Efficient shaft cutters and ball nose cutters for versatile milling
Shaft cutters and ball nose cutters serve as robust rotating tools for roughing, face milling, corner milling and slotting, offering economical replacement of indexable inserts rather than whole solid tools. Available in versions with internal coolant to feed lubricant directly to each cutting edge or without internal coolant relying on external nozzles, these cutters ensure effective chip evacuation and thermal control suited to standard materials or deep pocket and cavity work. By preventing chip re-cutting and protecting cutting edges, they deliver higher feed rates, improved surface finish and extended tool life in demanding metalworking applications.
30mm Solid Carbide Shank Cutter For RDMT 1003 Indexable Inserts, 3 Flutes 40mm Cutting Length, 25mm Shank - Teknik Makina
Take advantage of a robust combination of compatibility, secure clamping and efficient cutting: the tool accepts RDMT 1003 indexable inserts, offers a 30 mm cutting diameter with three cutting edges and a rigid 25 mm shank for reduced vibration. Order the shank milling cutter directly via Metav Werkzeuge or ask the consultants for tailored application advice. Shank milling cutter R213TM – 30 mm Ø, three cutting edges (Teknik Makina) The Shank milling cutter R213TM is a purpose-built tool for indexable-insert milling with RDMT 1003 inserts, designed to deliver steady material removal in general workshop and light industrial applications. 30 mm cutting diameter Three cutting edges for smooth milling 25 mm shank for secure clamping Compatible with RDMT 1003 inserts Faster, more consistent material removal for routine milling The combination of a 30 mm diameter and three cutting edges is focused on delivering a reliable metal-removal rate while maintaining a consistent surface finish. The cutter’s 40 mm cutting length provides adequate engagement for many slotting and face-milling tasks without excessive overhang, which helps to keep vibration and runout low. For practical selection, the tool accepts standard RDMT 1003 indexable inserts, enabling predictable tool-life planning and straightforward insert changes. This configuration is intended to reduce cycle times and improve process stability in repetitive production runs. Rigid design that maintains precision under load A 25 mm shank and a 200 mm overall length give the assembly a balance between reach and rigidity, which matters when repeatability and dimensional accuracy are required. The clamping system uses an M3.5 locking screw and a M3.5×8.5 Torx screw, tightened with a T15 key, ensuring secure insert retention and minimised micro-movement at the cutting edge. Reduced tool chatter translates into better surface quality and less wear on inserts, so downtimes for regrinding or replacement are less frequent. The tool’s mass (approx. 0.789 kg) contributes to stable cutting dynamics in many bench and shop-floor setups. Practical compatibility and workshop suitability Engineered for indexable-insert operations, the cutter is particularly suited to workshops that favour interchangeable inserts for quick servicing and cost-effective consumable management. Its acceptance of RDMT 1003 inserts aligns the tool with a wide range of insert geometries and grades, allowing selection according to workpiece material and machining strategy. The robust shank and standard fastening hardware make the cutter a sensible choice for production environments and maintenance shops that require a dependable, easy-to-service milling solution. For procurement and specification checks, Metav’s product information acts as a reliable quality filter for European workshops. Contact Metav Werkzeuge for an application review and secure the Teknik Makina R213TM shank milling cutter for reliable RDMT 1003 insert machining — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: R213TM Manufacturer: Teknik Makina Facts Cutting diameter: 30 mm Shank diameter: 25 mm Cutting length: 40 mm Overall length: 200 mm Number of cutting edges: 3 Weight: 0.789 kg Special features Compatible with RDMT 1003 indexable inserts Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 FAQ What insert type does the cutter use? The cutter is designed for RDMT 1003 indexable inserts, enabling straightforward insert replacement and flexible grade selection. Is the tool suitable for general-purpose milling? Yes, the R213TM shank milling cutter is intended for general workshop milling tasks where a 30 mm diameter and three-flute geometry provide efficient material removal. How is the insert secured in the cutter? Insert retention is achieved with an M3.5 locking screw and an M3.5×8.5 Torx screw; the Torx head is tightened using a T15 key for secure clamping of the insert. Can the cutter achieve low-vibration cutting in production use? With its 25 mm shank and balanced overall length, the R213TM is engineered to reduce vibration and support consistent cutting performance in repetitive production settings. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
30mm Solid Carbide Shell End Mill For APKT 1604 Indexable Inserts, 25mm Shank 60mm Cutting Length, 3 Flutes - Teknik Makina
Take advantage of the combination of a 30 mm diameter and a 3‑cut geometry for reliable material removal and consistent cycle times; built for indexable insert systems and supplied with a secure Torx fastening, this shank milling cutter streamlines tool changeovers—order via Metav Werkzeuge or consult the technical team for application advice. Shank milling cutter S444TM — indexable cutter, 30 mm diameter, for APKT 1604 inserts (Teknik Makina) Shank milling cutter S444TM designed for medium‑duty milling applications where fast insert changes and robust clamping are required 30 mm cutting diameter for versatile use 3‑cut geometry for balanced cutting performance Compatible with APKT 1604 indexable inserts Secure Torx clamping M4x10, T15 key Improved productivity through engineered cutter geometry The 3‑cut design of this indexable milling cutter favours steady chip formation and reduced cutting forces, which leads to more predictable tool life and shorter cycle times. Because inserts are used instead of solid teeth, reconditioning is simple: worn cutting edges are replaced in seconds, keeping spindle downtime to a minimum. The combination of a 30 mm diameter with a 60 mm cutting length provides a practical reach for pocketing and face milling tasks while maintaining rigidity for consistent surface finish quality. Built for reliable clamping and fast maintenance A Torx clamping screw (M4x10) together with the supplied T15 key ensures a firm insert seat and repeatable torque when inserting APKT 1604 indexable inserts. This fastening arrangement, which is widely adopted in the industry, reduces the risk of insert movement under load and simplifies workshop procedures. The tool’s 25 mm shank is engineered for secure chucking or collet mounting, so spindle concentricity is maintained and vibration is minimised during operation. Material compatibility and application scope Configured for APKT 1604 insert geometry and compatible with Korloy insert types, the cutter is intended for general metalworking tasks where moderate depths of cut and stable feed rates are required. Its 90° cutting angle supports square shoulder milling and effective slotting routines. While designed primarily as an insert cutter for ferrous and non‑ferrous components, final process parameters should be matched to the insert grade and machine capabilities to achieve optimum results. Practical handling and workshop benefits With an overall length of 300 mm and a balanced mass of approximately 1.168 kg, the tool is easy to handle and aligns with common tool‑management workflows. The modular nature of indexable systems means inventory is reduced: fewer complete tools are needed when multiple insert grades and geometries are stocked. Additionally, the standardised Torx fixing and common insert format simplify training and spare‑part logistics across production teams. For procurement, availability checks or application guidance on the Teknik Makina S444TM shank milling cutter—compatible with APKT 1604 indexable inserts—please contact Metav Werkzeuge in Emmerich by e‑mail or phone for fast technical advice and local supply options Technical Data Article number: S444TM Manufacturer: Teknik Makina Product: Shank milling cutter for APKT 1604 indexable inserts Brand SKU: S444TM Diameter: 30 mm Shank diameter: 25 mm Cutting length: 60 mm Overall length: 300 mm Number of cutting edges: 3 Cutting angle: 90° Weight: 1.168 kg Compatible inserts: APKT 1604 Suitable for inserts by: Korloy Torx screw: M4x10 Torx key size: T15 Tool type: Indexable insert milling cutter FAQ What insert format does the cutter accept? The cutter accepts APKT 1604 indexable inserts; compatible Korloy inserts are listed among recommended options for this tool. Which shank diameter is provided for mounting? A 25 mm shank is specified for stable clamping in collets or chucks. Is the Torx fastening included for insert mounting? The tool uses an M4x10 Torx screw and requires a T15 key for secure insert fastening. What cutting operations is the tool suited to? The S444TM is intended for face milling, shoulder milling and light slotting where a 30 mm diameter and 3‑cut geometry deliver reliable material removal. How long is the tool and what is its cutting reach? Overall length is 300 mm, with a cutting length (effective) of 60 mm, offering a practical balance between reach and stiffness. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
30mm Solid End Mill for APKT 1003 Indexable Inserts Internal Coolant 120mm L120mm - Teknik Makina
Take advantage of the combination of reliable internal coolant, a 30 mm cutting diameter and a rigid 25 mm shank for a stable, productive milling process; order the shaft cutter directly via Metav Werkzeuge or consult our specialists for application advice. Indexable Insert End Mill for APKT 1003 (30 mm, internal coolant) – Teknik Makina The Indexable Insert End Mill for APKT 1003 is a 30 mm milling cutter designed for indexable-insert machining, offering internal coolant delivery for improved tool life and use with Korloy APKT 1003 inserts. 30 mm diameter with internal coolant Compatible with APKT 1003 Korloy inserts 25 mm shank for rigid tool holding 40 mm cutting length for deeper passes Greater productivity through coolant-fed cutting The internal coolant channel delivers coolant directly to the cutting zone, reducing heat generation and improving chip evacuation. This results in longer insert life and more consistent cutting performance across batch runs. Combined with the 30 mm cutting diameter and stable geometry, the tool supports higher metal removal rates while maintaining surface quality. The coolant-fed design is particularly beneficial in interrupted cuts and semi-finishing operations where reliable cooling and chip flow matter. Practical savings with indexable inserts and easy servicing Using APKT 1003 indexable inserts allows rapid replacement of worn cutting edges without regrinding the body, reducing downtime and tooling cost. Replacement is straightforward thanks to the accessible fixing hardware (Torx T8 and screw M2,5x5,5), enabling maintenance by trained workshop staff with common tools. The insert system provides the economic advantage of renewing only the cutting edge while keeping clamping accuracy and repeatability at a professional level. Rigid clamping and stable process behaviour The 25 mm shank ensures compatibility with standard holders and collets, delivering the rigidity required for stable milling conditions. With four cutting edges and a 40 mm cutting length, the geometry balances material engagement and torque demand to minimise vibration and tool deflection. This contributes to repeatable tolerances and surface finishes, making the cutter suitable for production environments where consistency between parts is essential. Application guidance and handling recommendations The tool body, identified by SKU S170-1TM, benefits from straightforward handling and secure fastening of inserts; the combination of indexable design and internal coolant reduces thermal distortion during extended cycles. For optimal results, match the shank clamping diameter to the machine tool holder, check insert seating torque, and confirm coolant pressure and flow to exploit the full advantages of the coolant-fed system. Regular inspection of clamping screws and insert seats preserves accuracy and extends service intervals. Contact Metav Werkzeuge to discuss the Teknik Makina indexable insert end mill, confirm the best insert grade for the application, or request a tailored quote for your production needs Technical data SKU: S170-1TM Label: 30mm Schaftfräser APKT 1003 L120mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 30 mm Total length: 120 mm Shank diameter: 25 mm Cutting length (shank): 40 mm Number of cutting edges: 4 Weight: 0.487 kg Torx key: T8 Torx screw: M2,5x5,5 Internal coolant: yes Special features Compatible with APKT 1003 indexable inserts Suitable for Korloy APKT 1003 insert grades Indexable insert system for quick edge changes Rigid shank for stable toolholding Accessible fastening hardware for maintenance FAQ What inserts are compatible with this end mill? The end mill accepts APKT 1003 indexable inserts and is specified for Korloy APKT 1003 grades; matching the insert grade to the workpiece material ensures optimal performance. How is coolant supplied to the cutting edge? Coolant is delivered through the tool body via the integrated internal channel, enabling direct cooling at the cutting zone and improving insert life and chip evacuation. Which shank holders are required for stable clamping? A holder or collet that accepts a 25 mm shank and provides accurate concentric clamping is recommended to exploit the cutter’s rigidity and maintain repeatable results. How are inserts secured and replaced? Inserts are secured with a Torx T8 screw (M2,5x5,5). Replacement requires the specified Torx key and adherence to the manufacturer’s torque recommendations for consistent seating. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
30mm Solid End Mill for WNMX 09T3 Indexable Inserts Internal Coolant, 150mm L - Teknik Makina
Combine high rigidity with coolant-assisted chip control for consistent surface quality and longer insert life; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Milling Cutter S804-1TM for WNMX 09T3 Indexable Inserts — 30 mm, Internal Coolant (Teknik Makina) The Milling Cutter S804-1TM is a precision cutter body designed for indexable milling with WNMX 09T3 inserts, suited to general and finishing machining where controlled coolant delivery and stable clamping are required. 30 mm diameter body for stable cutting Internal coolant for improved chip evacuation Compatible with Korloy WNMX 09T3 inserts 25 mm shank for rigid clamping Three cutting edges for balanced cutting Optimised cutting performance through internal coolant and geometry The cutter body delivers measurable improvements in tool life and process stability by combining an internal coolant channel with a compact cutting geometry. The integrated internal coolant directs lubricant and coolant straight to the cutting zone, reducing temperatures and improving chip evacuation, which in turn extends insert life and lowers the frequency of tool changes. With a 30 mm diameter and an insert system based on WNMX 09T3, the assembly supports repeatable machining results and consistent surface finish, particularly in operations that require close heat management. Rigidity and handling that support precision and productivity A solid 25 mm shank and a total length of 150 mm provide a balance between reach and stiffness, reducing vibration during engagement. The cutter features a 60 mm cutting length and three cutting edges, which distribute cutting forces evenly and enable efficient material removal while maintaining accuracy. The modest mass (approx. 0.591 kg) keeps handling straightforward during tool changes and minimises spindle load, making the tool body suitable for both roughing and semi-finishing passes where controlled deflection is important. Practical assembly and maintenance to reduce downtime The tool uses standard fixing hardware for straightforward service: retention screws are M3x7, tightened with a Torx T8 key, allowing quick insert changes and secure clamping. Compatibility with Korloy WNMX 09T3 indexable inserts ensures a wide choice of grades and chipbreakers for varied applications. For those unfamiliar, “indexable inserts” are replaceable carbide tips that locate into the cutter head; they can be rotated or exchanged without removing the entire cutter body, which simplifies maintenance and keeps production moving. For supply or application guidance on the Teknik Cutting Tools S804-1TM with internal coolant, contact Metav Werkzeuge in Emmerich for tailored advice and fast processing: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: S804-1TM SKU: S804-1TM Manufacturer: Teknik Makina Performance data Diameter: 30 mm Total length: 150 mm Shank diameter: 25 mm Cutting length: 60 mm Cutting edges: 3 Weight: 0.591 kg Special features Internal coolant For WNMX 09T3 indexable inserts Compatible insert manufacturer: Korloy Torx key: T8 Torx screw: M3x7 Product type: milling cutter FAQ What are the primary benefits of this milling cutter? The Milling Cutter S804-1TM (Teknik Cutting Tools, SKU S804-1TM) offers improved tool life and thermal control via internal coolant, together with a stiff 25 mm shank and balanced three-edged cutting for consistent machining results. Which inserts fit this cutter body? This cutter is designed for WNMX 09T3 indexable inserts; compatible grades and chipbreakers from Korloy can be fitted to match material and feed requirements. Is the tool suitable for finishing passes? Yes, the combination of a rigid shank, 30 mm body diameter and coolant delivery supports finishing and semi-finishing operations that demand surface quality and dimensional repeatability. How are inserts secured and changed? Inserts are fastened with M3x7 screws and require a Torx T8 key for tightening, enabling rapid indexation or replacement without extensive downtime. What should be expected regarding handling and spindle load? With an overall weight of approximately 0.591 kg and a compact geometry, the cutter offers moderate spindle load and manageable handling during tool changes, while delivering the stiffness needed for accurate cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Carbide End Mill For WNMU 0403 Indexable Inserts, 4 Flutes, 120mm Overall Length - Teknik Makina
Take advantage of a rigid Ø 32 mm tool body combined with a 4‑edge cutting concept and proven indexable‑insert compatibility for efficient, repeatable milling cycles; order the tool directly via Metav Werkzeuge or consult our technical advisers for application support. Shank Cutter S459TM – Indexable insert milling cutter for WNMU 0403, Ø 32 mm (Teknik Makina) The Shank Cutter S459TM is a robust indexable insert holder designed for WNMU 0403 inserts, offering stable peripheral milling and reliable tool life in workshop and industrial settings. Ø 32 mm cutting diameter 4 cutting edges for stable chip removal Compatible with WNMU 0403 inserts (ISCAR) Torx T8 screw M2.5x5.5 for secure clamping Higher rigidity for consistent surface quality and cycle times The solid tool body with a 32 mm diameter and a centred shank provides increased stiffness, which translates into lower vibration and more consistent surface finishes. With 4 cutting edges, the holder balances cutting force across the circumference, improving load distribution and enabling smoother material removal. This structural stability helps to reduce rework and supports shorter cycle times when paired with appropriate insert grades. Quick insert changes that cut costs and downtime Designed for WNMU 0403 indexable inserts, the holder allows rapid insert replacement without regrinding, delivering a measurable reduction in machine downtime. The secure clamping system—featuring Torx T8 engagement and a M2.5x5.5 clamping screw—ensures reliable seat contact and repeatability after each change. The result is predictable performance and easier tool management for batch production or mixed‑job workshops. Practical fit and handling for the machining floor With an overall length of 120 mm and a weight of 0.776 kg, the holder provides a good compromise between reach and rigidity for many milling tasks. The indexable system simplifies maintenance and inventory: stock a few insert grades and reuse the same holder across jobs. Assembly is straightforward with the specified Torx key; regular inspection of clamping torque and insert condition maintains safety and tool life. For tailored recommendations on insert grades and cutting parameters, technical guidance is available. For precise, durable milling with Teknik Makina quality, contact Metav Werkzeuge for procurement and application advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S459TM Manufacturer: Teknik Makina Suitable inserts: WNMU 0403 (ISCAR) Torx key: T8 Clamping screw: M2.5x5.5 Weight: 0.776 kg Diameter: 32 mm Overall length: 120 mm Number of cutting edges: 4 Dimensions & core data Diameter: 32 mm Shank diameter: 32 mm Overall length: 120 mm Weight: 0.776 kg Number of flutes/cutting edges: 4 Features & compatibility Compatible with ISCAR WNMU 0403 inserts Torx T8 clamping system Screw M2.5x5.5 Indexable insert holder Manufacturer: Teknik Makina FAQ Which indexable inserts fit this holder? The holder accepts WNMU 0403 indexable inserts; ISCAR‑type inserts are specified for correct seating and performance with the S459TM. What is the cutting diameter and overall length? The cutting diameter is 32 mm and the overall length is 120 mm, providing a balance of reach and rigidity for common milling operations. How many cutting edges does the tool provide? The tool features 4 cutting edges, designed to distribute cutting forces evenly and support stable machining. Which clamping fasteners are required? Clamping is achieved via a Torx T8 engagement and M2.5x5.5 screw; use the correct Torx key and ensure screws are tightened to the recommended torque for safe operation. Is the holder suitable for high‑volume production? Yes — the indexable system and secure clamping make the S459TM suitable for repetitive production where quick insert changes and consistent repeatability are required Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cartridge End Mill For APMT 1604 Indexable Inserts, 3 Flutes 55mm Cutting Length, 90° Cutting Angle - Teknik Makina
Benefit from the combination of APMT 1604 compatibility and a robust Ø32 mm shank for consistent shoulder milling performance; the compact total length and three cutting edges ensure stable chip evacuation and predictable tool life. Lightweight construction at 0.874 kg and secure Torx clamping deliver fast insert changes and low vibration. Order the (S248TM indexable milling cutter) directly via (Metav Werkzeuge) or ask our consultants if needed. S248TM indexable milling cutter by Teknik Makina — for APMT 1604 indexable inserts, Ø32 mm shank, 3 cutting edges S248TM is a precision-engineered indexable milling cutter designed for shoulder and face milling where repeatability and secure insert clamping are required. Ø32 mm shank diameter Compatible with APMT 1604 inserts Three cutting edges for stable cuts 90° cutting angle for shoulder milling Stable shoulder milling with predictable results The body is configured for a true 90° cutting angle, which makes it ideal for shoulder milling and square-corner operations where accuracy matters. Fitted for APMT 1604 indexable inserts, the cutter allows straightforward use of common triangular inserts that provide reliable edge geometry and consistent cutting forces. The three-edge configuration reduces load per edge during engagement, improving vibration damping and contributing to a smoother surface finish; this technical setup translates directly into fewer reworks and more consistent cycle times on production runs. Rigidity, run-out control and handling benefits A Ø32 mm shank and a total length of 150 mm deliver a practical balance between reach and stiffness for medium-reach milling tasks. The compact overall size reduces overhang, limiting deflection under load and improving dimensional control on shoulders and faces. At 0.874 kg, the cutter body is light enough for quick tool changes yet heavy enough to feel robust in the holder, which assists with stable axial contact and repeatable set-ups. These design choices help maintain tolerances in batch production and contribute to predictable tool life in serial workflows. Fast, secure insert clamping and maintenance Insert retention is achieved with a Torx M4x10 clamping screw, tightened using a T15 key, enabling secure fixation with minimal tool access. The simple screw-and-seat arrangement speeds up index changes and reduces downtime compared with more complex clamping systems. Compatibility with mainstream insert manufacturers such as Korloy ensures accessible replacement geometry and cost-effective stocking of spare inserts. The practical maintenance approach means quicker changeovers and a shorter mean time to repair for busy shops. Trusted supply and practical support from Metav Sourcing the cutter through Metav keeps procurement simple: Metav combines a wide product range with local stock management in Emmerich, which supports reliable delivery and quality filtering for the European market. As a partner with decades of metrology and tooling experience, Metav provides both the product and the technical assistance that help integrate tools into existing workflows. If clarification on fitment or clamping torque is required, Metav’s team can advise on holder compatibility and recommended operating parameters via email or phone. Contact Metav Werkzeuge for tailored advice on the S248TM indexable milling cutter and to secure compatible APMT 1604 inserts or spare Torx screws — expert assistance and immediate order handling from our Emmerich site Technical Data Article number: S248TM Manufacturer: Teknik Makina Brand: Teknik Makina SKU: S248TM ECLASS: 21180806 ETIM: EC011860 Facts Shank diameter mm: 32 Cutting edges: 3 Total length mm: 150 Cutting length mm: 55 Weight kg: 0.874 Special features Compatible inserts: APMT 1604 Compatible insert manufacturer: Korloy Clamping screw: M4x10 (Torx) Torx key size: T15 Cutting angle: 90° FAQ Which inserts fit this cutter? The S248TM indexable milling cutter is configured for APMT 1604 inserts; Korloy inserts in that designation are a suitable match for immediate use. What size shank and overall length does the cutter have? The cutter has a Ø32 mm shank and a total length of 150 mm, providing a balance between rigidity and reach. How are the inserts secured in the cutter? Inserts are secured with a Torx M4x10 clamping screw; a T15 key is used for tightening and removal. Is this cutter suitable for shoulder milling? Yes — the tool features a 90° cutting angle, making it well suited to shoulder milling and operations that require square-corner accuracy. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Corner Milling Cutter for APKT 1604 Indexable Inserts 3-Flute, 90° Cutting Angle - Teknik Makina
Benefit from a robust shank, extended cutting length and an indexable insert system that keeps tool changes fast and repeatable; the combination supports reliable cycle times and straightforward maintenance. Order the S446TM shank milling cutter directly via Metav Werkzeuge or ask the consultants if technical clarification is required. S446TM Shank milling cutter – Ø32 mm, for APKT 1604 indexable inserts (Teknik Makina) S446TM is a shank-mounted milling cutter designed for versatile machining with indexable inserts, ideal for production and job-shop environments where fast insert changes and stable cutting conditions are required Ø 32 mm shank diameter 70 mm effective cutting length Compatible with APKT 1604 inserts Torx screw M4x10, T15 key required Consistent cutting performance for efficient machining The tool delivers stable machining through a substantial 32 mm shank and a well-proportioned cutter body, which together reduce deflection in interrupted and continuous cuts. With a 70 mm cutting length and a 300 mm overall length, the design balances reach and rigidity so operators can programme longer axial engagements without compromising accuracy. The three robust cutting edges support repeatable chip formation and steady surface finish, making the cutter a pragmatic choice for batch work and series production. Fast insert changes and secure clamping to reduce downtime Designed for use with APKT 1604 indexable inserts and compatible with Korloy grades, the cutter prioritises quick insert replacement. The clamping system uses a M4x10 Torx screw and requires a T15 key, permitting safe, repeatable tightening torque and minimising setup time between operations. Reduced changeover duration translates directly into higher spindle utilisation and lower non-productive time on the shop floor. Built for workshop reliability and simple maintenance The cutter’s geometry—including a 90° cutting angle—supports predictable tool paths and straightforward programming on CNC milling centres. At 1.827 kg, the assembly is substantial enough to maintain stability while still being manageable for routine handling and inspection. The configuration with three inserts helps distribute cutting forces evenly, which contributes to longer insert life and lower overall tooling cost per part when paired with appropriate cutting data and insert grades. Practical advantages when sourced through Metav Sourcing the S446TM via Metav brings logistical and advisory benefits: the Emmerich location functions as a quality filter for European customers and provides access to technical consultation and coordinated supply. Combined with Metav’s broad catalogue and experience in precision tooling distribution, procurement of this shank milling cutter becomes part of a dependable workflow—from selection to delivery—so production planners can reduce supplier complexity and maintain consistent tool availability. For supply, technical advice or to discuss batch requirements for the S446TM from Teknik Makina, contact Metav Werkzeuge for personalised ordering and logistics support via info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data SKU: S446TM Manufacturer: Teknik Makina Article: Shank milling cutter for APKT 1604 indexable inserts Core data Shank diameter: 32 mm Cutting length: 70 mm Overall length: 300 mm Weight: 1.827 kg Number of cutting edges: 3 Cutting angle: 90° Special features For APKT 1604 indexable inserts Compatible with Korloy inserts Torx screw M4x10 Torx key T15 FAQ Which indexable inserts fit this milling cutter? The S446TM shank milling cutter accepts APKT 1604 indexable inserts and is compatible with Korloy grades specified for that insert type. What are the key dimensions to check for toolholding? Relevant dimensions are a 32 mm shank diameter, 70 mm effective cutting length and 300 mm overall length for programme clearance and holder compatibility. Which fastening hardware is required for insert clamping? Insert clamping uses a M4x10 Torx screw tightened with a T15 key as supplied or specified for the clamping system. Is the cutter suitable for long axial engagements? The combination of a 32 mm shank, three cutting edges and a 70 mm cutting length gives the tool adequate rigidity for extended axial engagements within the specified setup and machine capabilities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
32mm Cutter for ADKT 10T3 Indexable Inserts Internal Coolant L200mm - Teknik Makina
Take advantage of the combination of stable clamping, internal coolant and standardised ADKT 10T3 insert compatibility for uninterrupted production. Order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter 32 mm — internal coolant, ADKT 10T3 compatible (Teknik Makina) A Shank milling cutter designed for milling tasks with ADKT 10T3 indexable inserts, offering controlled coolant delivery and a robust 32 mm shank for repeatable set‑ups. 32 mm shank diameter for stable clamping Internal coolant for improved chip evacuation Compatible with ADKT 10T3 Korloy inserts Four cutting edges for balanced material removal Stability and repeatable set‑ups for efficient production The robust 32 mm shank and a 200 mm overall length combine to provide torsional stability and predictable vibration behaviour in serial production. This geometry reduces the need for frequent re‑adjustments and supports consistent machining results when using the appropriate insert body. The cutter’s construction and mass (approx. 1 kg) are selected to balance rigidity with reasonable handling weight, helping to maintain toolpaths and surface finish under standard CNC conditions. The tool is best described as an indexable insert milling cutter engineered to support efficient clamping and reliable repeatability across batches. Coolant-fed design and straightforward insert service An integrated internal coolant channel supplies coolant directly to the cutting zone, improving chip evacuation and cooling at the cutting edge—especially beneficial for medium‑duty finishing and semi‑roughing cycles where insert life matters. The cutter accepts ADKT 10T3 style inserts from Korloy, and replacement is secured via the specified fasteners. Service and reconditioning are simplified by the use of a standard T8 Torx key and M2.5x5.5 Torx screws, enabling quick insert changes and minimising downtime. With four cutting edges, the head offers a balanced engagement that helps distribute cutting forces and prolong insert life under repetitive passes. Practical compatibility for workshop toolsets Supplied under SKU S082TM by Teknik Makina, the design aligns with common insert inventories and workshop toolholders, reducing the need for specialised adapters. The 45 mm cutting length provides a practical reach for many pocketing and shoulder operations while the standardised insert family maintains interchangeability and cost efficiency. The combination of coolant routing, standardised fixing hardware and a conventional shank diameter supports straightforward integration into existing tool assemblies and reduces tooling complexity for production managers seeking predictable outcomes. Contact Metav Werkzeuge for a tailored application assessment of Teknik Makina’s 32 mm shank milling cutter (SKU S082TM) and to discuss suitable inserts and holder options Technical data SKU: S082TM ECLASS: 21180806 Manufacturer: Teknik Makina Core dimensions Diameter: 32 mm Shank diameter: 32 mm Overall length: 200 mm Cutting length (shank): 45 mm Number of cutting edges: 4 Weight: 1 kg Features & compatibility Internal coolant For ADKT 10T3 indexable inserts Compatible insert manufacturer: Korloy Torx key: T8 Torx screw: M2.5x5.5 FAQ Which inserts fit this cutter? The cutter accepts ADKT 10T3 indexable inserts; the tool has been specified for inserts from Korloy and for use with the ADKT geometry. How is coolant supplied to the cutting edge? Coolant is delivered via the tool’s internal coolant channel, directing coolant to the insert pocket and the cutting zone for improved chip evacuation. What tools are required to change an insert? Insert changes use a T8 Torx key and M2.5x5.5 Torx screws as supplied for secure fastening and quick replacement. How many cutting edges are available per head? The head features four cutting edges, arranged to provide balanced cutting forces and even wear distribution during operations. Which SKU identifies this product for ordering? This item is listed under SKU S082TM, supplied by Teknik Makina, and available through Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; eMail: info@metav-werkzeuge.com
32mm Cutter For ADKT 1706 Indexable Inserts With Internal Coolant, 45mm Cutting Length - Teknik Makina
Benefit from a robust milling solution that combines a stable 32 mm shank, precise compatibility with ADKT 1706 indexable inserts and integrated internal coolant for consistent chip control — purchase through Metav Werkzeuge or consult our specialists for tailored application support. 32 mm indexable insert milling cutter S065TM — internal coolant, for ADKT 1706 A 32 mm indexable insert milling cutter designed for efficient face and peripheral milling with ADKT 1706 inserts, featuring internal coolant and a compact L125 mm form for reliable workshop performance *32 mm shank diameter *Internal coolant for improved chip evacuation *Compatible with ADKT 1706 indexable inserts *Three cutting edges for smooth material removal High stability and predictable performance for industrial milling The tool body is built around a 32 mm shank and an overall length of 125 mm, providing the rigidity required for demanding milling tasks in production environments. As a purpose-made indexable insert milling cutter, it accepts ADKT 1706 inserts (compatible with Korloy standards), which permits rapid insert changes and consistent cutting geometry. This alignment of shank size, body length and insert system reduces vibration, improves dimensional accuracy and supports repeatable cycle times on milling centres and machining centres. Controlled cooling and simple maintenance to extend insert life Integrated internal coolant channels deliver cutting fluid directly to the cutting zone, enhancing chip evacuation and reducing thermal load on the cutting edges. The result is improved surface finish and extended tool life for the inserts. Fast clamp and replacement features are supported by the M4x10 Torx screw and T15 key interface, allowing swift servicing and minimising downtime. With three cutting edges, the cutter balances material removal rate and stability for a smooth cutting action in a range of general engineering materials. Practical integration and workshop readiness for everyday use Compact and lightweight at approximately 0.62 kg, the cutter mounts easily in standard toolholders with a 32 mm shank diameter and offers a 45 mm cutting length suited to both shoulder and light face milling operations. The construction focuses on reliability and repeatable setup, enabling efficient tool management in busy workshops. For application advice, Metav Werkzeuge provides practical guidance and product selection support to align the cutter with specific machining strategies and insert grades. Choose Teknik Makina's S065TM cutter for consistent, coolant-assisted milling — contact Metav Werkzeuge for application advice and delivery from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical details SKU: S065TM Manufacturer: Teknik Makina Label: 32mm shank cutter ADKT 1706 L125mm with internal coolant Core specifications Diameter: 32 mm Overall length: 125 mm Shank diameter: 32 mm Cutting length: 45 mm Cutting edges: 3 Weight: 0.62 kg Torx screw: M4x10 Torx key: T15 Features & compatibility Internal coolant Compatible with ADKT 1706 indexable inserts Compatible inserts manufacturer: Korloy Indexable insert milling cutter body Suitable for face and peripheral milling FAQ What inserts fit this cutter? The cutter accepts ADKT 1706 indexable inserts; compatibility with Korloy insert variants is specified for the S065TM indexable insert milling cutter by Teknik Makina. Is internal coolant supplied through the tool? Yes, the S065TM features internal coolant channels that feed the cutting zone directly to aid chip evacuation and prolong insert life. How is the insert secured and replaced? Inserts are secured with an M4x10 Torx screw tightened using a T15 key — the S065TM design allows quick replacement to reduce machine downtime. Which applications suit this cutter best? The indexable insert milling cutter is optimised for face and peripheral milling operations where a 32 mm shank and a 45 mm cutting length offer the necessary rigidity and reach. Can the cutter be used in standard holders? Yes, the 32 mm shank diameter of the S065TM is designed for integration into standard toolholders used in CNC milling centres and machining centres. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For APKT 1604 Indexable Inserts 3 Cutting Edges, 60mm Cutting Length, 90° - Teknik Makina
Take advantage of the combination of high compatibility with APKT 1604 indexable inserts, a 32 mm shank for rigidity and a long 60 mm cutting length for extended engagement. Order directly via Metav Werkzeuge or consult the Metav specialists for tailored advice. S436TM Shank Milling Cutter — 32 mm diameter, for APKT 1604 indexable inserts (Teknik Makina) S436TM is a precision shank milling cutter designed for use with APKT 1604 indexable inserts, offering robust toolholding and reliable insert clamping for demanding milling tasks. 32 mm shank diameter for stability For APKT 1604 indexable inserts Three cutting edges for productive material removal 250 mm overall length for deep reach High productivity through proven indexable insert technology The S436TM is engineered to exploit the advantages of indexable inserts: fast insert changes and consistent cutting geometry reduce downtime and secure reproducible results. With a 32 mm diameter shank and three cutting edges, the tool provides a stable platform that minimises vibration during feed, which in turn supports higher material removal rates and longer tool life. The compatibility with standard APKT formats keeps stocking simple and allows for immediate insert replacement during production. Secure clamping and quick serviceability for continuous operation Insert retention uses an M4x10 Torx screw tightened with a T15 key, ensuring repeatable clamping torque and quick servicing on the shop floor. The insert pocket accepts APKT 1604 inserts and matches insert geometries supplied by Korloy, enabling a wide choice of grades and chipbreakers. "Indexable insert" means the cutting part can be rotated or replaced independently of the tool body, which cuts tooling costs and shortens changeover times compared with solid-carbide solutions. Designed for stability and extended engagement A 60 mm cutting length combined with a 250 mm overall length gives the tool extended engagement for applications that demand reach while keeping the primary aim on rigidity. The tool’s mass of 1.52 kg contributes to a steady cutting behaviour and supports consistent surface finishes over longer passes. For operations where runout and chatter must be limited, this balance between diameter, length and weight helps to maintain process reliability. Practical procurement and support from Metav Werkzeuge Sourcing is simplified through Metav Werkzeuge’s European hub in Emmerich, which acts as a quality filter and logistics centre. The combination of a focused product range and technical competence means the S436TM can be supplied quickly and accompanied by practical application guidance. For complex machining tasks, the documented interface with APKT 1604 inserts allows process planners to match insert grade and geometry with cycle and material demands. For specialist advice on integrating the Teknik Makina S436TM shank milling cutter into an existing toolset or to arrange supply via Metav Werkzeuge (Emmerich), contact Metav Werkzeuge at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for reliable, timely support. Technical data Article number: S436TM Manufacturer: Teknik Makina Designation: Shank milling cutter for APKT 1604 indexable inserts ECLASS: 21180806 ETIM: EC011860 Core specifications Diameter: 32 mm Cutting length: 60 mm Overall length: 250 mm Number of cutting edges: 3 Cutting angle: 90° Weight: 1.52 kg Special features Compatible with APKT 1604 indexable inserts Compatible insert manufacturer: Korloy Torx screw: M4x10 Torx key size: T15 Brand: Teknik Makina SKU: S436TM FAQ What insert type fits this cutter? The cutter accepts APKT 1604 indexable inserts; the tool body is designed for that insert format and matches common APKT pocket geometries. Which screw and key are required for insert clamping? Insert clamping uses an M4x10 Torx screw and a T15 key for consistent torque and repeatable seating. What are the key dimensions of the cutter? Key dimensions are a 32 mm shank diameter, 60 mm cutting length and 250 mm overall length as specified for the S436TM. Is this tool compatible with Korloy inserts? Yes — the tool is noted as compatible with Korloy-manufactured APKT 1604 inserts, enabling use of those grades and chipbreakers. How does the cutter reduce downtime in production? By using indexable APKT 1604 inserts, the cutter allows quick insert changes and repeatable geometry, which shortens changeover times and reduces tooling inventory complexity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For APMT 1604 Indexable Inserts 3 Flutes 45mm Cutting Length 25mm Shank - Teknik Makina
Take advantage of a rigid cutting system that pairs indexable APMT 1604 inserts with a compact, stable shank — ideal for repeatable face and slot milling. Benefit from fast insert changes and a robust connection (Torx M4x10) to reduce downtime and maintain constant surface quality; order or consult via Metav Werkzeuge for delivery and technical advice. Shaft milling cutter S247TM — shank milling cutter, Ø32 mm, shank Ø25 mm (Teknik Makina) The Shaft milling cutter S247TM is a shank milling cutter designed for use with APMT 1604 indexable inserts, suited to general machining tasks where a 90° cutting angle and a compact overall length are advantageous. Compatible with APMT 1604 indexable inserts Rigid shank Ø25 mm for stable clamping Cutting diameter Ø32 mm with 3 cutting edges Torx M4x10 fastening screw, key size T15 Consistent chip control and reliable cutting performance The combination of indexable inserts and a purpose-built tool body delivers predictable chip evacuation and surface finish. Fitting APMT 1604 inserts (compatible with Korloy) means insert geometry and grade can be matched to the workpiece material; this yields faster setup and consistent machining even during medium-duty face or shoulder milling. The tool’s three cutting edges ensure balanced cutting forces, reducing vibration and improving tool life compared with single-edge solutions. In practical terms, this translates into fewer interruptions for tool change and more stable cycle times on the shop floor. Stiff shank and secure clamping for repeatable accuracy A shank Ø25 mm and an outer diameter of Ø32 mm create a compact yet rigid assembly that resists deflection under load. The cutting length 45 mm and overall length 120 mm are optimised for reach and stability, making the cutter suitable for confined setups where runout must be minimised. Fastening is by Torx M4x10 screw with T15 key engagement, providing a secure seat for the insert and straightforward replacement without special tooling. Reduced micro-movement at the insert pocket leads to improved surface finish and repeatability across batches. Practical workshop advantages and straightforward maintenance Using indexable tooling reduces consumable cost and simplifies maintenance: worn cutting edges are replaced in seconds instead of changing entire solid tools. The tool body’s compatibility with APMT 1604 inserts allows selection from a wide range of grades for specific materials, giving flexibility in daily production. The 90° cutting geometry supports effective shoulder and face milling operations, while the compact design makes the cutter a pragmatic choice for both small jobbing shops and larger production cells. Documentation and spare parts are readily managed, supporting a reliable supply chain and minimal downtime. Discuss specifications and delivery options with Metav Werkzeuge to evaluate how the Teknik Makina S247TM shank milling cutter can fit existing toolholders and improve machining consistency at your workshop in Emmerich Technical data Article number: S247TM Manufacturer: Teknik Makina Product name: Shaft milling cutter for APMT 1604 indexable inserts Facts Diameter: 32 mm Shank diameter: 25 mm Cutting length: 45 mm Overall length: 120 mm Number of cutting edges: 3 Weight: 0.495 kg Cutting angle: 90° Torx screw: M4x10 Special features Compatible with APMT 1604 indexable inserts Compatible insert manufacturer: Korloy Torx key size: T15 Brand: Teknik Makina Fast insert change, indexable system FAQ What insert type does this cutter accept? The shaft milling cutter accepts APMT 1604 indexable inserts; the tool body is designed for that insert geometry and suitable insert grades can be chosen according to material and cutting conditions. Is the cutter suitable for finishing operations? Yes, with the correct APMT 1604 insert grade and sharp geometry this cutter can deliver controlled finishes on faces and shoulders thanks to its balanced three-edge arrangement. What fastening hardware is used for the insert? The insert is secured with a Torx M4x10 screw; the specified key size for installation and removal is T15, ensuring a secure and repeatable clamp. Can this tool be used for slotting as well as face milling? The 90° cutting angle and compact geometry make the cutter suitable for light slotting and face milling where the specified cutting length and diameter match the application. What benefits does the shank diameter provide? A shank Ø25 mm increases rigidity in the holder, lowering deflection and improving repeatability during milling, which supports better surface quality and longer insert life. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For APXT 1003 Indexable Inserts 4 Flutes 40mm Cutting Length, 25mm Shank - Teknik Makina
Benefit from a combination of precise compatibility with APXT 1003 indexable inserts, a robust 25 mm shank and four cutting edges for stable, repeatable milling. Order the tool directly via Metav Werkzeuge or contact our consultants for technical clarification. Shank Cutter S171-1TM for APXT 1003 indexable inserts — 32 mm diameter, 25 mm shank (Teknik Makina) The Shank Cutter S171-1TM is a compact milling tool designed for indexable-insert face and shoulder milling in industrial production settings. Precision fit for APXT 1003 inserts 25 mm shank for stable toolholding 32 mm cutting diameter, 4 cutting edges Includes M2.5×5.5 Torx screw and T8 key Reliable machining performance with stable toolholding The S171-1TM delivers consistent material removal thanks to its 32 mm diameter and four cutting edges, which together enable even load distribution and steady cutting forces. The 25 mm shank ensures secure clamping in standard toolholders, reducing vibration and minimising chatter. These mechanical attributes translate into improved surface quality and repeatable component dimensions in serial production. Fast insert changes and reduced downtime Designed for use with APXT 1003 indexable inserts, the cutter accepts established insert formats (compatible with Korloy). The fastening uses an M2.5×5.5 Torx screw and a T8 key, allowing quick, tool-assisted insert replacement. Indexable inserts provide cost efficiency by restoring cutting edges without disposing of the entire cutter body, which helps to keep spindle time productive and maintenance straightforward. Compact design for controlled handling and setup With an overall length of 120 mm and a cutting length of 40 mm, the shank cutter balances rigidity and accessibility for shoulder and face milling applications. The specified 90° cutting angle supports perpendicular shoulder finishes and reliable contour transitions. At approximately 0.511 kg, the tool is manageable for handling and quick changeover procedures while maintaining the mass needed for steady cutting performance. For reliable integration of Teknik Cutting Tools components into the production line, request a technical consultation or place an enquiry with Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for precise ordering and application advice. Technical Data Article number: S171-1TM Manufacturer: Teknik Makina Designation: Shank cutter for APXT 1003 indexable inserts Compatible inserts: APXT 1003 Compatible insert manufacturer: Korloy Facts Diameter: 32 mm Shank diameter: 25 mm Cutting length: 40 mm Overall length: 120 mm Cutting edges: 4 Cutting angle: 90° Weight: 0.511 kg Torx screw: M2.5×5.5 Torx key: T8 Special features For APXT 1003 indexable inserts Compatible with Korloy inserts Indexable-insert design for economical edge replacement Stable shank design for reduced vibration FAQ Which inserts fit this cutter? The S171-1TM accepts APXT 1003 indexable inserts; compatibility includes Korloy-manufactured inserts of that designation. What shank diameter is required for mounting? The cutter has a 25 mm shank, so a corresponding holder or collet for 25 mm shanks is required for correct mounting. How many cutting edges does the tool provide? This shank cutter features four cutting edges, providing balanced cutting action for stable performance. Which screw and key are needed to secure the inserts? Insert fastening uses an M2.5×5.5 Torx screw and a T8 Torx key, as supplied on the product specification. What are the overall and cutting lengths? The overall length is 120 mm, with a cutting length of 40 mm, suitable for shoulder and face milling setups. What is the cutting angle of the tool? The tool is specified with a 90° cutting angle, optimised for perpendicular shoulder machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For APXT 1003 Indexable Inserts 90° Cutting Angle, 4 Flutes, 60mm Cutting Length - Teknik Makina
Take advantage of the combination of robust shank design, compatibility with APXT 1003 indexable inserts and secure Torx clamping for uninterrupted production. Order the shank milling cutter directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. Shank milling cutter S189TM — Indexable insert milling cutter, Ø 32 mm, for APXT 1003 inserts (Teknik Makina) The Shank milling cutter S189TM is an indexable insert milling tool engineered for reliable material removal in shop and production environments; it accepts APXT 1003 inserts and is intended for applications requiring a square shoulder and consistent surface finish. Diameter 32 mm shank Four cutting edges for stability 60 mm effective cutting length Compatible with APXT 1003 inserts Superior rigidity for repeatable accuracy The solid 32 mm shank gives the tool a high degree of rigidity, which translates into reduced vibration during heavy cuts and a more consistent surface finish. A rigid holder is especially relevant in milling applications where tool deflection would otherwise compromise tolerances; this insert-equipped cutter is therefore suited to tasks where dimensional stability and repeatable geometry are required. The robust construction also contributes to predictable tool life, lowering unplanned tool changes. Cost-efficient cutting through an indexable system The indexable design reduces per-cutting-edge cost by allowing worn tips to be replaced rather than the entire tool. Compatibility with APXT 1003 indexable inserts, a common format from Korloy, means replacement parts are readily available and inventory can be standardised across multiple holders. By using replaceable inserts, tool management is simplified and total tooling expenditure can be controlled without sacrificing performance or surface quality. Optimised geometry for shoulder and face operations A 90° cutting angle combined with 4 cutting edges and a 60 mm effective cutting length provides a good balance between material removal rate and surface integrity. The square approach is convenient for perpendicular shoulder milling and face operations where a defined corner form is needed. The cutter’s geometry supports stable chip formation and consistent chip evacuation when matched to appropriate cutting parameters and coolant strategies. Fast, reliable insert clamping and maintenance Insert retention is achieved via a Torx clamp screw specification M2.5x5.5, operated with a T8 key, enabling secure fixing and quick index changes. This standardised clamping method keeps maintenance time low and reduces the risk of incorrect torque application when routine checks are performed. The design promotes simple, repeatable insert changes and helps maintain process uptime in busy production settings. For tailored supply and local delivery from Emmerich, request the Teknik Makina S189TM through Metav Werkzeuge GmbH — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best insert grades and cutting data for specific materials. Technical data Article number: S189TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Compatible inserts: APXT 1003 Facts Diameter: 32 mm Shank diameter: 32 mm Cutting length: 60 mm Overall length: 200 mm Cutting edges: 4 Weight: 1.253 kg Cutting angle: 90° Special features Indexable insert system Compatible with APXT 1003 inserts Insert manufacturer compatibility: Korloy Torx clamp screw: M2.5x5.5 Required key: T8 Brand: Teknik Makina FAQ Which inserts are compatible with this milling cutter? The S189TM accepts APXT 1003 indexable inserts; compatibility with inserts from Korloy is specified for straightforward replacement. What are the key dimensions of the cutter? The cutter has a diameter and shank of 32 mm, a cutting length of 60 mm and an overall length of 200 mm. How many cutting edges are available and what is the approach angle? This insert milling cutter is fitted for 4 cutting edges and features a 90° cutting angle for square-shoulder milling. How are the inserts secured in the cutter body? Inserts are clamped with a Torx screw M2.5x5.5; the required screwdriver size is T8 to ensure secure fixing and repeatable clamping. For which operations is this cutter particularly suitable? With its square cutting angle and indexable heads, the tool is well suited to perpendicular shoulder milling and general face milling where defined corner geometry and steady material removal are needed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For BDMT 11T3 Indexable Inserts 90° Cutting Angle, 4 Flutes, 60mm Cutting Length - Teknik Makina
Take advantage of a rigid 32 mm shank and a 60 mm effective cutting length for stable, repeatable machining, combined with secure Torx clamping for reduced downtime; order directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter for BDMT 11T3 indexable inserts — 32 mm, 60 mm cutting length (Teknik Makina) The shank milling cutter for BDMT 11T3 indexable inserts is a purpose-built insert cutter for face and shoulder milling in medium‑duty CNC applications, offering a long reach and secure insert fixation 32 mm shank diameter 60 mm effective cutting length Compatible with BDMT 11T3 inserts (Kyocera) Secure Torx fixation M2.5x5.5, T8 key Secure clamping and standardised inserts for uninterrupted production A robust clamping concept reduces unplanned stoppages: the cutter uses a Torx M2.5x5.5 screw and a T8 key interface for positive insert retention, which keeps the indexable tips firmly seated under load. Compatibility with BDMT 11T3 inserts — including widely available Kyocera grades — simplifies tool logistics and shortens changeover time. The result is a predictable process where insert swaps are quick and mechanical play is minimised, supporting higher uptime and consistent component quality. Stable geometry that enhances machining accuracy and reach With a 32 mm shank and overall length of 200 mm, the tool delivers the rigidity required for stable milling while providing extended reach where required. The cutter offers 4 cutting edges across a 60 mm cutting zone and a 90° cutting angle, which together promote even material removal and surface consistency. The relatively substantial mass (approx. 1.294 kg) contributes to vibration damping, making the cutter suited to operations where edge life and dimensional repeatability are priorities rather than high‑speed trimming alone. Practical workshop advantages and straightforward integration Standardised fixing and a common insert form factor lower inventory complexity and make integration into existing toolholders straightforward. The design focuses on operability: widely used indexable inserts, a familiar Torx fastening system and clear dimensional data (shaft diameter, cutting length, overall length) permit reliable tool planning and stock management. For buyers requiring traceable parts and dependable delivery, Metav Werkzeuge provides procurement continuity and localised technical advice from Emmerich, backed by an extensive catalogue of compatible tooling. For procurement support and reliable supply from Metav Werkzeuge, request the full specification or contact our advisors in Emmerich to confirm suitability for the intended machining tasks. Technical data SKU: S574TM Manufacturer: Teknik Makina Product: Shank milling cutter for BDMT 11T3 indexable inserts Compatible insert type: BDMT 11T3 (Kyocera) Facts Shaft diameter: 32 mm Effective cutting length: 60 mm Overall length: 200 mm Number of cutting edges: 4 Cutting angle: 90° Weight: 1.294 kg Design & features Torx screw M2.5x5.5 Torx key size T8 Compatible with Kyocera BDMT 11T3 indexable inserts FAQ Which indexable inserts fit this tool? The cutter accepts BDMT 11T3 indexable inserts; Kyocera inserts in this geometry are compatible and commonly used. How is the insert secured in the cutter? Insert retention is achieved with a Torx M2.5x5.5 screw; the specified key size is T8, providing secure clamping for the indexable tip. What are the key dimensions to check for toolholder compatibility? Relevant dimensions are a 32 mm shaft diameter, 60 mm effective cutting length and 200 mm overall length; the tool also has 4 cutting edges and a 90° cutting angle. For which machining tasks is this cutter best suited? The design is intended for face and shoulder milling in medium‑duty CNC operations where a rigid 32 mm shank and extended reach are advantageous. Is the Torx key included with the delivery? The product data specifies the Torx screw size and the key size T8; inclusion of the key in the delivery is not stated in the available specification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For LNGU 15T6 Indexable Inserts 3-Flute 90° Cutting Angle 45mm Cutting Length, M4x11 Torx T15 - Teknik Makina
Take advantage of a robust, insert-compatible cutter body that combines precise holding with easy serviceability; the combination of a Ø32 mm shank, 45 mm cutting length and compatibility with LNGU 15T6 indexable inserts ensures consistent milling performance. Order the S951TM directly via Metav Werkzeuge or ask our consultants if needed. Shaft Milling Cutter S951TM — indexable insert cutter, Ø32 mm, for LNGU 15T6 (Teknik Makina) The Shaft Milling Cutter S951TM is a precision cutter body designed to accept LNGU 15T6 indexable inserts, providing a stable platform for face and peripheral milling where secure insert clamping and repeatable geometry matter Compatible with Kennametal inserts Ø32 mm shank diameter 45 mm cutting length Fastening screw M4x11, Torx T15 Stable insert clamping for reliable machining results The S951TM's design focuses on secure insert retention and repeatable positioning to reduce vibration and maintain surface quality. With a Torx M4x11 fastening arrangement operated by a T15 key, the insert retention system is straightforward to service and minimises downtime. For planners and workshop managers this means reliable cycle times and fewer interruptions during production, since insert changes are quick and require only common tooling. The stable clamping also supports consistent cutting geometry across batches, contributing to predictable component tolerances. Dimensions and geometry that support precise cutting Engineered with a Ø32 mm shank and a 45 mm cutting length within an overall length of 150 mm, the cutter body balances stiffness and accessibility for a variety of milling set-ups. The specified 90° cutting angle provides neutral engagement for many turning and milling operations with LNGU 15T6 indexable inserts, enabling straightforward toolpath planning. The component weight of 0.884 kg helps with dynamic stability in moderate-speed spindles while remaining manageable for manual tool changes. These measurable values assist purchasing and process engineers when assessing toolholder compatibility and machine load. Compatibility and workshop integration for practical use Designed to accept the LNGU 15T6 insert family and compatible with inserts from Kennametal, the cutter body integrates into existing insert systems without the need for special adapters. The three cutting edges configuration supports even chip distribution when the appropriate insert geometry is selected. Documentation available with the product provides the necessary torque recommendation for the M4x11 screw and guidance on insert seating; this supports maintenance teams in keeping the tool in optimal condition and reduces the risk of incorrect assembly. The cutter body’s straightforward interface makes it a practical choice for production workshops and jobbing shops alike. Contact Metav Werkzeuge to discuss the S951TM, confirm insert compatibility and obtain procurement assistance from our Emmerich team via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: S951TM Manufacturer: Teknik Makina Product: Shaft milling cutter for LNGU 15T6 indexable inserts Facts Diameter: 32 mm Shank diameter: 32 mm Cutting length: 45 mm Overall length: 150 mm Number of cutting edges: 3 Weight: 0.884 kg Cutting angle: 90° Fastening screw: M4x11 (Torx T15) Special features Compatible with Kennametal LNGU 15T6 inserts Indexable insert system Torx M4x11 fastening, key T15 FAQ Which inserts fit this cutter body? The S951TM accepts LNGU 15T6 indexable inserts and is noted as compatible with inserts from Kennametal for direct replacement. What are the key dimensions to check for machine setup? Key dimensions are Ø32 mm shank diameter, 45 mm cutting length and 150 mm overall length; these determine clearance and clamping requirements. What fastening hardware is used for the inserts? Inserts are secured with an M4x11 Torx screw; assembly and disassembly use a T15 Torx key. How many cutting edges does the toolbody provide? The cutter body presents 3 cutting edges for operation with the specified LNGU 15T6 inserts. Is there guidance on torque or maintenance? Basic torque and seating guidance are supplied with the tool; Metav Werkzeuge can provide specific recommendations for the S951TM and matching insert clamping procedures. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter for LNMX 0603 Indexable Inserts L150mm With Internal Coolant - Teknik Makina
Take advantage of the combination of secure clamping, internal coolant and broad insert compatibility for consistent high-output machining. Order the cutter directly via Metav Werkzeuge or consult our specialists for application-specific setup and rapid delivery from Emmerich. Indexable Milling Cutter S287-1TM – 32 mm shank, internal coolant (Teknik Makina) The Indexable Milling Cutter S287-1TM is a robust shank-mounted cutter engineered for LNMX 0603 indexable inserts, designed to deliver reliable chip control and stable material removal in medium- to high-feed milling applications. *Internal coolant for reliable chip removal *32 mm shank for secure machine clamping *Compatible with LNMX 0603 (Korloy) inserts *Five cutting edges increase material removal rate Increase throughput with coolant-assisted chip evacuation The integrated internal coolant channel focuses cutting fluid directly at the cutting zone, reducing heat and improving chip evacuation for longer insert life and fewer tool changes. In practical terms, this means more continuous production time and fewer interruptions for maintenance. The coolant-fed design is particularly advantageous in deep or interrupted cuts where chip control is critical; it supports consistent surface quality while helping keep temperatures down in the cutting zone. Stable clamping and repeatable performance for batch production A 32 mm shank provides a rigid connection to the spindle, reducing chatter and improving dimensional stability across runs. The tool’s construction, combined with the three-point clamping geometry common to shank-mounted indexable cutters, ensures secure seating and repeatable positioning of the cutting head. This stability translates into reduced scrap rates and tighter process control during batch machining or series production. High-efficiency cutting with compatible LNMX 0603 inserts Designed for LNMX 0603 indexable inserts and compatible with Korloy grades, the cutter uses five cutting edges to distribute cutting forces and extend productive time between indexings. The 70 mm cutting length allows deep shoulder cuts and step milling without compromising rigidity. Operators benefit from straightforward insert changes using the supplied Torx hardware specification, while process planners gain flexibility by selecting insert grades tailored to aluminium, steel or mixed-material applications. Practical serviceability and shop-floor integration Service and routine maintenance are simplified with common fasteners and a clear specification for replacement parts: Torx key T8 and Torx screw M3x7 are industry-standard sizes, making spare parts easy to source. The tool’s S287-1TM SKU and durable construction reduce downtime through predictable maintenance cycles. For workshops aiming to centralise procurement and minimise supplier complexity, this cutter integrates seamlessly into a standard tooling set-up for CNC milling centres. Choose the Teknik Makina S287-1TM for robust, coolant-fed machining and contact Metav Werkzeuge in Emmerich for expert application advice and fast supply—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S287-1TM Manufacturer: Teknik Makina Product type: Indexable milling cutter Label: 32mm Schaftfräser LNMX 0603 L150mm mit Innenkühlung Core dimensions Shank diameter: 32 mm Overall length: 150 mm Cutting length: 70 mm Number of cutting edges: 5 Weight: 1.516 kg Torx key: T8 Torx screw: M3x7 Materials & compatibility Compatible inserts: LNMX 0603 Compatible insert manufacturer: Korloy Internal coolant: yes Suitable for indexable inserts FAQ What inserts fit this cutter? The S287-1TM is specified for LNMX 0603 indexable inserts; Korloy grades are listed as compatible for flexible grade selection. Does the cutter have internal coolant? Yes, the S287-1TM features internal coolant routing to the cutting edge to assist chip evacuation and temperature control. What are the key dimensions for machine setup? Key dimensions: 32 mm shank diameter, 150 mm overall length and 70 mm cutting length; use these values when programming tool offsets. How many cutting edges does the tool use and what is the benefit? The tool uses five cutting edges, which helps distribute cutting forces and improve material removal rates with extended index intervals. Which fasteners are required for insert clamping? Insert clamping uses a Torx T8 key and M3x7 Torx screws for secure and standardised servicing. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For LOEX 0804 Indexable Inserts 40mm Cutting Length, 3 Flutes - Teknik Makina
Take advantage of a high-stability cutting solution that combines a 32 mm shank, compatibility with LOEX 0804 indexable inserts, and a 200 mm overall length for extended reach; order the tool directly via Metav Werkzeuge or consult our specialists for insert selection and delivery options. Shank cutter S297TM – 32 mm shank, for LOEX 0804 indexable inserts (Teknik Makina) Shank cutter S297TM designed for reliable indexable-insert milling in workshop and light production environments, optimised for compatibility with LOEX 0804 inserts and SECO-style clamping systems. 32 mm shank diameter Compatible with LOEX 0804 indexable inserts 200 mm overall length for extended reach Three cutting edges for stable machining Stable performance with industry-standard inserts The S297TM is engineered for consistent chip control and repeatable results through the use of LOEX 0804 indexable inserts, a widely adopted insert format. Indexable inserts separate the cutting edge from the tool body, enabling rapid insert changes and predictable geometry life, which translates into reduced machining downtime and easier inventory management. The tool’s compatibility with SECO-style inserts ensures straightforward sourcing of replacement inserts and proven cutting grades. Secure clamping and straightforward insert changes A robust clamping arrangement and standardised fasteners mean downtime is minimised. The holder accepts inserts fastened with a T8 Torx key and M2.5x7 screw, enabling secure fixing with minimal setup time. This configuration supports reliable repeatability in production runs and reduces the risk of insert movement during interrupted cuts. For operations where fixture time and reliable torque are critical, the standard Torx interface helps maintain consistent clamp force and tool life. Rigidity and reach for deeper milling tasks With a 32 mm shank and 200 mm overall length, the tool offers an advantageous balance between reach and stiffness. The 40 mm cutting length permits extended engagement in deep slots or stepped profiles while the three cutting edges promote stable cutting dynamics and reduced vibration compared with higher-flute alternatives. The result is improved surface quality and a lower tendency for chatter when working in medium-depth milling applications. Practical fit for workshops and small-series production Designed for pragmatic use in maintenance shops and production cells, this shank cutter simplifies tooling decisions by supporting a common insert family. The combination of a standardised insert interface, compact inventory requirements and straightforward fastening makes it suitable for flexible manufacturing where fast changeovers and predictable performance are priorities. The construction supports modular tooling strategies and is compatible with typical milling holders used across the industry. For technical advice and delivery from Metav Werkzeuge, request the Teknik Makina S297TM via our Emmerich team — consultants are available to recommend suitable LOEX 0804 grades and to coordinate fast, reliable supply; eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 Technical Data SKU: S297TM Label: 32mm Shank cutter LOEX 0804 L200mm Manufacturer: Teknik Makina Facts Diameter: 32 mm Shank diameter: 32 mm Overall length: 200 mm Cutting length (shank): 40 mm Cutting edges: 3 Weight: 0.904 kg Special features Compatible inserts: LOEX 0804 (indexable inserts) Compatible insert manufacturer: SECO Torx key: T8 Torx screw: M2.5x7 FAQ Which indexable inserts fit this shank cutter? The shank cutter accepts LOEX 0804 indexable inserts; replacement inserts from SECO-compatible ranges are suitable for the S297TM. How many cutting edges does the tool have? The tool is supplied with three cutting edges, optimised for stability and consistent material removal during milling. What are the key dimensions to consider when fitting the tool? Key dimensions are 32 mm shank diameter, 200 mm overall length and 40 mm cutting length, which determine holder choice and available reach for the S297TM. Which fastener and key are required for insert changes? Insert clamping uses an M2.5x7 screw tightened with a T8 Torx key; this arrangement provides secure fixing and repeatable clamp torque. Is this tool suitable for flexible workshop tooling strategies? Yes; compatibility with standard LOEX 0804 inserts and SECO-style insert families makes the shank cutter well suited to workshops and small-series production where quick insert swaps and limited inventory are advantages. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For RDMT 12T3 Indexable Inserts, 3 Flutes 45mm Cutting Length, 200mm Overall - Teknik Makina
Take advantage of robust compatibility and proven rigidity: the combination of a Ø32 mm shank and support for RDMT 12T3 indexable inserts ensures stable milling and repeatable results. Order the shank milling cutter directly via Metav Werkzeuge or request specialist advice from the consultants. Shank milling cutter R246TM — for RDMT 12T3 indexable inserts, Ø32 mm shank (Teknik Cutting Tools) The R246TM shank milling cutter from Teknik Cutting Tools is engineered for indexable-insert milling with a focus on stability and straightforward maintenance, designed to suit medium-duty to heavy finishing operations where consistent chip control and tool life are required. Compatible with RDMT 12T3 indexable inserts Ø32 mm shank for high rigidity 45 mm effective cutting length Torx fastening with T15 key Higher productivity through controlled chip formation The cutter is configured for use with indexable inserts to deliver predictable chip flow and consistent surface finish. Thanks to the RDMT 12T3 interface, insert changeover is rapid and repeatable, reducing downtime between setups. This results in measurable cycle-time improvements on repeated features while enabling conservative costs per cutting edge through simple insert replacement. The combination of insert geometry and the tool’s geometry supports reliable evacuation of swarf, which helps maintain cutting temperatures and extends cutter life. Stable clamping for reliable machining performance Designed around a Ø32 mm shank, the tool offers enhanced rigidity and resistance to deflection in interrupted and continuous cuts. The 45 mm cutting length provides an effective engagement depth for deeper passes without compromising stability. Integral fastening details—such as the M3.5 locking screw and the Torx screw M3.5x8.5 secured with a T15 key—ensure secure retention of the insert carrier under loads common in milling operations. The resulting reduction in vibration translates into improved dimensional repeatability and extended insert life. Practical fitment and workshop advantages The tool’s straightforward specification simplifies tool selection for production and maintenance teams: a standard Ø32 holder interface, compatibility with widely used RDMT 12T3 inserts and a compact overall length of 200 mm allow for easy integration into existing tool inventories. Weight and balance have been considered so that the cutter behaves predictably during accelerations and changes in feed, supporting safer toolhandling and reduced setup complexity. For operations seeking a balance of performance and economy, this cutter provides a dependable option with minimal compromise. Discuss application requirements with Metav Werkzeuge to select the ideal Teknik Cutting Tools shank milling cutter R246TM for Ø32 mm toolholders and to arrange direct supply from Emmerich Technical data Article number: R246TM Manufacturer: Teknik Makina Model description: Shank milling cutter for RDMT 12T3 Indexable Inserts ECLASS: 21180806 ETIM: EC011860 Numbers / core technical data Shank diameter: 32 mm Cutting length (shank): 45 mm Overall length: 200 mm Weight: 1.201 kg Number of cutting edges: 3 Diameter: 32 mm Special features Compatible inserts: RDMT 12T3 Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 SKU: R246TM FAQ Which indexable inserts fit this cutter? The cutter accepts RDMT 12T3 indexable inserts; the R246TM is designed specifically for that insert format to ensure correct seating and reliable performance. What holder interface is required? A toolholder with a Ø32 mm shank reception is required for correct clamping and rigidity when using this Teknik Cutting Tools cutter. How deep can the cutter engage in a single pass? The cutter offers an effective cutting length of 45 mm, which sets the practical maximum engagement for a single axial pass while maintaining stability. What fastening components are included for the insert? Fastening is specified with an M3.5 locking screw, a Torx screw M3.5x8.5 and a T15 Torx key for secure and repeatable insert clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For TPKN 1103-2204 Indexable Inserts 45mm Cutting Length, M6x14 Torx Screw - Teknik Makina
Take advantage of a compact combination of rigidity and quick insert changes to keep machining precise and productive; the robust 25 mm shank and 32 mm cutting diameter ensure stable engagement, while compatibility with TPKN 1103 indexable inserts reduces downtime — order directly via Metav Werkzeuge or discuss integration with our consultants. Indexable Milling Cutter S124TM — 32 mm, 3 Cutting Edges (Teknik Makina) The Indexable Milling Cutter S124TM is a shank-mounted milling tool designed for use with TPKN 1103–2204 indexable inserts, suited to workshop and CNC applications that require fast insert changes and consistent cutter rigidity 32 mm cutting diameter 25 mm shank diameter Compatible with TPKN 1103 inserts Fast insert fastening M6x14 Stable cutting performance for consistent production The tool is engineered around a 25 mm shank diameter to maximise rigidity at the spindle interface, reducing deflection under load and improving surface finish consistency. With a 32 mm diameter and 3 cutting edges, the cutter balances chip evacuation and cutting forces; this geometry supports steady material removal and helps to extend insert life through more uniform wear distribution. The overall compact design and a mass of 0.48 kg contribute to predictable dynamic behaviour on high-speed spindles, which is particularly beneficial when repeatability and cycle-time stability are priorities for production runs. Rapid clamping and low-maintenance handling Insert retention is secured by an M6x14 Torx screw, with the documented key size noted as 3 Allen, enabling quick and reliable insert changes that reduce machine downtime. The tool’s 45 mm cutting length (shank-mounted) gives sufficient engagement for many common machining tasks while keeping the insert accessible for swift replacement. This combination of accessible clamping and a standardised insert interface simplifies inventory management and tool-change procedures on the shop floor, increasing overall workshop efficiency without complex adjustments. Practical fitment and workshop advantages Designed specifically for TPKN 1103 indexable inserts (also compatible with TPKN 1103–2204 insert series), the cutter eases tool configuration by using a widely available insert type. The unit’s 120 mm overall length and standard dimensions make it suitable for conventional tool holders where a compact footprint is required. For procurement managers and process engineers, the clear specification reduces uncertainty in tool selection and supports predictable machining outcomes; for machinists, the familiar insert format and straightforward fastening allow confident, repeatable changeovers during shift work. Contact Metav Werkzeuge today to discuss how the S124TM indexable milling cutter can be integrated into current machining setups or to request application-specific advice — Metav Werkzeuge is available by phone at +49 2822 7131930 or by email at info@metav-werkzeuge.com Technical Data Article number: S124TM Manufacturer: Teknik Makina Designation: Indexable milling cutter for TPKN 1103-2204 indexable inserts EClass: 21180806 ETIM: EC011860 Facts Cutting diameter: 32 mm Shank diameter: 25 mm Cutting length (shank): 45 mm Number of cutting edges: 3 Overall length: 120 mm Weight: 0.48 kg Torx screw: M6x14 Torx key: 3 Allen Special features For TPKN 1103 indexable inserts Compatible with TPKN 1103-2204 indexable inserts Brand: Teknik Makina SKU: S124TM FAQ Which inserts fit this cutter? The S124TM is designed for TPKN 1103 indexable inserts and is listed as compatible with the TPKN 1103–2204 insert series. How is the insert clamped? Insert clamping is carried out with an M6x14 Torx screw; the specification records a 3 Allen key reference for the fastening. What are the key dimensions to check for toolholder compatibility? Check the 25 mm shank diameter, the 32 mm cutting diameter and the 120 mm overall length against the toolholder and spindle clearance requirements. How many cutting edges does the cutter have and what is the benefit? The cutter employs 3 cutting edges, which support balanced cutting forces and more even insert wear, improving run stability. Is the cutter heavy to handle during tool changes? Weighing 0.48 kg, the S124TM has a compact mass that facilitates safe and easy handling during insert swaps and tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For VCGT 1604 Indexable Inserts 2 Flutes 60mm Cutting Length, 250mm Overall - Teknik Makina
Combine robust indexable-insert compatibility with a precise 32 mm shank and a practical 60 mm cutting length to keep production running with consistent results; order the S726TM directly via Metav Werkzeuge or request bespoke application advice from our consultants. Shank Milling Cutter S726TM — 32 mm shank, for VCGT 1604 indexable inserts (Teknik Makina) A Shank Milling Cutter S726TM designed for indexable-insert milling, offering repeatable seating for VCGT 1604 inserts and reliable performance in general workshop and light industrial applications. 32 mm shank diameter Compatible with VCGT 1604 inserts 60 mm cutting length Torx screw M4x10 supplied Precise clamping and fast insert changes for reliable production The S726TM is built to reduce downtime through a secure clamping concept and standardised insert compatibility. The combination of a rigid 32 mm shank and the VCGT 1604 insert system allows for fast indexable-insert replacement while maintaining consistent tool position. This stability translates into fewer adjustments at the machine and shorter set-up times, contributing to higher machine availability and predictable output. Designed dimensions that support machining stability Key dimensions such as the 60 mm cutting length and 250 mm overall length are balanced to deliver effective reach without unnecessary overhang. The relatively compact profile and two cutting edges make the tool suitable for light to medium-duty face and shoulder milling where vibration control and surface finish are important. The mass of 1.25 kg aids in stabilising the toolholder assembly during interrupted cuts. Compatible fastening and maintenance made straightforward A simple fastening arrangement using a Torx M4x10 screw and a T15 key standardises routine servicing and insert changes. The use of common fasteners reduces the risk of tool-holder damage during maintenance and keeps consumable handling uncomplicated. For workshops aiming to streamline maintenance procedures, this standardisation supports quick, repeatable interventions. Practical benefits for shops and small-scale production Beyond technical fit, the S726TM offers a pragmatic route to indexable-insert milling when cost-efficiency and flexibility are priorities. Compatibility with VCGT 1604 inserts allows shops to choose from a wide range of grades and geometries for varied materials, while the robust shank diameter supports steady cutting conditions. The result is an efficient, versatile cutter body that contributes to consistent parts quality and predictable cycle times. Contact Metav Werkzeuge for tailored machining recommendations or to discuss procuring the Teknik Makina S726TM from our Emmerich warehouse. Technical Data SKU: S726TM Brand: Teknik Makina Article name: Shank milling cutter for VCGT 1604 indexable inserts Core data Shank diameter: 32 mm Cutting length: 60 mm Overall length: 250 mm Number of cutting edges: 2 Weight: 1.25 kg Features Compatible with VCGT 1604 indexable inserts Torx screw M4x10 Torx key size T15 Two cutting edges FAQ Which insert type is recommended for this cutter? The S726TM is designed for VCGT 1604 indexable inserts; select an insert grade and geometry that matches the workpiece material and desired surface finish. What is the shank diameter and why does it matter? The tool has a 32 mm shank diameter, which improves rigidity and helps reduce vibration for more consistent milling results. How long is the cutting section and the overall tool? The cutter provides a 60 mm cutting length with a 250 mm overall length, offering reach with reduced overhang for better stability. What fastening hardware is used for the inserts? Insert retention uses a Torx M4x10 screw (Torx key T15), simplifying maintenance and ensuring repeatable clamping torque. Is the S726TM suitable for heavy roughing operations? The S726TM is optimised for light to medium-duty milling; for heavy roughing, consider tools with larger shank diameters or specialised heavy-duty bodies. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For VDKT 11T2 Indexable Inserts Internal Coolant, 125mm L - Teknik Makina
Take advantage of the combination of 32 mm shank rigidity, internal coolant and compatibility with VDKT 11T2 indexable inserts for reliable, repeatable milling. Order the cutter directly via Metav Werkzeuge or request technical advice from the consultancy team for an efficient tool changeover. Shank milling cutter S401TM – 32 mm shank, internal coolant (Teknik Makina) A Shank milling cutter S401TM engineered for efficient indexable-insert milling, designed to accept VDKT 11T2 indexable inserts and to perform across a range of industrial milling tasks with coolant-through capability and a 125 mm overall length. 32 mm shank diameter for rigid clamping Internal coolant for optimised tool life Compatible with VDKT 11T2 indexable inserts 125 mm overall length for deep reach Consistent chip evacuation and coolant advantage for longer tool life The cutter is built around a coolant-through body that delivers a continuous supply of coolant directly to the cutting zone. This internal coolant functionality reduces heat at the cutting edge and improves chip evacuation, which in turn extends insert life and stabilises cutting forces. For workshops seeking predictable cycle times, the coolant feed lowers thermal distortion and supports higher metal-removal rates with stable surface finish, particularly when machining demanding materials using indexable-insert tooling. Rigidity and reach for accurate, heavy-duty milling A 32 mm shank provides the necessary stiffness for precision milling and reduces deflection under load, while the 125 mm overall length combined with a 40 mm cutting length enables access to recessed features without compromising stability. The cutter accepts four cutting edges, allowing balanced cutting and smooth engagement. The Torx clamping system (T8 key, M2.5x5.5 screw) ensures repeatable insert fastening and straightforward maintenance, supporting short set-up times and consistent process reliability on CNC machines. Compatibility and application scope for production environments Designed to accept inserts from Korloy in the VDKT 11T2 format, the tool body offers economical indexable-insert replacement and flexible grade selection for various workpiece materials. The combination of a robust shank, insert-based cutting, and coolant-through design makes this cutter suitable for batch production and job-shop environments that prioritise throughput and reproducible part quality. Lightweight for its class at approximately 0.684 kg, the tool body balances handling ease with industrial performance. For tailored technical guidance on Teknik Makina’s S401TM shank milling cutter with internal coolant, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: S401TM Product type: Shank milling cutter Manufacturer: Teknik Makina SKU: S401TM Label: 32mm shank milling cutter VDKT 11T2 L125mm with internal coolant Facts Shank diameter: 32 mm Overall length: 125 mm Cutting length: 40 mm Number of cutting edges: 4 Weight: 0.684 kg Torx key: T8 Torx screw: M2.5x5.5 Special features Internal coolant (coolant-through) Compatible with VDKT 11T2 indexable inserts Insert manufacturer compatibility: Korloy FAQ Which insert type fits this cutter? The cutter is designed for VDKT 11T2 indexable inserts; inserts from Korloy in that format are compatible with the tool body. Does the tool provide coolant-through capability? Yes, the S401TM features internal coolant, supplying coolant directly to the cutting zone to improve tool life and chip control. What clamping system is used for the inserts? The cutter uses a Torx screw system (T8 key, M2.5x5.5 screw) for reliable and repeatable insert clamping on the S401TM tool body. What dimensions are relevant for setup and toolholder selection? Key dimensions include a 32 mm shank diameter, 125 mm overall length, and a 40 mm cutting length, which inform toolholder choice and reach assessment. Is this cutter suitable for production milling? Yes, the combination of a rigid shank, coolant-through design and indexable inserts makes the S401TM well suited to production and high-throughput milling applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
32mm Cutter For WNMX 1305 Indexable Inserts, 2 Flutes, M4x10 Torx Fixing - Teknik Makina
Take advantage of the combination of a 32 mm shank for outstanding rigidity, precise compatibility with WNMX 1305 inserts and a compact 120 mm overall length for efficient, low‑vibration milling; order directly via Metav Werkzeuge or consult our specialists for process optimisation. Shank milling cutter S800TM — indexable insert cutter with 32 mm shank (Teknik Makina) The Shank milling cutter S800TM is a robust indexable insert cutter engineered for secure clamping and repeatable milling with WNMX 1305 inserts, suitable for workshop and industrial CNC applications 32 mm shank diameter Compatible with WNMX 1305 inserts Two cutting edges for efficient machining Includes M4x10 Torx clamp screw Stable clamping for improved surface finish and tool life A large 32 mm shank delivers increased rigidity at the spindle, which reduces deflection and vibration during side and face milling. The solid shank diameter, combined with the short overall reach of 120 mm overall length, helps to maintain concentricity under load and promotes a consistent surface quality. The secure screw fixation using an M4x10 Torx clamp screw and a T15 key reduces the risk of insert loosening and simplifies maintenance, resulting in fewer unplanned stoppages and a steadier production output. Insert system that reduces downtime and simplifies logistics Designed for the widely used WNMX 1305 insert format, the tool accepts standard inserts from recognised manufacturers such as Korloy, enabling easy replenishment and inventory standardisation. The indexable arrangement with two cutting edges permits quick corner indexing and replacement without regrinding, which shortens service intervals and lowers overall tooling costs. Adopting a common insert family also streamlines procurement and reduces the variety of spares kept in stock. Compact geometry for accessible machining and reliable handling With a total length of 120 mm overall length and a strong 32 mm shank, the toolbody is engineered to reach confined work zones while maintaining stiffness. The compact geometry supports stable chip formation and effective evacuation when paired with correctly selected inserts, helping to preserve insert life and dimensional accuracy. The configuration is particularly suitable for medium‑duty milling operations where a balance of reach and rigidity is required. Contact Metav Werkzeuge for tailored advice on integrating the S800TM into existing toolsets and to arrange reliable supply from Emmerich with expert technical consultation Technical data Article number: S800TM SKU: S800TM Manufacturer: Teknik Makina Compatible inserts: WNMX 1305 Suitable insert manufacturer: Korloy Facts Shank diameter: 32 mm Overall length: 120 mm Cutting edges: 2 Torx screw: M4x10 Torx key: T15 eClass: 21180806 ETIM: EC011860 Special features Indexable insert system Secure Torx clamping Compact reach for improved rigidity Suited to workshop and CNC environments FAQ Which insert type fits this cutter? The cutter accepts WNMX 1305 indexable inserts; compatibility is specified for the S800TM and common sources include Korloy. What is the shank diameter and why does it matter? The 32 mm shank of the S800TM improves rigidity and reduces vibration, leading to better surface finish and longer insert life. How is the insert secured and which tool is required? Inserts are held by an M4x10 Torx clamp screw; a T15 Torx key is used for insertion and indexing on the S800TM. Is the tool suitable for deep reach operations? The 120 mm overall length provides moderate reach while keeping stiffness; the S800TM is best for medium‑reach milling where stability is important. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter For XEKT 1904 Indexable Inserts With Internal Coolant, 150mm Length - Teknik Makina
Benefit from the combination of stable shank support, internal coolant and broad insert compatibility for reliable milling performance. The 32 mm shank and coolant-through design deliver improved clamp stability and extended tool life while compatibility with XEKT 1904 inserts reduces tooling complexity. Order the cutter directly via Metav Werkzeuge or ask our consultants if needed. Indexable milling cutter S387TM – 32 mm shank, internal coolant (Teknik Makina) The Indexable milling cutter S387TM is an indexable milling tool engineered for use with XEKT 1904 indexable inserts, combining coolant-through capability with a robust 32 mm shank for stable, industrial metal cutting. 32 mm shank diameter for stable clamping Internal coolant supply for improved tool life Compatible with XEKT 1904 inserts (Korloy) 150 mm overall length, 71 mm cutting length Precision and rigidity for consistent machining A large-diameter shank ensures reduced runout and reliable clamping force; the 32 mm shank provides the mechanical stiffness required for repeatable results in series production. The cutter’s mass contributes to vibration damping while the balanced geometry supports consistent chip engagement. This translates into measurable process stability and fewer reworks, supporting throughput goals in milling operations. Coolant-through design that protects tooling and cycle time The internal coolant route supplies cutting fluid directly to the cutting zone, enhancing chip evacuation and reducing thermal load at the cutting edge. By keeping the insert seat and cutting edge cooler, the internal coolant arrangement helps to slow wear progression and maintain cutting performance across longer tool lives. For combined roughing and semi-finishing sequences, this feature contributes to lower downtime and more predictable machining windows. Insert system engineered for flexibility and cost control Designed for XEKT 1904 indexable inserts and matched to Korloy grades, the tool body accepts proven insert geometries to address a wide range of workpiece conditions. Fast insert changes are achieved with the supplied screw standard M4x8.5 and a T15 Torx interface, simplifying maintenance and inventory. Using standardised inserts supports lower stocking complexity and easier selection of carbide grades for specific applications. Practical integration and maintenance in the production cell With an overall length of 150 mm and a 71 mm cutting length, the tool balances reach and rigidity for many milling setups. The two cutting edges deliver efficient material removal while minimising unnecessary tool overhang. Identification by SKU S387TM supports spare-part tracking and procurement. The robust construction and standardised fastening mean straightforward assembly into existing toolholders without special adapters. For tailored advice on procurement or application of this Teknik Makina indexable milling cutter, contact Metav Werkzeuge for prompt technical consultation and order handling. Technical data SKU: S387TM Product type: Indexable milling cutter Compatibility: XEKT 1904 inserts (Korloy) Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Overall length: 150 mm Cutting length: 71 mm Weight: 0.773 kg Cutting edges: 2 Torx key: T15 Screw size: M4x8.5 Special features Internal coolant Compatible with Korloy inserts For XEKT 1904 indexable inserts Label: 32 mm shank L150 mm internal coolant FAQ Which inserts fit this cutter? The S387TM is designed for XEKT 1904 indexable inserts; Korloy is listed as the matching insert manufacturer for this cutter. Does the cutter provide coolant to the cutting edge? Yes, the indexable milling cutter S387TM features internal coolant to the cutting zone for improved chip evacuation and edge temperature control. What are the shank and cutting dimensions? Shank diameter is 32 mm, overall length is 150 mm, cutting length is 71 mm, and the tool weight is 0.773 kg for the S387TM. How are the inserts secured and serviced? Inserts are clamped with M4x8.5 screws tightened using a T15 Torx key; this standardisation enables quick insert changes and straightforward maintenance on the S387TM. Is this tool suitable for production environments with frequent insert changes? Yes, the S387TM’s standardised fastenings and compatibility with XEKT 1904 inserts support rapid insert swaps and lower inventory complexity, making it suitable for dynamic production workflows. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
32mm Cutter for XNKT 0604 Indexable Inserts L150mm Internal Coolant - Teknik Makina
Take advantage of the combination of rigid 32 mm shank support, internal coolant and compatibility with common XNKT 0604 indexable inserts for stable, repeatable milling cycles; order directly via Metav Werkzeuge or consult our technical team for application support. Shank cutter for XNKT 0604 indexable inserts — 32 mm shank, internal coolant (Teknik Makina) Shank cutter for XNKT 0604 indexable inserts designed for secure clamping and optimised chip evacuation in medium‑duty milling tasks 32 mm shank diameter for rigid clamping Internal coolant for effective chip evacuation Compatible with Korloy XNKT 0604 indexable inserts 150 mm overall length with 4 cutting edges Stable clamping for consistent machining results The wider 32 mm shank delivers increased rigidity in the toolholder, reducing deflection under load and improving dimensional consistency. Combined with a 150 mm overall length and a 40 mm cutting head, the geometry is balanced to keep tool vibrations low while maintaining access to common milling positions. The four cutting edges of the design increase the material engagement per rotation, which translates into higher productivity and smoother surface finish during slotting or face milling operations. This configuration helps shops retain tighter tolerances with fewer tool changes and less rework. Coolant-through design that prolongs tool life Equipped with internal coolant, the cutter directs cutting fluid close to the insert interface, enhancing chip evacuation and heat control at the cutting zone. This reduces thermal wear on the insert seat and supports longer insert life across interrupted cuts. Inserts are secured with an M3x7 Torx screw and a T8 Torx key, ensuring reproducible clamping torque and quick index changes. The tool is optimised for the XNKT 0604 insert family and is compatible with Korloy inserts, allowing integration into established inventory systems and simplifying reordering. Practical integration and workshop efficiency Designed for indexable‑insert milling, the tool reduces the number of solid cutters required and minimises downtime for regrinding. The cutter’s specification supports flexible use in shoulder milling, light ramping and general face operations where productivity and repeatability are priorities. The unit is supplied under SKU S841-1TM, making identification and procurement straightforward for production planning. For operations seeking a reliable milling solution that fits common insert standards, the combination of a stiff shank, coolant feed and standard fastening offers a pragmatic route to improved cycle times and lower per-part tooling cost. Contact Metav Werkzeuge for tailored technical advice and to source the Teknik Makina shank cutter with internal coolant (SKU S841-1TM) for reliable integration into existing machining lines Technical data SKU: S841-1TM UID: S841-1TM Product type: Shank cutter Designation: Schaftfräser Secondary designation: for XNKT 0604 indexable inserts Manufacturer: Teknik Makina Label: 32mm Schaftfräser XNKT 0604 L150mm mit Innenkühlung Facts Diameter: 32 mm Overall length: 150 mm Shank diameter: 32 mm Cutting head length: 40 mm Number of cutting edges: 4 Weight: 0.941 kg ECLASS: 21180806 Special features Internal coolant (coolant-through) Compatible with XNKT 0604 indexable inserts Suitable for Korloy inserts Torx screw M3x7 for insert clamping Torx key T8 required FAQ What insert type fits this cutter? The cutter is designed for XNKT 0604 indexable inserts; Korloy‑type inserts are compatible and commonly used with this tool. Is the tool coolant‑through? Yes, the cutter features internal coolant, which feeds fluid directly to the cutting zone to improve chip evacuation and thermal control. What is the shank diameter and why is it important? The shank diameter is 32 mm. A larger shank increases rigidity in the toolholder, reducing deflection and improving machining accuracy. How are the inserts secured? Inserts are fixed with an M3x7 Torx screw and require a T8 Torx key for secure and repeatable clamping. Which operations is the cutter intended for? The tool is intended for indexable‑insert milling tasks such as face milling, shoulder milling and light ramping where stability and quick insert changes are beneficial. Can the cutter be identified for ordering? Yes, the cutter is listed under SKU S841-1TM, which simplifies procurement and inventory management. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
High-performance shank cutters and ball nose cutters for efficient milling
Insert shank cutters and ball nose cutters combine flexibility and productivity for a wide range of milling tasks. The category covers steel-bodied shank cutters fitted with indexable inserts for economical roughing, face milling, cornering and slotting, as well as ball nose cutters for contouring and 3D finishing.
How these tools work and where they belong
Shank cutters with indexable inserts use a carrier body made from hardened steel; the cutting edges are provided by removable inserts rather than a solid tool blank. Where tools do not have internal coolant, process heat and chips are managed via external coolant nozzles or compressed air, which is sufficient for open, surface-level and easily accessible milling on standard materials. Shank cutters with internal coolant feature fine internal channels that deliver coolant or blasting air directly to each cutting edge under pressure. This targeted supply is essential for deep pockets, cavities, full slotting and machining of heat-resistant or difficult-to-machine materials, because it prevents chip re-cutting, protects cutting edges from thermal overload and enables higher feed rates and improved surface quality.
Cut cycle times and reduce tooling costs
- Replaceable indexable inserts reduce consumable costs and shorten tool change time.
- Targeted internal coolant improves chip evacuation and extends insert life.
- Robust steel carrier bodies enable heavy-duty roughing without frequent tool replacement.
- Suitable for roughing, planing, corner milling and slot milling as well as precision 3D profiling with ball nose cutters.
A practical choice for purchasing and stocking tools
Metav brings a pragmatic purchasing advantage: a broad range of milling solutions is available from a single European quality hub. Metav’s focus on democratising precision means workshops benefit from a wide assortment, consistent quality control from Emmerich and steady supply — supported by decades of expertise and over 48,000 satisfied customers. Choose Metav for a centralised sourcing strategy that reduces supplier complexity while keeping access to both insert milling cutters (also referred to as insert milling cutters or indexable end mills) and ball nose cutters (also known as ball nose end mills or radius cutters) straightforward.
Quick summary
Insert shank cutters and ball nose cutters deliver flexible, cost-effective milling: replaceable inserts lower running costs, and internal coolant options enable higher performance and longer tool life where chip control is critical.
FAQ
When should I choose a shank cutter with indexable inserts rather than a solid carbide end mill?
Choose shank cutters with indexable inserts for economical roughing and high-stock-removal tasks where replacing inserts is preferable to replacing an entire tool; they are especially effective for face milling, cornering and slotting operations.
Does internal coolant make a measurable difference for ball nose cutters?
Yes. Internal coolant directed to each cutting edge reduces chip re-cutting and thermal stress, which improves surface finish and increases insert life when machining deep pockets, cavities or heat-resistant materials.
Can shank cutters without internal coolant be used for general workshop milling?
Absolutely. Tools without internal coolant rely on external coolant nozzles or compressed air and are well suited to open, superficial and easily accessible milling on standard materials.
What milling operations are shank cutters for indexable inserts typically used for?
Shank cutters with indexable inserts excel at economical roughing, planfräsen (face milling), corner milling and slot milling; ball nose cutters are the preferred choice for 3D profiling and finishing operations.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com