How much does a micrometer cost?

Take advantage of the combination of precise three-point measurement, wireless data output with USB, and full ISO 17025 calibration for dependable bore inspection and traceable results; order via Metav Werkzeuge or consult the specialists for application advice. Three-point internal micrometer — digital, 100–150 mm measuring range, Wireless + USB, Microtech Metrology The Three-point internal micrometer is a digital, workshop-ready instrument for repeatable bore and internal diameter checks from 100 to 150 mm, designed for production quality control and laboratory verification. ISO 17025 calibration certificate included Wireless and USB data output Colour 1.5" touchscreen display High repeatability: 0.004 mm accuracy Reliable measurement where it matters The instrument delivers consistent three-point measurement across bores, reducing orientation error and improving repeatability compared with single-point probes. With a specified accuracy of ±0.004 mm, the device supports quality control procedures that demand tight tolerances. The standard-sized measuring range classifies the tool for typical workshop and machine‑shop applications, offering a practical balance between reach and rigidity for medium-sized components. Fast data capture and traceability for production Equipped with Wireless and USB data outputs and a Colour 1.5" touchscreen, the device streamlines data acquisition and logging without manual transcription. The high-resolution reading (0.0001 mm) ensures fine increments are visible on the display, while digital output supports integration into measurement software or SPC workflows. This lowers administrative effort and helps maintain a clear audit trail for batch releases. Practical handling that reduces operator influence The included adjustment ring simplifies zeroing and routine checks, and the three-contact measuring head minimises tilting errors during insertion into bores. A measuring depth of 250 mm allows access to deeper cavities while preserving stability. These ergonomic and mechanical details reduce the effect of operator technique on the measurement result, improving reproducibility across shifts. Certified delivery and industrial readiness This micrometer is supplied fully calibrated to ISO 17025 standards and includes a calibration certificate, making it immediately suitable for accredited quality environments. The combination of high accuracy, digital interfacing and certified calibration positions the instrument as a reliable tool for incoming inspection, in‑process checks and final acceptance testing. Contact Metav Werkzeuge for tailored advice and secure a certified Microtech Metrology three-point internal micrometer (SKU 133715010) with ISO 17025 calibration for your measurement process Technical data Article number: 133715010 GTIN: 4061905074295 Manufacturer: Microtech Metrology ECLASS: 21170335 ETIM: EC003590 Facts Measuring range: 100–150 mm Resolution (reading): 0.0001 mm Accuracy: ±0.004 mm Measuring depth: 250 mm Digital display: Colour 1.5" touchscreen Data output: Wireless + USB Calibration: ISO 17025 certificate included Special features Three-point internal measurement Adjustment ring included Digital operation for SPC integration Suitable for workshop and lab use Delivered calibrated for traceability FAQ Is this instrument supplied calibrated? Yes. The Microtech Metrology three-point internal micrometer (SKU 133715010) is delivered fully calibrated to ISO 17025 and includes the corresponding calibration certificate. Which measurement range does the instrument cover? The device covers a measuring range of 100–150 mm, which places it in the standard class for workshop and machine‑shop bore inspection tasks. How are measurement results exported? Measurement data can be exported either wirelessly or via USB, enabling direct transfer into inspection software or SPC systems from the Microtech Metrology instrument. What resolution and accuracy can be expected? The display resolution is 0.0001 mm and the specified accuracy is ±0.004 mm, suitable for stringent dimensional checks in production control. Is the touchscreen suitable for use with gloves? The 1.5" colour touchscreen provides clear readout and simple menus; for glove operation, common shop gloves may limit sensitivity—repeatable results are maintained via the device’s stable mechanical design. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Benefit from the combination of three-point contact stability, a colour touchscreen readout and ISO 17025 traceable calibration to secure reproducible internal measurements in the 10.0–12.0 mm range. Order the Three‑Point Internal Micrometer directly via Metav Werkzeuge or consult our specialists for integration advice. Three‑Point Internal Micrometer — digital instrument with Wireless + USB (Microtech Metrology) The Three‑Point Internal Micrometer is a precision instrument for stable internal diameter measurement in small bores, suitable for quality control and bench metrology in workshops and production. Three-point contact for stable internal measurements Colour 1.5" touchscreen for clear readouts Wireless and USB data output for traceable transfer Delivered calibrated to ISO 17025 with certificate Dependable accuracy where tight tolerances matter The instrument combines a three-point contact measuring head with a high‑precision mechanism to reduce runout and centring error, delivering an accuracy of ±0.004 mm across its measuring span. With a measuring range of 10.0–12.0 mm, this device is aimed at fine internal dimensions where repeatability and a low measurement uncertainty are decisive. The robust contact geometry and confirmed specification make it well suited to small‑bore inspection tasks in component finishing and final inspection workflows, supporting a rational decision process for integrating metrology into production control. Seamless data capture for quality documentation Digital measurement is presented on a Colour 1.5" touchscreen for fast reading and reduced interpretation errors; the unit also provides Wireless and USB data output for direct transfer into SPC systems or inspection software. Combined with the included calibration trace, this workflow supports rapid documentation and traceability. The instrument’s readable display and straightforward data export reduce process steps and the risk of transcription mistakes, promoting efficiency and error‑resilient quality reporting in serial inspection and laboratory environments. Practical design for everyday workshop use A compact measuring head with an extended measuring depth of 154 mm keeps handling comfortable while reaching into bores and recesses. A setting ring is included to simplify zeroing and periodic checks. Delivered fully calibrated to ISO 17025, the micrometer arrives with a formal calibration certificate, providing immediate confidence for compliance audits and internal quality routines. The combination of robust measuring geometry, clear digital feedback and certified calibration supports both operational ease and trustworthy results, reinforcing productive workflows and peace of mind in routine inspections. For traceable high‑precision internal measurement solutions from Microtech Metrology, contact Metav Werkzeuge for ordering and application support — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 133701210 GTIN: 4061905074202 Manufacturer: Microtech Metrology Numbers Measuring range: 10.0–12.0 mm Measuring depth: 154 mm Accuracy: ±0.004 mm Resolution/readout: 0.0001 mm Special features Digital display: Colour 1.5" touchscreen Data output: Wireless and USB Setting ring: included Delivered calibrated to ISO 17025 with certificate FAQ Is the instrument delivered with a calibration certificate? Yes. The Three‑Point Internal Micrometer from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the calibration certificate for traceability. What measurement range is covered by this micrometer? The device covers internal diameters from 10.0 to 12.0 mm and is designed specifically for high‑precision work within that span. How is measured data transferred to a PC or quality system? Measurement results can be exported via both Wireless and USB connections, enabling straightforward integration into inspection software and SPC workflows. What advantage does the three‑point contact offer? Three contact points centre in the bore automatically, reducing eccentricity and improving repeatability compared with two‑point methods, which is why this geometry is preferred for small‑bore internal measurements. Can the micrometer reach recessed bores? Yes. The instrument’s 154 mm measuring depth allows access to deeper internal features while maintaining the necessary measurement stability. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools

Take advantage of the combination of compact design, repeatable self‑centring measurement and wear‑resistant carbide faces to maintain consistent bore quality in small components. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.653 — self‑centring three‑point head, carbide measuring faces (Metav IndustryLine) A Three‑point internal micrometer MS908.653 engineered for precise measurement of blind bores in workshop and quality‑control environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Precise range 12–16 mm with 0.004 mm accuracy Compact 80 mm body length for confined spaces Accurate measurements in confined bores The three‑point geometry provides a self‑centring effect that stabilises the measuring axis in blind holes, reducing eccentricity and improving repeatability. With a declared accuracy of 0.004 mm and a vernier reading increment of 0.005 mm, this analogue instrument delivers the fine mechanical resolution expected in micro‑component inspection. The design minimises operator variation by ensuring the measuring anvils expand symmetrically, which translates into faster decision‑making during incoming inspection or in‑process checks. Small format, specialist capability Classified in the Micro category (measuring range 12–16 mm), the tool combines a short 80 mm body length with a compact head that is easy to manoeuvre inside tight bores. The carbide measuring faces resist wear during repetitive use, extending the interval between maintenance cycles and preserving measurement integrity. An adjustment ring (size 16) allows repeatable pre‑settings for batch measurements, so set‑ups for small series or precision assemblies remain consistent without excessive rework. Built for blind‑hole tasks and straightforward handling Designed specifically for blind‑hole measurement, the three‑point micrometer eliminates the need for improvised measuring aids. Its analogue, non‑electronic construction favours robustness in workshop conditions and simplifies routine maintenance compared with electronic gauges. The combination of mechanical simplicity and the self‑centring head reduces measurement time and supports reliable dimensional control of bores used in bearings, housings and valve seats. Workshop integration and supplier confidence Metav IndustryLine supplies a practical measuring solution that fits established inspection routines and supports traceable quality processes. The instrument’s proven geometry and durable contact faces make it suitable for precision toolrooms and production lines where compact accuracy is required. For specification matching, calibration options and integration into existing quality workflows, Metav Werkzeuge acts as a single, reliable partner with rapid technical guidance and supply across Europe. Contact Metav Werkzeuge today for tailored technical advice and reliable supply of the MS908.653 three‑point internal micrometer via Metav Werkzeuge GmbH in Emmerich Technical data Article number: MS908.653 Brand: Metav IndustryLine Category: Messschrauben Facts Measuring range: 12.0–16.0 mm Measuring range (min): 12 mm Measuring range (max): 16 mm Body length: 80 mm Accuracy: 0.004 mm Reading increment: 0.005 mm Adjustment ring: 16 Special features Self‑centring three‑point head Carbide measuring faces Designed for blind‑hole measurement Analog/vernier design Compact micro‑class instrument FAQ What types of bores is this instrument intended for? This three‑point internal micrometer MS908.653 is designed for precise measurement of blind bores and internal diameters within its 12–16 mm range. How precise is the measurement and what resolution is readable? The instrument offers an accuracy of 0.004 mm with a vernier reading increment of 0.005 mm, providing fine mechanical resolution suitable for micro‑component inspection. Are the measuring faces durable for repetitive workshop use? Yes, the micrometer is fitted with carbide measuring faces to increase wear resistance during repetitive measurements and to maintain dimensional integrity. Is the micrometer suitable for small‑batch production set‑ups? Its compact 80 mm body and adjustment ring (size 16) enable repeatable pre‑settings, making the MS908.653 well suited to small series and frequent set‑ups. Can calibration or certification be arranged for this instrument? Calibration options and certificates can be arranged through Metav Werkzeuge; contact the supplier for available services and lead times. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of self‑centring, carbide measuring faces and high repeatability for reliable blind‑hole inspection; the compact 20–25 mm range is ideal for fine mechanical and precision engineering tasks. Order the instrument directly via Metav Werkzeuge or request specification advice from our consultants. Three‑point internal micrometer MS908.655 — self‑centring, carbide measuring faces (20–25 mm) by Metav IndustryLine The Three‑point internal micrometer MS908.655 is a self‑centring internal measuring instrument designed for accurate measurement of blind holes in precision engineering and workshop environments, offering an analogue reading with fine resolution for repeatable results Self‑centring three‑point mechanism Carbide measuring faces for wear resistance Measurement accuracy 0.004 mm Compact range 20–25 mm for fine parts Precise blind‑hole measurement with minimal setup The instrument delivers high repeatability through its self‑centring three‑point mechanism, which ensures concentric contact inside blind bores without complex alignment. With a rated accuracy of 0.004 mm and an analogue reading of 0.005 mm, the device is engineered for tasks where micrometre‑level certainty matters; this combination reduces rework and measurement uncertainty in small components. The compact design is especially suited to micro fabrication and precision inspection of housings and bores. Durable contact faces and dependable mechanical operation Carbide contact faces provide excellent wear resistance, maintaining measurement integrity over extended use in workshop conditions. The analogue nonius construction offers tactile feedback preferred in many inspection routines and requires no batteries or electronic interfaces, supporting uninterrupted operation on the shop floor. The included adjustment ring (25) enables straightforward zeroing and fine setting, while the robust build keeps the mechanical play to a minimum for consistent results. Designed for micro‑range quality control and fine parts Classified in the micro range (suitable for 10–100 mm scales), the 20–25 mm span targets small‑format parts such as precision sleeves, bearing bores and microassemblies. Its compact dimensions and precise geometry make it practical for use in bench inspection and in‑process checks where access is restricted. The measuring faces and frame geometry have been selected to balance stiffness and accessibility, ensuring stable measurements even when handling delicate components. Integration into workshop procedures and traceability The analogue three‑point gauge complements digital and traditional inspection tools as part of a consistent metrology chain; repeatable manual results simplify tolerance checks and go/no‑go decisions. Further technical documentation and measurement data are available from Metav Werkzeuge for integration into QA processes and production control. For operators transitioning from standard calipers or bore gauges, the instrument provides a clear step up in concentricity control without introducing complex electronics. For specification advice or to secure the MS908.655 from Metav IndustryLine, contact Metav Werkzeuge for personalised guidance at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: MS908.655 Manufacturer: Metav IndustryLine Product: Three‑point internal micrometer Numbers / Core technical data Measuring range: 20–25 mm Reading / resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features / Materials Self‑centring three‑point mechanism Carbide measuring faces Analogue nonius scale Suitable for blind‑hole measurement FAQ What measuring range does the MS908.655 cover? The MS908.655 covers a measuring range of 20–25 mm, making it suitable for small bores and fine mechanical components. How precise is the instrument for repeatable checks? The three‑point internal micrometer achieves a stated accuracy of 0.004 mm with an analogue reading of 0.005 mm, designed for consistent bench and in‑process inspection. Are the measuring faces wear resistant? Yes, the contact faces are made of carbide, providing enhanced wear resistance and long‑term dimensional stability for routine use. Is the gauge suitable for blind‑hole applications? The instrument is explicitly intended for blind‑hole measurement, featuring a self‑centring mechanism that ensures concentric contact within such bores. Does Metav IndustryLine provide technical support for integration into QA procedures? Metav IndustryLine and Metav Werkzeuge can supply further technical documentation and advice to assist with integration of the MS908.655 into quality control workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of self‑centring three‑point measurement and carbide measuring faces for consistent, reproducible results in blind‑hole bores; the interchangeable measuring inserts allow flexible adaptation across the nominal range. Order the instrument directly via Metav Werkzeuge or consult our specialists for application advice. Three‑point internal micrometer MS908.668 — self‑centring, carbide faces (Metav IndustryLine) The MS908.668 is a three‑point internal micrometer for accurate measurement of blind‑hole bores in workshop and inspection environments. Self‑centring three‑point measuring head Carbide measuring faces for wear resistance Interchangeable measuring inserts Delivered in protective case Faster, repeatable centring in blind‑hole measurement The self‑centring three‑point measuring head significantly reduces setup time when inspecting blind‑hole bores. By contacting the bore with three equidistant measuring points the instrument centres itself automatically, which improves repeatability compared with two‑point probes and speeds up routine checks. The analogue mechanism keeps the operation straightforward for technicians and maintenance staff who require reliable results without complex electronics. Metrology performance you can rely on Designed for industrial use, the instrument offers a stated accuracy 0.007 mm and a resolution 0.005 mm, values that make it well suited for quality control in machining and assembly. These specifications mean the device detects small deviations while providing a clear mechanical indication of the measurement. The combination of robust mechanical gearing and a clear, fine graduation supports precise readings under standard workshop conditions, helping to maintain product tolerances and reduce the risk of costly rework. Durable contact surfaces and flexible inserts The measuring faces are carbide tipped to resist wear during frequent use, preserving the nominal geometry and ensuring long‑term stability. Interchangeable measuring inserts permit adaptation across the stated measuring span so one instrument can cover a range of bore diameters without compromising accuracy. Supplied in a protective case, the tool is ready for transport to the machine or for storage in an inspection cabinet, keeping the measuring faces protected between uses. Trusted partner for precision tasks As part of the Metav IndustryLine range, this three‑point internal micrometer benefits from the supplier’s focus on accessibility and reliability. Metav’s approach to precision brings workshop‑grade metrology within reach, backed by a broad product portfolio and proven logistical support from Emmerich. The instrument suits metrology labs, maintenance teams and production lines that prioritise consistent centring, wear resistance and straightforward operation. For expert advice or to purchase the Metav IndustryLine three‑point internal micrometer MS908.668 with interchangeable inserts and carbide faces, please contact Metav Werkzeuge for tailored assistance and fast supply Technical data Article number: MS908.668 Brand: Metav IndustryLine Category: Messschrauben Numbers / Facts Measuring range: 225–240 mm Resolution (reading): 0.005 mm Accuracy: 0.007 mm Length: 145 mm Analogue instrument Special features / Versions Self‑centring three‑point measuring head Carbide measuring faces Interchangeable measuring inserts Suitable for blind‑hole bores Supplied in protective case FAQ What measuring range does the instrument cover? The MS908.668 three‑point internal micrometer covers a measuring span from 225 mm to 240 mm as delivered. Is this tool suitable for blind‑hole measurements? Yes; the three‑point, self‑centring design is specifically intended for reliable measurement of blind‑hole bores. Can the measuring inserts be replaced to adjust for different bore sizes? Interchangeable measuring inserts are provided, allowing the instrument to be adapted across its nominal measuring span. How precise are the readings from this analogue instrument? The instrument provides a resolution of 0.005 mm with a stated accuracy of 0.007 mm, suitable for workshop and production quality checks. Are the measuring faces durable under regular workshop use? The contact points are carbide tipped to increase wear resistance and maintain geometric integrity over extended use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise 0.004 mm accuracy, a self‑centring three‑point measuring head and carbide measuring faces for consistent blind‑hole measurement; order directly via Metav Werkzeuge or contact the consultancy team for tailored advice. MS908.656 Three‑Point Internal Micrometer — Self‑centring, 25–30 mm range (Metav IndustryLine) A three‑point internal micrometer designed for accurate measurement of blind holes and restricted bores in the 25–30 mm range, combining a compact form with stable contact geometry. Three‑point self‑centring measuring head Measuring range 25–30 mm Carbide measuring faces for wear resistance Analogue drive with 0.005 mm resolution Consistent results for blind‑hole inspection The instrument's self‑centring three‑point system guarantees repeatable contact with bore surfaces, reducing setup variance and rework in production inspection. The compact contact geometry suits restricted bores where standard callipers cannot reach, while the analogue drive and fine spindle allow controlled approach to the measuring surfaces. This configuration translates directly into fewer rejected parts and more reliable pass/fail decisions on the shop floor. Precision that meets workshop demands With a documented accuracy of 0.004 mm and a readable resolution of 0.005 mm, the device sits between general workshop tools and high‑precision instruments. The mechanical design and robust spindle ensure stable readings even in routine quality control. For applications that require exact internal diameters in small assemblies, this micrometer provides a balance of sensitivity and practical handling without invoking complex electronic systems. Durable contact surfaces for long service life The measuring faces are made from carbide, offering superior wear resistance under frequent use and abrasive conditions. That hard contact material preserves the reference geometry over many cycles and keeps measurement uncertainty low. An adjustment ring marked 25 assists with quick reference when setting or checking the nominal diameter, making repetitive tasks more efficient and less error‑prone. Compact format for fine mechanical work Classified in the micro range by its 25–30 mm span, the tool is ideal where small, precise components are involved. The short overall length supports handling in confined environments and maintains torsional stiffness for reliable contact pressure. As an analogue internal measuring instrument, it offers familiar operation for technicians while delivering the benefits of a three‑point system designed specifically for blind‑hole measurement. For precise and repeatable blind‑hole measurement, contact Metav Werkzeuge to request the Metav IndustryLine three‑point internal micrometer MS908.656 or to speak with a specialist at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: MS908.656 Name: Three‑point internal micrometer Manufacturer: Metav IndustryLine Facts Measuring range: 25–30 mm Resolution: 0.005 mm Accuracy: 0.004 mm Length: 90 mm Special features Self‑centring three‑point measuring head Carbide measuring faces Analogue micrometer design Adjustment ring marked 25 Suitable for blind‑hole measurement FAQ What measuring range does this instrument cover? The three‑point internal micrometer MS908.656 covers a measuring range of 25–30 mm, suited to small‑bore and blind‑hole applications. Is this micrometer suitable for blind‑hole measurement? Yes, the self‑centring three‑point system of the Metav IndustryLine three‑point internal micrometer is specifically designed to measure blind holes and restricted bores reliably. What accuracy and resolution can be expected? The instrument provides an accuracy of 0.004 mm with an analogue readable resolution of 0.005 mm, offering precise control for workshop inspections. Are the measuring faces durable for repeated use? The measuring faces are made of carbide, ensuring wear resistance and long‑term stability of the contact geometry under frequent measurement cycles. How is the instrument adjusted for repetitive tasks? An adjustment ring marked 25 is provided for quick reference and repeatable setting when working with the same nominal diameters. Is this a digital instrument? No, the MS908.656 is an analogue internal micrometer, combining mechanical reliability with a fine spindle for controlled readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of compact, workshop‑grade precision and robust design for repeatable blind‑hole measurement; the self‑centring three‑point contact and hardened measuring faces deliver reliable results across production and maintenance tasks. Order the instrument directly via Metav Werkzeuge or consult our advisors for application guidance. Three‑point internal micrometer MS908.657 (Metav IndustryLine) — Self‑centring, 30–40 mm The Three‑point internal micrometer MS908.657 is a mechanically driven measuring instrument intended for precise internal diameter checks, especially blind‑hole applications in fine mechanical and light industrial environments. Self‑centring three‑point contact system Measurement range 30–40 mm Hardened measuring faces for durability Precision designed for blind‑hole measurement The three‑point geometry provides self‑centring contact inside blind holes, ensuring that the contact points align automatically with the bore axis and thereby reduce eccentricity errors. With an accuracy of ±0.004 mm and a mechanical reading of 0.005 mm, this analogue measuring instrument translates fine thread motion into dependable metrology results without electronic dependence. The three‑point contact method also helps to average minor surface irregularities, which can reduce rework and speed up routine inspection tasks, making it suitable for both small series production and maintenance checks. Compact format for fine mechanical work Classified in the Mikro range (measurement span up to 100 mm), the instrument’s 30–40 mm span and overall length of 97 mm offer a favourable balance between reach and stiffness. This makes the device well suited to precision tasks where space is limited, such as watch and instrument repair, small housings and insert fittings. The hardened measuring faces increase wear resistance and preserve measurement consistency over long service intervals, so that calibration intervals remain predictable and downtime is minimised. Workshop‑ready robustness and simple handling The analogue design emphasises mechanical reliability: a clear adjustment ring (setting ring 40) allows quick pre‑setting and repeatable contact positioning, while the compact construction withstands everyday workshop handling. Delivered in a protective case for transport, the micrometer is prepared for secure storage and movement between benches or sites. The instrument’s straightforward operation and sturdy build lower the barrier to consistent metrology in production, inspection and maintenance workflows while keeping measurement practice transparent and traceable. Contact Metav Werkzeuge today for tailored application advice on the Metav IndustryLine Three‑point internal micrometer MS908.657 and ensure the right fit for blind‑hole inspection in your workshop Technical data Article number: MS908.657 Manufacturer: Metav IndustryLine Product type: Three‑point internal micrometer Suitable for: Blind‑hole measurement Core data Measurement range: 30–40 mm Length: 97 mm Accuracy: ±0.004 mm Reading (resolution): 0.005 mm Adjustment ring: 40 Mechanical type: Analogue Special features Self‑centring three‑point contact Hardened measuring faces Delivered in protective case for transport Suited to fine mechanical and light industrial use FAQ What makes the three‑point contact better for blind holes? The three‑point geometry centres itself in the bore and averages contact positions; the MS908.657 uses this principle to reduce eccentricity and provide stable internal diameter readings for blind‑hole applications. What accuracy and resolution can be expected from this instrument? The instrument offers an accuracy of ±0.004 mm with a mechanical reading of 0.005 mm, giving precise analogue measurement suitable for production checks and workshop inspection. Is the device suitable for watchmaking and small parts? Yes. With its compact dimensions and classification in the Mikro range, the micrometer is well adapted to fine mechanical work, small housings and components where a short, stiff measuring span is required. Are the measuring faces wear‑resistant? The micrometer is supplied with hardened measuring faces, which increases durability and helps maintain measurement consistency over extended use. Does the delivery include a protective case? The instrument is supplied in a protective case for transport and secure storage, making it straightforward to move between benches or sites. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the self-centring design, carbide measuring faces and ±0.005 mm accuracy to secure reproducible internal measurements in compact assemblies; order the three-point internal micrometer directly via Metav Werkzeuge or consult our specialists for technical guidance. Three-point internal micrometer MS908.660 — self-centring, 62–75 mm range A compact, analogue three-point internal micrometer designed for precise internal diameter checks in confined bores and fine-mechanical work. Self-centring three-point mechanism Measuring range 62–75 mm High accuracy ±0.005 mm Carbide measuring faces, analogue Precision where access is restricted The three-point internal micrometer is engineered for accurate measurements in confined spaces. Its self-centring mechanism ensures the measuring anvils align centrally within a bore, reducing operator-induced eccentricity and improving repeatability. With a readout resolution of 0.005 mm and a verified accuracy of ±0.005 mm, the instrument provides a reliable basis for quality control tasks where small deviations matter. The compact profile and 114 mm body length make this instrument particularly suitable for short, deep bores and components that cannot be accessed with larger gauges, offering precision without the need for complex fixturing. Durable construction for consistent results Built with carbide measuring faces, the instrument resists wear and maintains a stable contact geometry over extended use, which preserves measurement integrity in production environments. The analogue mechanism is robust and free of electronics, making it uncomplicated to operate in workshop conditions where durability is paramount. The combination of hardened contact surfaces and mechanical simplicity translates into low maintenance and consistent performance during repetitive checking routines, supporting efficient inspection workflows on the shop floor. Practical handling and typical applications Designed for ease of use in inspection and assembly, the instrument delivers fast, reliable readings for internal diameters between 62 and 75 mm. Its three-point contact is particularly effective for detecting form deviations and average bore sizes without additional adapters. Typical applications include component verification in machining, maintenance checks on housings and bearings, and quality assurance in small-batch production. The analogue format permits immediate interpretation of results, while the instrument’s geometry supports measurements that would be difficult with external gauges or callipers. Contact Metav Werkzeuge today for tailored advice and to arrange supply of the Metav IndustryLine three-point internal micrometer MS908.660 via Metav Werkzeuge GmbH; technical consultants are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: MS908.660 Brand: Metav IndustryLine Type: Analogue three-point internal micrometer Measuring range: 62–75 mm Readout: 0.005 mm Accuracy: ±0.005 mm Body length: 114 mm Self-centring mechanism Carbide measuring faces Suitable for blind-hole measurement Analogue (mechanical) operation FAQ How accurate is the three-point internal micrometer for routine inspection? The MS908.660 delivers an accuracy of ±0.005 mm, making it suitable for routine precision checks and quality control where sub-hundredth-millimetre repeatability is required. Can the instrument be used in blind or recess bores? Yes, the design is intended for confined and blind-hole measurements; the three-point contact provides reliable central alignment inside such bores. What maintenance is required to preserve measurement accuracy? Regular cleaning of contact surfaces and occasional verification on a calibrated reference ring are recommended to maintain the micrometer’s performance; the carbide measuring faces reduce wear and extend intervals between checks. Is the readout mechanical or electronic? This is an analogue instrument with a mechanical readout at 0.005 mm resolution, favouring robustness in workshop settings without relying on electronics. Which environments and applications suit this instrument best? The three-point internal micrometer is ideal for machine shops, maintenance workshops and inspection benches where compact, repeatable internal measurements are needed across small to medium-sized components. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com