Efficient shaft cutters and ball nose cutters for versatile milling
Shaft cutters and ball nose cutters serve as robust rotating tools for roughing, face milling, corner milling and slotting, offering economical replacement of indexable inserts rather than whole solid tools. Available in versions with internal coolant to feed lubricant directly to each cutting edge or without internal coolant relying on external nozzles, these cutters ensure effective chip evacuation and thermal control suited to standard materials or deep pocket and cavity work. By preventing chip re-cutting and protecting cutting edges, they deliver higher feed rates, improved surface finish and extended tool life in demanding metalworking applications.
150mm End Mill For WNMX 0603 Indexable Inserts With Internal Coolant, 17mm Shank - Teknik Makina
Take advantage of the tool’s internal coolant and compact 17 mm cutting diameter for improved tool life and consistent chip control; the 16 mm shank and 150 mm overall length deliver stable clamping and reach for demanding setups. Order the shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shank milling cutter for WNMX 0603 indexable inserts — 17 mm cutting diameter, internal coolant (Teknik Makina) The Shank milling cutter for WNMX 0603 indexable inserts is a coolant-fed milling solution designed for precise, repeatable indexable-insert milling in industrial workshops and production environments. 17 mm cutting diameter Internal coolant for improved cooling Compatible with Korloy WNMX 0603 inserts T8 Torx key and M2.5x6.5 screws supplied Precision and consistent chip control for stable milling The tool combines a 17 mm cutting diameter with a 40 mm cutting length and a robust 150 mm overall length to balance reach and rigidity. Fitted for WNMX 0603 indexable inserts, the design uses internal coolant to route cutting fluid directly to the cutting zone, which reduces heat build-up and improves edge life. Two cutting edges contribute to a stable cutting action and predictable chip formation, making the cutter suitable for frequent changeover and serial machining where reproducible results are required. The 16 mm shank ensures secure clamping in common toolholders and collets, supporting accurate concentricity and reduced runout. Simple maintenance and secure assembly for shop-floor efficiency The assembly is engineered for straightforward servicing: insert fixation with an M2.5x6.5 screw and a T8 Torx interface simplifies insert changes and minimises downtime. Compatibility with Korloy WNMX 0603 inserts allows use of widely available indexable grades, lowering stocking complexity and enabling fast replenishment. Internal coolant passages reduce the need for complex external nozzling and help keep the workpiece and insert cooler during interruptions, which translates into fewer unexpected tool changes. The compact mass (approx. 0.241 kg) and balanced geometry make handling the tool in the workshop easier while keeping the focus on process reliability. Cost-efficiency through replaceable cutting edges and trusted tooling By using indexable inserts rather than solid cutting edges, this cutter reduces long-term tooling costs: worn edges are swapped quickly without removing the full tool from the spindle, and production pauses are minimised. The internal coolant provision supports longer insert life and a more consistent surface finish, helping to uphold quality standards across batches. Produced by Teknik Makina, the shank milling cutter pairs industrial-grade manufacture with practical serviceability, offering a pragmatic solution for operations that require dependable, repeatable milling performance. Contact Metav Werkzeuge in Emmerich to confirm fitment and order Teknik Makina’s coolant-fed shank milling cutter; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com for immediate assistance. Technical data Article number: S903-1TM EClass: 21180806 UID: S903-1TM Dimensions & weights Cutting diameter: 17 mm Overall length: 150 mm Shank diameter: 16 mm Cutting length: 40 mm Number of cutting edges: 2 Weight: 0.241 kg Features & compatibility Internal coolant: yes Compatible inserts: WNMX 0603 Compatible insert manufacturer: Korloy Torx key: T8 Torx screw: M2.5x6.5 Manufacturer: Teknik Makina FAQ What insert type does this cutter take? The cutter is designed for WNMX 0603 indexable inserts, enabling quick insert changes and familiar insert geometries. Is internal coolant supplied through the tool? Yes, the tool features internal coolant channels to direct cutting fluid to the insert cutting edge for improved cooling and chip control. Which shank diameter is required for the holder? A 16 mm shank diameter is specified, so holders or collets matched to a 16 mm shank are required for correct clamping. Are the fastening components included for insert mounting? The cutter specification lists an M2.5x6.5 screw and a T8 Torx interface, which are provided for secure insert mounting and straightforward servicing. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Face Mill For APKT 1705 Indexable Inserts, 4 Flutes, 40mm Diameter - Teknik Makina
Take advantage of a tool that combines precise compatibility with APKT 1705 indexable inserts and a robust 32 mm shank for stable machining; order the cutter directly via Metav Werkzeuge or consult our specialists for integration advice. Shank cutter S664TM — Shank cutter for APKT 1705 indexable inserts, Ø 40 mm, 4 flutes The Shank cutter S664TM is a precision milling head engineered for use with APKT 1705 indexable inserts, designed to deliver stable, repeatable results in indexable-insert milling applications. Four cutting edges for efficient material removal Diameter 40 mm for stable machining 32 mm shank for secure clamping Compatible with APKT 1705 indexable inserts Stable, vibration‑resistant clamping for consistent part quality The combination of a 32 mm shank and an outer diameter of Ø 40 mm gives the tool a high moment of inertia, which reduces chatter and improves surface quality in interrupted and continuous cuts. With an overall length of 150 mm and a cutting length of 60 mm, the design balances reach and rigidity to support predictable toolpaths and repeatable geometries. The tool’s mass of 0.85 kg contributes to stability without compromising handling during tool changes. These dimensional characteristics translate into fewer rejected parts and a steadier process window, so cycle times can be optimised with confidence. Fast, secure insert changes minimise downtime Insert retention is achieved with a standard M4x10 Torx screw tightened with a T15 key, enabling swift and reliable replacement of worn cutting edges. The indexable system accepts APKT 1705 inserts, a widely used insert format that keeps tooling costs down by allowing multiple cutting edges per insert. The straightforward fastening method reduces maintenance time at the machine and simplifies inventory: fewer complete cutters are required because inserts can be rotated or replaced independently. This arrangement supports efficient shift‑turnover procedures and lowers the mean time to repair in busy production environments. Predictable performance and straightforward integration into tooling stocks With four cutting edges, the cutter offers balanced engagement and even chip distribution for many common milling operations where APKT insert geometry is appropriate. Compatibility with inserts from established suppliers such as Taegutec ensures easy sourcing and replacement. The tool’s geometry and standardised fastening mean it can be integrated into existing toolholders and workflows without bespoke adaptations. For procurement and toolroom planning, the clear specifications — diameter, shank size, cutting length and Torx screw type — make lifecycle calculation and spare‑parts management straightforward, supporting lean stock strategies and reliable supply. Contact Metav Werkzeuge to discuss technical fitment, availability and supply options for the Teknik Makina S664TM shank cutter compatible with APKT 1705 indexable inserts Technical data Article number: S664TM Manufacturer: Teknik Makina Type: Shank cutter for APKT 1705 indexable inserts Dimensions & weight Diameter: 40 mm Shank diameter: 32 mm Cutting length: 60 mm Overall length: 150 mm Weight: 0.85 kg Number of cutting edges: 4 Compatibility & fittings Compatible inserts: APKT 1705 Compatible insert manufacturer: Taegutec Torx screw: M4x10 Torx key: T15 FAQ Which insert format is required for this cutter? The shank cutter accepts APKT 1705 indexable inserts; the tool is supplied to work with that insert format for easy sourcing. How are inserts secured in the cutter? Inserts are clamped with an M4x10 Torx screw tightened using a T15 key, allowing fast and secure insert changes. What are the key dimensions to consider when planning toolholders? Important dimensions are Ø 40 mm diameter, 32 mm shank diameter, 60 mm cutting length and 150 mm overall length; the cutter weighs 0.85 kg. Is the cutter compatible with Taegutec inserts? Yes, the cutter is compatible with APKT 1705 inserts from manufacturers such as Taegutec, facilitating straightforward replacement. What machining advantages does the indexed system provide? The indexable design of the cutter reduces tooling cost per cutting edge and shortens downtime for maintenance, making it suitable for operations where predictable tool costs and rapid insert changes are priorities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Face Milling Cutter for ADMT 1606 Indexable Inserts, 4 Flutes, 90° Cut, 32mm Shank Diameter - Teknik Makina
Take advantage of a robust milling solution that combines a 40 mm diameter, four cutting edges and a 60 mm cutting length for efficient material removal and consistent surface finish; order the cutter directly via Metav Werkzeuge or consult our technical team for application advice. Shank milling cutter S469TM – 40 mm diameter, 4 flutes (Teknik Makina) The Shank milling cutter S469TM is designed for indexable-insert milling with ADMT 1606 inserts, offering a rigid shank layout for stable, repeatable operations in production and workshop environments 40 mm cutting diameter Four cutting edges for consistent removal Shank 32 mm for increased rigidity Compatible with ADMT 1606 Walter inserts Greater metal removal with stable cutter geometry With a 40 mm diameter and four flutes, the tool provides a combination of chip removal rate and surface control that suits continuous milling operations. The 60 mm cutting length delivers extended engagement for shoulder and face milling while the 90° cutting angle ensures a predictable corner geometry. The indexable-insert concept reduces toolholding variability: individual inserts are clamped to a precise seat so the overall tool runout remains low, which in turn secures surface quality and extends effective tool life. This measurable setup translates into fewer interruptions and a more reliable production rhythm. Fast insert changes and secure clamping reduce downtime A robust Shank Ø 32 mm gives the assembly high torsional stiffness in the holder, improving chatter resistance under elevated cutting forces. Insert retention is via an M4x10 Torx screw operated with a T15 key, a standardised solution that balances torque transmission with quick serviceability. The screw system allows repeatable clamp preload for each replacement insert, meaning maintenance intervals are predictable and changeovers are efficient. Using industry-standard indexable inserts such as ADMT 1606 keeps spare-part logistics simple and supports fast on-machine recovery. Designed for workshop and production reliability At an overall length of 150 mm and a weight of 0.927 kg, the cutter is dimensioned for stable handling and compatibility with common milling arbors. Compatibility with Walter-type ADMT 1606 inserts supports cross-sourcing flexibility, while the solid construction from Teknik Makina addresses the need for dependable, everyday performance. The tool's design focuses on reducing total machining cost by combining replaceable cutting edges with a durable shank, which lowers the cost per cutting edge and simplifies inventory management in a centralised workshop environment. For reliable high-performance milling with ADMT 1606 inserts, request availability or technical clarification from Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: S469TM Manufacturer: Teknik Makina Designation: Shank milling cutter for ADMT 1606 indexable inserts Facts Diameter: 40 mm Shank diameter: 32 mm Cutting length: 60 mm Overall length: 150 mm Cutting edges: 4 Weight: 0.927 kg Cutting angle: 90° Special features Compatible with ADMT 1606 indexable inserts (Walter) Torx screw M4x10, Torx key T15 SKU: S469TM FAQ What insert type does the cutter use? The cutter accepts ADMT 1606 indexable inserts; the tool is supplied as a shank milling cutter compatible with Walter-style ADMT 1606 inserts. How is the insert secured on the tool? Inserts are fastened with an M4x10 Torx screw tightened using a T15 key, providing repeatable clamping force and quick changeover for the S469TM shank milling cutter. Is the shank suitable for heavy milling operations? The S469TM has a 32 mm shank diameter that improves rigidity and reduces the risk of chatter, making the tool suitable for demanding milling tasks in production settings. What are the key dimensions to check for holder compatibility? Relevant dimensions are the 40 mm cutting diameter, 32 mm shank diameter and 150 mm overall length; these determine fitment in standard arbors and toolholders. Who manufactures this milling cutter? The cutter is produced by Teknik Makina and distributed via Metav Werkzeuge as SKU S469TM for industrial and workshop use. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Indexable Cutter 32mm Shank Internal Coolant For AP-- 1604 Inserts, 3 Flutes - Teknik Makina
Take advantage of a compact combination of stable machining and efficient coolant delivery that reduces tool wear and maintains process reliability; order via Metav Werkzeuge or consult the team for application-specific advice. Schaftfräser – 32 mm shank, internal coolant (Teknik Makina) The Schaftfräser is a 32 mm shank milling cutter designed for use with AP-- 1604 indexable inserts, intended for industrial milling where reliable chip evacuation and rapid insert changes are required. 32 mm shank diameter Internal coolant supply Compatible with AP-- 1604 inserts Three cutting edges for stable machining Stable performance with dedicated coolant feed Equipped with an integrated internal coolant channel, this shank milling cutter ensures directed coolant delivery to the cutting zone, which improves tool life and chip evacuation under higher material removal rates. The combination of a 32 mm shank and a 150 mm overall length provides a balance between reach and rigidity; the targeted coolant flow further reduces heat build-up, keeping cutting edges sharper for longer and enabling consistent cycle times on series production runs. Precision and rigidity for repeatable results The tooling accepts AP-- 1604 indexable inserts in a three‑insert configuration, giving a favourable tool geometry for smooth cutting forces and reduced vibrations. With a 55 mm cutting length and an overall weight of 0.876 kg, the assembly offers predictable deflection characteristics; this is particularly beneficial when maintaining tight tolerances or when working with hard-to-machine components where stability directly translates into fewer rejects and less rework. Fast servicing and straightforward consumables handling Insert retention uses a Torx T15 drive and M4x10 screws, allowing quick, repeatable insert changes with standard workshop tools and minimising downtime during tool replacement. The tool is supplied under SKU S270-1TM, making reorders and tool management straightforward for procurement systems. Compatibility with Korloy AP-- 1604 inserts ensures broad availability of grade and geometry options to match different materials and cutting strategies. Practical fitment and machining guidance Designed as a shank-mounted cutter for use in milling holders and conventional toolholders, the cutter's dimensions and balanced insert arrangement support use on both horizontal and vertical machining centres. The internal coolant channel is particularly effective when machining abrasives or when chip control is critical. For process setup, start with conservative cutting parameters and increase feeds as stability and surface finish confirm the chosen setup is suitable. Discuss Teknik Makina's 32 mm shank milling solution with Metav Werkzeuge to match the S270-1TM to specific workpieces and machine capabilities, ensuring an efficient and robust machining process. Technical data SKU: S270-1TM Label: 32mm Schaftfräser AP-- 1604 L150mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 32 mm Overall length: 150 mm Shank diameter: 32 mm Cutting length: 55 mm Number of inserts: 3 Weight: 0.876 kg Special features Internal coolant Compatible with AP-- 1604 indexable inserts Compatible insert manufacturer: Korloy Torx key: T15 Torx screw: M4x10 FAQ Which inserts fit this cutter? The cutter accepts AP-- 1604 indexable inserts; compatible inserts from Korloy are suitable for the mounting and geometry of this shank milling cutter. Does the tool provide internal coolant? Yes, internal coolant is integrated into the design to supply coolant directly to the cutting zone, improving tool life and chip evacuation for the S270-1TM. What is the usable cutting length? The tool offers a cutting length of 55 mm, providing a balance between reach and rigidity for stable machining operations. Which drive and screws are required for insert changes? Insert retention uses a Torx T15 drive and M4x10 screws to secure the AP-- 1604 inserts, enabling quick and repeatable servicing. Is this suitable for high-feed operations? The combination of a 32 mm shank and three-indexable inserts, together with directed coolant, supports increased feed rates where machine rigidity and correct parameter selection allow. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Milling Cutter For WNMX 0603 Indexable Inserts, 2 Flutes 90° Cutting Angle, 16mm Shank - Teknik Makina
Take advantage of a compact, indexable-insert solution that combines precision with easy maintenance — a 17 mm cutting diameter, 40 mm cutting length and secure Torx clamp give reliable repeatability in production environments; order the S903TM directly via Metav Werkzeuge or ask our consultants for tailored advice. S903TM shank milling cutter by Teknik Makina — Ø17 mm, 2 flutes, for WNMX 0603 inserts The S903TM is a shank milling cutter designed to accept WNMX 0603 indexable inserts, engineered for secure clamping and consistent chip control in general machining and light to medium milling operations. Compatible with WNMX 0603 inserts 17 mm cutting diameter for compact machining 40 mm cutting length for extended engagement Torx clamp M2.5 x 5.5 with T8 key Repeatable accuracy for series production The tool provides consistent cutting geometry through its precision shank and insert interface, which reduces runout and stabilises tool behaviour during repeating cycles. The combination of a Ø17 mm cutter body and a 40 mm cutting length delivers a balance between reach and rigidity, meaning fewer reworks and a more predictable process flow. For operations where component tolerances matter, this construction minimises vibration and helps keep surface finish within tighter specifications. Fast insert changes and secure clamping for uptime A clear benefit of the design is the Torx clamping system (M2.5 x 5.5) requiring a T8 key, which enables swift insert replacement and precise torque application. Quick, repeatable clamping shortens tool-change intervals and makes tool handling more efficient on busy shop floors. The two-flute geometry supports reliable chip evacuation, so each insert maintains cutting performance longer and tool change frequency is reduced — directly supporting higher overall equipment effectiveness. Versatile compatibility and straightforward integration Designed to accept WNMX 0603 indexable inserts and compatible with Korloy plate types, the cutter fits existing insert inventories and makes retrofitting simple. The shank diameter of 16 mm and an overall length of 150 mm give a compact footprint while remaining adaptable to common collet and holder systems. This ease of integration means reduced setup time when switching between operations and a faster return to full production. Practical advantages for the workshop Lightweight at 0.24 kg yet robust in build, the cutter is a pragmatic choice for workshops seeking a dependable insert-holder that keeps spindles and holders in their nominal working ranges. The 90° cutting angle provides predictable engagement for face and peripheral milling alike, while the two cutting edges present a cost-effective solution where tool inventory management and rapid turnarounds are priorities. The tool’s simple geometry makes inspection and maintenance straightforward, reducing downtime for routine checks. For reliable high-performance milling backed by Teknik Makina engineering, contact Metav Werkzeuge in Emmerich for precise product guidance and prompt supply: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: S903TM Product: Shank milling cutter for WNMX 0603 indexable inserts Manufacturer: Teknik Makina Ø cutting diameter: 17 mm Shaft diameter: 16 mm Cutting length: 40 mm Overall length: 150 mm Number of flutes: 2 Weight: 0.24 kg Cutting angle: 90° Torx screw: M2.5 x 5.5 Torx key: T8 Compatible inserts: WNMX 0603 Recommended insert maker: Korloy Flute count: 2 Shank form: straight shank Application: indexable-insert milling FAQ What insert type fits this cutter? The cutter accepts WNMX 0603 indexable inserts; it is set up to work with Korloy-type plates so existing WNMX 0603 stocks can be used. What is the cutting diameter and overall length? The tool offers a 17 mm cutting diameter with an overall length of 150 mm, delivering a compact solution for confined set-ups. How is the insert secured and maintained? Inserts are clamped with a Torx screw (M2.5 x 5.5) tightened with a T8 key, allowing quick, repeatable insert changes and secure clamping for stable cutting. Which applications suit this shank cutter? The shank milling cutter is suited to light and medium milling tasks that benefit from an indexable-insert strategy, where quick insert swaps and cost-effective cutting edges are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Milling Cutter For WNMX 09T3 Indexable Inserts, 90° Shaft Diameter 25mm - Teknik Makina
Take advantage of a robust indexable‑insert solution that combines a 25 mm shank for high rigidity with a 60 mm cutting length and a 90° cutting angle for precise square‑shoulder machining; order the cutter via Metav Werkzeuge or consult the team for integration into production. Indexable‑insert shank cutter S802TM — 25 mm shank, 90° cutting angle, for WNMX 09T3 inserts (Teknik Makina) The Indexable‑insert shank cutter S802TM is a purpose‑built 90° milling body for WNMX 09T3 indexable inserts, offering a compact overall length and a rigid shank for stable machining in serial and jobbing environments 25 mm shank diameter for stable clamping Compatible with WNMX 09T3 indexable inserts 90° cutting angle for square shoulder milling Torx M3x7 clamp with T8 key for secure insert fit Rigidity and repeatable geometry for reliable milling results Built around a 25 mm shank that increases spindle stability, this milling body delivers consistent cutting geometry and reduces chatter during interrupted cuts. The design translates directly into measurable gains in surface finish and dimensional repeatability: the 90° cutting angle enables true square shoulders while the compact construction minimises overhang. For production runs where cycle times and part quality matter, the combination of a rigid shank and a precise cutting face supports higher feed rates and predictable tool life without compromising tolerances. Fast insert changes and predictable maintenance intervals The tool accepts WNMX 09T3 indexable inserts and is compatible with Korloy grades, allowing straightforward grade selection for specific materials. Insert retention is secured by a Torx M3x7 screw using a T8 key, which simplifies replacement and reduces downtime during tool changes. With a 60 mm cutting length, the body supports deeper engagements while keeping insert life manageable; the modular concept reduces consumable costs because worn inserts are replaced rather than the whole body, a pragmatic benefit for workshop and industrial procurement. Practical dimensions and handling for workshop integration With a 150 mm overall length and a diameter of 25 mm, the shank cutter balances reach and stiffness for common milling tasks that demand square shoulders and planing passes. The tool has two cutting edges, a weight of 0.563 kg, and a compact profile that fits typical toolholders; this keeps tool offsets predictable and reduces balancing requirements. Supplied and distributed via Metav Werkzeuge, the milling body benefits from local stock and logistics that support timely replenishment and professional after‑sales communication, reinforcing continuity in the machining process. For integration advice or to discuss the Teknik Cutting Tools S802TM’s suitability for a specific machining task, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 to arrange a technical consultation and delivery options. Technical Data Article number: S802TM Manufacturer: Teknik Makina Facts Diameter: 25 mm Shank diameter: 25 mm Cutting length: 60 mm Overall length: 150 mm Cutting edges: 2 Cutting angle: 90° Weight: 0.563 kg Torx screw: M3x7 Torx key: T8 Special features Compatible with WNMX 09T3 indexable inserts Compatible insert manufacturer: Korloy 90° cutting angle for square shoulder milling Torx clamp system for secure insert retention 25 mm shank for stable clamping FAQ Which inserts fit this cutter? The cutter is designed for WNMX 09T3 indexable inserts; Korloy grades are compatible and recommended according to machining needs when using the S802TM from Teknik Makina. What are the key dimensions of the tool? The S802TM has a 25 mm shank, 60 mm cutting length and 150 mm overall length; the tool weight is 0.563 kg and it features two cutting edges. For which machining tasks is this body best suited? The 90° cutting geometry makes the tool particularly suitable for square shoulder milling and similar operations requiring precise perpendicular faces. How are the inserts secured and replaced? Inserts are clamped with an M3x7 Torx screw; a T8 key is used for secure, repeatable fastening and quick replacement of worn inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For ADKT 1505 Indexable Inserts, 25mm Shank Diameter 2 Flutes - Teknik Makina
Taking advantage of a rigid 25 mm shank and compatibility with ADKT 1505 indexable inserts, this milling tool delivers stable cutting and quick insert changes for continuous production. Benefit from precise tool clamping, straightforward maintenance and expert advice — order the milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shaft-mounted milling cutter S312TM — 25 mm shank, for ADKT 1505 indexable inserts (Teknik Makina) The Shaft-mounted milling cutter S312TM is designed for shank-mounted milling operations using ADKT 1505 indexable inserts, offering a compact 150 mm overall length for versatile workshop use. 25 mm shank diameter for stable clamping Compatible with ADKT 1505 indexable inserts Two cutting edges for efficient material removal Supplied with M4x10 Torx screw and T15 key Stable shank design for precise machining The solid 25 mm shank and compact 150 mm overall length combine to reduce run-out and vibration during milling, which directly improves surface finish and dimensional consistency. A balanced configuration with two cutting edges ensures symmetric cutting forces, reducing chatter on standard toolholders and supporting consistent cycle times. The modest mass of 0.55 kg contributes to easier handling and rapid tool changes without compromising rigidity. Machine shops seeking repeatable results will value the combination of stable clamping and a short overhang for close-tolerance milling. Reliable insert system reduces downtime Designed for ADKT 1505 indexable inserts, the tool accepts widely available carbide inserts for fast replacement and predictable cutting performance. The insert pocket and secure fastening with the supplied M4x10 Torx screw (Torx key T15) make replacement straightforward and minimise downtime. Using established insert geometries means stocks of cutting grades from preferred manufacturers such as ISCAR can be used, so tooling inventory is easier to manage. The result is a pragmatic solution that supports steady production and simpler maintenance cycles. Easy maintenance and seamless workshop integration The straightforward construction and standard fastening hardware allow quick on-bench service and reduce the need for specialised tooling. Compatibility with common indexable inserts and a standard shank format simplifies integration into existing tool sets and reduces the number of adapters required. Focusing on functional reliability rather than cosmetic extras, this cutter is a practical component for mixed-production environments where changeover speed and predictable performance matter most. For dependable milling performance with a 25 mm shank, contact Metav Werkzeuge for personalised technical advice on the S312TM cutter from Teknik Makina — call +49 2822 7131930 or email info@metav-werkzeuge.com for further information and procurement support. Technical data SKU: S312TM Manufacturer: Teknik Makina Facts Shank diameter: 25 mm Cutting length: 60 mm Overall length: 150 mm Weight: 0.55 kg Diameter: 25 mm Cutting edges: 2 Special features Compatible with ADKT 1505 indexable inserts Compatible with ISCAR inserts Torx screw M4x10 included Torx key T15 included FAQ Which insert type is required for this cutter? The S312TM shaft-mounted milling cutter uses ADKT 1505 indexable inserts; compatible grades from ISCAR or other suppliers can be fitted. How is the insert secured to the cutter? Inserts for the S312TM are clamped with the supplied M4x10 Torx screw, tightened using the T15 key for secure seating. What are the shank and overall dimensions? This cutter features a 25 mm shank, a cutting length of 60 mm and an overall length of 150 mm. How many cutting edges does the tool have? The S312TM is supplied with two cutting edges, offering balanced cutting forces and efficient material removal. Is the tool compatible with inserts from major manufacturers? Yes, the cutter accepts ADKT 1505 inserts and is compatible with widely used insert suppliers such as ISCAR, facilitating stock commonality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For ADKT 1505 Indexable Inserts, 3 Flutes, 30mm Diameter - Teknik Makina
Take advantage of the combination of robust rigidity, simple insert change-out and precise geometry to maintain steady milling productivity; order the tool via Metav Werkzeuge or consult our specialists for application advice. S314TM shaft cutter by Teknik Makina – 30 mm diameter, for ADKT 1505 indexable inserts The S314TM shaft cutter is a purpose-built indexable-insert milling tool for productive CNC machining, designed to accept ADKT 1505 inserts and to deliver stable cutting performance in repeated operations 30 mm cutting diameter for stable milling Compatible with ADKT 1505 indexable inserts 25 mm shank diameter for secure clamping Three cutting edges for efficient material removal Predictable metal removal with compact, rigid design The S314TM is engineered to provide consistent cutting through a combination of a 30 mm nominal diameter and a 25 mm shank, yielding higher stiffness at the toolholder interface and reduced vibration during engagement. With a 50 mm cutting length and a 150 mm overall length, the cutter offers a balance between reach and rigidity that suits both short-stepped finishing and deeper shoulder milling operations. The three-flute layout improves radial balance and ensures steady chip load per tooth, which in turn supports stable cycle times and repeatable component quality across production batches. Fast indexable-insert handling for minimal downtime Tool change and maintenance have been simplified by the standardised clamping design: the indexable inserts are secured with an M4x10 Torx screw and adjusted using a T15 key, enabling quick insert replacement and reliable seat contact every time. Compatibility with ADKT 1505 grade plates—commonly supplied by manufacturers such as ISCAR—means spare parts are widely available and changeovers are straightforward. This reduces unproductive machine idle time, allowing production planners to maintain throughput without complex tool regrinds or reconditioning. Suited to productive CNC milling operations The cutter’s geometry, incorporating three cutting edges, supports efficient chip evacuation and balanced cutting forces, which contributes to a predictable surface finish and longer insert life when parameters are set correctly. The bodied construction and measured mass (approx. 0.596 kg) give a favourable dynamic response in typical milling spindles, while the indexable-insert system keeps per-edge costs low and consistent. For job shops and in-house production lines seeking to streamline tooling logistics, this design offers a pragmatic blend of performance, serviceability and inventory friendliness. Contact Metav Werkzeuge for availability of the Teknik Makina S314TM shaft cutter and tailored procurement advice from our Emmerich team Technical data Article number: S314TM Manufacturer: Teknik Makina Product type: Shaft cutter for indexable inserts Compatible inserts: ADKT 1505 Compatible insert manufacturer: ISCAR Torx screw: M4x10 Torx key: T15 Facts Diameter: 30 mm Cutting edges: 3 Shank diameter: 25 mm Cutting length: 50 mm Overall length: 150 mm Weight: 0.596 kg Special features For ADKT 1505 indexable inserts Compatible with ISCAR inserts M4x10 Torx clamping screw T15 Torx key interface SKU S314TM Brand: Teknik Makina FAQ Which inserts fit this cutter? The cutter accepts ADKT 1505 indexable inserts; compatible grades from established suppliers such as ISCAR are commonly used with the S314TM. How are the inserts secured and serviced? Inserts are clamped with an M4x10 Torx screw and can be tightened or released with a T15 key for rapid change-out and straightforward maintenance of the S314TM shaft cutter. What cutting profile and edge count does the tool offer? The tool is supplied with a 30 mm diameter and three cutting edges, optimised for balanced cutting forces and effective chip removal in indexable-insert milling. Is the cutter suitable for CNC production runs? Yes, the combination of a stiff 25 mm shank, standardised inserts and simple clamping makes the cutter well suited to repetitive CNC milling operations where quick insert changes and predictable performance are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For ADKT 1505 Indexable Inserts, 35mm Diameter 3 Flutes, 32mm Shank - Teknik Makina
Take advantage of proven rigidity and precise indexable-insert compatibility: the robust 32 mm shank and three cutting edges deliver stable cutting performance and consistent surface finish. Choose direct procurement through Metav Werkzeuge or consult the technical advisers for application support. S316TM Shank Cutter for ADKT 1505 Indexable Inserts — 35 mm cutting diameter, 32 mm shank The S316TM is a shank cutter engineered for industrial milling tasks with ADKT 1505 indexable inserts, offering a compact overall length for straightforward integration into production toolsets 35 mm cutting diameter 32 mm hardened shank for rigidity Compatible with ADKT 1505 inserts (ISCAR) Includes M4x10 Torx clamp screw, T15 key Greater stiffness for repeatable machining results With a 32 mm shank and a solid build weighing 0.92 kg, this cutter is designed to reduce chatter and improve stability in interrupted and continuous cuts. The presence of three cutting edges contributes to balanced cutting forces, which helps to achieve a more consistent surface finish and longer insert life. For operations where dimensional repeatability matters, the design reduces the need for rework and supports higher process reliability. Fast indexable-insert changes minimise downtime Compatibility with ADKT 1505 indexable inserts — including variants from ISCAR — allows quick tool servicing and straightforward spare-part management. The clamping system uses an M4x10 Torx screw and a T15 key for secure, repeatable fixation of the insert, enabling rapid changes without specialised fixtures. This combination lowers setup times and simplifies tool handling in busy workshop environments. Compact geometry for versatile milling tasks A 35 mm cutting diameter, 50 mm cutting length and a total length of 150 mm make this cutter suitable for both face and light peripheral milling in confined tool envelopes. The cutter’s proportions provide a compromise between reach and rigidity, making it appropriate for finishing and semi‑finishing operations where access and stability are both required. The specification supports a broad range of production tasks without overcomplicating tool inventory. Built for efficient workshop operation The tool’s straightforward specification supports efficient stockkeeping and predictable performance on the shop floor. As a tool designed for indexable inserts, it reduces consumable waste compared with solid tools and allows rapid recovery from wear by replacing only the inserts. Application advice and machining recommendations are available to assist selection and integration into existing toolholders and machine setups. Choose the Teknik Makina S316TM for stable, high‑precision milling with ADKT 1505 inserts — contact Metav Werkzeuge in Emmerich for tailored procurement and technical advice: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: S316TM Manufacturer: Teknik Makina Suitable for inserts: ADKT 1505 Compatible insert maker: ISCAR Torx screw: M4x10 Torx key: T15 Facts Shank diameter: 32 mm Cutting diameter: 35 mm Cutting length: 50 mm Overall length: 150 mm Cutting edges: 3 Weight: 0.92 kg Special features For ADKT 1505 indexable inserts Compatible with ISCAR inserts M4x10 Torx clamp screw included T15 Torx key included SKU: S316TM FAQ Which inserts are compatible with this cutter? The cutter is designed for ADKT 1505 indexable inserts; variants from ISCAR are compatible and commonly used with this tool. What are the main dimensions to check for machine integration? Key dimensions are a 35 mm cutting diameter, 50 mm cutting length, 32 mm shank diameter and a 150 mm overall length. Is the clamp screw supplied with the cutter? Yes, the cutter comes with an M4x10 Torx clamp screw and the matching T15 key for insert securement. What milling tasks suit this cutter best? The tool is suitable for face and light peripheral milling where a compact overall length and good stability are required. How much does the cutter weigh and why does that matter? The cutter weighs 0.92 kg; the mass contributes to cutting stability and helps to dampen vibration during operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For APKT 1705 Indexable Inserts, 25mm Shank Diameter - Teknik Makina
Benefit from a compact, high-stability milling solution: the robust 25 mm shank and generous 60 mm cutting length combine to deliver steady chip evacuation and longer engagement per tool change. Compatibility with APKT 1705 indexable inserts keeps tooling costs predictable and replacement rapid via Metav Werkzeuge. Shaft cutter for APKT 1705 indexable inserts — 25 mm shank, 60 mm cutting length (Teknik Cutting Tools) A shaft cutter designed for grooved and face milling operations, optimised for use with APKT 1705 indexable inserts and suited to production environments requiring stable clamping and repeatable geometry. 25 mm shank for solid toolholders 60 mm cutting length for deep engagements Compatible with APKT 1705 inserts (Taegutec) Secure Torx M4x10 fixing, key T15 Consistent cutting performance for reliable production A stable toolholder is the foundation of predictable machining. The combination of a 25 mm shank and balanced mass provides reduced runout and improved rigidity, which translates directly into consistent finish and tool life. The cutter is configured with two cutting edges, enabling steady material removal while limiting vibration. The clamping interface is secured by an M4x10 Torx screw tightened with a T15 key, ensuring the insert pocket maintains alignment across repeated indexings. This mechanical certainty reduces scrap rates and supports lean production processes by keeping process variability low. Compatibility that reduces downtime and simplifies logistics The tool is engineered specifically for APKT 1705 indexable inserts from Taegutec, allowing rapid insert exchange without special adapters. Using a standard insert family means fewer stock items and faster turnaround when replacing worn edges, which improves overall equipment effectiveness. The shaft cutter’s design permits straightforward insert seating and a compact cutting head geometry that helps to maintain chip flow during longer engagements. For workshops consolidating tooling ranges, this configuration helps to standardise consumables and simplifies purchasing and storage logistics. Durable handling and predictable integration into production lines At an overall length of 150 mm and a weight of 0.534 kg, the cutter balances accessibility in tight set-ups with sufficient overhang for deeper cuts while keeping deflection low. The 60 mm cutting length offers extended engagement for profiling and shoulder milling, while the solid shank design supports steady clamping in standard toolholders. Sourced from Teknik Cutting Tools and distributed through Metav Werkzeuge, the component benefits from a pragmatic supply chain: stocked and quality-filtered in Emmerich for dependable delivery to European workshops. That supply reliability, combined with straightforward maintenance, supports sustained uptime and long-term process planning. For application advice or to reserve the Teknik Cutting Tools S660TM with its 25 mm shank and 60 mm cutting length, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for fast, expert support Technical data Article number: S660TM Manufacturer: Teknik Makina Compatible inserts: APKT 1705 (Taegutec) Facts Shank diameter: 25 mm Cutting length: 60 mm Cutting edges: 2 Overall length: 150 mm Weight: 0.534 kg Special features Torx screw: M4x10 Torx key: T15 Compatibility: for APKT 1705 indexable inserts Manufacturer series: Teknik Cutting Tools FAQ Which indexable inserts fit this cutter? The cutter accepts APKT 1705 indexable inserts; compatibility is specified for the Taegutec variant and identical APKT 1705 formats. How is the insert secured in the cutter? Insert clamping is achieved with an M4x10 Torx screw; a T15 key is used for tightening and repeatable clamping torque. What is the shank diameter and why does it matter? The 25 mm shank provides enhanced rigidity compared with smaller diameters, reducing deflection and improving surface finish during prolonged engagements. How long is the effective cutting length? The tool offers a 60 mm cutting length, suitable for deeper facing and profiling operations while maintaining process stability. What is the article number for ordering or reference? Reference the SKU S660TM when enquiring or ordering; the component is supplied by Teknik Cutting Tools and distributed via Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For APXT 1003 Indexable Inserts, 90° Cutting Angle - Teknik Makina
Take advantage of the combination of high clamping rigidity, long cutting reach and simple insert handling for steady production performance; order the S180TM directly via Metav Werkzeuge or ask our consultants for tailored advice. S180TM Shank Milling Cutter — 25 mm shank, 60 mm cutting length A robust S180TM Shank Milling Cutter for versatile indexable-insert milling with APXT 1003 inserts, engineered for secure clamping and efficient shoulder work Shank Ø 25 mm for secure clamping 60 mm cutting length for deeper passes Compatible with APXT 1003 indexable inserts Torx M2.5×5.5 screw and T8 key included Consistent rigidity for repeatable cuts The tool's 25 mm shank and well balanced 150 mm overall length produce reliable clamping stability, which reduces chatter and maintains dimensional accuracy during longer cuts. With a 90° cutting angle, the geometry is tailored to shoulder and face milling operations that demand sharp 90-degree shoulders. The increased rigidity directly improves process reliability, meaning fewer part rejects and less time lost to rework — a measurable benefit for batch production and industrial environments. Extended reach that expands capability Featuring a 60 mm cutting length, this cutter allows deeper engagement without immediate overhang compromise. The longer cutting reach can reduce the need for multiple setups when profiling deeper features, thereby shortening cycle times. Combined with three precision edges, the design supports steady material removal rates while preserving tool life, a rational advantage for shops aiming to increase throughput with minimal fixture changes. Fast insert changes and secure fastening Designed for APXT 1003 indexable inserts and compatible with Korloy variants, the system simplifies insert replacement. The supplied Torx M2.5×5.5 screw and T8 key provide secure clamping of the insert pocket, allowing quick, repeatable tool service without special adapters. Faster changeovers translate into less machine downtime and improved overall equipment effectiveness (OEE), a practical gain for production-focused workshops. Practical fit for everyday machining tasks This cutter's three cutting edges and a compact mass of 0.563 kg contribute to predictable dynamic behaviour in milling spindles. Suitable for general-purpose milling tasks where a sturdy interface and standardised inserts are preferred, the tool supports familiar workflows and reduces the need for bespoke tooling. The combination of tried-and-tested insert standards and a straightforward shank design makes it a pragmatic choice for both maintenance shops and production lines. For high-rigidity, insert-based milling from Teknik Makina, contact Metav Werkzeuge to discuss the S180TM and secure tailored advice or ordering support from our specialists at Metav Werkzeuge. Technical data Article number: S180TM Manufacturer: Teknik Cutting Tools Facts Shank diameter: 25 mm Cutting length: 60 mm Overall length: 150 mm Number of cutting edges: 3 Weight: 0.563 kg Cutting angle: 90° Torx screw: M2.5×5.5 Torx key: T8 Special features For APXT 1003 indexable inserts Compatible with Korloy insert variants Designed for secure clamping stability Three cutting edges for balanced wear FAQ Which inserts fit this cutter? The S180TM is designed for APXT 1003 indexable inserts and is compatible with Korloy-manufactured variants that follow the same APXT 1003 specification. What are the critical dimensions to check for machine compatibility? Check the 25 mm shank diameter and the 150 mm overall length of the S180TM; these determine whether the cutter fits the spindle and provides the required reach for the application. Is a fastening tool supplied with the cutter? Yes. The S180TM is supplied with a Torx M2.5×5.5 screw and a T8 key for secure insert clamping and straightforward insert changes. How many cutting edges does the tool have and why does that matter? The cutter has three cutting edges, which helps distribute wear and provides a balance between cutting stability and efficient material removal for general milling tasks. What kind of milling operations suit this tool best? With a 90° cutting angle and a long cutting length, the tool is well suited to shoulder and face milling where square shoulders and deeper passes are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For AXMT 0602 And APKT 0903 Indexable Inserts, 2 Flutes, 16mm Shank - Teknik Makina
Benefit from a precise, shank-mounted milling solution with a 16 mm shank and 50 mm cutting length, designed for reliable indexable insert machining with AXMT 0602 and APKT 0903 inserts; order the S020TM directly via Metav Werkzeuge or ask our consultants for tailored tooling support. Shank-mounted milling cutter S020TM — 16 mm shank, for AXMT 0602 and APKT 0903 inserts by Teknik Makina A sturdy Shank-mounted milling cutter S020TM engineered for indexable insert milling in general machining and production settings, compatible with AXMT 0602 and APKT 0903 insert families. 16 mm shank diameter 50 mm cutting length Compatible with APKT 0903 inserts Torx screw M2.5×5.5 fastening Consistent machining performance for repeatable production The S020TM delivers stable cutting through its two-cut geometry and precisely defined shank form. The two cutting edges reduce vibration and allow for predictable chip formation, which improves surface finish and extends insert life. In practice this means fewer tool changes and a more consistent cycle time on batch runs; the reduced variation supports quality control in both small-series and larger production environments. Compatibility and ease of maintenance to reduce downtime Designed for use with standard indexable inserts, the cutter accepts AXMT 0602 and APKT 0903 insert types and is compatible with inserts from Taegutec, enabling flexible selection of grades for different materials. Fastening is by a M2.5×5.5 Torx screw, operated with a T8 key, so insert replacement is straightforward and requires only common workshop tools. The clear, standardised fixing reduces maintenance time and keeps the tool in service for longer. Practical dimensions and workshop integration With a 16 mm shank diameter, 50 mm of cutting length and an overall length of 150 mm, the tool integrates easily into compact toolholders while providing sufficient reach for many slotting and shoulder-milling operations. The modest mass of 0.233 kg supports high-speed rotation without excessive imbalance when clamped correctly. These dimensions make the tool suitable for production benches where tool rigidity and accessibility are priorities. Why this cutter benefits production workflows By combining established insert systems with a robust shank design, the S020TM supports economical machining: predictable insert wear, straightforward insert sourcing, and rapid replacement. The design emphasises efficiency and process stability, helping to shorten setup time and reduce machining variability — factors that translate directly into improved output quality and lower per-part costs over time. For reliable, indexable-insert milling select the Teknik Makina S020TM with its 16 mm shank and 50 mm cutting length — contact Metav Werkzeuge for ordering or expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: S020TM Manufacturer: Teknik Makina Facts Shank diameter: 16 mm Cutting length: 50 mm Overall length: 150 mm Diameter: 16 mm Number of cutting edges: 2 Weight: 0.233 kg Special features Compatible inserts: AXMT 0602, APKT 0903 Compatible insert manufacturer: Taegutec Torx screw: M2.5×5.5 Torx key size: T8 Intended for indexable insert milling FAQ Which insert types fit this milling cutter? The S020TM accepts AXMT 0602 and APKT 0903 indexable inserts; Taegutec grades are indicated as compatible for varied workpiece materials. What is the shank size and overall length? Shank diameter is 16 mm and the overall length is 150 mm for the S020TM, making it suitable for standard 16 mm toolholders and many fixture arrangements. How many cutting edges does the tool have and what is the benefit? The tool features two cutting edges; this geometry enhances stability and chip control, improving surface finish and consistent insert wear. Which fastening hardware is used for inserts? Inserts are secured with a Torx screw in size M2.5×5.5, tightened using a T8 key for quick and reliable insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Shank Cutter for BLMP 0603 Indexable Inserts With Internal Coolant, 17mm Diameter - Teknik Makina
Benefit from the combination of internal coolant, a 17 mm shank and a 40 mm cutting length for reliable milling and improved tool life; precise clamping and straightforward insert replacement keep production running smoothly. Order the cutter directly via Metav Werkzeuge or consult our specialists for application-specific advice. Shank cutter S478-1TM – for BLMP 0603 indexable inserts, 17 mm shank, internal coolant (Teknik Makina) The Shank cutter S478-1TM is a shank-mounted indexable insert cutter engineered for use with BLMP 0603 inserts, offering coolant-through delivery for improved chip evacuation and consistent machining performance. 17 mm shank diameter Coolant-through design Compatible with Taegutec BLMP 0603 inserts 150 mm overall length Improved tool life and process reliability through coolant-through delivery The built-in internal coolant channel directs coolant straight to the cutting zone, reducing heat at the insert edge and aiding chip control. This results in longer insert life and more consistent surface finish, especially in medium to heavy milling operations. The coolant-through concept also lowers the risk of built-up edge and makes evacuation more effective where chip pockets can otherwise hinder performance. For workshops seeking stable cycle times, the coolant provision is a clear operational advantage. Stable clamping and accurate cutting for repeatable results With a 17 mm shank and a 16 mm shaft diameter, the tool provides secure clamping and high torsional rigidity. The 40 mm cutting length balances reach and stiffness, while the two cutting edges support efficient material removal with predictable chip loads. These dimensional choices reduce vibration and contribute to repeatable tolerances across series production. Where programme reliability and toolholder stability are priorities, this configuration helps maintain process control. Compatibility and service-friendly design for quick maintenance Designed for the BLMP 0603 indexable insert family and compatible with Taegutec insert geometries, the cutter simplifies tooling logistics when that insert system is already standard in the shop. Insert retention uses an M3x6.2 Torx screw tightened with a T8 Torx key, enabling rapid insert changes and secure seating. The combination of standard insert format and familiar fastening reduces downtime during servicing and makes replacement straightforward for trained staff. Choose the Teknik Makina shank cutter with coolant-through delivery from Metav Werkzeuge for dependable supply and practical technical guidance—contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for precise application support and fast delivery. Technical data SKU: S478-1TM Manufacturer: Teknik Makina Product type: Shank cutter Designation: for BLMP 0603 indexable inserts Core data Diameter: 17 mm Shank diameter: 16 mm Overall length: 150 mm Cutting length: 40 mm Weight: 0.244 kg Cutting edges: 2 Torx screw: M3x6.2 Torx key: T8 Special features Internal coolant (coolant-through) For BLMP 0603 indexable inserts Compatible with Taegutec insert geometry FAQ Is this cutter compatible with BLMP 0603 inserts? Yes. The shank cutter S478-1TM is designed for BLMP 0603 indexable inserts and matches the insert seat geometry. How does the internal coolant affect machining? Internal coolant supplies coolant directly to the cutting edge, improving chip evacuation, reducing temperature at the cutting zone, and extending insert life for the S478-1TM. Which tool is required to change the inserts? Insert retention on the S478-1TM uses an M3x6.2 Torx screw; a T8 Torx key is used for tightening and loosening. What are the key dimensions for clamping and reach? Key dimensions are a 17 mm cutter diameter, a 16 mm shank diameter and a 150 mm overall length with a 40 mm cutting length. What is the SKU for ordering or reference? The product is listed as SKU S478-1TM from Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter for BLMP 0603 Indexable Inserts, 3 Flutes, 40mm Cutting Length - Teknik Makina
Benefit from a stable milling solution that combines a 20 mm shank, 40 mm cutting length and secure Torx fastening for reliable indexable-insert performance; order the cutter directly via Metav Werkzeuge or request advice from our consultants. Shaft milling cutter S481TM by Teknik Makina — compatible with BLMP 0603 indexable inserts, 20 mm shank, 3 cutting edges Shaft milling cutter S481TM designed for indexable-insert milling applications; suited to production environments where quick insert changes and consistent cutting geometry are required 20 mm shank diameter 40 mm cutting length Compatible with BLMP 0603 inserts Torx M3x6,5 fastening Reliable indexable-insert performance for small-format milling The design focuses on consistent cutting results by using standard indexable geometry. With BLMP 0603 compatibility and 3 cutting edges, the tool enables repeatable insert indexing and predictable wear patterns. This reduces set-up time and simplifies inventory management because the insert size and form are widely available. The tool body supports secure insert clamping, which preserves cutting geometry during interrupted cuts and reduces vibration-related deviations. Rigidity and repeatability from a compact shank design A 20 mm shank provides a balance between rigidity and accessibility for many milling setups. The combination of a substantial shank diameter and a moderate overall length (150 mm) reduces deflection during axial and radial loading, improving dimensional accuracy on each component. For process planners this means fewer rework cycles and better cycle-time reliability when the cutter is used in repetitive milling tasks on production equipment. Service-friendly fastening to speed insert replacement Maintenance is simplified by the secure Torx fastening: M3x6,5 screw with a T8 key interface. The fastening design permits quick insert changes while maintaining repeatable clamp force and seat alignment, so downtime for tool changes is minimised. Fewer handling steps also reduce the risk of incorrect seating; the clear mechanical interface supports safe, efficient shop-floor practice without the need for special tools beyond the supplied Torx size. Practical fit for industrial milling workflows This indexable-insert cutter fits into established tooling systems where BLMP 0603 inserts and Taegutec-compatible parts are used, enabling fast reconditioning of cutting edges without replacing the whole cutter body. The modest weight (0.335 kg) and defined cutting length help when planning tool offsets and fixture clearances, allowing machinists and process engineers to integrate the cutter into existing tool libraries with minimal adjustments. The straightforward geometry supports predictable tool life and easy documentation in tool management systems. For procurement or technical advice on the Teknik Makina shaft milling cutter S481TM, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and delivery options. Technical data Article number: S481TM Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Cutting length: 40 mm Overall length: 150 mm Cutting edges: 3 Weight: 0.335 kg Special features For indexable inserts BLMP 0603 Compatible insert manufacturer: Taegutec Torx screw: M3x6,5 Torx key: T8 SKU: S481TM Brand: Teknik Makina FAQ What inserts does the cutter accept? The shaft milling cutter S481TM accepts BLMP 0603 indexable inserts and is specified as compatible with Taegutec insert versions. How is the insert secured on the cutter? Insert clamping is performed with a Torx screw (M3x6,5); the designated key size is T8 for repeatable fastening and straightforward replacement. What are the key dimensions to consider when fitting the tool? Important dimensions include the 20 mm shank diameter, 40 mm cutting length and overall length of 150 mm for planning tool offsets and fixture clearance when using the S481TM. Is this cutter suitable for high-volume production? The design of the S481TM supports quick insert changes and consistent clamping force, which helps maintain uptime and repeatability in production settings where BLMP 0603 inserts are standard. Which manufacturer produced this tool? The S481TM is produced by Teknik Makina and distributed via Metav Werkzeuge; the SKU is S481TM for ordering and inventory purposes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For BOMT 1304 Indexable Inserts, 2 Flutes, 40mm Cutting Length - Teknik Makina
Robust 20 mm shank and compatibility with BOMT 1304 indexable inserts deliver stable, accurate milling; the two‑flute geometry and 40 mm cutting length enable efficient chip evacuation and reduced cycle times. Order the S851TM directly via Metav Werkzeuge or ask our consultants if needed. S851TM Shank Milling Cutter — 20 mm shank, for BOMT 1304 indexable inserts (Teknik Makina) The S851TM is a precision shank milling cutter engineered for industrial milling applications using BOMT 1304 indexable inserts; designed to combine secure clamping with efficient material removal in demanding production environments. 20 mm shank diameter for stable clamping Compatible with BOMT 1304 indexable inserts Two-flute design for efficient chip removal 150 mm overall length, 40 mm cutting length Heavy-duty clamping for consistent results A 20 mm shank delivers the stiffness required for repeatable machining, reducing runout and vibration during milling operations. The robust shank diameter contributes to stable clamping, which in turn improves the surface finish and extends insert life. For workshops that prioritise process reliability, the combination of dimensional stability and controlled tool weight supports consistent part quality across long production runs without frequent re‑adjustment. Faster machining through optimised cutting geometry With a two‑flute geometry and 40 mm cutting length, the tool is optimised for productive chip evacuation and sustained cutting performance. The reduced flute count enhances chip flow, which helps maintain cutting temperatures and avoids clogging in pockets or deep cuts. This geometry supports higher material removal rates where insert indexability and quick replacement minimise downtime and keep cycle times competitive. Simple insert fixation and low-maintenance operation Insert changes are fast and secure thanks to the M3.5x8.5 Torx screw with a T10 key interface, supplying a compact and reliable clamping solution. The cutter accepts BOMT 1304 type indexable inserts and is specified to work with Ingersoll‑type inserts, allowing familiar spare parts logistics for established setups. Less time spent on insert handling means more machine availability and predictable maintenance intervals. Designed for integration into production workflows At 150 mm overall length and a tool mass of 0.356 kg, the cutter balances reach and rigidity for a broad range of milling tasks. The design supports straight insertion into standard tool holders and straightforward handling on the shop floor. Clear technical matching with typical indexable insert systems reduces specification errors when integrating the tool into CAM lists or tooling inventories, making procurement and tool management more efficient. For application guidance or to secure supply of the Teknik Cutting Tools S851TM from Metav Werkzeuge — delivered from Emmerich with full product support — contact our sales team at info@metav-werkzeuge.com or call +49 2822 7131930 to confirm suitability for the intended process. Technical data Article number: S851TM Manufacturer: Teknik Makina Name: Schaftfräser for BOMT 1304 Indexable Inserts Compatible inserts: BOMT 1304 Compatible insert manufacturer: Ingersoll Torx screw: M3,5x8,5 Torx key: T10 Facts Shank diameter: 20 mm Cutting length: 40 mm Overall length: 150 mm Flutes: 2 Diameter: 20 mm Weight: 0.356 kg Special features For BOMT 1304 indexable inserts Compatible with Ingersoll inserts M3.5x8.5 Torx screw, T10 key SKU: S851TM FAQ Which inserts are compatible with this cutter? The cutter accepts BOMT 1304 indexable inserts; it is specified as compatible with Ingersoll‑type inserts for the S851TM. What are the key dimensions of the tool? Key data for the S851TM: 20 mm shank diameter, 40 mm cutting length, 150 mm overall length, 2 flutes, weight 0.356 kg. How are inserts secured in the cutter? Inserts are clamped with an M3.5x8.5 Torx screw tightened using a T10 key for reliable fixation and quick replacement. Can the screw type be replaced with a different standard? The S851TM is specified for an M3.5x8.5 Torx screw; replacement with another standard is possible if the replacement matches the cutter pocket and torque specifications, but original Torx fasteners are recommended. Is the tool suitable for automated tool magazines? The tool’s dimensions and shank design are compatible with standard tool holders and automated magazines where a 20 mm shank is acceptable for the machine’s tooling system. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For BOMT 1304 Indexable Inserts, 3 Cutting Edges, 40mm Cutting Length - Teknik Makina
Take advantage of a 25 mm shank and compatibility with BOMT 1304 indexable inserts to achieve stable, flexible milling with a 40 mm effective cutting length; order the S853TM shank milling cutter directly via Metav Werkzeuge or ask the consultants for integration advice. S853TM shank milling cutter – 25 mm shank, for BOMT 1304 indexable inserts (Teknik Makina) A robust S853TM shank milling cutter engineered for indexable BOMT 1304 inserts, designed to deliver consistent material removal and reliable performance in industrial milling applications. Fits BOMT 1304 indexable inserts (Ingersoll compatible) 25 mm shank diameter for stable toolholding 40 mm effective cutting length for deeper passes Three cutting edges for balanced milling performance Consistent machining through a stable shank design The predominantly mechanical advantage of a 25 mm shank is increased torsional stiffness and reduced runout, which supports stable clamping and predictable tool life. With a balanced geometry and three cutting edges, the cutter reduces vibrations during high-speed rotation, translating into improved surface finish and reduced rework. For production environments where cycle times and reproducible tolerances matter, this shank arrangement ensures fewer scrap parts and more consistent throughput. Flexible insert system lowers tooling complexity Compatibility with BOMT 1304 indexable inserts and Ingersoll-compatible plates allows a single cutter body to cover a variety of cutting conditions without swapping complete tools. The 40 mm effective cutting length provides scope for deeper axial engagement, enabling longer cuts per pass and fewer repositionings. The indexable system also separates cutting geometry from the tool body: worn edges are replaced quickly, meaning downtime is reduced and spindle utilisation is increased — a clear efficiency gain for batch and job-shop operations. Quick serviceability and predictable integration Assembly and maintenance rely on standardised fastening: an M1.8x4 Torx screw secured with a T10 key delivers repeatable clamp force for each insert change. The 150 mm overall length and a measured weight of 0.556 kg simplify balance calculations for holders and spindles, while the clear numeric data supports process planning and fixture selection. The combination of straightforward insert replacement and established fastening technology keeps maintenance intervals short and integration into existing toolsets uncomplicated. For tailored application advice or to confirm compatibility with specific holders and machines, contact Metav Werkzeuge — our technical team can advise on integration of the Teknik Cutting Tools S853TM shank milling cutter and BOMT 1304 inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss requirements. Technical Data Article number: S853TM Manufacturer: Teknik Makina Product: Shank milling cutter for BOMT 1304 indexable inserts Core data Shank diameter: 25 mm Cutting length (shank): 40 mm Overall length: 150 mm Number of cutting edges: 3 Weight: 0.556 kg Diameter: 25 mm Features Compatible with BOMT 1304 indexable inserts Torx screw: M1.8x4 Torx key size: T10 Compatible with Ingersoll inserts SKU: S853TM FAQ Which inserts fit this cutter? The S853TM is designed for BOMT 1304 indexable inserts and is compatible with Ingersoll-style plates for straightforward replacement. What shank diameter and overall length should be specified for holders? Shank diameter is 25 mm and overall length is 150 mm for the S853TM, suitable for many standard toolholders that accept a 25 mm shank. What fastening hardware secures the inserts? Insert clamping uses an M1.8x4 Torx screw tightened with a T10 key; this standard arrangement ensures repeatable clamp force for the S853TM. Can this cutter be used for deeper axial cuts? With a 40 mm effective cutting length and three cutting edges, the S853TM supports deeper passes while maintaining balanced cutting behaviour. What are the weight and balance considerations for spindle setup? Weight is 0.556 kg for the S853TM, a value useful for balancing and selecting compatible holders for stable machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For ENMX 0604 Indexable Inserts, 2 Flutes, 16mm Shank - Teknik Makina
Benefit from precise insert compatibility and a rigid shank: the S107TM accepts ENMX 0604 indexable inserts, offers a shank Ø16 mm for secure clamping and a Ø17 mm cutter diameter for stable milling. Order the S107TM directly via Metav Werkzeuge or ask our consultants if needed. Schaftfräser – insert milling cutter for ENMX 0604, Ø17 mm, shank Ø16 mm (Teknik Makina) The Schaftfräser is a shank-mounted insert milling cutter designed for indexable milling with ENMX 0604 inserts, suitable for machine shops and production environments requiring quick insert changes and consistent cutting geometry Insert milling cutter for ENMX 0604 Shank Ø16 mm for secure clamping Cutter Ø17 mm, overall length 150 mm Fast insert change with Torx M2.5x7 Precise performance through insert compatibility and rigid shank The S107TM is engineered as an insert milling cutter that accepts ENMX 0604 indexable inserts, delivering reliable machining cycles with minimal downtime. The combination of a shank Ø16 mm and a Ø17 mm cutting head provides improved concentricity and lower runout compared with loose-fixture solutions, which translates into steadier feeds and a consistent surface finish. Because the cutter is designed for indexable inserts, the cost per cutting edge is reduced and changeover is rapid, enabling efficient batch production without sacrificing repeatability. Workshop-friendly handling and maintenance for smooth workflows Maintenance and insert replacement are straightforward: the cutter uses Torx M2.5x7 fastening screws accessed with a T8 key, allowing quick, repeatable clamping of ENMX 0604 inserts from common manufacturers such as YG-1. This practical design shortens tool change time and reduces the risk of incorrect torque or seating during service intervals. The modular nature of the tool body supports straightforward inventory management: keep a stock of inserts rather than multiple full cutters to lower holding costs and simplify replenishment. Application guidance and fitment details for reliable results This shank-mounted cutter is intended for general-purpose milling with indexable inserts sized ENMX 0604; it features two cutting edges that balance chip evacuation and engagement for many milling tasks. The overall length of 150 mm pairs well with medium-reach tooling setups while the shank Ø16 mm supports rigid clamping in standard collets or toolholders. For optimal outcomes, pair the S107TM with recommended inserts and machining parameters provided by the insert manufacturer to match material and surface finish targets. For dependable insert milling with Teknik Cutting Tools' design, contact Metav Werkzeuge in Emmerich to secure the S107TM and discuss suitable ENMX 0604 inserts at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S107TM Manufacturer: Teknik Makina For inserts: ENMX 0604 Compatible insert maker: YG-1 Torx screw: M2,5x7 Torx key: T8 Shank diameter: 16 mm Cutter diameter: 17 mm Overall length: 150 mm Cutting edges: 2 FAQ What insert type does this cutter use? The S107TM is made for ENMX 0604 indexable inserts and is specified for that insert geometry. Which screw and key are required to change inserts? Insert fastening on the S107TM is with Torx M2.5x7 screws and a T8 key for secure and repeatable clamping. Is the cutter compatible with inserts from YG-1? Yes, the S107TM is compatible with YG-1 inserts sized ENMX 0604, as listed in the technical details. What are the main dimensions to check for machine setup? Key dimensions for setup are shank diameter 16 mm, cutter diameter 17 mm, and overall length 150 mm; these determine holder fit and reach. How many cutting edges does the tool have and what does that mean for machining? The tool has two cutting edges, which offers a balance between chip load per tooth and surface finish suitable for many milling tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For ENMX 0604 Indexable Inserts, 3 Flutes, 21mm Diameter, 150mm Overall - Teknik Makina
Take advantage of a compact, indexable solution that combines secure Torx fastening with a stable triple-edge geometry for consistent results in series production. The cutter’s 21 mm diameter and 20 mm shank offer straightforward integration into standard tool holders, while compatibility with ENMX 0604 inserts reduces tooling complexity — order directly via Metav Werkzeuge or contact the sales team for specification advice. Shaft-mounted milling cutter S110TM — indexable-insert milling cutter, Ø 21 mm, shank Ø 20 mm (Teknik Makina) The Shaft-mounted milling cutter S110TM is engineered for industrial milling operations using ENMX 0604 indexable inserts; it is intended for installations requiring a compact diameter with extended reach and secure Torx clamping Compatible with ENMX 0604 inserts 21 mm cutting diameter, 20 mm shank 150 mm overall length for extended reach Triple-edge design for increased stability Consistent compatibility reduces inventory complexity The cutter is designed around the ENMX 0604 indexable insert standard, which streamlines spare-part management and tool changes. Matching inserts from YG-1 make replacement predictable and economical, while the indexable design separates cutting geometry from the body so that only the insert needs renewal. This approach lowers operating expenditure and shortens machine downtime compared with solid-tool replacements, offering a clearer total-cost-of-ownership picture for production planning. Geometry and fastening for stable cutting performance A triple-cutting-edge configuration with a compact 21 mm diameter combined with a 20 mm shank gives the tool inherent rigidity during axial and radial engagement. The insert is secured with a Torx screw (specified M2.5x7) and tightened using a T8 key, which together provide reliable clamp force and repeatable seating of the insert. The result is reduced vibration, improved surface finish and predictable tool life — all relevant when cycle-time and surface integrity are priorities. Reach and accessibility for versatile set-ups With an overall length of 150 mm, the cutter is suited to operations that demand additional reach without resorting to oversize tooling. The extended length enables machining in deeper cavities or across wider faces while maintaining acceptable stiffness for light to medium material removal tasks. The combination of compact diameter and extended reach supports flexible fixturing and multi-operation sequences on a single spindle set-up. Workshop integration and serviceability The design supports straightforward maintenance: standardised insert geometry and Torx fastening simplify spare parts provisioning and routine servicing. The shank diameter and overall dimensions align with common holder standards, enabling quick toolholder changes and minimal set-up time in mixed-production environments. For procurement and workshop supply, Metav’s distribution and technical filter for the European market can assist with matching inserts and ensuring continuity of supply. Contact Metav Werkzeuge for precise compatibility checks and stock information on the S110TM — expert advice and reliable delivery from Emmerich is available via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S110TM Product name: Shaft-mounted milling cutter for ENMX 0604 indexable inserts Manufacturer: Teknik Makina Facts Diameter: 21 mm Shank diameter: 20 mm Overall length: 150 mm Cutting edges: 3 Torx screw: M2.5x7 Torx key size: T8 Special features For ENMX 0604 indexable inserts Compatible with YG-1 inserts Indexable-insert system for economical reconditioning FAQ Which insert type fits this cutter? The S110TM accepts ENMX 0604 indexable inserts; compatibility with YG-1 inserts is indicated in the technical data. What are the key dimensions to check for toolholder compatibility? Relevant dimensions are the 21 mm cutting diameter and 20 mm shank diameter; the overall length is 150 mm for reach considerations. How is the insert secured? Insert clamping is specified with a Torx screw (M2.5x7) and requires a T8 key for tightening and removal. How many cutting edges does the cutter have and what is the effect? The cutter features 3 cutting edges, a geometry that balances chip evacuation with axial stability for consistent surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Shank Cutter For ENMX 0604 Indexable Inserts, 5 Flutes, 32mm Diameter - Teknik Makina
Take advantage of a robust indexable-insert milling body with a 32 mm shank and five cutting edges for steady material removal and predictable tool life; order the tooling directly via Metav Werkzeuge or consult the technical team for application support. Shaft milling cutter S114TM — indexable-insert milling body, 32 mm shank, 5 cutting edges (Teknik Makina) A Shaft milling cutter S114TM engineered as an indexable-insert milling body for light to medium milling tasks, designed to accept ENMX 0604 inserts and to work with common workshop toolholders. Compatible with ENMX 0604 inserts 32 mm shank for secure clamping Five cutting edges for increased productivity M2.5x7 Torx screws, T8 key included Stable engagement and predictable cutting performance The cutter body is built around a 32 mm shank, providing a rigid interface with standard toolholders to reduce vibration and improve surface finish. With an overall length of 150 mm, the design balances reach and stiffness to maintain repeatable results in serial milling. The arrangement of five cutting edges distributes cutting forces and allows for consistent chip removal, which leads to longer service intervals and fewer interruptions in production. These characteristics contribute directly to higher process reliability and measurable productivity gains. Easy maintenance and fast insert changes for minimal downtime Compatibility with ENMX 0604 indexable inserts and the use of M2.5x7 Torx screws (drive size T8) simplifies service routines at the bench. The insert pocket and clamping geometry permit quick replacement of worn inserts, reducing machine idle time and tooling handling. A well-structured insert system, paired with the cutter body, ensures that the capital invested in inserts is turned into usable cutting life with minimal setup overhead — a cost-efficient approach for repetitive milling operations. Broad workshop compatibility and application flexibility The milling body accepts inserts from established suppliers such as YG-1, enabling selection of grades and geometries suited to aluminium, steels or hardened materials where appropriate. The tool functions as an indexable-insert milling body that can be integrated into typical CNC and manual machining workflows, supporting both production and maintenance environments. Clear mechanical features and standardised fastenings mean the tool is straightforward to spec into existing tool lists and procurement processes, ensuring rapid deployment across multiple machines. Contact Metav Werkzeuge for tailored technical advice and ordering of the Teknik Makina S114TM milling body; technical queries by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: S114TM Manufacturer: Teknik Makina EAN / classification: eClass 21180806, ETIM EC011860 Facts Shank / clamping diameter: 32 mm Overall length: 150 mm Number of cutting edges: 5 Insert type: ENMX 0604 Recommended insert supplier: YG-1 Torx screw: M2.5x7 Torx key: T8 Special features Indexable-insert milling body Standardised Torx clamping system Suitable for light to medium milling Designed for quick insert replacement FAQ What insert type fits this milling body? The S114TM accepts ENMX 0604 indexable inserts, allowing selection of grades and geometries compatible with the cutter body. Is a specific insert supplier required? The milling body is compatible with inserts from YG-1 and other manufacturers that provide ENMX 0604 inserts; material and grade selection depend on the machined material. What are the key dimensions for machine setup? Critical dimensions are a 32 mm shank for toolholder clamping and 150 mm overall length, with five cutting edges for load distribution. Which screw and key are used for insert clamping? Insert clamping uses an M2.5x7 Torx screw and a T8 Torx key for secure, repeatable fastening. Can this tool be used on CNC milling machines and manual machines? Yes — the indexable-insert body is suitable for standard CNC toolholders and for manual setups that accept a 32 mm shank, providing flexible application across the shop floor. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter for LNMT 0804 Indexable Inserts, 3 Flutes, 40mm Cutting Length - Teknik Makina
Take advantage of a rigid 20 mm shank and compatibility with LNMT 0804 indexable inserts to improve cycle stability and reduce setup time. The tool combines a compact overall length with three balanced cutting edges for smooth metal removal; order directly via Metav Werkzeuge or contact their consultants for application advice. Insert Milling Cutter S302TM — Indexable insert shank cutter with 20 mm shank (Teknik Makina) The Insert Milling Cutter S302TM is a shank-mounted milling tool designed for industrial machining with LNMT 0804 indexable inserts, offering reliable stability for medium-duty milling operations 20 mm shank for rigid machine spindles Compatible with LNMT 0804 indexable inserts Three cutting edges for balanced cutting Torx M2.5×7 fastening, T8 key included Increase throughput with balanced indexable cutting Equipped with three cutting edges, this shank-mounted cutter provides a steady metal removal rate and reduced vibration compared with asymmetrical geometries. The balanced cutter geometry and 20 mm shank improve run-out behaviour, which directly benefits surface finish and tool life in serial production. For operations where consistent cycle times matter, the combination of a compact overall length and a robust shank reduces the need for repeated fixture adjustments and supports more predictable machining results. Fast insert changes and predictable set-up Designed for use with LNMT 0804 indexable inserts, the tool enables quick turnover between cutting edges: indexable inserts are replaceable carbide plates that can be rotated or exchanged without regrinding the entire tool. The insert is secured by a Torx M2.5×7 screw, tightened with a T8 key, ensuring straightforward maintenance and low downtime. With a 40 mm cutting length, the holder offers a clear cutting window for many face and shoulder milling tasks, making insert replacement and controlled regrinding intervals both simple and economical. Practical compatibility and workshop benefits The insert holder is specified for compatibility with ISCAR plates and is suitable for a range of common ferrous machining tasks where indexable solutions are preferred. The tool’s moderate overall length of 150 mm and its mass contribute to a stable cutting platform without excessive overhang. This makes the tool suitable for both compact machining centres and heavier milling machines where stability and predictable tool behaviour are required. The construction supports reliable clamp-up and repeatable positioning, reducing setup time across batch changes. Contact Metav Werkzeuge for an application review or to arrange supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: S302TM Manufacturer: Teknik Makina SKU: S302TM Compatible inserts: LNMT 0804 Compatible insert manufacturer: ISCAR Data Shank diameter: 20 mm Cutting length: 40 mm Overall length: 150 mm Weight: 0.391 kg Diameter: 20 mm Number of cutting edges: 3 Special features Torx screw: M2.5x7 Torx key size: T8 Shank-mounted insert holder Indexable insert system for quick replacement FAQ Is this tool compatible with ISCAR inserts? The insert milling cutter S302TM is specified for LNMT 0804 inserts and is compatible with ISCAR indexable insert types designed to the same geometry. How is the insert secured and replaced? Replacement is performed using the Torx M2.5×7 screw; a T8 key is provided for secure fastening, allowing quick and repeatable insert changes on the S302TM holder. What machine spindles are suitable for this cutter? Machines with a tool holder or collet capable of accepting a 20 mm shank will suit this insert holder; the shank diameter helps ensure rigid clamping and improved run-out performance. Which applications benefit most from this tool? The holder is intended for medium-duty milling tasks where quick insert changes and consistent cycle times are priorities, such as face milling, shoulder milling and general finishing with indexable inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter for LOGU 0303 Indexable Inserts, 3 Cutting Edges, 20mm Shank Diameter - Teknik Makina
Take advantage of a stable 20 mm shank, precise indexing for LOGU 0303 inserts and a 150 mm overall length to keep tool changes short and production steady — order the cutter directly via Metav Werkzeuge or consult the technical advisors for integration support. S678TM shank milling cutter — 20 mm shank, for LOGU 0303 indexable inserts (Teknik Makina) The S678TM is a robust insert milling cutter body designed for modular milling operations with LOGU 0303 indexable inserts, offering secure clamping and straightforward maintenance in industrial machining environments. 20 mm shank diameter for stable clamping Compatible with LOGU 0303 indexable inserts Three cutting edges for balanced material removal M3x6 Torx screw included (T8 key required) Stable clamping and consistent cutting performance Engineered for repeatable accuracy, the cutter body features a 20 mm shank that ensures secure clamping in standard tool holders, reducing runout and vibration during machining. The three cutting edges provide a balanced cutting action that helps maintain surface quality and tool stability across the cutting pass. By using an insert system rather than brazed cutters, the design simplifies maintenance: worn edges are replaced quickly, limiting machine downtime and keeping productivity high. The solid mounting interface supports reliable repeatability for batch production tasks. Modular insert system that reduces operating costs The modular design accepts LOGU 0303 indexable inserts and is compatible with Kyocera tooling options, enabling flexible selection of grades and geometries to suit different workpieces. Using indexable inserts lowers ongoing tooling costs because only the insert is replaced when worn, not the entire cutter body. The retention uses an M3x6 Torx screw, with a T8 key required for secure fastening, enabling fast and straightforward insert changes at the machine. This approach supports efficient shift handovers and simplifies inventory management in the tool crib. Workshop-ready dimensions and integration benefits With a 150 mm overall length and a nominal 20 mm diameter, the cutter body integrates into common machining setups without bespoke adaptors. The compact profile helps preserve accessibility in tight fixtures while delivering a standard interface for spindle adapters and holders. The construction suits repetitive milling operations where predictable tool geometry and short changeover times are valued. For procurement and workshop planners, the combination of standardised interfaces and compatibility with widely available LOGU 0303 inserts makes this cutter body a practical choice for mixed production environments. For reliable, modular milling choose the Teknik Makina S678TM — contact Metav Werkzeuge in Emmerich for tailored application advice and order coordination at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S678TM Manufacturer: Teknik Makina Product: Shank milling cutter For inserts: LOGU 0303 indexable inserts Compatible insert maker: Kyocera Core data Shank diameter: 20 mm Diameter: 20 mm Overall length: 150 mm Cutting edges: 3 Torx screw: M3x6 Special features Torx key required: T8 eClass: 21180806 ETIM: EC011860 FAQ Which indexable inserts fit this cutter body? The cutter body accepts LOGU 0303 indexable inserts; compatibility with Kyocera grades is specified for flexible grade selection. What is the shank diameter and why does it matter? The 20 mm shank ensures stable clamping in standard holders, reducing runout and improving surface finish with the S678TM cutter body. How are the inserts secured? Inserts are fixed with an M3x6 Torx screw; a T8 key is used for tightening and replacement. Is this cutter suitable for serial production? Yes — the modular insert system and balanced three-edge geometry support repeatable results and short tool-change times for series work. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter for LOGU 0303 Indexable Inserts, 3 Flutes, 150mm Overall Length - Teknik Makina
Combine robust geometry with secure clamping for consistent machining results: the tool combines a Ø21 mm cutting diameter, a 20 mm shank and three cutting edges to deliver stable material removal and straightforward insert replacement. Order the tool directly via Metav Werkzeuge or consult the Metav advisors for application guidance and fast supply. Schaftfräser S679TM — Shank milling cutter, Ø21 mm, 3 flutes (Teknik Makina) The Schaftfräser S679TM is a shank milling cutter designed to accept LOGU 0303 indexable inserts and suited to repetitive milling tasks where secure insert clamping and consistent cutting geometry are required Ø 21 mm cutting diameter 20 mm shank for secure clamping 3 cutting edges for stable removal Compatible with Kyocera LOGU 0303 inserts Delivering consistent cutting performance for production runs The solid tool body and optimised flute geometry ensure repeatable results in cyclic milling operations. With a Ø21 mm diameter and a 20 mm shank, the cutter reduces runout and enhances toolholder engagement, which improves dimensional stability on serial work. The 3 flutes provide a balance between chip evacuation and cutting engagement, enabling steady feed rates while maintaining surface quality. This combination supports efficient machining cycles and predictable tool life, making the cutter suitable for organised shop-floor production. Fast insert changes and secure clamping to minimise downtime Designed for indexable inserts, this cutter uses a standard Torx fastening system that keeps service times short. The use of an M3x6 Torx screw and the corresponding T8 key allows quick and repeatable insert clamping, reducing non-productive time during re‑gripping or insert replacement. Compatibility with Kyocera LOGU 0303 inserts means access to readily available cutting grades and geometries; the result is lower inventory complexity and faster restoration of cutting performance after a tool change. Clear mechanical fixation ensures consistent seat contact and predictable cutting behaviour. Integrating the cutter into workshop workflows with reliable supply As a purpose-built shank milling tool from Teknik Makina, the design focuses on straightforward integration with common toolholders and indexable insert systems. The measured dimensions — Ø21 mm cutting diameter, 20 mm shank and 150 mm overall length — make it a pragmatic choice for operations where tool stability and repeatability matter. Where longer runs and tight scheduling are part of the workflow, the tool’s compatibility with widely used insert systems and standard fastening reduces logistical friction and supports efficient stocking strategies at the workbench. For precise, reliable milling with Teknik Makina quality, contact Metav Werkzeuge in Emmerich for tailored advice and assured supply: info@metav-werkzeuge.com; +49 2822 7131930 Technical Data Article number: S679TM Name: Schaftfräser Description: for LOGU 0303 Indexable Inserts Manufacturer: Teknik Makina Data Cutting diameter: 21 mm Shank diameter: 20 mm Overall length: 150 mm Cutting edges: 3 Special features Compatible inserts: LOGU 0303 (Kyocera) Fastening screw: M3x6 Torx Torx key: T8 Application: milling with indexable inserts FAQ Which inserts fit this milling cutter? The cutter accepts LOGU 0303 indexable inserts; compatibility with Kyocera LOGU 0303 inserts is specified for straightforward replacement and access to common grades. What are the key dimensions of the tool? The milling cutter has a 21 mm cutting diameter, a 20 mm shank diameter and a 150 mm overall length, providing stable clamping and suitable reach for many shop applications. How are the inserts secured in the cutter? Inserts are retained with an M3x6 Torx screw; a T8 Torx key is required for secure and repeatable clamping of the indexable inserts. Is this cutter suitable for quick tool changes in production? Yes, the combination of standard Torx fixation and LOGU 0303 insert compatibility is intended to minimise downtime and support efficient insert replacement in serial production. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Shank Cutter For RDMT 1003 Indexable Inserts, 3 Flutes, 45mm Cutting Length - Teknik Makina
Take advantage of a robust, production-ready milling solution: a solid 32 mm shank provides stability, the tool accepts RDMT 1003 indexable inserts for economical cutting, and the three cutting edges deliver consistent material removal. Order the shaft cutter directly via Metav Werkzeuge or consult our specialists for application support. R204TM shaft cutter for RDMT 1003 indexable inserts — 32 mm shank, 3 cutting edges (Teknik Makina) The R204TM shaft cutter for RDMT 1003 indexable inserts is a purpose-built milling tool engineered for stable, repeatable performance in industrial machining environments. 32 mm shank diameter for stable toolholding Three cutting edges for smooth chip control 45 mm cutting length improves reach and versatility Compatible with RDMT 1003 indexable inserts Stability that reduces vibration and improves finish A generous 32 mm shank and compact mass provide a stable connection to the spindle, which reduces vibration and supports consistent surface quality in serial production. This structural stability translates into fewer rejected parts and lower rework time, enhancing overall process reliability. The design supports high clamping rigidity so that accuracy is preserved during heavier cuts, contributing to measurable productivity gains and predictable cycle times. Productivity through indexable inserts and optimised cutting geometry Accepting RDMT 1003 indexable inserts allows fast insert changes and cost-efficient use of cutting material. With 3 cutting edges, the tool balances chip load evenly across each rotation, improving chip evacuation and allowing sustained cutting performance. The indexable system reduces downtime for tool maintenance and spreads tooling cost across multiple edges, making the cutter a pragmatic choice for medium- to high-volume milling tasks where repeatability and quick serviceability matter. Practical service features for fast changeover Service and changeover are simplified with clear fastenings: a M3.5 locking screw and a Torx screw M3.5x8.5 secure the insert reliably, while the supplied Torx key T15 ensures correct tightening without specialised tooling. The accessible screw arrangement and standardised fastening sizes shorten maintenance intervals and reduce the risk of incorrect assembly. These features help maintain consistent cutting conditions and lower the probability of tool-related stoppages on the shopfloor. Suitable form factor for diverse machining setups With a 45 mm cutting length and 150 mm overall length, the tool offers a blend of reach and rigidity suitable for a wide range of milling operations where RDMT 1003 inserts are used. The moderate mass of 0.898 kg is compatible with many toolholders without imposing excessive centrifugal forces at typical spindle speeds. The configuration supports adaptable setups on milling heads and machining centres, making the cutter appropriate for series production and flexible workshop applications. Consult Metav Werkzeuge for technical advice and to arrange supply of the Teknik Cutting Tools R204TM shaft cutter with 32 mm shank for reliable production results Technical data Article number: R204TM Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Cutting length: 45 mm Overall length: 150 mm Number of cutting edges: 3 Weight: 0.898 kg Special features Compatible with RDMT 1003 indexable inserts Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 FAQ Which inserts fit this cutter? The cutter is designed for RDMT 1003 indexable inserts; use inserts compliant with that designation for correct seating and cutting performance. Is the shank suitable for heavy-duty milling? The 32 mm shank offers high rigidity for stable milling; however, final suitability depends on the machine spindle and cutting parameters selected for each job. What fasteners are used to secure the inserts? The tool uses a M3.5 locking screw and a M3.5x8.5 Torx screw; a T15 Torx key is specified for assembly and torque control. Can the cutter be used on standard toolholders? The cutter’s shank diameter and form factor make it compatible with commonly used toolholders that accept a 32 mm shank, subject to correct clamping practice. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Shank Cutter For VCGT 1604 Indexable Inserts, 2 Flutes, 25mm Shank Diameter - Teknik Makina
Take advantage of a compact, insert-based milling solution that combines stable clamping with swift insert changes; the 25 mm shank and 50 mm cutting length ensure reliable medium-depth passes while compatibility with VCGT 1604 inserts simplifies tool management — order via Metav Werkzeuge or consult our specialists for application-specific advice. Insert milling cutter S710TM – for VCGT 1604 indexable inserts (Teknik Makina) The Insert milling cutter S710TM is a shank-mounted milling tool designed for precision steel machining with VCGT 1604 indexable inserts, offering a balanced combination of rigidity and serviceability for production and job-shop environments. 25 mm shank for stable clamping Compatible with VCGT 1604 indexable inserts 50 mm cutting length for medium-deep passes Secured with M4x10 Torx screw (T15) Consistent cutting performance for efficient production The S710TM delivers predictable metal removal by combining a 25 mm shank with a compact geometry that reduces chatter and improves surface quality. Using VCGT 1604 indexable inserts allows maintenance of a consistent cutting edge geometry across multiple operations, which reduces setup time and increases uptime. With 2 cutting edges the tool balances material removal rate and tool life, making it suitable for standard to demanding milling cycles where repeatability matters. Secure clamping and fast insert changes for less downtime A robust fastening system using an M4x10 screw and Torx T15 key ensures the insert is clamped precisely and can be changed quickly during shift work. This secure connection lowers the risk of insert movement under load and supports higher feed rates within the cutter’s operating envelope. The clear mechanical interface simplifies replacement routines and helps maintain process stability across batch runs. Engineered for reliable steel machining and longevity Designed with practical workshop needs in mind, the cutter is optimised for steel machining, delivering stable cuts and predictable wear behaviour. The 50 mm cutting length gives sufficient reach for common slotting and peripheral passes without compromising rigidity, while the shank configuration keeps the tool runout low. The result is fewer scrapped parts and more consistent component tolerances in daily production. Easy integration into existing tooling systems With compatibility for standard VCGT 1604 inserts and a conventional shank diameter, the tool integrates smoothly into established toolholders and machine setups. The overall compact design and a weight of 0.518 kg make handling and storage straightforward, while the standardised insert format reduces the variety of spare parts required. This facilitates leaner inventory management and helps maintain continuous supply to the workbench. Contact Metav Werkzeuge in Emmerich for personalised application advice and dependable supply of the Teknik Makina S710TM insert milling cutter, including technical data and order assistance Technical data Article number: S710TM Manufacturer: Teknik Makina Key measurements Shank diameter: 25 mm Cutting length: 50 mm Overall length: 150 mm Diameter: 25 mm Number of cutting edges: 2 Weight: 0.518 kg Features & compatibility For VCGT 1604 indexable inserts Fastening screw M4x10 Torx key size T15 Shank-mounted insert cutter Suitable for steel machining FAQ Which inserts fit this cutter? The S710TM is designed for VCGT 1604 indexable inserts; this format provides a wide choice of grades for different steels and cutting conditions. What is the shank diameter and why does it matter? The shank diameter is 25 mm, which provides stable clamping and low runout when used with appropriate collets or holders, improving machining accuracy. How long is the cutting length and what does that enable? The tool offers a 50 mm cutting length, suitable for medium-depth passes and common milling tasks without excessive overhang. Which screw and key are required for insert changes? Insert retention uses an M4x10 screw and a Torx T15 key for secure and repeatable clamping. Is this cutter suitable for high-speed milling? The S710TM is optimised for stable steel machining and repeatable performance; cutting speed suitability depends on insert grade and machine capability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
High-performance shank cutters and ball nose cutters for efficient milling
Insert shank cutters and ball nose cutters combine flexibility and productivity for a wide range of milling tasks. The category covers steel-bodied shank cutters fitted with indexable inserts for economical roughing, face milling, cornering and slotting, as well as ball nose cutters for contouring and 3D finishing.
How these tools work and where they belong
Shank cutters with indexable inserts use a carrier body made from hardened steel; the cutting edges are provided by removable inserts rather than a solid tool blank. Where tools do not have internal coolant, process heat and chips are managed via external coolant nozzles or compressed air, which is sufficient for open, surface-level and easily accessible milling on standard materials. Shank cutters with internal coolant feature fine internal channels that deliver coolant or blasting air directly to each cutting edge under pressure. This targeted supply is essential for deep pockets, cavities, full slotting and machining of heat-resistant or difficult-to-machine materials, because it prevents chip re-cutting, protects cutting edges from thermal overload and enables higher feed rates and improved surface quality.
Cut cycle times and reduce tooling costs
- Replaceable indexable inserts reduce consumable costs and shorten tool change time.
- Targeted internal coolant improves chip evacuation and extends insert life.
- Robust steel carrier bodies enable heavy-duty roughing without frequent tool replacement.
- Suitable for roughing, planing, corner milling and slot milling as well as precision 3D profiling with ball nose cutters.
A practical choice for purchasing and stocking tools
Metav brings a pragmatic purchasing advantage: a broad range of milling solutions is available from a single European quality hub. Metav’s focus on democratising precision means workshops benefit from a wide assortment, consistent quality control from Emmerich and steady supply — supported by decades of expertise and over 48,000 satisfied customers. Choose Metav for a centralised sourcing strategy that reduces supplier complexity while keeping access to both insert milling cutters (also referred to as insert milling cutters or indexable end mills) and ball nose cutters (also known as ball nose end mills or radius cutters) straightforward.
Quick summary
Insert shank cutters and ball nose cutters deliver flexible, cost-effective milling: replaceable inserts lower running costs, and internal coolant options enable higher performance and longer tool life where chip control is critical.
FAQ
When should I choose a shank cutter with indexable inserts rather than a solid carbide end mill?
Choose shank cutters with indexable inserts for economical roughing and high-stock-removal tasks where replacing inserts is preferable to replacing an entire tool; they are especially effective for face milling, cornering and slotting operations.
Does internal coolant make a measurable difference for ball nose cutters?
Yes. Internal coolant directed to each cutting edge reduces chip re-cutting and thermal stress, which improves surface finish and increases insert life when machining deep pockets, cavities or heat-resistant materials.
Can shank cutters without internal coolant be used for general workshop milling?
Absolutely. Tools without internal coolant rely on external coolant nozzles or compressed air and are well suited to open, superficial and easily accessible milling on standard materials.
What milling operations are shank cutters for indexable inserts typically used for?
Shank cutters with indexable inserts excel at economical roughing, planfräsen (face milling), corner milling and slot milling; ball nose cutters are the preferred choice for 3D profiling and finishing operations.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com