Efficient shaft cutters and ball nose cutters for versatile milling
Shaft cutters and ball nose cutters serve as robust rotating tools for roughing, face milling, corner milling and slotting, offering economical replacement of indexable inserts rather than whole solid tools. Available in versions with internal coolant to feed lubricant directly to each cutting edge or without internal coolant relying on external nozzles, these cutters ensure effective chip evacuation and thermal control suited to standard materials or deep pocket and cavity work. By preventing chip re-cutting and protecting cutting edges, they deliver higher feed rates, improved surface finish and extended tool life in demanding metalworking applications.
25mm End Mill For ADKT 1505 Indexable Inserts, 2 Flutes, 45mm Cutting Length, 120mm Overall - Teknik Makina
Benefit from a robust combination of a 25 mm shank, 45 mm cutting length and ADKT 1505 insert compatibility for consistent, low‑vibration milling; order via Metav Werkzeuge or consult their specialists for application guidance. Shank milling cutter S304TM — for ADKT 1505 indexable inserts, 25 mm shank (Teknik Cutting Tools) A versatile shank milling cutter S304TM intended for indexable‑insert face and slot milling where quick insert changes and secure clamping are required. Compatible with ADKT 1505 indexable inserts 25 mm shank diameter for stable clamping Two cutting edges for balanced milling Supplied with M4x10 Torx clamping screw Maximum flexibility through proven insert compatibility The S304TM is built around the widely used ADKT 1505 insert format, which allows shops to adopt a familiar insert geometry and maintain stock efficiency. With the indexable inserts interface, the tool facilitates rapid replacement of cutting edges without the need to regrind tools, reducing downtime and supporting predictable process planning. The association with established insert types also simplifies procurement and keeps tooling costs manageable over many production cycles. Dimensional stability that reduces vibration and runout Engineered with a 25 mm shank and an overall length of 120 mm, the tool provides a stable connection to standard toolholders while maintaining accessibility for deeper machining tasks. The 45 mm cutting length and two cutting edges combine to deliver a compact cutting zone and a symmetric cutting load, which helps to reduce vibration during interrupted cuts. These dimensional choices favour consistent surface finish and longer insert life when used within recommended speeds and feeds. Fast changes and secure clamping to keep production moving Clamping is executed with a M4x10 Torx screw and requires a T15 key, ensuring repeatable and secure insert retention for each replacement. The device’s modest mass (0.434 kg) minimises additional spindle inertia while preserving rigidity, which is beneficial in high‑repetition milling tasks. For commissioning or process integration, technical advice is available from Metav Werkzeuge to confirm holder compatibility and to recommend suitable cutting parameters for the specific ADKT 1505 grade in use. For tailored technical advice or immediate availability of the Teknik Cutting Tools S304TM, contact Metav Werkzeuge by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to ensure the tool meets production requirements Technical data Article number: S304TM Manufacturer: Teknik Makina Product: Shank milling cutter for ADKT 1505 indexable inserts Facts Shank diameter: 25 mm Cutting length: 45 mm Overall length: 120 mm Diameter: 25 mm Cutting edges: 2 Weight: 0.434 kg Special features Compatible with ADKT 1505 inserts Fits ISCAR insert geometry Torx clamping screw M4x10 Torx key size T15 Brand: Teknik Cutting Tools FAQ Which insert type does this cutter accept? The cutter accepts ADKT 1505 indexable inserts; the geometry is compatible with the ADKT 1505 insert format used by ISCAR. What are the key dimensions to check for holder compatibility? Check the 25 mm shank diameter and 120 mm overall length against the toolholder; the cutting area extends 45 mm from the shoulder. How many cutting edges does the tool have and what is the benefit? The tool has two cutting edges, which provide a balanced cutting action for stable milling and consistent surface finish. Which clamping components are required for insert fixation? Insert fixation uses an M4x10 Torx screw tightened with a T15 key for repeatable, secure clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for ADKT 1706 Indexable Inserts With Internal Coolant, 115mm Overall Length - Teknik Makina
Benefit from the combination of 25 mm shank rigidity, internal coolant and compatibility with ADKT 1706 indexable inserts for stable, repeatable milling. Order or request technical advice directly via Metav Werkzeuge to integrate this tool into an efficient production setup. S063TM Shank milling cutter for ADKT 1706 indexable inserts — 25 mm shank, internal coolant (Teknik Makina) The S063TM shank milling cutter is designed for milling applications that use ADKT 1706 indexable inserts, offering a compact overall length and through-tool coolant for consistent chip control. 25 mm shank diameter for stable clamping Internal coolant for improved chip evacuation Compatible with ADKT 1706 indexable inserts 35 mm cutting length for versatile engagement Increased stiffness for consistent part quality A robust 25 mm shank increases the toolholder interface stiffness and helps to reduce deflection during lateral cuts. The result is improved precision and repeatable tolerances across batch production. Using a stiffer shank reduces vibration and contributes directly to surface finish consistency, making the tool a rational choice where geometrical accuracy and process stability are priorities. Through-tool cooling to extend tool life and manage chips The integrated internal coolant supplies cooling fluid close to the cutting edge, enhancing heat dissipation and promoting efficient chip evacuation. Cooler cutting zones reduce wear at the insert edge and therefore extend service intervals for the insert system. For operations where thermal build-up shortens tool life, this configuration supports longer stable cutting times and fewer unscheduled tool changes. Standardised insert system for inventory and cost efficiency Compatibility with ADKT 1706 indexable inserts and recognised insert manufacturers such as Korloy enables the use of standard inserts across multiple tool holders. This reduces the number of special items in stock, simplifies reordering and allows flexible selection of grades and geometries for different materials. The modular approach supports a cost-effective tooling strategy without compromising machining performance. Secure fastening and service-friendly maintenance Insert clamping is performed with a T15 Torx key and M4x10 screw, ensuring a reliable, repeatable connection between insert and cutter body. With two cutting edges and a 35 mm cutting length, the cutter offers a straightforward balance between material engagement and accessibility for insert changes. Fast, tool-room-friendly maintenance reduces downtime and keeps machines productive. For milling tasks that demand rigidity and controlled cooling, contact Metav Werkzeuge for tailored advice and fast supply — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the S063TM and integration options. Technical data SKU: S063TM Product type: Shank milling cutter Designation: Schaftfräser Description: for ADKT 1706 indexable inserts Label: 25mm Schaftfräser ADKT 1706 L115mm mit Innenkühlung Facts Diameter: 25 mm Overall length: 115 mm Weight: 0.61 kg Shank diameter: 25 mm Cutting length: 35 mm Number of cutting edges: 2 Special features Internal coolant: yes Compatible inserts: ADKT 1706 Compatible insert manufacturer: Korloy Insert fastening: Torx T15 / M4x10 screw Manufacturer: Teknik Makina SKU: S063TM FAQ Which insert type does the cutter accept? The S063TM accepts ADKT 1706 indexable inserts and is compatible with Korloy insert grades for flexible application choices. Does the tool provide through-tool coolant? Yes — the cutter features internal coolant, which delivers fluid close to the cutting edge to aid cooling and chip evacuation during interrupted or continuous cuts. What are the key dimensions of the shank and cutting zone? The tool has a 25 mm shank diameter and a 35 mm cutting length, with an overall length of 115 mm for compact mounting. How are the inserts secured? Inserts are fixed using a Torx T15 key and an M4x10 screw, offering a secure and repeatable clamping method for routine maintenance. Which manufacturer produces the tool? The shank milling cutter is supplied by Teknik Makina and sold under SKU S063TM for identification and reordering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for AP-- 1604 Indexable Inserts Internal Coolant, 2 Flute - Teknik Makina
Take advantage of a compact, robust milling solution that combines a 25 mm shank, internal coolant and compatibility with AP-- 1604 indexable inserts for reliable cycle times and easier tool management. Order the cutter or request application advice via Metav Werkzeuge for safe selection and fast delivery. Indexable Insert Milling Cutter S256-1TM — 25 mm shank, internal coolant (Teknik Makina) Indexable Insert Milling Cutter S256-1TM is a precision tool for CNC milling operations, designed to accept AP-- 1604 indexable inserts and to improve coolant delivery at the cutting zone 25 mm shank diameter Internal coolant for improved chip control Compatible with AP-- 1604 indexable inserts Secured by M4x10 Torx screw (T15) High-performance milling with stable shank support The cutter delivers a predictable, high-stability performance thanks to its 25 mm shank and compact 120 mm overall length, which reduce overhang and vibration in most machining set-ups. With two effective cutting edges the tool achieves reliable stock removal while maintaining a consistent surface finish. The combination of a solid shank diameter and compact geometry supports higher feed rates and decreases the need for frequent rework, improving throughput in batch and single-piece production. Improved coolant delivery and maintenance benefits Equipped with internal coolant the tool channels cutting fluid directly to the insert flank and the rake face, aiding chip evacuation and reducing heat build-up at the cutting edge. The insert pocket accepts AP-- 1604 indexable inserts (Korloy compatible), which simplifies tool service: worn inserts are replaced quickly rather than regrinding the body. The clamping system uses an M4x10 Torx screw and a T15 key interface for positive torque transmission and straightforward, repeatable insert changes, shortening maintenance cycles and lowering overall tooling costs. Application-oriented design for modern CNC workflows Designed for slotting, ramping and peripheral milling tasks, the cutter integrates easily with standard toolholders used in vertical and horizontal machining centres. The internal coolant capability supports operations that demand controlled thermal conditions and better chip flushing, particularly in continuous production environments. Manufactured by Teknik Makina with a focus on compatibility and serviceability, this milling cutter is suitable where quick insert exchange and process reliability are priorities. Contact Metav Werkzeuge in Emmerich for tailored application advice and to arrange procurement of the S256-1TM — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: S256-1TM Manufacturer: Teknik Makina Type: Indexable insert milling cutter Key figures Diameter: 25 mm Shank diameter: 25 mm Overall length: 120 mm Cutting length (shank): 45 mm Number of cutting edges: 2 Weight: 0.43 kg Screw: M4x10 (Torx T15) Design & special features Internal coolant Compatible with AP-- 1604 indexable inserts Korloy-compatible inserts Torx T15 screw interface FAQ Which inserts are compatible with this cutter? The cutter accepts AP-- 1604 indexable inserts; the S256-1TM is specified for Korloy AP-- 1604 style inserts. Does the tool provide internal coolant? Yes, the S256-1TM features internal coolant, which aids chip evacuation and helps to maintain cutting-edge temperature. What fastening system secures the inserts? Inserts are secured by an M4x10 Torx screw; assembly and torque are applied with a T15 key for reliable clamping. What are the main dimensions to consider for setup? Key dimensions are a 25 mm shank diameter, 120 mm overall length and 45 mm cutting length for tool-setting and holder selection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For AP-- 1604 Indexable Inserts With Internal Coolant, 200mm Overall Length - Teknik Makina
Take advantage of a robust, 25 mm shank combined with internal coolant and direct compatibility with AP-- 1604 Korloy indexable inserts for reliable cycle times and predictable insert life; order via Metav Werkzeuge or consult our specialists for integration advice. Shank milling cutter S276-1TM — 25 mm shank, internal coolant (Teknik Makina) A shank milling cutter designed for use with AP-- 1604 indexable inserts, delivering controlled chip evacuation and stable engagement for precision milling in production and workshop environments. 25 mm shank diameter with 65 mm cutting length Internal coolant for improved chip evacuation Compatible with AP-- 1604 Korloy indexable inserts Robust 200 mm overall length, weight 0.75 kg Consistent chip control for uninterrupted milling The built-in internal coolant directs fluid to the cutting zone, reducing heat and ensuring continuous chip clearance. This improves the cutting environment and helps to extend the service life of the AP-- 1604 inserts. By maintaining lower temperatures at the cutting edge, the tool supports consistent material removal rates and reduces unplanned stoppages, contributing to higher overall equipment effectiveness in serial production. Stable cutting engagement for repeatable accuracy With a 25 mm shank and a 65 mm cutting length, the tool offers a balanced combination of rigidity and reach that reduces deflection during plunging and peripheral milling operations. The two cutting edges provide a predictable load per tooth and help to maintain surface finish and dimensional accuracy. Fast, secure clamping is facilitated by the included T15 Torx key and the M4x10 Torx screw specification, enabling quick insert changes and minimal downtime. Designed for workshop throughput and simple tool management The milling tool’s geometry and compatibility with Korloy inserts allow straightforward stocking of commonly used indexable parts, simplifying tool inventory and tool-change routines. At 200 mm overall length and 0.75 kg weight the component is manageable in manual handling and suitable for automated changer systems where a compact, serviceable tool is required. The clear interchangeability with standard AP-- 1604 indexable inserts supports efficient replenishment and consistent performance across batches. For procurement or technical integration of the Teknik Makina indexable milling solution, contact Metav Werkzeuge for expert advice and order support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S276-1TM Manufacturer: Teknik Makina Compatible inserts: AP-- 1604 (Korloy) Torx key: T15 Torx screw: M4x10 Dimensions & weight Diameter: 25 mm Shank diameter: 25 mm Overall length: 200 mm Cutting length: 65 mm Number of cutting edges: 2 Weight: 0.75 kg Features & functions Internal coolant Indexable milling cutter design Suited for AP-- 1604 Korloy indexable inserts Product type: Shank milling cutter FAQ What insert type is required for this cutter? The cutter is designed for AP-- 1604 indexable inserts; Korloy inserts are specified as compatible. Does the tool provide coolant supply to the insert seat? Yes, the tool features internal coolant to direct fluid to the cutting zone and aid chip evacuation. What are the key mounting and replacement parts? Insert fastening uses a Torx M4x10 screw; the corresponding Torx key size is T15. Is the shank suitable for standard 25 mm tool holders? The tool has a 25 mm shank diameter, matching standard 25 mm holders for secure clamping. How many cutting edges does the cutter have and what does that mean for machining? The tool has 2 cutting edges; this provides stable engagement and predictable load per tooth for repeatable machining results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For APKT 1003 Indexable Inserts With Internal Coolant, 150mm Overall Length - Teknik Makina
For reliable throughput choose the combination of a 25 mm shank, internal coolant and APKT 1003 compatibility for stable, efficient indexable insert milling. Order the shaft milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shaft milling cutter S180-2TM — 25 mm shank, internal coolant (Teknik Cutting Tools) A shaft milling cutter S180-2TM for APKT 1003 indexable inserts, engineered for industrial CNC milling where quick insert changes and controlled chip evacuation are essential. 25 mm shank diameter Internal coolant supply Compatible with Korloy APKT 1003 inserts Total length 150 mm, 3 cutting edges Stable cutting and longer insert life through internal coolant The integrated internal coolant channel delivers coolant directly to the cutting zone, reducing thermal load on the insert and workpiece. This targeted cooling helps to maintain cutting-edge geometry under higher cutting speeds, which translates into longer insert life and fewer tool changes. For industrial production settings the result is a measurable reduction in downtime and improved process stability when paired with robust fixtures and proper spindle setup. Robust shank and simple fastening for reliable clamping A 25 mm shank and a total length of 150 mm provide a balance between reach and rigidity, reducing deflection in medium-duty milling tasks. The cutter uses a Torx T8 fastening system with M2.5x5.5 screws, enabling secure clamping of APKT 1003 inserts and straightforward maintenance. Clear torque settings and correct toolholder clamping are decisive for repeatable concentricity and consistent surface finishes in serial production. Designed for fast insert changes and consistent productivity Compatibility with APKT 1003 indexable inserts (manufacturer: Korloy) means insert changes are rapid and economical: worn edges are replaced rather than the whole tool body. The three cutting edges configuration supports uninterrupted chip flow and stable engagement for a wide range of flank angles. In production terms this leads to reduced tool inventory costs and faster return to operation after wear-related interventions. Practical maintenance and workshop handling Maintenance is facilitated by the standardised screw and key sizes, which keep service times short and predictable. The tool’s 0.563 kg weight and standard shank dimensions simplify handling and toolchanger programming. Routine checks of the coolant passage and screw torque are sufficient to retain optimal performance, while replacing inserts restores original cutting geometry without complex recalibration. For a dependable, high-performance milling solution from Teknik Cutting Tools, contact Metav Werkzeuge for product availability and application advice supplied from Emmerich. Technical data SKU: S180-2TM UID: S180-2TM Product type: Shaft milling cutter Manufacturer: Teknik Cutting Tools Brand: Teknik Makina Compatible inserts: APKT 1003 (Korloy) Internal coolant: yes Torx key: T8 Torx screw: M2.5x5.5 Facts Shank diameter: 25 mm Total length: 150 mm Cutting length: 60 mm Number of cutting edges: 3 Weight: 0.563 kg Special features Internal coolant supply Compatible with Korloy APKT 1003 indexable inserts Torx fastening system for secure clamping Indexable insert milling design SKU for ordering: S180-2TM FAQ What insert type does the cutter accept? The cutter accepts APKT 1003 indexable inserts; compatibility is specified for Korloy inserts and standard APKT seating dimensions. Is the tool supplied with cooling capability? Yes, the tool features an internal coolant channel that directs coolant to the cutting zone for thermal control and improved insert life. Which toolholder size is required for secure mounting? The cutter uses a 25 mm shank, requiring a matching 25 mm toolholder or collet with appropriate clamping for safe operation. How many cutting edges does the cutter have and what is the effect? The cutter is equipped with three cutting edges, offering a balance between chip evacuation and cutting stability for consistent results in serial milling. Which screw and key are used for insert fastening? Insert fastening uses a Torx T8 key and M2.5x5.5 screws, enabling secure, standardised insert clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For APKT 1003 Indexable Inserts With Internal Coolant, 3-Flute - Teknik Makina
Take advantage of the combination of internal coolant and a 25 mm rigid shank for steady, high-performance milling with fast insert changes. Order the tool directly via Metav Werkzeuge or contact our consultants for application-specific recommendations. End mill S169-1TM – 25 mm, internal coolant (Teknik Makina) The End mill S169-1TM is a 25 mm shank milling tool designed for indexable machining with APKT 1003 inserts, ideal for precision face and shoulder milling in industrial workshops Internal coolant for secure tool cooling 25 mm shank for rigid clamping Compatible with APKT 1003 indexable inserts Three cutting edges for stable material removal Increase throughput with optimised cooling and tool life The internal coolant supply reduces cutting temperatures at the insert edge, which directly contributes to longer tool life and more consistent cycle times. By keeping the cutting zone flushed and cooled, the design supports higher metal removal rates without premature wear, while the compatibility with APKT 1003 inserts enables a wide choice of grades for different materials. This combination converts thermal control into measurable productivity gains on the shop floor. Better accuracy through rigid shank and stable geometry A 25 mm shank and compact body deliver rigid clamping, lowering the risk of chatter and improving dimensional stability during aggressive cuts. The three-edge configuration and 40 mm cutting length balance cutting capacity with vibration resistance, resulting in cleaner surfaces and tighter tolerances. For setups where repeatability matters, the cutter’s geometry turns machine capability into reliable, reproducible results. Fast serviceability and application flexibility Designed for quick insert changes, the tool uses a Torx T8 drive and an M2.5x5.5 fastening screw to keep maintenance times short and downtime minimal. The tool’s 120 mm overall length and compatibility with Korloy-manufactured APKT 1003 inserts make it suitable for a variety of milling tasks in production and repair environments. Simple handling and standardised parts reduce toolroom complexity and support efficient tool management. For application advice or to arrange supply of the S169-1TM end mill from Metav Werkzeuge’s Emmerich stock, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical guidance and supply options. Technical Data Article number: S169-1TM Manufacturer: Teknik Makina Product type: End mill for indexable inserts For inserts: APKT 1003 Facts Diameter: 25 mm Shank diameter: 25 mm Overall length: 120 mm Cutting length (shank): 40 mm Weight: 0.452 kg Cutting edges: 3 ECLASS: 21180806 Special features Internal coolant Compatible insert manufacturer: Korloy Torx key: T8 Torx screw: M2.5x5.5 FAQ Is the S169-1TM compatible with APKT 1003 inserts? The S169-1TM end mill is designed specifically for APKT 1003 indexable inserts and supports Korloy-manufactured variants. Does the cutter provide internal coolant delivery? Yes, the S169-1TM features internal coolant to improve chip evacuation and reduce thermal load at the cutting edge. What shank diameter is required for clamping? This end mill has a 25 mm shank diameter and is intended for holders that accept a 25 mm shank for rigid clamping. How many cutting edges does the tool have? The S169-1TM is equipped with three cutting edges, offering stable material removal and balanced cutting forces. Which fastening tool is needed for insert changes? Insert fastening on the S169-1TM is performed with a Torx T8 driver using an M2.5x5.5 screw for secure and quick replacement. What is the overall length and cutting length of the tool? The end mill has a 120 mm overall length and a 40 mm cutting length, providing a compact profile with sufficient reach for many milling operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For APKT 1003 Indexable Inserts, 3 Flutes 90° Cutting Angle - Teknik Makina
Take advantage of the combination of high rigidity, precise insert compatibility and straightforward maintenance to keep production running smoothly; the 25 mm shank and 3-cut configuration ensure stable chip evacuation and repeatable results. Order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Indexable shank cutter (Schaftfräser) for APKT 1003–1604 — 25 mm shank, 3-flute | Teknik Makina The Indexable shank cutter (Schaftfräser) is a compact milling solution designed for use with APKT 1003–1604 indexable inserts, aimed at efficient shoulder and face milling in CNC and milling centres. 25 mm shank diameter 3 cutting edges for stable machining Compatible with APKT 1003–1604 inserts (YG‑1) 90° cutting angle for shoulder milling Consistent rigidity and predictable cutting performance for reliable production The tool’s 25 mm shank and overall 100 mm length combine to give a stiff, compact assembly that reduces chatter and improves surface finish compared with longer, slender holders. Fitted for APKT-type indexable inserts, the cutter converts insert geometry into consistent cutting results: the 3 cutting edges support balanced load distribution and improved tool life when compared with higher-flute tools in similar diameters. For operators unfamiliar with indexable systems, APKT inserts are mounted and secured on a pocketed cutter body, enabling straightforward replacement of the wear element without regrinding, which reduces setup time and maintains reproducible geometry across batches. Quick insert changes and secure fastening to cut downtime Insert replacement is achieved using the supplied Torx fastening arrangement: the M2.5x7 Torx screw kept under the insert pocket and a T8 Torx key for secure tightening. This familiar clamping standard minimises the risk of incorrect torque and secures repeatable seating of the insert, which is critical for precision work. The indexable concept allows rapid switching between insert grades and chipbreaker geometries when moving from finishing to roughing operations. The result is a system that supports planned maintenance practices and keeps spindle time productive, delivering measurable throughput improvements in job-shop and production environments. Application-focus: geometry, reach and working angle explained A 90° cutting angle means the cutter is optimised for shoulder milling and accurate face operations where square shoulders and tight tolerances matter. The 35 mm cutting length provides sufficient engagement for shallow slots and shoulder passes while limiting overhang that can compromise stiffness. Weighing 0.376 kg and featuring a nominal 25 mm diameter, the tool is suited to medium-duty milling work where indexable insert economics are preferred. Operators selecting insert grade and coating should pair the cutter with APKT 1003–1604 inserts from recognised suppliers such as YG‑1 to match workpiece material and cutting conditions for best results. For application support or to specify the Teknik Makina indexable shank cutter for a particular machine or material, contact Metav Werkzeuge for tailored advice via email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants assist with insert selection and process integration. Technical data SKU: S033TM Manufacturer: Teknik Makina Article designation: Indexable shank cutter for APKT 1003–1604 indexable inserts Facts Shank diameter: 25 mm Cutting length (shank): 35 mm Overall length: 100 mm Diameter: 25 mm Cutting edges: 3 Weight: 0.376 kg Cutting angle: 90° Special features Compatible with APKT 1003–1604 indexable inserts Insert supplier: YG-1 Torx screw: M2.5x7 Torx key size: T8 FAQ What types of inserts fit this cutter? The cutter accepts APKT 1003–1604 indexable inserts; compatibility is specified to those APKT sizes and standard geometries. Is a specific torque required for the Torx screw? Use the recommended Torx key size T8 and ensure the M2.5x7 screw is tightened to the insert supplier’s torque guidance to guarantee correct seating and repeatable results. Can the cutter be used for shoulder milling on hardened materials? The tool’s 90° cutting angle suits shoulder milling, but for hardened materials consult the insert grade and coating recommendations; Metav Werkzeuge can advise on suitable insert choices. What are the key dimensions to check when selecting this holder? Key dimensions are 25 mm shank diameter, 35 mm cutting length, 100 mm overall length and the nominal 25 mm cutter diameter; these define reach, rigidity and machine-holding requirements. Which insert manufacturers pair well with this cutter? The tool is specified as compatible with APKT inserts and is commonly used with inserts from suppliers such as YG‑1; Metav Werkzeuge can recommend alternative insert brands and grades. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For APMT 1604 Indexable Inserts, 2 Flutes, 90° Cutting Angle, 45mm Cutting Length - Teknik Makina
Take advantage of the secure Torx clamping, 25 mm shank rigidity and 45 mm effective cutting length to maintain consistent shoulder milling in high-grade steel; the result is reliable cycle times and straightforward insert changes. Order the shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shank milling cutter S244TM – 90° cutter for APMT 1604 indexable inserts (Teknik Makina) Shank milling cutter S244TM for 90° shoulder milling with APMT 1604 indexable inserts, suitable for high-class steel machining and workshop applications 25 mm shank diameter 45 mm effective cutting length 90° cutting angle for square shoulders Compatible with APMT 1604 Korloy inserts Secured with M4x10 Torx screw, T15 key Robust performance for demanding steel machining The S244TM is designed for stable shoulder milling where rigidity and repeatability matter. With a 25 mm shank and a 45 mm cutting length, the tool body limits deflection during interrupted cuts, helping to maintain dimensional accuracy on components made from high-grade steels. The 90° cutting angle produces true square shoulders without additional finishing passes, reducing cycle times and improving throughput for batch production or repair work. Secure clamping and precise geometry for reliable inserts Clamping is achieved with an M4x10 Torx screw and a T15 key, providing a secure, torque-friendly interface that minimises insert movement under load. The body carries two cutting edges, arranged for balanced cutting forces, and the overall length of 120 mm contributes to familiar tool set-ups in milling heads and arbors. A net weight of 0.43 kg gives a tangible sense of robust construction while remaining easy to handle during tool changes. Compatibility and cost-effective indexable insert use Configured for APMT 1604 indexable inserts and compatible with Korloy plates, the cutter supports quick insert replacement to restore cutting performance without swapping the whole tool body. Indexable inserts offer economical cutting-edge renewals and a range of geometry options for specific material finishes. Paired with Metav’s reliable supply chain and stock management, this configuration supports consistent workshop performance and predictable reordering cycles. For dependable 90° shoulder milling from Teknik Makina, contact Metav Werkzeuge for personalised advice and fast delivery — info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: S244TM Manufacturer: Teknik Makina Brand: Teknik Makina SKU: S244TM Facts Shank diameter: 25 mm Effective cutting length: 45 mm Overall length: 120 mm Cutting edges: 2 Weight: 0.43 kg Cutting angle: 90° Special features For APMT 1604 indexable inserts Compatible with Korloy inserts Torx screw M4x10 Torx key T15 ECLASS: 21180806 ETIM: EC011860 FAQ What materials is this cutter suited for? The S244TM is specified for high-class steel machining and is designed to deliver stable performance when machining steel grades commonly found in industrial applications. Which inserts fit this cutter? This cutter accepts APMT 1604 indexable inserts and has proven compatibility with Korloy plates in the APMT 1604 format. How is the insert secured in the cutter? Inserts are fastened with an M4x10 Torx screw; the recommended bit for removal and installation is a T15 key to ensure consistent clamping force. What are the key dimensions to consider for tool set-up? Important dimensions include a 25 mm shank diameter, 45 mm effective cutting length, and 120 mm overall length, which help determine suitability for specific milling holders and reach requirements. Is this cutter available for immediate delivery? Stock and delivery options depend on Metav Werkzeuge’s warehouse availability; the product listing notes rapid dispatch from the Emmerich stock for standard orders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for BDMT 1704 Indexable Inserts Internal Coolant, 2 Flute - Teknik Makina
Take advantage of a robust combination of a 25 mm shank, internal coolant and a 120 mm overall length to improve tool stability and reduce changeovers; order the shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shank milling cutter for BDMT 1704 indexable inserts — 25 mm, internal coolant (Teknik Makina) A shank milling cutter designed for secure clamping and efficient coolant-fed machining with BDMT 1704 indexable inserts in general machining applications. 25 mm shank diameter for secure clamping Internal coolant for reliable chip evacuation Compatible with BDMT 1704 inserts (Kyocera) 120 mm overall length, 35 mm cutting length Precision and performance for productive milling The tool delivers consistent cutting performance thanks to its 25 mm shank and compact geometry. A sturdy shank diameter increases clamping rigidity, which in turn reduces vibration and improves surface finish during interrupted or continuous milling. With 2 cutting edges, the cutter offers an effective balance between metal removal rate and economical insert usage, enabling predictable cycle times on CNC milling machines and workshop mills. Controlled coolant for consistent surface quality Integrated internal coolant channels supply coolant directly to the cutting zone, improving chip evacuation and heat control at the insert edge. This targeted coolant feed reduces built-up edge and helps maintain flank and rake face condition, which extends insert life and reduces downtime for tool changes. The design also lowers the risk of recutting chips, producing a more consistent surface quality across batches. Insert compatibility and straightforward servicing The diameter and pocket geometry are configured for BDMT 1704 indexable inserts and are compatible with inserts from Kyocera, simplifying procurement and stocking. Replacement and clamping use a Torx drive (T15) and M4x8.5 screw for secure, repeatable fixing of the insert heads; this results in quick servicing intervals and predictable torque values for assembly. The cutter’s SKU S578-1TM identifies the configuration for ordering and spare-part matching. Reach, rigidity and workshop advantages With a 120 mm overall length and 35 mm cutting length, the tool provides useful reach without compromising stiffness for many slotting and face-milling tasks. The combination of compact length and coolant-fed design supports higher productivity on medium-duty operations while maintaining process reliability. The modest mass and proven geometry also make the tool a pragmatic choice for consolidating tool assortments in a busy production environment. For precision milling with internal coolant and reliable insert compatibility, contact Metav Werkzeuge to discuss the Teknik Makina S578-1TM shank milling cutter and delivery options from Emmerich. Technical data Article number: S578-1TM Product type: Shank milling cutter Manufacturer: Teknik Makina Facts Diameter: 25 mm Shank diameter: 25 mm Overall length: 120 mm Cutting length (shank): 35 mm Number of cutting edges: 2 Weight: 0.432 kg Special features Internal coolant: yes Compatible inserts: BDMT 1704 Compatible insert manufacturer: Kyocera Torx key: T15 Torx screw: M4x8.5 FAQ What insert type does this cutter use? The cutter is configured for BDMT 1704 indexable inserts; Kyocera-compatible grades are commonly fitted to this tool. Is the coolant internal or external? This model features internal coolant, supplying fluid directly to the cutting edge to assist chip removal and edge life. How is the insert secured and which tools are required? Inserts are fixed with an M4x8.5 screw driven by a T15 Torx key for secure, repeatable clamping on the S578-1TM. What are the key dimensions to check before mounting? Check the 25 mm shank diameter, 120 mm overall length and the 35 mm cutting length to ensure suitable clearance and rigidity on the machine. Is this tool suitable for high-production environments? The coolant-fed design and robust shank make this cutter appropriate for repetitive milling tasks where reduced tool changes and consistent edge performance are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for BLMP 0603 Indexable Inserts With Internal Coolant, 150mm - Teknik Makina
Take advantage of a rigid 25 mm shank combined with internal coolant and a compact 30 mm cutting length for stable, high-output milling operations; order directly via Metav Werkzeuge or contact our consultants for application advice. Shank cutter S483-1TM – for BLMP 0603 indexable inserts, internal coolant (Teknik Makina) Shank cutter S483-1TM is a purpose-built 25 mm shank milling cutter for BLMP 0603 indexable inserts, designed for reliable chip evacuation and consistent tool performance in demanding production settings. *25 mm shank diameter for rigid toolholding *Internal coolant for improved tool life *Compatible with BLMP 0603 indexable inserts *150 mm overall length with 4 cutting edges Consistent cooling and stable chip evacuation Equipped with internal coolant, this tool channels cutting fluid directly to the cutting zone to reduce heat generation and support stable chip formation. The controlled coolant supply helps to extend insert life and maintain a consistent surface finish under continuous machining, which in turn improves process reliability and reduces unscheduled tool changes. The tool’s fluid-fed design is particularly effective where thermal stability is critical for dimensional accuracy. Secure clamping and straightforward insert system The 25 mm shank provides a rigid connection to the toolholder for minimal deflection at higher feeds, enabling more aggressive cutting parameters where chassis stiffness permits. Inserts are secured with an M3x6.2 screw tightened using a Torx T8, allowing quick, repeatable clamping and reduced changeover times. The cutter accepts BLMP 0603 indexable inserts and is compatible with inserts from Taegutec, facilitating supply chain flexibility for production customers. Efficient cutting geometry for reliable material removal Featuring 4 cutting edges, the cutter balances material removal rate with tool life, enabling steady performance across longer tool runs. The design concentrates the cutting forces into a compact 30 mm cutting length, which helps maintain rigidity in slotting and light shoulder milling operations. Surge suppression during intermittent cuts is achieved through harmonised geometry, delivering repeatable results and predictable tool wear patterns for process planning. Low-maintenance operation and fast serviceability The retention system and internal coolant routing are engineered for straightforward maintenance: inserts are replaceable without disturbing the tool’s mounting, and the internal coolant ports reduce external clogging. The combination of accessible fasteners and a standardised insert system reduces downtime and simplifies inventory management on the shop floor, supporting higher machine utilisation and more consistent throughput. For reliable production performance with the Teknik Makina shank cutter featuring internal coolant, contact Metav Werkzeuge for tailored technical advice or to arrange supply from our Emmerich warehouse — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: S483-1TM Product type: Shank cutter Designation: for BLMP 0603 indexable inserts Manufacturer: Teknik Makina Facts Diameter: 25 mm Overall length: 150 mm Shank diameter: 25 mm Cutting length: 30 mm Cutting edges: 4 Weight: 0.281 kg Special features Internal coolant Compatible inserts: BLMP 0603 Compatible insert manufacturer: Taegutec Torx key: T8 Fastening screw: M3x6.2 FAQ What inserts fit this cutter? The shank cutter S483-1TM accepts BLMP 0603 indexable inserts and is specified to be compatible with Taegutec insert grades. Is coolant routed through the tool? Yes, the tool features internal coolant to deliver cutting fluid directly to the cutting zone for improved insert life and consistent results. What is the shank size and how does it affect performance? The tool has a 25 mm shank, offering rigid clamping to reduce deflection and enable stable machining at elevated feed rates. How many cutting edges are available and what are the benefits? The cutter has 4 cutting edges, balancing material removal rate with economical insert usage and predictable wear behaviour. Which fastener and key are required for insert changes? Insert fixation uses an M3x6.2 screw and is tightened with a Torx T8, ensuring secure and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For LNMU 0303 Indexable Inserts With Internal Cooling, 4 Flutes - Teknik Makina
Take advantage of stable clamping, a 25 mm shank and internal coolant for reliable, high‑throughput milling. Benefit from compatibility with LNMU 0303 indexable inserts and the proven supply chain of Metav Werkzeuge — order directly via Metav Werkzeuge or request tailored advice from our consultants. Shank milling cutter for LNMU 0303 indexable inserts by Teknik Makina — 25 mm shank, internal coolant The Shank milling cutter is a precision tool designed for milling operations using LNMU 0303 indexable inserts, optimised for stable clamping and effective coolant delivery. 25 mm shank diameter Internal coolant supply Compatible with LNMU 0303 inserts Torx T8 fastening, M2.5x7 screws Precise insert compatibility for predictable production results This milling tool is engineered to accept LNMU 0303 indexable inserts, ensuring repeatable geometry and quick insert changes. The combination of a 25 mm shank and a well‑balanced cutter body reduces vibration and improves surface finish, which directly supports consistent cycle times and fewer rejected parts. For workshops and production lines that require predictable outcomes, the design translates into lower setup variance and faster changeover between jobs. Internal coolant for improved edge life and chip control Equipped with internal coolant, the cutter directs fluid close to the cutting zone to reduce tool temperature and flush chips efficiently from the insert pocket. This cooling method helps extend insert life and maintain cutting performance during longer operations, decreasing unplanned stoppages. The result is a measurable improvement in throughput where thermal stability and chip evacuation are critical to maintain tolerances and surface quality. Simple, secure fastening and maintenance for minimal downtime Assembly and insert replacement are straightforward: the cutter uses a Torx T8 key and M2.5x7 screws for secure fixation. With four cutting edges and a 60 mm cutting length, the geometry supports both roughing and light finishing passes when paired with appropriate inserts. The accessible fastening system minimises maintenance time and reduces the risk of incorrect assembly, which is beneficial for busy toolrooms and production environments where uptime is essential. Suited to industrial milling workflows and quick changeovers Designed for use in workshop and industrial milling setups, this shank milling design supports fast insert swaps and integration into toolholder systems common on milling machines. The tool’s specifications, including overall length and shank stability, make it a practical choice for repetitive production tasks where tool reliability and consistent clamping are priorities. Combined with compatible inserts from recognised manufacturers, it contributes to an efficient tooling concept that reduces inventory complexity. Contact Metav Werkzeuge today to discuss technical matching with existing toolholders or to request matched insert recommendations based on Teknik Makina’s shank milling cutter; reach our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: S675-1TM Manufacturer: Teknik Makina Product type: Shank milling cutter Designation: Schaftfräser for LNMU 0303 Indexable Inserts Dimensions & Core Data Diameter: 25 mm Overall length: 150 mm Shank diameter: 25 mm Cutting length: 60 mm Number of cutting edges: 4 Weight: 0.589 kg Features & Compatibility Internal coolant: Yes Compatible inserts: LNMU 0303 Compatible insert manufacturer: Tungaloy Torx key: T8 Torx screw: M2.5x7 FAQ Is this cutter compatible with Tungaloy LNMU 0303 inserts? Yes. The shank milling cutter is designed for LNMU 0303 indexable inserts and is listed as compatible with inserts from Tungaloy; use the specified insert type for correct fit and performance. Does the tool provide internal coolant supply? Yes. The cutter features internal coolant to direct fluid to the cutting zone for improved tool life and chip evacuation. What fastening hardware is required for the inserts? Insert fastening uses a Torx T8 key with M2.5x7 screws; the cutter is supplied to accept this standard fastening configuration for secure, repeatable clamping. What are the key dimensions to consider when planning toolholders? Key dimensions are a 25 mm shank diameter, 150 mm overall length and a 60 mm cutting length; consult these values when selecting a compatible toolholder or extension. Which SKU and manufacturer details identify this item? The tool is listed under SKU S675-1TM and supplied by Teknik Makina; these identifiers should be used when ordering or requesting technical data. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm End Mill for LNMX 1004 Indexable Inserts Internal Coolant, 200mm Overall Length - Teknik Makina
Take advantage of the combination of internal coolant, 25 mm shank stability and compatibility with LNMX 1004 indexable inserts for reliable, high‑feed milling; order the cutter directly via Metav Werkzeuge or consult our technical advisers for application support. Indexable Insert Milling Cutter S094TM — 25 mm shank, internal coolant (Teknik Makina) The Indexable Insert Milling Cutter S094TM is a shank milling cutter engineered for use with LNMX 1004 indexable inserts, offering coolant‑fed chip evacuation and a compact, rigid design for general machining operations. 25 mm shank diameter for stable clamping Internal coolant for efficient chip control Compatible with LNMX 1004 inserts by Korloy Secure clamping with Torx T15 screws M4x10 Boosted productivity through coolant‑fed cutting The combination of an internal coolant channel and a rigid 25 mm shank delivers measurable improvements in process stability and tool life. By supplying coolant directly to the cutting zone, the tool reduces thermal load on the insert and promotes chip evacuation, which supports longer uninterrupted cutting cycles and fewer insert changes. This design suits medium‑duty milling operations where consistent surface finish and repeatable dimensions are required; the result is increased throughput with lower overall tooling costs. Secure clamping and simple maintenance for reduced downtime Engineered for dependable clamping, the cutter uses Torx T15 drive screws (M4x10) to fix the insert seats, enabling fast, repeatable indexation. The three cutting edges provide balanced engagement and smooth cutting forces, while the 80 mm cutting length gives a practical reach for shoulder and face milling tasks. Maintenance is straightforward: replace or index the LNMX 1004 inserts and retorque the Torx screws to restore original cutting performance, reducing non‑productive time and tooling overhead. Application confidence and compatibility with Korloy inserts Designed around the LNMX 1004 insert geometry and compatible with Korloy manufacture, this milling head ensures a reliable fit and predictable cutting behaviour. The modular approach of using indexable inserts allows quick adaptation to differing materials or surface‑quality targets by selecting the appropriate grade. Combined with a 200 mm overall length and a compact 25 mm shank, the assembly balances reach and rigidity for stable machining across a range of common workshop tasks. Why the technical details matter for procurement and shop floor results Specifying a tool with documented features—internal coolant, standard Torx fixing, and proven insert compatibility—translates into fewer interfaces to manage, simplified stock lists and more predictable machining outcomes. For purchasing and planning, the S094TM offers a pragmatic balance of serviceability and performance: short changeover procedures, established insert formats and a compact form factor reduce risk in production planning and inventory management. Contact Metav Werkzeuge to discuss the S094TM with internal coolant and LNMX 1004 compatibility, or request application advice from our specialists for a tailored machining strategy. Technical data Article number: S094TM Manufacturer: Teknik Makina Product type: Indexable insert milling cutter Dimensions & measurable data Shank diameter: 25 mm Overall length: 200 mm Cutting length (shank to cutting area): 80 mm Weight: 0.6 kg Number of cutting edges: 3 Materials & special features Internal coolant: yes Suitable insert geometry: LNMX 1004 Compatible insert supplier: Korloy Torx key: T15 Torx screw: M4x10 FAQ What insert type does this milling cutter use? The milling cutter accepts LNMX 1004 indexable inserts; the tool body S094TM is designed to clamp that geometry securely. Is internal coolant available and how does it help? Yes, the S094TM features internal coolant to cool the cutting zone and improve chip evacuation, which extends insert life and enhances surface finish. What shank size is required for the holder? This cutter has a 25 mm shank diameter and is best used in holders compliant with that shank size for optimal rigidity. How many cutting edges does the tool provide? The cutter is configured with three cutting edges, offering balanced cutting forces and efficient material removal for face and shoulder milling. Which screw type is used for insert clamping? Insert clamping uses Torx T15 drive screws in M4x10 size for secure and repeatable fixation. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for LNMX 1006 Indexable Inserts Internal Coolant, 120mm - Teknik Makina
Combining the rigidity of a 25 mm shank, internal coolant and compatibility with LNMX 1006 inserts, this shank cutter ensures stable chip control and consistent machining results; order the tool directly via Metav Werkzeuge or consult our technical team for application-specific advice. Schaftfräser – Shank cutter for LNMX 1006 indexable inserts, 25 mm shank, internal coolant (Teknik Makina) Schaftfräser designed as an indexable-insert shank cutter for medium-duty milling operations, offering internal coolant and a compact 120 mm overall length for use in confined toolholders. Internal coolant for efficient tool cooling 25 mm shank for rigid clamping Compatible with LNMX 1006 Korloy inserts Three cutting edges for stable material removal Increased stability through a compact, rigid design The tool's 25 mm shank and balanced geometry deliver high rigidity at the spindle, reducing deflection during interrupted cuts and improving dimensional consistency. With a 120 mm total length and a 40 mm cutting length, the cutter provides a pragmatic combination of reach and stiffness for confined setups. This design reduces vibration and supports repeatable surface finishes, translating technical specifications into measurable production benefits such as reduced scrap rates and simplified process setup. Improved cooling and chip evacuation for longer cutting intervals Equipped with internal coolant, the cutter directs cutting fluid close to the cutting zone, which aids lubrication, reduces heat build-up and helps evacuate chips efficiently. The insert system accepts LNMX 1006 indexable inserts from Korloy, allowing the use of latest grades and geometries for different materials. The tool features three cutting edges, which balance cutting forces and improve feed smoothness; combined with secure fastening via T8 Torx and an M3x7 screw, this provides consistent insert clamping and straightforward replacement during scheduled maintenance. Serviceability and predictable performance for production workflows Designed for pragmatic workshop routines, the shank cutter simplifies insert changes and inspection, supporting predictable cycle times. The item is identified as LN102-1TM for ordering and inventory control and has a mass of 0.453 kg, which contributes to stable dynamic behaviour in many spindle configurations. The combination of indexable-insert flexibility and coolant-fed tool-body ensures operators can adapt cutting strategies while maintaining tool life and process stability — a rational investment for CNC centres seeking dependable output and lower per-part costs. Contact Metav Werkzeuge for an expert recommendation on applying this Teknik Makina shank cutter in specific workflows and to arrange fast delivery from our Emmerich warehouse Technical data SKU: LN102-1TM Product type: Shank cutter (indexable inserts) Manufacturer: Teknik Makina ECLASS: 21180806 Facts Shank diameter: 25 mm Total length: 120 mm Cutting length: 40 mm Number of cutting edges: 3 Weight: 0.453 kg Features Internal coolant: yes Compatible inserts: LNMX 1006 Compatible insert manufacturer: Korloy Fastening: T8 Torx with M3x7 screw Label: 25mm shank cutter LNMX 1006 L120mm with internal coolant FAQ Is this cutter compatible with Korloy LNMX 1006 inserts? Yes. The cutter is specified for LNMX 1006 indexable inserts and is compatible with Korloy insert geometries as stated in the product data. What Torx key and screw are required for insert replacement? Insert fastening on this shank cutter requires a T8 Torx key and M3x7 screw, enabling secure and repeatable clamping. What are the tool dimensions and how do they affect stiffness? The tool has a 25 mm shank, 120 mm total length and 40 mm cutting length; these dimensions provide a balanced compromise between reach and rigidity suitable for many medium-duty milling tasks. Can this cutter improve cycle times compared with solid-end mills? By using indexable inserts and targeted coolant delivery, the cutter can increase cutting intervals and reduce downtime for tool changes, which contributes to more efficient cycle times in production environments. Is the item listed for straightforward procurement and inventory control? Yes. The cutter is supplied as LN102-1TM, which simplifies ordering and stock management for workshop procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For LNMX Indexable Inserts 3 Flutes 40mm Cutting Length 120mm Overall Length 90° Cutting Angle - Teknik Makina
Take advantage of a robust combination of 25 mm shank rigidity, a 40 mm cutting length and compatibility with LNMX 1006 indexable inserts for reliable, repeatable milling cycles; order or request technical advice via Metav Werkzeuge for seamless integration. Teknik Makina Shaft cutter LN102TM — for LNMX indexable inserts, 25 mm shank The Shaft cutter LN102TM is a tool for indexable-insert milling, designed for secure clamping and efficient material removal in professional workshop and production environments. 25 mm shank diameter for rigid clamping 40 mm cutting length for deeper engagement Compatible with LNMX 1006 indexable inserts Includes M3x7 Torx screw and T8 key Precision and secure insert clamping for consistent component quality The LN102TM is built around a 25 mm shank and a 90° cutting angle, offering stable support in the spindle and predictable cutting forces. Compatibility with LNMX 1006 indexable inserts enables quick insert changes and consistent edge geometry without regrinding, which reduces setup time and maintains dimensional accuracy across batches. The tool is supplied with an M3x7 Torx screw and T8 key, ensuring the insert is secured to specification; this arrangement supports repeatable clamping torque and reduces the risk of insert movement during interrupted cuts. Such design choices are intended to deliver consistent surface finish and repeatable cycle times in series production. Improved material evacuation and access for demanding operations With three cutting edges and a 40 mm cutting length, this cutter balances chip evacuation and cutting stability. The flute count and geometry are selected to aid chip flow while preserving tool strength, making the tool suitable for heavier feed rates where rigid clamping is present. The 120 mm overall length provides additional reach for operations where access is constrained, while the relatively light mass of 0.453 kg contributes to lower spindle load during acceleration and reduces inertial forces on the toolholder. Where short tool-change times are required, the indexable system minimises downtime, increasing uptime and machining throughput. Practical fit for production workshops and insert systems Specified for use with Korloy-manufactured inserts and described as compatible with LNMX 1006 plates, this cutter is intended for professionals who value straightforward integration into existing insert programmes. The combination of standardised insert format and Torx clamping simplifies inventory management: spare screws and keys are common items in maintenance kits. The cutter’s construction supports reliable tool life under stable cutting conditions; routine checks of screw torque and insert condition are recommended to maintain peak performance and avoid unexpected tool-related interruptions. Contact Metav Werkzeuge for tailored advice and prompt supply from Emmerich — technical consultants can confirm suitability for specific machining tasks and arrange delivery of the LN102TM with the necessary accessory parts Technical Data SKU: LN102TM Manufacturer: Teknik Makina Product type: Shaft cutter for LNMX indexable inserts Compatibility: LNMX 1006 Supplied fixing: M3x7 Torx screw, T8 key Facts Shank diameter: 25 mm Cutting length: 40 mm Total length: 120 mm Diameter: 25 mm Number of cutting edges: 3 Weight: 0.453 kg Cutting angle: 90° Special features Suitable for Korloy indexable inserts Indexable-insert system (LNMX 1006) Torx clamping hardware included Brand: Teknik Makina FAQ What insert type is required for this cutter? The cutter accepts LNMX 1006 indexable inserts; compatibility with Korloy inserts is specified for the LN102TM. How is the insert secured to the cutter head? An M3x7 Torx screw fastens the insert; the tool is supplied with a T8 key for correct tightening. What are the key dimensions to check for toolholder compatibility? Check the 25 mm shank diameter and 120 mm overall length to ensure correct fit and sufficient reach in the toolholder. Is the cutter suitable for use in production with frequent insert changes? Yes — the indexable design and standardised clamping make the tool appropriate for production environments requiring fast insert replacement and consistent repeatability. What benefit does the 40 mm cutting length provide? The 40 mm cutting length increases axial engagement for deeper cuts or step milling operations while maintaining rigidity when used with suitable holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For R390 11T3 Indexable Inserts With Internal Cooling, 45mm Cutting Length - Teknik Makina
Robust machining performance with a 25 mm shank, integrated internal coolant and compatibility with R390 11T3 indexable inserts for efficient tool changes and extended insert life — order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Shank milling cutter S592-2TM — 25 mm shank, internal coolant (for R390 11T3 indexable inserts) by Teknik Makina Shank milling cutter S592-2TM designed for medium-duty milling operations where coolant-through capability and reliable insert clamping reduce downtime and support consistent surface quality 25 mm shank for high rigidity Internal coolant through body Compatible with R390 11T3 inserts Secure Torx clamping M2.5x7 Faster chip evacuation and longer insert life The combination of internal coolant and a compact cutting zone helps to evacuate chips effectively and control cutting temperatures. Coolant supplied through the tool body reaches the insert pocket directly, reducing thermal loading at the cutting edge and promoting longer insert life. For production environments this translates into fewer indexings per shift and a steadier process window, supporting predictable cycle times and lower tooling costs. Increased stability for improved surface quality A straight 25 mm shank and a 120 mm overall length create a balanced tool geometry that reduces vibration under moderate overhangs. The 45 mm cutting length focuses the cutting action where it is needed, improving stability during shoulder and slot milling tasks. This structural rigidity contributes to consistent part finish and dimensional accuracy, which is especially relevant when repeatability is required across multiple workpieces. Secure clamping and quick insert replacement The cutter accepts R390 11T3 indexable inserts and uses a M2.5x7 Torx screw with a T8 key for secure retention. The proven clamping geometry ensures repeatable seat positioning and safe torque values, while indexable inserts allow rapid edge changes without full tool replacement. These characteristics reduce non-productive time and simplify tool management in busy workshops that rely on predictable maintenance intervals. Practical fit for modular machining systems With its standard interface and compatibility with widely used insert types from Sandvik, this shank milling cutter integrates easily into established tooling systems. The tool’s net weight and compact proportions facilitate handling and tool change operations at the machine, while the internal coolant option supports applications where flushing the cut zone is a priority. The result is a pragmatic tool choice for operations that value uptime and straightforward logistics. Contact Metav Werkzeuge for specification matching and procurement of this Teknik Cutting Tools shank milling cutter S592-2TM; our specialists in Emmerich advise on setup, clamping and insert choice to ensure optimal results Technical data Article number: S592-2TM Type: Shank milling cutter Brand: Teknik Makina Compatible inserts: R390 11T3 (Sandvik) Internal coolant: Yes Torx screw: M2.5x7 Torx key: T8 Core specifications Diameter: 25 mm Shank diameter: 25 mm Overall length: 120 mm Cutting length (shank): 45 mm Number of cutting edges: 3 Weight: 0.446 kg Features Indexable insert system Coolant-through tool body Secure Torx clamping Suitable for modular toolholders FAQ Is this cutter compatible with Sandvik inserts? The S592-2TM accepts R390 11T3 indexable inserts, which are available from Sandvik and match the cutter’s pocket geometry. Does the tool provide through-coolant capability? Yes, the cutter features internal coolant through the body, delivering coolant directly to the insert seat. What is the required Torx key and screw for insert clamping? Insert clamping uses a M2.5x7 Torx screw tightened with a T8 key for secure and repeatable retention. What are the main dimensions to consider for tool setup? Key setup values: 25 mm diameter, 120 mm overall length, and 45 mm cutting length — useful for determining overhang and holder compatibility. How many cutting edges does the cutter have? The cutter is configured with 3 cutting edges, which balances material removal rate and insert economy. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
25mm End Mill For R390-11T3 Indexable Inserts 3 Flutes, 50mm Cutting Length - Teknik Makina
Take advantage of fast set-up and stable cutting performance thanks to the combination of a 25 mm shank, compatibility with R390‑11T3 indexable inserts and a robust three‑edge geometry; order directly via Metav Werkzeuge or consult our specialists for application advice. Insert milling cutter S597TM by Teknik Makina — 25 mm shank, for R390‑11T3 indexable inserts The insert milling cutter S597TM is designed to accept R390‑11T3 indexable inserts and to deliver reliable face and peripheral milling performance in industrial CNC environments. 25 mm shank diameter For R390‑11T3 indexable inserts Three cutting edges for stable machining 90° cutting angle for square shoulder milling Precision compatibility reduces set‑up time and errors The S597TM insert milling cutter is engineered around a standard R390‑11T3 pocket, which means quick, repeatable insert seating and minimal set‑up complexity. The 25 mm shank fits common tool holders, while the secure Torx M2.5x7 clamping screw (Torx key T8) ensures positive insert retention. By standardising on widely available indexable inserts, tool changeover becomes faster and spares management simpler, helping production planners reduce downtime and maintain process stability. Stable cutting geometry for consistent surface quality With three cutting edges and a 90° cutting angle, the tool offers good load distribution across the insert radius, which stabilises cutting forces during face milling and square‑shoulder operations. The 50 mm cutting length and 200 mm overall length balance reach and rigidity, enabling reliable material removal while limiting vibration. For machinists, this translates into repeatable part geometry and fewer secondary operations to correct surface finish or dimensional variance. Practical handling and serviceability for the workshop The tool body is supplied ready for insert installation using the specified Torx M2.5x7 screw and T8 key, simplifying maintenance routines on the shop floor. The standardised insert interface and common screw type mean cutters can be serviced with minimal special tooling, reducing the need for bespoke spare parts. The clear mechanical design supports quick inspection and predictable reassembly, which is valuable for production teams aiming for deterministic changeover times. Suited workflows and typical applications Designed as an indexable insert milling cutter, the component is primarily intended for use in milling centres and CNC machining operations where modular tooling and fast insert replacement are priorities. Its geometry favours face milling and shoulder work where a square cut is required. Compatibility with Sandvik R390‑11T3 inserts provides access to a wide range of grades and chipbreakers, enabling selection for specific workpiece materials and cutting conditions while keeping tool stock consolidated. Consult Metav Werkzeuge for tailored selection, availability and application guidance on the Teknik Makina S597TM insert milling cutter; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: S597TM Brand: Teknik Makina Designation: Insert milling cutter for R390‑11T3 indexable inserts Torx screw: M2.5x7 Torx key: T8 Facts Shank diameter: 25 mm Cutting length: 50 mm Overall length: 200 mm Diameter: 25 mm Cutting edges: 3 Cutting angle: 90° Weight: 0.762 kg Special features Compatible inserts: R390‑11T3 Compatible insert manufacturer: Sandvik Suitable for modular indexable tooling systems Secure Torx clamping for quick insert changes FAQ Which inserts fit this cutter? The S597TM insert milling cutter is designed for R390‑11T3 indexable inserts; Sandvik R390‑11T3 grades are directly compatible. What shank diameter is required for tool holders? The tool has a 25 mm shank and is intended for holders that accept a 25 mm diameter shank. How many cutting edges does the tool have and what is the cutting angle? The cutter features three cutting edges and a 90° cutting angle, optimised for square‑shoulder and face milling. Which fastening parts are supplied for insert clamping? Insert retention uses a Torx M2.5x7 screw; the specified key is a T8 Torx. What is the overall length and cutting length of the tool? The tool measures 200 mm overall length with a 50 mm cutting length, balancing reach and rigidity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For R390-11T3 Indexable Inserts, 90° Cutting Angle, 3 Flutes, 60mm Cutting Length - Teknik Makina
Take advantage of a durable milling solution that combines Sandvik R390-11T3 insert compatibility, a 25 mm shank and a generous 60 mm cutting length for stable, repeatable shoulder and face milling. Benefit from a three‑edge geometry that improves surface finish while maintaining efficient material removal—order directly via Metav Werkzeuge or consult our specialists for application advice. Shaft cutter S598TM – Indexable-insert milling arbor with 25 mm shank and 60 mm cutting length by Teknik Makina Shaft cutter S598TM for reliable milling with R390-11T3 indexable inserts, designed for heavy-duty shoulder and face operations in production environments Compatible with R390-11T3 Sandvik indexable inserts 25 mm shank for standard toolholders Three cutting edges for smooth material removal 60 mm cutting length for deep shoulder milling Consistent accuracy through proven insert compatibility The shaft-mounted cutter is engineered for repeatable performance when used with R390-11T3 indexable inserts. The combination of a 25 mm shank and a solid arbor design delivers reduced vibration and stable cutting forces, which directly benefits process reliability and component quality. The tool’s three cutting edges support balanced load distribution, translating into a finer surface finish and longer insert life compared with single-edge alternatives. Where tool change frequency and scrap reduction matter, this configuration offers a measurable productivity advantage. Faster set-ups and secure clamping reduce downtime A short changeover time is enabled by the straightforward clamping concept: inserts are secured with a Torx M2.5x7 screw tightened with a T8 key, ensuring quick and secure replacement. The 90° cutting angle presents a familiar geometry for standard shoulder milling, making machining parameters easier to transfer between setups. This pragmatic design reduces non-productive time and simplifies operator training, supporting lean production goals without complex intervention. Robust design for demanding milling tasks Engineered as a milling arbor for indexable-insert applications, this tool supports a range of face and shoulder operations where a solid shank and extended cutting length are required. The 60 mm cutting length provides capability for deeper shoulders while the overall length and 25 mm diameter maintain compatibility with common toolposts and holders. Compatibility with Sandvik inserts means access to a broad portfolio of grades and chipbreakers for varied materials, enabling informed selection for productivity or finish-focused strategies. Serviceability and inventory advantages Maintenance is straightforward: replacement inserts and the Torx M2.5x7 fastening allow rapid field service without special equipment beyond the specified T8 key. The arbor’s weight of 0.951 kg makes handling predictable during tool changes and stocking. For workshops consolidating tooling ranges, this arbor reduces the complexity of spare parts and insert types when paired with the widely available R390-11T3 family. Clear identification by SKU S598TM aids inventory management and reordering. For application advice tailored to the S598TM and to secure prompt delivery from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for expert assistance and reliable supply. Technical data Article number: S598TM Manufacturer: Teknik Makina Brand: Teknik Makina Material / execution: Shaft-mounted milling arbor Core specifications Shaft diameter: 25 mm Cutting length: 60 mm Overall length: 250 mm Cutting edges: 3 Diameter: 25 mm Weight: 0.951 kg Cutting angle: 90° Features & compatibility For R390-11T3 indexable inserts Compatible with Sandvik insert family Torx screw M2.5x7 for insert clamping Torx key size T8 for assembly/disassembly eCl@ss: 21180806 ETIM: EC011860 FAQ What inserts are compatible with this cutter? The shaft cutter S598TM is designed for R390-11T3 indexable inserts and is compatible with the Sandvik range of R390‑series inserts. What shank diameter is required for mounting? The tool has a 25 mm shank, so a matching collet or toolholder with a 25 mm bore is required for secure mounting. How many cutting edges does the arbor provide? This milling arbor features three cutting edges, offering balanced cutting action and improved surface finish for shoulder milling. Which screw and key are used for securing the inserts? Inserts are fastened with a Torx M2.5x7 screw; the specified tightening key is T8. Is the cutter suitable for deep shoulder milling? Yes. The 60 mm cutting length makes this arbor well suited to deeper shoulder and face milling operations within its shank and holder limits. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill For R390-1806 Indexable Inserts, 2 Flutes 60mm Cutting Length, 90° Cutting Angle - Teknik Makina
Benefit from a robust combination of a 25 mm shank, a 60 mm effective cutting length and compatibility with R390‑1806 indexable inserts to ensure stable, repeatable milling cycles; order the S600TM via Metav Werkzeuge or consult our specialists for application support. S600TM shaft cutter for R390‑1806 indexable inserts by Teknik Makina — 25 mm shank, 60 mm cutting length S600TM is a shaft cutter engineered for indexable‑insert milling with R390‑1806 inserts, designed for reliable face milling and slotting in production and workshop environments 25 mm shank diameter 60 mm effective cutting length Compatible with R390‑1806 inserts Secured with M4x11 Torx screw (T15) Proven milling performance for consistent cycle times The cutter is built to deliver stable machining through its 25 mm shank and firm clamping design, reducing runout and vibration during operations. The combination of a robust shank and a balanced 200 mm overall length provides predictable tool behaviour, which translates into repeatable part quality and fewer cycle interruptions. With a 90° cutting angle and two cutting edges, the tool is optimised for efficient material removal where planar faces and slots are required; this means shorter machining cycles and less time spent on secondary finishing. Clear compatibility and straightforward setup Compatibility with R390‑1806 indexable inserts (Sandvik format) simplifies tooling selection and supply chain logistics. The cutter is fastened using an M4x11 Torx screw and requires a T15 Torx key for secure insert clamping, enabling quick insert changes and minimal downtime. For technicians new to indexable‑insert systems: an indexable cutter holds replaceable carbide inserts in a seat, so worn cutting edges are renewed by replacing the insert rather than the whole cutter — a cost‑effective approach for high‑volume production. Operational advantages that reduce process risk A 60 mm cutting length gives a practical reach for many face milling and slotting tasks without compromising stiffness; combined with a nominal diameter of 25 mm and a net weight of 0.756 kg, the tool balances rigidity with manageable handling. These attributes support safer, more stable cutting conditions that extend insert life and reduce scrap rates. The straightforward geometry and proven insert standard also aid inventory management, since familiar R390‑1806 inserts from Sandvik are widely available and easy to stock. Support, sourcing and workshop integration Sourcing from a reliable supply partner reduces procurement complexity. Metav Werkzeuge’s Emmerich site acts as a quality filter for the European market, offering a broad portfolio and dependable logistics. For operational planning, note the cutter’s measured parameters — shank diameter, cutting length, overall length and fastening type — when specifying holders or checking machine‑spindle compatibility. For bespoke advice on fixturing, balancing or recommended cutting parameters, Metav’s consultancy provides quick technical guidance tailored to production requirements. Contact Metav Werkzeuge for tailored advice on the S600TM and to arrange supply from Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S600TM Manufacturer: Teknik Makina Product name: Schaftfräser (shaft cutter) for R390‑1806 indexable inserts Facts Shank diameter: 25 mm Effective cutting length: 60 mm Diameter: 25 mm Number of cutting edges: 2 Overall length: 200 mm Cutting angle: 90° Fastening screw: M4x11 Torx Torx key: T15 Weight: 0.756 kg Special features Compatible with R390‑1806 indexable inserts Suitable insert manufacturer: Sandvik Secured by M4x11 Torx screw (T15) Two cutting edges for efficient material removal Designed for face milling and slotting applications FAQ What inserts are required for this cutter? The S600TM accepts R390‑1806 indexable inserts; Sandvik‑specification inserts are compatible. Which toolholding size is required for safe mounting? Use a holder that accepts a 25 mm shank diameter and provides proper axial and radial clamping for the 200 mm overall length. How is the insert fixed and changed? Inserts are clamped with an M4x11 Torx screw; a T15 Torx key is used for insertion and removal. Is the cutter suitable for deep slotting operations? The 60 mm effective cutting length offers reach for many slotting tasks, but application limits depend on machine rigidity and cutting parameters. How does the cutter contribute to operational efficiency? Replaceable inserts reduce tool replacement time and cost, while the solid shank and balanced geometry promote consistent part quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for RPMT 0803 Indexable Inserts With Internal Coolant, 250mm - Teknik Makina
Combine robust compatibility with RPMT 0803 inserts, internal coolant delivery and a long 250 mm body to ensure consistent chip evacuation and reduced downtime; order or request advice through Metav Werkzeuge for a tailored supply solution. R314TM — 25 mm shank milling cutter for RPMT 0803 indexable inserts by Teknik Makina The R314TM is a precision-engineered indexable milling cutter, designed for heavy-duty face and slot milling using RPMT 0803 inserts and delivering coolant directly to the cutting zone. Internal coolant for improved tool life Compatible with RPMT 0803 inserts by Korloy 25 mm shank, 250 mm overall length Minimise downtime with targeted coolant and reliable chip control The core benefit of an integrated coolant channel is consistent cooling and efficient chip evacuation. The built-in internal coolant directs lubricant and coolant precisely to the insert pockets, which reduces thermal load and helps prevent edge build-up during prolonged cuts. This targeted supply improves wear behaviour and contributes to longer service intervals for the holder and the inserts. For production environments where process stability is essential, this results in fewer tool changes and a more predictable machining cycle. Sturdy design for repeatable, high-accuracy milling A robust 25 mm shank and a total length of 250 mm provide a balance between reach and rigidity, enabling stable milling in both slotting and light shoulder operations. The tool features 4 cutting edges, allowing balanced material removal and smoother engagement with the workpiece. The cutter head accepts standard RPMT 0803 indexable inserts, making replacement straightforward and cost-effective; insert clamping uses an M3x7 Torx screw with a T8 key for secure seating and easy service. This mechanical setup ensures consistent seat location and repeatability across insert changes. System compatibility and straightforward maintenance for shop use Compatibility with Korloy RPMT 0803 inserts broadens the selection of grades and chipform options, simplifying tool inventory management. The body is purpose-built to accept conventional triangular inserts and fasten them reliably, while the internal coolant passage promotes cleaner chip flow and reduced heat at the cutting edge. Routine maintenance consists of replacing worn inserts and checking the Torx mounting screw; the standardised fastener format and accessible design speed up service operations and lower total processing cost over time. Request a technical consultation or a tailored quotation from Metav Werkzeuge for the Teknik Makina R314TM shank milling cutter with internal coolant; Metav Werkzeuge can advise on insert grades, hold stock and supply directly from Emmerich Technical Data Article number: R314TM Manufacturer: Teknik Makina Product type: Indexable shank milling cutter Facts Diameter: 25 mm Overall length: 250 mm Cutting length: 40 mm Number of cutting edges: 4 Shank diameter: 25 mm SKU: R314TM Special features Internal coolant For RPMT 0803 indexable inserts Compatible with Korloy inserts Torx screw M3x7 Torx key T8 FAQ What insert type does this cutter accept? The cutter accepts RPMT 0803 indexable inserts; the body is machined to seat these inserts accurately for repeatable performance. Is there coolant delivery through the tool? Yes, the holder features internal coolant that supplies fluid directly to the insert pockets to improve chip evacuation and edge life. Which insert manufacturers are compatible? The tool is compatible with Korloy RPMT 0803 inserts, widening available grades and chip control options. What fastening hardware is used for the inserts? Inserts are secured with an M3x7 Torx screw; the required Torx key is T8, ensuring a secure and serviceable clamping method. How does the 25 mm shank affect machining stability? A 25 mm shank offers a stable connection to the toolholder, balancing rigidity and accessibility for many shop applications and reducing vibration for improved surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for Sandvik R390-11T3 inserts - Teknik Makina
Product Technical Specifications: Order Number: S595TM Item: End Mill usable with R390-11T3 Indexable Inserts of Sandvik Brand: Teknik Makina Quantitative Characteristics: Diameter: 25mm Cutting Edges: 3 Weight: 0.557kg Total length: 150mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com
25mm End Mill For SPMG 0904 Indexable Inserts, 2 Flutes 50mm Cutting Length, 150mm Overall Length - Teknik Makina
Take advantage of the robust combination of secure Torx clamping, long cutting length and precise 25 mm shank for consistent machining results; order directly via Metav Werkzeuge or contact our consultants for integration advice. Shank milling cutter S828TM — 25 mm shank, for SPMG 0502–0904 indexable inserts (Teknik Makina) The Shank milling cutter S828TM is a compact, indexable-insert milling body engineered for stable milling operations with SPMG 0502–0904 inserts, designed to fit standard toolholders and deliver dependable performance in series production. Solid 25 mm shank diameter 50 mm cutting length for deep cuts Compatible with SPMG 0904 indexable inserts Secure Torx clamping with M3.5x8.5 screw Enhanced rigidity and runout control for reliable milling This milling body features a 25 mm shank and a 150 mm overall length, providing a solid connection to the machine spindle and reduced deflection under load. The combination of a sturdy shank and compact geometry supports consistent tool life and repeatable machining accuracy, which is essential for production runs where stability matters. The modest mass (approx. 0.567 kg) contributes to predictable dynamic behaviour and easier balancing in multi-tool setups. High material removal with controlled chip handling With a 50 mm cutting length and 2 cutting edges, the design balances efficient material removal and controlled chip flow. The indexable-insert concept allows for rapid insert changes and predictable cost-per-edge, improving machine uptime. The tool body accepts the common SPMG 0904 insert format, enabling straightforward integration into existing insert inventories and reducing tooling complexity on the shop floor. Secure clamping and quick maintenance procedures Clamping is achieved with a Torx clamping screw M3.5x8.5 and requires a T15 key, which ensures firm insert retention during heavy cuts while allowing swift replacement when required. The Torx interface reduces the risk of cam-out and provides consistent clamp torque with standard workshop tools. The insert seat geometry is designed for repeatable positioning so that index changes restore cutting geometry without additional set-up time. Compatibility and process integration for production environments The tool body is specified for use with Taegutec-manufactured indexable inserts and matches common industrial setups expecting SPMG 0502–0904 insert sizes. Its straightforward mechanical interface makes it suitable as a replacement or upgrade in existing tool sets, aiding standardisation across the tool crib. The result is a tool that supports lean tooling management and predictable production output. For procurement and technical advice on integrating the S828TM shank milling cutter into existing machining processes, contact Metav Werkzeuge for local supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored support and delivery options. Technical data Article number: S828TM Manufacturer: Teknik Makina Product type: Shank milling cutter Core dimensions Shank diameter: 25 mm Cutting length: 50 mm Diameter: 25 mm Number of cutting edges: 2 Overall length: 150 mm Weight: 0.567 kg Features Compatible with SPMG 0904 indexable inserts For SPMG 0502–0904 indexable inserts Torx clamping screw M3.5x8.5 Torx key size T15 Suitable for Taegutec inserts FAQ Which insert sizes fit this milling body? The S828TM accepts SPMG 0502–0904 indexable inserts and is specified to work with SPMG 0904 sizes as listed. What clamping hardware is required for insert changes? Insert retention uses a Torx clamping screw M3.5x8.5; a T15 Torx key is required for secure tightening and removal. How many cutting edges does the tool have? The tool body is configured for 2 cutting edges, enabling straightforward chip control and efficient material removal. What are the main dimensions to consider when fitting into a toolholder? Key dimensions are a 25 mm shank diameter, 150 mm overall length and a 50 mm cutting length; these determine holder compatibility and projection. Is the tool compatible with Taegutec inserts? Yes, the milling body is noted as suitable for Taegutec-manufactured indexable inserts in the SPMG family. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for TNKT 1105 Indexable Inserts with Internal Coolant, 120mm Overall Length - Teknik Makina
Take advantage of the combination of precision insert compatibility, robust shank stability and integrated internal coolant for consistent machining cycles; order directly via Metav Werkzeuge or consult our specialists for application advice. Shank Milling Cutter for TNKT 1105 Indexable Inserts — 25 mm, internal coolant (Teknik Makina) The Shank Milling Cutter for TNKT 1105 Indexable Inserts is an indexable-insert milling tool designed for efficient face and slot milling in CNC operations, offering internal coolant and a rigid shank for stable cutting performance. 25 mm cutter diameter Internal coolant for reliable cooling Compatible with TNKT 1105 Korloy inserts 23 mm shank, 120 mm overall length Maximised cycle time and consistent chip control With a 25 mm cutting diameter and 3 cutting edges, this indexable-insert milling solution delivers predictable material removal rates while reducing tool-change frequency. The internal coolant channel feeds cooling fluid directly to the cutting zone, improving chip evacuation and reducing thermal loading on the insert seats. For production environments where throughput and repeatability matter, the combined effect of a compact cutter body and targeted cooling helps maintain surface finish and dimensional stability across long runs. Secure clamping and simplified insert changes The tool features a precise interface and a 23 mm shank that provides stiffness in the holder, minimising vibration during interrupted cuts. Insert retention uses a Torx fixation (Torx key T8) with M3x7 screws, enabling fast and reliable insert replacement with standard workshop tooling. This arrangement reduces downtime for maintenance and keeps set-up times predictable, which supports higher machine availability and streamlined tool management in busy shops. Broad indexable-insert system compatibility Designed for the widely used TNKT 1105 insert family and compatible with Korloy inserts, the cutter permits flexible grade selection and cost-effective insert rotation strategies. Using an indexable system allows the separation of cutting geometry from the body, so the cutter body remains in service while inserts are replaced as they wear. This approach is economically efficient for mixed production, where different grades and coatings can be chosen to match specific workpiece materials without changing the holder. Practical workshop benefits and assurance of supply Weighing 0.372 kg and measuring 120 mm in overall length with a 35 mm cutting length on the shank, the cutter balances accessibility in tight setups with sufficient reach for common milling tasks. The design supports routine maintenance and inventory control: a compact SKU strategy using the S056TM identifier simplifies reordering. Metav’s Emmerich hub acts as a quality filter for the European market, ensuring steady availability and technical support to keep production moving. Contact Metav Werkzeuge for an application review and parts allocation; our consultants will advise on insert grades and machine parameters to suit specific milling tasks. Technical data Article number: S056TM Product type: Shank milling cutter Manufacturer: Teknik Makina Internal coolant: yes Facts Cutter diameter: 25 mm Overall length: 120 mm Shank diameter: 23 mm Cutting length (shank): 35 mm Number of cutting edges: 3 Weight: 0.372 kg Torque key: T8 Screw: M3x7 Special features Compatible with TNKT 1105 indexable inserts Suitable for Korloy TNKT 1105 inserts Indexable-insert system Label: 25mm Shank Cutter TNKT 1105 L120mm with internal coolant FAQ Which inserts fit this cutter? The cutter accepts TNKT 1105 indexable inserts; Korloy TNKT 1105 grades are compatible and commonly used with this cutter to match material and cutting conditions. How is coolant supplied to the cutting zone? Coolant is fed through the body via the integrated internal coolant channel, delivering fluid directly to the insert zone for improved chip control and tool life. What fastening hardware is required for insert changes? Insert retention uses M3x7 Torx screws operated with a T8 Torx key, allowing rapid and secure insert replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for VDKT 11T2 Indexable Inserts Internal Coolant, 3 Flutes, 115mm Overall Length - Teknik Makina
Reliable performance with efficient chip evacuation and secure clamping makes this cutter a practical choice for modern milling tasks; the internal coolant and 25 mm shank combine to reduce downtime and extend insert life. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Indexable shank milling cutter S400TM — 25 mm shank, internal coolant (Teknik Makina) The Indexable shank milling cutter S400TM is a purpose-built tool for precision milling with VDKT 11T2 indexable inserts, offering secure shank fixation and directed coolant for production and workshop environments. 25 mm shank for rigid clamping Internal coolant for improved chip evacuation Compatible with VDKT 11T2 Korloy inserts Three cutting edges for smooth material removal Stable clamping and reduced vibration for consistent surface quality The solid 25 mm shank and compact overall geometry deliver high stiffness at the toolholder, which translates into reduced chatter and more consistent surface finishes during heavy or interrupted cuts. With three cutting edges, the design balances material removal rate and vibration damping so that cycle times remain competitive while maintaining target tolerances. This structural stability benefits both single-shift workshops and continuous production lines by lowering scrap rates and reducing rework. Directed coolant flow for longer insert life and cleaner chips The integrated internal coolant channels supply cutting fluid close to the cutting zone, improving cooling and lubrication where it matters most. As a result, chip evacuation is more efficient and thermal load on the cutting edges is reduced, which helps preserve insert geometry and extend service intervals. When combined with VDKT 11T2 indexable inserts from Korloy, the coolant-assisted setup supports stable tool life and predictable tool-change planning, contributing to a lower cost per component over longer production runs. Fast, secure insert fastening for minimal downtime Insert retention is handled with a Torx T8 interface and M2.5x5.5 screw, enabling quick and reliable insert changes with standard workshop tools. The simple fastening system reduces changeover time and minimises the risk of incorrect torque application, protecting insert seats and preserving repeatability. The tool’s practical design supports efficient maintenance routines and clear spare-part handling in busy production settings. Compact reach with practical cutting length for common milling tasks With an overall length of 115 mm and a cutting length of 35 mm, the tool offers a useful combination of reach and rigidity for slotting, facing and light shoulder milling operations that use indexable cutting edges. The compact proportions help keep overhang low, improving stability in deeper pockets or when working close to fixtures. The cutter’s balanced specification makes it an adaptable choice for a wide range of indexable-insert milling applications without unnecessary complexity. Choose Teknik Makina’s S400TM when internal coolant and rigid shank performance are priorities; contact Metav Werkzeuge in Emmerich for tailored supply options and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S400TM Manufacturer: Teknik Makina Product type: Shank milling cutter Insert type: VDKT 11T2 Compatible insert manufacturer: Korloy Facts Shank diameter: 25 mm Overall length: 115 mm Cutting length: 35 mm Number of cutting edges: 3 Weight: 0.392 kg Torx key: T8 Torx screw: M2.5x5.5 Special features Internal coolant Designed for indexable insert milling Quick-change insert fastening SKU: S400TM FAQ Which inserts are suitable for this cutter? The S400TM is designed for VDKT 11T2 indexable inserts and is compatible with Korloy-manufactured VDKT 11T2 grades. Does the tool provide internal coolant supply? Yes — the cutter features internal coolant channels to direct fluid to the cutting zone for improved cooling and chip control. What are the key dimensions to consider for setup? Important dimensions are a 25 mm shank diameter, 115 mm overall length and 35 mm cutting length, which should be matched to the machine’s toolholder and reach requirements. How are the inserts secured? Inserts are fastened using a Torx T8 drive and M2.5x5.5 screw for secure, repeatable clamping and straightforward changeovers. Is the S400TM suitable for high-feed milling? The cutter’s rigid 25 mm shank and three-edge configuration support robust material removal rates within the operational limits of VDKT 11T2 inserts, making it suitable for many high-feed scenarios where insert selection and machining parameters are correctly matched. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
25mm End Mill for XEKT 1904 Indexable Inserts Internal Coolant, 2-Flute, 61mm Cutting Length - Teknik Makina
The combination of a 25 mm shank, internal coolant and compatibility with XEKT 1904 indexable inserts delivers consistent tool life and dependable chip control for industrial milling; order the tool directly via Metav Werkzeuge or consult the technical team for application advice. Shank milling cutter S386TM – 25 mm shank, internal coolant (Teknik Makina) A shank milling cutter S386TM designed for XEKT 1904 indexable inserts, offering internal coolant and a 200 mm overall length for reliable industrial milling applications 25 mm shank diameter Internal coolant for chip control Compatible with XEKT 1904 inserts Secure Torx clamping system Predictable productivity with durable cutting geometry The indexable milling body offers a stable platform for repeatable machining cycles, combining a 25 mm shank with a 200 mm overall length and a 61 mm cutting length that balance reach and stiffness. With two cutting edges, the design reduces unnecessary mass while maintaining effective chip evacuation; this results in consistent surface quality and predictable tool-change intervals. The tool body is engineered to accept XEKT 1904 inserts, which enables fast insert replacement and lowers per-cut costs without sacrificing repeatability. Controlled temperatures and secure insert clamping Internal coolant is routed directly to the cutting zone to support heat dissipation and chip removal; the internal coolant feed improves insert life by maintaining stable cutting temperatures and reducing edge wear. The clamping system uses a T15 Torx key and M4x8.5 Torx screw for positive retention, ensuring the insert seat remains secure under heavy machining loads. The combination of coolant delivery and robust fastening reduces the risk of built-up edge and enhances process reliability across continuous production runs. Compatibility that simplifies workshop logistics Designed for use with XEKT 1904 indexable inserts from Korloy, this milling body integrates into existing tooling families with minimal adjustment. The indexable design allows workshops to replace only the insert rather than the entire tool, supporting a lower lifetime cost of ownership and faster downtime recovery. At a weight of 0.627 kg the tool balances handling convenience with industrial robustness. For application-specific recommendations or to confirm geometry clearance in a particular machine set-up, Metav Werkzeuge’s technical advisors are available to assist. Contact Metav Werkzeuge in Emmerich for tailored application guidance or to request a supply proposal for the Teknik Cutting Tools S386TM indexable milling cutter with internal coolant. Technical data Article number: S386TM SKU: S386TM Product type: Indexable milling cutter ECLASS: 21180806 Dimensions & weight Diameter: 25 mm Overall length: 200 mm Cutting length (shank): 61 mm Shank diameter: 25 mm Weight: 0.627 kg Cutting edges: 2 Features & compatibility Internal coolant: yes Compatible inserts: XEKT 1904 Compatible insert manufacturer: Korloy Torx key: T15 Torx screw: M4x8.5 Manufacturer (raw data): Teknik Makina Label: 25mm Shank milling cutter XEKT 1904 L200mm with internal coolant FAQ Which inserts fit the tool? The shank milling cutter S386TM is specified for XEKT 1904 indexable inserts and accepts inserts from Korloy as listed in the product data. Does the tool provide internal coolant? Yes, the S386TM features internal coolant routed to the cutting zone to aid chip evacuation and temperature control. What are the key dimensions to check for machine setup? Key dimensions are a 25 mm shank, 200 mm overall length and 61 mm cutting length, which are relevant when confirming holder clearance and reach. How is the insert secured? Insert retention on the S386TM is via a Torx screw system using a T15 key and M4x8.5 screw for secure clamping. How many cutting edges does the tool have? The milling body is supplied with 2 cutting edges, offering a balance between material removal rate and chip space. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak No:9, Selcuklu/KONYA, TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
High-performance shank cutters and ball nose cutters for efficient milling
Insert shank cutters and ball nose cutters combine flexibility and productivity for a wide range of milling tasks. The category covers steel-bodied shank cutters fitted with indexable inserts for economical roughing, face milling, cornering and slotting, as well as ball nose cutters for contouring and 3D finishing.
How these tools work and where they belong
Shank cutters with indexable inserts use a carrier body made from hardened steel; the cutting edges are provided by removable inserts rather than a solid tool blank. Where tools do not have internal coolant, process heat and chips are managed via external coolant nozzles or compressed air, which is sufficient for open, surface-level and easily accessible milling on standard materials. Shank cutters with internal coolant feature fine internal channels that deliver coolant or blasting air directly to each cutting edge under pressure. This targeted supply is essential for deep pockets, cavities, full slotting and machining of heat-resistant or difficult-to-machine materials, because it prevents chip re-cutting, protects cutting edges from thermal overload and enables higher feed rates and improved surface quality.
Cut cycle times and reduce tooling costs
- Replaceable indexable inserts reduce consumable costs and shorten tool change time.
- Targeted internal coolant improves chip evacuation and extends insert life.
- Robust steel carrier bodies enable heavy-duty roughing without frequent tool replacement.
- Suitable for roughing, planing, corner milling and slot milling as well as precision 3D profiling with ball nose cutters.
A practical choice for purchasing and stocking tools
Metav brings a pragmatic purchasing advantage: a broad range of milling solutions is available from a single European quality hub. Metav’s focus on democratising precision means workshops benefit from a wide assortment, consistent quality control from Emmerich and steady supply — supported by decades of expertise and over 48,000 satisfied customers. Choose Metav for a centralised sourcing strategy that reduces supplier complexity while keeping access to both insert milling cutters (also referred to as insert milling cutters or indexable end mills) and ball nose cutters (also known as ball nose end mills or radius cutters) straightforward.
Quick summary
Insert shank cutters and ball nose cutters deliver flexible, cost-effective milling: replaceable inserts lower running costs, and internal coolant options enable higher performance and longer tool life where chip control is critical.
FAQ
When should I choose a shank cutter with indexable inserts rather than a solid carbide end mill?
Choose shank cutters with indexable inserts for economical roughing and high-stock-removal tasks where replacing inserts is preferable to replacing an entire tool; they are especially effective for face milling, cornering and slotting operations.
Does internal coolant make a measurable difference for ball nose cutters?
Yes. Internal coolant directed to each cutting edge reduces chip re-cutting and thermal stress, which improves surface finish and increases insert life when machining deep pockets, cavities or heat-resistant materials.
Can shank cutters without internal coolant be used for general workshop milling?
Absolutely. Tools without internal coolant rely on external coolant nozzles or compressed air and are well suited to open, superficial and easily accessible milling on standard materials.
What milling operations are shank cutters for indexable inserts typically used for?
Shank cutters with indexable inserts excel at economical roughing, planfräsen (face milling), corner milling and slot milling; ball nose cutters are the preferred choice for 3D profiling and finishing operations.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com