tactile, immediate reading is preferred over electronic systems. This level of precision reduces rework and inspection time by supplying a clear, verifiable measurement result that supports quality control routines and efficient process decisions. Compact, micro‑range design that reduces handling error Classified in the micro range (max. 10–100 mm), the instrument’s 40–50 mm span targets finely detailed components such as small housings, inserts and precision sleeves. The self‑centring mechanism with three‑point contact automatically aligns the measuring faces within a bore, lowering sensitivity to off‑axis entry and operator variance. The compact form factor and balanced length make single‑handed operation straightforward, improving throughput where frequent in‑process checks are required. Durable measuring faces for long‑term repeatability Equipped with carbide (hardmetal) measuring faces, the micrometer resists wear and maintains measurement integrity across extended use. Carbide tips provide a hard, stable contact surface that minimises surface damage to workpieces while preserving repeatable reference points. For workshops seeking a robust, low‑maintenance gauge, this construction ensures a consistent lifecycle performance and contributes to lower total cost of ownership over time. Practical handling, calibration and typical applications The instrument is analogue and supplied with a setting ring at 40 mm to simplify zeroing and quick verification before series checks. Its total length of 97 mm facilitates access to compact bores while keeping the device rigid during measurement. Typical applications include blind‑hole inspection in toolmaking, component verification in precision engineering and quick fit checks in assembly processes. For specification matching and integration into inspection routines, Metav’s product consultants can assist with selection and measuring technique recommendations. Choose the Metav IndustryLine MS908.658 for reproducible blind‑hole measurement and contact Metav Werkzeuge in Emmerich for tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: MS908.658 Type: Three‑point internal micrometer Brand: Metav IndustryLine Measuring range: 40–50 mm Resolution / reading: 0.005 mm Accuracy: 0.005 mm Operation: Analogue Setting ring: 40 Length: 97 mm Facts Measuring range: 40–50 mm Resolution: 0.005 mm Accuracy: ±0.005 mm Length: 97 mm Special features Self‑centring mechanism Three‑point contact for blind‑hole measurement Carbide (hardmetal) measuring faces Suited for fine mechanical and toolmaking applications Analogue scale for immediate readings FAQ What bore sizes can be measured with this instrument? The MS908.658 covers internal dimensions in the 40–50 mm range and is optimised for blind‑hole measurement within that span. How precise is the measurement capability? The instrument offers a resolution of 0.005 mm with an accuracy rated at 0.005 mm, suitable for many tolerance‑sensitive internal checks. Are the measuring faces wear‑resistant? Yes, the MS908.658 is fitted with carbide (hardmetal) measuring faces, which provide superior wear resistance and long‑term repeatability. Is this gauge suitable for production‑line checks? Its compact, analogue design and self‑centring three‑point system make the micrometer well suited to repetitive in‑process inspections and quick verification tasks. Does the micrometer require electronic data output? This model is analogue and does not include electronic data output; it is designed for direct, fast readings on the shop floor. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise three-point contact, a self-centring mechanism and an accuracy of 0.005 mm for reliable blind‑hole measurement; order the MS908.661 directly via Metav Werkzeuge or ask our consultants for application advice. Three‑point internal micrometer MS908.661 — 75–88 mm range, self‑centring (Metav IndustryLine) The Three‑point internal micrometer MS908.661 offers a compact, mechanically robust solution for accurate measurement of blind bores between 75 and 88 mm, combining repeatable contact geometry with workshop‑grade durability. Self‑centring three‑point contact Measuring range 75–88 mm Accuracy 0.005 mm Precise three‑point geometry for repeatable blind‑hole results The instrument employs a three‑point contact arrangement that engages the bore at equidistant positions, producing consistent centring and minimising eccentricity in blind‑hole measurements. With a specified accuracy of 0.005 mm and a reading increment of 0.005 mm, the mechanical design prioritises repeatability and straightforward interpretation of results. This focus on measurable performance supports quicker decision‑making on the shop floor and reduces the likelihood of rework caused by inconsistent bore centring. Robust construction and easy handling for daily use Built for persistent use in production and inspection areas, the gauge features hardened measuring faces and an analogue measuring mechanism that requires no batteries. The compact body (length 114 mm) and an adjustable setting ring (87) provide tactile control during measurement operations. Hardened contact surfaces extend service life under typical workshop conditions, while the analogue format keeps the instrument immediately usable without electronic maintenance. The combined effect is low‑maintenance operation with dependable mechanical accuracy. Practical suitability and workflow benefits Designed specifically for blind‑hole applications, the tool is suited to toolrooms, maintenance shops and quality control benches where internal diameters must be checked quickly and reliably. The self‑centring action reduces setup time and helps standardise measurement procedures across operators, improving throughput and traceability. As a purely mechanical gauge it integrates easily with established inspection routines and supports rapid pass/fail decisions without additional calibration steps beyond routine verification. Quality assurance and provenance that support procurement Supplied under the Metav IndustryLine umbrella, the instrument represents a balance of functional precision and workshop pragmatism. Choice of a mechanically driven, three‑point internal gauge is a rational investment when repeatability and simple operation are priorities. Metav’s approach to product selection and distribution provides transparency and supply reliability for industrial buyers who prioritise consistent measurement outcomes. For technical availability and procurement of the MS908.661 three‑point internal micrometer, contact Metav Werkzeuge for product guidance and stock information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: MS908.661 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Core specifications Measuring range: 75–88 mm Accuracy: 0.005 mm Reading increment: 0.005 mm Length: 114 mm Setting ring: 87 Special features Self‑centring three‑point contact Hardened measuring faces Analogue measuring mechanism Suitable for blind‑hole bores Category: Micrometers FAQ What measuring range does this instrument cover? The MS908.661 covers a measuring range of 75–88 mm and is therefore suited to medium‑sized internal diameters such as blind bores in assemblies. How precise is the measurement? Precision is stated as 0.005 mm with a reading increment of 0.005 mm, which ensures repeatable results for standard workshop inspection tasks. Why is three‑point contact advantageous for blind holes? Three‑point contact centres the gauge automatically within the bore, reducing eccentricity and improving repeatability compared with single‑point internal probes. Where is this instrument typically used? This analogue internal micrometer is used in toolrooms, maintenance workshops and quality control where robust, battery‑free measurement of blind bores is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com