Reliable drilling performance with Standard Line twist drill
Standard Line twist drill and standard drills deliver consistent, precision holemaking for daily industrial and workshop use, combining durable high-speed steel construction with precision-ground flutes to ensure excellent runout and chip evacuation. Designed for machining unalloyed and low-alloy steel, cast iron, sintered metal, plastics and non-ferrous metals, these drills provide a balanced mix of wear resistance and hole quality for routine production and maintenance tasks. Ideal for workshops, maintenance departments and assembly plants, the system offers a dependable, cost-effective solution between entry-level and heavy-duty ranges, featuring an optimised 118° point for good penetration and centring. Key advantages include precision-ground construction, excellent chip evacuation and consistent hole quality.
7.7mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
MetavCUT Twist Drill – Type N short, 7.7 mm, HSS‑E, 135°, 5% cobalt‑alloyed, fully ground, DIN 338 The Twist Drill from MetavCUT is a short Type N drill designed for precision metalworking and optimized for drilling machines and hand drills. Short design for increased stability and precision 7.7 mm Diameter for accurate through‑holes 135° Point angle for hard materials like stainless steel Fully ground shank for high runout accuracy HSS‑E with 5% cobalt for enhanced wear resistance Precision and stability for demanding metalwork The short Twist Drill construction reduces the protruding length from the chuck, resulting in markedly improved Stability and less tendency to bend under load. This makes the tool particularly suitable for precise operations and for drilling in hard Metals where deflection would compromise hole quality. With a 135° Point Angle, the cutting action engages smoothly on tough surfaces, shortening dwell on entry and improving centring on stainless steel and alloyed steels. Material composition and durability benefits Manufactured from HSS‑E with 5% cobalt alloying, this short Type N drill offers improved Heat Resistance and edge life compared with standard HSS. The cobalt content supports higher cutting temperatures and helps maintain sharpness when machining alloyed or high‑strength Steels. The fully ground flute geometry provides very sharp cutting edges and high roundness, which delivers clean holes and consistent tool life under appropriate coolant and machine conditions. Designed for efficient workshop use By combining a short overall length with a roll‑free, fully ground shaft and compliance with DIN 338, the drill delivers reproducible hole quality on stationary and portable machines alike. The reduced overhang lowers vibration, enabling higher feed rates and improved surface finish for through‑holes. For routine metal drilling tasks the short HSS‑E Twist Drill allows operators to maintain productivity without sacrificing precision. Recommended applications and user guidance This Twist Drill is optimised for drilling in Alloyed and Unalloyed Steel, Cast Iron, Non‑Ferrous Metals and Plastics when high precision is required. For best results, use appropriate cutting fluid and secure workholding; short drills perform best in guided or rigid setups. If drilling in softer woods, be aware that metal drills can work but may show inferior guidance and finish compared with purpose wood drills. For holes up to moderate depths, the short geometry reduces breakage risk in small diameters and improves repeatability. Strong recommendation from MetavCUT: Choose this short HSS‑E Type N Twist Drill for stable, high‑precision metal drilling — for technical advice or application support contact METAV Werkzeuge: info@metav-werkzeuge.com, Tel +49 2822 7131930, WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Marke: MetavCUT SKU: 47077-FDA Diameter: 7.7 mm Point Angle: 135° Type: Type N Execution: short Colour: 5% cobalt‑alloyed Material: HSS‑E Standard: DIN 338 Shank Finish: fully ground Overall Length: 117 mm Spiral Length: 75 mm For Drilling Machine: Drilling Machine / Hand Drill applications Application: Drills for metal Model Series: Standard Line Designation (EN): Twist Drill Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N primarily used for? The MetavCUT Twist Drill Type N is primarily used for machining high‑strength and alloyed Metals; it excels in through‑holes for metalworking thanks to its short design and HSS‑E composition, which combined allow reliable drilling in demanding materials. Can the MetavCUT Twist Drill be used for wood? The MetavCUT Twist Drill (Type N) can be used in Wood, but as a Metal drill it offers less guidance and a rougher finish than a dedicated Wood drill; it is easier to re‑sharpen and shows less self‑pulling action compared with specialised wood bits. For what is a Twist Drill used? A Twist Drill is mainly applied to the machining of high‑strength workpieces and larger drill diameters; its shape allows straightforward re‑grinding and it withstands greater loads, making it suitable for drilling Metal and other tough materials. Which three drill types exist? The main drill categories are Metal drill, Wood drill and Stone/Concrete drill, and the MetavCUT Twist Drill belongs to the Metal drill group designed for steels and non‑ferrous Metals. Why are Twist Drills pointed? The point profile reduces the secondary cutting edge at the tip, lowering friction and thus decreasing required feed forces; this sharpening also improves centring accuracy when the MetavCUT Twist Drill is used in the workpiece. For which drilling depths is the Twist Drill most used? A solid bore is typically executed with a Twist Drill; for diameters up to about 20 mm and depths up to 100 mm, the Twist Drill is the most commonly used tool thanks to its versatile geometry and reliability. What is better, HSS or HSSE? The general assumption that HSSE steels are always superior to HSS is not correct; when deciding for the MetavCUT Twist Drill in HSS‑E, assess whether the working conditions justify the higher cost of HSSE, as performance gains depend on the specific application and material.
7.7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short Twist Drill Ø 7.7 mm, 135° Tip, Type N, Bright finished, Short, HSS‑G, DIN 338 The Twist Drill is a short Type N metalworking drill designed for precision drilling in hard materials and suited for use with a Drilling Machine. Short design for increased stiffness Ground HSS for faster, precise drilling 135° tip angle for reduced walking in hard materials Fully ground shank for high runout accuracy Conforms to DIN 338 for consistent quality Greater Precision through a Short, Stable Design A shorter geometry reduces the exposed length and therefore the tendency to bend, delivering noticeably better stability during machining. The short configuration of this twist drill makes it especially effective for precise work in metal, where less vibration and improved concentricity yield cleaner holes. Users benefit from improved control when working on tight setups or thin workpieces, since the reduced cantilever minimizes deflection and tool chatter. Faster Cutting with Ground HSS for Hard Materials The HSS‑G ground geometry enables higher cutting performance: up to 40% faster penetration and lower required feed force compared with conventional HSS designs, according to manufacturer data. This feature is particularly advantageous when drilling alloyed and unalloyed steel, cast iron, sintered materials and hard plastics. The ground flute geometry also produces sharper cutting edges and consistent chip evacuation, which supports longer tool life under appropriate cooling. Optimised Tip Geometry for Accurate Starts A 135° tip angle is recommended for harder workpiece materials because it shortens the initial cutting time and reduces the risk of punch‑through and tip wandering. The Type N normal spiral is a classic metal drill geometry, providing reliable centring and consistent chip removal for a wide range of metallic applications. For users unfamiliar with tip angles: a larger angle means a flatter point that spreads cutting action over a wider area, which reduces pressure per unit area at the entry. Compatibility, Standards and Practical Use Manufactured to DIN 338, this short twist drill matches established dimensions and tolerances for short cylindrical shank drills, easing integration into workshop inventories. The fully ground shank improves run‑out accuracy in chucks and sleeves, which is critical for high‑precision drilling operations. Although mainly intended for stationary or hand Drilling Machines, the design supports use in many standard metalworking environments when appropriate clamping and cooling are applied. Who Benefits and How to Apply It Professional machinists and skilled hobbyists who need accurate holes in hard or alloyed metals will appreciate the combination of stiffness and sharp cutting geometry. When drilling, ensure adequate coolant or lubrication for tough materials and moderate spindle speeds to keep temperatures down; reducing thermal load preserves edge life on the HSS‑G material. For tasks that require extreme impact or interrupted cuts, consider machine setup and feed rates to avoid brittle fracture of the ground tool. We recommend the MetavCUT Twist Drill for precision metalworking applications — for personalised technical advice or to confirm suitability for your task contact METAV Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45077-FDA Diameter: 7.7 mm Spiral Length: 75 mm Total Length: 117 mm Tip Angle: 135° Type: Type N Execution: Short Shaft Finish: Fully ground Colour: Bright finished Material: HSS‑G Norm: DIN 338 Application: Drills for metal For Drilling Machine: Drilling Machine Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for machining high‑strength materials and larger drill diameters; its short execution and ground geometry make it suitable for precise metalworking tasks where stability and accurate holes are required. The shape allows easier resharpening and reliable performance under appropriate cooling. Which three drill types exist? Generally, drills are grouped as metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metals rather than masonry or softwood applications. Can the Twist Drill be used in wood? The MetavCUT Twist Drill can be used in wood, but as a metal drill it offers less guidance and a rougher finish compared with dedicated wood drills; it is easier to resharpen and exhibits lower self‑feeding, so results may be acceptable for rougher wood work but not for fine woodworking finishes.
7.8mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N, 7.8 mm, 118°, HSS, short, black, DIN 338 (MetavCUT) The Twist Drill from MetavCUT is a short Type N drill designed for precision metalworking in drilling machines and hand drills, offering a 7.8 mm diameter and a 118° point angle for reliable centring and stable performance. Short HSS design for improved stability Precise 7.8 mm diameter for accurate holes 118° point angle for better centring on workpieces Conforms to DIN 338 for short twist drills Suitable for drilling machines and hand drills Robust HSS construction for durable metalworking Built from HSS (High Speed Steel), this short Twist Drill combines toughness and elasticity for demanding metal applications. The roll-formed HSS manufacturing process reduces the risk of breakage when drilling smaller diameters and provides consistent performance in alloyed and unalloyed steel, cast iron, non-ferrous metals and many plastics. The compact geometry increases rigidity, which means fewer vibrations and cleaner hole quality when used in appropriate machines. Short length and Type N spiral for precision and stability A shorter overall length reduces overhang and thus the tendency to bend, delivering higher accuracy during machining. The short execution specified by DIN 338 makes the tool particularly suitable where stability and concentricity matter. The Type N normal spiral flute is optimised for metalwork, guiding chips away reliably while maintaining cutting edge life, and the 118° point angle supports easier centring on curved or less-than-flat surfaces. Practical guidance on application and material compatibility When the task involves drilling into steel, cast components or non-ferrous metals, the MetavCUT short Twist Drill is a practical choice thanks to its HSS composition and classical flute geometry. For softer materials a different point angle may be preferable, but for standard metalwork this configuration balances penetration and edge robustness. Regular checking of feed and speed settings in the drilling machine helps to maximise tool life and hole finish. Who benefits and how to get optimal results Workshop professionals and maintenance technicians who require repeatable, precise holes in metal benefit most from this short HSS Type N design. For best results, use appropriate cutting fluid when machining steels, ensure the drill chuck is concentric and avoid excessive feed that could overload the small-diameter flute. Proper resharpening of the 118° tip restores centring performance and lowers the required feed forces. MetavCUT recommends the short HSS Type N Twist Drill for reliable, high‑precision metal drilling; for technical advice, suitability checks or further specifications contact METAV Werkzeuge — 📧 info@metav-werkzeuge.com — ☎️ +49 2822 7131930 — ✔️ WhatsApp +49 170 2837271 Technical specifications Designation: Twist Drill Brand: MetavCUT SKU: 40078-FDA Type: Type N Diameter: 7.8 mm Point angle: 118° Material: HSS (High Speed Steel) Spiral length: 75 mm Overall length: 117 mm Execution: short Colour: black Application: Drills for metal Standard: DIN 338 For drilling machine: Drilling machine Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for and where does the MetavCUT Type N excel? The MetavCUT Twist Drill Type N is mainly applied to machining high-strength materials and larger bore diameters in metalworking; its short HSS design offers stability and easier handling under demanding loads, providing longevity and reliable performance for workshop and production use. Which three drill types exist and how does this product fit in? The three common drill categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking tasks with a Type N spiral and HSS material. Why are Twist Drills pointed and what is the benefit of the 118° tip on the MetavCUT drill? The point reduces the cross-edge at the tip of a Twist Drill; by pointing the tip the friction is significantly lowered, requiring less feed force and improving centring in the workpiece. The 118° geometry on the MetavCUT item balances penetration and centring for many common metals. Can a metal Twist Drill be used to bore wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but guidance and surface finish are inferior compared with dedicated wood drills. Metal drills are easier to resharpen and have lower self-feeding tendencies, yet they provide less precise tracking in soft timber. For which drilling depths and diameters is the Twist Drill most commonly used? A solid bore is typically made with a Twist Drill. For diameter ranges up to 20 mm and drilling depths up to 100 mm the Twist Drill is the most frequently used tool, making the MetavCUT short HSS drill suitable for many standard metalworking operations. Is HSS or HSSE better for metal drilling? The general belief that HSSE steels are always superior to HSS is not universally correct. Selection should consider actual working conditions and whether the higher acquisition cost of HSSE is justified; MetavCUT provides advice to choose the most appropriate grade for the intended application.
7.8mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill — MetavCUT Type N short HSS‑E, 7.8 mm, 135°, 5% cobalt‑alloyed, fully ground shank, DIN 338 The Twist Drill Type N short is a precision metalworking drill for drilling machines, designed for stable, accurate holes in hard and alloyed steels. Short design for higher stability and reduced deflection 135° point angle for hardened and stainless steels 5% cobalt‑alloyed HSS‑E for improved wear resistance Fully ground shank for high concentricity and precise running Conforms to DIN 338 for short cylindrical‑shank twist drills Durable HSS‑E construction for demanding metalwork Built from HSS‑E with 5% cobalt, this short twist drill offers increased Heat Resistance and superior wear behaviour when cutting alloyed and unalloyed steels. The cobalt‑enrichment improves toughness at elevated cutting temperatures, so the tool maintains its cutting geometry longer during repetitive metal drilling. This results in fewer tool changes and greater process reliability without sacrificing hole quality. Stable short length for precision drilling A reduced overall length and a shorter Spiral Length give the drill a stiffer setup and less tendency to bend under load. That improved rigidity makes the short Twist Drill especially suitable for precision work and for drilling into hard materials where accuracy is essential. For shop applications on drilling machines or hand drilling machines, the compact geometry contributes directly to cleaner holes and better positional accuracy. Geometry optimised for hard materials The 135° point angle reduces walking on the surface and shortens the plunge time when starting holes in tougher materials such as stainless steel. Combined with the Type N normal spiral geometry, this results in reliable chip evacuation and consistent cutting action when working with metal. For users less familiar with drill geometry: a larger point angle leads to a flatter tip that resists wear and improves centering on hard surfaces. Precision shank and production standard The fully ground cylindrical shank (HSS‑G style) ensures excellent concentricity in chucks and collets, reducing runout and vibration. Manufactured to DIN 338, this short twist drill follows industry standards for dimensions and tolerances, making it easy to integrate into existing tooling setups. The careful grinding process yields sharp cutting edges and a clean drill profile, which is beneficial for fine metalworking and repeatable results. Practical guidance for use and care When using this short Twist Drill in metal, apply adequate cutting fluid and moderate feed to exploit the HSS‑E properties and avoid overheating. Short drills tolerate higher feeds thanks to their stiffness, but cooling remains crucial to extend life. For repairs or modifications, remember that fully ground drills can be re‑sharpened to restore cutting edges, though sharpening requires suitable tooling and skill to preserve geometry. Choose MetavCUT’s short Twist Drill for reliable, precision metal drilling — for personalised technical advice and application support contact METAV Werkzeuge: eMail info@metav-werkzeuge.com, Phone +49 2822 7131930, WhatsApp +49 170 2837271 Technical information Designation: Twist Drill Brand: MetavCUT SKU: 47078-FDA Type: Type N Diameter: 7.8 mm Spiral Length: 75 mm Overall Length: 117 mm Point Angle: 135° Execution: short Material: HSS‑E Coating / Alloy: 5% cobalt‑alloyed Shank Execution: fully ground Suitable for: drilling machine (hand drilling machine compatible) Model Series: Standard Line Norm: DIN 338 Applications: drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ For what is the Twist Drill used? The MetavCUT Twist Drill is primarily used for machining high‑strength materials and larger drill diameters in metalworking; its short design and grindable form make it suitable for applications that demand precision and resistance to high loads. Which 3 drill types exist? In general drilling practice the main types are metal drills, wood drills and stone/concrete drills; the MetavCUT Twist Drill belongs to the metal drill category and is optimised for steel and similar materials.
7.8mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Kompakte Konstruktion und geschliffene HSS-Geometrie sorgen für schnelle, präzise Bohrungen in Stahl bei reduziertem Anpressdruck. Nutzen Sie die Kombination aus hoher Stabilität durch kurze Ausführung und dem 135° Spitzenwinkel für härtere Werkstoffe. Bestellen Sie den Bohrer direkt bei Metav oder fragen Sie unsere Beratung an. Spiralbohrer | kurzer HSS‑G Bohrer von MetavCUT Standard Line Der Spiralbohrer kurz eignet sich für präzise Metallbearbeitung an Handbohrmaschine und stationären Maschinen und vereint Stabilität mit schnellem Vorschub HSS-G, geschliffen für hohe Präzision 135° Spitzenwinkel für härtere Werkstoffe Kurze Ausführung für erhöhte Stabilität Zylinderschaft: ideal für Handbohrmaschine Spirallänge 75 mm für verlässliche Spanabfuhr Hohe Schnittleistung dank geschliffener HSS-Geometrie Das Material HSS-G steht für Schnellarbeitsstahl mit geschliffener Spannutengeometrie, was scharfe Schneiden und hohe Rundlaufgenauigkeit ermöglicht. Durch die geschliffene Ausführung reduziert sich der Anpressdruck spürbar, wodurch das Bohren bis zu 40 % schneller erfolgen kann und gleichzeitig etwa 50 % weniger Anpresskraft erforderlich ist. Dieser Vorteil führt zu geringerer Bedienermüdung und konstanter Bohrungsqualität. Zuverlässigkeit bei härteren Werkstoffen durch 135° Spitzenwinkel Für legierte und unlegierte Stähle ist der 135° Spitzenwinkel ideal, weil er die Anbohrphase verkürzt und das Wanderverhalten verringert. Für Anwendungen in Edelstahl, Gussstahl oder Temperguss empfiehlt sich dieser Winkel, kombiniert mit Kühlschmierstoff und moderater Schnittgeschwindigkeit. Der Bohrer eignet sich damit besonders für Werkstatt‑ und Montageeinsätze, bei denen zügiges und sauberes Arbeiten zählen. Kurze Ausführung für maximale Stabilität und Präzision Die kurze Bauform mit einer Gesamtlänge von 117 mm und einer Spirallänge von 75 mm reduziert die Auskragung aus dem Bohrfutter und minimiert Verbiegevorgänge. Das Ergebnis sind präzisere Bohrbilder und bessere Rundlaufwerte, besonders wichtig bei sichtbaren oder passungsgebundenen Bohrungen. Deshalb ist diese Ausführung erste Wahl für stationäre Säulenbohrmaschinen und Handbohrmaschinen, die mit konstanter Führung arbeiten. Praxisorientierte Hinweise für effektive Anwendung Für besten Verschleißschutz und optimale Spanabfuhr wird Kühlung empfohlen, vor allem bei tiefen Bohrungen und harten Werkstoffen. Vorbohren mit einem Zentrierbohrer verbessert die Zuverlässigkeit, und kontrollierte Vorschubraten verlängern die Lebensdauer. Der Spiralbohrer kurz eignet sich für dünne bis mittlere Bleche sowie für allgemeine Stahlbearbeitung im Standard‑Bereich. Empfehlung: Die MetavCUT Lösung wählen — den kurzen HSS‑G Spiralbohrer direkt beim Metav Team anfragen per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 für technische Beratung und Lieferoptionen Produktmerkmale Artikelnummer: 45078-FDA Marke: MetavCUT Serie: Standard Line Fakten Durchmesser: 7,8 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Besonderheiten Material: HSS-G (Schnellarbeitsstahl, geschliffen) Norm: DIN 338 Typ: Typ N (Normalspirale, Metall) Ausführung: kurz Schaftausführung: geschliffen (Zylinderschaft) Farbe: blank (blankfinish) Verwendung: Bohrer für Metall Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 10 FAQ Für welche Materialien ist dieser Spiralbohrer optimal geeignet? Der MetavCUT Spiralbohrer (Standard Line) mit HSS-G und 135° Spitzenwinkel ist ausgelegt für legierte und unlegierte Stähle, Gussstahl, Gusseisen sowie Nichteisenmetalle und Hartkunststoffe; bei harten Werkstoffen empfiehlt sich Kühlung. Eignet sich der Bohrer für Handgeführte Geräte? Ja, der kurze Spiralbohrer ist wegen geringerer Auskragung stabiler und eignet sich für Handbohrmaschine; bei sensiblen Passungen ist eine Führung oder Säulenbohrmaschine empfehlenswert. Welche Norm und Fertigungsart liegen diesem Bohrer zugrunde? Der Bohrer entspricht der Norm DIN 338 und ist als geschliffener HSS‑Bohrer (HSS‑G) ausgeführt, was sehr scharfe Kanten und hohe Rundlaufgenauigkeit ermöglicht. Wie wirkt sich der 135° Spitzenwinkel in der Praxis aus? Der 135° Spitzenwinkel verkürzt die Anbohrzeit und reduziert das Wandern beim Ansetzen, besonders vorteilhaft bei Edelstahl und härteren Stählen. Welche Abmessungen haben Gesamtlänge und Spirallänge? Die Gesamtlänge beträgt 117 mm bei einer Spirallänge von 75 mm, was die Stabilität erhöht und für verlässliche Spanabfuhr sorgt.
7.8mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Der kurze HSS‑G Kurzbohrer überzeugt durch erhöhte Stabilität bei geringer Auskraglänge und verlängerte Standzeit dank TIN‑Beschichtung; die geschliffene Geometrie sorgt für präzise Bohrlöcher in Stahl und NE‑Metall. Bestellen Sie den MetavCUT Kurzbohrer unkompliziert über Metav‑Werkzeuge oder fragen Sie die Technische Beratung für Einsatzoptimierung an. Spiralbohrer HSS‑G Kurzbohrer von MetavCUT Der Spiralbohrer ist ein kurzer, geschliffener HSS‑G Metallbohrer mit TIN‑Beschichtung, konzipiert für präzise Bohrungen in Stahl und NE‑Metallen Kurz‑Ausführung für höhere Stabilität bei Bohrarbeiten TIN‑Beschichtung reduziert Reibung und Verschleiß Geschliffen für hohe Rundlaufgenauigkeit Spitzenwinkel 135° für harte Werkstoffe Zylinderschaft und Eignung für Handbohrmaschine Hohe Standzeit durch Materialwahl und Beschichtung Die Kombination aus HSS‑G‑Werkstoff und TIN‑Beschichtung bietet gezielte Vorteile beim Bohren von Metall: Die Oberfläche reduziert Reibung und Hitzeentwicklung, was die Standzeit des Werkzeugs erhöht und die Spanbildung kontrolliert. Dadurch kann die Arbeitseffizienz gesteigert werden, da Bohrzyklen seltener unterbrochen werden müssen. Die geschliffene Schneidgeometrie unterstützt saubere Bohrlöcher mit geringem Ausriss. Kurzbauweise für mehr Steifigkeit und Präzision Die kurze Ausführung reduziert die Auskraglänge und minimiert Schwingungen, was die Bohrgenauigkeit verbessert. Mit einer Spirallänge von 75 mm und einer Gesamtlänge von 117 mm bleibt die Werkzeugaufnahme stabil, insbesondere bei stationären Säulenbohrmaschinen oder gut geführten Handbohrmaschinen. Die Einhaltung der DIN 338 gewährleistet standardisierte Abmessungen und Kompatibilität mit Zylinderschaftaufnahmen. Vielseitige Einsatzgebiete in Metall und Hartkunststoff Das Werkzeug ist ausgelegt für legierten und unlegierten Stahl, Temperguss, Gusseisen, Sintereisen, NE‑Metalle wie Neusilber, Kupfer und Bronze sowie Hartkunststoff. Im Standard‑Bereich (2–13 mm) erfüllt der Bohrer typische Werkstatt‑ und Montageaufgaben zuverlässig. Bei Bedarf sorgt geeignete Kühlung für eine weitere Reduktion von Verschleiß und Thermobelastung. Praxistipps für sichere und effiziente Anwendung Für hohe Präzision empfiehlt sich bei kritischen Passungen das Anpunkten mit einem Zentrierbohrer; für allgemeine Bohrungen kann direkt gearbeitet werden. Der Spitzenwinkel von 135° erleichtert das Anbohren harter Werkstoffe und verringert das Auslaufen der Bohrspitze. Durch die geschliffene Fertigung ist auf die richtige Spannmittelgeometrie und die Vermeidung von Verkantungen zu achten, um Bruchrisiken zu minimieren. Mit dem MetavCUT HSS‑G Kurzbohrer auf Präzision setzen — für Beratung und Bestellwunsch erreichen Sie Metav per E‑Mail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Leistungsmerkmale Artikelnummer: 46078‑FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Typ: Typ N Daten Durchmesser: 7,8 mm Spirallänge: 75 mm Gesamtlänge: 117 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Material: HSS‑G (geschliffen) Farbe: TIN‑beschichtet (Titan‑Nitrid) Schaft: Zylinderschaft Schaftausführung: geschliffen Für Handbohrmaschine Norm: DIN 338 FAQ Welche Werkstoffe lassen sich mit dem MetavCUT HSS‑G Kurzbohrer bearbeiten? Der MetavCUT HSS‑G Kurzbohrer eignet sich für legierten und unlegierten Stahl, Temperguss, Gusseisen, Sintereisen, NE‑Metalle wie Kupfer und Bronze sowie Hartkunststoff. Ist der geschliffene Bohrer auch für Handbohrmaschinen geeignet? Ja, die kurze Ausführung und der Zylinderschaft machen den MetavCUT Kurzbohrer für Handbohrmaschine geeignet, vorausgesetzt, die Maschine bietet ausreichende Spannqualität und Rundlaufgenauigkeit. Warum empfiehlt sich die TIN‑Beschichtung? Die TIN‑Beschichtung reduziert Reibung und Verschleiß, erhöht die Standzeit und verbessert die Wärmebeständigkeit beim Bohren in metallische Werkstoffe. Wofür steht die Norm DIN 338 bei diesem Bohrer? DIN 338 beschreibt kurze Spiralbohrer mit Zylinderschaft und legt Maße, Toleranzen und Ausführungsformen fest; bei diesem Produkt garantiert die Norm Kompatibilität und Serienstabilität.
7.9mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short HSS drill, 7.9 mm, 118°, black, DIN 338 (MetavCUT) The Twist Drill Type N is a short HSS metal drill designed for precision drilling in steel and non-ferrous materials, compatible with standard Drilling Machines and handheld units. Short HSS design for increased stability 7.9 mm diameter with 118° tip for reliable centring Conforms to DIN 338 for short twist drills Type N Normal spiral optimised for metal drilling Black finish for clear visual contrast during machining Long-lasting HSS construction for demanding metalwork Deriving strength from High Speed Steel (HSS), this short twist drill combines elasticity and toughness to resist breakage when machining small diameters. The HSS composition makes the tool especially suitable for drilling in alloyed and unalloyed Steel, Cast Iron, Non-Ferrous Metals and various Plastics, while retaining the ability to be resharpened easily. This focus on material quality results in a tool that offers predictable wear behaviour and extended service life for repetitive metalworking tasks. Improved precision thanks to short design and 118° tip A shorter overall length reduces overhang and bending, delivering greater Stability and more accurate hole positioning during high-precision operations. The 118° tip angle favours fast penetration and improved centring on curved or softer surfaces, making it a practical choice when consistent hole geometry is required. Together, the short execution and the tip geometry minimise deviation and chatter, which increases first-pass accuracy in production or repair work. Optimised for metal: Type N spiral and DIN 338 compliance The Normal spiral of Type N is a classic geometry tailored to metal drilling: it balances efficient chip removal with robust cutting edges. Conformance to DIN 338 clarifies that this is a short twist drill with a cylinder shank manufactured to industry standards, ensuring interchangeability and reliable performance in both stationary and portable drilling equipment. For tasks involving drilled holes in metal components, this configuration offers a dependable combination of repeatability and tool life. Practical compatibility and recommended uses Designed for use in standard Drilling Machines and handheld devices, the drill’s 7.9 mm diameter and 117 mm total length make it well suited for through-holes and shallow-depth bore operations up to typical industrial limits. The short spiral length improves rigidity for tougher alloys and reduces wobble when drilling from the face of the workpiece. This makes the tool appropriate for maintenance, prototyping and small-batch production where precision and resilience are required. Who benefits from this drill Machinists, maintenance technicians and workshop professionals engaged in metal fabrication and repair will value the balance of Precision and durability offered by this short HSS twist drill. Its suitability for a range of steels and non-ferrous materials, together with easy resharpening, supports cost-effective tool management and predictable machining results even under frequent use. Strong recommendation: For precise metal drilling choose the MetavCUT Twist Drill Type N — contact METAV Werkzeuge for full technical advice and order support at info@metav-werkzeuge.com or +49 2822 7131930; WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 40079-FDA Diameter: 7.9 mm Spiral length: 75 mm Total length: 117 mm Tip angle: 118° Material: HSS (High Speed Steel) Execution: short Type: Type N Colour: black Application: Drills for metal Compatible machine: Drilling Machine / Hand Drilling Machine Standard: DIN 338 Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill (MetavCUT, Type N) best used for? The MetavCUT Twist Drill Type N is primarily applied to the machining of high-strength materials and larger drill diameters in metalworking. Its design allows for straightforward resharpening and it withstands greater loads, making it suitable for alloyed and unalloyed Steel, Cast Iron, Non-Ferrous Metals and Plastics. Which three drill types exist? The main categories are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill Type N belongs to the metal drill group optimised for steel and related materials. Why are Twist Drills pointed? Pointing reduces the cross-cut at the tip of the Twist Drill, significantly lowering friction and thus requiring smaller feed forces. At the same time the sharpened tip improves centring in the workpiece for more accurate hole starts with the MetavCUT Type N. Can the Twist Drill (MetavCUT, Type N) be used for wood drilling? A metal drill such as the MetavCUT Twist Drill Type N can be used in wood, but guidance and finish are usually inferior compared with dedicated wood bits. Metal drills are easier to resharpen and tend to have less self-feed in wood. For which drilling depths is a Twist Drill most commonly used? A solid bore is typically performed with a Twist Drill. For diameters up to about 20 mm and drilling depths up to 100 mm a Twist Drill is the most frequently used tool, including the MetavCUT Type N configuration. Is HSS or HSSE better? The general assumption that HSSE steels are always superior to HSS is incorrect. Assess working conditions carefully to decide whether the higher purchase price of HSSE is justified; for many standard metal drilling tasks the MetavCUT HSS answer is appropriate.
7.9mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — MetavCUT short HSS‑E, Ø 7.9 mm, 135°, 5% cobalt‑alloyed, DIN 338, fully ground A Twist Drill (Type N) designed for precision metalworking with a short, fully ground shank and a 135° tip angle for reliable centring in hard materials. Precision short design for stable drilling in metal 7.9 mm diameter for versatile metal applications 135° tip for improved centring in hard materials HSS‑E with 5% cobalt for superior wear resistance Fully ground shank for high runout accuracy Durable material for demanding metalwork and longer tool life The MetavCUT Twist Drill is made from HSS‑E with 5% cobalt‑alloyed composition, a combination that increases red hardness and wear resistance under elevated temperatures. This material choice improves tool life when machining alloyed and unalloyed steel, cast iron and non‑ferrous metals. The short design further reduces bending stress, so the drill sustains higher loads with less risk of breakage during demanding operations. Stable geometry and tip angle for accurate holes A 135° tip angle and classic fluting geometry ensure the drill centres reliably and reduces walking on hard surfaces such as stainless steel. The Type N normal spiral makes this tool suitable primarily for metalworking, providing a balance between chip evacuation and cutting edge strength. For operators this means cleaner entry holes, reduced rework and more predictable drilling performance in workshop environments. Suited for professionals who prioritise precision and repeatability Designed for use in a Drilling Machine or compatible hand drills, the short Twist Drill is ideal where stability and precision matter, such as jig work, production runs and machine shop tasks. Professionals benefit from the reduced overhang and higher rigidity: fewer deviations in hole geometry and improved repeatability when drilling series of components. The fully ground shank contributes to consistent clamping and low runout on collets and chucks. Conforms to DIN 338 and built for easy handling and maintenance Manufactured to DIN 338 for short twist drills with cylindrical shank, this tool follows recognised dimensions and tolerances, easing tool selection and replacement in professional settings. The fully ground flutes produce sharp cutting edges and excellent concentricity, while the short configuration simplifies cooling and reduces chatter. For best results use appropriate coolant and moderate speeds for the material to extend service life. We recommend the MetavCUT Twist Drill Type N for precision metalworking — contact METAV Werkzeuge for expert advice and personalised support via info@metav-werkzeuge.com, call +49 2822 7131930 or WhatsApp +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47079-FDA Diameter: 7.9 mm Tip angle: 135° Type: Type N Execution: Short Colour/material treatment: 5% cobalt‑alloyed Shank execution: Fully ground Spiral length: 75 mm Overall length: 117 mm Material: HSS‑E Norm: DIN 338 Model series: Standard Line Application: Drills for metal For use with: Drilling Machine / Hand drill Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is a Twist Drill used for? The MetavCUT Twist Drill (Type N) is mainly applied to the machining of high‑strength materials and larger drill diameters; its design allows straightforward regrinding and it withstands higher loads. This makes the tool suitable for metalworking tasks where robustness and the ability to be resharpened are important. What are the three main drill types? Typical drill categories are metal drills, wood drills and stone/concrete drills. The MetavCUT Twist Drill (Type N) falls into the metal drill class and is optimised for use in steel, cast iron and similar materials.
7.9mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N, Diameter 7.9 mm, 135° Point, Short, Bright Finished, Fully Ground Shank, HSS‑G, DIN 338 by MetavCUT A short Twist Drill (Type N) designed for precise metal drilling in Drilling Machines and industrial workshop applications. Short design for high stability and precision 135° tip for harder materials and reduced wander HSS‑G ground geometry for faster drilling and less feed force Fully ground shank for excellent runout accuracy Conforms to DIN 338 for short cylindrical shank drills Precision and stability for demanding metalwork The short execution of this Twist Drill delivers significantly reduced overhang, which increases Stability and minimises bending during cutting. That compact geometry together with a 135° point reduces the initial skidding when entering hard materials, allowing more accurate positioning and cleaner holes. For workshop professionals this means fewer re‑drills and consistent hole quality when working with alloyed and unalloyed steels. Faster cutting and lower operator effort thanks to HSS‑G The HSS‑G (ground) material and CNC‑ground flute geometry provide sharper cutting edges and a high Rundlaufgenauigkeit, enabling up to 40% faster drilling with roughly 50% lower feed force compared with conventional HSS variants. For operations in Steel, Cast Iron, Sintered Iron and other non‑ferrous metals, this translates into shorter cycle times and less operator fatigue, particularly in repetition tasks on production benches or machine tools. Engineered shank and finish for machine compatibility With a fully ground shank and bright finished coating, the drill achieves excellent clamping accuracy and smooth insertion into chucks. The nominal Spiral Length of 75 mm and an Overall Length of 117 mm balance chip evacuation and stiffness. Use in stable chucks or machine tool setups is recommended to exploit the drill’s precision; the robust finish also eases handling and reduces corrosion risk in workshop environments. Recommended users and application scenarios This product targets machinists, toolrooms and maintenance professionals who require precise, repeatable metal drilling. The Type N normal spiral geometry is optimised for metalworking and is particularly effective when used with stationary drilling machines or robust portable drilling equipment under controlled conditions. For demanding tasks such as stainless steel or tempered components, the short Twist Drill offers reliability and a longer life under appropriate cooling. For precise metalworking choose MetavCUT’s Twist Drill Type N — if you are unsure whether this tool meets your needs or require further technical data, METAV Werkzeuge offers competent advice: info@metav-werkzeuge.com | Tel. +49 2822 7131930 | WhatsApp +49 170 2837271 Designation: Twist Drill Marke: MetavCUT SKU: 45079-FDA Diameter: 7.9 mm Overall length: 117 mm Spiral length: 75 mm Point angle: 135° Type: Type N Execution: Short Shank: Fully ground Material: HSS‑G Finish: Bright finished Application: Drills for metal; suitable for Drilling Machine use Standard: DIN 338 Model series: Standard Line Colour: Bright finished Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ Can I use the MetavCUT Twist Drill Type N in a hand drill? The MetavCUT Twist Drill Type N is optimised for machine use and offers best results when used in stable chucks or drilling machines; however, it can be used in powerful hand drills for light tasks if proper clamping, low speeds and cooling are applied to maintain precision and avoid breakage. For what is a Twist Drill used? The Twist Drill by MetavCUT is primarily applied to machining high‑strength materials and larger bore diameters; its ground geometry is easy to re‑sharpen and withstands substantial loads, making it suitable for alloyed and unalloyed steel, cast irons and hard plastics. Which 3 drill types exist? For reference, the main drill categories are Metal drills, Wood drills and Masonry/Concrete drills, and the MetavCUT Twist Drill belongs to the Metal drill group.
7mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Nutzen Sie die Kombination aus Stabilität durch HSS, Normgerechtigkeit nach DIN 338 und kurzer Ausführung für präzise Metallbohrungen. Bestellen Sie den Spiralbohrer direkt bei Metav oder lassen Sie sich telefonisch beraten. Spiralbohrer (HSS, Typ N) von MetavCUT Spiralbohrer von MetavCUT für Metallbearbeitung: kurzer HSS-Bohrer nach DIN 338 für präzise und stabile Bohrungen in Stahl und Nichteisenmetallen. Spiralbohrer von MetavCUT, HSS-Typ N Kurze Ausführung für erhöhte Stabilität Normgerecht nach DIN 338 Spitzenwinkel 118° für Metallanbohrung Zylinderschaft für Handbohrmaschine Präzision und Stabilität für anspruchsvolle Metallarbeiten Der kurze HSS-Bohrer bietet hohe Stabilität dank reduzierter Auskraglänge und rollgewalzter Fertigung. Dadurch sinkt die Neigung zum Verbiegen, was saubere, konzentrische Bohrungen in legierten und unlegierten Stählen ermöglicht. Nutzer profitieren von geringerer Bruchgefahr bei kleinen Durchmessern und einer zuverlässigen Wiederholgenauigkeit bei Serien von Einzelteilen. Materialkunde erklärt: HSS und Spitzenwinkel HSS steht für Schnellarbeitsstahl und kombiniert Zähigkeit mit Wärmebeständigkeit, wodurch der Bohrer besonders elastisch bleibt. Ein Spitzenwinkel von 118° ist optimal, um Metall sicher anzubohren und das Zentrieren zu erleichtern. Die Wahl dieser Geometrie reduziert das Ausbrechen an Ein- und Austritt und sorgt für saubere Bohrkanten bei dünnen bis mittleren Werkstoffen. Anwendungsfelder und empfohlene Einsätze Der Bohrer eignet sich für allgemeine Werkstattarbeiten, Instandsetzung und Montage an Handbohrmaschinen sowie stationären Maschinen. Er ist ideal für Bohrungen in Baustahl, Aluminium, Gusseisen und Kunststoffen, wenn Stabilität und Präzision im Vordergrund stehen. Bei Tiefbohrungen oder sehr harten Werkstoffen empfiehlt sich eine abgestufte Vorgehensweise oder speziell beschichtetes Werkzeug. Handhabung, Sicherheit und Lebensdauer Der Zylinderschaft vereinfacht den Wechsel in handelsüblichen Spannfuttern und minimiert Laufspiel. Kurze Ausführung und rollgewalzte Oberfläche verringern Spanverfestigung und Förderung von Spannungsrissen. Zur Verlängerung der Lebensdauer empfiehlt sich passende Schnittgeschwindigkeit und bedarfsgerechte Kühlung; bei hoher Belastung sorgen angepasste Vorschübe für gleichmäßigen Spanabtransport. Bestellen Sie den MetavCUT HSS Spiralbohrer für präzise Stahlbohrungen direkt bei Metav und nutzen Sie unsere Beratung per Telefon +49 2822 7131930 oder per eMail info@metav-werkzeuge.com Technische Daten Fakten Artikelnummer: 40070-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Ausführung: kurz Typ: Typ N Norm: DIN 338 Material: HSS Werte Durchmesser: 7 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 118° Verpackungseinheit: 10 Besonderheiten Farbe: schwarz Für Bohrmaschine: Handbohrmaschine HSS: Schnellarbeitsstahl, zäh und hitzebeständig DIN 338: Norm für kurze Spiralbohrer mit Zylinderschaft FAQ Welche Materialien kann ich mit dem MetavCUT Spiralbohrer bearbeiten? Der MetavCUT Spiralbohrer aus HSS eignet sich für legierten und unlegierten Stahl, Gusseisen, Aluminium und Kunststoffe; bei sehr harten Stählen sind spezialisierte Werkzeuge empfehlenswert. Ist die kurze Ausführung für Handbohrmaschinen geeignet? Ja, die kurze Ausführung reduziert Auskragung und erhöht die Stabilität, wodurch der Bohrer für Handbohrmaschine und stationäre Maschinen gleichermaßen geeignet ist. Welchen Einfluss hat der Spitzenwinkel von 118°? Ein Spitzenwinkel von 118° erleichtert das Zentrieren und minimiert Ausbruch bei Ein- und Austritt, was besonders bei dünnen Werkstücken zu saubereren Bohrkanten führt. Wofür steht die Norm DIN 338 bei diesem Bohrer? DIN 338 bezeichnet kurze Spiralbohrer mit Zylinderschaft und legt Maße, Ausführungen und Fertigungsverfahren fest, wodurch Austauschbarkeit und Qualitätsstandards gewährleistet sind. Welche SKU hat der Bohrer für die Bestellung? Die SKU lautet 40070-FDA und kann bei Bestellung oder Anfrage angegeben werden, um das Produkt schnell zu identifizieren.
7mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Twist Drill (Type N) — 7 mm, 135° tip, short, 5% cobalt-alloyed, HSS‑E, DIN 338 by MetavCUT The Twist Drill Type N is a short, fully ground metalworking drill for Drilling Machine use, optimised for precise holes in hard materials and professional shop environments. Short design for higher stability 7 mm diameter for standard metal holes 135° tip angle for harder materials like stainless steel HSS‑E with 5% cobalt for improved wear resistance Precision and stability for accurate metal holes The short execution of this Twist Drill reduces overhang and thus significantly lowers the tendency to bend or wander during machining, delivering higher stability and improved concentricity. With a Spiral Length of 69 mm and a Total Length of 109 mm, the reduced cantilever ensures cleaner holes and better roundness when used in stationary or bench Drilling Machines. This geometry is particularly beneficial for tasks that demand repeatable accuracy and minimal rework. Material composition and cutting behaviour for demanding tasks Manufactured from HSS‑E with a 5% cobalt alloy, the drill provides increased hardness and thermal resistance compared with standard HSS, improving tool life under higher cutting temperatures. The fully ground flute geometry yields sharp cutting edges and excellent runout accuracy, while the 135° tip angle optimises entry into harder materials by reducing initial cutting forces. For workshop users, this means more reliable performance when drilling alloyed and unalloyed steel, cast iron and many non‑ferrous metals. Intended uses and practical advice for best results This Type N Twist Drill is designed primarily as a metal drill for professional metalworking applications. It is well suited for use in Drilling Machines for through‑holes and precision fits. For optimal results, a stable clamping setup and appropriate cutting fluid are recommended, especially when working with stainless steels or when long continuous cuts are needed. As the fully ground variant can be more brittle than rolled versions, controlled feed and adequate cooling extend service life and reduce breakage risk. Who benefits from this tool Workshops, toolrooms and metal fabricators who require repeatable, precise holes will value the balance of durability and accuracy this short HSS‑E Twist Drill offers. The combination of Type N spiral geometry and cobalt enrichment addresses the needs of professionals drilling harder materials while maintaining the option to work with various non‑ferrous metals and plastics as required. Strongly recommended: Choose the MetavCUT Type N Twist Drill for demanding metal drilling tasks and contact METAV Werkzeuge for expert application support — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 • WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 47070-FDA Diameter: 7 mm Total Length: 109 mm Spiral Length: 69 mm Tip Angle: 135° Type: Type N Execution: short Shaft Execution: fully ground Material: HSS‑E Colour: 5% cobalt-alloyed For: Drilling Machine Model Series: Standard Line Norm: DIN 338 Applications: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill used for? The MetavCUT Type N Twist Drill is primarily applied to the machining of high‑strength and standard steels and larger drill diameters; its short form is ideal for precision work in metal, offering easier grinding and greater resistance to mechanical stress. Can the MetavCUT Type N Twist Drill be used in a drilling machine? Yes, the MetavCUT Type N Twist Drill is intended for use in Drilling Machines and performs best when clamped in stable chucks or fixtures under controlled feed and with cutting fluid where applicable. Why are twist drills point‑sharpened? Point‑sharpening reduces the cross‑cutting edge at the tip of the Twist Drill, lowering frictional forces and therefore requiring less feed force; the sharper tip also improves centring accuracy in the workpiece. Can a metal twist drill be used to drill wood? A metal Twist Drill such as the MetavCUT Type N can be used in wood, but guidance and surface finish are typically inferior to dedicated wood drills; metal drills are easier to re‑grind and have lower self‑feeding tendencies. At which drill depths is the Twist Drill most commonly used? For solid drilling, the Twist Drill is the most frequently used tool; it is particularly common for diameters up to 20 mm and drilling depths up to 100 mm, depending on machine setup and material. Which is better, HSS or HSSE? The common assumption that HSSE steels are always superior to HSS is not universally true; selection should be based on actual working conditions, as HSSE may only justify higher cost under specific stress and temperature regimes.
7mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra-long HSS‑G 7 mm, 135° point, bright‑finished, fully‑ground shank, DIN 1869 (MetavCUT) The Twist Drill is an extra‑long HSS‑G drill designed for deep metal drilling with a Drilling Machine, offering precise performance for demanding workshop and industrial applications. Extra‑long design for deep bores HSS‑G material for high cutting performance 135° point angle for harder materials Fully ground shank for high concentricity DIN 1869 specification for deep‑hole drilling Durable HSS construction for reliable metal cutting The HSS‑G material and CNC ground flute geometry deliver a robust combination of hardness and sharpness that makes the Twist Drill ideal for metalworking. Ground manufacturing creates very sharp cutting edges and excellent Runout Accuracy, so holes are cleaner and reaming effort is reduced. Because ground drills can be comparatively brittle, the drill performs best under machine conditions and with appropriate Coolant to extend tool life. Designed for deep, precise boreholes in tough materials With an overall length of 225 mm and a spiral length of 155 mm, this extra‑long twist drill reaches deep workpieces where standard lengths cannot. The 7 mm diameter combined with a 135° point angle improves entry in harder steels and stainless materials, reducing the risk of wandering at the start of the bore. Conformity to DIN 1869 ensures suitability for deep‑hole conditions and industrial standards, enabling consistent results in production environments. Best used in machine setups for professional results This twist drill is optimised for use with a Drilling Machine rather than handheld use, thanks to its fully‑ground shank and precision geometry. Professionals in fabrication, maintenance and toolrooms will benefit from faster penetration and lower feed forces—features that support efficient workshop workflows. For stationary drilling rigs or press machines, the drill’s geometry allows better centring and repeatable hole quality. Faster drilling and lower operator effort Testing and manufacturer guidance show that the ground HSS design can enable up to 40% faster drilling and require about 50% less thrust than conventional rolled HSS tools in comparable conditions. That translates into reduced machine load and less operator fatigue during repetitive work. Keep in mind that the extra‑long geometry is specifically targeted at deep or hard‑to‑reach bores and performs best with steady clamping and adequate lubrication. We recommend the MetavCUT extra‑long Twist Drill for professionals needing precise deep metal bores; for personalised technical advice and application support contact METAV Werkzeuge via email, phone or WhatsApp — expert consultation is available to ensure the right tool choice and safe handling 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Twist Drill Brand: MetavCUT SKU: 32070-FDA Diameter: 7 mm Point Angle: 135° Execution / Type: Extra long Colour: Bright finished Overall Length: 225 mm Spiral Length: 155 mm Shank Execution: Fully ground Material: HSS‑G Standard / Norm: DIN 1869 Application: Drills for metal, for Drilling Machine Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill is primarily used for machining high‑strength metals and larger drill diameters; its extra‑long design and ground geometry make it suitable for deep bore operations and difficult‑to‑access drilling tasks in professional metalworking. Which three drill types are commonly distinguished? The three main drill types are Metal drills, Wood drills, and Masonry/Concrete drills, where the MetavCUT Twist Drill belongs to the metal drill category and is optimised for metalworking applications.
7mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Twist Drill — Extra Long Drill Bit (7 mm, 135°) HSS‑G, Bright Finished, DIN 1869 — MetavCUT A Twist Drill extra long HSS‑G drill bit for Drilling Machines, designed for deep metal drilling and precise holemaking. 7 mm diameter for precision metalwork Extra long design for deep bore applications Fully ground shank for high concentricity HSS‑G material for hard metals and longevity 135° tip angle reduces walking in tough materials Faster deep drilling thanks to extra long design The extra long overall length delivers the reach required for deep drilling tasks without the need to reposition workpieces, making the bit ideal for access-restricted setups. Made from HSS‑G, this Twist Drill combines hardness with a ground geometry that produces clean, precise holes in steel and cast materials; the CNC grinding process yields sharp cutting edges and high runout accuracy, which shortens machining time and improves repeatability. Reliable penetration in hard materials with 135° tip A 135° tip angle provides a more gradual cutting action suited to harder alloys and stainless steels, lowering the risk of chipping at the entry and improving centering when starting a hole. This geometry reduces the need for pilot operations in many cases and helps maintain edge life under elevated contact stresses, so fewer tool changes are necessary during a job. Clean chips and better cooling for extended tool life The deep spiral flute (spiral length 200 mm) evacuates swarf efficiently from deep bores, while the bright finished surface supports smoother chip flow and easier cleaning. When used with appropriate coolant and a stable setup on a Drilling Machine, the combination of flute geometry and fully ground shank minimizes heat build-up and supports longer service intervals for the cutting edge. Precise guidance and handling in production environments The fully ground shank (fully ground) ensures excellent concentricity and stable clamping, reducing vibration and improving surface quality of the bore. Consciously engineered to DIN 1869 tolerances, this Twist Drill is suited for workshop and production use where consistent hole quality and interchangeability are required. Who benefits from this drill and how to use it Designed primarily for machining professionals and maintenance technicians working with legierter and unlegierter steels, cast iron and non‑ferrous metals, this bit excels where deep, accurate holes are required. For best results, secure the workpiece, use a stable Drill Machine setting, apply suitable coolant, and avoid excessive feed to prevent brittle fracture typical of ground HSS tools. METAV CUT recommends this Twist Drill for demanding deep metal drilling tasks; for personalised technical advice or to verify suitability for a specific application, METAV Werkzeuge offers expert consultation — Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Designation: Twist Drill (Spiralbohrer) Brand: MetavCUT SKU: 33070-FDA Diameter: 7 mm Overall length: 290 mm Spiral length: 200 mm Tip angle: 135° Material: HSS‑G Standard: DIN 1869 Finish: Bright finished Shank execution: Fully ground Execution: Extra long For: Drilling Machine Model series: Standard Line Application: Drills for metal Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the Twist Drill by MetavCUT best used for? The MetavCUT Twist Drill is primarily used for machining high‑strength materials and larger drill diameters; its extra long configuration and HSS‑G grade make it well suited for deep holes in legierte and unlegierter steel, cast iron and hard plastics, providing clean, precise bores under demanding conditions. Can the MetavCUT Twist Drill be used with a regular drilling machine? Yes, this MetavCUT Twist Drill is designed for use in a Drilling Machine; for optimal performance secure the bit in a precise chuck, apply appropriate coolant and moderate feed rates to exploit the ground geometry and avoid undue stress on the cutting edge. What are Twist Drills used for? Twist Drills are mainly applied to the machining of high‑strength materials and larger drill diameters; their shape makes them easy to sharpen and capable of withstanding significant loads. Which three drill types exist? There are three common categories: metal drills, wood drills and masonry/concrete drills. Why are Twist Drills sharpened? Sharpening reduces the cross‑cut at the tip, lowering friction and thus the required feed forces; it also improves centring at the start of the hole, giving better guidance and less wander. Can metal Twist Drills be used to drill wood? Metal Twist Drills can be used in wood, but they generally offer less guidance and a less clean finish than dedicated wood drills; however, they are easier to resharpen and exhibit less self‑feeding tendency. At what drilling depths are Twist Drills most commonly used? Twist Drills are the go‑to tool for through drilling in solid materials; they are most frequently used for diameters up to about 20 mm and depths up to around 100 mm. Is HSS or HSSE better? The common assumption that HSSE is categorically superior to HSS is not universally true; when choosing, assess whether your working conditions justify the higher cost of HSSE for improved wear resistance in specific applications.
7mm HSS-G Twist Drill DIN 1869 ,extra long, bright finished - MetavCUT
Profitieren Sie von der Kombination aus schneller Schneidgeometrie und extra langer Bauform: Der geschliffene HSS-G Spiralbohrer liefert präzise, saubere Bohrungen in legiertem und unlegiertem Stahl, während die Norm DIN 1869 Verlässlichkeit bei tiefen Bohrungen sicherstellt. Bestellen Sie den Bohrer bequem direkt bei Metav und lassen Sie sich bei technischen Fragen von unserer Beratung unterstützen. Spiralbohrer 34070-FDA — extra lang, HSS-G Der Spiralbohrer 34070-FDA ist ein extra langer HSS-G-Bohrer für tiefe Metallbohrungen mit hoher Rundlaufgenauigkeit. Spiralbohrer «34070-FDA» von MetavCUT HSS-G geschliffen für präzise Metallbohrungen Extra lang: Gesamtlänge 370 mm, Spirallänge 250 mm Spitzenwinkel 135° für harte Werkstoffe Norm DIN 1869, Verpackungseinheit 10 Tiefe Bohrungen mit geringem Kraftaufwand für produktive Werkstätten Der geschliffene HSS-G Bohrer wurde für tiefe Bohrungen entwickelt und bietet durch die längere Arbeitslänge echte Praxisvorteile bei schwer zugänglichen Stellen. Durch die geschliffene Geometrie reduziert sich die erforderliche Anpresskraft um bis zu 50 %, was die Belastung von Handbohrmaschine und Anwender verringert. Gleichzeitig ermöglicht die optimierte Spanführung saubere Bohrbilder und verkürzt die Bearbeitungszeit um bis zu 40 %. Diese Kombination erhöht die Effizienz bei Reparatur- und Instandsetzungsarbeiten erheblich. Präzision und Materialverträglichkeit für anspruchsvolle Werkstoffe Mit einem Spitzenwinkel von 135° dringt der Bohrer kontrolliert in härtere Werkstoffe ein und eignet sich für legierten sowie unlegierten Stahl bis 1000 N/mm². Die geschliffene Schaftausführung sorgt für hohen Rundlauf und exakte Bohrungen, ideal wenn Maßhaltigkeit zählt. Für beste Ergebnisse empfiehlt sich das Anpunkten vor dem Bohren und der Einsatz von Kühlschmierstoff bei zähen Materialen, um Lebensdauer und Genauigkeit weiter zu steigern. Einsatzbereich und Anwendernutzen für Werkstatt und Montage Der Bohrer fällt in den Standard-Bereich für Durchmesser und ist besonders geeignet für den Einsatz in Handbohrmaschine sowie stationären Säulenbohrmaschinen. Anwender profitieren von der Extra-Länge bei tiefen Bohrungen oder bei Arbeiten an langen Bauteilen. Die Spirallänge 250 mm ermöglicht effiziente Spänetransport bei moderaten Tiefen; dennoch sind bei sehr tiefen Sacklochbohrungen zusätzliche Maßnahmen wie Vorschubkontrolle und Kühlung empfohlen. Hinweise zur Handhabung und Lagerung für lange Standzeiten Da geschliffene HSS-G Werkzeuge eine sehr scharfe Schneide bieten, sollten Stöße und Verkantungen vermieden werden, um Bruchrisiken zu minimieren. Bei stationärem Einsatz und kontrollierter Kühlung entfaltet der Bohrer sein volles Potenzial. Die Blank-Oberfläche verlangt keine besondere Oberflächenbehandlung, jedoch schützt sachgerechte Lagerung vor Korrosion und mechanischer Beschädigung, wodurch sich die Lebensdauer merklich verlängert. Greifen Sie auf den geschliffenen HSS-G Spiralbohrer von MetavCUT zurück und bestellen Sie über Metav; bei offenen Fragen erreichen Sie unsere Techniker per eMail info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 Produktmerkmale Artikelnummer: 34070-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Ausführung: extra lang Material: HSS-G Norm: DIN 1869 Farbe: blank Daten Durchmesser: 7 mm Gesamtlänge: 370 mm Spirallänge: 250 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten Schaftausführung: geschliffen Einsatz: Handbohrmaschine HSS-G: geschliffen, hohe Schnittschärfe DIN 1869: Tieflochspirale für extra tiefe Bohrungen FAQ Für welche Materialien ist der Bohrer geeignet? Der MetavCUT Spiralbohrer 34070-FDA aus HSS-G eignet sich für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle und Hartkunststoff; bei sehr harten Werkstoffen ist auf passende Kühlung zu achten. Kann der Bohrer in einer Handbohrmaschine verwendet werden? Ja, der Spiralbohrer 34070-FDA ist für den Einsatz mit Handbohrmaschine geeignet; für beste Präzision empfiehlt sich Anpunkten und kontrollierter Vorschub. Wie tief kann man mit diesem Bohrer sicher arbeiten? Die extra lange Ausführung mit Gesamtlänge 370 mm und Spirallänge 250 mm ist für tiefe Bohrungen ausgelegt; bei sehr tiefen Sacklöchern sind mehrstufiges Bohren und Kühlung ratsam. Ist dieser Bohrer für Serienfertigung geeignet? Der MetavCUT Spiralbohrer 34070-FDA ist für Werkstatt- und Serienarbeiten im mittleren Umfang geeignet; bei hohen Stückzahlen in gehärtetem Stahl sind Vollhartmetallwerkzeuge wirtschaftlicher. Welche Vorteile hat die geschliffene Ausführung gegenüber gewalzten Bohrern? Geschliffene Spiralbohrer (HSS-G) bieten schärfere Schneiden, bessere Rundlaufgenauigkeit und sauberere Bohrbilder, sind aber empfindlicher gegenüber Stoß- und Kippbelastung und profitieren von stationärem oder gut kontrolliertem Einsatz.
7mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill (Type N) — 7 mm, 135° Point Angle, Short, Bright finished, HSS-G, DIN 338 A Twist Drill (Type N) designed for precise metal drilling in Drilling Machines, offering a short, stable geometry for work on hard materials. Short design for improved stability HSS-G material for high cutting performance 135° point angle for hard materials Fully ground shank for excellent runout accuracy Durable HSS-G construction for faster, cleaner holes The HSS-G material of this Twist Drill ensures high wear resistance and reliable cutting behaviour when machining Steel and other Alloys. Because the flute geometry is produced by CNC grinding, the tool achieves very sharp cutting edges and a high concentricity, which translates into cleaner holes and longer tool life under correct cutting conditions. Users will benefit from up to 40% faster drilling and about 50% less feed force compared with conventional HSS designs, provided adequate coolant and appropriate speeds are used. Short overall length increases precision and reduces vibration A shorter design reduces the exposed overhang and therefore minimizes bending and chatter during operation. This results in higher positional accuracy and makes the drill particularly suitable for precise work in hardened materials such as Stainless Steel. The designation to DIN 338 confirms the geometry and format as a short Twist Drill with a Cylindrical Shank, ensuring compatibility with common chucks and fixtures in metalworking shops. Geometry optimised for metalworking and hard materials The 135° point angle is tailored to reduce initial drilling forces and improve centring in tough materials, shortening pilot time and improving surface finish in the hole. As a Type N (normal spiral) drill, this tool is engineered primarily for Metal applications including Cast Iron, Sintered Iron, Tempered Castings, Non-Ferrous Metals and Hard Plastics. For best results, use on stationary or machine-mounted Drilling Machines and apply appropriate cooling to avoid tempering the cutting edge. Target users and handling recommendations Workshop professionals, toolroom technicians and demanding hobbyists will appreciate the combination of a short flute length and a fully ground shank that delivers consistent runout and repeatable hole quality. To avoid brittleness-related breakage, operate the Twist Drill with steady feed, adequate coolant and secure clamping. Ground drills can be re-sharpened more easily than rolled equivalents, maintaining edge quality and service life when reconditioned correctly. We recommend the MetavCUT Twist Drill for precise metalworking applications; for technical advice or to confirm suitability for a specific material or machine, METAV Werkzeuge provides expert consultation – eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 | WhatsApp: +49 170 2837271 Designation: Twist Drill Brand: MetavCUT SKU: 45070-FDA Diameter: 7 mm Point Angle: 135° Type: Type N Execution: Short Finish: Bright finished Shank Execution: Fully ground Material: HSS-G Norm: DIN 338 Spiral Length: 69 mm Total Length: 109 mm For Drilling Machine: Drilling Machine Application: Drills for metal Model Series: Standard Line Manufacturer: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What are Twist Drills used for? The MetavCUT Twist Drill is primarily used for machining high-strength materials and larger hole diameters. Its ground geometry is easy to re-sharpen and withstands higher loads, making it suitable for demanding metalworking tasks where durability and precision are required. Which three drill types exist? For context, the MetavCUT Twist Drill belongs to the metal-drill category. The three main drill types are Metal drills, Wood drills and Stone/Concrete drills.
7mm HSS-G Twist Drill DIN 338 ,short, TIN-coated, Type N - MetavCUT
Kombination aus hoher Standzeit durch TIN-Beschichtung und präziser HSS-G-Geometrie ermöglicht schnelle, saubere Bohrungen in Stahl und Nichteisenmetallen; die kurze Ausführung sorgt für zusätzliche Stabilität. Bestellen Sie den Spiralbohrer direkt über Metav oder fragen Sie unsere Beratung an. Spiralbohrer 7 mm von MetavCUT (kurze Ausführung, HSS-G) Der Spiralbohrer ist ein kurzer, geschliffener HSS-G-Bohrer nach DIN 338 für präzises Metallbohren in stationären und handgeführten Maschinen. Kurze Ausführung für erhöhte Stabilität TIN-Beschichtung für längere Lebensdauer Geschliffenes HSS-G: Präzise Bohrlöcher Spitzenwinkel 135°: ideal für harte Werkstoffe DIN 338-konform; Zylinderschaft, Typ N Stabilität und Präzision beim Metallbohren Dank der kurzen Bauform reduziert sich die Auskraglänge, wodurch sich die Stabilität beim Bohren deutlich erhöht. Die geschliffene Schneidgeometrie sorgt für scharfe Kanten und eine hohe Rundlaufgenauigkeit, was zu sauberen, maßhaltigen Bohrlöchern in Stahl, Temperguss und Gusseisen führt. Diese Eigenschaften machen den Bohrer zu einer belastbaren Wahl für präzise Fertigungsaufgaben. Höhere Effizienz bei geringerem Kraftaufwand Der geschliffene HSS-Bohrer ermöglicht ein bis zu 40 % schnelleres Bohren und benötigt dabei etwa 50 % weniger Anpresskraft als herkömmliche HSS-Varianten. Die TIN-Beschichtung reduziert Reibung und Verschleiß, besonders bei geeigneter Kühlung, und verlängert so die Standzeit. Das Ergebnis sind kürzere Bearbeitungszeiten und weniger Werkzeugwechsel in der Fertigung. Vielseitige Anwendung in Werkstatt und Produktion Als Produkt aus dem Standard-Bereich eignet sich der Bohrer für Werkstatt, Montage und anspruchsvolle DIY-Arbeiten. Er ist geeignet für dünne bis mittlere Bleche, Profile und Flachstahl sowie für Nichteisenmetalle wie Kupfer und Bronze. Die Kombination aus Typ N-Normalspirale und Zylinderschaft macht ihn praktikabel für Handbohrmaschine und stationäre Maschinen gleichermaßen, solange die Anwendung keine extrem tiefen Löcher über das fünffache des Durchmessers erfordert. Normkonforme Verarbeitung und Materialeigenschaften Die Fertigung nach DIN 338 und die Ausführung als HSS-G (geschliffen) garantieren definierte Qualitätsmerkmale: scharfe Spangebende Kanten und hohe Präzision. Als Typ N-Normalspirale ist der Bohrer für allgemeine Metallbearbeitung optimiert. Hinweis: Geschliffene Bohrer sind sehr leistungsfähig, können aber bei unsachgemäßer Handhabung spröder reagieren; Kühlung und stationäre Spannmittel erhöhen die Sicherheit. Empfehlung: MetavCUT Spiralbohrer mit TIN-Beschichtung für dauerhafte Präzision — Bestellbar über Metav, bei Fragen eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: 46070-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie / Baureihe: Standard Line Typ: Typ N Ausführung: kurz Farbe: TIN-beschichtet Material: HSS-G Norm: DIN 338 Für Bohrmaschine: Handbohrmaschine Schaft Ausführung: geschliffen Fakten Durchmesser: 7 mm Gesamtlänge: 109 mm Spirallänge: 69 mm Spitzenwinkel: 135° Verpackungseinheit: 10 Besonderheiten TIN-beschichtet: Titan-Nitrid-Beschichtung, erhöht Verschleißfestigkeit HSS-G: Geschliffener Schnellarbeitsstahl, sehr scharfe Kanten DIN 338: Norm für kurze Spiralbohrer mit Zylinderschaft Typ N: Normalspirale, klassisch für Metallbohrungen FAQ Für welche Materialien eignet sich der Bohrer besonders? Der MetavCUT Spiralbohrer in HSS-G mit TIN-Beschichtung eignet sich besonders für legierten und unlegierten Stahl, Gusseisen, Temperguss sowie Nichteisenmetalle wie Kupfer und Bronze. Passt der Bohrer in eine Handbohrmaschine? Ja, die Ausführung mit Zylinderschaft und die Angabe „Für Bohrmaschine: Handbohrmaschine“ machen den Spiralbohrer geeignet für handgeführte Geräte sowie stationäre Maschinen. Welche Vorteile bringt die TIN-Beschichtung? Die TIN-Beschichtung reduziert Reibung und Verschleiß, erhöht die Lebensdauer und verbessert die Wärmebeständigkeit beim Bohren in Metall. Warum ist die Ausführung „geschliffen“ relevant? Geschliffene HSS-G-Bohrer bieten höhere Schärfe und Rundlaufgenauigkeit, was zu präziseren Bohrlöchern führt; sie sind jedoch empfindlicher gegenüber schlagartigen Belastungen. Gibt es eine Modellbezeichnung oder SKU für Nachbestellungen? Die Artikelnummer des Spiralbohrers lautet 46070-FDA; diese SKU erleichtert Nachbestellungen und die Kommunikation mit Metav.
7mm HSS-G Twist Drill DIN 340 ,long, bright finished - MetavCUT
Twist Drill — 7 mm, 135° tip, long, bright finished, HSS‑G, DIN 340 The Twist Drill long HSS‑G 7 mm is built for deep metal drilling with a 135° tip, suited to hard materials and less accessible bore locations on a Drilling Machine. Long Twist Drill for deep, hard-to-reach holes HSS-G ground for faster drilling and precise holes 135° tip suited for hard materials like stainless steel Fully ground shank ensures high runout accuracy DIN 340 standard for long drill execution Faster deep drilling with reduced effort for workshop use Long execution according to DIN 340 offers clear practical benefits: the increased Spiral Length and overall length enable drilling into deeper workpieces or into recesses where standard bits fall short. Because the flute geometry is ground, the bit cuts with very sharp edges, which can result in up to 40% faster drilling and requires substantially lower feed pressure compared with conventional HSS bits. The practical effect is less operator fatigue, more consistent bore quality and a faster cycle time for repetitive metalworking tasks. Precise holes in hard materials thanks to HSS‑G and 135° tip A HSS‑G (ground high‑speed steel) blank combined with a 135° tip improves centring and reduces walking on harder substrates such as stainless steel. The ground geometry gives high Runout Accuracy and clean chip evacuation, producing more concentric and burr‑reduced holes. Users benefit from better repeatability and less post‑processing. Note that ground HSS bits can be more brittle than rolled types, so controlled feeds and appropriate coolant are advised to avoid chipping. Built for metalworking: materials and machine compatibility This long variant is intended primarily for metallic materials: alloyed and unalloyed steel, cast steels, grey and spheroidal cast iron, sintered iron, non‑ferrous metals and hard plastics. It is compatible with handheld Drilling Machines and bench drills when greater reach is needed. For drilling in steels up to the typical range of 900 N/mm² the geometry and tip angle help maintain performance while minimising chatter and deflection, delivering holes that meet machining tolerances in assembly and maintenance operations. Practical handling advice to extend service life and hole quality Because the flutes and cutting geometry are produced by grinding, re‑sharpening is straightforward and preserves cutting performance. For best results, use moderate cutting speeds, steady feed and regular cooling or lubrication to manage heat and chip formation. When drilling deep bores, peck drilling or intermittent withdrawal will improve chip evacuation and reduce risk of breakage. Store bits to avoid impact and inspect for wear before reuse to ensure continued precision. Strong recommendation: For demanding deep‑hole metal drilling choose the MetavCUT long HSS‑G Twist Drill for reliable performance; METAV Werkzeuge offers comprehensive technical advice and support — Email: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 53070-FDA Durchmesser: 7 mm Spitzenwinkel: 135° Ausführung: long Gesamtlänge: 156 mm Spirallänge: 102 mm Farbe: bright finished Schaft Ausführung: fully ground Material: HSS-G Norm: DIN 340 Für Bohrmaschine: Drilling Machine Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is this Twist Drill suitable for? The MetavCUT Twist Drill long 7 mm is suitable for metalworking tasks where deeper or less accessible holes are required; the HSS‑G ground geometry and 135° tip make it especially effective for alloyed and unalloyed steels, cast materials and hard plastics. Which three drill types exist? There are three common drill categories: metal drill bits, wood drill bits and stone/concrete drill bits; the MetavCUT Twist Drill belongs to the metal drill bit family and is optimised for that application. What is a Twist Drill used for? A Twist Drill is principally used for machining high‑strength materials and larger bore diameters; its shape is easy to re‑grind and it endures higher loads while keeping a sharp cutting edge.
8,5mm Spiralbohrer, 118° Spitzenwinkel, HSS, rollgewalzt, Morsekegelschaft, 168mm Gesamtlänge - MetavCUT
Der rollgewalzte HSS-Spiralbohrer überzeugt durch Zähigkeit, Spitzenwinkel 118° und den sicheren Morsekegel-Schaft. Nutzen Sie die Kombination aus Bruchfestigkeit, maschineller Aufnahme und genormter Ausführung für zuverlässige Metallbohrungen. Bestellen Sie den Bohrer direkt über Metav Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer HSS mit Morsekegel von MetavCUT Der Spiralbohrer von MetavCUT eignet sich für präzise Metallbohrungen in Ständerbohrmaschinen und wirkt besonders bruchsicher durch rollgewalzte Fertigung Spiralbohrer von MetavCUT für Metallbohrungen Rollgewalzte HSS-Ausführung, bruchzäh und elastisch Morsekegel-Schaft für feste Kraftübertragung DIN 345 Norm, geeignet für Ständerbohrmaschinen Spitzenwinkel 118° für effizientes Eindringen Hohe Zähigkeit und Materialvorteile für robuste Bohrarbeiten Dank der rollgewalzten Fertigung ist der HSS-Bohrer besonders zäh und weniger bruchanfällig als geschliffene Varianten unter rauen Einsatzbedingungen. Diese Herstellung macht den Bohrer elastischer, was beim Bohren von kleinen Durchmessern das Bruchrisiko verringert. Der Einsatz von HSS bietet eine gute Kombination aus Härte und Zähigkeit für legierte und unlegierte Stähle sowie Nichteisenmetalle. Präzise Kraftübertragung durch Morsekegel-Schaft Der konische Morsekegel-Schaft sorgt für feste Selbsthemmung in der Aufnahme und ermöglicht eine sichere Übertragung hoher Drehmomente an der Ständerbohrmaschine. Dadurch reduziert sich das Risiko von Verrutschen und erhöht die Standzeit des Werkzeugs. Für Anwender mit stationärer Maschine bedeutet das weniger Nacharbeiten und konstantere Bohrergebnisse. Anwendungsempfehlung und Einsatzbereiche Dieser Spiralbohrer eignet sich für allgemeine Metallarbeiten in Werkstatt und Industrie, insbesondere für Stahl, Guss und Kunststoffe bis zu etwa 900 N/mm² Festigkeit. Mit einem Spitzenwinkel von 118° dringt der Bohrer leicht in weichere Materialien ein und bietet zuverlässige Zentrierung auf gewölbten Flächen. Für beste Ergebnisse bei höheren Durchmessern empfiehlt sich abgestuftes Vorbohren. Auswahlkriterien und Tipps für den Einsatz Wer Wert auf Alltagstauglichkeit legt, profitiert von der DIN 345-Norm und der Standard Line Ausführung von MetavCUT. Für sauberes Spanbild und längere Standzeit empfiehlt sich passende Kühlung bei zähen Materialien und ein Voranpunktieren bei hoher Präzision. Die Gesamtlänge und Spirallänge sind so gewählt, dass die Handhabung in stationären Maschinen komfortabel bleibt. Empfehlung: Für verlässliche Metallbohrungen empfiehlt MetavCUT den HSS-Spiralbohrer mit Morsekegel; Bestellanfragen über Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 sind willkommen Produktmerkmale Artikelnummer: 54085-FDA Marke: MetavCUT Bezeichnung: Spiralbohrer Serie: Standard Line Fakten Durchmesser: 8,5 mm Gesamtlänge: 168 mm Spirallänge: 87 mm Spitzenwinkel: 118° Besonderheiten Ausführung: rollgewalzt — zäher, bruchsicherer Fertigungsprozess Material: HSS Schaft: Morsekegel — konischer Schaft mit Selbsthemmung, hohe Kraftübertragung Norm: DIN 345 Farbe: schwarz Anwendung: Bohrer für Metall Verpackungseinheit: 1 FAQ Für welche Materialien eignet sich der Bohrer am besten? Der Spiralbohrer von MetavCUT (SKU 54085-FDA) ist für legierte und unlegierte Stähle, Guss sowie Nichteisenmetalle und Kunststoffe geeignet und deckt typische Werkstattanforderungen zuverlässig ab. Welche Maschine ist für diesen Bohrer empfohlen? Empfohlen wird eine Ständerbohrmaschine mit Morsekegel-Aufnahme, da der konische Morsekegel-Schaft des MetavCUT-Bohrers eine feste, präzise Aufnahme und hohe Kraftübertragung ermöglicht. Ist der Bohrer geschliffen oder gewalzt? Die Ausführung ist rollgewalzt, was den Bohrer zäher und bruchsicherer macht und ihn besonders für normale Metallbohrarbeiten in Werkstatt und Montage prädestiniert. Wie tief kann mit dem Bohrer sicher gebohrt werden? Die effektive Nutzlänge wird durch die Spirallänge von 87 mm begrenzt; für besonders tiefe Löcher ist abgestuftes Aufbohren oder ein längerer Spezialbohrer empfehlenswert. Welche Rolle spielt der Spitzenwinkel 118°? Der Spitzenwinkel 118° erleichtert das Eindringen in weichere Materialien und verbessert die Zentrierung bei gewölbten Oberflächen, wodurch die Handhabung in vielen Alltagsanwendungen vereinfacht wird.
8.1mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
MetavCUT Twist Drill (Type N) — 8.1 mm · 118° tip · HSS · Short · Black · DIN 338 A MetavCUT Twist Drill (Type N) for precision metal drilling, designed as a short HSS drill for use with hand drilling machines. Short HSS construction for increased stability Precision 8.1 mm diameter for consistent hole quality 118° tip angle for reliable centring in metals Conforms to DIN 338 for standardised short twist drills Suitable for hand drilling machines and workshop use Stable, accurate holes for metalworking tasks The HSS material of this short twist drill offers a reliable balance of hardness and toughness for metalworking. Thanks to its short design, the tool exhibits reduced deflection and higher stability during drilling, which translates into more precise holes and less wear on the drill shank. This characteristic is particularly important when working with tougher materials or when drilling by hand, since a more rigid tool reduces the risk of wobble and off-centre bores. Cutting geometry optimised for clean starts and centring Equipped with a 118° tip and the classic Type N spiral, this twist drill provides predictable entry behaviour and good centring on a variety of metals. A 118° point angle reduces the initial cutting force and supports easier alignment on slightly curved or irregular surfaces. The combination of point geometry and the normal spiral pitch means the drill removes chips reliably while maintaining a controlled cutting action—an advantage for both manual drilling and machine use. Designed for workshop versatility and user convenience With a spiral length of 75 mm and an overall length of 117 mm, the short execution ensures compact handling and improved rigidity in confined setups. The MetavCUT Twist Drill is finished in black and manufactured to DIN 338 standards, making it a suitable choice for drilling alloyed and unalloyed steels, cast iron, non‑ferrous metals and many plastics. The roll-walzen HSS production process yields an elastic drill that is easier to resharpen and reduces brittle fracture risk for smaller diameters. Choose the MetavCUT Twist Drill for workshop-grade metal drilling — METAV Werkzeuge offers expert technical advice via email (info@metav-werkzeuge.com), phone (+49 2822 7131930) or WhatsApp (+49 170 2837271) to help select the right tool for the task Technical data Bezeichnung: Twist Drill Marke: MetavCUT SKU: 40081-FDA Durchmesser: 8.1 mm Spitzenwinkel: 118° Spirallänge: 75 mm Gesamtlänge: 117 mm Farbe: black Ausführung: short Typ: Type N Material: HSS Norm: DIN 338 Anwendung: Drills for metal Für Bohrmaschine: Drilling Machine Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What materials can the MetavCUT Twist Drill (Type N) be used on? The MetavCUT Twist Drill Type N is suitable for alloyed and unalloyed steel, cast iron, non‑ferrous metals and many plastics; its HSS composition makes it versatile for a broad range of metal drilling tasks. Is the MetavCUT Twist Drill suitable for use with a hand drilling machine? Yes, the MetavCUT Twist Drill in short execution is designed for compatibility with hand drilling machines and offers improved rigidity and control during manual operation. For what is a Twist Drill used? A Twist Drill such as the MetavCUT Twist Drill is primarily used for machining high‑strength materials and larger hole diameters. Its form allows for straightforward resharpening and it withstands greater loads. Which three drill types exist? The main categories are metal drills (like the MetavCUT Twist Drill), wood drills and stone/concrete drills. Why are Twist Drills sharpened at the point? The point sharpening reduces the cross‑cut at the tip of the twist drill; sharpening lowers friction forces and therefore requires less feed force while improving centring in the workpiece. Can a metal drill be used to drill wood? A metal drill such as the MetavCUT Twist Drill can be used in wood, but it typically offers poorer guidance and a less clean finish compared with dedicated wood drills; however it is easier to resharpen and shows less self‑feeding tendency. At which drilling depths is the Twist Drill most commonly used? The Twist Drill is the most used tool for solid drilling. For diameters up to 20 mm and drilling depths up to 100 mm it is commonly employed for through‑holes and general metalwork. What is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to HSS is not always correct. When choosing between the two, assess whether working conditions justify a higher investment in HSSE for your specific applications.
8.1mm HSS-E Twist Drill DIN 338 ,short, 5% cobalt-alloyed, Type N - MetavCUT
Als Fazit bietet dieser kurze Spiralbohrer eine Kombination aus HSS-E-Material, geschliffener Schaftgeometrie und einem 135° Spitzenwinkel für stabile, präzise Ergebnisse beim Bohren von Metall. Profitieren Sie von hoher Rundlaufgenauigkeit und reduziertem Bruchrisiko bei kleinen bis mittleren Bohrdurchmessern und bestellen Sie direkt über METAV Werkzeuge oder fragen Sie unsere Beratung bei Bedarf an. Spiralbohrer 8,1 mm – kurz, HSS-E (MetavCUT) Der Spiralbohrer 8,1 mm ist ein kurzer HSS-E Metallbohrer für präzise Bohrungen in legierten und unlegierten Stählen sowie Gusseisen und Nichteisenmetallen. Kurz-Ausführung für höhere Stabilität Material HSS-E mit 5% Kobaltlegierung Geschliffener Zylinderschaft für hohe Rundlaufgenauigkeit Spitzenwinkel 135° für harte Werkstoffe DIN 338: kurze Spiralbohrer mit Zylinderschaft Kompakte Bauweise sorgt für bessere Präzision und weniger Vibrationen Die Kurz-Ausführung reduziert die Auskraglänge und erhöht dadurch die Stabilität beim Bohren. Für Anwender bedeutet das weniger Ausschlag, sauberere Bohrlöcher und eine geringere Belastung des Bohrfutters. Besonders bei Arbeiten in Stahl oder Guss zeigt sich der Vorteil: die reduzierte Neigung zum Verbiegen führt zu gleichmäßigen Bohrbildern und reduziert Nacharbeiten. HSS-E und geschliffene Geometrie für saubere Schnitte und Langlebigkeit Das Material HSS-E mit 5% Kobalt bietet erhöhte Warmfestigkeit und Verschleißbeständigkeit, wodurch der Bohrer auch bei höheren Schnittgeschwindigkeiten standhält. Die geschliffene Ausführung sorgt für sehr scharfe Schneiden und exakten Rundlauf; das Ergebnis sind präzise, gratarme Bohrungen. Bei stationärer Nutzung empfiehlt sich Kühlen, da geschliffene Bohrer bei falscher Handhabung spröder reagieren können. Passende Anwendungen und empfohlene Einsatzbereiche Der Bohrer eignet sich für den typischen Werkstattalltag: Handwerk, Montage und industrielle Werkstätten profitieren von zuverlässigen Ergebnissen beim Bohren in Metall. Im Bereich 2,0 mm bis 13,0 mm ist diese Ausführung universell einsetzbar, sowohl in Handbohrmaschinen als auch in stationären Säulenbohrern. Für besonders präzise Passungen empfiehlt es sich, vorzuapern oder mit Zentrierbohrer anzupunkten. Sichere Anwendungstipps für lange Lebensdauer Für saubere Bohrbilder und geringes Werkstückwandlern sollten Drehzahl und Vorschub auf Material und Durchmesser abgestimmt werden; bei harten Werkstoffen ist der 135° Spitzenwinkel vorteilhaft. Vermeiden Sie tiefe Lochungen ohne Späneschnitt oder Kühlung, und nutzen Sie bei Bedarf mehrstufiges Aufbohren bei größeren Bohrungen. Die Packungseinheit erlaubt einfachen Austausch beim Verschleiß. Empfehlung: Für präzise Metallbohrungen die Kurz-Ausführung von MetavCUT wählen und bei Fragen unsere technische Beratung per eMail info@metav-werkzeuge.com oder telefonisch +49 2822 7131930 kontaktieren Produktmerkmale Artikelnummer: 47081-FDA Marke: MetavCUT Serie: Standard Line Bezeichnung: Spiralbohrer Daten: Durchmesser: 8,1 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Verpackungseinheit: 5 Besonderheiten Material: HSS-E (Hochleistungs-Schnellarbeitsstahl, kobaltlegiert) Schaftausführung: geschliffen (CNC-Schliff für hohe Rundlaufgenauigkeit) Norm: DIN 338 (kurze Spiralbohrer mit Zylinderschaft) Typ: Typ N (Normalspirale, geeignet für Metall) Farbe: 5% kobaltlegiert FAQ Für welche Werkstoffe ist dieser Bohrer am besten geeignet? Der MetavCUT Spiralbohrer 8,1 mm aus HSS-E mit 5% Kobalt ist ideal für legierten und unlegierten Stahl, Gusseisen sowie Nichteisenmetalle und Kunststoffe; die Kombination aus Material und 135° Spitzenwinkel erlaubt sicheres Anbohren harter Werkstoffe. Eignet sich die kurze Ausführung für Handbohrmaschinen? Ja. Die Kurz-Ausführung des Spiralbohrers ist aufgrund der reduzierten Auskraglänge besonders stabil und eignet sich für den Einsatz in Handbohrmaschinen sowie in stationären Säulenbohrern. Wodurch unterscheidet sich die geschliffene Schaftausführung? Geschliffene Bohrer bieten sehr scharfe Schneiden und hohe Rundlaufgenauigkeit, wie beim MetavCUT Spiralbohrer mit geschliffenem Zylinderschaft; das sorgt für präzise Bohrlöcher, erfordert aber angepasste Kühlung und vorsichtigen Vorschub. Brauche ich einen Zentrierbohrer vor dem Bohren mit diesem Durchmesser? Für höchste Maßhaltigkeit empfiehlt sich das Anpunkten mit einem Zentrierbohrer; für Standardanwendungen im Bereich 2,0–13,0 mm kann der Bohrer direkt verwendet werden, je nach Maschine und Materialbeschaffenheit. Was bedeutet die Norm DIN 338 für diesen Bohrer? DIN 338 klassifiziert kurze Spiralbohrer mit Zylinderschaft; beim vorliegenden MetavCUT Spiralbohrer garantiert die Norm die Ausführung als kurzer Spiralbohrer, geeignet für den stationären und mobilen Einsatz in metallbearbeitenden Anwendungen.
8.1mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Type N short, Ø 8.1 mm, 135° point angle, Bright finished, Short execution, DIN 338, HSS‑G (MetavCUT) A Twist Drill (Type N) designed for precise metal drilling on drilling machines and stationary machine tools. Short design for higher stability and precision HSS‑G fully ground for sharp, clean holes 135° point angle suited for hard materials like stainless steel Conforms to DIN 338 for short twist drills Short overall length reduces vibration and deflection Greater Stability and Faster Drilling for Metalwork The short design of this Twist Drill delivers increased Stability and reduced deflection when working with hard materials. Shorter overhang from the Chuck improves concentricity and lowers the risk of bending, which directly raises hole accuracy. In many industrial applications the HSS‑G ground geometry achieves up to 40% faster drilling and requires 50% less feed force compared with conventional HSS drills, so productivity improves while Operator fatigue decreases. Precise Tip Geometry for Tough Materials A 135° point angle optimises entry into hard and abrasion‑resistant metals by reducing the initial bite and spreading heat. For less experienced users: the point angle is the cone at the Drill Tip that influences how quickly the tool penetrates and how well it centres. With Type N normal spiral geometry this tool balances cutting speed and chip evacuation, making it particularly effective for Stainless Steel, Cast Iron and Alloyed Steels. Engineered Finish and Compliance for Reliable Results The fully ground flute and land geometry (HSS‑G) produce very sharp cutting edges and excellent Runout accuracy, yielding cleaner holes and longer life under correct conditions. The product conforms to DIN 338, which classifies short Twist Drills with cylindrical shanks and specifies manufacturing tolerances and execution variants. This standardisation supports reproducible setup and interchangeability in workshop environments. Recommended Use and Machine Compatibility Designed primarily for machining metal, this Twist Drill suits both stationary machine tools and drilling machines; it is most effective when used with appropriate cutting speeds, coolant and steady clamping. For hand‑held Drilling Machines take care with feed and torque limits because fully ground HSS drills can be more brittle than rolled variants; cooling and moderate speeds extend tool life. Typical applications include holes in unalloyed and alloyed steels, castings, sintered parts and hard plastics. Material Care and Maintenance Tips The HSS‑G material benefits from correct machining parameters: use steady coolant/lubrication for deep or high‑speed holes, and avoid excessive pecking without coolant to prevent heat build‑up. The fully ground geometry makes re‑sharpening straightforward for experienced toolmakers, while maintaining concentricity is essential to prevent premature breakage. For best performance, inspect the Twist Drill for wear and micro‑chipping before each critical operation. Strong recommendation: Choose the MetavCUT Twist Drill (Type N, HSS‑G) for demanding metal drilling tasks and contact METAV Werkzeuge for expert advice and application support — 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 ✔️ WhatsApp +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 45081-FDA Diameter: 8.1 mm Point angle: 135° Type: Type N Colour: Bright finished Execution: Short Spiral length: 75 mm Total length: 117 mm Shank execution: Fully ground Material: HSS-G Standard: DIN 338 For drilling machine: Drilling Machine Application: Drills for metal Model series: Standard Line Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill used for? The MetavCUT Twist Drill (Type N) is primarily used for drilling metal; it excels in producing precise holes in alloyed and unalloyed steels, cast components and hard plastics when used on drilling machines or stationary machine tools. Can the MetavCUT Twist Drill be used in a hand drill? The MetavCUT Twist Drill can be used in a hand drilling machine with caution; due to its short, fully ground HSS design it performs best in well‑supported setups and benefits from controlled feed, cooling and firm clamping to avoid breakage. For what is a Twist Drill used? Twist Drills are mainly applied to machining high‑strength materials and larger diameters; their form is easy to re‑grind and they withstand greater loads, making them suitable for demanding metalwork. Which three drill types exist? There are three main drill types: Metal drills, Wood drills and Stone/Concrete drills. Why are Twist Drills sharpened (pointed)? Sharpening reduces the cross‑cut at the tip, which lowers friction and the required feed force while improving the drill’s centring in the workpiece. Can you drill wood with a Twist Drill? Metal drills can be used in wood, but they offer poorer guidance and a less clean finish; however, they are easier to resharpen and have lower self‑feed tendencies. At which drilling depths is the Twist Drill most commonly used? Solid drilling is commonly executed with Twist Drills; they are most frequently the tool of choice for diameters up to 20 mm and drilling depths up to 100 mm. Is HSS or HSSE better? The general belief that HSSE is always superior to HSS is incorrect; choice should be based on the specific working conditions and whether those conditions justify the higher cost of HSSE.
8.25mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Twist Drill — Type N short, 8.25 mm, 118°, HSS, black (DIN 338) by MetavCUT The Twist Drill by MetavCUT is a short Type N metalworking drill bit designed for stable, precise boreholes in metals and suitable for use in drilling machines and hand drills. MetavCUT Twist Drill Type N for metal drilling 8.25 mm Diameter for precision holes 118° Point angle for fast centring Short execution for high stability Made from HSS per DIN 338 standard Precision and durability for metalworking applications The Twist Drill from MetavCUT combines a 8.25 mm diameter with a 118° tip geometry to deliver reliable entry and clean holes in a variety of metals. Manufactured from HSS (High Speed Steel), this short spiral drill offers a balance of hardness and elasticity, which reduces the risk of breakage when drilling smaller diameters and provides lasting edge retention under repeated loads. Compliance with DIN 338 ensures standardized dimensions and performance, so compatibility with typical chucks and machining fixtures is guaranteed. More stability and better control through a short design A short overall length and reduced protruding length increase stability and minimise wobble, which benefits precision work on tougher materials. The compact form reduces vibration and improves concentricity, making the drill ideal when accuracy matters and when working with portable Drilling Machines or bench-mounted equipment. Users benefit from easier handling, safer operation, and less tendency for the bit to deflect under sideways loads. Practical suitability and recommended uses This Type N Twist Drill is optimised for metalworking tasks: it is appropriate for alloyed and unalloyed steel, cast iron, non-ferrous metals and various plastics. The design supports both stationary Drilling Machines and suitable Hand Drills for robust workshop use. Professionals and advanced hobbyists who require dependable, repeatable results in mechanical, fabrication and maintenance contexts will find this short HSS drill a dependable choice. Material and tip geometry explained for confident selection HSS (High Speed Steel) provides elevated hot hardness and toughness compared with regular carbon steels, meaning the bit holds its edge under the heat generated by high RPM machining. The 118° Point angle favours faster centring and is typically chosen for softer to medium-hard materials; it also reduces thrust in the initial penetration. The Type N normal spiral geometry ensures efficient chip removal and general-purpose performance for metal drilling. For particularly hard alloys or specialised tasks, consider whether a different grade or coating would be advantageous. Choose the MetavCUT Twist Drill for reliable, precise metal drilling — for personalised technical advice or to confirm suitability for your exact application, contact METAV Werkzeuge: info@metav-werkzeuge.com • Tel: +49 2822 7131930 • WhatsApp: +49 170 2837271 Twist Drill Marke: MetavCUT SKU: 400825-FDA Diameter: 8.25 mm Point Angle: 118° Spiral Length: 75 mm Overall Length: 117 mm Execution: short Type: Type N Material: HSS Standard: DIN 338 Colour: black For: Drilling Machine (Hand drill) Application: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the MetavCUT Twist Drill Type N mainly used for? The MetavCUT Twist Drill Type N is primarily used for machining high-strength materials and drilling larger diameters in metalwork; its construction allows it to withstand higher loads and to be re-sharpened easily while maintaining performance. Can the MetavCUT Twist Drill be used in a hand drill? Yes, the MetavCUT Twist Drill is suitable for use in a Hand Drill as well as in stationary Drilling Machines, though the short execution particularly improves stability and results when mounted in robust chucks or machine spindles. What are Twist Drills used for? Twist Drills such as this MetavCUT Type N are mainly applied to the machining of high-strength materials and larger bore diameters; their geometry makes them easy to re-grind and capable of withstanding substantial loads during metal drilling. Which three drill types exist? Common categories include Metal drills, Wood drills, and Stone/Concrete drills, where the MetavCUT Twist Drill belongs to the metal drill group. Why are Twist Drills sharpened (pointed)? The sharpening reduces the minor cutting edge at the tip, significantly lowering friction and therefore the required feed force; this also improves initial centring of the MetavCUT Twist Drill in the workpiece. Can a metal Twist Drill be used to drill wood? A metal drill can be used in wood, but the MetavCUT Type N metal drill provides less guidance and a less clean finish than a dedicated wood bit; however, it is easier to re-sharpen and shows less self-feeding tendency.
8.25mm HSS-G Twist Drill DIN 338 ,short, bright finished, Type N - MetavCUT
Twist Drill — Short HSS‑G Twist Drill, Diameter 8.25 mm, 135° tip, Type N, Bright finished, Fully ground shank, DIN 338 The Twist Drill short HSS‑G Type N is a compact metal‑drilling tool designed for precise work in hard materials, suitable for use in a Drilling Machine. Short design for higher rigidity and precision HSS‑G material for sharp, clean metal holes 135° tip for improved entry in hard materials Fully ground shank for excellent runout accuracy Compliant with DIN 338 for short twist drills Precision and stability for demanding metalwork The short HSS‑G Twist Drill from MetavCUT combines a reduced overhang with a robust geometry to deliver reliable concentricity and minimal deflection. Its short design reduces the unsupported length outside the chuck, which translates into higher stability and better hole accuracy when machining steels and other hard materials. For workshop and industrial applications where repeatable hole quality matters, this configuration helps maintain machining tolerances and reduces scrap rates. Faster penetration with lower feed force A HSS‑G (ground high speed steel) construction and a 135° tip angle optimise the cutting action for tougher metals, shortening the initial entry phase and lowering required thrust. The ground flute geometry provides sharp cutting edges that support faster drilling — the design enables up to around 40% faster progress and reduces required feed forces compared with conventional HSS variants, making the short drill particularly effective for alloyed and unalloyed steel, cast materials and hardened plastics. Explanation: ground (G) means the flutes are CNC‑ground rather than roll‑formed, yielding sharper edges and improved runout accuracy. Designed for metal, tailored to professional use As a Type N normal spiral, this short twist drill is engineered primarily for metalworking on stationary or portable Drilling Machines. Typical applications include drilling in steel, cast steel, cast iron, sintered iron and non‑ferrous metals. The fully ground shank supports precise clamping and is advantageous in production environments where high concentricity and repeatability are required. For less experienced users: Type N indicates a general‑purpose metal drill with a standard spiral suited to a wide range of ferrous materials. Norm conformity and manufacturing details that matter Compliance with DIN 338 identifies this tool as a short twist drill with a cylindrical shank produced to standardised dimensions and tolerances. The bright finished surface and the fully ground shaft contribute to predictable seating in chucks and collets. Because ground HSS variants can be more brittle than rolled types, cooling and controlled feeds are recommended for stationary operations to maximise tool life. The short length also reduces vibration, improving surface finish and hole roundness in high‑precision tasks. Strong recommendation: MetavCUT short HSS‑G Twist Drill for professional metal drilling — for technical advice or to confirm suitability for a specific application, contact METAV Werkzeuge for competent consultation via eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930, WhatsApp: +49 170 2837271 Bezeichnung: Twist Drill Marke: MetavCUT SKU: 450825-FDA Typ: Type N Durchmesser: 8.25 mm Gesamtlänge: 117 mm Spirallänge: 75 mm Spitzenwinkel: 135° Material: HSS-G Ausführung: short Schaft Ausführung: fully ground Farbe: bright finished Norm: DIN 338 Für Bohrmaschine: Drilling Machine Modellserie: Standard Line Anwendung: Drills for metal Hersteller: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; info@metav-werkzeuge.com FAQ What is the ideal use of the Twist Drill by MetavCUT? The MetavCUT Twist Drill short HSS‑G is primarily used for machining high‑strength materials and larger drill diameters; its ground geometry makes it easy to regrind while withstanding greater loads, which suits heavy‑duty metalworking tasks. Which three drill types exist? When classifying common drills, there are Metal drills, Wood drills and Stone/Concrete drills; the MetavCUT Twist Drill belongs to the Metal drill category and is optimised for that purpose. Why are twist drills point‑sharpened? The point sharpening on a MetavCUT Twist Drill reduces the cross‑edge at the tip, which significantly lowers friction and therefore the required feed force, and it improves centring in the workpiece for more accurate starts. Can a Twist Drill for metal be used to drill wood? A MetavCUT metal Twist Drill can be used in wood, but it offers less guidance and a rougher finish than a purpose‑built wood drill; metal drills are easier to re‑sharpen and have less self‑feeding action. For which drilling depths is the Twist Drill commonly used? A through hole in solid material is typically made with a Twist Drill; for diameters up to around 20 mm and drilling depths up to about 100 mm, the short twist drill form is the most frequently used tool. Which is better, HSS or HSSE? The general belief that HSSE steels are inherently superior to HSS is not universally correct. Evaluate working conditions to determine whether HSSE justifies a higher cost; MetavCUT recommends choosing material and coating based on specific machining demands.
8.2mm HSS Twist Drill DIN 338 ,short, roll forged, black, Type N - MetavCUT
Der Spiralbohrer kurz von MetavCUT verbindet hohe Stabilität durch die kurze Ausführung mit der Schnittfestigkeit von HSS und eignet sich besonders für präzise Metallbohrungen; bei Bedarf technische Beratung über Metav-Qualitätsfilter anfordern. Spiralbohrer kurz von MetavCUT (HSS, DIN 338) Der Spiralbohrer kurz von MetavCUT ist ein HSS-Kurzbohrer nach DIN 338 für präzise Metallbohrungen mit hoher Stabilität. Kurze Ausführung für bessere Stabilität und Präzision HSS-Material reduziert Bruchrisiko bei < 6 mm Bohrungen Typ N Normalspirale für Metallarbeiten Durchmesser 8,2 mm mit 118° Spitzenwinkel Packungseinheit 5 Stück, SKU 40082-FDA Stabilität und Präzision für Metallbearbeitung Die kurze Bauform sorgt für deutlich verminderte Auskragung und damit für höhere Stabilität beim Bohren von Metall. Durch die reduzierte Biegespannung ist die Spanabfuhr effizienter und die Wahrscheinlichkeit eines Bruchs sinkt. Anwender profitieren von gleichmäßigeren Bohrbildern und einer geringeren Nacharbeit, was die Effizienz in Werkstatt und Produktion erhöht. Materialwahl und Spitzenwinkel – warum HSS und 118° Das verwendete HSS (Schnellarbeitsstahl) bietet Elastizität und eine hohe Warmfestigkeit, wodurch sich das Bruchrisiko bei kleineren Durchmessern reduziert. Der gewählte Spitzenwinkel von 118° ist optimiert für allgemeine Metall- und Nichteisenbearbeitung und erleichtert das Anbohren ohne übermäßiges Auslaufen. Diese Kombination reduziert Werkzeugwechsel und steigert die Prozesssicherheit. Einsatzgebiet, Maschine und Anwendernutzen Der Bohrer ist für den Einsatz in Handbohrmaschine und stationären Bohrvorrichtungen vorgesehen und eignet sich besonders für Werkstatt, Montage und Instandsetzung. Anwender erhalten mit diesem Kurzbohrer eine Lösung für Anwendungen in legiertem und unlegiertem Stahl, Gusseisen sowie Kunststoffen, wobei die kurze Ausführung die Bedienbarkeit mit üblichen Bohrmaschinen verbessert. Handhabung, Vorbohren und Lebensdauer Bei größeren Anforderungen empfiehlt sich das Vorbohren zur Entlastung der Querschneide; bei einem Zieldurchmesser von 8,2 mm sorgt korrektes Vorbohren und angepasste Schnittgeschwindigkeit für verlängerte Lebensdauer. Regelmäßige Kühlschmierstoffzufuhr und kontrollierte Vorschubgeschwindigkeit minimieren thermische Belastung und erhalten die Schneidkante. Empfehlung: MetavCUT empfiehlt den HSS-kurzen Spiralbohrer als zuverlässige Lösung für präzise Metallbohrungen; bei Detailfragen oder Bedarf an technischen Daten wenden Sie sich bitte an info@metav-werkzeuge.com oder Telefon +49 2822 7131930. Produktmerkmale Bezeichnung: Spiralbohrer Artikelnummer: 40082-FDA Marke: MetavCUT Ausführung: kurz Typ: Typ N Norm: DIN 338 Material: HSS Farbe: schwarz Für Bohrmaschine: Handbohrmaschine Verpackungseinheit: 5 Fakten Durchmesser: 8,2 mm Spirallänge: 75 mm Gesamtlänge: 117 mm Spitzenwinkel: 118° Besonderheiten DIN 338: kurze Spiralbohrer mit Zylinderschaft HSS: Schnellarbeitsstahl, erhöht Elastizität und Warmfestigkeit Typ N: Normalspirale, klassischer Metallbohrer Kurz: reduzierte Auskragung für mehr Stabilität Farbe: schwarz FAQ Ist der Bohrer für Edelstahl geeignet? Der MetavCUT Spiralbohrer kurz aus HSS ist für viele Stahlarten geeignet, bei sehr harten Edelstahlqualitäten kann jedoch ein spezieller 135°-Bohrer oder ein Hartmetallwerkzeug sinnvoller sein; SKU 40082-FDA eignet sich insbesondere für allgemeine Stahl- und Gussarbeiten. Kann man den Bohrer in einer Handbohrmaschine verwenden? Ja, der Spiralbohrer kurz ist für Handbohrmaschine ausgelegt und bietet durch die kurze Auskragung höhere Stabilität, wodurch präzise Bohrungen auch mit mobilen Geräten möglich sind. Welche Vorteile hat die kurze Ausführung im Vergleich zu Standardlänge? Die kurze Ausführung reduziert das Verbiegen und verbessert die Rundlaufgenauigkeit, was die Bohrqualität erhöht und die Lebensdauer des Werkzeugs verlängert. Wie groß ist die Packungseinheit und eignet sich die Packung für Werkstattbedarf? Die Verpackungseinheit beträgt 5 Stück, ideal für Werkstattbedarf und Serienarbeiten, SKU 40082-FDA ermöglicht eine schnelle Wiederauffüllung von Verschleißteilen. Was bedeutet Typ N bei diesem Bohrer? Typ N steht für Normalspirale, die klassische Spiralform für Metallbohrungen; kombiniert mit HSS bietet sie eine Balance aus Stabilität und Schnittleistung für allgemeine Anwendungen.
Reliable performance for daily drilling
The Standard line is a versatile series of HSS (high-speed steel) twist drills, also described as standard twist drills or precision HSS twist drills, engineered for everyday industrial and workshop use. Positioned between economy options and specialist pro-grade tools, the standard line delivers consistent, repeatable results for regular drilling tasks without the need for high-cost alloys.
How the standard line performs in practice
Designed as precision ground (HSS‑G) twist drills, the standard line combines a refined manufacture process with a classic geometry. A typical 118° tip and a cleanly formed point give good penetration and reliable centring, while extremely smooth flute surfaces support efficient chip evacuation. The result is stable running, improved hole quality and extended tool life under normal production and maintenance conditions.
Key advantages that matter on the shop floor
- Reduced rework thanks to high concentricity and precise hole quality
- Lower tool consumption through enhanced wear resistance from precision grinding
- Faster cycle times via efficient chip removal from smooth flutes
- Broad applicability across common materials: steel, cast iron, sintered metal, plastics and non‑ferrous metals
- Ideal balance of performance and cost for workshops, maintenance teams and assembly lines
Technical data
- Material: HSS (high-speed steel)
- Manufacture: precision ground (HSS-G)
- Tip angle: 118° (typical)
- Features: smooth flutes, optimised point geometry, excellent concentricity
- Applications: unalloyed steel, low-alloy steel, cast iron, sintered metal, plastics, non‑ferrous metals
Why Metav is the smart sourcing choice
Metav stands for democratisation of precision. As an experienced precision partner, Metav combines decades of technical know-how with a broad assortment, making high-quality measuring and workshop tools accessible to small and large operations alike. With over 48,000 customers, more than 250,000 products and a logistics hub in Emmerich, Metav offers dependable supply and a curated quality filter for the european market — the sensible route to equip your shop with standard line twist drills and complementary tooling.
FAQ
What materials are standard line twist drills suitable for?
The standard line twist drills are suitable for unalloyed and low‑alloy steel, cast iron, sintered metal, plastics and non‑ferrous metals, matching typical workshop and light industrial requirements.
How does the precision ground (HSS‑G) design benefit drilling results?
Precision ground manufacture increases concentricity and improves cutting edge finish, which leads to better hole quality, reduced vibration and longer tool life compared with roll‑formed entry‑level drills.
Are standard line drills a substitute for pro‑grade specialist drills?
Standard line drills are intended as the reliable everyday option; they deliver consistent performance for regular production and maintenance but are not a replacement when extreme loads or specialised alloys demand pro‑grade materials.
Which synonyms should procurement teams use when searching for these tools?
Search terms such as “standard twist drills”, “HSS standard drills” or “precision HSS twist drills” will reliably lead to the standard line and comparable products.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com