Durable indexable inserts for efficient metalcutting
Indexable inserts are hardened cutting elements designed to deliver consistent material removal in metalworking, providing cost-effective tool life management and repeatable results for turning, milling and drilling operations. Suited for machining steel, stainless and heat-resistant alloys, these inserts offer rapid edge renewal and reduced downtime through simple indexing, while versions optimised for internal coolant significantly improve chip control and thermal management in demanding applications. By choosing the right insert grade and geometry you gain improved tool life, predictable wear behaviour and better surface finish thanks to enhanced chip control, with key benefits including wear-resistant carbide, internal coolant compatibility and reliable chip breaking.
CCGT 04T102 SH730 Wendeplatten - Tungaloy
Reliable cutting performance from a coated carbide SH730 grade and precise 0.2 mm corner radius ensures consistent chip formation and good edge stability for turning tasks; the ISO‑compliant geometry and 80° rhombic form simplify holder selection and reduce setup time. Order the insert via Metav Werkzeuge or consult our specialists for application matching. CCGT04T102 SH730 ISO indexable insert for turning — Tungaloy, rhombic 80°, 0.2 mm The CCGT04T102 SH730 is an ISO‑compliant indexable insert for external and internal turning, optimised for small‑tool conditions and variable engagement. Coated carbide grade SH730 Rhombic insert with 80° included angle 0.2 mm corner radius for fine finishing One-sided chipbreaker for consistent chips Stable cutting performance with a tough coated substrate The SH730 grade is a coated carbide developed for tough, edge‑stable performance in turning operations, especially where small inserts or varying depths of cut are required. Because the substrate combines toughness with a wear‑resistant coating, the cutting edge remains stable under intermittent engagement and changing forces. Compatibility is defined by ISO geometry — shape, relief angle, tolerance class, fastening, size and thickness — which simplifies selection of the correct holder and reduces trial‑and‑error in production. The result is fewer tool changes and improved process reliability. Geometry that improves surface finish and reduces rework A rhombic 80° included angle together with a 0.2 mm corner radius provides a balance between strength and a fine cutting edge, helping to produce consistent surface quality with reduced burr formation. The 1.59 mm thickness stabilises the insert in the pocket while the 7° relief angle supports predictable cutting forces; these measurable geometries translate directly into higher first‑pass yield and lower finishing effort. Where finish matters, the combination of small corner radius and chip control contributes to reliable part appearance and dimensional consistency. Practical system compatibility and efficient clamping The insert is supplied with a cylindrical hole and a single‑sided countersink (40°–60°), enabling secure clamping with standard screw‑clamp systems and straightforward indexing. The one‑sided chipbreaker is designed to manage swarf and assist in predictable chip flow for typical turning tasks. The system approach — ISO indexable insert, matched external holder or boring bar, underlay/clamp set and replacement screws — allows fast tool changes and straightforward spare‑parts management, reducing downtime and simplifying inventory. This practicality supports stable production planning and makes the insert a sensible choice for repetitive or mixed‑batch turning. For reliable, edge‑stable turning operations with Tungaloy carbide inserts, contact Metav Werkzeuge for specification matching and stock information — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6837456 SKU: 6837456-Tungaloy Manufacturer SKU: TUN6837456 Model series: ISO indexable turning inserts Facts Thickness: 1.59 mm Corner radius: 0.2 mm Included angle: 80° Relief angle: 7° Plate size: 04 Countersink angle: 40°–60° Special features Coated carbide grade SH730 Rhombic shape One-sided chipbreaker Cylindrical hole with single-sided countersink Suitable for external and internal turning System build: ISO insert, compatible holder/boring bar, underlay/clamp set and spare screws FAQ How is compatibility with holders determined? Compatibility is determined by shape, relief angle, tolerance class, fastening, size and thickness; the ISO designation of the CCGT04T102 insert ensures straightforward matching to compliant holders. What turning tasks suit this insert? The insert is intended for external and internal turning and is particularly useful where small tools or variable engagement require a tough, edge‑stable grade. What does the SH730 designation indicate? SH730 denotes a coated carbide grade optimised for toughness and cutting‑edge stability during turning, giving reliable performance under changing cutting conditions. How does the one‑sided chipbreaker affect machining? The one‑sided chipbreaker promotes controlled chip segmentation and evacuation, reducing the risk of chip entanglement and improving surface consistency on typical turning operations. What is the benefit of the cylindrical hole and countersink? The cylindrical hole with a single‑sided countersink (40°–60°) allows secure, repeatable clamping with common screw‑clamp systems, aiding quick indexing and low‑vibration fixation. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 04T102 SH730 Wendeplatten - Tungaloy
Combining reliable chip control, coated carbide SH730 and ISO compatibility, this insert supports stable, productive turning across varying engagement conditions; ideal where tool life and repeatable results are priorities. Order the insert directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. CCGT04T102 SH730 – CCGT turning insert for turning (Tungaloy) The CCGT04T102 SH730 is an ISO‑standard indexable turning insert engineered for external and internal turning, offering robust edge stability for small tools and variable engagement conditions. Coated carbide grade SH730 Rhombic insert with 80° lead angle Single-sided chipbreaker Cylindrical hole with 40°–60° countersink Consistent productivity through material and grade The combination of a coated carbide substrate and the SH730 grade delivers a balance between toughness and wear resistance, suited to applications where variable depths of cut and intermittent contacts occur. The coating reduces flank wear and contributes to long tool life, while the grade’s toughness helps maintain edge integrity under changing loads. For production environments seeking predictable component quality and extended tool cycles, this insert is designed to reduce downtime and maintain cycle stability via proven cutting‑edge performance. Geometry and clamping that support precision and access The rhombic geometry with an 80° lead angle and 7° clearance provides a robust cutting edge while allowing good axial access in confined turning operations. The 0.2 mm nose radius supports fine surface finishes and precise profile work, whereas the 1.59 mm plate thickness contributes to secure clamping and vibration resistance when used with appropriate holders. These features together ensure repeatable dimensional control and help to prevent premature edge chipping, especially in assemblies where holder form, tolerance class and fastening method determine compatibility. Application range and system considerations Designed as part of an ISO turning‑plate system, the insert fits compatible external holders or boring bars and requires the correct underplate/clamp set and screw for full performance. The single‑sided chipbreaker improves chip control in many steel and alloy turning tasks; the cylindrical hole with single‑side countersink (40°–60°) supports stable seating and reliable torque transfer. Material‑specific selection of chipbreaker and cutting data remains essential: Metav Werkzeuge can advise on optimal feeds, speeds and holder pairings to match component material and machining stability. For application advice, availability and ordering of Tungaloy SH730 inserts contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored guidance and procurement support Technical Data Article number: 6862180 Manufacturer SKU: TUN6862180 Our SKU: 6862180-Tungaloy Model series: ISO turning inserts Designation: CCGT04T102 SH730 Manufacturer: Tungaloy Key figures Insert size: 04 Thickness: 1.59 mm Nose radius: 0.2 mm Lead angle: 80° Clearance angle: 7° Hole style: cylindrical hole + single‑side countersink (40°–60°) Design & Special features Material: coated carbide Grade: SH730 Shape: rhombic Chipbreaker: single‑sided Application: turning (external and internal) ISO‑standardised designation FAQ What materials is this insert suitable for? The CCGT04T102 SH730 insert is a coated carbide grade developed for a broad material range; it is particularly effective where edge toughness is required and is commonly used on steels and alloyed materials. How does the 80° lead angle affect performance? The 80° lead angle increases cutting edge engagement and strength, offering improved robustness for heavier cuts and better tool life, while still allowing access for many external and internal turning tasks. Is the insert compatible with standard ISO holders? Compatibility depends on holder form, clearance angle, tolerance class, attachment and size; the insert follows ISO plate standards and fits holders designed for the CCGT04 size and mounting style. What role does the single‑sided chipbreaker perform? The single‑sided chipbreaker supports consistent chip formation and evacuation in typical turning operations, reducing the risk of entanglement and aiding surface quality under recommended cutting parameters. Which SKU should be referenced when ordering? Reference the manufacturer article number 6862180 or the manufacturer SKU TUN6862180 when ordering to ensure the correct CCGT04T102 SH730 Tungaloy insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T102 TH10 Wendeplatten - Tungaloy
Benefit from the combination of a sharp, uncoated carbide TH10 grade and ISO rhombic geometry for reduced cutting forces and reliably clean surfaces; the 0.2 mm corner radius and secure cylindrical hole with single‑side countersink support repeatable clamping and consistent part finish. Order the insert via Metav Werkzeuge or contact our consultants for application-specific recommendations. CCGT 04T102 TH10 ISO rhombic turning insert by Tungaloy — uncoated carbide, 0.2 mm radius The CCGT04T102 TH10 is an ISO rhombic turning indexable insert engineered for external and internal turning, especially where low cutting forces and a clean surface are required for non-ferrous and similar materials. ISO rhombic shape, 80° cutting geometry Uncoated carbide TH10 for low cutting forces 0.2 mm corner radius for fine surface finish Reliable cutting with low forces for non‑ferrous turning The insert’s core advantage is the TH10 uncoated carbide composition, which provides a sharp cutting edge that lowers cutting forces and reduces the tendency for built‑up edge when machining aluminium, brass and comparable materials. The ISO rhombic geometry with an 80° cutting angle and 7° relief angle balances edge strength and accessibility, enabling stable turning even at moderate overhangs. Choosing an uncoated grade supports effortless chip formation and a clean surface without relying on coating chemistry, which is especially useful in operations prioritising low heat input and easy reconditioning. Predictable surface quality and repeatability A 0.2 mm corner radius delivers a precise compromise between edge strength and surface finish: enough radius to avoid premature wear in interrupted cuts, yet small enough to produce fine profiles and dimensional accuracy. The one‑sided chipbreaker and the pin‑style clamping with cylindrical hole plus single‑side countersink (40°–60°) ensure reproducible seating and consistent chip control when paired with a suitable holder. For suppliers seeking predictable part quality, this insert narrows process variability and reduces scrap rates through stable engagement with the workpiece. System compatibility and practical handling advice As an ISO standard part, compatibility with toolholders depends on form, relief angle, tolerance class, fastening method, size and thickness; this insert’s size 04 and 1.59 mm plate thickness make it suitable for many compact external and internal holders. The system build typically comprises the insert, a matched external holder or boring bar, a backing pad/locating set and the correct clamp and screw. Select the chipbreaker and grade in line with workpiece material and machining stability to gain optimal economy and tool life rather than relying on maximum cutting parameters alone. For machining enquiries or to request application guidance for the Tungaloy CCGT04T102 TH10 insert, contact Metav Werkzeuge for expert advice and rapid supply from stock Technical data Article number: 6862125 Manufacturer SKU: TUN6862125 Seller SKU: 6862125-Tungaloy Model series: ISO turning indexable inserts Material: carbide Facts Corner radius: 0.2 mm Relief angle: 7° Cutting geometry: 80° Plate thickness: 1.59 mm Plate size: 04 Special features Grade: TH10 (uncoated) Shape: rhombic Hole: cylindrical hole with single‑side countersink (40°–60°) Chipbreaker: one‑sided Application: turning (external and internal) System components: insert, holder/boring bar, backing pad, clamp and screw FAQ What materials is this insert best suited for? The Tungaloy CCGT04T102 TH10 insert is optimised for non‑ferrous materials such as aluminium and messings, and for applications where an uncoated, sharp edge delivers low cutting forces and clean surfaces. How does the 0.2 mm corner radius affect finish and tool life? A 0.2 mm corner radius on the CCGT04T102 balances surface finish and edge durability: it helps achieve fine surface quality while providing sufficient edge strength for typical turning tasks. Is the insert compatible with standard ISO turning holders? Yes—compatibility is determined by form, relief angle, tolerance class, fastening, size and thickness; the ISO designation of this insert supports use in appropriately rated ISO holders when clamped with the correct backing pad and screw. What is the advantage of an uncoated carbide grade such as TH10? The TH10 uncoated grade promotes lower cutting forces and reduced built‑up edge during the turning of non‑ferrous materials, simplifying chip control and often improving surface quality without the need for a coating. Which chipbreaker should be chosen for stable machining? The insert features a one‑sided chipbreaker; select a chipbreaker and grade combination that matches the workpiece material and the rigidity of the setup to ensure stable chip formation and process security. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 04T102 TH10 Wendeplatten - Tungaloy
Take advantage of a sharp, uncoated carbide cutting edge and precise rhombic geometry to improve surface finish and lower cutting forces in turning operations; order the insert or request holder compatibility advice from Metav Werkzeuge for a reliable production setup. CCGT 04T102 TH10 – Indexable Turning Insert for Turning (Tungaloy) A CCGT 04T102 TH10 indexable turning insert engineered for external and internal turning, offering a sharp uncoated cutting edge suited to non‑ferrous materials and applications requiring low cutting forces. CCGT 04T102 TH10 uncoated carbide insert Rhombic shape with 80° included angle 0.2 mm corner radius for fine finishing Single-sided chipbreaker, with locating hole Consistent cutting performance for non‑ferrous machining The uncoated carbide grade TH10 is a sharp, universal grade optimised for non‑ferrous materials and operations where a clean surface and reduced cutting force are priorities. An uncoated carbide edge produces lower friction at the cutting zone compared with some coated grades, which can translate into improved surface quality and reduced power draw on light machines. For shops processing aluminium, brass or similar alloys, the combination of this grade and the insert’s geometry reduces built‑up edge and supports stable chip flow, helping to maintain part tolerances and minimise secondary finishing. The insert designation is CCGT04T102 TH10, reflecting the ISO format and the cutting grade for straightforward identification. Precise geometry and ISO compatibility for predictable results The rhombic plate form with an 80° included angle and a 7° clearance angle produces a versatile cutting geometry that balances strength and accessibility in external and internal turning. The 0.2 mm corner radius helps achieve finer surface finishes while limiting cutting forces during light cuts; larger radii would favour heavier cuts but here the smaller radius supports precision finishing tasks. Plate thickness of 1.59 mm and the standard ISO format ensure predictable seating in compatible holders, while the cylindrical hole with a single‑side countersink (40°–60°) secures repeatable clamping. Where holder compatibility is critical, match form, clearance angle, tolerance class and fixing method to ensure the insert seats correctly and maintains rigidity. System benefits: chip control, handling and process reliability A single-sided chipbreaker tailored to this insert promotes effective chip control in the most common turning modes for non‑ferrous alloys, reducing the risk of entanglement and improving cycle times. As part of a complete turning system — insert, outer holder or boring bar, shim/clamp set and replacement screws — the insert supports efficient tool changes and predictable tool life. The design contributes to reduced vibration and consistent surface quality, making it a practical choice for batch production and precision components alike. For selection of the optimal holder and clamping parts, Metav Werkzeuge can advise on the best system configuration to maximise productivity and repeatability. For specific advice on holder compatibility, recommended cutting parameters and immediate availability of the Tungaloy CCGT04T102 TH10 insert, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — consultants will support the selection of the ideal setup for the application. Technical data Article number: 6862124 Manufacturer SKU: TUN6862124 SKU: 6862124-Tungaloy Designation: CCGT04T102 TH10 Tungaloy insert Model series: ISO turning indexable inserts Material: Carbide Grade: TH10 Coating: uncoated Facts Insert size: 04 Plate thickness: 1.59 mm Clearance angle: 7° Included angle: 80° Corner radius: 0.2 mm Special features Rhombic plate form Single-sided chipbreaker With hole: cylindrical hole + single countersink (40°–60°) Compatible with ISO holders for external and internal turning Typical system: insert, outer holder or boring bar, shim/clamp set, replacement screws FAQ What materials is this insert suitable for? The CCGT04T102 TH10 indexable turning insert (Tungaloy) is optimised for non‑ferrous materials such as aluminium and brass, where a sharp uncoated edge and low cutting forces support clean surfaces. Is the insert coated or uncoated? This insert is supplied as an uncoated carbide grade TH10; the uncoated edge is chosen to reduce cutting forces and prevent built‑up edge in softer alloys. How is the insert secured in a holder? The insert has a cylindrical locating hole with a single‑side countersink (40°–60°) and seats in standard ISO‑format holders; ensure the holder matches form, clearance and thickness for correct clamping of the CCGT04T102 TH10. What finish can be expected with the 0.2 mm radius? A 0.2 mm corner radius helps achieve finer surface finishes during finishing passes; the small radius reduces tool pressure and supports dimensional accuracy on turned parts. Can this insert be used for both external and internal turning? Yes — the rhombic geometry and ISO compatibility make the insert suitable for both external and internal turning when paired with the appropriate outer holder or boring bar. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 IC908 Indexable Insert - ISCAR
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! 📧 eMail: info@metav-werkzeuge.com ✔️ WhatsApp: +49 170 2837271 ☎️ Phone: +49 2822 7131930 Performance features CCGT 04T104 insert from ISCAR Brand: ISCAR Manufacturer Order Number: CCGT04T104-F1PIC908 Series: SMALL TURN ISO-Code: CCGT04T104 Grade: IC908 Material: cemented carbide Form: rhombic Clearance Angle: 7° with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Radius: 0.4 Chip Breaker: single-sided Angle: 80° Manufacturer: ISCAR Ltd.; Industrial Zone, P.O.Box 11; 24959 Tefen; Israel; www.iscar.so.il; info@iscar.co.il Registered brand names and trademarks are the property of their respective owners. The mention of brands and registered trademarks is for descriptive purposes only. There is no connection whatsoever between our company and the brands mentioned. This is a brand new original product of the leading brand ISCAR. 40START indexable-inserts-CCGT-04T104-IC908-ISCAR 40END
CCGT 04T104 SH7025 Wendeplatten - Tungaloy
Take advantage of the SH7025 coated carbide grade and the 0.4 mm corner radius for consistent edge stability and fine surface finishes; order the CCGT04T104 insert directly via Metav Werkzeuge or request guidance from the technical consultants. CCGT 04T104 SH7025 ISO turning insert, coated carbide, 0.4 mm radius — Tungaloy CCGT04T104 SH7025 is an ISO‑standard rhombic turning insert designed for external and internal turning applications where stable cutting edges and consistent chip control are required ISO rhombic insert CCGT 04T104 SH7025 coated carbide for stable cutting 0.4 mm corner radius for fine finishing Cylindrical hole with 40°–60° countersink Reliable cutting performance for varying engagement conditions The SH7025 grade is a coated carbide developed for resilient, edge‑stable performance in turning operations, particularly suitable for smaller tools or fluctuating engagement depths. The coating enhances wear resistance while the substrate maintains toughness, which reduces flank wear and extends tool life. This combination delivers a predictable tool behaviour under interrupted cuts and variable feed rates, translating into fewer insert changes and improved production continuity. The benefit is measurable: less downtime and more consistent component quality due to stable cutting-edge performance. Precise ISO fit and simple integration into tool systems The insert follows the ISO‑standard designation and a rhombic geometry, ensuring compatibility with a wide range of holders when the form, clearance angle, tolerance class, fastening and thickness match the toolholder. Key dimensional details — 7° clearance, 1.59 mm thickness and the 80° included angle — support correct seating and repeatable clamping. The cylindrical hole with a single‑side countersink (40°–60°) secures the insert and aligns it reliably on the shim; this reduces micro‑movement and supports repeatable indexability. Clear specification of these parameters simplifies holder selection and minimises set‑up time on the shop floor. Geometry and chip control tuned for finish and productivity The 0.4 mm corner radius balances strength and surface quality: it increases edge durability compared with smaller radii while allowing a fine surface finish compared with larger radii. The single‑sided chipbreaker is optimised for turning, supporting controlled chip formation and evacuation under typical feeds and speeds. Together with the insert’s rhombic shape and single‑sided chipbreaker, this geometry reduces the risk of built‑up edge and promotes stable surface integrity. Regular maintenance of the clamping set and matching the chipbreaker to the workpiece material ensure the best combination of finish and tool life. For application recommendations or to secure delivery of the Tungaloy CCGT04T104 SH7025 insert, contact Metav Werkzeuge for tailored technical advice and order processing at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 6967397 SKU: 6967397-Tungaloy Manufacturer SKU: TUN6967397 Series: ISO turning indexable inserts Application: Turning Material: Coated carbide (SH7025) Facts Size: 04 Thickness: 1.59 mm Corner radius: 0.4 mm Clearance angle: 7° Included angle: 80° Special features Rhombic plate form Cylindrical hole with single‑side countersink (40°–60°) Single‑sided chipbreaker ISO designation: CCGT04T104 Grade/coating: SH7025 FAQ What operations is this insert intended for? The insert is intended for external and internal turning operations; the design supports common turning tasks where a small corner radius and stable edge are required. How does the SH7025 grade affect performance? The SH7025 coating and substrate combination provides enhanced edge stability and wear resistance, improving tool life and maintaining consistent cutting behaviour under variable engagement. Which holder features must match for correct installation? Holder compatibility is determined by insert form, clearance angle, tolerance class, fastening method, size and thickness; the specified 7° clearance and 1.59 mm thickness are key reference values for correct seating. What is the benefit of the 0.4 mm corner radius? A 0.4 mm corner radius offers a compromise between strength and surface quality — it improves edge robustness while still permitting fine surface finishes on turned components. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH7025 Wendeplatten - Tungaloy
Benefit from the combination of coated carbide (SH7025) for durable cutting edges, a 0.4 mm corner radius for precise profiles and ISO compatibility for straightforward toolholder matching. Order the insert directly via Metav Werkzeuge or consult our specialists for process-specific recommendations. CCGT04T104 SH7025 — ISO turning insert, rhombic 80° (Tungaloy) CCGT04T104 SH7025 is an ISO rhombic indexable insert designed for external and internal turning, offering a balance of edge stability and adaptability for variable engagement conditions. Coated carbide grade SH7025 Rhombic insert, 80° cutting angle One-sided chipbreaker for reliable chips Cylindrical hole with single-side countersink Stable cutting performance for variable conditions The coated carbide grade SH7025 is formulated to keep a stable cutting edge under changing engagement and small-tool applications. This results in consistent dimensional control and reduced rework. As an indexable insert, the geometry and coating work together to lower flank wear and support longer tool life, which contributes to predictable tool-change intervals and improved productivity. The 0.4 mm corner radius helps generate defined profiles while limiting stress concentration at the cutting edge. Clear guidance on compatibility and secure clamping Compatibility with the toolholder is governed by form, clearance angle (7°), tolerance class, clamping system, size and thickness. The insert’s ISO designation and rhombic geometry enable straightforward selection of matching holders or boring bars; the cylindrical hole with a single-side countersink (40°–60°) supports positive locating and reliable clamp engagement. Specifying the insert by its ISO code avoids uncertainty in procurement and ensures the correct seating and repeatability for high-volume turning processes. Application scope and material considerations Engineered for turning, this insert performs well where engagement conditions change or where smaller tool sizes are required. The combination of one-sided chipbreaker and the coated substrate makes it suitable for finishing to medium machining operations when the chip control and edge security are priorities. Selection of the chipbreaker and the cutter grade should follow the workpiece material and process stability to achieve the best surface finish and tool life; the insert’s design facilitates that optimisation without complex setup changes. For application advice, batch availability or to request technical data sheets for the Tungaloy SH7025 inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6967431 Manufacturer SKU: TUN6967431 SKU: 6967431-Tungaloy Model series: ISO indexable turning inserts Material: carbide ISO designation: CCGT04T104 Core specifications Corner radius: 0.4 mm Thickness: 1.59 mm Cutting angle: 80° Clearance angle: 7° Size: 04 Special features Coated carbide grade SH7025 Rhombic plate form One-sided chipbreaker Cylindrical hole with single-side countersink (40°–60°) ISO-standard indexable insert Suited to small-tool and variable engagement turning FAQ What machining operations are suitable for this insert? The insert is intended for turning operations; the CCGT04T104 SH7025 excels in external and internal turning where edge stability and chip control are important. How does the SH7025 grade affect tool life? The SH7025 coating improves edge resistance under varying cutting conditions, which helps to extend tool life and maintain consistent surface quality. Can this insert be used with standard ISO holders? Yes. The insert’s ISO designation and hole-and-clamp geometry are designed for compatibility with matching ISO toolholders and boring bars when the holder matches form, clearance and thickness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH7025 Wendeplatten - Tungaloy
Take advantage of the combination of a SH7025 coated carbide grade, an 80° rhombic geometry and a compact 0.4 mm corner radius for stable, repeatable turning cycles; order the insert directly via Metav Werkzeuge or consult the technical team for matching holders and clamping sets. CCGT 04T104 SH7025 Tungaloy indexable insert for turning CCGT 04T104 SH7025 is an ISO‑format indexable insert designed for general turning tasks, offering a robust cutting edge and compatibility with standard clamping systems SH7025 coated carbide grade for stable edges Rhombic CCGT shape, 80° cutting angle 0.4 mm corner radius for precise turning Cylindrical hole with 40°–60° countersink Consistent performance where conditions vary The SH7025 grade is a coated carbide developed to provide a tough, edge-stable cutting performance, particularly suited to smaller toolholders and varying entry conditions. As an ISO turning insert from the CCGT family, this item contributes to reduced tool-change frequency and predictable component tolerances through a combination of material resistance and a controlled coating system. The result is a more efficient machining process with fewer interruptions and consistent surface quality for both external and internal turning applications. Geometry designed for predictable chip control and secure clamping The rhombic 80° cutting angle and 0.4 mm corner radius deliver a balance between strength and detail in contour turning, while the 7° clearance aids smooth cutting action and reduces rubbing on the flank. The insert's 1.59 mm thickness and ISO size 04 ensure dimensional compatibility with standard CCGT holders; the cylindrical hole with a one-sided countersink (40°–60°) gives a reliable datum for clamping and repeatable seating. The single-sided chipbreaker supports controlled chip formation when paired with an appropriate workpiece‑matched breaker, improving cycle stability and reducing secondary finishing. Integration into machining systems and practical benefits Compatibility is determined by form, clearance angle, tolerance class, fastening, size and thickness; the insert forms part of a system that includes a matching external holder or boring bar, a shim or clamping set and spare screws. Specifying the ISO designation and the grade helps streamline procurement and inventory management, while the insert’s design promotes longer effective tool life and fewer interruptions for tool maintenance. For process planning, selecting a chipbreaker and grade adapted to the workpiece material and cutting conditions yields the best combination of productivity and surface finish. For additional guidance on holder selection or machining parameters, Metav Werkzeuge can supply tailored recommendations and technical documentation. Contact Metav Werkzeuge to confirm holder compatibility and availability — call +49 2822 7131930 or email info@metav-werkzeuge.com for expert advice and order support Technical data Manufacturer article number: 6967432 Manufacturer SKU: TUN6967432 Metav SKU: 6967432-Tungaloy Facts Corner radius: 0.4 mm Thickness: 1.59 mm Cutting angle: 80° Clearance angle: 7° Size: 04 (ISO) ISO designation: 04T104 Special features Material: Coated carbide (SH7025) Shape: Rhombic Hole: With cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: Single-sided Application: Turning Model series: ISO turning indexable inserts FAQ What turning operations is this insert suitable for? The insert is intended for both external and internal turning; the CCGT 04T104 SH7025 Tungaloy indexable insert is optimised for variable engagement and smaller tool setups. What is the corner radius and how does it affect results? The corner radius is 0.4 mm; this radius balances edge strength with the ability to produce fine contours and consistent surface finish when using the right cutting parameters. How is the insert secured in the holder? The insert has a cylindrical hole with a one-sided countersink (40°–60°); the CCGT 04T104 fit requires a compatible holder, a suitable shim or clamping set and the correct fastening screws for repeatable seating. Which material and grade are used for the cutting edge? The cutting material is coated carbide, grade SH7025, chosen for its toughness and edge stability under changing cutting conditions. How to ensure optimal chip control with this insert? Pair the insert with a chipbreaker and cutting data matched to the workpiece material; the single-sided chipbreaker supports controlled chips when process parameters are correctly set. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH725 Wendeplatten - Tungaloy
Benefit from the combination of the SH725 coated cemented carbide grade, precise 80° rhombic geometry and a 0.4 mm corner radius for stable cutting edges and reliable surface quality. The insert is compatible with ISO toolholders when matched by form, relief angle, tolerance and thickness — order directly via Metav Werkzeuge or consult our technical advisers for application-specific recommendations. CCGT 04T104 SH725 indexable turning insert for external and internal turning, Tungaloy A CCGT04T104 SH725 indexable insert designed for versatile turning operations, offering a rhombic form and chip control tailored to variable engagement conditions. SH725 coated cemented carbide grade Rhombic 80° geometry for versatile turning 0.4 mm corner radius for fine surface finishes Cylindrical hole with 40°–60° countersink High-process stability from the cutting grade The SH725 coated cemented carbide is formulated for stable cutting edges and consistent performance across a broad range of turning tasks. Its composition is suited to operations where small tools or varying engagement conditions demand a tough, edge-retaining grade. The coating reduces flank wear and extends usable life, which translates directly into fewer indexings and reduced downtime. For production environments seeking predictable tool life and repeatable results, this grade supports higher machine utilisation and consistent component quality. Geometry and finish: designed for controlled surfaces The rhombic plate form with an 80° lead angle delivers a balance between strength and accessibility to the cutting zone, making it appropriate for both external and internal turning. The 0.4 mm corner radius is ideal where fine surface finish and dimensional consistency are required; it reduces the risk of chatter compared with sharper radii while still allowing close tolerance work. The plate thickness of 1.59 mm contributes to insert rigidity; together these geometric parameters support improved surface quality and reduce the need for secondary finishing. Mounting, hole design and compatibility with ISO toolholders The insert features a cylindrical hole with a single-side countersink (40°–60°) to ensure secure clamping and correct seating in compatible toolholders. Compatibility with a given holder depends on matching form, relief (frewinkel) of 7°, tolerance class, fixing method, size and thickness. As an ISO-standard turning insert, it integrates into standard tool systems when those parameters align. Users should verify holder geometry and clamping hardware to ensure optimal seating and to avoid misalignment that can compromise tool life. Application guidance and chip control Equipped with a single-sided chipbreaker, this insert facilitates predictable chip formation in many standard turning tasks. Select the chipbreaker and grade in accordance with workpiece material, depth of cut and machine stability: the combination of the SH725 grade and the chip control geometry is particularly effective when engagement conditions vary or when small tooling is used. For unfamiliar materials or complex cycle requirements, request cutting-parameter recommendations to balance productivity and tool life; Metav Werkzeuge can provide tailored guidance based on machining centre capability and component tolerances. For application-specific cutting data or availability of the Tungaloy SH725 insert, contact Metav Werkzeuge for immediate technical support and procurement assistance. Technical data Article number: 6737261 Manufacturer SKU: TUN6737261 SKU: 6737261-Tungaloy Article name: CCGT04T104 SH725 Tungaloy indexable insert Facts Corner radius: 0.4 mm Plate thickness: 1.59 mm Insert size: 04 Lead angle: 80° Relief angle: 7° Design & features Rhombic plate shape Single-sided chipbreaker Cylindrical hole with single-side countersink (40°–60°) Coated cemented carbide grade SH725 ISO-standard turning insert Intended for external and internal turning Compatibility determined by form, free angle, tolerance, fixing, size and thickness FAQ What materials is this insert suitable for? The CCGT04T104 SH725 insert is designed as a versatile, tough coated carbide grade suitable across a wide material spectrum; choose the chipbreaker and parameters to match the specific steel, alloy or softer materials in the process. How does the 0.4 mm corner radius affect surface finish? A 0.4 mm radius provides a compromise between strength and finish: it improves surface quality and reduces vibration risk compared with very small radii, while allowing precise dimensional control in finishing passes. Is the insert compatible with standard ISO turning holders? Yes — as an ISO-standard turning insert, compatibility requires matching the holder by form, relief angle (7°), tolerance class, fixing method, size and thickness; verify the holder seat and clamping to ensure correct fit. What is the benefit of the cylindrical hole with countersink? The cylindrical hole combined with a single-side countersink (40°–60°) secures correct seating and repeatable clamping, which improves tool stability and reduces the likelihood of insert displacement under load. Can this insert be used for both external and internal turning? Yes; the rhombic 80° geometry supports both external and internal turning applications when paired with the appropriate holder and cutting conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH725 Wendeplatten - Tungaloy
Reliable turning performance is achieved through the combination of the tough SH725 coating, precise 0.4 mm nose radius and ISO rhombic geometry for stable chip control. Order the CCGT04T104 SH725 insert directly via Metav Werkzeuge or ask the consultants for selection support. CCGT04T104 SH725 indexable insert for turning (rhombic 80°) by Tungaloy CCGT04T104 SH725 is an ISO‑format indexable insert engineered for general turning applications, offering stable cutting behaviour for smaller tools and variable engagement conditions. Coated cemented carbide grade SH725 Rhombic 80° geometry with 0.4 mm nose radius Cylindrical hole with one-sided countersink Consistent chip control for productive turning The rhombic 80° geometry combined with the single-sided chipbreaker delivers repeatable chip formation and reduced vibration in external and internal turning. The coated cemented carbide SH725 grade is formulated for toughness and edge stability, which helps maintain process reliability when engagement conditions change or when smaller toolholders are used. The 0.4 mm nose radius balances dimensional accuracy with enough edge strength for a wide range of finishing and light roughing tasks, improving productivity and surface quality. Clear compatibility rules reduce setup time Compatibility with toolholders is determined by insert form, 7° clearance angle, tolerance class, clamping method, size and thickness. This ISO plate fits holders specified for CCGT‑style inserts and uses the supplied centre hole for secure fastening. The cylindrical hole with a one‑sided countersink (40°–60°) ensures reliable seating and repeatable positioning, simplifying index changes and reducing setup variability on the machine. Grade and chipbreaker guidance for material selection The SH725 coating and substrate combination is optimised for toughness and wear resistance, making it suitable where edge stability is critical. Select a matching chipbreaker and grade depending on workpiece material and cutting parameters: a more pronounced chipformer benefits ductile materials, while a smoother edge and smaller nose radius aid finishing of harder alloys. This philosophy allows cost‑effective operation by aligning insert characteristics with the component material and cutting strategy. Practical benefits in daily workshop use Using ISO‑formatted indexable inserts streamlines inventory and reduces downtime: the standardised geometry permits straightforward replacement and interchange across compatible holders. The thin 1.59 mm plate thickness and compact 04 size support applications where tool clearance is limited. Together, the geometry, hole design and SH725 performance contribute to longer productive periods between index changes and predictable results in both simple and variable turning operations. For reliable productivity with Tungaloy's SH725 grade, contact Metav Werkzeuge for availability and technical advice via info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will assist with selection and compatibility details Technical data Article number: 6737271 Manufacturer SKU: TUN6737271 Seller SKU: 6737271-Tungaloy Facts Nose radius: 0.4 mm Included angle: 80° Clearance angle: 7° Plate thickness: 1.59 mm Plate size: 04 Special features Grade: SH725, coated cemented carbide Shape: rhombic (CCGT) Hole: cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: single-sided Application: turning Model series: ISO indexable turning inserts Compatibility: determined by form, clearance, tolerance, clamping, size, thickness FAQ What holder types are compatible with this insert? Compatibility depends on the holder accepting CCGT‑format ISO inserts with the same form, 7° clearance angle, size 04 and thickness 1.59 mm; the centre hole and countersink ensure correct seating for matched holders. Which materials suit the SH725 grade best? The SH725 coated cemented carbide is designed for toughness and edge stability, making it suitable for a broad range of steels and mixed machining conditions where stable chip formation is required. What is the purpose of the cylindrical hole and countersink? The central hole with a one‑sided countersink (40°–60°) secures the insert reliably in the seat, improving repeatability and simplifying index changes during turning operations. Is the 0.4 mm nose radius suitable for finishing? A 0.4 mm nose radius provides a balance between strength and surface finish; it is suitable for many finishing and light roughing tasks, offering controlled tool deflection and surface quality. How does the single‑sided chipbreaker affect performance? The single‑sided chipbreaker promotes consistent chip control for the specified cutting conditions, improving process stability and reducing the risk of built‑up edge on the cutting face. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH725 Wendeplatten - Tungaloy
Take advantage of the combination of a wear-resistant SH725 grade, ISO compatibility and a compact 0.4 mm edge radius for steady production results; order the insert directly via Metav Werkzeuge or ask the consultants for application guidance. CCGT04T104 SH725 indexable insert for turning — Tungaloy A CCGT04T104 SH725 indexable insert designed for ISO-standard external and internal turning applications, offering a tough coated-carbide grade for variable engagement and small-tool setups ISO rhombic insert CCGT 04T104 format SH725 coated carbide for tough cuts 0.4 mm corner radius for consistent edge Countersunk central hole, single-sided chipbreaker Consistent performance from a tough coated grade The insert is manufactured in the SH725 grade, a coated carbide engineered for a balance of toughness and edge stability. This composition reduces flank and crater wear under varying cut conditions, which translates into longer periods between indexings and fewer unscheduled tool changes. For workshops running short, repeatable cycles or jobs with fluctuating engagement, the hardened coating and substrate combination supports reliable machining and maintains dimensional control during both light and interrupted cuts. ISO conformity and simplified tooling decisions Built to the ISO designation, the insert’s compatibility is defined by its shape, relief angle, tolerance class, mounting style, size and thickness, enabling straightforward matching with external holders, boring bars and clamping kits. The ISO standardisation reduces selection errors, eases inventory management and ensures interchangeability across machines. Included in the system concept are the matching external holder or boring bar, the support shim/clamping set and replacement screws, which together provide a reproducible clamping interface and consistent tool geometry. Edge geometry and chip control for repeatable results The rhombic plate with an 80° included angle, 0.4 mm corner radius and 7° relief angle concentrates strength at the cutting edge while the single-sided chipbreaker promotes predictable chip formation. The insert’s centre hole with a cylindrical bore and a one-sided countersink (40°–60°) secures positive seating and concentricity in the clamp, supporting stable cutting forces and improved surface finish. With a plate thickness of 1.59 mm, the insert is particularly suited to small-tool arrangements where stiffness and controlled engagement are essential for part accuracy. Practical benefits for production workflows Selecting this insert yields measurable advantages: enhanced tool life through the SH725 grade and coated surface, consistent part quality via ISO interchangeability, and reduced set-up variability thanks to the standardised hole and seating geometry. For operations that require both external and internal turning, the combination of edge geometry and chipbreaker minimises rework and supports faster throughput, making it a pragmatic choice for jobbing shops and production lines seeking stability across a range of steels and alloy conditions. For application advice or to order original Tungaloy CCGT04T104 SH725 indexable inserts, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6737260 SKU: 6737260-Tungaloy Manufacturer SKU: TUN6737260 Model series: ISO-Drehwendeschneidplatten Name: CCGT04T104 SH725 Tungaloy indexable insert Core specifications Corner radius: 0.4 mm Relief angle: 7° Included angle: 80° Thickness: 1.59 mm Size: 04 Features and materials Grade/coating: SH725 (coated carbide) Material: cemented carbide Shape: rhombic Chipbreaker: single-sided Hole style: cylindrical hole + one-sided countersink (40°–60°) Typical application: turning (external and internal) System components: ISO insert compatible with matching holder, shim/clamping set and replacement screws FAQ What holders are compatible with this insert? Compatibility depends on the ISO shape and size; the CCGT04T104 SH725 indexable insert seats in ISO rhombic CCGT holders with matching size, relief and clamping geometry. Which materials can be machined with this grade? The SH725 coated carbide is formulated for general turning across a wide material range, offering good edge stability for varying steels and mixed cutting conditions. What does the 0.4 mm corner radius mean for surface finish? A 0.4 mm corner radius provides a balance between edge strength and surface finish, helping to produce consistent finishes while resisting premature edge chipping on interrupted cuts. Is the insert suitable for both external and internal turning? Yes, the plate form and hole/clamping arrangement are intended for use in both external holders and compatible boring bars for internal turning. How does the chipbreaker affect machining? The single-sided chipbreaker promotes predictable chip formation and evacuation, which supports stable cutting and reduces the risk of built-up edge under variable feed conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH730 Wendeplatten - Tungaloy
Benefit from the combination of SH730 coated carbide, a 0.4 mm corner radius and ISO-compliant geometry for stable cutting and consistent tool life; order directly via Metav Werkzeuge or consult our specialists for application advice. CCGT 04T104 SH730 Tungaloy indexable insert for turning — rhombic, 0.4 mm radius A CCGT04T104 SH730 indexable insert engineered for ISO-standard external and internal turning to deliver stable cutting performance in variable engagement conditions ISO rhombic insert CCGT 04T104 SH730 coated carbide grade 0.4 mm corner radius for precision 7° clearance angle, with centre hole Stable cutting and longer edge life thanks to SH730 coating The SH730 coating on a coated carbide substrate provides a reliable balance between toughness and wear resistance, making this indexable insert especially suitable for turning tasks with changing engagement and interrupted cuts. The combination of coating technology and substrate hardness reduces flank wear and helps maintain a consistent cutting edge, which translates into fewer index changes and higher productivity on the shopfloor. For operations requiring repeatable surface quality, the enhanced edge stability supports predictable tool-change intervals and reduced downtime. ISO compatibility and secure clamping for predictable process performance Designed as an ISO-series turning insert, the rhombic geometry (size 04) and precise tolerances ensure compatibility with standard holders when form, clearance angle, tolerance class, attachment method, size and thickness match. The 7° clearance angle and the centre hole with cylindrical bore plus single-sided countersink (40°–60°) enable secure fastening and correct seating in holders or boring bars, reducing the risk of seating errors. The 1.59 mm plate thickness and defined wedge angle contribute to controlled vibration behaviour and make the insert suitable for both external and internal turning setups. Practical advantages for production — chip control and small-tool performance Equipped with a one-sided chipbreaker, this insert promotes consistent chip formation and evacuation in a wide range of steels and non-ferrous materials. The 0.4 mm corner radius supports fine finishing passes and contributes to dimensional stability on turned profiles. The grade selection aims at applications with smaller tooling or where engagement conditions vary, so the insert is a practical choice for mixed-production environments seeking efficient tool use and straightforward inventory management. Documented compatibility with ISO holders simplifies tool planning and reduces trial-and-error during process setup. Choose the SH730-coated Tungaloy insert for robust, repeatable turning results and contact Metav Werkzeuge for availability and detailed application support via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6862142 Manufacturer SKU: TUN6862142 SKU: 6862142-Tungaloy Manufacturer: Tungaloy Dimensions & ratings Size: 04 Thickness: 1.59 mm Corner radius: 0.4 mm Clearance angle: 7° Wedge angle: 80° Design & features Shape: rhombic Coating / grade: SH730 Material: coated carbide Chipbreaker: one-sided Hole: cylindrical with single-sided countersink 40°–60° Application: turning (external & internal) ISO designation: CCGT04T104 FAQ What materials is this insert suitable for? The CCGT04T104 SH730 Tungaloy indexable insert is intended for a broad range of turning tasks; the SH730 grade is optimised for toughness and stable cutting, making it suitable for many steels and mixed-material production. How does the 0.4 mm corner radius affect the turned surface? A 0.4 mm corner radius on the CCGT04T104 insert helps produce consistent surface finish and improved dimensional stability on finishing passes while reducing the risk of edge chipping in interrupted cuts. Is the insert compatible with standard ISO holders? Yes — the insert follows ISO specifications for form and dimensions; compatibility depends on matching holder form, clearance angle, tolerance class, attachment and thickness. What is the benefit of the centre hole and countersink design? The centre hole with a cylindrical bore and single-sided countersink (40°–60°) ensures secure clamping in holders and promotes correct seating, which enhances process reliability when using the CCGT04T104 SH730 Tungaloy insert. Can this grade be used for tools with small overhangs or variable engagement? The SH730 grade is designed for toughness and cutting-edge stability, which makes it well suited to smaller tooling arrangements and applications with changing engagement conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH730 Wendeplatten - Tungaloy
Take advantage of the combination of SH730 coated carbide, ISO-compliant CCGT geometry and a fine 0.4 mm corner radius for consistent turning results and stable edge behaviour; order the inserts via Metav Werkzeuge or consult the specialists for application matching. CCGT 04T104 SH730 – Tungaloy indexable turning insert CCGT04T104 SH730 indexable turning insert for general turning applications, designed for stable cutting edges and reliable performance in small tools or variable engagement conditions ISO CCGT profile, 80° rhombic geometry SH730 coated carbide for stable cutting edges 0.4 mm corner radius for fine contouring Cylindrical hole with single-sided countersink Consistent cutting performance where engagement varies The SH730 grade is a coated carbide developed for toughness and edge stability, which makes it particularly suitable for turning operations where entry conditions change or where tool size is reduced. The composition and coating balance wear resistance with toughness to maintain a predictable cutting edge under interrupted cuts or varying depths of cut. For production environments that require repeatable component tolerances, this behaviour reduces rework and contributes to steady cycle times. The ISO format supports straightforward replacement and indexing, helping to keep machine downtime to a minimum while maintaining consistent surface quality. Geometry and small-radius control for precise finishes The rhombic 80° profile combined with a 0.4 mm corner radius and a 7° relief angle gives predictable contact conditions at the insert tip, enabling controlled chip formation and improved surface integrity on turned parts. The modest radius supports fine contouring and radius-sensitive features while the rhombic shape offers good access in both external and internal turning. Because compatibility with the cutterholder depends on form, relief angle, tolerance class, attachment and plate thickness, the standardised ISO design simplifies selection of matching holders and clamping hardware for reliable clamping and repeatability. Practical system benefits for faster tool changes The plate is supplied with a cylindrical hole and a single-sided countersink (40°–60°), ensuring secure seating and quick indexing in compatible holders. The single-sided chipbreaker supports controlled chip evacuation in many turning tasks and contributes to consistent cutting forces, which is especially helpful in automated or high-throughput machining. With a plate thickness of 1.59 mm and ISO sizing that aligns with common holders, the insert integrates easily into existing tool systems; a complete setup typically comprises the insert, a suitable external holder or boring bar, a shim/packing set and replacement screws for maintenance-ready operation. Contact Metav Werkzeuge for application advice and stock availability of Tungaloy SH730 indexable turning inserts — the team will recommend the correct holder and grade for the intended turning task Technical data Article number: 6837457 Manufacturer SKU: TUN6837457 Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Designation: CCGT04T104 SH730 Tungaloy-Wendeplatte Facts Plate size: 04 Plate thickness: 1.59 mm Corner radius: 0.4 mm Relief angle: 7° Nominal angle: 80° Special features Coating/grade: SH730 (coated carbide) Plate shape: rhombic Hole: with cylindrical hole and single-sided countersink (40°–60°) Chipbreaker: one-sided Application: Drehen (external and internal turning) ISO-compliant CCGT geometry FAQ What cutting tasks is this insert best suited for? The CCGT04T104 SH730 indexable turning insert is intended for external and internal turning where edge stability and toughness are required, especially when using smaller tools or when engagement conditions vary. How does the SH730 grade affect tool life and reliability? SH730 is a coated carbide grade designed for stable cutting edges and good wear resistance; the grade delivers reliable performance for interrupted cuts and changing engagement, prolonging usable life of the insert under these conditions. Which holder features are critical for correct assembly? Correct assembly requires a holder matching the ISO CCGT form, the relief angle and the plate thickness; the cylindrical hole with countersink must align with the holder screw and seating to ensure repeatable clamping. Is the corner radius suitable for fine contouring? Yes, the 0.4 mm corner radius enables finer contouring and controlled transition radii, helping to achieve improved surface finishes on turned features. What is the SKU and article number for ordering reference? Ordering reference: article number 6837457, manufacturer SKU TUN6837457 for the CCGT04T104 SH730 Tungaloy indexable turning insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 SH730 Wendeplatten - Tungaloy
Available for efficient turning operations, the insert combines a coated carbide grade engineered for edge stability with ISO interchangeability and compact dimensions for small-tool applications; order the CCGT04T104 SH730 insert through Metav Werkzeuge or request consultation for optimised holder selection. CCGT04T104 SH730 — ISO turning indexable insert by Tungaloy for precision turning CCGT04T104 SH730 is an ISO‑format indexable insert designed for turning applications where stable cutting edges and reliable chip control are required CCGT04T104 format, ISO-compliant SH730 coated carbide for edge stability Rhomboid 04 size, 0.4 mm nose radius Cylindrical hole with single-sided countersink Consistent cutting performance for short‑run and variable engagement turning The SH730 grade is a coated carbide developed for toughness and edge stability, particularly advantageous when tool engagement varies or when using smaller toolholders. As an ISO indexable insert, it provides predictable wear behaviour and repeatable geometry, which reduces setup variability and scrap rates. The 0.4 mm nose radius supports both finishing and light roughing; this balance helps maintain surface quality while allowing economical cutting parameters. Clear guidance on holder compatibility and mounting Compatibility with a holder is determined by the insert’s form, clearance, tolerance class, fastening method, size and thickness. The rhomboid geometry and the presence of a cylindrical hole with single-sided countersink (40°–60°) enable secure clamping in many standard external and internal turning toolholders. Selecting a holder that matches the ISO form and the insert thickness ensures correct seating and repeatable cutting geometry, reducing vibration and improving tool life. Practical benefits: chip control, process security and economy The single‑sided chipbreaker is optimised for consistent chip formation under varied conditions; this improves evacuation and reduces the risk of built-up edge. Together with the coated carbide composition, the insert contributes to longer in‑service life and fewer tool changes, supporting higher productivity and lower running costs. For operations where minimised downtime and predictable tool life matter, this insert delivers measurable process security. Choosing the right insert settings and application tips For general turning, start with conservative cutting speeds and increase while monitoring surface finish and tool wear; the insert’s edge stability allows progressive optimisation. Match the chipbreaker and cutting data to workpiece material and rigidity of the setup. Where inserts are used for internal turning, confirm holder clearance and coolant access. If uncertainty exists regarding parameters or holder selection, specialist advice will streamline implementation and safeguard results. Contact Metav Werkzeuge for application advice on the Tungaloy SH730 insert and assistance in selecting the correct holder and cutting data — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Manufacturer article number: 6862153 SKU: TUN6862153 Series: ISO turning indexable inserts Type designation: CCGT04T104 Grade: SH730 Core data Nose radius: 0.4 mm Plate thickness: 1.59 mm Included angle: 80° Clearance angle: 7° Size: 04 Features Material: coated carbide Plate shape: rhomboid Hole: with cylindrical hole + single-sided countersink (40°–60°) Chipbreaker: one-sided Application: turning (external and internal) ISO series compatibility FAQ What turning operations suit this insert? The CCGT04T104 SH730 indexable insert is designed for both external and internal turning; it performs well where variable engagement and small-tool setups challenge edge stability. How is holder compatibility ensured? Compatibility depends on form, clearance, tolerance class, fastening method, size and thickness; the CCGT04T104 dimensioning follows the ISO series so matching holders with the same ISO form and thickness ensures correct seating. Which cutting geometry is provided by the insert? This rhomboid insert offers an 80° included angle and 0.4 mm nose radius, suitable for mixed finishing and light roughing tasks while maintaining surface quality. Does the SH730 grade require special cutting data? The SH730 coated carbide grade favours toughness and edge stability; start with conservative speeds and feeds, then optimise based on observed wear and surface finish for reliable results. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 TH10 Wendeplatten - Tungaloy
Combining the TH10 uncoated carbide grade with an ISO‑specified rhombic geometry and a 0.4 mm corner radius ensures low cutting forces and consistently clean surfaces in turning operations; order genuine Tungaloy inserts directly via Metav Werkzeuge or consult the technical team for application advice CCGT CCGT04T104 TH10 turning insert (ISO rhombic, 80°) — Tungaloy A CCGT04T104 TH10 turning insert designed for external and internal turning, offering a low‑force uncoated cutting edge suited to non‑ferrous materials and precision finishing ISO‑standard rhombic insert, 80° cutting angle Uncoated carbide TH10 for low cutting forces 0.4 mm corner radius for consistent finish Cylindrical hole with 40°–60° countersink Lower energy input and cleaner surface finish for turning The combination of the TH10 grade and an uncoated carbide edge is engineered to minimise cutting forces, which directly reduces spindle load and heat generation during machining. For applications in non‑ferrous materials and softer alloys, this results in a cleaner surface finish and less burr formation. The rhombic ISO geometry with an 80° main cutting angle delivers a dependable compromise between strength and accessibility, helping to maintain cycle times while protecting the cutting edge. Stable clamping and repeatable seat for secure operations Compatibility with toolholders is determined by the insert’s form, clearance angle and tolerance class; the cylindrical hole with 40°–60° countersink and a thickness of 1.59 mm provide a reliable mechanical seat that reduces micro‑movement and improves repeatability. Because clamping accuracy influences tool life and dimensional stability, the insert’s ISO conformity ensures predictable behaviour when paired with standard outside holders and boring bars, lowering the risk of setup variance and rework. Controlled chip flow and predictable cutting behaviour The single‑sided chipbreaker design works in concert with the uncoated cutting edge to shape chips for safer evacuation and consistent tool contact. A 0.4 mm corner radius supports edge strength while producing consistent surface waviness suitable for finishing passes. For operations where low cutting forces and good surface integrity are priorities, the geometry helps to avoid chatter and minimise feed‑induced marks, delivering dependable results with fewer interventions. Versatility in turning tasks and practical selection guidance Designed for both external and internal turning, the insert performs best where a sharp, uncoated edge is advantageous—such as aluminium, copper alloys and mixed non‑ferrous batches. Selection should consider workpiece stability and required finishes: match the single‑sided chipbreaker and TH10 grade to the material and machining conditions for optimised productivity. For less rigid setups or heavy interrupted cuts, choose a more robust geometry or a different grade; for fine finishing, the low cutting forces of this insert reduce the tendency to rub and deposit built‑up edge. Contact Metav Werkzeuge for availability and application advice on Tungaloy TH10 turning inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility with specific holders and materials Technical data Article number: 6862164 Manufacturer SKU: TUN6862164 SKU: 6862164-Tungaloy Model series: ISO‑Drehwendeschneidplatten Material: Hartmetall Application: Drehen Key dimensions Cutting angle: 80° Clearance (relief) angle: 7° Plate thickness: 1.59 mm Plate size: 04 Corner radius: 0.4 mm Special features ISO rhombic plate (CCGT04T104) Grade: TH10 (uncoated carbide) Hole: with cylindrical hole and one‑sided countersink (40°–60°) Chipbreaker: single‑sided Plate form: rhombic FAQ Which holders are compatible with this insert? The CCGT04T104 TH10 insert fits holders designed for ISO rhombic CCGT plates; compatibility depends on form, relief angle, tolerance class, fastening method, size and thickness, so verify the holder matches the ISO geometry. For which materials is the TH10 grade recommended? The TH10 uncoated carbide grade is aimed at non‑ferrous materials and applications where a sharp, uncoated edge supports low cutting forces and a clean surface finish. How does the 0.4 mm corner radius influence surface quality? A 0.4 mm corner radius increases edge strength while maintaining a fine surface profile, helping to reduce feed marks and produce a consistent finish on turning passes. What advantage does the cylindrical hole with countersink provide? The cylindrical hole plus 40°–60° countersink ensures secure clamping and accurate seating in compatible toolholders, improving repeatability and reducing the risk of insert movement during machining. Is this insert suitable for interrupted cuts or heavy machining? The CCGT04T104 TH10 insert is optimised for low cutting forces and finishing in non‑ferrous materials; for heavy interrupted cuts or highly unstable setups, a more robust geometry or different grade is recommended. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 04T104 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of a sharp TH10 uncoated carbide grade, rhombic CCGT geometry with 80° cutting angle, and precise ISO compatibility for consistently low cutting forces and clean surfaces; order the insert directly via Metav Werkzeuge or consult the team for selection and fast supply. CCGT 04T104 TH10 indexable turning insert (ISO 04T104) by Tungaloy for turning A CCGT04T104 TH10 indexable insert designed for accurate external and internal turning, offering a sharp uncoated carbide cutting edge optimised for non-ferrous materials and low cutting forces. Sharp universal uncoated carbide TH10 Rhombic CCGT geometry, 80° cutting angle Single-sided chipbreaker for controlled chips Cylindrical hole with one-sided countersink Higher productivity with lower cutting forces The uncoated TH10 grade provides a sharp, universal carbide edge that reduces cutting resistance and supports a cleaner surface finish when machining non-ferrous materials. This results in lower power consumption and less heat generation, which in turn extends tool life and stabilises process parameters. Selecting a grade that emphasises low cutting forces helps maintain consistent part tolerances and reduces the need for rework, making the insert an efficient choice for high-throughput turning operations. Fast, reliable set‑up through ISO conformity Compatibility is ensured by the ISO designation and standardised geometry: the rhombic CCGT form with an 80° cutting angle and 7° clearance simplifies selection of a matching holder and clamping system. The insert thickness of 1.59 mm and the 0.4 mm corner radius support precise seating and repeatable indexing in approved toolholders. Because fit is determined by form, relief angle, tolerance class, clamping type, size and thickness, the standardised design reduces set‑up time and minimises the risk of incorrect assembly, enabling faster changeovers on the shop floor. Controlled chip formation and application guidance The single-sided chipbreaker is engineered for predictable chip control in turning operations, particularly when working with aluminium alloys, brass and other non-ferrous materials where chip evacuation is critical. The insert features a cylindrical hole with a one-sided countersink (40°–60°), permitting secure clamping with standard screws and underlay plates. In practice, pairing the insert with an appropriate external holder, shim and clamp set ensures stability and consistent results for both external and internal turning tasks. Practical benefits in machining systems As part of an indexable system, the insert slots into a holder and is secured with a screw and shim assembly, allowing rapid replacement and minimised downtime. The uncoated carbide composition provides good edge sharpness for finishing and light roughing, while the ISO format ensures interchangeability across compatible toolholders. For applications requiring different chip control or tougher materials, selecting an alternative chipbreaker or grade within the same ISO family permits straightforward adaptation without changing the holder. For technical matching, supply options and immediate availability of the TH10 grade, contact Metav Werkzeuge for personalised advice and fast delivery; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6862181 Manufacturer SKU: TUN6862181 Seller SKU: 6862181-Tungaloy Model series: ISO-Drehwendeschneidplatten Facts Corner radius: 0.4 mm Plate thickness: 1.59 mm Cutting angle: 80° Clearance angle: 7° Plate size: 04 Special features Material: carbide (uncoated) Grade/sort: TH10 (sharp universal) Plate shape: rhombic (CCGT) Hole: cylindrical hole with one-sided countersink (40°–60°) Chipbreaker: single-sided Typical use: external and internal turning System components: insert, holder, shim/clamp set and replacement screws FAQ What materials is this insert best suited for? The TH10 grade is intended primarily for non‑ferrous materials; the CCGT04T104 insert delivers low cutting forces and clean surface finish when machining aluminium alloys, brass and similar materials. How does the ISO designation affect holder choice? ISO conformity of the CCGT 04T104 designation ensures compatibility with holders that match the form, relief angle, tolerance class, clamping type, size and thickness specified for the insert. Is the insert coated or uncoated? This insert is supplied as an uncoated carbide grade (TH10), offering a sharp edge for low cutting resistance and good finishing performance. What is the corner radius and why does it matter? The corner radius is 0.4 mm; this influences surface finish and cutting forces—smaller radii help produce finer finishes at reduced cutting loads. Can this insert be used for internal turning? Yes, the insert is suitable for both external and internal turning when mounted in an appropriate internal turning holder and with correct clamping. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060200 J740 Wendeplatten - Tungaloy
Benefit from an ISO-standard, rhombic 06 geometry combined with the J740 Tungaloy carbide grade for stable cutting and extended edge life; compatibility with common holders simplifies integration into existing tool systems. Order the insert directly via Metav Werkzeuge or ask our consultants for application guidance. CCGT060200 J740 ISO turning insert — rhombic 06, 7° clearance by Tungaloy The CCGT060200 J740 Tungaloy indexable insert is an ISO‑standard rhombic turning plate designed for external and internal turning, delivering a balanced mix of wear resistance, toughness and edge stability for general turning applications. CCGT060200 J740 indexable insert by Tungaloy ISO rhombic 06 geometry, 80° included angle 7° clearance angle for secure cutting Cylindrical hole with 40°–60° countersink Single-sided chipbreaker, 2.38 mm thickness Improved process stability through material and grade The combination of the J740 Tungaloy grade and a carbide substrate delivers a reliable balance between wear resistance and toughness, which is essential for consistent cutting performance in turning. The chosen grade supports stable cutting edges that reduce unexpected tool changes and promote predictable tool life, meaning fewer interruptions to machining cycles and more stable component quality. The ISO-standard geometry further aids repeatable results across toolholders that conform to the same specification. Practical advantages in everyday turning With a 7° clearance angle and a compact 2.38 mm thickness, the insert is optimised for typical external and internal turning tasks where secure clamping and defined edge geometry are crucial. The integrated single-sided chipbreaker helps control chip formation for a wide range of workpiece materials used in general turning. This combination reduces the risk of built-up edge and improves surface finish on turned parts while keeping the machining process efficient and economical. System compatibility and simple replacement The insert conforms to the usual ISO plate system and fits standard external holders or boring bars when matched for form, clearance, tolerance class, fastening type, size and thickness. The cylindrical hole with a single‑side countersink (40°–60°) ensures reliable seating and clamping, while the rhombic profile (06) gives flexibility for different turning geometries. As a component within an ISO‑based system, the plate is easy to replace and maintain with common underplate/clamp sets and spare screws, simplifying inventory and tool management. Contact Metav Werkzeuge for tailored application advice on Tungaloy turning inserts or to discuss suitable clamping and holder combinations — eMail: info@metav-werkzeuge.com | Phone: +49 2822 7131930 Technical data Article number: 6801257 SKU: 6801257-Tungaloy Manufacturer: Tungaloy Manufacturer SKU: TUN6801257 Facts ISO code: 060200 Size: 06 Thickness: 2.38 mm Clearance angle: 7° Included angle: 80° Special features Rhombic plate form With hole; cylindrical hole + one‑side countersink (40°–60°) Single‑sided chipbreaker Carbide material Grade: J740 (Tungaloy) Model series: ISO turning indexable inserts Application: Turning FAQ How does the J740 grade perform on medium‑hard steels? The J740 grade in this indexable insert provides a balanced combination of wear resistance and toughness, making the CCGT060200 J740 suitable for reliable turning of medium‑hard steels with consistent edge stability. Is the insert compatible with standard ISO toolholders? Yes, the ISO designation 060200 and the rhombic 06 form ensure compatibility with holders and boring bars designed for ISO turning plates, provided form, clearance, tolerance class, fastening and thickness match. What is the benefit of the cylindrical hole with countersink? The cylindrical hole plus one‑side countersink (40°–60°) allows secure seating and improved clamping stability, reducing movement under cutting forces and supporting repeatable positioning during tool changes. Can this insert be used for both internal and external turning? The geometry and chip control of this insert make it suitable for both external and internal turning operations when paired with the appropriate external holder or boring bar. Which SKU should be referenced when ordering replacements? Use SKU 6801257‑Tungaloy or the manufacturer SKU TUN6801257 to ensure the correct CCGT060200 J740 insert is supplied. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060200 J740 Wendeplatten - Tungaloy
Take advantage of the combination of robust Tungaloy carbide grade, ISO‑standard geometry and precise mounting features for consistent turning results; order directly via Metav Werkzeuge or consult our specialists for holder compatibility and optimal chipbreaker selection. CCGT 060200 J740 turning insert (ISO 060200) by Tungaloy The CCGT060200 J740 is a rhombic turning insert intended for external and internal turning, offering a 7° clearance and a one‑sided chipbreaker for stable material removal. ISO‑standard rhombic insert size 06 Tungaloy J740 carbide grade 7° clearance angle for versatile turning Cylindrical hole with 40°–60° countersink Productivity through stable wear resistance and repeatability The design of this indexable tool emphasises economic machining cycles by combining a wear‑resistant cemented carbide substrate with a grade tuned for turning operations. The J740 grade balances hardness and toughness to extend edge life under varying cutting conditions; this translates into fewer interruptions for insert changes and more predictable process planning. When used in a suitable holder, the geometry and material pairing minimise flank wear and maintain dimensional consistency across production batches, supporting leaner setups and improved uptime. Reliable chip control and geometry benefits for turning A focused geometry reduces thermal and mechanical loading at the cutting edge: the rhombic shape with an included angle of 80° and the one‑sided chipbreaker direct chips reliably away from the cutting zone. The 7° clearance angle helps prevent rubbing while preserving form at the workpiece, making the insert suitable for both finishing and moderate roughing passes depending on stability. Explaining the chipbreaker: it moderates chip thickness and curl to avoid entanglement and promote evacuation, which is particularly useful on long, slender parts or interrupted cuts where chip control is critical. Compatibility, mounting and selecting the right holder Compatibility with clamping systems depends on form, clearance angle, tolerance class, fixation and thickness; the insert’s cylindrical hole with a single‑sided countersink (40°–60°) provides a standard method for secure fastening. When specifying a holder, match the plate size (06), thickness 2.38 mm, and the ISO pocket geometry to achieve correct seat and clamp engagement. Using the proper combination prevents micro‑movement at the interface, safeguarding edge life and ensuring repeatable positioning during tool indexation. Suitable materials and practical application notes The grade is designed for general turning tasks; select the chipbreaker and cutting data to match the workpiece material and stiffness of the setup. The insert’s balance of toughness and hardness makes it appropriate for a broad range of materials encountered in general turning operations; adjustments in feed and depth of cut help tailor performance to specific steels, alloyed materials or cast components. For internal turning, ensure sufficient rigidity in the bar and holder assembly to fully exploit the insert’s cutting potential. Why choose a Tungaloy grade for production reliability Tungaloy’s material development focuses on achieving a stable cutting edge under industrial conditions. The J740 grade complements the insert geometry to deliver steady performance in repetitive machining tasks, reducing scrap risk and enabling predictable tool change cycles. In process chains where repeatability and tool life are priorities, this combination supports consistent surface quality and dimensional control over longer runs. Contact Metav Werkzeuge today to specify the CCGT 060200 J740 insert and confirm holder compatibility, clamp style and optimal chipbreaker selection for the intended turning application. Technical data Article number: 6801254 Manufacturer SKU: TUN6801254 SKU: 6801254‑Tungaloy Model series: ISO‑Drehwendeschneidplatten Material: Hartmetall Facts ISO code: 060200 Insert size: 06 Thickness: 2.38 mm Clearance angle: 7° Included angle: 80° Hole: with hole Hole style: cylindrical hole + single‑side countersink 40°–60° Special features Rhombic plate form One‑sided chipbreaker Designed for external and internal turning Tungaloy grade J740 ISO‑standard geometry for holder compatibility FAQ What pocket and clamp features are required for this insert? The CCGT060200 J740 insert needs a pocket matching ISO 060200 geometry with secure clamping that accommodates a cylindrical locating hole and the single‑side countersink to ensure stable seating. Which applications suit the J740 grade best? The J740 grade on this indexable insert is intended for general turning operations where a balance of wear resistance and toughness is required, supporting both finishing and moderate roughing passes. Can this insert be used for internal turning? Yes, the insert’s geometry and chip control make it suitable for internal turning provided the bar and holder offer adequate rigidity for the chosen cutting parameters. How does the one‑sided chipbreaker affect performance? The one‑sided chipbreaker moderates chip flow and thickness to improve evacuation and reduce the risk of chip re‑cutting, which benefits surface finish and tool life in many turning scenarios. Is the insert compatible with holders from different manufacturers? Compatibility is determined by form, clearance angle, tolerance class, fixation, size and thickness; using holders that conform to ISO standards for the 06 size and 060200 designation ensures interchangeability with the CCGT060200 J740. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 060200 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of an uncoated cermet finishing grade, a sharp cutting edge for low cutting forces, and ISO compatibility to ensure smoother finishing cycles and consistent surface quality; order directly via Metav Werkzeuge or consult our advisors for application guidance. CCGT060200 NS9530 Tungaloy indexable insert — ISO rhombic finishing grade for turning, 7° clearance The CCGT060200 NS9530 indexable insert is an ISO rhombic turning insert designed for finishing operations in steel, offering a sharp edge and low cutting forces for high-quality surfaces. CCGT 060200 finishing grade NS9530 Uncoated cermet for high surface finish 7° clearance for stable cutting Rhombic ISO insert with centre hole Achieve superior surface finish with the NS9530 grade The uncoated cermet grade NS9530 is formulated as a finishing material with a sharp cutting edge that reduces cutting forces and improves surface quality in continuous turning passes. In practice, this means fewer secondary operations and faster attainment of target roughness when machining steel. The microstructure of the grade is optimised for light to moderate feeds and small depths of cut, so the machining process is stabilised and vibration is minimised. For users unfamiliar with cermet, the term denotes a ceramic–metal composite that combines wear resistance with toughness, delivering consistent finishes where conventional carbides may leave more pronounced tool marks. Simple integration with existing ISO holders for reliable set-up Compatibility is ensured by the ISO designation and the insert geometry: the rhombic form, tolerance class, fixing arrangement and plate thickness determine correct mounting. The insert features a 2.38 mm plate thickness, a centre hole with a cylindrical bore plus a one-sided countersink (40°–60°) and a 7° clearance angle, all of which are standardised to match ISO toolholders and boring bars. Because the insert is ISO‑coded, selection of a matching clamping kit or seat is straightforward and the mechanical fit is verifiable by form and size rather than trial and error. This reduces set-up time and supports reproducible clamping forces, which in turn helps to preserve the cutting edge and maintain process stability. Reduce machining effort while securing consistent results A single-sided chipbreaker and the finishing geometry are intended for continuous cuts and small radial engagements, so cycle time can be optimised without sacrificing surface quality. The substrate and edge preparation are designed to keep cutting forces low, which benefits machines and fixturing by reducing dynamic loads during operation. For shops aiming to improve first-pass quality, this insert lowers the need for manual finishing and supports predictable tool life across batches. In assembly, the system build typically comprises the ISO insert, an appropriate external holder or boring bar, a locating pad and clamping set plus replacement screws, enabling a complete and repeatable tooling solution. For precision finishing in steel select the Tungaloy NS9530 CCGT060200 insert — contact Metav Werkzeuge for tailored application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6997899 SKU: 6997899-Tungaloy Manufacturer SKU: TUN6997899 Model series: ISO indexable turning inserts Material: cemented carbide Core specifications ISO designation: 060200 Insert designation: CCGT060200 Grade: NS9530 Plate size: 06 Plate thickness: 2.38 mm Clearance angle: 7° Main angle: 80° Hole: with centre hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: single-sided Application: Turning Features & applications Uncoated cermet finishing grade Sharp cutting edge for low cutting forces Suited to continuous cuts and small depths of cut Compatible with ISO rhombic holders and boring bars System setup: indexable insert, matching external holder/boring bar, locating pad/clamping set, replacement screws Typical use: external and internal turning FAQ What materials is this insert intended for? The CCGT060200 NS9530 Tungaloy indexable insert is a finishing grade designed primarily for steel; the uncoated cermet substrate is optimised to deliver a high surface finish in continuous turning. How does the NS9530 grade affect cutting forces and surface finish? NS9530 is an uncoated cermet grade that offers a sharp cutting edge and reduced cutting forces, which helps achieve improved surface quality and less need for secondary finishing when using the CCGT060200 insert. Is the insert compatible with standard ISO holders? Yes. The insert carries the ISO designation 060200 and the rhombic form, clearance angle (7°) and thickness (2.38 mm) are standardised to match ISO toolholders and boring bars. What is the purpose of the centre hole and countersink on this insert? The centre hole with a cylindrical bore and a one-sided countersink (40°–60°) provides secure clamping and correct seating in the toolholder, ensuring repeatable positioning and stable cutting conditions for the CCGT060200 insert. Which cutting conditions suit this chipbreaker and geometry best? The single-sided chipbreaker and finishing geometry are intended for continuous cuts at small depths of cut and light to moderate feeds, where consistent surface finish and low cutting forces are prioritised. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060200 SH7025 Wendeplatten - Tungaloy
Benefit from the combination of stable edge life, reliable chip control and ISO compatibility for efficient turning operations; order the insert directly via Metav Werkzeuge or request specialist consultation for toolholder matching. CCGT 060200 SH7025 – indexable turning insert for turning, Tungaloy A CCGT 060200 SH7025 indexable insert engineered for ISO-standard turning applications, offering secure clamping with a cylindrical hole and a single-sided countersink for consistent seating. Coated carbide grade SH7025 for edge stability Rhombic 06 geometry with 80° included angle 7° clearance angle optimised for general turning Cylindrical hole with single-sided countersink (40°–60°) Consistent machining through a purpose-built cutting grade The CCGT geometry delivers repeatable results in both roughing and finishing passes. The combination of a coated carbide substrate and the SH7025 grade yields a balance of toughness and wear resistance, which supports longer tool life under variable engagement conditions. As an indexable insert conforming to ISO standards, it simplifies inventory and reduces setup time when matched to the correct holder, enabling a more predictable production flow and reduced downtime. Secure seating and proven geometry for reliable cuts The rhombic 06 form with an 80° included angle provides a robust cutting edge for external and internal turning, distributing cutting forces effectively. A 7° clearance angle lowers rubbing and reduces heat generation at the flank, improving surface integrity. These geometric factors, combined with standardised tolerances, support straightforward replacement and consistent part quality across batches. Durable edge control for variable conditions Coating technology and substrate selection focus on chip control and edge stability; the single-sided chipbreaker suits interrupted cuts and fluctuating feed conditions commonly encountered in workshop environments. The grade is particularly suited to smaller tooling assemblies and operations where engagement depth varies, delivering confidence in repeatability while maintaining productivity. The insert’s construction from coated carbide and its tailored microgeometry reflect Tungaloy’s design priorities for robust machining performance. System compatibility that reduces setup risk Compatibility depends on form, relief angle, tolerance class, fastening method, size and thickness; the insert’s cylindrical hole with single-sided countersink ensures a positive, concentric clamp when used with matched chucks or holders. Integration into a complete system—insert, external holder or boring bar, and clamping set—minimises vibration and secures positional stability. The result is a cost-effective approach to turning that maintains surface finish and dimensional accuracy across repeated cycles. For tool matching, availability or to order the CCGT 060200 SH7025 insert from Tungaloy, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to arrange technical advice and supply. Technical data Article number: 6967437 SKU: 6967437-Tungaloy Manufacturer SKU: TUN6967437 Model series: ISO turning indexable inserts Material: Coated carbide Core specifications Size designation: 06 ISO designation: 060200 Plate thickness: 2.38 mm Included angle: 80° Clearance (relief) angle: 7° Hole: with cylindrical hole and single-sided countersink (40°–60°) Design & special features Rhombic plate form Single-sided chipbreaker Suitable for external and internal turning Grade SH7025: tough, edge-stable coating for variable engagements FAQ What applications suit this insert best? The insert is intended for turning operations, including both external and internal turning; its geometry and grade support mixed operations in workshops and production runs. Which materials can be machined with this grade? The SH7025-coated carbide grade is formulated for a broad material spectrum where toughness and edge stability are required, especially in conditions with varying engagement and smaller tooling setups. How is the insert secured in the holder? The insert features a cylindrical hole with a single-sided countersink (40°–60°) to ensure positive clamping when used with compatible holders and clamping sets. Is the insert ISO compatible for easy replacement? Yes, the insert follows ISO plate designation 060200 and is designed for straightforward replacement and interchangeability within ISO-compliant tool systems. What benefits does the rhombic 06 geometry provide? The rhombic 06 form with an 80° included angle offers robust cutting edges for varied turning cuts, improving force distribution and stability during machining. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060200 SH7025 Wendeplatten - Tungaloy
Take advantage of a robust, edge-stable grade and a proven ISO shape for consistent turning performance; the coated carbide construction and precise geometry support stable chip control and repeatable clamping. Order directly via Metav Werkzeuge or consult our specialists for application-specific advice. CCGT 060200 SH7025 — ISO turning insert for precision turning, Tungaloy CCGT 060200 SH7025 is a rhombic indexable insert designed for external and internal turning, offering a combination of toughness and edge stability for varied machining conditions. ISO CCGT insert for standard turning holders SH7025 coated carbide for edge stability Rhombic 80° shape, 2.38 mm plate thickness One-sided chipbreaker, cylindrical hole with countersink Reliable cutting performance for repeatable turning results The coated carbide composition and the SH7025 grade deliver a balance of toughness and edge stability that reduces unexpected edge chipping under changing engagement conditions. This makes the insert particularly suitable when small tools are used or when cutting conditions vary during a production run. The one-sided chipbreaker supports consistent chip formation, which contributes to smoother cycles and reduced secondary operations. These material and geometry choices translate directly into predictable tool life and more stable component quality. Precise geometry and secure clamping for process security The insert follows the ISO CCGT 060200 standard and is defined by an 80° rhombic shape with a 7° clearance angle, ensuring compatibility with a wide range of standard holders when form, clearance angle, tolerance class, clamping method, size and thickness match. The 2.38 mm plate thickness is part of the dimensional specification that determines fit and clamping reliability. Correct pairing with an appropriate external holder or boring bar and the matching backing/clamping set guarantees repeatable seating and torque distribution, which reduces vibration and wear on the cutting edge. Mounting features and practical assembly considerations The insert is supplied with a cylindrical hole with a single-sided countersink (40°–60°), enabling straightforward centring and secure fastening in many clamping systems. As part of a standard cutting system the arrangement includes the indexable plate, a suitable external holder or boring bar, a backing/clamping set and replacement screws. This modular approach simplifies maintenance and minimises machine downtime, since worn plates are replaced rapidly without regrinding. The physical features of the insert support correct chip flow and reliable mechanical retention under typical turning forces. Application advice and selection guidance for efficient machining Use the rhombic CCGT geometry for general-purpose external and internal turning tasks where moderate approach angles and secure clamping are required. The SH7025 grade was developed for toughness and edge stability, making it a practical choice when entry conditions change or when small tool sizes are necessary. Select the chipbreaker and grade to match the workpiece material and the intended depth of cut: this targeted choice delivers the best compromise between surface finish, tool life and cycle-time efficiency. For additional machining data or to confirm holder compatibility, technical consultation is recommended. Contact Metav Werkzeuge today for detailed application advice, availability and to arrange a tailored recommendation for Tungaloy CCGT 060200 SH7025 inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 6967399-Tungaloy Manufacturer SKU: TUN6967399 Manufacturer article number: 6967399 Manufacturer: Tungaloy Model series: ISO-Drehwendeschneidplatten Facts Plate size: 06 Plate thickness: 2.38 mm Shape angle: 80° Clearance angle: 7° Hole style: cylindrical hole + single-sided countersink (40°–60°) Special features Coating/grade: SH7025 Carbide, coated One-sided chipbreaker Rhombic plate form CCGT Application: turning (external and internal) FAQ What holders are compatible with this insert? Compatibility is determined by form, clearance angle, tolerance class, clamping method, size and thickness; the CCGT 060200 SH7025 requires a holder that accepts ISO CCGT 060200 inserts and secures the plate with the matching backing/clamping set. Which workpieces is this grade intended for? The SH7025 coated carbide grade on the CCGT 060200 insert is intended for applications requiring toughness and edge stability, especially with smaller tools or varying engagement conditions; choose the specific chipbreaker and grade according to the workpiece material and machining strategy. How is the insert fastened and centred in the holder? The indexable plate features a cylindrical hole with a single-sided countersink (40°–60°) to support centring and secure clamping when used with the appropriate screws and clamping set as part of the standard system assembly. What are the key dimensions to check before fitting? Check the 2.38 mm plate thickness, plate size 06, 80° rhombic shape and the 7° clearance angle to ensure the insert matches the intended holder and meets the machine’s clamping requirements. Can this insert be used for both external and internal turning? Yes, the geometry and grade are suitable for both external and internal turning operations when paired with the correct holder and cutting parameters; the CCGT 060200 SH7025 supports versatile turning tasks. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060200 SH7025 Wendeplatten - Tungaloy
Take advantage of the combination of SH7025 grade toughness, ISO-compliant geometry and precise chip control for consistent turning performance; order directly via Metav Werkzeuge or consult the team for application advice. CCGT060200 SH7025 — ISO turning insert for external and internal turning by Tungaloy The CCGT060200 SH7025 is an ISO‑standard rhombic turning insert designed for dependable external and internal turning, offering a durable coated cemented carbide grade for variable engagement conditions. ISO‑compliant rhombic geometry 80° Coated cemented carbide grade SH7025 7° clearance angle, 2.38 mm thickness Single‑sided chipbreaker with countersunk hole Reliable performance from a tough, coated grade The SH7025 grade is a coated cemented carbide developed for high edge stability and reliable cutting performance, especially useful in smaller tools or when engagement conditions change. This insert provides predictable wear behaviour and improved resistance to edge chipping, which translates into longer tool life and fewer interruptions in production. For shops seeking measurable gains in uptime and part consistency, the combination of a robust grade and a controlled chipform offers a clear productivity advantage. Geometry engineered for versatile turning operations The rhombic 80° geometry with a 7° clearance angle and a 2.38 mm thickness balances strength and accessibility: the 80° point gives profile control for external turning while retaining the ability to reach internal contours in many setups. The integrated single‑sided chipbreaker and the insert’s hole with a cylindrical bore plus a one‑side countersink (40°–60°) support secure clamping and effective chip evacuation. These geometric choices reduce vibration and improve surface finish where stability is essential. ISO compatibility and practical selection guidance As an ISO turning insert, compatibility with a toolholder depends on form, clearance, tolerance class, fastening method, size and thickness; these parameters determine correct seating and repeatability. Select the single‑sided chipbreaker and SH7025 grade to match workpiece material and machining stability: choose a tougher grade and stable clamping for interrupted cuts, or maintain the same chip control for continuous finishing passes. If further specification support is required, the technical team at Metav Werkzeuge can advise on holder matching and process optimisation. Contact Metav Werkzeuge for detailed compatibility checks, availability of Tungaloy SH7025 inserts and tailored recommendations — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6967373 SKU: 6967373-Tungaloy Manufacturer SKU: TUN6967373 Designation: CCGT060200 SH7025 Model series: ISO turning inserts Application: Turning Facts Insert geometry angle: 80° Clearance angle: 7° Thickness: 2.38 mm Size: 06 ISO code: 060200 Countersink angle range: 40°–60° Special features Rhombic insert form Single‑sided chipbreaker With hole: cylindrical hole + one‑side countersink (40°–60°) Coated cemented carbide, grade SH7025 ISO‑standardised dimensions and fit Compatibility determined by form, clearance, tolerance class, fastening, size and thickness FAQ What materials is this insert suited for? The CCGT060200 SH7025 insert is suitable for a wide range of turning tasks where a tougher, edge‑stable coated cemented carbide is required; the specific workpiece material should be matched to the SH7025 grade and chipbreaker choice. How does the 80° geometry affect application? An 80° rhombic geometry provides a robust cutting edge for external turning and allows access to many internal contours, giving a good compromise between profile control and strength. How is holder compatibility ensured for this ISO insert? Compatibility depends on the insert form, clearance angle, tolerance class, fastening method, size and thickness; ensuring the holder matches the ISO code 060200 and the 2.38 mm thickness secures repeatable seating. What benefit does the single‑sided chipbreaker give? A single‑sided chipbreaker offers controlled chip formation and evacuation for many turning operations, improving surface finish and reducing the risk of entanglement in unstable conditions. What does the SH7025 grade provide compared with general grades? SH7025 is formulated for toughness and edge stability, making it particularly effective for smaller tools or varying engagement, where consistent edge integrity reduces downtime. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 060200 SH725 Wendeplatten - Tungaloy
Take advantage of the combination of tough SH725 grade, ISO conformity and a secure mounting design to achieve stable cutting and predictable tool life; order supply or request application guidance from Metav Werkzeuge for smooth production flow. CCGT060200 SH725 Tungaloy indexable turning insert — coated carbide, 7° clearance The CCGT060200 SH725 is an ISO‑standard rhombic indexable insert designed for external and internal turning, offering a tough coated cemented‑carbide grade suited to varying engagement conditions. Coated cemented‑carbide grade SH725 Rhombic 80° geometry with 7° clearance Central hole with cylindrical + countersink ISO‑standard 060200 for consistent indexing Stable cutting performance where toughness matters The SH725 grade is a coated cemented‑carbide designed for applications that demand edge stability and resistance to chipping under variable conditions. In practice, this means fewer unexpected tool changes and longer effective life of the cutting edge. The rhombic geometry with an included angle of 80° delivers a robust contact area, while the 7° clearance reduces flank rubbing and heat build‑up; together these factors help maintain consistent cutting forces and surface quality during turning operations. Secure clamping and straightforward tool selection Compatibility with toolholders is determined by form, clearance, tolerance class, fastening, size and thickness; the ISO designation ensures predictable fitment across standard holders. The central cylindrical hole with a single‑side countersink (40°–60°) provides reliable location and secure clamping, reducing vibration and improving repeatability. The insert’s single‑sided chipbreaker offers controlled chip formation for common turning tasks, simplifying selection of cutting parameters and minimising cycle‑time variability on the shop floor. Versatile use for external and internal turning Designed for general turning, the insert adapts to a range of workpiece materials when the correct chipbreaker and cutting data are chosen. The rhombic shape enables favourable approach angles for both finishing and semi‑finishing, while the coated substrate supports machining where small tools or fluctuating engagement occur. For less experienced personnel, the chipbreaker function channels chips away from the cutting zone and helps achieve a consistent surface finish without complex parameter tuning. Practical integration into production workflows The ISO‑compliant designation and compact size (size 06, thickness 2.38 mm) make this insert easy to stock and rotate in multi‑tool setups. Its coated substrate (SH725) focuses on wear resistance and edge reliability rather than aggressive hardness, so it is particularly suitable when stability and repeatable part quality are priorities. Application notes and cutting‑data charts from the supplier help to translate these design features into measurable productivity gains and lower scrap rates on turning centres. For workshop‑grade toughness and repeatable turning performance, contact Metav Werkzeuge for supply and tailored cutting data for Tungaloy inserts: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 6737126 Manufacturer SKU: TUN6737126 SKU: 6737126-Tungaloy Model series: ISO indexable turning inserts Designation: CCGT060200 SH725 Manufacturer: Tungaloy Facts Geometry angle: 80° Clearance angle: 7° Thickness: 2.38 mm Size: 06 Countersink angle: 40°–60° Manufacturer article number: 6737126 Special features Coated cemented‑carbide (SH725) Rhombic plate shape Single‑sided chipbreaker Cylindrical hole with one‑side countersink ISO designation 060200 Suitable for external and internal turning FAQ What toolholders are compatible with this insert? The CCGT060200 SH725 indexable insert fits ISO‑standard toolholders that accept CCGT‑style inserts; compatibility depends on form, clearance, tolerance class, fastening, size and thickness. Which materials is the SH725 grade best suited to machine? The SH725 coated cemented‑carbide grade is intended for applications requiring edge stability under varying engagement rather than exclusively high‑speed finishing; select the chipbreaker and cutting data according to the specific workpiece material and operation. How does the single‑sided chipbreaker affect chip control? A single‑sided chipbreaker promotes predictable chip formation and evacuation during turning, helping to reduce entanglement and improve surface finish when using the CCGT060200 SH725 insert. Is the insert indexed and reversible? The ISO‑standard CCGT060200 insert provides consistent indexing; the rhombic form allows multiple edge positions where the insert design supports re‑indexing according to the holder system. What does the 7° clearance angle mean for machining results? A 7° clearance angle reduces flank contact with the workpiece, lowering friction and heat at the cutting edge; this contributes to longer edge life and more stable machining conditions with the SH725 grade. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 060200 SH725 Wendeplatten - Tungaloy
Benefit from the combination of a coated carbide SH725 grade, an 80° rhombic geometry and a precise 7° clearance angle to achieve stable edge life and adaptable performance in turning operations; order the insert directly via Metav Werkzeuge or consult our technical advisors for sizing and holder compatibility. CCGT060200 SH725 CCGT 060200 for Turning — Tungaloy A CCGT060200 SH725 indexable turning insert designed for ISO‑conforming external and internal turning tasks, offering a robust, edge‑stable grade for varying engagement conditions. ISO rhombic insert, 80° geometry SH725 coated carbide for stable edge life 7° clearance angle for reliable chip flow Cylindrical hole with single‑side countersink Consistent cutting performance for mixed turning conditions The CCGT060200 SH725 insert combines a coated carbide substrate with a grade designed for toughness and edge stability. This turning grade is particularly suited to small‑tool applications and situations with changing engagement, where repetitive edge reliability reduces downtime. The SH725 coating enhances wear resistance without sacrificing toughness, meaning longer intervals between index changes and a predictable tool life. For production environments this translates into improved process stability and fewer unexpected tool stops, supporting efficient CNC turning operations. Secure clamping and straightforward compatibility with ISO systems Compatibility with the toolholder is determined by form, clearance angle, tolerance class, attachment, size and thickness; the rhombic profile and a cylindrical hole with a single‑side countersink (40°–60°) provide a straightforward, repeatable clamping interface. The insert’s 7° clearance ensures the cutting edge clears the workpiece correctly, helping to avoid rubbing and heat build‑up. Because the insert follows ISO specifications, it integrates into established holder systems, simplifying tool inventory and reducing the need for bespoke components. Controlled chip formation and reliable surface results Chip control is achieved through a single‑sided chipbreaker optimised for turning; combined with the insert geometry this promotes predictable chip shapes and evacuation in a wide range of feed and depth‑of‑cut scenarios. Predictable chip behaviour reduces the risk of rework and improves surface finish, which is particularly valuable when cycle times and quality standards are both critical. For machinists seeking consistent part quality, the balance between chip control and edge stability offered here supports repeatable surface integrity. Practical benefits for everyday workshop use From a shop‑floor perspective the insert’s 2.38 mm thickness and 06 size deliver a compact solution that is easy to handle and economical in multi‑station setups. The 80° included angle broadens applicability for both external and internal turning, while the coated carbide construction provides a combination of toughness and wear resistance suited to general turning tasks. When matched with an appropriate chipbreaker and holder, this insert supports a productive turning routine with predictable maintenance intervals and straightforward stock management. For tailored advice on integrating the Tungaloy SH725 insert into production, contact Metav Werkzeuge for consultation and order processing via info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists will assist with holder compatibility and cutting parameters. Technical Data Article number: 6736612 Manufacturer SKU: TUN6736612 SKU: 6736612-Tungaloy Designation: CCGT060200 SH725 Tungaloy turning insert Facts Size: 06 Thickness: 2.38 mm Clearance angle: 7° Included angle: 80° Special features Grade/coating: SH725 (coated carbide) Shape: rhombic Hole: with cylindrical hole + single‑side countersink (40°–60°) Chipbreaker: single‑sided Series: ISO indexable turning inserts Application: turning FAQ What advantages does the 80° geometry provide? The 80° geometry offers robust support for the cutting edge and broad applicability in both external and internal turning; the CCGT060200 SH725 insert uses this geometry to improve stability and allow safe cuts at varied engagement angles. How is holder compatibility determined for this insert? Compatibility depends on the insert form, clearance, tolerance class, attachment method, size and thickness; the ISO‑conforming design of the Tungaloy CCGT060200 facilitates selection of matching holders and clamping kits. What does the SH725 designation mean for performance? SH725 identifies a coated carbide grade engineered for toughness and edge stability; in practice the grade supports consistent cutting edges and is effective for smaller tools or when engagement conditions change. How does the chipbreaker and hole design affect chip control? The single‑sided chipbreaker, together with the rhombic profile and cylindrical hole with countersink, promotes predictable chip formation and secure clamping, improving evacuation and surface quality for turning operations. Can this insert be used for internal turning as well as external? Yes, the insert is suitable for both external and internal turning when matched with the correct holder and cutting parameters; the ISO standard form and 80° geometry expand its versatility. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Why indexable inserts are indispensable in modern machining
Indexable inserts, also known as cutting inserts or indexable cutting inserts, are standardised, replaceable cutting elements that mount on tool holders such as turning bits, milling cutters or drills. Made from wear-resistant materials like carbide, cermet, ceramic or other superhard grades, they carry the actual cutting edge and allow a worn corner to be rotated or flipped instead of replacing or regrinding the entire tool body.
How these inserts work and when to choose them
In everyday workshop and production settings, indexable inserts perform the direct material removal on the workpiece. Standard inserts for tool systems without internal coolant typically feature closed faces or a single central fixing hole, with heat evacuation handled by external machine nozzles. Inserts designed for systems with internal coolant are engineered to support coolant flow: they include calculated chipbreaker geometries that guide an internal coolant jet under the chip or, in specialised designs, contain sintered microchannels to direct coolant right to the cutting edge. Such coolant-compatible inserts are essential for machining heat-resistant alloys, heavy cutting operations and deep internal machining, where thermal load and chip control are critical.
Tangible benefits for production and workshop efficiency
Choosing the right indexable inserts delivers measurable operational advantages:
- Reduced downtime: faster changeover because a worn insert is simply indexed rather than the whole tool being replaced.
- Extended cutting-edge life: targeted coolant application and optimised chipbreaker design lower thermal stress and improve tool life.
- Consistent part quality: predictable cutting-edge geometry from standardised inserts maintains tolerances across batches.
- Versatility: availability in carbide, cermet, ceramic and superhard grades permits selection according to workpiece material and cutting conditions.
- Lower tooling costs over time: fewer full-tool replacements and less regrinding required.
Metav as a dependable source for inserts and tooling systems
Metav combines decades of precision expertise with a wide-ranging supply chain, positioning itself as a practical partner for industry, craft and trade. From Emmerich on the Rhine, Metav operates as a quality filter for the European market, offering more than 250,000 products and serving over 48,000 customers. For procurement teams aiming to reduce supplier count while retaining technical reliability, Metav’s assortment of indexable inserts and compatible tool holders provides a central, trustworthy solution.
Quick summary
Indexable inserts (cutting inserts or indexable cutting inserts) enable economical, repeatable material removal by allowing worn cutting edges to be indexed or replaced quickly; coolant-adapted designs further reduce thermal load and enhance chip control for demanding applications.
FAQ
What materials are indexable inserts available in?
Indexable inserts are available in wear-resistant grades such as carbide, cermet, ceramic and other superhard materials, selected according to the workpiece material and cutting conditions.
When should I choose inserts with internal coolant support?
Choose inserts designed for internal coolant when machining heat-resistant alloys, performing heavy cuts or working in deep internal features, because the coolant reduces thermal load at the cutting edge and actively improves chip breakage.
How do chipbreaker geometries affect performance?
Chipbreaker geometries on indexable inserts guide the chip flow and, when matched to an internal coolant jet, direct the coolant under the chip to control temperature and facilitate reliable chip formation, which extends edge life and stabilises machining.
Can standard inserts be used with external coolant only?
Yes; standard inserts for tool systems without internal coolant typically have closed faces or a central fixing hole and rely on external machine nozzles for heat evacuation, which is sufficient for many routine, accessible cuts.
Why source inserts through Metav?
Metav supplies a broad range of indexable inserts and tooling, backed by decades of expertise and a comprehensive European stock, making it a practical choice for consistent quality and dependable delivery.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com