Efficient shaft cutters and ball nose cutters for versatile milling
Shaft cutters and ball nose cutters serve as robust rotating tools for roughing, face milling, corner milling and slotting, offering economical replacement of indexable inserts rather than whole solid tools. Available in versions with internal coolant to feed lubricant directly to each cutting edge or without internal coolant relying on external nozzles, these cutters ensure effective chip evacuation and thermal control suited to standard materials or deep pocket and cavity work. By preventing chip re-cutting and protecting cutting edges, they deliver higher feed rates, improved surface finish and extended tool life in demanding metalworking applications.
25mm Shank End Mill for R390-11T3 Indexable Inserts, 90° Cutting Angle, 45mm Cutting Length - Teknik Makina
Benefit from the combination of robust compatibility with Sandvik R390-11T3 indexable inserts, a 25 mm shank diameter for improved rigidity, and a secure Torx fastening system for dependable toolholding; order the cutter directly via Metav Werkzeuge or consult our specialists for application guidance. Schaftfräser S592-1TM — Shank cutter for R390-11T3 indexable inserts (Teknik Makina) The Schaftfräser S592-1TM is a shank-mounted milling cutter engineered for use with R390-11T3 indexable inserts, optimised for shoulder milling and general face-milling applications in steel and similar materials. Compatible with Sandvik R390-11T3 inserts 25 mm shank diameter for high rigidity Three cutting edges for consistent removal 90° cutting angle for precise shoulder milling Streamlined tooling through proven insert compatibility The principal advantage of this shank-mounted cutter is its compatibility with R390-11T3 indexable inserts, which allows shops to standardise on a widely used insert family. Using established inserts reduces inventory complexity and enables straightforward regrinding or replacement when wear occurs. The combination of a purpose-built holder and proven cutting bodies supports predictable cycle times and contributes to lower overall tooling cost by simplifying reconditioning and stock control. Rigidity and stability for consistent machining results A 25 mm shank diameter provides notable stiffness at the tool interface, reducing deflection under load and improving dimensional control when machining shoulders or larger steps. The cutter’s 90° cutting angle is suitable for square shoulder operations, delivering clean vertical faces without secondary profiling. The tool’s balanced geometry and mass (approx. 0.446 kg) help maintain spindle behaviour and vibration resistance, supporting repeatable surface finish and tolerance adherence in serial production. Fast, secure insert clamping for reduced downtime Insert retention is achieved with a Torx system using an M2.5x7 screw and a T8 key, offering a positive, low-maintenance clamping method that minimises the risk of loosening in high-speed cycles. This fastening approach shortens changeover time compared with more complex clamping systems and enables safe, repeatable torque application during maintenance. The cutter’s three cutting edges are arranged to ensure uniform engagement, improving chip control and extending insert life under typical industrial cutting parameters. Suitable applications and productivity considerations Designed primarily as a shank-mounted cutter for indexable inserts, this tool is suitable for operations requiring robust shoulder cuts and face milling in workshop and light industrial settings. The configuration with three edges and a 120 mm overall length gives a balance between reach and stiffness; the 45 mm cutting length provides sufficient engagement for stepped machining. When paired with appropriate inserts and cutting data, the system enhances throughput and reduces the frequency of tool changeovers, making it a rational choice for demanding production routines. Contact Metav Werkzeuge for tailored application advice and precise tooling selection — reach our specialists at +49 2822 7131930 or info@metav-werkzeuge.com to discuss suitability for specific machining tasks Technical data Article number: S592-1TM Designation: Shank cutter for R390-11T3 indexable inserts Brand: Teknik Makina Compatible inserts: R390-11T3 Facts Shank diameter: 25 mm Cutting length (shank): 45 mm Overall length: 120 mm Diameter: 25 mm Number of cutting edges: 3 Weight: 0.446 kg Cutting angle: 90° Special features Torx screw: M2.5x7 Torx key size: T8 Suitable for Sandvik R390-11T3 inserts SKU: S592-1TM FAQ Which inserts fit this shank cutter? The cutter accepts R390-11T3 indexable inserts, making it compatible with that Sandvik insert family for shoulder and face milling. What is the shank diameter and why does it matter? The tool has a 25 mm shank diameter, which increases rigidity and reduces deflection for improved dimensional accuracy during machining. How many cutting edges does the cutter have? This shank-mounted cutter features three cutting edges, designed for consistent material removal and balanced cutting forces. What fastening hardware is used for insert clamping? Insert retention uses a Torx M2.5x7 screw operated with a T8 key, providing secure and repeatable clamping. Is this tool suitable for high-speed machining? The cutter is intended for industrial milling operations; compatibility with high-speed regimes depends on insert grade, workpiece material and cutting parameters chosen. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank End Mill for WNGX 0403 Indexable Inserts, 4 Cutting Edges - Teknik Makina
Benefit from a rigid 25 mm shank and compatibility with WNGX 0403 indexable inserts for reliable, repeatable milling. The 110 mm overall length provides reach while the four cutting edges ensure efficient chip evacuation and stable results. Order the tool directly via Metav Werkzeuge or consult the Metav team for application advice. Milling cutter S945TM – 25 mm shank, for WNGX 0403 indexable inserts (Teknik Makina) The Milling cutter S945TM is a shank-mounted milling tool engineered for indexable-insert machining with WNGX 0403 inserts, offering a balance of rigidity and accessibility for a wide range of workshop milling tasks. 25 mm shank diameter for stable clamping Compatible with WNGX 0403 indexable inserts Four cutting edges for efficient material removal Torx clamping screw M2.5x5.5, key T8 Greater process stability through a rigid shank and optimised geometry The combination of a 25 mm shank and a precisely balanced cutter body reduces vibration and run-out, which directly benefits surface finish and tool life. With four cutting edges, the design provides consistent material removal per revolution and smoother engagement in interrupted cuts. For jobs where cycle time and repeatability matter, this configuration helps to maintain machining tolerances and reduces the need for secondary finishing operations. The result is a measurable contribution to process efficiency and predictable production output. Fast insert changes and secure clamping for uninterrupted productivity Tooling compatibility with WNGX 0403 indexable inserts keeps consumable logistics simple and reduces machine downtime. The clamping system uses a M2.5x5.5 Torx screw operated with a T8 key, allowing quick, toolmaker-friendly insert replacement without complex adjustments. The Torx interface provides positive drive and reliable screw retention, lowering the risk of loosening under heavy cutting forces. Compatibility with common Korloy inserts further streamlines supply chains and makes the cutter straightforward to integrate into existing tooling inventories. Practical workshop fit and low-maintenance operation An 110 mm overall length gives the tool enough reach for many set-ups while retaining rigidity at the cutting zone. The shank-mounted format simplifies toolholding and reduces balancing requirements compared with longer multi-component holders. Routine maintenance is confined to insert replacement and periodic torque checks on the Torx screw, keeping service intervals short. For procurement and supply reliability, Metav Werkzeuge’s Emmerich operations act as a quality filter for the European market, supporting consistent deliveries and technical guidance for workshop integration. Contact Metav Werkzeuge in Emmerich for application-specific advice or to order the Teknik Makina S945TM — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S945TM Name: Milling cutter for WNGX 0403 indexable inserts Manufacturer: Teknik Makina Key dimensions Diameter: 25 mm Shank diameter: 25 mm Overall length: 110 mm Cutting edges: 4 Special features Compatible with WNGX 0403 indexable inserts Suitable for Korloy inserts Torx clamping screw M2.5x5.5, key T8 eClass 21180806, ETIM EC011860 FAQ What insert type is required for this cutter? The cutter uses WNGX 0403 indexable inserts; the S945TM is designed specifically for this insert geometry and accepts common Korloy variants. How is the insert secured in the cutter? Inserts are held with a Torx clamping screw (size M2.5x5.5) tightened with a T8 key to ensure secure seating under cutting forces. What shank size is recommended for toolholders? The tool features a 25 mm shank diameter; holders or collets matched to this diameter are recommended for optimal clamping and run-out control. Is the S945TM suitable for heavy-duty roughing? With four cutting edges and a rigid shank, the tool is suitable for many heavy removal tasks within the limits of the selected insert grade and machine power. Can the cutter be used with inserts from other manufacturers? Compatibility is stated for WNGX 0403 inserts; many manufacturers, including Korloy, offer matching grades and geometries that fit the same seat and clamping style. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank End Mill For XOMX 1204 Indexable Inserts, 3 Flutes, 60mm Cutting Length - Teknik Makina
Take advantage of a rigid 25 mm shank and a 60 mm cutting length for stable, repeatable machining; combined with compatibility for XOMX 0602‑1204 indexable inserts this tool offers efficient tool changes and reliable surface finishes. Order via Metav Werkzeuge for dependable supply or request advice from our consultants for process integration. Shank cutter S644TM — 25 mm shank, 3 cutting edges, for XOMX 0602‑1204 indexable inserts (Teknik Makina) The Shank cutter S644TM is a robust indexable milling tool designed for precise face and shoulder machining in production environments, compatible with XOMX 0602‑1204 indexable inserts. 25 mm shank diameter for rigid clamping 60 mm cutting length for deeper passes Compatible with XOMX 0602‑1204 indexable inserts Torx M3.5×8.5 fixing screw, T10 key Precision and stiffness for consistent component quality With a 25 mm shank and a substantial overall length of 200 mm, this cutter provides the structural stiffness required for repeatable results on medium‑duty milling operations. The combination of a solid shank and an optimised cutting length reduces vibration and uneven tool wear, which supports improved surface finish and longer service intervals. The tool’s mass (approx. 0.779 kg) contributes to a stable running condition, allowing machine settings to be kept consistent and reducing the need for constant compensation during production. Fast indexable system to lower machining costs Designed for XOMX 0602‑1204 inserts (compatible with SECO insert systems), the cutter uses a three‑edge insert layout and a secure Torx M3.5×8.5 fixing screw operated with a T10 key, enabling quick, repeatable insert changes. This indexable approach separates the cutting geometry from the tool body, so worn cutting edges can be replaced rapidly without full tool replacement. The result is reduced downtime, predictable running costs and a clear path to higher productivity in batch production. Easier set‑up and predictable machining behaviour A 90° cutting angle supports square shoulders and accurate step milling, making the tool suitable where perpendicular faces and tight tolerances are required. The three cutting edges are balanced for smooth engagement, which simplifies feed and speed selection and helps protect both spindle and fixture from undue loads. Installation requires only a standard 25 mm holder and the supplied Torx interface, allowing straightforward integration into existing tool magazines and changeover routines without complex adaption. For professional indexable milling with a rigid 25 mm shank, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich — technical consultation and ordering support are available. Technical data SKU: S644TM Manufacturer: Teknik Makina Designation: Shank cutter for XOMX 0602‑1204 indexable inserts Compatible insert manufacturer: SECO Facts Shaft diameter: 25 mm Cutting length: 60 mm Overall length: 200 mm Cutting edges: 3 Weight: 0.779 kg Cutting angle: 90° Special features Torx fixing screw: M3.5×8.5 Torx key size: T10 Suitable for XOMX 0602‑1204 indexable inserts Indexable system for rapid insert changes FAQ Which indexable inserts fit this cutter? The shank cutter S644TM accepts XOMX 0602‑1204 indexable inserts; compatibility with SECO‑type inserts is specified for straightforward sourcing. What are the key dimensions to check for holder compatibility? Check for a 25 mm shank acceptance in the tool holder and a 200 mm overall length; the S644TM requires a holder that secures a 25 mm shank. How are the inserts secured to the cutter? Inserts are clamped with a Torx M3.5×8.5 screw; a T10 key is used for secure and repeatable fastening on the S644TM. How many cutting edges does the tool have and what is the tool angle? The tool is designed with 3 cutting edges and a 90° cutting angle, which is effective for square shoulder milling and controlled material removal. Is the cutter suitable for different materials? Material suitability depends primarily on the selected insert grade; the S644TM provides the rigid interface and geometry for a wide range of applications when combined with the appropriate XOMX insert grades. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter For APKT 1705 Indexable Inserts, 2 Flutes 60mm Cutting Length - Teknik Makina
Take advantage of the cutter's combination of rigid shank design and straightforward insert system to boost throughput and reduce tool-change time; order directly via Metav Werkzeuge or consult the team for application advice. Schaftfräser S660-1TM – shank-mounted milling cutter for APKT 1705 indexable inserts by Teknik Makina The Schaftfräser S660-1TM is a shank-mounted milling cutter engineered for stable, repeatable metal removal using APKT 1705 indexable inserts in industrial workshop environments. 25 mm shank diameter for rigid clamping 60 mm cutting length for deeper engagement Compatible with APKT 1705 indexable inserts Torx M4x10 screw and T15 key High productivity through a rigid shank and compact geometry The S660-1TM delivers increased productivity by combining a 25 mm shank with a medium-length cutting zone. The larger shank diameter reduces deflection during heavy cuts, enabling higher feed rates and more consistent chip formation. With 60 mm cutting length and 2 cutting edges, the tool balances material removal rate and surface finish; the limited number of edges simplifies balancing and can lower cutting forces compared with multi-flute alternatives. This improves process stability on horizontal and vertical milling spindles, helping maintain cycle times and part tolerances in serial production. Proven insert system for economical operation and predictable results Designed for the APKT 1705 insert family, the holder benefits from the widespread availability and repeatability of indexable inserts. Using standard indexable inserts reduces tooling inventory complexity and shortens downtime for regrinds or replacements. Compatibility with Taegutec inserts ensures access to a broad range of grades and geometries for different alloy classes and machining tasks. The modular insert concept permits fine-tuning of edge geometry and coating selection on the insert itself without replacing the complete tool, lowering cost per component over time. Quick, secure fastening and workshop-friendly handling Assembly and insert changes are straightforward with the specified Torx M4x10 fastening and T15 key interface, enabling repeatable clamp torque and fast exchange routines. The tool’s 200 mm overall length and a mass of 0.763 kg provide a practical balance between overhang and rigidity; the moderate weight helps preserve spindle bearings and simplifies manual handling during set-up. The compact fastening arrangement minimises the risk of insert movement under load, contributing to consistent part quality and predictable tool life. Ideal fit for mixed-production workshop environments This shank-mounted cutter suits facilities that require a dependable, easy-to-service solution for medium-engagement milling tasks. Its construction supports batch work, repair operations and light series production where rapid insert changes and straightforward inventory management are priorities. The tool’s clear specification for APKT 1705 inserts simplifies procurement planning and integration into existing tool libraries, whilst the robust shank offers an immediate advantage when stability under load is essential. For application-specific guidance, stock availability or to discuss suitable insert grades for particular materials, contact Metav Werkzeuge – Metav provides precise tools with reliable supply from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical details Article number: S660-1TM Manufacturer: Teknik Makina Name: Schaftfräser for APKT 1705 Indexable Inserts Core data Shaft diameter: 25 mm Cutting length: 60 mm Overall length: 200 mm Weight: 0.763 kg Cutting edges: 2 Design & features Compatible with APKT 1705 indexable inserts Suitable inserts manufacturer: Taegutec Torx M4x10 screw T15 key FAQ What insert type does this cutter accept? The S660-1TM accepts APKT 1705 indexable inserts; compatibility with Taegutec inserts is specified in the product data for easy sourcing. How does the 25 mm shank benefit machining stability? A 25 mm shank increases clamping rigidity and reduces deflection, which improves repeatability and enables higher feeds compared with smaller-diameter holders. Are the fastening tools included with the cutter? The technical specification lists a Torx M4x10 screw and T15 key for fastening; these details define the secure clamp interface used when replacing inserts. Is the tool suitable for long-overhang milling? With a 200 mm overall length and a robust shank, the tool is suitable for moderate overhangs; for extensive overhangs, assess fixture rigidity and cutting parameters to maintain process stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Shank Milling Cutter For APMT 1604 Indexable Inserts, 2 Flutes 90° Cutting Angle - Teknik Makina
Take advantage of a compact, robust milling solution that pairs a stable 25 mm shank with APMT 1604 indexable inserts for efficient face and slot milling; the result is consistent metal removal rates and predictable tool life. Order the cutter directly via Metav Werkzeuge or ask the consultants for compatibility advice and delivery options. S245TM Shank Milling Cutter — for APMT 1604 indexable inserts, 25 mm shank (Teknik Makina) A S245TM shank milling cutter engineered for indexable‑insert milling tasks, optimised for face and slot milling where quick insert changes and repeatable clamping are required 25 mm shank diameter for stable clamping Two cutting edges for balanced performance Compatible with APMT 1604 indexable inserts Torx clamping screw M4x10 and T15 key included High, predictable metal removal and repeatable geometry The design combines a 25 mm shank with a 55 mm cutting length to offer a stable toolholder interface and an effective reach for typical slotting and facing operations. With two cutting edges and a 90° cutting angle, the body provides a neutral cutting geometry that helps maintain consistent chip evacuation and surface finish when paired with the correct insert grade. This configuration supports steady cycle times and reduces the need for rework, helping production planners achieve reliable throughput without sacrificing component quality. Fast insert changes and secure clamping to reduce downtime Clamping is achieved with a M4x10 Torx screw operated with a T15 key, allowing quick and repeatable insert replacement at the machine. The simple Torx system reduces changeover time and limits variability introduced during tightening, which in turn supports consistent tool life across shifts. The cutter body’s balanced architecture and modest mass (0.61 kg) make it straightforward to handle during setup while still providing sufficient rigidity for routine milling tasks. Versatile workshop use and economical tool management As an indexable‑insert solution compatible with APMT 1604 plates and insert brands such as Korloy, the cutter separates the cutting edge cost from the body cost: insert grades can be selected to match steel, aluminium or finishing requirements while the shank body remains in service. The 150 mm overall length and compact profile make it suitable for standard milling setups where accessibility and tool change speed are priorities. For industrial workshops seeking predictable supply and traceable quality, a modular approach of body plus insert simplifies inventory and lowers running costs over time. Contact Metav Werkzeuge for tailored advice on insert grades, delivery times and to confirm compatibility with existing toolholders; Metav Werkzeuge can arrange prompt dispatch from Emmerich and provide technical guidance for workshop integration Technical details SKU: S245TM Brand: Teknik Makina Product: Shank milling cutter for APMT 1604 indexable inserts Core dimensions Shank diameter: 25 mm Cutting length: 55 mm Overall length: 150 mm Number of cutting edges: 2 Weight: 0.61 kg Cutting angle: 90° Materials & features Compatible inserts: APMT 1604 Compatible insert manufacturer: Korloy Torx clamping screw: M4x10 Torx key size: T15 FAQ Which inserts fit this cutter? The S245TM accepts APMT 1604 indexable inserts; insert selection should match the material and finish requirements and can be sourced from brands such as Korloy. How are the inserts secured? Inserts are clamped with an M4x10 Torx screw; the specified key size for tightening is T15 to ensure repeatable clamping torque. What applications suit this cutter? The body is designed for general face and slot milling where indexable inserts are preferred; the neutral 90° cutting geometry supports a range of roughing and finishing tasks when the correct insert grade is fitted. What are the physical dimensions and mass? Key dimensions: 25 mm shank diameter, 55 mm cutting length, 150 mm overall length; mass approximately 0.61 kg. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter For BDMT 11T3 Indexable Inserts, 3 Teeth, 60mm Cutting Length - Teknik Makina
Take advantage of a rigid Ø25 mm shank and a 60 mm effective cutting length for stable, repeatable milling and reduced spindle load; combine this with quick insert changes for efficient workshop throughput. Order the tool directly via Metav Werkzeuge or consult our specialists for application guidance. Shank milling cutter S570TM — Ø25 mm shank, for BDMT 11T3 indexable inserts (Teknik Makina) The Shank milling cutter S570TM is a dedicated indexable-insert tool designed for reliable milling operations; it combines a solid 25 mm shank with a 60 mm cutting length to deliver stability and repeatable results in production and repair environments. Ø25 mm shank for rigid clamping 60 mm effective cutting length Compatible with BDMT 11T3 Kyocera inserts Secure Torx M2.5x5.5 clamp, T8 key Stable clamping and reduced vibration for consistent surface finish With a Ø25 mm shank and a total length of 200 mm, this cutter is engineered for rigidity where it matters. The combination of a substantially dimensioned shank and a 60 mm cutting length reduces deflection under load, which in turn improves surface finish and dimensional repeatability. The tool's mass (approx. 0.764 kg) and three cutting edges help distribute cutting forces evenly; this lowers spindle stress and supports longer cycle times without compromising workpiece accuracy. For production environments seeking predictable machining results, the mechanical stability is a clear operational advantage. Fast, secure insert changes minimise downtime The cutter accepts BDMT 11T3 indexable inserts and is compatible with Kyocera-style plates, allowing proven insert grades to be used for different materials and finishes. Clamping is carried out with a Torx M2.5x5.5 screw secured using a T8 key, a common workshop standard that enables quick, repeatable seating of the insert and straightforward replacement during shift changes. The indexable system reduces tooling cost per cutting edge and accelerates maintenance routines — a rational benefit for both jobbing shops and serial production where uptime is critical. Designed for practical workshop flexibility and straightforward handling A 90° cutting angle provides effective shoulder milling and simple programming for CNC fixtures, while the three-edge configuration balances cutting performance and tool economy. The indexable approach allows a single holder to serve multiple tasks by changing insert geometry or grade rather than the whole cutter, simplifying inventory and tooling logistics. In short, the tool provides a pragmatic mix of performance and serviceability that supports both high-mix work and standard production runs, helping to streamline operational workflows without complex retooling. For Teknik Makina quality and a tailored application consultation, contact Metav Werkzeuge for expert advice and reliable supply directly from Emmerich Technical data Article number: S570TM Manufacturer: Teknik Makina Compatible inserts: BDMT 11T3 Facts Shank diameter: 25 mm Cutting length: 60 mm Overall length: 200 mm Weight: 0.764 kg Cutting edges: 3 Cutting angle: 90° Special features Torx screw: M2.5x5.5 Torx key: T8 Compatible with Kyocera inserts Indexable-insert system FAQ Which indexable inserts fit this cutter? The cutter is designed for BDMT 11T3 indexable inserts; Teknik Makina’s S570TM accepts these inserts and is compatible with Kyocera-manufactured plates for flexible grade selection. How is the insert secured in the holder? Inserts are clamped with a Torx M2.5x5.5 screw; a T8 key is used for tightening, providing a secure, repeatable seat for each insert on the S570TM. What machining benefits does the 25 mm shank provide? A Ø25 mm shank increases rigidity and reduces deflection during cuts; the resulting stability improves surface finish and dimensional consistency on the workpiece. Is the S570TM suitable for shoulder milling? Yes—the 90° cutting angle and three cutting edges make the tool well suited to shoulder milling operations where square faces and reliable tool paths are required. Can different insert grades be used for varying materials? Yes; the indexable system of the S570TM allows the use of different insert grades compatible with BDMT 11T3 geometry to match material and finish requirements. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter For ENMX 0604 Indexable Inserts, 4 Flutes, 180mm Overall Length - Teknik Makina
Benefit from the combination of a 25 mm shank, compatibility with ENMX 0604 indexable inserts and a four‑edged cutting configuration to secure high removal rates and predictable cycle times. Order the S112TM directly via Metav Werkzeuge or ask the technical consultants for application advice. Milling cutter S112TM — 25 mm diameter, 4 cutting edges (Teknik Makina) The Milling cutter S112TM is a shank-mounted milling cutter intended for CNC milling operations using ENMX 0604 indexable inserts, offering a balance of rigidity and reach for standard production tasks Designed for ENMX 0604 indexable inserts 25 mm shank diameter for high rigidity Four cutting edges for efficient machining Torx M2.5x7 clamping screw, T8 key required Faster cycles through optimised cutter geometry The S112TM combines a 25 mm diameter and four cutting edges to increase material removal per pass while maintaining a stable cutting action. Using indexable inserts (ENMX 0604) reduces downtime for tool changes because worn edges are replaced rather than the whole tool, which shortens non-productive periods and improves throughput. The geometry is chosen to provide consistent chip evacuation and predictable surface interaction, so machining parameters can be standardised across batches, supporting reproducible cycle times and simplified process planning. Secure clamping and easy insert handling for steady production Insert retention is achieved with an M2.5x7 Torx clamping screw tightened with a T8 key, which ensures reproducible clamping force and quick, repeatable insert swaps. The 25 mm shank enhances rigidity; reduced deflection is the direct result, which in turn supports dimensional accuracy during facing, slotting or shoulder milling operations. With an 180 mm overall length, the tool provides practical reach while keeping vibration and chatter in check. The clamping arrangement is designed so that maintenance is straightforward and replacement parts follow standardised sizes. Integrates smoothly into indexable-insert workflows Compatibility with ENMX 0604 inserts and proven fit for YG-1 insert geometries makes the cutter a flexible choice for job shops and production cells that rely on indexable tooling. The tool is manufactured in line with industry machining standards, and is intended for integration into holders and spindles that accept a 25 mm shank. The result is a reliable, serviceable component of a larger tooling system that supports consistent output quality and predictable tool-change intervals, making it suitable for mixed-production environments where uptime and repeatability are priorities. Contact Metav Werkzeuge for tailored technical guidance and sourcing of the Teknik Cutting Tools S112TM milling cutter — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: S112TM Article: for ENMX 0604 Indexable Inserts Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Facts Diameter: 25 mm Shank diameter (aufnahme): 25 mm Overall length: 180 mm Cutting edges: 4 Special features For ENMX 0604 indexable inserts Compatible with inserts by YG-1 Torx clamping screw M2.5x7 Torx key size T8 FAQ Which indexable inserts fit this cutter? The cutter accepts ENMX 0604 indexable inserts and is compatible with inserts produced by YG-1. What are the main dimensions and cutting configuration? The tool has a nominal 25 mm diameter and shank, an 180 mm overall length and 4 cutting edges for efficient material removal. How is the insert secured in the cutter? Insert retention is via an M2.5x7 Torx clamping screw; a T8 key is used for tightening and release. Is this cutter suitable for production environments? The design targets CNC milling workflows where quick insert changes and stable cutting performance support repeatable production results. Manufacturer / Responsible: Teknik Cutting Tools; Buyukkayacık OSB Mah. 422 Nolu Sokak No: 9, Selcuklu/KONYA, Turkey / Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Shank Milling Cutter for ENMX 0604 Indexable Inserts, 4 Teeth, 140mm - Teknik Makina
Take advantage of the combination of reliable clamping stability, quick indexable‑insert changes and robust construction for uninterrupted milling productivity; order the tool directly via Metav Werkzeuge or consult the specialists for process-specific advice. Schaftfräser S111TM — Indexable‑insert shank cutter with 25 mm shank A Schaftfräser S111TM designed for versatile milling with ENMX 0604 indexable inserts, suited to CNC machining and workshop applications 25 mm shank diameter for stable clamping Four cutting edges for balanced material removal Compatible with ENMX 0604 indexable inserts Torx M2.5x7 screw; key size T8 Stable toolholding for consistent surface quality The S111TM delivers stable clamping through its robust 25 mm shank, minimising vibration and promoting repeatable tool paths. The tool’s geometry with 4 cutting edges balances cutting forces, which reduces cyclical load on the spindle and contributes to a more even surface finish. For production environments where process stability equals throughput, this configuration helps to decrease scrap rates and maintain tight tolerances over longer runs. Fast insert changes and secure fixing for uptime Designed for use with ENMX 0604 indexable inserts, the cutter supports rapid insert replacement to reduce machine downtime. Compatibility with YG‑1 inserts ensures access to a wide range of grades and geometries. The insert is secured by a Torx M2.5x7 screw and requires a T8 key for tightening, providing reliable clamping force and straightforward serviceability without specialised fixtures. This arrangement supports efficient shift changes and predictable maintenance intervals. Versatile use across general milling tasks This shank cutter is intended for a variety of milling operations in conventional and CNC environments, offering flexibility for both roughing and semi‑finishing when paired with suitable inserts. The tool’s overall length of 140 mm and compact diameter support machining in constrained setups while still providing adequate reach. Operators benefit from straightforward tool selection and a predictable cutting behaviour that integrates well into established machining cycles. Efficiency gains and measurable cost benefits By using indexable inserts, the cutter reduces per‑edge tooling costs and simplifies inventory management compared with solid carbide alternatives. The modularity of the system allows for targeted grade selection to match workpiece materials, helping to extend tool life and lower running costs. Combined with Metav’s supply reliability and technical advice, this results in a pragmatic solution for workshops seeking both productivity and maintainability. For precision milling backed by dependable clamping, contact Metav Werkzeuge in Emmerich for tailored advice and prompt supply of the S111TM — Metav Werkzeuge is ready to support specification and delivery via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: S111TM Manufacturer: Teknik Makina Core dimensions Shank diameter: 25 mm Cutter diameter: 25 mm Overall length: 140 mm Number of cutting edges: 4 Compatibility & features For ENMX 0604 indexable inserts Compatible insert brand: YG‑1 Torx screw: M2.5x7 Torx key size: T8 Brand: Teknik Makina FAQ What insert type does this cutter accept? The cutter accepts ENMX 0604 indexable inserts; the S111TM is configured to work with this insert size for quick replacement and predictable cutting geometry. Which screw and tool are required to secure the insert? Insert clamping uses a Torx M2.5x7 screw and the corresponding T8 key for reliable fixation as supplied in standard workshop toolkits. Is the cutter suitable for heavy roughing operations? The tool’s four‑edge design and 25 mm shank provide balanced cutting forces; for heavy roughing, selecting the correct insert grade and machining parameters is recommended to match the workpiece and machine capabilities. Can the cutter be used with YG‑1 inserts? Yes, the tool is compatible with YG‑1 inserts, allowing access to a range of carbide grades and chipbreaker options for different materials. What benefits do indexable inserts provide compared with solid tools? Indexable inserts reduce per‑edge costs, enable rapid on‑machine index changes and simplify stocking of cutting grades, resulting in lower downtime and better cost control over production cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter for LNMT 0804 Indexable Inserts, 4-Flute 40mm Cutting Length - Teknik Makina
The combination of a 25 mm shank, compatibility with LNMT 0804 indexable inserts and a 40 mm effective cutting length ensures consistent material removal and straightforward retrofit into existing holders. Order the S303TM Shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed. S303TM Shank milling cutter — 25 mm shank, for LNMT 0804 indexable inserts (Teknik Makina) The S303TM Shank milling cutter is a purpose-built tool for indexable LNMT 0804 inserts, offering a compact 25 mm shank and a 40 mm cutting length for reliable milling operations in CNC and toolroom environments. 25 mm shank diameter for rigid clamping Compatible with LNMT 0804 indexable inserts Four cutting edges for stable cutting performance Torx M2.5x7 clamp screw with T8 key Reliable rigidity and reproducible results A 25 mm shank provides mechanical stiffness that reduces deflection under load, translating into improved surface finish and dimensional repeatability. The solid shank diameter and 150 mm overall length combine to deliver a balance between reach and stability, making the tool suitable for setups where consistent runout control is required. For operations that demand predictable tool behaviour, the machining geometry reduces vibration and supports tighter tolerances. Compatibility that simplifies procurement and setup Designed for LNMT 0804 indexable inserts and compatible with ISCAR insert geometries, the cutter streamlines inventory and reduces downtime when changing insert types. The use of a standard Torx M2.5x7 clamp screw and T8 key enables quick insert changes and secure fixation, lowering setup time and supporting a faster changeover routine. Specified interface dimensions ensure reliable seating of the insert and repeatable positioning cycle after each index. Focused cutting capacity with stable edges Equipped with four cutting edges, this shank cutter maintains an even load distribution across the tool periphery. The 40 mm effective cutting length keeps the engagement zone compact, which benefits tool life and chip evacuation in many milling tasks. For shops aiming to combine throughput with predictable maintenance intervals, the geometry helps achieve efficient material removal while controlling cutting forces. Practical handling and workshop integration At 0.601 kg, the cutter is robust without being cumbersome, making handling and fixture loading straightforward on manual and CNC machines alike. The 25 mm mounting diameter aligns with common toolholders, easing integration into existing tool assemblies. Where operators require dependable repeatability, the cutter’s dimensions and fastening system support efficient replacement and minimal retraining. Contact Metav Werkzeuge today to discuss the Teknik Makina S303TM shank milling cutter, confirm compatibility with current toolholders and secure fast delivery from our Emmerich centre Technical data Article number: S303TM Manufacturer: Teknik Makina Compatible inserts: LNMT 0804 Compatible insert manufacturer: ISCAR Shank diameter: 25 mm Mounting diameter: 25 mm Core specifications Cutting length (effective): 40 mm Number of cutting edges: 4 Overall length: 150 mm Weight: 0.601 kg Features Clamp screw: M2.5x7 (Torx) Torx key size: T8 Tool type: Shank milling cutter Application: Indexable insert milling FAQ Which inserts fit this cutter? The S303TM accepts LNMT 0804 indexable inserts; compatibility with ISCAR geometries is specified for straightforward replacement. What is the shank diameter and how does it affect stability? The tool has a 25 mm shank, which provides high rigidity for reduced deflection and improved surface tolerances. How many cutting edges does the cutter have and what is the benefit? The cutter features four cutting edges, offering a balanced cutting load and consistent material removal for improved tool life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter For LNMU 0303 Indexable Inserts 4 Flutes, 150mm Length - Teknik Makina
Take advantage of a compact, insert-based design that combines reliable 25 mm rigidity with a 150 mm overall length for stable milling and straightforward insert replacement; order via Metav Werkzeuge or consult the team for application advice. Schaftfräser S675TM — shank milling cutter, 25 mm diameter, for LNMU 0303 indexable inserts by Teknik Makina The Schaftfräser S675TM is a shank milling cutter designed for use with LNMU 0303 indexable inserts, offering a robust mounting solution for repeatable milling operations in production and toolroom environments. 25 mm shank diameter 150 mm overall length 4 cutting edges for balanced cutting Compatible with LNMU 0303 indexable inserts Secure insert mounting for consistent accuracy The tool features a precision-machined pocket for LNMU 0303 indexable inserts and is retained with an M2.5x7 Torx screw driven by a T8 key, which ensures secure clamping and minimal play during rotation. This fastening arrangement reduces radial runout and improves positional repeatability, translating into fewer rejected parts and less rework. For operations relying on indexed insert changes, the proven connection method shortens tool-change intervals while maintaining cutting accuracy. Stable geometry for efficient material removal With 4 cutting edges and a 25 mm shank, the cutter combines rigidity with a chip-forming geometry that supports steady cutting forces and improved surface finish. The overall length of 150 mm provides reach where required without sacrificing stability, enabling higher feed rates on compatible machines. The multi-flute arrangement balances chip evacuation and cutting load, so machining cycles benefit from efficient material removal and a predictable tool life pattern. Inventory and workflow benefits for production shops Compatibility with the LNMU 0303 insert family and the TNGLY‑OKE insert range simplifies stock management and reduces the variety of holders and cutters required in the workshop. The indexable design means only the insert needs replacing when worn, lowering per-cutting-edge cost and easing maintenance planning. As a workshop-grade solution from Teknik Makina, the cutter supports standardised tooling strategies that help maintain throughput and reduce downtime. For secure, high-performance milling with Teknik Makina tools, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich: call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: S675TM Product name: Shank milling cutter for LNMU 0303 indexable inserts Manufacturer: Teknik Makina Numbers / Core technical data Diameter: 25 mm Overall length: 150 mm Shank diameter (clamping): 25 mm Number of cutting edges: 4 Torx screw: M2.5x7 Special features / Versions Compatible inserts: LNMU 0303 Compatible insert manufacturers: TNGLY-OKE Torx key size: T8 Indexable-insert design for insert replacement FAQ What inserts fit this shank milling cutter? The S675TM is designed for LNMU 0303 indexable inserts and is compatible with inserts listed under the TNGLY‑OKE designation. How is the insert secured in the cutter? Insert retention is achieved with an M2.5x7 Torx screw; the screw is tightened using a T8 key to ensure secure clamping of the indexable insert in the cutter pocket. Is this cutter suitable for heavy roughing? The S675TM’s 25 mm shank and four cutting edges provide rigidity suitable for many general milling tasks; suitability for heavy roughing depends on machine power and specific cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter for R390 18 Indexable Inserts Internal Coolant, 60mm Cutting Length - Teknik Makina
Take advantage of a robust milling solution that combines precise compatibility with Sandvik R390 18 indexable inserts, efficient chip and coolant management through internal coolant, and a stable 25 mm shank for consistent machining results; order the module directly via Metav Werkzeuge or consult our experts for application support. S603-1TM – 25 mm shank indexable milling cutter body for R390 18 inserts with internal coolant (Teknik Makina) A S603-1TM cutter body engineered for insert milling applications, offering a 150 mm overall length and targeted coolant delivery for improved tool life and process reliability. Internal coolant for reliable chip evacuation Compatible with Sandvik R390 18 inserts 25 mm shank for standard toolholders 60 mm cutting length, 150 mm overall length Greater stability and predictable machining results The combination of a 25 mm shank and a balanced overall length of 150 mm provides increased rigidity compared with smaller shank diameters, which translates into reduced vibration and more consistent surface finish. The tool’s mass (approx. 0.531 kg) contributes to stable rotation at typical milling speeds, helping to maintain dimensional accuracy during interrupted cuts. For workshops and production lines seeking reproducible results, the robust design of this cutter body supports repeatable set-ups and fewer reworks. Faster indexable insert changes and straightforward maintenance Designed to accept Sandvik R390 18 indexable inserts, the body simplifies insert replacement and maintenance procedures. Fast clamping is enabled by standard Torx hardware (Torx key T15, screw M4x10), reducing tool change time and machine downtime. The unit holds two cutting edges, permitting economical use of indexable inserts while preserving process flexibility. Clear access to the fixing screws and a logical arrangement of the insert seats make routine checks and regrinds efficient for workshop staff. Integrated coolant for extended tool life and stable cutting The internal coolant channel directs lubricant and coolant close to the cutting zone, which promotes heat dissipation and improved chip control. This targeted coolant supply supports longer insert life and can help stabilise cutting forces in heavy-duty operations, especially where consistent temperature control matters. The tool body is therefore suitable for organised production environments that prioritise tool longevity and operational uptime while maintaining simple handling and quick insert swaps. Discuss specific machining requirements with Metav Werkzeuge and request availability of the Teknik Makina S603-1TM cutter body with internal coolant via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data SKU: S603-1TM Product type: Indexable milling cutter body (for R390 18 inserts) Brand: Teknik Makina Compatible inserts: Sandvik R390 18 eClass: 21180806 Core dimensions Shank diameter: 25 mm Cutting length (shank): 60 mm Overall length: 150 mm Number of cutting edges: 2 Weight: 0.531 kg Design & special features Internal coolant Torx key: T15 Torx screw: M4x10 For use with Sandvik R390 18 indexable inserts FAQ Is this cutter body compatible with Sandvik R390 18 inserts? Yes. The S603-1TM is designed specifically for use with Sandvik R390 18 indexable inserts. What shank size is required for mounting? The tool features a 25 mm shank diameter, suitable for toolholders accepting 25 mm shanks. How long is the cutting zone and the overall tool? The cutting length (shank) is 60 mm and the overall length is 150 mm. How many inserts does the body hold? The holder is configured for two cutting edges/inserts. Which fastening hardware is used for the inserts? Insert clamping uses a Torx T15 key and M4x10 screws. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter for RDMT 1003 Indexable Inserts, 2 Flutes 50mm Cutting Length - Teknik Makina
Take advantage of a compact, robust milling solution that pairs stable clamping with efficient indexable-insert performance; the combination of a Ø25 mm shank and a 50 mm effective cutting length supports consistent material removal and predictable tool life. Order directly via Metav Werkzeuge or consult Metav's specialists for fitment and application advice. Shank milling cutter R192TM – for RDMT 1003 indexable inserts, Ø25 mm shank The Shank milling cutter R192TM is a precision tool holder designed for machining with RDMT 1003 indexable inserts, providing a compact overall length for space-constrained set-ups and reliable mounting for light to medium milling operations Ø25 mm shank for stable clamping Compatible with RDMT 1003 indexable inserts 50 mm effective cutting length Torx fixing M3.5x8.5, key T15 Rigidity and repeatability for consistent machining results The tool's Ø25 mm shank and compact overall length 120 mm are engineered to reduce deflection in clamped setups, which promotes dimensional consistency across batches. A rigid holder reduces vibration and improves surface finish when compared with slender holders; this benefit is particularly relevant for short-run production and reaming-adjacent milling tasks where positional accuracy matters. The modest mass of 0.435 kg keeps toolchanger dynamics predictable while maintaining sufficient stability for controlled chip formation and tool life. Optimised for indexable inserts and clear performance gains Compatibility with RDMT 1003 indexable inserts allows quick insert changes and straightforward toolroom stocking. The cutter provides an effective cutting length of 50 mm and is configured with 2 cutting edges, balancing metal removal rates and economical insert usage. Using indexable geometry designed for interrupted cuts or grooving reduces downtime for edge replacement and enables targeted performance tuning: selecting the appropriate insert grade yields either extended life or higher cutting speed according to the workpiece requirements. Simple assembly and secure clamping save workshop time Fast and secure insert retention is achieved via a locking screw M3.5 and a Torx screw M3.5x8.5, tightened with a T15 key, ensuring consistent seat pressure and repeatable positioning of each insert. This straightforward fastening arrangement simplifies maintenance routines and minimises set-up time when replacing inserts or performing inspections. The design emphasises practical handling and reduces the number of special tools required in the tool store while preserving the cutter's mechanical integrity. For machining setups that demand reliable insert mounting and compact tool length, consider the Teknik Makina R192TM shank milling cutter and contact Metav Werkzeuge for tailored application guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: R192TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Dimensions & weights Shank diameter: 25 mm Cutting length: 50 mm Overall length: 120 mm Number of cutting edges: 2 Weight: 0.435 kg Features & fittings Compatible inserts: RDMT 1003 Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 FAQ Is this cutter compatible with RDMT 1003 inserts? Yes. The R192TM is specified for RDMT 1003 indexable inserts and is engineered to accept that insert format. How many cutting edges does the tool provide and what is the cutting length? The holder is configured with 2 cutting edges and an effective cutting length of 50 mm for focused engagement. What are the key fastening components for insert retention? Insert retention uses a locking screw M3.5 together with a Torx screw M3.5x8.5, tightened using a T15 key as supplied with standard workshop tool sets. What shank diameter and overall length does the cutter have? Shank diameter is 25 mm and the overall length of the assembly is 120 mm, offering a compact footprint for many milling configurations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Shank Milling Cutter for RPMT 0803 Indexable Inserts With Internal Coolant, 150mm - Teknik Makina
Take advantage of the combination of rigid clamping, targeted coolant delivery and proven indexable insert compatibility for reliable milling cycles; order direct via Metav Werkzeuge or consult our specialists for application-specific advice. Indexable shank cutter R313-1TM — 25 mm shank, internal coolant (Teknik Makina) A shank cutter R313-1TM for precision indexable milling with RPMT 0803 inserts, designed for stable toolholding and coolant-through performance in demanding workshop applications 25 mm shank diameter for stable toolholding Internal coolant for improved chip evacuation Compatible with RPMT 0803 Korloy inserts 150 mm overall length for deep reach Four cutting edges for balanced cutting Predictable rigidity and repeatable clamping for machining stability A firm foundation for any milling task is a consistent clamping system. The cutter’s 25 mm shank provides high radial stiffness and reduces vibration in typical toolholders, which translates into improved surface finish and extended insert life. With a mass of 0.591 kg, the tool offers a balance between stability and dynamic response, helping to maintain feed rates and tolerances on longer passes. This mechanical reliability supports efficient production where repeatability matters. Coolant-through design to control heat and clear chips Internal coolant is integrated to support temperature control at the cutting edge and to evacuate chips from the cut. The internal coolant channel helps to reduce thermal loading on the inserts and workpiece, which preserves edge geometry and reduces the frequency of insert changes. For operations that demand consistent cycle times and minimal rework, coolant-through capability is a practical investment in process reliability and tool life optimisation. Flexible indexable insert system for efficient tool management The cutter accepts RPMT 0803 indexable inserts and is listed as compatible with Korloy inserts, enabling rapid index changes and flexible grade selection for varied materials. With four cutting edges, the geometry delivers balanced engagement and smooth cutting forces, while the fastening uses an M3x7 Torx screw requiring a T8 Torx key for secure seating. This modular approach reduces tool inventory complexity and allows focus on optimal insert grade selection per application. Practical dimensions that integrate into existing setups With a 150 mm overall length and a 35 mm cutting length, the tool reaches into pockets and deeper features while maintaining a compact working profile. The specified dimensions make the cutter suitable for many standard milling setups, from finishing passes to more robust material removal, without excessive overhang. The SKU R313-1TM and compact weight make it straightforward to document and manage in tool libraries and ERP systems. For precise indexable milling with internal coolant, contact Metav Werkzeuge to discuss the Teknik Makina R313-1TM and secure the right toolholding solution for the workshop — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: R313-1TM Manufacturer: Teknik Makina Label: 25mm shank cutter RPMT 0803 L150mm with internal coolant Core dimensions Diameter: 25 mm Overall length: 150 mm Shank diameter: 25 mm Cutting length: 35 mm Weight: 0.591 kg Features & compatibility Internal coolant Compatible with RPMT 0803 inserts Suited to Korloy RPMT 0803 inserts Four cutting edges Torx screw M3x7 Torx key size T8 FAQ Which insert type fits this cutter? The cutter accepts RPMT 0803 indexable inserts; Korloy grades are listed as compatible for flexible grade selection. What secures the inserts in place? Inserts are fastened with an M3x7 Torx screw; a T8 Torx key is required for tightening. Is the tool suitable for deep-pocket milling? The 150 mm overall length and 35 mm cutting length allow reach into deeper pockets while keeping overhang within practical limits for stable machining. How many cutting edges are available per rotation? The tool is configured with four cutting edges, providing balanced cutting forces and smooth engagement. What should be considered for toolholders? A rigid clamping system matching the 25 mm shank diameter is recommended to exploit the cutter’s stiffness and maintain surface quality. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter for RPMW 0803 Indexable Inserts, 4 Cutting Edges - Teknik Makina
Take advantage of the combination of effective insert clamping, a standard 25 mm shank and a compact 150 mm overall length for reliable milling cycles; order directly via Metav Werkzeuge or consult the technical team for application support. Insert milling cutter — 25 mm shank, for RPMW 0803 indexable inserts (Teknik Makina) Insert milling cutter for RPMW 0803 indexable inserts, designed as a robust cutter body for light to medium milling tasks where fast insert changes and predictable performance are required 25 mm shank diameter for stable clamping 150 mm overall length for accessible reach Fits RPMW 10T3 indexable inserts Four cutting edges for efficient material removal Increased productivity through a proven insert system The cutter body is designed around the RPMW 0803 insert form, enabling quick insert replacement and predictable cutting performance. By using indexable inserts such as RPMW 10T3, running costs are reduced because only the insert is exchanged when worn, not the entire tool. The fixed geometry of the holder ensures consistent chip control and reduces downtime during tool changes. This makes the tool especially suitable for serial production and jobs where repeatability is essential. The modular approach also simplifies tool inventory and shortens setup times on CNC milling machines. Secure clamping and precision for reproducible results A 25 mm shank provides a solid connection to standard tool holders and collets, improving stability and lowering radial run-out risk. The cutter has an overall length of 150 mm, offering a balance between reach and rigidity for common milling operations. The insert is secured with an M3x7 Torx screw, tightened using a T8 key, which guarantees secure fixation under intermittent loads and supports consistent seating of the insert. With four flutes, the body delivers steady material removal while maintaining surface finish, helping to extend insert life and reduce rework in downstream processes. Practical workshop integration and dependable supply The tool body is compatible with inserts from established manufacturers such as Korloy, easing procurement and ensuring availability of cutting grades for different materials. As a standardised component within a cutting-tool system, the holder integrates into existing tool libraries without extensive requalification. For buyers looking for reliable sourcing and rapid delivery, Metav Werkzeuge combines a wide inventory with technical support from its Emmerich hub, which acts as a quality filter for European supply. This reduces supplier complexity and supports predictable lead times in production planning. For high-performance indexable milling in production environments, contact Metav Werkzeuge for application advice and ordering support — Metav Werkzeuge: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: R313TM Manufacturer: Teknik Makina Designation: Insert milling cutter for RPMW 0803 indexable inserts SKU: R313TM Numerical data Shank diameter: 25 mm Cutting diameter: 25 mm Overall length: 150 mm Cutting edges: 4 Torx screw: M3x7 Torx key: T8 eCl@ss: 21180806 ETIM: EC011860 Features / Compatibility Fits inserts: RPMW 10T3 Compatible inserts: RPMW 0803 indexable inserts Compatible insert manufacturer: Korloy Secure Torx fixing for repeatable clamp force FAQ Which insert type fits this cutter body? The R313TM insert milling cutter accepts RPMW 0803 style inserts; common compatible sizes include RPMW 10T3, offering flexibility in edge geometry and grades. What is the shank size and how does it affect clamping? The tool has a 25 mm shank, which provides stable clamping in standard collets and reduces run-out for more accurate milling operations. What fastener is used to secure the insert? Inserts are retained with an M3x7 Torx screw; a T8 key is specified for installation and removal to ensure consistent seating. Is the cutter suitable for heavy shoulder milling? The cutter body is intended for light to medium milling tasks where insert change convenience and repeatability matter; machine and process parameters should be matched to the chosen insert grade. What documentation is available for tool integration? Technical specification details such as shank diameter, overall length and compatible inserts are provided for tool selection and setup; refer to the R313TM data points for integration into the tooling system. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter for RPMW 10T3 Indexable Inserts, 2 Cutting Edges - Teknik Makina
Take advantage of a robust shank design and standardised insert compatibility to streamline tooling inventories and shorten changeover times; the combination of a 25 mm shank and acceptance of RPMW 10T3 indexable inserts ensures dependable performance for routine milling tasks—sourced via Metav Werkzeuge for fast European distribution. Shank cutter R317TM – 25 mm shank, for RPMW 10T3 indexable inserts (Teknik Makina) A compact Shank cutter R317TM engineered to accept RPMW 10T3 indexable inserts for efficient face and shoulder milling in general workshop and light industrial applications 25 mm shank diameter Holds RPMW 10T3 indexable inserts 2 cutting edges for stable cutting Secured with M3.5x8.5 Torx screw (T15) Greater compatibility for fewer tool variants This shank cutter is built around a 25 mm shank and a standard insert seat that accepts RPMW 10T3 indexable inserts, enabling workshops to reduce the number of different holders required. By using a commonly available insert size from suppliers such as Korloy, toolrooms benefit from easier stocking and faster replacement cycles. The 120 mm overall length gives a balanced reach for many common milling operations while maintaining rigidity, and the design supports reliable repeatability across batch runs. Secure clamping that speeds up changeovers Insert retention is provided by a M3.5x8.5 Torx screw, tightened with a T15 key, which guarantees firm seating and straightforward exchange of cutting edges. The holder accepts two cutting edges, a geometry that offers both stability and predictable performance during interrupted cuts. This arrangement minimises setup time and reduces the need for intricate clamping fixtures; as a result, process efficiency is improved without sacrificing quality of finish or repeatability on the workpiece. Practical benefits for everyday workshop use Designed by Teknik Makina as a straightforward milling solution, the tool simplifies maintenance and operator training thanks to familiar fasteners and widely available inserts. The reliance on indexable plates allows focused investment in inserts rather than multiple bespoke holders, which is particularly useful for small to medium enterprises looking to balance cost and capability. The robust shank and standardised interface support dependable tool life and ease of service, helping to keep machines productive with minimal downtime. Contact Metav Werkzeuge for tailored technical advice on integrating the Teknik Makina R317TM shank cutter into production and to confirm availability for immediate supply Technical Data SKU: R317TM Type: Shank cutter Brand: Teknik Makina Compatible inserts: RPMW 10T3 Compatible insert manufacturer: Korloy Numbers Shank diameter: 25 mm Diameter: 25 mm Overall length: 120 mm Cutting edges: 2 Special features Torx screw: M3.5x8.5 Torx key: T15 Indexable insert holder Designed for general milling applications FAQ Which insert type fits this cutter? The cutter accepts RPMW 10T3 indexable inserts; Korloy inserts in this format are suitable for the tool. What is the shank diameter and overall length? Shank diameter is 25 mm and overall length is 120 mm, providing a compact yet rigid holder. How are the inserts secured? Inserts are retained with a M3.5x8.5 Torx screw, tightened using a T15 key for secure clamping. How many cutting edges does the holder provide? The holder is configured for 2 cutting edges, offering a stable cutting platform for typical milling tasks. Who manufactures the tool and through whom is it supplied in Europe? The tool is manufactured by Teknik Makina and is supplied in Europe via Metav Werkzeuge for dependable delivery and local support. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter for WNMU 0403 Indexable Inserts, 4 Teeth, 120mm - Teknik Makina
Take advantage of a robust combination of precise insert compatibility and compact design for reliable milling cycles. The tool delivers consistent clamping and easy indexable insert replacement, supporting uninterrupted production — order directly via Metav Werkzeuge or consult the Metav team for specification support. End mill S458TM — Indexable-insert milling cutter, Ø25 mm, 4 flutes (Teknik Cutting Tools) The End mill S458TM is a shank-mounted milling cutter designed for indexable insert milling with WNMU 0403 inserts, suitable for CNC finishing and roughing tasks in industrial workshops Ø25 mm shank for secure machine clamping Compatible with WNMU 0403 indexable inserts Four cutting edges for steady chip evacuation 120 mm overall length for versatile reach Efficient indexable milling with predictable results The S458TM is engineered as an indexable insert milling cutter that combines a compact form with industrial compatibility. The body accepts WNMU 0403 inserts, delivering repeatable cutting geometry without the need for regrinding. This approach reduces downtime: worn edges are replaced in seconds, restoring original cutting conditions. The Ø25 mm shank gives a secure machine fit and improves stability during higher feed operations, while the 4 flutes help maintain consistent chip flow. For operations that require predictable cycle times and straightforward tool handling, the cutter provides a technically simple route to reproducible component quality. Design that supports machining economy and tool life The tool’s configuration emphasises process economy. With a 120 mm overall length and balanced flute count, the cutter lowers vibration and promotes even wear across the insert edges. The use of indexable inserts minimises total tooling cost over time, as insert replacement is faster and less wasteful than regrinding solid tools. The specification includes a Torx fastening system (key T8, screw M2.5 x 5.5) to ensure secure insert clamping and easy maintenance with standard workshop tooling. These details translate directly into fewer tool-change interruptions and improved machine utilisation on batch and single-part production alike. Compatibility and workshop practicality explained Compatibility is clearly indicated: the cutter accepts WNMU 0403 indexable inserts and is ISCAR-compatible, which allows selection from a wide range of insert grades and geometries to match the workpiece material and surface finish requirements. The relatively compact weight (approx. 0.466 kg) and the standard shank diameter simplify handling and storage. For process planners, the ability to choose insert grade independently from the cutter body means rapid adaptation to different materials or cutting strategies without a full tooling change — a pragmatic advantage for mixed-production workshops and subcontractors seeking flexibility. Contact Metav Werkzeuge for tailored technical advice on the S458TM and assistance with sourcing the correct insert grades; technical enquiries can be sent to info@metav-werkzeuge.com or discussed by phone on +49 2822 7131930 — Metav delivers from Emmerich with direct, experienced service. Technical data Article number: S458TM Product name: End mill S458TM Manufacturer: Teknik Cutting Tools Compatible inserts: WNMU 0403 indexable inserts (ISCAR) Core technical data Diameter: 25 mm Shank diameter: 25 mm Overall length: 120 mm Number of cutting edges: 4 Weight: 0.466 kg Torx key: T8 Torx screw: M2.5 x 5.5 Special features Compatible insert manufacturer: ISCAR Insert type: WNMU 0403 SKU: S458TM Brand: Teknik Cutting Tools FAQ What insert type does this cutter accept? The cutter accepts WNMU 0403 indexable inserts; the S458TM body is prepared for this standard insert form. Is the S458TM compatible with ISCAR inserts? Yes, the tool is specified as ISCAR-compatible, enabling the use of ISCAR WNMU 0403 inserts. Which tool secures the insert and what screw is used? Insert clamping uses a Torx key T8 and a Torx screw M2.5 x 5.5, ensuring a secure and serviceable connection. What are the key dimensions for machine setup? Relevant dimensions are 25 mm diameter (shank) and 120 mm overall length; use these values to verify holder compatibility and reach. Can the insert grade be changed for different materials? The S458TM body allows a range of WNMU 0403 insert grades to be fitted, providing flexibility to adapt cutting performance to specific materials and finishes. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shank Milling Cutter For WNMX 0603 Indexable Inserts, 3 Flutes, 60mm Cutting Length - Teknik Makina
Take advantage of a robust combination of stable clamping, extended cutting reach and simple insert compatibility to keep production running reliably; order directly via Metav Werkzeuge or consult our specialists for application advice. S905TM Shaft milling cutter — for WNMX 0603 indexable inserts, Ø25 mm shank The S905TM is a shaft milling cutter optimised for indexable-insert milling with WNMX 0603 plates, intended for versatile machining tasks on CNC and conventional milling centres. Ø25 mm shank for stable clamping Compatible with WNMX 0603 inserts (Korloy) Three cutting edges for efficient material removal 60 mm effective cutting length Stable clamping and extended cutting reach for steady machining The tool features a 25 mm shank, providing a rigid connection to the holder and reducing vibration during heavy cuts. With an effective cutting length of 60 mm and an overall length of 150 mm, the design balances accessibility and rigidity so that longer reaches do not compromise surface quality. This stability translates into consistent cycle times and less rework, which supports efficient production planning. Efficient material removal through three cutting edges and 90° geometry Equipped with three cutting edges and a 90° cutting angle, the cutter delivers predictable chip formation and load distribution across the inserts. The multiple edges reduce cutting forces per flute, enabling steady feed rates and improved tool life under comparable conditions. The indexable-insert concept allows rapid exchange of worn cutting edges, which shortens downtime and keeps machining throughput high. Simple maintenance and proven insert compatibility The milling head uses WNMX 0603 indexable inserts and secures them with a Torx M2.5x5.5 screw tightened with a T8 key, ensuring repeatable clamping torque and fast service intervals. Compatibility with Korloy inserts provides access to a broad range of grades for steel, cast iron and non-ferrous applications (select inserts according to the workpiece and machining strategy). The modular approach reduces tooling inventory and supports predictable operating costs. For reliable supply and tailored technical advice from Metav Werkzeuge regarding the Teknik Makina S905TM shaft milling cutter, contact our Emmerich team to discuss suitable inserts and holder options Technical Data Article number: S905TM Brand: Teknik Makina SKU: S905TM ECLASS: 21180806 ETIM: EC011860 Numbers / Core technical data Shank diameter: 25 mm Effective cutting length: 60 mm Overall length: 150 mm Number of cutting edges: 3 Cutting angle: 90° Weight: 0.578 kg Special features / Versions Compatible inserts: WNMX 0603 Suitable insert manufacturer: Korloy Torx screw: M2.5x5.5 Torx key size: T8 FAQ What insert type does this cutter use? The cutter accepts WNMX 0603 indexable inserts, which are the specified grade for this shaft milling cutter. Can the tool be used with Korloy inserts? Yes, this cutter is compatible with Korloy WNMX 0603 inserts and benefits from the range of grades they offer. What shank diameter and cutting reach does it provide? The tool has a 25 mm shank and an effective cutting length of 60 mm, with a total length of 150 mm. How are the inserts secured? Inserts are clamped with a Torx M2.5x5.5 screw; the appropriate key is T8 for reliable fastening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Shell End Mill For APKT 1604 Indexable Inserts, 2 Flute, 90° Cutting Angle, 70mm Cutting Length - Teknik Makina
Benefit from a rigid 25 mm shank, a 90° cutting angle and quick insert changes to maintain steady production with minimal downtime; Order the S432TM shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed S432TM shank milling cutter — 25 mm shank, for APKT 1604 indexable inserts | Teknik Makina The S432TM is a shank milling cutter engineered for APKT 1604 indexable inserts, providing a compact 25 mm diameter and a 90° cutting angle for reliable shoulder and face machining in industrial milling applications 25 mm shank diameter Compatible with APKT 1604 inserts 90° cutting angle for square shoulders Includes M4x10 Torx screw T15 Greater rigidity for consistent machining results With a 25 mm shank and a total length of 250 mm, this shank milling cutter delivers enhanced rigidity that reduces chatter and improves surface finish. The robust design supports stable cutting conditions over longer runs, which translates into fewer rejects and a more predictable production flow. The single-line geometry with 2 cutting edges balances material removal and tool life, enabling efficient use of the insert system while maintaining dimensional accuracy on repetitive shoulder cuts. Fast, cost-effective indexable system to cut downtime Designed for APKT 1604 indexable inserts, the tool reduces maintenance time through quick insert replacements instead of complete tool swaps. The replaceable-insert concept is economical for batch production: worn edges are replaced swiftly using the supplied M4x10 Torx screw (tightened with a T15 key) without special fixtures. Compatibility with Korloy inserts broadens procurement options, supporting uninterrupted operation and simpler stocking of consumables for the workshop. Practical dimensions and handling for workshop integration The cutter features a 70 mm cutting length, which provides sufficient engagement for many face and shoulder milling operations while keeping the effective overhang modest. At approximately 0.939 kg, the tool is easy to handle during tool changes and balances well in most toolholders. The 90° cutting angle ensures reliable right-angle geometries, reducing the need for subsequent finishing passes and helping maintain throughput without sacrificing profile accuracy. For precise specification and supply of the S432TM shank milling cutter from Teknik Makina, contact Metav Werkzeuge to confirm compatibility with current toolholder systems and to secure reliable delivery from Emmerich Technical data Article number: S432TM Manufacturer: Teknik Makina For indexable inserts: APKT 1604 Compatible insert supplier: Korloy Torx screw: M4x10 Torx key size: T15 Core data Shank diameter: 25 mm Cutting diameter: 25 mm Cutting length: 70 mm Overall length: 250 mm Number of cutting edges: 2 Cutting angle: 90° Weight: 0.939 kg Special features Indexable insert system (APKT 1604) Supplied fastening screw M4x10 (Torx T15) Two-flute configuration for balanced cutting Compact overall length for reduced overhang Compatible with Korloy inserts FAQ What inserts fit this shank milling cutter? The S432TM is designed for APKT 1604 indexable inserts, and it is also compatible with inserts from Korloy as noted in the technical data. How is the insert secured to the cutter? Inserts are fastened with an M4x10 Torx screw, which is tightened using a T15 key; this arrangement allows quick and secure insert changes for continued productivity. What machining geometry does the tool offer? The cutter provides a 90° cutting angle, suitable for square shoulder and face milling where right-angle profiles and consistent step geometry are required. What are the key dimensions to consider for toolholder selection? Important dimensions include the 25 mm shank diameter, 70 mm cutting length, and 250 mm overall length; these values ensure the correct fit and acceptable overhang for the chosen toolholder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shell End Mill For APKT 1604 Indexable Inserts, 2 Flutes 55mm Cutting Length, 90° Cutting Angle - Teknik Makina
Take advantage of a rigid 25 mm shank and compatibility with APKT 1604 indexable inserts for stable, repeatable cuts; the secure M4x10 Torx fastening and compact 150 mm overall length reduce setup time and vibration, supporting a smooth milling process. Order or request guidance via Metav Werkzeuge for application advice or procurement. Shank milling cutter S266TM – 25 mm shank, for APKT 1604 indexable inserts (Teknik Cutting Tools) The Shank milling cutter S266TM is a purpose-built insert cutter body engineered for face and slot milling with APKT 1604 indexable inserts, offering a compact overall length and secure Torx clamping for consistent tool performance 25 mm shank diameter for rigidity 2 cutting edges for efficient material removal Compatible with APKT 1604 indexable inserts Secured with M4x10 Torx screw (T15) High-precision insert compatibility for predictable results The cutter body is designed around the widely used APKT 1604 insert format and matched to major suppliers such as Korloy, which simplifies inventory and insert selection. The combination of standard insert geometry and a firm clamping concept—specified as an M4x10 Torx screw with a T15 key—reduces micro-movement during operation, improving surface finish and repeatability. For manufacturing planners this translates into fewer reworks and more predictable cycle times, since the modular insert system enables quick replacement without readjusting the toolholder or machine offsets. Robust shank and geometry for stable cutting performance With a 25 mm shank diameter and a total length of 150 mm, the tool provides a balance between accessibility and stiffness; the cutting length of 55 mm and 2 cutting edges at a 90° cutting angle enable efficient face milling and light slotting. The solid ergonomics lower vibration and allow higher feed per tooth within recommended limits, increasing throughput while maintaining tolerances. Calculations for fixture and spindle load become straightforward thanks to the clear dimensional data and the modest tool mass (0.544 kg), which helps in process planning and tool-change cycle optimisation on both small jobbing machines and larger production centres. Practical integration into workshop workflows The cutter body has been specified with common industry standards to ease adoption in mixed-workshop environments. Its compatibility with APKT 1604 inserts and recognition of Korloy as a fitting insert supplier reduce procurement complexity and support fast replacement during shift work. The compact design and standardised Torx fastening mean that the tool can be swapped and secured quickly, lowering downtime and supporting lean production routines. For operations managers, the result is a straightforward, durable insert milling solution that complements existing toolsets and enables consistent component quality across runs. For advice on applications, stock availability or to specify the S266TM shank milling cutter for production, contact Metav Werkzeuge in Emmerich for personalised guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: S266TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Facts Shank diameter: 25 mm Cutting length (shank): 55 mm Overall length: 150 mm Number of cutting edges: 2 Cutting angle: 90° Weight: 0.544 kg Special features For indexable inserts: APKT 1604 Compatible insert manufacturer: Korloy Torx screw: M4x10 Torx key size: T15 SKU: S266TM FAQ What insert type does this cutter accept? The cutter accepts APKT 1604 indexable inserts; the S266TM is engineered around that insert geometry to ensure correct seating and reliable cutting behaviour. Is a specific insert supplier required? No single supplier is required, but the tool is marked as compatible with Korloy APKT 1604 inserts; equivalent inserts from other manufacturers with the same designation will fit. What clamping method secures the insert? Insert clamping is achieved via a Torx screw specified as M4x10, tightened with a T15 key to ensure secure fixation and minimise movement during cutting. Can the tool be used for both face milling and slotting? Yes, the cutter’s 90° cutting angle and 55 mm cutting length make it suitable for face milling and light slotting operations, offering versatility for various workshop tasks. How does the shank diameter affect performance? The 25 mm shank increases rigidity compared with smaller diameters, reducing deflection and vibration for improved surface finish and repeatability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shell Mill For APMT 11T3 Indexable Inserts 3 Cutting Edges, 90° Cut Length 35mm - Teknik Makina
Take advantage of the combination of robust clamping, precise compatibility and compact design to keep machining cycles predictable and changeover times low; the secure Torx fastening and standard indexable format make integration into existing toolholders straightforward. Order the S236TM via Metav Werkzeuge or contact our technical consultants for application advice. S236TM – Shank cutter, 25 mm diameter for APMT 11T3 indexable inserts (Teknik Cutting Tools) The S236TM is a shank cutter designed for use with APMT 11T3 indexable inserts, offering a compact overall length and a secure Torx clamping system for repeatable insert changes in general milling and shoulder operations. 25 mm shank diameter Compatible with APMT 11T3 inserts Three cutting edges for stable cutting 90° cutting angle for shoulder milling Consistent clamping and compatibility for stable production The shank construction with a 25 mm shank and an overall length of 115 mm delivers a balance between stiffness and reach, making the tool suited to short-to-medium overhang operations. Designed around the common APMT 11T3 indexable format, the cutter permits rapid insert rotation or replacement without the need for regrinding; this lowers machine downtime and maintains process repeatability. The standardised insert interface ensures compatibility with established insert suppliers such as Korloy, enabling easy sourcing of proven geometries and grades for a wide range of steels and non-ferrous materials. Efficient cutting geometry that reduces vibrations and finish time Equipped with 3 cutting edges, the tool distributes cutting forces to reduce chatter and improve surface finish on stepped faces and shoulders. The 90° cutting angle produces true perpendicular faces, which simplifies fixture set-up and downstream assembly for machined components. A 35 mm cutting length provides adequate engagement for many common pocket and face milling operations while keeping unsupported length low; the compact cutting zone helps to preserve insert life and reduces the likelihood of deflection during interrupted cuts. Practical fastening and handling for quick insert changes Insert retention is handled by an M2.5×5.5 Torx screw paired with a T8 key, offering reliable clamping torque with a familiar service tool. This fastening arrangement supports quick, repeatable insert changes and secure retention under typical spindle speeds and feeds for indexable milling heads. For workshops new to indexable tooling, the use of replaceable inserts means maintenance becomes a matter of stock and rotation rather than regrinding, simplifying toolroom logistics and supporting predictable throughput. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Cutting Tools S236TM into production; technical consultants at Metav Werkzeuge can advise on insert grades, suitable feeds and speeds, and supply options — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S236TM Manufacturer: Teknik Makina Facts Shank diameter: 25 mm Cutting length: 35 mm Overall length: 115 mm Number of cutting edges: 3 Cutting angle: 90° Weight: 0.423 kg Special features Compatible with APMT 11T3 indexable inserts Torx screw M2.5x5.5 for insert clamping Torx key size T8 required Suitable insert manufacturer: Korloy FAQ What inserts does this cutter use? The S236TM takes APMT 11T3 indexable inserts; the cutter is supplied for that insert size and is compatible with standard APMT geometries from suppliers such as Korloy. How is the insert secured in the cutter? Insert retention is by an M2.5x5.5 Torx screw tightened with a T8 key, offering secure clamping and straightforward removal for index or replacement. Is the cutter suitable for shoulder milling? Yes, the 90° cutting angle and stiff 25 mm shank make the tool appropriate for shoulder and face milling where perpendicular walls are required. Can the S236TM be used with any toolholder? The tool is a standard shank cutter; compatibility with a specific toolholder depends on the holder’s shank clamping capacity and runout tolerance — the shank diameter is 25 mm. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shell Mill for R390-1704 Indexable Inserts, 2 Flutes 90° Cutting Angle, 55mm Cutting Length - Teknik Makina
Take advantage of the combination of secure clamping, indexable-insert efficiency and easy maintenance for uninterrupted milling operations. Order the tool directly via Metav Werkzeuge or consult our technical advisors for retrofit and application advice. S520TM Shank Milling Cutter – 25 mm shank, for R390‑1704 indexable inserts (Teknik Makina) The S520TM shank milling cutter is a shank-mounted milling body designed for use with R390‑1704 indexable inserts, providing a compact, serviceable solution for workshops and production cells where fast insert changes and consistent results are essential Compatible with R390‑1704 Sandvik inserts 25 mm shank diameter for robust clamping Two cutting edges with 90° cutting angle Torx screw M3.5x8.5, Torx key T15 Stability and machining accuracy for repeatable results A robust 25 mm shank and a balanced overall construction deliver improved stability during milling, which reduces chatter and supports consistent surface finish. With an overall length of 150 mm and a mass of 0.536 kg, the tool body is designed to keep rotational inertia moderate while providing sufficient reach for typical milling operations. These design choices translate into predictable cutting behaviour, reduced rework and longer life for both the cutting body and the inserts. Efficient indexable-insert system that lowers operating costs The holder is configured specifically for R390‑1704 indexable inserts and is compatible with Sandvik plate geometries, enabling rapid re-indexing and minimal downtime. The cutter provides two cutting edges and a 90° cutting angle, delivering a reliable cutting geometry for slotting and peripheral milling tasks. A 55 mm cutting length allows a useful engagement range while keeping the insert support rigid, which benefits tool life and cost per part through straightforward insert replacement rather than full-bodied regrinding. Fast insert changes and secure fastening to reduce downtime Insert clamping and replacement are simplified by the use of a Torx M3.5x8.5 fastening screw and a T15 key interface, which standardises the maintenance procedure and speeds up changeovers. This clear mechanical specification ensures service technicians and operators can perform insert changes quickly and repeatably, lowering machine idle time and improving net productive hours on the shop floor. Practical advantages for procurement and workshop logistics Standardisation on a holder that accepts widely used inserts reduces the number of special spare parts required and simplifies stock management without compromising process capability. The S520TM’s compatibility with established insert formats means fewer unique tool bodies to order and an easier spare-parts strategy. For purchasing and production planning, this translates into a leaner tool inventory and faster response to varying production demands. For retrofit, application support or to order the S520TM shank milling cutter via Metav Werkzeuge, contact our specialists at Metav Werkzeuge GmbH; Parkring 45; Emmerich — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: S520TM Manufacturer: Teknik Makina Designation: Shank milling cutter for R390‑1704 indexable inserts Article type (EN): Insert milling cutter body For indexable inserts: R390‑1704 Compatible inserts manufacturer: Sandvik Fastening screw: M3.5x8.5 Torx key size: T15 Facts Shank diameter: 25 mm Cutting length (shank): 55 mm Overall length: 150 mm Diameter: 25 mm Number of cutting edges: 2 Cutting angle: 90° Weight: 0.536 kg eCl@ss: 21180806 ETIM: EC011860 Special features For R390‑1704 indexable inserts Compatible with Sandvik insert geometries Torx M3.5x8.5 fastening Torx key requirement: T15 FAQ Which insert type fits this milling cutter? The S520TM accepts R390‑1704 indexable inserts; the cutter body is designed for the corresponding Sandvik plate geometry and clamping method. How many cutting edges does the tool provide and what is the cutting angle? The holder is set up with two cutting edges and a 90° cutting angle, offering a stable engagement profile for slotting and peripheral milling. What are the shank diameter and overall length of the cutter? The tool has a 25 mm shank diameter and an overall length of 150 mm, which balances reach and rigidity for typical workshop milling tasks. What fastening hardware is required for insert clamping? Insert clamping uses a Torx M3.5x8.5 screw and requires a T15 Torx key for secure and repeatable assembly; the specification is listed under SKU S520TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shell Mill For VCGT 1604 Indexable Inserts, 2 Flutes, 60mm Cutting Length - Teknik Makina
Take advantage of a robust combination of stable clamping, quick insert changes and proven compatibility with VCGT 1604 indexable inserts to keep machining cycles efficient and predictable. Order the tool via Metav Werkzeuge or contact the consultants for application advice and delivery from Emmerich. S718TM — Shank milling cutter, 25 mm shank, for VCGT 1604 indexable inserts (Teknik Makina) The S718TM is a shank milling cutter engineered for use with VCGT 1604 indexable inserts, offering a compact overall length and a long effective cutting portion for stable slotting and face milling on production machinery. 25 mm shank diameter for rigid clamping 60 mm effective cutting length Compatible with VCGT 1604 indexable inserts Supplied with M4x10 torx fixing screw High stability and material removal performance for continuous workflows The tool's 25 mm shank and precisely machined body provide rigid clamping, reducing vibration and improving tool life when paired with appropriately rated holders. The combination of a 60 mm cutting length and a compact overall length supports longer engagement in deep passes while maintaining balance; this lowers the risk of chatter and improves surface finish. Compatibility with VCGT 1604 indexable inserts makes the system cost-effective: worn cutting edges are replaced quickly, reducing spindle downtime and simplifying inventory management for routine servicing. Fast insert changes and straightforward assembly to reduce downtime Insert retention uses a M4x10 torx fixing screw tightened with a T15 key, enabling fast, repeatable insert changes without specialised fixtures. The retained screw specification and conventional torque interface allow maintenance teams to standardise procedures and reduce tool change time. At 0.73 kg the tool offers manageable mass for handling and mounting, while the balanced construction supports predictable runout and repeatability across shifts—advantages that translate directly into higher machine utilisation and reduced per-part processing time. Application fit and operational benefits in production environments With two cutting edges and its defined geometry, the cutter is suitable for medium-duty milling tasks where efficiency and repeatability matter. The insert-based design separates the cutting material from the tool body, offering economic advantages when machining abrasive or variable alloys: only the insert requires replacement. For engineering workshops, CNC job shops and in-house production lines the construct supports both single-pass and multi-pass strategies, enabling clear process planning and cost control while retaining the flexibility to adapt cutting data as materials or feed requirements change. Reliability, handling and inventory advantages The indexable system simplifies stock keeping and reduces capital tied up in spare holders; shops can hold a small number of bodies and a larger pool of inserts to cover varied jobs. The shank configuration and standard fixing screw help ensure consistent assembly practice across operators, improving safety and repeatability. Technical documentation and file assets associated with the tool (referenced in the product files) support setup routines and spare-part planning, helping to maintain steady throughput on production lines. For tailored advice on integrating the S718TM into current toolsets or to secure rapid delivery from Emmerich, contact Metav Werkzeuge — call +49 2822 7131930 or email info@metav-werkzeuge.com for application guidance and stock information Technical data Article number: S718TM Manufacturer: Teknik Makina Designation: Shank milling cutter for VCGT 1604 indexable inserts Facts Diameter: 25 mm Shank diameter: 25 mm Cutting length: 60 mm Overall length: 200 mm Cutting edges: 2 Weight: 0.73 kg Torx screw: M4x10 Torx key: T15 Special features Compatible with VCGT 1604 indexable inserts File assets available (IDs: 62de7e4fbd24461b3d5f7a29, 62de7ee50f56dbb4de4dbf58) Indexable-insert system for economical edge replacement Compact overall length for reduced overhang FAQ What inserts does the tool accept? The S718TM accepts VCGT 1604 indexable inserts, allowing rapid edge changes and flexible selection of grades for different materials. How is the insert secured to the cutter? Insert retention is by a M4x10 torx screw tightened with a T15 key; this standardised fixing helps ensure repeatable clamping and straightforward maintenance. Is this cutter suitable for deep shoulder milling? The tool's 60 mm effective cutting length and 25 mm shank give a good balance between reach and rigidity, making it appropriate for many shoulder and slotting operations in medium-duty applications. What are the handling and mounting considerations? Weighing 0.73 kg, the cutter is easy to handle during setup; mounting should use a properly rated holder to exploit the tool's rigid clamping characteristics and to minimise runout. Can the S718TM be used across different machine types? Yes, the shank configuration and conventional fixing method make the S718TM adaptable to a range of CNC milling setups, provided appropriate holders and spindle interfaces are used. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm Shell Mill for XOMX 1204 Indexable Inserts With Internal Coolant, 120mm Length - Teknik Makina
Take advantage of the internal coolant, 25 mm shank and compatibility with XOMX 1204 indexable inserts to achieve stable, economical milling in serial or job-shop production; order the S642-1TM through Metav Werkzeuge or consult our specialists for application matching. Shank Milling Cutter S642-1TM by Teknik Makina — 25 mm shank, internal coolant Shank Milling Cutter S642-1TM engineered for indexable-insert milling on CNC machines, offering internal coolant and a compact 120 mm overall length for precision machining applications 25 mm shank diameter for stable clamping Internal coolant for efficient chip evacuation Compatible with SECO XOMX 1204 indexable inserts Three cutting edges for balanced milling performance High-stability design for consistent metal removal The cutter’s 25 mm shank and balanced three cutting edges deliver high radial stability and reduced vibration during interrupted or continuous cuts. Such mechanical steadiness translates into more consistent surface finish and tighter tolerances, which is essential for batch production and precision components. The combination of a rigid shank and optimised cutter geometry reduces tool deflection, supporting longer tool life and predictable machining results in demanding milling tasks. Internal coolant improves performance and tool life Equipped with internal coolant, the tool directs cutting fluid precisely to the cutting zone, promoting effective chip control and heat dissipation. This reduces edge wear and lowers the risk of built-up edge formation, which helps maintain dimensional stability over longer tool cycles. For shops aiming to reduce rework and maintain throughput, the coolant-fed design offers a measurable improvement in process reliability without requiring changes to existing coolant supply systems. Indexable-insert concept for fast changeovers and cost efficiency Designed for XOMX 1204 indexable inserts and compatible with SECO insert systems, the cutter enables rapid insert replacement with a T10 Torx key and M3.5x8.5 fastening screw, keeping downtime to a minimum. The insert-based approach allows selective replacement of worn cutting edges rather than whole tools, lowering tooling costs and simplifying inventory management. For operations that balance productivity with budget control, this modular system supports efficient life-cycle economics. Precise dimensions for seamless workshop integration With an overall length of 120 mm, a cutting length of 45 mm and a nominal weight of 0.443 kg, the S642-1TM offers compact geometry that fits conventional tool holders while keeping the centre of mass close to the spindle for improved control. These measured dimensions aid in programming and balancing on CNC equipment, ensuring predictable tool paths and repeatable outcomes. Delivered as a ready-to-fit shank milling cutter, the design suits a wide range of milling setups where both performance and fixture compatibility matter. Discuss the Teknik Cutting Tools S642-1TM with Metav Werkzeuge for tailored tool selection and reliable supply from Emmerich; contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S642-1TM Product type: Shank milling cutter Brand: Teknik Makina Core specifications Shank diameter: 25 mm Overall length: 120 mm Cutting length (shank): 45 mm Number of cutting edges: 3 Weight: 0.443 kg Torx key: T10 Torx screw: M3.5x8.5 Internal coolant: yes Special features Compatible with XOMX 1204 indexable inserts Suitable for SECO insert systems Indexable-insert concept for quick changeovers FAQ What insert type does the cutter accept? The cutter accepts XOMX 1204 indexable inserts; it is supplied to work with established SECO-style inserts for economical edge replacement. Is the tool coolant-fed? Yes, the S642-1TM features internal coolant to improve chip evacuation and reduce cutting edge wear during prolonged milling operations. What are the key dimensions for machine setup? Important dimensions are a 25 mm shank diameter, 120 mm overall length and 45 mm cutting length, facilitating integration into standard tool holders. Which fastening tool is required for insert changes? Insert clamping uses a T10 Torx key and an M3.5x8.5 screw for secure, repeatable insert fixing. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm Solid Carbide End Mill For 4NKT06 Indexable Inserts, 4 Flutes, 30mm Cutting Length - Teknik Makina
Take advantage of a rigid, replaceable‑insert milling solution that combines a Ø25 mm shank with four cutting edges and a 30 mm effective cutting length for stable, repeatable machining; order directly via Metav Werkzeuge or consult the team for application guidance. S475TM — Indexable Insert Shank Cutter by Teknik Cutting Tools, Ø25 mm, 4‑edge The S475TM is a robust shank cutter designed for indexable inserts, engineered for medium‑duty milling and slotting tasks where rapid insert changes and consistent surface quality are required. Precision Ø25 mm shank for stable clamping Compatible with Taegutec 4NKT06 indexable inserts Four cutting edges for balanced material removal Torx clamping M3x6,5 with T8 key for secure fixing Stable machining through a rigid shank and balanced geometry The S475TM was developed to give consistent milling results in production and workshop environments. Its Ø25 mm shank provides high radial stiffness in standard tool holders, which reduces vibration and improves surface finish when milling. With four cutting edges, the cutter delivers a balanced cutting action that spreads the load and lowers peak forces, supporting longer tool life of the indexable system. The combination of cutting length 30 mm and total length 120 mm offers a practical reach for many face and slot milling operations while keeping deflection to a minimum. These attributes translate into fewer reworks and more predictable cycle times on the shop floor. Economical, fast‑changing indexable system that reduces downtime Designed around indexable inserts, the tool accepts the 4NKT06 family (compatible with Taegutec), allowing simple replacement of worn cutting edges without regrinding. Insert‑based tooling is a cost‑efficient choice for workshops that seek to reduce tooling stock and maintenance time: one reversible insert change restores original cutting geometry in seconds. The secure fixation by Torx M3x6,5 clamping screw and T8 key ensures repeatable seating of the insert, helping to maintain cutting accuracy and reduce the need for frequent tool checks. This approach supports continuous production with minimal tooling overhead. Simple integration and low‑effort maintenance for workshop use The cutter’s dimensions and standard connection make it straightforward to fit into common milling holders and adapters. With a weight of 0.474 kg, handling and tool changes remain easy for operators, while the Ø25 mm shank conforms to many toolholding systems for immediate integration. Routine maintenance is limited to insert inspection and replacement plus periodic checking of the Torx clamping screw torque; this keeps maintenance cycles short and predictable. The modular concept enables targeted inventory management — keep a few insert grades and one shank cutter to cover a wide range of tasks. Suitable operations and practical recommendations for selection This shank cutter is intended for general‑purpose milling tasks where the 4‑edge insert arrangement provides balanced material removal; typical uses include shoulder milling, slotting and light face milling where replaceable inserts offer the best economy. Selection of the correct insert grade and chipbreaker for the workpiece material is decisive for performance; if specific material data are required or for heavy‑duty applications, consult the technical advisers to match insert geometry and grade to the process. For controlled, repeatable machining with quick insert swaps, the S475TM offers a pragmatic balance of rigidity, accessibility and serviceability. For procurement and application support on the Teknik Cutting Tools S475TM, contact Metav Werkzeuge for tailored advice and local availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — Metav’s specialists assist with selection and integration into production workflows Technical data Article number: S475TM Brand: Teknik Makina Type: Shank cutter for 4NKT 0603 indexable inserts ECLASS: 21180806 ETIM: EC011860 Core dimensions Shank diameter: 25 mm Cutting length: 30 mm Total length: 120 mm Diameter: 25 mm Cutting edges: 4 Weight: 0.474 kg Features / Compatibility For 4NKT06 indexable inserts Compatible insert manufacturer: Taegutec Torx screw: M3x6,5 Torx key size: T8 SKU: S475TM FAQ Which inserts fit this shank cutter? The cutter accepts 4NKT06 indexable inserts; compatibility with Taegutec 4NKT06 is specified for straightforward sourcing and interchange. How is the insert secured in the cutter? Insert fixation is achieved with a Torx clamping screw M3x6,5 tightened using a T8 key to ensure repeatable seating and secure clamping. What are the main advantages of using this indexable shank tool? The S475TM offers rapid insert replacement, reduced tooling costs through replaceable edges, and a Ø25 mm shank that improves rigidity for consistent surface quality. Can this cutter be used in existing toolholders? Yes — the Ø25 mm shank diameter is compatible with standard holders designed for that size, enabling quick integration into many setups. How long is the effective cutting length and what reach does the tool offer? The tool provides a cutting length of 30 mm and a total length of 120 mm, giving adequate reach for common face and slot milling operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
High-performance shank cutters and ball nose cutters for efficient milling
Insert shank cutters and ball nose cutters combine flexibility and productivity for a wide range of milling tasks. The category covers steel-bodied shank cutters fitted with indexable inserts for economical roughing, face milling, cornering and slotting, as well as ball nose cutters for contouring and 3D finishing.
How these tools work and where they belong
Shank cutters with indexable inserts use a carrier body made from hardened steel; the cutting edges are provided by removable inserts rather than a solid tool blank. Where tools do not have internal coolant, process heat and chips are managed via external coolant nozzles or compressed air, which is sufficient for open, surface-level and easily accessible milling on standard materials. Shank cutters with internal coolant feature fine internal channels that deliver coolant or blasting air directly to each cutting edge under pressure. This targeted supply is essential for deep pockets, cavities, full slotting and machining of heat-resistant or difficult-to-machine materials, because it prevents chip re-cutting, protects cutting edges from thermal overload and enables higher feed rates and improved surface quality.
Cut cycle times and reduce tooling costs
- Replaceable indexable inserts reduce consumable costs and shorten tool change time.
- Targeted internal coolant improves chip evacuation and extends insert life.
- Robust steel carrier bodies enable heavy-duty roughing without frequent tool replacement.
- Suitable for roughing, planing, corner milling and slot milling as well as precision 3D profiling with ball nose cutters.
A practical choice for purchasing and stocking tools
Metav brings a pragmatic purchasing advantage: a broad range of milling solutions is available from a single European quality hub. Metav’s focus on democratising precision means workshops benefit from a wide assortment, consistent quality control from Emmerich and steady supply — supported by decades of expertise and over 48,000 satisfied customers. Choose Metav for a centralised sourcing strategy that reduces supplier complexity while keeping access to both insert milling cutters (also referred to as insert milling cutters or indexable end mills) and ball nose cutters (also known as ball nose end mills or radius cutters) straightforward.
Quick summary
Insert shank cutters and ball nose cutters deliver flexible, cost-effective milling: replaceable inserts lower running costs, and internal coolant options enable higher performance and longer tool life where chip control is critical.
FAQ
When should I choose a shank cutter with indexable inserts rather than a solid carbide end mill?
Choose shank cutters with indexable inserts for economical roughing and high-stock-removal tasks where replacing inserts is preferable to replacing an entire tool; they are especially effective for face milling, cornering and slotting operations.
Does internal coolant make a measurable difference for ball nose cutters?
Yes. Internal coolant directed to each cutting edge reduces chip re-cutting and thermal stress, which improves surface finish and increases insert life when machining deep pockets, cavities or heat-resistant materials.
Can shank cutters without internal coolant be used for general workshop milling?
Absolutely. Tools without internal coolant rely on external coolant nozzles or compressed air and are well suited to open, superficial and easily accessible milling on standard materials.
What milling operations are shank cutters for indexable inserts typically used for?
Shank cutters with indexable inserts excel at economical roughing, planfräsen (face milling), corner milling and slot milling; ball nose cutters are the preferred choice for 3D profiling and finishing operations.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com