Heavy-duty workshop verniers for large components
Our heavy-duty workshop verniers provide precise external and internal measurement of massive workpieces such as large shafts, flanges and housings, delivering stability and repeatable results even across spans up to 10,000 mm. Designed for the demands of heavy industry, shipbuilding and rail vehicle manufacture, they combine a distortion‑resistant construction in hardened or weight‑optimised special steel with ergonomic features like force‑limited measuring systems and fine adjustment for exact slide movement. Available in analogue versions with fine vernier scales or digital variants with data outputs for quality assurance integration, these calipers ensure reliable dimensional control in XXL machining.
10 mm Bore Centre Measuring Insert 60° Length 70 mm, For Caliper Adapter - Metav IndustryLine
Take advantage of the reliable combination of precise 10 mm bore spacing, 60° indexing and a compact 70 mm length for repeatable jigging and inspection tasks; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. Bore‑centre distance measuring insert 10 mm — measuring adapter insert for calipers, 60°, 70 mm (Metav IndustryLine) The Bore‑centre distance measuring insert 10 mm is an accessory for caliper measuring adapters, engineered to deliver a fixed 10 mm spacing at a 60° orientation for workshop and inspection applications. Precisely set 10 mm bore spacing 60° indexing for repeatable alignment 70 mm hardened length for stability Ø5 shank for standard caliper adapters Repeatable positioning for high‑throughput inspection The measuring insert provides a mechanically fixed reference for bore‑centre checks, eliminating time spent re‑setting fixtures. With a defined 10 mm centre distance and 60° indexing, the component converts a hand caliper into a quick verification tool that supports consistent results across repeated measurements. The compact 70 mm body reduces lever effects, enhancing contact stability and contributing directly to faster process throughput and fewer measuring errors. Easy integration with existing caliper adapters Designed for straightforward mounting, the insert uses a Ø5 shank to mate with standard caliper adapters and mounting plates. Compatibility with analogue calipers and adapter systems allows the accessory to be introduced without additional fixtures or calibration changes, preserving workshop workflows. The low mass (approximately 0.05 kg) minimises added inertia on the measuring instrument, keeping handling comfortable during repetitive tasks. Practical benefits for everyday metrology tasks By providing a fixed template for small bore patterns, the insert simplifies verification of jigs, small assemblies and production parts where a 10 mm spacing is required. The robust 70 mm length and precise indexing reduce setup variance, so quality checks become faster and more reliable. Use cases include first‑article inspection, in‑process sampling and quick assembly validation where speed and repeatability are paramount. The accessory complements standard caliper toolsets and supports traceable workflows when used alongside Metav’s calibration services. For targeted bore‑centre checks with Metav IndustryLine quality, request the measuring insert from Metav Werkzeuge or speak to our advisors at info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M240.323 GTIN: 4054469159553 Label: Bore‑centre measuring insert 10 mm, 60°, length 70 mm Eclass: 21170324 TARIC / HS code: 90178090 Brand: Metav IndustryLine Numbers / Core technical data Length: 70 mm Bore‑centre spacing: 10 mm Indexing angle: 60° Mounting shank diameter: Ø5 mm Weight: 0.05 kg Special features / Design Compatible with caliper adapters for 10 mm fittings Suitable for analogue calipers and adapter systems Compact, low‑mass design for handheld use Intended for bore‑centre verification and fixture checks FAQ What does the insert measure and how is it used? The measuring insert establishes a fixed 10 mm bore‑centre distance at 60° and is fitted into a compatible caliper adapter to provide rapid verification of small hole patterns. Which calipers are compatible with this adapter insert? Compatibility is with caliper systems that accept a Ø5 accessory shank; the design is optimised for standard analogue caliper adapters used in workshop metrology. Is the insert suitable for repetitive production checks? Yes, the fixed geometry and compact 70 mm length ensure repeatable positioning, making the insert appropriate for repetitive inspection and in‑process sampling. Does the product include traceable identification like GTIN or article number? The insert is supplied with GTIN 4054469159553 and article number M240.323 for inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100 mm Outer Groove Measuring Attachment For Digital Uni Carbon Fibre Caliper - Metav IndustryLine
Take advantage of the carbon‑fibre construction, 100 mm reach and compatibility with calipers that have a jaw thickness of 8 mm for consistent external groove measurements; order this insert directly via Metav Werkzeuge or consult our specialists for application advice. Insert for External Groove Measurement, 100 mm — carbon‑fibre accessory for digital universal calipers (Metav IndustryLine) The Insert for External Groove Measurement, 100 mm is a purpose‑built attachment for carbon‑fibre digital universal calipers that extends measurement capability to external grooves with consistent handling and fit. Carbon‑fibre construction for stable readings 100 mm reach for extended groove access Fits calipers with 8 mm jaw thickness Lightweight 0.2 kg for easy handling Reliable groove measurement with extended reach Designed for precise work on external grooves, the 100 mm insert provides an extended reach that simplifies measurement of grooves and recesses that standard jaws struggle to access. The accessory is intended for use in workshop and production environments where repeatable external groove measurement is required. Compatibility with digital universal calipers ensures the adapter can be integrated into established measuring workflows without altering the instrument’s basic operation. Stable performance thanks to carbon‑fibre design Made from carbon‑fibre, the insert combines low mass with structural stiffness, supporting steady contact during measurement and minimising thermal influence on short inspection runs. The lightweight nature (0.2 kg) reduces additional inertia on the caliper, helping operators maintain consistent handling over multiple measurements. These material benefits translate into practical advantages at the bench: easier manoeuvring into grooves and reduced risk of deflection compared with heavier attachments. Quick integration with digital universal calipers The insert is engineered to fit jaws with a thickness of 8 mm, delivering a secure seating and reliable transfer of the measuring surfaces to the caliper’s slide. Installation is straightforward and restores the caliper’s functionality for external groove checks without the need for special fixtures. As an accessory for digital universal calipers, it preserves the instrument’s measurement workflow while extending its application range. Practical accessory for everyday workshop use As a workshop accessory from Metav IndustryLine, the insert supports routine inspection and maintenance tasks where grooves must be checked quickly and reliably. Its design focuses on practicality: accessible reach, low weight and direct compatibility with common caliper jaws. For purchasing and logistics, Metav Werkzeuge supplies this accessory alongside a broad range of measuring tools, providing a single‑source option for workshops aiming to keep operations efficient and supplies standardised. For specification advice or to request the Metav IndustryLine 100 mm insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific calipers and applications Technical data Article number: M217.366 GTIN: 4054469183268 Manufacturer: Metav IndustryLine Facts Overall length: 100 mm Width: 16 mm Weight: 0.2 kg Compatible jaw thickness: 8 mm Special features Material: carbon‑fibre Application: external groove measurement Compatible with digital universal calipers Category: workshop calipers accessory eClass: 21170344 FAQ What is this insert used for? The insert is intended for external groove measurement; the Metav IndustryLine insert M217.366 extends the reach of digital universal calipers for groove and recess inspection. Will this accessory fit my caliper? It fits calipers with a jaw thickness of 8 mm; compatibility with a specific digital universal caliper is confirmed when the jaw thickness and mounting geometry match the M217.366 design. What material is the insert made from? The insert is manufactured from carbon‑fibre, chosen for its low mass and structural stiffness to support stable measurements. How long is the insert and how heavy is it? The insert measures 100 mm in overall length and has a mass of 0.2 kg, providing extended reach without significant additional weight. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper 150mm Jaw Depth Probe Stainless Hardened With Fine Adjustment, Factory Standard 0.10 mm - Metav IndustryLine
Take advantage of a large-format measuring range combined with a robust, fully hardened stainless steel construction and precise fine-adjustment control for consistent, repeatable measurements in production environments. Order the Digital Caliper directly via Metav Werkzeuge or consult our technical team if further specification is required. Digital Caliper M217.035 — 0–1000 mm, fine adjustment, stainless steel The Digital Caliper M217.035 is a large-format, industrial digital caliper designed for heavy-duty workshop measurement of large components, offering fine-adjustment and cross-point jaws for controlled contact and repeatable results. Large 0–1000 mm measuring range Fully hardened stainless steel frame Fine-adjustment with cross-point jaws Digital display with mm/inch and preset Reliable measurement across long components for production use The long measuring span of 0–1000 mm places this instrument in the large-format class suitable for heavy machining, fixtures and large housings, where reach and stability matter. With a resolution of 0.01 mm (and 0.0005 inch), the instrument provides the granularity expected for industrial quality control while the fully hardened stainless steel beam resists wear and keeps the scale straight over repeated use. The result is repeatable measurements across the entire length without frequent readjustment, supporting consistent process control and fewer production interruptions. Faster inspection through intuitive digital functions Equipped with a clear digital display and dedicated buttons for ON/OFF, mm/inch switching, zero/ABS, hold, tolerance and preset, the caliper streamlines routine checks and tolerance verification. The integrated RB 5 data output enables straightforward data capture for traceable records or connection to inspection stations, reducing manual transcription and accelerating inspection throughput. These capabilities translate into measurable time savings at the control stage and improved documentation for quality audits. Robust handling and controlled contact for accurate readings The combination of fine adjustment and cross-point jaws allows slow, precise approach and secure seating on irregular or angular surfaces, preventing overtravel and operator-induced variation. Constructed from fully hardened stainless steel, the instrument resists corrosion and mechanical wear in workshop environments, lowering the need for frequent replacement. Designed for practical workshop workflows, the caliper balances reach, stiffness and operator ergonomics so tasks on large components remain efficient and dependable. For reliable large-format measurement choose the Metav IndustryLine Digital Caliper M217.035 and contact Metav Werkzeuge in Emmerich for tailored advice and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M217.035 GTIN: 4054469110790 Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 0–1000 mm Resolution: 0.01 mm Resolution (inch): 0.0005 inch Jaw length: 150 mm Factory standard: Werksnorm 0.10 mm Data output: RB 5 Special features / Versions Material: stainless steel, fully hardened Fine-adjustment mechanism Cross-point jaws (precision contact) Digital display with ON/OFF, mm/inch, 0/ABS, HOLD, TOL, PRESET FAQ What measuring range and resolution does this caliper offer? The Digital Caliper M217.035 provides a 0–1000 mm measuring range with a display resolution of 0.01 mm (0.0005 inch), suitable for large-component inspection in workshops and production. Is the caliper suitable for rough workshop conditions? Yes. The Metav IndustryLine caliper combines fully hardened stainless steel construction with corrosion resistance and wear protection, making it robust for industrial workshop use. Which display and output functions are included? The instrument features a digital display with ON/OFF, mm/inch switching, zero/ABS, hold, tolerance and preset functions, plus an RB 5 data output for electronic data capture. How does the fine-adjustment benefit measurement results? The fine-adjustment mechanism and cross-point jaws enable controlled contact and slow approach to the measured surface, reducing operator-induced error and improving repeatability on large or uneven parts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper 150mm Jaw Length Fine Adjustment, Stainless Hardened, RB 5 Data Output, Factory Standard 0.07 mm - Metav IndustryLine
Take advantage of a large 1,000 mm measuring range and hardened stainless steel construction combined with a precise fine‑adjustment thumb wheel for reproducible measurements of large components; request advice from Metav Werkzeuge for application-specific details or ordering support. Digital caliper M217.055 by Metav IndustryLine — 1,000 mm range, fine adjustment The Digital caliper M217.055 is a heavy‑duty 1,000 mm digital caliper designed for workshop and production use, offering a hardened stainless‑steel body, an ergonomic fine‑adjustment wheel and a data output interface for process integration. 1,000 mm measuring range Hardened stainless‑steel construction Fine‑adjustment thumb wheel RB5 data output for measured value transfer High throughput measurement for large parts This measuring instrument delivers a pragmatic balance between range and repeatability: the 1,000 mm span covers large fixtures, housings and shafts while the hardened frame ensures profile stiffness across the entire length. The radiused jaws and extended jaw length of 150 mm allow safe contact on deeper or recessed features, reducing measurement retries and saving operator time. The robust digital readout, with a standard resolution of 0.01 mm, provides clear numeric feedback so decisions can be made immediately on the shop floor or fed into quality records via the RB5 data interface. Precise handling and ergonomic control Operational consistency is supported by the integrated fine‑adjustment wheel, which permits micro‑positioning without over‑driving the jaws — a decisive advantage when aligning large components where coarse movement would cause rework. The hardened stainless steel construction resists wear and keeps reference surfaces stable over long periods, so calibration intervals are extended and measurement uncertainty is reduced. The combination of mechanical control and a stable frame translates into faster set‑ups and fewer scrapped parts in continuous production. Simple digital workflow and traceability The display offers an array of function keys (on/off, mm/inch, zero/ABS, hold, tolerance and preset) that streamline everyday tasks and avoid manual transcription errors. When documentation or SPC logging is required, the RB5 data output enables direct transfer of measured values into data collection systems, supporting traceable quality assurance and faster reporting. The instrument runs from a 3 V supply and supports inch readings at 0.0005 in resolution, making it versatile for mixed‑unit processes and international production standards. Built for the workshop — protection and transport Delivery includes a protective case suitable for workshop transport, ensuring the caliper arrives in ready‑to‑use condition and is protected during relocation between workstations. The product meets the supplier’s stated factory tolerance (Werksnorm 0.07 mm), providing a clear baseline for incoming inspections and process control. For applications that require integration into an existing metrology setup, the presence of a data output and a hardened measuring frame simplifies retrofit and maintenance planning, reducing downtime and ensuring consistent measurement practice. Contact Metav Werkzeuge to discuss how the M217.055 can be integrated into existing inspection routines or to request a technical data sheet; local stock and specialist advice are available from Metav Werkzeuge in Emmerich. Technical data Article number: M217.055 GTIN: 4054469110950 Category: Messschieber Brand: Metav IndustryLine Label: Digital caliper, 1000 x 150 mm, without point, factory tolerance 0.07 mm, stainless Facts Measuring range: 0–1,000 mm Resolution: 0.01 mm Inch resolution: 0.0005 in Jaw length: 150 mm Power: 3 V Special features Hardened stainless‑steel construction Fine‑adjustment thumb wheel Digital display with on/off, mm/inch, zero/ABS, hold, tolerance, preset Data output: RB5 Delivered in protective case Factory tolerance: Werksnorm 0.07 mm FAQ Is the caliper suitable for large machine components? Yes. The M217.055 is a 1,000 mm digital caliper from Metav IndustryLine designed for measurement tasks on large housings, shafts and fixtures where extended reach and stiffness are required. What level of resolution and readability does the instrument provide? The instrument offers a digital reading resolution of 0.01 mm (0.0005 in) and supports immediate display functions such as tolerance and preset for production control. Can measurement data be transferred directly to a computer or SPC system? Yes. The caliper is equipped with an RB5 data output that allows measured values from the M217.055 to be exported for traceability and automated logging. How does the fine‑adjustment help in practice? The fine‑adjustment wheel enables controlled micro‑movement of the jaws for precise contact on delicate or deep features, improving repeatability and reducing the risk of over‑closing. Is the caliper delivered ready for use and protected for transport? The instrument is supplied in a protective case for secure transport and safe storage on site; the package supports routine workshop handling. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper 200mm Jaw Length Fine Adjustment, Stainless Steel, Factory Standard 0.07mm, ISO-Calibrated in Case - Metav IndustryLine
Benefit from the combination of a 1,000 mm measuring range, hardened stainless-steel construction and a fine-adjustment thumb roller that improves positional control; these attributes deliver repeatable, large-format measurements with practical handling for workshop use. Order the instrument directly via Metav Werkzeuge or consult the specialists for application-specific advice. Digital caliper M217.055.1 — Large-range digital caliper with fine-adjustment The Digital caliper M217.055.1 is a robust, 1,000 mm-range measuring instrument designed for heavy workshop and fixture work, offering precise positioning and a transport-ready case for safe handling during site measurement 1,000 mm measuring range Fine-adjustment thumb roller Hardened stainless-steel construction Reliable long-range measurement for heavy components Large-format measurements require both reach and stability; the 1,000 mm range of this caliper provides access to sizeable components while the fully hardened stainless-steel profile maintains profile stiffness to reduce deflection across the jaw span. The factory Werksnorm 0.07 mm indicates the instrument's benchmark performance under production check procedures, so inspectors and fitters gain a predictable error band for process documentation. The absence of a dedicated probe tip simplifies jaw geometry for common external and step measurements. Digital functions that speed up inspection and data capture The instrument combines a mechanical sliding system with a digital readout offering 0.01 mm resolution and inch resolution of 0.0005 in, enabling clear, comparable results across metric and imperial workflows. The display includes ON/OFF, mm/inch, zero/ABS, HOLD, TOL and PRESET modes to support pass/fail checks and preset references during repetitive tasks. A 3 V supply powers the electronics, and the integrated fine-adjustment control helps to position the jaws precisely without overshoot, reducing cycle time in batch inspections. Built for workshop resilience and easy transport Constructed from hardened, corrosion-resistant steel, the caliper tolerates frequent handling typical in production environments while the fine-adjustment roller protects delicate parts during contact setting. Delivery includes a transport case to safeguard the instrument during storage and transit, and the caliper is supplied without an additional tip to keep the jaws suitable for general-purpose external, internal and step measurements. Metav IndustryLine quality control at Emmerich ensures consistent lot handling, making this tool a durable choice for fixture and mould measurement tasks. For robust long-format measuring tasks, contact Metav Werkzeuge to discuss the Digital caliper M217.055.1 and arrange a technical consultation or datasheet delivery by phone or e‑mail Technical data Article number: M217.055.1 GTIN: 4054469110967 Eclass: 21170344 Tariff number: 90173000 Brand: Metav IndustryLine Facts Measuring range: 0–1000 mm Resolution: 0.01 mm Resolution (inch): 0.0005 in Factory accuracy (Werksnorm): 0.07 mm Jaw length: 200 mm Power supply: 3 V Data output: RB 5 Special features Material: hardened stainless steel Fine-adjustment thumb roller Digital display with ON/OFF, mm/inch, 0/ABS, HOLD, TOL, PRESET Supplied in transport case Supplied without measuring tip FAQ Is this caliper suitable for measuring large components such as housings or sleeves? The caliper’s 0–1000 mm measuring range and hardened construction make it suitable for larger housings and sleeves where a long, stiff jaw is required. What resolution and display functions are available? The instrument offers a 0.01 mm display resolution (0.0005 in) and includes ON/OFF, mm/inch, zero/ABS, HOLD, TOL and PRESET functions for efficient inspection workflows. Does the product come with a calibration certificate? The tool is supplied to Werksnorm 0.07 mm; no ISO 17025 calibration certificate is indicated with this item. Is the caliper suitable for routine workshop use and transport between sites? Yes. The hardened stainless-steel construction and included transport case support frequent workshop use and secure transit to different job sites. What power source does the digital electronics use? The measuring system is powered by a 3 V supply for the digital readout and associated functions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper 300mm Jaw Length Fine Adjustment, Stainless Hardened, Works Tolerance 0.07mm - Metav IndustryLine
Take advantage of the combination of a 1,000 mm measuring range, fine-adjustment control and reliable digital readout for reproducible large‑part measurements; order the caliper directly via Metav Werkzeuge or consult our advisers for application guidance. Digital Caliper M217.055.2 — 1,000 mm large‑range caliper with fine adjustment (Metav IndustryLine) The Digital Caliper M217.055.2 is a large‑range precision instrument designed for measuring substantial components in machine shops and fixture manufacture. 1,000 mm measuring range for large components Hardened stainless steel construction Fine‑adjustment thumb wheel for precise positioning RB 5 data output with mm/inch display Reproducible large‑format measurement for workshop use This large‑range instrument is built for repeatable checks on sizeable workpieces. The 1,000 mm range and extended jaw geometry provide the reach required for fixtures, housings and large fittings while the fully hardened stainless steel body resists wear and maintains profile stiffness. The integrated fine adjustment mechanism enables controlled approach and exact closing, reducing measurement variability during one‑hand operation. Combined with the robust construction, this results in stable readings over time and fewer re‑measures in production. Digital precision and data transfer that speeds up QC The caliper features a digital display with standard functions including ON/OFF, mm/inch, zero/ABS, hold, tolerance and preset, offering clear readouts and straightforward mode control. Resolution on the main display is 0.01 mm, supporting routine quality checks with a readable step size that balances precision and practicability for workshop inspection. Measurement values can be exported via RB 5 data output, simplifying documentation and integration into existing data workflows and reducing manual transcription time. Factory standard and practical ergonomics for everyday use Delivered to a factory tolerance of 0.07 mm, the instrument is aimed at heavy‑duty shop applications where range and durability are pivotal. The 300 mm jaw length supports deeper reach into assemblies while the hardened construction minimises wear at contact faces. The ergonomic slider and clear markings support efficient handling during repetitive tasks, making the tool well suited to production, maintenance and toolroom environments where both reach and operational ease are required. For tailored advice on using the Metav IndustryLine large‑range digital caliper and to arrange supply from Metav Werkzeuge in Emmerich, contact our team for competent product guidance and order placement. Technical data Article number: M217.055.2 GTIN: 4054469110974 eClass: 21170344 Tariff number: 90173000 Label: Digital‑Messschieber, 1000 x 300 mm, without tip, factory tolerance 0.07 mm, stainless, fine adjustment Facts Measuring range: 0–1,000 mm Jaw length: 300 mm Resolution (display): 0.01 mm Display inch resolution: 0.0005 in Power/mess system: 3 V Digital: yes Special features Material: stainless steel, fully hardened Fine adjustment: yes Display functions: ON/OFF, mm/inch, zero/ABS, HOLD, TOL, PRESET Data output: RB 5 Norm: factory standard (Werksnorm) 0.07 mm FAQ What is the measuring range of this caliper? The M217.055.2 covers a measuring range of 0–1,000 mm, suited to large components and fixtures. How fine is the display resolution and what accuracy is provided? The main display resolution is 0.01 mm and the instrument is delivered to a factory tolerance of 0.07 mm. Does the caliper support data transfer to a PC or data logger? Yes, the caliper includes an RB 5 data output for direct data capture and process documentation. What construction and features ensure long service life? A fully hardened stainless steel body and hardened contact faces minimise wear; the fine‑adjust mechanism improves handling during repetitive measurements. Is the caliper ready for shop use upon delivery? The M217.055.2 is supplied with factory standard accuracy and the full digital functions active for immediate integration into workshop quality routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper Carbon Fibre Inductive System Replaceable Jaw, IP65 - Metav IndustryLine
Take advantage of the combination of long-range measurement, robust carbon‑fibre construction and reliable digital output for reproducible workshop control of large components. Order the caliper directly via Metav Werkzeuge or ask the consultants for application advice. M217.361 Digital universal caliper — 1000 mm carbon fibre, IP65 (Metav IndustryLine) The M217.361 Digital universal caliper is a long‑range, inductive digital caliper intended for workshop measurement of large components and assemblies, offering a balance of reach and handling for fixture, housing and heavy‑duty machining tasks. 1000 mm carbon fibre beam IP65 protection for dusty and wet environments Inductive measuring system for stable readings Replaceable jaw and spring-mounted thumb roller Large‑range measurement with manageable handling The long‑beam design provides a measuring range of 0–1000 mm, which places this instrument among large‑range workshop calipers suited to components such as housings, large fixtures and medium‑sized shafts. The choice of carbon fibre for the main beam reduces thermal distortion compared with plain steels while keeping the device relatively easy to manoeuvre for single‑operator measurement tasks. With a jaw length of 100 mm and an inductive slide mechanism, the instrument combines reach with the stiffness required to preserve measurement repeatability across the full stroke. Consistent digital output and practical operation An inductive measuring system and a digital display with mm/inch, Hold, Set, On/Off, 0/Inch and Data keys deliver fast, unambiguous readouts and allow integration into data workflows via the RB 6 data output. The display resolution is 0.01 mm, enabling routine workshop tolerancing and fast checks; the specified accuracy of ±0.07 mm gives an objective basis for process control decisions when assessing larger parts where absolute micrometre precision is not required but reproducibility is crucial. Power is supplied by a 3 V CR 2032 cell, ensuring stable operation for extended inspection sessions. Practical features for everyday workshop use Durability and serviceability are emphasised by the replaceable measuring jaw and a spring‑mounted thumb roller, which simplify maintenance and prolong service life in busy environments. The IP65 rating protects the measuring electronics against dust ingress and water jets, reducing downtime and cleaning interventions in harsher production areas. Together these characteristics support efficient inspection routines and lower the total cost of ownership by limiting service interruptions and simplifying component replacement. Clear advantages for production and quality tasks As a long‑range digital caliper with a carbon‑fibre beam and inductive sensing, the instrument is particularly suited to applications where a wide measuring span and reliable digital output matter more than sub‑micrometre resolution. Typical use cases include bench and fixture inspection, outer and inner diameter checks on larger parts, and stage‑level verification during assembly. The combination of repeatable digital readings and rugged protection helps to streamline quality documentation and traceability within standard workshop processes. For tailored advice on integrating the M217.361 into production or inspection setups, contact Metav Werkzeuge for expert support and prompt dispatch from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: M217.361 GTIN: 4054469183213 Brand: Metav IndustryLine Core technical data Measuring range: 0–1000 mm Resolution: 0.01 mm Accuracy: ±0.07 mm IP protection: IP65 Jaw length: 100 mm Battery: 3 V CR 2032 Special features Material: Carbon fibre Measuring system: inductive Display functions: mm/inch, Hold, Set, On/Off, 0/Inch, Data Replaceable jaw and spring-mounted thumb roller Data output: RB 6 Digital caliper FAQ What measuring range does the caliper cover? The measuring range is 0–1000 mm, making the instrument suitable for larger workshop components and assemblies. How accurate are the readings from this caliper? The caliper provides readings with an accuracy of ±0.07 mm and a resolution of 0.01 mm, appropriate for large‑format workshop inspection where reproducibility is essential. Which data interface is available for digital collection? Data is provided via an RB 6 output, allowing the caliper to feed measurement values into compatible data capture systems. Is the instrument protected against workshop conditions? Yes — the instrument carries an IP65 rating for resistance to dust and water jets, and its carbon‑fibre beam reduces thermal effects compared with conventional steel beams. Are any user‑replaceable parts included for maintenance? The design includes a replaceable measuring jaw and a spring‑mounted thumb roller to simplify routine maintenance and extend service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper Fine Adjustment Stainless Steel With 500mm Jaws, Factory Standard RB 5 - Metav IndustryLine
Take advantage of the combination of a 1000 mm measuring range, fully hardened stainless steel construction and precise fine adjustment for reproducible long‑range measurements; order the digital caliper directly via Metav Werkzeuge or ask our consultants if needed Digital caliper M217.055.3 — 1000 mm range, fine adjustment (Metav IndustryLine) A Digital caliper M217.055.3 engineered for long‑range workshop measurement and quality control, combining a 1,000 mm span with robust, hardened construction and a multifunction digital readout 1000 mm measuring range Fully hardened stainless steel Precise fine‑adjustment mechanism Digital display with mm/inch and HOLD Long‑range measurement made dependable A measuring span of 1000 mm places this instrument in the workshop class for large components where stiffness and reach matter. Classified in the large‑range category for calipers, the instrument offers a long jaw of 500 mm that supports stable contact over extended distances. The construction in fully hardened stainless steel reduces wear and keeps the profile straight under frequent use, which translates into fewer rejections and lower rework rates in production runs. The long‑range design bridges the gap between handheld convenience and the reach usually expected only from specialised fixtures. Clear digital readout and process connectivity The integrated digital display provides standard functions — on/off, mm/inch, zero/absolute, HOLD, TOL and PRESET — which speed up inline inspections and reduce manual entry errors. Resolution is 0.01 mm with the inch resolution at 0.0005 in, while a dedicated RB 5 data output enables automated logging into measurement systems or SPC stations. Powered from a 3 V supply, the readout supports repeatable transfer of measurement values and fits into modern quality workflows where traceable data and simple conversion between units are essential. Built for reproducible workshop performance The inclusion of a fine‑adjustment mechanism ensures controlled closing speed and repeatable contact force, improving measurement reproducibility on medium to large workpieces. The instrument is supplied to a factory standard of 0.10 mm, giving a clear baseline for acceptance in routine checks. Material selection and full hardening increase resistance to deformation, so calibration intervals are extended and service costs are reduced. For applications where repeatability across multiple operators is critical, the mechanical design reduces user‑induced variance. Practical use in production and inspection Designed for frequent handling in the machine shop or inspection bay, the caliper combines ergonomic handling with rugged engineering. The robust frame and guarded slide keep the scale protected during daily use, and the digital functions cut inspection time by avoiding manual conversions. Integration via RB 5 allows measured values to feed directly into quality documentation or inspection software, supporting traceability and batch reporting. Metav IndustryLine’s positioning emphasises consistent supply and industrial compatibility for medium and heavy‑duty measurement tasks. Contact Metav Werkzeuge for a specification consultation on the M217.055.3 long‑range digital caliper or to arrange supply and integration advice from the Emmerich team Technical Data Article number: M217.055.3 GTIN: 4054469110981 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Category: Precision caliper Facts Measuring range: 0–1000 mm Resolution: 0.01 mm Inch resolution: 0.0005 in Jaw length: 500 mm Power supply: 3 V Data output: RB 5 Factory standard: 0.10 mm Special features Fully hardened stainless steel construction Fine‑adjustment mechanism for reproducible contact Digital functions: on/off, mm/inch, 0/ABS, HOLD, TOL, PRESET Readout with preset and tolerance check Designed for workshop and inspection use FAQ What measuring range does this caliper cover and how is it classified? The M217.055.3 covers 0–1000 mm and is classified as a large‑range precision caliper suitable for sizeable components and workshop inspection tasks. Which digital functions are available on the display? The instrument provides on/off, mm/inch conversion, zero/absolute (0/ABS), HOLD, tolerance (TOL) checks and PRESET functionality for standardised measuring routines. How is measurement data transferred to a PC or SPC system? Data from the caliper can be output via the RB 5 interface, enabling direct logging into inspection software or data collectors for traceability and process control. What material and hardness features improve longevity? The frame is made from fully hardened stainless steel, which reduces profile wear and maintains straightness over repetitive use, extending service life and stabilising measurement results. Is the device suitable for routine workshop inspection? Yes; the combination of long reach, fine adjustment and digital readout makes it appropriate for frequent workshop and inspection bay use, especially where reproducible results and data capture are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper Movable 150mm Jaw Fine Adjustment Stainless Steel, Factory Calibration in Case - Metav IndustryLine
Take advantage of the combination of long-range reach, stainless hardened construction and precise digital readout for consistent measurements on large components; order the instrument directly via Metav Werkzeuge or consult the team for application advice. Digital Caliper 1000 mm M217.259 — long‑reach digital caliper with 150 mm movable jaw, stainless hardened A Digital Caliper 1000 mm M217.259 engineered for workshop and production measurement of large parts, combining extended reach with fine adjustment and a clear digital interface Measuring range 0–1000 mm 150 mm movable jaw for deep reach Stainless, fully hardened construction Digital display with mm/inch & preset Accurate long‑range measurement where it matters This long‑reach instrument delivers a measuring range of 0–1000 mm, placing it in the large‑format class suited to heavy‑duty components. The digital resolution 0.01 mm (and 0.0005 in) ensures repeatable readings over the full stroke, while the electronic functions reduce interpretation errors common to analogue tools. The combination of extended range and fine display supports efficient quality checks on housings, fixtures and large assemblies, helping to keep production throughput steady and scrap rates low. Robust construction that maintains stability on long spans Built from stainless steel, fully hardened, the caliper body resists wear and retains profile rigidity essential for reproducible measurements across long distances. The 150 mm movable jaw provides access into deep bores and under flanges without compromising stiffness, and the integrated fine adjustment makes micro‑positioning straightforward during inspection. These mechanical choices reduce the risk of deflection and ensure dimensional control when measuring sizable workpieces. Faster readings and seamless data handling for workshops The electronic interface offers practical functions for shopfloor integration: ON/OFF, mm/inch, ZERO, ABS and PRESET on the display make setup and measurement cycles quicker. A dedicated data output (RB 2) enables transfer of values to inspection systems or data loggers, supporting traceable production records and simplified SPC tasks. The device therefore not only measures but feeds quality workflows, saving operator time and improving process documentation. Practical for machine shops and fixture builders Classified for the large‑format range, this caliper is particularly useful in machine and metalworking environments where reach and stability are required alongside clear digital feedback. The robust finish and precision features suit tasks such as checking spindle housings, large brackets and composite fixtures. Metav IndustryLine’s emphasis on accessible precision means that this instrument integrates into everyday workshop routines while offering the capability expected in industrial settings. Contact Metav Werkzeuge for tailored advice on supply and application of the M217.259 long‑reach digital caliper from Metav IndustryLine and ensure reliable delivery from Emmerich. Technical Data SKU: M217.259 GTIN: 4054469111308 Brand: Metav IndustryLine Label: Digital caliper 1000 mm, movable 150 mm jaw Facts Measuring range: 0–1000 mm Resolution: 0.01 mm / 0.0005 in Jaw length: 150 mm eClass: 21170344 Tariff code: 90173000 Special features Material: stainless steel, fully hardened Fine adjustment Digital display with ON/OFF, mm/inch, ZERO, ABS, PRESET Data output: RB 2 Norm: Werksnorm FAQ Is this instrument suitable for measuring large components such as housings and fixtures? Yes. The Digital Caliper 1000 mm M217.259 from Metav IndustryLine has a 0–1000 mm range and a 150 mm movable jaw, making it suitable for large workpieces and deep features typical in machining and fixture construction. What resolution and display functions are provided? The instrument offers a display resolution of 0.01 mm (0.0005 in) and includes ON/OFF, mm/inch, ZERO, ABS and PRESET functions to speed measurement cycles and reduce reading errors on the M217.259 digital caliper. Can measurement data be exported for documentation or SPC? Yes. The caliper features a data output RB 2, enabling connection to compatible data collection systems for traceable measurement logging and simplified quality documentation. What material and durability can be expected for workshop use? Constructed from stainless steel, fully hardened, the caliper is designed for robust shopfloor use, resisting wear while maintaining stiffness and dimensional stability over long spans. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Caliper With 150mm Jaw Tips, Fine Adjustment, Stainless Steel, Factory Standard 0.07mm, Carry Case - Metav IndustryLine
Take advantage of a high‑capacity measuring solution that combines a 1,000 mm measuring range, hardened stainless steel construction and a precise digital display with fine adjustment for repeatable results in large‑component workflows—ideal where reach and stiffness matter. Order the Digital Caliper directly via Metav Werkzeuge or consult our specialists for detailed integration advice. Digital Caliper M217.045 — 1,000 mm range, hardened stainless steel (Metav IndustryLine) The Digital Caliper M217.045 is a heavy‑duty digital measuring instrument with fine adjustment and pointed tips, engineered for accurate length control and robust handling in production and workshop environments. 1,000 mm measuring range for large components Hardened stainless steel construction Digital display with mm/inch, HOLD and TOL Supplied in protective transport case Stable reach and repeatable large‑part measurement With a 1,000 mm measuring span this gauge sits in the Large (500–1,000 mm) category and is tailored to applications where reach and profile stiffness are decisive. The use of hardened stainless steel ensures dimensional stability and wear resistance across repeated cycles, while a substantial mass of 2.7 kg supports steady contact and helps to reduce vibration‑induced scatter. For production tasks that require measuring larger workpieces—jigs, housings and machined subassemblies—this configuration offers a favourable balance of reach and rigidity for consistent results. Precise digital handling and operator control Electronic measurement is delivered via a clear digital display with a standard 0.01 mm resolution and an inch resolution of 0.0005. The instrument follows a Werksnorm 0.07 mm accuracy standard and includes fine adjustment to aid controlled closing of the jaws and reduce overshoot during positioning. The display provides quick toggles for mm/inch, HOLD, TOL and PRESET, enabling efficient tolerance checks and repeat measurements. Data output is available through RB 5, and the tool is powered by a 3 V system for reliable field operation. Robust design for workshop handling and transport Practical workshop use is supported by a 150 mm jaw length that balances access and stability, while the fully hardened stainless profile withstands routine knocks and cleaning. The gauge is supplied in a protective case for transport protection; this ensures secure delivery to the workshop bench or site. The overall build is aimed at frequent handling in industrial environments, reducing maintenance intervals and preserving measurement integrity over time. Integration and efficiency in quality workflows The instrument’s digital functions and fine adjustment reduce measuring time for repeated series and simplify inline tolerance assessment, supporting higher throughput in standard quality control loops. Its large measuring capacity complements smaller calipers in a metrology set‑up, providing a single‑tool solution for bigger components that would otherwise require multiple instruments. Metav’s focus on accessible precision means this caliper is positioned as a cost‑effective member of a complete workshop measurement offering. Contact Metav Werkzeuge for a technical consultation and to arrange procurement of the Metav IndustryLine Digital Caliper M217.045 for integration into production or inspection workflows Technical data Article number: M217.045 GTIN: 4054469110837 Category: Calipers / Measuring gauges Measuring range: 0–1,000 mm Resolution (display): 0.01 mm / 0.0005 in Accuracy (norm): Werksnorm 0.07 mm Weight: 2.7 kg Jaw length: 150 mm Power: 3 V Material: hardened stainless steel Digital functions: mm/inch, 0/ABS, HOLD, TOL, PRESET Fine adjustment: yes Data output: RB 5 Protective case: supplied Pointed tips: included FAQ What measurement range does this caliper cover and for what is it suitable? The Digital Caliper M217.045 covers 0–1,000 mm and is suitable for large‑component measurement in machine shops and production where extended reach and rigidity are required. What resolution and accuracy can be expected from this instrument? This Metav IndustryLine digital gauge offers a 0.01 mm display resolution (0.0005 in) with a Werksnorm 0.07 mm accuracy rating for workshop use. Is a case included for transport? Yes, the caliper is supplied in a protective case intended for secure transport to the workshop or jobsite. Which digital features and outputs are available? The tool provides mm/inch switching, HOLD, TOL and PRESET functions and offers RB 5 data output; it is powered by a 3 V supply. Is the caliper robust enough for regular production use? The M217.045 combines a hardened stainless‑steel profile with a substantial mass and fine adjustment, making it well suited for frequent handling and routine inspection tasks in production environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Carbon Workshop Caliper 130mm Jaws, IP65, Bluetooth Data - Filetta
Take advantage of a carbon-fibre beam with steel measuring faces, a full 0–1000 mm measuring range and reliable Digimatic/Bluetooth data transfer for uninterrupted workshop throughput; order directly via Metav Werkzeuge or consult our specialists for application advice. Digital workshop caliper M910.345 — carbon-fibre beam, Bluetooth & Digimatic The Digital workshop caliper M910.345 is a long-range measuring instrument designed for workshop and production use, combining a lightweight carbon-fibre beam with robust steel measuring faces for repeatable measurements on large components. Carbon-fibre beam with steel measuring faces 0–1000 mm measurement range with 130 mm jaws Digimatic and Bluetooth data output, IP65 protected Extended reach for large components and fixtures A measuring span of 0–1000 mm positions this instrument in the large-range class (500–1,000 mm), making it suitable for sizeable parts such as fixtures, housings and large workpieces. The extended reach reduces the need for multiple measuring tools and speeds up set-up and inspection cycles, delivering a clear efficiency gain on the shop floor. The long-beam design keeps rigidity where it matters so that repeatability is maintained across the whole measuring length. Precise digital readings and seamless data handling Equipped with a digital system that resolves to 0.01 mm, the caliper provides straightforward numeric read‑outs and selectable units for millimetres or inches. Data output via Digimatic and Bluetooth enables direct capture into measurement software or production control systems, eliminating manual transcription and lowering error risk. Stated repeatability and measurement stability reflect an effective error behaviour of ±0.08 mm, while the controlled measuring force of 5–10 N helps to reduce operator-induced variation. Workshop-proof construction with low weight The combination of a carbon-fibre beam with steel measuring faces achieves a beneficial balance between lightweight handling and wear-resistant contact surfaces. An IP65 rating protects the electronics and slide from dust and coolant exposure, enhancing uptime in demanding environments. With a jaw length of 130 mm the instrument reaches into recesses and across features while the total weight of about 1.5 kg keeps single-person handling practical for routine inspection tasks. Workflow-friendly features for industrial use Fine adjustment and a secure locking screw simplify clamping and incremental positioning during layout and inspection work. The instrument runs on a CR2032 battery and is delivered in a protective case for safe transport and storage between jobs. Designed for integration with standard data acquisition chains, the caliper supports faster documentation and traceability, helping production teams to maintain throughput without compromising on measurement quality. Speak to Metav Werkzeuge for application guidance on the Filetta carbon-fibre digital workshop caliper M910.345 — contact info@metav-werkzeuge.com or call +49 2822 7131930 for specification matching and procurement support. Technical Data Article number: M910.345 Manufacturer: Filetta Material: Carbon fibre with steel measuring faces Range: 0–1000 mm Protection class: IP65 Facts Resolution: 0.01 mm Accuracy / repeatability: ±0.08 mm Jaw length: 130 mm Measuring force: 5–10 N Weight: 1.5 kg Overall length: 1226 mm Power supply: 1× CR2032 Special features Digimatic and Bluetooth data output Digital display with mm/inch, ABS/INC, Reset/Preset Fine adjustment and locking screw Delivered in protective case Classified for large-range (500–1,000 mm) long-beam applications FAQ Is this caliper suitable for measuring large workshop components? Yes. The Filetta digital workshop caliper M910.345 is designed for large-range measurements up to 0–1000 mm, making it well suited to fixtures, housings and other sizeable workshop components. How accurate are measurements taken with this instrument? The caliper provides a resolution of 0.01 mm and a stated measurement behaviour around ±0.08 mm, supported by a controlled measuring force to improve repeatability. Can measurement data be transferred directly to a computer or data logger? Yes. The instrument offers Digimatic and Bluetooth outputs for direct integration with data collection systems and inspection software. Is the caliper protected against coolant and dust in a machining environment? The caliper has an IP65 protection rating, which provides resistance to dust and low-pressure water jets typically encountered in workshop settings. Does the delivery include a case for transport and storage? A protective case is supplied with the instrument to simplify safe transport and on-site storage between measurement tasks. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
1000mm Digital Precision Caliper 300mm Jaw Length, Carbon Fibre With Steel Measuring Faces, IP65 - Filetta
Benefit from a combination of a carbon-fibre beam, 0–1000 mm measuring range and IP65 protection for dependable shop‑floor measurement of large components; order this caliper directly via Metav Werkzeuge or ask our specialists for further advice. Digital workshop caliper Carbon 0–1000 mm — Precision caliper with long jaws and data output (Filetta) Digital workshop caliper Carbon 0–1000 mm designed for robust measurement tasks where reach, repeatability and digital data transfer are essential Carbon-fibre beam with steel measuring faces 0–1000 mm measuring range IP65 dust and water protection Digimatic + Bluetooth data output Accurate long‑range measurement for the busy workshop The 0–1000 mm measuring range paired with a carbon‑fibre beam delivers a favourable ratio of reach to stiffness that reduces deflection during handling. With an indicated accuracy ±0.16 mm and resolution 0.01 mm, the instrument provides rapid, repeatable readings for routine control tasks and setup operations. The long 300 mm jaw length gives access to deeper features and larger assemblies without compromising the stability of the measuring faces. This combination supports efficient process checks and reduces rework by making critical dimensions easy to verify on the bench or in the jig area. Digital output and traceable data capture for production control Equipped with both Digimatic and Bluetooth data interfaces, the caliper enables fast transfer of measurements into inspection systems or SPC software, improving traceability and reducing transcription errors. The digital display includes mm/inch, ABS/INC, and reset/preset functions for straightforward switching between modes and quick zeroing at reference points. Integrating the instrument into a digital workflow shortens inspection cycles and supports documented quality procedures, delivering tangible time savings and clearer audit trails for production quality control. Designed for workshop durability and comfortable handling The combination of a lightweight carbon beam and steel measuring faces offers robust contact surfaces where wear matters while keeping overall instrument mass low. Rated IP65, the caliper tolerates dusty environments and occasional water exposure typical of workshop settings. A fine‑adjustment mechanism and locking screw facilitate controlled closing and stable readings on irregular parts; power is supplied by a single CR2032 battery for long service life and easy replacement. The instrument is delivered in a protective transport case to simplify handling and safe storage when moving between workstations. Practical classification and typical applications This caliper falls into the category for long‑span workshop calipers, suitable for heavy machining, fixtures, pipe and vessel components, and mold or die assemblies where measurements up to one metre are required. The measured 5–10 N measuring force balances reliable contact without excessive deformation on thin‑walled sections. In practice, the tool is a reliable choice for maintenance teams, toolrooms and production shops that demand robust long‑reach measurement with digital data capture and straightforward operation. Contact Metav Werkzeuge in Emmerich to discuss suitability for specific tasks or to arrange procurement and technical consultation: info@metav-werkzeuge.com · +49 2822 7131930 Technical data SKU: M910.347 Label: Digital-Werkstattmessschieber Carbon 0-1000mm und 300mm Schnabellänge Manufacturer: Filetta Material: Carbon-fibre beam with steel measuring faces Protection class: IP65 Power: 1x CR2032 Measuring range: 0–1000 mm Resolution: 0.01 mm Accuracy: ±0.16 mm Facts Total length: 1226 mm Weight: 1.7 kg Jaw length: 300 mm Measuring force: 5–10 N Digital display: mm/inch, ABS/INC, Reset/Preset Special features Digimatic and Bluetooth data output Fine adjustment mechanism Locking screw for repeatable readings Delivered in a transport case for safe handling Suitable for workshop and production environments FAQ What measuring range does the caliper cover? The caliper offers a measuring range of 0–1000 mm, making it suitable for larger components and assemblies. Which materials are used in the caliper construction? The instrument combines a carbon‑fibre beam with steel measuring faces to provide a lightweight yet durable measuring device. How are measurements transferred to a PC or data system? Measurements can be output via Digimatic interface or Bluetooth, enabling direct capture into inspection software or SPC systems. Is the caliper suitable for use in a dusty or wet workshop? Yes, the caliper is rated IP65, offering protection against dust ingress and low‑pressure water jets typical in workshop environments. What battery does the caliper use and how long does it last? The caliper is powered by a single CR2032 battery, which is commonly used and straightforward to replace. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
1000mm Digital Precision Caliper Carbon Body With 200mm Jaw, IP65 - Filetta
Take advantage of the combination of lightweight construction, robust measuring faces and integrated data output for dependable workshop measurement. The carbon‑fibre beam and steel measuring surfaces provide a favourable stiffness‑to‑weight ratio, while digimatic and Bluetooth outputs support modern production workflows. Order the Filetta digital workshop caliper directly via Metav Werkzeuge or ask Metav’s consultants if additional specifications are required. Digital workshop caliper M910.346 — carbon‑fibre beam, 0–1000 mm, Bluetooth (Filetta) The Digital workshop caliper M910.346 is a rugged 0–1000 mm workshop instrument designed for industrial measurement tasks, combining a lightweight carbon‑fibre beam with steel measuring faces and dual data outputs for process integration. Carbon fibre beam with steel measuring faces Measurement range 0–1000 mm Digimatic and Bluetooth data output IP65 protection for harsh environments Large‑range capability without heavy handling The caliper is classified for the 500–1,000 mm range, making it suitable for large‑format workshop tasks where reach and repeatability matter. The carbon‑fibre beam reduces overall mass to 1.6 kg, improving handling during longer measurements, while the steel measuring faces preserve wear resistance where contact is concentrated. This combination gives a practical compromise between stiffness and ease of use, so measurements across assemblies and fixtures remain reproducible without unnecessary operator fatigue. Reliable digital capture for production processes Equipped with digimatic and Bluetooth outputs, the instrument supports direct data transfer into SPC systems and measurement logs. The display resolution is 0.01 mm, enabling fine reading for quality control, and the caliper features a fine‑adjustment thumbwheel and a locking screw for secure setting. The specified measuring force of 5–10 N contributes to repeatability by standardising contact pressure during checks. These attributes make the device a practical choice where traceable, machine‑readable readings speed up inspection routines and reduce transcription errors. Built to endure in workshop environments An IP65 rating shields the electronics against dust and jets of water, while the supplied protective case simplifies transport and on‑site storage. The instrument’s overall length of 1,226 mm and 200 mm jaw length provide the extra reach needed for larger components without compromising robustness. Power is supplied by a single CR2032 battery, keeping maintenance straightforward; the caliper’s compact electronics and sealed design reduce downtime and extend service intervals. Practical integration and everyday benefits Functionality focuses on workshop efficiency: the lightweight construction shortens handling time, digital outputs remove manual logging, and the locking screw plus fine adjustment allow precise setting for repetitive operations. As a workshop instrument, it is appropriate for heavy‑duty measurement tasks and suits environments where a balance of reach, durability and digital connectivity is required. Compatibility with common digimatic interfaces ensures simple integration with existing measurement stations. For a practical, connected measuring solution, contact Metav Werkzeuge to discuss the Filetta digital workshop caliper M910.346 and arrange delivery or integration details via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: M910.346 Manufacturer: Filetta Product: Digital workshop caliper Carbon 0–1000 mm Weight: 1.6 kg Overall length: 1,226 mm Jaw length: 200 mm Battery: 1x CR2032 Facts Resolution: 0.01 mm Specified accuracy: 0.12 mm Measuring force: 5–10 N Protection class: IP65 Special features Carbon fibre beam with steel measuring faces Digimatic and Bluetooth data output Fine adjustment wheel Locking screw Supplied in protective case FAQ What measurement range does the caliper cover? The Filetta digital workshop caliper M910.346 covers a measuring range of 0–1000 mm and is intended for large‑range workshop measurement tasks. Which outputs are available for data capture? This caliper provides both digimatic and Bluetooth outputs for direct transfer of readings into data collection systems and digital inspection workflows. How precise is the instrument and what is the display resolution? The instrument has a display resolution of 0.01 mm and a specified accuracy of 0.12 mm, with a measuring force of 5–10 N to aid repeatability. Is the caliper suitable for harsh workshop conditions? Yes. The caliper is rated IP65, protecting it against dust ingress and water jets, and it is supplied in a protective case for transport and storage. What materials form the measuring surfaces and beam? The beam is made from carbon fibre to reduce weight, while the measuring faces are steel for durability and wear resistance. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
1000mm Digital Precision Caliper Color 2.4" Touchscreen Wireless USB ISO 17025 Calibrated Tablet Mount - Microtech Metrology
Combine the 1,000 mm measuring range, professional aluminium construction and ISO 17025 calibration for repeatable large‑component inspection; benefit from wireless and USB data transfer for streamlined documentation. Order the Precision Caliper directly via Metav Werkzeuge or ask our consultants if needed. Precision Caliper 0–1000 mm – Extra‑long digital caliper with 2.4" colour touchscreen (Microtech Metrology) The Precision Caliper 0–1000 mm is an extra‑long digital caliper designed for large‑format measurements in production and workshop environments, combining a wide measuring range with calibrated traceability and modern data transfer options. 1,000 mm measuring range for large components Delivered with ISO 17025 calibration certificate Wireless + USB data transfer for digital workflows 2.4" colour touchscreen for clear, fast readout Built for large‑component inspection This caliper sits in the large‑format class (500–1,000 mm) and is engineered to measure sizeable parts such as housings, fixtures and heavy components with a 1,000 mm span. The aluminium construction keeps the instrument lighter than steel equivalents while preserving sufficient rigidity for workshop use, so measurement reach is increased without excessive operator fatigue. The device offers a resolution of 0.01 mm and an accuracy of ±0.04 mm, values that match typical industrial quality‑control needs and support reliable pass/fail decisions on larger workpieces. Traceable accuracy for quality assurance Delivered fully calibrated to ISO 17025, the tool arrives with a formal calibration certificate that documents traceability and measurement uncertainty. This traceable calibration simplifies internal audits and supplier quality checks, giving procurement and QA teams documented confidence in measurement results. The included certificate is beneficial for regulated production environments where documented proof of calibration status is required for incoming inspection or final acceptance. Seamless data capture and workflow integration Equipped with Wireless and USB outputs and a 2.4" colour touchscreen, the caliper is prepared for digital measurement chains. Readings can be exported to inspection software or logged via USB for statistical process control, reducing manual transcription errors and saving time at the workstation. The touchscreen presents clear numeric values and simple controls for switching units or zeroing, supporting efficient process documentation and faster cycle times. Ergonomics and handling optimised for the shop floor Practical details such as the aluminium body and a substantial jaw length of 400 mm provide a good balance between reach and usability. The specified measuring force range (1–20 N) gives an operational guideline so operators can apply consistent contact pressure, improving repeatability across users. The digital readout and modern data outputs make the instrument suited to routine workshop measurement tasks while remaining robust enough for regular industrial use. For large‑format measuring tasks where traceability and digital data capture matter, choose the Microtech Metrology Precision Caliper with ISO 17025 certification — contact Metav Werkzeuge for ordering or technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 142411442 GTIN: 4061905037696 Manufacturer: Microtech Metrology Digital display: Colour 2.4" touchscreen Data output: Wireless + USB Material: Aluminium Delivered calibrated: ISO 17025 certificate included Facts Measuring range: 0–1,000 mm Resolution: 0.01 mm Accuracy: ±0.04 mm Measuring force: 1–20 N Jaw length: 400 mm Special features Extra‑long caliper for large components (500–1,000 mm class) Wireless connectivity for digital workflows USB connection for direct data export Supplied with ISO 17025 calibration certificate Compact 2.4" colour touchscreen for clear readout FAQ Is the caliper supplied with a calibration certificate? Yes. The Precision Caliper from Microtech Metrology is supplied fully calibrated to ISO 17025 and includes the corresponding calibration certificate. What measurement accuracy can be expected for large parts? The instrument provides a resolution of 0.01 mm and an accuracy of ±0.04 mm, suitable for standard industrial inspection of large components using the 0–1,000 mm range. How are measurements transferred to inspection software? Measurements can be exported via Wireless or USB from the caliper to a PC or data logger, enabling integration with SPC and documentation systems. Is the caliper suitable for everyday workshop use? Yes. With an aluminium body for reduced weight, a 400 mm jaw length and digital readout, the caliper is built for frequent shop‑floor use while remaining portable and practical. What does the specified measuring force range mean in practice? The listed 1–20 N range indicates the practical contact pressure window; maintaining consistent contact force supports repeatable results across different operators and measuring scenarios. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Digital Precision Caliper Colour 2.4" Touchscreen Wireless USB ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of long‑range measuring capacity, robust Aluminium construction and integrated data transfer for streamlined inspection workflows; order the calibrated device directly via Metav Werkzeuge or request guidance from our consultants. Digital Caliper — Microtech Metrology long‑beam caliper with 2.4″ colour touchscreen A digital caliper optimised for large‑format component measurement, offering Wireless and USB data output and ISO 17025 calibration for traceable results 2.4″ colour touchscreen display Wireless and USB data transfer Calibrated to ISO 17025 with certificate Consistent precision for large components The long‑beam measuring instrument delivers repeatable results across an extended range thanks to its measuring range 0–1000 mm and industrial‑grade construction. With a resolution of 0.01 mm and an indicated accuracy of 0.06 mm, the device is designed to reduce rework and speed up quality checks on sizable assemblies. The included ISO 17025 calibration certificate documents traceability and supports quality systems, making this caliper suitable for incoming inspection and process control. Faster data flow and fewer transcription errors Integrated Wireless and USB outputs combined with the 2.4″ colour touchscreen simplify measurement capture and handover to inspection software. Touchscreen menus accelerate routine tasks, while direct digital transfer eliminates manual logging, improving throughput in busy metrology benches. The combination of live display and reliable interfaces supports systematic data collection, enabling efficient reporting and faster decision‑making on the shop floor. Built for handling long measurements with confidence Constructed from Aluminium and featuring a jaw length of 600 mm, the instrument belongs to the large (500–1,000 mm) long‑beam category that balances reach with profile stiffness. That design reduces deflection during extended measurements and keeps uncertainty stable along the measuring span. Robust components and clear, colour feedback on the display make the caliper convenient to use in workshop environments while preserving laboratory‑grade traceability for critical parts. Contact Metav Werkzeuge to discuss the ISO 17025‑calibrated Microtech Metrology long‑beam digital caliper (SKU 142411462) and arrange delivery from Emmerich Technical data Article number: 142411462 GTIN: 4061905455513 Manufacturer: Microtech Metrology Material: Aluminium Display: Colour 2.4" touchscreen Data output: Wireless + USB Measuring range: 0–1000 mm Accuracy: 0.06 mm Digital: Yes ISO 17025 calibration: Certificate included Facts Reading resolution: 0.01 mm Measuring range: 0–1000 mm Jaw length: 600 mm Accuracy: 0.06 mm Special features Colour 2.4" touchscreen display Wireless and USB data transfer Aluminium construction for reduced weight and rigidity ISO 17025 calibration with certificate Long‑beam design for large‑format components FAQ What measuring range does this instrument cover? The instrument covers a measuring range of 0–1000 mm, making it suitable for large‑format components and assemblies. Is the caliper delivered calibrated and traceable? Yes. The caliper is delivered calibrated to ISO 17025 and includes a calibration certificate for traceability with the Microtech Metrology long‑beam caliper (SKU 142411462). Which data outputs are available for integration? Measurement data can be exported via Wireless connection or USB, enabling direct transfer to inspection software or data loggers. What resolution and accuracy can be expected? The device provides a resolution of 0.01 mm and an indicated accuracy of 0.06 mm, suitable for workshop quality control of large parts. What material is the frame and how does that affect handling? The frame is made from Aluminium, which offers a good balance of stiffness and manageable weight for long‑span measurements. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Digital Precision Caliper With 150mm Sliding Jaw, mm/inch Display, Factory Calibration Werksnorm - Metav IndustryLine
Combining a 1,000 mm measuring range with a lightweight aluminium profile and a clear digital readout, this workshop caliper supports accurate measurement of large components while remaining easy to handle. Secure the instrument through Metav Werkzeuge for dependable supply and expert advice on integration into existing measuring processes. M217.215 Workshop caliper — digital, 1,000 mm, Metav IndustryLine The M217.215 workshop caliper is a large‑range, workshop-grade measuring instrument designed for use on assemblies, fixtures and components up to 1,000 mm, offering a robust aluminium frame and extended jaw length for deeper access. Digital display with mm/inch and zero 1,000 mm measuring range for large parts Aluminium profile for reduced weight and rigidity Measure large components with precision and control With a maximum range of 1,000 mm, this caliper is classified for large workshop measurements where reach and repeatability matter. The aluminium profile keeps overall weight down while preserving section stiffness, which helps to reduce bending and repeatability errors over long spans. A 150 mm jaw length increases access into recesses and deep features, so routine checks on housings, large shafts or fixture plates become more practical without sacrificing handling. Fast readout and straightforward data transfer for traceable workflows The instrument features a digital display with ON/OFF, mm/inch selection and a zero function for rapid set‑up and unit changes, cutting measurement time and interpretation errors. The specified RB 1 data output provides a standardised connection point for external recording devices or data loggers, supporting digital quality‑control workflows and simple logging of measurement results. These capabilities deliver measurable efficiency gains in workshop inspection routines and small‑series production. Workshop durability and conformity to factory standards Built to meet the declared Werksnorm (factory standard), the caliper is intended for everyday workshop usage rather than laboratory environments, balancing robustness with usability. The construction and features reflect Metav IndustryLine’s focus on practical precision: stable jaw geometry for consistent contact, readable digits for quick decisions and a design that tolerates the demands of a busy shop floor. Together, these elements support predictable results during process checks and incoming inspection tasks. For specification guidance or to arrange supply of the Metav IndustryLine M217.215 workshop caliper with RB 1 output, please contact Metav Werkzeuge in Emmerich for tailored advice by e‑mail or phone. Technical data SKU: M217.215 Brand: Metav IndustryLine Material: aluminium profile Measuring range: 0–1000 mm Facts Measuring range max: 1000 mm Jaw length: 150 mm Tariff number: 90173000 EClass: 21170344 Special features Digital display with ON/OFF, mm/inch and zero button Data output: RB 1 Factory standard (Werksnorm) Designed for workshop measurements FAQ What measuring range is covered by this caliper? The M217.215 workshop caliper covers a measuring range from 0 to 1,000 mm, making it suitable for larger components and fixtures. Can the display switch between metric and imperial units? Yes, the instrument’s digital display supports switching between mm and inch via the mm/inch button for flexible use across different documentation standards. What kind of data output is provided for documentation? The caliper is equipped with an RB 1 data output intended for external recording and integration into data‑logging workflows. Is the caliper intended for workshop conditions or laboratory use? This instrument is designed to meet factory standard (Werksnorm) requirements and is optimised for routine workshop measurement tasks where robustness and usability are priorities. What construction benefits support stable measurements over long ranges? A rigid aluminium profile and extended jaw geometry help to limit deflection during handling, preserving repeatability when measuring longer parts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Werkstattmessschieber, 0,01mm, IP 65 - Metav IndustryLine
Das 1989 gegründete Vertriebsunternehmen von Messwerkzeugen steht mit seiner Eigenmarke Metav IndustryLine für Premium-Messwerkzeuge zu einem kleinem Preis. Das wichtigste auf einen Blick Messbereich: bis 1000mm Ablesung: 0,01mm Material: Kohlenstoff-Faser Ausführung: digital Datenausgang: Bluetooth Daumenstück gefedert Reichweite, die passt 0–1000mm schafft Spielraum für Projekte mit Länge. Du erreichst auch entfernte Punkte gut. Weniger Unterbrechung, mehr Klarheit. Perfekt für Werkbank, Lager und Baustelle. Wir haben uns Gedanken gemacht, wie wir die einzelnen Messbereiche der Messschieber Klassifizieren können. Klassifizierung Messbereiche beim Messschieber. Expertentip: Führe Messungen immer unter gleichen Bedingung aus. Im Idealfall im einem Messlabor, das 20° Celsius vorhält. Unsicher, ob das Werkzeug das Richtige ist? Oder fehlen technische Daten? Sprechen Sie uns einfach an! 📧 eMail: info@metav-werkzeuge.com ☎️ Telefon: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Technische Daten für den digitalen Werkstattmessschieber von Metav IndustryLine: Bestellnummer: M217.355.3 Messbereich: 0-1000mm Marke: Metav IndustryLine Bezeichnung: Werkstattmessschieber Daumenstück gefedert Ausführung: digital Gewicht: 12,7kg Material: Kohlenstoff-Faser Lieferung im Kasten Schnabellänge: 500mm Ablesung: 0,01mm Anzeige: mit mm/inch-, HOLD-, SET-, ON/OFF-, 0/INC- und DATA-Tasten Datenausgang: Bluetooth Ablesung in Inch/Zoll: 0,0005 Messsystem: induktiv IP-Schutz: IP 65 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com Wichtige Aspekte beim Erwerb eines Messschiebers: Neben der Präzision und dem Betriebsbereich sind erweiterte Eigenschaften wie die Funktionalität zum Datenoutput oder die Messkraftverwaltung von großer Signifikanz. Der Einsatz eines Messschiebers mit kontrollierter Messkraft ist besonders in der Qualitätssicherung und in Laborumgebungen vorteilhaft. Zusätzlich sollten man darauf Achten, ob man einen kalibrierten Messschieber braucht. Man kann die Kalibrierung bei Lieferung vornehmen und aus Gründen der Prozesskontinuität alle 12 Monate erneuern.
1000mm Digital Werkstattmessschieber, 0,01mm, IP 65 - Metav IndustryLine
Die außerordentlichen Bewertungen von Metav Werkzeuge stehen für mehr als 42.000 hochzufriedene Kunden. Mache Deine eigenen Erfahrungen und shoppe bei metav-shop.de.! HIGHLIGHTS Messbereich: bis 1000mm Ablesung: 0,01mm Material: Kohlenstoff-Faser Ausführung: digital Datenausgang: Bluetooth Daumenstück gefedert Alles im Blick – 0 bis 1000mm Der Bereich bis 1000mm bringt dir verlässliche Ergebnisse über die ganze Länge. Du bleibst sicher, auch bei großen Werkstücken. Das sorgt für saubere Arbeitsschritte. Gut in Produktion und Service. Schauen Sie hier, wie wir die Messbereiche klassifiziert haben. Klassifizierung Messbereiche beim Messschieber. Die Messwerkzeuge von Metav IndustryLine werden von unseren Profis für Messwerkzeuge empfohlen. Metav IndustryLine steht für Premium Messwerkzeuge zu einem vervorragenden Preis. Alle Messwerkzeuge werden nach der Produktion gestestet. Produktspezifikationen für digitalen Werkstattmessschieber von Metav IndustryLine: Marke: Metav IndustryLine Bezeichnung: Werkstattmessschieber Daumenstück gefedert Bestellnummer: M217.355.2 Fakten: Messbereich: 0 bis 1000mm Gewicht: 8,5kg Schnabellänge: 300mm Ablesung: 0,01mm Datenausgang: Bluetooth Ablesung in Inch/Zoll: 0,0005 IP-Schutz: IP 65 Ausführungen Ausführung: digital Material: Kohlenstoff-Faser Lieferung im Kasten Anzeige: mit mm/inch-, HOLD-, SET-, ON/OFF-, 0/INC- und DATA-Tasten Messsystem: induktiv Daumenstück gefedert Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com Worauf man achten sollte, wenn man einen Messschieber kaufen möchte: Neben den zentralen Faktoren Genauigkeit und Messbereich gewinnen auch komplette Funktionen wie der Datenausgang oder die Überwachung der Messkraft zunehmend an Bedeutung. Für die Qualitätssicherung sowie Laboreinsätze erweist sich der Messschieber mit geregelter Messkraft als besonders nutzbringend. Zusätzlich sollten man darauf Achten, ob man einen kalibrierten Messschieber braucht. Das Kalibrierungsverfahren kann sofort bei Lieferung initiiert werden und bedarf für die Gewährleistung der Prozessstabilität einer jährlichen Wiederholung.
1000mm Digital Werkstattmessschieber, 0,01mm, IP 65 - Metav IndustryLine
Die beeindruckenden Bewertungen von Metav Werkzeuge stehen für viele erfreute Kunden. Überzeuge Dich persönlich und kaufe auf metav-shop.de! Alles im Blick – bis 1000mm 0–1000mm gibt dir Luft für lange Bauteile. Du arbeitest gleichmäßig und ohne Stopp. Das hilft bei Montage, Wartung und Prüfung. So bleibt dein Ergebnis sauber. Unsere Definition der EInteilung der Messbereiche. Klassifizierung Messbereiche beim Messschieber. Profi-Tip: Welche Messkraft ist richtig? Nur mit Daumendruck schließen – übermäßiges Klemmen biegt die Schenkel zusammen und führt zu „negativen“ Messwerten. Spezifikationen: Marke: Metav IndustryLine Bezeichnung: Werkstattmessschieber Daumenstück gefedert Bestellnummer: M217.355.1 Zahlen und Fakten: Messbereich: 0-1000mm Gewicht: 6,4kg Schnabellänge: 200mm Ablesung: 0,01mm Datenausgang: Bluetooth Ablesung in Inch/Zoll: 0,0005 IP-Schutz: IP 65 Ausführungen Ausführung: digital Material: Kohlenstoff-Faser Lieferung im Kasten Anzeige: mit mm/inch-, HOLD-, SET-, ON/OFF-, 0/INC- und DATA-Tasten Messsystem: induktiv Daumenstück gefedert Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com Wichtige Aspekte beim Erwerb eines Messschiebers: Zugleich mit der Präzision und dem Messbereich sind die Berücksichtigung von Features wie Datenexport und Messkraftkontrolle unerlässlich. Der Einsatz eines Messschiebers mit kontrollierter Messkraft ist besonders in der Qualitätssicherung und in Laborumgebungen vorteilhaft. Daneben ist wichtig zu prüfen, ob ein kalibrierter Messschieber benötigt wird. Die Möglichkeit zur Kalibrierung besteht unmittelbar bei Entgegennahme; zur Sicherstellung der Prozessstabilität sollte regelmäßig jährlich neu kalibriert werden.
1000mm Digital Werkstattmessschieber, 0,01mm, IP 65 - Metav IndustryLine
Die außerordentlichen Bewertungen von Metav Werkzeuge stehen für mehr als 42.000 erfreute Kunden. Probiere es aus und shoppe auf metav-shop.de.! Das wichtigste auf einen Blick Messbereich: bis 1000mm Ablesung: 0,01mm Material: Kohlenstoff-Faser Ausführung: digital Datenausgang: Bluetooth Daumenstück gefedert Reichweite, die passtbis 1000mm Die Reichweite von bis 1000mm gibt dir Platz für lange Teile. Du kommst bequem von Anfang bis Ende. So bleiben Wege kurz und die Arbeit fließt. Ideal für Werkstatt, Bau und Schule. Wir haben uns Gedanken gemacht, wie wir die einzelnen Messbereiche der Messschieber Klassifizieren können. Klassifizierung Messbereiche beim Messschieber. Die Premium Messwerkzeuge von Metav IndustryLine werden von unseren Profis für Messwerkzeuge empfohlen. Metav IndustryLine steht für Premium Messwerkzeuge zu einem vervorragenden Preis. Alle Messwerkzeuge werden nach der Produktion gestestet. Technische Daten zumdigitalen Werkstattmessschieber von Metav IndustryLine: Marke: Metav IndustryLine Bezeichnung: Werkstattmessschieber Daumenstück gefedert Bestellnummer: M217.355 Zahlen: Messbereich: 0 bis 1000mm Gewicht: 5,3kg Schnabellänge: 15mm Ablesung: 0,01mm Datenausgang: Bluetooth Ablesung in Inch/Zoll: 0,0005 IP-Schutz: IP 65 Besonderheiten Ausführung: digital Material: Kohlenstoff-Faser Lieferung im Kasten Digitalanzeige: mit mm/inch-, HOLD-, SET-, ON/OFF-, 0/INC- und DATA-Tasten Messsystem: induktiv Daumenstück gefedert Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; www.metav-shop.de; info@metav-werkzeuge.com
1000mm Digital Workshop Caliper 150mm Jaws Fine Adjustment Inductive IP65 Data Buttons, Stainless Hardened - Metav IndustryLine
The combination of IP65 protection, an inductive digital measuring system and a 1,000 mm measuring range delivers robust, reproducible results for large workshop components; reliable hardness and fine adjustment maintain measurement stability over long spans. Order the caliper directly via Metav Werkzeuge or contact the consultants for assistance with integration and delivery. Digital workshop caliper M217.125 — Metav IndustryLine, 1,000 mm range, IP65 Digital workshop caliper M217.125 from Metav IndustryLine is a long‑range, inductive workshop caliper designed for heavy‑duty measuring tasks in the machine shop and toolroom 1,000 mm range for large components IP65 dust and splash protection Hardened stainless steel construction Fine‑adjustment thumbwheel for precise setting Durable precision for long measuring runs The long‑bar caliper (500–1,000 mm class) is engineered to combine reach and rigidity so that measurements remain reproducible across longer spans. The unit employs an inductive measuring system, which reduces wear compared with mechanical slides and preserves measurement consistency. With a resolution of 0.01 mm and a stated general tolerance of 0.07 mm, this instrument suits workshop quality control where robust repeatability and clear digital read‑out are required. The body is made from hardened stainless steel, offering corrosion resistance and the stiffness needed for a 1,000 mm instrument; the integrated fine‑adjustment thumbwheel permits controlled approach to the workpiece to avoid overshoot and contact shocks. Fast data handling and fewer transcription errors Data transfer and documentation are simplified by the built‑in RB 6 data output and the comprehensive display functions (mm/inch, HOLD, SET, ON/OFF, 0/INC, DATA). The digital interface reduces manual entry and speeds up inspection routines—an efficiency gain that translates into lower downstream rework and faster throughput. The caliper’s IP65 rating protects the electronics from coolant sprays and chips on the shop floor, increasing uptime and lowering maintenance intervals. These features make the device a pragmatic choice for integration into standard workshop workflows or basic digitised measurement stations. Practical ergonomics for everyday workshop use Weight and jaw geometry are balanced for two‑handed handling and controlled positioning: the instrument weighs 2.3 kg and has extended jaws with a 150 mm tip length to reach into deeper features. Classified as a long‑bar workshop caliper, it is suitable for measuring large clamps, housings and assemblies commonly encountered in heavy machining, fixture construction and pipework. The robust construction and protective rating provide a trustworthy measuring tool that is simple to use under routine workshop conditions and can withstand the physical demands of continuous shop‑floor operation. Discuss specification and delivery options with Metav Werkzeuge to fit the Metav IndustryLine M217.125 with IP65 protection and inductive measurement into existing inspection routines Technical Data Article number: M217.125 GTIN: 4054469146898 Manufacturer: Metav IndustryLine Material: stainless steel, fully hardened Protection: IP65 Numbers / Core technical data Measuring range: 0–1000 mm Resolution: 0.01 mm Resolution (inch): 0.0005 in Weight: 2.3 kg Jaw length: 150 mm General tolerance: 0.07 mm Special features Inductive measuring system Digital display with mm/inch, HOLD, SET, ON/OFF, 0/INC, DATA Fine‑adjustment thumbwheel Data output: RB 6 Hardened stainless‑steel construction Suitable for large‑format components (500–1,000 mm class) Protection against dust and water splashes (IP65) FAQ What is the measuring range of this caliper? The Metav IndustryLine M217.125 offers a measuring range of 0–1000 mm, making it suitable for large components and assemblies. What resolution and accuracy can be expected? The instrument provides a resolution of 0.01 mm (0.0005 in) with a general tolerance indicated as 0.07 mm for workshop use. Is the caliper protected against coolant and dust? Yes. The M217.125 is rated IP65, offering protection against dust ingress and low‑pressure water jets, which is beneficial for shop‑floor conditions. Which data interfaces and display functions are available? The caliper features an inductive measuring system, a digital display with mm/inch, HOLD, SET, ON/OFF, 0/INC and DATA buttons, and a RB 6 data output for reliable transfer to inspection or documentation systems. For which workshop tasks is this caliper intended? Designed as a long‑bar workshop caliper, the M217.125 is intended for measuring larger fixtures, housings, pipes and assemblies in machining, fixture construction and heavy‑duty workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Workshop Caliper 200mm Jaw, Fine Adjustment, Inductive Measurement, IP65, Stainless Hardened Steel, Data Output RB 6 - Metav IndustryLine
Take advantage of robust large-range measurement, IP65 protection and an inductive sensing system for reliable workshop results; order the caliper directly via Metav Werkzeuge or request advice from our consultants. Digital workshop caliper M217.125.1 — 1000 mm range, IP65, inductive The Digital workshop caliper M217.125.1 is a heavy-duty, inductive digital caliper designed for workshop and fixture applications that require a large-range measuring tool up to 1000 mm. Inductive measuring system for stable readings IP65 protection against dust and water ingress Fine-adjustment mechanism for precise positioning 1000 mm range with 200 mm long jaws Accurate large-range measurement for heavy components This caliper is engineered for measurements where reach and repeatability matter: classified in the large-range (500–1,000 mm) category, it combines a long measuring span with a rigid profile to keep deflection and measurement uncertainty low. The 1000 mm measuring range makes it suitable for medium to large workpieces, such as mounts, housings and larger fixtures commonly found in machine shops and toolrooms. Thanks to the robust construction and hardened slide, the tool maintains alignment across the span and delivers reproducible readings for production checks and set-up tasks. Reliable electronic sensing and protection for workshop environments Equipped with an inductive measuring system and a sealed housing, the instrument provides consistent readings under harsh conditions. The digital display offers 0.01 mm resolution and tactile keys for mm/inch, HOLD, SET, ON/OFF, 0/INC and DATA functions, enabling quick unit changes and temporary value retention. With an IP65 ingress rating, the electronics are protected from dust and low-pressure water jets, which reduces downtime and cleaning-related faults—an important advantage in coolant-prone and dusty production areas. The caliper also includes a DATA output via RB 6, facilitating data transfer to inspection systems or logging workflows. Fine positioning and durable measuring faces for precise handling A mechanical fine-adjustment feature ensures controlled approach to the measuring surfaces, preventing accidental overrun and allowing exact closing on small features. The long jaws—200 mm in length—reach into deeper bores or over larger steps while remaining stable. The body and jaws are made from stainless steel, fully hardened, offering wear resistance and dimensional stability over repeated cycles. These material choices extend service life and preserve calibration intervals, making the instrument a dependable workshop standard. Integration into the metrology workflow and productivity benefits Beyond single readings, the caliper supports structured quality checks: the combination of digital output and familiar display controls streamlines transfer of measured values into SPC or measurement logs, saving operator time and reducing transcription errors. The instrument’s balanced mass (approx. 2.3 kg) reflects its robust build and helps steady handling during longer measurements. In practice, the tool reduces rework and speeds up set-up times by delivering clear, repeatable data that integrates with existing workshop processes. Choose the Metav IndustryLine caliper for dependable large-range metrology and contact Metav Werkzeuge for tailored advice and delivery from Emmerich. Technical data Article number: M217.125.1 GTIN: 4054469164823 ECLASS: 21170344 Protection class: IP 65 Weight: 2.3 kg Core specifications Measuring range: 0–1000 mm Resolution: 0.01 mm Jaw length: 200 mm Measuring system: inductive Display: digital (mm/inch) Data output: RB 6 Features and materials Material: stainless steel, fully hardened Fine adjustment mechanism Digital keys: mm/inch, HOLD, SET, ON/OFF, 0/INC, DATA Robust workshop design for production use FAQ What accuracy and resolution can be expected with this caliper? The caliper provides a resolution of 0.01 mm and, with its inductive measuring system and hardened construction, achieves industrially relevant repeatability suitable for workshop inspection and set-up tasks. Is the caliper suitable for use in coolant or dusty environments? Yes. The IP65 rating means the caliper’s electronics are sealed against dust and low-pressure water jets, making the M217.125.1 appropriate for typical workshop conditions. How is measurement data transferred from the tool? The instrument includes a DATA output using the RB 6 interface, enabling transfer of values into data collection systems or inspection software for traceable documentation. Can the long jaws reach into deeper bores and steps reliably? The 200 mm jaw length and fine-adjustment control allow secure positioning in deeper features while maintaining contact stability for accurate readings on larger components. Which materials and build quality support long-term use of the caliper? Constructed from stainless steel, fully hardened, the caliper resists wear and preserves dimensional stability under frequent use, supporting long service life in professional environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Workshop Caliper With 150mm Pointed Jaws, Fine Adjustment, Inductive System, IP65, Supplied In Case - Metav IndustryLine
Reliable measurement across a full-metre span, combined with IP65 protection and a fine-adjustment control, supports consistent shop-floor results and reduced rework. Benefit from the robust inductive measuring system and stainless, fully hardened construction for long service life. Order the digital workshop caliper directly via Metav Werkzeuge or ask our consultants if needed. Digital workshop caliper M217.135 — 1,000 mm range, IP65, Metav IndustryLine The digital workshop caliper M217.135 is a heavy-duty measuring instrument for large components in fabrication and assembly, offering a 0–1,000 mm measuring range with a 150 mm pointed-jaw length for deep or awkward profiles. IP65 protection class for workshop use Inductive measuring system, stable readings Fine-adjustment thumb screw for repeatable contact Stainless hardened steel construction Built for reliable large-part measurement This instrument is a Large-range caliper designed specifically for measurements up to 1,000 mm, where profile stiffness and reproducibility matter. The frame and jaws are made from stainless hardened steel, which resists wear and maintains form under frequent use; this increases long-term precision and reduces maintenance needs. The extended jaw length (150 mm) permits access to recessed features and deep grooves without compromising rigidity, so measurements remain consistent across batches and setups. Precision and process reliability on the shop floor Measurement is handled by an inductive measuring system that delivers stable, interference-resistant readings and a standard resolution of 0.01 mm (with inch resolution shown on the display). The digital display includes mm/inch, HOLD, SET, ON/OFF, 0/INC and DATA functions for quick unit switching and data capture. The fine-adjustment mechanism gives controlled contact force for repeatable results, improving repeatability when comparing serial parts or recording quality-control data. These features translate into fewer rejects and smoother production flows. Robust protection and industrial readiness With an IP65 rating the instrument withstands dust and water jets typical of industrial workshops, making it suitable for machining centres and production benches. The fully sealed electronics and hardened measuring surfaces guard against coolant and chip ingress, so accuracy is preserved even in harsh environments. Supplied as part of the Metav IndustryLine, this caliper combines practical robustness with the commercial reliability of a European precision partner, supporting steady supply and straightforward integration into inspection routines. Request availability or technical advice for the Metav IndustryLine digital workshop caliper M217.135 from Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M217.135 GTIN: 4054469146928 ECLASS: 21170344 Category: Messschieber (calipers) SKU: M217.135 Facts Measuring range: 0–1000 mm Jaw length: 150 mm Resolution: 0.01 mm / 0.0005 in Protection class: IP65 Measuring system: inductive Materials & special features Material: stainless hardened steel Fine adjustment: yes Digital display: mm/inch, HOLD, SET, ON/OFF, 0/INC, DATA Data output: RB 6 Digital: yes FAQ What measuring range does this caliper cover? The digital workshop caliper M217.135 covers a measuring range from 0 to 1,000 mm, designed for large components and assemblies. Is the instrument suitable for use at the machine bench? Yes, the M217.135 features an IP65 protection rating and a hardened stainless-steel construction suited to machine‑shop conditions. Which display and data functions are available? The caliper provides an mm/inch display plus HOLD, SET, ON/OFF, 0/INC and DATA functions for straightforward unit switching and data capture with the M217.135. What measuring system ensures repeatable readings? An inductive measuring system is used in the M217.135 to give stable, interference-resistant readings and consistent repeatability. Can the caliper handle deep or recessed features? The 150 mm pointed jaw length on the M217.135 enables access to recessed areas and deep features while keeping measurement stiffness. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Workshop Caliper With 200mm Pointed Jaws, Fine Adjustment, IP65 - Metav IndustryLine
Take advantage of robust IP65 protection, hardened stainless steel construction and precise fine adjustment for reliable large‑range measurement — order the Digital workshop caliper with pointed jaws IP65, 1000 x 200mm directly via Metav Werkzeuge or ask our consultants if needed. Digital workshop caliper with pointed jaws IP65, 1000 x 200mm — Metav IndustryLine, inductive system, RB 6 data interface Digital workshop caliper with pointed jaws IP65, 1000 x 200mm is a heavy‑duty, inductive measuring instrument designed for precise dimensional control of large components in the workshop and production environment. Digital display with mm/inch and data output RB 6 IP65 protection for workshop environments Hardened stainless steel construction Fine-adjustment and 1000 mm measuring range Built to withstand the workshop while keeping measurements precise This instrument combines a sealed IP65 rating with a fully hardened stainless steel beam, delivering corrosion resistance and protection against dust and water jets for daily shop use. The robust construction stabilises the long beam over the full 1000 mm measuring range, so measurements remain reproducible even when handling larger workpieces. The integrated fine adjustment mechanism permits incremental, controlled approach of the jaws for repeatable contact and reduced operator error, which is particularly beneficial when measuring heavy or awkward components where small positional shifts would otherwise distort results. Clear digital readout and dependable data transfer for quality control The caliper employs an inductive measuring system and a digital readout with 0.01 mm resolution (0.0005 in), making it suitable for routine industrial metrology where a clear numerical display speeds inspection cycles. The display supports mm/inch conversion, HOLD, SET, ON/OFF, zero/inc functions and a DATA key for measurement capture. A dedicated RB 6 data output enables wired transfer of readings to SPC consoles or data loggers, simplifying documentation and integration into traceability workflows. These features reduce manual transcription errors, accelerate inspection steps and support a consistent production flow. Size‑appropriate design for large components and ergonomic handling With a jaw length of 200 mm and a total weight of 2.3 kg, the caliper is classified for the large‑format category where profile stiffness and handling matter; it is particularly suited to clamp, fixture and housing inspection in metalworking and heavy machining. The instrument’s geometry and hardened beam keep deflection low across long spans, so measurements of shafts, pipe fittings or mounting faces remain trustworthy. The combination of a practical jaw design and a fine‑adjustment wheel eases single‑operator use when precise placement is required, improving throughput without sacrificing accuracy. For reliable large‑range measurement with integrated data capture, contact Metav Werkzeuge to discuss suitability for specific components or to place an order for the Metav IndustryLine caliper with RB 6 interface. Technical Data Article number: M217.135.1 GTIN: 4054469164854 Manufacturer: Metav IndustryLine Facts Measuring range: 0–1000 mm Resolution: 0.01 mm / 0.0005 in Weight: 2.3 kg Jaw length: 200 mm Protection class: IP65 Special features Material: hardened stainless steel Measuring system: inductive Fine adjustment Digital display: mm/inch, HOLD, SET, ON/OFF, 0/INC, DATA Data output: RB 6 FAQ Is this caliper suitable for use at the machine or only as a workshop tool? The caliper’s IP65 rating and hardened stainless steel construction make it suitable for workshop and on‑machine inspection tasks where exposure to coolant spray or dust can occur. What level of resolution and display functions does the instrument offer? The digital readout provides 0.01 mm resolution (0.0005 in) and includes mm/inch conversion, HOLD, SET, zero/inc and DATA functions for measurement capture. Can measurements be exported directly to quality software? Yes, the integrated RB 6 data output supports wired transfer of readings to compatible data loggers or SPC systems, facilitating digital documentation. How does the fine‑adjustment aid measurement quality? The fine‑adjustment mechanism allows controlled jaw movement for delicate approach, reducing operator‑induced variation and improving repeatability on long spans. Is the caliper suitable for measurement of heavy or large fixtures? The design targets large‑format measurement tasks: the robust beam and extended jaw length are intended to keep deflection low across the 1000 mm range for reliable readings. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Precision measurement for heavy components with workshop calipers
Workshop calipers, also described as heavy-duty calipers or industrial vernier calipers, are engineered for exact external and internal measurement on large workpieces. Designed for shipbuilding, rail vehicle manufacture and heavy plant assembly, these calipers deliver stable, repeatable readings even across extreme spans up to 10,000 mm (10 metres).
How these calipers perform in industrial practice
Built with an extremely distortion-free frame of hardened or weight-optimised special steel, workshop calipers maintain alignment across long reaches and heavy contact forces. They measure shafts, flanges and housings by combining robust jaws with optional measuring-force-limiting systems, fine micrometric slider adjustment and rounded internal measuring faces to reduce damage and measurement error. Available in analogue form with a fine vernier scale or as a digital variant with data output for direct integration into quality assurance systems.
Practical advantages that improve production
- Proven metrological stability for large components thanks to distortion-free construction.
- Hands-on ergonomics through measuring-force-limiting and precision fine adjustment, reducing operator error.
- Flexible data handling with digital data output for seamless quality documentation.
- Materials and design that withstand heavy workshop environments: hardened special steel or weight-optimised alternatives.
- Measurement range scalability up to 10,000 mm (10 metres) for XXL applications.
Why Metav is the sensible partner for these tools
Metav stands for the democratisation of precision and acts as a quality filter for the European market from its base in Emmerich. With over 48,000 customers and a portfolio exceeding 250,000 products, Metav combines long-standing expertise with a comprehensive range that simplifies procurement for industry and trade. In the field of workshop calipers, Metav’s assortment is positioned as the optimal choice, offering both analogue vernier solutions and modern digital models suitable for integration into industrial measurement workflows.
Core takeaway
For reliable dimensional control of oversized components, workshop calipers deliver measurable gains in repeatability, ergonomics and process integration—making them indispensable in heavy industry.
FAQ
What measuring ranges are available for workshop calipers?
Workshop calipers are offered for extreme tasks, with models covering spans up to 10,000 mm (10 metres) to accommodate large shafts, flanges and housings.
Can these calipers connect to quality assurance systems?
Yes. Many industrial vernier calipers are available with digital data output, enabling direct transfer of measurement values into QA systems for traceable documentation.
Which design features reduce operator-induced error?
Features such as a measuring-force-limiting system, a precise fine-adjustment mechanism and rounded internal measuring faces reduce variability and the risk of damaging components during measurement.
What materials ensure long-term stability for large-scale measurement?
Metav’s workshop calipers use hardened special steel or weight-optimised variants to ensure minimal distortion and lasting dimensional stability even under heavy use.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com